1 // SPDX-License-Identifier: GPL-2.0 2 // Copyright (c) 2017-2018, The Linux foundation. All rights reserved. 3 4 #include <linux/clk.h> 5 #include <linux/interrupt.h> 6 #include <linux/io.h> 7 #include <linux/module.h> 8 #include <linux/of.h> 9 #include <linux/of_platform.h> 10 #include <linux/pm_runtime.h> 11 #include <linux/spi/spi.h> 12 #include <linux/spi/spi-mem.h> 13 14 15 #define QSPI_NUM_CS 2 16 #define QSPI_BYTES_PER_WORD 4 17 18 #define MSTR_CONFIG 0x0000 19 #define FULL_CYCLE_MODE BIT(3) 20 #define FB_CLK_EN BIT(4) 21 #define PIN_HOLDN BIT(6) 22 #define PIN_WPN BIT(7) 23 #define DMA_ENABLE BIT(8) 24 #define BIG_ENDIAN_MODE BIT(9) 25 #define SPI_MODE_MSK 0xc00 26 #define SPI_MODE_SHFT 10 27 #define CHIP_SELECT_NUM BIT(12) 28 #define SBL_EN BIT(13) 29 #define LPA_BASE_MSK 0x3c000 30 #define LPA_BASE_SHFT 14 31 #define TX_DATA_DELAY_MSK 0xc0000 32 #define TX_DATA_DELAY_SHFT 18 33 #define TX_CLK_DELAY_MSK 0x300000 34 #define TX_CLK_DELAY_SHFT 20 35 #define TX_CS_N_DELAY_MSK 0xc00000 36 #define TX_CS_N_DELAY_SHFT 22 37 #define TX_DATA_OE_DELAY_MSK 0x3000000 38 #define TX_DATA_OE_DELAY_SHFT 24 39 40 #define AHB_MASTER_CFG 0x0004 41 #define HMEM_TYPE_START_MID_TRANS_MSK 0x7 42 #define HMEM_TYPE_START_MID_TRANS_SHFT 0 43 #define HMEM_TYPE_LAST_TRANS_MSK 0x38 44 #define HMEM_TYPE_LAST_TRANS_SHFT 3 45 #define USE_HMEMTYPE_LAST_ON_DESC_OR_CHAIN_MSK 0xc0 46 #define USE_HMEMTYPE_LAST_ON_DESC_OR_CHAIN_SHFT 6 47 #define HMEMTYPE_READ_TRANS_MSK 0x700 48 #define HMEMTYPE_READ_TRANS_SHFT 8 49 #define HSHARED BIT(11) 50 #define HINNERSHARED BIT(12) 51 52 #define MSTR_INT_EN 0x000C 53 #define MSTR_INT_STATUS 0x0010 54 #define RESP_FIFO_UNDERRUN BIT(0) 55 #define RESP_FIFO_NOT_EMPTY BIT(1) 56 #define RESP_FIFO_RDY BIT(2) 57 #define HRESP_FROM_NOC_ERR BIT(3) 58 #define WR_FIFO_EMPTY BIT(9) 59 #define WR_FIFO_FULL BIT(10) 60 #define WR_FIFO_OVERRUN BIT(11) 61 #define TRANSACTION_DONE BIT(16) 62 #define QSPI_ERR_IRQS (RESP_FIFO_UNDERRUN | HRESP_FROM_NOC_ERR | \ 63 WR_FIFO_OVERRUN) 64 #define QSPI_ALL_IRQS (QSPI_ERR_IRQS | RESP_FIFO_RDY | \ 65 WR_FIFO_EMPTY | WR_FIFO_FULL | \ 66 TRANSACTION_DONE) 67 68 #define PIO_XFER_CTRL 0x0014 69 #define REQUEST_COUNT_MSK 0xffff 70 71 #define PIO_XFER_CFG 0x0018 72 #define TRANSFER_DIRECTION BIT(0) 73 #define MULTI_IO_MODE_MSK 0xe 74 #define MULTI_IO_MODE_SHFT 1 75 #define TRANSFER_FRAGMENT BIT(8) 76 #define SDR_1BIT 1 77 #define SDR_2BIT 2 78 #define SDR_4BIT 3 79 #define DDR_1BIT 5 80 #define DDR_2BIT 6 81 #define DDR_4BIT 7 82 #define DMA_DESC_SINGLE_SPI 1 83 #define DMA_DESC_DUAL_SPI 2 84 #define DMA_DESC_QUAD_SPI 3 85 86 #define PIO_XFER_STATUS 0x001c 87 #define WR_FIFO_BYTES_MSK 0xffff0000 88 #define WR_FIFO_BYTES_SHFT 16 