1 /* 2 * Copyright (C) 2009 Samsung Electronics Ltd. 3 * Jaswinder Singh <jassi.brar@samsung.com> 4 * 5 * This program is free software; you can redistribute it and/or modify 6 * it under the terms of the GNU General Public License as published by 7 * the Free Software Foundation; either version 2 of the License, or 8 * (at your option) any later version. 9 * 10 * This program is distributed in the hope that it will be useful, 11 * but WITHOUT ANY WARRANTY; without even the implied warranty of 12 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 13 * GNU General Public License for more details. 14 * 15 * You should have received a copy of the GNU General Public License 16 * along with this program; if not, write to the Free Software 17 * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 18 */ 19 20 #include <linux/init.h> 21 #include <linux/module.h> 22 #include <linux/workqueue.h> 23 #include <linux/interrupt.h> 24 #include <linux/delay.h> 25 #include <linux/clk.h> 26 #include <linux/dma-mapping.h> 27 #include <linux/dmaengine.h> 28 #include <linux/platform_device.h> 29 #include <linux/pm_runtime.h> 30 #include <linux/spi/spi.h> 31 #include <linux/gpio.h> 32 #include <linux/of.h> 33 #include <linux/of_gpio.h> 34 35 #include <linux/platform_data/spi-s3c64xx.h> 36 37 #ifdef CONFIG_S3C_DMA 38 #include <mach/dma.h> 39 #endif 40 41 #define MAX_SPI_PORTS 3 42 #define S3C64XX_SPI_QUIRK_POLL (1 << 0) 43 44 /* Registers and bit-fields */ 45 46 #define S3C64XX_SPI_CH_CFG 0x00 47 #define S3C64XX_SPI_CLK_CFG 0x04 48 #define S3C64XX_SPI_MODE_CFG 0x08 49 #define S3C64XX_SPI_SLAVE_SEL 0x0C 50 #define S3C64XX_SPI_INT_EN 0x10 51 #define S3C64XX_SPI_STATUS 0x14 52 #define S3C64XX_SPI_TX_DATA 0x18 53 #define S3C64XX_SPI_RX_DATA 0x1C 54 #define S3C64XX_SPI_PACKET_CNT 0x20 55 #define S3C64XX_SPI_PENDING_CLR 0x24 56 #define S3C64XX_SPI_SWAP_CFG 0x28 57 #define S3C64XX_SPI_FB_CLK 0x2C 58 59 #define S3C64XX_SPI_CH_HS_EN (1<<6) /* High Speed Enable */ 60 #define S3C64XX_SPI_CH_SW_RST (1<<5) 61 #define S3C64XX_SPI_CH_SLAVE (1<<4) 62 #define S3C64XX_SPI_CPOL_L (1<<3) 63 #define S3C64XX_SPI_CPHA_B (1<<2) 64 #define S3C64XX_SPI_CH_RXCH_ON (1<<1) 65 #define S3C64XX_SPI_CH_TXCH_ON (1<<0) 66 67 #define S3C64XX_SPI_CLKSEL_SRCMSK (3<<9) 68 #define S3C64XX_SPI_CLKSEL_SRCSHFT 9 69 #define S3C64XX_SPI_ENCLK_ENABLE (1<<8) 70 #define S3C64XX_SPI_PSR_MASK 0xff 71 72 #define S3C64XX_SPI_MODE_CH_TSZ_BYTE (0<<29) 73 #define S3C64XX_SPI_MODE_CH_TSZ_HALFWORD (1<<29) 74 #define S3C64XX_SPI_MODE_CH_TSZ_WORD (2<<29) 75 #define S3C64XX_SPI_MODE_CH_TSZ_MASK (3<<29) 76 #define S3C64XX_SPI_MODE_BUS_TSZ_BYTE (0<<17) 77 #define S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD (1<<17) 78 #define S3C64XX_SPI_MODE_BUS_TSZ_WORD (2<<17) 79 #define S3C64XX_SPI_MODE_BUS_TSZ_MASK (3<<17) 80 #define S3C64XX_SPI_MODE_RXDMA_ON (1<<2) 81 #define S3C64XX_SPI_MODE_TXDMA_ON (1<<1) 82 #define S3C64XX_SPI_MODE_4BURST (1<<0) 83 84 #define S3C64XX_SPI_SLAVE_AUTO (1<<1) 85 #define S3C64XX_SPI_SLAVE_SIG_INACT (1<<0) 86 87 #define S3C64XX_SPI_INT_TRAILING_EN (1<<6) 88 #define S3C64XX_SPI_INT_RX_OVERRUN_EN (1<<5) 89 #define S3C64XX_SPI_INT_RX_UNDERRUN_EN (1<<4) 90 #define S3C64XX_SPI_INT_TX_OVERRUN_EN (1<<3) 91 #define S3C64XX_SPI_INT_TX_UNDERRUN_EN (1<<2) 92 #define S3C64XX_SPI_INT_RX_FIFORDY_EN (1<<1) 93 #define S3C64XX_SPI_INT_TX_FIFORDY_EN (1<<0) 94 95 #define S3C64XX_SPI_ST_RX_OVERRUN_ERR (1<<5) 96 #define S3C64XX_SPI_ST_RX_UNDERRUN_ERR (1<<4) 97 #define S3C64XX_SPI_ST_TX_OVERRUN_ERR (1<<3) 98 #define S3C64XX_SPI_ST_TX_UNDERRUN_ERR (1<<2) 99 #define S3C64XX_SPI_ST_RX_FIFORDY (1<<1) 100 #define S3C64XX_SPI_ST_TX_FIFORDY (1<<0) 101 102 #define S3C64XX_SPI_PACKET_CNT_EN (1<<16) 103 104 #define S3C64XX_SPI_PND_TX_UNDERRUN_CLR (1<<4) 105 #define S3C64XX_SPI_PND_TX_OVERRUN_CLR (1<<3) 106 #define S3C64XX_SPI_PND_RX_UNDERRUN_CLR (1<<2) 107 #define S3C64XX_SPI_PND_RX_OVERRUN_CLR (1<<1) 108 #define S3C64XX_SPI_PND_TRAILING_CLR (1<<0) 109 110 #define S3C64XX_SPI_SWAP_RX_HALF_WORD (1<<7) 111 #define S3C64XX_SPI_SWAP_RX_BYTE (1<<6) 112 #define S3C64XX_SPI_SWAP_RX_BIT (1<<5) 113 #define S3C64XX_SPI_SWAP_RX_EN (1<<4) 114 #define S3C64XX_SPI_SWAP_TX_HALF_WORD (1<<3) 115 #define S3C64XX_SPI_SWAP_TX_BYTE (1<<2) 116 #define S3C64XX_SPI_SWAP_TX_BIT (1<<1) 117 #define S3C64XX_SPI_SWAP_TX_EN (1<<0) 118 119 #define S3C64XX_SPI_FBCLK_MSK (3<<0) 120 121 #define FIFO_LVL_MASK(i) ((i)->port_conf->fifo_lvl_mask[i->port_id]) 122 #define S3C64XX_SPI_ST_TX_DONE(v, i) (((v) & \ 123 (1 << (i)->port_conf->tx_st_done)) ? 1 : 0) 124 #define TX_FIFO_LVL(v, i) (((v) >> 6) & FIFO_LVL_MASK(i)) 125 #define RX_FIFO_LVL(v, i) (((v) >> (i)->port_conf->rx_lvl_offset) & \ 126 FIFO_LVL_MASK(i)) 127 128 #define S3C64XX_SPI_MAX_TRAILCNT 0x3ff 129 #define S3C64XX_SPI_TRAILCNT_OFF 19 130 131 #define S3C64XX_SPI_TRAILCNT S3C64XX_SPI_MAX_TRAILCNT 132 133 #define msecs_to_loops(t) (loops_per_jiffy / 1000 * HZ * t) 134 #define is_polling(x) (x->port_conf->quirks & S3C64XX_SPI_QUIRK_POLL) 135 136 #define RXBUSY (1<<2) 137 #define TXBUSY (1<<3) 138 139 struct s3c64xx_spi_dma_data { 140 struct dma_chan *ch; 141 enum dma_transfer_direction direction; 142 unsigned int dmach; 143 }; 144 145 /** 146 * struct s3c64xx_spi_info - SPI Controller hardware info 147 * @fifo_lvl_mask: Bit-mask for {TX|RX}_FIFO_LVL bits in SPI_STATUS register. 148 * @rx_lvl_offset: Bit offset of RX_FIFO_LVL bits in SPI_STATUS regiter. 149 * @tx_st_done: Bit offset of TX_DONE bit in SPI_STATUS regiter. 150 * @high_speed: True, if the controller supports HIGH_SPEED_EN bit. 151 * @clk_from_cmu: True, if the controller does not include a clock mux and 152 * prescaler unit. 153 * 154 * The Samsung s3c64xx SPI controller are used on various Samsung SoC's but 155 * differ in some aspects such as the size of the fifo and spi bus clock 156 * setup. Such differences are specified to the driver using this structure 157 * which is provided as driver data to the driver. 158 */ 159 struct s3c64xx_spi_port_config { 160 int fifo_lvl_mask[MAX_SPI_PORTS]; 161 int rx_lvl_offset; 162 int tx_st_done; 163 int quirks; 164 bool high_speed; 165 bool clk_from_cmu; 166 }; 167 168 /** 169 * struct s3c64xx_spi_driver_data - Runtime info holder for SPI driver. 