1 // SPDX-License-Identifier: GPL-2.0-only 2 // 3 // Driver for Cadence QSPI Controller 4 // 5 // Copyright Altera Corporation (C) 2012-2014. All rights reserved. 6 // Copyright Intel Corporation (C) 2019-2020. All rights reserved. 7 // Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com 8 9 #include <linux/clk.h> 10 #include <linux/completion.h> 11 #include <linux/delay.h> 12 #include <linux/dma-mapping.h> 13 #include <linux/dmaengine.h> 14 #include <linux/err.h> 15 #include <linux/errno.h> 16 #include <linux/firmware/xlnx-zynqmp.h> 17 #include <linux/interrupt.h> 18 #include <linux/io.h> 19 #include <linux/iopoll.h> 20 #include <linux/jiffies.h> 21 #include <linux/kernel.h> 22 #include <linux/log2.h> 23 #include <linux/module.h> 24 #include <linux/of_device.h> 25 #include <linux/of.h> 26 #include <linux/platform_device.h> 27 #include <linux/pm_runtime.h> 28 #include <linux/reset.h> 29 #include <linux/sched.h> 30 #include <linux/spi/spi.h> 31 #include <linux/spi/spi-mem.h> 32 #include <linux/timer.h> 33 34 #define CQSPI_NAME "cadence-qspi" 35 #define CQSPI_MAX_CHIPSELECT 16 36 37 /* Quirks */ 38 #define CQSPI_NEEDS_WR_DELAY BIT(0) 39 #define CQSPI_DISABLE_DAC_MODE BIT(1) 40 #define CQSPI_SUPPORT_EXTERNAL_DMA BIT(2) 41 #define CQSPI_NO_SUPPORT_WR_COMPLETION BIT(3) 42 43 /* Capabilities */ 44 #define CQSPI_SUPPORTS_OCTAL BIT(0) 45 46 struct cqspi_st; 47 48 struct cqspi_flash_pdata { 49 struct cqspi_st *cqspi; 50 u32 clk_rate; 51 u32 read_delay; 52 u32 tshsl_ns; 53 u32 tsd2d_ns; 54 u32 tchsh_ns; 55 u32 tslch_ns; 56 u8 inst_width; 57 u8 addr_width; 58 u8 data_width; 59 bool dtr; 60 u8 cs; 61 }; 62 63 struct cqspi_st { 64 struct platform_device *pdev; 65 66 struct clk *clk; 67 unsigned int sclk; 68 69 void __iomem *iobase; 70 void __iomem *ahb_base; 71 resource_size_t ahb_size; 72 struct completion transfer_complete; 73 74 struct dma_chan *rx_chan; 75 struct completion rx_dma_complete; 76 dma_addr_t mmap_phys_base; 77 78 int current_cs; 79 unsigned long master_ref_clk_hz; 80 bool is_decoded_cs; 81 u32 fifo_depth; 82 u32 fifo_width; 83 u32 num_chipselect; 84 bool rclk_en; 85 u32 trigger_address; 86 u32 wr_delay; 87 bool use_direct_mode; 88 struct cqspi_flash_pdata f_pdata[CQSPI_MAX_CHIPSELECT]; 89 bool use_dma_read; 90 u32 pd_dev_id; 91 bool wr_completion; 92 }; 93 94 struct cqspi_driver_platdata { 95 u32 hwcaps_mask; 96 u8 quirks; 97 int (*indirect_read_dma)(struct cqspi_flash_pdata *f_pdata, 98 u_char *rxbuf, loff_t from_addr, size_t n_rx); 99 u32 (*get_dma_status)(struct cqspi_st *cqspi); 100 }; 101 102 /* Operation timeout value */ 103 #define CQSPI_TIMEOUT_MS 500 104 #define CQSPI_READ_TIMEOUT_MS 10 105 106 #define CQSPI_DUMMY_CLKS_PER_BYTE 8 107 #define CQSPI_DUMMY_BYTES_MAX 4 108 #define CQSPI_DUMMY_CLKS_MAX 31 109 110 #define CQSPI_STIG_DATA_LEN_MAX 8 111 112 /* Register map */ 113 #define CQSPI_REG_CONFIG 0x00 114 #define CQSPI_REG_CONFIG_ENABLE_MASK BIT(0) 115 #define CQSPI_REG_CONFIG_ENB_DIR_ACC_CTRL BIT(7) 116 #define CQSPI_REG_CONFIG_DECODE_MASK BIT(9) 117 #define CQSPI_REG_CONFIG_CHIPSELECT_LSB 10 118 #define CQSPI_REG_CONFIG_DMA_MASK BIT(15) 119 #define CQSPI_REG_CONFIG_BAUD_LSB 19 120 #define CQSPI_REG_CONFIG_DTR_PROTO BIT(24) 121 #define CQSPI_REG_CONFIG_DUAL_OPCODE BIT(30) 122 #define CQSPI_REG_CONFIG_IDLE_LSB 31 123 #define CQSPI_REG_CONFIG_CHIPSELECT_MASK 0xF 124 #define CQSPI_REG_CONFIG_BAUD_MASK 0xF 125 126 #define CQSPI_REG_RD_INSTR 0x04 127 #define CQSPI_REG_RD_INSTR_OPCODE_LSB 0 128 #define CQSPI_REG_RD_INSTR_TYPE_INSTR_LSB 8 129 #define CQSPI_REG_RD_INSTR_TYPE_ADDR_LSB 12 130 #define CQSPI_REG_RD_INSTR_TYPE_DATA_LSB 16 131 #define CQSPI_REG_RD_INSTR_MODE_EN_LSB 20 132 #define CQSPI_REG_RD_INSTR_DUMMY_LSB 24 133 #define CQSPI_REG_RD_INSTR_TYPE_INSTR_MASK 0x3 134 #define CQSPI_REG_RD_INSTR_TYPE_ADDR_MASK 0x3 135 #define CQSPI_REG_RD_INSTR_TYPE_DATA_MASK 0x3 136 #define CQSPI_REG_RD_INSTR_DUMMY_MASK 0x1F 137 138 #define CQSPI_REG_WR_INSTR 0x08 139 #define CQSPI_REG_WR_INSTR_OPCODE_LSB 0 140 #define CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB 12 141 #define CQSPI_REG_WR_INSTR_TYPE_DATA_LSB 16 142 143 #define CQSPI_REG_DELAY 0x0C 144 #define CQSPI_REG_DELAY_TSLCH_LSB 0 145 #define CQSPI_REG_DELAY_TCHSH_LSB 8 146 #define CQSPI_REG_DELAY_TSD2D_LSB 16 147 #define CQSPI_REG_DELAY_TSHSL_LSB 24 148 #define CQSPI_REG_DELAY_TSLCH_MASK 0xFF 149 #define CQSPI_REG_DELAY_TCHSH_MASK 0xFF 150 #define CQSPI_REG_DELAY_TSD2D_MASK 0xFF 151 #define CQSPI_REG_DELAY_TSHSL_MASK 0xFF 152 153 #define CQSPI_REG_READCAPTURE 0x10 154 #define CQSPI_REG_READCAPTURE_BYPASS_LSB 0 155 #define CQSPI_REG_READCAPTURE_DELAY_LSB 1 156 #define CQSPI_REG_READCAPTURE_DELAY_MASK 0xF 157 158 #define CQSPI_REG_SIZE 0x14 159 #define CQSPI_REG_SIZE_ADDRESS_LSB 0 160 #define CQSPI_REG_SIZE_PAGE_LSB 4 161 #define CQSPI_REG_SIZE_BLOCK_LSB 16 162 #define CQSPI_REG_SIZE_ADDRESS_MASK 0xF 163 #define CQSPI_REG_SIZE_PAGE_MASK 0xFFF 164 #define CQSPI_REG_SIZE_BLOCK_MASK 0x3F 165 166 #define CQSPI_REG_SRAMPARTITION 0x18 167 #define CQSPI_REG_INDIRECTTRIGGER 0x1C 168 169 #define CQSPI_REG_DMA 0x20 170 #define CQSPI_REG_DMA_SINGLE_LSB 0 171 #define CQSPI_REG_DMA_BURST_LSB 8 172 #define CQSPI_REG_DMA_SINGLE_MASK 0xFF 173 #define CQSPI_REG_DMA_BURST_MASK 0xFF 174 175 #define CQSPI_REG_REMAP 0x24 176 #define CQSPI_REG_MODE_BIT 0x28 177 178 #define CQSPI_REG_SDRAMLEVEL 0x2C 179 #define CQSPI_REG_SDRAMLEVEL_RD_LSB 0 180 #define CQSPI_REG_SDRAMLEVEL_WR_LSB 16 181 #define CQSPI_REG_SDRAMLEVEL_RD_MASK 0xFFFF 182 #define CQSPI_REG_SDRAMLEVEL_WR_MASK 0xFFFF 183 184 #define CQSPI_REG_WR_COMPLETION_CTRL 0x38 185 #define CQSPI_REG_WR_DISABLE_AUTO_POLL BIT(14) 186 187 #define CQSPI_REG_IRQSTATUS 0x40 188 #define CQSPI_REG_IRQMASK 0x44 189 190 #define CQSPI_REG_INDIRECTRD 0x60 191 #define CQSPI_REG_INDIRECTRD_START_MASK BIT(0) 192 #define CQSPI_REG_INDIRECTRD_CANCEL_MASK BIT(1) 193 #define CQSPI_REG_INDIRECTRD_DONE_MASK BIT(5) 194 195 #define CQSPI_REG_INDIRECTRDWATERMARK 0x64 196 #define CQSPI_REG_INDIRECTRDSTARTADDR 0x68 197 #define CQSPI_REG_INDIRECTRDBYTES 0x6C 198 199 #define CQSPI_REG_CMDCTRL 0x90 200 #define CQSPI_REG_CMDCTRL_EXECUTE_MASK BIT(0) 201 #define CQSPI_REG_CMDCTRL_INPROGRESS_MASK BIT(1) 202 #define CQSPI_REG_CMDCTRL_DUMMY_LSB 7 203 #define CQSPI_REG_CMDCTRL_WR_BYTES_LSB 12 204 #define CQSPI_REG_CMDCTRL_WR_EN_LSB 15 205 #define CQSPI_REG_CMDCTRL_ADD_BYTES_LSB 16 206 #define CQSPI_REG_CMDCTRL_ADDR_EN_LSB 19 207 #define CQSPI_REG_CMDCTRL_RD_BYTES_LSB 20 208 #define CQSPI_REG_CMDCTRL_RD_EN_LSB 23 209 #define CQSPI_REG_CMDCTRL_OPCODE_LSB 24 210 #define CQSPI_REG_CMDCTRL_WR_BYTES_MASK 0x7 211 #define CQSPI_REG_CMDCTRL_ADD_BYTES_MASK 0x3 212 #define CQSPI_REG_CMDCTRL_RD_BYTES_MASK 0x7 213 #define CQSPI_REG_CMDCTRL_DUMMY_MASK 0x1F 214 215 #define CQSPI_REG_INDIRECTWR 0x70 216 #define CQSPI_REG_INDIRECTWR_START_MASK BIT(0) 217 #define CQSPI_REG_INDIRECTWR_CANCEL_MASK BIT(1) 218 #define CQSPI_REG_INDIRECTWR_DONE_MASK BIT(5) 219 220 #define CQSPI_REG_INDIRECTWRWATERMARK 0x74 221 #define CQSPI_REG_INDIRECTWRSTARTADDR 0x78 222 #define CQSPI_REG_INDIRECTWRBYTES 