89 90 #define PIO_DATAOUT_1B 0x0020 91 #define PIO_DATAOUT_4B 0x0024 92 93 #define RD_FIFO_CFG 0x0028 94 #define CONTINUOUS_MODE BIT(0) 95 96 #define RD_FIFO_STATUS 0x002c 97 #define FIFO_EMPTY BIT(11) 98 #define WR_CNTS_MSK 0x7f0 99 #define WR_CNTS_SHFT 4 100 #define RDY_64BYTE BIT(3) 101 #define RDY_32BYTE BIT(2) 102 #define RDY_16BYTE BIT(1) 103 #define FIFO_RDY BIT(0) 104 105 #define RD_FIFO_RESET 0x0030 106 #define RESET_FIFO BIT(0) 107 108 #define CUR_MEM_ADDR 0x0048 109 #define HW_VERSION 0x004c 110 #define RD_FIFO 0x0050 111 #define SAMPLING_CLK_CFG 0x0090 112 #define SAMPLING_CLK_STATUS 0x0094 113 114 115 enum qspi_dir { 116 QSPI_READ, 117 QSPI_WRITE, 118 }; 119 120 struct qspi_xfer { 121 union { 122 const void *tx_buf; 123 void *rx_buf; 124 }; 125 unsigned int rem_bytes; 126 unsigned int buswidth; 127 enum qspi_dir dir; 128 bool is_last; 129 }; 130 131 enum qspi_clocks { 132 QSPI_CLK_CORE, 133 QSPI_CLK_IFACE, 134 QSPI_NUM_CLKS 135 }; 136 137 struct qcom_qspi { 138 void __iomem *base; 139 struct device *dev; 140 struct clk_bulk_data clks[QSPI_NUM_CLKS]; 141 struct qspi_xfer xfer; 142 /* Lock to protect xfer and IRQ accessed registers */ 143 spinlock_t lock; 144 }; 145 146 static u32 qspi_buswidth_to_iomode(struct qcom_qspi *ctrl, 147 unsigned int buswidth) 148 { 149 switch (buswidth) { 150 case 1: 151 return SDR_1BIT << MULTI_IO_MODE_SHFT; 152 case 2: 153 return SDR_2BIT << MULTI_IO_MODE_SHFT; 154 case 4: 155 return SDR_4BIT << MULTI_IO_MODE_SHFT; 156 default: 157 dev_warn_once(ctrl->dev, 158 "Unexpected bus width: %u\n", buswidth); 159 return SDR_1BIT << MULTI_IO_MODE_SHFT; 160 } 161 } 162 163 static void qcom_qspi_pio_xfer_cfg(struct qcom_qspi *ctrl) 164 { 165 u32 pio_xfer_cfg; 166 const struct qspi_xfer *xfer; 167 168 xfer = &ctrl->xfer; 169 pio_xfer_cfg = readl(ctrl->base + PIO_XFER_CFG); 170 pio_xfer_cfg &= ~TRANSFER_DIRECTION; 171 pio_xfer_cfg |= xfer->dir; 172 if (xfer->is_last) 173 pio_xfer_cfg &= ~TRANSFER_FRAGMENT; 174 else 175 pio_xfer_cfg |= TRANSFER_FRAGMENT; 176 pio_xfer_cfg &= ~MULTI_IO_MODE_MSK; 177 pio_xfer_cfg |= qspi_buswidth_to_iomode(ctrl, xfer->buswidth); 178 179 writel(pio_xfer_cfg, ctrl->base + PIO_XFER_CFG); 180 } 181 182 static void qcom_qspi_pio_xfer_ctrl(struct qcom_qspi *ctrl) 183 { 184 u32 pio_xfer_ctrl; 185 186 pio_xfer_ctrl = readl(ctrl->base + PIO_XFER_CTRL); 187 pio_xfer_ctrl &= ~REQUEST_COUNT_MSK; 188 pio_xfer_ctrl |= ctrl->xfer.rem_bytes; 189 writel(pio_xfer_ctrl, ctrl->base + PIO_XFER_CTRL); 190 } 191 192 static void qcom_qspi_pio_xfer(struct qcom_qspi *ctrl) 193 { 194 u32 ints; 195 196 qcom_qspi_pio_xfer_cfg(ctrl); 197 198 /* Ack any previous interrupts that might be hanging around */ 199 writel(QSPI_ALL_IRQS, ctrl->base + MSTR_INT_STATUS); 200 201 /* Setup new interrupts */ 202 if (ctrl->xfer.dir == QSPI_WRITE) 203 ints = QSPI_ERR_IRQS | WR_FIFO_EMPTY; 204 else 205 ints = QSPI_ERR_IRQS | RESP_FIFO_RDY; 206 writel(ints, ctrl->base + MSTR_INT_EN); 207 208 /* Kick off the transfer */ 209 qcom_qspi_pio_xfer_ctrl(ctrl); 210 } 211 212 static void qcom_qspi_handle_err(struct spi_master *master, 213 struct spi_message *msg) 214 { 215 struct qcom_qspi *ctrl = spi_master_get_devdata(master); 216 unsigned long flags; 217 218 spin_lock_irqsave(&ctrl->lock, flags); 219 writel(0, ctrl->base + MSTR_INT_EN); 220 ctrl->xfer.rem_bytes = 0; 221 spin_unlock_irqrestore(&ctrl->lock, flags); 222 } 223 224 static int qcom_qspi_transfer_one(struct spi_master *master, 225 struct spi_device *slv, 226 struct spi_transfer *xfer) 227 { 228 struct qcom_qspi *ctrl = spi_master_get_devdata(master); 229 int ret; 230 unsigned long speed_hz; 231 unsigned long flags; 232 233 speed_hz = slv->max_speed_hz; 234 if (xfer->speed_hz) 235 speed_hz = xfer->speed_hz; 236 237 /* In regular operation (SBL_EN=1) core must be 4x transfer clock */ 238 ret = clk_set_rate(ctrl->clks[QSPI_CLK_CORE].clk, speed_hz * 4); 239 if (ret) { 240 dev_err(ctrl->dev, "Failed to set core clk %d\n", ret); 241 return ret; 242 } 243 244 spin_lock_irqsave(&ctrl->lock, flags); 245 246 /* We are half duplex, so either rx or tx will be set */ 247 if (xfer->rx_buf) { 248 ctrl->xfer.dir = QSPI_READ; 249 ctrl->xfer.buswidth = xfer->rx_nbits; 250 ctrl->xfer.rx_buf = xfer->rx_buf; 251 } else { 252 ctrl->xfer.dir = QSPI_WRITE; 253 ctrl->xfer.buswidth = xfer->tx_nbits; 254 ctrl->xfer.tx_buf = xfer->tx_buf; 255 } 256 ctrl->xfer.is_last = list_is_last(&xfer->transfer_list, 257 &master->cur_msg->transfers); 258 ctrl->xfer.rem_bytes = xfer->len; 259 qcom_qspi_pio_xfer(ctrl); 260 261 spin_unlock_irqrestore(&ctrl->lock, flags); 262 263 /* We'll call spi_finalize_current_transfer() when done */ 264 return 1; 265 } 266 267 static int qcom_qspi_prepare_message(struct spi_master *master, 268 struct spi_message *message) 269 { 270 u32 mstr_cfg; 271 struct qcom_qspi *ctrl; 272 int tx_data_oe_delay = 1; 273 int tx_data_delay = 1; 274 unsigned long flags; 275 276 ctrl = spi_master_get_devdata(master); 277 spin_lock_irqsave(&ctrl->lock, flags); 278 279 mstr_cfg = readl(ctrl->base + MSTR_CONFIG); 280 mstr_cfg &= ~CHIP_SELECT_NUM; 281 if (message->spi->chip_select) 282 mstr_cfg |= CHIP_SELECT_NUM; 283 284 mstr_cfg |= FB_CLK_EN | PIN_WPN | PIN_HOLDN | SBL_EN | FULL_CYCLE_MODE; 285 mstr_cfg &= ~(SPI_MODE_MSK | TX_DATA_OE_DELAY_MSK | TX_DATA_DELAY_MSK); 286 mstr_cfg |= message->spi->mode << SPI_MODE_SHFT; 287 mstr_cfg |= tx_data_oe_delay << TX_DATA_OE_DELAY_SHFT; 