xref: /openbmc/linux/drivers/spi/Kconfig (revision ae3473231e77a3f1909d48cd144cebe5e1d049b3)
1#
2# SPI driver configuration
3#
4# NOTE:  the reason this doesn't show SPI slave support is mostly that
5# nobody's needed a slave side API yet.  The master-role API is not
6# fully appropriate there, so it'd need some thought to do well.
7#
8menuconfig SPI
9	bool "SPI support"
10	depends on HAS_IOMEM
11	help
12	  The "Serial Peripheral Interface" is a low level synchronous
13	  protocol.  Chips that support SPI can have data transfer rates
14	  up to several tens of Mbit/sec.  Chips are addressed with a
15	  controller and a chipselect.  Most SPI slaves don't support
16	  dynamic device discovery; some are even write-only or read-only.
17
18	  SPI is widely used by microcontrollers to talk with sensors,
19	  eeprom and flash memory, codecs and various other controller
20	  chips, analog to digital (and d-to-a) converters, and more.
21	  MMC and SD cards can be accessed using SPI protocol; and for
22	  DataFlash cards used in MMC sockets, SPI must always be used.
23
24	  SPI is one of a family of similar protocols using a four wire
25	  interface (select, clock, data in, data out) including Microwire
26	  (half duplex), SSP, SSI, and PSP.  This driver framework should
27	  work with most such devices and controllers.
28
29if SPI
30
31config SPI_DEBUG
32	bool "Debug support for SPI drivers"
33	depends on DEBUG_KERNEL
34	help
35	  Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
36	  sysfs, and debugfs support in SPI controller and protocol drivers.
37
38#
39# MASTER side ... talking to discrete SPI slave chips including microcontrollers
40#
41
42config SPI_MASTER
43#	bool "SPI Master Support"
44	bool
45	default SPI
46	help
47	  If your system has an master-capable SPI controller (which
48	  provides the clock and chipselect), you can enable that
49	  controller and the protocol drivers for the SPI slave chips
50	  that are connected.
51
52if SPI_MASTER
53
54comment "SPI Master Controller Drivers"
55
56config SPI_ALTERA
57	tristate "Altera SPI Controller"
58	select SPI_BITBANG
59	help
60	  This is the driver for the Altera SPI Controller.
61
62config SPI_ATH79
63	tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
64	depends on ATH79 && GPIOLIB
65	select SPI_BITBANG
66	help
67	  This enables support for the SPI controller present on the
68	  Atheros AR71XX/AR724X/AR913X SoCs.
69
70config SPI_ARMADA_3700
71	tristate "Marvell Armada 3700 SPI Controller"
72	depends on (ARCH_MVEBU && OF) || COMPILE_TEST
73	help
74	  This enables support for the SPI controller present on the
75	  Marvell Armada 3700 SoCs.
76
77config SPI_ATMEL
78	tristate "Atmel SPI Controller"
79	depends on HAS_DMA
80	depends on (ARCH_AT91 || AVR32 || COMPILE_TEST)
81	help
82	  This selects a driver for the Atmel SPI Controller, present on
83	  many AT32 (AVR32) and AT91 (ARM) chips.
84
85config SPI_AU1550
86	tristate "Au1550/Au1200/Au1300 SPI Controller"
87	depends on MIPS_ALCHEMY
88	select SPI_BITBANG
89	help
90	  If you say yes to this option, support will be included for the
91	  PSC SPI controller found on Au1550, Au1200 and Au1300 series.
92
93config SPI_AXI_SPI_ENGINE
94	tristate "Analog Devices AXI SPI Engine controller"
95	depends on HAS_IOMEM
96	help
97	  This enables support for the Analog Devices AXI SPI Engine SPI controller.
98	  It is part of the SPI Engine framework that is used in some Analog Devices
99	  reference designs for FPGAs.
100
101config SPI_BCM2835
102	tristate "BCM2835 SPI controller"
103	depends on GPIOLIB
104	depends on ARCH_BCM2835 || COMPILE_TEST
105	help
106	  This selects a driver for the Broadcom BCM2835 SPI master.
107
108	  The BCM2835 contains two types of SPI master controller; the
109	  "universal SPI master", and the regular SPI controller. This driver
110	  is for the regular SPI controller. Slave mode operation is not also
111	  not supported.
