1 // SPDX-License-Identifier: GPL-2.0-only 2 // 3 // Driver for Cadence QSPI Controller 4 // 5 // Copyright Altera Corporation (C) 2012-2014. All rights reserved. 6 // Copyright Intel Corporation (C) 2019-2020. All rights reserved. 7 // Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com 8 9 #include <linux/clk.h> 10 #include <linux/completion.h> 11 #include <linux/delay.h> 12 #include <linux/dma-mapping.h> 13 #include <linux/dmaengine.h> 14 #include <linux/err.h> 15 #include <linux/errno.h> 16 #include <linux/firmware/xlnx-zynqmp.h> 17 #include <linux/interrupt.h> 18 #include <linux/io.h> 19 #include <linux/iopoll.h> 20 #include <linux/jiffies.h> 21 #include <linux/kernel.h> 22 #include <linux/log2.h> 23 #include <linux/module.h> 24 #include <linux/of.h> 25 #include <linux/platform_device.h> 26 #include <linux/pm_runtime.h> 27 #include <linux/reset.h> 28 #include <linux/sched.h> 29 #include <linux/spi/spi.h> 30 #include <linux/spi/spi-mem.h> 31 #include <linux/timer.h> 32 33 #define CQSPI_NAME "cadence-qspi" 34 #define CQSPI_MAX_CHIPSELECT 16 35 36 /* Quirks */ 37 #define CQSPI_NEEDS_WR_DELAY BIT(0) 38 #define CQSPI_DISABLE_DAC_MODE BIT(1) 39 #define CQSPI_SUPPORT_EXTERNAL_DMA BIT(2) 40 #define CQSPI_NO_SUPPORT_WR_COMPLETION BIT(3) 41 #define CQSPI_SLOW_SRAM BIT(4) 42 #define CQSPI_NEEDS_APB_AHB_HAZARD_WAR BIT(5) 43 44 /* Capabilities */ 45 #define CQSPI_SUPPORTS_OCTAL BIT(0) 46 47 #define CQSPI_OP_WIDTH(part) ((part).nbytes ? ilog2((part).buswidth) : 0) 48 49 enum { 50 CLK_QSPI_APB = 0, 51 CLK_QSPI_AHB, 52 CLK_QSPI_NUM, 53 }; 54 55 struct cqspi_st; 56 57 struct cqspi_flash_pdata { 58 struct cqspi_st *cqspi; 59 u32 clk_rate; 60 u32 read_delay; 61 u32 tshsl_ns; 62 u32 tsd2d_ns; 63 u32 tchsh_ns; 64 u32 tslch_ns; 65 u8 cs; 66 }; 67 68 struct cqspi_st { 69 struct platform_device *pdev; 70 struct spi_controller *host; 71 struct clk *clk; 72 struct clk *clks[CLK_QSPI_NUM]; 73 unsigned int sclk; 74 75 void __iomem *iobase; 76 void __iomem *ahb_base; 77 resource_size_t ahb_size; 78 struct completion transfer_complete; 79 80 struct dma_chan *rx_chan; 81 struct completion rx_dma_complete; 82 dma_addr_t mmap_phys_base; 83 84 int current_cs; 85 unsigned long master_ref_clk_hz; 86 bool is_decoded_cs; 87 u32 fifo_depth; 88 u32 fifo_width; 89 u32 num_chipselect; 90 bool rclk_en; 91 u32 trigger_address; 92 u32 wr_delay; 93 bool use_direct_mode; 94 bool use_direct_mode_wr; 95 struct cqspi_flash_pdata f_pdata[CQSPI_MAX_CHIPSELECT]; 96 bool use_dma_read; 97 u32 pd_dev_id; 98 bool wr_completion; 99 bool slow_sram; 100 bool apb_ahb_hazard; 101 102 bool is_jh7110; /* Flag for StarFive JH7110 SoC */ 103 }; 104 105 struct cqspi_driver_platdata { 106 u32 hwcaps_mask; 107 u8 quirks; 108 int (*indirect_read_dma)(struct cqspi_flash_pdata *f_pdata, 109 u_char *rxbuf, loff_t from_addr, size_t n_rx); 110 u32 (*get_dma_status)(struct cqspi_st *cqspi); 111 int (*jh7110_clk_init)(struct platform_device *pdev, 112 struct cqspi_st *cqspi); 113 }; 114 115 /* Operation timeout value */ 116 #define CQSPI_TIMEOUT_MS 500 117 #define CQSPI_READ_TIMEOUT_MS 10 118 119 #define CQSPI_DUMMY_CLKS_PER_BYTE 8 120 #define CQSPI_DUMMY_BYTES_MAX 4 121 #define CQSPI_DUMMY_CLKS_MAX 31 122 123 #define CQSPI_STIG_DATA_LEN_MAX 8 124 125 /* Register map */ 126 #define CQSPI_REG_CONFIG 0x00 127 #define CQSPI_REG_CONFIG_ENABLE_MASK BIT(0) 128 #define CQSPI_REG_CONFIG_ENB_DIR_ACC_CTRL BIT(7) 129 #define CQSPI_REG_CONFIG_DECODE_MASK BIT(9) 130 #define CQSPI_REG_CONFIG_CHIPSELECT_LSB 10 131 #define CQSPI_REG_CONFIG_DMA_MASK BIT(15) 132 #define CQSPI_REG_CONFIG_BAUD_LSB 19 133 #define CQSPI_REG_CONFIG_DTR_PROTO BIT(24) 134 #define CQSPI_REG_CONFIG_DUAL_OPCODE BIT(30) 135 #define CQSPI_REG_CONFIG_IDLE_LSB 31 136 #define CQSPI_REG_CONFIG_CHIPSELECT_MASK 0xF 137 #define CQSPI_REG_CONFIG_BAUD_MASK 0xF 138 139 #define CQSPI_REG_RD_INSTR 0x04 140 #define CQSPI_REG_RD_INSTR_OPCODE_LSB 0 141 #define CQSPI_REG_RD_INSTR_TYPE_INSTR_LSB 8 142 #define CQSPI_REG_RD_INSTR_TYPE_ADDR_LSB 12 143 #define CQSPI_REG_RD_INSTR_TYPE_DATA_LSB 16 144 #define CQSPI_REG_RD_INSTR_MODE_EN_LSB 20 145 #define CQSPI_REG_RD_INSTR_DUMMY_LSB 24 146 #define CQSPI_REG_RD_INSTR_TYPE_INSTR_MASK 0x3 147 #define CQSPI_REG_RD_INSTR_TYPE_ADDR_MASK 0x3 148 #define CQSPI_REG_RD_INSTR_TYPE_DATA_MASK 0x3 149 #define CQSPI_REG_RD_INSTR_DUMMY_MASK 0x1F 150 151 #define CQSPI_REG_WR_INSTR 0x08 152 #define CQSPI_REG_WR_INSTR_OPCODE_LSB 0 153 #define CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB 12 154 #define CQSPI_REG_WR_INSTR_TYPE_DATA_LSB 16 155 156 #define CQSPI_REG_DELAY 0x0C 157 #define CQSPI_REG_DELAY_TSLCH_LSB 0 158 #define CQSPI_REG_DELAY_TCHSH_LSB 8 159 #define CQSPI_REG_DELAY_TSD2D_LSB 16 160 #define CQSPI_REG_DELAY_TSHSL_LSB 24 161 #define CQSPI_REG_DELAY_TSLCH_MASK 0xFF 162 #define CQSPI_REG_DELAY_TCHSH_MASK 0xFF 163 #define CQSPI_REG_DELAY_TSD2D_MASK 0xFF 164 #define CQSPI_REG_DELAY_TSHSL_MASK 0xFF 165 166 #define CQSPI_REG_READCAPTURE 0x10 167 #define CQSPI_REG_READCAPTURE_BYPASS_LSB 0 168 #define CQSPI_REG_READCAPTURE_DELAY_LSB 1 169 #define CQSPI_REG_READCAPTURE_DELAY_MASK 0xF 170 171 #define CQSPI_REG_SIZE 0x14 172 #define CQSPI_REG_SIZE_ADDRESS_LSB 0 173 #define CQSPI_REG_SIZE_PAGE_LSB 4 174 #define CQSPI_REG_SIZE_BLOCK_LSB 16 175 #define CQSPI_REG_SIZE_ADDRESS_MASK 0xF 176 #define CQSPI_REG_SIZE_PAGE_MASK 0xFFF 177 #define CQSPI_REG_SIZE_BLOCK_MASK 0x3F 178 179 #define CQSPI_REG_SRAMPARTITION 0x18 180 #define CQSPI_REG_INDIRECTTRIGGER 0x1C 181 182 #define CQSPI_REG_DMA 0x20 183 #define CQSPI_REG_DMA_SINGLE_LSB 0 184 #define CQSPI_REG_DMA_BURST_LSB 8 185 #define CQSPI_REG_DMA_SINGLE_MASK 0xFF 186 #define CQSPI_REG_DMA_BURST_MASK 0xFF 187 188 #define CQSPI_REG_REMAP 0x24 189 #define CQSPI_REG_MODE_BIT 0x28 190 191 #define CQSPI_REG_SDRAMLEVEL 0x2C 192 #define CQSPI_REG_SDRAMLEVEL_RD_LSB 0 193 #define CQSPI_REG_SDRAMLEVEL_WR_LSB 16 194 #define CQSPI_REG_SDRAMLEVEL_RD_MASK 0xFFFF 195 #define CQSPI_REG_SDRAMLEVEL_WR_MASK 0xFFFF 196 197 #define CQSPI_REG_WR_COMPLETION_CTRL 0x38 198 #define CQSPI_REG_WR_DISABLE_AUTO_POLL BIT(14) 199 200 #define CQSPI_REG_IRQSTATUS 0x40 201 #define CQSPI_REG_IRQMASK 0x44 202 203 #define CQSPI_REG_INDIRECTRD 0x60 204 #define CQSPI_REG_INDIRECTRD_START_MASK BIT(0) 205 #define CQSPI_REG_INDIRECTRD_CANCEL_MASK BIT(1) 206 #define CQSPI_REG_INDIRECTRD_DONE_MASK BIT(5) 207 208 #define CQSPI_REG_INDIRECTRDWATERMARK 0x64 209 #define CQSPI_REG_INDIRECTRDSTARTADDR 0x68 210 #define CQSPI_REG_INDIRECTRDBYTES 0x6C 211 212 #define CQSPI_REG_CMDCTRL 0x90 213 #define CQSPI_REG_CMDCTRL_EXECUTE_MASK BIT(0) 214 #define CQSPI_REG_CMDCTRL_INPROGRESS_MASK BIT(1) 215 #define CQSPI_REG_CMDCTRL_DUMMY_LSB 7 216 #define CQSPI_REG_CMDCTRL_WR_BYTES_LSB 12 217 #define CQSPI_REG_CMDCTRL_WR_EN_LSB 15 218 #define CQSPI_REG_CMDCTRL_ADD_BYTES_LSB 16 219 #define CQSPI_REG_CMDCTRL_ADDR_EN_LSB 19 220 #define CQSPI_REG_CMDCTRL_RD_BYTES_LSB 20 221 #define CQSPI_REG_CMDCTRL_RD_EN_LSB 23 222 #define CQSPI_REG_CMDCTRL_OPCODE_LSB 24 223 #define CQSPI_REG_CMDCTRL_WR_BYTES_MASK 0x7 224 #define CQSPI_REG_CMDCTRL_ADD_BYTES_MASK 0x3 225 #define CQSPI_REG_CMDCTRL_RD_BYTES_MASK 0x7 226 #define CQSPI_REG_CMDCTRL_DUMMY_MASK 0x1F 227 228 #define CQSPI_REG_INDIRECTWR 0x70 229 #define CQSPI_REG_INDIRECTWR_START_MASK BIT(0) 230 #define CQSPI_REG_INDIRECTWR_CANCEL_MASK BIT(1) 231 #define CQSPI_REG_INDIRECTWR_DONE_MASK BIT(5) 232 233 #define CQSPI_REG_INDIRECTWRWATERMARK 0x74 234 #define CQSPI_REG_INDIRECTWRSTARTADDR 0x78 235 #define CQSPI_REG_INDIRECTWRBYTES 0x7C 236 237 #define CQSPI_REG_INDTRIG_ADDRRANGE 0x80 238 239 #define CQSPI_REG_CMDADDRESS 0x94 240 #define CQSPI_REG_CMDREADDATALOWER 0xA0 241 #define CQSPI_REG_CMDREADDATAUPPER 0xA4 242 #define CQSPI_REG_CMDWRITEDATALOWER 0xA8 243 #define CQSPI_REG_CMDWRITEDATAUPPER 0xAC 244 245 #define CQSPI_REG_POLLING_STATUS 0xB0 246 #define CQSPI_REG_POLLING_STATUS_DUMMY_LSB 16 247 248 #define CQSPI_REG_OP_EXT_LOWER 0xE0 249 #define CQSPI_REG_OP_EXT_READ_LSB 24 250 #define CQSPI_REG_OP_EXT_WRITE_LSB 16 251 #define CQSPI_REG_OP_EXT_STIG_LSB 0 252 253 #define CQSPI_REG_VERSAL_DMA_SRC_ADDR 0x1000 254 255 #define CQSPI_REG_VERSAL_DMA_DST_ADDR 0x1800 256 #define CQSPI_REG_VERSAL_DMA_DST_SIZE 0x1804 257 258 #define CQSPI_REG_VERSAL_DMA_DST_CTRL 0x180C 259 260 #define CQSPI_REG_VERSAL_DMA_DST_I_STS 0x1814 261 #define CQSPI_REG_VERSAL_DMA_DST_I_EN 0x1818 262 #define CQSPI_REG_VERSAL_DMA_DST_I_DIS 0x181C 263 #define CQSPI_REG_VERSAL_DMA_DST_DONE_MASK BIT(1) 264 265 #define CQSPI_REG_VERSAL_DMA_DST_ADDR_MSB 0x1828 266 267 #define CQSPI_REG_VERSAL_DMA_DST_CTRL_VAL 0xF43FFA00 268 #define CQSPI_REG_VERSAL_ADDRRANGE_WIDTH_VAL 0x6 269 270 /* Interrupt status bits */ 271 #define CQSPI_REG_IRQ_MODE_ERR BIT(0) 272 #define CQSPI_REG_IRQ_UNDERFLOW BIT(1) 273 #define CQSPI_REG_IRQ_IND_COMP BIT(2) 274 #define CQSPI_REG_IRQ_IND_RD_REJECT BIT(3) 275 #define CQSPI_REG_IRQ_WR_PROTECTED_ERR BIT(4) 276 #define CQSPI_REG_IRQ_ILLEGAL_AHB_ERR BIT(5) 277 #define CQSPI_REG_IRQ_WATERMARK BIT(6) 278 #define CQSPI_REG_IRQ_IND_SRAM_FULL BIT(12) 279 280 #define CQSPI_IRQ_MASK_RD (CQSPI_REG_IRQ_WATERMARK | \ 281 CQSPI_REG_IRQ_IND_SRAM_FULL | \ 282 CQSPI_REG_IRQ_IND_COMP) 283 284 #define CQSPI_IRQ_MASK_WR (CQSPI_REG_IRQ_IND_COMP | \ 285 CQSPI_REG_IRQ_WATERMARK | \ 286 CQSPI_REG_IRQ_UNDERFLOW) 287 288 #define CQSPI_IRQ_STATUS_MASK 0x1FFFF 289 #define CQSPI_DMA_UNALIGN 0x3 290 291 #define CQSPI_REG_VERSAL_DMA_VAL 0x602 292 293 static int cqspi_wait_for_bit(void __iomem *reg, const u32 mask, bool clr) 294 { 295 u32 val; 296 297 return readl_relaxed_poll_timeout(reg, val, 298 (((clr ? ~val : val) & mask) == mask), 299 10, CQSPI_TIMEOUT_MS * 1000); 300 } 301 302 static bool cqspi_is_idle(struct cqspi_st *cqspi) 303 { 304 u32 reg = readl(cqspi->iobase + CQSPI_REG_CONFIG); 305 306 return reg & (1UL << CQSPI_REG_CONFIG_IDLE_LSB); 307 } 308 309 static u32 cqspi_get_rd_sram_level(struct cqspi_st *cqspi) 310 { 311 u32 reg = readl(cqspi->iobase + CQSPI_REG_SDRAMLEVEL); 312 313 reg >>= CQSPI_REG_SDRAMLEVEL_RD_LSB; 314 return reg & CQSPI_REG_SDRAMLEVEL_RD_MASK; 315 } 316 317 static u32 cqspi_get_versal_dma_status(struct cqspi_st *cqspi) 318 { 319 u32 dma_status; 320 321 dma_status = readl(cqspi->iobase + 322 CQSPI_REG_VERSAL_DMA_DST_I_STS); 323 writel(dma_status, cqspi->iobase + 324 CQSPI_REG_VERSAL_DMA_DST_I_STS); 325 326 return dma_status & CQSPI_REG_VERSAL_DMA_DST_DONE_MASK; 327 } 328 329 static irqreturn_t cqspi_irq_handler(int this_irq, void *dev) 330 { 331 struct cqspi_st *cqspi = dev; 332 unsigned int irq_status; 333 struct device *device = &cqspi->pdev->dev; 334 const struct cqspi_driver_platdata *ddata; 335 336 ddata = of_device_get_match_data(device); 337 338 /* Read interrupt status */ 339 irq_status = readl(cqspi->iobase + CQSPI_REG_IRQSTATUS); 340 341 /* Clear interrupt */ 342 writel(irq_status, cqspi->iobase + CQSPI_REG_IRQSTATUS); 343 344 if (cqspi->use_dma_read && ddata && ddata->get_dma_status) { 345 if (ddata->get_dma_status(cqspi)) { 346 complete(&cqspi->transfer_complete); 347 return IRQ_HANDLED; 348 } 349 } 350 351 else if (!cqspi->slow_sram) 352 irq_status &= CQSPI_IRQ_MASK_RD | CQSPI_IRQ_MASK_WR; 353 else 354 irq_status &= CQSPI_REG_IRQ_WATERMARK | CQSPI_IRQ_MASK_WR; 355 356 if (irq_status) 357 complete(&cqspi->transfer_complete); 358 359 return IRQ_HANDLED; 360 } 361 362 static unsigned int cqspi_calc_rdreg(const struct spi_mem_op *op) 363 { 364 u32 rdreg = 0; 365 366 rdreg |= CQSPI_OP_WIDTH(op->cmd) << CQSPI_REG_RD_INSTR_TYPE_INSTR_LSB; 367 rdreg |= CQSPI_OP_WIDTH(op->addr) << CQSPI_REG_RD_INSTR_TYPE_ADDR_LSB; 368 rdreg |= CQSPI_OP_WIDTH(op->data) << CQSPI_REG_RD_INSTR_TYPE_DATA_LSB; 369 370 return rdreg; 371 } 372 373 static unsigned int cqspi_calc_dummy(const struct spi_mem_op *op) 374 { 375 unsigned int dummy_clk; 376 377 if (!op->dummy.nbytes) 378 return 0; 379 380 dummy_clk = op->dummy.nbytes * (8 / op->dummy.buswidth); 381 if (op->cmd.dtr) 382 dummy_clk /= 2; 383 384 return dummy_clk; 385 } 386 387 static int cqspi_wait_idle(struct cqspi_st *cqspi) 388 { 389 const unsigned int poll_idle_retry = 3; 390 unsigned int count = 0; 391 unsigned long timeout; 392 393 timeout = jiffies + msecs_to_jiffies(CQSPI_TIMEOUT_MS); 394 while (1) { 395 /* 396 * Read few times in succession to ensure the controller 397 * is indeed idle, that is, the bit does not transition 398 * low again. 399 */ 400 if (cqspi_is_idle(cqspi)) 401 count++; 402 else 403 count = 0; 404 405 if (count >= poll_idle_retry) 406 return 0; 407 408 if (time_after(jiffies, timeout)) { 409 /* Timeout, in busy mode. */ 410 dev_err(&cqspi->pdev->dev, 411 "QSPI is still busy after %dms timeout.\n", 412 CQSPI_TIMEOUT_MS); 413 return -ETIMEDOUT; 414 } 415 416 cpu_relax(); 417 } 418 } 419 420 static int cqspi_exec_flash_cmd(struct cqspi_st *cqspi, unsigned int reg) 421 { 422 void __iomem *reg_base = cqspi->iobase; 423 int ret; 424 425 /* Write the CMDCTRL without start execution. */ 426 writel(reg, reg_base + CQSPI_REG_CMDCTRL); 427 /* Start execute */ 428 reg |= CQSPI_REG_CMDCTRL_EXECUTE_MASK; 429 writel(reg, reg_base + CQSPI_REG_CMDCTRL); 430 431 /* Polling for completion. */ 432 ret = cqspi_wait_for_bit(reg_base + CQSPI_REG_CMDCTRL, 433 CQSPI_REG_CMDCTRL_INPROGRESS_MASK, 1); 434 if (ret) { 435 dev_err(&cqspi->pdev->dev, 436 "Flash command execution timed out.\n"); 437 return ret; 438 } 439 440 /* Polling QSPI idle status. */ 441 return cqspi_wait_idle(cqspi); 442 } 443 444 static int cqspi_setup_opcode_ext(struct cqspi_flash_pdata *f_pdata, 445 const struct spi_mem_op *op, 446 unsigned int shift) 447 { 448 struct cqspi_st *cqspi = f_pdata->cqspi; 449 void __iomem *reg_base = cqspi->iobase; 450 unsigned int reg; 451 u8 ext; 452 453 if (op->cmd.nbytes != 2) 454 return -EINVAL; 455 456 /* Opcode extension is the LSB. */ 457 ext = op->cmd.opcode & 0xff; 458 459 reg = readl(reg_base + CQSPI_REG_OP_EXT_LOWER); 460 reg &= ~(0xff << shift); 461 reg |= ext << shift; 462 writel(reg, reg_base + CQSPI_REG_OP_EXT_LOWER); 463 464 return 0; 465 } 466 467 static int cqspi_enable_dtr(struct cqspi_flash_pdata *f_pdata, 468 const struct spi_mem_op *op, unsigned int shift) 469 { 470 struct cqspi_st *cqspi = f_pdata->cqspi; 471 void __iomem *reg_base = cqspi->iobase; 472 unsigned int reg; 473 int ret; 474 475 reg = readl(reg_base + CQSPI_REG_CONFIG); 476 477 /* 478 * We enable dual byte opcode here. The callers have to set up the 479 * extension opcode based on which type of operation it is. 480 */ 481 if (op->cmd.dtr) { 482 reg |= CQSPI_REG_CONFIG_DTR_PROTO; 483 reg |= CQSPI_REG_CONFIG_DUAL_OPCODE; 484 485 /* Set up command opcode extension. */ 486 ret = cqspi_setup_opcode_ext(f_pdata, op, shift); 487 if (ret) 488 return ret; 489 } else { 490 reg &= ~CQSPI_REG_CONFIG_DTR_PROTO; 491 reg &= ~CQSPI_REG_CONFIG_DUAL_OPCODE; 492 } 493 494 writel(reg, reg_base + CQSPI_REG_CONFIG); 495 496 return cqspi_wait_idle(cqspi); 497 } 498 499 static int cqspi_command_read(struct cqspi_flash_pdata *f_pdata, 500 const struct spi_mem_op *op) 501 { 502 struct cqspi_st *cqspi = f_pdata->cqspi; 503 void __iomem *reg_base = cqspi->iobase; 504 u8 *rxbuf = op->data.buf.in; 505 u8 opcode; 506 size_t n_rx = op->data.nbytes; 507 unsigned int rdreg; 508 unsigned int reg; 509 unsigned