1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * scsi_scan.c 4 * 5 * Copyright (C) 2000 Eric Youngdale, 6 * Copyright (C) 2002 Patrick Mansfield 7 * 8 * The general scanning/probing algorithm is as follows, exceptions are 9 * made to it depending on device specific flags, compilation options, and 10 * global variable (boot or module load time) settings. 11 * 12 * A specific LUN is scanned via an INQUIRY command; if the LUN has a 13 * device attached, a scsi_device is allocated and setup for it. 14 * 15 * For every id of every channel on the given host: 16 * 17 * Scan LUN 0; if the target responds to LUN 0 (even if there is no 18 * device or storage attached to LUN 0): 19 * 20 * If LUN 0 has a device attached, allocate and setup a 21 * scsi_device for it. 22 * 23 * If target is SCSI-3 or up, issue a REPORT LUN, and scan 24 * all of the LUNs returned by the REPORT LUN; else, 25 * sequentially scan LUNs up until some maximum is reached, 26 * or a LUN is seen that cannot have a device attached to it. 27 */ 28 29 #include <linux/module.h> 30 #include <linux/moduleparam.h> 31 #include <linux/init.h> 32 #include <linux/blkdev.h> 33 #include <linux/delay.h> 34 #include <linux/kthread.h> 35 #include <linux/spinlock.h> 36 #include <linux/async.h> 37 #include <linux/slab.h> 38 #include <asm/unaligned.h> 39 40 #include <scsi/scsi.h> 41 #include <scsi/scsi_cmnd.h> 42 #include <scsi/scsi_device.h> 43 #include <scsi/scsi_driver.h> 44 #include <scsi/scsi_devinfo.h> 45 #include <scsi/scsi_host.h> 46 #include <scsi/scsi_transport.h> 47 #include <scsi/scsi_dh.h> 48 #include <scsi/scsi_eh.h> 49 50 #include "scsi_priv.h" 51 #include "scsi_logging.h" 52 53 #define ALLOC_FAILURE_MSG KERN_ERR "%s: Allocation failure during" \ 54 " SCSI scanning, some SCSI devices might not be configured\n" 55 56 /* 57 * Default timeout 58 */ 59 #define SCSI_TIMEOUT (2*HZ) 60 #define SCSI_REPORT_LUNS_TIMEOUT (30*HZ) 61 62 /* 63 * Prefix values for the SCSI id's (stored in sysfs name field) 64 */ 65 #define SCSI_UID_SER_NUM 'S' 66 #define SCSI_UID_UNKNOWN 'Z' 67 68 /* 69 * Return values of some of the scanning functions. 70 * 71 * SCSI_SCAN_NO_RESPONSE: no valid response received from the target, this 72 * includes allocation or general failures preventing IO from being sent. 73 * 74 * SCSI_SCAN_TARGET_PRESENT: target responded, but no device is available 75 * on the given LUN. 76 * 77 * SCSI_SCAN_LUN_PRESENT: target responded, and a device is available on a 78 * given LUN. 79 */ 80 #define SCSI_SCAN_NO_RESPONSE 0 81 #define SCSI_SCAN_TARGET_PRESENT 1 82 #define SCSI_SCAN_LUN_PRESENT 2 83 84 static const char *scsi_null_device_strs = "nullnullnullnull"; 85 86 #define MAX_SCSI_LUNS 512 87 88 static u64 max_scsi_luns = MAX_SCSI_LUNS; 89 90 module_param_named(max_luns, max_scsi_luns, ullong, S_IRUGO|S_IWUSR); 91 MODULE_PARM_DESC(max_luns, 92 "last scsi LUN (should be between 1 and 2^64-1)"); 93 94 #ifdef CONFIG_SCSI_SCAN_ASYNC 95 #define SCSI_SCAN_TYPE_DEFAULT "async" 96 #else 97 #define SCSI_SCAN_TYPE_DEFAULT "sync" 98 #endif 99 100 static char scsi_scan_type[7] = SCSI_SCAN_TYPE_DEFAULT; 101 102 module_param_string(scan, scsi_scan_type, sizeof(scsi_scan_type), 103 S_IRUGO|S_IWUSR); 104 MODULE_PARM_DESC(scan, "sync, async, manual, or none. " 105 "Setting to 'manual' disables automatic scanning, but allows " 106 "for manual device scan via the 'scan' sysfs attribute."); 107 108 static unsigned int scsi_inq_timeout = SCSI_TIMEOUT/HZ + 18; 109 110 module_param_named(inq_timeout, scsi_inq_timeout, uint, S_IRUGO|S_IWUSR); 111 MODULE_PARM_DESC(inq_timeout, 112 "Timeout (in seconds) waiting for devices to answer INQUIRY." 113 " Default is 20. Some devices may need more; most need less."); 114 115 /* This lock protects only this list */ 116 static DEFINE_SPINLOCK(async_scan_lock); 117 static LIST_HEAD(scanning_hosts); 118 119 struct async_scan_data { 120 struct list_head list; 121 struct Scsi_Host *shost; 122 struct completion prev_finished; 123 }; 124 125 /* 126 * scsi_enable_async_suspend - Enable async suspend and resume 127 */ 128 void scsi_enable_async_suspend(struct device *dev) 129 { 130 /* 131 * If a user has disabled async probing a likely reason is due to a 132 * storage enclosure that does not inject staggered spin-ups. For 133 * safety, make resume synchronous as well in that case. 134 */ 135 if (strncmp(scsi_scan_type, "async", 5) != 0) 136 return; 137 /* Enable asynchronous suspend and resume. */ 138 device_enable_async_suspend(dev); 139 } 140 141 /** 142 * scsi_complete_async_scans - Wait for asynchronous scans to complete 143 * 144 * When this function returns, any host which started scanning before 145 * this function was called will have finished its scan. Hosts which 146 * started scanning after this function was called may or may not have 147 * finished. 148 */ 149 int scsi_complete_async_scans(void) 150 { 151 struct async_scan_data *data; 152 153 do { 154 if (list_empty(&scanning_hosts)) 155 return 0; 156 /* If we can't get memory immediately, that's OK. Just 157 * sleep a little. Even if we never get memory, the async 158 * scans will finish eventually. 159 */ 160 data = kmalloc(sizeof(*data), GFP_KERNEL); 161 if (!data) 162 msleep(1); 163 } while (!data); 164 165 data->shost = NULL; 166 init_completion(&data->prev_finished); 167 168 spin_lock(&async_scan_lock); 169 /* Check that there's still somebody else on the list */ 170 if (list_empty(&scanning_hosts)) 171 goto done; 172 list_add_tail(&data->list, &scanning_hosts); 173 spin_unlock(&async_scan_lock); 174 175 printk(KERN_INFO "scsi: waiting for bus probes to complete ...\n"); 176 wait_for_completion(&data->prev_finished); 177 178 spin_lock(&async_scan_lock); 179 list_del(&data->list); 180 if (!list_empty(&scanning_hosts)) { 181 struct async_scan_data *next = list_entry(scanning_hosts.next, 182 struct async_scan_data, list); 183 complete(&next->prev_finished); 184 } 185 done: 186 spin_unlock(&async_scan_lock); 187 188 kfree(data); 189 return 0; 190 } 191 192 /** 193 * scsi_unlock_floptical - unlock device via a special MODE SENSE command 194 * @sdev: scsi device to send command to 195 * @result: area to store the result of the MODE SENSE 196 * 197 * Description: 198 * Send a vendor specific MODE SENSE (not a MODE SELECT) command. 