112
113config SPI_BCM2835AUX
114	tristate "BCM2835 SPI auxiliary controller"
115	depends on (ARCH_BCM2835 && GPIOLIB) || COMPILE_TEST
116	help
117	  This selects a driver for the Broadcom BCM2835 SPI aux master.
118
119	  The BCM2835 contains two types of SPI master controller; the
120	  "universal SPI master", and the regular SPI controller.
121	  This driver is for the universal/auxiliary SPI controller.
122
123config SPI_BFIN5XX
124	tristate "SPI controller driver for ADI Blackfin5xx"
125	depends on BLACKFIN && !BF60x
126	help
127	  This is the SPI controller master driver for Blackfin 5xx processor.
128
129config SPI_ADI_V3
130	tristate "SPI controller v3 for ADI"
131	depends on BF60x
132	help
133	  This is the SPI controller v3 master driver
134	  found on Blackfin 60x processor.
135
136config SPI_BFIN_SPORT
137	tristate "SPI bus via Blackfin SPORT"
138	depends on BLACKFIN
139	help
140	  Enable support for a SPI bus via the Blackfin SPORT peripheral.
141
142config SPI_BCM53XX
143	tristate "Broadcom BCM53xx SPI controller"
144	depends on ARCH_BCM_5301X
145	depends on BCMA_POSSIBLE
146	select BCMA
147	help
148          Enable support for the SPI controller on Broadcom BCM53xx ARM SoCs.
149
150config SPI_BCM63XX
151	tristate "Broadcom BCM63xx SPI controller"
152	depends on BCM63XX || COMPILE_TEST
153	help
154          Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
155
156config SPI_BCM63XX_HSSPI
157	tristate "Broadcom BCM63XX HS SPI controller driver"
158	depends on BCM63XX || COMPILE_TEST
159	help
160	  This enables support for the High Speed SPI controller present on
161	  newer Broadcom BCM63XX SoCs.
162
163config SPI_BCM_QSPI
164	tristate "Broadcom BSPI and MSPI controller support"
165	depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || COMPILE_TEST
166	default ARCH_BCM_IPROC
167	help
168	  Enables support for the Broadcom SPI flash and MSPI controller.
169	  Select this option for any one of BRCMSTB, iProc NSP and NS2 SoCs
170	  based platforms. This driver works for both SPI master for spi-nor
171	  flash device as well as MSPI device.
172
173config SPI_BITBANG
174	tristate "Utilities for Bitbanging SPI masters"
175	help
176	  With a few GPIO pins, your system can bitbang the SPI protocol.
177	  Select this to get SPI support through I/O pins (GPIO, parallel
178	  port, etc).  Or, some systems' SPI master controller drivers use
179	  this code to manage the per-word or per-transfer accesses to the
180	  hardware shift registers.
181
182	  This is library code, and is automatically selected by drivers that
183	  need it.  You only need to select this explicitly to support driver
184	  modules that aren't part of this kernel tree.
185
186config SPI_BUTTERFLY
187	tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
188	depends on PARPORT
189	select SPI_BITBANG
190	help
191	  This uses a custom parallel port cable to connect to an AVR
192	  Butterfly <http://www.atmel.com/products/avr/butterfly>, an
193	  inexpensive battery powered microcontroller evaluation board.
194	  This same cable can be used to flash new firmware.
195
196config SPI_CADENCE
197	tristate "Cadence SPI controller"
198	help
199	  This selects the Cadence SPI controller master driver
200	  used by Xilinx Zynq and ZynqMP.
201
202config SPI_CLPS711X
203	tristate "CLPS711X host SPI controller"
204	depends on ARCH_CLPS711X || COMPILE_TEST
205	help
206	  This enables dedicated general purpose SPI/Microwire1-compatible
207	  master mode interface (SSI1) for CLPS711X-based CPUs.
