xref: /openbmc/linux/drivers/spi/spi-pic32.c (revision aeefc1a0)
1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3  * Microchip PIC32 SPI controller driver.
4  *
5  * Purna Chandra Mandal <purna.mandal@microchip.com>
6  * Copyright (c) 2016, Microchip Technology Inc.
7  */
8 
9 #include <linux/clk.h>
10 #include <linux/clkdev.h>
11 #include <linux/delay.h>
12 #include <linux/dmaengine.h>
13 #include <linux/dma-mapping.h>
14 #include <linux/highmem.h>
15 #include <linux/module.h>
16 #include <linux/io.h>
17 #include <linux/interrupt.h>
18 #include <linux/of.h>
19 #include <linux/of_irq.h>
20 #include <linux/of_gpio.h>
21 #include <linux/of_address.h>
22 #include <linux/platform_device.h>
23 #include <linux/spi/spi.h>
24 
25 /* SPI controller registers */
26 struct pic32_spi_regs {
27 	u32 ctrl;
28 	u32 ctrl_clr;
29 	u32 ctrl_set;
30 	u32 ctrl_inv;
31 	u32 status;
32 	u32 status_clr;
33 	u32 status_set;
34 	u32 status_inv;
35 	u32 buf;
36 	u32 dontuse[3];
37 	u32 baud;
38 	u32 dontuse2[3];
39 	u32 ctrl2;
40 	u32 ctrl2_clr;
41 	u32 ctrl2_set;
42 	u32 ctrl2_inv;
43 };
44 
45 /* Bit fields of SPI Control Register */
46 #define CTRL_RX_INT_SHIFT	0  /* Rx interrupt generation */
47 #define  RX_FIFO_EMPTY		0
48 #define  RX_FIFO_NOT_EMPTY	1 /* not empty */
49 #define  RX_FIFO_HALF_FULL	2 /* full by half or more */
50 #define  RX_FIFO_FULL		3 /* completely full */
51 
52 #define CTRL_TX_INT_SHIFT	2  /* TX interrupt generation */
53 #define  TX_FIFO_ALL_EMPTY	0 /* completely empty */
54 #define  TX_FIFO_EMPTY		1 /* empty */
55 #define  TX_FIFO_HALF_EMPTY	2 /* empty by half or more */
56 #define  TX_FIFO_NOT_FULL	3 /* atleast one empty */
57 
58 #define CTRL_MSTEN	BIT(5) /* enable master mode */
59 #define CTRL_CKP	BIT(6) /* active low */
60 #define CTRL_CKE	BIT(8) /* Tx on falling edge */
61 #define CTRL_SMP	BIT(9) /* Rx at middle or end of tx */
62 #define CTRL_BPW_MASK	0x03   /* bits per word/sample */
63 #define CTRL_BPW_SHIFT	10
64 #define  PIC32_BPW_8	0
65 #define  PIC32_BPW_16	1
66 #define  PIC32_BPW_32	2
67 #define CTRL_SIDL	BIT(13) /* sleep when idle */
68 #define CTRL_ON		BIT(15) /* enable macro */
69 #define CTRL_ENHBUF	BIT(16) /* enable enhanced buffering */
70 #define CTRL_MCLKSEL	BIT(23) /* select clock source */
71 #define CTRL_MSSEN	BIT(28) /* macro driven /SS */
72 #define CTRL_FRMEN	BIT(31) /* enable framing mode */
73 
74 /* Bit fields of SPI Status Register */
75 #define STAT_RF_EMPTY	BIT(5) /* RX Fifo empty */
76 #define STAT_RX_OV	BIT(6) /* err, s/w needs to clear */
77 #define STAT_TX_UR	BIT(8) /* UR in Framed SPI modes */
78 #define STAT_FRM_ERR	BIT(12) /* Multiple Frame Sync pulse */
79 #define STAT_TF_LVL_MASK	0x1F
80 #define STAT_TF_LVL_SHIFT	16
81 #define STAT_RF_LVL_MASK	0x1F
82 #define STAT_RF_LVL_SHIFT	24
83 
84 /* Bit fields of SPI Baud Register */