199 * Called for BLIST_KEY devices. 200 **/ 201 static void scsi_unlock_floptical(struct scsi_device *sdev, 202 unsigned char *result) 203 { 204 unsigned char scsi_cmd[MAX_COMMAND_SIZE]; 205 206 sdev_printk(KERN_NOTICE, sdev, "unlocking floptical drive\n"); 207 scsi_cmd[0] = MODE_SENSE; 208 scsi_cmd[1] = 0; 209 scsi_cmd[2] = 0x2e; 210 scsi_cmd[3] = 0; 211 scsi_cmd[4] = 0x2a; /* size */ 212 scsi_cmd[5] = 0; 213 scsi_execute_req(sdev, scsi_cmd, DMA_FROM_DEVICE, result, 0x2a, NULL, 214 SCSI_TIMEOUT, 3, NULL); 215 } 216 217 static int scsi_realloc_sdev_budget_map(struct scsi_device *sdev, 218 unsigned int depth) 219 { 220 int new_shift = sbitmap_calculate_shift(depth); 221 bool need_alloc = !sdev->budget_map.map; 222 bool need_free = false; 223 int ret; 224 struct sbitmap sb_backup; 225 226 depth = min_t(unsigned int, depth, scsi_device_max_queue_depth(sdev)); 227 228 /* 229 * realloc if new shift is calculated, which is caused by setting 230 * up one new default queue depth after calling ->slave_configure 231 */ 232 if (!need_alloc && new_shift != sdev->budget_map.shift) 233 need_alloc = need_free = true; 234 235 if (!need_alloc) 236 return 0; 237 238 /* 239 * Request queue has to be frozen for reallocating budget map, 240 * and here disk isn't added yet, so freezing is pretty fast 241 */ 242 if (need_free) { 243 blk_mq_freeze_queue(sdev->request_queue); 244 sb_backup = sdev->budget_map; 245 } 246 ret = sbitmap_init_node(&sdev->budget_map, 247 scsi_device_max_queue_depth(sdev), 248 new_shift, GFP_KERNEL, 249 sdev->request_queue->node, false, true); 250 if (!ret) 251 sbitmap_resize(&sdev->budget_map, depth); 252 253 if (need_free) { 254 if (ret) 255 sdev->budget_map = sb_backup; 256 else 257 sbitmap_free(&sb_backup); 258 ret = 0; 259 blk_mq_unfreeze_queue(sdev->request_queue); 260 } 261 return ret; 262 } 263 264 /** 265 * scsi_alloc_sdev - allocate and setup a scsi_Device 266 * @starget: which target to allocate a &scsi_device for 267 * @lun: which lun 268 * @hostdata: usually NULL and set by ->slave_alloc instead 269 * 270 * Description: 271 * Allocate, initialize for io, and return a pointer to a scsi_Device. 272 * Stores the @shost, @channel, @id, and @lun in the scsi_Device, and 273 * adds scsi_Device to the appropriate list. 274 * 275 * Return value: 276 * scsi_Device pointer, or NULL on failure. 277 **/ 278 static struct scsi_device *scsi_alloc_sdev(struct scsi_target *starget, 279 u64 lun, void *hostdata) 280 { 281 unsigned int depth; 282 struct scsi_device *sdev; 283 struct request_queue *q; 284 int display_failure_msg = 1, ret; 285 struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); 286 287 sdev = kzalloc(sizeof(*sdev) + shost->transportt->device_size, 288 GFP_KERNEL); 289 if (!sdev) 290 goto out; 291 292 sdev->vendor = scsi_null_device_strs; 293 sdev->model = scsi_null_device_strs; 294 sdev->rev = scsi_null_device_strs; 295 sdev->host = shost; 296 sdev->queue_ramp_up_period = SCSI_DEFAULT_RAMP_UP_PERIOD; 297 sdev->id = starget->id; 298 sdev->lun = lun; 299 sdev->channel = starget->channel; 300 mutex_init(&sdev->state_mutex); 301 sdev->sdev_state = SDEV_CREATED; 302 INIT_LIST_HEAD(&sdev->siblings); 303 INIT_LIST_HEAD(&sdev->same_target_siblings); 304 INIT_LIST_HEAD(&sdev->starved_entry); 305 INIT_LIST_HEAD(&sdev->event_list); 306 spin_lock_init(&sdev->list_lock); 307 mutex_init(&sdev->inquiry_mutex); 308 INIT_WORK(&sdev->event_work, scsi_evt_thread); 309 INIT_WORK(&sdev->requeue_work, scsi_requeue_run_queue); 310 311 sdev->sdev_gendev.parent = get_device(&starget->dev); 312 sdev->sdev_target = starget; 313 314 /* usually NULL and set by ->slave_alloc instead */ 315 sdev->hostdata = hostdata; 316 317 /* if the device needs this changing, it may do so in the 318 * slave_configure function */ 319 sdev->max_device_blocked = SCSI_DEFAULT_DEVICE_BLOCKED; 320 321 /* 322 * Some low level driver could use device->type 323 */ 324 sdev->type = -1; 325 326 /* 327 * Assume that the device will have handshaking problems, 328 * and then fix this field later if it turns out it 329 * doesn't 330 */ 331 sdev->borken = 1; 332 333 sdev->sg_reserved_size = INT_MAX; 334 335 q = blk_mq_init_queue(&sdev->host->tag_set); 336 if (IS_ERR(q)) { 337 /* release fn is set up in scsi_sysfs_device_initialise, so 338 * have to free and put manually here */ 339 put_device(&starget->dev); 340 kfree(sdev); 341 goto out; 342 } 343 sdev->request_queue = q; 344 q->queuedata = sdev; 345 __scsi_init_queue(sdev->host, q); 346 WARN_ON_ONCE(!blk_get_queue(q)); 347 348 depth = sdev->host->cmd_per_lun ?: 1; 349 350 /* 351 * Use .can_queue as budget map's depth because we have to 352 * support adjusting queue depth from sysfs. Meantime use 353 * default device queue depth to figure out sbitmap shift 354 * since we use this queue depth most of times. 355 */ 356 if (scsi_realloc_sdev_budget_map(sdev, depth)) { 357 put_device(&starget->dev); 358 kfree(sdev); 359 goto out; 360 } 361 362 scsi_change_queue_depth(sdev, depth); 363 364 scsi_sysfs_device_initialize(sdev); 365 366 if (shost->hostt->slave_alloc) { 367 ret = shost->hostt->slave_alloc(sdev); 368 if (ret) { 369 /* 370 * if LLDD reports slave not present, don't clutter 371 * console with alloc failure messages 372 */ 373 if (ret == -ENXIO) 374 display_failure_msg = 0; 375 goto out_device_destroy; 376 } 377 } 378 379 return sdev; 380 381 out_device_destroy: 382 __scsi_remove_device(sdev); 383 out: 384 if (display_failure_msg) 385 printk(ALLOC_FAILURE_MSG, __func__); 386 return NULL; 387 } 388 389 static void scsi_target_destroy(struct scsi_target *starget) 390 { 391 struct device *dev = &starget->dev; 392 struct Scsi_Host *shost = dev_to_shost(dev->parent); 393 unsigned long flags; 394 395 BUG_ON(starget->state == STARGET_DEL); 396 starget->state = STARGET_DEL; 397 transport_destroy_device(dev); 398 spin_lock_irqsave(shost->host_lock, flags); 399 if (shost->hostt->target_destroy) 400 shost->hostt->target_destroy(starget); 401 list_del_init(&starget->siblings); 402 spin_unlock_irqrestore(shost->host_lock, flags); 403 put_device(dev); 404 } 405 406 static void scsi_target_dev_release(struct device *dev) 407 { 408 struct device *parent = dev->parent; 409 struct Scsi_Host *shost = dev_to_shost(parent); 410 struct scsi_target *starget = to_scsi_target(dev); 411 