208
209config SPI_COLDFIRE_QSPI
210	tristate "Freescale Coldfire QSPI controller"
211	depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
212	help
213	  This enables support for the Coldfire QSPI controller in master
214	  mode.
215
216config SPI_DAVINCI
217	tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
218	depends on ARCH_DAVINCI || ARCH_KEYSTONE
219	select SPI_BITBANG
220	help
221	  SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
222
223config SPI_DESIGNWARE
224	tristate "DesignWare SPI controller core support"
225	help
226	  general driver for SPI controller core from DesignWare
227
228config SPI_DW_PCI
229	tristate "PCI interface driver for DW SPI core"
230	depends on SPI_DESIGNWARE && PCI
231
232config SPI_DW_MID_DMA
233	bool "DMA support for DW SPI controller on Intel MID platform"
234	depends on SPI_DW_PCI && DW_DMAC_PCI
235
236config SPI_DW_MMIO
237	tristate "Memory-mapped io interface driver for DW SPI core"
238	depends on SPI_DESIGNWARE
239
240config SPI_DLN2
241       tristate "Diolan DLN-2 USB SPI adapter"
242       depends on MFD_DLN2
243       help
244         If you say yes to this option, support will be included for Diolan
245         DLN2, a USB to SPI interface.
246
247         This driver can also be built as a module.  If so, the module
248         will be called spi-dln2.
249
250config SPI_EFM32
251	tristate "EFM32 SPI controller"
252	depends on OF && ARM && (ARCH_EFM32 || COMPILE_TEST)
253	select SPI_BITBANG
254	help
255	  Driver for the spi controller found on Energy Micro's EFM32 SoCs.
256
257config SPI_EP93XX
258	tristate "Cirrus Logic EP93xx SPI controller"
259	depends on HAS_DMA
260	depends on ARCH_EP93XX || COMPILE_TEST
261	help
262	  This enables using the Cirrus EP93xx SPI controller in master
263	  mode.
264
265config SPI_FALCON
266	tristate "Falcon SPI controller support"
267	depends on SOC_FALCON
268	help
269	  The external bus unit (EBU) found on the FALC-ON SoC has SPI
270	  emulation that is designed for serial flash access. This driver
271	  has only been tested with m25p80 type chips. The hardware has no
272	  support for other types of SPI peripherals.
273
274config SPI_FSL_LPSPI
275	tristate "Freescale i.MX LPSPI controller"
276	depends on ARCH_MXC || COMPILE_TEST
277	help
278	  This enables Freescale i.MX LPSPI controllers in master mode.
279
280config SPI_GPIO
281	tristate "GPIO-based bitbanging SPI Master"
282	depends on GPIOLIB || COMPILE_TEST
283	select SPI_BITBANG
284	help
285	  This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
286	  interface to manage MOSI, MISO, SCK, and chipselect signals.  SPI
287	  slaves connected to a bus using this driver are configured as usual,
288	  except that the spi_board_info.controller_data holds the GPIO number
289	  for the chipselect used by this controller driver.
290
291	  Note that this driver often won't achieve even 1 Mbit/sec speeds,
292	  making it unusually slow for SPI.  If your platform can inline
293	  GPIO operations, you should be able to leverage that for better
294	  speed with a custom version of this driver; see the source code.
295
296config SPI_IMG_SPFI
297	tristate "IMG SPFI controller"
298	depends on MIPS || COMPILE_TEST
299	help
300	  This enables support for the SPFI master controller found on
301	  IMG SoCs.
302
303config SPI_IMX
304	tristate "Freescale i.MX SPI controllers"
305	depends on ARCH_MXC || COMPILE_TEST
306	select SPI_BITBANG
307	help
308	  This enables using the Freescale i.MX SPI controllers in master
309	  mode.
310
311config SPI_JCORE
312	tristate "J-Core SPI Master"
313	depends on OF && (SUPERH || COMPILE_TEST)
314	help
315	  This enables support for the SPI master controller in the J-Core
316	  synthesizable, open source SoC.