0x7C 223 224 #define CQSPI_REG_INDTRIG_ADDRRANGE 0x80 225 226 #define CQSPI_REG_CMDADDRESS 0x94 227 #define CQSPI_REG_CMDREADDATALOWER 0xA0 228 #define CQSPI_REG_CMDREADDATAUPPER 0xA4 229 #define CQSPI_REG_CMDWRITEDATALOWER 0xA8 230 #define CQSPI_REG_CMDWRITEDATAUPPER 0xAC 231 232 #define CQSPI_REG_POLLING_STATUS 0xB0 233 #define CQSPI_REG_POLLING_STATUS_DUMMY_LSB 16 234 235 #define CQSPI_REG_OP_EXT_LOWER 0xE0 236 #define CQSPI_REG_OP_EXT_READ_LSB 24 237 #define CQSPI_REG_OP_EXT_WRITE_LSB 16 238 #define CQSPI_REG_OP_EXT_STIG_LSB 0 239 240 #define CQSPI_REG_VERSAL_DMA_SRC_ADDR 0x1000 241 242 #define CQSPI_REG_VERSAL_DMA_DST_ADDR 0x1800 243 #define CQSPI_REG_VERSAL_DMA_DST_SIZE 0x1804 244 245 #define CQSPI_REG_VERSAL_DMA_DST_CTRL 0x180C 246 247 #define CQSPI_REG_VERSAL_DMA_DST_I_STS 0x1814 248 #define CQSPI_REG_VERSAL_DMA_DST_I_EN 0x1818 249 #define CQSPI_REG_VERSAL_DMA_DST_I_DIS 0x181C 250 #define CQSPI_REG_VERSAL_DMA_DST_DONE_MASK BIT(1) 251 252 #define CQSPI_REG_VERSAL_DMA_DST_ADDR_MSB 0x1828 253 254 #define CQSPI_REG_VERSAL_DMA_DST_CTRL_VAL 0xF43FFA00 255 #define CQSPI_REG_VERSAL_ADDRRANGE_WIDTH_VAL 0x6 256 257 /* Interrupt status bits */ 258 #define CQSPI_REG_IRQ_MODE_ERR BIT(0) 259 #define CQSPI_REG_IRQ_UNDERFLOW BIT(1) 260 #define CQSPI_REG_IRQ_IND_COMP BIT(2) 261 #define CQSPI_REG_IRQ_IND_RD_REJECT BIT(3) 262 #define CQSPI_REG_IRQ_WR_PROTECTED_ERR BIT(4) 263 #define CQSPI_REG_IRQ_ILLEGAL_AHB_ERR BIT(5) 264 #define CQSPI_REG_IRQ_WATERMARK BIT(6) 265 #define CQSPI_REG_IRQ_IND_SRAM_FULL BIT(12) 266 267 #define CQSPI_IRQ_MASK_RD (CQSPI_REG_IRQ_WATERMARK | \ 268 CQSPI_REG_IRQ_IND_SRAM_FULL | \ 269 CQSPI_REG_IRQ_IND_COMP) 270 271 #define CQSPI_IRQ_MASK_WR (CQSPI_REG_IRQ_IND_COMP | \ 272 CQSPI_REG_IRQ_WATERMARK | \ 273 CQSPI_REG_IRQ_UNDERFLOW) 274 275 #define CQSPI_IRQ_STATUS_MASK 0x1FFFF 276 #define CQSPI_DMA_UNALIGN 0x3 277 278 #define CQSPI_REG_VERSAL_DMA_VAL 0x602 279 280 static int cqspi_wait_for_bit(void __iomem *reg, const u32 mask, bool clr) 281 { 282 u32 val; 283 284 return readl_relaxed_poll_timeout(reg, val, 285 (((clr ? ~val : val) & mask) == mask), 286 10, CQSPI_TIMEOUT_MS * 1000); 287 } 288 289 static bool cqspi_is_idle(struct cqspi_st *cqspi) 290 { 291 u32 reg = readl(cqspi->iobase + CQSPI_REG_CONFIG); 292 293 return reg & (1UL << CQSPI_REG_CONFIG_IDLE_LSB); 294 } 295 296 static u32 cqspi_get_rd_sram_level(struct cqspi_st *cqspi) 297 { 298 u32 reg = readl(cqspi->iobase + CQSPI_REG_SDRAMLEVEL); 299 300 reg >>= CQSPI_REG_SDRAMLEVEL_RD_LSB; 301 return reg & CQSPI_REG_SDRAMLEVEL_RD_MASK; 302 } 303 304 static u32 cqspi_get_versal_dma_status(struct cqspi_st *cqspi) 305 { 306 u32 dma_status; 307 308 dma_status = readl(cqspi->iobase + 309 CQSPI_REG_VERSAL_DMA_DST_I_STS); 310 writel(dma_status, cqspi->iobase + 311 CQSPI_REG_VERSAL_DMA_DST_I_STS); 312 313 return dma_status & CQSPI_REG_VERSAL_DMA_DST_DONE_MASK; 314 } 315 316 static irqreturn_t cqspi_irq_handler(int this_irq, void *dev) 317 { 318 struct cqspi_st *cqspi = dev; 319 unsigned int irq_status; 320 struct device *device = &cqspi->pdev->dev; 321 const struct cqspi_driver_platdata *ddata; 322 323 ddata = of_device_get_match_data(device); 324 325 /* Read interrupt status */ 326 irq_status = readl(cqspi->iobase + CQSPI_REG_IRQSTATUS); 327 328 /* Clear interrupt */ 329 writel(irq_status, cqspi->iobase + CQSPI_REG_IRQSTATUS); 330 331 if (cqspi->use_dma_read && ddata && ddata->get_dma_status) { 332 if (ddata->get_dma_status(cqspi)) { 333 complete(&cqspi->transfer_complete); 334 return IRQ_HANDLED; 335 } 336 } 337 338 irq_status &= CQSPI_IRQ_MASK_RD | CQSPI_IRQ_MASK_WR; 339 340 if (irq_status) 341 complete(&cqspi->transfer_complete); 342 343 return IRQ_HANDLED; 344 } 345 346 static unsigned int cqspi_calc_rdreg(struct cqspi_flash_pdata *f_pdata) 347 { 348 u32 rdreg = 0; 349 350 rdreg |= f_pdata->inst_width << CQSPI_REG_RD_INSTR_TYPE_INSTR_LSB; 351 rdreg |= f_pdata->addr_width << CQSPI_REG_RD_INSTR_TYPE_ADDR_LSB; 352 rdreg |= f_pdata->data_width << CQSPI_REG_RD_INSTR_TYPE_DATA_LSB; 353 354 return rdreg; 355 } 356 357 static unsigned int cqspi_calc_dummy(const struct spi_mem_op *op, bool dtr) 358 { 359 unsigned int dummy_clk; 360 361 if (!op->dummy.nbytes) 362 return 0; 363 364 dummy_clk = op->dummy.nbytes * (8 / op->dummy.buswidth); 365 if (dtr) 366 dummy_clk /= 2; 367 368 return dummy_clk; 369 } 370 371 static int cqspi_set_protocol(struct cqspi_flash_pdata *f_pdata, 372 const struct spi_mem_op *op) 373 { 374 /* 375 * For an op to be DTR, cmd phase along with every other non-empty 376 * phase should have dtr field set to 1. If an op phase has zero 377 * nbytes, ignore its dtr field; otherwise, check its dtr field. 378 */ 379 f_pdata->dtr = op->cmd.dtr && 380 (!op->addr.nbytes || op->addr.dtr) && 381 (!op->data.nbytes || op->data.dtr); 382 383 f_pdata->inst_width = 0; 384 if (op->cmd.buswidth) 385 f_pdata->inst_width = ilog2(op->cmd.buswidth); 386 387 f_pdata->addr_width = 0; 388 if (op->addr.buswidth) 389 f_pdata->addr_width = ilog2(op->addr.buswidth); 390 391 f_pdata->data_width = 0; 392 if (op->data.buswidth) 393 f_pdata->data_width = ilog2(op->data.buswidth); 394 395 /* Right now we only support 8-8-8 DTR mode. */ 396 if (f_pdata->dtr) { 397 switch (op->cmd.buswidth) { 398 case 0: 399 case 8: 400 break; 401 default: 402 return -EINVAL; 403 } 404 405 switch (op->addr.buswidth) { 406 case 0: 407 case 8: 408 break; 409 default: 410 return -EINVAL; 411 } 412 413 switch (op->data.buswidth) { 414 case 0: 415 case 8: 416 break; 417 default: 418 return -EINVAL; 419 } 420 } 421 422 return 0; 423 } 424 425 static int cqspi_wait_idle(struct cqspi_st *cqspi) 426 { 427 const unsigned int poll_idle_retry = 3; 428 unsigned int count = 0; 429 unsigned long timeout; 430 431 timeout = jiffies + msecs_to_jiffies(CQSPI_TIMEOUT_MS); 432 while (1) { 433 /* 434 * Read few times in succession to ensure the controller 435 * is indeed idle, that is, the bit does not transition 436 * low again. 437 */ 438 if (cqspi_is_idle(cqspi)) 439 count++; 440 else 441 count = 0; 442 443 if (count >= poll_idle_retry) 444 return 0; 445 446 if (time_after(jiffies, timeout)) { 447 /* Timeout, in busy mode. */ 448 dev_err(&cqspi->pdev->dev, 449 "QSPI is still busy after %dms timeout.\n", 450 CQSPI_TIMEOUT_MS); 451 return -ETIMEDOUT; 452 } 453 454 cpu_relax(); 455 } 456 } 457 458 static int cqspi_exec_flash_cmd(struct cqspi_st *cqspi, unsigned int reg) 459 { 460 void __iomem *reg_base = cqspi->iobase; 461 int ret; 462 463 /* Write the CMDCTRL without start execution. */ 464 writel(reg, reg_base + CQSPI_REG_CMDCTRL); 465 /* Start execute */ 466 reg |= CQSPI_REG_CMDCTRL_EXECUTE_MASK; 467 writel(reg, reg_base + CQSPI_REG_CMDCTRL); 468 469 /* Polling for completion. */ 470 ret = cqspi_wait_for_bit(reg_base + CQSPI_REG_CMDCTRL, 471 CQSPI_REG_CMDCTRL_INPROGRESS_MASK, 1); 472 if (ret) { 473 dev_err(&cqspi->pdev->dev, 474 "Flash command execution timed out.