int dummy_clk; 510 size_t read_len; 511 int status; 512 513 status = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_STIG_LSB); 514 if (status) 515 return status; 516 517 if (!n_rx || n_rx > CQSPI_STIG_DATA_LEN_MAX || !rxbuf) { 518 dev_err(&cqspi->pdev->dev, 519 "Invalid input argument, len %zu rxbuf 0x%p\n", 520 n_rx, rxbuf); 521 return -EINVAL; 522 } 523 524 if (op->cmd.dtr) 525 opcode = op->cmd.opcode >> 8; 526 else 527 opcode = op->cmd.opcode; 528 529 reg = opcode << CQSPI_REG_CMDCTRL_OPCODE_LSB; 530 531 rdreg = cqspi_calc_rdreg(op); 532 writel(rdreg, reg_base + CQSPI_REG_RD_INSTR); 533 534 dummy_clk = cqspi_calc_dummy(op); 535 if (dummy_clk > CQSPI_DUMMY_CLKS_MAX) 536 return -EOPNOTSUPP; 537 538 if (dummy_clk) 539 reg |= (dummy_clk & CQSPI_REG_CMDCTRL_DUMMY_MASK) 540 << CQSPI_REG_CMDCTRL_DUMMY_LSB; 541 542 reg |= (0x1 << CQSPI_REG_CMDCTRL_RD_EN_LSB); 543 544 /* 0 means 1 byte. */ 545 reg |= (((n_rx - 1) & CQSPI_REG_CMDCTRL_RD_BYTES_MASK) 546 << CQSPI_REG_CMDCTRL_RD_BYTES_LSB); 547 548 /* setup ADDR BIT field */ 549 if (op->addr.nbytes) { 550 reg |= (0x1 << CQSPI_REG_CMDCTRL_ADDR_EN_LSB); 551 reg |= ((op->addr.nbytes - 1) & 552 CQSPI_REG_CMDCTRL_ADD_BYTES_MASK) 553 << CQSPI_REG_CMDCTRL_ADD_BYTES_LSB; 554 555 writel(op->addr.val, reg_base + CQSPI_REG_CMDADDRESS); 556 } 557 558 status = cqspi_exec_flash_cmd(cqspi, reg); 559 if (status) 560 return status; 561 562 reg = readl(reg_base + CQSPI_REG_CMDREADDATALOWER); 563 564 /* Put the read value into rx_buf */ 565 read_len = (n_rx > 4) ? 4 : n_rx; 566 memcpy(rxbuf, ®, read_len); 567 rxbuf += read_len; 568 569 if (n_rx > 4) { 570 reg = readl(reg_base + CQSPI_REG_CMDREADDATAUPPER); 571 572 read_len = n_rx - read_len; 573 memcpy(rxbuf, ®, read_len); 574 } 575 576 /* Reset CMD_CTRL Reg once command read completes */ 577 writel(0, reg_base + CQSPI_REG_CMDCTRL); 578 579 return 0; 580 } 581 582 static int cqspi_command_write(struct cqspi_flash_pdata *f_pdata, 583 const struct spi_mem_op *op) 584 { 585 struct cqspi_st *cqspi = f_pdata->cqspi; 586 void __iomem *reg_base = cqspi->iobase; 587 u8 opcode; 588 const u8 *txbuf = op->data.buf.out; 589 size_t n_tx = op->data.nbytes; 590 unsigned int reg; 591 unsigned int data; 592 size_t write_len; 593 int ret; 594 595 ret = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_STIG_LSB); 596 if (ret) 597 return ret; 598 599 if (n_tx > CQSPI_STIG_DATA_LEN_MAX || (n_tx && !txbuf)) { 600 dev_err(&cqspi->pdev->dev, 601 "Invalid input argument, cmdlen %zu txbuf 0x%p\n", 602 n_tx, txbuf); 603 return -EINVAL; 604 } 605 606 reg = cqspi_calc_rdreg(op); 607 writel(reg, reg_base + CQSPI_REG_RD_INSTR); 608 609 if (op->cmd.dtr) 610 opcode = op->cmd.opcode >> 8; 611 else 612 opcode = op->cmd.opcode; 613 614 reg = opcode << CQSPI_REG_CMDCTRL_OPCODE_LSB; 615 616 if (op->addr.nbytes) { 617 reg |= (0x1 << CQSPI_REG_CMDCTRL_ADDR_EN_LSB); 618 reg |= ((op->addr.nbytes - 1) & 619 CQSPI_REG_CMDCTRL_ADD_BYTES_MASK) 620 << CQSPI_REG_CMDCTRL_ADD_BYTES_LSB; 621 622 writel(op->addr.val, reg_base + CQSPI_REG_CMDADDRESS); 623 } 624 625 if (n_tx) { 626 reg |= (0x1 << CQSPI_REG_CMDCTRL_WR_EN_LSB); 627 reg |= ((n_tx - 1) & CQSPI_REG_CMDCTRL_WR_BYTES_MASK) 628 << CQSPI_REG_CMDCTRL_WR_BYTES_LSB; 629 data = 0; 630 write_len = (n_tx > 4) ? 4 : n_tx; 631 memcpy(&data, txbuf, write_len); 632 txbuf += write_len; 633 writel(data, reg_base + CQSPI_REG_CMDWRITEDATALOWER); 634 635 if (n_tx > 4) { 636 data = 0; 637 write_len = n_tx - 4; 638 memcpy(&data, txbuf, write_len); 639 writel(data, reg_base + CQSPI_REG_CMDWRITEDATAUPPER); 640 } 641 } 642 643 ret = cqspi_exec_flash_cmd(cqspi, reg); 644 645 /* Reset CMD_CTRL Reg once command write completes */ 646 writel(0, reg_base + CQSPI_REG_CMDCTRL); 647 648 return ret; 649 } 650 651 static int cqspi_read_setup(struct cqspi_flash_pdata *f_pdata, 652 const struct spi_mem_op *op) 653 { 654 struct cqspi_st *cqspi = f_pdata->cqspi; 655 void __iomem *reg_base = cqspi->iobase; 656 unsigned int dummy_clk = 0; 657 unsigned int reg; 658 int ret; 659 u8 opcode; 660 661 ret = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_READ_LSB); 662 if (ret) 663 return ret; 664 665 if (op->cmd.dtr) 666 opcode = op->cmd.opcode >> 8; 667 else 668 opcode = op->cmd.opcode; 669 670 reg = opcode << CQSPI_REG_RD_INSTR_OPCODE_LSB; 671 reg |= cqspi_calc_rdreg(op); 672 673 /* Setup dummy clock cycles */ 674 dummy_clk = cqspi_calc_dummy(op); 675 676 if (dummy_clk > CQSPI_DUMMY_CLKS_MAX) 677 return -EOPNOTSUPP; 678 679 if (dummy_clk) 680 reg |= (dummy_clk & CQSPI_REG_RD_INSTR_DUMMY_MASK) 681 << CQSPI_REG_RD_INSTR_DUMMY_LSB; 682 683 writel(reg, reg_base + CQSPI_REG_RD_INSTR); 684 685 /* Set address width */ 686 reg = readl(reg_base + CQSPI_REG_SIZE); 687 reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK; 688 reg |= (op->addr.nbytes - 1); 689 writel(reg, reg_base + CQSPI_REG_SIZE); 690 return 0; 691 } 692 693 static int cqspi_indirect_read_execute(struct cqspi_flash_pdata *f_pdata, 694 u8 *rxbuf, loff_t from_addr, 695 const size_t n_rx) 696 { 697 struct cqspi_st *cqspi = f_pdata->cqspi; 698 struct device *dev = &cqspi->pdev->dev; 699 void __iomem *reg_base = cqspi->iobase; 700 void __iomem *ahb_base = cqspi->ahb_base; 701 unsigned int remaining = n_rx; 702 unsigned int mod_bytes = n_rx % 4; 703 unsigned int bytes_to_read = 0; 704 u8 *rxbuf_end = rxbuf + n_rx; 705 int ret = 0; 706 707 writel(from_addr, reg_base + CQSPI_REG_INDIRECTRDSTARTADDR); 708 writel(remaining, reg_base + CQSPI_REG_INDIRECTRDBYTES); 709 710 /* Clear all interrupts. */ 711 writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS); 712 713 /* 714 * On SoCFPGA platform reading the SRAM is slow due to 715 * hardware limitation and causing read interrupt storm to CPU, 716 * so enabling only watermark interrupt to disable all read 717 * interrupts later as we want to run "bytes to read" loop with 718 * all the read interrupts disabled for max performance. 719 */ 720 721 if (!cqspi->slow_sram) 722 writel(CQSPI_IRQ_MASK_RD, reg_base + CQSPI_REG_IRQMASK); 723 else 724 writel(CQSPI_REG_IRQ_WATERMARK, reg_base + CQSPI_REG_IRQMASK); 725 726 reinit_completion(&cqspi->transfer_complete); 727 writel(CQSPI_REG_INDIRECTRD_START_MASK, 728 reg_base + CQSPI_REG_INDIRECTRD); 729 730 while (remaining > 0) { 731 if (!wait_for_completion_timeout(&cqspi->transfer_complete, 732 msecs_to_jiffies(CQSPI_READ_TIMEOUT_MS))) 733 ret = -ETIMEDOUT; 734 735 /* 736 * Disable all read interrupts until 737 * we are out of "bytes to read" 738 */ 739 if (cqspi->slow_sram) 740 writel(0x0, reg_base + CQSPI_REG_IRQMASK); 741 742 bytes_to_read = cqspi_get_rd_sram_level(cqspi); 743 744 if (ret && bytes_to_read == 0) { 745 dev_err(dev, "Indirect read timeout, no bytes\n"); 746 goto failrd; 747 } 748 749 while (bytes_to_read != 0) { 750 unsigned int word_remain = round_down(remaining, 4); 751 752 bytes_to_read *= cqspi->fifo_width; 753 bytes_to_read = bytes_to_read > remaining ? 