1 /* 2 * A driver for the ARM PL022 PrimeCell SSP/SPI bus master. 3 * 4 * Copyright (C) 2008-2012 ST-Ericsson AB 5 * Copyright (C) 2006 STMicroelectronics Pvt. Ltd. 6 * 7 * Author: Linus Walleij <linus.walleij@stericsson.com> 8 * 9 * Initial version inspired by: 10 * linux-2.6.17-rc3-mm1/drivers/spi/pxa2xx_spi.c 11 * Initial adoption to PL022 by: 12 * Sachin Verma <sachin.verma@st.com> 13 * 14 * This program is free software; you can redistribute it and/or modify 15 * it under the terms of the GNU General Public License as published by 16 * the Free Software Foundation; either version 2 of the License, or 17 * (at your option) any later version. 18 * 19 * This program is distributed in the hope that it will be useful, 20 * but WITHOUT ANY WARRANTY; without even the implied warranty of 21 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 22 * GNU General Public License for more details. 23 */ 24 25 #include <linux/init.h> 26 #include <linux/module.h> 27 #include <linux/device.h> 28 #include <linux/ioport.h> 29 #include <linux/errno.h> 30 #include <linux/interrupt.h> 31 #include <linux/spi/spi.h> 32 #include <linux/delay.h> 33 #include <linux/clk.h> 34 #include <linux/err.h> 35 #include <linux/amba/bus.h> 36 #include <linux/amba/pl022.h> 37 #include <linux/io.h> 38 #include <linux/slab.h> 39 #include <linux/dmaengine.h> 40 #include <linux/dma-mapping.h> 41 #include <linux/scatterlist.h> 42 #include <linux/pm_runtime.h> 43 #include <linux/gpio.h> 44 #include <linux/of_gpio.h> 45 #include <linux/pinctrl/consumer.h> 46 47 /* 48 * This macro is used to define some register default values. 49 * reg is masked with mask, the OR:ed with an (again masked) 50 * val shifted sb steps to the left. 51 */ 52 #define SSP_WRITE_BITS(reg, val, mask, sb) \ 53 ((reg) = (((reg) & ~(mask)) | (((val)<<(sb)) & (mask)))) 54 55 /* 56 * This macro is also used to define some default values. 57 * It will just shift val by sb steps to the left and mask 58 * the result with mask. 59 */ 60 #define GEN_MASK_BITS(val, mask, sb) \ 61 (((val)<<(sb)) & (mask)) 62 63 #define DRIVE_TX 0 64 #define DO_NOT_DRIVE_TX 1 65 66 #define DO_NOT_QUEUE_DMA 0 67 #define QUEUE_DMA 1 68 69 #define RX_TRANSFER 1 70 #define TX_TRANSFER 2 71 72 /* 73 * Macros to access SSP Registers with their offsets 74 */ 75 #define SSP_CR0(r) (r + 0x000) 76 #define SSP_CR1(r) (r + 0x004) 77 #define SSP_DR(r) (r + 0x008) 78 #define SSP_SR(r) (r + 0x00C) 79 #define SSP_CPSR(r) (r + 0x010) 80 #define SSP_IMSC(r) (r + 0x014) 81 #define SSP_RIS(r) (r + 0x018) 82 #define SSP_MIS(r) (r + 0x01C) 83 #define SSP_ICR(r) (r + 0x020) 84 #define SSP_DMACR(r) (r + 0x024) 85 #define SSP_CSR(r) (r + 0x030) /* vendor extension */ 86 #define SSP_ITCR(r) (r + 0x080) 87 #define SSP_ITIP(r) (r + 0x084) 88 #define SSP_ITOP(r) (r + 0x088) 89 #define SSP_TDR(r) (r + 0x08C) 90 91 #define SSP_PID0(r) (r + 0xFE0) 92 #define SSP_PID1(r) (r + 0xFE4) 93 #define SSP_PID2(r) (r + 0xFE8) 94 #define SSP_PID3(r) (r + 0xFEC) 95 96 #define SSP_CID0(r) (r + 0xFF0) 97 #define SSP_CID1(r) (r + 0xFF4) 98 #define SSP_CID2(r) (r + 0xFF8) 99 #define SSP_CID3(r) (r + 0xFFC) 100 101 /* 102 * SSP Control Register 0 - SSP_CR0 103 */ 104 #define SSP_CR0_MASK_DSS (0x0FUL << 0) 105 #define SSP_CR0_MASK_FRF (0x3UL << 4) 106 #define SSP_CR0_MASK_SPO (0x1UL << 6) 107 #define SSP_CR0_MASK_SPH (0x1UL << 7) 108 #define SSP_CR0_MASK_SCR (0xFFUL << 8) 109 110 /* 111 * The ST version of this block moves som bits 112 * in SSP_CR0 and extends it to 32 bits 113 */ 114 #define SSP_CR0_MASK_DSS_ST (0x1FUL << 0) 115 #define SSP_CR0_MASK_HALFDUP_ST (0x1UL << 5) 116 #define SSP_CR0_MASK_CSS_ST (0x1FUL << 16) 117 #define SSP_CR0_MASK_FRF_ST (0x3UL << 21) 118 119 /* 120 * SSP Control Register 0 - SSP_CR1 121 */ 122 #define SSP_CR1_MASK_LBM (0x1UL << 0) 123 #define SSP_CR1_MASK_SSE (0x1UL << 1) 124 #define SSP_CR1_MASK_MS (0x1UL << 2) 125 #define SSP_CR1_MASK_SOD (0x1UL << 3) 126 127 /* 128 * The ST version of this block adds some bits 129 * in SSP_CR1 130 */ 131 #define SSP_CR1_MASK_RENDN_ST (0x1UL << 4) 132 #define SSP_CR1_MASK_TENDN_ST (0x1UL << 5) 133 #define SSP_CR1_MASK_MWAIT_ST (0x1UL << 6) 134 #define SSP_CR1_MASK_RXIFLSEL_ST (0x7UL << 7) 135 #define SSP_CR1_MASK_TXIFLSEL_ST (0x7UL << 10) 136 /* This one is only in the PL023 variant */ 137 #define SSP_CR1_MASK_FBCLKDEL_ST (0x7UL << 13) 138 139 /* 140 * SSP Status Register - SSP_SR 141 */ 142 #define SSP_SR_MASK_TFE (0x1UL << 0) /* Transmit FIFO empty */ 143 #define SSP_SR_MASK_TNF (0x1UL << 1) /* Transmit FIFO not full */ 144 #define SSP_SR_MASK_RNE (0x1UL << 2) /* Receive FIFO not empty */ 145 #define SSP_SR_MASK_RFF (0x1UL << 3) /* Receive FIFO full */ 146 #define SSP_SR_MASK_BSY (0x1UL << 4) /* Busy Flag */ 147 148 /* 149 * SSP Clock Prescale Register - SSP_CPSR 150 */ 151 #define SSP_CPSR_MASK_CPSDVSR (0xFFUL << 0) 152 153 /* 154 * SSP Interrupt Mask Set/Clear Register - SSP_IMSC 155 */ 156 #define SSP_IMSC_MASK_RORIM (0x1UL << 0) /* Receive Overrun Interrupt mask */ 157 #define SSP_IMSC_MASK_RTIM (0x1UL << 1) /* Receive timeout Interrupt mask */ 158 #define SSP_IMSC_MASK_RXIM (0x1UL << 2) /* Receive FIFO Interrupt mask */ 159 #define SSP_IMSC_MASK_TXIM (0x1UL << 3) /* Transmit FIFO Interrupt mask */ 160 161 /* 162 * SSP Raw Interrupt Status Register - SSP_RIS 163 */ 164 /* Receive Overrun Raw Interrupt status */ 165 #define SSP_RIS_MASK_RORRIS (0x1UL << 0) 166 /* Receive Timeout Raw Interrupt status */ 167 #define SSP_RIS_MASK_RTRIS (0x1UL << 1) 168 /* Receive FIFO Raw Interrupt status */ 169 #define SSP_RIS_MASK_RXRIS (0x1UL << 2) 170 /* Transmit FIFO Raw Interrupt status */ 171 #define SSP_RIS_MASK_TXRIS (0x1UL << 3) 172 173 /* 174 * SSP Masked Interrupt Status Register - SSP_MIS 175 */ 176 /* Receive Overrun Masked Interrupt status */ 177 #define SSP_MIS_MASK_RORMIS (0x1UL << 0) 178 /* Receive Timeout Masked Interrupt status */ 179 #define SSP_MIS_MASK_RTMIS (0x1UL << 1) 180 /* Receive FIFO Masked Interrupt status */ 181 #define SSP_MIS_MASK_RXMIS (0x1UL << 2) 182 /* Transmit FIFO Masked Interrupt status */ 183 #define SSP_MIS_MASK_TXMIS (0x1UL << 3) 184 185 /* 186 * SSP Interrupt Clear Register - SSP_ICR 187 */ 188 /* Receive Overrun Raw Clear Interrupt bit */ 189 #define SSP_ICR_MASK_RORIC (0x1UL << 0) 190 /* Receive Timeout Clear Interrupt bit */ 191 #define SSP_ICR_MASK_RTIC (0x1UL << 1) 192 193 /* 194 * SSP DMA Control Register - SSP_DMACR 195 */ 196 /* Receive DMA Enable bit */ 197 #define SSP_DMACR_MASK_RXDMAE (0x1UL << 0) 198 /* Transmit DMA Enable bit */ 199 #define SSP_DMACR_MASK_TXDMAE (0x1UL << 1) 200 201 /* 202 * SSP Chip Select Control Register - SSP_CSR 203 * (vendor extension) 204 */ 205 #define SSP_CSR_CSVALUE_MASK (0x1FUL << 0) 206 207 /* 208 * SSP Integration Test control Register - SSP_ITCR 209 */ 210 #define SSP_ITCR_MASK_ITEN (0x1UL << 0) 211 #define SSP_ITCR_MASK_TESTFIFO (0x1UL << 1) 212 213 /* 214 * SSP Integration Test Input Register - SSP_ITIP 215 */ 216 #define ITIP_MASK_SSPRXD (0x1UL << 0) 217 #define ITIP_MASK_SSPFSSIN (0x1UL << 1) 218 #define ITIP_MASK_SSPCLKIN (0x1UL << 2) 219 #define ITIP_MASK_RXDMAC (0x1UL << 3) 220 #define ITIP_MASK_TXDMAC (0x1UL << 4) 221 #define ITIP_MASK_SSPTXDIN (0x1UL << 5) 222 223 /* 224 * SSP Integration Test output Register - SSP_ITOP 225 */ 226 #define ITOP_MASK_SSPTXD (0x1UL << 0) 227 #define ITOP_MASK_SSPFSSOUT (0x1UL << 1) 228 #define ITOP_MASK_SSPCLKOUT (0x1UL << 2) 229 #define ITOP_MASK_SSPOEn (0x1UL << 3) 230 #define ITOP_MASK_SSPCTLOEn (0x1UL << 4) 231 #define ITOP_MASK_RORINTR (0x1UL << 5) 232 #define ITOP_MASK_RTINTR (0x1UL << 6) 233 #define ITOP_MASK_RXINTR (0x1UL << 7) 234 #define ITOP_MASK_TXINTR (0x1UL << 8) 235 #define ITOP_MASK_INTR (0x1UL << 9) 236 #define ITOP_MASK_RXDMABREQ (0x1UL << 10) 237 #define ITOP_MASK_RXDMASREQ (0x1UL << 11) 238 #define ITOP_MASK_TXDMABREQ (0x1UL << 12) 239 #define ITOP_MASK_TXDMASREQ (0x1UL << 13) 240 241 /* 242 * SSP Test Data Register - SSP_TDR 243 */ 244 #define TDR_MASK_TESTDATA (0xFFFFFFFF) 245 246 /* 247 * Message State 248 * we use the spi_message.state (void *) pointer to 249 * hold a single state value, that's why all this 250 * (void *) casting is done here. 251 */ 252 #define STATE_START ((void *) 0) 253 #define STATE_RUNNING ((void *) 1) 254 #define STATE_DONE ((void *) 2) 255 #define STATE_ERROR ((void *) -1) 256 257 /* 258 * SSP State - Whether Enabled or Disabled 259 */ 260 #define SSP_DISABLED (0) 261 #define SSP_ENABLED (1) 262 263 /* 264 * SSP DMA State - Whether DMA Enabled or Disabled 265 */ 266 #define SSP_DMA_DISABLED (0) 267 #define SSP_DMA_ENABLED (1) 268 269 /* 270 * SSP Clock Defaults 271 */ 272 #define SSP_DEFAULT_CLKRATE 0x2 273 #define SSP_DEFAULT_PRESCALE 0x40 274 275 /* 276 * SSP Clock Parameter ranges 277 */ 278 #define CPSDVR_MIN 0x02 279 #define CPSDVR_MAX 0xFE 280 #define SCR_MIN 0x00 281 #define SCR_MAX 0xFF 282 283 /* 284 * SSP Interrupt related Macros 285 */ 286 #define DEFAULT_SSP_REG_IMSC 0x0UL 287 #define DISABLE_ALL_INTERRUPTS DEFAULT_SSP_REG_IMSC 288 #define ENABLE_ALL_INTERRUPTS ( \ 289 SSP_IMSC_MASK_RORIM | \ 290 SSP_IMSC_MASK_RTIM | \ 291 SSP_IMSC_MASK_RXIM | \ 292 SSP_IMSC_MASK_TXIM \ 293 ) 294 295 #define CLEAR_ALL_INTERRUPTS 0x3 296 297 #define SPI_POLLING_TIMEOUT 1000 298 299 /* 300 * The type of reading going on on this chip 301 */ 302 enum ssp_reading { 303 READING_NULL, 304 READING_U8, 305 READING_U16, 306 READING_U32 307 }; 308 309 /** 310 * The type of writing going on on this chip 311 */ 312 enum ssp_writing { 313 WRITING_NULL, 314 WRITING_U8, 315 WRITING_U16, 316 WRITING_U32 317 }; 318 319 /** 320 * struct vendor_data - vendor-specific config parameters 321 * for PL022 derivates 322 * @fifodepth: depth of FIFOs (both) 323 * @max_bpw: