1 /* SPDX-License-Identifier: GPL-2.0 */ 2 #ifndef _WD719X_H_ 3 #define _WD719X_H_ 4 5 #define WD719X_SG 255 /* Scatter/gather size */ 6 7 struct wd719x_sglist { 8 __le32 ptr; 9 __le32 length; 10 } __packed; 11 12 enum wd719x_card_type { 13 WD719X_TYPE_UNKNOWN = 0, 14 WD719X_TYPE_7193, 15 WD719X_TYPE_7197, 16 WD719X_TYPE_7296, 17 }; 18 19 union wd719x_regs { 20 __le32 all; /* All Status at once */ 21 struct { 22 u8 OPC; /* Opcode register */ 23 u8 SCSI; /* SCSI Errors */ 24 u8 SUE; /* Spider unique Errors */ 25 u8 INT; /* Interrupt Status */ 26 } bytes; 27 }; 28 29 /* Spider Command Block (SCB) */ 30 struct wd719x_scb { 31 __le32 Int_SCB; /* 00-03 Internal SCB link pointer (must be cleared) */ 32 u8 SCB_opcode; /* 04 SCB Command opcode */ 33 u8 CDB_tag; /* 05 SCSI Tag byte for CDB queues (0 if untagged) */ 34 u8 lun; /* 06 SCSI LUN */ 35 u8 devid; /* 07 SCSI Device ID */ 36 u8 CDB[16]; /* 08-23 SCSI CDB (16 bytes as defined by ANSI spec. */ 37 __le32 data_p; /* 24-27 Data transfer address (or SG list address) */ 38 __le32 data_length; /* 28-31 Data transfer Length (or SG list length) */ 39 __le32 CDB_link; /* 32-35 SCSI CDB Link Ptr */ 40 __le32 sense_buf; /* 36-39 Auto request sense buffer address */ 41 u8 sense_buf_length;/* 40 Auto request sense transfer length */ 42 u8 reserved; /* 41 reserved */ 43 u8 SCB_options; /* 42 SCB-options */ 44 u8 SCB_tag_msg; /* 43 Tagged messages options */ 45 /* Not filled in by host */ 46 __le32 req_ptr; /* 44-47 Ptr to Host Request returned on interrupt */ 47 u8 host_opcode; /* 48 Host Command Opcode (same as AMR_00) */ 48 u8 scsi_stat; /* 49 SCSI Status returned */ 49 u8 ret_error; /* 50 SPIDER Unique Error Code returned (SUE) */ 50 u8 int_stat; /* 51 Message u8 / Interrupt Status byte returned */ 51 __le32 transferred; /* 52-55 Bytes Transferred */ 52 u8 last_trans[3]; /* 56-58 Bytes Transferred in last session */ 53 u8 length; /* 59 SCSI Messages Length (1-8) */ 54 u8 sync_offset; /* 60 Synchronous offset */ 55 u8 sync_rate; /* 61 Synchronous rate */ 56 u8 flags[2]; /* 62-63 SCB specific flags (local to each thread) */ 57 /* everything below is for driver use (not used by card) */ 58 dma_addr_t phys; /* bus address of the SCB */ 59 struct scsi_cmnd *cmd; /* a copy of the pointer we were passed */ 60 struct list_head list; 61 struct wd719x_sglist sg_list[WD719X_SG] __aligned(8); /* SG list */ 62 } __packed; 63 64 struct wd719x { 65 struct Scsi_Host *sh; /* pointer to host structure */ 66 struct pci_dev *pdev; 67 void __iomem *base; 68 enum wd719x_card_type type; /* type of card */ 69 void *fw_virt; /* firmware buffer CPU address */ 70 dma_addr_t fw_phys; /* firmware buffer bus address */ 71 size_t fw_size; /* firmware buffer size */ 72 struct wd719x_host_param *params; /* host parameters (EEPROM) */ 73 dma_addr_t params_phys; /* host parameters bus address */ 74 void *hash_virt; /* hash table CPU address */ 75 dma_addr_t hash_phys; /* hash table bus address */ 76 struct list_head active_scbs; 77 struct list_head free_scbs; 78 }; 79 80 /* timeout delays in microsecs */ 81 #define WD719X_WAIT_FOR_CMD_READY 500 82 #define WD719X_WAIT_FOR_RISC 2000 83 #define WD719X_WAIT_FOR_SCSI_RESET 3000000 84 85 /* All commands except 0x00 generate an interrupt */ 86 #define WD719X_CMD_READY 0x00 /* Command register ready (or noop) */ 87 #define WD719X_CMD_INIT_RISC 0x01 /* Initialize RISC */ 88 /* 0x02 is reserved */ 89 #define WD719X_CMD_BUSRESET 0x03 /* Assert SCSI bus reset */ 90 #define