1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Driver for Broadcom BCM2835 auxiliary SPI Controllers 4 * 5 * the driver does not rely on the native chipselects at all 6 * but only uses the gpio type chipselects 7 * 8 * Based on: spi-bcm2835.c 9 * 10 * Copyright (C) 2015 Martin Sperl 11 */ 12 13 #include <linux/clk.h> 14 #include <linux/completion.h> 15 #include <linux/debugfs.h> 16 #include <linux/delay.h> 17 #include <linux/err.h> 18 #include <linux/interrupt.h> 19 #include <linux/io.h> 20 #include <linux/kernel.h> 21 #include <linux/module.h> 22 #include <linux/of.h> 23 #include <linux/of_address.h> 24 #include <linux/of_device.h> 25 #include <linux/of_gpio.h> 26 #include <linux/of_irq.h> 27 #include <linux/regmap.h> 28 #include <linux/spi/spi.h> 29 #include <linux/spinlock.h> 30 31 /* define polling limits */ 32 static unsigned int polling_limit_us = 30; 33 module_param(polling_limit_us, uint, 0664); 34 MODULE_PARM_DESC(polling_limit_us, 35 "time in us to run a transfer in polling mode - if zero no polling is used\n"); 36 37 /* 38 * spi register defines 39 * 40 * note there is garbage in the "official" documentation, 41 * so some data is taken from the file: 42 * brcm_usrlib/dag/vmcsx/vcinclude/bcm2708_chip/aux_io.h 43 * inside of: 44 * http://www.broadcom.com/docs/support/videocore/Brcm_Android_ICS_Graphics_Stack.tar.gz 45 */ 46 47 /* SPI register offsets */ 48 #define BCM2835_AUX_SPI_CNTL0 0x00 49 #define BCM2835_AUX_SPI_CNTL1 0x04 50 #define BCM2835_AUX_SPI_STAT 0x08 51 #define BCM2835_AUX_SPI_PEEK 0x0C 52 #define BCM2835_AUX_SPI_IO 0x20 53 #define BCM2835_AUX_SPI_TXHOLD 0x30 54 55 /* Bitfields in CNTL0 */ 56 #define BCM2835_AUX_SPI_CNTL0_SPEED 0xFFF00000 57 #define BCM2835_AUX_SPI_CNTL0_SPEED_MAX 0xFFF 58 #define BCM2835_AUX_SPI_CNTL0_SPEED_SHIFT 20 59 #define BCM2835_AUX_SPI_CNTL0_CS 0x000E0000 60 #define BCM2835_AUX_SPI_CNTL0_POSTINPUT 0x00010000 61 #define BCM2835_AUX_SPI_CNTL0_VAR_CS 0x00008000 62 #define BCM2835_AUX_SPI_CNTL0_VAR_WIDTH 0x00004000 63 #define BCM2835_AUX_SPI_CNTL0_DOUTHOLD 0x00003000 64 #define BCM2835_AUX_SPI_CNTL0_ENABLE 0x00000800 65 #define BCM2835_AUX_SPI_CNTL0_IN_RISING 0x00000400 66 #define BCM2835_AUX_SPI_CNTL0_CLEARFIFO 0x00000200 67 #define BCM2835_AUX_SPI_CNTL0_OUT_RISING 0x00000100 68 #define BCM2835_AUX_SPI_CNTL0_CPOL 0x00000080 69 #define BCM2835_AUX_SPI_CNTL0_MSBF_OUT 0x00000040 70 #define BCM2835_AUX_SPI_CNTL0_SHIFTLEN 0x0000003F 71 72 /* Bitfields in CNTL1 */ 73 #define BCM2835_AUX_SPI_CNTL1_CSHIGH 0x00000700 74 #define BCM2835_AUX_SPI_CNTL1_TXEMPTY 0x00000080 75 #define BCM2835_AUX_SPI_CNTL1_IDLE 0x00000040 76 #define BCM2835_AUX_SPI_CNTL1_MSBF_IN 0x00000002 77 #define BCM2835_AUX_SPI_CNTL1_KEEP_IN 0x00000001 78 79 /* Bitfields in STAT */ 80 #define BCM2835_AUX_SPI_STAT_TX_LVL 0xFF000000 81 #define BCM2835_AUX_SPI_STAT_RX_LVL 0x00FF0000 82 #define BCM2835_AUX_SPI_STAT_TX_FULL 0x00000400 83 #define BCM2835_AUX_SPI_STAT_TX_EMPTY 0x00000200 84 #define BCM2835_AUX_SPI_STAT_RX_FULL 0x00000100 85 #define BCM2835_AUX_SPI_STAT_RX_EMPTY 0x00000080 86 #define BCM2835_AUX_SPI_STAT_BUSY 0x00000040 87 #define BCM2835_AUX_SPI_STAT_BITCOUNT 0x0000003F 88 89 struct bcm2835aux_spi { 90 void __iomem *regs; 91 