85 #define BAUD_MASK		0x1ff
86 
87 /* Bit fields of SPI Control2 Register */
88 #define CTRL2_TX_UR_EN		BIT(10) /* Enable int on Tx under-run */
89 #define CTRL2_RX_OV_EN		BIT(11) /* Enable int on Rx over-run */
90 #define CTRL2_FRM_ERR_EN	BIT(12) /* Enable frame err int */
91 
92 /* Minimum DMA transfer size */
93 #define PIC32_DMA_LEN_MIN	64
94 
95 struct pic32_spi {
96 	dma_addr_t		dma_base;
97 	struct pic32_spi_regs __iomem *regs;
98 	int			fault_irq;
99 	int			rx_irq;
100 	int			tx_irq;
101 	u32			fifo_n_byte; /* FIFO depth in bytes */
102 	struct clk		*clk;
103 	struct spi_master	*master;
104 	/* Current controller setting */
105 	u32			speed_hz; /* spi-clk rate */
106 	u32			mode;
107 	u32			bits_per_word;
108 	u32			fifo_n_elm; /* FIFO depth in words */
109 #define PIC32F_DMA_PREP		0 /* DMA chnls configured */
110 	unsigned long		flags;
111 	/* Current transfer state */
112 	struct completion	xfer_done;
113 	/* PIO transfer specific */
114 	const void		*tx;
115 	const void		*tx_end;
116 	const void		*rx;
117 	const void		*rx_end;
118 	int			len;
119 	void (*rx_fifo)(struct pic32_spi *);
120 	void (*tx_fifo)(struct pic32_spi *);
121 };
122 
123 static inline void pic32_spi_enable(struct pic32_spi *pic32s)
124 {
125 	writel(CTRL_ON | CTRL_SIDL, &pic32s->regs->ctrl_set);
126 }
127 
128 static inline void pic32_spi_disable(struct pic32_spi *pic32s)
129 {
130 	writel(CTRL_ON | CTRL_SIDL, &pic32s->regs->ctrl_clr);
131 
132 	/* avoid SPI registers read/write at immediate next CPU clock */
133 	ndelay(20);
134 }
135 
136 static void pic32_spi_set_clk_rate(struct pic32_spi *pic32s, u32 spi_ck)
137 {
138 	u32 div;
139 
140 	/* div = (clk_in / 2 * spi_ck) - 1 */
141 	div = DIV_ROUND_CLOSEST(clk_get_rate(pic32s->clk), 2 * spi_ck) - 1;
142 
143 	writel(div & BAUD_MASK, &pic32s->regs->baud);
144 }
145 
146 static inline u32 pic32_rx_fifo_level(struct pic32_spi *pic32s)
147 {
148 	u32 sr = readl(&pic32s->regs->status);
149 
150 	return (sr >> STAT_RF_LVL_SHIFT) & STAT_RF_LVL_MASK;
151 }
152 
153 static inline u32 pic32_tx_fifo_level(struct pic32_spi *pic32s)
154 {
155 	u32 sr = readl(&pic32s->regs->status);
156 
157 	return (sr >> STAT_TF_LVL_SHIFT) & STAT_TF_LVL_MASK;
158 }
159 
160 /* Return the max entries we can fill into tx fifo */
161 static u32 pic32_tx_max(struct pic32_spi *pic32s, int n_bytes)
162 {
163 	u32 tx_left, tx_room, rxtx_gap;
164 
165 	tx_left = (pic32s->tx_end - pic32s->tx) / n_bytes;
166 	tx_room = pic32s->fifo_n_elm - pic32_tx_fifo_level(pic32s);
167 
168 	/*
169 	 * Another concern is about the tx/rx mismatch, we
170 	 * though to use (pic32s->fifo_n_byte - rxfl - txfl) as
171 	 * one maximum value for tx, but it doesn't cover the
172 	 * data which is out of tx/rx fifo and inside the
173 	 * shift registers. So a ctrl from sw point of
174 	 * view is taken.