maximum number of bits per word 324 * @unidir: supports unidirection transfers 325 * @extended_cr: 32 bit wide control register 0 with extra 326 * features and extra features in CR1 as found in the ST variants 327 * @pl023: supports a subset of the ST extensions called "PL023" 328 * @internal_cs_ctrl: supports chip select control register 329 */ 330 struct vendor_data { 331 int fifodepth; 332 int max_bpw; 333 bool unidir; 334 bool extended_cr; 335 bool pl023; 336 bool loopback; 337 bool internal_cs_ctrl; 338 }; 339 340 /** 341 * struct pl022 - This is the private SSP driver data structure 342 * @adev: AMBA device model hookup 343 * @vendor: vendor data for the IP block 344 * @phybase: the physical memory where the SSP device resides 345 * @virtbase: the virtual memory where the SSP is mapped 346 * @clk: outgoing clock "SPICLK" for the SPI bus 347 * @master: SPI framework hookup 348 * @master_info: controller-specific data from machine setup 349 * @kworker: thread struct for message pump 350 * @kworker_task: pointer to task for message pump kworker thread 351 * @pump_messages: work struct for scheduling work to the message pump 352 * @queue_lock: spinlock to syncronise access to message queue 353 * @queue: message queue 354 * @busy: message pump is busy 355 * @running: message pump is running 356 * @pump_transfers: Tasklet used in Interrupt Transfer mode 357 * @cur_msg: Pointer to current spi_message being processed 358 * @cur_transfer: Pointer to current spi_transfer 359 * @cur_chip: pointer to current clients chip(assigned from controller_state) 360 * @next_msg_cs_active: the next message in the queue has been examined 361 * and it was found that it uses the same chip select as the previous 362 * message, so we left it active after the previous transfer, and it's 363 * active already. 364 * @tx: current position in TX buffer to be read 365 * @tx_end: end position in TX buffer to be read 366 * @rx: current position in RX buffer to be written 367 * @rx_end: end position in RX buffer to be written 368 * @read: the type of read currently going on 369 * @write: the type of write currently going on 370 * @exp_fifo_level: expected FIFO level 371 * @dma_rx_channel: optional channel for RX DMA 372 * @dma_tx_channel: optional channel for TX DMA 373 * @sgt_rx: scattertable for the RX transfer 374 * @sgt_tx: scattertable for the TX transfer 375 * @dummypage: a dummy page used for driving data on the bus with DMA 376 * @cur_cs: current chip select (gpio) 377 * @chipselects: list of chipselects (gpios) 378 */ 379 struct pl022 { 380 struct amba_device *adev; 381 struct vendor_data *vendor; 382 resource_size_t phybase; 383 void __iomem *virtbase; 384 struct clk *clk; 385 struct spi_master *master; 386 struct pl022_ssp_controller *master_info; 387 /* Message per-transfer pump */ 388 struct tasklet_struct pump_transfers; 389 struct spi_message *cur_msg; 390 struct spi_transfer *cur_transfer; 391 struct chip_data *cur_chip; 392 bool next_msg_cs_active; 393 void *tx; 394 void *tx_end; 395 void *rx; 396 void *rx_end; 397 enum ssp_reading read; 398 enum ssp_writing write; 399 u32 exp_fifo_level; 400 enum ssp_rx_level_trig rx_lev_trig; 401 enum ssp_tx_level_trig tx_lev_trig; 402 /* DMA settings */ 403 #ifdef CONFIG_DMA_ENGINE 404 struct dma_chan *dma_rx_channel; 405 struct dma_chan *dma_tx_channel; 406 struct sg_table sgt_rx; 407 struct sg_table sgt_tx; 408 char *dummypage; 409 bool dma_running; 410 #endif 411 int cur_cs; 412 int *chipselects; 413 }; 414 415 /** 416 * struct chip_data - To maintain runtime state of SSP for each client chip 417 * @cr0: Value of control register CR0 of SSP - on later ST variants this 418 * register is 32 bits wide rather than just 16 419 * @cr1: Value of control register CR1 of SSP 420 * @dmacr: Value of DMA control Register of SSP 421 * @cpsr: Value of Clock prescale register 422 * @n_bytes: how many bytes(power of 2) reqd for a given data width of client 423 * @enable_dma: Whether to enable DMA or not 424 * @read: function ptr to be used to read when doing xfer for this chip 425 * @write: function ptr to be used to write when doing xfer for this chip 426 * @cs_control: chip select callback provided by chip 427 * @xfer_type: polling/interrupt/DMA 428 * 429 * Runtime state of the SSP controller, maintained per chip, 430 * This would be set according to the current message that would be served 431 */ 432 struct chip_data { 433 u32 cr0; 434 u16 cr1; 435 u16 dmacr; 436 u16 cpsr; 437 u8 n_bytes; 438 bool enable_dma; 439 enum ssp_reading read; 440 enum ssp_writing write; 441 void (*cs_control) (u32 command); 442 int xfer_type; 443 }; 444 445 /** 446 * null_cs_control - Dummy chip select function 447 * @command: select/delect the chip 448 * 449 * If no chip select function is provided by client this is used as dummy 450 * chip select 451 */ 452 static void null_cs_control(u32 command) 453 { 454 pr_debug("pl022: dummy chip select control, CS=0x%x\n", command); 455 } 456 457 /** 458 * internal_cs_control - Control chip select signals via SSP_CSR. 459 * @pl022: SSP driver private data structure 460 * @command: select/delect the chip 461 * 462 * Used on controller with internal chip select control via SSP_CSR register 463 * (vendor extension). Each of the 5 LSB in the register controls one chip 464 * select signal. 465 */ 466 static void internal_cs_control(struct pl022 *pl022, u32 command) 467 { 468 u32 tmp; 469 470 tmp = readw(SSP_CSR(pl022->virtbase)); 471 if (command == SSP_CHIP_SELECT) 472 tmp &= ~BIT(pl022->cur_cs); 473 else 474 tmp |= BIT(pl022->cur_cs); 475 writew(tmp, SSP_CSR(pl022->virtbase)); 476 } 477 478 static void pl022_cs_control(struct pl022 *pl022, u32 command) 479 { 480 if (pl022->vendor->internal_cs_ctrl) 481 internal_cs_control(pl022, command); 482 else if (gpio_is_valid(pl022->cur_cs)) 483 gpio_set_value(pl022->cur_cs, command); 484 else 485 pl022->cur_chip->cs_control(command); 486 } 487 488 /** 489 * giveback - current spi_message is over, schedule next message and call 490 * callback of this message. Assumes that caller already 491 * set message->status; dma and pio irqs are blocked 492 * @pl022: SSP driver private data structure 493 */ 494 static void giveback(struct pl022 *pl022) 495 { 496 struct spi_transfer *last_transfer; 497 pl022->next_msg_cs_active = false; 498 499 last_transfer = list_last_entry(&pl022->cur_msg->transfers, 500 struct spi_transfer, transfer_list); 501 502 /* Delay if requested before any change in chip select */ 503 if (last_transfer->delay_usecs) 504 /* 505 * FIXME: This runs in interrupt context. 506 * Is this really smart? 507 */ 508 udelay(last_transfer->delay_usecs); 509 510 if (!last_transfer->cs_change) { 511 struct spi_message *next_msg; 512 513 /* 514 * cs_change was not set. We can keep the chip select 515 * enabled if there is message in the queue and it is 516 * for the same spi device. 517 * 518 * We cannot postpone this until pump_messages, because 519 * after calling msg->complete (below) the driver that 520 * sent the current message could be unloaded, which 521 * could invalidate the cs_control() callback... 522 */ 523 /* get a pointer to the next message, if any */ 524 next_msg = spi_get_next_queued_message(pl022->master); 525 526 /* 527 * see if the next and current messages point 528 * to the same spi device. 529 */ 530 if (next_msg && next_msg->spi != pl022->cur_msg->spi) 531 next_msg = NULL; 532 if (!next_msg || pl022->cur_msg->state == STATE_ERROR) 533 pl022_cs_control(pl022, SSP_CHIP_DESELECT); 534 else 535 pl022->next_msg_cs_active = true; 536 537 } 538 539 pl022->cur_msg = NULL; 540 pl022->cur_transfer = NULL; 541 pl022->cur_chip = NULL; 542 543 /* disable the SPI/SSP operation */ 544 writew((readw(SSP_CR1(pl022->virtbase)) & 545 (~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase)); 546 547 spi_finalize_current_message(pl022->master); 548 } 549 550 /** 551 * flush - flush the FIFO to reach a clean state 552 * @pl022: SSP driver private data structure 553 */ 554 static int flush(struct pl022 *pl022) 555 { 556 unsigned long limit = loops_per_jiffy << 1; 557 558 dev_dbg(&pl022->adev->dev, "flush\n"); 559 do { 560 while (readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RNE) 561 readw(SSP_DR(pl022->virtbase)); 562 } while ((readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_BSY) && limit--); 563 564 pl022->exp_fifo_level = 0; 565 566 return limit; 567 } 568 569 /** 570 * restore_state - Load configuration of current chip 571 * @pl022: SSP driver private data structure 572 */ 573 static void restore_state(struct pl022 *pl022) 574 { 575 struct chip_data *chip = pl022->cur_chip; 576 577 if (pl022->vendor->extended_cr) 578 writel(chip->cr0, SSP_CR0(pl022->virtbase)); 579 else 580 writew(chip->cr0, SSP_CR0(pl022->virtbase)); 581 writew(chip->cr1, SSP_CR1(pl022->virtbase)); 582 writew(chip->dmacr, SSP_DMACR(pl022->virtbase)); 583 writew(chip->cpsr, SSP_CPSR(pl022->virtbase)); 584 writew(DISABLE_ALL_INTERRUPTS, SSP_IMSC(pl022->virtbase)); 585 writew(CLEAR_ALL_INTERRUPTS, SSP_ICR(pl022->virtbase)); 586 } 587 588 /* 589 * Default SSP Register Values 590 */ 591 #define DEFAULT_SSP_REG_CR0 ( \ 592 GEN_MASK_BITS(SSP_DATA_BITS_12, SSP_CR0_MASK_DSS, 0) | \ 593 GEN_MASK_BITS(SSP_INTERFACE_MOTOROLA_SPI, SSP_CR0_MASK_FRF, 4) | \ 594 GEN_MASK_BITS(SSP_CLK_POL_IDLE_LOW, SSP_CR0_MASK_SPO, 6) | \ 595 GEN_MASK_BITS(SSP_CLK_SECOND_EDGE, SSP_CR0_MASK_SPH, 7) | \ 596 GEN_MASK_BITS(SSP_DEFAULT_CLKRATE, SSP_CR0_MASK_SCR, 8) \ 597 ) 598 599 /* ST versions have slightly different bit layout */ 600 #define DEFAULT_SSP_REG_CR0_ST ( \ 601 GEN_MASK_BITS(SSP_DATA_BITS_12, SSP_CR0_MASK_DSS_ST, 0) | \ 602 GEN_MASK_BITS(SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, SSP_CR0_MASK_HALFDUP_ST, 