754 remaining : bytes_to_read; 755 bytes_to_read = round_down(bytes_to_read, 4); 756 /* Read 4 byte word chunks then single bytes */ 757 if (bytes_to_read) { 758 ioread32_rep(ahb_base, rxbuf, 759 (bytes_to_read / 4)); 760 } else if (!word_remain && mod_bytes) { 761 unsigned int temp = ioread32(ahb_base); 762 763 bytes_to_read = mod_bytes; 764 memcpy(rxbuf, &temp, min((unsigned int) 765 (rxbuf_end - rxbuf), 766 bytes_to_read)); 767 } 768 rxbuf += bytes_to_read; 769 remaining -= bytes_to_read; 770 bytes_to_read = cqspi_get_rd_sram_level(cqspi); 771 } 772 773 if (remaining > 0) { 774 reinit_completion(&cqspi->transfer_complete); 775 if (cqspi->slow_sram) 776 writel(CQSPI_REG_IRQ_WATERMARK, reg_base + CQSPI_REG_IRQMASK); 777 } 778 } 779 780 /* Check indirect done status */ 781 ret = cqspi_wait_for_bit(reg_base + CQSPI_REG_INDIRECTRD, 782 CQSPI_REG_INDIRECTRD_DONE_MASK, 0); 783 if (ret) { 784 dev_err(dev, "Indirect read completion error (%i)\n", ret); 785 goto failrd; 786 } 787 788 /* Disable interrupt */ 789 writel(0, reg_base + CQSPI_REG_IRQMASK); 790 791 /* Clear indirect completion status */ 792 writel(CQSPI_REG_INDIRECTRD_DONE_MASK, reg_base + CQSPI_REG_INDIRECTRD); 793 794 return 0; 795 796 failrd: 797 /* Disable interrupt */ 798 writel(0, reg_base + CQSPI_REG_IRQMASK); 799 800 /* Cancel the indirect read */ 801 writel(CQSPI_REG_INDIRECTRD_CANCEL_MASK, 802 reg_base + CQSPI_REG_INDIRECTRD); 803 return ret; 804 } 805 806 static void cqspi_controller_enable(struct cqspi_st *cqspi, bool enable) 807 { 808 void __iomem *reg_base = cqspi->iobase; 809 unsigned int reg; 810 811 reg = readl(reg_base + CQSPI_REG_CONFIG); 812 813 if (enable) 814 reg |= CQSPI_REG_CONFIG_ENABLE_MASK; 815 else 816 reg &= ~CQSPI_REG_CONFIG_ENABLE_MASK; 817 818 writel(reg, reg_base + CQSPI_REG_CONFIG); 819 } 820 821 static int cqspi_versal_indirect_read_dma(struct cqspi_flash_pdata *f_pdata, 822 u_char *rxbuf, loff_t from_addr, 823 size_t n_rx) 824 { 825 struct cqspi_st *cqspi = f_pdata->cqspi; 826 struct device *dev = &cqspi->pdev->dev; 827 void __iomem *reg_base = cqspi->iobase; 828 u32 reg, bytes_to_dma; 829 loff_t addr = from_addr; 830 void *buf = rxbuf; 831 dma_addr_t dma_addr; 832 u8 bytes_rem; 833 int ret = 0; 834 835 bytes_rem = n_rx % 4; 836 bytes_to_dma = (n_rx - bytes_rem); 837 838 if (!bytes_to_dma) 839 goto nondmard; 840 841 ret = zynqmp_pm_ospi_mux_select(cqspi->pd_dev_id, PM_OSPI_MUX_SEL_DMA); 842 if (ret) 843 return ret; 844 845 cqspi_controller_enable(cqspi, 0); 846 847 reg = readl(cqspi->iobase + CQSPI_REG_CONFIG); 848 reg |= CQSPI_REG_CONFIG_DMA_MASK; 849 writel(reg, cqspi->iobase + CQSPI_REG_CONFIG); 850 851 cqspi_controller_enable(cqspi, 1); 852 853 dma_addr = dma_map_single(dev, rxbuf, bytes_to_dma, DMA_FROM_DEVICE); 854 if (dma_mapping_error(dev, dma_addr)) { 855 dev_err(dev, "dma mapping failed\n"); 856 return -ENOMEM; 857 } 858 859 writel(from_addr, reg_base + CQSPI_REG_INDIRECTRDSTARTADDR); 860 writel(bytes_to_dma, reg_base + CQSPI_REG_INDIRECTRDBYTES); 861 writel(CQSPI_REG_VERSAL_ADDRRANGE_WIDTH_VAL, 862 reg_base + CQSPI_REG_INDTRIG_ADDRRANGE); 863 864 /* Clear all interrupts. */ 865 writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS); 866 867 /* Enable DMA done interrupt */ 868 writel(CQSPI_REG_VERSAL_DMA_DST_DONE_MASK, 869 reg_base + CQSPI_REG_VERSAL_DMA_DST_I_EN); 870 871 /* Default DMA periph configuration */ 872 writel(CQSPI_REG_VERSAL_DMA_VAL, reg_base + CQSPI_REG_DMA); 873 874 /* Configure DMA Dst address */ 875 writel(lower_32_bits(dma_addr), 876 reg_base + CQSPI_REG_VERSAL_DMA_DST_ADDR); 877 writel(upper_32_bits(dma_addr), 878 reg_base + CQSPI_REG_VERSAL_DMA_DST_ADDR_MSB); 879 880 /* Configure DMA Src address */ 881 writel(cqspi->trigger_address, reg_base + 882 CQSPI_REG_VERSAL_DMA_SRC_ADDR); 883 884 /* Set DMA destination size */ 885 writel(bytes_to_dma, reg_base + CQSPI_REG_VERSAL_DMA_DST_SIZE); 886 887 /* Set DMA destination control */ 888 writel(CQSPI_REG_VERSAL_DMA_DST_CTRL_VAL, 889 reg_base + CQSPI_REG_VERSAL_DMA_DST_CTRL); 890 891 writel(CQSPI_REG_INDIRECTRD_START_MASK, 892 reg_base + CQSPI_REG_INDIRECTRD); 893 894 reinit_completion(&cqspi->transfer_complete); 895 896 if (!wait_for_completion_timeout(&cqspi->transfer_complete, 897 msecs_to_jiffies(max_t(size_t, bytes_to_dma, 500)))) { 898 ret = -ETIMEDOUT; 899 goto failrd; 900 } 901 902 /* Disable DMA interrupt */ 903 writel(0x0, cqspi->iobase + CQSPI_REG_VERSAL_DMA_DST_I_DIS); 904 905 /* Clear indirect completion status */ 906 writel(CQSPI_REG_INDIRECTRD_DONE_MASK, 907 cqspi->iobase + CQSPI_REG_INDIRECTRD); 908 dma_unmap_single(dev, dma_addr, bytes_to_dma, DMA_FROM_DEVICE); 909 910 cqspi_controller_enable(cqspi, 0); 911 912 reg = readl(cqspi->iobase + CQSPI_REG_CONFIG); 913 reg &= ~CQSPI_REG_CONFIG_DMA_MASK; 914 writel(reg, cqspi->iobase + CQSPI_REG_CONFIG); 915 916 cqspi_controller_enable(cqspi, 1); 917 918 ret = zynqmp_pm_ospi_mux_select(cqspi->pd_dev_id, 919 PM_OSPI_MUX_SEL_LINEAR); 920 if (ret) 921 return ret; 922 923 nondmard: 924 if (bytes_rem) { 925 addr += bytes_to_dma; 926 buf += bytes_to_dma; 927 ret = cqspi_indirect_read_execute(f_pdata, buf, addr, 928 bytes_rem); 929 if (ret) 930 return ret; 931 } 932 933 return 0; 934 935 failrd: 936 /* Disable DMA interrupt */ 937 writel(0x0, reg_base + CQSPI_REG_VERSAL_DMA_DST_I_DIS); 938 939 /* Cancel the indirect read */ 940 writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK, 941 reg_base + CQSPI_REG_INDIRECTRD); 942 943 dma_unmap_single(dev, dma_addr, bytes_to_dma, DMA_FROM_DEVICE); 944 945 reg = readl(cqspi->iobase + CQSPI_REG_CONFIG); 946 reg &= ~CQSPI_REG_CONFIG_DMA_MASK; 947 writel(reg, cqspi->iobase + CQSPI_REG_CONFIG); 948 949 zynqmp_pm_ospi_mux_select(cqspi->pd_dev_id, PM_OSPI_MUX_SEL_LINEAR); 950 951 return ret; 952 } 953 954 static int cqspi_write_setup(struct cqspi_flash_pdata *f_pdata, 955 const struct spi_mem_op *op) 956 { 957 unsigned int reg; 958 int ret; 959 struct cqspi_st *cqspi = f_pdata->cqspi; 960 void __iomem *reg_base = cqspi->iobase; 961 u8 opcode; 962 963 ret = cqspi_enable_dtr(f_pdata, op, CQSPI_REG_OP_EXT_WRITE_LSB); 964 if (ret) 965 return ret; 966 967 if (op->cmd.dtr) 968 opcode = op->cmd.opcode >> 8; 969 else 970 opcode = op->cmd.opcode; 971 972 /* Set opcode. */ 973 reg = opcode << CQSPI_REG_WR_INSTR_OPCODE_LSB; 974 reg |= CQSPI_OP_WIDTH(op->data) << CQSPI_REG_WR_INSTR_TYPE_DATA_LSB; 975 reg |= CQSPI_OP_WIDTH(op->addr) << CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB; 976 writel(reg, reg_base + CQSPI_REG_WR_INSTR); 977 reg = cqspi_calc_rdreg(op); 978 writel(reg, reg_base + CQSPI_REG_RD_INSTR); 979 980 /* 981 * SPI NAND flashes require the address of the status register to be 982 * passed in the Read SR command. Also, some SPI NOR flashes like the 983 * cypress Semper flash expect a 4-byte dummy address in the Read SR 984 * command in DTR mode. 985 * 986 * But this controller does not support address phase in the Read SR 987 * command when doing auto-HW polling. So, disable write completion 988 * polling on the controller's side. spinand and spi-nor will take 989 * care of polling the status register. 990 */ 991 if (cqspi->wr_completion) { 992 reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL); 993 reg |= CQSPI_REG_WR_DISABLE_AUTO_POLL; 994 writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL); 995 /* 996 * DAC mode require auto polling as flash needs to be polled 997 * for write completion in case of bubble in SPI transaction 998 * due to slow CPU/DMA master. 999 */ 1000 cqspi->use_direct_mode_wr = false; 1001 } 1002 1003 reg = readl(reg_base + CQSPI_REG_SIZE); 1004 reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK; 1005 reg |= (op->addr.nbytes - 1); 1006 writel(reg, reg_base + CQSPI_REG_SIZE); 1007 return 0; 1008 } 1009 1010 static int cqspi_indirect_write_execute(struct cqspi_flash_pdata *f_pdata, 1011 loff_t to_addr, const u8 *txbuf, 1012 const size_t n_tx) 1013 { 1014 struct cqspi_st *cqspi = f_pdata->cqspi; 1015 struct device *dev = &cqspi->pdev->dev; 1016 void __iomem *reg_base = cqspi->iobase; 1017 unsigned int remaining = n_tx; 1018 unsigned int write_bytes; 1019 int ret; 1020 1021 writel(to_addr, reg_base + CQSPI_REG_INDIRECTWRSTARTADDR); 1022 writel(remaining, reg_base + CQSPI_REG_INDIRECTWRBYTES); 1023 1024 /* Clear all interrupts. */ 1025 writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS); 1026 1027 writel(CQSPI_IRQ_MASK_WR, reg_base + CQSPI_REG_IRQMASK); 1028 1029 reinit_completion(&cqspi->transfer_complete); 1030 writel(CQSPI_REG_INDIRECTWR_START_MASK, 1031 reg_base + CQSPI_REG_INDIRECTWR); 1032 /* 1033 * As per 66AK2G02 TRM SPRUHY8F section 11.15.5.3 Indirect Access 1034 * Controller programming sequence, couple of cycles of 1035 * QSPI_REF_CLK delay is required for the above bit to 1036 * be internally synchronized by the QSPI module. Provide 5 1037 * cycles of delay. 