412 kfree(starget); 413 414 if (atomic_dec_return(&shost->target_count) == 0) 415 wake_up(&shost->targets_wq); 416 417 put_device(parent); 418 } 419 420 static struct device_type scsi_target_type = { 421 .name = "scsi_target", 422 .release = scsi_target_dev_release, 423 }; 424 425 int scsi_is_target_device(const struct device *dev) 426 { 427 return dev->type == &scsi_target_type; 428 } 429 EXPORT_SYMBOL(scsi_is_target_device); 430 431 static struct scsi_target *__scsi_find_target(struct device *parent, 432 int channel, uint id) 433 { 434 struct scsi_target *starget, *found_starget = NULL; 435 struct Scsi_Host *shost = dev_to_shost(parent); 436 /* 437 * Search for an existing target for this sdev. 438 */ 439 list_for_each_entry(starget, &shost->__targets, siblings) { 440 if (starget->id == id && 441 starget->channel == channel) { 442 found_starget = starget; 443 break; 444 } 445 } 446 if (found_starget) 447 get_device(&found_starget->dev); 448 449 return found_starget; 450 } 451 452 /** 453 * scsi_target_reap_ref_release - remove target from visibility 454 * @kref: the reap_ref in the target being released 455 * 456 * Called on last put of reap_ref, which is the indication that no device 457 * under this target is visible anymore, so render the target invisible in 458 * sysfs. Note: we have to be in user context here because the target reaps 459 * should be done in places where the scsi device visibility is being removed. 460 */ 461 static void scsi_target_reap_ref_release(struct kref *kref) 462 { 463 struct scsi_target *starget 464 = container_of(kref, struct scsi_target, reap_ref); 465 466 /* 467 * if we get here and the target is still in a CREATED state that 468 * means it was allocated but never made visible (because a scan 469 * turned up no LUNs), so don't call device_del() on it. 470 */ 471 if ((starget->state != STARGET_CREATED) && 472 (starget->state != STARGET_CREATED_REMOVE)) { 473 transport_remove_device(&starget->dev); 474 device_del(&starget->dev); 475 } 476 scsi_target_destroy(starget); 477 } 478 479 static void scsi_target_reap_ref_put(struct scsi_target *starget) 480 { 481 kref_put(&starget->reap_ref, scsi_target_reap_ref_release); 482 } 483 484 /** 485 * scsi_alloc_target - allocate a new or find an existing target 486 * @parent: parent of the target (need not be a scsi host) 487 * @channel: target channel number (zero if no channels) 488 * @id: target id number 489 * 490 * Return an existing target if one exists, provided it hasn't already 491 * gone into STARGET_DEL state, otherwise allocate a new target. 492 * 493 * The target is returned with an incremented reference, so the caller 494 * is responsible for both reaping and doing a last put 495 */ 496 static struct scsi_target *scsi_alloc_target(struct device *parent, 497 int channel, uint id) 498 { 499 struct Scsi_Host *shost = dev_to_shost(parent); 500 struct device *dev = NULL; 501 unsigned long flags; 502 const int size = sizeof(struct scsi_target) 503 + shost->transportt->target_size; 504 struct scsi_target *starget; 505 struct scsi_target *found_target; 506 int error, ref_got; 507 508 starget = kzalloc(size, GFP_KERNEL); 509 if (!starget) { 510 printk(KERN_ERR "%s: allocation failure\n", __func__); 511 return NULL; 512 } 513 dev = &starget->dev; 514 device_initialize(dev); 515 kref_init(&starget->reap_ref); 516 dev->parent = get_device(parent); 517 dev_set_name(dev, "target%d:%d:%d", shost->host_no, channel, id); 518 dev->bus = &scsi_bus_type; 519 dev->type = &scsi_target_type; 520 scsi_enable_async_suspend(dev); 521 starget->id = id; 522 starget->channel = channel; 523 starget->can_queue = 0; 524 INIT_LIST_HEAD(&starget->siblings); 525 INIT_LIST_HEAD(&starget->devices); 526 starget->state = STARGET_CREATED; 527 starget->scsi_level = SCSI_2; 528 starget->max_target_blocked = SCSI_DEFAULT_TARGET_BLOCKED; 529 init_waitqueue_head(&starget->sdev_wq); 530 531 atomic_inc(&shost->target_count); 532 533 retry: 534 spin_lock_irqsave(shost->host_lock, flags); 535 536 found_target = __scsi_find_target(parent, channel, id); 537 if (found_target) 538 goto found; 539 540 list_add_tail(&starget->siblings, &shost->__targets); 541 spin_unlock_irqrestore(shost->host_lock, flags); 542 /* allocate and add */ 543 transport_setup_device(dev); 544 if (shost->hostt->target_alloc) { 545 error = shost->hostt->target_alloc(starget); 546 547 if(error) { 548 if (error != -ENXIO) 549 dev_err(dev, "target allocation failed, error %d\n", error); 550 /* don't want scsi_target_reap to do the final 551 * put because it will be under the host lock */ 552 scsi_target_destroy(starget); 553 return NULL; 554 } 555 } 556 get_device(dev); 557 558 return starget; 559 560 found: 561 /* 562 * release routine already fired if kref is zero, so if we can still 563 * take the reference, the target must be alive. If we can't, it must 564 * be dying and we need to wait for a new target 565 */ 566 ref_got = kref_get_unless_zero(&found_target->reap_ref); 567 568 spin_unlock_irqrestore(shost->host_lock, flags); 569 if (ref_got) { 570 put_device(dev); 571 return found_target; 572 } 573 /* 574 * Unfortunately, we found a dying target; need to wait until it's 575 * dead before we can get a new one. There is an anomaly here. We 576 * *should* call scsi_target_reap() to balance the kref_get() of the 577 * reap_ref above. However, since the target being released, it's 578 * already invisible and the reap_ref is irrelevant. If we call 579 * scsi_target_reap() we might spuriously do another device_del() on 580 * an already invisible target. 