1 /* 2 * A driver for the ARM PL022 PrimeCell SSP/SPI bus master. 3 * 4 * Copyright (C) 2008-2012 ST-Ericsson AB 5 * Copyright (C) 2006 STMicroelectronics Pvt. Ltd. 6 * 7 * Author: Linus Walleij <linus.walleij@stericsson.com> 8 * 9 * Initial version inspired by: 10 * linux-2.6.17-rc3-mm1/drivers/spi/pxa2xx_spi.c 11 * Initial adoption to PL022 by: 12 * Sachin Verma <sachin.verma@st.com> 13 * 14 * This program is free software; you can redistribute it and/or modify 15 * it under the terms of the GNU General Public License as published by 16 * the Free Software Foundation; either version 2 of the License, or 17 * (at your option) any later version. 18 * 19 * This program is distributed in the hope that it will be useful, 20 * but WITHOUT ANY WARRANTY; without even the implied warranty of 21 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 22 * GNU General Public License for more details. 23 */ 24 25 #include <linux/init.h> 26 #include <linux/module.h> 27 #include <linux/device.h> 28 #include <linux/ioport.h> 29 #include <linux/errno.h> 30 #include <linux/interrupt.h> 31 #include <linux/spi/spi.h> 32 #include <linux/delay.h> 33 #include <linux/clk.h> 34 #include <linux/err.h> 35 #include <linux/amba/bus.h> 36 #include <linux/amba/pl022.h> 37 #include <linux/io.h> 38 #include <linux/slab.h> 39 #include <linux/dmaengine.h> 40 #include <linux/dma-mapping.h> 41 #include <linux/scatterlist.h> 42 #include <linux/pm_runtime.h> 43 #include <linux/gpio.h> 44 #include <linux/of_gpio.h> 45 #include <linux/pinctrl/consumer.h> 46 47 /* 48 * This macro is used to define some register default values. 49 * reg is masked with mask, the OR:ed with an (again masked) 50 * val shifted sb steps to the left. 51 */ 52 #define SSP_WRITE_BITS(reg, val, mask, sb) \ 53 ((reg) = (((reg) & ~(mask)) | (((val)<<(sb)) & (mask)))) 54 55 /* 56 * This macro is also used to define some default values. 57 * It will just shift val by sb steps to the left and mask 58 * the result with mask. 59 */ 60 #define GEN_MASK_BITS(val, mask, sb) \ 61 (((val)<<(sb)) & (mask)) 62 63 #define DRIVE_TX 0 64 #define DO_NOT_DRIVE_TX 1 65 66 #define DO_NOT_QUEUE_DMA 0 67 #define QUEUE_DMA 1 68 69 #define RX_TRANSFER 1 70 #define TX_TRANSFER 2 71 72 /* 73 * Macros to access SSP Registers with their offsets 74 */ 75 #define SSP_CR0(r) (r + 0x000) 76 #define SSP_CR1(r) (r + 0x004) 77 #define SSP_DR(r) (r + 0x008) 78 #define SSP_SR(r) (r + 0x00C) 79 #define SSP_CPSR(r) (r + 0x010) 80 #define SSP_IMSC(r) (r + 0x014) 81 #define SSP_RIS(r) (r + 0x018) 82 #define SSP_MIS(r) (r + 0x01C) 83 #define SSP_ICR(r) (r + 0x020) 84 #define SSP_DMACR(r) (r + 0x024) 85 #define SSP_CSR(r) (r + 0x030) /* vendor extension */ 86 #define SSP_ITCR(r) (r + 0x080) 87 #define SSP_ITIP(r) (r + 0x084) 88 #define SSP_ITOP(r) (r + 0x088) 89 #define SSP_TDR(r) (r + 0x08C) 90 91 #define SSP_PID0(r) (r + 0xFE0) 92 #define SSP_PID1(r) (r + 0xFE4) 93 #define SSP_PID2(r) (r + 0xFE8) 94 #define SSP_PID3(r) (r + 0xFEC) 95 96 #define SSP_CID0(r) (r + 0xFF0) 97 #define SSP_CID1(r) (r + 0xFF4) 98 #define SSP_CID2(r) (r + 0xFF8) 99 #define SSP_CID3(r) (r + 0xFFC) 100 101 /* 102 * SSP Control Register 0 - SSP_CR0 103 */ 104 #define SSP_CR0_MASK_DSS (0x0FUL << 0) 105 #define SSP_CR0_MASK_FRF (0x3UL << 4) 106 #define SSP_CR0_MASK_SPO (0x1UL << 6) 107 #define SSP_CR0_MASK_SPH (0x1UL << 7) 108 #define SSP_CR0_MASK_SCR (0xFFUL << 8) 109 110 /* 111 * The ST version of this block moves som bits 112 * in SSP_CR0 and extends it to 32 bits 113 */ 114 #define SSP_CR0_MASK_DSS_ST (0x1FUL << 0) 115 #define SSP_CR0_MASK_HALFDUP_ST (0x1UL << 5) 116 #define SSP_CR0_MASK_CSS_ST (0x1FUL << 16) 117 #define SSP_CR0_MASK_FRF_ST (0x3UL << 21) 118 119 /* 120 * SSP Control Register 0 - SSP_CR1 121 */ 122 #define SSP_CR1_MASK_LBM (0x1UL << 0) 123 #define SSP_CR1_MASK_SSE (0x1UL << 1) 124 #define SSP_CR1_MASK_MS (0x1UL << 2) 125 #define SSP_CR1_MASK_SOD (0x1UL << 3) 126 127 /* 128 * The ST version of this block adds some bits 129 * in SSP_CR1 130 */ 131 #define SSP_CR1_MASK_RENDN_ST (0x1UL << 4) 132 #define SSP_CR1_MASK_TENDN_ST (0x1UL << 5) 133 #define SSP_CR1_MASK_MWAIT_ST (0x1UL << 6) 134 #define SSP_CR1_MASK_RXIFLSEL_ST (0x7UL << 7) 135 #define SSP_CR1_MASK_TXIFLSEL_ST (0x7UL << 10) 136 /* This one is only in the PL023 variant */ 137 #define SSP_CR1_MASK_FBCLKDEL_ST (0x7UL << 13) 138 139 /* 140 * SSP Status Register - SSP_SR 141 */ 142 #define SSP_SR_MASK_TFE (0x1UL << 0) /* Transmit FIFO empty */ 143 #define SSP_SR_MASK_TNF (0x1UL << 1) /* Transmit FIFO not full */ 144 #define SSP_SR_MASK_RNE (0x1UL << 2) /* Receive FIFO not empty */ 145 #define SSP_SR_MASK_RFF (0x1UL << 3) /* Receive FIFO full */ 146 #define SSP_SR_MASK_BSY (0x1UL << 4) /* Busy Flag */ 147 148 /* 149 * SSP Clock Prescale Register - SSP_CPSR 150 */ 151 #define SSP_CPSR_MASK_CPSDVSR (0xFFUL << 0) 152 153 /* 154 * SSP Interrupt Mask Set/Clear Register - SSP_IMSC 155 */ 156 #define SSP_IMSC_MASK_RORIM (0x1UL << 0) /* Receive Overrun Interrupt mask */ 157 #define SSP_IMSC_MASK_RTIM (0x1UL << 1) /* Receive timeout Interrupt mask */ 158 #define SSP_IMSC_MASK_RXIM (0x1UL << 2) /* Receive FIFO Interrupt mask */ 159 #define SSP_IMSC_MASK_TXIM (0x1UL << 3) /* Transmit FIFO Interrupt mask */ 160 161 /* 162 * SSP Raw Interrupt Status Register - SSP_RIS 163 */ 164 /* Receive Overrun Raw Interrupt status */ 165 #define SSP_RIS_MASK_RORRIS (0x1UL << 0) 166 /* Receive Timeout Raw Interrupt status */ 167 #define SSP_RIS_MASK_RTRIS (0x1UL << 1) 168 /* Receive FIFO Raw Interrupt status */ 169 #define SSP_RIS_MASK_RXRIS (0x1UL << 2) 170 /* Transmit FIFO Raw Interrupt status */ 171 #define SSP_RIS_MASK_TXRIS (0x1UL << 3) 172 173 /* 174 * SSP Masked Interrupt Status Register - SSP_MIS 175 */ 176 /* Receive Overrun Masked Interrupt status */ 177 #define SSP_MIS_MASK_RORMIS (0x1UL << 0) 178 /* Receive Timeout Masked Interrupt status */ 179 #define SSP_MIS_MASK_RTMIS (0x1UL << 1) 180 /* Receive FIFO Masked Interrupt status */ 181 #define SSP_MIS_MASK_RXMIS (0x1UL << 2) 182 /* Transmit FIFO Masked Interrupt status */ 183 #define SSP_MIS_MASK_TXMIS (0x1UL << 3) 184 185 /* 186 * SSP Interrupt Clear Register - SSP_ICR 187 */ 188 /* Receive Overrun Raw Clear Interrupt bit */ 189 #define SSP_ICR_MASK_RORIC (0x1UL << 0) 190 /* Receive Timeout Clear Interrupt bit */ 191 #define SSP_ICR_MASK_RTIC (0x1UL << 1) 192 193 /* 194 * SSP DMA Control Register - SSP_DMACR 195 */ 196 /* Receive DMA Enable bit */ 197 #define SSP_DMACR_MASK_RXDMAE (0x1UL << 0) 198 /* Transmit DMA Enable bit */ 199 #define SSP_DMACR_MASK_TXDMAE (0x1UL << 1) 200 201 /* 202 * SSP Chip Select Control Register - SSP_CSR 203 * (vendor extension) 204 */ 205 #define SSP_CSR_CSVALUE_MASK (0x1FUL << 0) 206 207 /* 208 * SSP Integration Test control Register - SSP_ITCR 209 */ 210 #define SSP_ITCR_MASK_ITEN (0x1UL << 0) 211 #define SSP_ITCR_MASK_TESTFIFO (0x1UL << 1) 212 213 /* 214 * SSP Integration Test Input Register - SSP_ITIP 215 */ 216 #define ITIP_MASK_SSPRXD (0x1UL << 0) 217 #define ITIP_MASK_SSPFSSIN (0x1UL << 1) 218 #define ITIP_MASK_SSPCLKIN (0x1UL << 2) 219 #define ITIP_MASK_RXDMAC (0x1UL << 3) 220 #define ITIP_MASK_TXDMAC (0x1UL << 4) 221 #define ITIP_MASK_SSPTXDIN (0x1UL << 5) 222 223 /* 224 * SSP Integration Test output Register - SSP_ITOP 225 */ 226 #define ITOP_MASK_SSPTXD (0x1UL << 0) 227 #define ITOP_MASK_SSPFSSOUT (0x1UL << 1) 228 #define ITOP_MASK_SSPCLKOUT (0x1UL << 2) 229 #define ITOP_MASK_SSPOEn (0x1UL << 3) 230 #define ITOP_MASK_SSPCTLOEn (0x1UL << 4) 231 #define ITOP_MASK_RORINTR (0x1UL << 5) 232 #define ITOP_MASK_RTINTR (0x1UL << 6) 233 #define ITOP_MASK_RXINTR (0x1UL << 7) 234 #define ITOP_MASK_TXINTR (0x1UL << 8) 235 #define ITOP_MASK_INTR (0x1UL << 9) 236 #define ITOP_MASK_RXDMABREQ (0x1UL << 10) 237 #define ITOP_MASK_RXDMASREQ (0x1UL << 11) 238 #define ITOP_MASK_TXDMABREQ (0x1UL << 12) 239 #define ITOP_MASK_TXDMASREQ (0x1UL << 13) 240 241 /* 242 * SSP Test Data Register - SSP_TDR 243 */ 244 #define TDR_MASK_TESTDATA (0xFFFFFFFF) 245 246 /* 247 * Message State 248 * we use the spi_message.state (void *) pointer to 249 * hold a single state value, that's why all this 250 * (void *) casting is done here. 251 */ 252 #define STATE_START ((void *) 0) 253 #define STATE_RUNNING ((void *) 1) 254 #define STATE_DONE ((void *) 2) 255 #define STATE_ERROR ((void *) -1) 256 257 /* 258 * SSP State - Whether Enabled or Disabled 259 */ 260 #define SSP_DISABLED (0) 261 #define SSP_ENABLED (1) 262 263 /* 264 * SSP DMA State - Whether DMA Enabled or Disabled 265 */ 266 #define SSP_DMA_DISABLED (0) 267 #define SSP_DMA_ENABLED (1) 268 269 /* 270 * SSP Clock Defaults 271 */ 272 #define SSP_DEFAULT_CLKRATE 0x2 273 #define SSP_DEFAULT_PRESCALE 0x40 274 275 /* 276 * SSP Clock Parameter ranges 277 */ 278 #define CPSDVR_MIN 0x02 279 #define CPSDVR_MAX 0xFE 280 #define SCR_MIN 0x00 281 #define SCR_MAX 0xFF 282 283 /* 284 * SSP Interrupt related Macros 285 */ 286 #define DEFAULT_SSP_REG_IMSC 0x0UL 287 #define DISABLE_ALL_INTERRUPTS DEFAULT_SSP_REG_IMSC 288 #define ENABLE_ALL_INTERRUPTS (~DEFAULT_SSP_REG_IMSC) 289 290 #define CLEAR_ALL_INTERRUPTS 0x3 291 292 #define SPI_POLLING_TIMEOUT 1000 293 294 /* 295 * The type of reading going on on this chip 296 */ 297 enum ssp_reading { 298 READING_NULL, 299 READING_U8, 300 READING_U16, 301 READING_U32 302 }; 303 304 /** 305 * The type of writing going on on this chip 306 */ 307 enum ssp_writing { 308 WRITING_NULL, 309 WRITING_U8, 310 WRITING_U16, 311 WRITING_U32 312 }; 313 314 /** 315 * struct vendor_data - vendor-specific config parameters 316 * for PL022 derivates 317 * @fifodepth: depth of FIFOs (both) 318 * @max_bpw: maximum number of bits per word 319 * @unidir: supports