struct clk *clk; 92 int irq; 93 u32 cntl[2]; 94 const u8 *tx_buf; 95 u8 *rx_buf; 96 int tx_len; 97 int rx_len; 98 int pending; 99 100 u64 count_transfer_polling; 101 u64 count_transfer_irq; 102 u64 count_transfer_irq_after_poll; 103 104 struct dentry *debugfs_dir; 105 }; 106 107 #if defined(CONFIG_DEBUG_FS) 108 static void bcm2835aux_debugfs_create(struct bcm2835aux_spi *bs, 109 const char *dname) 110 { 111 char name[64]; 112 struct dentry *dir; 113 114 /* get full name */ 115 snprintf(name, sizeof(name), "spi-bcm2835aux-%s", dname); 116 117 /* the base directory */ 118 dir = debugfs_create_dir(name, NULL); 119 bs->debugfs_dir = dir; 120 121 /* the counters */ 122 debugfs_create_u64("count_transfer_polling", 0444, dir, 123 &bs->count_transfer_polling); 124 debugfs_create_u64("count_transfer_irq", 0444, dir, 125 &bs->count_transfer_irq); 126 debugfs_create_u64("count_transfer_irq_after_poll", 0444, dir, 127 &bs->count_transfer_irq_after_poll); 128 } 129 130 static void bcm2835aux_debugfs_remove(struct bcm2835aux_spi *bs) 131 { 132 debugfs_remove_recursive(bs->debugfs_dir); 133 bs->debugfs_dir = NULL; 134 } 135 #else 136 static void bcm2835aux_debugfs_create(struct bcm2835aux_spi *bs, 137 const char *dname) 138 { 139 } 140 141 static void bcm2835aux_debugfs_remove(struct bcm2835aux_spi *bs) 142 { 143 } 144 #endif /* CONFIG_DEBUG_FS */ 145 146 static inline u32 bcm2835aux_rd(struct bcm2835aux_spi *bs, unsigned reg) 147 { 148 return readl(bs->regs + reg); 149 } 150 151 static inline void bcm2835aux_wr(struct bcm2835aux_spi *bs, unsigned reg, 152 u32 val) 153 { 154 writel(val, bs->regs + reg); 155 } 156 157 static inline void bcm2835aux_rd_fifo(struct bcm2835aux_spi *bs) 158 { 159 u32 data; 160 int count = min(bs->rx_len, 3); 161 162 data = bcm2835aux_rd(bs, BCM2835_AUX_SPI_IO); 163 if (bs->rx_buf) { 164 switch (count) { 165 case 3: 166 *bs->rx_buf++ = (data >> 16) & 0xff; 167 /* fallthrough */ 168 case 2: 169 *bs->rx_buf++ = (data >> 8) & 0xff; 170 /* fallthrough */ 171 case 1: 172 *bs->rx_buf++ = (data >> 0) & 0xff; 173 /* fallthrough - no default */ 174 } 175 } 176 bs->rx_len -= count; 177 bs->pending -= count; 178 } 179 180 static inline void bcm2835aux_wr_fifo(struct bcm2835aux_spi *bs) 181 { 182 u32 data; 183 u8 byte; 184 int count; 185 int i; 186 187 /* gather up to 3 bytes to write to the FIFO */ 188 count = min(bs->tx_len, 3); 189 data = 0; 190 for (i = 0; i < count; i++) { 191 byte = bs->tx_buf ? *bs->tx_buf++ : 0; 192 data |= byte << (8 * (2 - i)); 193 } 194 195 /* and set the variable bit-length */ 196 data |= (count * 8) << 24; 197 198 /* and decrement length */ 199 bs->tx_len -= count; 200 bs->pending += count; 201 202 /* write to the correct TX-register */ 203 if (bs->tx_len) 204 bcm2835aux_wr(bs, BCM2835_AUX_SPI_TXHOLD, data); 205 else 206 bcm2835aux_wr(bs, BCM2835_AUX_SPI_IO, data); 207 } 208 209 static void bcm2835aux_spi_reset_hw(struct bcm2835aux_spi *bs) 210 { 211 /* disable spi clearing fifo and interrupts */ 212 bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL1, 0); 213 bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL0, 214 BCM2835_AUX_SPI_CNTL0_CLEARFIFO); 215 } 216 217 static void bcm2835aux_spi_transfer_helper(struct bcm2835aux_spi *bs) 218 { 219 u32 stat = bcm2835aux_rd(bs, BCM2835_AUX_SPI_STAT); 220 221 /* check if we have data to read */ 222 for (; bs->rx_len && (stat & BCM2835_AUX_SPI_STAT_RX_LVL); 223 stat = bcm2835aux_rd(bs, BCM2835_AUX_SPI_STAT)) 224 bcm2835aux_rd_fifo(bs); 225 226 /* check if we have data to write */ 227 while (bs->tx_len && 228 (bs->pending < 12) && 229 (!