1038 */ 1039 if (cqspi->wr_delay) 1040 ndelay(cqspi->wr_delay); 1041 1042 /* 1043 * If a hazard exists between the APB and AHB interfaces, perform a 1044 * dummy readback from the controller to ensure synchronization. 1045 */ 1046 if (cqspi->apb_ahb_hazard) 1047 readl(reg_base + CQSPI_REG_INDIRECTWR); 1048 1049 while (remaining > 0) { 1050 size_t write_words, mod_bytes; 1051 1052 write_bytes = remaining; 1053 write_words = write_bytes / 4; 1054 mod_bytes = write_bytes % 4; 1055 /* Write 4 bytes at a time then single bytes. */ 1056 if (write_words) { 1057 iowrite32_rep(cqspi->ahb_base, txbuf, write_words); 1058 txbuf += (write_words * 4); 1059 } 1060 if (mod_bytes) { 1061 unsigned int temp = 0xFFFFFFFF; 1062 1063 memcpy(&temp, txbuf, mod_bytes); 1064 iowrite32(temp, cqspi->ahb_base); 1065 txbuf += mod_bytes; 1066 } 1067 1068 if (!wait_for_completion_timeout(&cqspi->transfer_complete, 1069 msecs_to_jiffies(CQSPI_TIMEOUT_MS))) { 1070 dev_err(dev, "Indirect write timeout\n"); 1071 ret = -ETIMEDOUT; 1072 goto failwr; 1073 } 1074 1075 remaining -= write_bytes; 1076 1077 if (remaining > 0) 1078 reinit_completion(&cqspi->transfer_complete); 1079 } 1080 1081 /* Check indirect done status */ 1082 ret = cqspi_wait_for_bit(reg_base + CQSPI_REG_INDIRECTWR, 1083 CQSPI_REG_INDIRECTWR_DONE_MASK, 0); 1084 if (ret) { 1085 dev_err(dev, "Indirect write completion error (%i)\n", ret); 1086 goto failwr; 1087 } 1088 1089 /* Disable interrupt. */ 1090 writel(0, reg_base + CQSPI_REG_IRQMASK); 1091 1092 /* Clear indirect completion status */ 1093 writel(CQSPI_REG_INDIRECTWR_DONE_MASK, reg_base + CQSPI_REG_INDIRECTWR); 1094 1095 cqspi_wait_idle(cqspi); 1096 1097 return 0; 1098 1099 failwr: 1100 /* Disable interrupt. */ 1101 writel(0, reg_base + CQSPI_REG_IRQMASK); 1102 1103 /* Cancel the indirect write */ 1104 writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK, 1105 reg_base + CQSPI_REG_INDIRECTWR); 1106 return ret; 1107 } 1108 1109 static void cqspi_chipselect(struct cqspi_flash_pdata *f_pdata) 1110 { 1111 struct cqspi_st *cqspi = f_pdata->cqspi; 1112 void __iomem *reg_base = cqspi->iobase; 1113 unsigned int chip_select = f_pdata->cs; 1114 unsigned int reg; 1115 1116 reg = readl(reg_base + CQSPI_REG_CONFIG); 1117 if (cqspi->is_decoded_cs) { 1118 reg |= CQSPI_REG_CONFIG_DECODE_MASK; 1119 } else { 1120 reg &= ~CQSPI_REG_CONFIG_DECODE_MASK; 1121 1122 /* Convert CS if without decoder. 1123 * CS0 to 4b'1110 1124 * CS1 to 4b'1101 1125 * CS2 to 4b'1011 1126 * CS3 to 4b'0111 1127 */ 1128 chip_select = 0xF & ~(1 << chip_select); 1129 } 1130 1131 reg &= ~(CQSPI_REG_CONFIG_CHIPSELECT_MASK 1132 << CQSPI_REG_CONFIG_CHIPSELECT_LSB); 1133 reg |= (chip_select & CQSPI_REG_CONFIG_CHIPSELECT_MASK) 1134 << CQSPI_REG_CONFIG_CHIPSELECT_LSB; 1135 writel(reg, reg_base + CQSPI_REG_CONFIG); 1136 } 1137 1138 static unsigned int calculate_ticks_for_ns(const unsigned int ref_clk_hz, 1139 const unsigned int ns_val) 1140 { 1141 unsigned int ticks; 1142 1143 ticks = ref_clk_hz / 1000; /* kHz */ 1144 ticks = DIV_ROUND_UP(ticks * ns_val, 1000000); 1145 1146 return ticks; 1147 } 1148 1149 static void cqspi_delay(struct cqspi_flash_pdata *f_pdata) 1150 { 1151 struct cqspi_st *cqspi = f_pdata->cqspi; 1152 void __iomem *iobase = cqspi->iobase; 1153 const unsigned int ref_clk_hz = cqspi->master_ref_clk_hz; 1154 unsigned int tshsl, tchsh, tslch, tsd2d; 1155 unsigned int reg; 1156 unsigned int tsclk; 1157 1158 /* calculate the number of ref ticks for one sclk tick */ 1159 tsclk = DIV_ROUND_UP(ref_clk_hz, cqspi->sclk); 1160 1161 tshsl = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tshsl_ns); 1162 /* this particular value must be at least one sclk */ 1163 if (tshsl < tsclk) 1164 tshsl = tsclk; 1165 1166 tchsh = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tchsh_ns); 1167 tslch = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tslch_ns); 1168 tsd2d = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tsd2d_ns); 1169 1170 reg = (tshsl & CQSPI_REG_DELAY_TSHSL_MASK) 1171 << CQSPI_REG_DELAY_TSHSL_LSB; 1172 reg |= (tchsh & CQSPI_REG_DELAY_TCHSH_MASK) 1173 << CQSPI_REG_DELAY_TCHSH_LSB; 1174 reg |= (tslch & CQSPI_REG_DELAY_TSLCH_MASK) 1175 << CQSPI_REG_DELAY_TSLCH_LSB; 1176 reg |= (tsd2d & CQSPI_REG_DELAY_TSD2D_MASK) 1177 << CQSPI_REG_DELAY_TSD2D_LSB; 1178 writel(reg, iobase + CQSPI_REG_DELAY); 1179 } 1180 1181 static void cqspi_config_baudrate_div(struct cqspi_st *cqspi) 1182 { 1183 const unsigned int ref_clk_hz = cqspi->master_ref_clk_hz; 1184 void __iomem *reg_base = cqspi->iobase; 1185 u32 reg, div; 1186 1187 /* Recalculate the baudrate divisor based on QSPI specification. */ 1188 div = DIV_ROUND_UP(ref_clk_hz, 2 * cqspi->sclk) - 1; 1189 1190 /* Maximum baud divisor */ 1191 if (div > CQSPI_REG_CONFIG_BAUD_MASK) { 1192 div = CQSPI_REG_CONFIG_BAUD_MASK; 1193 dev_warn(&cqspi->pdev->dev, 1194 "Unable to adjust clock <= %d hz. Reduced to %d hz\n", 1195 cqspi->sclk, ref_clk_hz/((div+1)*2)); 1196 } 1197 1198 reg = readl(reg_base + CQSPI_REG_CONFIG); 1199 reg &= ~(CQSPI_REG_CONFIG_BAUD_MASK << CQSPI_REG_CONFIG_BAUD_LSB); 1200 reg |= (div & CQSPI_REG_CONFIG_BAUD_MASK) << CQSPI_REG_CONFIG_BAUD_LSB; 1201 writel(reg, reg_base + CQSPI_REG_CONFIG); 1202 } 1203 1204 static void cqspi_readdata_capture(struct cqspi_st *cqspi, 1205 const bool bypass, 1206 const unsigned int delay) 1207 { 1208 void __iomem *reg_base = cqspi->iobase; 1209 unsigned int reg; 1210 1211 reg = readl(reg_base + CQSPI_REG_READCAPTURE); 1212 1213 if (bypass) 1214 reg |= (1 << CQSPI_REG_READCAPTURE_BYPASS_LSB); 1215 else 1216 reg &= ~(1 << CQSPI_REG_READCAPTURE_BYPASS_LSB); 1217 1218 reg &= ~(CQSPI_REG_READCAPTURE_DELAY_MASK 1219 << CQSPI_REG_READCAPTURE_DELAY_LSB); 1220 1221 reg |= (delay & CQSPI_REG_READCAPTURE_DELAY_MASK) 1222 << CQSPI_REG_READCAPTURE_DELAY_LSB; 1223 1224 writel(reg, reg_base + CQSPI_REG_READCAPTURE); 1225 } 1226 1227 static void cqspi_configure(struct cqspi_flash_pdata *f_pdata, 1228 unsigned long sclk) 1229 { 1230 struct cqspi_st *cqspi = f_pdata->cqspi; 1231 int switch_cs = (cqspi->current_cs != f_pdata->cs); 1232 int switch_ck = (cqspi->sclk != sclk); 1233 1234 if (switch_cs || switch_ck) 1235 cqspi_controller_enable(cqspi, 0); 1236 1237 /* Switch chip select. */ 1238 if (switch_cs) { 1239 cqspi->current_cs = f_pdata->cs; 1240 cqspi_chipselect(f_pdata); 1241 } 1242 1243 /* Setup baudrate divisor and delays */ 1244 if (switch_ck) { 1245 cqspi->sclk = sclk; 1246 cqspi_config_baudrate_div(cqspi); 1247 cqspi_delay(f_pdata); 1248 cqspi_readdata_capture(cqspi, !cqspi->rclk_en, 1249 f_pdata->read_delay); 1250 } 1251 1252 if (switch_cs || switch_ck) 1253 cqspi_controller_enable(cqspi, 1); 1254 } 1255 1256 static ssize_t cqspi_write(struct cqspi_flash_pdata *f_pdata, 1257 const struct spi_mem_op *op) 1258 { 1259 struct cqspi_st *cqspi = f_pdata->cqspi; 1260 loff_t to = op->addr.val; 1261 size_t len = op->data.nbytes; 1262 const u_char *buf = op->data.buf.out; 1263 int ret; 1264 1265 ret = cqspi_write_setup(f_pdata, op); 1266 if (ret) 1267 return ret; 1268 1269 /* 