5) | \ 603 GEN_MASK_BITS(SSP_CLK_POL_IDLE_LOW, SSP_CR0_MASK_SPO, 6) | \ 604 GEN_MASK_BITS(SSP_CLK_SECOND_EDGE, SSP_CR0_MASK_SPH, 7) | \ 605 GEN_MASK_BITS(SSP_DEFAULT_CLKRATE, SSP_CR0_MASK_SCR, 8) | \ 606 GEN_MASK_BITS(SSP_BITS_8, SSP_CR0_MASK_CSS_ST, 16) | \ 607 GEN_MASK_BITS(SSP_INTERFACE_MOTOROLA_SPI, SSP_CR0_MASK_FRF_ST, 21) \ 608 ) 609 610 /* The PL023 version is slightly different again */ 611 #define DEFAULT_SSP_REG_CR0_ST_PL023 ( \ 612 GEN_MASK_BITS(SSP_DATA_BITS_12, SSP_CR0_MASK_DSS_ST, 0) | \ 613 GEN_MASK_BITS(SSP_CLK_POL_IDLE_LOW, SSP_CR0_MASK_SPO, 6) | \ 614 GEN_MASK_BITS(SSP_CLK_SECOND_EDGE, SSP_CR0_MASK_SPH, 7) | \ 615 GEN_MASK_BITS(SSP_DEFAULT_CLKRATE, SSP_CR0_MASK_SCR, 8) \ 616 ) 617 618 #define DEFAULT_SSP_REG_CR1 ( \ 619 GEN_MASK_BITS(LOOPBACK_DISABLED, SSP_CR1_MASK_LBM, 0) | \ 620 GEN_MASK_BITS(SSP_DISABLED, SSP_CR1_MASK_SSE, 1) | \ 621 GEN_MASK_BITS(SSP_MASTER, SSP_CR1_MASK_MS, 2) | \ 622 GEN_MASK_BITS(DO_NOT_DRIVE_TX, SSP_CR1_MASK_SOD, 3) \ 623 ) 624 625 /* ST versions extend this register to use all 16 bits */ 626 #define DEFAULT_SSP_REG_CR1_ST ( \ 627 DEFAULT_SSP_REG_CR1 | \ 628 GEN_MASK_BITS(SSP_RX_MSB, SSP_CR1_MASK_RENDN_ST, 4) | \ 629 GEN_MASK_BITS(SSP_TX_MSB, SSP_CR1_MASK_TENDN_ST, 5) | \ 630 GEN_MASK_BITS(SSP_MWIRE_WAIT_ZERO, SSP_CR1_MASK_MWAIT_ST, 6) |\ 631 GEN_MASK_BITS(SSP_RX_1_OR_MORE_ELEM, SSP_CR1_MASK_RXIFLSEL_ST, 7) | \ 632 GEN_MASK_BITS(SSP_TX_1_OR_MORE_EMPTY_LOC, SSP_CR1_MASK_TXIFLSEL_ST, 10) \ 633 ) 634 635 /* 636 * The PL023 variant has further differences: no loopback mode, no microwire 637 * support, and a new clock feedback delay setting. 638 */ 639 #define DEFAULT_SSP_REG_CR1_ST_PL023 ( \ 640 GEN_MASK_BITS(SSP_DISABLED, SSP_CR1_MASK_SSE, 1) | \ 641 GEN_MASK_BITS(SSP_MASTER, SSP_CR1_MASK_MS, 2) | \ 642 GEN_MASK_BITS(DO_NOT_DRIVE_TX, SSP_CR1_MASK_SOD, 3) | \ 643 GEN_MASK_BITS(SSP_RX_MSB, SSP_CR1_MASK_RENDN_ST, 4) | \ 644 GEN_MASK_BITS(SSP_TX_MSB, SSP_CR1_MASK_TENDN_ST, 5) | \ 645 GEN_MASK_BITS(SSP_RX_1_OR_MORE_ELEM, SSP_CR1_MASK_RXIFLSEL_ST, 7) | \ 646 GEN_MASK_BITS(SSP_TX_1_OR_MORE_EMPTY_LOC, SSP_CR1_MASK_TXIFLSEL_ST, 10) | \ 647 GEN_MASK_BITS(SSP_FEEDBACK_CLK_DELAY_NONE, SSP_CR1_MASK_FBCLKDEL_ST, 13) \ 648 ) 649 650 #define DEFAULT_SSP_REG_CPSR ( \ 651 GEN_MASK_BITS(SSP_DEFAULT_PRESCALE, SSP_CPSR_MASK_CPSDVSR, 0) \ 652 ) 653 654 #define DEFAULT_SSP_REG_DMACR (\ 655 GEN_MASK_BITS(SSP_DMA_DISABLED, SSP_DMACR_MASK_RXDMAE, 0) | \ 656 GEN_MASK_BITS(SSP_DMA_DISABLED, SSP_DMACR_MASK_TXDMAE, 1) \ 657 ) 658 659 /** 660 * load_ssp_default_config - Load default configuration for SSP 661 * @pl022: SSP driver private data structure 662 */ 663 static void load_ssp_default_config(struct pl022 *pl022) 664 { 665 if (pl022->vendor->pl023) { 666 writel(DEFAULT_SSP_REG_CR0_ST_PL023, SSP_CR0(pl022->virtbase)); 667 writew(DEFAULT_SSP_REG_CR1_ST_PL023, SSP_CR1(pl022->virtbase)); 668 } else if (pl022->vendor->extended_cr) { 669 writel(DEFAULT_SSP_REG_CR0_ST, SSP_CR0(pl022->virtbase)); 670 writew(DEFAULT_SSP_REG_CR1_ST, SSP_CR1(pl022->virtbase)); 671 } else { 672 writew(DEFAULT_SSP_REG_CR0, SSP_CR0(pl022->virtbase)); 673 writew(DEFAULT_SSP_REG_CR1, SSP_CR1(pl022->virtbase)); 674 } 675 writew(DEFAULT_SSP_REG_DMACR, SSP_DMACR(pl022->virtbase)); 676 writew(DEFAULT_SSP_REG_CPSR, SSP_CPSR(pl022->virtbase)); 677 writew(DISABLE_ALL_INTERRUPTS, SSP_IMSC(pl022->virtbase)); 678 writew(CLEAR_ALL_INTERRUPTS, SSP_ICR(pl022->virtbase)); 679 } 680 681 /** 682 * This will write to TX and read from RX according to the parameters 683 * set in pl022. 684 */ 685 static void readwriter(struct pl022 *pl022) 686 { 687 688 /* 689 * The FIFO depth is different between primecell variants. 690 * I believe filling in too much in the FIFO might cause 691 * errons in 8bit wide transfers on ARM variants (just 8 words 692 * FIFO, means only 8x8 = 64 bits in FIFO) at least. 693 * 694 * To prevent this issue, the TX FIFO is only filled to the 695 * unused RX FIFO fill length, regardless of what the TX 696 * FIFO status flag indicates. 697 */ 698 dev_dbg(&pl022->adev->dev, 699 "%s, rx: %p, rxend: %p, tx: %p, txend: %p\n", 700 __func__, pl022->rx, pl022->rx_end, pl022->tx, pl022->tx_end); 701 702 /* Read as much as you can */ 703 while ((readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RNE) 704 && (pl022->rx < pl022->rx_end)) { 705 switch (pl022->read) { 706 case READING_NULL: 707 readw(SSP_DR(pl022->virtbase)); 708 break; 709 case READING_U8: 710 *(u8 *) (pl022->rx) = 711 readw(SSP_DR(pl022->virtbase)) & 0xFFU; 712 break; 713 case READING_U16: 714 *(u16 *) (pl022->rx) = 715 (u16) readw(SSP_DR(pl022->virtbase)); 716 break; 717 case READING_U32: 718 *(u32 *) (pl022->rx) = 719 readl(SSP_DR(pl022->virtbase)); 720 break; 721 } 722 pl022->rx += (pl022->cur_chip->n_bytes); 723 pl022->exp_fifo_level--; 724 } 725 /* 726 * Write as much as possible up to the RX FIFO size 727 */ 728 while ((pl022->exp_fifo_level < pl022->vendor->fifodepth) 729 && (pl022->tx < pl022->tx_end)) { 730 switch (pl022->write) { 731 case WRITING_NULL: 732 writew(0x0, SSP_DR(pl022->virtbase)); 733 break; 734 case WRITING_U8: 735 writew(*(u8 *) (pl022->tx), SSP_DR(pl022->virtbase)); 736 break; 737 case WRITING_U16: 738 writew((*(u16 *) (pl022->tx)), SSP_DR(pl022->virtbase)); 739 break; 740 case WRITING_U32: 741 writel(*(u32 *) (pl022->tx), SSP_DR(pl022->virtbase)); 742 break; 743 } 744 pl022->tx += (pl022->cur_chip->n_bytes); 745 pl022->exp_fifo_level++; 746 /* 747 * This inner reader takes care of things appearing in the RX 748 * FIFO as we're transmitting. This will happen a lot since the 749 * clock starts running when you put things into the TX FIFO, 750 * and then things are continuously clocked into the RX FIFO. 751 */ 752 while ((readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RNE) 753 && (pl022->rx < pl022->rx_end)) { 754 switch (pl022->read) { 755 case READING_NULL: 756 readw(SSP_DR(pl022->virtbase)); 757 break; 758 case READING_U8: 759 *(u8 *) (pl022->rx) = 760 readw(SSP_DR(pl022->virtbase)) & 0xFFU; 761 break; 762 case READING_U16: 763 *(u16 *) (pl022->rx) = 764 (u16) readw(SSP_DR(pl022->virtbase)); 765 break; 766 case READING_U32: 767 *(u32 *) (pl022->rx) = 768 readl(SSP_DR(pl022->virtbase)); 769 break; 770 } 771 pl022->rx += (pl022->cur_chip->n_bytes); 772 pl022->exp_fifo_level--; 773 } 774 } 775 /* 776 * When we exit here the TX FIFO should be full and the RX FIFO 777 * should be empty 778 */ 779 } 780 781 /** 782 * next_transfer - Move to the Next transfer in the current spi message 783 * @pl022: SSP driver private data structure 784 * 785 * This function moves though the linked list of spi transfers in the 786 * current spi message and returns with the state of current spi 787 * message i.e whether its last transfer is done(STATE_DONE) or 788 * Next transfer is ready(STATE_RUNNING) 789 */ 790 static void *next_transfer(struct pl022 *pl022) 791 { 792 struct spi_message *msg = pl022->cur_msg; 793 struct spi_transfer *trans = pl022->cur_transfer; 794 795 /* Move to next transfer */ 796 if (trans->transfer_list.next != &msg->transfers) { 797 pl022->cur_transfer = 798 list_entry(trans->transfer_list.next, 799 struct spi_transfer, transfer_list); 800 return STATE_RUNNING; 801 } 802 return STATE_DONE; 803 } 804 805 /* 806 * This DMA functionality is only compiled in if we have 807 * access to the generic DMA devices/DMA engine. 808 */ 809 #ifdef CONFIG_DMA_ENGINE 810 static void unmap_free_dma_scatter(struct pl022 *pl022) 811 { 812 /* Unmap and free the SG tables */ 813 dma_unmap_sg(pl022->dma_tx_channel->device->dev, pl022->sgt_tx.sgl, 814 pl022->sgt_tx.nents, DMA_TO_DEVICE); 815 dma_unmap_sg(pl022->dma_rx_channel->device->dev, pl022->sgt_rx.sgl, 816 pl022->sgt_rx.nents, DMA_FROM_DEVICE); 817 sg_free_table(&pl022->sgt_rx); 818 sg_free_table(&pl022->sgt_tx); 819 } 820 821 static void dma_callback(void *data) 822 { 823 struct pl022 *pl022 = data; 824 struct spi_message *msg = pl022->cur_msg; 825 826 BUG_ON(!pl022->sgt_rx.sgl); 827 828 #ifdef VERBOSE_DEBUG 829 /* 830 * Optionally dump out buffers to inspect contents, this is 831 * good if you want to convince yourself that the loopback 832 * read/write contents are the same, when adopting to a new 833 * DMA engine. 834 */ 835 { 836 struct scatterlist *sg; 837 unsigned int i; 838 839 dma_sync_sg_for_cpu(&pl022->adev->dev, 840 pl022->sgt_rx.sgl, 841 pl022->sgt_rx.nents, 842 DMA_FROM_DEVICE); 843 844 for_each_sg(pl022->sgt_rx.sgl, sg, pl022->sgt_rx.nents, i) { 845 dev_dbg(&pl022->adev->dev, "SPI RX SG ENTRY: %d", i); 846 print_hex_dump(KERN_ERR, "SPI RX: ", 847 DUMP_PREFIX_OFFSET, 848 16, 849 1, 850 sg_virt(sg), 851 sg_dma_len(sg), 852 1); 853 } 854 for_each_sg(pl022->sgt_tx.sgl, sg, pl022->sgt_tx.nents, i) { 855 dev_dbg(&pl022->adev->dev, "SPI TX SG ENTRY: %d", i); 856 print_hex_dump(KERN_ERR, "SPI TX: ", 857 DUMP_PREFIX_OFFSET, 858 16, 859 1, 860 sg_virt(sg), 861 sg_dma_len(sg), 862 1); 863 } 864 } 865 #endif 866 867 unmap_free_dma_scatter(pl022); 868 869 /* Update total bytes transferred */ 870 msg->actual_length += pl022->cur_transfer->len; 871 if (pl022->cur_transfer->cs_change) 872 pl022_cs_control(pl022, SSP_CHIP_DESELECT); 873 874 /* Move to next transfer */ 875 msg->state = next_transfer(pl022); 876 tasklet_schedule(&pl022->pump_transfers); 877 } 878 879 static void setup_dma_scatter(struct pl022 *pl022, 880 void *buffer, 881 unsigned int length, 882 struct sg_table *sgtab) 883 { 884 struct scatterlist *sg; 885 int bytesleft = length; 886 void *bufp = buffer; 887 int mapbytes; 888 int i; 889 890 if (buffer) { 891 for_each_sg(sgtab->sgl, sg, sgtab->nents, i) { 892 /* 893 * If there are less bytes left than what fits 894 * in the current page (plus page