unidirection transfers 320 * @extended_cr: 32 bit wide control register 0 with extra 321 * features and extra features in CR1 as found in the ST variants 322 * @pl023: supports a subset of the ST extensions called "PL023" 323 * @internal_cs_ctrl: supports chip select control register 324 */ 325 struct vendor_data { 326 int fifodepth; 327 int max_bpw; 328 bool unidir; 329 bool extended_cr; 330 bool pl023; 331 bool loopback; 332 bool internal_cs_ctrl; 333 }; 334 335 /** 336 * struct pl022 - This is the private SSP driver data structure 337 * @adev: AMBA device model hookup 338 * @vendor: vendor data for the IP block 339 * @phybase: the physical memory where the SSP device resides 340 * @virtbase: the virtual memory where the SSP is mapped 341 * @clk: outgoing clock "SPICLK" for the SPI bus 342 * @master: SPI framework hookup 343 * @master_info: controller-specific data from machine setup 344 * @kworker: thread struct for message pump 345 * @kworker_task: pointer to task for message pump kworker thread 346 * @pump_messages: work struct for scheduling work to the message pump 347 * @queue_lock: spinlock to syncronise access to message queue 348 * @queue: message queue 349 * @busy: message pump is busy 350 * @running: message pump is running 351 * @pump_transfers: Tasklet used in Interrupt Transfer mode 352 * @cur_msg: Pointer to current spi_message being processed 353 * @cur_transfer: Pointer to current spi_transfer 354 * @cur_chip: pointer to current clients chip(assigned from controller_state) 355 * @next_msg_cs_active: the next message in the queue has been examined 356 * and it was found that it uses the same chip select as the previous 357 * message, so we left it active after the previous transfer, and it's 358 * active already. 359 * @tx: current position in TX buffer to be read 360 * @tx_end: end position in TX buffer to be read 361 * @rx: current position in RX buffer to be written 362 * @rx_end: end position in RX buffer to be written 363 * @read: the type of read currently going on 364 * @write: the type of write currently going on 365 * @exp_fifo_level: expected FIFO level 366 * @dma_rx_channel: optional channel for RX DMA 367 * @dma_tx_channel: optional channel for TX DMA 368 * @sgt_rx: scattertable for the RX transfer 369 * @sgt_tx: scattertable for the TX transfer 370 * @dummypage: a dummy page used for driving data on the bus with DMA 371 * @cur_cs: current chip select (gpio) 372 * @chipselects: list of chipselects (gpios) 373 */ 374 struct pl022 { 375 struct amba_device *adev; 376 struct vendor_data *vendor; 377 resource_size_t phybase; 378 void __iomem *virtbase; 379 struct clk *clk; 380 struct spi_master *master; 381 struct pl022_ssp_controller *master_info; 382 /* Message per-transfer pump */ 383 struct tasklet_struct pump_transfers; 384 struct spi_message *cur_msg; 385 struct spi_transfer *cur_transfer; 386 struct chip_data *cur_chip; 387 bool next_msg_cs_active; 388 void *tx; 389 void *tx_end; 390 void *rx; 391 void *rx_end; 392 enum ssp_reading read; 393 enum ssp_writing write; 394 u32 exp_fifo_level; 395 enum ssp_rx_level_trig rx_lev_trig; 396 enum ssp_tx_level_trig tx_lev_trig; 397 /* DMA settings */ 398 #ifdef CONFIG_DMA_ENGINE 399 struct dma_chan *dma_rx_channel; 400 struct dma_chan *dma_tx_channel; 401 struct sg_table sgt_rx; 402 struct sg_table sgt_tx; 403 char *dummypage; 404 bool dma_running; 405 #endif 406 int cur_cs; 407 int *chipselects; 408 }; 409 410 /** 411 * struct chip_data - To maintain runtime state of SSP for each client chip 412 * @cr0: Value of control register CR0 of SSP - on later ST variants this 413 * register is 32 bits wide rather than just 16 414 * @cr1: Value of control register CR1 of SSP 415 * @dmacr: Value of DMA control Register of SSP 416 * @cpsr: Value of Clock prescale register 417 * @n_bytes: how many bytes(power of 2) reqd for a given data width of client 418 * @enable_dma: Whether to enable DMA or not 419 * @read: function ptr to be used to read when doing xfer for this chip 420 * @write: function ptr to be used to write when doing xfer for this chip 421 * @cs_control: chip select callback provided by chip 422 * @xfer_type: polling/interrupt/DMA 423 * 424 * Runtime state of the SSP controller, maintained per chip, 425 * This would be set according to the current message that would be served 426 */ 427 struct chip_data { 428 u32 cr0; 429 u16 cr1; 430 u16 dmacr; 431 u16 cpsr; 432 u8 n_bytes; 433 bool enable_dma; 434 enum ssp_reading read; 435 enum ssp_writing write; 436 void (*cs_control) (u32 command); 437 int xfer_type; 438 }; 439 440 /** 441 * null_cs_control - Dummy chip select function 442 * @command: select/delect the chip 443 * 444 * If no chip select function is provided by client this is used as dummy 445 * chip select 446 */ 447 static void null_cs_control(u32 command) 448 { 449 pr_debug("pl022: dummy chip select control, CS=0x%x\n", command); 450 } 451 452 /** 453 * internal_cs_control - Control chip select signals via SSP_CSR. 454 * @pl022: SSP driver private data structure 455 * @command: select/delect the chip 456 * 457 * Used on controller with internal chip select control via SSP_CSR register 458 * (vendor extension). Each of the 5 LSB in the register controls one chip 459 * select signal. 460 */ 461 static void internal_cs_control(struct pl022 *pl022, u32 command) 462 { 463 u32 tmp; 464 465 tmp = readw(SSP_CSR(pl022->virtbase)); 466 if (command == SSP_CHIP_SELECT) 467 tmp &= ~BIT(pl022->cur_cs); 468 else 469 tmp |= BIT(pl022->cur_cs); 470 writew(tmp, SSP_CSR(pl022->virtbase)); 471 } 472 473 static void pl022_cs_control(struct pl022 *pl022, u32 command) 474 { 475 if (pl022->vendor->internal_cs_ctrl) 476 internal_cs_control(pl022, command); 477 else if (gpio_is_valid(pl022->cur_cs)) 478 gpio_set_value(pl022->cur_cs, command); 479 else 480 pl022->cur_chip->cs_control(command); 481 } 482 483 /** 484 * giveback - current spi_message is over, schedule next message and call 485 * callback of this message. Assumes that caller already 486 * set message->status; dma and pio irqs are blocked 487 * @pl022: SSP driver private data structure 488 */ 489 static void giveback(struct pl022 *pl022) 490 { 491 struct spi_transfer *last_transfer; 492 pl022->next_msg_cs_active = false; 493 494 last_transfer = list_last_entry(&pl022->cur_msg->transfers, 495 struct spi_transfer, transfer_list); 496 497 /* Delay if requested before any change in chip select */ 498 if (last_transfer->delay_usecs) 499 /* 500 * FIXME: This runs in interrupt context. 501 * Is this really smart? 502 */ 503 udelay(last_transfer->delay_usecs); 504 505 if (!last_transfer->cs_change) { 506 struct spi_message *next_msg; 507 508 /* 509 * cs_change was not set. We can keep the chip select 510 * enabled if there is message in the queue and it is 511 * for the same spi device. 512 * 513 * We cannot postpone this until pump_messages, because 514 * after calling msg->complete (below) the driver that 515 * sent the current message could be unloaded, which 516 * could invalidate the cs_control() callback... 517 */ 518 /* get a pointer to the next message, if any */ 519 next_msg = spi_get_next_queued_message(pl022->master); 520 521 /* 522 * see if the next and current messages point 523 * to the same spi device. 524 */ 525 if (next_msg && next_msg->spi != pl022->cur_msg->spi) 526 next_msg = NULL; 527 if (!next_msg || pl022->cur_msg->state == STATE_ERROR) 528 pl022_cs_control(pl022, SSP_CHIP_DESELECT); 529 else 530 pl022->next_msg_cs_active = true; 531 532 } 533 534 pl022->cur_msg = NULL; 535 pl022->cur_transfer = NULL; 536 pl022->cur_chip = NULL; 537 538 /* disable the SPI/SSP operation */ 539 writew((readw(SSP_CR1(pl022->virtbase)) & 540 (~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase)); 541 542 spi_finalize_current_message(pl022->master); 543 } 544 545 /** 546 * flush - flush the FIFO to reach a clean state 547 * @pl022: SSP driver private data structure 548 */ 549 static int flush(struct pl022 *pl022) 550 { 551 unsigned long limit = loops_per_jiffy << 1; 552 553 dev_dbg(&pl022->adev->dev, "flush\n"); 554 do { 555 while (readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RNE) 556 readw(SSP_DR(pl022->virtbase)); 557 } while ((readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_BSY) && limit--); 558 559 pl022->exp_fifo_level = 0; 560 561 return limit; 562 } 563 564 /** 565 * restore_state - Load configuration of current chip 566 * @pl022: SSP driver private data structure 567 */ 568 static void restore_state(struct pl022 *pl022) 569 { 570 struct chip_data *chip = pl022->cur_chip; 571 572 if (pl022->vendor->extended_cr) 573 writel(chip->cr0, SSP_CR0(pl022->virtbase)); 574 else 575 writew(chip->cr0, SSP_CR0(pl022->virtbase)); 576 writew(chip->cr1, SSP_CR1(pl022->virtbase)); 577 writew(chip->dmacr, SSP_DMACR(pl022->virtbase)); 578 writew(chip->cpsr, SSP_CPSR(pl022->virtbase)); 579 writew(DISABLE_ALL_INTERRUPTS, SSP_IMSC(pl022->virtbase)); 580 writew(CLEAR_ALL_INTERRUPTS, SSP_ICR(pl022->virtbase)); 581 } 582 583 /* 584 * Default SSP Register Values 585 */ 586 #define DEFAULT_SSP_REG_CR0 ( \ 587 GEN_MASK_BITS(SSP_DATA_BITS_12, SSP_CR0_MASK_DSS, 0) | \ 588 GEN_MASK_BITS(SSP_INTERFACE_MOTOROLA_SPI, SSP_CR0_MASK_FRF, 4) | \ 589 GEN_MASK_BITS(SSP_CLK_POL_IDLE_LOW, SSP_CR0_MASK_SPO, 6) | \ 590 GEN_MASK_BITS(SSP_CLK_SECOND_EDGE, SSP_CR0_MASK_SPH, 7) | \ 591 GEN_MASK_BITS(SSP_DEFAULT_CLKRATE, SSP_CR0_MASK_SCR, 8) \ 592 ) 593 594 /* ST versions have slightly different bit layout */ 595 #define DEFAULT_SSP_REG_CR0_ST ( \ 596 GEN_MASK_BITS(SSP_DATA_BITS_12, SSP_CR0_MASK_DSS_ST, 0) | \ 597 GEN_MASK_BITS(SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, SSP_CR0_MASK_HALFDUP_ST, 