175 	 */
176 	rxtx_gap = ((pic32s->rx_end - pic32s->rx) -
177 		    (pic32s->tx_end - pic32s->tx)) / n_bytes;
178 	return min3(tx_left, tx_room, (u32)(pic32s->fifo_n_elm - rxtx_gap));
179 }
180 
181 /* Return the max entries we should read out of rx fifo */
182 static u32 pic32_rx_max(struct pic32_spi *pic32s, int n_bytes)
183 {
184 	u32 rx_left = (pic32s->rx_end - pic32s->rx) / n_bytes;
185 
186 	return min_t(u32, rx_left, pic32_rx_fifo_level(pic32s));
187 }
188 
189 #define BUILD_SPI_FIFO_RW(__name, __type, __bwl)		\
190 static void pic32_spi_rx_##__name(struct pic32_spi *pic32s)	\
191 {								\
192 	__type v;						\
193 	u32 mx = pic32_rx_max(pic32s, sizeof(__type));		\
194 	for (; mx; mx--) {					\
195 		v = read##__bwl(&pic32s->regs->buf);		\
196 		if (pic32s->rx_end - pic32s->len)		\
197 			*(__type *)(pic32s->rx) = v;		\
198 		pic32s->rx += sizeof(__type);			\
199 	}							\
200 }								\
201 								\
202 static void pic32_spi_tx_##__name(struct pic32_spi *pic32s)	\
203 {								\
204 	__type v;						\
205 	u32 mx = pic32_tx_max(pic32s, sizeof(__type));		\
206 	for (; mx ; mx--) {					\
207 		v = (__type)~0U;				\
208 		if (pic32s->tx_end - pic32s->len)		\
209 			v = *(__type *)(pic32s->tx);		\
210 		write##__bwl(v, &pic32s->regs->buf);		\
211 		pic32s->tx += sizeof(__type);			\
212 	}							\
213 }
214 
215 BUILD_SPI_FIFO_RW(byte, u8, b);
216 BUILD_SPI_FIFO_RW(word, u16, w);
217 BUILD_SPI_FIFO_RW(dword, u32, l);
218 
219 static void pic32_err_stop(struct pic32_spi *pic32s, const char *msg)
220 {
221 	/* disable all interrupts */
222 	disable_irq_nosync(pic32s->fault_irq);
223 	disable_irq_nosync(pic32s->rx_irq);
224 	disable_irq_nosync(pic32s->tx_irq);
225 
226 	/* Show err message and abort xfer with err */
227 	dev_err(&pic32s->master->dev, "%s\n", msg);
228 	if (pic32s->master->cur_msg)
229 		pic32s->master->cur_msg->status = -EIO;
230 	complete(&pic32s->xfer_done);
231 }
232 
233 static irqreturn_t pic32_spi_fault_irq(int irq, void *dev_id)
234 {
235 	struct pic32_spi *pic32s = dev_id;
236 	u32 status;
237 
238 	status = readl(&pic32s->regs->status);
239 
240 	/* Error handling */
241 	if (status & (STAT_RX_OV | STAT_TX_UR)) {
242 		writel(STAT_RX_OV, &pic32s->regs->status_clr);
243 		writel(STAT_TX_UR, &pic32s->regs->status_clr);
244 		pic32_err_stop(pic32s, "err_irq: fifo ov/ur-run\n");
245 		return IRQ_HANDLED;
246 	}
247 
248 	if (status & STAT_FRM_ERR) {
249 		pic32_err_stop(pic32s, "err_irq: frame error");
250 		return IRQ_HANDLED;
251 	}
252 
253 	if (!pic32s->master->cur_msg) {
254 		pic32_err_stop(pic32s, "err_irq: no mesg");
255 		return IRQ_NONE;
256 	}
257 
258 	return IRQ_NONE;
259 }
260 
261 static irqreturn_t pic32_spi_rx_irq(int irq, void *dev_id)
262 {
263 	struct pic32_spi *pic32s = dev_id;
264 
265 	pic32s->rx_fifo(pic32s);
266 
267 	/* rx complete ? */
268 	if (pic32s->rx_end == pic32s->rx) {
269 		/* disable all interrupts */
270 		disable_irq_nosync(pic32s->fault_irq);
271 		disable_irq_nosync(pic32s->rx_irq);
272 
273 		/* complete current xfer */
274 		complete(&pic32s->xfer_done);
275 	}
276 
277 	return IRQ_HANDLED;
278 }
279 
280 static irqreturn_t pic32_spi_tx_irq(int irq, void *dev_id)
281 {
282 	struct pic32_spi *pic32s = dev_id;
283 
284 	pic32s->tx_fifo(pic32s);
285 
286 	/* tx complete? disable tx interrupt */
287 	if (pic32s->tx_end == pic32s->tx)
288 		disable_irq_nosync(pic32s->tx_irq);
289 
290 	return IRQ_HANDLED;
291 }
292 