170 * @clk: Pointer to the spi clock. 171 * @src_clk: Pointer to the clock used to generate SPI signals. 172 * @master: Pointer to the SPI Protocol master. 173 * @cntrlr_info: Platform specific data for the controller this driver manages. 174 * @tgl_spi: Pointer to the last CS left untoggled by the cs_change hint. 175 * @lock: Controller specific lock. 176 * @state: Set of FLAGS to indicate status. 177 * @rx_dmach: Controller's DMA channel for Rx. 178 * @tx_dmach: Controller's DMA channel for Tx. 179 * @sfr_start: BUS address of SPI controller regs. 180 * @regs: Pointer to ioremap'ed controller registers. 181 * @irq: interrupt 182 * @xfer_completion: To indicate completion of xfer task. 183 * @cur_mode: Stores the active configuration of the controller. 184 * @cur_bpw: Stores the active bits per word settings. 185 * @cur_speed: Stores the active xfer clock speed. 186 */ 187 struct s3c64xx_spi_driver_data { 188 void __iomem *regs; 189 struct clk *clk; 190 struct clk *src_clk; 191 struct platform_device *pdev; 192 struct spi_master *master; 193 struct s3c64xx_spi_info *cntrlr_info; 194 struct spi_device *tgl_spi; 195 spinlock_t lock; 196 unsigned long sfr_start; 197 struct completion xfer_completion; 198 unsigned state; 199 unsigned cur_mode, cur_bpw; 200 unsigned cur_speed; 201 struct s3c64xx_spi_dma_data rx_dma; 202 struct s3c64xx_spi_dma_data tx_dma; 203 #ifdef CONFIG_S3C_DMA 204 struct samsung_dma_ops *ops; 205 #endif 206 struct s3c64xx_spi_port_config *port_conf; 207 unsigned int port_id; 208 unsigned long gpios[4]; 209 bool cs_gpio; 210 }; 211 212 static void flush_fifo(struct s3c64xx_spi_driver_data *sdd) 213 { 214 void __iomem *regs = sdd->regs; 215 unsigned long loops; 216 u32 val; 217 218 writel(0, regs + S3C64XX_SPI_PACKET_CNT); 219 220 val = readl(regs + S3C64XX_SPI_CH_CFG); 221 val &= ~(S3C64XX_SPI_CH_RXCH_ON | S3C64XX_SPI_CH_TXCH_ON); 222 writel(val, regs + S3C64XX_SPI_CH_CFG); 223 224 val = readl(regs + S3C64XX_SPI_CH_CFG); 225 val |= S3C64XX_SPI_CH_SW_RST; 226 val &= ~S3C64XX_SPI_CH_HS_EN; 227 writel(val, regs + S3C64XX_SPI_CH_CFG); 228 229 /* Flush TxFIFO*/ 230 loops = msecs_to_loops(1); 231 do { 232 val = readl(regs + S3C64XX_SPI_STATUS); 233 } while (TX_FIFO_LVL(val, sdd) && loops--); 234 235 if (loops == 0) 236 dev_warn(&sdd->pdev->dev, "Timed out flushing TX FIFO\n"); 237 238 /* Flush RxFIFO*/ 239 loops = msecs_to_loops(1); 240 do { 241 val = readl(regs + S3C64XX_SPI_STATUS); 242 if (RX_FIFO_LVL(val, sdd)) 243 readl(regs + S3C64XX_SPI_RX_DATA); 244 else 245 break; 246 } while (loops--); 247 248 if (loops == 0) 249 dev_warn(&sdd->pdev->dev, "Timed out flushing RX FIFO\n"); 250 251 val = readl(regs + S3C64XX_SPI_CH_CFG); 252 val &= ~S3C64XX_SPI_CH_SW_RST; 253 writel(val, regs + S3C64XX_SPI_CH_CFG); 254 255 val = readl(regs + S3C64XX_SPI_MODE_CFG); 256 val &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON); 257 writel(val, regs + S3C64XX_SPI_MODE_CFG); 258 } 259 260 static void s3c64xx_spi_dmacb(void *data) 261 { 262 struct s3c64xx_spi_driver_data *sdd; 263 struct s3c64xx_spi_dma_data *dma = data; 264 unsigned long flags; 265 266 if (dma->direction == DMA_DEV_TO_MEM) 267 sdd = container_of(data, 268 struct s3c64xx_spi_driver_data, rx_dma); 269 else 270 sdd = container_of(data, 271 struct s3c64xx_spi_driver_data, tx_dma); 272 273 spin_lock_irqsave(&sdd->lock, flags); 274 275 if (dma->direction == DMA_DEV_TO_MEM) { 276 sdd->state &= ~RXBUSY; 277 if (!(sdd->state & TXBUSY)) 278 complete(&sdd->xfer_completion); 279 } else { 280 sdd->state &= ~TXBUSY; 281 if (!(sdd->state & RXBUSY)) 282 complete(&sdd->xfer_completion); 283 } 284 285 spin_unlock_irqrestore(&sdd->lock, flags); 286 } 287 288 #ifdef CONFIG_S3C_DMA 289 /* FIXME: remove this section once arch/arm/mach-s3c64xx uses dmaengine */ 290 291 static struct s3c2410_dma_client s3c64xx_spi_dma_client = { 292 .name = "samsung-spi-dma", 293 }; 294 295 static void prepare_dma(struct s3c64xx_spi_dma_data *dma, 296 unsigned len, dma_addr_t buf) 297 { 298 struct s3c64xx_spi_driver_data *sdd; 299 struct samsung_dma_prep info; 300 struct samsung_dma_config config; 301 302 if (dma->direction == DMA_DEV_TO_MEM) { 303 sdd = container_of((void *)dma, 304 struct s3c64xx_spi_driver_data, rx_dma); 305 config.direction = sdd->rx_dma.direction; 306 config.fifo = sdd->sfr_start + S3C64XX_SPI_RX_DATA; 307 config.width = sdd->cur_bpw / 8; 308 sdd->ops->config((enum dma_ch)sdd->rx_dma.ch, &config); 309 } else { 310 sdd = container_of((void *)dma, 311 struct s3c64xx_spi_driver_data, tx_dma); 312 config.direction = sdd->tx_dma.direction; 313 config.fifo = sdd->sfr_start + S3C64XX_SPI_TX_DATA; 314 config.width = sdd->cur_bpw / 8; 315 sdd->ops->config((enum dma_ch)sdd->tx_dma.ch, &config); 316 } 317 318 info.cap = DMA_SLAVE; 319 info.len = len; 320 info.fp = s3c64xx_spi_dmacb; 321 info.fp_param = dma; 322 info.direction = dma->direction; 323 info.buf = buf; 324 325 sdd->ops->prepare((enum dma_ch)dma->ch, &info); 326 sdd->ops->trigger((enum dma_ch)dma->ch); 327 } 328 329 static int acquire_dma(struct s3c64xx_spi_driver_data *sdd) 330 { 331 struct samsung_dma_req req; 332 struct device *dev = &sdd->pdev->dev; 333 334 sdd->ops = samsung_dma_get_ops(); 335 336 req.cap = DMA_SLAVE; 337 req.client = &s3c64xx_spi_dma_client; 338 339 sdd->rx_dma.ch = (struct dma_chan *)(unsigned long)sdd->ops->request( 340 sdd->rx_dma.dmach, &req, dev, "rx"); 341 sdd->tx_dma.ch = (struct dma_chan *)(unsigned long)sdd->ops->request( 342 sdd->tx_dma.dmach, &req, dev, "tx"); 343 344 return 1; 345 } 346 347 static int s3c64xx_spi_prepare_transfer(struct spi_master *spi) 348 { 349 struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(spi); 350 351 /* 352 * If DMA resource was not available during 353 * probe, no need to continue with dma requests 354 * else Acquire DMA channels 355 */ 356 while (!is_polling(sdd) && !acquire_dma(sdd)) 357 usleep_range(10000, 11000); 358 359 return 0; 360 } 361 362 static int s3c64xx_spi_unprepare_transfer(struct spi_master *spi) 363 { 