(bcm2835aux_rd(bs, BCM2835_AUX_SPI_STAT) & 230 BCM2835_AUX_SPI_STAT_TX_FULL))) { 231 bcm2835aux_wr_fifo(bs); 232 } 233 } 234 235 static irqreturn_t bcm2835aux_spi_interrupt(int irq, void *dev_id) 236 { 237 struct spi_master *master = dev_id; 238 struct bcm2835aux_spi *bs = spi_master_get_devdata(master); 239 240 /* IRQ may be shared, so return if our interrupts are disabled */ 241 if (!(bcm2835aux_rd(bs, BCM2835_AUX_SPI_CNTL1) & 242 (BCM2835_AUX_SPI_CNTL1_TXEMPTY | BCM2835_AUX_SPI_CNTL1_IDLE))) 243 return IRQ_NONE; 244 245 /* do common fifo handling */ 246 bcm2835aux_spi_transfer_helper(bs); 247 248 if (!bs->tx_len) { 249 /* disable tx fifo empty interrupt */ 250 bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL1, bs->cntl[1] | 251 BCM2835_AUX_SPI_CNTL1_IDLE); 252 } 253 254 /* and if rx_len is 0 then disable interrupts and wake up completion */ 255 if (!bs->rx_len) { 256 bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL1, bs->cntl[1]); 257 complete(&master->xfer_completion); 258 } 259 260 return IRQ_HANDLED; 261 } 262 263 static int __bcm2835aux_spi_transfer_one_irq(struct spi_master *master, 264 struct spi_device *spi, 265 struct spi_transfer *tfr) 266 { 267 struct bcm2835aux_spi *bs = spi_master_get_devdata(master); 268 269 /* enable interrupts */ 270 bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL1, bs->cntl[1] | 271 BCM2835_AUX_SPI_CNTL1_TXEMPTY | 272 BCM2835_AUX_SPI_CNTL1_IDLE); 273 274 /* and wait for finish... */ 275 return 1; 276 } 277 278 static int bcm2835aux_spi_transfer_one_irq(struct spi_master *master, 279 struct spi_device *spi, 280 struct spi_transfer *tfr) 281 { 282 struct bcm2835aux_spi *bs = spi_master_get_devdata(master); 283 284 /* update statistics */ 285 bs->count_transfer_irq++; 286 287 /* fill in registers and fifos before enabling interrupts */ 288 bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL1, bs->cntl[1]); 289 bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL0, bs->cntl[0]); 290 291 /* fill in tx fifo with data before enabling interrupts */ 292 while ((bs->tx_len) && 293 (bs->pending < 12) && 294 (!(bcm2835aux_rd(bs, BCM2835_AUX_SPI_STAT) & 295 BCM2835_AUX_SPI_STAT_TX_FULL))) { 296 bcm2835aux_wr_fifo(bs); 297 } 298 299 /* now run the interrupt mode */ 300 return __bcm2835aux_spi_transfer_one_irq(master, spi, tfr); 301 } 302 303 static int bcm2835aux_spi_transfer_one_poll(struct spi_master *master, 304 struct spi_device *spi, 305 struct spi_transfer *tfr) 306 { 307 struct bcm2835aux_spi *bs = spi_master_get_devdata(master); 308 unsigned long timeout; 309 310 /* update statistics */ 311 bs->count_transfer_polling++; 312 313 /* configure spi */ 314 bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL1, bs->cntl[1]); 315 bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL0, bs->cntl[0]); 316 317 /* set