293 static void pic32_spi_dma_rx_notify(void *data)
294 {
295 	struct pic32_spi *pic32s = data;
296 
297 	complete(&pic32s->xfer_done);
298 }
299 
300 static int pic32_spi_dma_transfer(struct pic32_spi *pic32s,
301 				  struct spi_transfer *xfer)
302 {
303 	struct spi_master *master = pic32s->master;
304 	struct dma_async_tx_descriptor *desc_rx;
305 	struct dma_async_tx_descriptor *desc_tx;
306 	dma_cookie_t cookie;
307 	int ret;
308 
309 	if (!master->dma_rx || !master->dma_tx)
310 		return -ENODEV;
311 
312 	desc_rx = dmaengine_prep_slave_sg(master->dma_rx,
313 					  xfer->rx_sg.sgl,
314 					  xfer->rx_sg.nents,
315 					  DMA_DEV_TO_MEM,
316 					  DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
317 	if (!desc_rx) {
318 		ret = -EINVAL;
319 		goto err_dma;
320 	}
321 
322 	desc_tx = dmaengine_prep_slave_sg(master->dma_tx,
323 					  xfer->tx_sg.sgl,
324 					  xfer->tx_sg.nents,
325 					  DMA_MEM_TO_DEV,
326 					  DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
327 	if (!desc_tx) {
328 		ret = -EINVAL;
329 		goto err_dma;
330 	}
331 
332 	/* Put callback on the RX transfer, that should finish last */
333 	desc_rx->callback = pic32_spi_dma_rx_notify;
334 	desc_rx->callback_param = pic32s;
335 
336 	cookie = dmaengine_submit(desc_rx);
337 	ret = dma_submit_error(cookie);
338 	if (ret)
339 		goto err_dma;
340 
341 	cookie = dmaengine_submit(desc_tx);
342 	ret = dma_submit_error(cookie);
343 	if (ret)
344 		goto err_dma_tx;
345 
346 	dma_async_issue_pending(master->dma_rx);
347 	dma_async_issue_pending(master->dma_tx);
348 
349 	return 0;
350 
351 err_dma_tx:
352 	dmaengine_terminate_all(master->dma_rx);
353 err_dma:
354 	return ret;
355 }
356 
357 static int pic32_spi_dma_config(struct pic32_spi *pic32s, u32 dma_width)
358 {
359 	int buf_offset = offsetof(struct pic32_spi_regs, buf);
360 	struct spi_master *master = pic32s->master;
361 	struct dma_slave_config cfg;
362 	int ret;
363 
364 	cfg.device_fc = true;
365 	cfg.src_addr = pic32s->dma_base + buf_offset;
366 	cfg.dst_addr = pic32s->dma_base + buf_offset;
367 	cfg.src_maxburst = pic32s->fifo_n_elm / 2; /* fill one-half */
368 	cfg.dst_maxburst = pic32s->fifo_n_elm / 2; /* drain one-half */
369 	cfg.src_addr_width = dma_width;
370 	cfg.dst_addr_width = dma_width;
371 	/* tx channel */
372 	cfg.slave_id = pic32s->tx_irq;
373 	cfg.direction = DMA_MEM_TO_DEV;
374 	ret = dmaengine_slave_config(master->dma_tx, &cfg);
375 	if (ret) {
376 		dev_err(&master->dev, "tx channel setup failed\n");
377 		return ret;
378 	}
379 	/* rx channel */
380 	cfg.slave_id = pic32s->rx_irq;
381 	cfg.direction = DMA_DEV_TO_MEM;
382 	ret = dmaengine_slave_config(master->dma_rx, &cfg);
383 	if (ret)
384 		dev_err(&master->dev, "rx channel setup failed\n");
385 
386 	return ret;
387 }
388 
389 static int pic32_spi_set_word_size(struct pic32_spi *pic32s, u8 bits_per_word)
390 {
391 	enum dma_slave_buswidth dmawidth;
392 	u32 buswidth, v;
393 
394 	switch (bits_per_word) {
395 	case 8:
396 		pic32s->rx_fifo = pic32_spi_rx_byte;
397 		pic32s->tx_fifo = pic32_spi_tx_byte;
398 		buswidth = PIC32_BPW_8;
399 		dmawidth = DMA_SLAVE_BUSWIDTH_1_BYTE;
400 		break;
401 	case 16:
402 		pic32s->rx_fifo = pic32_spi_rx_word;
403 		pic32s->tx_fifo = pic32_spi_tx_word;
404 		buswidth = PIC32_BPW_16;
405 		dmawidth = DMA_SLAVE_BUSWIDTH_2_BYTES;
406 		break;
407 	case 32:
408 		pic32s->rx_fifo = pic32_spi_rx_dword;
409 		pic32s->tx_fifo = pic32_spi_tx_dword;
410 		buswidth = PIC32_BPW_32;