\n"); 475 return ret; 476 } 477 478 /* Polling QSPI idle status. */ 479 return cqspi_wait_idle(cqspi); 480 } 481 482 static int cqspi_setup_opcode_ext(struct cqspi_flash_pdata *f_pdata, 483 const struct spi_mem_op *op, 484 unsigned int shift) 485 { 486 struct cqspi_st *cqspi = f_pdata->cqspi; 487 void __iomem *reg_base = cqspi->iobase; 488 unsigned int reg; 489 u8 ext; 490 491 if (op->cmd.nbytes != 2) 492 return -EINVAL; 493 494 /* Opcode extension is the LSB. */ 495 ext = op->cmd.opcode & 0xff; 496 497 reg = readl(reg_base + CQSPI_REG_OP_EXT_LOWER); 498 reg &= ~(0xff << shift); 499 reg |= ext << shift; 500 writel(reg, reg_base + CQSPI_REG_OP_EXT_LOWER); 501 502 return 0; 503 } 504 505 static int cqspi_enable_dtr(struct cqspi_flash_pdata *f_pdata, 506 const struct spi_mem_op *op, unsigned int shift, 507 bool enable) 508 { 509 struct cqspi_st *cqspi = f_pdata->cqspi; 510 void __iomem *reg_base = cqspi->iobase; 511 unsigned int reg; 512 int ret; 513 514 reg = readl(reg_base + CQSPI_REG_CONFIG); 515 516 /* 517 * We enable dual byte opcode here. The callers have to set up the 518 * extension opcode based on which type of operation it is. 519 */ 520 if (enable) { 521 reg |= CQSPI_REG_CONFIG_DTR_PROTO; 522 reg |= CQSPI_REG_CONFIG_DUAL_OPCODE; 523 524 /* Set up command opcode extension. */ 525 ret = cqspi_setup_opcode_ext(f_pdata, op, shift); 526 if (ret) 527 return ret; 528 } else { 529 reg &= ~CQSPI_REG_CONFIG_DTR_PROTO; 530 reg &= ~CQSPI_REG_CONFIG_DUAL_OPCODE; 531 } 532 533 writel(reg, reg_base + CQSPI_REG_CONFIG); 534 535 return cqspi_wait_idle(cqspi); 536 } 537 538 static int cqspi_command_read(struct cqspi_flash_pdata *f_pdata, 539 const struct spi_mem_op *op) 540 { 541 struct cqspi_st *cqspi = f_pdata->cqspi; 542 void __iomem *reg_base = cqspi->iobase; 543 u8 *rxbuf = op->data.buf.in; 544 u8 opcode; 545 size_t n_rx = op->data.nbytes; 546 unsigned int rdreg; 547 unsigned int reg; 548 unsigned int dummy_clk; 549 size_t read_len; 550 int status; 551 552 status = cqspi_set_protocol(f_pdata, op); 553 if (status) 554 return status; 555 556 status = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_STIG_LSB, 557 f_pdata->dtr); 558 if (status) 559 return status; 560 561 if (!n_rx || n_rx > CQSPI_STIG_DATA_LEN_MAX || !rxbuf) { 562 dev_err(&cqspi->pdev->dev, 563 "Invalid input argument, len %zu rxbuf 0x%p\n", 564 n_rx, rxbuf); 565 return -EINVAL; 566 } 567 568 if (f_pdata->dtr) 569 opcode = op->cmd.opcode >> 8; 570 else 571 opcode = op->cmd.opcode; 572 573 reg = opcode << CQSPI_REG_CMDCTRL_OPCODE_LSB; 574 575 rdreg = cqspi_calc_rdreg(f_pdata); 576 writel(rdreg, reg_base + CQSPI_REG_RD_INSTR); 577 578 dummy_clk = cqspi_calc_dummy(op, f_pdata->dtr); 579 if (dummy_clk > CQSPI_DUMMY_CLKS_MAX) 580 return -EOPNOTSUPP; 581 582 if (dummy_clk) 583 reg |= (dummy_clk & CQSPI_REG_CMDCTRL_DUMMY_MASK) 584 << CQSPI_REG_CMDCTRL_DUMMY_LSB; 585 586 reg |= (0x1 << CQSPI_REG_CMDCTRL_RD_EN_LSB); 587 588 /* 0 means 1 byte. */ 589 reg |= (((n_rx - 1) & CQSPI_REG_CMDCTRL_RD_BYTES_MASK) 590 << CQSPI_REG_CMDCTRL_RD_BYTES_LSB); 591 status = cqspi_exec_flash_cmd(cqspi, reg); 592 if (status) 593 return status; 594 595 reg = readl(reg_base + CQSPI_REG_CMDREADDATALOWER); 596 597 /* Put the read value into rx_buf */ 598 read_len = (n_rx > 4) ? 4 : n_rx; 599 memcpy(rxbuf, ®, read_len); 600 rxbuf += read_len; 601 602 if (n_rx > 4) { 603 reg = readl(reg_base + CQSPI_REG_CMDREADDATAUPPER); 604 605 read_len = n_rx - read_len; 606 memcpy(rxbuf, ®, read_len); 607 } 608 609 return 0; 610 } 611 612 static int cqspi_command_write(struct cqspi_flash_pdata *f_pdata, 613 const struct spi_mem_op *op) 614 { 615 struct cqspi_st *cqspi = f_pdata->cqspi; 616 void __iomem *reg_base = cqspi->iobase; 617 u8 opcode; 618 const u8 *txbuf = op->data.buf.out; 619 size_t n_tx = op->data.nbytes; 620 unsigned int reg; 621 unsigned int data; 622 size_t write_len; 623 int ret; 624 625 ret = cqspi_set_protocol(f_pdata, op); 626 if (ret) 627 return ret; 628 629 ret = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_STIG_LSB, 630 f_pdata->dtr); 631 if (ret) 632 return ret; 633 634 if (n_tx > CQSPI_STIG_DATA_LEN_MAX || (n_tx && !txbuf)) { 635 dev_err(&cqspi->pdev->dev, 636 "Invalid input argument, cmdlen %zu txbuf 0x%p\n", 637 n_tx, txbuf); 638 return -EINVAL; 639 } 640 641 reg = cqspi_calc_rdreg(f_pdata); 642 writel(reg, reg_base + CQSPI_REG_RD_INSTR); 643 644 if (f_pdata->dtr) 645 opcode = op->cmd.opcode >> 8; 646 else 647 opcode = op->cmd.opcode; 648 649 reg = opcode << CQSPI_REG_CMDCTRL_OPCODE_LSB; 650 651 if (op->addr.nbytes) { 652 reg |= (0x1 << CQSPI_REG_CMDCTRL_ADDR_EN_LSB); 653 reg |= ((op->addr.nbytes - 1) & 654 CQSPI_REG_CMDCTRL_ADD_BYTES_MASK) 655 << CQSPI_REG_CMDCTRL_ADD_BYTES_LSB; 656 657 writel(op->addr.val, reg_base + CQSPI_REG_CMDADDRESS); 658 } 659 660 if (n_tx) { 661 reg |= (0x1 << CQSPI_REG_CMDCTRL_WR_EN_LSB); 662 reg |= ((n_tx - 1) & CQSPI_REG_CMDCTRL_WR_BYTES_MASK) 663 << CQSPI_REG_CMDCTRL_WR_BYTES_LSB; 664 data = 0; 665 write_len = (n_tx > 4) ? 4 : n_tx; 666 memcpy(&data, txbuf, write_len); 667 txbuf += write_len; 668 writel(data, reg_base + CQSPI_REG_CMDWRITEDATALOWER); 669 670 if (n_tx > 4) { 671 data = 0; 672 write_len = n_tx - 4; 673 memcpy(&data, txbuf, write_len); 674 writel(data, reg_base + CQSPI_REG_CMDWRITEDATAUPPER); 675 } 676 } 677 678 return cqspi_exec_flash_cmd(cqspi, reg); 679 } 680 681 static int cqspi_read_setup(struct cqspi_flash_pdata *f_pdata, 682 const struct spi_mem_op *op) 683 { 684 struct cqspi_st *cqspi = f_pdata->cqspi; 685 void __iomem *reg_base = cqspi->iobase; 686 unsigned int dummy_clk = 0; 687 unsigned int reg; 688 int ret; 689 u8 opcode; 690 691 ret = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_READ_LSB, 692 f_pdata->dtr); 693 if (ret) 694 return ret; 695 696 if (f_pdata->dtr) 697 opcode = op->cmd.opcode >> 8; 698 else 699 opcode = op->cmd.opcode; 700 701 reg = opcode << CQSPI_REG_RD_INSTR_OPCODE_LSB; 702 reg |= cqspi_calc_rdreg(f_pdata); 703 704 /* Setup dummy clock cycles */ 705 dummy_clk = cqspi_calc_dummy(op, f_pdata->dtr); 706 707 if (dummy_clk > CQSPI_DUMMY_CLKS_MAX) 708 return -EOPNOTSUPP; 709 710 if (dummy_clk) 711 reg |= (dummy_clk & CQSPI_REG_RD_INSTR_DUMMY_MASK) 712 << CQSPI_REG_RD_INSTR_DUMMY_LSB; 713 714 writel(reg, reg_base + CQSPI_REG_RD_INSTR); 715 716 /* Set address width */ 717 reg = readl(reg_base + CQSPI_REG_SIZE); 718 reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK; 719 reg |= (op->addr.nbytes - 1); 720 writel(reg, reg_base + CQSPI_REG_SIZE); 721 return 0; 722 } 723 724 static int cqspi_indirect_read_execute(struct cqspi_flash_pdata *f_pdata, 725 u8 *rxbuf, loff_t from_addr, 726 const size_t n_rx) 727 { 728 struct cqspi_st *cqspi = f_pdata->cqspi; 729 struct device *dev = &cqspi->pdev->dev; 730 void __iomem *reg_base = cqspi->iobase; 731 void __iomem *ahb_base = cqspi->ahb_base; 732 unsigned int remaining = n_rx; 733 unsigned int mod_bytes = n_rx % 4; 734 unsigned int bytes_to_read = 0; 735 u8 *rxbuf_end = rxbuf + n_rx; 736 int ret = 0; 737 738 writel(from_addr, reg_base + CQSPI_REG_INDIRECTRDSTARTADDR); 739 writel(remaining, reg_base + CQSPI_REG_INDIRECTRDBYTES); 740 741 /* Clear all interrupts. */ 742 writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS); 743 744 writel(CQSPI_IRQ_MASK_RD, reg_base + CQSPI_REG_IRQMASK); 745 746 reinit_completion(&cqspi->transfer_complete); 747 writel(CQSPI_REG_INDIRECTRD_START_MASK, 748 reg_base + CQSPI_REG_INDIRECTRD); 749 750 while (remaining > 0) { 751 if (!wait_for_completion_timeout(&cqspi->transfer_complete, 752 msecs_to_jiffies(CQSPI_READ_TIMEOUT_MS))) 753 ret = -ETIMEDOUT; 754 755 bytes_to_read = cqspi_get_rd_sram_level(cqspi); 756 757 if (ret && bytes_to_read == 0) { 758 dev_err(dev, "Indirect read timeout, no bytes\n"); 759 goto failrd; 760 } 761 762 while (bytes_to_read != 0) { 763 unsigned int word_remain = round_down(remaining, 4); 764 765 bytes_to_read *= cqspi->fifo_width; 766 bytes_to_read = bytes_to_read > remaining ? 