the timeout to at least 2 jiffies */ 318 timeout = jiffies + 2 + HZ * polling_limit_us / 1000000; 319 320 /* loop until finished the transfer */ 321 while (bs->rx_len) { 322 323 /* do common fifo handling */ 324 bcm2835aux_spi_transfer_helper(bs); 325 326 /* there is still data pending to read check the timeout */ 327 if (bs->rx_len && time_after(jiffies, timeout)) { 328 dev_dbg_ratelimited(&spi->dev, 329 "timeout period reached: jiffies: %lu remaining tx/rx: %d/%d - falling back to interrupt mode\n", 330 jiffies - timeout, 331 bs->tx_len, bs->rx_len); 332 /* forward to interrupt handler */ 333 bs->count_transfer_irq_after_poll++; 334 return __bcm2835aux_spi_transfer_one_irq(master, 335 spi, tfr); 336 } 337 } 338 339 /* and return without waiting for completion */ 340 return 0; 341 } 342 343 static int bcm2835aux_spi_transfer_one(struct spi_master *master, 344 struct spi_device *spi, 345 struct spi_transfer *tfr) 346 { 347 struct bcm2835aux_spi *bs = spi_master_get_devdata(master); 348 unsigned long spi_hz, clk_hz, speed, spi_used_hz; 349 unsigned long hz_per_byte, byte_limit; 350 351 /* calculate the registers to handle 352 * 353 * note that we use the variable data mode, which 354 * is not optimal for longer transfers as we waste registers 355 * resulting (potentially) in more interrupts when transferring 356 * more than 12 bytes 357 */ 358 359 /* set clock */ 360 spi_hz = tfr->speed_hz; 361 clk_hz = clk_get_rate(bs->clk); 362 363 if (spi_hz >= clk_hz / 2) { 364 speed = 0; 365 } else if (spi_hz) { 366 speed = DIV_ROUND_UP(clk_hz, 2 * spi_hz) - 1; 367 if (speed > BCM2835_AUX_SPI_CNTL0_SPEED_MAX) 368 speed = BCM2835_AUX_SPI_CNTL0_SPEED_MAX; 369 } else { /* the slowest we can go */ 370 speed = BCM2835_AUX_SPI_CNTL0_SPEED_MAX; 371 } 372 /* mask out old speed from previous spi_transfer */ 373 bs->cntl[0] &= ~(BCM2835_AUX_SPI_CNTL0_SPEED); 374 /* set the new speed */ 375 bs->cntl[0] |= speed << BCM2835_AUX_SPI_CNTL0_SPEED_SHIFT; 376 377 spi_used_hz = clk_hz / (2 * (speed + 1)); 378 379 /* set transmit buffers and length */ 380 bs->tx_buf = tfr->tx_buf; 381 bs->rx_buf = tfr->rx_buf; 382 bs->tx_len = tfr->len; 383 bs->rx_len = tfr->len; 384 bs->pending = 0; 385 386 /* Calculate the estimated time in us the transfer runs. Note that 387 * there are are 2 idle clocks cycles after each chunk getting 388 * transferred - in our case the chunk size is 3 bytes, so we 389 * approximate this by 9 cycles/byte. This is used to find the number 390 * of Hz per byte per polling limit. E.g., we can transfer 1 byte in 391 * 30 µs per 300,000 Hz of bus clock. 392 */ 393 hz_per_byte = polling_limit_us ? (9 * 1000000) / polling_limit_us : 0; 394 byte_limit = hz_per_byte ? spi_used_hz / hz_per_byte : 1; 395 396 /* run in polling mode for short transfers */ 397 if (tfr->len < byte_limit) 398 return bcm2835aux_spi_transfer_one_poll(master, spi, tfr); 399 400 /* run in interrupt mode for all others */ 401 return bcm2835aux_spi_transfer_one_irq(master, spi, tfr); 402 } 403 404 static int bcm2835aux_spi_prepare_message(struct spi_master *master, 405 struct spi_message *msg) 406 { 407 struct spi_device *spi = msg->spi; 408 struct bcm2835aux_spi *bs = spi_master_get_devdata(master); 