5) | \ 598 GEN_MASK_BITS(SSP_CLK_POL_IDLE_LOW, SSP_CR0_MASK_SPO, 6) | \ 599 GEN_MASK_BITS(SSP_CLK_SECOND_EDGE, SSP_CR0_MASK_SPH, 7) | \ 600 GEN_MASK_BITS(SSP_DEFAULT_CLKRATE, SSP_CR0_MASK_SCR, 8) | \ 601 GEN_MASK_BITS(SSP_BITS_8, SSP_CR0_MASK_CSS_ST, 16) | \ 602 GEN_MASK_BITS(SSP_INTERFACE_MOTOROLA_SPI, SSP_CR0_MASK_FRF_ST, 21) \ 603 ) 604 605 /* The PL023 version is slightly different again */ 606 #define DEFAULT_SSP_REG_CR0_ST_PL023 ( \ 607 GEN_MASK_BITS(SSP_DATA_BITS_12, SSP_CR0_MASK_DSS_ST, 0) | \ 608 GEN_MASK_BITS(SSP_CLK_POL_IDLE_LOW, SSP_CR0_MASK_SPO, 6) | \ 609 GEN_MASK_BITS(SSP_CLK_SECOND_EDGE, SSP_CR0_MASK_SPH, 7) | \ 610 GEN_MASK_BITS(SSP_DEFAULT_CLKRATE, SSP_CR0_MASK_SCR, 8) \ 611 ) 612 613 #define DEFAULT_SSP_REG_CR1 ( \ 614 GEN_MASK_BITS(LOOPBACK_DISABLED, SSP_CR1_MASK_LBM, 0) | \ 615 GEN_MASK_BITS(SSP_DISABLED, SSP_CR1_MASK_SSE, 1) | \ 616 GEN_MASK_BITS(SSP_MASTER, SSP_CR1_MASK_MS, 2) | \ 617 GEN_MASK_BITS(DO_NOT_DRIVE_TX, SSP_CR1_MASK_SOD, 3) \ 618 ) 619 620 /* ST versions extend this register to use all 16 bits */ 621 #define DEFAULT_SSP_REG_CR1_ST ( \ 622 DEFAULT_SSP_REG_CR1 | \ 623 GEN_MASK_BITS(SSP_RX_MSB, SSP_CR1_MASK_RENDN_ST, 4) | \ 624 GEN_MASK_BITS(SSP_TX_MSB, SSP_CR1_MASK_TENDN_ST, 5) | \ 625 GEN_MASK_BITS(SSP_MWIRE_WAIT_ZERO, SSP_CR1_MASK_MWAIT_ST, 6) |\ 626 GEN_MASK_BITS(SSP_RX_1_OR_MORE_ELEM, SSP_CR1_MASK_RXIFLSEL_ST, 7) | \ 627 GEN_MASK_BITS(SSP_TX_1_OR_MORE_EMPTY_LOC, SSP_CR1_MASK_TXIFLSEL_ST, 10) \ 628 ) 629 630 /* 631 * The PL023 variant has further differences: no loopback mode, no microwire 632 * support, and a new clock feedback delay setting. 633 */ 634 #define DEFAULT_SSP_REG_CR1_ST_PL023 ( \ 635 GEN_MASK_BITS(SSP_DISABLED, SSP_CR1_MASK_SSE, 1) | \ 636 GEN_MASK_BITS(SSP_MASTER, SSP_CR1_MASK_MS, 2) | \ 637 GEN_MASK_BITS(DO_NOT_DRIVE_TX, SSP_CR1_MASK_SOD, 3) | \ 638 GEN_MASK_BITS(SSP_RX_MSB, SSP_CR1_MASK_RENDN_ST, 4) | \ 639 GEN_MASK_BITS(SSP_TX_MSB, SSP_CR1_MASK_TENDN_ST, 5) | \ 640 GEN_MASK_BITS(SSP_RX_1_OR_MORE_ELEM, SSP_CR1_MASK_RXIFLSEL_ST, 7) | \ 641 GEN_MASK_BITS(SSP_TX_1_OR_MORE_EMPTY_LOC, SSP_CR1_MASK_TXIFLSEL_ST, 10) | \ 642 GEN_MASK_BITS(SSP_FEEDBACK_CLK_DELAY_NONE, SSP_CR1_MASK_FBCLKDEL_ST, 13) \ 643 ) 644 645 #define DEFAULT_SSP_REG_CPSR ( \ 646 GEN_MASK_BITS(SSP_DEFAULT_PRESCALE, SSP_CPSR_MASK_CPSDVSR, 0) \ 647 ) 648 649 #define DEFAULT_SSP_REG_DMACR (\ 650 GEN_MASK_BITS(SSP_DMA_DISABLED, SSP_DMACR_MASK_RXDMAE, 0) | \ 651 GEN_MASK_BITS(SSP_DMA_DISABLED, SSP_DMACR_MASK_TXDMAE, 1) \ 652 ) 653 654 /** 655 * load_ssp_default_config - Load default configuration for SSP 656 * @pl022: SSP driver private data structure 657 */ 658 static void load_ssp_default_config(struct pl022 *pl022) 659 { 660 if (pl022->vendor->pl023) { 661 writel(DEFAULT_SSP_REG_CR0_ST_PL023, SSP_CR0(pl022->virtbase)); 662 writew(DEFAULT_SSP_REG_CR1_ST_PL023, SSP_CR1(pl022->virtbase)); 663 } else if (pl022->vendor->extended_cr) { 664 writel(DEFAULT_SSP_REG_CR0_ST, SSP_CR0(pl022->virtbase)); 665 writew(DEFAULT_SSP_REG_CR1_ST, SSP_CR1(pl022->virtbase)); 666 } else { 667 writew(DEFAULT_SSP_REG_CR0, SSP_CR0(pl022->virtbase)); 668 writew(DEFAULT_SSP_REG_CR1, SSP_CR1(pl022->virtbase)); 669 } 670 writew(DEFAULT_SSP_REG_DMACR, SSP_DMACR(pl022->virtbase)); 671 writew(DEFAULT_SSP_REG_CPSR, SSP_CPSR(pl022->virtbase)); 672 writew(DISABLE_ALL_INTERRUPTS, SSP_IMSC(pl022->virtbase)); 673 writew(CLEAR_ALL_INTERRUPTS, SSP_ICR(pl022->virtbase)); 674 } 675 676 /** 677 * This will write to TX and read from RX according to the parameters 678 * set in pl022. 679 */ 680 static void readwriter(struct pl022 *pl022) 681 { 682 683 /* 684 * The FIFO depth is different between primecell variants. 685 * I believe filling in too much in the FIFO might cause 686 * errons in 8bit wide transfers on ARM variants (just 8 words 687 * FIFO, means only 8x8 = 64 bits in FIFO) at least. 688 * 689 * To prevent this issue, the TX FIFO is only filled to the 690 * unused RX FIFO fill length, regardless of what the TX 691 * FIFO status flag indicates. 692 */ 693 dev_dbg(&pl022->adev->dev, 694 "%s, rx: %p, rxend: %p, tx: %p, txend: %p\n", 695 __func__, pl022->rx, pl022->rx_end, pl022->tx, pl022->tx_end); 696 697 /* Read as much as you can */ 698 while ((readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RNE) 699 && (pl022->rx < pl022->rx_end)) { 700 switch (pl022->read) { 701 case READING_NULL: 702 readw(SSP_DR(pl022->virtbase)); 703 break; 704 case READING_U8: 705 *(u8 *) (pl022->rx) = 706 readw(SSP_DR(pl022->virtbase)) & 0xFFU; 707 break; 708 case READING_U16: 709 *(u16 *) (pl022->rx) = 710 (u16) readw(SSP_DR(pl022->virtbase)); 711 break; 712 case READING_U32: 713 *(u32 *) (pl022->rx) = 714 readl(SSP_DR(pl022->virtbase)); 715 break; 716 } 717 pl022->rx += (pl022->cur_chip->n_bytes); 718 pl022->exp_fifo_level--; 719 } 720 /* 721 * Write as much as possible up to the RX FIFO size 722 */ 723 while ((pl022->exp_fifo_level < pl022->vendor->fifodepth) 724 && (pl022->tx < pl022->tx_end)) { 725 switch (pl022->write) { 726 case WRITING_NULL: 727 writew(0x0, SSP_DR(pl022->virtbase)); 728 break; 729 case WRITING_U8: 730 writew(*(u8 *) (pl022->tx), SSP_DR(pl022->virtbase)); 731 break; 732 case WRITING_U16: 733 writew((*(u16 *) (pl022->tx)), SSP_DR(pl022->virtbase)); 734 break; 735 case WRITING_U32: 736 writel(*(u32 *) (pl022->tx), SSP_DR(pl022->virtbase)); 737 break; 738 } 739 pl022->tx += (pl022->cur_chip->n_bytes); 740 pl022->exp_fifo_level++; 741 /* 742 * This inner reader takes care of things appearing in the RX 743 * FIFO as we're transmitting. This will happen a lot since the 744 * clock starts running when you put things into the TX FIFO, 745 * and then things are continuously clocked into the RX FIFO. 746 */ 747 while ((readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RNE) 748 && (pl022->rx < pl022->rx_end)) { 749 switch (pl022->read) { 750 case READING_NULL: 751 readw(SSP_DR(pl022->virtbase)); 752 break; 753 case READING_U8: 754 *(u8 *) (pl022->rx) = 755 readw(SSP_DR(pl022->virtbase)) & 0xFFU; 756 break; 757 case READING_U16: 758 *(u16 *) (pl022->rx) = 759 (u16) readw(SSP_DR(pl022->virtbase)); 760 break; 761 case READING_U32: 762 *(u32 *) (pl022->rx) = 763 readl(SSP_DR(pl022->virtbase)); 764 break; 765 } 766 pl022->rx += (pl022->cur_chip->n_bytes); 767 pl022->exp_fifo_level--; 768 } 769 } 770 /* 771 * When we exit here the TX FIFO should be full and the RX FIFO 772 * should be empty 773 */ 774 } 775 776 /** 777 * next_transfer - Move to the Next transfer in the current spi message 778 * @pl022: SSP driver private data structure 779 * 780 * This function moves though the linked list of spi transfers in the 781 * current spi message and returns with the state of current spi 782 * message i.e whether its last transfer is done(STATE_DONE) or 783 * Next transfer is ready(STATE_RUNNING) 784 */ 785 static void *next_transfer(struct pl022 *pl022) 786 { 787 struct spi_message *msg = pl022->cur_msg; 788 struct spi_transfer *trans = pl022->cur_transfer; 789 790 /* Move to next transfer */ 791 if (trans->transfer_list.next != &msg->transfers) { 792 pl022->cur_transfer = 793 list_entry(trans->transfer_list.next, 794 struct spi_transfer, transfer_list); 795 return STATE_RUNNING; 796 } 797 return STATE_DONE; 798 } 799 800 /* 801 * This DMA functionality is only compiled in if we have 802 * access to the generic DMA devices/DMA engine. 803 */ 804 #ifdef CONFIG_DMA_ENGINE 805 static void unmap_free_dma_scatter(struct pl022 *pl022) 806 { 807 /* Unmap and free the SG tables */ 808 dma_unmap_sg(pl022->dma_tx_channel->device->dev, pl022->sgt_tx.sgl, 809 pl022->sgt_tx.nents, DMA_TO_DEVICE); 810 dma_unmap_sg(pl022->dma_rx_channel->device->dev, pl022->sgt_rx.sgl, 811 pl022->sgt_rx.nents, DMA_FROM_DEVICE); 812 sg_free_table(&pl022->sgt_rx); 813 sg_free_table(&pl022->sgt_tx); 814 } 815 816 static void dma_callback(void *data) 817 { 818 struct pl022 *pl022 = data; 819 struct spi_message *msg = pl022->cur_msg; 820 821 BUG_ON(!pl022->sgt_rx.sgl); 822 823 #ifdef VERBOSE_DEBUG 824 /* 825 * Optionally dump out buffers to inspect contents, this is 826 * good if you want to convince yourself that the loopback 827 * read/write contents are the same, when adopting to a new 828 * DMA engine. 829 */ 830 { 831 struct scatterlist *sg; 832 unsigned int i; 833 834 dma_sync_sg_for_cpu(&pl022->adev->dev, 835 pl022->sgt_rx.sgl, 836 pl022->sgt_rx.nents, 837 DMA_FROM_DEVICE); 838 839 for_each_sg(pl022->sgt_rx.sgl, sg, pl022->sgt_rx.nents, i) { 840 dev_dbg(&pl022->adev->dev, "SPI RX SG ENTRY: %d", i); 841 print_hex_dump(KERN_ERR, "SPI RX: ", 842 DUMP_PREFIX_OFFSET, 843 16, 844 1, 845 sg_virt(sg), 846 sg_dma_len(sg), 847 1); 848 } 849 for_each_sg(pl022->sgt_tx.sgl, sg, pl022->sgt_tx.nents, i) { 850 dev_dbg(&pl022->adev->dev, "SPI TX SG ENTRY: %d", i); 851 print_hex_dump(KERN_ERR, "SPI TX: ", 852 DUMP_PREFIX_OFFSET, 853 16, 854 1, 855 sg_virt(sg), 856 sg_dma_len(sg), 857 1); 858 } 859 } 860 #endif 861 862 unmap_free_dma_scatter(pl022); 863 864 /* Update total bytes transferred */ 865 msg->actual_length += pl022->cur_transfer->len; 866 if (pl022->cur_transfer->cs_change) 867 pl022_cs_control(pl022, SSP_CHIP_DESELECT); 868 869 /* Move to next transfer */ 870 msg->state = next_transfer(pl022); 871 tasklet_schedule(&pl022->pump_transfers); 872 } 873 874 static void setup_dma_scatter(struct pl022 *pl022, 875 void *buffer, 876 unsigned int length, 877 struct sg_table *sgtab) 878 { 879 struct scatterlist *sg; 880 int bytesleft = length; 881 void *bufp = buffer; 882 int mapbytes; 883 int i; 884 885 if (buffer) { 886 for_each_sg(sgtab->sgl, sg, sgtab->nents, i) { 887 /* 888 * If there are less bytes left than what fits 889 * in the current page (plus page