364 struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(spi); 365 366 /* Free DMA channels */ 367 if (!is_polling(sdd)) { 368 sdd->ops->release((enum dma_ch)sdd->rx_dma.ch, 369 &s3c64xx_spi_dma_client); 370 sdd->ops->release((enum dma_ch)sdd->tx_dma.ch, 371 &s3c64xx_spi_dma_client); 372 } 373 374 return 0; 375 } 376 377 static void s3c64xx_spi_dma_stop(struct s3c64xx_spi_driver_data *sdd, 378 struct s3c64xx_spi_dma_data *dma) 379 { 380 sdd->ops->stop((enum dma_ch)dma->ch); 381 } 382 #else 383 384 static void prepare_dma(struct s3c64xx_spi_dma_data *dma, 385 unsigned len, dma_addr_t buf) 386 { 387 struct s3c64xx_spi_driver_data *sdd; 388 struct dma_slave_config config; 389 struct dma_async_tx_descriptor *desc; 390 391 memset(&config, 0, sizeof(config)); 392 393 if (dma->direction == DMA_DEV_TO_MEM) { 394 sdd = container_of((void *)dma, 395 struct s3c64xx_spi_driver_data, rx_dma); 396 config.direction = dma->direction; 397 config.src_addr = sdd->sfr_start + S3C64XX_SPI_RX_DATA; 398 config.src_addr_width = sdd->cur_bpw / 8; 399 config.src_maxburst = 1; 400 dmaengine_slave_config(dma->ch, &config); 401 } else { 402 sdd = container_of((void *)dma, 403 struct s3c64xx_spi_driver_data, tx_dma); 404 config.direction = dma->direction; 405 config.dst_addr = sdd->sfr_start + S3C64XX_SPI_TX_DATA; 406 config.dst_addr_width = sdd->cur_bpw / 8; 407 config.dst_maxburst = 1; 408 dmaengine_slave_config(dma->ch, &config); 409 } 410 411 desc = dmaengine_prep_slave_single(dma->ch, buf, len, 412 dma->direction, DMA_PREP_INTERRUPT); 413 414 desc->callback = s3c64xx_spi_dmacb; 415 desc->callback_param = dma; 416 417 dmaengine_submit(desc); 418 dma_async_issue_pending(dma->ch); 419 } 420 421 static int s3c64xx_spi_prepare_transfer(struct spi_master *spi) 422 { 423 struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(spi); 424 dma_filter_fn filter = sdd->cntrlr_info->filter; 425 struct device *dev = &sdd->pdev->dev; 426 dma_cap_mask_t mask; 427 int ret; 428 429 if (!is_polling(sdd)) { 430 dma_cap_zero(mask); 431 dma_cap_set(DMA_SLAVE, mask); 432 433 /* Acquire DMA channels */ 434 sdd->rx_dma.ch = dma_request_slave_channel_compat(mask, filter, 435 (void *)sdd->rx_dma.dmach, dev, "rx"); 436 if (!sdd->rx_dma.ch) { 437 dev_err(dev, "Failed to get RX DMA channel\n"); 438 ret = -EBUSY; 439 goto out; 440 } 441 442 sdd->tx_dma.ch = dma_request_slave_channel_compat(mask, filter, 443 (void *)sdd->tx_dma.dmach, dev, "tx"); 444 if (!sdd->tx_dma.ch) { 445 dev_err(dev, "Failed to get TX DMA channel\n"); 446 ret = -EBUSY; 447 goto out_rx; 448 } 449 } 450 451 ret = pm_runtime_get_sync(&sdd->pdev->dev); 452 if (ret < 0) { 453 dev_err(dev, "Failed to enable device: %d\n", ret); 454 goto out_tx; 455 } 456 457 return 0; 458 459 out_tx: 460 dma_release_channel(sdd->tx_dma.ch); 461 out_rx: 462 dma_release_channel(sdd->rx_dma.ch); 463 out: 464 return ret; 465 } 466 467 static int s3c64xx_spi_unprepare_transfer(struct spi_master *spi) 468 { 469 struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(spi); 470 471 /* Free DMA channels */ 472 if (!is_polling(sdd)) { 473 dma_release_channel(sdd->rx_dma.ch); 474 dma_release_channel(sdd->tx_dma.ch); 475 } 476 477 pm_runtime_put(&sdd->pdev->dev); 478 return 0; 479 } 480 481 static void s3c64xx_spi_dma_stop(struct s3c64xx_spi_driver_data *sdd, 482 struct s3c64xx_spi_dma_data *dma) 483 { 484 dmaengine_terminate_all(dma->ch); 485 } 486 #endif 487 488 static void enable_datapath(struct s3c64xx_spi_driver_data *sdd, 489 struct spi_device *spi, 490 struct spi_transfer *xfer, int dma_mode) 491 { 492 void __iomem *regs = sdd->regs; 493 u32 modecfg, chcfg; 494 495 modecfg = readl(regs + S3C64XX_SPI_MODE_CFG); 496 modecfg &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON); 497 498 chcfg = readl(regs + S3C64XX_SPI_CH_CFG); 499 chcfg &= ~S3C64XX_SPI_CH_TXCH_ON; 500 501 if (dma_mode) { 502 chcfg &= ~S3C64XX_SPI_CH_RXCH_ON; 503 } else { 504 /* Always shift in data in FIFO, even if xfer is Tx only, 505 * this helps setting PCKT_CNT value for generating clocks 506 * as exactly needed. 507 */ 508 chcfg |= S3C64XX_SPI_CH_RXCH_ON; 509 writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff) 510 | S3C64XX_SPI_PACKET_CNT_EN, 511 regs + S3C64XX_SPI_PACKET_CNT); 512 } 513 514 if (xfer->tx_buf != NULL) { 515 sdd->state |= TXBUSY; 516 chcfg |= S3C64XX_SPI_CH_TXCH_ON; 517 if (dma_mode) { 518 modecfg |= S3C64XX_SPI_MODE_TXDMA_ON; 519 prepare_dma(&sdd->tx_dma, xfer->len, xfer->tx_dma); 520 } else { 521 switch (sdd->cur_bpw) { 522 case 32: 523 iowrite32_rep(regs + S3C64XX_SPI_TX_DATA, 524 xfer->tx_buf, xfer->len / 4); 525 break; 526 case 16: 527 iowrite16_rep(regs + S3C64XX_SPI_TX_DATA, 528 xfer->tx_buf, xfer->len / 2); 529 break; 530 default: 531 iowrite8_rep(regs + S3C64XX_SPI_TX_DATA, 532 xfer->tx_buf, xfer->len); 533 break; 534 } 535 } 536 } 537 538 if (xfer->rx_buf != NULL) { 539 sdd->state |= RXBUSY; 540 541 if (sdd->port_conf->high_speed && sdd->cur_speed >= 30000000UL 542 && !(sdd->cur_mode & SPI_CPHA)) 543 chcfg |= S3C64XX_SPI_CH_HS_EN; 544 545 if (dma_mode) { 546 modecfg |= S3C64XX_SPI_MODE_RXDMA_ON; 547 chcfg |= S3C64XX_SPI_CH_RXCH_ON; 548 writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff) 549 | S3C64XX_SPI_PACKET_CNT_EN, 550 regs + S3C64XX_SPI_PACKET_CNT); 551 prepare_dma(&sdd->rx_dma, xfer->len, xfer->rx_dma); 552 } 553 } 554 555 writel(modecfg, regs + S3C64XX_SPI_MODE_CFG); 556 writel(chcfg, regs + S3C64XX_SPI_CH_CFG); 557 } 558 559 static inline void enable_cs(struct s3c64xx_spi_driver_data *sdd, 560 struct spi_device *spi) 561 { 562 struct s3c64xx_spi_csinfo *cs; 563 564 if (sdd->tgl_spi != NULL) { /* If last device toggled after mssg */ 565 if (sdd->tgl_spi != spi) { /* if last mssg on diff device */ 566 /* Deselect the last toggled device */ 567 cs = sdd->tgl_spi->controller_data; 568 if (sdd->cs_gpio) 569 gpio_set_value(cs->line, 570 spi->mode & SPI_CS_HIGH ? 0 : 1); 571 } 572 sdd->tgl_spi = NULL; 573 } 574 575 cs = spi->controller_data; 576 if (sdd->cs_gpio) 577 gpio_set_value(cs->line, spi->mode & SPI_CS_HIGH ? 