alignment offset) 895 * we just feed in this, else we stuff in as much 896 * as we can. 897 */ 898 if (bytesleft < (PAGE_SIZE - offset_in_page(bufp))) 899 mapbytes = bytesleft; 900 else 901 mapbytes = PAGE_SIZE - offset_in_page(bufp); 902 sg_set_page(sg, virt_to_page(bufp), 903 mapbytes, offset_in_page(bufp)); 904 bufp += mapbytes; 905 bytesleft -= mapbytes; 906 dev_dbg(&pl022->adev->dev, 907 "set RX/TX target page @ %p, %d bytes, %d left\n", 908 bufp, mapbytes, bytesleft); 909 } 910 } else { 911 /* Map the dummy buffer on every page */ 912 for_each_sg(sgtab->sgl, sg, sgtab->nents, i) { 913 if (bytesleft < PAGE_SIZE) 914 mapbytes = bytesleft; 915 else 916 mapbytes = PAGE_SIZE; 917 sg_set_page(sg, virt_to_page(pl022->dummypage), 918 mapbytes, 0); 919 bytesleft -= mapbytes; 920 dev_dbg(&pl022->adev->dev, 921 "set RX/TX to dummy page %d bytes, %d left\n", 922 mapbytes, bytesleft); 923 924 } 925 } 926 BUG_ON(bytesleft); 927 } 928 929 /** 930 * configure_dma - configures the channels for the next transfer 931 * @pl022: SSP driver's private data structure 932 */ 933 static int configure_dma(struct pl022 *pl022) 934 { 935 struct dma_slave_config rx_conf = { 936 .src_addr = SSP_DR(pl022->phybase), 937 .direction = DMA_DEV_TO_MEM, 938 .device_fc = false, 939 }; 940 struct dma_slave_config tx_conf = { 941 .dst_addr = SSP_DR(pl022->phybase), 942 .direction = DMA_MEM_TO_DEV, 943 .device_fc = false, 944 }; 945 unsigned int pages; 946 int ret; 947 int rx_sglen, tx_sglen; 948 struct dma_chan *rxchan = pl022->dma_rx_channel; 949 struct dma_chan *txchan = pl022->dma_tx_channel; 950 struct dma_async_tx_descriptor *rxdesc; 951 struct dma_async_tx_descriptor *txdesc; 952 953 /* Check that the channels are available */ 954 if (!rxchan || !txchan) 955 return -ENODEV; 956 957 /* 958 * If supplied, the DMA burstsize should equal the FIFO trigger level. 959 * Notice that the DMA engine uses one-to-one mapping. Since we can 960 * not trigger on 2 elements this needs explicit mapping rather than 961 * calculation. 962 */ 963 switch (pl022->rx_lev_trig) { 964 case SSP_RX_1_OR_MORE_ELEM: 965 rx_conf.src_maxburst = 1; 966 break; 967 case SSP_RX_4_OR_MORE_ELEM: 968 rx_conf.src_maxburst = 4; 969 break; 970 case SSP_RX_8_OR_MORE_ELEM: 971 rx_conf.src_maxburst = 8; 972 break; 973 case SSP_RX_16_OR_MORE_ELEM: 974 rx_conf.src_maxburst = 16; 975 break; 976 case SSP_RX_32_OR_MORE_ELEM: 977 rx_conf.src_maxburst = 32; 978 break; 979 default: 980 rx_conf.src_maxburst = pl022->vendor->fifodepth >> 1; 981 break; 982 } 983 984 switch (pl022->tx_lev_trig) { 985 case SSP_TX_1_OR_MORE_EMPTY_LOC: 986 tx_conf.dst_maxburst = 1; 987 break; 988 case SSP_TX_4_OR_MORE_EMPTY_LOC: 989 tx_conf.dst_maxburst = 4; 990 break; 991 case SSP_TX_8_OR_MORE_EMPTY_LOC: 992 tx_conf.dst_maxburst = 8; 993 break; 994 case SSP_TX_16_OR_MORE_EMPTY_LOC: 995 tx_conf.dst_maxburst = 16; 996 break; 997 case SSP_TX_32_OR_MORE_EMPTY_LOC: 998 tx_conf.dst_maxburst = 32; 999 break; 1000 default: 1001 tx_conf.dst_maxburst = pl022->vendor->fifodepth >> 1; 1002 break; 1003 } 1004 1005 switch (pl022->read) { 1006 case READING_NULL: 1007 /* Use the same as for writing */ 1008 rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_UNDEFINED; 1009 break; 1010 case READING_U8: 1011 rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 1012 break; 1013 case READING_U16: 1014 rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES; 1015 break; 1016 case READING_U32: 1017 rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; 1018 break; 1019 } 1020 1021 switch (pl022->write) { 1022 case WRITING_NULL: 1023 /* Use the same as for reading */ 1024 tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_UNDEFINED; 1025 break; 1026 case WRITING_U8: 1027 tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 1028 break; 1029 case WRITING_U16: 1030 tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES; 1031 break; 1032 case WRITING_U32: 1033 tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; 1034 break; 1035 } 1036 1037 /* SPI pecularity: we need to read and write the same width */ 1038 if (rx_conf.src_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED) 1039 rx_conf.src_addr_width = tx_conf.dst_addr_width; 1040 if (tx_conf.dst_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED) 1041 tx_conf.dst_addr_width = rx_conf.src_addr_width; 1042 BUG_ON(rx_conf.src_addr_width != tx_conf.dst_addr_width); 1043 1044 dmaengine_slave_config(rxchan, &rx_conf); 1045 dmaengine_slave_config(txchan, &tx_conf); 1046 1047 /* Create sglists for the transfers */ 1048 pages = DIV_ROUND_UP(pl022->cur_transfer->len, PAGE_SIZE); 1049 dev_dbg(&pl022->adev->dev, "using %d pages for transfer\n", pages); 1050 1051 ret = sg_alloc_table(&pl022->sgt_rx, pages, GFP_ATOMIC); 1052 if (ret) 1053 goto err_alloc_rx_sg; 1054 1055 ret = sg_alloc_table(&pl022->sgt_tx, pages, GFP_ATOMIC); 1056 if (ret) 1057 goto err_alloc_tx_sg; 1058 1059 /* Fill in the scatterlists for the RX+TX buffers */ 1060 setup_dma_scatter(pl022, pl022->rx, 1061 pl022->cur_transfer->len, &pl022->sgt_rx); 1062 setup_dma_scatter(pl022, pl022->tx, 1063 pl022->cur_transfer->len, &pl022->sgt_tx); 1064 1065 /* Map DMA buffers */ 1066 rx_sglen = dma_map_sg(rxchan->device->dev, pl022->sgt_rx.sgl, 1067 pl022->sgt_rx.nents, DMA_FROM_DEVICE); 1068 if (!rx_sglen) 1069 goto err_rx_sgmap; 1070 1071 tx_sglen = dma_map_sg(txchan->device->dev, pl022->sgt_tx.sgl, 1072 pl022->sgt_tx.nents, DMA_TO_DEVICE); 1073 if (!tx_sglen) 1074 goto err_tx_sgmap; 1075 1076 /* Send both scatterlists */ 1077 rxdesc = dmaengine_prep_slave_sg(rxchan, 1078 pl022->sgt_rx.sgl, 1079 rx_sglen, 1080 DMA_DEV_TO_MEM, 1081 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 1082 if (!rxdesc) 1083 goto err_rxdesc; 1084 1085 txdesc = dmaengine_prep_slave_sg(txchan, 1086 pl022->sgt_tx.sgl, 1087 tx_sglen, 1088 DMA_MEM_TO_DEV, 1089 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 1090 if (!txdesc) 1091 goto err_txdesc; 1092 1093 /* Put the callback on the RX transfer only, that should finish last */ 1094 rxdesc->callback = dma_callback; 1095 rxdesc->callback_param = pl022; 1096 1097 /* Submit and fire RX and TX with TX last so we're ready to read! */ 1098 dmaengine_submit(rxdesc); 1099 dmaengine_submit(txdesc); 1100 dma_async_issue_pending(rxchan); 1101 dma_async_issue_pending(txchan); 1102 pl022->dma_running = true; 1103 1104 return 0; 1105 1106 err_txdesc: 1107 dmaengine_terminate_all(txchan); 1108 err_rxdesc: 1109 dmaengine_terminate_all(rxchan); 1110 dma_unmap_sg(txchan->device->dev, pl022->sgt_tx.sgl, 1111 pl022->sgt_tx.nents, DMA_TO_DEVICE); 1112 err_tx_sgmap: 1113 dma_unmap_sg(rxchan->device->dev, pl022->sgt_rx.sgl, 1114 pl022->sgt_rx.nents, DMA_FROM_DEVICE); 1115 err_rx_sgmap: 1116 sg_free_table(&pl022->sgt_tx); 1117 err_alloc_tx_sg: 1118 sg_free_table(&pl022->sgt_rx); 1119 err_alloc_rx_sg: 1120 return -ENOMEM; 1121 } 1122 1123 static int pl022_dma_probe(struct pl022 *pl022) 1124 { 1125 dma_cap_mask_t mask; 1126 1127 /* Try to acquire a generic DMA engine slave channel */ 1128 dma_cap_zero(mask); 1129 dma_cap_set(DMA_SLAVE, mask); 1130 /* 1131 * We need both RX and TX channels to do DMA, else do none 1132 * of them. 1133 */ 1134 pl022->dma_rx_channel = dma_request_channel(mask, 1135 pl022->master_info->dma_filter, 1136 pl022->master_info->dma_rx_param); 1137 if (!pl022->dma_rx_channel) { 1138 dev_dbg(&pl022->adev->dev, "no RX DMA channel!\n"); 1139 goto err_no_rxchan; 1140 } 1141 1142 pl022->dma_tx_channel = dma_request_channel(mask, 1143 pl022->master_info->dma_filter, 1144 pl022->master_info->dma_tx_param); 1145 if (!pl022->dma_tx_channel) { 1146 dev_dbg(&pl022->adev->dev, "no TX DMA channel!\n"); 1147 goto err_no_txchan; 1148 } 1149 1150 pl022->dummypage = kmalloc(PAGE_SIZE, GFP_KERNEL); 1151 if (!pl022->dummypage) 1152 goto err_no_dummypage; 1153 1154 dev_info(&pl022->adev->dev, "setup for DMA on RX %s, TX %s\n", 1155 dma_chan_name(pl022->dma_rx_channel), 1156 dma_chan_name(pl022->dma_tx_channel)); 1157 1158 return 0; 1159 1160 err_no_dummypage: 1161 dma_release_channel(pl022->dma_tx_channel); 1162 err_no_txchan: 1163 dma_release_channel(pl022->dma_rx_channel); 1164 pl022->dma_rx_channel = NULL; 1165 err_no_rxchan: 1166 dev_err(&pl022->adev->dev, 1167 "Failed to work in dma mode, work without dma!\n"); 1168 return -ENODEV; 1169 } 1170 1171 static int pl022_dma_autoprobe(struct pl022 *pl022) 1172 { 1173 struct device *dev = &pl022->adev->dev; 1174 struct dma_chan *chan; 1175 int err; 1176 1177 /* automatically configure DMA channels from platform, normally using DT */ 1178 chan = dma_request_slave_channel_reason(dev, "rx"); 1179 if (IS_ERR(chan)) { 1180 err = PTR_ERR(chan); 1181 goto err_no_rxchan; 1182 } 1183 1184 pl022->dma_rx_channel = chan; 1185 1186 chan = dma_request_slave_channel_reason(dev, "tx"); 1187 if (IS_ERR(chan)) { 1188 err = PTR_ERR(chan); 1189 goto err_no_txchan; 1190 } 1191 1192 pl022->dma_tx_channel = chan; 1193 1194 pl022->dummypage = kmalloc(PAGE_SIZE, GFP_KERNEL); 1195 if (!pl022->dummypage) { 1196 err = -ENOMEM; 1197 goto err_no_dummypage; 1198 } 1199 1200 return 0; 1201 1202 err_no_dummypage: 1203 dma_release_channel(pl022->dma_tx_channel); 1204 pl022->dma_tx_channel = NULL; 1205 err_no_txchan: 1206 dma_release_channel(pl022->dma_rx_channel); 1207 pl022->dma_rx_channel = NULL; 1208 err_no_rxchan: 1209 return err; 1210 } 1211 1212 static void terminate_dma(struct pl022 *pl022) 1213 { 1214 struct dma_chan *rxchan = pl022->dma_rx_channel; 1215 struct dma_chan *txchan = pl022->dma_tx_channel; 1216 1217 dmaengine_terminate_all(rxchan); 1218 dmaengine_terminate_all(txchan); 1219 unmap_free_dma_scatter(pl022); 1220 pl022->dma_running = false; 1221 } 1222 1223 static void pl022_dma_remove(struct pl022 *pl022) 1224 { 1225 if (pl022->dma_running) 1226 terminate_dma(pl022); 1227 if (pl022->dma_tx_channel) 1228 dma_release_channel(pl022->dma_tx_channel); 1229 if (pl022->dma_rx_channel) 1230 dma_release_channel(pl022->dma_rx_channel); 1231 kfree(pl022->dummypage); 1232 } 1233 1234 #else 1235 static inline int configure_dma(struct pl022 *pl022) 1236 { 1237 return -ENODEV; 1238 } 1239 1240 static inline int pl022_dma_autoprobe(struct pl022 *pl022) 1241 { 1242 return 0; 1243 } 1244 1245 static inline int pl022_dma_probe(struct pl022 *pl022) 1246 { 1247 return 0; 1248 } 1249 1250 static inline void pl022_dma_remove(struct pl022 *pl022) 1251 { 1252 } 1253 #endif 1254 1255 /** 1256 * pl022_interrupt_handler - Interrupt handler for SSP controller 1257 * 1258 * This function handles interrupts generated for an interrupt based transfer. 