581 */ 582 put_device(&found_target->dev); 583 /* 584 * length of time is irrelevant here, we just want to yield the CPU 585 * for a tick to avoid busy waiting for the target to die. 586 */ 587 msleep(1); 588 goto retry; 589 } 590 591 /** 592 * scsi_target_reap - check to see if target is in use and destroy if not 593 * @starget: target to be checked 594 * 595 * This is used after removing a LUN or doing a last put of the target 596 * it checks atomically that nothing is using the target and removes 597 * it if so. 598 */ 599 void scsi_target_reap(struct scsi_target *starget) 600 { 601 /* 602 * serious problem if this triggers: STARGET_DEL is only set in the if 603 * the reap_ref drops to zero, so we're trying to do another final put 604 * on an already released kref 605 */ 606 BUG_ON(starget->state == STARGET_DEL); 607 scsi_target_reap_ref_put(starget); 608 } 609 610 /** 611 * scsi_sanitize_inquiry_string - remove non-graphical chars from an 612 * INQUIRY result string 613 * @s: INQUIRY result string to sanitize 614 * @len: length of the string 615 * 616 * Description: 617 * The SCSI spec says that INQUIRY vendor, product, and revision 618 * strings must consist entirely of graphic ASCII characters, 619 * padded on the right with spaces. Since not all devices obey 620 * this rule, we will replace non-graphic or non-ASCII characters 621 * with spaces. Exception: a NUL character is interpreted as a 622 * string terminator, so all the following characters are set to 623 * spaces. 624 **/ 625 void scsi_sanitize_inquiry_string(unsigned char *s, int len) 626 { 627 int terminated = 0; 628 629 for (; len > 0; (--len, ++s)) { 630 if (*s == 0) 631 terminated = 1; 632 if (terminated || *s < 0x20 || *s > 0x7e) 633 *s = ' '; 634 } 635 } 636 EXPORT_SYMBOL(scsi_sanitize_inquiry_string); 637 638 /** 639 * scsi_probe_lun - probe a single LUN using a SCSI INQUIRY 640 * @sdev: scsi_device to probe 641 * @inq_result: area to store the INQUIRY result 642 * @result_len: len of inq_result 643 * @bflags: store any bflags found here 644 * 645 * Description: 646 * Probe the lun associated with @req using a standard SCSI INQUIRY; 647 * 648 * If the INQUIRY is successful, zero is returned and the 649 * INQUIRY data is in @inq_result; the scsi_level and INQUIRY length 650 * are copied to the scsi_device any flags value is stored in *@bflags. 651 **/ 652 static int scsi_probe_lun(struct scsi_device *sdev, unsigned char *inq_result, 653 int result_len, blist_flags_t *bflags) 654 { 655 unsigned char scsi_cmd[MAX_COMMAND_SIZE]; 656 int first_inquiry_len, try_inquiry_len, next_inquiry_len; 657 int response_len = 0; 658 int pass, count, result; 659 struct scsi_sense_hdr sshdr; 660 661 *bflags = 0; 662 663 /* Perform up to 3 passes. The first pass uses a conservative 664 * transfer length of 36 unless sdev->inquiry_len specifies a 665 * different value. */ 666 first_inquiry_len = sdev->inquiry_len ? sdev->inquiry_len : 36; 667 try_inquiry_len = first_inquiry_len; 668 pass = 1; 669 670 next_pass: 671 SCSI_LOG_SCAN_BUS(3, sdev_printk(KERN_INFO, sdev, 672 "scsi scan: INQUIRY pass %d length %d\n", 673 pass, try_inquiry_len)); 674 675 /* Each pass gets up to three chances to ignore Unit Attention */ 676 for (count = 0; count < 3; ++count) { 677 int resid; 678 679 memset(scsi_cmd, 0, 6); 680 scsi_cmd[0] = INQUIRY; 681 scsi_cmd[4] = (unsigned char) try_inquiry_len; 682 683 memset(inq_result, 0, try_inquiry_len); 684 685 result = scsi_execute_req(sdev, scsi_cmd, DMA_FROM_DEVICE, 686 inq_result, try_inquiry_len, &sshdr, 687 HZ / 2 + HZ * scsi_inq_timeout, 3, 688 &resid); 689 690 SCSI_LOG_SCAN_BUS(3, sdev_printk(KERN_INFO, sdev, 691 "scsi scan: INQUIRY %s with code 0x%x\n", 692 result ? "failed" : "successful", result)); 693 694 if (result > 0) { 695 /* 696 * not-ready to ready transition [asc/ascq=0x28/0x0] 697 * or power-on, reset [asc/ascq=0x29/0x0], continue. 698 * INQUIRY should not yield UNIT_ATTENTION 699 * but many buggy devices do so anyway. 700 */ 701 if (scsi_status_is_check_condition(result) && 702 scsi_sense_valid(&sshdr)) { 703 if ((sshdr.sense_key == UNIT_ATTENTION) && 704 ((sshdr.asc == 0x28) || 705 (sshdr.asc == 0x29)) && 706 (sshdr.ascq == 0)) 707 continue; 708 } 709 } else if (result == 0) { 710 /* 711 * if nothing was transferred, we try 712 * again. It's a workaround for some USB 713 * devices. 714 */ 715 if (resid == try_inquiry_len) 716 continue; 717 } 718 break; 719 } 720 721 if (result == 0) { 722 scsi_sanitize_inquiry_string(&inq_result[8], 8); 723 scsi_sanitize_inquiry_string(&inq_result[16], 16); 724 scsi_sanitize_inquiry_string(&inq_result[32], 4); 725 726 response_len = inq_result[4] + 5; 727 if (response_len > 255) 728 response_len = first_inquiry_len; /* sanity */ 729 730 /* 731 * Get any flags for this device. 732 * 733 * XXX add a bflags to scsi_device, and replace the 734 * corresponding bit fields in scsi_device, so bflags 735 * need not be passed as an argument. 736 */ 737 *bflags = scsi_get_device_flags(sdev, &inq_result[8], 738 &inq_result[16]); 739 740 /* When the first pass succeeds we gain information about 741 * what larger transfer lengths might work. */ 742 if (pass == 1) { 743 if (BLIST_INQUIRY_36 & *bflags) 744 next_inquiry_len = 36; 745 /* 746 * LLD specified a maximum sdev->inquiry_len 747 * but device claims it has more data. Capping 748 * the length only makes sense for legacy 749 * devices. If a device supports SPC-4 (2014) 750 * or newer, assume that it is safe to ask for 751 * as much as the device says it supports. 752 */ 753 else if (sdev->inquiry_len && 754 response_len > sdev->inquiry_len && 755 (inq_result[2] & 0x7) < 6) /* SPC-4 */ 756 next_inquiry_len = sdev->inquiry_len; 757 else 758 next_inquiry_len = response_len; 759 760 /* If more data is available perform the second pass */ 761 if (next_inquiry_len > try_inquiry_len) { 762 try_inquiry_len = next_inquiry_len; 763 pass = 2; 764 goto next_pass; 765 } 766 } 767 768 } else if (pass == 2) { 769 sdev_printk(KERN_INFO, sdev, 770 "scsi scan: %d byte inquiry failed. " 771 "Consider BLIST_INQUIRY_36 for this device\n", 772 try_inquiry_len); 773 774 /* If this pass failed, the third pass goes back and transfers 775 * the same amount as we successfully got in the first pass. */ 776 try_inquiry_len = first_inquiry_len; 777 pass = 3; 778 goto next_pass; 779 } 780 781 /* If the last transfer attempt got an error, assume the 782 * peripheral doesn't exist or is dead. */ 783 if (result) 784 return -EIO; 785 786 /* Don't report any more data than the device says is valid */ 787 sdev->inquiry_len = min(try_inquiry_len, response_len); 788 789 /* 790 * XXX Abort if the response length is less than 36? If less than 791 * 32, the lookup of the device flags (above) could be invalid, 792 * and it would be possible to take an incorrect action - we do 793 * not want to hang because of a short INQUIRY. On the flip side, 794 * if the device is spun down or becoming ready (and so it gives a 795 * short INQUIRY), an abort here prevents any further use of the 796 * device, including spin up. 797 * 798 * On the whole, the best approach seems to be to assume the first 799 * 36 bytes are valid no matter what the device says. That's 800 * better than copying < 36 bytes to the inquiry-result buffer 801 * and displaying garbage for the Vendor, Product, or Revision 802 * strings. 