alignment offset) 890 * we just feed in this, else we stuff in as much 891 * as we can. 892 */ 893 if (bytesleft < (PAGE_SIZE - offset_in_page(bufp))) 894 mapbytes = bytesleft; 895 else 896 mapbytes = PAGE_SIZE - offset_in_page(bufp); 897 sg_set_page(sg, virt_to_page(bufp), 898 mapbytes, offset_in_page(bufp)); 899 bufp += mapbytes; 900 bytesleft -= mapbytes; 901 dev_dbg(&pl022->adev->dev, 902 "set RX/TX target page @ %p, %d bytes, %d left\n", 903 bufp, mapbytes, bytesleft); 904 } 905 } else { 906 /* Map the dummy buffer on every page */ 907 for_each_sg(sgtab->sgl, sg, sgtab->nents, i) { 908 if (bytesleft < PAGE_SIZE) 909 mapbytes = bytesleft; 910 else 911 mapbytes = PAGE_SIZE; 912 sg_set_page(sg, virt_to_page(pl022->dummypage), 913 mapbytes, 0); 914 bytesleft -= mapbytes; 915 dev_dbg(&pl022->adev->dev, 916 "set RX/TX to dummy page %d bytes, %d left\n", 917 mapbytes, bytesleft); 918 919 } 920 } 921 BUG_ON(bytesleft); 922 } 923 924 /** 925 * configure_dma - configures the channels for the next transfer 926 * @pl022: SSP driver's private data structure 927 */ 928 static int configure_dma(struct pl022 *pl022) 929 { 930 struct dma_slave_config rx_conf = { 931 .src_addr = SSP_DR(pl022->phybase), 932 .direction = DMA_DEV_TO_MEM, 933 .device_fc = false, 934 }; 935 struct dma_slave_config tx_conf = { 936 .dst_addr = SSP_DR(pl022->phybase), 937 .direction = DMA_MEM_TO_DEV, 938 .device_fc = false, 939 }; 940 unsigned int pages; 941 int ret; 942 int rx_sglen, tx_sglen; 943 struct dma_chan *rxchan = pl022->dma_rx_channel; 944 struct dma_chan *txchan = pl022->dma_tx_channel; 945 struct dma_async_tx_descriptor *rxdesc; 946 struct dma_async_tx_descriptor *txdesc; 947 948 /* Check that the channels are available */ 949 if (!rxchan || !txchan) 950 return -ENODEV; 951 952 /* 953 * If supplied, the DMA burstsize should equal the FIFO trigger level. 954 * Notice that the DMA engine uses one-to-one mapping. Since we can 955 * not trigger on 2 elements this needs explicit mapping rather than 956 * calculation. 957 */ 958 switch (pl022->rx_lev_trig) { 959 case SSP_RX_1_OR_MORE_ELEM: 960 rx_conf.src_maxburst = 1; 961 break; 962 case SSP_RX_4_OR_MORE_ELEM: 963 rx_conf.src_maxburst = 4; 964 break; 965 case SSP_RX_8_OR_MORE_ELEM: 966 rx_conf.src_maxburst = 8; 967 break; 968 case SSP_RX_16_OR_MORE_ELEM: 969 rx_conf.src_maxburst = 16; 970 break; 971 case SSP_RX_32_OR_MORE_ELEM: 972 rx_conf.src_maxburst = 32; 973 break; 974 default: 975 rx_conf.src_maxburst = pl022->vendor->fifodepth >> 1; 976 break; 977 } 978 979 switch (pl022->tx_lev_trig) { 980 case SSP_TX_1_OR_MORE_EMPTY_LOC: 981 tx_conf.dst_maxburst = 1; 982 break; 983 case SSP_TX_4_OR_MORE_EMPTY_LOC: 984 tx_conf.dst_maxburst = 4; 985 break; 986 case SSP_TX_8_OR_MORE_EMPTY_LOC: 987 tx_conf.dst_maxburst = 8; 988 break; 989 case SSP_TX_16_OR_MORE_EMPTY_LOC: 990 tx_conf.dst_maxburst = 16; 991 break; 992 case SSP_TX_32_OR_MORE_EMPTY_LOC: 993 tx_conf.dst_maxburst = 32; 994 break; 995 default: 996 tx_conf.dst_maxburst = pl022->vendor->fifodepth >> 1; 997 break; 998 } 999 1000 switch (pl022->read) { 1001 case READING_NULL: 1002 /* Use the same as for writing */ 1003 rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_UNDEFINED; 1004 break; 1005 case READING_U8: 1006 rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 1007 break; 1008 case READING_U16: 1009 rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES; 1010 break; 1011 case READING_U32: 1012 rx_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; 1013 break; 1014 } 1015 1016 switch (pl022->write) { 1017 case WRITING_NULL: 1018 /* Use the same as for reading */ 1019 tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_UNDEFINED; 1020 break; 1021 case WRITING_U8: 1022 tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE; 1023 break; 1024 case WRITING_U16: 1025 tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES; 1026 break; 1027 case WRITING_U32: 1028 tx_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; 1029 break; 1030 } 1031 1032 /* SPI pecularity: we need to read and write the same width */ 1033 if (rx_conf.src_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED) 1034 rx_conf.src_addr_width = tx_conf.dst_addr_width; 1035 if (tx_conf.dst_addr_width == DMA_SLAVE_BUSWIDTH_UNDEFINED) 1036 tx_conf.dst_addr_width = rx_conf.src_addr_width; 1037 BUG_ON(rx_conf.src_addr_width != tx_conf.dst_addr_width); 1038 1039 dmaengine_slave_config(rxchan, &rx_conf); 1040 dmaengine_slave_config(txchan, &tx_conf); 1041 1042 /* Create sglists for the transfers */ 1043 pages = DIV_ROUND_UP(pl022->cur_transfer->len, PAGE_SIZE); 1044 dev_dbg(&pl022->adev->dev, "using %d pages for transfer\n", pages); 1045 1046 ret = sg_alloc_table(&pl022->sgt_rx, pages, GFP_ATOMIC); 1047 if (ret) 1048 goto err_alloc_rx_sg; 1049 1050 ret = sg_alloc_table(&pl022->sgt_tx, pages, GFP_ATOMIC); 1051 if (ret) 1052 goto err_alloc_tx_sg; 1053 1054 /* Fill in the scatterlists for the RX+TX buffers */ 1055 setup_dma_scatter(pl022, pl022->rx, 1056 pl022->cur_transfer->len, &pl022->sgt_rx); 1057 setup_dma_scatter(pl022, pl022->tx, 1058 pl022->cur_transfer->len, &pl022->sgt_tx); 1059 1060 /* Map DMA buffers */ 1061 rx_sglen = dma_map_sg(rxchan->device->dev, pl022->sgt_rx.sgl, 1062 pl022->sgt_rx.nents, DMA_FROM_DEVICE); 1063 if (!rx_sglen) 1064 goto err_rx_sgmap; 1065 1066 tx_sglen = dma_map_sg(txchan->device->dev, pl022->sgt_tx.sgl, 1067 pl022->sgt_tx.nents, DMA_TO_DEVICE); 1068 if (!tx_sglen) 1069 goto err_tx_sgmap; 1070 1071 /* Send both scatterlists */ 1072 rxdesc = dmaengine_prep_slave_sg(rxchan, 1073 pl022->sgt_rx.sgl, 1074 rx_sglen, 1075 DMA_DEV_TO_MEM, 1076 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 1077 if (!rxdesc) 1078 goto err_rxdesc; 1079 1080 txdesc = dmaengine_prep_slave_sg(txchan, 1081 pl022->sgt_tx.sgl, 1082 tx_sglen, 1083 DMA_MEM_TO_DEV, 1084 DMA_PREP_INTERRUPT | DMA_CTRL_ACK); 1085 if (!txdesc) 1086 goto err_txdesc; 1087 1088 /* Put the callback on the RX transfer only, that should finish last */ 1089 rxdesc->callback = dma_callback; 1090 rxdesc->callback_param = pl022; 1091 1092 /* Submit and fire RX and TX with TX last so we're ready to read! */ 1093 dmaengine_submit(rxdesc); 1094 dmaengine_submit(txdesc); 1095 dma_async_issue_pending(rxchan); 1096 dma_async_issue_pending(txchan); 1097 pl022->dma_running = true; 1098 1099 return 0; 1100 1101 err_txdesc: 1102 dmaengine_terminate_all(txchan); 1103 err_rxdesc: 1104 dmaengine_terminate_all(rxchan); 1105 dma_unmap_sg(txchan->device->dev, pl022->sgt_tx.sgl, 1106 pl022->sgt_tx.nents, DMA_TO_DEVICE); 1107 err_tx_sgmap: 1108 dma_unmap_sg(rxchan->device->dev, pl022->sgt_rx.sgl, 1109 pl022->sgt_rx.nents, DMA_FROM_DEVICE); 1110 err_rx_sgmap: 1111 sg_free_table(&pl022->sgt_tx); 1112 err_alloc_tx_sg: 1113 sg_free_table(&pl022->sgt_rx); 1114 err_alloc_rx_sg: 1115 return -ENOMEM; 1116 } 1117 1118 static int pl022_dma_probe(struct pl022 *pl022) 1119 { 1120 dma_cap_mask_t mask; 1121 1122 /* Try to acquire a generic DMA engine slave channel */ 1123 dma_cap_zero(mask); 1124 dma_cap_set(DMA_SLAVE, mask); 1125 /* 1126 * We need both RX and TX channels to do DMA, else do none 1127 * of them. 1128 */ 1129 pl022->dma_rx_channel = dma_request_channel(mask, 1130 pl022->master_info->dma_filter, 1131 pl022->master_info->dma_rx_param); 1132 if (!pl022->dma_rx_channel) { 1133 dev_dbg(&pl022->adev->dev, "no RX DMA channel!\n"); 1134 goto err_no_rxchan; 1135 } 1136 1137 pl022->dma_tx_channel = dma_request_channel(mask, 1138 pl022->master_info->dma_filter, 1139 pl022->master_info->dma_tx_param); 1140 if (!pl022->dma_tx_channel) { 1141 dev_dbg(&pl022->adev->dev, "no TX DMA channel!\n"); 1142 goto err_no_txchan; 1143 } 1144 1145 pl022->dummypage = kmalloc(PAGE_SIZE, GFP_KERNEL); 1146 if (!pl022->dummypage) 1147 goto err_no_dummypage; 1148 1149 dev_info(&pl022->adev->dev, "setup for DMA on RX %s, TX %s\n", 1150 dma_chan_name(pl022->dma_rx_channel), 1151 dma_chan_name(pl022->dma_tx_channel)); 1152 1153 return 0; 1154 1155 err_no_dummypage: 1156 dma_release_channel(pl022->dma_tx_channel); 1157 err_no_txchan: 1158 dma_release_channel(pl022->dma_rx_channel); 1159 pl022->dma_rx_channel = NULL; 1160 err_no_rxchan: 1161 dev_err(&pl022->adev->dev, 1162 "Failed to work in dma mode, work without dma!\n"); 1163 return -ENODEV; 1164 } 1165 1166 static int pl022_dma_autoprobe(struct pl022 *pl022) 1167 { 1168 struct device *dev = &pl022->adev->dev; 1169 1170 /* automatically configure DMA channels from platform, normally using DT */ 1171 pl022->dma_rx_channel = dma_request_slave_channel(dev, "rx"); 1172 if (!pl022->dma_rx_channel) 1173 goto err_no_rxchan; 1174 1175 pl022->dma_tx_channel = dma_request_slave_channel(dev, "tx"); 1176 if (!pl022->dma_tx_channel) 1177 goto err_no_txchan; 1178 1179 pl022->dummypage = kmalloc(PAGE_SIZE, GFP_KERNEL); 1180 if (!pl022->dummypage) 1181 goto err_no_dummypage; 1182 1183 return 0; 1184 1185 err_no_dummypage: 1186 dma_release_channel(pl022->dma_tx_channel); 1187 pl022->dma_tx_channel = NULL; 1188 err_no_txchan: 1189 dma_release_channel(pl022->dma_rx_channel); 1190 pl022->dma_rx_channel = NULL; 1191 err_no_rxchan: 1192 return -ENODEV; 1193 } 1194 1195 static void terminate_dma(struct pl022 *pl022) 1196 { 1197 struct dma_chan *rxchan = pl022->dma_rx_channel; 1198 struct dma_chan *txchan = pl022->dma_tx_channel; 1199 1200 dmaengine_terminate_all(rxchan); 1201 dmaengine_terminate_all(txchan); 1202 unmap_free_dma_scatter(pl022); 1203 pl022->dma_running = false; 1204 } 1205 1206 static void pl022_dma_remove(struct pl022 *pl022) 1207 { 1208 if (pl022->dma_running) 1209 terminate_dma(pl022); 1210 if (pl022->dma_tx_channel) 1211 dma_release_channel(pl022->dma_tx_channel); 1212 if (pl022->dma_rx_channel) 1213 dma_release_channel(pl022->dma_rx_channel); 1214 kfree(pl022->dummypage); 1215 } 1216 1217 #else 1218 static inline int configure_dma(struct pl022 *pl022) 1219 { 1220 return -ENODEV; 1221 } 1222 1223 static inline int pl022_dma_autoprobe(struct pl022 *pl022) 1224 { 1225 return 0; 1226 } 1227 1228 static inline int pl022_dma_probe(struct pl022 *pl022) 1229 { 1230 return 0; 1231 } 1232 1233 static inline void pl022_dma_remove(struct pl022 *pl022) 1234 { 1235 } 1236 #endif 1237 1238 /** 1239 * pl022_interrupt_handler - Interrupt handler for SSP controller 1240 * 1241 * This function handles interrupts generated for an interrupt based transfer. 