411 		dmawidth = DMA_SLAVE_BUSWIDTH_4_BYTES;
412 		break;
413 	default:
414 		/* not supported */
415 		return -EINVAL;
416 	}
417 
418 	/* calculate maximum number of words fifos can hold */
419 	pic32s->fifo_n_elm = DIV_ROUND_UP(pic32s->fifo_n_byte,
420 					  bits_per_word / 8);
421 	/* set word size */
422 	v = readl(&pic32s->regs->ctrl);
423 	v &= ~(CTRL_BPW_MASK << CTRL_BPW_SHIFT);
424 	v |= buswidth << CTRL_BPW_SHIFT;
425 	writel(v, &pic32s->regs->ctrl);
426 
427 	/* re-configure dma width, if required */
428 	if (test_bit(PIC32F_DMA_PREP, &pic32s->flags))
429 		pic32_spi_dma_config(pic32s, dmawidth);
430 
431 	return 0;
432 }
433 
434 static int pic32_spi_prepare_hardware(struct spi_master *master)
435 {
436 	struct pic32_spi *pic32s = spi_master_get_devdata(master);
437 
438 	pic32_spi_enable(pic32s);
439 
440 	return 0;
441 }
442 
443 static int pic32_spi_prepare_message(struct spi_master *master,
444 				     struct spi_message *msg)
445 {
446 	struct pic32_spi *pic32s = spi_master_get_devdata(master);
447 	struct spi_device *spi = msg->spi;
448 	u32 val;
449 
450 	/* set device specific bits_per_word */
451 	if (pic32s->bits_per_word != spi->bits_per_word) {
452 		pic32_spi_set_word_size(pic32s, spi->bits_per_word);
453 		pic32s->bits_per_word = spi->bits_per_word;
454 	}
455 
456 	/* device specific speed change */
457 	if (pic32s->speed_hz != spi->max_speed_hz) {
458 		pic32_spi_set_clk_rate(pic32s, spi->max_speed_hz);
459 		pic32s->speed_hz = spi->max_speed_hz;
460 	}
461 
462 	/* device specific mode change */
463 	if (pic32s->mode != spi->mode) {
464 		val = readl(&pic32s->regs->ctrl);
465 		/* active low */
466 		if (spi->mode & SPI_CPOL)
467 			val |= CTRL_CKP;
468 		else
469 			val &= ~CTRL_CKP;
470 		/* tx on rising edge */
471 		if (spi->mode & SPI_CPHA)
472 			val &= ~CTRL_CKE;
473 		else
474 			val |= CTRL_CKE;
475 
476 		/* rx at end of tx */
477 		val |= CTRL_SMP;
478 		writel(val, &pic32s->regs->ctrl);
479 		pic32s->mode = spi->mode;
480 	}
481 
482 	return 0;
483 }
484 
485 static bool pic32_spi_can_dma(struct spi_master *master,
486 			      struct spi_device *spi,
487 			      struct spi_transfer *xfer)
488 {
489 	struct pic32_spi *pic32s = spi_master_get_devdata(master);
490 
491 	/* skip using DMA on small size transfer to avoid overhead.*/
492 	return (xfer->len >= PIC32_DMA_LEN_MIN) &&
493 	       test_bit(PIC32F_DMA_PREP, &pic32s->flags);
494 }
495 
496 static int pic32_spi_one_transfer(struct spi_master *master,
497 				  struct spi_device *spi,
498 				  struct spi_transfer *transfer)
499 {
500 	struct pic32_spi *pic32s;
501 	bool dma_issued = false;
502 	unsigned long timeout;
503 	int ret;
504 
505 	pic32s = spi_master_get_devdata(master);
506 
507 	/* handle transfer specific word size change */
508 	if (transfer->bits_per_word &&
509 	    (transfer->bits_per_word != pic32s->bits_per_word)) {
510 		ret = pic32_spi_set_word_size(pic32s, transfer->bits_per_word);
511 		if (ret)
512 			return ret;
513 		pic32s->bits_per_word = transfer->bits_per_word;
514 	}
515 
516 	/* handle transfer specific speed change */
517 	if (transfer->speed_hz && (transfer->speed_hz != pic32s->speed_hz)) {
518 		pic32_spi_set_clk_rate(pic32s, transfer->speed_hz);
519 		pic32s->speed_hz = transfer->speed_hz;
520 	}
521 
522 	reinit_completion(&pic32s->xfer_done);
523 
524 	/* transact by DMA mode */
525 	if (transfer->rx_sg.nents && transfer->tx_sg.nents) {
