1 // SPDX-License-Identifier: GPL-2.0 2 // Copyright (c) 2017-2018, The Linux Foundation. All rights reserved. 3 4 #include <linux/clk.h> 5 #include <linux/slab.h> 6 #include <linux/dma-mapping.h> 7 #include <linux/io.h> 8 #include <linux/module.h> 9 #include <linux/of.h> 10 #include <linux/of_platform.h> 11 #include <linux/pinctrl/consumer.h> 12 #include <linux/platform_device.h> 13 #include <linux/qcom-geni-se.h> 14 15 /** 16 * DOC: Overview 17 * 18 * Generic Interface (GENI) Serial Engine (SE) Wrapper driver is introduced 19 * to manage GENI firmware based Qualcomm Universal Peripheral (QUP) Wrapper 20 * controller. QUP Wrapper is designed to support various serial bus protocols 21 * like UART, SPI, I2C, I3C, etc. 22 */ 23 24 /** 25 * DOC: Hardware description 26 * 27 * GENI based QUP is a highly-flexible and programmable module for supporting 28 * a wide range of serial interfaces like UART, SPI, I2C, I3C, etc. A single 29 * QUP module can provide upto 8 serial interfaces, using its internal 30 * serial engines. The actual configuration is determined by the target 31 * platform configuration. The protocol supported by each interface is 32 * determined by the firmware loaded to the serial engine. Each SE consists 33 * of a DMA Engine and GENI sub modules which enable serial engines to 34 * support FIFO and DMA modes of operation. 35 * 36 * 37 * +-----------------------------------------+ 38 * |QUP Wrapper | 39 * | +----------------------------+ | 40 * --QUP & SE Clocks--> | Serial Engine N | +-IO------> 41 * | | ... | | Interface 42 * <---Clock Perf.----+ +----+-----------------------+ | | 43 * State Interface | | Serial Engine 1 | | | 44 * | | | | | 45 * | | | | | 46 * <--------AHB-------> | | | | 47 * | | +----+ | 48 * | | | | 49 * | | | | 50 * <------SE IRQ------+ +----------------------------+ | 51 * | | 52 * +-----------------------------------------+ 53 * 54 * Figure 1: GENI based QUP Wrapper 55 * 56 * The GENI submodules include primary and secondary sequencers which are 57 * used to drive TX & RX operations. On serial interfaces that operate using 58 * master-slave model, primary sequencer drives both TX & RX operations. On 59 * serial interfaces that operate using peer-to-peer model, primary sequencer 60 * drives TX operation and secondary sequencer drives RX operation. 61 */ 62 63 /** 64 * DOC: Software description 65 * 66 * GENI SE Wrapper driver is structured into 2 parts: 67 * 68 * geni_wrapper represents QUP Wrapper controller. This part of the driver 69 * manages QUP Wrapper information such as hardware version, clock 70 * performance table that is common to all the internal serial engines. 71 * 72 * geni_se represents serial engine. This part of the driver manages serial 73 * engine information such as clocks, containing QUP Wrapper, etc. This part 74 * of driver also supports operations (eg. initialize the concerned serial 75 * engine, select between FIFO and DMA mode of operation etc.) that are 76 * common to all the serial engines and are independent of serial interfaces. 