1 : 0); 578 579 /* Start the signals */ 580 writel(0, sdd->regs + S3C64XX_SPI_SLAVE_SEL); 581 } 582 583 static u32 s3c64xx_spi_wait_for_timeout(struct s3c64xx_spi_driver_data *sdd, 584 int timeout_ms) 585 { 586 void __iomem *regs = sdd->regs; 587 unsigned long val = 1; 588 u32 status; 589 590 /* max fifo depth available */ 591 u32 max_fifo = (FIFO_LVL_MASK(sdd) >> 1) + 1; 592 593 if (timeout_ms) 594 val = msecs_to_loops(timeout_ms); 595 596 do { 597 status = readl(regs + S3C64XX_SPI_STATUS); 598 } while (RX_FIFO_LVL(status, sdd) < max_fifo && --val); 599 600 /* return the actual received data length */ 601 return RX_FIFO_LVL(status, sdd); 602 } 603 604 static int wait_for_xfer(struct s3c64xx_spi_driver_data *sdd, 605 struct spi_transfer *xfer, int dma_mode) 606 { 607 void __iomem *regs = sdd->regs; 608 unsigned long val; 609 int ms; 610 611 /* millisecs to xfer 'len' bytes @ 'cur_speed' */ 612 ms = xfer->len * 8 * 1000 / sdd->cur_speed; 613 ms += 10; /* some tolerance */ 614 615 if (dma_mode) { 616 val = msecs_to_jiffies(ms) + 10; 617 val = wait_for_completion_timeout(&sdd->xfer_completion, val); 618 } else { 619 u32 status; 620 val = msecs_to_loops(ms); 621 do { 622 status = readl(regs + S3C64XX_SPI_STATUS); 623 } while (RX_FIFO_LVL(status, sdd) < xfer->len && --val); 624 } 625 626 if (dma_mode) { 627 u32 status; 628 629 /* 630 * If the previous xfer was completed within timeout, then 631 * proceed further else return -EIO. 632 * DmaTx returns after simply writing data in the FIFO, 633 * w/o waiting for real transmission on the bus to finish. 634 * DmaRx returns only after Dma read data from FIFO which 635 * needs bus transmission to finish, so we don't worry if 636 * Xfer involved Rx(with or without Tx). 637 */ 638 if (val && !xfer->rx_buf) { 639 val = msecs_to_loops(10); 640 status = readl(regs + S3C64XX_SPI_STATUS); 641 while ((TX_FIFO_LVL(status, sdd) 642 || !S3C64XX_SPI_ST_TX_DONE(status, sdd)) 643 && --val) { 644 cpu_relax(); 645 status = readl(regs + S3C64XX_SPI_STATUS); 646 } 647 648 } 649 650 /* If timed out while checking rx/tx status return error */ 651 if (!val) 652 return -EIO; 653 } else { 654 int loops; 655 u32 cpy_len; 656 u8 *buf; 657 658 /* If it was only Tx */ 659 if (!xfer->rx_buf) { 660 sdd->state &= ~TXBUSY; 661 return 0; 662 } 663 664 /* 665 * If the receive length is bigger than the controller fifo 666 * size, calculate the loops and read the fifo as many times. 667 * loops = length / max fifo size (calculated by using the 668 * fifo mask). 669 * For any size less than the fifo size the below code is 670 * executed atleast once. 671 */ 672 loops = xfer->len / ((FIFO_LVL_MASK(sdd) >> 1) + 1); 673 buf = xfer->rx_buf; 674 do { 675 /* wait for data to be received in the fifo */ 676 cpy_len = s3c64xx_spi_wait_for_timeout(sdd, 677 (loops ? ms : 0)); 678 679 switch (sdd->cur_bpw) { 680 case 32: 681 ioread32_rep(regs + S3C64XX_SPI_RX_DATA, 682 buf, cpy_len / 4); 683 break; 684 case 16: 685 ioread16_rep(regs + S3C64XX_SPI_RX_DATA, 686 buf, cpy_len / 2); 687 break; 688 default: 689 ioread8_rep(regs + S3C64XX_SPI_RX_DATA, 690 buf, cpy_len); 691 break; 692 } 693 694 buf = buf + cpy_len; 695 } while (loops--); 696 sdd->state &= ~RXBUSY; 697 } 698 699 return 0; 700 } 701 702 static inline void disable_cs(struct s3c64xx_spi_driver_data *sdd, 703 struct spi_device *spi) 704 { 705 struct s3c64xx_spi_csinfo *cs = spi->controller_data; 706 707 if (sdd->tgl_spi == spi) 708 sdd->tgl_spi = NULL; 709 710 if (sdd->cs_gpio) 711 gpio_set_value(cs->line, spi->mode & SPI_CS_HIGH ? 0 : 1); 712 713 /* Quiese the signals */ 714 writel(S3C64XX_SPI_SLAVE_SIG_INACT, sdd->regs + S3C64XX_SPI_SLAVE_SEL); 715 } 716 717 static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd) 718 { 719 void __iomem *regs = sdd->regs; 720 u32 val; 721 722 /* Disable Clock */ 723 if (sdd->port_conf->clk_from_cmu) { 724 clk_disable_unprepare(sdd->src_clk); 725 } else { 726 val = readl(regs + S3C64XX_SPI_CLK_CFG); 727 val &= ~S3C64XX_SPI_ENCLK_ENABLE; 728 writel(val, regs + S3C64XX_SPI_CLK_CFG); 729 } 730 731 /* Set Polarity and Phase */ 732 val = readl(regs + S3C64XX_SPI_CH_CFG); 733 val &= ~(S3C64XX_SPI_CH_SLAVE | 734 S3C64XX_SPI_CPOL_L | 735 S3C64XX_SPI_CPHA_B); 736 737 if (sdd->cur_mode & SPI_CPOL) 738 val |= S3C64XX_SPI_CPOL_L; 739 740 if (sdd->cur_mode & SPI_CPHA) 741 val |= S3C64XX_SPI_CPHA_B; 742 743 writel(val, regs + S3C64XX_SPI_CH_CFG); 744 745 /* Set Channel & DMA Mode */ 746 val = readl(regs + S3C64XX_SPI_MODE_CFG); 747 val &= ~(S3C64XX_SPI_MODE_BUS_TSZ_MASK 748 | S3C64XX_SPI_MODE_CH_TSZ_MASK); 749 750 switch (sdd->cur_bpw) { 751 case 32: 752 val |= S3C64XX_SPI_MODE_BUS_TSZ_WORD; 753 val |= S3C64XX_SPI_MODE_CH_TSZ_WORD; 754 break; 755 case 16: 756 val |= S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD; 757 val |= S3C64XX_SPI_MODE_CH_TSZ_HALFWORD; 758 break; 759 default: 760 val |= S3C64XX_SPI_MODE_BUS_TSZ_BYTE; 761 val |= S3C64XX_SPI_MODE_CH_TSZ_BYTE; 762 break; 763 } 764 765 writel(val, regs + S3C64XX_SPI_MODE_CFG); 766 767 if (sdd->port_conf->clk_from_cmu) { 768 /* Configure Clock */ 769 /* There is half-multiplier before the SPI */ 770 clk_set_rate(sdd->src_clk, sdd->cur_speed * 2); 771 /* Enable Clock */ 772 clk_prepare_enable(sdd->src_clk); 773 } else { 774 /* Configure Clock */ 775 val = readl(regs + S3C64XX_SPI_CLK_CFG); 776 val &= ~S3C64XX_SPI_PSR_MASK; 777 val |= ((clk_get_rate(sdd->src_clk) / sdd->cur_speed / 2 - 1) 778 & S3C64XX_SPI_PSR_MASK); 779 writel(val, regs + S3C64XX_SPI_CLK_CFG); 780 781 /* Enable Clock */ 782 val = readl(regs + S3C64XX_SPI_CLK_CFG); 783 val |= S3C64XX_SPI_ENCLK_ENABLE; 784 writel(val, regs + S3C64XX_SPI_CLK_CFG); 785 } 786 } 787 788 #define XFER_DMAADDR_INVALID DMA_BIT_MASK(32) 789 790 static int s3c64xx_spi_map_mssg(struct s3c64xx_spi_driver_data *sdd, 791 struct spi_message *msg) 792 { 793 struct device *dev = &sdd->pdev->dev; 794 struct spi_transfer *xfer; 795 796 if (is_polling(sdd) || msg->is_dma_mapped) 797 return 0; 798 799 /* First mark all xfer unmapped */ 800 list_for_each_entry(xfer, &msg->transfers, transfer_list) { 801 xfer->rx_dma = XFER_DMAADDR_INVALID; 802 xfer->tx_dma = XFER_DMAADDR_INVALID; 803 } 804 