317
318config SPI_LM70_LLP
319	tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
320	depends on PARPORT
321	select SPI_BITBANG
322	help
323	  This driver supports the NS LM70 LLP Evaluation Board,
324	  which interfaces to an LM70 temperature sensor using
325	  a parallel port.
326
327config SPI_LP8841_RTC
328	tristate "ICP DAS LP-8841 SPI Controller for RTC"
329	depends on MACH_PXA27X_DT || COMPILE_TEST
330	help
331	  This driver provides an SPI master device to drive Maxim
332	  DS-1302 real time clock.
333
334	  Say N here unless you plan to run the kernel on an ICP DAS
335	  LP-8x4x industrial computer.
336
337config SPI_MPC52xx
338	tristate "Freescale MPC52xx SPI (non-PSC) controller support"
339	depends on PPC_MPC52xx
340	help
341	  This drivers supports the MPC52xx SPI controller in master SPI
342	  mode.
343
344config SPI_MPC52xx_PSC
345	tristate "Freescale MPC52xx PSC SPI controller"
346	depends on PPC_MPC52xx
347	help
348	  This enables using the Freescale MPC52xx Programmable Serial
349	  Controller in master SPI mode.
350
351config SPI_MPC512x_PSC
352	tristate "Freescale MPC512x PSC SPI controller"
353	depends on PPC_MPC512x
354	help
355	  This enables using the Freescale MPC5121 Programmable Serial
356	  Controller in SPI master mode.
357
358config SPI_FSL_LIB
359	tristate
360	depends on OF
361
362config SPI_FSL_CPM
363	tristate
364	depends on FSL_SOC
365
366config SPI_FSL_SPI
367	tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
368	depends on OF
369	select SPI_FSL_LIB
370	select SPI_FSL_CPM if FSL_SOC
371	help
372	  This enables using the Freescale SPI controllers in master mode.
373	  MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
374	  MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
375	  This also enables using the Aeroflex Gaisler GRLIB SPI controller in
376	  master mode.
377
378config SPI_FSL_DSPI
379	tristate "Freescale DSPI controller"
380	select REGMAP_MMIO
381	depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
382	help
383	  This enables support for the Freescale DSPI controller in master
384	  mode. VF610 platform uses the controller.
385
386config SPI_FSL_ESPI
387	tristate "Freescale eSPI controller"
388	depends on FSL_SOC
389	help
390	  This enables using the Freescale eSPI controllers in master mode.
391	  From MPC8536, 85xx platform uses the controller, and all P10xx,
392	  P20xx, P30xx,P40xx, P50xx uses this controller.
393
394config SPI_MESON_SPIFC
395	tristate "Amlogic Meson SPIFC controller"
396	depends on ARCH_MESON || COMPILE_TEST
397	select REGMAP_MMIO
398	help
399	  This enables master mode support for the SPIFC (SPI flash
400	  controller) available in Amlogic Meson SoCs.
401
402config SPI_MT65XX
403	tristate "MediaTek SPI controller"
404	depends on ARCH_MEDIATEK || COMPILE_TEST
405	help
406	  This selects the MediaTek(R) SPI bus driver.
407	  If you want to use MediaTek(R) SPI interface,
408	  say Y or M here.If you are not sure, say N.
409	  SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
410
411config SPI_NUC900
412	tristate "Nuvoton NUC900 series SPI"
413	depends on ARCH_W90X900
414	select SPI_BITBANG
415	help
416	  SPI driver for Nuvoton NUC900 series ARM SoCs
417
418config SPI_OC_TINY
419	tristate "OpenCores tiny SPI"
420	depends on GPIOLIB || COMPILE_TEST
421	select SPI_BITBANG
422	help
423	  This is the driver for OpenCores tiny SPI master controller.
424
425config SPI_OCTEON
426	tristate "Cavium OCTEON SPI controller"
427	depends on CAVIUM_OCTEON_SOC
428	help
429	  SPI host driver for the hardware found on some Cavium OCTEON
430	  SOCs.
431
432config SPI_OMAP_UWIRE
433	tristate "OMAP1 MicroWire"
434	depends on ARCH_OMAP1
435	select SPI_BITBANG
436	help
437	  This hooks up to the MicroWire controller on OMAP1 chips.
438
439config SPI_OMAP24XX
440	tristate "McSPI driver for OMAP"
441	depends on HAS_DMA
442	depends on ARCH_OMAP2PLUS || COMPILE_TEST
443	select SG_SPLIT
444	help
445	  SPI master controller for OMAP24XX and later Multichannel SPI
446	  (McSPI) modules.
