1 /* 2 * Driver for Western Digital WD7193, WD7197 and WD7296 SCSI cards 3 * Copyright 2013 Ondrej Zary 4 * 5 * Original driver by 6 * Aaron Dewell <dewell@woods.net> 7 * Gaerti <Juergen.Gaertner@mbox.si.uni-hannover.de> 8 * 9 * HW documentation available in book: 10 * 11 * SPIDER Command Protocol 12 * by Chandru M. Sippy 13 * SCSI Storage Products (MCP) 14 * Western Digital Corporation 15 * 09-15-95 16 * 17 * http://web.archive.org/web/20070717175254/http://sun1.rrzn.uni-hannover.de/gaertner.juergen/wd719x/Linux/Docu/Spider/ 18 */ 19 20 /* 21 * Driver workflow: 22 * 1. SCSI command is transformed to SCB (Spider Control Block) by the 23 * queuecommand function. 24 * 2. The address of the SCB is stored in a list to be able to access it, if 25 * something goes wrong. 26 * 3. The address of the SCB is written to the Controller, which loads the SCB 27 * via BM-DMA and processes it. 28 * 4. After it has finished, it generates an interrupt, and sets registers. 29 * 30 * flaws: 31 * - abort/reset functions 32 * 33 * ToDo: 34 * - tagged queueing 35 */ 36 37 #include <linux/interrupt.h> 38 #include <linux/module.h> 39 #include <linux/delay.h> 40 #include <linux/pci.h> 41 #include <linux/firmware.h> 42 #include <linux/eeprom_93cx6.h> 43 #include <scsi/scsi_cmnd.h> 44 #include <scsi/scsi_device.h> 45 #include <scsi/scsi_host.h> 46 #include "wd719x.h" 47 48 /* low-level register access */ 49 static inline u8 wd719x_readb(struct wd719x *wd, u8 reg) 50 { 51 return ioread8(wd->base + reg); 52 } 53 54 static inline u32 wd719x_readl(struct wd719x *wd, u8 reg) 55 { 56 return ioread32(wd->base + reg); 57 } 58 59 static inline void wd719x_writeb(struct wd719x *wd, u8 reg, u8 val) 60 { 61 iowrite8(val, wd->base + reg); 62 } 63 64 static inline void wd719x_writew(struct wd719x *wd, u8 reg, u16 val) 65 { 66 iowrite16(val, wd->base + reg); 67 } 68 69 static inline void wd719x_writel(struct wd719x *wd, u8 reg, u32 val) 70 { 71 iowrite32(val, wd->base + reg); 72 } 73 74 /* wait until the command register is ready */ 75 static inline int wd719x_wait_ready(struct wd719x *wd) 76 { 77 int i = 0; 78 79 do { 80 if (wd719x_readb(wd, WD719X_AMR_COMMAND) == WD719X_CMD_READY) 81 return 0; 82 udelay(1); 83 } while (i++ < WD719X_WAIT_FOR_CMD_READY); 84 85 dev_err(&wd->pdev->dev, "command register is not ready: 0x%02x\n", 86 wd719x_readb(wd, WD719X_AMR_COMMAND)); 87 88 return -ETIMEDOUT; 89 } 90 91 /* poll interrupt status register until command finishes */ 92 static inline int wd719x_wait_done(struct wd719x *wd, int timeout) 93 { 94 u8 status; 95 96 while (timeout > 0) { 97 status = wd719x_readb(wd, WD719X_AMR_INT_STATUS); 98 if (status) 99 break; 100 timeout--; 101 udelay(1); 102 } 103 104 if (timeout <= 0) { 105 dev_err(&wd->pdev->dev, "direct command timed out\n"); 106 return -ETIMEDOUT; 107 } 108 109 if (status != WD719X_INT_NOERRORS) { 110 dev_err(&wd->pdev->dev, "direct command failed, status 0x%02x, SUE 0x%02x\n", 111 status, wd719x_readb(wd, WD719X_AMR_SCB_ERROR)); 112 return -EIO; 113 } 114 115 return 0; 116 } 117 118 static int wd719x_direct_cmd(struct wd719x *wd, u8 opcode, u8 dev, u8 lun, 119 u8 tag, dma_addr_t data, int timeout) 120 { 121 int ret = 0; 122 123 /* clear interrupt status register (allow command register to clear) */ 124 wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE); 125 126 /* Wait for the Command register to become free */ 127 if (wd719x_wait_ready(wd)) 128 return -ETIMEDOUT; 129 130 /* make sure we get NO interrupts */ 131 dev |= WD719X_DISABLE_INT; 132 wd719x_writeb(wd, WD719X_AMR_CMD_PARAM, dev); 133 wd719x_writeb(wd, WD719X_AMR_CMD_PARAM_2, lun); 134 wd719x_writeb(wd, WD719X_AMR_CMD_PARAM_3, tag); 135 if (data) 136 wd719x_writel(wd, WD719X_AMR_SCB_IN, data); 137 138 /* clear interrupt status register again */ 139 wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE); 140 141 /* Now, write the command */ 142 wd719x_writeb(wd, WD719X_AMR_COMMAND, opcode); 143 144 if (timeout) /* wait for the command to complete */ 145 ret = wd719x_wait_done(wd, timeout); 146 147 /* clear interrupt status register (clean up) */ 148 if (opcode != WD719X_CMD_READ_FIRMVER) 149 wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE); 150 151 return ret; 152 } 153 154 static void wd719x_destroy(struct wd719x *wd) 155 { 156 struct wd719x_scb *scb; 157 158 /* stop the RISC */ 159 if (wd719x_direct_cmd(wd, WD719X_CMD_SLEEP, 0, 0, 0, 0, 160 WD719X_WAIT_FOR_RISC)) 161 dev_warn(&wd->pdev->dev, "RISC sleep command failed\n"); 162 /* disable RISC */ 163 wd719x_writeb(wd, WD719X_PCI_MODE_SELECT, 0); 164 165 /* free all SCBs */ 166 list_for_each_entry(scb, &wd->active_scbs, list) 167 pci_free_consistent(wd->pdev, sizeof(struct wd719x_scb), scb, 168 scb->phys); 169 list_for_each_entry(scb, &wd->free_scbs, list) 170 pci_free_consistent(wd->pdev, sizeof(struct wd719x_scb), scb, 171 scb->phys); 172 /* free internal buffers */ 173 pci_free_consistent(wd->pdev, wd->fw_size, wd->fw_virt, wd->fw_phys); 174 wd->fw_virt = NULL; 175 pci_free_consistent(wd->pdev, WD719X_HASH_TABLE_SIZE, wd->hash_virt, 176 wd->hash_phys); 177 wd->hash_virt = NULL; 178 pci_free_consistent(wd->pdev, sizeof(struct wd719x_host_param), 179 wd->params, wd->params_phys); 180 wd->params = NULL; 181 free_irq(wd->pdev->irq, wd); 182 } 183 184 /* finish a SCSI command, mark SCB (if any) as free, unmap buffers */ 185 static void wd719x_finish_cmd(struct scsi_cmnd *cmd, int result) 186 { 187 struct wd719x *wd = shost_priv(cmd->device->host); 188 struct wd719x_scb *scb = (struct wd719x_scb *) cmd->host_scribble; 189 190 if (scb) { 191 list_move(&scb->list, &wd->free_scbs); 192 dma_unmap_single(&wd->pdev->dev, cmd->SCp.dma_handle, 193 SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE); 194 scsi_dma_unmap(cmd); 195 } 196 cmd->result = result << 16; 197 cmd->scsi_done(cmd); 198 } 199 200 /* Build a SCB and send it to the card */ 201 static int wd719x_queuecommand(struct Scsi_Host *sh, struct scsi_cmnd *cmd) 202 { 203 int i, count_sg; 204 unsigned long flags; 205 struct wd719x_scb *scb; 206 struct wd719x *wd = shost_priv(sh); 207 dma_addr_t phys; 208 209 cmd->host_scribble = NULL; 210 211 /* get a free SCB - either from existing ones or allocate a new one */ 212 spin_lock_irqsave(wd->sh->host_lock, flags); 213 scb = list_first_entry_or_null(&wd->free_scbs, struct wd719x_scb, list); 214 if (scb) { 215 list_del(&scb->list); 216 phys = scb->phys; 217 } else { 218 spin_unlock_irqrestore(wd->sh->host_lock, flags); 219 scb = pci_alloc_consistent(wd->pdev, sizeof(struct wd719x_scb), 220 &phys); 221 spin_lock_irqsave(wd->sh->host_lock, flags); 222 if (!scb) { 223 dev_err(&wd->pdev->dev, "unable to allocate SCB\n"); 224 wd719x_finish_cmd(cmd, DID_ERROR); 225 spin_unlock_irqrestore(wd->sh->host_lock, flags); 226 return 0; 227 } 228 } 229 memset(scb, 0, sizeof(struct wd719x_scb)); 230 list_add(&scb->list, &wd->active_scbs); 231 232 scb->phys = phys; 233 scb->cmd = cmd; 234 cmd->host_scribble = (char *) scb; 235 236 scb->CDB_tag = 0; /* Tagged queueing not supported yet */ 237 scb->devid = cmd->device->id; 238 scb->lun = cmd->device->lun; 239 240 /* copy the command */ 241 memcpy(scb->CDB, cmd->cmnd, cmd->cmd_len); 242 243 /* map sense buffer */ 244 scb->sense_buf_length = SCSI_SENSE_BUFFERSIZE; 245 cmd->SCp.dma_handle = dma_map_single(&wd->pdev->dev, cmd->sense_buffer, 246 SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE); 247 scb->sense_buf = cpu_to_le32(cmd->SCp.dma_handle); 248 249 /* request autosense */ 