409 410 bs->cntl[0] = BCM2835_AUX_SPI_CNTL0_ENABLE | 411 BCM2835_AUX_SPI_CNTL0_VAR_WIDTH | 412 BCM2835_AUX_SPI_CNTL0_MSBF_OUT; 413 bs->cntl[1] = BCM2835_AUX_SPI_CNTL1_MSBF_IN; 414 415 /* handle all the modes */ 416 if (spi->mode & SPI_CPOL) { 417 bs->cntl[0] |= BCM2835_AUX_SPI_CNTL0_CPOL; 418 bs->cntl[0] |= BCM2835_AUX_SPI_CNTL0_OUT_RISING; 419 } else { 420 bs->cntl[0] |= BCM2835_AUX_SPI_CNTL0_IN_RISING; 421 } 422 bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL1, bs->cntl[1]); 423 bcm2835aux_wr(bs, BCM2835_AUX_SPI_CNTL0, bs->cntl[0]); 424 425 return 0; 426 } 427 428 static int bcm2835aux_spi_unprepare_message(struct spi_master *master, 429 struct spi_message *msg) 430 { 431 struct bcm2835aux_spi *bs = spi_master_get_devdata(master); 432 433 bcm2835aux_spi_reset_hw(bs); 434 435 return 0; 436 } 437 438 static void bcm2835aux_spi_handle_err(struct spi_master *master, 439 struct spi_message *msg) 440 { 441 struct bcm2835aux_spi *bs = spi_master_get_devdata(master); 442 443 bcm2835aux_spi_reset_hw(bs); 444 } 445 446 static int bcm2835aux_spi_setup(struct spi_device *spi) 447 { 448 int ret; 449 450 /* sanity check for native cs */ 451 if (spi->mode & SPI_NO_CS) 452 return 0; 453 if (gpio_is_valid(spi->cs_gpio)) { 454 /* with gpio-cs set the GPIO to the correct level 455 * and as output (in case the dt has the gpio not configured 456 * as output but native cs) 457 */ 458 ret = gpio_direction_output(spi->cs_gpio, 459 (spi->mode & SPI_CS_HIGH) ? 0 : 1); 460 if (ret) 461 dev_err(&spi->dev, 462 "could not set gpio %i as output: %i\n", 463 spi->cs_gpio, ret); 464 465 return ret; 466 } 467 468 /* for dt-backwards compatibility: only support native on CS0 469 * known things not supported with broken native CS: 470 * * multiple chip-selects: cs0-cs2 are all 471 * simultaniously asserted whenever there is a transfer 472 * this even includes SPI_NO_CS 473 * * SPI_CS_HIGH: cs are always asserted low 474 * * cs_change: cs is deasserted after each spi_transfer 475 * * cs_delay_usec: cs is always deasserted one SCK cycle 476 * after the last transfer 477 * probably more... 478 */ 479 dev_warn(&spi->dev, 480 "Native CS is not supported - please configure cs-gpio in device-tree\n"); 481 482 if (spi->chip_select == 0) 483 return 0; 484 485 dev_warn(&spi->dev, "Native CS is not working for cs > 0\n"); 486 487 return -EINVAL; 488 } 489 490 static int bcm2835aux_spi_probe(struct platform_device *pdev) 491 { 492 struct spi_master *master; 493 struct bcm2835aux_spi *bs; 494 unsigned long clk_hz; 495 int err; 496 497 master = spi_alloc_master(&pdev->dev, sizeof(*bs)); 498 if (!master) 499 return -ENOMEM; 500 501 platform_set_drvdata(pdev, master); 502 master->mode_bits = (SPI_CPOL | SPI_CS_HIGH | SPI_NO_CS); 503 master->bits_per_word_mask = SPI_BPW_MASK(8); 504 /* even though the driver never officially supported native CS 505 * allow a single native CS for legacy DT support purposes when 506 * no cs-gpio is configured. 