1270 * Some flashes like the Cypress Semper flash expect a dummy 4-byte 1271 * address (all 0s) with the read status register command in DTR mode. 1272 * But this controller does not support sending dummy address bytes to 1273 * the flash when it is polling the write completion register in DTR 1274 * mode. So, we can not use direct mode when in DTR mode for writing 1275 * data. 1276 */ 1277 if (!op->cmd.dtr && cqspi->use_direct_mode && 1278 cqspi->use_direct_mode_wr && ((to + len) <= cqspi->ahb_size)) { 1279 memcpy_toio(cqspi->ahb_base + to, buf, len); 1280 return cqspi_wait_idle(cqspi); 1281 } 1282 1283 return cqspi_indirect_write_execute(f_pdata, to, buf, len); 1284 } 1285 1286 static void cqspi_rx_dma_callback(void *param) 1287 { 1288 struct cqspi_st *cqspi = param; 1289 1290 complete(&cqspi->rx_dma_complete); 1291 } 1292 1293 static int cqspi_direct_read_execute(struct cqspi_flash_pdata *f_pdata, 1294 u_char *buf, loff_t from, size_t len) 1295 { 1296 struct cqspi_st *cqspi = f_pdata->cqspi; 1297 struct device *dev = &cqspi->pdev->dev; 1298 enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT; 1299 dma_addr_t dma_src = (dma_addr_t)cqspi->mmap_phys_base + from; 1300 int ret = 0; 1301 struct dma_async_tx_descriptor *tx; 1302 dma_cookie_t cookie; 1303 dma_addr_t dma_dst; 1304 struct device *ddev; 1305 1306 if (!cqspi->rx_chan || !virt_addr_valid(buf)) { 1307 memcpy_fromio(buf, cqspi->ahb_base + from, len); 1308 return 0; 1309 } 1310 1311 ddev = cqspi->rx_chan->device->dev; 1312 dma_dst = dma_map_single(ddev, buf, len, DMA_FROM_DEVICE); 1313 if (dma_mapping_error(ddev, dma_dst)) { 1314 dev_err(dev, "dma mapping failed\n"); 1315 return -ENOMEM; 1316 } 1317 tx = dmaengine_prep_dma_memcpy(cqspi->rx_chan, dma_dst, dma_src, 1318 len, flags); 1319 if (!tx) { 1320 dev_err(dev, "device_prep_dma_memcpy error\n"); 1321 ret = -EIO; 1322 goto err_unmap; 1323 } 1324 1325 tx->callback = cqspi_rx_dma_callback; 1326 tx->callback_param = cqspi; 1327 cookie = tx->tx_submit(tx); 1328 reinit_completion(&cqspi->rx_dma_complete); 1329 1330 ret = dma_submit_error(cookie); 1331 if (ret) { 1332 dev_err(dev, "dma_submit_error %d\n", cookie); 1333 ret = -EIO; 1334 goto err_unmap; 1335 } 1336 1337 dma_async_issue_pending(cqspi->rx_chan); 1338 if (!wait_for_completion_timeout(&cqspi->rx_dma_complete, 1339 msecs_to_jiffies(max_t(size_t, len, 500)))) { 1340 dmaengine_terminate_sync(cqspi->rx_chan); 1341 dev_err(dev, "DMA wait_for_completion_timeout\n"); 1342 ret = -ETIMEDOUT; 1343 goto err_unmap; 1344 } 1345 1346 err_unmap: 1347 dma_unmap_single(ddev, dma_dst, len, DMA_FROM_DEVICE); 1348 1349 return ret; 1350 } 1351 1352 static ssize_t cqspi_read(struct cqspi_flash_pdata *f_pdata, 1353 const struct spi_mem_op *op) 1354 { 1355 struct cqspi_st *cqspi = f_pdata->cqspi; 1356 struct device *dev = &cqspi->pdev->dev; 1357 const struct cqspi_driver_platdata *ddata; 1358 loff_t from = op->addr.val; 1359 size_t len = op->data.nbytes; 1360 u_char *buf = op->data.buf.in; 1361 u64 dma_align = (u64)(uintptr_t)buf; 1362 int ret; 1363 1364 ddata = of_device_get_match_data(dev); 1365 1366 ret = cqspi_read_setup(f_pdata, op); 1367 if (ret) 1368 return ret; 1369 1370 if (cqspi->use_direct_mode && ((from + len) <= cqspi->ahb_size)) 1371 return cqspi_direct_read_execute(f_pdata, buf, from, len); 1372 1373 if (cqspi->use_dma_read && ddata && ddata->indirect_read_dma && 1374 virt_addr_valid(buf) && ((dma_align & CQSPI_DMA_UNALIGN) == 0)) 1375 return ddata->indirect_read_dma(f_pdata, buf, from, len); 1376 1377 return cqspi_indirect_read_execute(f_pdata, buf, from, len); 1378 } 1379 1380 static int cqspi_mem_process(struct spi_mem *mem, const struct spi_mem_op *op) 1381 { 1382 struct cqspi_st *cqspi = spi_controller_get_devdata(mem->spi->controller); 1383 struct cqspi_flash_pdata *f_pdata; 1384 1385 f_pdata = &cqspi->f_pdata[spi_get_chipselect(mem->spi, 0)]; 1386 cqspi_configure(f_pdata, mem->spi->max_speed_hz); 1387 1388 if (op->data.dir == SPI_MEM_DATA_IN && op->data.buf.in) { 1389 /* 1390 * Performing reads in DAC mode forces to read minimum 4 bytes 1391 * which is unsupported on some flash devices during register 1392 * reads, prefer STIG mode for such small reads. 1393 */ 1394 if (!op->addr.nbytes || 1395 op->data.nbytes <= CQSPI_STIG_DATA_LEN_MAX) 1396 return cqspi_command_read(f_pdata, op); 1397 1398 return cqspi_read(f_pdata, op); 1399 } 1400 1401 if (!op->addr.nbytes || !op->data.buf.out) 1402 return cqspi_command_write(f_pdata, op); 1403 1404 return cqspi_write(f_pdata, op); 1405 } 1406 1407 static int cqspi_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op) 1408 { 1409 int ret; 1410 1411 ret = cqspi_mem_process(mem, op); 1412 if (ret) 1413 dev_err(&mem->spi->dev, "operation failed with %d\n", ret); 1414 1415 return ret; 1416 } 1417 1418 static bool cqspi_supports_mem_op(struct spi_mem *mem, 1419 const struct spi_mem_op *op) 1420 { 1421 bool all_true, all_false; 1422 1423 /* 1424 * op->dummy.dtr is required for converting nbytes into ncycles. 1425 * Also, don't check the dtr field of the op phase having zero nbytes. 1426 */ 1427 all_true = op->cmd.dtr && 1428 (!op->addr.nbytes || op->addr.dtr) && 1429 (!op->dummy.nbytes || op->dummy.dtr) && 1430 (!op->data.nbytes || op->data.dtr); 1431 1432 all_false = !op->cmd.dtr && !op->addr.dtr && !op->dummy.dtr && 1433 !op->data.dtr; 1434 1435 if (all_true) { 1436 /* Right now we only support 8-8-8 DTR mode. */ 1437 if (op->cmd.nbytes && op->cmd.buswidth != 8) 1438 return false; 1439 if (op->addr.nbytes && op->addr.buswidth != 8) 1440 return false; 1441 if (op->data.nbytes && op->data.buswidth != 8) 1442 return false; 1443 } else if (!all_false) { 1444 /* Mixed DTR modes are not supported. */ 1445 return false; 1446 } 1447 1448 return spi_mem_default_supports_op(mem, op); 1449 } 1450 1451 static int cqspi_of_get_flash_pdata(struct platform_device *pdev, 1452 struct cqspi_flash_pdata *f_pdata, 1453 struct device_node *np) 1454 { 1455 if (of_property_read_u32(np, "cdns,read-delay", &f_pdata->read_delay)) { 1456 dev_err(&pdev->dev, "couldn't determine read-delay\n"); 1457 return -ENXIO; 1458 } 1459 1460 if (of_property_read_u32(np, "cdns,tshsl-ns", &f_pdata->tshsl_ns)) { 1461 dev_err(&pdev->dev, "couldn't determine tshsl-ns\n"); 1462 return -ENXIO; 1463 } 1464 1465 if (of_property_read_u32(np, "cdns,tsd2d-ns", &f_pdata->tsd2d_ns)) { 1466 dev_err(&pdev->dev, "couldn't determine tsd2d-ns\n"); 1467 return -ENXIO; 1468 } 1469 1470 if (of_property_read_u32(np, "cdns,tchsh-ns", &f_pdata->tchsh_ns)) { 1471 dev_err(&pdev->dev, "couldn't determine tchsh-ns\n"); 1472 return -ENXIO; 1473 } 1474 1475 if (of_property_read_u32(np, "cdns,tslch-ns", &f_pdata->tslch_ns)) { 1476 dev_err(&pdev->dev, "couldn't determine tslch-ns\n"); 1477 return -ENXIO; 1478 } 1479 1480 if (of_property_read_u32(np, "spi-max-frequency", &f_pdata->clk_rate)) { 1481 dev_err(&pdev->dev, "couldn't determine spi-max-frequency\n"); 1482 return -ENXIO; 1483 } 1484 1485 return 0; 1486 } 1487 1488 static int cqspi_of_get_pdata(struct cqspi_st *cqspi) 1489 { 1490 struct device *dev = &cqspi->pdev->dev; 1491 struct device_node *np = dev->of_node; 1492 u32 id[2]; 1493 1494 cqspi->is_decoded_cs = of_property_read_bool(np, "cdns,is-decoded-cs"); 1495 1496 if (of_property_read_u32(np, "cdns,fifo-depth", &cqspi->fifo_depth)) { 1497 dev_err(dev, "couldn't determine fifo-depth\n"); 1498 return -ENXIO; 1499 } 1500 1501 if (of_property_read_u32(np, "cdns,fifo-width", &cqspi->fifo_width)) { 1502 dev_err(dev, "couldn't determine fifo-width\n"); 1503 return -ENXIO; 1504 } 1505 1506 if (of_property_read_u32(np, "cdns,trigger-address", 1507 &cqspi->trigger_address)) { 1508 dev_err(dev, "couldn't determine trigger-address\n"); 1509 return -ENXIO; 1510 } 1511 1512 if (of_property_read_u32(np, "num-cs", &cqspi->num_chipselect)) 1513 cqspi->num_chipselect = CQSPI_MAX_CHIPSELECT; 1514 1515 cqspi->rclk_en = of_property_read_bool(np, "cdns,rclk-en"); 1516 1517 if (!of_property_read_u32_array(np, "power-domains", id, 1518 ARRAY_SIZE(id))) 1519 cqspi->pd_dev_id = id[1]; 1520 1521 return 0; 1522 } 1523 1524 static void cqspi_controller_init(struct cqspi_st *cqspi) 1525 { 1526 u32 reg; 1527 1528 cqspi_controller_enable(cqspi, 0); 1529 1530 /* Configure the remap address register, no remap */ 1531 writel(0, cqspi->iobase + CQSPI_REG_REMAP); 1532 1533 /* Disable all interrupts. */ 1534 writel(0, cqspi->iobase + CQSPI_REG_IRQMASK); 1535 1536 /* Configure the SRAM split to 1:1 . */ 1537 writel(cqspi->fifo_depth / 2, cqspi->iobase + CQSPI_REG_SRAMPARTITION); 1538 1539 /* Load indirect trigger address. */ 1540 writel(cqspi->trigger_address, 1541 cqspi->iobase + CQSPI_REG_INDIRECTTRIGGER); 1542 1543 /* Program read watermark -- 1/2 of the FIFO. */ 1544 writel(cqspi->fifo_depth * cqspi->fifo_width / 2, 1545 cqspi->iobase + CQSPI_REG_INDIRECTRDWATERMARK); 1546 /* Program write watermark -- 1/8 of the FIFO. */ 1547 writel(cqspi->fifo_depth * cqspi->fifo_width / 8, 1548 cqspi->iobase + CQSPI_REG_INDIRECTWRWATERMARK); 1549 1550 /* Disable direct access controller */ 1551 if (!cqspi->use_direct_mode) { 1552 reg = readl(cqspi->iobase + CQSPI_REG_CONFIG); 1553 reg &= ~CQSPI_REG_CONFIG_ENB_DIR_ACC_CTRL; 1554 writel(reg, cqspi->iobase + CQSPI_REG_CONFIG); 1555 } 1556 1557 /* Enable DMA interface */ 1558 if (cqspi->use_dma_read) { 1559 reg = readl(cqspi->iobase + CQSPI_REG_CONFIG); 1560 reg |= CQSPI_REG_CONFIG_DMA_MASK; 1561 writel(reg, cqspi->iobase + CQSPI_REG_CONFIG); 1562 } 1563 1564 cqspi_controller_enable(cqspi, 1); 1565 } 1566 1567 static int cqspi_request_mmap_dma(struct cqspi_st *cqspi) 1568 { 1569 dma_cap_mask_t mask; 1570 1571 dma_cap_zero(mask); 1572 dma_cap_set(DMA_MEMCPY, mask); 1573 1574 cqspi->rx_chan = dma_request_chan_by_mask(&mask); 1575 if (IS_ERR(cqspi->rx_chan)) { 1576 int ret = PTR_ERR(cqspi->rx_chan); 1577 1578 cqspi->rx_chan = NULL; 1579 return dev_err_probe(&cqspi->pdev->dev, ret, "No Rx DMA available\n"); 1580 } 1581 init_completion(&cqspi->rx_dma_complete); 1582 1583 return 0; 1584 } 1585 1586 static const char *cqspi_get_name(struct spi_mem *mem) 1587 { 1588 struct cqspi_st *cqspi = spi_controller_get_devdata(mem->spi->controller); 1589 struct device *dev = &cqspi->pdev->dev; 1590 1591 return devm_kasprintf(dev, GFP_KERNEL, "%s.%d", dev_name(dev), 1592 spi_get_chipselect(mem->spi, 0)); 1593 } 1594 1595 static const struct spi_controller_mem_ops cqspi_mem_ops = { 1596 .exec_op = cqspi_exec_mem_op, 1597 .get_name = cqspi_get_name, 1598 .supports_op = cqspi_supports_mem_op, 1599 }; 1600 1601 static const struct spi_controller_mem_caps cqspi_mem_caps = { 1602 .dtr = true, 1603 }; 1604 1605 static int cqspi_setup_flash(struct cqspi_st *cqspi) 1606 { 1607 struct platform_device *pdev = cqspi->pdev; 1608 struct device *dev = &pdev->dev; 1609 struct device_node *np = dev->of_node; 1610 struct cqspi_flash_pdata *f_pdata; 1611 unsigned int cs; 1612 int ret; 1613 1614 /* Get flash device data */ 1615 for_each_available_child_of_node(dev->of_node, np) { 1616 ret = of_property_read_u32(np, "reg", &cs); 1617 if (ret) { 1618 dev_err(dev, "Couldn't determine chip select.\n"); 1619 of_node_put(np); 1620 return ret; 1621 } 1622 1623 if (cs >= CQSPI_MAX_CHIPSELECT) { 1624 dev_err(dev, "Chip select %d out of range.\n", cs); 1625 of_node_put(np); 1626 return -EINVAL; 1627 } 1628 1629 f_pdata = &cqspi->f_pdata[cs]; 1630 f_pdata->cqspi = cqspi; 1631 f_pdata->cs = cs; 1632 1633 ret = cqspi_of_get_flash_pdata(pdev, f_pdata, np); 1634 if (ret) { 1635 of_node_put(np); 1636 return ret; 1637 } 1638 } 1639 1640 return 0; 1641 } 1642 1643 static int cqspi_jh7110_clk_init(struct platform_device *pdev, struct cqspi_st *cqspi) 1644 { 1645 static struct clk_bulk_data qspiclk[] = { 1646 { .id = "apb" }, 1647 { .id = "ahb" }, 1648 }; 1649 1650 int ret = 0; 1651 1652 ret = devm_clk_bulk_get(&pdev->dev, ARRAY_SIZE(qspiclk), qspiclk); 1653 if (ret) { 1654 dev_err(&pdev->dev, "%s: failed to get qspi clocks\n", __func__); 1655 return ret; 1656 } 1657 1658 cqspi->clks[CLK_QSPI_APB] = qspiclk[0].clk; 1659 cqspi->clks[CLK_QSPI_AHB] = qspiclk[1].clk; 1660 1661 ret = clk_prepare_enable(cqspi->clks[CLK_QSPI_APB]); 1662 if (ret) { 1663 dev_err(&pdev->dev, "%s: failed to enable CLK_QSPI_APB\n", __func__); 1664 return ret; 1665 } 1666 1667 ret = clk_prepare_enable(cqspi->clks[CLK_QSPI_AHB]); 1668 if (ret) { 1669 dev_err(&pdev->dev, "%s: failed to enable CLK_QSPI_AHB\n", __func__); 1670 goto disable_apb_clk; 1671 } 1672 1673 cqspi->is_jh7110 = true; 1674 1675 return 0; 1676 1677 disable_apb_clk: 1678 clk_disable_unprepare(cqspi->clks[CLK_QSPI_APB]); 1679 1680 return ret; 1681 } 1682 1683 static void cqspi_jh7110_disable_clk(struct platform_device *pdev, struct cqspi_st *cqspi) 1684 { 1685 clk_disable_unprepare(cqspi->clks[CLK_QSPI_AHB]); 1686 clk_disable_unprepare(cqspi->clks[CLK_QSPI_APB]); 1687 } 1688 static int cqspi_probe(struct platform_device *pdev) 1689 { 1690 const struct cqspi_driver_platdata *ddata; 1691 struct reset_control *rstc, *rstc_ocp, *rstc_ref; 1692 struct device *dev = &pdev->dev; 1693 struct spi_controller *host; 1694 struct resource *res_ahb; 1695 struct cqspi_st *cqspi; 1696 int ret; 1697 int irq; 1698 1699 host = devm_spi_alloc_host(&pdev->dev, sizeof(*cqspi)); 1700 if (!host) { 1701 dev_err(&pdev->dev, "devm_spi_alloc_host failed\n"); 1702 return -ENOMEM; 1703 } 1704 host->mode_bits = SPI_RX_QUAD | SPI_RX_DUAL; 1705 host->mem_ops = &cqspi_mem_ops; 1706 host->mem_caps = &cqspi_mem_caps; 1707 host->dev.of_node = pdev->dev.of_node; 1708 1709 cqspi = spi_controller_get_devdata(host); 1710 1711 cqspi->pdev = pdev; 1712 cqspi->host = host; 1713 cqspi->is_jh7110 = false; 1714 platform_set_drvdata(pdev, cqspi); 1715 1716 /* Obtain configuration from OF. */ 1717 ret = cqspi_of_get_pdata(cqspi); 1718 if (ret) { 1719 dev_err(dev, "Cannot get mandatory OF data.\n"); 1720 return -ENODEV; 1721 } 1722 1723 /* Obtain QSPI clock. */ 1724 cqspi->clk = devm_clk_get(dev, NULL); 1725 if (IS_ERR(cqspi->clk)) { 1726 dev_err(dev, "Cannot claim QSPI clock.\n"); 1727 ret = PTR_ERR(cqspi->clk); 1728 return ret; 1729 } 1730 1731 /* Obtain and remap controller address. */ 1732 cqspi->iobase = devm_platform_ioremap_resource(pdev, 0); 1733 if (IS_ERR(cqspi->iobase)) { 1734 dev_err(dev, "Cannot remap controller address.\n"); 1735 ret = PTR_ERR(cqspi->iobase); 1736 return ret; 1737 } 1738 1739 /* Obtain and remap AHB address. */ 1740 cqspi->ahb_base = devm_platform_get_and_ioremap_resource(pdev, 1, &res_ahb); 1741 if (IS_ERR(cqspi->ahb_base)) { 1742 dev_err(dev, "Cannot remap AHB address.\n"); 1743 ret = PTR_ERR(cqspi->ahb_base); 1744 return ret; 1745 } 1746 cqspi->mmap_phys_base = (dma_addr_t)res_ahb->start; 1747 cqspi->ahb_size = resource_size(res_ahb); 1748 1749 init_completion(&cqspi->transfer_complete); 1750 1751 /* Obtain IRQ line. */ 1752 irq = platform_get_irq(pdev, 0); 1753 if (irq < 0) 1754 return -ENXIO; 1755 1756 pm_runtime_enable(dev); 1757 ret = pm_runtime_resume_and_get(dev); 1758 if (ret < 0) 1759 goto probe_pm_failed; 1760 1761 ret = clk_prepare_enable(cqspi->clk); 1762 if (ret) { 1763 dev_err(dev, "Cannot enable QSPI clock.