250 scb->SCB_options |= WD719X_SCB_FLAGS_AUTO_REQUEST_SENSE; 251 252 /* check direction */ 253 if (cmd->sc_data_direction == DMA_TO_DEVICE) 254 scb->SCB_options |= WD719X_SCB_FLAGS_CHECK_DIRECTION 255 | WD719X_SCB_FLAGS_PCI_TO_SCSI; 256 else if (cmd->sc_data_direction == DMA_FROM_DEVICE) 257 scb->SCB_options |= WD719X_SCB_FLAGS_CHECK_DIRECTION; 258 259 /* Scather/gather */ 260 count_sg = scsi_dma_map(cmd); 261 if (count_sg < 0) { 262 wd719x_finish_cmd(cmd, DID_ERROR); 263 spin_unlock_irqrestore(wd->sh->host_lock, flags); 264 return 0; 265 } 266 BUG_ON(count_sg > WD719X_SG); 267 268 if (count_sg) { 269 struct scatterlist *sg; 270 271 scb->data_length = cpu_to_le32(count_sg * 272 sizeof(struct wd719x_sglist)); 273 scb->data_p = cpu_to_le32(scb->phys + 274 offsetof(struct wd719x_scb, sg_list)); 275 276 scsi_for_each_sg(cmd, sg, count_sg, i) { 277 scb->sg_list[i].ptr = cpu_to_le32(sg_dma_address(sg)); 278 scb->sg_list[i].length = cpu_to_le32(sg_dma_len(sg)); 279 } 280 scb->SCB_options |= WD719X_SCB_FLAGS_DO_SCATTER_GATHER; 281 } else { /* zero length */ 282 scb->data_length = 0; 283 scb->data_p = 0; 284 } 285 286 /* check if the Command register is free */ 287 if (wd719x_readb(wd, WD719X_AMR_COMMAND) != WD719X_CMD_READY) { 288 spin_unlock_irqrestore(wd->sh->host_lock, flags); 289 return SCSI_MLQUEUE_HOST_BUSY; 290 } 291 292 /* write pointer to the AMR */ 293 wd719x_writel(wd, WD719X_AMR_SCB_IN, scb->phys); 294 /* send SCB opcode */ 295 wd719x_writeb(wd, WD719X_AMR_COMMAND, WD719X_CMD_PROCESS_SCB); 296 297 spin_unlock_irqrestore(wd->sh->host_lock, flags); 298 299 return 0; 300 } 301 302 static int wd719x_chip_init(struct wd719x *wd) 303 { 304 int i, ret; 305 u32 risc_init[3]; 306 const struct firmware *fw_wcs, *fw_risc; 307 const char fwname_wcs[] = "wd719x-wcs.bin"; 308 const char fwname_risc[] = "wd719x-risc.bin"; 309 310 memset(wd->hash_virt, 0, WD719X_HASH_TABLE_SIZE); 311 312 /* WCS (sequencer) firmware */ 313 ret = request_firmware(&fw_wcs, fwname_wcs, &wd->pdev->dev); 314 if (ret) { 315 dev_err(&wd->pdev->dev, "Unable to load firmware %s: %d\n", 316 fwname_wcs, ret); 317 return ret; 318 } 319 /* RISC firmware */ 320 ret = request_firmware(&fw_risc, fwname_risc, &wd->pdev->dev); 321 if (ret) { 322 dev_err(&wd->pdev->dev, "Unable to load firmware %s: %d\n", 323 fwname_risc, ret); 324 release_firmware(fw_wcs); 325 return ret; 326 } 327 wd->fw_size = ALIGN(fw_wcs->size, 4) + fw_risc->size; 328 329 if (!wd->fw_virt) 330 wd->fw_virt = pci_alloc_consistent(wd->pdev, wd->fw_size, 331 &wd->fw_phys); 332 if (!wd->fw_virt) { 333 ret = -ENOMEM; 334 goto wd719x_init_end; 335 } 336 337 /* make a fresh copy of WCS and RISC code */ 338 memcpy(wd->fw_virt, fw_wcs->data, fw_wcs->size); 339 memcpy(wd->fw_virt + ALIGN(fw_wcs->size, 4), fw_risc->data, 340 fw_risc->size); 341 342 /* Reset the Spider Chip and adapter itself */ 343 wd719x_writeb(wd, WD719X_PCI_PORT_RESET, WD719X_PCI_RESET); 344 udelay(WD719X_WAIT_FOR_RISC); 345 /* Clear PIO mode bits set by BIOS */ 346 wd719x_writeb(wd, WD719X_AMR_CMD_PARAM, 0); 347 /* ensure RISC is not running */ 348 wd719x_writeb(wd, WD719X_PCI_MODE_SELECT, 0); 349 /* ensure command port is ready */ 350 wd719x_writeb(wd, WD719X_AMR_COMMAND, 0); 351 if (wd719x_wait_ready(wd)) { 352 ret = -ETIMEDOUT; 353 goto wd719x_init_end; 354 } 355 356 /* Transfer the first 2K words of RISC code to kick start the uP */ 357 risc_init[0] = wd->fw_phys; /* WCS FW */ 358 risc_init[1] = wd->fw_phys + ALIGN(fw_wcs->size, 4); /* RISC FW */ 359 risc_init[2] = wd->hash_phys; /* hash table */ 360 361 /* clear DMA status */ 362 wd719x_writeb(wd, WD719X_PCI_CHANNEL2_3STATUS, 0); 363 364 /* address to read firmware from */ 365 wd719x_writel(wd, WD719X_PCI_EXTERNAL_ADDR, risc_init[1]); 