803 */ 804 if (sdev->inquiry_len < 36) { 805 if (!sdev->host->short_inquiry) { 806 shost_printk(KERN_INFO, sdev->host, 807 "scsi scan: INQUIRY result too short (%d)," 808 " using 36\n", sdev->inquiry_len); 809 sdev->host->short_inquiry = 1; 810 } 811 sdev->inquiry_len = 36; 812 } 813 814 /* 815 * Related to the above issue: 816 * 817 * XXX Devices (disk or all?) should be sent a TEST UNIT READY, 818 * and if not ready, sent a START_STOP to start (maybe spin up) and 819 * then send the INQUIRY again, since the INQUIRY can change after 820 * a device is initialized. 821 * 822 * Ideally, start a device if explicitly asked to do so. This 823 * assumes that a device is spun up on power on, spun down on 824 * request, and then spun up on request. 825 */ 826 827 /* 828 * The scanning code needs to know the scsi_level, even if no 829 * device is attached at LUN 0 (SCSI_SCAN_TARGET_PRESENT) so 830 * non-zero LUNs can be scanned. 831 */ 832 sdev->scsi_level = inq_result[2] & 0x07; 833 if (sdev->scsi_level >= 2 || 834 (sdev->scsi_level == 1 && (inq_result[3] & 0x0f) == 1)) 835 sdev->scsi_level++; 836 sdev->sdev_target->scsi_level = sdev->scsi_level; 837 838 /* 839 * If SCSI-2 or lower, and if the transport requires it, 840 * store the LUN value in CDB[1]. 841 */ 842 sdev->lun_in_cdb = 0; 843 if (sdev->scsi_level <= SCSI_2 && 844 sdev->scsi_level != SCSI_UNKNOWN && 845 !sdev->host->no_scsi2_lun_in_cdb) 846 sdev->lun_in_cdb = 1; 847 848 return 0; 849 } 850 851 /** 852 * scsi_add_lun - allocate and fully initialze a scsi_device 853 * @sdev: holds information to be stored in the new scsi_device 854 * @inq_result: holds the result of a previous INQUIRY to the LUN 855 * @bflags: black/white list flag 856 * @async: 1 if this device is being scanned asynchronously 857 * 858 * Description: 859 * Initialize the scsi_device @sdev. Optionally set fields based 860 * on values in *@bflags. 861 * 862 * Return: 863 * SCSI_SCAN_NO_RESPONSE: could not allocate or setup a scsi_device 864 * SCSI_SCAN_LUN_PRESENT: a new scsi_device was allocated and initialized 865 **/ 866 static int scsi_add_lun(struct scsi_device *sdev, unsigned char *inq_result, 867 blist_flags_t *bflags, int async) 868 { 869 int ret; 870 871 /* 872 * XXX do not save the inquiry, since it can change underneath us, 873 * save just vendor/model/rev. 874 * 875 * Rather than save it and have an ioctl that retrieves the saved 876 * value, have an ioctl that executes the same INQUIRY code used 877 * in scsi_probe_lun, let user level programs doing INQUIRY 878 * scanning run at their own risk, or supply a user level program 879 * that can correctly scan. 880 */ 881 882 /* 883 * Copy at least 36 bytes of INQUIRY data, so that we don't 884 * dereference unallocated memory when accessing the Vendor, 885 * Product, and Revision strings. Badly behaved devices may set 886 * the INQUIRY Additional Length byte to a small value, indicating 887 * these strings are invalid, but often they contain plausible data 888 * nonetheless. It doesn't matter if the device sent < 36 bytes 889 * total, since scsi_probe_lun() initializes inq_result with 0s. 890 */ 891 sdev->inquiry = kmemdup(inq_result, 892 max_t(size_t, sdev->inquiry_len, 36), 893 GFP_KERNEL); 894 if (sdev->inquiry == NULL) 895 return SCSI_SCAN_NO_RESPONSE; 896 897 sdev->vendor = (char *) (sdev->inquiry + 8); 898 sdev->model = (char *) (sdev->inquiry + 16); 899 sdev->rev = (char *) (sdev->inquiry + 32); 900 901 if (strncmp(sdev->vendor, "ATA ", 8) == 0) { 902 /* 903 * sata emulation layer device. This is a hack to work around 904 * the SATL power management specifications which state that 905 * when the SATL detects the device has gone into standby 906 * mode, it shall respond with NOT READY. 907 */ 908 sdev->allow_restart = 1; 909 } 910 911 if (*bflags & BLIST_ISROM) { 912 sdev->type = TYPE_ROM; 913 sdev->removable = 1; 914 } else { 915 sdev->type = (inq_result[0] & 0x1f); 916 sdev->removable = (inq_result[1] & 0x80) >> 7; 917 918 /* 919 * some devices may respond with wrong type for 920 * well-known logical units. Force well-known type 921 * to enumerate them correctly. 922 */ 923 if (scsi_is_wlun(sdev->lun) && sdev->type != TYPE_WLUN) { 924 sdev_printk(KERN_WARNING, sdev, 925 "%s: correcting incorrect peripheral device type 0x%x for W-LUN 0x%16xhN\n", 926 __func__, sdev->type, (unsigned int)sdev->lun); 927 sdev->type = TYPE_WLUN; 928 } 929 930 } 931 932 if (sdev->type == TYPE_RBC || sdev->type == TYPE_ROM) { 933 /* RBC and MMC devices can return SCSI-3 compliance and yet 934 * still not support REPORT LUNS, so make them act as 935 * BLIST_NOREPORTLUN unless BLIST_REPORTLUN2 is 936 * specifically set */ 937 if ((*bflags & BLIST_REPORTLUN2) == 0) 938 *bflags |= BLIST_NOREPORTLUN; 939 } 940 941 /* 942 * For a peripheral qualifier (PQ) value of 1 (001b), the SCSI 943 * spec says: The device server is capable of supporting the 944 * specified peripheral device type on this logical unit. However, 945 * the physical device is not currently connected to this logical 946 * unit. 947 * 948 * The above is vague, as it implies that we could treat 001 and 949 * 011 the same. Stay compatible with previous code, and create a 950 * scsi_device for a PQ of 1 951 * 952 * Don't set the device offline here; rather let the upper 953 * level drivers eval the PQ to decide whether they should 954 * attach. So remove ((inq_result[0] >> 5) & 7) == 1 check. 955 */ 956 957 sdev->inq_periph_qual = (inq_result[0] >> 5) & 7; 958 sdev->lockable = sdev->removable; 959 sdev->soft_reset = (inq_result[7] & 1) && ((inq_result[3] & 7) == 2); 960 961 if (sdev->scsi_level >= SCSI_3 || 962 (sdev->inquiry_len > 56 && inq_result[56] & 0x04)) 963 sdev->ppr = 1; 964 if (inq_result[7] & 0x60) 965 sdev->wdtr = 1; 966 if (inq_result[7] & 0x10) 967 sdev->sdtr = 1; 968 969 sdev_printk(KERN_NOTICE, sdev, "%s %.8s %.16s %.4s PQ: %d " 970 "ANSI: %d%s\n", scsi_device_type(sdev->type), 971 sdev->vendor, sdev->model, sdev->rev, 972 sdev->inq_periph_qual, inq_result[2] & 0x07, 973 (inq_result[3] & 0x0f) == 1 ? " CCS" : ""); 974 975 if ((sdev->scsi_level >= SCSI_2) && (inq_result[7] & 2) && 976 !