\n"); 1764 goto probe_clk_failed; 1765 } 1766 1767 /* Obtain QSPI reset control */ 1768 rstc = devm_reset_control_get_optional_exclusive(dev, "qspi"); 1769 if (IS_ERR(rstc)) { 1770 ret = PTR_ERR(rstc); 1771 dev_err(dev, "Cannot get QSPI reset.\n"); 1772 goto probe_reset_failed; 1773 } 1774 1775 rstc_ocp = devm_reset_control_get_optional_exclusive(dev, "qspi-ocp"); 1776 if (IS_ERR(rstc_ocp)) { 1777 ret = PTR_ERR(rstc_ocp); 1778 dev_err(dev, "Cannot get QSPI OCP reset.\n"); 1779 goto probe_reset_failed; 1780 } 1781 1782 if (of_device_is_compatible(pdev->dev.of_node, "starfive,jh7110-qspi")) { 1783 rstc_ref = devm_reset_control_get_optional_exclusive(dev, "rstc_ref"); 1784 if (IS_ERR(rstc_ref)) { 1785 ret = PTR_ERR(rstc_ref); 1786 dev_err(dev, "Cannot get QSPI REF reset.\n"); 1787 goto probe_reset_failed; 1788 } 1789 reset_control_assert(rstc_ref); 1790 reset_control_deassert(rstc_ref); 1791 } 1792 1793 reset_control_assert(rstc); 1794 reset_control_deassert(rstc); 1795 1796 reset_control_assert(rstc_ocp); 1797 reset_control_deassert(rstc_ocp); 1798 1799 cqspi->master_ref_clk_hz = clk_get_rate(cqspi->clk); 1800 host->max_speed_hz = cqspi->master_ref_clk_hz; 1801 1802 /* write completion is supported by default */ 1803 cqspi->wr_completion = true; 1804 1805 ddata = of_device_get_match_data(dev); 1806 if (ddata) { 1807 if (ddata->quirks & CQSPI_NEEDS_WR_DELAY) 1808 cqspi->wr_delay = 50 * DIV_ROUND_UP(NSEC_PER_SEC, 1809 cqspi->master_ref_clk_hz); 1810 if (ddata->hwcaps_mask & CQSPI_SUPPORTS_OCTAL) 1811 host->mode_bits |= SPI_RX_OCTAL | SPI_TX_OCTAL; 1812 if (!(ddata->quirks & CQSPI_DISABLE_DAC_MODE)) { 1813 cqspi->use_direct_mode = true; 1814 cqspi->use_direct_mode_wr = true; 1815 } 1816 if (ddata->quirks & CQSPI_SUPPORT_EXTERNAL_DMA) 1817 cqspi->use_dma_read = true; 1818 if (ddata->quirks & CQSPI_NO_SUPPORT_WR_COMPLETION) 1819 cqspi->wr_completion = false; 1820 if (ddata->quirks & CQSPI_SLOW_SRAM) 1821 cqspi->slow_sram = true; 1822 if (ddata->quirks & CQSPI_NEEDS_APB_AHB_HAZARD_WAR) 1823 cqspi->apb_ahb_hazard = true; 1824 1825 if (ddata->jh7110_clk_init) { 1826 ret = cqspi_jh7110_clk_init(pdev, cqspi); 1827 if (ret) 1828 goto probe_reset_failed; 1829 } 1830 1831 if (of_device_is_compatible(pdev->dev.of_node, 1832 "xlnx,versal-ospi-1.0")) { 1833 ret = dma_set_mask(&pdev->dev, DMA_BIT_MASK(64)); 1834 if (ret) 1835 goto probe_reset_failed; 1836 } 1837 } 1838 1839 ret = devm_request_irq(dev, irq, cqspi_irq_handler, 0, 1840 pdev->name, cqspi); 1841 if (ret) { 1842 dev_err(dev, "Cannot request IRQ.\n"); 1843 goto probe_reset_failed; 1844 } 1845 1846 cqspi_wait_idle(cqspi); 1847 cqspi_controller_init(cqspi); 1848 cqspi->current_cs = -1; 1849 cqspi->sclk = 0; 1850 1851 host->num_chipselect = cqspi->num_chipselect; 1852 1853 ret = cqspi_setup_flash(cqspi); 1854 if (ret) { 1855 dev_err(dev, "failed to setup flash parameters %d\n", ret); 1856 goto probe_setup_failed; 1857 } 1858 1859 if (cqspi->use_direct_mode) { 1860 ret = cqspi_request_mmap_dma(cqspi); 1861 if (ret == -EPROBE_DEFER) 1862 goto probe_setup_failed; 1863 } 1864 1865 ret = spi_register_controller(host); 1866 if (ret) { 1867 dev_err(&pdev->dev, "failed to register SPI ctlr %d\n", ret); 1868 goto probe_setup_failed; 1869 } 1870 1871 return 0; 1872 probe_setup_failed: 1873 cqspi_controller_enable(cqspi, 0); 1874 probe_reset_failed: 1875 if (cqspi->is_jh7110) 1876 cqspi_jh7110_disable_clk(pdev, cqspi); 1877 clk_disable_unprepare(cqspi->clk); 1878 probe_clk_failed: 1879 pm_runtime_put_sync(dev); 1880 probe_pm_failed: 1881 pm_runtime_disable(dev); 1882 return ret; 1883 } 1884 1885 static void cqspi_remove(struct platform_device *pdev) 1886 { 1887 struct cqspi_st *cqspi = platform_get_drvdata(pdev); 1888 1889 spi_unregister_controller(cqspi->host); 1890 cqspi_controller_enable(cqspi, 0); 1891 1892 if (cqspi->rx_chan) 1893 dma_release_channel(cqspi->rx_chan); 1894 1895 clk_disable_unprepare(cqspi->clk); 1896 1897 if (cqspi->is_jh7110) 1898 cqspi_jh7110_disable_clk(pdev, cqspi); 1899 1900 pm_runtime_put_sync(&pdev->dev); 1901 pm_runtime_disable(&pdev->dev); 1902 } 1903 1904 static int cqspi_suspend(struct device *dev) 1905 { 1906 struct cqspi_st *cqspi = dev_get_drvdata(dev); 1907 int ret; 1908 1909 ret = spi_controller_suspend(cqspi->host); 1910 cqspi_controller_enable(cqspi, 0); 1911 1912 clk_disable_unprepare(cqspi->clk); 1913 1914 return ret; 1915 } 1916 1917 static int cqspi_resume(struct device *dev) 1918 { 1919 struct cqspi_st *cqspi = dev_get_drvdata(dev); 1920 1921 clk_prepare_enable(cqspi->clk); 1922 cqspi_wait_idle(cqspi); 1923 cqspi_controller_init(cqspi); 1924 1925 cqspi->current_cs = -1; 1926 cqspi->sclk = 0; 1927 1928 return spi_controller_resume(cqspi->host); 1929 } 1930 1931 static DEFINE_SIMPLE_DEV_PM_OPS(cqspi_dev_pm_ops, cqspi_suspend, cqspi_resume); 1932 1933 static const struct cqspi_driver_platdata cdns_qspi = { 1934 .quirks = CQSPI_DISABLE_DAC_MODE, 1935 }; 1936 1937 static const struct cqspi_driver_platdata k2g_qspi = { 1938 .quirks = CQSPI_NEEDS_WR_DELAY, 1939 }; 1940 1941 static const struct cqspi_driver_platdata am654_ospi = { 1942 .hwcaps_mask = CQSPI_SUPPORTS_OCTAL, 1943 .quirks = CQSPI_NEEDS_WR_DELAY, 1944 }; 1945 1946 static const struct cqspi_driver_platdata intel_lgm_qspi = { 1947 .quirks = CQSPI_DISABLE_DAC_MODE, 1948 }; 1949 1950 static const struct cqspi_driver_platdata socfpga_qspi = { 1951 .quirks = CQSPI_DISABLE_DAC_MODE 1952 | CQSPI_NO_SUPPORT_WR_COMPLETION 1953 | CQSPI_SLOW_SRAM, 1954 }; 1955 1956 static const struct cqspi_driver_platdata versal_ospi = { 1957 .hwcaps_mask = CQSPI_SUPPORTS_OCTAL, 1958 .quirks = CQSPI_DISABLE_DAC_MODE | CQSPI_SUPPORT_EXTERNAL_DMA, 1959 .indirect_read_dma = cqspi_versal_indirect_read_dma, 1960 .get_dma_status = cqspi_get_versal_dma_status, 1961 }; 1962 1963 static const struct cqspi_driver_platdata jh7110_qspi = { 1964 .quirks = CQSPI_DISABLE_DAC_MODE, 1965 .jh7110_clk_init = cqspi_jh7110_clk_init, 1966 }; 1967 1968 static const struct cqspi_driver_platdata pensando_cdns_qspi = { 1969 .quirks = CQSPI_NEEDS_APB_AHB_HAZARD_WAR | CQSPI_DISABLE_DAC_MODE, 1970 }; 1971 1972 static const struct of_device_id cqspi_dt_ids[] = { 1973 { 1974 .compatible = "cdns,qspi-nor", 1975 .data = &cdns_qspi, 1976 }, 1977 { 1978 .compatible = "ti,k2g-qspi", 1979 .data = &k2g_qspi, 1980 }, 1981 { 1982 .compatible = "ti,am654-ospi", 1983 .data = &am654_ospi, 1984 }, 1985 { 1986 .compatible = "intel,lgm-qspi", 1987 .data = &intel_lgm_qspi, 1988 }, 1989 { 1990 .compatible = "xlnx,versal-ospi-1.0", 1991 .data = &versal_ospi, 1992 }, 1993 { 1994 .compatible = "intel,socfpga-qspi", 1995 .data = &socfpga_qspi, 1996 }, 1997 { 1998 .compatible = "starfive,jh7110-qspi", 1999 .data = &jh7110_qspi, 2000 }, 2001 { 2002 .compatible = "amd,pensando-elba-qspi", 2003 .data = &pensando_cdns_qspi, 2004 }, 2005 { /* end of table */ } 2006 }; 2007 2008 MODULE_DEVICE_TABLE(of, cqspi_dt_ids); 2009 2010 static struct platform_driver cqspi_platform_driver = { 2011 .probe = cqspi_probe, 2012 .remove_new = cqspi_remove, 2013 .driver = { 2014 .name = CQSPI_NAME, 2015 .pm = &cqspi_dev_pm_ops, 2016 .of_match_table = cqspi_dt_ids, 2017 }, 2018 }; 2019 2020 module_platform_driver(cqspi_platform_driver); 2021 2022 MODULE_DESCRIPTION("Cadence QSPI Controller Driver"); 2023 MODULE_LICENSE("GPL v2"); 2024 MODULE_ALIAS("platform:" CQSPI_NAME); 2025 MODULE_AUTHOR("Ley Foon Tan <lftan@altera.com>"); 2026 MODULE_AUTHOR("Graham Moore <grmoore@opensource.altera.com>"); 2027 MODULE_AUTHOR("Vadivel Murugan R <vadivel.muruganx.ramuthevar@intel.com>"); 2028 MODULE_AUTHOR("Vignesh Raghavendra <vigneshr@ti.com>"); 2029 MODULE_AUTHOR("Pratyush Yadav <p.yadav@ti.com>"); 2030