366 /* base address to write firmware to (on card) */ 367 wd719x_writew(wd, WD719X_PCI_INTERNAL_ADDR, WD719X_PRAM_BASE_ADDR); 368 /* size: first 2K words */ 369 wd719x_writew(wd, WD719X_PCI_DMA_TRANSFER_SIZE, 2048 * 2); 370 /* start DMA */ 371 wd719x_writeb(wd, WD719X_PCI_CHANNEL2_3CMD, WD719X_START_CHANNEL2_3DMA); 372 373 /* wait for DMA to complete */ 374 i = WD719X_WAIT_FOR_RISC; 375 while (i-- > 0) { 376 u8 status = wd719x_readb(wd, WD719X_PCI_CHANNEL2_3STATUS); 377 if (status == WD719X_START_CHANNEL2_3DONE) 378 break; 379 if (status == WD719X_START_CHANNEL2_3ABORT) { 380 dev_warn(&wd->pdev->dev, "RISC bootstrap failed: DMA aborted\n"); 381 ret = -EIO; 382 goto wd719x_init_end; 383 } 384 udelay(1); 385 } 386 if (i < 1) { 387 dev_warn(&wd->pdev->dev, "RISC bootstrap failed: DMA timeout\n"); 388 ret = -ETIMEDOUT; 389 goto wd719x_init_end; 390 } 391 392 /* firmware is loaded, now initialize and wake up the RISC */ 393 /* write RISC initialization long words to Spider */ 394 wd719x_writel(wd, WD719X_AMR_SCB_IN, risc_init[0]); 395 wd719x_writel(wd, WD719X_AMR_SCB_IN + 4, risc_init[1]); 396 wd719x_writel(wd, WD719X_AMR_SCB_IN + 8, risc_init[2]); 397 398 /* disable interrupts during initialization of RISC */ 399 wd719x_writeb(wd, WD719X_AMR_CMD_PARAM, WD719X_DISABLE_INT); 400 401 /* issue INITIALIZE RISC comand */ 402 wd719x_writeb(wd, WD719X_AMR_COMMAND, WD719X_CMD_INIT_RISC); 403 /* enable advanced mode (wake up RISC) */ 404 wd719x_writeb(wd, WD719X_PCI_MODE_SELECT, WD719X_ENABLE_ADVANCE_MODE); 405 udelay(WD719X_WAIT_FOR_RISC); 406 407 ret = wd719x_wait_done(wd, WD719X_WAIT_FOR_RISC); 408 /* clear interrupt status register */ 409 wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE); 410 if (ret) { 411 dev_warn(&wd->pdev->dev, "Unable to initialize RISC\n"); 412 goto wd719x_init_end; 413 } 414 /* RISC is up and running */ 415 416 /* Read FW version from RISC */ 417 ret = wd719x_direct_cmd(wd, WD719X_CMD_READ_FIRMVER, 0, 0, 0, 0, 418 WD719X_WAIT_FOR_RISC); 419 if (ret) { 420 dev_warn(&wd->pdev->dev, "Unable to read firmware version\n"); 421 goto wd719x_init_end; 422 } 423 dev_info(&wd->pdev->dev, "RISC initialized with firmware version %.2x.%.2x\n", 424 wd719x_readb(wd, WD719X_AMR_SCB_OUT + 1), 425 wd719x_readb(wd, WD719X_AMR_SCB_OUT)); 426 427 /* RESET SCSI bus */ 428 ret = wd719x_direct_cmd(wd, WD719X_CMD_BUSRESET, 0, 0, 0, 0, 429 WD719X_WAIT_FOR_SCSI_RESET); 430 if (ret) { 431 dev_warn(&wd->pdev->dev, "SCSI bus reset failed\n"); 432 goto wd719x_init_end; 433 } 434 435 /* use HostParameter structure to set Spider's Host Parameter Block */ 436 ret = wd719x_direct_cmd(wd, WD719X_CMD_SET_PARAM, 0, 437 sizeof(struct wd719x_host_param), 0, 438 wd->params_phys, WD719X_WAIT_FOR_RISC); 439 if (ret) { 440 dev_warn(&wd->pdev->dev, "Failed to set HOST PARAMETERS\n"); 441 goto wd719x_init_end; 442 } 443 444 /* initiate SCAM (does nothing if disabled in BIOS) */ 445 /* bug?: we should pass a mask of static IDs which we don't have */ 446 ret = wd719x_direct_cmd(wd, WD719X_CMD_INIT_SCAM, 0, 0, 0, 0, 447 WD719X_WAIT_FOR_SCSI_RESET); 448 if (ret) { 449 dev_warn(&wd->pdev->dev, "SCAM initialization failed\n"); 450 goto wd719x_init_end; 451 } 452 453 /* clear AMR_BIOS_SHARE_INT register */ 454 wd719x_writeb(wd, WD719X_AMR_BIOS_SHARE_INT, 0); 455 456 wd719x_init_end: 457 release_firmware(fw_wcs); 458 release_firmware(fw_risc); 459 460 return ret; 461 } 462 463 static int wd719x_abort(struct scsi_cmnd *cmd) 464 { 465 int action, result; 466 unsigned long flags; 467 struct wd719x_scb *scb = (struct wd719x_scb *)cmd->host_scribble; 468 struct wd719x *wd = shost_priv(cmd->device->host); 469 470 dev_info(&wd->pdev->dev, "abort command, tag: %x\n", cmd->tag); 471 472 action = /*cmd->tag ? WD719X_CMD_ABORT_TAG : */WD719X_CMD_ABORT; 473 474 spin_lock_irqsave(wd->sh->host_lock, flags); 475 result = wd719x_direct_cmd(wd, action, cmd->device->id, 476 cmd->device->lun, cmd->tag, scb->phys, 0); 477 spin_unlock_irqrestore(wd->sh->host_lock, flags); 478 if (result) 479 return FAILED; 480 481 return SUCCESS; 482 } 483 484 static int wd719x_reset(struct scsi_cmnd *cmd, u8 opcode, u8 device) 485 { 486 int result; 487 unsigned long flags; 488 struct wd719x *wd = shost_priv(cmd->device->host); 489 490 dev_info(&wd->pdev->dev, "%s reset requested\n", 491 (opcode == WD719X_CMD_BUSRESET) ? "bus" : "device"); 492 493 spin_lock_irqsave(wd->sh->host_lock, flags); 494 result = wd719x_direct_cmd(wd, opcode, device, 0, 0, 0, 495 WD719X_WAIT_FOR_SCSI_RESET); 496 spin_unlock_irqrestore(wd->sh->host_lock, flags); 497 if (result) 498 return FAILED; 499 500 return SUCCESS; 501 } 502 503 static int wd719x_dev_reset(struct scsi_cmnd *cmd) 504 { 505 return wd719x_reset(cmd, WD719X_CMD_RESET, cmd->device->id); 506 } 507 508 static int wd719x_bus_reset(struct scsi_cmnd *cmd) 509 { 510 return wd719x_reset(cmd, WD719X_CMD_BUSRESET, 0); 511 } 512 513 static int wd719x_host_reset(struct scsi_cmnd *cmd) 514 { 515 struct wd719x *wd = shost_priv(cmd->device->host); 516 struct wd719x_scb *scb, *tmp; 517 unsigned long flags; 518 int result; 519 520 dev_info(&wd->pdev->dev, "host reset requested\n"); 521 spin_lock_irqsave(wd->sh->host_lock, flags); 522 /* Try to reinit the RISC */ 523 if (wd719x_chip_init(wd) == 0) 524 result = SUCCESS; 525 else 526 result = FAILED; 527 528 /* flush all SCBs */ 529 list_for_each_entry_safe(scb, tmp, &wd->active_scbs, list) { 530 struct scsi_cmnd *tmp_cmd = scb->cmd; 531 wd719x_finish_cmd(tmp_cmd, result); 532 } 533 spin_unlock_irqrestore(wd->sh->host_lock, flags); 534 535 return result; 536 } 537 538 static int wd719x_biosparam(struct scsi_device *sdev, struct block_device *bdev, 539 sector_t capacity, int geom[]) 540 { 541 if (capacity >= 0x200000) { 542 geom[0] = 255; /* heads */ 543 geom[1] = 63; /* sectors */ 544 } else { 545 geom[0] = 64; /* heads */ 546 geom[1] = 32; /* sectors */ 547 } 548 geom[2] = sector_div(capacity, geom[0] * geom[1]); /* cylinders */ 549 550 return 0; 551 } 552 553 /* process a SCB-completion interrupt */ 554 static inline void wd719x_interrupt_SCB(struct wd719x *wd, 555 union wd719x_regs regs, 556 struct wd719x_scb *scb) 557 { 558 struct scsi_cmnd *cmd; 559 int result; 560 561 /* now have to find result from card */ 562 switch (regs.bytes.SUE) { 563 case WD719X_SUE_NOERRORS: 564 result = DID_OK; 565 break; 566 case WD719X_SUE_REJECTED: 567 dev_err(&wd->pdev->dev, "command rejected\n"); 568 result = DID_ERROR; 569 break; 570 case WD719X_SUE_SCBQFULL: 571 dev_err(&wd->pdev->dev, "SCB queue is full\n"); 572 result = DID_ERROR; 573 break; 574 case WD719X_SUE_TERM: 575 dev_dbg(&wd->pdev->dev, "SCB terminated by direct command\n"); 576 result = DID_ABORT; /* or DID_RESET? */ 577 break; 578 case WD719X_SUE_CHAN1ABORT: 579 case WD719X_SUE_CHAN23ABORT: 580 result = DID_ABORT; 581 dev_err(&wd->pdev->dev, "DMA abort\n"); 582 break; 583 case WD719X_SUE_CHAN1PAR: 584 case WD719X_SUE_CHAN23PAR: 585 result = DID_PARITY; 586 dev_err(&wd->pdev->dev, "DMA parity error\n"); 587 break; 588 case WD719X_SUE_TIMEOUT: 589 result = DID_TIME_OUT; 590 dev_dbg(&wd->pdev->dev, "selection timeout\n"); 591 break; 592 case WD719X_SUE_RESET: 593 dev_dbg(&wd->pdev->dev, "bus reset occurred\n"); 594 result = DID_RESET; 595 break; 596 case WD719X_SUE_BUSERROR: 597 dev_dbg(&wd->pdev->dev, "SCSI bus error\n"); 598 result = DID_ERROR; 599 break; 600 case WD719X_SUE_WRONGWAY: 601 dev_err(&wd->pdev->dev, "wrong data transfer direction\n"); 602 result = DID_ERROR; 603 break; 604 case WD719X_SUE_BADPHASE: 605 dev_err(&wd->pdev->dev, "invalid SCSI phase\n"); 606 result = DID_ERROR; 607 break; 608 case WD719X_SUE_TOOLONG: 609 dev_err(&wd->pdev->dev, "record too long\n"); 610 result = DID_ERROR; 611 break; 612 case WD719X_SUE_BUSFREE: 613 dev_err(&wd->pdev->dev, "unexpected bus free\n"); 614 result = DID_NO_CONNECT; /* or DID_ERROR ???