767 remaining : bytes_to_read; 768 bytes_to_read = round_down(bytes_to_read, 4); 769 /* Read 4 byte word chunks then single bytes */ 770 if (bytes_to_read) { 771 ioread32_rep(ahb_base, rxbuf, 772 (bytes_to_read / 4)); 773 } else if (!word_remain && mod_bytes) { 774 unsigned int temp = ioread32(ahb_base); 775 776 bytes_to_read = mod_bytes; 777 memcpy(rxbuf, &temp, min((unsigned int) 778 (rxbuf_end - rxbuf), 779 bytes_to_read)); 780 } 781 rxbuf += bytes_to_read; 782 remaining -= bytes_to_read; 783 bytes_to_read = cqspi_get_rd_sram_level(cqspi); 784 } 785 786 if (remaining > 0) 787 reinit_completion(&cqspi->transfer_complete); 788 } 789 790 /* Check indirect done status */ 791 ret = cqspi_wait_for_bit(reg_base + CQSPI_REG_INDIRECTRD, 792 CQSPI_REG_INDIRECTRD_DONE_MASK, 0); 793 if (ret) { 794 dev_err(dev, "Indirect read completion error (%i)\n", ret); 795 goto failrd; 796 } 797 798 /* Disable interrupt */ 799 writel(0, reg_base + CQSPI_REG_IRQMASK); 800 801 /* Clear indirect completion status */ 802 writel(CQSPI_REG_INDIRECTRD_DONE_MASK, reg_base + CQSPI_REG_INDIRECTRD); 803 804 return 0; 805 806 failrd: 807 /* Disable interrupt */ 808 writel(0, reg_base + CQSPI_REG_IRQMASK); 809 810 /* Cancel the indirect read */ 811 writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK, 812 reg_base + CQSPI_REG_INDIRECTRD); 813 return ret; 814 } 815 816 static int cqspi_versal_indirect_read_dma(struct cqspi_flash_pdata *f_pdata, 817 u_char *rxbuf, loff_t from_addr, 818 size_t n_rx) 819 { 820 struct cqspi_st *cqspi = f_pdata->cqspi; 821 struct device *dev = &cqspi->pdev->dev; 822 void __iomem *reg_base = cqspi->iobase; 823 u32 reg, bytes_to_dma; 824 loff_t addr = from_addr; 825 void *buf = rxbuf; 826 dma_addr_t dma_addr; 827 u8 bytes_rem; 828 int ret = 0; 829 830 bytes_rem = n_rx % 4; 831 bytes_to_dma = (n_rx - bytes_rem); 832 833 if (!bytes_to_dma) 834 goto nondmard; 835 836 ret = zynqmp_pm_ospi_mux_select(cqspi->pd_dev_id, PM_OSPI_MUX_SEL_DMA); 837 if (ret) 838 return ret; 839 840 reg = readl(cqspi->iobase + CQSPI_REG_CONFIG); 841 reg |= CQSPI_REG_CONFIG_DMA_MASK; 842 writel(reg, cqspi->iobase + CQSPI_REG_CONFIG); 843 844 dma_addr = dma_map_single(dev, rxbuf, bytes_to_dma, DMA_FROM_DEVICE); 845 if (dma_mapping_error(dev, dma_addr)) { 846 dev_err(dev, "dma mapping failed\n"); 847 return -ENOMEM; 848 } 849 850 writel(from_addr, reg_base + CQSPI_REG_INDIRECTRDSTARTADDR); 851 writel(bytes_to_dma, reg_base + CQSPI_REG_INDIRECTRDBYTES); 852 writel(CQSPI_REG_VERSAL_ADDRRANGE_WIDTH_VAL, 853 reg_base + CQSPI_REG_INDTRIG_ADDRRANGE); 854 855 /* Clear all interrupts. */ 856 writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS); 857 858 /* Enable DMA done interrupt */ 859 writel(CQSPI_REG_VERSAL_DMA_DST_DONE_MASK, 860 reg_base + CQSPI_REG_VERSAL_DMA_DST_I_EN); 861 862 /* Default DMA periph configuration */ 863 writel(CQSPI_REG_VERSAL_DMA_VAL, reg_base + CQSPI_REG_DMA); 864 865 /* Configure DMA Dst address */ 866 writel(lower_32_bits(dma_addr), 867 reg_base + CQSPI_REG_VERSAL_DMA_DST_ADDR); 868 writel(upper_32_bits(dma_addr), 869 reg_base + CQSPI_REG_VERSAL_DMA_DST_ADDR_MSB); 870 871 /* Configure DMA Src address */ 872 writel(cqspi->trigger_address, reg_base + 873 CQSPI_REG_VERSAL_DMA_SRC_ADDR); 874 875 /* Set DMA destination size */ 876 writel(bytes_to_dma, reg_base + CQSPI_REG_VERSAL_DMA_DST_SIZE); 877 878 /* Set DMA destination control */ 879 writel(CQSPI_REG_VERSAL_DMA_DST_CTRL_VAL, 880 reg_base + CQSPI_REG_VERSAL_DMA_DST_CTRL); 881 882 writel(CQSPI_REG_INDIRECTRD_START_MASK, 883 reg_base + CQSPI_REG_INDIRECTRD); 884 885 reinit_completion(&cqspi->transfer_complete); 886 887 if (!wait_for_completion_timeout(&cqspi->transfer_complete, 888 msecs_to_jiffies(CQSPI_READ_TIMEOUT_MS))) { 889 ret = -ETIMEDOUT; 890 goto failrd; 891 } 892 893 /* Disable DMA interrupt */ 894 writel(0x0, cqspi->iobase + CQSPI_REG_VERSAL_DMA_DST_I_DIS); 895 896 /* Clear indirect completion status */ 897 writel(CQSPI_REG_INDIRECTRD_DONE_MASK, 898 cqspi->iobase + CQSPI_REG_INDIRECTRD); 899 dma_unmap_single(dev, dma_addr, bytes_to_dma, DMA_FROM_DEVICE); 900 901 reg = readl(cqspi->iobase + CQSPI_REG_CONFIG); 902 reg &= ~CQSPI_REG_CONFIG_DMA_MASK; 903 writel(reg, cqspi->iobase + CQSPI_REG_CONFIG); 904 905 ret = zynqmp_pm_ospi_mux_select(cqspi->pd_dev_id, 906 PM_OSPI_MUX_SEL_LINEAR); 907 if (ret) 908 return ret; 909 910 nondmard: 911 if (bytes_rem) { 912 addr += bytes_to_dma; 913 buf += bytes_to_dma; 914 ret = cqspi_indirect_read_execute(f_pdata, buf, addr, 915 bytes_rem); 916 if (ret) 917 return ret; 918 } 919 920 return 0; 921 922 failrd: 923 /* Disable DMA interrupt */ 924 writel(0x0, reg_base + CQSPI_REG_VERSAL_DMA_DST_I_DIS); 925 926 /* Cancel the indirect read */ 927 writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK, 928 reg_base + CQSPI_REG_INDIRECTRD); 929 930 dma_unmap_single(dev, dma_addr, bytes_to_dma, DMA_FROM_DEVICE); 931 932 reg = readl(cqspi->iobase + CQSPI_REG_CONFIG); 933 reg &= ~CQSPI_REG_CONFIG_DMA_MASK; 934 writel(reg, cqspi->iobase + CQSPI_REG_CONFIG); 935 936 zynqmp_pm_ospi_mux_select(cqspi->pd_dev_id, PM_OSPI_MUX_SEL_LINEAR); 937 938 return ret; 939 } 940 941 static int cqspi_write_setup(struct cqspi_flash_pdata *f_pdata, 942 const struct spi_mem_op *op) 943 { 944 unsigned int reg; 945 int ret; 946 struct cqspi_st *cqspi = f_pdata->cqspi; 947 void __iomem *reg_base = cqspi->iobase; 948 u8 opcode; 949 950 ret = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_WRITE_LSB, 951 f_pdata->dtr); 952 if (ret) 953 return ret; 954 955 if (f_pdata->dtr) 956 opcode = op->cmd.opcode >> 8; 957 else 958 opcode = op->cmd.opcode; 959 960 /* Set opcode. */ 961 reg = opcode << CQSPI_REG_WR_INSTR_OPCODE_LSB; 962 reg |= f_pdata->data_width << CQSPI_REG_WR_INSTR_TYPE_DATA_LSB; 963 reg |= f_pdata->addr_width << CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB; 964 writel(reg, reg_base + CQSPI_REG_WR_INSTR); 965 reg = cqspi_calc_rdreg(f_pdata); 966 writel(reg, reg_base + CQSPI_REG_RD_INSTR); 967 968 /* 969 * SPI NAND flashes require the address of the status register to be 970 * passed in the Read SR command. Also, some SPI NOR flashes like the 971 * cypress Semper flash expect a 4-byte dummy address in the Read SR 972 * command in DTR mode. 973 * 974 * But this controller does not support address phase in the Read SR 975 * command when doing auto-HW polling. So, disable write completion 976 * polling on the controller's side. spinand and spi-nor will take 977 * care of polling the status register. 