447
448config SPI_TI_QSPI
449	tristate "DRA7xxx QSPI controller support"
450	depends on ARCH_OMAP2PLUS || COMPILE_TEST
451	help
452	  QSPI master controller for DRA7xxx used for flash devices.
453	  This device supports single, dual and quad read support, while
454	  it only supports single write mode.
455
456config SPI_OMAP_100K
457	tristate "OMAP SPI 100K"
458	depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
459	help
460	  OMAP SPI 100K master controller for omap7xx boards.
461
462config SPI_ORION
463	tristate "Orion SPI master"
464	depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST
465	help
466	  This enables using the SPI master controller on the Orion
467	  and MVEBU chips.
468
469config SPI_PIC32
470	tristate "Microchip PIC32 series SPI"
471	depends on MACH_PIC32 || COMPILE_TEST
472	help
473	  SPI driver for Microchip PIC32 SPI master controller.
474
475config SPI_PIC32_SQI
476	tristate "Microchip PIC32 Quad SPI driver"
477	depends on MACH_PIC32 || COMPILE_TEST
478	depends on HAS_DMA
479	help
480	  SPI driver for PIC32 Quad SPI controller.
481
482config SPI_PL022
483	tristate "ARM AMBA PL022 SSP controller"
484	depends on ARM_AMBA
485	default y if MACH_U300
486	default y if ARCH_REALVIEW
487	default y if INTEGRATOR_IMPD1
488	default y if ARCH_VERSATILE
489	help
490	  This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
491	  controller. If you have an embedded system with an AMBA(R)
492	  bus and a PL022 controller, say Y or M here.
493
494config SPI_PPC4xx
495	tristate "PPC4xx SPI Controller"
496	depends on PPC32 && 4xx
497	select SPI_BITBANG
498	help
499	  This selects a driver for the PPC4xx SPI Controller.
500
501config SPI_PXA2XX
502	tristate "PXA2xx SSP SPI master"
503	depends on (ARCH_PXA || PCI || ACPI)
504	select PXA_SSP if ARCH_PXA
505	help
506	  This enables using a PXA2xx or Sodaville SSP port as a SPI master
507	  controller. The driver can be configured to use any SSP port and
508	  additional documentation can be found a Documentation/spi/pxa2xx.
509
510config SPI_PXA2XX_PCI
511	def_tristate SPI_PXA2XX && PCI && COMMON_CLK
512
513config SPI_ROCKCHIP
514	tristate "Rockchip SPI controller driver"
515	help
516	  This selects a driver for Rockchip SPI controller.
517
518	  If you say yes to this option, support will be included for
519	  RK3066, RK3188 and RK3288 families of SPI controller.
520	  Rockchip SPI controller support DMA transport and PIO mode.
521	  The main usecase of this controller is to use spi flash as boot
522	  device.
523
524config SPI_RB4XX
525	tristate "Mikrotik RB4XX SPI master"
526	depends on SPI_MASTER && ATH79
527	help
528	  SPI controller driver for the Mikrotik RB4xx series boards.
529
530config SPI_RSPI
531	tristate "Renesas RSPI/QSPI controller"
532	depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
533	help
534	  SPI driver for Renesas RSPI and QSPI blocks.
535
536config SPI_QUP
537	tristate "Qualcomm SPI controller with QUP interface"
538	depends on ARCH_QCOM || (ARM && COMPILE_TEST)
539	help
540	  Qualcomm Universal Peripheral (QUP) core is an AHB slave that
541	  provides a common data path (an output FIFO and an input FIFO)
542	  for serial peripheral interface (SPI) mini-core. SPI in master
543	  mode supports up to 50MHz, up to four chip selects, programmable
544	  data path from 4 bits to 32 bits and numerous protocol variants.