*/ 615 break; 616 case WD719X_SUE_ARSDONE: 617 dev_dbg(&wd->pdev->dev, "auto request sense\n"); 618 if (regs.bytes.SCSI == 0) 619 result = DID_OK; 620 else 621 result = DID_PARITY; 622 break; 623 case WD719X_SUE_IGNORED: 624 dev_err(&wd->pdev->dev, "target id %d ignored command\n", 625 scb->cmd->device->id); 626 result = DID_NO_CONNECT; 627 break; 628 case WD719X_SUE_WRONGTAGS: 629 dev_err(&wd->pdev->dev, "reversed tags\n"); 630 result = DID_ERROR; 631 break; 632 case WD719X_SUE_BADTAGS: 633 dev_err(&wd->pdev->dev, "tag type not supported by target\n"); 634 result = DID_ERROR; 635 break; 636 case WD719X_SUE_NOSCAMID: 637 dev_err(&wd->pdev->dev, "no SCAM soft ID available\n"); 638 result = DID_ERROR; 639 break; 640 default: 641 dev_warn(&wd->pdev->dev, "unknown SUE error code: 0x%x\n", 642 regs.bytes.SUE); 643 result = DID_ERROR; 644 break; 645 } 646 cmd = scb->cmd; 647 648 wd719x_finish_cmd(cmd, result); 649 } 650 651 static irqreturn_t wd719x_interrupt(int irq, void *dev_id) 652 { 653 struct wd719x *wd = dev_id; 654 union wd719x_regs regs; 655 unsigned long flags; 656 u32 SCB_out; 657 658 spin_lock_irqsave(wd->sh->host_lock, flags); 659 /* read SCB pointer back from card */ 660 SCB_out = wd719x_readl(wd, WD719X_AMR_SCB_OUT); 661 /* read all status info at once */ 662 regs.all = cpu_to_le32(wd719x_readl(wd, WD719X_AMR_OP_CODE)); 663 664 switch (regs.bytes.INT) { 665 case WD719X_INT_NONE: 666 spin_unlock_irqrestore(wd->sh->host_lock, flags); 667 return IRQ_NONE; 668 case WD719X_INT_LINKNOSTATUS: 669 dev_err(&wd->pdev->dev, "linked command completed with no status\n"); 670 break; 671 case WD719X_INT_BADINT: 672 dev_err(&wd->pdev->dev, "unsolicited interrupt\n"); 673 break; 674 case WD719X_INT_NOERRORS: 675 case WD719X_INT_LINKNOERRORS: 676 case WD719X_INT_ERRORSLOGGED: 677 case WD719X_INT_SPIDERFAILED: 678 /* was the cmd completed a direct or SCB command? */ 679 if (regs.bytes.OPC == WD719X_CMD_PROCESS_SCB) { 680 struct wd719x_scb *scb; 681 list_for_each_entry(scb, &wd->active_scbs, list) 682 if (SCB_out == scb->phys) 683 break; 684 if (SCB_out == scb->phys) 685 wd719x_interrupt_SCB(wd, regs, scb); 686 else 687 dev_err(&wd->pdev->dev, "card returned invalid SCB pointer\n"); 688 } else 689 dev_warn(&wd->pdev->dev, "direct command 0x%x completed\n", 690 regs.bytes.OPC); 691 break; 692 case WD719X_INT_PIOREADY: 693 dev_err(&wd->pdev->dev, "card indicates PIO data ready but we never use PIO\n"); 694 /* interrupt will not be cleared until all data is read */ 695 break; 696 default: 697 dev_err(&wd->pdev->dev, "unknown interrupt reason: %d\n", 698 regs.bytes.INT); 699 700 } 701 /* clear interrupt so another can happen */ 702 wd719x_writeb(wd, WD719X_AMR_INT_STATUS, WD719X_INT_NONE); 703 spin_unlock_irqrestore(wd->sh->host_lock, flags); 704 705 return IRQ_HANDLED; 706 } 707 708 static void wd719x_eeprom_reg_read(struct eeprom_93cx6 *eeprom) 709 { 710 struct wd719x *wd = eeprom->data; 711 u8 reg = wd719x_readb(wd, WD719X_PCI_GPIO_DATA); 712 713 eeprom->reg_data_out = reg & WD719X_EE_DO; 714 } 715 716 static void wd719x_eeprom_reg_write(struct eeprom_93cx6 *eeprom) 717 { 718 struct wd719x *wd = eeprom->data; 719 u8 reg = 0; 720 721 if (eeprom->reg_data_in) 722 reg |= WD719X_EE_DI; 723 if (eeprom->reg_data_clock) 724 reg |= WD719X_EE_CLK; 725 if (eeprom->reg_chip_select) 726 reg |= WD719X_EE_CS; 727 728 wd719x_writeb(wd, WD719X_PCI_GPIO_DATA, reg); 