978 */ 979 if (cqspi->wr_completion) { 980 reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL); 981 reg |= CQSPI_REG_WR_DISABLE_AUTO_POLL; 982 writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL); 983 } 984 985 reg = readl(reg_base + CQSPI_REG_SIZE); 986 reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK; 987 reg |= (op->addr.nbytes - 1); 988 writel(reg, reg_base + CQSPI_REG_SIZE); 989 return 0; 990 } 991 992 static int cqspi_indirect_write_execute(struct cqspi_flash_pdata *f_pdata, 993 loff_t to_addr, const u8 *txbuf, 994 const size_t n_tx) 995 { 996 struct cqspi_st *cqspi = f_pdata->cqspi; 997 struct device *dev = &cqspi->pdev->dev; 998 void __iomem *reg_base = cqspi->iobase; 999 unsigned int remaining = n_tx; 1000 unsigned int write_bytes; 1001 int ret; 1002 1003 writel(to_addr, reg_base + CQSPI_REG_INDIRECTWRSTARTADDR); 1004 writel(remaining, reg_base + CQSPI_REG_INDIRECTWRBYTES); 1005 1006 /* Clear all interrupts. */ 1007 writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS); 1008 1009 writel(CQSPI_IRQ_MASK_WR, reg_base + CQSPI_REG_IRQMASK); 1010 1011 reinit_completion(&cqspi->transfer_complete); 1012 writel(CQSPI_REG_INDIRECTWR_START_MASK, 1013 reg_base + CQSPI_REG_INDIRECTWR); 1014 /* 1015 * As per 66AK2G02 TRM SPRUHY8F section 11.15.5.3 Indirect Access 1016 * Controller programming sequence, couple of cycles of 1017 * QSPI_REF_CLK delay is required for the above bit to 1018 * be internally synchronized by the QSPI module. Provide 5 1019 * cycles of delay. 1020 */ 1021 if (cqspi->wr_delay) 1022 ndelay(cqspi->wr_delay); 1023 1024 while (remaining > 0) { 1025 size_t write_words, mod_bytes; 1026 1027 write_bytes = remaining; 1028 write_words = write_bytes / 4; 1029 mod_bytes = write_bytes % 4; 1030 /* Write 4 bytes at a time then single bytes. */ 1031 if (write_words) { 1032 iowrite32_rep(cqspi->ahb_base, txbuf, write_words); 1033 txbuf += (write_words * 4); 1034 } 1035 if (mod_bytes) { 1036 unsigned int temp = 0xFFFFFFFF; 1037 1038 memcpy(&temp, txbuf, mod_bytes); 1039 iowrite32(temp, cqspi->ahb_base); 1040 txbuf += mod_bytes; 1041 } 1042 1043 if (!wait_for_completion_timeout(&cqspi->transfer_complete, 1044 msecs_to_jiffies(CQSPI_TIMEOUT_MS))) { 1045 dev_err(dev, "Indirect write timeout\n"); 1046 ret = -ETIMEDOUT; 1047 goto failwr; 1048 } 1049 1050 remaining -= write_bytes; 1051 1052 if (remaining > 0) 1053 reinit_completion(&cqspi->transfer_complete); 1054 } 1055 1056 /* Check indirect done status */ 1057 ret = cqspi_wait_for_bit(reg_base + CQSPI_REG_INDIRECTWR, 1058 CQSPI_REG_INDIRECTWR_DONE_MASK, 0); 1059 if (ret) { 1060 dev_err(dev, "Indirect write completion error (%i)\n", ret); 1061 goto failwr; 1062 } 1063 1064 /* Disable interrupt. */ 1065 writel(0, reg_base + CQSPI_REG_IRQMASK); 1066 1067 /* Clear indirect completion status */ 1068 writel(CQSPI_REG_INDIRECTWR_DONE_MASK, reg_base + CQSPI_REG_INDIRECTWR); 1069 1070 cqspi_wait_idle(cqspi); 1071 1072 return 0; 1073 1074 failwr: 1075 /* Disable interrupt. */ 1076 writel(0, reg_base + CQSPI_REG_IRQMASK); 1077 1078 /* Cancel the indirect write */ 1079 writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK, 1080 reg_base + CQSPI_REG_INDIRECTWR); 1081 return ret; 1082 } 1083 1084 static void cqspi_chipselect(struct cqspi_flash_pdata *f_pdata) 1085 { 1086 struct cqspi_st *cqspi = f_pdata->cqspi; 1087 void __iomem *reg_base = cqspi->iobase; 1088 unsigned int chip_select = f_pdata->cs; 1089 unsigned int reg; 1090 1091 reg = readl(reg_base + CQSPI_REG_CONFIG); 1092 if (cqspi->is_decoded_cs) { 1093 reg |= CQSPI_REG_CONFIG_DECODE_MASK; 1094 } else { 1095 reg &= ~CQSPI_REG_CONFIG_DECODE_MASK; 1096 1097 /* Convert CS if without decoder. 1098 * CS0 to 4b'1110 1099 * CS1 to 4b'1101 1100 * CS2 to 4b'1011 1101 * CS3 to 4b'0111 1102 */ 1103 chip_select = 0xF & ~(1 << chip_select); 1104 } 1105 1106 reg &= ~(CQSPI_REG_CONFIG_CHIPSELECT_MASK 1107 << CQSPI_REG_CONFIG_CHIPSELECT_LSB); 1108 reg |= (chip_select & CQSPI_REG_CONFIG_CHIPSELECT_MASK) 1109 << CQSPI_REG_CONFIG_CHIPSELECT_LSB; 1110 writel(reg, reg_base + CQSPI_REG_CONFIG); 1111 } 1112 1113 static unsigned int calculate_ticks_for_ns(const unsigned int ref_clk_hz, 1114 const unsigned int ns_val) 1115 { 1116 unsigned int ticks; 1117 1118 ticks = ref_clk_hz / 1000; /* kHz */ 1119 ticks = DIV_ROUND_UP(ticks * ns_val, 1000000); 1120 1121 return ticks; 1122 } 1123 1124 static void cqspi_delay(struct cqspi_flash_pdata *f_pdata) 1125 { 1126 struct cqspi_st *cqspi = f_pdata->cqspi; 1127 void __iomem *iobase = cqspi->iobase; 1128 const unsigned int ref_clk_hz = cqspi->master_ref_clk_hz; 1129 unsigned int tshsl, tchsh, tslch, tsd2d; 1130 unsigned int reg; 1131 unsigned int tsclk; 1132 1133 /* calculate the number of ref ticks for one sclk tick */ 1134 tsclk = DIV_ROUND_UP(ref_clk_hz, cqspi->sclk); 1135 1136 tshsl = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tshsl_ns); 1137 /* this particular value must be at least one sclk */ 1138 if (tshsl < tsclk) 1139 tshsl = tsclk; 1140 1141 tchsh = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tchsh_ns); 1142 tslch = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tslch_ns); 1143 tsd2d = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tsd2d_ns); 1144 1145 reg = (tshsl & CQSPI_REG_DELAY_TSHSL_MASK) 1146 << CQSPI_REG_DELAY_TSHSL_LSB; 1147 reg |= (tchsh & CQSPI_REG_DELAY_TCHSH_MASK) 1148 << CQSPI_REG_DELAY_TCHSH_LSB; 1149 reg |= (tslch & CQSPI_REG_DELAY_TSLCH_MASK) 1150 << CQSPI_REG_DELAY_TSLCH_LSB; 1151 reg |= (tsd2d & CQSPI_REG_DELAY_TSD2D_MASK) 1152 << CQSPI_REG_DELAY_TSD2D_LSB; 1153 writel(reg, iobase + CQSPI_REG_DELAY); 1154 } 1155 1156 static void cqspi_config_baudrate_div(struct cqspi_st *cqspi) 1157 { 1158 const unsigned int ref_clk_hz = cqspi->master_ref_clk_hz; 1159 void __iomem *reg_base = cqspi->iobase; 1160 u32 reg, div; 1161 1162 /* Recalculate the baudrate divisor based on QSPI specification. */ 1163 div = DIV_ROUND_UP(ref_clk_hz, 2 * cqspi->sclk) - 1; 1164 1165 reg = readl(reg_base + CQSPI_REG_CONFIG); 1166 reg &= ~(CQSPI_REG_CONFIG_BAUD_MASK << CQSPI_REG_CONFIG_BAUD_LSB); 1167 reg |= (div & CQSPI_REG_CONFIG_BAUD_MASK) << CQSPI_REG_CONFIG_BAUD_LSB; 1168 writel(reg, reg_base + CQSPI_REG_CONFIG); 1169 } 1170 1171 static void cqspi_readdata_capture(struct cqspi_st *cqspi, 1172 const bool bypass, 1173 const unsigned int delay) 1174 { 1175 void __iomem *reg_base = cqspi->iobase; 1176 unsigned int reg; 1177 1178 reg = readl(reg_base + CQSPI_REG_READCAPTURE); 1179 1180 if (bypass) 1181 reg |= (1 << CQSPI_REG_READCAPTURE_BYPASS_LSB); 1182 else 1183 reg &= ~(1 << CQSPI_REG_READCAPTURE_BYPASS_LSB); 1184 1185 reg &= ~(CQSPI_REG_READCAPTURE_DELAY_MASK 1186 << CQSPI_REG_READCAPTURE_DELAY_LSB); 1187 1188 reg |= (delay & CQSPI_REG_READCAPTURE_DELAY_MASK) 1189 << CQSPI_REG_READCAPTURE_DELAY_LSB; 1190 1191 writel(reg, reg_base + CQSPI_REG_READCAPTURE); 1192 } 1193 1194 static void cqspi_controller_enable(struct cqspi_st *cqspi, bool enable) 1195 { 1196 void __iomem *reg_base = cqspi->iobase; 1197 unsigned int reg; 1198 1199 reg = readl(reg_base + CQSPI_REG_CONFIG); 1200 1201 if (enable) 1202 reg |= CQSPI_REG_CONFIG_ENABLE_MASK; 1203 else 1204 reg &= ~CQSPI_REG_CONFIG_ENABLE_MASK; 1205 1206 writel(reg, reg_base + CQSPI_REG_CONFIG); 1207 } 1208 1209 static void cqspi_configure(struct cqspi_flash_pdata *f_pdata, 1210 unsigned long sclk) 1211 { 1212 struct cqspi_st *cqspi = f_pdata->cqspi; 1213 int switch_cs = (cqspi->current_cs != f_pdata->cs); 1214 int switch_ck = (cqspi->sclk != sclk); 1215 1216 if (switch_cs || switch_ck) 1217 cqspi_controller_enable(cqspi, 0); 1218 1219 /* Switch chip select. */ 1220 if (switch_cs) { 1221 cqspi->current_cs = f_pdata->cs; 1222 cqspi_chipselect(f_pdata); 1223 } 1224 1225 /* Setup baudrate divisor and delays */ 1226 if (switch_ck) { 1227 cqspi->sclk = sclk; 1228 cqspi_config_baudrate_div(cqspi); 1229 cqspi_delay(f_pdata); 1230 cqspi_readdata_capture(cqspi, !cqspi->rclk_en, 1231 f_pdata->read_delay); 1232 } 1233 1234 if (switch_cs || switch_ck) 1235 cqspi_controller_enable(cqspi, 1); 1236 } 1237 1238 static ssize_t cqspi_write(struct cqspi_flash_pdata *f_pdata, 1239 const struct spi_mem_op *op) 1240 { 1241 struct cqspi_st *cqspi = f_pdata->cqspi; 1242 loff_t to = op->addr.val; 1243 size_t len = op->data.nbytes; 1244 const u_char *buf = op->data.buf.out; 1245 int ret; 1246 1247 ret = cqspi_set_protocol(f_pdata, op); 1248 if (ret) 1249 return ret; 1250 1251 ret = cqspi_write_setup(f_pdata, op); 1252 if (ret) 1253 return ret; 1254 1255 /* 1256 * Some flashes like the Cypress Semper flash expect a dummy 4-byte 1257 * address (all 0s) with the read status register command in DTR mode. 1258 * But this controller does not support sending dummy address bytes to 1259 * the flash when it is polling the write completion register in DTR 1260 * mode. So, we can not use direct mode when in DTR mode for writing 1261 * data. 1262 */ 1263 if (!f_pdata->dtr && cqspi->use_direct_mode && 1264 ((to + len) <= cqspi->ahb_size)) { 1265 memcpy_toio(cqspi->ahb_base + to, buf, len); 1266 return cqspi_wait_idle(cqspi); 1267 } 1268 1269 return cqspi_indirect_write_execute(f_pdata, to, buf, len); 1270 } 1271 1272 static void cqspi_rx_dma_callback(void *param) 1273 { 1274 struct cqspi_st *cqspi = param; 1275 1276 complete(&cqspi->rx_dma_complete); 1277 } 1278 1279 static int cqspi_direct_read_execute(struct cqspi_flash_pdata *f_pdata, 1280 u_char *buf, loff_t from, size_t len) 1281 { 1282 struct cqspi_st *cqspi = f_pdata->cqspi; 1283 struct device *dev = &cqspi->pdev->dev; 1284 enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT; 1285 dma_addr_t dma_src = (dma_addr_t)cqspi->mmap_phys_base + from; 1286 int ret = 0; 1287 struct dma_async_tx_descriptor *tx; 1288 dma_cookie_t cookie; 1289 dma_addr_t dma_dst; 1290 struct device *ddev; 1291 1292 if (!cqspi->rx_chan || !virt_addr_valid(buf)) { 1293 memcpy_fromio(buf, cqspi->ahb_base + from, len); 1294 return 0; 1295 } 1296 1297 ddev = cqspi->rx_chan->device->dev; 1298 dma_dst = dma_map_single(ddev, buf, len, DMA_FROM_DEVICE); 1299 if (dma_mapping_error(ddev, dma_dst)) { 1300 dev_err(dev, "dma mapping failed\n"); 1301 return -ENOMEM; 1302 } 1303 tx = dmaengine_prep_dma_memcpy(cqspi->rx_chan, dma_dst, dma_src, 1304 len, flags); 1305 if (!tx) { 1306 dev_err(dev, "device_prep_dma_memcpy error\n"); 1307 ret = -EIO; 1308 goto err_unmap; 1309 } 1310 1311 tx->callback = cqspi_rx_dma_callback; 1312 tx->callback_param = cqspi; 1313 cookie = tx->tx_submit(tx); 1314 reinit_completion(&cqspi->rx_dma_complete); 1315 1316 ret = dma_submit_error(cookie); 1317 if (ret) { 1318 dev_err(dev, "dma_submit_error %d\n", cookie); 1319 ret = -EIO; 1320 goto err_unmap; 1321 } 1322 1323 dma_async_issue_pending(cqspi->rx_chan); 1324 if (!wait_for_completion_timeout(&cqspi->rx_dma_complete, 1325 msecs_to_jiffies(max_t(size_t, len, 500)))) { 1326 dmaengine_terminate_sync(cqspi->rx_chan); 1327 dev_err(dev, "DMA wait_for_completion_timeout\n"); 1328 ret = -ETIMEDOUT; 1329 goto err_unmap; 1330 } 1331 1332 err_unmap: 1333 dma_unmap_single(ddev, dma_dst, len, DMA_FROM_DEVICE); 1334 1335 return ret; 1336 } 1337 1338 static ssize_t cqspi_read(struct cqspi_flash_pdata *f_pdata, 1339 const struct spi_mem_op *op) 1340 { 1341 struct cqspi_st *cqspi = f_pdata->cqspi; 1342 struct device *dev = &cqspi->pdev->dev; 1343 const struct cqspi_driver_platdata *ddata; 1344 loff_t from = op->addr.val; 1345 size_t len = op->data.nbytes; 1346 u_char *buf = op->data.buf.in; 1347 u64 dma_align = (u64)(uintptr_t)buf; 1348 int ret; 1349 1350 ddata = of_device_get_match_data(dev); 1351 ret = cqspi_set_protocol(f_pdata, op); 1352 if (ret) 1353 return ret; 1354 1355 ret = cqspi_read_setup(f_pdata, op); 1356 if (ret) 1357 return ret; 1358 1359 if (cqspi->use_direct_mode && ((from + len) <= cqspi->ahb_size)) 1360 return cqspi_direct_read_execute(f_pdata, buf, from, len); 1361 1362 if (cqspi->use_dma_read && ddata && ddata->indirect_read_dma && 1363 virt_addr_valid(buf) && ((dma_align & CQSPI_DMA_UNALIGN) == 0)) 1364 return ddata->indirect_read_dma(f_pdata, buf, from, len); 1365 1366 return cqspi_indirect_read_execute(f_pdata, buf, from, len); 1367 } 1368 1369 static int cqspi_mem_process(struct spi_mem *mem, const struct spi_mem_op *op) 1370 { 1371 struct cqspi_st *cqspi = spi_master_get_devdata(mem->spi->master); 1372 struct cqspi_flash_pdata *f_pdata; 1373 1374 f_pdata = &cqspi->f_pdata[mem->spi->chip_select]; 1375 cqspi_configure(f_pdata, mem->spi->max_speed_hz); 1376 1377 if (op->data.dir == SPI_MEM_DATA_IN && op->data.buf.in) { 1378 if (!op->addr.nbytes) 1379 return cqspi_command_read(f_pdata, op); 1380 1381 return cqspi_read(f_pdata, op); 1382 } 1383 1384 if (!op->addr.nbytes || !op->data.buf.out) 1385 return cqspi_command_write(f_pdata, op); 1386 1387 return cqspi_write(f_pdata, op); 1388 } 1389 1390 static int cqspi_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op) 1391 { 1392 int ret; 1393 1394 ret = cqspi_mem_process(mem, op); 1395 if (ret) 1396 dev_err(&mem->spi->dev, "operation failed with %d\n", ret); 1397 1398 return ret; 1399 } 1400 1401 static bool cqspi_supports_mem_op(struct spi_mem *mem, 1402 const struct spi_mem_op *op) 1403 { 1404 bool all_true, all_false; 1405 1406 /* 1407 * op->dummy.dtr is required for converting nbytes into ncycles. 1408 * Also, don't check the dtr field of the op phase having zero nbytes. 1409 */ 1410 all_true = op->cmd.dtr && 1411 (!op->addr.nbytes || op->addr.dtr) && 1412 (!op->dummy.nbytes || op->dummy.dtr) && 1413 (!op->data.nbytes || op->data.dtr); 1414 1415 all_false = !op->cmd.dtr && !op->addr.dtr && !op->dummy.dtr && 1416 !op->data.dtr; 1417 1418 /* Mixed DTR modes not supported. */ 1419 if (!