1259 * If a receive overrun (ROR) interrupt is there then we disable SSP, flag the 1260 * current message's state as STATE_ERROR and schedule the tasklet 1261 * pump_transfers which will do the postprocessing of the current message by 1262 * calling giveback(). Otherwise it reads data from RX FIFO till there is no 1263 * more data, and writes data in TX FIFO till it is not full. If we complete 1264 * the transfer we move to the next transfer and schedule the tasklet. 1265 */ 1266 static irqreturn_t pl022_interrupt_handler(int irq, void *dev_id) 1267 { 1268 struct pl022 *pl022 = dev_id; 1269 struct spi_message *msg = pl022->cur_msg; 1270 u16 irq_status = 0; 1271 1272 if (unlikely(!msg)) { 1273 dev_err(&pl022->adev->dev, 1274 "bad message state in interrupt handler"); 1275 /* Never fail */ 1276 return IRQ_HANDLED; 1277 } 1278 1279 /* Read the Interrupt Status Register */ 1280 irq_status = readw(SSP_MIS(pl022->virtbase)); 1281 1282 if (unlikely(!irq_status)) 1283 return IRQ_NONE; 1284 1285 /* 1286 * This handles the FIFO interrupts, the timeout 1287 * interrupts are flatly ignored, they cannot be 1288 * trusted. 1289 */ 1290 if (unlikely(irq_status & SSP_MIS_MASK_RORMIS)) { 1291 /* 1292 * Overrun interrupt - bail out since our Data has been 1293 * corrupted 1294 */ 1295 dev_err(&pl022->adev->dev, "FIFO overrun\n"); 1296 if (readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RFF) 1297 dev_err(&pl022->adev->dev, 1298 "RXFIFO is full\n"); 1299 1300 /* 1301 * Disable and clear interrupts, disable SSP, 1302 * mark message with bad status so it can be 1303 * retried. 1304 */ 1305 writew(DISABLE_ALL_INTERRUPTS, 1306 SSP_IMSC(pl022->virtbase)); 1307 writew(CLEAR_ALL_INTERRUPTS, SSP_ICR(pl022->virtbase)); 1308 writew((readw(SSP_CR1(pl022->virtbase)) & 1309 (~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase)); 1310 msg->state = STATE_ERROR; 1311 1312 /* Schedule message queue handler */ 1313 tasklet_schedule(&pl022->pump_transfers); 1314 return IRQ_HANDLED; 1315 } 1316 1317 readwriter(pl022); 1318 1319 if (pl022->tx == pl022->tx_end) { 1320 /* Disable Transmit interrupt, enable receive interrupt */ 1321 writew((readw(SSP_IMSC(pl022->virtbase)) & 1322 ~SSP_IMSC_MASK_TXIM) | SSP_IMSC_MASK_RXIM, 1323 SSP_IMSC(pl022->virtbase)); 1324 } 1325 1326 /* 1327 * Since all transactions must write as much as shall be read, 1328 * we can conclude the entire transaction once RX is complete. 1329 * At this point, all TX will always be finished. 1330 */ 1331 if (pl022->rx >= pl022->rx_end) { 1332 writew(DISABLE_ALL_INTERRUPTS, 1333 SSP_IMSC(pl022->virtbase)); 1334 writew(CLEAR_ALL_INTERRUPTS, SSP_ICR(pl022->virtbase)); 1335 if (unlikely(pl022->rx > pl022->rx_end)) { 1336 dev_warn(&pl022->adev->dev, "read %u surplus " 1337 "bytes (did you request an odd " 1338 "number of bytes on a 16bit bus?)\n", 1339 (u32) (pl022->rx - pl022->rx_end)); 1340 } 1341 /* Update total bytes transferred */ 1342 msg->actual_length += pl022->cur_transfer->len; 1343 if (pl022->cur_transfer->cs_change) 1344 pl022_cs_control(pl022, SSP_CHIP_DESELECT); 1345 /* Move to next transfer */ 1346 msg->state = next_transfer(pl022); 1347 tasklet_schedule(&pl022->pump_transfers); 1348 return IRQ_HANDLED; 1349 } 1350 1351 return IRQ_HANDLED; 1352 } 1353 1354 /** 1355 * This sets up the pointers to memory for the next message to 1356 * send out on the SPI bus. 1357 */ 1358 static int set_up_next_transfer(struct pl022 *pl022, 1359 struct spi_transfer *transfer) 1360 { 1361 int residue; 1362 1363 /* Sanity check the message for this bus width */ 1364 residue = pl022->cur_transfer->len % pl022->cur_chip->n_bytes; 1365 if (unlikely(residue != 0)) { 1366 dev_err(&pl022->adev->dev, 1367 "message of %u bytes to transmit but the current " 1368 "chip bus has a data width of %u bytes!\n", 1369 pl022->cur_transfer->len, 1370 pl022->cur_chip->n_bytes); 1371 dev_err(&pl022->adev->dev, "skipping this message\n"); 1372 return -EIO; 1373 } 1374 pl022->tx = (void *)transfer->tx_buf; 1375 pl022->tx_end = pl022->tx + pl022->cur_transfer->len; 1376 pl022->rx = (void *)transfer->rx_buf; 1377 pl022->rx_end = pl022->rx + pl022->cur_transfer->len; 1378 pl022->write = 1379 pl022->tx ? pl022->cur_chip->write : WRITING_NULL; 1380 pl022->read = pl022->rx ? pl022->cur_chip->read : READING_NULL; 1381 return 0; 1382 } 1383 1384 /** 1385 * pump_transfers - Tasklet function which schedules next transfer 1386 * when running in interrupt or DMA transfer mode. 1387 * @data: SSP driver private data structure 1388 * 1389 */ 1390 static void pump_transfers(unsigned long data) 1391 { 1392 struct pl022 *pl022 = (struct pl022 *) data; 1393 struct spi_message *message = NULL; 1394 struct spi_transfer *transfer = NULL; 1395 struct spi_transfer *previous = NULL; 1396 1397 /* Get current state information */ 1398 message = pl022->cur_msg; 1399 transfer = pl022->cur_transfer; 1400 1401 /* Handle for abort */ 1402 if (message->state == STATE_ERROR) { 1403 message->status = -EIO; 1404 giveback(pl022); 1405 return; 1406 } 1407 1408 /* Handle end of message */ 1409 if (message->state == STATE_DONE) { 1410 message->status = 0; 1411 giveback(pl022); 1412 return; 1413 } 1414 1415 /* Delay if requested at end of transfer before CS change */ 1416 if (message->state == STATE_RUNNING) { 1417 previous = list_entry(transfer->transfer_list.prev, 1418 struct spi_transfer, 1419 transfer_list); 1420 if (previous->delay_usecs) 1421 /* 1422 * FIXME: This runs in interrupt context. 1423 * Is this really smart? 1424 */ 1425 udelay(previous->delay_usecs); 1426 1427 /* Reselect chip select only if cs_change was requested */ 1428 if (previous->cs_change) 1429 pl022_cs_control(pl022, SSP_CHIP_SELECT); 1430 } else { 1431 /* STATE_START */ 1432 message->state = STATE_RUNNING; 1433 } 1434 1435 if (set_up_next_transfer(pl022, transfer)) { 1436 message->state = STATE_ERROR; 1437 message->status = -EIO; 1438 giveback(pl022); 1439 return; 1440 } 1441 /* Flush the FIFOs and let's go! */ 1442 flush(pl022); 1443 1444 if (pl022->cur_chip->enable_dma) { 1445 if (configure_dma(pl022)) { 1446 dev_dbg(&pl022->adev->dev, 1447 "configuration of DMA failed, fall back to interrupt mode\n"); 1448 goto err_config_dma; 1449 } 1450 return; 1451 } 1452 1453 err_config_dma: 1454 /* enable all interrupts except RX */ 1455 writew(ENABLE_ALL_INTERRUPTS & ~SSP_IMSC_MASK_RXIM, SSP_IMSC(pl022->virtbase)); 1456 } 1457 1458 static void do_interrupt_dma_transfer(struct pl022 *pl022) 1459 { 1460 /* 1461 * Default is to enable all interrupts except RX - 1462 * this will be enabled once TX is complete 1463 */ 1464 u32 irqflags = (u32)(ENABLE_ALL_INTERRUPTS & ~SSP_IMSC_MASK_RXIM); 1465 1466 /* Enable target chip, if not already active */ 1467 if (!pl022->next_msg_cs_active) 1468 pl022_cs_control(pl022, SSP_CHIP_SELECT); 1469 1470 if (set_up_next_transfer(pl022, pl022->cur_transfer)) { 1471 /* Error path */ 1472 pl022->cur_msg->state = STATE_ERROR; 1473 pl022->cur_msg->status = -EIO; 1474 giveback(pl022); 1475 return; 1476 } 1477 /* If we're using DMA, set up DMA here */ 1478 if (pl022->cur_chip->enable_dma) { 1479 /* Configure DMA transfer */ 1480 if (configure_dma(pl022)) { 1481 dev_dbg(&pl022->adev->dev, 1482 "configuration of DMA failed, fall back to interrupt mode\n"); 1483 goto err_config_dma; 1484 } 1485 /* Disable interrupts in DMA mode, IRQ from DMA controller */ 1486 irqflags = DISABLE_ALL_INTERRUPTS; 1487 } 1488 err_config_dma: 1489 /* Enable SSP, turn on interrupts */ 1490 writew((readw(SSP_CR1(pl022->virtbase)) | SSP_CR1_MASK_SSE), 1491 SSP_CR1(pl022->virtbase)); 1492 writew(irqflags, SSP_IMSC(pl022->virtbase)); 1493 } 1494 1495 static void do_polling_transfer(struct pl022 *pl022) 1496 { 1497 struct spi_message *message = NULL; 1498 struct spi_transfer *transfer = NULL; 1499 struct spi_transfer *previous = NULL; 1500 struct chip_data *chip; 1501 unsigned long time, timeout; 1502 1503 chip = pl022->cur_chip; 1504 message = pl022->cur_msg; 1505 1506 while (message->state != STATE_DONE) { 1507 /* Handle for abort */ 1508 if (message->state == STATE_ERROR) 1509 break; 1510 transfer = pl022->cur_transfer; 1511 1512 /* Delay if requested at end of transfer */ 1513 if (message->state == STATE_RUNNING) { 1514 previous = 1515 list_entry(transfer->transfer_list.prev, 1516 struct spi_transfer, transfer_list); 1517 if (previous->delay_usecs) 1518 udelay(previous->delay_usecs); 1519 if (previous->cs_change) 1520 pl022_cs_control(pl022, SSP_CHIP_SELECT); 1521 } else { 1522 /* STATE_START */ 1523 message->state = STATE_RUNNING; 1524 if (!pl022->next_msg_cs_active) 1525 pl022_cs_control(pl022, SSP_CHIP_SELECT); 1526 } 1527 1528 /* Configuration Changing Per Transfer */ 1529 if (set_up_next_transfer(pl022, transfer)) { 1530 /* Error path */ 1531 message->state = STATE_ERROR; 1532 break; 1533 } 1534 /* Flush FIFOs and enable SSP */ 1535 flush(pl022); 1536 writew((readw(SSP_CR1(pl022->virtbase)) | SSP_CR1_MASK_SSE), 1537 SSP_CR1(pl022->virtbase)); 1538 1539 dev_dbg(&pl022->adev->dev, "polling transfer ongoing ...