526 		ret = pic32_spi_dma_transfer(pic32s, transfer);
527 		if (ret) {
528 			dev_err(&spi->dev, "dma submit error\n");
529 			return ret;
530 		}
531 
532 		/* DMA issued */
533 		dma_issued = true;
534 	} else {
535 		/* set current transfer information */
536 		pic32s->tx = (const void *)transfer->tx_buf;
537 		pic32s->rx = (const void *)transfer->rx_buf;
538 		pic32s->tx_end = pic32s->tx + transfer->len;
539 		pic32s->rx_end = pic32s->rx + transfer->len;
540 		pic32s->len = transfer->len;
541 
542 		/* transact by interrupt driven PIO */
543 		enable_irq(pic32s->fault_irq);
544 		enable_irq(pic32s->rx_irq);
545 		enable_irq(pic32s->tx_irq);
546 	}
547 
548 	/* wait for completion */
549 	timeout = wait_for_completion_timeout(&pic32s->xfer_done, 2 * HZ);
550 	if (timeout == 0) {
551 		dev_err(&spi->dev, "wait error/timedout\n");
552 		if (dma_issued) {
553 			dmaengine_terminate_all(master->dma_rx);
554 			dmaengine_terminate_all(master->dma_tx);
555 		}
556 		ret = -ETIMEDOUT;
557 	} else {
558 		ret = 0;
559 	}
560 
561 	return ret;
562 }
563 
564 static int pic32_spi_unprepare_message(struct spi_master *master,
565 				       struct spi_message *msg)
566 {
567 	/* nothing to do */
568 	return 0;
569 }
570 
571 static int pic32_spi_unprepare_hardware(struct spi_master *master)
572 {
573 	struct pic32_spi *pic32s = spi_master_get_devdata(master);
574 
575 	pic32_spi_disable(pic32s);
576 
577 	return 0;
578 }
579 
580 /* This may be called multiple times by same spi dev */
581 static int pic32_spi_setup(struct spi_device *spi)
582 {
583 	if (!spi->max_speed_hz) {
584 		dev_err(&spi->dev, "No max speed HZ parameter\n");
585 		return -EINVAL;
586 	}
587 
588 	/* PIC32 spi controller can drive /CS during transfer depending
589 	 * on tx fifo fill-level. /CS will stay asserted as long as TX
590 	 * fifo is non-empty, else will be deasserted indicating
591 	 * completion of the ongoing transfer. This might result into
592 	 * unreliable/erroneous SPI transactions.
593 	 * To avoid that we will always handle /CS by toggling GPIO.
594 	 */
595 	if (!gpio_is_valid(spi->cs_gpio))
596 		return -EINVAL;
597 
598 	gpio_direction_output(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
599 
600 	return 0;
601 }
602 
603 static void pic32_spi_cleanup(struct spi_device *spi)
604 {
605 	/* de-activate cs-gpio */
606 	gpio_direction_output(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
607 }
608 
609 static int pic32_spi_dma_prep(struct pic32_spi *pic32s, struct device *dev)
610 {
611 	struct spi_master *master = pic32s->master;
612 	int ret = 0;
613 
614 	master->dma_rx = dma_request_chan(dev, "spi-rx");
615 	if (IS_ERR(master->dma_rx)) {
616 		if (PTR_ERR(master->dma_rx) == -EPROBE_DEFER)
617 			ret = -EPROBE_DEFER;
618 		else
619 			dev_warn(dev, "RX channel not found.\n");
620 
621 		master->dma_rx = NULL;
622 		goto out_err;
623 	}
624 
625 	master->dma_tx = dma_request_chan(dev, "spi-tx");
626 	if (IS_ERR(master->dma_tx)) {
627 		if (PTR_ERR(master->dma_tx) == -EPROBE_DEFER)
628 			ret = -EPROBE_DEFER;
629 		else
630 			dev_warn(dev, "TX channel not found.\n");
631 
632 		master->dma_tx = NULL;
633 		goto out_err;
634 	}
635 
636 	if (pic32_spi_dma_config(pic32s, DMA_SLAVE_BUSWIDTH_1_BYTE))
637 		goto out_err;
638 
639 	/* DMA chnls allocated and prepared */
640 	set_bit(PIC32F_DMA_PREP, &pic32s->flags);
641 
642 	return 0;
643 
644 out_err:
645 	if (master->dma_rx) {
646 		dma_release_channel(master->dma_rx);
