1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * SPI_PPC4XX SPI controller driver. 4 * 5 * Copyright (C) 2007 Gary Jennejohn <garyj@denx.de> 6 * Copyright 2008 Stefan Roese <sr@denx.de>, DENX Software Engineering 7 * Copyright 2009 Harris Corporation, Steven A. Falco <sfalco@harris.com> 8 * 9 * Based in part on drivers/spi/spi_s3c24xx.c 10 * 11 * Copyright (c) 2006 Ben Dooks 12 * Copyright (c) 2006 Simtec Electronics 13 * Ben Dooks <ben@simtec.co.uk> 14 */ 15 16 /* 17 * The PPC4xx SPI controller has no FIFO so each sent/received byte will 18 * generate an interrupt to the CPU. This can cause high CPU utilization. 19 * This driver allows platforms to reduce the interrupt load on the CPU 20 * during SPI transfers by setting max_speed_hz via the device tree. 21 */ 22 23 #include <linux/module.h> 24 #include <linux/sched.h> 25 #include <linux/slab.h> 26 #include <linux/errno.h> 27 #include <linux/wait.h> 28 #include <linux/of_address.h> 29 #include <linux/of_irq.h> 30 #include <linux/of_platform.h> 31 #include <linux/interrupt.h> 32 #include <linux/delay.h> 33 34 #include <linux/spi/spi.h> 35 #include <linux/spi/spi_bitbang.h> 36 37 #include <linux/io.h> 38 #include <asm/dcr.h> 39 #include <asm/dcr-regs.h> 40 41 /* bits in mode register - bit 0 is MSb */ 42 43 /* 44 * SPI_PPC4XX_MODE_SCP = 0 means "data latched on trailing edge of clock" 45 * SPI_PPC4XX_MODE_SCP = 1 means "data latched on leading edge of clock" 46 * Note: This is the inverse of CPHA. 47 */ 48 #define SPI_PPC4XX_MODE_SCP (0x80 >> 3) 49 50 /* SPI_PPC4XX_MODE_SPE = 1 means "port enabled" */ 51 #define SPI_PPC4XX_MODE_SPE (0x80 >> 4) 52 53 /* 54 * SPI_PPC4XX_MODE_RD = 0 means "MSB first" - this is the normal mode 55 * SPI_PPC4XX_MODE_RD = 1 means "LSB first" - this is bit-reversed mode 56 * Note: This is identical to SPI_LSB_FIRST. 57 */ 58 #define SPI_PPC4XX_MODE_RD (0x80 >> 5) 59 60 /* 61 * SPI_PPC4XX_MODE_CI = 0 means "clock idles low" 62 * SPI_PPC4XX_MODE_CI = 1 means "clock idles high" 63 * Note: This is identical to CPOL. 64 */ 65 #define SPI_PPC4XX_MODE_CI (0x80 >> 6) 66 67 /* 68 * SPI_PPC4XX_MODE_IL = 0 means "loopback disable" 69 * SPI_PPC4XX_MODE_IL = 1 means "loopback enable" 70 */ 71 #define SPI_PPC4XX_MODE_IL (0x80 >> 7) 72 73 /* bits in control register */ 74 /* starts a transfer when set */ 75 #define SPI_PPC4XX_CR_STR (0x80 >> 7) 76 77 /* bits in status register */ 78 /* port is busy with a transfer */ 79 #define SPI_PPC4XX_SR_BSY (0x80 >> 6) 80 /* RxD ready */ 81 #define SPI_PPC4XX_SR_RBR (0x80 >> 7) 82 83 /* clock settings (SCP and CI) for various SPI modes */ 84 #define SPI_CLK_MODE0 (SPI_PPC4XX_MODE_SCP | 0) 85 #define SPI_CLK_MODE1 (0 | 0) 86 #define SPI_CLK_MODE2 (SPI_PPC4XX_MODE_SCP | SPI_PPC4XX_MODE_CI) 87 #define SPI_CLK_MODE3 (0 | SPI_PPC4XX_MODE_CI) 88 89 #define DRIVER_NAME "spi_ppc4xx_of" 90 91 struct spi_ppc4xx_regs { 92 u8 mode; 93 u8 rxd; 94 u8 txd; 95 u8 cr; 96 u8 sr; 97 u8 dummy; 98 /* 99 * Clock divisor modulus register 100 * This uses the following formula: 101 * SCPClkOut = OPBCLK/(4(CDM + 1)) 102 * or 103 * CDM = (OPBCLK/4*SCPClkOut) - 1 104 * bit 0 is the MSb! 105 */ 106 u8 cdm; 107 }; 108 109 /* SPI Controller driver's private data. */ 110 struct ppc4xx_spi { 111 /* bitbang has to be first */ 112 struct spi_bitbang bitbang; 113 struct