545
546	  This driver can also be built as a module.  If so, the module
547	  will be called spi_qup.
548
549config SPI_S3C24XX
550	tristate "Samsung S3C24XX series SPI"
551	depends on ARCH_S3C24XX
552	select SPI_BITBANG
553	help
554	  SPI driver for Samsung S3C24XX series ARM SoCs
555
556config SPI_S3C24XX_FIQ
557	bool "S3C24XX driver with FIQ pseudo-DMA"
558	depends on SPI_S3C24XX
559	select FIQ
560	help
561	  Enable FIQ support for the S3C24XX SPI driver to provide pseudo
562	  DMA by using the fast-interrupt request framework, This allows
563	  the driver to get DMA-like performance when there are either
564	  no free DMA channels, or when doing transfers that required both
565	  TX and RX data paths.
566
567config SPI_S3C64XX
568	tristate "Samsung S3C64XX series type SPI"
569	depends on (PLAT_SAMSUNG || ARCH_EXYNOS || COMPILE_TEST)
570	help
571	  SPI driver for Samsung S3C64XX and newer SoCs.
572
573config SPI_SC18IS602
574	tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
575	depends on I2C
576	help
577	  SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
578
579config SPI_SH_MSIOF
580	tristate "SuperH MSIOF SPI controller"
581	depends on HAVE_CLK && HAS_DMA
582	depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
583	help
584	  SPI driver for SuperH and SH Mobile MSIOF blocks.
585
586config SPI_SH
587	tristate "SuperH SPI controller"
588	depends on SUPERH || COMPILE_TEST
589	help
590	  SPI driver for SuperH SPI blocks.
591
592config SPI_SH_SCI
593	tristate "SuperH SCI SPI controller"
594	depends on SUPERH
595	select SPI_BITBANG
596	help
597	  SPI driver for SuperH SCI blocks.
598
599config SPI_SH_HSPI
600	tristate "SuperH HSPI controller"
601	depends on ARCH_RENESAS || COMPILE_TEST
602	help
603	  SPI driver for SuperH HSPI blocks.
604
605config SPI_SIRF
606	tristate "CSR SiRFprimaII SPI controller"
607	depends on SIRF_DMA
608	select SPI_BITBANG
609	help
610	  SPI driver for CSR SiRFprimaII SoCs
611
612config SPI_ST_SSC4
613	tristate "STMicroelectronics SPI SSC-based driver"
614	depends on ARCH_STI || COMPILE_TEST
615	help
616	  STMicroelectronics SoCs support for SPI. If you say yes to
617	  this option, support will be included for the SSC driven SPI.
618
619config SPI_SUN4I
620	tristate "Allwinner A10 SoCs SPI controller"
621	depends on ARCH_SUNXI || COMPILE_TEST
622	help
623	  SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
624
625config SPI_SUN6I
626	tristate "Allwinner A31 SPI controller"
627	depends on ARCH_SUNXI || COMPILE_TEST
628	depends on RESET_CONTROLLER
629	help
630	  This enables using the SPI controller on the Allwinner A31 SoCs.
631
632config SPI_MXS
633	tristate "Freescale MXS SPI controller"
634	depends on ARCH_MXS
635	select STMP_DEVICE
636	help
637	  SPI driver for Freescale MXS devices.
638
639config SPI_TEGRA114
640	tristate "NVIDIA Tegra114 SPI Controller"
641	depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
642	depends on RESET_CONTROLLER && HAS_DMA
643	help
644	  SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
645	  is different than the older SoCs SPI controller and also register interface
646	  get changed with this controller.
647
648config SPI_TEGRA20_SFLASH
649	tristate "Nvidia Tegra20 Serial flash Controller"
650	depends on ARCH_TEGRA || COMPILE_TEST
651	depends on RESET_CONTROLLER
652	help
653	  SPI driver for Nvidia Tegra20 Serial flash Controller interface.
654	  The main usecase of this controller is to use spi flash as boot
655	  device.