288 mstr_cfg |= tx_data_delay << TX_DATA_DELAY_SHFT; 289 mstr_cfg &= ~DMA_ENABLE; 290 291 writel(mstr_cfg, ctrl->base + MSTR_CONFIG); 292 spin_unlock_irqrestore(&ctrl->lock, flags); 293 294 return 0; 295 } 296 297 static irqreturn_t pio_read(struct qcom_qspi *ctrl) 298 { 299 u32 rd_fifo_status; 300 u32 rd_fifo; 301 unsigned int wr_cnts; 302 unsigned int bytes_to_read; 303 unsigned int words_to_read; 304 u32 *word_buf; 305 u8 *byte_buf; 306 int i; 307 308 rd_fifo_status = readl(ctrl->base + RD_FIFO_STATUS); 309 310 if (!(rd_fifo_status & FIFO_RDY)) { 311 dev_dbg(ctrl->dev, "Spurious IRQ %#x\n", rd_fifo_status); 312 return IRQ_NONE; 313 } 314 315 wr_cnts = (rd_fifo_status & WR_CNTS_MSK) >> WR_CNTS_SHFT; 316 wr_cnts = min(wr_cnts, ctrl->xfer.rem_bytes); 317 318 words_to_read = wr_cnts / QSPI_BYTES_PER_WORD; 319 bytes_to_read = wr_cnts % QSPI_BYTES_PER_WORD; 320 321 if (words_to_read) { 322 word_buf = ctrl->xfer.rx_buf; 323 ctrl->xfer.rem_bytes -= words_to_read * QSPI_BYTES_PER_WORD; 324 ioread32_rep(ctrl->base + RD_FIFO, word_buf, words_to_read); 325 ctrl->xfer.rx_buf = word_buf + words_to_read; 326 } 327 328 if (bytes_to_read) { 329 byte_buf = ctrl->xfer.rx_buf; 330 rd_fifo = readl(ctrl->base + RD_FIFO); 331 ctrl->xfer.rem_bytes -= bytes_to_read; 332 for (i = 0; i < bytes_to_read; i++) 333 *byte_buf++ = rd_fifo >> (i * BITS_PER_BYTE); 334 ctrl->xfer.rx_buf = byte_buf; 335 } 336 337 return IRQ_HANDLED; 338 } 339 340 static irqreturn_t pio_write(struct qcom_qspi *ctrl) 341 { 342 const void *xfer_buf = ctrl->xfer.tx_buf; 343 const int *word_buf; 344 const char *byte_buf; 345 unsigned int wr_fifo_bytes; 346 unsigned int wr_fifo_words; 347 unsigned int wr_size; 348 unsigned int rem_words; 349 350 wr_fifo_bytes = readl(ctrl->base + PIO_XFER_STATUS); 351 wr_fifo_bytes >>= WR_FIFO_BYTES_SHFT; 352 353 if (ctrl->xfer.rem_bytes < QSPI_BYTES_PER_WORD) { 354 /* Process the last 1-3 bytes */ 355 wr_size = min(wr_fifo_bytes, ctrl->xfer.rem_bytes); 356 ctrl->xfer.rem_bytes -= wr_size; 357 358 byte_buf = xfer_buf; 359 while (wr_size--) 360 writel(*byte_buf++, 361 ctrl->base + PIO_DATAOUT_1B); 362 ctrl->xfer.tx_buf = byte_buf; 363 } else { 364 /* 365 * Process all the whole words; to keep things simple we'll 366 * just wait for the next interrupt to handle the last 1-3 367 * bytes if we don't have an even number of words. 