(*bflags & BLIST_NOTQ)) { 977 sdev->tagged_supported = 1; 978 sdev->simple_tags = 1; 979 } 980 981 /* 982 * Some devices (Texel CD ROM drives) have handshaking problems 983 * when used with the Seagate controllers. borken is initialized 984 * to 1, and then set it to 0 here. 985 */ 986 if ((*bflags & BLIST_BORKEN) == 0) 987 sdev->borken = 0; 988 989 if (*bflags & BLIST_NO_ULD_ATTACH) 990 sdev->no_uld_attach = 1; 991 992 /* 993 * Apparently some really broken devices (contrary to the SCSI 994 * standards) need to be selected without asserting ATN 995 */ 996 if (*bflags & BLIST_SELECT_NO_ATN) 997 sdev->select_no_atn = 1; 998 999 /* 1000 * Maximum 512 sector transfer length 1001 * broken RA4x00 Compaq Disk Array 1002 */ 1003 if (*bflags & BLIST_MAX_512) 1004 blk_queue_max_hw_sectors(sdev->request_queue, 512); 1005 /* 1006 * Max 1024 sector transfer length for targets that report incorrect 1007 * max/optimal lengths and relied on the old block layer safe default 1008 */ 1009 else if (*bflags & BLIST_MAX_1024) 1010 blk_queue_max_hw_sectors(sdev->request_queue, 1024); 1011 1012 /* 1013 * Some devices may not want to have a start command automatically 1014 * issued when a device is added. 1015 */ 1016 if (*bflags & BLIST_NOSTARTONADD) 1017 sdev->no_start_on_add = 1; 1018 1019 if (*bflags & BLIST_SINGLELUN) 1020 scsi_target(sdev)->single_lun = 1; 1021 1022 sdev->use_10_for_rw = 1; 1023 1024 /* some devices don't like REPORT SUPPORTED OPERATION CODES 1025 * and will simply timeout causing sd_mod init to take a very 1026 * very long time */ 1027 if (*bflags & BLIST_NO_RSOC) 1028 sdev->no_report_opcodes = 1; 1029 1030 /* set the device running here so that slave configure 1031 * may do I/O */ 1032 mutex_lock(&sdev->state_mutex); 1033 ret = scsi_device_set_state(sdev, SDEV_RUNNING); 1034 if (ret) 1035 ret = scsi_device_set_state(sdev, SDEV_BLOCK); 1036 mutex_unlock(&sdev->state_mutex); 1037 1038 if (ret) { 1039 sdev_printk(KERN_ERR, sdev, 1040 "in wrong state %s to complete scan\n", 1041 scsi_device_state_name(sdev->sdev_state)); 1042 return SCSI_SCAN_NO_RESPONSE; 1043 } 1044 1045 if (*bflags & BLIST_NOT_LOCKABLE) 1046 sdev->lockable = 0; 1047 1048 if (*bflags & BLIST_RETRY_HWERROR) 1049 sdev->retry_hwerror = 1; 1050 1051 if (*bflags & BLIST_NO_DIF) 1052 sdev->no_dif = 1; 1053 1054 if (*bflags & BLIST_UNMAP_LIMIT_WS) 1055 sdev->unmap_limit_for_ws = 1; 1056 1057 if (*bflags & BLIST_IGN_MEDIA_CHANGE) 1058 sdev->ignore_media_change = 1; 1059 1060 sdev->eh_timeout = SCSI_DEFAULT_EH_TIMEOUT; 1061 1062 if (*bflags & BLIST_TRY_VPD_PAGES) 1063 sdev->try_vpd_pages = 1; 1064 else if (*bflags & BLIST_SKIP_VPD_PAGES) 1065 sdev->skip_vpd_pages = 1; 1066 1067 transport_configure_device(&sdev->sdev_gendev); 1068 1069 if (sdev->host->hostt->slave_configure) { 1070 ret = sdev->host->hostt->slave_configure(sdev); 1071 if (ret) { 1072 /* 1073 * if LLDD reports slave not present, don't clutter 1074 * console with alloc failure messages 1075 */ 1076 if (ret != -ENXIO) { 1077 sdev_printk(KERN_ERR, sdev, 1078 "failed to configure device\n"); 1079 } 1080 return SCSI_SCAN_NO_RESPONSE; 1081 } 1082 1083 /* 1084 * The queue_depth is often changed in ->slave_configure. 1085 * Set up budget map again since memory consumption of 1086 * the map depends on actual queue depth. 1087 */ 1088 scsi_realloc_sdev_budget_map(sdev, sdev->queue_depth); 1089 } 1090 1091 if (sdev->scsi_level >= SCSI_3) 1092 scsi_attach_vpd(sdev); 1093 1094 sdev->max_queue_depth = sdev->queue_depth; 1095 WARN_ON_ONCE(sdev->max_queue_depth > sdev->budget_map.depth); 1096 sdev->sdev_bflags = *bflags; 1097 1098 /* 1099 * Ok, the device is now all set up, we can 1100 * register it and tell the rest of the kernel 1101 * about it. 1102 */ 1103 if (!async && scsi_sysfs_add_sdev(sdev) != 0) 1104 return SCSI_SCAN_NO_RESPONSE; 1105 1106 return SCSI_SCAN_LUN_PRESENT; 1107 } 1108 1109 #ifdef CONFIG_SCSI_LOGGING 1110 /** 1111 * scsi_inq_str - print INQUIRY data from min to max index, strip trailing whitespace 1112 * @buf: Output buffer with at least end-first+1 bytes of space 1113 * @inq: Inquiry buffer (input) 1114 * @first: Offset of string into inq 1115 * @end: Index after last character in inq 1116 */ 1117 static unsigned char *scsi_inq_str(unsigned char *buf, unsigned char *inq, 1118 unsigned first, unsigned end) 1119 { 1120 unsigned term = 0, idx; 1121 1122 for (idx = 0; idx + first < end && idx + first < inq[4] + 5; idx++) { 1123 if (inq[idx+first] > ' ') { 1124 buf[idx] = inq[idx+first]; 1125 term = idx+1; 1126 } else { 1127 buf[idx] = ' '; 1128 } 1129 } 1130 buf[term] = 0; 1131 return buf; 1132 } 1133 #endif 1134 1135 /** 1136 * scsi_probe_and_add_lun - probe a LUN, if a LUN is found add it 1137 * @starget: pointer to target device structure 1138 * @lun: LUN of target device 1139 * @bflagsp: store bflags here if not NULL 1140 * @sdevp: probe the LUN corresponding to this scsi_device 1141 * @rescan: if not equal to SCSI_SCAN_INITIAL skip some code only 1142 * needed on first scan 1143 * @hostdata: passed to scsi_alloc_sdev() 1144 * 1145 * Description: 1146 * Call scsi_probe_lun, if a LUN with an attached device is found, 1147 * allocate and set it up by calling scsi_add_lun. 1148 * 1149 * Return: 1150 * 1151 * - SCSI_SCAN_NO_RESPONSE: could not allocate or setup a scsi_device 1152 * - SCSI_SCAN_TARGET_PRESENT: target responded, but no device is 1153 * attached at the LUN 1154 * - SCSI_SCAN_LUN_PRESENT: a new scsi_device was allocated and initialized 1155 **/ 1156 static int scsi_probe_and_add_lun(struct scsi_target *starget, 1157 u64 lun, blist_flags_t *bflagsp, 1158 struct scsi_device **sdevp, 1159 enum scsi_scan_mode rescan, 1160 void *hostdata) 1161 { 1162 struct scsi_device *sdev; 1163 unsigned char *result; 1164 blist_flags_t bflags; 1165 int res = SCSI_SCAN_NO_RESPONSE, result_len = 256; 1166 struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); 1167 1168 /* 1169 * The rescan flag is used as an optimization, the first scan of a 1170 * host adapter calls into here with rescan == 0. 