77 */ 78 79 #define MAX_CLK_PERF_LEVEL 32 80 #define NUM_AHB_CLKS 2 81 82 /** 83 * @struct geni_wrapper - Data structure to represent the QUP Wrapper Core 84 * @dev: Device pointer of the QUP wrapper core 85 * @base: Base address of this instance of QUP wrapper core 86 * @ahb_clks: Handle to the primary & secondary AHB clocks 87 */ 88 struct geni_wrapper { 89 struct device *dev; 90 void __iomem *base; 91 struct clk_bulk_data ahb_clks[NUM_AHB_CLKS]; 92 }; 93 94 #define QUP_HW_VER_REG 0x4 95 96 /* Common SE registers */ 97 #define GENI_INIT_CFG_REVISION 0x0 98 #define GENI_S_INIT_CFG_REVISION 0x4 99 #define GENI_OUTPUT_CTRL 0x24 100 #define GENI_CGC_CTRL 0x28 101 #define GENI_CLK_CTRL_RO 0x60 102 #define GENI_IF_DISABLE_RO 0x64 103 #define GENI_FW_S_REVISION_RO 0x6c 104 #define SE_GENI_BYTE_GRAN 0x254 105 #define SE_GENI_TX_PACKING_CFG0 0x260 106 #define SE_GENI_TX_PACKING_CFG1 0x264 107 #define SE_GENI_RX_PACKING_CFG0 0x284 108 #define SE_GENI_RX_PACKING_CFG1 0x288 109 #define SE_GENI_M_GP_LENGTH 0x910 110 #define SE_GENI_S_GP_LENGTH 0x914 111 #define SE_DMA_TX_PTR_L 0xc30 112 #define SE_DMA_TX_PTR_H 0xc34 113 #define SE_DMA_TX_ATTR 0xc38 114 #define SE_DMA_TX_LEN 0xc3c 115 #define SE_DMA_TX_IRQ_EN 0xc48 116 #define SE_DMA_TX_IRQ_EN_SET 0xc4c 117 #define SE_DMA_TX_IRQ_EN_CLR 0xc50 118 #define SE_DMA_TX_LEN_IN 0xc54 119 #define SE_DMA_TX_MAX_BURST 0xc5c 120 #define SE_DMA_RX_PTR_L 0xd30 121 #define SE_DMA_RX_PTR_H 0xd34 122 #define SE_DMA_RX_ATTR 0xd38 123 #define SE_DMA_RX_LEN 0xd3c 124 #define SE_DMA_RX_IRQ_EN 0xd48 125 #define SE_DMA_RX_IRQ_EN_SET 0xd4c 126 #define SE_DMA_RX_IRQ_EN_CLR 0xd50 127 #define SE_DMA_RX_LEN_IN 0xd54 128 #define SE_DMA_RX_MAX_BURST 0xd5c 129 #define SE_DMA_RX_FLUSH 0xd60 130 #define SE_GSI_EVENT_EN 0xe18 131 #define SE_IRQ_EN 0xe1c 132 #define SE_DMA_GENERAL_CFG 0xe30 133 134 /* GENI_OUTPUT_CTRL fields */ 135 #define DEFAULT_IO_OUTPUT_CTRL_MSK GENMASK(6, 0) 136 137 /* GENI_CGC_CTRL fields */ 138 #define CFG_AHB_CLK_CGC_ON BIT(0) 139 #define CFG_AHB_WR_ACLK_CGC_ON BIT(1) 140 #define DATA_AHB_CLK_CGC_ON BIT(2) 141 #define SCLK_CGC_ON BIT(3) 142 #define TX_CLK_CGC_ON BIT(4) 143 #define RX_CLK_CGC_ON BIT(5) 144 #define EXT_CLK_CGC_ON BIT(6) 145 #define PROG_RAM_HCLK_OFF BIT(8) 146 #define PROG_RAM_SCLK_OFF BIT(9) 147 #define DEFAULT_CGC_EN GENMASK(6, 0) 148 149 /* SE_GSI_EVENT_EN fields */ 150 #define DMA_RX_EVENT_EN BIT(0) 151 #define DMA_TX_EVENT_EN BIT(1) 152 #define GENI_M_EVENT_EN BIT(2) 153 #define GENI_S_EVENT_EN BIT(3) 154 155 /* SE_IRQ_EN fields */ 156 #define DMA_RX_IRQ_EN BIT(0) 157 #define DMA_TX_IRQ_EN BIT(1) 158 #define GENI_M_IRQ_EN BIT(2) 159 #define GENI_S_IRQ_EN BIT(3) 160 161 /* SE_DMA_GENERAL_CFG */ 162 #define DMA_RX_CLK_CGC_ON BIT(0) 163 #define DMA_TX_CLK_CGC_ON BIT(1) 164 #define DMA_AHB_SLV_CFG_ON BIT(2) 165 #define AHB_SEC_SLV_CLK_CGC_ON BIT(3) 166 #define DUMMY_RX_NON_BUFFERABLE BIT(4) 167 #define RX_DMA_ZERO_PADDING_EN BIT(5) 168 #define RX_DMA_IRQ_DELAY_MSK GENMASK(8, 6) 169 #define RX_DMA_IRQ_DELAY_SHFT 6 170 171 /** 172 * geni_se_get_qup_hw_version() - Read the QUP wrapper Hardware version 173 * @se: Pointer to the corresponding serial engine. 