368 */ 369 rem_words = ctrl->xfer.rem_bytes / QSPI_BYTES_PER_WORD; 370 wr_fifo_words = wr_fifo_bytes / QSPI_BYTES_PER_WORD; 371 372 wr_size = min(rem_words, wr_fifo_words); 373 ctrl->xfer.rem_bytes -= wr_size * QSPI_BYTES_PER_WORD; 374 375 word_buf = xfer_buf; 376 iowrite32_rep(ctrl->base + PIO_DATAOUT_4B, word_buf, wr_size); 377 ctrl->xfer.tx_buf = word_buf + wr_size; 378 379 } 380 381 return IRQ_HANDLED; 382 } 383 384 static irqreturn_t qcom_qspi_irq(int irq, void *dev_id) 385 { 386 u32 int_status; 387 struct qcom_qspi *ctrl = dev_id; 388 irqreturn_t ret = IRQ_NONE; 389 unsigned long flags; 390 391 spin_lock_irqsave(&ctrl->lock, flags); 392 393 int_status = readl(ctrl->base + MSTR_INT_STATUS); 394 writel(int_status, ctrl->base + MSTR_INT_STATUS); 395 396 if (ctrl->xfer.dir == QSPI_WRITE) { 397 if (int_status & WR_FIFO_EMPTY) 398 ret = pio_write(ctrl); 399 } else { 400 if (int_status & RESP_FIFO_RDY) 401 ret = pio_read(ctrl); 402 } 403 404 if (int_status & QSPI_ERR_IRQS) { 405 if (int_status & RESP_FIFO_UNDERRUN) 406 dev_err(ctrl->dev, "IRQ error: FIFO underrun\n"); 407 if (int_status & WR_FIFO_OVERRUN) 408 dev_err(ctrl->dev, "IRQ error: FIFO overrun\n"); 409 if (int_status & HRESP_FROM_NOC_ERR) 410 dev_err(ctrl->dev, "IRQ error: NOC response error\n"); 411 ret = IRQ_HANDLED; 412 } 413 414 if (!ctrl->xfer.rem_bytes) { 415 writel(0, ctrl->base + MSTR_INT_EN); 416 spi_finalize_current_transfer(dev_get_drvdata(ctrl->dev)); 417 } 418 419 spin_unlock_irqrestore(&ctrl->lock, flags); 420 return ret; 421 } 422 423 static int qcom_qspi_probe(struct platform_device *pdev) 424 { 425 int ret; 426 struct device *dev; 427 struct resource *res; 428 struct spi_master *master; 429 struct qcom_qspi *ctrl; 430 431 dev = &pdev->dev; 432 433 master = spi_alloc_master(dev, sizeof(*ctrl)); 434 if (!master) 435 return -ENOMEM; 436 437 platform_set_drvdata(pdev, master); 438 439 ctrl = spi_master_get_devdata(master); 440 441 spin_lock_init(&ctrl->lock); 442 ctrl->dev = dev; 443 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 444 ctrl->base = devm_ioremap_resource(dev, res); 445 if (IS_ERR(ctrl->base)) { 446 ret = PTR_ERR(ctrl->base); 447 goto exit_probe_master_put; 448 } 449 450 ctrl->clks[QSPI_CLK_CORE].id = "core"; 451 ctrl->clks[QSPI_CLK_IFACE].id = "iface"; 452 ret = devm_clk_bulk_get(dev, QSPI_NUM_CLKS, ctrl->clks); 453 if (ret) 454 goto exit_probe_master_put; 455 456 ret = platform_get_irq(pdev, 0); 457 if (ret < 0) { 458 dev_err(dev, "Failed to get irq %d\n", ret); 459 goto exit_probe_master_put; 460 } 461 ret = devm_request_irq(dev, ret, qcom_qspi_irq, 462 IRQF_TRIGGER_HIGH, dev_name(dev), ctrl); 463 if (ret) { 464 dev_err(dev, "Failed to request irq %d\n", ret); 465 goto exit_probe_master_put; 466 } 467 468 master->max_speed_hz = 300000000; 469 master->num_chipselect = QSPI_NUM_CS; 470 master->bus_num = -1; 471 master->dev.of_node = pdev->dev.of_node; 472 master->mode_bits = SPI_MODE_0 | 473 SPI_TX_DUAL | SPI_RX_DUAL | 474 SPI_TX_QUAD | SPI_RX_QUAD; 475 master->flags = SPI_MASTER_HALF_DUPLEX; 476 master->prepare_message = qcom_qspi_prepare_message; 477 master->transfer_one = qcom_qspi_transfer_one; 478 master->handle_err = qcom_qspi_handle_err; 479 master->auto_runtime_pm = true; 480 481 pm_runtime_enable(dev); 482 483 ret = spi_register_master(master); 484 if (!ret) 485 return 0; 486 487 pm_runtime_disable(dev); 488 489 exit_probe_master_put: 490 spi_master_put(master); 491 492 return ret; 493 } 494 495 static int qcom_qspi_remove(struct platform_device *pdev) 496 { 497 struct spi_master *master = platform_get_drvdata(pdev); 498 499 /* Unregister _before_ disabling pm_runtime() so we stop transfers */ 500 spi_unregister_master(master); 501 502 pm_runtime_disable(&pdev->dev); 503 504 return 0; 505 } 506 507 static int __maybe_unused qcom_qspi_runtime_suspend(struct device *dev) 508 { 509 struct spi_master *master = dev_get_drvdata(dev); 510 struct qcom_qspi *ctrl = spi_master_get_devdata(master); 511 512 clk_bulk_disable_unprepare(QSPI_NUM_CLKS, ctrl->clks); 513 514 return 0; 515 } 516 517 static int __maybe_unused qcom_qspi_runtime_resume(struct device *dev) 518 { 519 struct spi_master *master = dev_get_drvdata(dev); 520 struct qcom_qspi *ctrl = spi_master_get_devdata(master); 521 522 return clk_bulk_prepare_enable(QSPI_NUM_CLKS, ctrl->clks); 523 } 524 525 static int __maybe_unused qcom_qspi_suspend(struct device *dev) 526 { 527 struct spi_master *master = dev_get_drvdata(dev); 528 int ret; 529 530 ret = spi_master_suspend(master); 531 if (ret) 532 return ret; 533 534 ret = pm_runtime_force_suspend(dev); 535 if (ret) 536 spi_master_resume(master); 537 538 return ret; 539 } 540 541 static int __maybe_unused qcom_qspi_resume(struct device *dev) 542 { 543 struct spi_master *master = dev_get_drvdata(dev); 544 int ret; 545 546 ret = pm_runtime_force_resume(dev); 547 if (ret) 548 return ret; 549 550 ret = spi_master_resume(master); 551 if (ret) 552 pm_runtime_force_suspend(dev); 553 554 return ret; 555 } 556 557 static const struct dev_pm_ops qcom_qspi_dev_pm_ops = { 558 SET_RUNTIME_PM_OPS(qcom_qspi_runtime_suspend, 559 qcom_qspi_runtime_resume, NULL) 560 SET_SYSTEM_SLEEP_PM_OPS(qcom_qspi_suspend, qcom_qspi_resume) 561 }; 562 563 static const struct of_device_id qcom_qspi_dt_match[] = { 564 { .compatible = "qcom,qspi-v1", }, 565 { } 566 }; 567 MODULE_DEVICE_TABLE(of, qcom_qspi_dt_match); 568 569 static struct platform_driver qcom_qspi_driver = { 570 .driver = { 571 .name = "qcom_qspi", 572 .pm = &qcom_qspi_dev_pm_ops, 573 .of_match_table = qcom_qspi_dt_match, 574 }, 575 .probe = qcom_qspi_probe, 576 .remove = qcom_qspi_remove, 577 }; 578 module_platform_driver(qcom_qspi_driver); 579 580 MODULE_DESCRIPTION("SPI driver for QSPI cores"); 581 MODULE_LICENSE("GPL v2"); 582