\n"); 1540 1541 timeout = jiffies + msecs_to_jiffies(SPI_POLLING_TIMEOUT); 1542 while (pl022->tx < pl022->tx_end || pl022->rx < pl022->rx_end) { 1543 time = jiffies; 1544 readwriter(pl022); 1545 if (time_after(time, timeout)) { 1546 dev_warn(&pl022->adev->dev, 1547 "%s: timeout!\n", __func__); 1548 message->state = STATE_ERROR; 1549 goto out; 1550 } 1551 cpu_relax(); 1552 } 1553 1554 /* Update total byte transferred */ 1555 message->actual_length += pl022->cur_transfer->len; 1556 if (pl022->cur_transfer->cs_change) 1557 pl022_cs_control(pl022, SSP_CHIP_DESELECT); 1558 /* Move to next transfer */ 1559 message->state = next_transfer(pl022); 1560 } 1561 out: 1562 /* Handle end of message */ 1563 if (message->state == STATE_DONE) 1564 message->status = 0; 1565 else 1566 message->status = -EIO; 1567 1568 giveback(pl022); 1569 return; 1570 } 1571 1572 static int pl022_transfer_one_message(struct spi_master *master, 1573 struct spi_message *msg) 1574 { 1575 struct pl022 *pl022 = spi_master_get_devdata(master); 1576 1577 /* Initial message state */ 1578 pl022->cur_msg = msg; 1579 msg->state = STATE_START; 1580 1581 pl022->cur_transfer = list_entry(msg->transfers.next, 1582 struct spi_transfer, transfer_list); 1583 1584 /* Setup the SPI using the per chip configuration */ 1585 pl022->cur_chip = spi_get_ctldata(msg->spi); 1586 pl022->cur_cs = pl022->chipselects[msg->spi->chip_select]; 1587 1588 restore_state(pl022); 1589 flush(pl022); 1590 1591 if (pl022->cur_chip->xfer_type == POLLING_TRANSFER) 1592 do_polling_transfer(pl022); 1593 else 1594 do_interrupt_dma_transfer(pl022); 1595 1596 return 0; 1597 } 1598 1599 static int pl022_unprepare_transfer_hardware(struct spi_master *master) 1600 { 1601 struct pl022 *pl022 = spi_master_get_devdata(master); 1602 1603 /* nothing more to do - disable spi/ssp and power off */ 1604 writew((readw(SSP_CR1(pl022->virtbase)) & 1605 (~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase)); 1606 1607 return 0; 1608 } 1609 1610 static int verify_controller_parameters(struct pl022 *pl022, 1611 struct pl022_config_chip const *chip_info) 1612 { 1613 if ((chip_info->iface < SSP_INTERFACE_MOTOROLA_SPI) 1614 || (chip_info->iface > SSP_INTERFACE_UNIDIRECTIONAL)) { 1615 dev_err(&pl022->adev->dev, 1616 "interface is configured incorrectly\n"); 1617 return -EINVAL; 1618 } 1619 if ((chip_info->iface == SSP_INTERFACE_UNIDIRECTIONAL) && 1620 (!pl022->vendor->unidir)) { 1621 dev_err(&pl022->adev->dev, 1622 "unidirectional mode not supported in this " 1623 "hardware version\n"); 1624 return -EINVAL; 1625 } 1626 if ((chip_info->hierarchy != SSP_MASTER) 1627 && (chip_info->hierarchy != SSP_SLAVE)) { 1628 dev_err(&pl022->adev->dev, 1629 "hierarchy is configured incorrectly\n"); 1630 return -EINVAL; 1631 } 1632 if ((chip_info->com_mode != INTERRUPT_TRANSFER) 1633 && (chip_info->com_mode != DMA_TRANSFER) 1634 && (chip_info->com_mode != POLLING_TRANSFER)) { 1635 dev_err(&pl022->adev->dev, 1636 "Communication mode is configured incorrectly\n"); 1637 return -EINVAL; 1638 } 1639 switch (chip_info->rx_lev_trig) { 1640 case SSP_RX_1_OR_MORE_ELEM: 1641 case SSP_RX_4_OR_MORE_ELEM: 1642 case SSP_RX_8_OR_MORE_ELEM: 1643 /* These are always OK, all variants can handle this */ 1644 break; 1645 case SSP_RX_16_OR_MORE_ELEM: 1646 if (pl022->vendor->fifodepth < 16) { 1647 dev_err(&pl022->adev->dev, 1648 "RX FIFO Trigger Level is configured incorrectly\n"); 1649 return -EINVAL; 1650 } 1651 break; 1652 case SSP_RX_32_OR_MORE_ELEM: 1653 if (pl022->vendor->fifodepth < 32) { 1654 dev_err(&pl022->adev->dev, 1655 "RX FIFO Trigger Level is configured incorrectly\n"); 1656 return -EINVAL; 1657 } 1658 break; 1659 default: 1660 dev_err(&pl022->adev->dev, 1661 "RX FIFO Trigger Level is configured incorrectly\n"); 1662 return -EINVAL; 1663 } 1664 switch (chip_info->tx_lev_trig) { 1665 case SSP_TX_1_OR_MORE_EMPTY_LOC: 1666 case SSP_TX_4_OR_MORE_EMPTY_LOC: 1667 case SSP_TX_8_OR_MORE_EMPTY_LOC: 1668 /* These are always OK, all variants can handle this */ 1669 break; 1670 case SSP_TX_16_OR_MORE_EMPTY_LOC: 1671 if (pl022->vendor->fifodepth < 16) { 1672 dev_err(&pl022->adev->dev, 1673 "TX FIFO Trigger Level is configured incorrectly\n"); 1674 return -EINVAL; 1675 } 1676 break; 1677 case SSP_TX_32_OR_MORE_EMPTY_LOC: 1678 if (pl022->vendor->fifodepth < 32) { 1679 dev_err(&pl022->adev->dev, 1680 "TX FIFO Trigger Level is configured incorrectly\n"); 1681 return -EINVAL; 1682 } 1683 break; 1684 default: 1685 dev_err(&pl022->adev->dev, 1686 "TX FIFO Trigger Level is configured incorrectly\n"); 1687 return -EINVAL; 1688 } 1689 if (chip_info->iface == SSP_INTERFACE_NATIONAL_MICROWIRE) { 1690 if ((chip_info->ctrl_len < SSP_BITS_4) 1691 || (chip_info->ctrl_len > SSP_BITS_32)) { 1692 dev_err(&pl022->adev->dev, 1693 "CTRL LEN is configured incorrectly\n"); 1694 return -EINVAL; 1695 } 1696 if ((chip_info->wait_state != SSP_MWIRE_WAIT_ZERO) 1697 && (chip_info->wait_state != SSP_MWIRE_WAIT_ONE)) { 1698 dev_err(&pl022->adev->dev, 1699 "Wait State is configured incorrectly\n"); 1700 return -EINVAL; 1701 } 1702 /* Half duplex is only available in the ST Micro version */ 1703 if (pl022->vendor->extended_cr) { 1704 if ((chip_info->duplex != 1705 SSP_MICROWIRE_CHANNEL_FULL_DUPLEX) 1706 && (chip_info->duplex != 1707 SSP_MICROWIRE_CHANNEL_HALF_DUPLEX)) { 1708 dev_err(&pl022->adev->dev, 1709 "Microwire duplex mode is configured incorrectly\n"); 1710 return -EINVAL; 1711 } 1712 } else { 1713 if (chip_info->duplex != SSP_MICROWIRE_CHANNEL_FULL_DUPLEX) 1714 dev_err(&pl022->adev->dev, 1715 "Microwire half duplex mode requested," 1716 " but this is only available in the" 1717 " ST version of PL022\n"); 1718 return -EINVAL; 1719 } 1720 } 1721 return 0; 1722 } 1723 1724 static inline u32 spi_rate(u32 rate, u16 cpsdvsr, u16 scr) 1725 { 1726 return rate / (cpsdvsr * (1 + scr)); 1727 } 1728 1729 static int calculate_effective_freq(struct pl022 *pl022, int freq, struct 1730 ssp_clock_params * clk_freq) 1731 { 1732 /* Lets calculate the frequency parameters */ 1733 u16 cpsdvsr = CPSDVR_MIN, scr = SCR_MIN; 1734 u32 rate, max_tclk, min_tclk, best_freq = 0, best_cpsdvsr = 0, 1735 best_scr = 0, tmp, found = 0; 1736 1737 rate = clk_get_rate(pl022->clk); 1738 /* cpsdvscr = 2 & scr 0 */ 1739 max_tclk = spi_rate(rate, CPSDVR_MIN, SCR_MIN); 1740 /* cpsdvsr = 254 & scr = 255 */ 1741 min_tclk = spi_rate(rate, CPSDVR_MAX, SCR_MAX); 1742 1743 if (freq > max_tclk) 1744 dev_warn(&pl022->adev->dev, 1745 "Max speed that can be programmed is %d Hz, you requested %d\n", 1746 max_tclk, freq); 1747 1748 if (freq < min_tclk) { 1749 dev_err(&pl022->adev->dev, 1750 "Requested frequency: %d Hz is less than minimum possible %d Hz\n", 1751 freq, min_tclk); 1752 return -EINVAL; 1753 } 1754 1755 /* 1756 * best_freq will give closest possible available rate (<= requested 1757 * freq) for all values of scr & cpsdvsr. 1758 */ 1759 while ((cpsdvsr <= CPSDVR_MAX) && !found) { 1760 while (scr <= SCR_MAX) { 1761 tmp = spi_rate(rate, cpsdvsr, scr); 1762 1763 if (tmp > freq) { 1764 /* we need lower freq */ 1765 scr++; 1766 continue; 1767 } 1768 1769 /* 1770 * If found exact value, mark found and break. 1771 * If found more closer value, update and break. 1772 */ 1773 if (tmp > best_freq) { 1774 best_freq = tmp; 1775 best_cpsdvsr = cpsdvsr; 1776 best_scr = scr; 1777 1778 if (tmp == freq) 1779 found = 1; 1780 } 1781 /* 1782 * increased scr will give lower rates, which are not 1783 * required 1784 */ 1785 break; 1786 } 1787 cpsdvsr += 2; 1788 scr = SCR_MIN; 1789 } 1790 1791 WARN(!best_freq, "pl022: Matching cpsdvsr and scr not found for %d Hz rate \n", 1792 freq); 1793 1794 clk_freq->cpsdvsr = (u8) (best_cpsdvsr & 0xFF); 1795 clk_freq->scr = (u8) (best_scr & 0xFF); 1796 dev_dbg(&pl022->adev->dev, 1797 "SSP Target Frequency is: %u, Effective Frequency is %u\n", 1798 freq, best_freq); 1799 dev_dbg(&pl022->adev->dev, "SSP cpsdvsr = %d, scr = %d\n", 1800 clk_freq->cpsdvsr, clk_freq->scr); 1801 1802 return 0; 1803 } 1804 1805 /* 1806 * A piece of default chip info unless the platform 1807 * supplies it. 1808 */ 1809 static const struct pl022_config_chip pl022_default_chip_info = { 1810 .com_mode = POLLING_TRANSFER, 1811 .iface = SSP_INTERFACE_MOTOROLA_SPI, 1812 .hierarchy = SSP_SLAVE, 1813 .slave_tx_disable = DO_NOT_DRIVE_TX, 1814 .rx_lev_trig = SSP_RX_1_OR_MORE_ELEM, 1815 .tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC, 1816 .ctrl_len = SSP_BITS_8, 1817 .wait_state = SSP_MWIRE_WAIT_ZERO, 1818 .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, 1819 .cs_control = null_cs_control, 1820 }; 1821 1822 /** 1823 * pl022_setup - setup function registered to SPI master framework 1824 * @spi: spi device which is requesting setup 1825 * 1826 * This function is registered to the SPI framework for this SPI master 1827 * controller. If it is the first time when setup is called by this device, 1828 * this function will initialize the runtime state for this chip and save 1829 * the same in the device structure. Else it will update the runtime info 1830 * with the updated chip info. Nothing is really being written to the 1831 * controller hardware here, that is not done until the actual transfer 1832 * commence. 