174 * 175 * Return: Hardware Version of the wrapper. 176 */ 177 u32 geni_se_get_qup_hw_version(struct geni_se *se) 178 { 179 struct geni_wrapper *wrapper = se->wrapper; 180 181 return readl_relaxed(wrapper->base + QUP_HW_VER_REG); 182 } 183 EXPORT_SYMBOL(geni_se_get_qup_hw_version); 184 185 static void geni_se_io_set_mode(void __iomem *base) 186 { 187 u32 val; 188 189 val = readl_relaxed(base + SE_IRQ_EN); 190 val |= GENI_M_IRQ_EN | GENI_S_IRQ_EN; 191 val |= DMA_TX_IRQ_EN | DMA_RX_IRQ_EN; 192 writel_relaxed(val, base + SE_IRQ_EN); 193 194 val = readl_relaxed(base + SE_GENI_DMA_MODE_EN); 195 val &= ~GENI_DMA_MODE_EN; 196 writel_relaxed(val, base + SE_GENI_DMA_MODE_EN); 197 198 writel_relaxed(0, base + SE_GSI_EVENT_EN); 199 } 200 201 static void geni_se_io_init(void __iomem *base) 202 { 203 u32 val; 204 205 val = readl_relaxed(base + GENI_CGC_CTRL); 206 val |= DEFAULT_CGC_EN; 207 writel_relaxed(val, base + GENI_CGC_CTRL); 208 209 val = readl_relaxed(base + SE_DMA_GENERAL_CFG); 210 val |= AHB_SEC_SLV_CLK_CGC_ON | DMA_AHB_SLV_CFG_ON; 211 val |= DMA_TX_CLK_CGC_ON | DMA_RX_CLK_CGC_ON; 212 writel_relaxed(val, base + SE_DMA_GENERAL_CFG); 213 214 writel_relaxed(DEFAULT_IO_OUTPUT_CTRL_MSK, base + GENI_OUTPUT_CTRL); 215 writel_relaxed(FORCE_DEFAULT, base + GENI_FORCE_DEFAULT_REG); 216 } 217 218 /** 219 * geni_se_init() - Initialize the GENI serial engine 220 * @se: Pointer to the concerned serial engine. 221 * @rx_wm: Receive watermark, in units of FIFO words. 222 * @rx_rfr_wm: Ready-for-receive watermark, in units of FIFO words. 223 * 224 * This function is used to initialize the GENI serial engine, configure 225 * receive watermark and ready-for-receive watermarks. 226 */ 227 void geni_se_init(struct geni_se *se, u32 rx_wm, u32 rx_rfr) 228 { 229 u32 val; 230 231 geni_se_io_init(se->base); 232 geni_se_io_set_mode(se->base); 233 234 writel_relaxed(rx_wm, se->base + SE_GENI_RX_WATERMARK_REG); 235 writel_relaxed(rx_rfr, se->base + SE_GENI_RX_RFR_WATERMARK_REG); 236 237 val = readl_relaxed(se->base + SE_GENI_M_IRQ_EN); 238 val |= M_COMMON_GENI_M_IRQ_EN; 239 writel_relaxed(val, se->base + SE_GENI_M_IRQ_EN); 240 241 val = readl_relaxed(se->base + SE_GENI_S_IRQ_EN); 242 val |= S_COMMON_GENI_S_IRQ_EN; 243 writel_relaxed(val, se->base + SE_GENI_S_IRQ_EN); 244 } 245 EXPORT_SYMBOL(geni_se_init); 246 247 static void geni_se_select_fifo_mode(struct geni_se *se) 248 { 249 u32 proto = geni_se_read_proto(se); 250 u32 val; 251 252 writel_relaxed(0, se->base + SE_GSI_EVENT_EN); 253 writel_relaxed(0xffffffff, se->base + SE_GENI_M_IRQ_CLEAR); 254 writel_relaxed(0xffffffff, se->base + SE_GENI_S_IRQ_CLEAR); 255 writel_relaxed(0xffffffff, se->base + SE_DMA_TX_IRQ_CLR); 256 writel_relaxed(0xffffffff, se->base + SE_DMA_RX_IRQ_CLR); 257 writel_relaxed(0xffffffff, se->base + SE_IRQ_EN); 258 259 val = readl_relaxed(se->base + SE_GENI_M_IRQ_EN); 260 if (proto != GENI_SE_UART) { 261 val |= M_CMD_DONE_EN | M_TX_FIFO_WATERMARK_EN; 262 val |= M_RX_FIFO_WATERMARK_EN | M_RX_FIFO_LAST_EN; 263 } 264 writel_relaxed(val, se->base + SE_GENI_M_IRQ_EN); 265 266 val = readl_relaxed(se->base + SE_GENI_S_IRQ_EN); 267 if (proto != GENI_SE_UART) 268 val |= S_CMD_DONE_EN; 269 writel_relaxed(val, se->base + SE_GENI_S_IRQ_EN); 270 271 val = readl_relaxed(se->base + SE_GENI_DMA_MODE_EN); 272 val &= ~GENI_DMA_MODE_EN; 273 writel_relaxed(val, se->base + SE_GENI_DMA_MODE_EN); 274 } 275 276 static void geni_se_select_dma_mode(struct geni_se *se) 277 { 278 u32 val; 279 280 writel_relaxed(0, se->base + SE_GSI_EVENT_EN); 281 writel_relaxed(0xffffffff, se->base + SE_GENI_M_IRQ_CLEAR); 282 writel_relaxed(0xffffffff, se->base + SE_GENI_S_IRQ_CLEAR); 283 writel_relaxed(0xffffffff, se->base + SE_DMA_TX_IRQ_CLR); 284 writel_relaxed(0xffffffff, se->base + SE_DMA_RX_IRQ_CLR); 285 writel_relaxed(0xffffffff, se->base + SE_IRQ_EN); 286 287 val = readl_relaxed(se->base + SE_GENI_DMA_MODE_EN); 288 val |= GENI_DMA_MODE_EN; 289 writel_relaxed(val, se->base + SE_GENI_DMA_MODE_EN); 290 } 291 292 /** 293 * geni_se_select_mode() - Select the serial engine transfer mode 294 * @se: Pointer to the concerned serial engine. 295 * @mode: Transfer mode to be selected. 296 */ 297 void geni_se_select_mode(struct geni_se *se, enum geni_se_xfer_mode mode) 298 { 299 WARN_ON(mode != GENI_SE_FIFO && mode != GENI_SE_DMA); 300 301 switch (mode) { 302 case GENI_SE_FIFO: 303 geni_se_select_fifo_mode(se); 304 break; 305 case GENI_SE_DMA: 306 geni_se_select_dma_mode(se); 307 break; 308 case GENI_SE_INVALID: 309 default: 310 break; 311 } 312 } 313 EXPORT_SYMBOL(geni_se_select_mode); 314 315 /** 316 * DOC: Overview 317 * 318 * GENI FIFO packing is highly configurable. TX/RX packing/unpacking consist 319 * of up to 4 operations, each operation represented by 4 configuration vectors 320 * of 10 bits programmed in GENI_TX_PACKING_CFG0 and GENI_TX_PACKING_CFG1 for 321 * TX FIFO and in GENI_RX_PACKING_CFG0 and GENI_RX_PACKING_CFG1 for RX FIFO. 322 * Refer to below examples for detailed bit-field description. 323 * 324 * Example 1: word_size = 7, packing_mode = 4 x 8, msb_to_lsb = 1 325 * 326 * +-----------+-------+-------+-------+-------+ 327 * | | vec_0 | vec_1 | vec_2 | vec_3 | 328 * +-----------+-------+-------+-------+-------+ 329 * | start | 0x6 | 0xe | 0x16 | 0x1e | 330 * | direction | 1 | 1 | 1 | 1 | 331 * | length | 6 | 6 | 6 | 6 | 332 * | stop | 0 | 0 | 0 | 1 | 333 * +-----------+-------+-------+-------+-------+ 334 * 335 * Example 2: word_size = 15, packing_mode = 2 x 16, msb_to_lsb = 0 336 * 337 * +-----------+-------+-------+-------+-------+ 338 * | | vec_0 | vec_1 | vec_2 | vec_3 | 339 * +-----------+-------+-------+-------+-------+ 340 * | start | 0x0 | 0x8 | 0x10 | 0x18 | 341 * | direction | 0 | 0 | 0 | 0 | 342 * | length | 7 | 6 | 7 | 6 | 343 * | stop | 0 | 0 | 0 | 1 | 344 * +-----------+-------+-------+-------+-------+ 345 * 346 * Example 3: word_size = 23, packing_mode = 1 x 32, msb_to_lsb = 1 347 * 348 * +-----------+-------+-------+-------+-------+ 349 * | | vec_0 | vec_1 | vec_2 | vec_3 | 350 * +-----------+-------+-------+-------+-------+ 351 * | start | 0x16 | 0xe | 0x6 | 0x0 | 352 * | direction | 1 | 1 | 1 | 1 | 353 * | length | 7 | 7 | 6 | 0 | 354 * | stop | 0 | 0 | 1 | 0 | 355 * +-----------+-------+-------+-------+-------+ 356 * 357 */ 358 359 #define NUM_PACKING_VECTORS 4 360 #define PACKING_START_SHIFT 5 361 #define PACKING_DIR_SHIFT 4 362 #define PACKING_LEN_SHIFT 1 363 #define PACKING_STOP_BIT BIT(0) 364 #define PACKING_VECTOR_SHIFT 10 365 /** 366 * geni_se_config_packing() - Packing configuration of the serial engine 367 * @se: Pointer to the concerned serial engine 368 * @bpw: Bits of data per transfer word. 369 * @pack_words: Number of words per fifo element. 370 * @msb_to_lsb: Transfer from MSB to LSB or vice-versa. 371 * @tx_cfg: Flag to configure the TX Packing. 372 * @rx_cfg: Flag to configure the RX Packing. 373 * 374 * This function is used to configure the packing rules for the current 375 * transfer. 376 */ 377 void geni_se_config_packing(struct geni_se *se, int bpw, int pack_words, 378 bool msb_to_lsb, bool tx_cfg, bool rx_cfg) 379 { 380 u32 cfg0, cfg1, cfg[NUM_PACKING_VECTORS] = {0}; 381 int len; 382 int temp_bpw = bpw; 383 int idx_start = msb_to_lsb ? bpw - 1 : 0; 384 int idx = idx_start; 385 int idx_delta = msb_to_lsb ? -BITS_PER_BYTE : BITS_PER_BYTE; 386 int ceil_bpw = ALIGN(bpw, BITS_PER_BYTE); 387 int iter = (ceil_bpw * pack_words) / BITS_PER_BYTE; 388 int i; 389 390 if (iter <= 0 || iter > NUM_PACKING_VECTORS) 391 return; 392 393 for (i = 0; i < iter; i++) { 394 len = min_t(int, temp_bpw, BITS_PER_BYTE) - 1; 395 cfg[i] = idx << PACKING_START_SHIFT; 396 cfg[i] |= msb_to_lsb << PACKING_DIR_SHIFT; 397 cfg[i] |= len << PACKING_LEN_SHIFT; 398 399 if (temp_bpw <= BITS_PER_BYTE) { 400 idx = ((i + 1) * BITS_PER_BYTE) + idx_start; 401 temp_bpw = bpw; 402 } else { 403 idx = idx + idx_delta; 404 temp_bpw = temp_bpw - BITS_PER_BYTE; 405 } 406 } 407 cfg[iter - 1] |= PACKING_STOP_BIT; 408 cfg0 = cfg[0] | (cfg[1] << PACKING_VECTOR_SHIFT); 409 cfg1 = cfg[2] | (cfg[3] << PACKING_VECTOR_SHIFT); 410 411 if (tx_cfg) { 412 writel_relaxed(cfg0, se->base + SE_GENI_TX_PACKING_CFG0); 413 writel_relaxed(cfg1, se->base + SE_GENI_TX_PACKING_CFG1); 414 } 415 if (rx_cfg) { 416 writel_relaxed(cfg0, se->base + SE_GENI_RX_PACKING_CFG0); 417 writel_relaxed(cfg1, se->base + SE_GENI_RX_PACKING_CFG1); 418 } 419 420 /* 421 * Number of protocol words in each FIFO entry 422 * 0 - 4x8, four words in each entry, max word size of 8 bits 423 * 1 - 2x16, two words in each entry, max word size of 16 bits 424 * 2 - 1x32, one word in each entry, max word size of 32 bits 425 * 3 - undefined 426 */ 427 if (pack_words || bpw == 32) 428 writel_relaxed(bpw / 16, se->base + SE_GENI_BYTE_GRAN); 429 } 430 EXPORT_SYMBOL(geni_se_config_packing); 431 432 static void geni_se_clks_off(struct geni_se *se) 433 { 434 struct geni_wrapper *wrapper = se->wrapper; 435 436 clk_disable_unprepare(se->clk); 437 clk_bulk_disable_unprepare(ARRAY_SIZE(wrapper->ahb_clks), 438 wrapper->ahb_clks); 439 } 440 441 /** 442 * geni_se_resources_off() - Turn off resources associated with the serial 443 * engine 444 * @se: Pointer to the concerned serial engine. 445 * 446 * Return: 0 on success, standard Linux error codes on failure/error. 