729 } 730 731 /* read config from EEPROM so it can be downloaded by the RISC on (re-)init */ 732 static void wd719x_read_eeprom(struct wd719x *wd) 733 { 734 struct eeprom_93cx6 eeprom; 735 u8 gpio; 736 struct wd719x_eeprom_header header; 737 738 eeprom.data = wd; 739 eeprom.register_read = wd719x_eeprom_reg_read; 740 eeprom.register_write = wd719x_eeprom_reg_write; 741 eeprom.width = PCI_EEPROM_WIDTH_93C46; 742 743 /* set all outputs to low */ 744 wd719x_writeb(wd, WD719X_PCI_GPIO_DATA, 0); 745 /* configure GPIO pins */ 746 gpio = wd719x_readb(wd, WD719X_PCI_GPIO_CONTROL); 747 /* GPIO outputs */ 748 gpio &= (~(WD719X_EE_CLK | WD719X_EE_DI | WD719X_EE_CS)); 749 /* GPIO input */ 750 gpio |= WD719X_EE_DO; 751 wd719x_writeb(wd, WD719X_PCI_GPIO_CONTROL, gpio); 752 753 /* read EEPROM header */ 754 eeprom_93cx6_multireadb(&eeprom, 0, (u8 *)&header, sizeof(header)); 755 756 if (header.sig1 == 'W' && header.sig2 == 'D') 757 eeprom_93cx6_multireadb(&eeprom, header.cfg_offset, 758 (u8 *)wd->params, 759 sizeof(struct wd719x_host_param)); 760 else { /* default EEPROM values */ 761 dev_warn(&wd->pdev->dev, "EEPROM signature is invalid (0x%02x 0x%02x), using default values\n", 762 header.sig1, header.sig2); 763 wd->params->ch_1_th = 0x10; /* 16 DWs = 64 B */ 764 wd->params->scsi_conf = 0x4c; /* 48ma, spue, parity check */ 765 wd->params->own_scsi_id = 0x07; /* ID 7, SCAM disabled */ 766 wd->params->sel_timeout = 0x4d; /* 250 ms */ 767 wd->params->sleep_timer = 0x01; 768 wd->params->cdb_size = cpu_to_le16(0x5555); /* all 6 B */ 769 wd->params->scsi_pad = 0x1b; 770 if (wd->type == WD719X_TYPE_7193) /* narrow card - disable */ 771 wd->params->wide = cpu_to_le32(0x00000000); 772 else /* initiate & respond to WIDE messages */ 773 wd->params->wide = cpu_to_le32(0xffffffff); 774 wd->params->sync = cpu_to_le32(0xffffffff); 775 wd->params->soft_mask = 0x00; /* all disabled */ 776 wd->params->unsol_mask = 0x00; /* all disabled */ 777 } 778 /* disable TAGGED messages */ 779 wd->params->tag_en = cpu_to_le16(0x0000); 780 } 781 782 /* Read card type from GPIO bits 1 and 3 */ 783 static enum wd719x_card_type wd719x_detect_type(struct wd719x *wd) 784 { 785 u8 card = wd719x_readb(wd, WD719X_PCI_GPIO_CONTROL); 786 787 card |= WD719X_GPIO_ID_BITS; 788 wd719x_writeb(wd, WD719X_PCI_GPIO_CONTROL, card); 789 card = wd719x_readb(wd, WD719X_PCI_GPIO_DATA) & WD719X_GPIO_ID_BITS; 790 switch (card) { 791 case 0x08: 792 return WD719X_TYPE_7193; 793 case 0x02: 794 return WD719X_TYPE_7197; 795 case 0x00: 796 return WD719X_TYPE_7296; 797 default: 798 dev_warn(&wd->pdev->dev, "unknown card type 0x%x\n", card); 799 return WD719X_TYPE_UNKNOWN; 800 } 801 } 802 803 static int wd719x_board_found(struct Scsi_Host *sh) 804 { 805 struct wd719x *wd = shost_priv(sh); 806 static const char * const card_types[] = { 807 "Unknown card", "WD7193", "WD7197", "WD7296" 808 }; 809 int ret; 810 811 INIT_LIST_HEAD(&wd->active_scbs); 812 INIT_LIST_HEAD(&wd->free_scbs); 813 814 sh->base = pci_resource_start(wd->pdev, 0); 815 816 wd->type = wd719x_detect_type(wd); 817 818 wd->sh = sh; 819 sh->irq = wd->pdev->irq; 820 wd->fw_virt = NULL; 821 822 /* memory area for host (EEPROM) parameters */ 823 wd->params = pci_alloc_consistent(wd->pdev, 824 sizeof(struct wd719x_host_param), 825 &wd->params_phys); 826 if (!wd->params) { 827 dev_warn(&wd->pdev->dev, "unable to allocate parameter buffer\n"); 828 return -ENOMEM; 829 } 830 831 /* memory area for the RISC for hash table of outstanding requests */ 832 wd->hash_virt = pci_alloc_consistent(wd->pdev, WD719X_HASH_TABLE_SIZE, 833 &wd->hash_phys); 834 if (!wd->hash_virt) { 835 dev_warn(&wd->pdev->dev, "unable to allocate hash buffer\n"); 836 ret = -ENOMEM; 837 goto fail_free_params; 838 } 839 