656
657config SPI_TEGRA20_SLINK
658	tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
659	depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
660	depends on RESET_CONTROLLER && HAS_DMA
661	help
662	  SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
663
664config SPI_THUNDERX
665	tristate "Cavium ThunderX SPI controller"
666	depends on PCI && 64BIT && (ARM64 || COMPILE_TEST)
667	help
668	  SPI host driver for the hardware found on Cavium ThunderX
669	  SOCs.
670
671config SPI_TOPCLIFF_PCH
672	tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
673	depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
674	help
675	  SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
676	  used in some x86 embedded processors.
677
678	  This driver also supports the ML7213/ML7223/ML7831, a companion chip
679	  for the Atom E6xx series and compatible with the Intel EG20T PCH.
680
681config SPI_TXX9
682	tristate "Toshiba TXx9 SPI controller"
683	depends on GPIOLIB && (CPU_TX49XX || COMPILE_TEST)
684	help
685	  SPI driver for Toshiba TXx9 MIPS SoCs
686
687config SPI_XCOMM
688	tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
689	depends on I2C
690	help
691	  Support for the SPI-I2C bridge found on the Analog Devices
692	  AD-FMCOMMS1-EBZ board.
693
694config SPI_XILINX
695	tristate "Xilinx SPI controller common module"
696	depends on HAS_IOMEM
697	select SPI_BITBANG
698	help
699	  This exposes the SPI controller IP from the Xilinx EDK.
700
701	  See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
702	  Product Specification document (DS464) for hardware details.
703
704	  Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
705
706config SPI_XLP
707	tristate "Netlogic XLP SPI controller driver"
708	depends on CPU_XLP || ARCH_VULCAN || COMPILE_TEST
709	help
710	  Enable support for the SPI controller on the Netlogic XLP SoCs.
711	  Currently supported XLP variants are XLP8XX, XLP3XX, XLP2XX, XLP9XX
712	  and XLP5XX.
713
714	  If you have a Netlogic XLP platform say Y here.
715	  If unsure, say N.
716
717config SPI_XTENSA_XTFPGA
718	tristate "Xtensa SPI controller for xtfpga"
719	depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
720	select SPI_BITBANG
721	help
722	  SPI driver for xtfpga SPI master controller.
723
724	  This simple SPI master controller is built into xtfpga bitstreams
725	  and is used to control daughterboard audio codec. It always transfers
726	  16 bit words in SPI mode 0, automatically asserting CS on transfer
727	  start and deasserting on end.
728
729config SPI_ZYNQMP_GQSPI
730	tristate "Xilinx ZynqMP GQSPI controller"
731	depends on SPI_MASTER && HAS_DMA
732	help
733	  Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
734
735#
736# Add new SPI master controllers in alphabetical order above this line
737#
738
739#
740# There are lots of SPI device types, with sensors and memory
741# being probably the most widely used ones.
742#
743comment "SPI Protocol Masters"
744
745config SPI_SPIDEV
746	tristate "User mode SPI device driver support"
747	help
748	  This supports user mode SPI protocol drivers.
749
750	  Note that this application programming interface is EXPERIMENTAL
751	  and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
752
753config SPI_LOOPBACK_TEST
754	tristate "spi loopback test framework support"
755	depends on m
756	help
757	  This enables the SPI loopback testing framework driver
758
759	  primarily used for development of spi_master drivers
760	  and to detect regressions
761
762config SPI_TLE62X0
763	tristate "Infineon TLE62X0 (for power switching)"
764	depends on SYSFS
765	help
766	  SPI driver for Infineon TLE62X0 series line driver chips,
767	  such as the TLE6220, TLE6230 and TLE6240.  This provides a
768	  sysfs interface, with each line presented as a kind of GPIO
769	  exposing both switch control and diagnostic feedback.
770
771#
772# Add new SPI protocol masters in alphabetical order above this line
773#
774
775endif # SPI_MASTER
776
777# (slave support would go here)
778
779endif # SPI
780