647 		master->dma_rx = NULL;
648 	}
649 
650 	if (master->dma_tx) {
651 		dma_release_channel(master->dma_tx);
652 		master->dma_tx = NULL;
653 	}
654 
655 	return ret;
656 }
657 
658 static void pic32_spi_dma_unprep(struct pic32_spi *pic32s)
659 {
660 	if (!test_bit(PIC32F_DMA_PREP, &pic32s->flags))
661 		return;
662 
663 	clear_bit(PIC32F_DMA_PREP, &pic32s->flags);
664 	if (pic32s->master->dma_rx)
665 		dma_release_channel(pic32s->master->dma_rx);
666 
667 	if (pic32s->master->dma_tx)
668 		dma_release_channel(pic32s->master->dma_tx);
669 }
670 
671 static void pic32_spi_hw_init(struct pic32_spi *pic32s)
672 {
673 	u32 ctrl;
674 
675 	/* disable hardware */
676 	pic32_spi_disable(pic32s);
677 
678 	ctrl = readl(&pic32s->regs->ctrl);
679 	/* enable enhanced fifo of 128bit deep */
680 	ctrl |= CTRL_ENHBUF;
681 	pic32s->fifo_n_byte = 16;
682 
683 	/* disable framing mode */
684 	ctrl &= ~CTRL_FRMEN;
685 
686 	/* enable master mode while disabled */
687 	ctrl |= CTRL_MSTEN;
688 
689 	/* set tx fifo threshold interrupt */
690 	ctrl &= ~(0x3 << CTRL_TX_INT_SHIFT);
691 	ctrl |= (TX_FIFO_HALF_EMPTY << CTRL_TX_INT_SHIFT);
692 
693 	/* set rx fifo threshold interrupt */
694 	ctrl &= ~(0x3 << CTRL_RX_INT_SHIFT);
695 	ctrl |= (RX_FIFO_NOT_EMPTY << CTRL_RX_INT_SHIFT);
696 
697 	/* select clk source */
698 	ctrl &= ~CTRL_MCLKSEL;
699 
700 	/* set manual /CS mode */
701 	ctrl &= ~CTRL_MSSEN;
702 
703 	writel(ctrl, &pic32s->regs->ctrl);
704 
705 	/* enable error reporting */
706 	ctrl = CTRL2_TX_UR_EN | CTRL2_RX_OV_EN | CTRL2_FRM_ERR_EN;
707 	writel(ctrl, &pic32s->regs->ctrl2_set);
708 }
709 
710 static int pic32_spi_hw_probe(struct platform_device *pdev,
711 			      struct pic32_spi *pic32s)
712 {
713 	struct resource *mem;
714 	int ret;
715 
716 	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
717 	pic32s->regs = devm_ioremap_resource(&pdev->dev, mem);
718 	if (IS_ERR(pic32s->regs))
719 		return PTR_ERR(pic32s->regs);
720 
721 	pic32s->dma_base = mem->start;
722 
723 	/* get irq resources: err-irq, rx-irq, tx-irq */
724 	pic32s->fault_irq = platform_get_irq_byname(pdev, "fault");
725 	if (pic32s->fault_irq < 0)
726 		return pic32s->fault_irq;
727 
728 	pic32s->rx_irq = platform_get_irq_byname(pdev, "rx");
729 	if (pic32s->rx_irq < 0)
730 		return pic32s->rx_irq;
731 
732 	pic32s->tx_irq = platform_get_irq_byname(pdev, "tx");
733 	if (pic32s->tx_irq < 0)
734 		return pic32s->tx_irq;
735 
736 	/* get clock */
737 	pic32s->clk = devm_clk_get(&pdev->dev, "mck0");
738 	if (IS_ERR(pic32s->clk)) {
739 		dev_err(&pdev->dev, "clk not found\n");
740 		ret = PTR_ERR(pic32s->clk);
741 		goto err_unmap_mem;
742 	}
743 
744 	ret = clk_prepare_enable(pic32s->clk);
745 	if (ret)
746 		goto err_unmap_mem;
747 
748 	pic32_spi_hw_init(pic32s);
749 
750 	return 0;
751 
752 err_unmap_mem:
753 	dev_err(&pdev->dev, "%s failed, err %d\n", __func__, ret);
754 	return ret;
755 }
756 
757 static int pic32_spi_probe(struct platform_device *pdev)
758 {
759 	struct spi_master *master;
760 	struct pic32_spi *pic32s;
761 	int ret;
762 
763 	master = spi_alloc_master(&pdev->dev, sizeof(*pic32s));
764 	if (!master)
765 		return -ENOMEM;
766 
767 	pic32s = spi_master_get_devdata(master);
768 	pic32s->master = master;
769 
770 	ret = pic32_spi_hw_probe(pdev, pic32s);
771 	if (ret)
772 		goto err_master;
773 
774 	master->dev.of_node	= pdev->dev.of_node;
775 	master->mode_bits	= SPI_MODE_3 | SPI_MODE_0 | SPI_CS_HIGH;