805 /* Map until end or first fail */ 806 list_for_each_entry(xfer, &msg->transfers, transfer_list) { 807 808 if (xfer->len <= ((FIFO_LVL_MASK(sdd) >> 1) + 1)) 809 continue; 810 811 if (xfer->tx_buf != NULL) { 812 xfer->tx_dma = dma_map_single(dev, 813 (void *)xfer->tx_buf, xfer->len, 814 DMA_TO_DEVICE); 815 if (dma_mapping_error(dev, xfer->tx_dma)) { 816 dev_err(dev, "dma_map_single Tx failed\n"); 817 xfer->tx_dma = XFER_DMAADDR_INVALID; 818 return -ENOMEM; 819 } 820 } 821 822 if (xfer->rx_buf != NULL) { 823 xfer->rx_dma = dma_map_single(dev, xfer->rx_buf, 824 xfer->len, DMA_FROM_DEVICE); 825 if (dma_mapping_error(dev, xfer->rx_dma)) { 826 dev_err(dev, "dma_map_single Rx failed\n"); 827 dma_unmap_single(dev, xfer->tx_dma, 828 xfer->len, DMA_TO_DEVICE); 829 xfer->tx_dma = XFER_DMAADDR_INVALID; 830 xfer->rx_dma = XFER_DMAADDR_INVALID; 831 return -ENOMEM; 832 } 833 } 834 } 835 836 return 0; 837 } 838 839 static void s3c64xx_spi_unmap_mssg(struct s3c64xx_spi_driver_data *sdd, 840 struct spi_message *msg) 841 { 842 struct device *dev = &sdd->pdev->dev; 843 struct spi_transfer *xfer; 844 845 if (is_polling(sdd) || msg->is_dma_mapped) 846 return; 847 848 list_for_each_entry(xfer, &msg->transfers, transfer_list) { 849 850 if (xfer->len <= ((FIFO_LVL_MASK(sdd) >> 1) + 1)) 851 continue; 852 853 if (xfer->rx_buf != NULL 854 && xfer->rx_dma != XFER_DMAADDR_INVALID) 855 dma_unmap_single(dev, xfer->rx_dma, 856 xfer->len, DMA_FROM_DEVICE); 857 858 if (xfer->tx_buf != NULL 859 && xfer->tx_dma != XFER_DMAADDR_INVALID) 860 dma_unmap_single(dev, xfer->tx_dma, 861 xfer->len, DMA_TO_DEVICE); 862 } 863 } 864 865 static int s3c64xx_spi_transfer_one_message(struct spi_master *master, 866 struct spi_message *msg) 867 { 868 struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master); 869 struct spi_device *spi = msg->spi; 870 struct s3c64xx_spi_csinfo *cs = spi->controller_data; 871 struct spi_transfer *xfer; 872 int status = 0, cs_toggle = 0; 873 u32 speed; 874 u8 bpw; 875 876 /* If Master's(controller) state differs from that needed by Slave */ 877 if (sdd->cur_speed != spi->max_speed_hz 878 || sdd->cur_mode != spi->mode 879 || sdd->cur_bpw != spi->bits_per_word) { 880 sdd->cur_bpw = spi->bits_per_word; 881 sdd->cur_speed = spi->max_speed_hz; 882 sdd->cur_mode = spi->mode; 883 s3c64xx_spi_config(sdd); 884 } 885 886 /* Map all the transfers if needed */ 887 if (s3c64xx_spi_map_mssg(sdd, msg)) { 888 dev_err(&spi->dev, 889 "Xfer: Unable to map message buffers!\n"); 890 status = -ENOMEM; 891 goto out; 892 } 893 894 /* Configure feedback delay */ 895 writel(cs->fb_delay & 0x3, sdd->regs + S3C64XX_SPI_FB_CLK); 896 897 list_for_each_entry(xfer, &msg->transfers, transfer_list) { 898 899 unsigned long flags; 900 int use_dma; 901 902 INIT_COMPLETION(sdd->xfer_completion); 903 904 /* Only BPW and Speed may change across transfers */ 905 bpw = xfer->bits_per_word; 906 speed = xfer->speed_hz ? : spi->max_speed_hz; 907 908 if (xfer->len % (bpw / 8)) { 909 dev_err(&spi->dev, 910 "Xfer length(%u) not a multiple of word size(%u)\n", 911 xfer->len, bpw / 8); 912 status = -EIO; 913 goto out; 914 } 915 916 if (bpw != sdd->cur_bpw || speed != sdd->cur_speed) { 917 sdd->cur_bpw = bpw; 918 sdd->cur_speed = speed; 919 s3c64xx_spi_config(sdd); 920 } 921 922 /* Polling method for xfers not bigger than FIFO capacity */ 923 use_dma = 0; 924 if (!is_polling(sdd) && 925 (sdd->rx_dma.ch && sdd->tx_dma.ch && 926 (xfer->len > ((FIFO_LVL_MASK(sdd) >> 1) + 1)))) 927 use_dma = 1; 928 929 spin_lock_irqsave(&sdd->lock, flags); 930 931 /* Pending only which is to be done */ 932 sdd->state &= ~RXBUSY; 933 sdd->state &= ~TXBUSY; 934 935 enable_datapath(sdd, spi, xfer, use_dma); 936 937 /* Slave Select */ 938 enable_cs(sdd, spi); 939 940 spin_unlock_irqrestore(&sdd->lock, flags); 941 942 status = wait_for_xfer(sdd, xfer, use_dma); 943 944 if (status) { 945 dev_err(&spi->dev, "I/O Error: rx-%d tx-%d res:rx-%c tx-%c len-%d\n", 946 xfer->rx_buf ? 1 : 0, xfer->tx_buf ? 1 : 0, 947 (sdd->state & RXBUSY) ? 'f' : 'p', 948 (sdd->state & TXBUSY) ? 'f' : 'p', 949 xfer->len); 950 951 if (use_dma) { 952 if (xfer->tx_buf != NULL 953 && (sdd->state & TXBUSY)) 954 s3c64xx_spi_dma_stop(sdd, &sdd->tx_dma); 955 if (xfer->rx_buf != NULL 956 && (sdd->state & RXBUSY)) 957 s3c64xx_spi_dma_stop(sdd, &sdd->rx_dma); 958 } 959 960 goto out; 961 } 962 963 if (xfer->delay_usecs) 964 udelay(xfer->delay_usecs); 965 966 if (xfer->cs_change) { 967 /* Hint that the next mssg is gonna be 968 for the same device */ 969 if (list_is_last(&xfer->transfer_list, 970 &msg->transfers)) 971 cs_toggle = 1; 972 } 973 974 msg->actual_length += xfer->len; 975 976 flush_fifo(sdd); 977 } 978 979 out: 980 if (!cs_toggle || status) 981 disable_cs(sdd, spi); 982 else 983 sdd->tgl_spi = spi; 984 985 s3c64xx_spi_unmap_mssg(sdd, msg); 986 987 msg->status = status; 988 989 spi_finalize_current_message(master); 990 991 return 0; 992 } 993 994 static struct s3c64xx_spi_csinfo *s3c64xx_get_slave_ctrldata( 995 struct spi_device *spi) 996 { 997 struct s3c64xx_spi_csinfo *cs; 998 struct device_node *slave_np, *data_np = NULL; 999 struct s3c64xx_spi_driver_data *sdd; 1000 u32 fb_delay = 0; 1001 1002 sdd = spi_master_get_devdata(spi->master); 1003 slave_np = spi->dev.of_node; 1004 if (!slave_np) { 1005 dev_err(&spi->dev, "device node not found\n"); 1006 return ERR_PTR(-EINVAL); 1007 } 1008 1009 data_np = of_get_child_by_name(slave_np, "controller-data"); 1010 if (!data_np) { 1011 dev_err(&spi->dev, "child node 'controller-data' not found\n"); 1012 return ERR_PTR(-EINVAL); 1013 } 1014 1015 cs = kzalloc(sizeof(*cs), GFP_KERNEL); 1016 if (!cs) { 1017 dev_err(&spi->dev, "could not allocate memory for controller data\n"); 1018 of_node_put(data_np); 1019 return ERR_PTR(-ENOMEM); 1020 } 1021 1022 /* The CS line is asserted/deasserted by the gpio pin */ 1023 if (sdd->cs_gpio) 1024 cs->line = of_get_named_gpio(data_np, "cs-gpio", 0); 1025 1026 if (!gpio_is_valid(cs->line)) { 1027 dev_err(&spi->dev, "chip select gpio is not specified or invalid\n"); 1028 kfree(cs); 1029 of_node_put(data_np); 1030 return ERR_PTR(-EINVAL); 1031 } 1032 1033 of_property_read_u32(data_np, "samsung,spi-feedback-delay", &fb_delay); 1034 cs->fb_delay = fb_delay; 1035 of_node_put(data_np); 1036 return cs; 1037 } 1038 1039 /* 1040 * Here we only check the validity of requested configuration 1041 * and save the configuration in a local data-structure. 