447 */ 448 int geni_se_resources_off(struct geni_se *se) 449 { 450 int ret; 451 452 ret = pinctrl_pm_select_sleep_state(se->dev); 453 if (ret) 454 return ret; 455 456 geni_se_clks_off(se); 457 return 0; 458 } 459 EXPORT_SYMBOL(geni_se_resources_off); 460 461 static int geni_se_clks_on(struct geni_se *se) 462 { 463 int ret; 464 struct geni_wrapper *wrapper = se->wrapper; 465 466 ret = clk_bulk_prepare_enable(ARRAY_SIZE(wrapper->ahb_clks), 467 wrapper->ahb_clks); 468 if (ret) 469 return ret; 470 471 ret = clk_prepare_enable(se->clk); 472 if (ret) 473 clk_bulk_disable_unprepare(ARRAY_SIZE(wrapper->ahb_clks), 474 wrapper->ahb_clks); 475 return ret; 476 } 477 478 /** 479 * geni_se_resources_on() - Turn on resources associated with the serial 480 * engine 481 * @se: Pointer to the concerned serial engine. 482 * 483 * Return: 0 on success, standard Linux error codes on failure/error. 484 */ 485 int geni_se_resources_on(struct geni_se *se) 486 { 487 int ret; 488 489 ret = geni_se_clks_on(se); 490 if (ret) 491 return ret; 492 493 ret = pinctrl_pm_select_default_state(se->dev); 494 if (ret) 495 geni_se_clks_off(se); 496 497 return ret; 498 } 499 EXPORT_SYMBOL(geni_se_resources_on); 500 501 /** 502 * geni_se_clk_tbl_get() - Get the clock table to program DFS 503 * @se: Pointer to the concerned serial engine. 504 * @tbl: Table in which the output is returned. 505 * 506 * This function is called by the protocol drivers to determine the different 507 * clock frequencies supported by serial engine core clock. The protocol 508 * drivers use the output to determine the clock frequency index to be 509 * programmed into DFS. 510 * 511 * Return: number of valid performance levels in the table on success, 512 * standard Linux error codes on failure. 513 */ 514 int geni_se_clk_tbl_get(struct geni_se *se, unsigned long **tbl) 515 { 516 unsigned long freq = 0; 517 int i; 518 519 if (se->clk_perf_tbl) { 520 *tbl = se->clk_perf_tbl; 521 return se->num_clk_levels; 522 } 523 524 se->clk_perf_tbl = devm_kcalloc(se->dev, MAX_CLK_PERF_LEVEL, 525 sizeof(*se->clk_perf_tbl), 526 GFP_KERNEL); 527 if (!se->clk_perf_tbl) 528 return -ENOMEM; 529 530 for (i = 0; i < MAX_CLK_PERF_LEVEL; i++) { 531 freq = clk_round_rate(se->clk, freq + 1); 532 if (!freq || freq == se->clk_perf_tbl[i - 1]) 533 break; 534 se->clk_perf_tbl[i] = freq; 535 } 536 se->num_clk_levels = i; 537 *tbl = se->clk_perf_tbl; 538 return se->num_clk_levels; 539 } 540 EXPORT_SYMBOL(geni_se_clk_tbl_get); 541 542 /** 543 * geni_se_clk_freq_match() - Get the matching or closest SE clock frequency 544 * @se: Pointer to the concerned serial engine. 545 * @req_freq: Requested clock frequency. 546 * @index: Index of the resultant frequency in the table. 547 * @res_freq: Resultant frequency which matches or is closer to the 548 * requested frequency. 549 * @exact: Flag to indicate exact multiple requirement of the requested 550 * frequency. 