1242 * If a receive overrun (ROR) interrupt is there then we disable SSP, flag the 1243 * current message's state as STATE_ERROR and schedule the tasklet 1244 * pump_transfers which will do the postprocessing of the current message by 1245 * calling giveback(). Otherwise it reads data from RX FIFO till there is no 1246 * more data, and writes data in TX FIFO till it is not full. If we complete 1247 * the transfer we move to the next transfer and schedule the tasklet. 1248 */ 1249 static irqreturn_t pl022_interrupt_handler(int irq, void *dev_id) 1250 { 1251 struct pl022 *pl022 = dev_id; 1252 struct spi_message *msg = pl022->cur_msg; 1253 u16 irq_status = 0; 1254 u16 flag = 0; 1255 1256 if (unlikely(!msg)) { 1257 dev_err(&pl022->adev->dev, 1258 "bad message state in interrupt handler"); 1259 /* Never fail */ 1260 return IRQ_HANDLED; 1261 } 1262 1263 /* Read the Interrupt Status Register */ 1264 irq_status = readw(SSP_MIS(pl022->virtbase)); 1265 1266 if (unlikely(!irq_status)) 1267 return IRQ_NONE; 1268 1269 /* 1270 * This handles the FIFO interrupts, the timeout 1271 * interrupts are flatly ignored, they cannot be 1272 * trusted. 1273 */ 1274 if (unlikely(irq_status & SSP_MIS_MASK_RORMIS)) { 1275 /* 1276 * Overrun interrupt - bail out since our Data has been 1277 * corrupted 1278 */ 1279 dev_err(&pl022->adev->dev, "FIFO overrun\n"); 1280 if (readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_RFF) 1281 dev_err(&pl022->adev->dev, 1282 "RXFIFO is full\n"); 1283 if (readw(SSP_SR(pl022->virtbase)) & SSP_SR_MASK_TNF) 1284 dev_err(&pl022->adev->dev, 1285 "TXFIFO is full\n"); 1286 1287 /* 1288 * Disable and clear interrupts, disable SSP, 1289 * mark message with bad status so it can be 1290 * retried. 1291 */ 1292 writew(DISABLE_ALL_INTERRUPTS, 1293 SSP_IMSC(pl022->virtbase)); 1294 writew(CLEAR_ALL_INTERRUPTS, SSP_ICR(pl022->virtbase)); 1295 writew((readw(SSP_CR1(pl022->virtbase)) & 1296 (~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase)); 1297 msg->state = STATE_ERROR; 1298 1299 /* Schedule message queue handler */ 1300 tasklet_schedule(&pl022->pump_transfers); 1301 return IRQ_HANDLED; 1302 } 1303 1304 readwriter(pl022); 1305 1306 if ((pl022->tx == pl022->tx_end) && (flag == 0)) { 1307 flag = 1; 1308 /* Disable Transmit interrupt, enable receive interrupt */ 1309 writew((readw(SSP_IMSC(pl022->virtbase)) & 1310 ~SSP_IMSC_MASK_TXIM) | SSP_IMSC_MASK_RXIM, 1311 SSP_IMSC(pl022->virtbase)); 1312 } 1313 1314 /* 1315 * Since all transactions must write as much as shall be read, 1316 * we can conclude the entire transaction once RX is complete. 1317 * At this point, all TX will always be finished. 1318 */ 1319 if (pl022->rx >= pl022->rx_end) { 1320 writew(DISABLE_ALL_INTERRUPTS, 1321 SSP_IMSC(pl022->virtbase)); 1322 writew(CLEAR_ALL_INTERRUPTS, SSP_ICR(pl022->virtbase)); 1323 if (unlikely(pl022->rx > pl022->rx_end)) { 1324 dev_warn(&pl022->adev->dev, "read %u surplus " 1325 "bytes (did you request an odd " 1326 "number of bytes on a 16bit bus?)\n", 1327 (u32) (pl022->rx - pl022->rx_end)); 1328 } 1329 /* Update total bytes transferred */ 1330 msg->actual_length += pl022->cur_transfer->len; 1331 if (pl022->cur_transfer->cs_change) 1332 pl022_cs_control(pl022, SSP_CHIP_DESELECT); 1333 /* Move to next transfer */ 1334 msg->state = next_transfer(pl022); 1335 tasklet_schedule(&pl022->pump_transfers); 1336 return IRQ_HANDLED; 1337 } 1338 1339 return IRQ_HANDLED; 1340 } 1341 1342 /** 1343 * This sets up the pointers to memory for the next message to 1344 * send out on the SPI bus. 1345 */ 1346 static int set_up_next_transfer(struct pl022 *pl022, 1347 struct spi_transfer *transfer) 1348 { 1349 int residue; 1350 1351 /* Sanity check the message for this bus width */ 1352 residue = pl022->cur_transfer->len % pl022->cur_chip->n_bytes; 1353 if (unlikely(residue != 0)) { 1354 dev_err(&pl022->adev->dev, 1355 "message of %u bytes to transmit but the current " 1356 "chip bus has a data width of %u bytes!\n", 1357 pl022->cur_transfer->len, 1358 pl022->cur_chip->n_bytes); 1359 dev_err(&pl022->adev->dev, "skipping this message\n"); 1360 return -EIO; 1361 } 1362 pl022->tx = (void *)transfer->tx_buf; 1363 pl022->tx_end = pl022->tx + pl022->cur_transfer->len; 1364 pl022->rx = (void *)transfer->rx_buf; 1365 pl022->rx_end = pl022->rx + pl022->cur_transfer->len; 1366 pl022->write = 1367 pl022->tx ? pl022->cur_chip->write : WRITING_NULL; 1368 pl022->read = pl022->rx ? pl022->cur_chip->read : READING_NULL; 1369 return 0; 1370 } 1371 1372 /** 1373 * pump_transfers - Tasklet function which schedules next transfer 1374 * when running in interrupt or DMA transfer mode. 1375 * @data: SSP driver private data structure 1376 * 1377 */ 1378 static void pump_transfers(unsigned long data) 1379 { 1380 struct pl022 *pl022 = (struct pl022 *) data; 1381 struct spi_message *message = NULL; 1382 struct spi_transfer *transfer = NULL; 1383 struct spi_transfer *previous = NULL; 1384 1385 /* Get current state information */ 1386 message = pl022->cur_msg; 1387 transfer = pl022->cur_transfer; 1388 1389 /* Handle for abort */ 1390 if (message->state == STATE_ERROR) { 1391 message->status = -EIO; 1392 giveback(pl022); 1393 return; 1394 } 1395 1396 /* Handle end of message */ 1397 if (message->state == STATE_DONE) { 1398 message->status = 0; 1399 giveback(pl022); 1400 return; 1401 } 1402 1403 /* Delay if requested at end of transfer before CS change */ 1404 if (message->state == STATE_RUNNING) { 1405 previous = list_entry(transfer->transfer_list.prev, 1406 struct spi_transfer, 1407 transfer_list); 1408 if (previous->delay_usecs) 1409 /* 1410 * FIXME: This runs in interrupt context. 1411 * Is this really smart? 1412 */ 1413 udelay(previous->delay_usecs); 1414 1415 /* Reselect chip select only if cs_change was requested */ 1416 if (previous->cs_change) 1417 pl022_cs_control(pl022, SSP_CHIP_SELECT); 1418 } else { 1419 /* STATE_START */ 1420 message->state = STATE_RUNNING; 1421 } 1422 1423 if (set_up_next_transfer(pl022, transfer)) { 1424 message->state = STATE_ERROR; 1425 message->status = -EIO; 1426 giveback(pl022); 1427 return; 1428 } 1429 /* Flush the FIFOs and let's go! */ 1430 flush(pl022); 1431 1432 if (pl022->cur_chip->enable_dma) { 1433 if (configure_dma(pl022)) { 1434 dev_dbg(&pl022->adev->dev, 1435 "configuration of DMA failed, fall back to interrupt mode\n"); 1436 goto err_config_dma; 1437 } 1438 return; 1439 } 1440 1441 err_config_dma: 1442 /* enable all interrupts except RX */ 1443 writew(ENABLE_ALL_INTERRUPTS & ~SSP_IMSC_MASK_RXIM, SSP_IMSC(pl022->virtbase)); 1444 } 1445 1446 static void do_interrupt_dma_transfer(struct pl022 *pl022) 1447 { 1448 /* 1449 * Default is to enable all interrupts except RX - 1450 * this will be enabled once TX is complete 1451 */ 1452 u32 irqflags = (u32)(ENABLE_ALL_INTERRUPTS & ~SSP_IMSC_MASK_RXIM); 1453 1454 /* Enable target chip, if not already active */ 1455 if (!pl022->next_msg_cs_active) 1456 pl022_cs_control(pl022, SSP_CHIP_SELECT); 1457 1458 if (set_up_next_transfer(pl022, pl022->cur_transfer)) { 1459 /* Error path */ 1460 pl022->cur_msg->state = STATE_ERROR; 1461 pl022->cur_msg->status = -EIO; 1462 giveback(pl022); 1463 return; 1464 } 1465 /* If we're using DMA, set up DMA here */ 1466 if (pl022->cur_chip->enable_dma) { 1467 /* Configure DMA transfer */ 1468 if (configure_dma(pl022)) { 1469 dev_dbg(&pl022->adev->dev, 1470 "configuration of DMA failed, fall back to interrupt mode\n"); 1471 goto err_config_dma; 1472 } 1473 /* Disable interrupts in DMA mode, IRQ from DMA controller */ 1474 irqflags = DISABLE_ALL_INTERRUPTS; 1475 } 1476 err_config_dma: 1477 /* Enable SSP, turn on interrupts */ 1478 writew((readw(SSP_CR1(pl022->virtbase)) | SSP_CR1_MASK_SSE), 1479 SSP_CR1(pl022->virtbase)); 1480 writew(irqflags, SSP_IMSC(pl022->virtbase)); 1481 } 1482 1483 static void do_polling_transfer(struct pl022 *pl022) 1484 { 1485 struct spi_message *message = NULL; 1486 struct spi_transfer *transfer = NULL; 1487 struct spi_transfer *previous = NULL; 1488 struct chip_data *chip; 1489 unsigned long time, timeout; 1490 1491 chip = pl022->cur_chip; 1492 message = pl022->cur_msg; 1493 1494 while (message->state != STATE_DONE) { 1495 /* Handle for abort */ 1496 if (message->state == STATE_ERROR) 1497 break; 1498 transfer = pl022->cur_transfer; 1499 1500 /* Delay if requested at end of transfer */ 1501 if (message->state == STATE_RUNNING) { 1502 previous = 1503 list_entry(transfer->transfer_list.prev, 1504 struct spi_transfer, transfer_list); 1505 if (previous->delay_usecs) 1506 udelay(previous->delay_usecs); 1507 if (previous->cs_change) 1508 pl022_cs_control(pl022, SSP_CHIP_SELECT); 1509 } else { 1510 /* STATE_START */ 1511 message->state = STATE_RUNNING; 1512 if (!pl022->next_msg_cs_active) 1513 pl022_cs_control(pl022, SSP_CHIP_SELECT); 1514 } 1515 1516 /* Configuration Changing Per Transfer */ 1517 if (set_up_next_transfer(pl022, transfer)) { 1518 /* Error path */ 1519 message->state = STATE_ERROR; 1520 break; 1521 } 1522 /* Flush FIFOs and enable SSP */ 1523 flush(pl022); 1524 writew((readw(SSP_CR1(pl022->virtbase)) | SSP_CR1_MASK_SSE), 1525 SSP_CR1(pl022->virtbase)); 1526 1527 dev_dbg(&pl022->adev->dev, "polling transfer ongoing ...