1042 * The controller is actually configured only just before we 1043 * get a message to transfer. 1044 */ 1045 static int s3c64xx_spi_setup(struct spi_device *spi) 1046 { 1047 struct s3c64xx_spi_csinfo *cs = spi->controller_data; 1048 struct s3c64xx_spi_driver_data *sdd; 1049 struct s3c64xx_spi_info *sci; 1050 int err; 1051 1052 sdd = spi_master_get_devdata(spi->master); 1053 if (!cs && spi->dev.of_node) { 1054 cs = s3c64xx_get_slave_ctrldata(spi); 1055 spi->controller_data = cs; 1056 } 1057 1058 if (IS_ERR_OR_NULL(cs)) { 1059 dev_err(&spi->dev, "No CS for SPI(%d)\n", spi->chip_select); 1060 return -ENODEV; 1061 } 1062 1063 if (!spi_get_ctldata(spi)) { 1064 /* Request gpio only if cs line is asserted by gpio pins */ 1065 if (sdd->cs_gpio) { 1066 err = gpio_request_one(cs->line, GPIOF_OUT_INIT_HIGH, 1067 dev_name(&spi->dev)); 1068 if (err) { 1069 dev_err(&spi->dev, 1070 "Failed to get /CS gpio [%d]: %d\n", 1071 cs->line, err); 1072 goto err_gpio_req; 1073 } 1074 } 1075 1076 spi_set_ctldata(spi, cs); 1077 } 1078 1079 sci = sdd->cntrlr_info; 1080 1081 pm_runtime_get_sync(&sdd->pdev->dev); 1082 1083 /* Check if we can provide the requested rate */ 1084 if (!sdd->port_conf->clk_from_cmu) { 1085 u32 psr, speed; 1086 1087 /* Max possible */ 1088 speed = clk_get_rate(sdd->src_clk) / 2 / (0 + 1); 1089 1090 if (spi->max_speed_hz > speed) 1091 spi->max_speed_hz = speed; 1092 1093 psr = clk_get_rate(sdd->src_clk) / 2 / spi->max_speed_hz - 1; 1094 psr &= S3C64XX_SPI_PSR_MASK; 1095 if (psr == S3C64XX_SPI_PSR_MASK) 1096 psr--; 1097 1098 speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1); 1099 if (spi->max_speed_hz < speed) { 1100 if (psr+1 < S3C64XX_SPI_PSR_MASK) { 1101 psr++; 1102 } else { 1103 err = -EINVAL; 1104 goto setup_exit; 1105 } 1106 } 1107 1108 speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1); 1109 if (spi->max_speed_hz >= speed) { 1110 spi->max_speed_hz = speed; 1111 } else { 1112 dev_err(&spi->dev, "Can't set %dHz transfer speed\n", 1113 spi->max_speed_hz); 1114 err = -EINVAL; 1115 goto setup_exit; 1116 } 1117 } 1118 1119 pm_runtime_put(&sdd->pdev->dev); 1120 disable_cs(sdd, spi); 1121 return 0; 1122 1123 setup_exit: 1124 /* setup() returns with device de-selected */ 1125 disable_cs(sdd, spi); 1126 1127 gpio_free(cs->line); 1128 spi_set_ctldata(spi, NULL); 1129 1130 err_gpio_req: 1131 if (spi->dev.of_node) 1132 kfree(cs); 1133 1134 return err; 1135 } 1136 1137 static void s3c64xx_spi_cleanup(struct spi_device *spi) 1138 { 1139 struct s3c64xx_spi_csinfo *cs = spi_get_ctldata(spi); 1140 struct s3c64xx_spi_driver_data *sdd; 1141 1142 sdd = spi_master_get_devdata(spi->master); 1143 if (cs && sdd->cs_gpio) { 1144 gpio_free(cs->line); 1145 if (spi->dev.of_node) 1146 kfree(cs); 1147 } 1148 spi_set_ctldata(spi, NULL); 1149 } 1150 1151 static irqreturn_t s3c64xx_spi_irq(int irq, void *data) 1152 { 1153 struct s3c64xx_spi_driver_data *sdd = data; 1154 struct spi_master *spi = sdd->master; 1155 unsigned int val, clr = 0; 1156 1157 val = readl(sdd->regs + S3C64XX_SPI_STATUS); 1158 1159 if (val & S3C64XX_SPI_ST_RX_OVERRUN_ERR) { 1160 clr = S3C64XX_SPI_PND_RX_OVERRUN_CLR; 1161 dev_err(&spi->dev, "RX overrun\n"); 1162 } 1163 if (val & S3C64XX_SPI_ST_RX_UNDERRUN_ERR) { 1164 clr |= S3C64XX_SPI_PND_RX_UNDERRUN_CLR; 1165 dev_err(&spi->dev, "RX underrun\n"); 1166 } 1167 if (val & S3C64XX_SPI_ST_TX_OVERRUN_ERR) { 1168 clr |= S3C64XX_SPI_PND_TX_OVERRUN_CLR; 1169 dev_err(&spi->dev, "TX overrun\n"); 1170 } 1171 if (val & S3C64XX_SPI_ST_TX_UNDERRUN_ERR) { 1172 clr |= S3C64XX_SPI_PND_TX_UNDERRUN_CLR; 1173 dev_err(&spi->dev, "TX underrun\n"); 1174 } 1175 1176 /* Clear the pending irq by setting and then clearing it */ 1177 writel(clr, sdd->regs + S3C64XX_SPI_PENDING_CLR); 1178 writel(0, sdd->regs + S3C64XX_SPI_PENDING_CLR); 1179 1180 return IRQ_HANDLED; 1181 } 1182 1183 static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd, int channel) 1184 { 1185 struct s3c64xx_spi_info *sci = sdd->cntrlr_info; 1186 void __iomem *regs = sdd->regs; 1187 unsigned int val; 1188 1189 sdd->cur_speed = 0; 1190 1191 writel(S3C64XX_SPI_SLAVE_SIG_INACT, sdd->regs + S3C64XX_SPI_SLAVE_SEL); 1192 1193 /* Disable Interrupts - we use Polling if not DMA mode */ 1194 writel(0, regs + S3C64XX_SPI_INT_EN); 1195 1196 if (!sdd->port_conf->clk_from_cmu) 1197 writel(sci->src_clk_nr << S3C64XX_SPI_CLKSEL_SRCSHFT, 1198 regs + S3C64XX_SPI_CLK_CFG); 1199 writel(0, regs + S3C64XX_SPI_MODE_CFG); 1200 writel(0, regs + S3C64XX_SPI_PACKET_CNT); 1201 1202 /* Clear any irq pending bits, should set and clear the bits */ 1203 val = S3C64XX_SPI_PND_RX_OVERRUN_CLR | 1204 S3C64XX_SPI_PND_RX_UNDERRUN_CLR | 1205 S3C64XX_SPI_PND_TX_OVERRUN_CLR | 1206 S3C64XX_SPI_PND_TX_UNDERRUN_CLR; 1207 writel(val, regs + S3C64XX_SPI_PENDING_CLR); 1208 writel(0, regs + S3C64XX_SPI_PENDING_CLR); 1209 1210 writel(0, regs + S3C64XX_SPI_SWAP_CFG); 1211 1212 val = readl(regs + S3C64XX_SPI_MODE_CFG); 1213 val &= ~S3C64XX_SPI_MODE_4BURST; 1214 val &= ~(S3C64XX_SPI_MAX_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF); 1215 val |= (S3C64XX_SPI_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF); 1216 writel(val, regs + S3C64XX_SPI_MODE_CFG); 1217 1218 flush_fifo(sdd); 1219 } 1220 1221 #ifdef CONFIG_OF 1222 static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev) 1223 { 1224 struct s3c64xx_spi_info *sci; 1225 u32 temp; 1226 1227 sci = devm_kzalloc(dev, sizeof(*sci), GFP_KERNEL); 1228 if (!sci) { 1229 dev_err(dev, "memory allocation for spi_info failed\n"); 1230 return ERR_PTR(-ENOMEM); 1231 } 1232 1233 if (of_property_read_u32(dev->of_node, "samsung,spi-src-clk", &temp)) { 1234 dev_warn(dev, "spi bus clock parent not specified, using clock at index 0 as parent\n"); 1235 sci->src_clk_nr = 0; 1236 } else { 1237 sci->src_clk_nr = temp; 1238 } 1239 1240 