507 * Known limitations for native cs are: 508 * * multiple chip-selects: cs0-cs2 are all simultaniously asserted 509 * whenever there is a transfer - this even includes SPI_NO_CS 510 * * SPI_CS_HIGH: is ignores - cs are always asserted low 511 * * cs_change: cs is deasserted after each spi_transfer 512 * * cs_delay_usec: cs is always deasserted one SCK cycle after 513 * a spi_transfer 514 */ 515 master->num_chipselect = 1; 516 master->setup = bcm2835aux_spi_setup; 517 master->transfer_one = bcm2835aux_spi_transfer_one; 518 master->handle_err = bcm2835aux_spi_handle_err; 519 master->prepare_message = bcm2835aux_spi_prepare_message; 520 master->unprepare_message = bcm2835aux_spi_unprepare_message; 521 master->dev.of_node = pdev->dev.of_node; 522 523 bs = spi_master_get_devdata(master); 524 525 /* the main area */ 526 bs->regs = devm_platform_ioremap_resource(pdev, 0); 527 if (IS_ERR(bs->regs)) { 528 err = PTR_ERR(bs->regs); 529 goto out_master_put; 530 } 531 532 bs->clk = devm_clk_get(&pdev->dev, NULL); 533 if (IS_ERR(bs->clk)) { 534 err = PTR_ERR(bs->clk); 535 dev_err(&pdev->dev, "could not get clk: %d\n", err); 536 goto out_master_put; 537 } 538 539 bs->irq = platform_get_irq(pdev, 0); 540 if (bs->irq <= 0) { 541 err = bs->irq ? bs->irq : -ENODEV; 542 goto out_master_put; 543 } 544 545 /* this also enables the HW block */ 546 err = clk_prepare_enable(bs->clk); 547 if (err) { 548 dev_err(&pdev->dev, "could not prepare clock: %d\n", err); 549 goto out_master_put; 550 } 551 552 /* just checking if the clock returns a sane value */ 553 clk_hz = clk_get_rate(bs->clk); 554 if (!clk_hz) { 555 dev_err(&pdev->dev, "clock returns 0 Hz\n"); 556 err = -ENODEV; 557 goto out_clk_disable; 558 } 559 560 /* reset SPI-HW block */ 561 bcm2835aux_spi_reset_hw(bs); 562 563 err = devm_request_irq(&pdev->dev, bs->irq, 564 bcm2835aux_spi_interrupt, 565 IRQF_SHARED, 566 dev_name(&pdev->dev), master); 567 if (err) { 568 dev_err(&pdev->dev, "could not request IRQ: %d\n", err); 569 goto out_clk_disable; 570 } 571 572 err = devm_spi_register_master(&pdev->dev, master); 573 if (err) { 574 dev_err(&pdev->dev, "could not register SPI master: %d\n", err); 575 goto out_clk_disable; 576 } 577 578 bcm2835aux_debugfs_create(bs, dev_name(&pdev->dev)); 579 580 return 0; 581 582 out_clk_disable: 583 clk_disable_unprepare(bs->clk); 584 out_master_put: 585 spi_master_put(master); 586 return err; 587 } 588 589 static int bcm2835aux_spi_remove(struct platform_device *pdev) 590 { 591 struct spi_master *master = platform_get_drvdata(pdev); 592 struct bcm2835aux_spi *bs = spi_master_get_devdata(master); 593 594 bcm2835aux_debugfs_remove(bs); 595 596 bcm2835aux_spi_reset_hw(bs); 597 598 /* disable the HW block by releasing the clock */ 599 clk_disable_unprepare(bs->clk); 600 601 return 0; 602 } 603 604 static const struct of_device_id bcm2835aux_spi_match[] = { 605 { .compatible = "brcm,bcm2835-aux-spi", }, 606 {} 607 }; 608 MODULE_DEVICE_TABLE(of, bcm2835aux_spi_match); 609 610 static struct platform_driver bcm2835aux_spi_driver = { 611 .driver = { 612 .name = "spi-bcm2835aux", 613 .of_match_table = bcm2835aux_spi_match, 614 }, 615 .probe = bcm2835aux_spi_probe, 616 .remove = bcm2835aux_spi_remove, 617 }; 618 module_platform_driver(bcm2835aux_spi_driver); 619 620 MODULE_DESCRIPTION("SPI controller driver for Broadcom BCM2835 aux"); 621 MODULE_AUTHOR("Martin Sperl <kernel@martin.sperl.org>"); 622 MODULE_LICENSE("GPL"); 623