WD719X_CMD_READ_FIRMVER 0x04 /* Read the Firmware Revision */ 91 #define WD719X_CMD_ECHO_BYTES 0x05 /* Echo command bytes (DW) */ 92 /* 0x06 is reserved */ 93 /* 0x07 is reserved */ 94 #define WD719X_CMD_GET_PARAM 0x08 /* Get programmable parameters */ 95 #define WD719X_CMD_SET_PARAM 0x09 /* Set programmable parameters */ 96 #define WD719X_CMD_SLEEP 0x0a /* Put SPIDER to sleep */ 97 #define WD719X_CMD_READ_INIT 0x0b /* Read initialization parameters */ 98 #define WD719X_CMD_RESTORE_INIT 0x0c /* Restore initialization parameters */ 99 /* 0x0d is reserved */ 100 /* 0x0e is reserved */ 101 /* 0x0f is reserved */ 102 #define WD719X_CMD_ABORT_TAG 0x10 /* Send Abort tag message to target */ 103 #define WD719X_CMD_ABORT 0x11 /* Send Abort message to target */ 104 #define WD719X_CMD_RESET 0x12 /* Send Reset message to target */ 105 #define WD719X_CMD_INIT_SCAM 0x13 /* Initiate SCAM */ 106 #define WD719X_CMD_GET_SYNC 0x14 /* Get synchronous rates */ 107 #define WD719X_CMD_SET_SYNC 0x15 /* Set synchronous rates */ 108 #define WD719X_CMD_GET_WIDTH 0x16 /* Get SCSI bus width */ 109 #define WD719X_CMD_SET_WIDTH 0x17 /* Set SCSI bus width */ 110 #define WD719X_CMD_GET_TAGS 0x18 /* Get tag flags */ 111 #define WD719X_CMD_SET_TAGS 0x19 /* Set tag flags */ 112 #define WD719X_CMD_GET_PARAM2 0x1a /* Get programmable params (format 2) */ 113 #define WD719X_CMD_SET_PARAM2 0x1b /* Set programmable params (format 2) */ 114 /* Commands with request pointers (mailbox) */ 115 #define WD719X_CMD_PROCESS_SCB 0x80 /* Process SCSI Control Block (SCB) */ 116 /* No interrupt generated on acceptance of SCB pointer */ 117 118 /* interrupt status defines */ 119 #define WD719X_INT_NONE 0x00 /* No interrupt pending */ 120 #define WD719X_INT_NOERRORS 0x01 /* Command completed with no errors */ 121 #define WD719X_INT_LINKNOERRORS 0x02 /* link cmd completed with no errors */ 122 #define WD719X_INT_LINKNOSTATUS 0x03 /* link cmd completed with no flag set */ 123 #define WD719X_INT_ERRORSLOGGED 0x04 /* cmd completed with errors logged */ 124 #define WD719X_INT_SPIDERFAILED 0x05 /* cmd failed without valid SCSI status */ 125 #define WD719X_INT_BADINT 0x80 /* unsolicited interrupt */ 126 #define WD719X_INT_PIOREADY 0xf0 /* data ready for PIO output */ 127 128 /* Spider Unique Error Codes (SUE) */ 129 #define WD719X_SUE_NOERRORS 0x00 /* No errors detected by SPIDER */ 130 #define WD719X_SUE_REJECTED 0x01 /* Command Rejected (bad opcode/param) */ 131 #define WD719X_SUE_SCBQFULL 0x02 /* SCB queue full */ 132 /* 0x03 is reserved */ 133 #define WD719X_SUE_TERM 0x04 /* Host terminated SCB via primative cmd */ 134 #define WD719X_SUE_CHAN1PAR 0x05 /* PCI Channel 1 parity error occurred */ 135 #define WD719X_SUE_CHAN1ABORT 0x06 /* PCI Channel 1 system abort occurred */ 136 #define WD719X_SUE_CHAN23PAR 0x07 /* PCI Channel 2/3 parity error occurred */ 137 #define WD719X_SUE_CHAN23ABORT 0x08 /* PCI Channel 2/3 system abort occurred */ 138 #define WD719X_SUE_TIMEOUT 0x10 /* Selection/reselection timeout */ 139 #define WD719X_SUE_RESET 0x11 /* SCSI bus reset occurred */ 140 #define WD719X_SUE_BUSERROR 0x12 /* SCSI bus error */ 141 #define WD719X_SUE_WRONGWAY 0x13 /* Wrong data transfer dir set by target */ 142 #define WD719X_SUE_BADPHASE 0x14 /* SCSI phase illegal or unexpected */ 143 #define WD719X_SUE_TOOLONG 0x15 /* target requested too much data */ 144 #define WD719X_SUE_BUSFREE 0x16 /* Unexpected SCSI bus free */ 145 #define WD719X_SUE_ARSDONE 0x17 /* Auto request sense executed */ 