1833 */ 1834 static int pl022_setup(struct spi_device *spi) 1835 { 1836 struct pl022_config_chip const *chip_info; 1837 struct pl022_config_chip chip_info_dt; 1838 struct chip_data *chip; 1839 struct ssp_clock_params clk_freq = { .cpsdvsr = 0, .scr = 0}; 1840 int status = 0; 1841 struct pl022 *pl022 = spi_master_get_devdata(spi->master); 1842 unsigned int bits = spi->bits_per_word; 1843 u32 tmp; 1844 struct device_node *np = spi->dev.of_node; 1845 1846 if (!spi->max_speed_hz) 1847 return -EINVAL; 1848 1849 /* Get controller_state if one is supplied */ 1850 chip = spi_get_ctldata(spi); 1851 1852 if (chip == NULL) { 1853 chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL); 1854 if (!chip) 1855 return -ENOMEM; 1856 dev_dbg(&spi->dev, 1857 "allocated memory for controller's runtime state\n"); 1858 } 1859 1860 /* Get controller data if one is supplied */ 1861 chip_info = spi->controller_data; 1862 1863 if (chip_info == NULL) { 1864 if (np) { 1865 chip_info_dt = pl022_default_chip_info; 1866 1867 chip_info_dt.hierarchy = SSP_MASTER; 1868 of_property_read_u32(np, "pl022,interface", 1869 &chip_info_dt.iface); 1870 of_property_read_u32(np, "pl022,com-mode", 1871 &chip_info_dt.com_mode); 1872 of_property_read_u32(np, "pl022,rx-level-trig", 1873 &chip_info_dt.rx_lev_trig); 1874 of_property_read_u32(np, "pl022,tx-level-trig", 1875 &chip_info_dt.tx_lev_trig); 1876 of_property_read_u32(np, "pl022,ctrl-len", 1877 &chip_info_dt.ctrl_len); 1878 of_property_read_u32(np, "pl022,wait-state", 1879 &chip_info_dt.wait_state); 1880 of_property_read_u32(np, "pl022,duplex", 1881 &chip_info_dt.duplex); 1882 1883 chip_info = &chip_info_dt; 1884 } else { 1885 chip_info = &pl022_default_chip_info; 1886 /* spi_board_info.controller_data not is supplied */ 1887 dev_dbg(&spi->dev, 1888 "using default controller_data settings\n"); 1889 } 1890 } else 1891 dev_dbg(&spi->dev, 1892 "using user supplied controller_data settings\n"); 1893 1894 /* 1895 * We can override with custom divisors, else we use the board 1896 * frequency setting 1897 */ 1898 if ((0 == chip_info->clk_freq.cpsdvsr) 1899 && (0 == chip_info->clk_freq.scr)) { 1900 status = calculate_effective_freq(pl022, 1901 spi->max_speed_hz, 1902 &clk_freq); 1903 if (status < 0) 1904 goto err_config_params; 1905 } else { 1906 memcpy(&clk_freq, &chip_info->clk_freq, sizeof(clk_freq)); 1907 if ((clk_freq.cpsdvsr % 2) != 0) 1908 clk_freq.cpsdvsr = 1909 clk_freq.cpsdvsr - 1; 1910 } 1911 if ((clk_freq.cpsdvsr < CPSDVR_MIN) 1912 || (clk_freq.cpsdvsr > CPSDVR_MAX)) { 1913 status = -EINVAL; 1914 dev_err(&spi->dev, 1915 "cpsdvsr is configured incorrectly\n"); 1916 goto err_config_params; 1917 } 1918 1919 status = verify_controller_parameters(pl022, chip_info); 1920 if (status) { 1921 dev_err(&spi->dev, "controller data is incorrect"); 1922 goto err_config_params; 1923 } 1924 1925 pl022->rx_lev_trig = chip_info->rx_lev_trig; 1926 pl022->tx_lev_trig = chip_info->tx_lev_trig; 1927 1928 /* Now set controller state based on controller data */ 1929 chip->xfer_type = chip_info->com_mode; 1930 if (!chip_info->cs_control) { 1931 chip->cs_control = null_cs_control; 1932 if (!gpio_is_valid(pl022->chipselects[spi->chip_select])) 1933 dev_warn(&spi->dev, 1934 "invalid chip select\n"); 1935 } else 1936 chip->cs_control = chip_info->cs_control; 1937 1938 /* Check bits per word with vendor specific range */ 1939 if ((bits <= 3) || (bits > pl022->vendor->max_bpw)) { 1940 status = -ENOTSUPP; 1941 dev_err(&spi->dev, "illegal data size for this controller!\n"); 1942 dev_err(&spi->dev, "This controller can only handle 4 <= n <= %d bit words\n", 1943 pl022->vendor->max_bpw); 1944 goto err_config_params; 1945 } else if (bits <= 8) { 1946 dev_dbg(&spi->dev, "4 <= n <=8 bits per word\n"); 1947 chip->n_bytes = 1; 1948 chip->read = READING_U8; 1949 chip->write = WRITING_U8; 1950 } else if (bits <= 16) { 1951 dev_dbg(&spi->dev, "9 <= n <= 16 bits per word\n"); 1952 chip->n_bytes = 2; 1953 chip->read = READING_U16; 1954 chip->write = WRITING_U16; 1955 } else { 1956 dev_dbg(&spi->dev, "17 <= n <= 32 bits per word\n"); 1957 chip->n_bytes = 4; 1958 chip->read = READING_U32; 1959 chip->write = WRITING_U32; 1960 } 1961 1962 /* Now Initialize all register settings required for this chip */ 1963 chip->cr0 = 0; 1964 chip->cr1 = 0; 1965 chip->dmacr = 0; 1966 chip->cpsr = 0; 1967 if ((chip_info->com_mode == DMA_TRANSFER) 1968 && ((pl022->master_info)->enable_dma)) { 1969 chip->enable_dma = true; 1970 dev_dbg(&spi->dev, "DMA mode set in controller state\n"); 1971 SSP_WRITE_BITS(chip->dmacr, SSP_DMA_ENABLED, 1972 SSP_DMACR_MASK_RXDMAE, 0); 1973 SSP_WRITE_BITS(chip->dmacr, SSP_DMA_ENABLED, 1974 SSP_DMACR_MASK_TXDMAE, 1); 1975 } else { 1976 chip->enable_dma = false; 1977 dev_dbg(&spi->dev, "DMA mode NOT set in controller state\n"); 1978 SSP_WRITE_BITS(chip->dmacr, SSP_DMA_DISABLED, 1979 SSP_DMACR_MASK_RXDMAE, 0); 1980 SSP_WRITE_BITS(chip->dmacr, SSP_DMA_DISABLED, 1981 SSP_DMACR_MASK_TXDMAE, 1); 1982 } 1983 1984 chip->cpsr = clk_freq.cpsdvsr; 1985 1986 /* Special setup for the ST micro extended control registers */ 1987 if (pl022->vendor->extended_cr) { 1988 u32 etx; 1989 1990 if (pl022->vendor->pl023) { 1991 /* These bits are only in the PL023 */ 1992 SSP_WRITE_BITS(chip->cr1, chip_info->clkdelay, 1993 SSP_CR1_MASK_FBCLKDEL_ST, 13); 1994 } else { 1995 /* These bits are in the PL022 but not PL023 */ 1996 SSP_WRITE_BITS(chip->cr0, chip_info->duplex, 1997 SSP_CR0_MASK_HALFDUP_ST, 5); 1998 SSP_WRITE_BITS(chip->cr0, chip_info->ctrl_len, 1999 SSP_CR0_MASK_CSS_ST, 16); 2000 SSP_WRITE_BITS(chip->cr0, chip_info->iface, 2001 SSP_CR0_MASK_FRF_ST, 21); 2002 SSP_WRITE_BITS(chip->cr1, chip_info->wait_state, 2003 SSP_CR1_MASK_MWAIT_ST, 6); 2004 } 2005 SSP_WRITE_BITS(chip->cr0, bits - 1, 2006 SSP_CR0_MASK_DSS_ST, 0); 2007 2008 if (spi->mode & SPI_LSB_FIRST) { 2009 tmp = SSP_RX_LSB; 2010 etx = SSP_TX_LSB; 2011 } else { 2012 tmp = SSP_RX_MSB; 2013 etx = SSP_TX_MSB; 2014 } 2015 SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_RENDN_ST, 4); 2016 SSP_WRITE_BITS(chip->cr1, etx, SSP_CR1_MASK_TENDN_ST, 5); 2017 SSP_WRITE_BITS(chip->cr1, chip_info->rx_lev_trig, 2018 SSP_CR1_MASK_RXIFLSEL_ST, 7); 2019 SSP_WRITE_BITS(chip->cr1, chip_info->tx_lev_trig, 2020 SSP_CR1_MASK_TXIFLSEL_ST, 10); 2021 } else { 2022 SSP_WRITE_BITS(chip->cr0, bits - 1, 2023 SSP_CR0_MASK_DSS, 0); 2024 SSP_WRITE_BITS(chip->cr0, chip_info->iface, 2025 SSP_CR0_MASK_FRF, 4); 2026 } 2027 2028 /* Stuff that is common for all versions */ 2029 if (spi->mode & SPI_CPOL) 2030 tmp = SSP_CLK_POL_IDLE_HIGH; 2031 else 2032 tmp = SSP_CLK_POL_IDLE_LOW; 2033 SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPO, 6); 2034 2035 if (spi->mode & SPI_CPHA) 2036 tmp = SSP_CLK_SECOND_EDGE; 2037 else 2038 tmp = SSP_CLK_FIRST_EDGE; 2039 SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPH, 7); 2040 2041 SSP_WRITE_BITS(chip->cr0, clk_freq.scr, SSP_CR0_MASK_SCR, 8); 2042 /* Loopback is available on all versions except PL023 */ 2043 if (pl022->vendor->loopback) { 2044 if (spi->mode & SPI_LOOP) 2045 tmp = LOOPBACK_ENABLED; 2046 else 2047 tmp = LOOPBACK_DISABLED; 2048 SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_LBM, 0); 2049 } 2050 SSP_WRITE_BITS(chip->cr1, SSP_DISABLED, SSP_CR1_MASK_SSE, 1); 2051 SSP_WRITE_BITS(chip->cr1, chip_info->hierarchy, SSP_CR1_MASK_MS, 2); 2052 SSP_WRITE_BITS(chip->cr1, chip_info->slave_tx_disable, SSP_CR1_MASK_SOD, 2053 3); 2054 2055 /* Save controller_state */ 2056 spi_set_ctldata(spi, chip); 2057 return status; 2058 err_config_params: 2059 spi_set_ctldata(spi, NULL); 2060 kfree(chip); 2061 return status; 2062 } 2063 2064 /** 2065 * pl022_cleanup - cleanup function registered to SPI master framework 2066 * @spi: spi device which is requesting cleanup 2067 * 2068 * This function is registered to the SPI framework for this SPI master 2069 * controller. It will free the runtime state of chip. 2070 */ 2071 static void pl022_cleanup(struct spi_device *spi) 2072 { 2073 struct chip_data *chip = spi_get_ctldata(spi); 2074 2075 spi_set_ctldata(spi, NULL); 2076 kfree(chip); 2077 } 2078 2079 static struct pl022_ssp_controller * 2080 pl022_platform_data_dt_get(struct device *dev) 2081 { 2082 struct device_node *np = dev->of_node; 2083 struct pl022_ssp_controller *pd; 2084 u32 tmp; 2085 2086 if (!np) { 2087 dev_err(dev, "no dt node defined\n"); 2088 return NULL; 2089 } 2090 2091 pd = devm_kzalloc(dev, sizeof(struct pl022_ssp_controller), GFP_KERNEL); 2092 if (!pd) 2093 return NULL; 2094 2095 pd->bus_id = -1; 2096 pd->enable_dma = 1; 2097 of_property_read_u32(np, "num-cs", &tmp); 2098 pd->num_chipselect = tmp; 2099 of_property_read_u32(np, "pl022,autosuspend-delay", 2100 &pd->autosuspend_delay); 2101 pd->rt = of_property_read_bool(np, "pl022,rt"); 2102 2103 return pd; 2104 } 2105 2106 static int pl022_probe(struct amba_device *adev, const struct amba_id *id) 2107 { 2108 struct device *dev = &adev->dev; 2109 struct pl022_ssp_controller *platform_info = 2110 dev_get_platdata(&adev->dev); 2111 struct spi_master *master; 2112 struct pl022 *pl022 = NULL; /*Data for this driver */ 2113 struct device_node *np = adev->dev.of_node; 2114 int status = 0, i, num_cs; 2115 2116 dev_info(&adev->dev, 2117 "ARM PL022 driver, device ID: 0x%08x\n", adev->periphid); 2118 if (!platform_info && IS_ENABLED(CONFIG_OF)) 2119 platform_info = pl022_platform_data_dt_get(dev); 2120 2121 if (!platform_info) { 2122 dev_err(dev, "probe: no platform data defined\n"); 2123 return -ENODEV; 2124 } 2125 2126 if (platform_info->num_chipselect) { 2127 num_cs = platform_info->num_chipselect; 2128 } else { 2129 dev_err(dev, "probe: no chip select defined\n"); 2130 return -ENODEV; 2131 } 2132 2133 /* Allocate master with space for data */ 2134 master = spi_alloc_master(dev, sizeof(struct pl022)); 2135 if (master == NULL) { 2136 dev_err(&adev->dev, "probe - cannot alloc SPI master\n"); 2137 return -ENOMEM; 2138 } 2139 2140 pl022 = spi_master_get_devdata(master); 2141 pl022->master = master; 2142 pl022->master_info = platform_info; 2143 pl022->adev = adev; 2144 pl022->vendor = id->data; 2145 pl022->chipselects = devm_kzalloc(dev, num_cs * sizeof(int), 2146 GFP_KERNEL); 2147 if (!pl022->chipselects) { 2148 status = -ENOMEM; 2149 goto err_no_mem; 2150 } 2151 2152 /* 2153 * Bus Number Which has been Assigned to this SSP controller 2154 * on this board 2155 */ 2156 master->bus_num = platform_info->bus_id; 2157 master->num_chipselect = num_cs; 2158 master->cleanup = pl022_cleanup; 2159 master->setup = pl022_setup; 2160 master->auto_runtime_pm = true; 2161 master->transfer_one_message = pl022_transfer_one_message; 2162 master->unprepare_transfer_hardware = pl022_unprepare_transfer_hardware; 2163 master->rt = platform_info->rt; 2164 master->dev.of_node = dev->of_node; 2165 2166 if (platform_info->num_chipselect && platform_info->chipselects) { 2167 for (i = 0; i < num_cs; i++) 2168 pl022->chipselects[i] = platform_info->chipselects[i]; 2169 } else if (pl022->vendor->internal_cs_ctrl) { 2170 for (i = 0; i < num_cs; i++) 2171 pl022->chipselects[i] = i; 2172 } else if (IS_ENABLED(CONFIG_OF)) { 2173 for (i = 0; i < num_cs; i++) { 2174 int cs_gpio = of_get_named_gpio(np, "cs-gpios", i); 2175 2176 if (cs_gpio == -EPROBE_DEFER) { 2177 status = -EPROBE_DEFER; 2178 goto err_no_gpio; 2179 } 2180 2181 pl022->chipselects[i] = cs_gpio; 2182 2183 if (gpio_is_valid(cs_gpio)) { 2184 if (devm_gpio_request(dev, cs_gpio, "ssp-pl022")) 2185 dev_err(&adev->dev, 2186 "could not request %d gpio\n", 2187 cs_gpio); 2188 else if (gpio_direction_output(cs_gpio, 1)) 2189 dev_err(&adev->dev, 2190 "could not set gpio %d as output\n", 2191 cs_gpio); 2192 } 2193 } 2194 } 2195 2196 /* 2197 * Supports mode 0-3, loopback, and active low CS. Transfers are 2198 * always MS bit first on the original pl022. 2199 */ 2200 master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP; 2201 if (pl022->vendor->extended_cr) 2202 master->mode_bits |= SPI_LSB_FIRST; 2203 2204 dev_dbg(&adev->dev, "BUSNO: %d\n", master->bus_num); 2205 2206 status = amba_request_regions(adev, NULL); 2207 if (status) 2208 goto err_no_ioregion; 2209 2210 pl022->phybase = adev->res.start; 2211 pl022->virtbase = devm_ioremap(dev, adev->res.start, 2212 resource_size(&adev->res)); 2213 if (pl022->virtbase == NULL) { 2214 status = -ENOMEM; 2215 goto err_no_ioremap; 2216 } 2217 dev_info(&adev->dev, "mapped registers from %pa to %p\n", 2218 &adev->res.start, pl022->virtbase); 2219 2220 pl022->clk = devm_clk_get(&adev->dev, NULL); 2221 if (IS_ERR(pl022->clk)) { 2222 status = PTR_ERR(pl022->clk); 2223 dev_err(&adev->dev, "could not retrieve SSP/SPI bus clock\n"); 2224 goto err_no_clk; 2225 } 2226 2227 status = clk_prepare_enable(pl022->clk); 2228 if (status) { 2229 dev_err(&adev->dev, "could not enable SSP/SPI bus clock\n"); 2230 goto err_no_clk_en; 2231 } 2232 2233 /* Initialize transfer pump */ 2234 tasklet_init(&pl022->pump_transfers, pump_transfers, 2235 (unsigned long)pl022); 2236 2237 /* Disable SSP */ 2238 writew((readw(SSP_CR1(pl022->virtbase)) & (~SSP_CR1_MASK_SSE)), 2239 SSP_CR1(pl022->virtbase)); 2240 load_ssp_default_config(pl022); 2241 2242 status = devm_request_irq(dev, adev->irq[0], pl022_interrupt_handler, 2243 0, "pl022", pl022); 2244 if (status < 0) { 2245 dev_err(&adev->dev, "probe - cannot get IRQ (%d)\n", status); 2246 goto err_no_irq; 2247 } 2248 2249 /* Get DMA channels, try autoconfiguration first */ 2250 status = pl022_dma_autoprobe(pl022); 2251 if (status == -EPROBE_DEFER) { 2252 dev_dbg(dev, "deferring probe to get DMA channel\n"); 2253 goto err_no_irq; 2254 } 2255 2256 /* If that failed, use channels from platform_info */ 2257 if (status == 0) 2258 platform_info->enable_dma = 1; 2259 else if (platform_info->enable_dma) { 2260 status = pl022_dma_probe(pl022); 2261 if (status != 0) 2262 platform_info->enable_dma = 0; 2263 } 2264 2265 /* Register with the SPI framework */ 2266 amba_set_drvdata(adev, pl022); 2267 status = devm_spi_register_master(&adev->dev, master); 2268 if (status != 0) { 2269 dev_err(&adev->dev, 2270 "probe - problem registering spi master\n"); 2271 goto err_spi_register; 2272 } 2273 dev_dbg(dev, "probe succeeded\n"); 2274 2275 /* let runtime pm put suspend */ 2276 if (platform_info->autosuspend_delay > 0) { 2277 dev_info(&adev->dev, 2278 "will use autosuspend for runtime pm, delay %dms\n", 2279 platform_info->autosuspend_delay); 2280 pm_runtime_set_autosuspend_delay(dev, 2281 platform_info->autosuspend_delay); 2282 pm_runtime_use_autosuspend(dev); 2283 } 2284 pm_runtime_put(dev); 2285 2286 return 0; 2287 2288 err_spi_register: 2289 if (platform_info->enable_dma) 2290 pl022_dma_remove(pl022); 2291 err_no_irq: 2292 clk_disable_unprepare(pl022->clk); 2293 err_no_clk_en: 2294 err_no_clk: 2295 err_no_ioremap: 2296 amba_release_regions(adev); 2297 err_no_ioregion: 2298 err_no_gpio: 2299 err_no_mem: 2300 spi_master_put(master); 2301 return status; 2302 } 2303 2304 static int 2305 pl022_remove(struct amba_device *adev) 2306 { 2307 struct pl022 *pl022 = amba_get_drvdata(adev); 2308 2309 if (!pl022) 2310 return 0; 2311 2312 /* 2313 * undo pm_runtime_put() in probe. I assume that we're not 2314 * accessing the primecell here. 2315 */ 2316 pm_runtime_get_noresume(&adev->dev); 2317 2318 load_ssp_default_config(pl022); 2319 if (pl022->master_info->enable_dma) 2320 pl022_dma_remove(pl022); 2321 2322 clk_disable_unprepare(pl022->clk); 2323 amba_release_regions(adev); 2324 tasklet_disable(&pl022->pump_transfers); 2325 return 0; 2326 } 2327 2328 #ifdef CONFIG_PM_SLEEP 2329 static int pl022_suspend(struct device *dev) 2330 { 2331 struct pl022 *pl022 = dev_get_drvdata(dev); 2332 int ret; 2333 2334 ret = spi_master_suspend(pl022->master); 2335 if (ret) { 2336 dev_warn(dev, "cannot suspend master\n"); 2337 return ret; 2338 } 2339 2340 ret = pm_runtime_force_suspend(dev); 2341 if (ret) { 2342 spi_master_resume(pl022->master); 2343 return ret; 2344 } 2345 2346 pinctrl_pm_select_sleep_state(dev); 2347 2348 dev_dbg(dev, "suspended\n"); 2349 return 0; 2350 } 2351 2352 static int pl022_resume(struct device *dev) 2353 { 2354 struct pl022 *pl022 = dev_get_drvdata(dev); 2355 int ret; 2356 2357 ret = pm_runtime_force_resume(dev); 2358 if (ret) 2359 dev_err(dev, "problem resuming\n"); 2360 2361 /* Start the queue running */ 2362 ret = spi_master_resume(pl022->master); 2363 if (ret) 2364 dev_err(dev, "problem starting queue (%d)\n", ret); 2365 else 2366 dev_dbg(dev, "resumed\n"); 2367 2368 return ret; 2369 } 2370 #endif 2371 2372 #ifdef CONFIG_PM 2373 static int pl022_runtime_suspend(struct device *dev) 2374 { 2375 struct pl022 *pl022 = dev_get_drvdata(dev); 2376 2377 clk_disable_unprepare(pl022->clk); 2378 pinctrl_pm_select_idle_state(dev); 2379 2380 return 0; 2381 } 2382 2383 static int pl022_runtime_resume(struct device *dev) 2384 { 2385 struct pl022 *pl022 = dev_get_drvdata(dev); 2386 2387 pinctrl_pm_select_default_state(dev); 2388 clk_prepare_enable(pl022->clk); 2389 2390 return 0; 2391 } 2392 #endif 2393 2394 static const struct dev_pm_ops pl022_dev_pm_ops = { 2395 SET_SYSTEM_SLEEP_PM_OPS(pl022_suspend, pl022_resume) 2396 SET_RUNTIME_PM_OPS(pl022_runtime_suspend, pl022_runtime_resume, NULL) 2397 }; 2398 2399 static struct vendor_data vendor_arm = { 2400 .fifodepth = 8, 2401 .max_bpw = 16, 2402 .unidir = false, 2403 .extended_cr = false, 2404 .pl023 = false, 2405 .loopback = true, 2406 .internal_cs_ctrl = false, 2407 }; 2408 2409 static struct vendor_data vendor_st = { 2410 .fifodepth = 32, 2411 .max_bpw = 32, 2412 .unidir = false, 2413 .extended_cr = true, 2414 .pl023 = false, 2415 .loopback = true, 2416 .internal_cs_ctrl = false, 2417 }; 2418 2419 static struct vendor_data vendor_st_pl023 = { 2420 .fifodepth = 32, 2421 .max_bpw = 32, 2422 .unidir = false, 2423 .extended_cr = true, 2424 .pl023 = true, 2425 .loopback = false, 2426 .internal_cs_ctrl = false, 2427 }; 2428 2429 static struct vendor_data vendor_lsi = { 2430 .fifodepth = 8, 2431 .max_bpw = 16, 2432 .unidir = false, 2433 .extended_cr = false, 2434 .pl023 = false, 2435 .loopback = true, 2436 .internal_cs_ctrl = true, 2437 }; 2438 2439 static struct amba_id pl022_ids[] = { 2440 { 2441 /* 2442 * ARM PL022 variant, this has a 16bit wide 2443 * and 8 locations deep TX/RX FIFO 2444 */ 2445 .id = 0x00041022, 2446 .mask = 0x000fffff, 2447 .data = &vendor_arm, 2448 }, 2449 { 2450 /* 2451 * ST Micro derivative, this has 32bit wide 2452 * and 32 locations deep TX/RX FIFO 2453 */ 2454 .id = 0x01080022, 2455 .mask = 0xffffffff, 2456 .data = &vendor_st, 2457 }, 2458 { 2459 /* 2460 * ST-Ericsson derivative "PL023" (this is not 2461 * an official ARM number), this is a PL022 SSP block 2462 * stripped to SPI mode only, it has 32bit wide 2463 * and 32 locations deep TX/RX FIFO but no extended 2464 * CR0/CR1 register 2465 */ 2466 .id = 0x00080023, 2467 .mask = 0xffffffff, 2468 .data = &vendor_st_pl023, 2469 }, 2470 { 2471 /* 2472 * PL022 variant that has a chip select control register whih 2473 * allows control of 5 output signals nCS[0:4]. 2474 */ 2475 .id = 0x000b6022, 2476 .mask = 0x000fffff, 2477 .data = &vendor_lsi, 2478 }, 2479 { 0, 0 }, 2480 }; 2481 2482 MODULE_DEVICE_TABLE(amba, pl022_ids); 2483 2484 static struct amba_driver pl022_driver = { 2485 .drv = { 2486 .name = "ssp-pl022", 2487 .pm = &pl022_dev_pm_ops, 2488 }, 2489 .id_table = pl022_ids, 2490 .probe = pl022_probe, 2491 .remove = pl022_remove, 2492 }; 2493 2494 static int __init pl022_init(void) 2495 { 2496 return amba_driver_register(&pl022_driver); 2497 } 2498 subsys_initcall(pl022_init); 2499 2500 static void __exit pl022_exit(void) 2501 { 2502 amba_driver_unregister(&pl022_driver); 2503 } 2504 module_exit(pl022_exit); 2505 2506 MODULE_AUTHOR("Linus Walleij <linus.walleij@stericsson.com>"); 2507 MODULE_DESCRIPTION("PL022 SSP Controller Driver"); 2508 MODULE_LICENSE("GPL"); 2509