840 ret = request_irq(wd->pdev->irq, wd719x_interrupt, IRQF_SHARED, 841 "wd719x", wd); 842 if (ret) { 843 dev_warn(&wd->pdev->dev, "unable to assign IRQ %d\n", 844 wd->pdev->irq); 845 goto fail_free_hash; 846 } 847 848 /* read parameters from EEPROM */ 849 wd719x_read_eeprom(wd); 850 851 ret = wd719x_chip_init(wd); 852 if (ret) 853 goto fail_free_irq; 854 855 sh->this_id = wd->params->own_scsi_id & WD719X_EE_SCSI_ID_MASK; 856 857 dev_info(&wd->pdev->dev, "%s at I/O 0x%lx, IRQ %u, SCSI ID %d\n", 858 card_types[wd->type], sh->base, sh->irq, sh->this_id); 859 860 return 0; 861 862 fail_free_irq: 863 free_irq(wd->pdev->irq, wd); 864 fail_free_hash: 865 pci_free_consistent(wd->pdev, WD719X_HASH_TABLE_SIZE, wd->hash_virt, 866 wd->hash_phys); 867 fail_free_params: 868 pci_free_consistent(wd->pdev, sizeof(struct wd719x_host_param), 869 wd->params, wd->params_phys); 870 871 return ret; 872 } 873 874 static struct scsi_host_template wd719x_template = { 875 .module = THIS_MODULE, 876 .name = "Western Digital 719x", 877 .queuecommand = wd719x_queuecommand, 878 .eh_abort_handler = wd719x_abort, 879 .eh_device_reset_handler = wd719x_dev_reset, 880 .eh_bus_reset_handler = wd719x_bus_reset, 881 .eh_host_reset_handler = wd719x_host_reset, 882 .bios_param = wd719x_biosparam, 883 .proc_name = "wd719x", 884 .can_queue = 255, 885 .this_id = 7, 886 .sg_tablesize = WD719X_SG, 887 .use_clustering = ENABLE_CLUSTERING, 888 }; 889 890 static int wd719x_pci_probe(struct pci_dev *pdev, const struct pci_device_id *d) 891 { 892 int err; 893 struct Scsi_Host *sh; 894 struct wd719x *wd; 895 896 err = pci_enable_device(pdev); 897 if (err) 898 goto fail; 899 900 if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) { 901 dev_warn(&pdev->dev, "Unable to set 32-bit DMA mask\n"); 902 goto disable_device; 903 } 904 905 err = pci_request_regions(pdev, "wd719x"); 906 if (err) 907 goto disable_device; 908 pci_set_master(pdev); 909 910 err = -ENODEV; 911 if (pci_resource_len(pdev, 0) == 0) 912 goto release_region; 913 914 err = -ENOMEM; 915 sh = scsi_host_alloc(&wd719x_template, sizeof(struct wd719x)); 916 if (!sh) 917 goto release_region; 918 919 wd = shost_priv(sh); 920 wd->base = pci_iomap(pdev, 0, 0); 921 if (!wd->base) 922 goto free_host; 923 wd->pdev = pdev; 924 925 err = wd719x_board_found(sh); 926 if (err) 927 goto unmap; 928 929 err = scsi_add_host(sh, &wd->pdev->dev); 930 if (err) 931 goto destroy; 932 933 scsi_scan_host(sh); 934 935 pci_set_drvdata(pdev, sh); 936 return 0; 937 938 destroy: 939 wd719x_destroy(wd); 940 unmap: 941 pci_iounmap(pdev, wd->base); 942 free_host: 943 scsi_host_put(sh); 944 release_region: 945 pci_release_regions(pdev); 946 disable_device: 947 pci_disable_device(pdev); 948 fail: 949 return err; 950 } 951 952 953 static void wd719x_pci_remove(struct pci_dev *pdev) 954 { 955 struct Scsi_Host *sh = pci_get_drvdata(pdev); 956 struct wd719x *wd = shost_priv(sh); 957 958 scsi_remove_host(sh); 959 wd719x_destroy(wd); 960 pci_iounmap(pdev, wd->base); 961 pci_release_regions(pdev); 962 pci_disable_device(pdev); 963 964 scsi_host_put(sh); 965 } 966 967 static const struct pci_device_id wd719x_pci_table[] = { 968 { PCI_DEVICE(PCI_VENDOR_ID_WD, 0x3296) }, 969 {} 970 }; 971 972 MODULE_DEVICE_TABLE(pci, wd719x_pci_table); 973 974 static struct pci_driver wd719x_pci_driver = { 975 .name = "wd719x", 976 .id_table = wd719x_pci_table, 977 .probe = wd719x_pci_probe, 978 .remove = wd719x_pci_remove, 979 }; 980 981 module_pci_driver(wd719x_pci_driver); 982 983 MODULE_DESCRIPTION("Western Digital WD7193/7197/7296 SCSI driver"); 984 MODULE_AUTHOR("Ondrej Zary, Aaron Dewell, Juergen Gaertner"); 985 MODULE_LICENSE("GPL"); 986 MODULE_FIRMWARE("wd719x-wcs.bin"); 987 MODULE_FIRMWARE("wd719x-risc.bin"); 988