146 #define WD719X_SUE_IGNORED 0x18 /* SCSI message was ignored by target */ 147 #define WD719X_SUE_WRONGTAGS 0x19 /* Tagged SCB & tags off (or vice versa) */ 148 #define WD719X_SUE_BADTAGS 0x1a /* Wrong tag message type for target */ 149 #define WD719X_SUE_NOSCAMID 0x1b /* No SCAM soft ID available */ 150 151 /* code sizes */ 152 #define WD719X_HASH_TABLE_SIZE 4096 153 154 /* Advanced Mode Registers */ 155 /* Regs 0x00..0x1f are for Advanced Mode of the card (RISC is running). */ 156 #define WD719X_AMR_COMMAND 0x00 157 #define WD719X_AMR_CMD_PARAM 0x01 158 #define WD719X_AMR_CMD_PARAM_2 0x02 159 #define WD719X_AMR_CMD_PARAM_3 0x03 160 #define WD719X_AMR_SCB_IN 0x04 161 162 #define WD719X_AMR_BIOS_SHARE_INT 0x0f 163 164 #define WD719X_AMR_SCB_OUT 0x18 165 #define WD719X_AMR_OP_CODE 0x1c 166 #define WD719X_AMR_SCSI_STATUS 0x1d 167 #define WD719X_AMR_SCB_ERROR 0x1e 168 #define WD719X_AMR_INT_STATUS 0x1f 169 170 #define WD719X_DISABLE_INT 0x80 171 172 /* SCB flags */ 173 #define WD719X_SCB_FLAGS_CHECK_DIRECTION 0x01 174 #define WD719X_SCB_FLAGS_PCI_TO_SCSI 0x02 175 #define WD719X_SCB_FLAGS_AUTO_REQUEST_SENSE 0x10 176 #define WD719X_SCB_FLAGS_DO_SCATTER_GATHER 0x20 177 #define WD719X_SCB_FLAGS_NO_DISCONNECT 0x40 178 179 /* PCI Registers used for reset, initial code download */ 180 /* Regs 0x20..0x3f are for Normal (DOS) mode (RISC is asleep). */ 181 #define WD719X_PCI_GPIO_CONTROL 0x3C 182 #define WD719X_PCI_GPIO_DATA 0x3D 183 #define WD719X_PCI_PORT_RESET 0x3E 184 #define WD719X_PCI_MODE_SELECT 0x3F 185 186 #define WD719X_PCI_EXTERNAL_ADDR 0x60 187 #define WD719X_PCI_INTERNAL_ADDR 0x64 188 #define WD719X_PCI_DMA_TRANSFER_SIZE 0x66 189 #define WD719X_PCI_CHANNEL2_3CMD 0x68 190 #define WD719X_PCI_CHANNEL2_3STATUS 0x69 191 192 #define WD719X_GPIO_ID_BITS 0x0a 193 #define WD719X_PRAM_BASE_ADDR 0x00 194 195 /* codes written to or read from the card */ 196 #define WD719X_PCI_RESET 0x01 197 #define WD719X_ENABLE_ADVANCE_MODE 0x01 198 199 #define WD719X_START_CHANNEL2_3DMA 0x17 200 #define WD719X_START_CHANNEL2_3DONE 0x01 201 #define WD719X_START_CHANNEL2_3ABORT 0x20 202 203 /* 33C296 GPIO bits for EEPROM pins */ 204 #define WD719X_EE_DI (1 << 1) 205 #define WD719X_EE_CS (1 << 2) 206 #define WD719X_EE_CLK (1 << 3) 207 #define WD719X_EE_DO (1 << 4) 208 209 /* EEPROM contents */ 210 struct wd719x_eeprom_header { 211 u8 sig1; 212 u8 sig2; 213 u8 version; 214 u8 checksum; 215 u8 cfg_offset; 216 u8 cfg_size; 217 u8 setup_offset; 218 u8 setup_size; 219 } __packed; 220 221 #define WD719X_EE_SIG1 0 222 #define WD719X_EE_SIG2 1 223 #define WD719X_EE_VERSION 2 224 #define WD719X_EE_CHECKSUM 3 225 #define WD719X_EE_CFG_OFFSET 4 226 #define WD719X_EE_CFG_SIZE 5 227 #define WD719X_EE_SETUP_OFFSET 6 228 #define WD719X_EE_SETUP_SIZE 7 229 230 #define WD719X_EE_SCSI_ID_MASK 0xf 231 232 /* SPIDER Host Parameters Block (=EEPROM configuration block) */ 233 struct wd719x_host_param { 234 u8 ch_1_th; /* FIFO threshold */ 235 u8 scsi_conf; /* SCSI configuration */ 236 u8 own_scsi_id; /* controller SCSI ID */ 237 u8 sel_timeout; /* selection timeout*/ 238 u8 sleep_timer; /* seep timer */ 239 __le16 cdb_size;/* CDB size groups */ 240 __le16 tag_en; /* Tag msg enables (ID 0-15) */ 241 u8 scsi_pad; /* SCSI pad control */ 242 __le32 wide; /* WIDE msg options (ID 0-15) */ 243 __le32 sync; /* SYNC msg options (ID 0-15) */ 244 u8 soft_mask; /* soft error mask */ 245 u8 unsol_mask; /* unsolicited error mask */ 246 } __packed; 247 248 #endif /* _WD719X_H_ */ 249