(all_true || all_false)) 1420 return false; 1421 1422 return spi_mem_default_supports_op(mem, op); 1423 } 1424 1425 static int cqspi_of_get_flash_pdata(struct platform_device *pdev, 1426 struct cqspi_flash_pdata *f_pdata, 1427 struct device_node *np) 1428 { 1429 if (of_property_read_u32(np, "cdns,read-delay", &f_pdata->read_delay)) { 1430 dev_err(&pdev->dev, "couldn't determine read-delay\n"); 1431 return -ENXIO; 1432 } 1433 1434 if (of_property_read_u32(np, "cdns,tshsl-ns", &f_pdata->tshsl_ns)) { 1435 dev_err(&pdev->dev, "couldn't determine tshsl-ns\n"); 1436 return -ENXIO; 1437 } 1438 1439 if (of_property_read_u32(np, "cdns,tsd2d-ns", &f_pdata->tsd2d_ns)) { 1440 dev_err(&pdev->dev, "couldn't determine tsd2d-ns\n"); 1441 return -ENXIO; 1442 } 1443 1444 if (of_property_read_u32(np, "cdns,tchsh-ns", &f_pdata->tchsh_ns)) { 1445 dev_err(&pdev->dev, "couldn't determine tchsh-ns\n"); 1446 return -ENXIO; 1447 } 1448 1449 if (of_property_read_u32(np, "cdns,tslch-ns", &f_pdata->tslch_ns)) { 1450 dev_err(&pdev->dev, "couldn't determine tslch-ns\n"); 1451 return -ENXIO; 1452 } 1453 1454 if (of_property_read_u32(np, "spi-max-frequency", &f_pdata->clk_rate)) { 1455 dev_err(&pdev->dev, "couldn't determine spi-max-frequency\n"); 1456 return -ENXIO; 1457 } 1458 1459 return 0; 1460 } 1461 1462 static int cqspi_of_get_pdata(struct cqspi_st *cqspi) 1463 { 1464 struct device *dev = &cqspi->pdev->dev; 1465 struct device_node *np = dev->of_node; 1466 u32 id[2]; 1467 1468 cqspi->is_decoded_cs = of_property_read_bool(np, "cdns,is-decoded-cs"); 1469 1470 if (of_property_read_u32(np, "cdns,fifo-depth", &cqspi->fifo_depth)) { 1471 dev_err(dev, "couldn't determine fifo-depth\n"); 1472 return -ENXIO; 1473 } 1474 1475 if (of_property_read_u32(np, "cdns,fifo-width", &cqspi->fifo_width)) { 1476 dev_err(dev, "couldn't determine fifo-width\n"); 1477 return -ENXIO; 1478 } 1479 1480 if (of_property_read_u32(np, "cdns,trigger-address", 1481 &cqspi->trigger_address)) { 1482 dev_err(dev, "couldn't determine trigger-address\n"); 1483 return -ENXIO; 1484 } 1485 1486 if (of_property_read_u32(np, "num-cs", &cqspi->num_chipselect)) 1487 cqspi->num_chipselect = CQSPI_MAX_CHIPSELECT; 1488 1489 cqspi->rclk_en = of_property_read_bool(np, "cdns,rclk-en"); 1490 1491 if (!of_property_read_u32_array(np, "power-domains", id, 1492 ARRAY_SIZE(id))) 1493 cqspi->pd_dev_id = id[1]; 1494 1495 return 0; 1496 } 1497 1498 static void cqspi_controller_init(struct cqspi_st *cqspi) 1499 { 1500 u32 reg; 1501 1502 cqspi_controller_enable(cqspi, 0); 1503 1504 /* Configure the remap address register, no remap */ 1505 writel(0, cqspi->iobase + CQSPI_REG_REMAP); 1506 1507 /* Disable all interrupts. */ 1508 writel(0, cqspi->iobase + CQSPI_REG_IRQMASK); 1509 1510 /* Configure the SRAM split to 1:1 . */ 1511 writel(cqspi->fifo_depth / 2, cqspi->iobase + CQSPI_REG_SRAMPARTITION); 1512 1513 /* Load indirect trigger address. */ 1514 writel(cqspi->trigger_address, 1515 cqspi->iobase + CQSPI_REG_INDIRECTTRIGGER); 1516 1517 /* Program read watermark -- 1/2 of the FIFO. */ 1518 writel(cqspi->fifo_depth * cqspi->fifo_width / 2, 1519 cqspi->iobase + CQSPI_REG_INDIRECTRDWATERMARK); 1520 /* Program write watermark -- 1/8 of the FIFO. */ 1521 writel(cqspi->fifo_depth * cqspi->fifo_width / 8, 1522 cqspi->iobase + CQSPI_REG_INDIRECTWRWATERMARK); 1523 1524 /* Disable direct access controller */ 1525 if (!cqspi->use_direct_mode) { 1526 reg = readl(cqspi->iobase + CQSPI_REG_CONFIG); 1527 reg &= ~CQSPI_REG_CONFIG_ENB_DIR_ACC_CTRL; 1528 writel(reg, cqspi->iobase + CQSPI_REG_CONFIG); 1529 } 1530 1531 /* Enable DMA interface */ 1532 if (cqspi->use_dma_read) { 1533 reg = readl(cqspi->iobase + CQSPI_REG_CONFIG); 1534 reg |= CQSPI_REG_CONFIG_DMA_MASK; 1535 writel(reg, cqspi->iobase + CQSPI_REG_CONFIG); 1536 } 1537 1538 cqspi_controller_enable(cqspi, 1); 1539 } 1540 1541 static int cqspi_request_mmap_dma(struct cqspi_st *cqspi) 1542 { 1543 dma_cap_mask_t mask; 1544 1545 dma_cap_zero(mask); 1546 dma_cap_set(DMA_MEMCPY, mask); 1547 1548 cqspi->rx_chan = dma_request_chan_by_mask(&mask); 1549 if (IS_ERR(cqspi->rx_chan)) { 1550 int ret = PTR_ERR(cqspi->rx_chan); 1551 cqspi->rx_chan = NULL; 1552 return dev_err_probe(&cqspi->pdev->dev, ret, "No Rx DMA available\n"); 1553 } 1554 init_completion(&cqspi->rx_dma_complete); 1555 1556 return 0; 1557 } 1558 1559 static const char *cqspi_get_name(struct spi_mem *mem) 1560 { 1561 struct cqspi_st *cqspi = spi_master_get_devdata(mem->spi->master); 1562 struct device *dev = &cqspi->pdev->dev; 1563 1564 return devm_kasprintf(dev, GFP_KERNEL, "%s.%d", dev_name(dev), mem->spi->chip_select); 1565 } 1566 1567 static const struct spi_controller_mem_ops cqspi_mem_ops = { 1568 .exec_op = cqspi_exec_mem_op, 1569 .get_name = cqspi_get_name, 1570 .supports_op = cqspi_supports_mem_op, 1571 }; 1572 1573 static const struct spi_controller_mem_caps cqspi_mem_caps = { 1574 .dtr = true, 1575 }; 1576 1577 static int cqspi_setup_flash(struct cqspi_st *cqspi) 1578 { 1579 struct platform_device *pdev = cqspi->pdev; 1580 struct device *dev = &pdev->dev; 1581 struct device_node *np = dev->of_node; 1582 struct cqspi_flash_pdata *f_pdata; 1583 unsigned int cs; 1584 int ret; 1585 1586 /* Get flash device data */ 1587 for_each_available_child_of_node(dev->of_node, np) { 1588 ret = of_property_read_u32(np, "reg", &cs); 1589 if (ret) { 1590 dev_err(dev, "Couldn't determine chip select.\n"); 1591 of_node_put(np); 1592 return ret; 1593 } 1594 1595 if (cs >= CQSPI_MAX_CHIPSELECT) { 1596 dev_err(dev, "Chip select %d out of range.\n", cs); 1597 of_node_put(np); 1598 return -EINVAL; 1599 } 1600 1601 f_pdata = &cqspi->f_pdata[cs]; 1602 f_pdata->cqspi = cqspi; 1603 f_pdata->cs = cs; 1604 1605 ret = cqspi_of_get_flash_pdata(pdev, f_pdata, np); 1606 if (ret) { 1607 of_node_put(np); 1608 return ret; 1609 } 1610 } 1611 1612 return 0; 1613 } 1614 1615 static int cqspi_probe(struct platform_device *pdev) 1616 { 1617 const struct cqspi_driver_platdata *ddata; 1618 struct reset_control *rstc, *rstc_ocp; 1619 struct device *dev = &pdev->dev; 1620 struct spi_master *master; 1621 struct resource *res_ahb; 1622 struct cqspi_st *cqspi; 1623 struct resource *res; 1624 int ret; 1625 int irq; 1626 1627 master = spi_alloc_master(&pdev->dev, sizeof(*cqspi)); 1628 if (!master) { 1629 dev_err(&pdev->dev, "spi_alloc_master failed\n"); 1630 return -ENOMEM; 1631 } 1632 master->mode_bits = SPI_RX_QUAD | SPI_RX_DUAL; 1633 master->mem_ops = &cqspi_mem_ops; 1634 master->mem_caps = &cqspi_mem_caps; 1635 master->dev.of_node = pdev->dev.of_node; 1636 1637 cqspi = spi_master_get_devdata(master); 1638 1639 cqspi->pdev = pdev; 1640 platform_set_drvdata(pdev, cqspi); 1641 1642 /* Obtain configuration from OF. */ 1643 ret = cqspi_of_get_pdata(cqspi); 1644 if (ret) { 1645 dev_err(dev, "Cannot get mandatory OF data.\n"); 1646 ret = -ENODEV; 1647 goto probe_master_put; 1648 } 1649 1650 /* Obtain QSPI clock. */ 1651 cqspi->clk = devm_clk_get(dev, NULL); 1652 if (IS_ERR(cqspi->clk)) { 1653 dev_err(dev, "Cannot claim QSPI clock.\n"); 1654 ret = PTR_ERR(cqspi->clk); 1655 goto probe_master_put; 1656 } 1657 1658 /* Obtain and remap controller address. */ 1659 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 1660 cqspi->iobase = devm_ioremap_resource(dev, res); 1661 if (IS_ERR(cqspi->iobase)) { 1662 dev_err(dev, "Cannot remap controller address.