1171 */ 1172 sdev = scsi_device_lookup_by_target(starget, lun); 1173 if (sdev) { 1174 if (rescan != SCSI_SCAN_INITIAL || !scsi_device_created(sdev)) { 1175 SCSI_LOG_SCAN_BUS(3, sdev_printk(KERN_INFO, sdev, 1176 "scsi scan: device exists on %s\n", 1177 dev_name(&sdev->sdev_gendev))); 1178 if (sdevp) 1179 *sdevp = sdev; 1180 else 1181 scsi_device_put(sdev); 1182 1183 if (bflagsp) 1184 *bflagsp = scsi_get_device_flags(sdev, 1185 sdev->vendor, 1186 sdev->model); 1187 return SCSI_SCAN_LUN_PRESENT; 1188 } 1189 scsi_device_put(sdev); 1190 } else 1191 sdev = scsi_alloc_sdev(starget, lun, hostdata); 1192 if (!sdev) 1193 goto out; 1194 1195 result = kmalloc(result_len, GFP_KERNEL); 1196 if (!result) 1197 goto out_free_sdev; 1198 1199 if (scsi_probe_lun(sdev, result, result_len, &bflags)) 1200 goto out_free_result; 1201 1202 if (bflagsp) 1203 *bflagsp = bflags; 1204 /* 1205 * result contains valid SCSI INQUIRY data. 1206 */ 1207 if ((result[0] >> 5) == 3) { 1208 /* 1209 * For a Peripheral qualifier 3 (011b), the SCSI 1210 * spec says: The device server is not capable of 1211 * supporting a physical device on this logical 1212 * unit. 1213 * 1214 * For disks, this implies that there is no 1215 * logical disk configured at sdev->lun, but there 1216 * is a target id responding. 1217 */ 1218 SCSI_LOG_SCAN_BUS(2, sdev_printk(KERN_INFO, sdev, "scsi scan:" 1219 " peripheral qualifier of 3, device not" 1220 " added\n")) 1221 if (lun == 0) { 1222 SCSI_LOG_SCAN_BUS(1, { 1223 unsigned char vend[9]; 1224 unsigned char mod[17]; 1225 1226 sdev_printk(KERN_INFO, sdev, 1227 "scsi scan: consider passing scsi_mod." 1228 "dev_flags=%s:%s:0x240 or 0x1000240\n", 1229 scsi_inq_str(vend, result, 8, 16), 1230 scsi_inq_str(mod, result, 16, 32)); 1231 }); 1232 1233 } 1234 1235 res = SCSI_SCAN_TARGET_PRESENT; 1236 goto out_free_result; 1237 } 1238 1239 /* 1240 * Some targets may set slight variations of PQ and PDT to signal 1241 * that no LUN is present, so don't add sdev in these cases. 1242 * Two specific examples are: 1243 * 1) NetApp targets: return PQ=1, PDT=0x1f 1244 * 2) IBM/2145 targets: return PQ=1, PDT=0 1245 * 3) USB UFI: returns PDT=0x1f, with the PQ bits being "reserved" 1246 * in the UFI 1.0 spec (we cannot rely on reserved bits). 1247 * 1248 * References: 1249 * 1) SCSI SPC-3, pp. 145-146 1250 * PQ=1: "A peripheral device having the specified peripheral 1251 * device type is not connected to this logical unit. However, the 1252 * device server is capable of supporting the specified peripheral 1253 * device type on this logical unit." 1254 * PDT=0x1f: "Unknown or no device type" 1255 * 2) USB UFI 1.0, p. 20 1256 * PDT=00h Direct-access device (floppy) 1257 * PDT=1Fh none (no FDD connected to the requested logical unit) 1258 */ 1259 if (((result[0] >> 5) == 1 || 1260 (starget->pdt_1f_for_no_lun && (result[0] & 0x1f) == 0x1f)) && 1261 !scsi_is_wlun(lun)) { 1262 SCSI_LOG_SCAN_BUS(3, sdev_printk(KERN_INFO, sdev, 1263 "scsi scan: peripheral device type" 1264 " of 31, no device added\n")); 1265 res = SCSI_SCAN_TARGET_PRESENT; 1266 goto out_free_result; 1267 } 1268 1269 res = scsi_add_lun(sdev, result, &bflags, shost->async_scan); 1270 if (res == SCSI_SCAN_LUN_PRESENT) { 1271 if (bflags & BLIST_KEY) { 1272 sdev->lockable = 0; 1273 scsi_unlock_floptical(sdev, result); 1274 } 1275 } 1276 1277 out_free_result: 1278 kfree(result); 1279 out_free_sdev: 1280 if (res == SCSI_SCAN_LUN_PRESENT) { 1281 if (sdevp) { 1282 if (scsi_device_get(sdev) == 0) { 1283 *sdevp = sdev; 1284 } else { 1285 __scsi_remove_device(sdev); 1286 res = SCSI_SCAN_NO_RESPONSE; 1287 } 1288 } 1289 } else 1290 __scsi_remove_device(sdev); 1291 out: 1292 return res; 1293 } 1294 1295 /** 1296 * scsi_sequential_lun_scan - sequentially scan a SCSI target 1297 * @starget: pointer to target structure to scan 1298 * @bflags: black/white list flag for LUN 0 1299 * @scsi_level: Which version of the standard does this device adhere to 1300 * @rescan: passed to scsi_probe_add_lun() 1301 * 1302 * Description: 1303 * Generally, scan from LUN 1 (LUN 0 is assumed to already have been 1304 * scanned) to some maximum lun until a LUN is found with no device 1305 * attached. Use the bflags to figure out any oddities. 1306 * 1307 * Modifies sdevscan->lun. 1308 **/ 1309 static void scsi_sequential_lun_scan(struct scsi_target *starget, 1310 blist_flags_t bflags, int scsi_level, 1311 enum scsi_scan_mode rescan) 1312 { 1313 uint max_dev_lun; 1314 u64 sparse_lun, lun; 1315 struct Scsi_Host *shost = dev_to_shost(starget->dev.parent); 1316 1317 SCSI_LOG_SCAN_BUS(3, starget_printk(KERN_INFO, starget, 1318 "scsi scan: Sequential scan\n")); 1319 1320 max_dev_lun = min(max_scsi_luns, shost->max_lun); 1321 /* 1322 * If this device is known to support sparse multiple units, 1323 * override the other settings, and scan all of them. Normally, 1324 * SCSI-3 devices should be scanned via the REPORT LUNS. 1325 */ 1326 if (bflags & BLIST_SPARSELUN) { 1327 max_dev_lun = shost->max_lun; 1328 sparse_lun = 1; 1329 } else 1330 sparse_lun = 0; 1331 1332 /* 1333 * If less than SCSI_1_CCS, and no special lun scanning, stop 1334 * scanning; this matches 2.4 behaviour, but could just be a bug 1335 * (to continue scanning a SCSI_1_CCS device). 1336 * 1337 * This test is broken. We might not have any device on lun0 for 1338 * a sparselun device, and if that's the case then how would we 1339 * know the real scsi_level, eh? It might make sense to just not 1340 * scan any SCSI_1 device for non-0 luns, but that check would best 1341 * go into scsi_alloc_sdev() and just have it return null when asked 1342 * to alloc an sdev for lun > 0 on an already found SCSI_1 device. 1343 * 1344 if ((sdevscan->scsi_level < SCSI_1_CCS) && 1345 ((bflags & (BLIST_FORCELUN | BLIST_SPARSELUN | BLIST_MAX5LUN)) 1346 == 0)) 1347 return; 1348 */ 1349 /* 1350 * If this device is known to support multiple units, override 1351 * the other settings, and scan all of them. 1352 */ 1353 if (bflags & BLIST_FORCELUN) 1354 max_dev_lun = shost->max_lun; 1355 /* 1356 * REGAL CDC-4X: avoid hang after LUN 4 1357 */ 1358 if (bflags & BLIST_MAX5LUN) 1359 max_dev_lun = min(5U, max_dev_lun); 1360 /* 1361 * Do not scan SCSI-2 or lower device past LUN 7, unless 1362 * BLIST_LARGELUN. 1363 */ 1364 if (scsi_level < SCSI_3 && !