if (of_property_read_u32(dev->of_node, "num-cs", &temp)) { 1241 dev_warn(dev, "number of chip select lines not specified, assuming 1 chip select line\n"); 1242 sci->num_cs = 1; 1243 } else { 1244 sci->num_cs = temp; 1245 } 1246 1247 return sci; 1248 } 1249 #else 1250 static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev) 1251 { 1252 return dev_get_platdata(dev); 1253 } 1254 #endif 1255 1256 static const struct of_device_id s3c64xx_spi_dt_match[]; 1257 1258 static inline struct s3c64xx_spi_port_config *s3c64xx_spi_get_port_config( 1259 struct platform_device *pdev) 1260 { 1261 #ifdef CONFIG_OF 1262 if (pdev->dev.of_node) { 1263 const struct of_device_id *match; 1264 match = of_match_node(s3c64xx_spi_dt_match, pdev->dev.of_node); 1265 return (struct s3c64xx_spi_port_config *)match->data; 1266 } 1267 #endif 1268 return (struct s3c64xx_spi_port_config *) 1269 platform_get_device_id(pdev)->driver_data; 1270 } 1271 1272 static int s3c64xx_spi_probe(struct platform_device *pdev) 1273 { 1274 struct resource *mem_res; 1275 struct resource *res; 1276 struct s3c64xx_spi_driver_data *sdd; 1277 struct s3c64xx_spi_info *sci = dev_get_platdata(&pdev->dev); 1278 struct spi_master *master; 1279 int ret, irq; 1280 char clk_name[16]; 1281 1282 if (!sci && pdev->dev.of_node) { 1283 sci = s3c64xx_spi_parse_dt(&pdev->dev); 1284 if (IS_ERR(sci)) 1285 return PTR_ERR(sci); 1286 } 1287 1288 if (!sci) { 1289 dev_err(&pdev->dev, "platform_data missing!\n"); 1290 return -ENODEV; 1291 } 1292 1293 mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1294 if (mem_res == NULL) { 1295 dev_err(&pdev->dev, "Unable to get SPI MEM resource\n"); 1296 return -ENXIO; 1297 } 1298 1299 irq = platform_get_irq(pdev, 0); 1300 if (irq < 0) { 1301 dev_warn(&pdev->dev, "Failed to get IRQ: %d\n", irq); 1302 return irq; 1303 } 1304 1305 master = spi_alloc_master(&pdev->dev, 1306 sizeof(struct s3c64xx_spi_driver_data)); 1307 if (master == NULL) { 1308 dev_err(&pdev->dev, "Unable to allocate SPI Master\n"); 1309 return -ENOMEM; 1310 } 1311 1312 platform_set_drvdata(pdev, master); 1313 1314 sdd = spi_master_get_devdata(master); 1315 sdd->port_conf = s3c64xx_spi_get_port_config(pdev); 1316 sdd->master = master; 1317 sdd->cntrlr_info = sci; 1318 sdd->pdev = pdev; 1319 sdd->sfr_start = mem_res->start; 1320 sdd->cs_gpio = true; 1321 if (pdev->dev.of_node) { 1322 if (!of_find_property(pdev->dev.of_node, "cs-gpio", NULL)) 1323 sdd->cs_gpio = false; 1324 1325 ret = of_alias_get_id(pdev->dev.of_node, "spi"); 1326 if (ret < 0) { 1327 dev_err(&pdev->dev, "failed to get alias id, errno %d\n", 1328 ret); 1329 goto err0; 1330 } 1331 sdd->port_id = ret; 1332 } else { 1333 sdd->port_id = pdev->id; 1334 } 1335 1336 sdd->cur_bpw = 8; 1337 1338 if (!sdd->pdev->dev.of_node) { 1339 res = platform_get_resource(pdev, IORESOURCE_DMA, 0); 1340 if (!res) { 1341 dev_warn(&pdev->dev, "Unable to get SPI tx dma resource. Switching to poll mode\n"); 1342 sdd->port_conf->quirks = S3C64XX_SPI_QUIRK_POLL; 1343 } else 1344 sdd->tx_dma.dmach = res->start; 1345 1346 res = platform_get_resource(pdev, IORESOURCE_DMA, 1); 1347 if (!res) { 1348 dev_warn(&pdev->dev, "Unable to get SPI rx dma resource. Switching to poll mode\n"); 1349 sdd->port_conf->quirks = S3C64XX_SPI_QUIRK_POLL; 1350 } else 1351 sdd->rx_dma.dmach = res->start; 1352 } 1353 1354 sdd->tx_dma.direction = DMA_MEM_TO_DEV; 1355 sdd->rx_dma.direction = DMA_DEV_TO_MEM; 1356 1357 master->dev.of_node = pdev->dev.of_node; 1358 master->bus_num = sdd->port_id; 1359 master->setup = s3c64xx_spi_setup; 1360 master->cleanup = s3c64xx_spi_cleanup; 1361 master->prepare_transfer_hardware = s3c64xx_spi_prepare_transfer; 1362 master->transfer_one_message = s3c64xx_spi_transfer_one_message; 1363 master->unprepare_transfer_hardware = s3c64xx_spi_unprepare_transfer; 1364 master->num_chipselect = sci->num_cs; 1365 master->dma_alignment = 8; 1366 master->bits_per_word_mask = SPI_BPW_MASK(32) | SPI_BPW_MASK(16) | 1367 SPI_BPW_MASK(8); 1368 /* the spi->mode bits understood by this driver: */ 1369 master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; 1370 master->auto_runtime_pm = true; 1371 1372 sdd->regs = devm_ioremap_resource(&pdev->dev, mem_res); 1373 if (IS_ERR(sdd->regs)) { 1374 ret = PTR_ERR(sdd->regs); 1375 goto err0; 1376 } 1377 1378 if (sci->cfg_gpio && sci->cfg_gpio()) { 1379 dev_err(&pdev->dev, "Unable to config gpio\n"); 1380 ret = -EBUSY; 1381 goto err0; 1382 } 1383 1384 /* Setup clocks */ 1385 sdd->clk = devm_clk_get(&pdev->dev, "spi"); 1386 if (IS_ERR(sdd->clk)) { 1387 dev_err(&pdev->dev, "Unable to acquire clock 'spi'\n"); 1388 ret = PTR_ERR(sdd->clk); 1389 goto err0; 1390 } 1391 1392 if (clk_prepare_enable(sdd->clk)) { 1393 dev_err(&pdev->dev, "Couldn't enable clock 'spi'\n"); 1394 ret = -EBUSY; 1395 goto err0; 1396 } 1397 1398 sprintf(clk_name, "spi_busclk%d", sci->src_clk_nr); 1399 sdd->src_clk = devm_clk_get(&pdev->dev, clk_name); 1400 if (IS_ERR(sdd->src_clk)) { 1401 dev_err(&pdev->dev, 1402 "Unable to acquire clock '%s'\n", clk_name); 1403 ret = PTR_ERR(sdd->src_clk); 1404 goto err2; 1405 } 1406 1407 if (clk_prepare_enable(sdd->src_clk)) { 1408 dev_err(&pdev->dev, "Couldn't enable clock '%s'\n", clk_name); 1409 ret = -EBUSY; 1410 goto err2; 1411 } 1412 1413 /* Setup Deufult Mode */ 1414 s3c64xx_spi_hwinit(sdd, sdd->port_id); 1415 1416 spin_lock_init(&sdd->lock); 1417 init_completion(&sdd->xfer_completion); 1418 1419 ret = devm_request_irq(&pdev->dev, irq, s3c64xx_spi_irq, 0, 1420 "spi-s3c64xx", sdd); 1421 if (ret != 0) { 1422 dev_err(&pdev->dev, "Failed to request IRQ %d: %d\n", 1423 irq, ret); 1424 goto err3; 1425 } 1426 1427 writel(S3C64XX_SPI_INT_RX_OVERRUN_EN | S3C64XX_SPI_INT_RX_UNDERRUN_EN | 1428 S3C64XX_SPI_INT_TX_OVERRUN_EN | S3C64XX_SPI_INT_TX_UNDERRUN_EN, 1429 sdd->regs + S3C64XX_SPI_INT_EN); 1430 1431 if (spi_register_master(master)) { 1432 dev_err(&pdev->dev, "cannot register SPI master\n"); 1433 ret = -EBUSY; 1434 goto err3; 1435 } 1436 1437 dev_dbg(&pdev->dev, "Samsung SoC SPI Driver loaded for Bus SPI-%d with %d Slaves attached\n", 1438 sdd->port_id, master->num_chipselect); 1439 