\n"); 1663 ret = PTR_ERR(cqspi->iobase); 1664 goto probe_master_put; 1665 } 1666 1667 /* Obtain and remap AHB address. */ 1668 res_ahb = platform_get_resource(pdev, IORESOURCE_MEM, 1); 1669 cqspi->ahb_base = devm_ioremap_resource(dev, res_ahb); 1670 if (IS_ERR(cqspi->ahb_base)) { 1671 dev_err(dev, "Cannot remap AHB address.\n"); 1672 ret = PTR_ERR(cqspi->ahb_base); 1673 goto probe_master_put; 1674 } 1675 cqspi->mmap_phys_base = (dma_addr_t)res_ahb->start; 1676 cqspi->ahb_size = resource_size(res_ahb); 1677 1678 init_completion(&cqspi->transfer_complete); 1679 1680 /* Obtain IRQ line. */ 1681 irq = platform_get_irq(pdev, 0); 1682 if (irq < 0) { 1683 ret = -ENXIO; 1684 goto probe_master_put; 1685 } 1686 1687 pm_runtime_enable(dev); 1688 ret = pm_runtime_get_sync(dev); 1689 if (ret < 0) { 1690 pm_runtime_put_noidle(dev); 1691 goto probe_master_put; 1692 } 1693 1694 ret = clk_prepare_enable(cqspi->clk); 1695 if (ret) { 1696 dev_err(dev, "Cannot enable QSPI clock.\n"); 1697 goto probe_clk_failed; 1698 } 1699 1700 /* Obtain QSPI reset control */ 1701 rstc = devm_reset_control_get_optional_exclusive(dev, "qspi"); 1702 if (IS_ERR(rstc)) { 1703 ret = PTR_ERR(rstc); 1704 dev_err(dev, "Cannot get QSPI reset.\n"); 1705 goto probe_reset_failed; 1706 } 1707 1708 rstc_ocp = devm_reset_control_get_optional_exclusive(dev, "qspi-ocp"); 1709 if (IS_ERR(rstc_ocp)) { 1710 ret = PTR_ERR(rstc_ocp); 1711 dev_err(dev, "Cannot get QSPI OCP reset.\n"); 1712 goto probe_reset_failed; 1713 } 1714 1715 reset_control_assert(rstc); 1716 reset_control_deassert(rstc); 1717 1718 reset_control_assert(rstc_ocp); 1719 reset_control_deassert(rstc_ocp); 1720 1721 cqspi->master_ref_clk_hz = clk_get_rate(cqspi->clk); 1722 master->max_speed_hz = cqspi->master_ref_clk_hz; 1723 1724 /* write completion is supported by default */ 1725 cqspi->wr_completion = true; 1726 1727 ddata = of_device_get_match_data(dev); 1728 if (ddata) { 1729 if (ddata->quirks & CQSPI_NEEDS_WR_DELAY) 1730 cqspi->wr_delay = 50 * DIV_ROUND_UP(NSEC_PER_SEC, 1731 cqspi->master_ref_clk_hz); 1732 if (ddata->hwcaps_mask & CQSPI_SUPPORTS_OCTAL) 1733 master->mode_bits |= SPI_RX_OCTAL | SPI_TX_OCTAL; 1734 if (!(ddata->quirks & CQSPI_DISABLE_DAC_MODE)) 1735 cqspi->use_direct_mode = true; 1736 if (ddata->quirks & CQSPI_SUPPORT_EXTERNAL_DMA) 1737 cqspi->use_dma_read = true; 1738 if (ddata->quirks & CQSPI_NO_SUPPORT_WR_COMPLETION) 1739 cqspi->wr_completion = false; 1740 1741 if (of_device_is_compatible(pdev->dev.of_node, 1742 "xlnx,versal-ospi-1.0")) 1743 dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)); 1744 } 1745 1746 ret = devm_request_irq(dev, irq, cqspi_irq_handler, 0, 1747 pdev->name, cqspi); 1748 if (ret) { 1749 dev_err(dev, "Cannot request IRQ.\n"); 1750 goto probe_reset_failed; 1751 } 1752 1753 cqspi_wait_idle(cqspi); 1754 cqspi_controller_init(cqspi); 1755 cqspi->current_cs = -1; 1756 cqspi->sclk = 0; 1757 1758 master->num_chipselect = cqspi->num_chipselect; 1759 1760 ret = cqspi_setup_flash(cqspi); 1761 if (ret) { 1762 dev_err(dev, "failed to setup flash parameters %d\n", ret); 1763 goto probe_setup_failed; 1764 } 1765 1766 if (cqspi->use_direct_mode) { 1767 ret = cqspi_request_mmap_dma(cqspi); 1768 if (ret == -EPROBE_DEFER) 1769 goto probe_setup_failed; 1770 } 1771 1772 ret = devm_spi_register_master(dev, master); 1773 if (ret) { 1774 dev_err(&pdev->dev, "failed to register SPI ctlr %d\n", ret); 1775 goto probe_setup_failed; 1776 } 1777 1778 return 0; 1779 probe_setup_failed: 1780 cqspi_controller_enable(cqspi, 0); 1781 probe_reset_failed: 1782 clk_disable_unprepare(cqspi->clk); 1783 probe_clk_failed: 1784 pm_runtime_put_sync(dev); 1785 pm_runtime_disable(dev); 1786 probe_master_put: 1787 spi_master_put(master); 1788 return ret; 1789 } 1790 1791 static int cqspi_remove(struct platform_device *pdev) 1792 { 1793 struct cqspi_st *cqspi = platform_get_drvdata(pdev); 1794 1795 cqspi_controller_enable(cqspi, 0); 1796 1797 if (cqspi->rx_chan) 1798 dma_release_channel(cqspi->rx_chan); 1799 1800 clk_disable_unprepare(cqspi->clk); 1801 1802 pm_runtime_put_sync(&pdev->dev); 1803 pm_runtime_disable(&pdev->dev); 1804 1805 return 0; 1806 } 1807 1808 #ifdef CONFIG_PM_SLEEP 1809 static int cqspi_suspend(struct device *dev) 1810 { 1811 struct cqspi_st *cqspi = dev_get_drvdata(dev); 1812 1813 cqspi_controller_enable(cqspi, 0); 1814 return 0; 1815 } 1816 1817 static int cqspi_resume(struct device *dev) 1818 { 1819 struct cqspi_st *cqspi = dev_get_drvdata(dev); 1820 1821 cqspi_controller_enable(cqspi, 1); 1822 return 0; 1823 } 1824 1825 static const struct dev_pm_ops cqspi__dev_pm_ops = { 1826 .suspend = cqspi_suspend, 1827 .resume = cqspi_resume, 1828 }; 1829 1830 #define CQSPI_DEV_PM_OPS (&cqspi__dev_pm_ops) 1831 #else 1832 #define CQSPI_DEV_PM_OPS NULL 1833 #endif 1834 1835 static const struct cqspi_driver_platdata cdns_qspi = { 1836 .quirks = CQSPI_DISABLE_DAC_MODE, 1837 }; 1838 1839 static const struct cqspi_driver_platdata k2g_qspi = { 1840 .quirks = CQSPI_NEEDS_WR_DELAY, 1841 }; 1842 1843 static const struct cqspi_driver_platdata am654_ospi = { 1844 .hwcaps_mask = CQSPI_SUPPORTS_OCTAL, 1845 .quirks = CQSPI_NEEDS_WR_DELAY, 1846 }; 1847 1848 static const struct cqspi_driver_platdata intel_lgm_qspi = { 1849 .quirks = CQSPI_DISABLE_DAC_MODE, 1850 }; 1851 1852 static const struct cqspi_driver_platdata socfpga_qspi = { 1853 .quirks = CQSPI_NO_SUPPORT_WR_COMPLETION, 1854 }; 1855 1856 static const struct cqspi_driver_platdata versal_ospi = { 1857 .hwcaps_mask = CQSPI_SUPPORTS_OCTAL, 1858 .quirks = CQSPI_DISABLE_DAC_MODE | CQSPI_SUPPORT_EXTERNAL_DMA, 1859 .indirect_read_dma = cqspi_versal_indirect_read_dma, 1860 .get_dma_status = cqspi_get_versal_dma_status, 1861 }; 1862 1863 static const struct of_device_id cqspi_dt_ids[] = { 1864 { 1865 .compatible = "cdns,qspi-nor", 1866 .data = &cdns_qspi, 1867 }, 1868 { 1869 .compatible = "ti,k2g-qspi", 1870 .data = &k2g_qspi, 1871 }, 1872 { 1873 .compatible = "ti,am654-ospi", 1874 .data = &am654_ospi, 1875 }, 1876 { 1877 .compatible = "intel,lgm-qspi", 1878 .data = &intel_lgm_qspi, 1879 }, 1880 { 1881 .compatible = "xlnx,versal-ospi-1.0", 1882 .data = (void *)&versal_ospi, 1883 }, 1884 { 1885 .compatible = "intel,socfpga-qspi", 1886 .data = (void *)&socfpga_qspi, 1887 }, 1888 { /* end of table */ } 1889 }; 1890 1891 MODULE_DEVICE_TABLE(of, cqspi_dt_ids); 1892 1893 static struct platform_driver cqspi_platform_driver = { 1894 .probe = cqspi_probe, 1895 .remove = cqspi_remove, 1896 .driver = { 1897 .name = CQSPI_NAME, 1898 .pm = CQSPI_DEV_PM_OPS, 1899 .of_match_table = cqspi_dt_ids, 1900 }, 1901 }; 1902 1903 module_platform_driver(cqspi_platform_driver); 1904 1905 MODULE_DESCRIPTION("Cadence QSPI Controller Driver"); 1906 MODULE_LICENSE("GPL v2"); 1907 MODULE_ALIAS("platform:" CQSPI_NAME); 1908 MODULE_AUTHOR("Ley Foon Tan <lftan@altera.com>"); 1909 MODULE_AUTHOR("Graham Moore <grmoore@opensource.altera.com>"); 1910 MODULE_AUTHOR("Vadivel Murugan R <vadivel.muruganx.ramuthevar@intel.com>"); 1911 MODULE_AUTHOR("Vignesh Raghavendra <vigneshr@ti.com>"); 1912 MODULE_AUTHOR("Pratyush Yadav <p.yadav@ti.com>"); 1913