776 	master->num_chipselect	= 1; /* single chip-select */
777 	master->max_speed_hz	= clk_get_rate(pic32s->clk);
778 	master->setup		= pic32_spi_setup;
779 	master->cleanup		= pic32_spi_cleanup;
780 	master->flags		= SPI_MASTER_MUST_TX | SPI_MASTER_MUST_RX;
781 	master->bits_per_word_mask	= SPI_BPW_MASK(8) | SPI_BPW_MASK(16) |
782 					  SPI_BPW_MASK(32);
783 	master->transfer_one		= pic32_spi_one_transfer;
784 	master->prepare_message		= pic32_spi_prepare_message;
785 	master->unprepare_message	= pic32_spi_unprepare_message;
786 	master->prepare_transfer_hardware	= pic32_spi_prepare_hardware;
787 	master->unprepare_transfer_hardware	= pic32_spi_unprepare_hardware;
788 
789 	/* optional DMA support */
790 	ret = pic32_spi_dma_prep(pic32s, &pdev->dev);
791 	if (ret)
792 		goto err_bailout;
793 
794 	if (test_bit(PIC32F_DMA_PREP, &pic32s->flags))
795 		master->can_dma	= pic32_spi_can_dma;
796 
797 	init_completion(&pic32s->xfer_done);
798 	pic32s->mode = -1;
799 
800 	/* install irq handlers (with irq-disabled) */
801 	irq_set_status_flags(pic32s->fault_irq, IRQ_NOAUTOEN);
802 	ret = devm_request_irq(&pdev->dev, pic32s->fault_irq,
803 			       pic32_spi_fault_irq, IRQF_NO_THREAD,
804 			       dev_name(&pdev->dev), pic32s);
805 	if (ret < 0) {
806 		dev_err(&pdev->dev, "request fault-irq %d\n", pic32s->rx_irq);
807 		goto err_bailout;
808 	}
809 
810 	/* receive interrupt handler */
811 	irq_set_status_flags(pic32s->rx_irq, IRQ_NOAUTOEN);
812 	ret = devm_request_irq(&pdev->dev, pic32s->rx_irq,
813 			       pic32_spi_rx_irq, IRQF_NO_THREAD,
814 			       dev_name(&pdev->dev), pic32s);
815 	if (ret < 0) {
816 		dev_err(&pdev->dev, "request rx-irq %d\n", pic32s->rx_irq);
817 		goto err_bailout;
818 	}
819 
820 	/* transmit interrupt handler */
821 	irq_set_status_flags(pic32s->tx_irq, IRQ_NOAUTOEN);
822 	ret = devm_request_irq(&pdev->dev, pic32s->tx_irq,
823 			       pic32_spi_tx_irq, IRQF_NO_THREAD,
824 			       dev_name(&pdev->dev), pic32s);
825 	if (ret < 0) {
826 		dev_err(&pdev->dev, "request tx-irq %d\n", pic32s->tx_irq);
827 		goto err_bailout;
828 	}
829 
830 	/* register master */
831 	ret = devm_spi_register_master(&pdev->dev, master);
832 	if (ret) {
833 		dev_err(&master->dev, "failed registering spi master\n");
834 		goto err_bailout;
835 	}
836 
837 	platform_set_drvdata(pdev, pic32s);
838 
839 	return 0;
840 
841 err_bailout:
842 	pic32_spi_dma_unprep(pic32s);
843 	clk_disable_unprepare(pic32s->clk);
844 err_master:
845 	spi_master_put(master);
846 	return ret;
847 }
848 
849 static int pic32_spi_remove(struct platform_device *pdev)
850 {
851 	struct pic32_spi *pic32s;
852 
853 	pic32s = platform_get_drvdata(pdev);
854 	pic32_spi_disable(pic32s);
855 	clk_disable_unprepare(pic32s->clk);
856 	pic32_spi_dma_unprep(pic32s);
857 
858 	return 0;
859 }
860 
861 static const struct of_device_id pic32_spi_of_match[] = {
862 	{.compatible = "microchip,pic32mzda-spi",},
863 	{},
864 };
865 MODULE_DEVICE_TABLE(of, pic32_spi_of_match);
866 
867 static struct platform_driver pic32_spi_driver = {
868 	.driver = {
869 		.name = "spi-pic32",
870 		.of_match_table = of_match_ptr(pic32_spi_of_match),
871 	},
872 	.probe = pic32_spi_probe,
873 	.remove = pic32_spi_remove,
874 };
875 
876 module_platform_driver(pic32_spi_driver);
877 
878 MODULE_AUTHOR("Purna Chandra Mandal <purna.mandal@microchip.com>");
879 MODULE_DESCRIPTION("Microchip SPI driver for PIC32 SPI controller.");
880 MODULE_LICENSE("GPL v2");
881