completion done; 114 115 u64 mapbase; 116 u64 mapsize; 117 int irqnum; 118 /* need this to set the SPI clock */ 119 unsigned int opb_freq; 120 121 /* for transfers */ 122 int len; 123 int count; 124 /* data buffers */ 125 const unsigned char *tx; 126 unsigned char *rx; 127 128 struct spi_ppc4xx_regs __iomem *regs; /* pointer to the registers */ 129 struct spi_controller *host; 130 struct device *dev; 131 }; 132 133 /* need this so we can set the clock in the chipselect routine */ 134 struct spi_ppc4xx_cs { 135 u8 mode; 136 }; 137 138 static int spi_ppc4xx_txrx(struct spi_device *spi, struct spi_transfer *t) 139 { 140 struct ppc4xx_spi *hw; 141 u8 data; 142 143 dev_dbg(&spi->dev, "txrx: tx %p, rx %p, len %d\n", 144 t->tx_buf, t->rx_buf, t->len); 145 146 hw = spi_controller_get_devdata(spi->controller); 147 148 hw->tx = t->tx_buf; 149 hw->rx = t->rx_buf; 150 hw->len = t->len; 151 hw->count = 0; 152 153 /* send the first byte */ 154 data = hw->tx ? hw->tx[0] : 0; 155 out_8(&hw->regs->txd, data); 156 out_8(&hw->regs->cr, SPI_PPC4XX_CR_STR); 157 wait_for_completion(&hw->done); 158 159 return hw->count; 160 } 161 162 static int spi_ppc4xx_setupxfer(struct spi_device *spi, struct spi_transfer *t) 163 { 164 struct ppc4xx_spi *hw = spi_controller_get_devdata(spi->controller); 165 struct spi_ppc4xx_cs *cs = spi->controller_state; 166 int scr; 167 u8 cdm = 0; 168 u32 speed; 169 170 /* Start with the generic configuration for this device. */ 171 speed = spi->max_speed_hz; 172 173 /* 174 * Modify the configuration if the transfer overrides it. Do not allow 175 * the transfer to overwrite the generic configuration with zeros. 176 */ 177 if (t) { 178 if (t->speed_hz) 179 speed = min(t->speed_hz, spi->max_speed_hz); 180 } 181 182 if (!speed || (speed > spi->max_speed_hz)) { 183 dev_err(&spi->dev, "invalid speed_hz (%d)\n", speed); 184 return -EINVAL; 185 } 186 187 /* Write new configuration */ 188 out_8(&hw->regs->mode, cs->mode); 189 190 /* Set the clock */ 191 /* opb_freq was already divided by 4 */ 192 scr = (hw->opb_freq / speed) - 1; 193 if (scr > 0) 194 cdm = min(scr, 0xff); 195 196 dev_dbg(&spi->dev, "setting pre-scaler to %d (hz %d)\n", cdm, speed); 197 198 if (in_8(&hw->regs->cdm) != cdm) 199 out_8(&hw->regs->cdm, cdm); 200 201 mutex_lock(&hw->bitbang.lock); 202 if (!hw->bitbang.busy) { 203 hw->bitbang.chipselect(spi, BITBANG_CS_INACTIVE); 204 /* Need to ndelay here? */ 205 } 206 mutex_unlock(&hw->bitbang.lock); 207 208 return 0; 209 } 210 211 static int spi_ppc4xx_setup(struct spi_device *spi) 212 { 213 struct spi_ppc4xx_cs *cs = spi->controller_state; 214 215 if (!spi->max_speed_hz) { 216 dev_err(&spi->dev, "invalid max_speed_hz (must be non-zero)\n"); 217 return -EINVAL; 218 } 219 220 if (cs == NULL) { 221 cs = kzalloc(sizeof(*cs), GFP_KERNEL); 222 if (!cs) 223 return -ENOMEM; 224 spi->controller_state = cs; 225 } 226 227 /* 228 * We set all bits of the SPI0_MODE register, so, 229 * no need to read-modify-write 230 */ 231 cs->mode = SPI_PPC4XX_MODE_SPE; 232 233 switch (spi->mode & SPI_MODE_X_MASK) { 234 case SPI_MODE_0: 235 cs->mode |= SPI_CLK_MODE0; 236 break; 237 case SPI_MODE_1: 238 cs->mode |= SPI_CLK_MODE1; 239 break; 240 case SPI_MODE_2: 241 cs->mode |= SPI_CLK_MODE2; 242 break; 243 case SPI_MODE_3: 244 cs->mode |= SPI_CLK_MODE3; 245 