dev_dbg(&pdev->dev, "\tIOmem=[%pR]\tDMA=[Rx-%d, Tx-%d]\n", 1440 mem_res, 1441 sdd->rx_dma.dmach, sdd->tx_dma.dmach); 1442 1443 pm_runtime_enable(&pdev->dev); 1444 1445 return 0; 1446 1447 err3: 1448 clk_disable_unprepare(sdd->src_clk); 1449 err2: 1450 clk_disable_unprepare(sdd->clk); 1451 err0: 1452 spi_master_put(master); 1453 1454 return ret; 1455 } 1456 1457 static int s3c64xx_spi_remove(struct platform_device *pdev) 1458 { 1459 struct spi_master *master = spi_master_get(platform_get_drvdata(pdev)); 1460 struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master); 1461 1462 pm_runtime_disable(&pdev->dev); 1463 1464 spi_unregister_master(master); 1465 1466 writel(0, sdd->regs + S3C64XX_SPI_INT_EN); 1467 1468 clk_disable_unprepare(sdd->src_clk); 1469 1470 clk_disable_unprepare(sdd->clk); 1471 1472 spi_master_put(master); 1473 1474 return 0; 1475 } 1476 1477 #ifdef CONFIG_PM_SLEEP 1478 static int s3c64xx_spi_suspend(struct device *dev) 1479 { 1480 struct spi_master *master = dev_get_drvdata(dev); 1481 struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master); 1482 1483 spi_master_suspend(master); 1484 1485 /* Disable the clock */ 1486 clk_disable_unprepare(sdd->src_clk); 1487 clk_disable_unprepare(sdd->clk); 1488 1489 sdd->cur_speed = 0; /* Output Clock is stopped */ 1490 1491 return 0; 1492 } 1493 1494 static int s3c64xx_spi_resume(struct device *dev) 1495 { 1496 struct spi_master *master = dev_get_drvdata(dev); 1497 struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master); 1498 struct s3c64xx_spi_info *sci = sdd->cntrlr_info; 1499 1500 if (sci->cfg_gpio) 1501 sci->cfg_gpio(); 1502 1503 /* Enable the clock */ 1504 clk_prepare_enable(sdd->src_clk); 1505 clk_prepare_enable(sdd->clk); 1506 1507 s3c64xx_spi_hwinit(sdd, sdd->port_id); 1508 1509 spi_master_resume(master); 1510 1511 return 0; 1512 } 1513 #endif /* CONFIG_PM_SLEEP */ 1514 1515 #ifdef CONFIG_PM_RUNTIME 1516 static int s3c64xx_spi_runtime_suspend(struct device *dev) 1517 { 1518 struct spi_master *master = dev_get_drvdata(dev); 1519 struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master); 1520 1521 clk_disable_unprepare(sdd->clk); 1522 clk_disable_unprepare(sdd->src_clk); 1523 1524 return 0; 1525 } 1526 1527 static int s3c64xx_spi_runtime_resume(struct device *dev) 1528 { 1529 struct spi_master *master = dev_get_drvdata(dev); 1530 struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master); 1531 1532 clk_prepare_enable(sdd->src_clk); 1533 clk_prepare_enable(sdd->clk); 1534 1535 return 0; 1536 } 1537 #endif /* CONFIG_PM_RUNTIME */ 1538 1539 static const struct dev_pm_ops s3c64xx_spi_pm = { 1540 SET_SYSTEM_SLEEP_PM_OPS(s3c64xx_spi_suspend, s3c64xx_spi_resume) 1541 SET_RUNTIME_PM_OPS(s3c64xx_spi_runtime_suspend, 1542 s3c64xx_spi_runtime_resume, NULL) 1543 }; 1544 1545 static struct s3c64xx_spi_port_config s3c2443_spi_port_config = { 1546 .fifo_lvl_mask = { 0x7f }, 1547 .rx_lvl_offset = 13, 1548 .tx_st_done = 21, 1549 .high_speed = true, 1550 }; 1551 1552 static struct s3c64xx_spi_port_config s3c6410_spi_port_config = { 1553 .fifo_lvl_mask = { 0x7f, 0x7F }, 1554 .rx_lvl_offset = 13, 1555 .tx_st_done = 21, 1556 }; 1557 1558 static struct s3c64xx_spi_port_config s5p64x0_spi_port_config = { 1559 .fifo_lvl_mask = { 0x1ff, 0x7F }, 1560 .rx_lvl_offset = 15, 1561 .tx_st_done = 25, 1562 }; 1563 1564 static struct s3c64xx_spi_port_config s5pc100_spi_port_config = { 1565 .fifo_lvl_mask = { 0x7f, 0x7F }, 1566 .rx_lvl_offset = 13, 1567 .tx_st_done = 21, 1568 .high_speed = true, 1569 }; 1570 1571 static struct s3c64xx_spi_port_config s5pv210_spi_port_config = { 1572 .fifo_lvl_mask = { 0x1ff, 0x7F }, 1573 .rx_lvl_offset = 15, 1574 .tx_st_done = 25, 1575 .high_speed = true, 1576 }; 1577 1578 static struct s3c64xx_spi_port_config exynos4_spi_port_config = { 1579 .fifo_lvl_mask = { 0x1ff, 0x7F, 0x7F }, 1580 .rx_lvl_offset = 15, 1581 .tx_st_done = 25, 1582 .high_speed = true, 1583 .clk_from_cmu = true, 1584 }; 1585 1586 static struct s3c64xx_spi_port_config exynos5440_spi_port_config = { 1587 .fifo_lvl_mask = { 0x1ff }, 1588 .rx_lvl_offset = 15, 1589 .tx_st_done = 25, 1590 .high_speed = true, 1591 .clk_from_cmu = true, 1592 .quirks = S3C64XX_SPI_QUIRK_POLL, 1593 }; 1594 1595 static struct platform_device_id s3c64xx_spi_driver_ids[] = { 1596 { 1597 .name = "s3c2443-spi", 1598 .driver_data = (kernel_ulong_t)&s3c2443_spi_port_config, 1599 }, { 1600 .name = "s3c6410-spi", 1601 .driver_data = (kernel_ulong_t)&s3c6410_spi_port_config, 1602 }, { 1603 .name = "s5p64x0-spi", 1604 .driver_data = (kernel_ulong_t)&s5p64x0_spi_port_config, 1605 }, { 1606 .name = "s5pc100-spi", 1607 .driver_data = (kernel_ulong_t)&s5pc100_spi_port_config, 1608 }, { 1609 .name = "s5pv210-spi", 1610 .driver_data = (kernel_ulong_t)&s5pv210_spi_port_config, 1611 }, { 1612 .name = "exynos4210-spi", 1613 .driver_data = (kernel_ulong_t)&exynos4_spi_port_config, 1614 }, 1615 { }, 1616 }; 1617 1618 static const struct of_device_id s3c64xx_spi_dt_match[] = { 1619 { .compatible = "samsung,exynos4210-spi", 1620 .data = (void *)&exynos4_spi_port_config, 1621 }, 1622 { .compatible = "samsung,exynos5440-spi", 1623 .data = (void *)&exynos5440_spi_port_config, 1624 }, 1625 { }, 1626 }; 1627 MODULE_DEVICE_TABLE(of, s3c64xx_spi_dt_match); 1628 1629 static struct platform_driver s3c64xx_spi_driver = { 1630 .driver = { 1631 .name = "s3c64xx-spi", 1632 .owner = THIS_MODULE, 1633 .pm = &s3c64xx_spi_pm, 1634 .of_match_table = of_match_ptr(s3c64xx_spi_dt_match), 1635 }, 1636 .remove = s3c64xx_spi_remove, 1637 .id_table = s3c64xx_spi_driver_ids, 1638 }; 1639 MODULE_ALIAS("platform:s3c64xx-spi"); 1640 1641 static int __init s3c64xx_spi_init(void) 1642 { 1643 return platform_driver_probe(&s3c64xx_spi_driver, s3c64xx_spi_probe); 1644 } 1645 subsys_initcall(s3c64xx_spi_init); 1646 1647 static void __exit s3c64xx_spi_exit(void) 1648 { 1649 platform_driver_unregister(&s3c64xx_spi_driver); 1650 } 1651 module_exit(s3c64xx_spi_exit); 1652 1653 MODULE_AUTHOR("Jaswinder Singh <jassi.brar@samsung.com>"); 1654 MODULE_DESCRIPTION("S3C64XX SPI Controller Driver"); 1655 MODULE_LICENSE("GPL"); 1656