\n"); 1528 1529 timeout = jiffies + msecs_to_jiffies(SPI_POLLING_TIMEOUT); 1530 while (pl022->tx < pl022->tx_end || pl022->rx < pl022->rx_end) { 1531 time = jiffies; 1532 readwriter(pl022); 1533 if (time_after(time, timeout)) { 1534 dev_warn(&pl022->adev->dev, 1535 "%s: timeout!\n", __func__); 1536 message->state = STATE_ERROR; 1537 goto out; 1538 } 1539 cpu_relax(); 1540 } 1541 1542 /* Update total byte transferred */ 1543 message->actual_length += pl022->cur_transfer->len; 1544 if (pl022->cur_transfer->cs_change) 1545 pl022_cs_control(pl022, SSP_CHIP_DESELECT); 1546 /* Move to next transfer */ 1547 message->state = next_transfer(pl022); 1548 } 1549 out: 1550 /* Handle end of message */ 1551 if (message->state == STATE_DONE) 1552 message->status = 0; 1553 else 1554 message->status = -EIO; 1555 1556 giveback(pl022); 1557 return; 1558 } 1559 1560 static int pl022_transfer_one_message(struct spi_master *master, 1561 struct spi_message *msg) 1562 { 1563 struct pl022 *pl022 = spi_master_get_devdata(master); 1564 1565 /* Initial message state */ 1566 pl022->cur_msg = msg; 1567 msg->state = STATE_START; 1568 1569 pl022->cur_transfer = list_entry(msg->transfers.next, 1570 struct spi_transfer, transfer_list); 1571 1572 /* Setup the SPI using the per chip configuration */ 1573 pl022->cur_chip = spi_get_ctldata(msg->spi); 1574 pl022->cur_cs = pl022->chipselects[msg->spi->chip_select]; 1575 1576 restore_state(pl022); 1577 flush(pl022); 1578 1579 if (pl022->cur_chip->xfer_type == POLLING_TRANSFER) 1580 do_polling_transfer(pl022); 1581 else 1582 do_interrupt_dma_transfer(pl022); 1583 1584 return 0; 1585 } 1586 1587 static int pl022_unprepare_transfer_hardware(struct spi_master *master) 1588 { 1589 struct pl022 *pl022 = spi_master_get_devdata(master); 1590 1591 /* nothing more to do - disable spi/ssp and power off */ 1592 writew((readw(SSP_CR1(pl022->virtbase)) & 1593 (~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase)); 1594 1595 return 0; 1596 } 1597 1598 static int verify_controller_parameters(struct pl022 *pl022, 1599 struct pl022_config_chip const *chip_info) 1600 { 1601 if ((chip_info->iface < SSP_INTERFACE_MOTOROLA_SPI) 1602 || (chip_info->iface > SSP_INTERFACE_UNIDIRECTIONAL)) { 1603 dev_err(&pl022->adev->dev, 1604 "interface is configured incorrectly\n"); 1605 return -EINVAL; 1606 } 1607 if ((chip_info->iface == SSP_INTERFACE_UNIDIRECTIONAL) && 1608 (!pl022->vendor->unidir)) { 1609 dev_err(&pl022->adev->dev, 1610 "unidirectional mode not supported in this " 1611 "hardware version\n"); 1612 return -EINVAL; 1613 } 1614 if ((chip_info->hierarchy != SSP_MASTER) 1615 && (chip_info->hierarchy != SSP_SLAVE)) { 1616 dev_err(&pl022->adev->dev, 1617 "hierarchy is configured incorrectly\n"); 1618 return -EINVAL; 1619 } 1620 if ((chip_info->com_mode != INTERRUPT_TRANSFER) 1621 && (chip_info->com_mode != DMA_TRANSFER) 1622 && (chip_info->com_mode != POLLING_TRANSFER)) { 1623 dev_err(&pl022->adev->dev, 1624 "Communication mode is configured incorrectly\n"); 1625 return -EINVAL; 1626 } 1627 switch (chip_info->rx_lev_trig) { 1628 case SSP_RX_1_OR_MORE_ELEM: 1629 case SSP_RX_4_OR_MORE_ELEM: 1630 case SSP_RX_8_OR_MORE_ELEM: 1631 /* These are always OK, all variants can handle this */ 1632 break; 1633 case SSP_RX_16_OR_MORE_ELEM: 1634 if (pl022->vendor->fifodepth < 16) { 1635 dev_err(&pl022->adev->dev, 1636 "RX FIFO Trigger Level is configured incorrectly\n"); 1637 return -EINVAL; 1638 } 1639 break; 1640 case SSP_RX_32_OR_MORE_ELEM: 1641 if (pl022->vendor->fifodepth < 32) { 1642 dev_err(&pl022->adev->dev, 1643 "RX FIFO Trigger Level is configured incorrectly\n"); 1644 return -EINVAL; 1645 } 1646 break; 1647 default: 1648 dev_err(&pl022->adev->dev, 1649 "RX FIFO Trigger Level is configured incorrectly\n"); 1650 return -EINVAL; 1651 } 1652 switch (chip_info->tx_lev_trig) { 1653 case SSP_TX_1_OR_MORE_EMPTY_LOC: 1654 case SSP_TX_4_OR_MORE_EMPTY_LOC: 1655 case SSP_TX_8_OR_MORE_EMPTY_LOC: 1656 /* These are always OK, all variants can handle this */ 1657 break; 1658 case SSP_TX_16_OR_MORE_EMPTY_LOC: 1659 if (pl022->vendor->fifodepth < 16) { 1660 dev_err(&pl022->adev->dev, 1661 "TX FIFO Trigger Level is configured incorrectly\n"); 1662 return -EINVAL; 1663 } 1664 break; 1665 case SSP_TX_32_OR_MORE_EMPTY_LOC: 1666 if (pl022->vendor->fifodepth < 32) { 1667 dev_err(&pl022->adev->dev, 1668 "TX FIFO Trigger Level is configured incorrectly\n"); 1669 return -EINVAL; 1670 } 1671 break; 1672 default: 1673 dev_err(&pl022->adev->dev, 1674 "TX FIFO Trigger Level is configured incorrectly\n"); 1675 return -EINVAL; 1676 } 1677 if (chip_info->iface == SSP_INTERFACE_NATIONAL_MICROWIRE) { 1678 if ((chip_info->ctrl_len < SSP_BITS_4) 1679 || (chip_info->ctrl_len > SSP_BITS_32)) { 1680 dev_err(&pl022->adev->dev, 1681 "CTRL LEN is configured incorrectly\n"); 1682 return -EINVAL; 1683 } 1684 if ((chip_info->wait_state != SSP_MWIRE_WAIT_ZERO) 1685 && (chip_info->wait_state != SSP_MWIRE_WAIT_ONE)) { 1686 dev_err(&pl022->adev->dev, 1687 "Wait State is configured incorrectly\n"); 1688 return -EINVAL; 1689 } 1690 /* Half duplex is only available in the ST Micro version */ 1691 if (pl022->vendor->extended_cr) { 1692 if ((chip_info->duplex != 1693 SSP_MICROWIRE_CHANNEL_FULL_DUPLEX) 1694 && (chip_info->duplex != 1695 SSP_MICROWIRE_CHANNEL_HALF_DUPLEX)) { 1696 dev_err(&pl022->adev->dev, 1697 "Microwire duplex mode is configured incorrectly\n"); 1698 return -EINVAL; 1699 } 1700 } else { 1701 if (chip_info->duplex != SSP_MICROWIRE_CHANNEL_FULL_DUPLEX) 1702 dev_err(&pl022->adev->dev, 1703 "Microwire half duplex mode requested," 1704 " but this is only available in the" 1705 " ST version of PL022\n"); 1706 return -EINVAL; 1707 } 1708 } 1709 return 0; 1710 } 1711 1712 static inline u32 spi_rate(u32 rate, u16 cpsdvsr, u16 scr) 1713 { 1714 return rate / (cpsdvsr * (1 + scr)); 1715 } 1716 1717 static int calculate_effective_freq(struct pl022 *pl022, int freq, struct 1718 ssp_clock_params * clk_freq) 1719 { 1720 /* Lets calculate the frequency parameters */ 1721 u16 cpsdvsr = CPSDVR_MIN, scr = SCR_MIN; 1722 u32 rate, max_tclk, min_tclk, best_freq = 0, best_cpsdvsr = 0, 1723 best_scr = 0, tmp, found = 0; 1724 1725 rate = clk_get_rate(pl022->clk); 1726 /* cpsdvscr = 2 & scr 0 */ 1727 max_tclk = spi_rate(rate, CPSDVR_MIN, SCR_MIN); 1728 /* cpsdvsr = 254 & scr = 255 */ 1729 min_tclk = spi_rate(rate, CPSDVR_MAX, SCR_MAX); 1730 1731 if (freq > max_tclk) 1732 dev_warn(&pl022->adev->dev, 1733 "Max speed that can be programmed is %d Hz, you requested %d\n", 1734 max_tclk, freq); 1735 1736 if (freq < min_tclk) { 1737 dev_err(&pl022->adev->dev, 1738 "Requested frequency: %d Hz is less than minimum possible %d Hz\n", 1739 freq, min_tclk); 1740 return -EINVAL; 1741 } 1742 1743 /* 1744 * best_freq will give closest possible available rate (<= requested 1745 * freq) for all values of scr & cpsdvsr. 1746 */ 1747 while ((cpsdvsr <= CPSDVR_MAX) && !found) { 1748 while (scr <= SCR_MAX) { 1749 tmp = spi_rate(rate, cpsdvsr, scr); 1750 1751 if (tmp > freq) { 1752 /* we need lower freq */ 1753 scr++; 1754 continue; 1755 } 1756 1757 /* 1758 * If found exact value, mark found and break. 1759 * If found more closer value, update and break. 1760 */ 1761 if (tmp > best_freq) { 1762 best_freq = tmp; 1763 best_cpsdvsr = cpsdvsr; 1764 best_scr = scr; 1765 1766 if (tmp == freq) 1767 found = 1; 1768 } 1769 /* 1770 * increased scr will give lower rates, which are not 1771 * required 1772 */ 1773 break; 1774 } 1775 cpsdvsr += 2; 1776 scr = SCR_MIN; 1777 } 1778 1779 WARN(!best_freq, "pl022: Matching cpsdvsr and scr not found for %d Hz rate \n", 1780 freq); 1781 1782 clk_freq->cpsdvsr = (u8) (best_cpsdvsr & 0xFF); 1783 clk_freq->scr = (u8) (best_scr & 0xFF); 1784 dev_dbg(&pl022->adev->dev, 1785 "SSP Target Frequency is: %u, Effective Frequency is %u\n", 1786 freq, best_freq); 1787 dev_dbg(&pl022->adev->dev, "SSP cpsdvsr = %d, scr = %d\n", 1788 clk_freq->cpsdvsr, clk_freq->scr); 1789 1790 return 0; 1791 } 1792 1793 /* 1794 * A piece of default chip info unless the platform 1795 * supplies it. 1796 */ 1797 static const struct pl022_config_chip pl022_default_chip_info = { 1798 .com_mode = POLLING_TRANSFER, 1799 .iface = SSP_INTERFACE_MOTOROLA_SPI, 1800 .hierarchy = SSP_SLAVE, 1801 .slave_tx_disable = DO_NOT_DRIVE_TX, 1802 .rx_lev_trig = SSP_RX_1_OR_MORE_ELEM, 1803 .tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC, 1804 .ctrl_len = SSP_BITS_8, 1805 .wait_state = SSP_MWIRE_WAIT_ZERO, 1806 .duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX, 1807 .cs_control = null_cs_control, 1808 }; 1809 1810 /** 1811 * pl022_setup - setup function registered to SPI master framework 1812 * @spi: spi device which is requesting setup 1813 * 1814 * This function is registered to the SPI framework for this SPI master 1815 * controller. If it is the first time when setup is called by this device, 1816 * this function will initialize the runtime state for this chip and save 1817 * the same in the device structure. Else it will update the runtime info 1818 * with the updated chip info. Nothing is really being written to the 1819 * controller hardware here, that is not done until the actual transfer 1820 * commence. 