break; 246 } 247 248 if (spi->mode & SPI_LSB_FIRST) 249 cs->mode |= SPI_PPC4XX_MODE_RD; 250 251 return 0; 252 } 253 254 static irqreturn_t spi_ppc4xx_int(int irq, void *dev_id) 255 { 256 struct ppc4xx_spi *hw; 257 u8 status; 258 u8 data; 259 unsigned int count; 260 261 hw = (struct ppc4xx_spi *)dev_id; 262 263 status = in_8(&hw->regs->sr); 264 if (!status) 265 return IRQ_NONE; 266 267 /* 268 * BSY de-asserts one cycle after the transfer is complete. The 269 * interrupt is asserted after the transfer is complete. The exact 270 * relationship is not documented, hence this code. 271 */ 272 273 if (unlikely(status & SPI_PPC4XX_SR_BSY)) { 274 u8 lstatus; 275 int cnt = 0; 276 277 dev_dbg(hw->dev, "got interrupt but spi still busy?\n"); 278 do { 279 ndelay(10); 280 lstatus = in_8(&hw->regs->sr); 281 } while (++cnt < 100 && lstatus & SPI_PPC4XX_SR_BSY); 282 283 if (cnt >= 100) { 284 dev_err(hw->dev, "busywait: too many loops!\n"); 285 complete(&hw->done); 286 return IRQ_HANDLED; 287 } else { 288 /* status is always 1 (RBR) here */ 289 status = in_8(&hw->regs->sr); 290 dev_dbg(hw->dev, "loops %d status %x\n", cnt, status); 291 } 292 } 293 294 count = hw->count; 295 hw->count++; 296 297 /* RBR triggered this interrupt. Therefore, data must be ready. */ 298 data = in_8(&hw->regs->rxd); 299 if (hw->rx) 300 hw->rx[count] = data; 301 302 count++; 303 304 if (count < hw->len) { 305 data = hw->tx ? hw->tx[count] : 0; 306 out_8(&hw->regs->txd, data); 307 out_8(&hw->regs->cr, SPI_PPC4XX_CR_STR); 308 } else { 309 complete(&hw->done); 310 } 311 312 return IRQ_HANDLED; 313 } 314 315 static void spi_ppc4xx_cleanup(struct spi_device *spi) 316 { 317 kfree(spi->controller_state); 318 } 319 320 static void spi_ppc4xx_enable(struct ppc4xx_spi *hw) 321 { 322 /* 323 * On all 4xx PPC's the SPI bus is shared/multiplexed with 324 * the 2nd I2C bus. We need to enable the SPI bus before 325 * using it. 326 */ 327 328 /* need to clear bit 14 to enable SPC */ 329 dcri_clrset(SDR0, SDR0_PFC1, 0x80000000 >> 14, 0); 330 } 331 332 /* 333 * platform_device layer stuff... 334 */ 335 static int spi_ppc4xx_of_probe(struct platform_device *op) 336 { 337 struct ppc4xx_spi *hw; 338 struct spi_controller *host; 339 struct spi_bitbang *bbp; 340 struct resource resource; 341 struct device_node *np = op->dev.of_node; 342 struct device *dev = &op->dev; 343 struct device_node *opbnp; 344 int ret; 345 const unsigned int *clk; 346 347 host = spi_alloc_host(dev, sizeof(*hw)); 348 if (host == NULL) 349 return -ENOMEM; 350 host->dev.of_node = np; 351 platform_set_drvdata(op, host); 352 hw = spi_controller_get_devdata(host); 353 hw->host = host; 354 hw->dev = dev; 355 356 init_completion(&hw->done); 357 358 /* Setup the state for the bitbang driver */ 359 bbp = &hw->bitbang; 360 bbp->master = hw->host; 361 bbp->setup_transfer = spi_ppc4xx_setupxfer; 362 bbp->txrx_bufs = spi_ppc4xx_txrx; 363 bbp->use_dma = 0; 364 bbp->master->setup = spi_ppc4xx_setup; 365 bbp->master->cleanup = spi_ppc4xx_cleanup; 366 bbp->master->bits_per_word_mask = SPI_BPW_MASK(8); 367 bbp->master->use_gpio_descriptors = true; 368 /* 369 * The SPI core will count the number of GPIO descriptors to figure 370 * out the number of chip selects available on the platform. 