551 * 552 * This function is called by the protocol drivers to determine the matching 553 * or exact multiple of the requested frequency, as provided by the serial 554 * engine clock in order to meet the performance requirements. If there is 555 * no matching or exact multiple of the requested frequency found, then it 556 * selects the closest floor frequency, if exact flag is not set. 557 * 558 * Return: 0 on success, standard Linux error codes on failure. 559 */ 560 int geni_se_clk_freq_match(struct geni_se *se, unsigned long req_freq, 561 unsigned int *index, unsigned long *res_freq, 562 bool exact) 563 { 564 unsigned long *tbl; 565 int num_clk_levels; 566 int i; 567 568 num_clk_levels = geni_se_clk_tbl_get(se, &tbl); 569 if (num_clk_levels < 0) 570 return num_clk_levels; 571 572 if (num_clk_levels == 0) 573 return -EINVAL; 574 575 *res_freq = 0; 576 for (i = 0; i < num_clk_levels; i++) { 577 if (!(tbl[i] % req_freq)) { 578 *index = i; 579 *res_freq = tbl[i]; 580 return 0; 581 } 582 583 if (!(*res_freq) || ((tbl[i] > *res_freq) && 584 (tbl[i] < req_freq))) { 585 *index = i; 586 *res_freq = tbl[i]; 587 } 588 } 589 590 if (exact) 591 return -EINVAL; 592 593 return 0; 594 } 595 EXPORT_SYMBOL(geni_se_clk_freq_match); 596 597 #define GENI_SE_DMA_DONE_EN BIT(0) 598 #define GENI_SE_DMA_EOT_EN BIT(1) 599 #define GENI_SE_DMA_AHB_ERR_EN BIT(2) 600 #define GENI_SE_DMA_EOT_BUF BIT(0) 601 /** 602 * geni_se_tx_dma_prep() - Prepare the serial engine for TX DMA transfer 603 * @se: Pointer to the concerned serial engine. 604 * @buf: Pointer to the TX buffer. 605 * @len: Length of the TX buffer. 606 * @iova: Pointer to store the mapped DMA address. 607 * 608 * This function is used to prepare the buffers for DMA TX. 609 * 610 * Return: 0 on success, standard Linux error codes on failure. 611 */ 612 int geni_se_tx_dma_prep(struct geni_se *se, void *buf, size_t len, 613 dma_addr_t *iova) 614 { 615 struct geni_wrapper *wrapper = se->wrapper; 616 u32 val; 617 618 *iova = dma_map_single(wrapper->dev, buf, len, DMA_TO_DEVICE); 619 if (dma_mapping_error(wrapper->dev, *iova)) 620 return -EIO; 621 622 val = GENI_SE_DMA_DONE_EN; 623 val |= GENI_SE_DMA_EOT_EN; 624 val |= GENI_SE_DMA_AHB_ERR_EN; 625 writel_relaxed(val, se->base + SE_DMA_TX_IRQ_EN_SET); 626 writel_relaxed(lower_32_bits(*iova), se->base + SE_DMA_TX_PTR_L); 627 writel_relaxed(upper_32_bits(*iova), se->base + SE_DMA_TX_PTR_H); 628 writel_relaxed(GENI_SE_DMA_EOT_BUF, se->base + SE_DMA_TX_ATTR); 629 writel_relaxed(len, se->base + SE_DMA_TX_LEN); 630 return 0; 631 } 632 EXPORT_SYMBOL(geni_se_tx_dma_prep); 633 634 /** 635 * geni_se_rx_dma_prep() - Prepare the serial engine for RX DMA transfer 636 * @se: Pointer to the concerned serial engine. 637 * @buf: Pointer to the RX buffer. 638 * @len: Length of the RX buffer. 639 * @iova: Pointer to store the mapped DMA address. 640 * 641 * This function is used to prepare the buffers for DMA RX. 642 * 643 * Return: 0 on success, standard Linux error codes on failure. 