1821 */ 1822 static int pl022_setup(struct spi_device *spi) 1823 { 1824 struct pl022_config_chip const *chip_info; 1825 struct pl022_config_chip chip_info_dt; 1826 struct chip_data *chip; 1827 struct ssp_clock_params clk_freq = { .cpsdvsr = 0, .scr = 0}; 1828 int status = 0; 1829 struct pl022 *pl022 = spi_master_get_devdata(spi->master); 1830 unsigned int bits = spi->bits_per_word; 1831 u32 tmp; 1832 struct device_node *np = spi->dev.of_node; 1833 1834 if (!spi->max_speed_hz) 1835 return -EINVAL; 1836 1837 /* Get controller_state if one is supplied */ 1838 chip = spi_get_ctldata(spi); 1839 1840 if (chip == NULL) { 1841 chip = kzalloc(sizeof(struct chip_data), GFP_KERNEL); 1842 if (!chip) 1843 return -ENOMEM; 1844 dev_dbg(&spi->dev, 1845 "allocated memory for controller's runtime state\n"); 1846 } 1847 1848 /* Get controller data if one is supplied */ 1849 chip_info = spi->controller_data; 1850 1851 if (chip_info == NULL) { 1852 if (np) { 1853 chip_info_dt = pl022_default_chip_info; 1854 1855 chip_info_dt.hierarchy = SSP_MASTER; 1856 of_property_read_u32(np, "pl022,interface", 1857 &chip_info_dt.iface); 1858 of_property_read_u32(np, "pl022,com-mode", 1859 &chip_info_dt.com_mode); 1860 of_property_read_u32(np, "pl022,rx-level-trig", 1861 &chip_info_dt.rx_lev_trig); 1862 of_property_read_u32(np, "pl022,tx-level-trig", 1863 &chip_info_dt.tx_lev_trig); 1864 of_property_read_u32(np, "pl022,ctrl-len", 1865 &chip_info_dt.ctrl_len); 1866 of_property_read_u32(np, "pl022,wait-state", 1867 &chip_info_dt.wait_state); 1868 of_property_read_u32(np, "pl022,duplex", 1869 &chip_info_dt.duplex); 1870 1871 chip_info = &chip_info_dt; 1872 } else { 1873 chip_info = &pl022_default_chip_info; 1874 /* spi_board_info.controller_data not is supplied */ 1875 dev_dbg(&spi->dev, 1876 "using default controller_data settings\n"); 1877 } 1878 } else 1879 dev_dbg(&spi->dev, 1880 "using user supplied controller_data settings\n"); 1881 1882 /* 1883 * We can override with custom divisors, else we use the board 1884 * frequency setting 1885 */ 1886 if ((0 == chip_info->clk_freq.cpsdvsr) 1887 && (0 == chip_info->clk_freq.scr)) { 1888 status = calculate_effective_freq(pl022, 1889 spi->max_speed_hz, 1890 &clk_freq); 1891 if (status < 0) 1892 goto err_config_params; 1893 } else { 1894 memcpy(&clk_freq, &chip_info->clk_freq, sizeof(clk_freq)); 1895 if ((clk_freq.cpsdvsr % 2) != 0) 1896 clk_freq.cpsdvsr = 1897 clk_freq.cpsdvsr - 1; 1898 } 1899 if ((clk_freq.cpsdvsr < CPSDVR_MIN) 1900 || (clk_freq.cpsdvsr > CPSDVR_MAX)) { 1901 status = -EINVAL; 1902 dev_err(&spi->dev, 1903 "cpsdvsr is configured incorrectly\n"); 1904 goto err_config_params; 1905 } 1906 1907 status = verify_controller_parameters(pl022, chip_info); 1908 if (status) { 1909 dev_err(&spi->dev, "controller data is incorrect"); 1910 goto err_config_params; 1911 } 1912 1913 pl022->rx_lev_trig = chip_info->rx_lev_trig; 1914 pl022->tx_lev_trig = chip_info->tx_lev_trig; 1915 1916 /* Now set controller state based on controller data */ 1917 chip->xfer_type = chip_info->com_mode; 1918 if (!chip_info->cs_control) { 1919 chip->cs_control = null_cs_control; 1920 if (!gpio_is_valid(pl022->chipselects[spi->chip_select])) 1921 dev_warn(&spi->dev, 1922 "invalid chip select\n"); 1923 } else 1924 chip->cs_control = chip_info->cs_control; 1925 1926 /* Check bits per word with vendor specific range */ 1927 if ((bits <= 3) || (bits > pl022->vendor->max_bpw)) { 1928 status = -ENOTSUPP; 1929 dev_err(&spi->dev, "illegal data size for this controller!\n"); 1930 dev_err(&spi->dev, "This controller can only handle 4 <= n <= %d bit words\n", 1931 pl022->vendor->max_bpw); 1932 goto err_config_params; 1933 } else if (bits <= 8) { 1934 dev_dbg(&spi->dev, "4 <= n <=8 bits per word\n"); 1935 chip->n_bytes = 1; 1936 chip->read = READING_U8; 1937 chip->write = WRITING_U8; 1938 } else if (bits <= 16) { 1939 dev_dbg(&spi->dev, "9 <= n <= 16 bits per word\n"); 1940 chip->n_bytes = 2; 1941 chip->read = READING_U16; 1942 chip->write = WRITING_U16; 1943 } else { 1944 dev_dbg(&spi->dev, "17 <= n <= 32 bits per word\n"); 1945 chip->n_bytes = 4; 1946 chip->read = READING_U32; 1947 chip->write = WRITING_U32; 1948 } 1949 1950 /* Now Initialize all register settings required for this chip */ 1951 chip->cr0 = 0; 1952 chip->cr1 = 0; 1953 chip->dmacr = 0; 1954 chip->cpsr = 0; 1955 if ((chip_info->com_mode == DMA_TRANSFER) 1956 && ((pl022->master_info)->enable_dma)) { 1957 chip->enable_dma = true; 1958 dev_dbg(&spi->dev, "DMA mode set in controller state\n"); 1959 SSP_WRITE_BITS(chip->dmacr, SSP_DMA_ENABLED, 1960 SSP_DMACR_MASK_RXDMAE, 0); 1961 SSP_WRITE_BITS(chip->dmacr, SSP_DMA_ENABLED, 1962 SSP_DMACR_MASK_TXDMAE, 1); 1963 } else { 1964 chip->enable_dma = false; 1965 dev_dbg(&spi->dev, "DMA mode NOT set in controller state\n"); 1966 SSP_WRITE_BITS(chip->dmacr, SSP_DMA_DISABLED, 1967 SSP_DMACR_MASK_RXDMAE, 0); 1968 SSP_WRITE_BITS(chip->dmacr, SSP_DMA_DISABLED, 1969 SSP_DMACR_MASK_TXDMAE, 1); 1970 } 1971 1972 chip->cpsr = clk_freq.cpsdvsr; 1973 1974 /* Special setup for the ST micro extended control registers */ 1975 if (pl022->vendor->extended_cr) { 1976 u32 etx; 1977 1978 if (pl022->vendor->pl023) { 1979 /* These bits are only in the PL023 */ 1980 SSP_WRITE_BITS(chip->cr1, chip_info->clkdelay, 1981 SSP_CR1_MASK_FBCLKDEL_ST, 13); 1982 } else { 1983 /* These bits are in the PL022 but not PL023 */ 1984 SSP_WRITE_BITS(chip->cr0, chip_info->duplex, 1985 SSP_CR0_MASK_HALFDUP_ST, 5); 1986 SSP_WRITE_BITS(chip->cr0, chip_info->ctrl_len, 1987 SSP_CR0_MASK_CSS_ST, 16); 1988 SSP_WRITE_BITS(chip->cr0, chip_info->iface, 1989 SSP_CR0_MASK_FRF_ST, 21); 1990 SSP_WRITE_BITS(chip->cr1, chip_info->wait_state, 1991 SSP_CR1_MASK_MWAIT_ST, 6); 1992 } 1993 SSP_WRITE_BITS(chip->cr0, bits - 1, 1994 SSP_CR0_MASK_DSS_ST, 0); 1995 1996 if (spi->mode & SPI_LSB_FIRST) { 1997 tmp = SSP_RX_LSB; 1998 etx = SSP_TX_LSB; 1999 } else { 2000 tmp = SSP_RX_MSB; 2001 etx = SSP_TX_MSB; 2002 } 2003 SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_RENDN_ST, 4); 2004 SSP_WRITE_BITS(chip->cr1, etx, SSP_CR1_MASK_TENDN_ST, 5); 2005 SSP_WRITE_BITS(chip->cr1, chip_info->rx_lev_trig, 2006 SSP_CR1_MASK_RXIFLSEL_ST, 7); 2007 SSP_WRITE_BITS(chip->cr1, chip_info->tx_lev_trig, 2008 SSP_CR1_MASK_TXIFLSEL_ST, 10); 2009 } else { 2010 SSP_WRITE_BITS(chip->cr0, bits - 1, 2011 SSP_CR0_MASK_DSS, 0); 2012 SSP_WRITE_BITS(chip->cr0, chip_info->iface, 2013 SSP_CR0_MASK_FRF, 4); 2014 } 2015 2016 /* Stuff that is common for all versions */ 2017 if (spi->mode & SPI_CPOL) 2018 tmp = SSP_CLK_POL_IDLE_HIGH; 2019 else 2020 tmp = SSP_CLK_POL_IDLE_LOW; 2021 SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPO, 6); 2022 2023 if (spi->mode & SPI_CPHA) 2024 tmp = SSP_CLK_SECOND_EDGE; 2025 else 2026 tmp = SSP_CLK_FIRST_EDGE; 2027 SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPH, 7); 2028 2029 SSP_WRITE_BITS(chip->cr0, clk_freq.scr, SSP_CR0_MASK_SCR, 8); 2030 /* Loopback is available on all versions except PL023 */ 2031 if (pl022->vendor->loopback) { 2032 if (spi->mode & SPI_LOOP) 2033 tmp = LOOPBACK_ENABLED; 2034 else 2035 tmp = LOOPBACK_DISABLED; 2036 SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_LBM, 0); 2037 } 2038 SSP_WRITE_BITS(chip->cr1, SSP_DISABLED, SSP_CR1_MASK_SSE, 1); 2039 SSP_WRITE_BITS(chip->cr1, chip_info->hierarchy, SSP_CR1_MASK_MS, 2); 2040 SSP_WRITE_BITS(chip->cr1, chip_info->slave_tx_disable, SSP_CR1_MASK_SOD, 2041 3); 2042 2043 /* Save controller_state */ 2044 spi_set_ctldata(spi, chip); 2045 return status; 2046 err_config_params: 2047 spi_set_ctldata(spi, NULL); 2048 kfree(chip); 2049 return status; 2050 } 2051 2052 /** 2053 * pl022_cleanup - cleanup function registered to SPI master framework 2054 * @spi: spi device which is requesting cleanup 2055 * 2056 * This function is registered to the SPI framework for this SPI master 2057 * controller. It will free the runtime state of chip. 2058 */ 2059 static void pl022_cleanup(struct spi_device *spi) 2060 { 2061 struct chip_data *chip = spi_get_ctldata(spi); 2062 2063 spi_set_ctldata(spi, NULL); 2064 kfree(chip); 2065 } 2066 2067 static struct pl022_ssp_controller * 2068 pl022_platform_data_dt_get(struct device *dev) 2069 { 2070 struct device_node *np = dev->of_node; 2071 struct pl022_ssp_controller *pd; 2072 u32 tmp; 2073 2074 if (!np) { 2075 dev_err(dev, "no dt node defined\n"); 2076 return NULL; 2077 } 2078 2079 pd = devm_kzalloc(dev, sizeof(struct pl022_ssp_controller), GFP_KERNEL); 2080 if (!pd) 2081 return NULL; 2082 2083 pd->bus_id = -1; 2084 pd->enable_dma = 1; 2085 of_property_read_u32(np, "num-cs", &tmp); 2086 pd->num_chipselect = tmp; 2087 of_property_read_u32(np, "pl022,autosuspend-delay", 2088 &pd->autosuspend_delay); 2089 pd->rt = of_property_read_bool(np, "pl022,rt"); 2090 2091 return pd; 2092 } 2093 2094 static int pl022_probe(struct amba_device *adev, const struct amba_id *id) 2095 { 2096 struct device *dev = &adev->dev; 2097 struct pl022_ssp_controller *platform_info = 2098 dev_get_platdata(&adev->dev); 2099 struct spi_master *master; 2100 struct pl022 *pl022 = NULL; /*Data for this driver */ 2101 struct device_node *np = adev->dev.of_node; 2102 int status = 0, i, num_cs; 2103 2104 dev_info(&adev->dev, 2105 "ARM PL022 driver, device ID: 0x%08x\n", adev->periphid); 2106 if (!platform_info && IS_ENABLED(CONFIG_OF)) 2107 platform_info = pl022_platform_data_dt_get(dev); 2108 2109 if (!platform_info) { 2110 dev_err(dev, "probe: no platform data defined\n"); 2111 return -ENODEV; 2112 } 2113 2114 if (platform_info->num_chipselect) { 2115 num_cs = platform_info->num_chipselect; 2116 } else { 2117 dev_err(dev, "probe: no chip select defined\n"); 2118 return -ENODEV; 2119 } 2120 2121 /* Allocate master with space for data */ 2122 master = spi_alloc_master(dev, sizeof(struct pl022)); 2123 if (master == NULL) { 2124 dev_err(&adev->dev, "probe - cannot alloc SPI master\n"); 2125 return -ENOMEM; 2126 } 2127 2128 pl022 = spi_master_get_devdata(master); 2129 pl022->master = master; 2130 pl022->master_info = platform_info; 2131 pl022->adev = adev; 2132 pl022->vendor = id->data; 2133 pl022->chipselects = devm_kzalloc(dev, num_cs * sizeof(int), 2134 GFP_KERNEL); 2135 if (!pl022->chipselects) { 2136 status = -ENOMEM; 2137 goto err_no_mem; 2138 } 2139 2140 /* 2141 * Bus Number Which has been Assigned to this SSP controller 2142 * on this board 2143 */ 2144 master->bus_num = platform_info->bus_id; 2145 master->num_chipselect = num_cs; 2146 master->cleanup = pl022_cleanup; 2147 master->setup = pl022_setup; 2148 master->auto_runtime_pm = true; 2149 master->transfer_one_message = pl022_transfer_one_message; 2150 master->unprepare_transfer_hardware = pl022_unprepare_transfer_hardware; 2151 master->rt = platform_info->rt; 2152 master->dev.of_node = dev->of_node; 2153 2154 if (platform_info->num_chipselect && platform_info->chipselects) { 2155 for (i = 0; i < num_cs; i++) 2156 pl022->chipselects[i] = platform_info->chipselects[i]; 2157 } else if (pl022->vendor->internal_cs_ctrl) { 2158 for (i = 0; i < num_cs; i++) 2159 pl022->chipselects[i] = i; 2160 } else if (IS_ENABLED(CONFIG_OF)) { 2161 for (i = 0; i < num_cs; i++) { 2162 int cs_gpio = of_get_named_gpio(np, "cs-gpios", i); 2163 2164 if (cs_gpio == -EPROBE_DEFER) { 2165 status = -EPROBE_DEFER; 2166 goto err_no_gpio; 2167 } 2168 2169 pl022->chipselects[i] = cs_gpio; 2170 2171 if (gpio_is_valid(cs_gpio)) { 2172 if (devm_gpio_request(dev, cs_gpio, "ssp-pl022")) 2173 dev_err(&adev->dev, 2174 "could not request %d gpio\n", 2175 cs_gpio); 2176 else if (gpio_direction_output(cs_gpio, 1)) 2177 dev_err(&adev->dev, 2178 "could not set gpio %d as output\n", 2179 cs_gpio); 2180 } 2181 } 2182 } 2183 2184 /* 2185 * Supports mode 0-3, loopback, and active low CS. Transfers are 2186 * always MS bit first on the original pl022. 2187 */ 2188 master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP; 2189 if (pl022->vendor->extended_cr) 2190 master->mode_bits |= SPI_LSB_FIRST; 2191 2192 dev_dbg(&adev->dev, "BUSNO: %d\n", master->bus_num); 2193 2194 status = amba_request_regions(adev, NULL); 2195 if (status) 2196 goto err_no_ioregion; 2197 2198 pl022->phybase = adev->res.start; 2199 pl022->virtbase = devm_ioremap(dev, adev->res.start, 2200 resource_size(&adev->res)); 2201 if (pl022->virtbase == NULL) { 2202 status = -ENOMEM; 2203 goto err_no_ioremap; 2204 } 2205 dev_info(&adev->dev, "mapped registers from %pa to %p\n", 2206 &adev->res.start, pl022->virtbase); 2207 2208 pl022->clk = devm_clk_get(&adev->dev, NULL); 2209 if (IS_ERR(pl022->clk)) { 2210 status = PTR_ERR(pl022->clk); 2211 dev_err(&adev->dev, "could not retrieve SSP/SPI bus clock\n"); 2212 goto err_no_clk; 2213 } 2214 2215 status = clk_prepare_enable(pl022->clk); 2216 if (status) { 2217 dev_err(&adev->dev, "could not enable SSP/SPI bus clock\n"); 2218 goto err_no_clk_en; 2219 } 2220 2221 /* Initialize transfer pump */ 2222 tasklet_init(&pl022->pump_transfers, pump_transfers, 2223 (unsigned long)pl022); 2224 2225 /* Disable SSP */ 2226 writew((readw(SSP_CR1(pl022->virtbase)) & (~SSP_CR1_MASK_SSE)), 2227 SSP_CR1(pl022->virtbase)); 2228 load_ssp_default_config(pl022); 2229 2230 status = devm_request_irq(dev, adev->irq[0], pl022_interrupt_handler, 2231 0, "pl022", pl022); 2232 if (status < 0) { 2233 dev_err(&adev->dev, "probe - cannot get IRQ (%d)\n", status); 2234 goto err_no_irq; 2235 } 2236 2237 /* Get DMA channels, try autoconfiguration first */ 2238 status = pl022_dma_autoprobe(pl022); 2239 2240 /* If that failed, use channels from platform_info */ 2241 if (status == 0) 2242 platform_info->enable_dma = 1; 2243 else if (platform_info->enable_dma) { 2244 status = pl022_dma_probe(pl022); 2245 if (status != 0) 2246 platform_info->enable_dma = 0; 2247 } 2248 2249 /* Register with the SPI framework */ 2250 amba_set_drvdata(adev, pl022); 2251 status = devm_spi_register_master(&adev->dev, master); 2252 if (status != 0) { 2253 dev_err(&adev->dev, 2254 "probe - problem registering spi master\n"); 2255 goto err_spi_register; 2256 } 2257 dev_dbg(dev, "probe succeeded\n"); 2258 2259 /* let runtime pm put suspend */ 2260 if (platform_info->autosuspend_delay > 0) { 2261 dev_info(&adev->dev, 2262 "will use autosuspend for runtime pm, delay %dms\n", 2263 platform_info->autosuspend_delay); 2264 pm_runtime_set_autosuspend_delay(dev, 2265 platform_info->autosuspend_delay); 2266 pm_runtime_use_autosuspend(dev); 2267 } 2268 pm_runtime_put(dev); 2269 2270 return 0; 2271 2272 err_spi_register: 2273 if (platform_info->enable_dma) 2274 pl022_dma_remove(pl022); 2275 err_no_irq: 2276 clk_disable_unprepare(pl022->clk); 2277 err_no_clk_en: 2278 err_no_clk: 2279 err_no_ioremap: 2280 amba_release_regions(adev); 2281 err_no_ioregion: 2282 err_no_gpio: 2283 err_no_mem: 2284 spi_master_put(master); 2285 return status; 2286 } 2287 2288 static int 2289 pl022_remove(struct amba_device *adev) 2290 { 2291 struct pl022 *pl022 = amba_get_drvdata(adev); 2292 2293 if (!pl022) 2294 return 0; 2295 2296 /* 2297 * undo pm_runtime_put() in probe. I assume that we're not 2298 * accessing the primecell here. 2299 */ 2300 pm_runtime_get_noresume(&adev->dev); 2301 2302 load_ssp_default_config(pl022); 2303 if (pl022->master_info->enable_dma) 2304 pl022_dma_remove(pl022); 2305 2306 clk_disable_unprepare(pl022->clk); 2307 amba_release_regions(adev); 2308 tasklet_disable(&pl022->pump_transfers); 2309 return 0; 2310 } 2311 2312 #ifdef CONFIG_PM_SLEEP 2313 static int pl022_suspend(struct device *dev) 2314 { 2315 struct pl022 *pl022 = dev_get_drvdata(dev); 2316 int ret; 2317 2318 ret = spi_master_suspend(pl022->master); 2319 if (ret) { 2320 dev_warn(dev, "cannot suspend master\n"); 2321 return ret; 2322 } 2323 2324 ret = pm_runtime_force_suspend(dev); 2325 if (ret) { 2326 spi_master_resume(pl022->master); 2327 return ret; 2328 } 2329 2330 pinctrl_pm_select_sleep_state(dev); 2331 2332 dev_dbg(dev, "suspended\n"); 2333 return 0; 2334 } 2335 2336 static int pl022_resume(struct device *dev) 2337 { 2338 struct pl022 *pl022 = dev_get_drvdata(dev); 2339 int ret; 2340 2341 ret = pm_runtime_force_resume(dev); 2342 if (ret) 2343 dev_err(dev, "problem resuming\n"); 2344 2345 /* Start the queue running */ 2346 ret = spi_master_resume(pl022->master); 2347 if (ret) 2348 dev_err(dev, "problem starting queue (%d)\n", ret); 2349 else 2350 dev_dbg(dev, "resumed\n"); 2351 2352 return ret; 2353 } 2354 #endif 2355 2356 #ifdef CONFIG_PM 2357 static int pl022_runtime_suspend(struct device *dev) 2358 { 2359 struct pl022 *pl022 = dev_get_drvdata(dev); 2360 2361 clk_disable_unprepare(pl022->clk); 2362 pinctrl_pm_select_idle_state(dev); 2363 2364 return 0; 2365 } 2366 2367 static int pl022_runtime_resume(struct device *dev) 2368 { 2369 struct pl022 *pl022 = dev_get_drvdata(dev); 2370 2371 pinctrl_pm_select_default_state(dev); 2372 clk_prepare_enable(pl022->clk); 2373 2374 return 0; 2375 } 2376 #endif 2377 2378 static const struct dev_pm_ops pl022_dev_pm_ops = { 2379 SET_SYSTEM_SLEEP_PM_OPS(pl022_suspend, pl022_resume) 2380 SET_RUNTIME_PM_OPS(pl022_runtime_suspend, pl022_runtime_resume, NULL) 2381 }; 2382 2383 static struct vendor_data vendor_arm = { 2384 .fifodepth = 8, 2385 .max_bpw = 16, 2386 .unidir = false, 2387 .extended_cr = false, 2388 .pl023 = false, 2389 .loopback = true, 2390 .internal_cs_ctrl = false, 2391 }; 2392 2393 static struct vendor_data vendor_st = { 2394 .fifodepth = 32, 2395 .max_bpw = 32, 2396 .unidir = false, 2397 .extended_cr = true, 2398 .pl023 = false, 2399 .loopback = true, 2400 .internal_cs_ctrl = false, 2401 }; 2402 2403 static struct vendor_data vendor_st_pl023 = { 2404 .fifodepth = 32, 2405 .max_bpw = 32, 2406 .unidir = false, 2407 .extended_cr = true, 2408 .pl023 = true, 2409 .loopback = false, 2410 .internal_cs_ctrl = false, 2411 }; 2412 2413 static struct vendor_data vendor_lsi = { 2414 .fifodepth = 8, 2415 .max_bpw = 16, 2416 .unidir = false, 2417 .extended_cr = false, 2418 .pl023 = false, 2419 .loopback = true, 2420 .internal_cs_ctrl = true, 2421 }; 2422 2423 static struct amba_id pl022_ids[] = { 2424 { 2425 /* 2426 * ARM PL022 variant, this has a 16bit wide 2427 * and 8 locations deep TX/RX FIFO 2428 */ 2429 .id = 0x00041022, 2430 .mask = 0x000fffff, 2431 .data = &vendor_arm, 2432 }, 2433 { 2434 /* 2435 * ST Micro derivative, this has 32bit wide 2436 * and 32 locations deep TX/RX FIFO 2437 */ 2438 .id = 0x01080022, 2439 .mask = 0xffffffff, 2440 .data = &vendor_st, 2441 }, 2442 { 2443 /* 2444 * ST-Ericsson derivative "PL023" (this is not 2445 * an official ARM number), this is a PL022 SSP block 2446 * stripped to SPI mode only, it has 32bit wide 2447 * and 32 locations deep TX/RX FIFO but no extended 2448 * CR0/CR1 register 2449 */ 2450 .id = 0x00080023, 2451 .mask = 0xffffffff, 2452 .data = &vendor_st_pl023, 2453 }, 2454 { 2455 /* 2456 * PL022 variant that has a chip select control register whih 2457 * allows control of 5 output signals nCS[0:4]. 2458 */ 2459 .id = 0x000b6022, 2460 .mask = 0x000fffff, 2461 .data = &vendor_lsi, 2462 }, 2463 { 0, 0 }, 2464 }; 2465 2466 MODULE_DEVICE_TABLE(amba, pl022_ids); 2467 2468 static struct amba_driver pl022_driver = { 2469 .drv = { 2470 .name = "ssp-pl022", 2471 .pm = &pl022_dev_pm_ops, 2472 }, 2473 .id_table = pl022_ids, 2474 .probe = pl022_probe, 2475 .remove = pl022_remove, 2476 }; 2477 2478 static int __init pl022_init(void) 2479 { 2480 return amba_driver_register(&pl022_driver); 2481 } 2482 subsys_initcall(pl022_init); 2483 2484 static void __exit pl022_exit(void) 2485 { 2486 amba_driver_unregister(&pl022_driver); 2487 } 2488 module_exit(pl022_exit); 2489 2490 MODULE_AUTHOR("Linus Walleij <linus.walleij@stericsson.com>"); 2491 MODULE_DESCRIPTION("PL022 SSP Controller Driver"); 2492 MODULE_LICENSE("GPL"); 2493