371 */ 372 bbp->master->num_chipselect = 0; 373 374 /* the spi->mode bits understood by this driver: */ 375 bbp->master->mode_bits = 376 SPI_CPHA | SPI_CPOL | SPI_CS_HIGH | SPI_LSB_FIRST; 377 378 /* Get the clock for the OPB */ 379 opbnp = of_find_compatible_node(NULL, NULL, "ibm,opb"); 380 if (opbnp == NULL) { 381 dev_err(dev, "OPB: cannot find node\n"); 382 ret = -ENODEV; 383 goto free_host; 384 } 385 /* Get the clock (Hz) for the OPB */ 386 clk = of_get_property(opbnp, "clock-frequency", NULL); 387 if (clk == NULL) { 388 dev_err(dev, "OPB: no clock-frequency property set\n"); 389 of_node_put(opbnp); 390 ret = -ENODEV; 391 goto free_host; 392 } 393 hw->opb_freq = *clk; 394 hw->opb_freq >>= 2; 395 of_node_put(opbnp); 396 397 ret = of_address_to_resource(np, 0, &resource); 398 if (ret) { 399 dev_err(dev, "error while parsing device node resource\n"); 400 goto free_host; 401 } 402 hw->mapbase = resource.start; 403 hw->mapsize = resource_size(&resource); 404 405 /* Sanity check */ 406 if (hw->mapsize < sizeof(struct spi_ppc4xx_regs)) { 407 dev_err(dev, "too small to map registers\n"); 408 ret = -EINVAL; 409 goto free_host; 410 } 411 412 /* Request IRQ */ 413 hw->irqnum = irq_of_parse_and_map(np, 0); 414 if (hw->irqnum <= 0) 415 goto free_host; 416 417 ret = request_irq(hw->irqnum, spi_ppc4xx_int, 418 0, "spi_ppc4xx_of", (void *)hw); 419 if (ret) { 420 dev_err(dev, "unable to allocate interrupt\n"); 421 goto free_host; 422 } 423 424 if (!request_mem_region(hw->mapbase, hw->mapsize, DRIVER_NAME)) { 425 dev_err(dev, "resource unavailable\n"); 426 ret = -EBUSY; 427 goto request_mem_error; 428 } 429 430 hw->regs = ioremap(hw->mapbase, sizeof(struct spi_ppc4xx_regs)); 431 432 if (!hw->regs) { 433 dev_err(dev, "unable to memory map registers\n"); 434 ret = -ENXIO; 435 goto map_io_error; 436 } 437 438 spi_ppc4xx_enable(hw); 439 440 /* Finally register our spi controller */ 441 dev->dma_mask = 0; 442 ret = spi_bitbang_start(bbp); 443 if (ret) { 444 dev_err(dev, "failed to register SPI host\n"); 445 goto unmap_regs; 446 } 447 448 dev_info(dev, "driver initialized\n"); 449 450 return 0; 451 452 unmap_regs: 453 iounmap(hw->regs); 454 map_io_error: 455 release_mem_region(hw->mapbase, hw->mapsize); 456 request_mem_error: 457 free_irq(hw->irqnum, hw); 458 free_host: 459 spi_controller_put(host); 460 461 dev_err(dev, "initialization failed\n"); 462 return ret; 463 } 464 465 static void spi_ppc4xx_of_remove(struct platform_device *op) 466 { 467 struct spi_controller *host = platform_get_drvdata(op); 468 struct ppc4xx_spi *hw = spi_controller_get_devdata(host); 469 470 spi_bitbang_stop(&hw->bitbang); 471 release_mem_region(hw->mapbase, hw->mapsize); 472 free_irq(hw->irqnum, hw); 473 iounmap(hw->regs); 474 spi_controller_put(host); 475 } 476 477 static const struct of_device_id spi_ppc4xx_of_match[] = { 478 { .compatible = "ibm,ppc4xx-spi", }, 479 {}, 480 }; 481 482 MODULE_DEVICE_TABLE(of, spi_ppc4xx_of_match); 483 484 static struct platform_driver spi_ppc4xx_of_driver = { 485 .probe = spi_ppc4xx_of_probe, 486 .remove_new = spi_ppc4xx_of_remove, 487 .driver = { 488 .name = DRIVER_NAME, 489 .of_match_table = spi_ppc4xx_of_match, 490 }, 491 }; 492 module_platform_driver(spi_ppc4xx_of_driver); 493 494 MODULE_AUTHOR("Gary Jennejohn & Stefan Roese"); 495 MODULE_DESCRIPTION("Simple PPC4xx SPI Driver"); 496 MODULE_LICENSE("GPL"); 497