644 */ 645 int geni_se_rx_dma_prep(struct geni_se *se, void *buf, size_t len, 646 dma_addr_t *iova) 647 { 648 struct geni_wrapper *wrapper = se->wrapper; 649 u32 val; 650 651 *iova = dma_map_single(wrapper->dev, buf, len, DMA_FROM_DEVICE); 652 if (dma_mapping_error(wrapper->dev, *iova)) 653 return -EIO; 654 655 val = GENI_SE_DMA_DONE_EN; 656 val |= GENI_SE_DMA_EOT_EN; 657 val |= GENI_SE_DMA_AHB_ERR_EN; 658 writel_relaxed(val, se->base + SE_DMA_RX_IRQ_EN_SET); 659 writel_relaxed(lower_32_bits(*iova), se->base + SE_DMA_RX_PTR_L); 660 writel_relaxed(upper_32_bits(*iova), se->base + SE_DMA_RX_PTR_H); 661 /* RX does not have EOT buffer type bit. So just reset RX_ATTR */ 662 writel_relaxed(0, se->base + SE_DMA_RX_ATTR); 663 writel_relaxed(len, se->base + SE_DMA_RX_LEN); 664 return 0; 665 } 666 EXPORT_SYMBOL(geni_se_rx_dma_prep); 667 668 /** 669 * geni_se_tx_dma_unprep() - Unprepare the serial engine after TX DMA transfer 670 * @se: Pointer to the concerned serial engine. 671 * @iova: DMA address of the TX buffer. 672 * @len: Length of the TX buffer. 673 * 674 * This function is used to unprepare the DMA buffers after DMA TX. 675 */ 676 void geni_se_tx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len) 677 { 678 struct geni_wrapper *wrapper = se->wrapper; 679 680 if (iova && !dma_mapping_error(wrapper->dev, iova)) 681 dma_unmap_single(wrapper->dev, iova, len, DMA_TO_DEVICE); 682 } 683 EXPORT_SYMBOL(geni_se_tx_dma_unprep); 684 685 /** 686 * geni_se_rx_dma_unprep() - Unprepare the serial engine after RX DMA transfer 687 * @se: Pointer to the concerned serial engine. 688 * @iova: DMA address of the RX buffer. 689 * @len: Length of the RX buffer. 690 * 691 * This function is used to unprepare the DMA buffers after DMA RX. 692 */ 693 void geni_se_rx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len) 694 { 695 struct geni_wrapper *wrapper = se->wrapper; 696 697 if (iova && !dma_mapping_error(wrapper->dev, iova)) 698 dma_unmap_single(wrapper->dev, iova, len, DMA_FROM_DEVICE); 699 } 700 EXPORT_SYMBOL(geni_se_rx_dma_unprep); 701 702 static int geni_se_probe(struct platform_device *pdev) 703 { 704 struct device *dev = &pdev->dev; 705 struct resource *res; 706 struct geni_wrapper *wrapper; 707 int ret; 708 709 wrapper = devm_kzalloc(dev, sizeof(*wrapper), GFP_KERNEL); 710 if (!wrapper) 711 return -ENOMEM; 712 713 wrapper->dev = dev; 714 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 715 wrapper->base = devm_ioremap_resource(dev, res); 716 if (IS_ERR(wrapper->base)) 717 return PTR_ERR(wrapper->base); 718 719 wrapper->ahb_clks[0].id = "m-ahb"; 720 wrapper->ahb_clks[1].id = "s-ahb"; 721 ret = devm_clk_bulk_get(dev, NUM_AHB_CLKS, wrapper->ahb_clks); 722 if (ret) { 723 dev_err(dev, "Err getting AHB clks %d\n", ret); 724 return ret; 725 } 726 727 dev_set_drvdata(dev, wrapper); 728 dev_dbg(dev, "GENI SE Driver probed\n"); 729 return devm_of_platform_populate(dev); 730 } 731 732 static const struct of_device_id geni_se_dt_match[] = { 733 { .compatible = "qcom,geni-se-qup", }, 734 {} 735 }; 736 MODULE_DEVICE_TABLE(of, geni_se_dt_match); 737 738 static struct platform_driver geni_se_driver = { 739 .driver = { 740 .name = "geni_se_qup", 741 .of_match_table = geni_se_dt_match, 742 }, 743 .probe = geni_se_probe, 744 }; 745 module_platform_driver(geni_se_driver); 746 747 MODULE_DESCRIPTION("GENI Serial Engine Driver"); 748 MODULE_LICENSE("GPL v2"); 749