(bflags & BLIST_LARGELUN)) 1365 max_dev_lun = min(8U, max_dev_lun); 1366 else 1367 max_dev_lun = min(256U, max_dev_lun); 1368 1369 /* 1370 * We have already scanned LUN 0, so start at LUN 1. Keep scanning 1371 * until we reach the max, or no LUN is found and we are not 1372 * sparse_lun. 1373 */ 1374 for (lun = 1; lun < max_dev_lun; ++lun) 1375 if ((scsi_probe_and_add_lun(starget, lun, NULL, NULL, rescan, 1376 NULL) != SCSI_SCAN_LUN_PRESENT) && 1377 !sparse_lun) 1378 return; 1379 } 1380 1381 /** 1382 * scsi_report_lun_scan - Scan using SCSI REPORT LUN results 1383 * @starget: which target 1384 * @bflags: Zero or a mix of BLIST_NOLUN, BLIST_REPORTLUN2, or BLIST_NOREPORTLUN 1385 * @rescan: nonzero if we can skip code only needed on first scan 1386 * 1387 * Description: 1388 * Fast scanning for modern (SCSI-3) devices by sending a REPORT LUN command. 1389 * Scan the resulting list of LUNs by calling scsi_probe_and_add_lun. 1390 * 1391 * If BLINK_REPORTLUN2 is set, scan a target that supports more than 8 1392 * LUNs even if it's older than SCSI-3. 1393 * If BLIST_NOREPORTLUN is set, return 1 always. 1394 * If BLIST_NOLUN is set, return 0 always. 1395 * If starget->no_report_luns is set, return 1 always. 1396 * 1397 * Return: 1398 * 0: scan completed (or no memory, so further scanning is futile) 1399 * 1: could not scan with REPORT LUN 1400 **/ 1401 static int scsi_report_lun_scan(struct scsi_target *starget, blist_flags_t bflags, 1402 enum scsi_scan_mode rescan) 1403 { 1404 unsigned char scsi_cmd[MAX_COMMAND_SIZE]; 1405 unsigned int length; 1406 u64 lun; 1407 unsigned int num_luns; 1408 unsigned int retries; 1409 int result; 1410 struct scsi_lun *lunp, *lun_data; 1411 struct scsi_sense_hdr sshdr; 1412 struct scsi_device *sdev; 1413 struct Scsi_Host *shost = dev_to_shost(&starget->dev); 1414 int ret = 0; 1415 1416 /* 1417 * Only support SCSI-3 and up devices if BLIST_NOREPORTLUN is not set. 1418 * Also allow SCSI-2 if BLIST_REPORTLUN2 is set and host adapter does 1419 * support more than 8 LUNs. 1420 * Don't attempt if the target doesn't support REPORT LUNS. 1421 */ 1422 if (bflags & BLIST_NOREPORTLUN) 1423 return 1; 1424 if (starget->scsi_level < SCSI_2 && 1425 starget->scsi_level != SCSI_UNKNOWN) 1426 return 1; 1427 if (starget->scsi_level < SCSI_3 && 1428 (!(bflags & BLIST_REPORTLUN2) || shost->max_lun <= 8)) 1429 return 1; 1430 if (bflags & BLIST_NOLUN) 1431 return 0; 1432 if (starget->no_report_luns) 1433 return 1; 1434 1435 if (!(sdev = scsi_device_lookup_by_target(starget, 0))) { 1436 sdev = scsi_alloc_sdev(starget, 0, NULL); 1437 if (!sdev) 1438 return 0; 1439 if (scsi_device_get(sdev)) { 1440 __scsi_remove_device(sdev); 1441 return 0; 1442 } 1443 } 1444 1445 /* 1446 * Allocate enough to hold the header (the same size as one scsi_lun) 1447 * plus the number of luns we are requesting. 511 was the default 1448 * value of the now removed max_report_luns parameter. 1449 */ 1450 length = (511 + 1) * sizeof(struct scsi_lun); 1451 retry: 1452 lun_data = kmalloc(length, GFP_KERNEL); 1453 if (!lun_data) { 1454 printk(ALLOC_FAILURE_MSG, __func__); 1455 goto out; 1456 } 1457 1458 scsi_cmd[0] = REPORT_LUNS; 1459 1460 /* 1461 * bytes 1 - 5: reserved, set to zero. 1462 */ 1463 memset(&scsi_cmd[1], 0, 5); 1464 1465 /* 1466 * bytes 6 - 9: length of the command. 1467 */ 1468 put_unaligned_be32(length, &scsi_cmd[6]); 1469 1470 scsi_cmd[10] = 0; /* reserved */ 1471 scsi_cmd[11] = 0; /* control */ 1472 1473 /* 1474 * We can get a UNIT ATTENTION, for example a power on/reset, so 1475 * retry a few times (like sd.c does for TEST UNIT READY). 1476 * Experience shows some combinations of adapter/devices get at 1477 * least two power on/resets. 1478 * 1479 * Illegal requests (for devices that do not support REPORT LUNS) 1480 * should come through as a check condition, and will not generate 1481 * a retry. 1482 */ 1483 for (retries = 0; retries < 3; retries++) { 1484 SCSI_LOG_SCAN_BUS(3, sdev_printk (KERN_INFO, sdev, 1485 "scsi scan: Sending REPORT LUNS to (try %d)\n", 1486 retries)); 1487 1488 result = scsi_execute_req(sdev, scsi_cmd, DMA_FROM_DEVICE, 1489 lun_data, length, &sshdr, 1490 SCSI_REPORT_LUNS_TIMEOUT, 3, NULL); 1491 1492 SCSI_LOG_SCAN_BUS(3, sdev_printk (KERN_INFO, sdev, 1493 "scsi scan: REPORT LUNS" 1494 " %s (try %d) result 0x%x\n", 1495 result ? "failed" : "successful", 1496 retries, result)); 1497 if (result == 0) 1498 break; 1499 else if (scsi_sense_valid(&sshdr)) { 1500 if (sshdr.sense_key != UNIT_ATTENTION) 1501 break; 1502 } 1503 } 1504 1505 if (result) { 1506 /* 1507 * The device probably does not support a REPORT LUN command 1508 */ 1509 ret = 1; 1510 goto out_err; 1511 } 1512 1513 /* 1514 * Get the length from the first four bytes of lun_data. 1515 */ 1516 if (get_unaligned_be32(lun_data->scsi_lun) + 1517 sizeof(struct scsi_lun) > length) { 1518 length = get_unaligned_be32(lun_data->scsi_lun) + 1519 sizeof(struct scsi_lun); 1520 kfree(lun_data); 1521 goto retry; 1522 } 1523 length = get_unaligned_be32(lun_data->scsi_lun); 1524 1525 num_luns = (length / sizeof(struct scsi_lun)); 1526 1527 SCSI_LOG_SCAN_BUS(3, sdev_printk (KERN_INFO, sdev, 1528 "scsi scan: REPORT LUN scan\n")); 1529 1530 /* 1531 * Scan the luns in lun_data. The entry at offset 0 is really 1532 * the header, so start at 1 and go up to and including num_luns. 1533 */ 1534 for (lunp = &lun_data[1]; lunp <= &lun_data[num_luns]; lunp++) { 1535 lun = scsilun_to_int(lunp); 1536 1537 if (lun > sdev->host->max_lun) { 1538 sdev_printk(KERN_WARNING, sdev, 1539 "lun%llu has a LUN larger than" 1540 " allowed by the host adapter\n", lun); 1541 } else { 1542 int res; 1543 1544 res = scsi_probe_and_add_lun(starget, 1545 lun, NULL, NULL, rescan, NULL); 1546 if (res == SCSI_SCAN_NO_RESPONSE) { 1547 /* 1548 * Got some results, but now none, abort. 1549 */ 1550 sdev_printk(KERN_ERR, sdev, 1551 "Unexpected response" 1552 " from lun %llu while scanning, scan" 1553 " aborted\n", (unsigned long long)lun); 1554 break; 1555 } 1556 } 1557 } 1558 1559 out_err: 1560 kfree(lun_data); 1561 out: 1562 if (scsi_device_created(sdev)) 1563 /* 1564 * the sdev we used didn't appear in the report luns scan 1565 */ 1566 __scsi_remove_device(sdev); 1567 scsi_device_put(sdev); 1568 return ret; 1569 } 1570 1571 struct scsi_device *__scsi_add_device(struct Scsi_Host *shost, uint channel, 1572 uint id, u64 lun, void *hostdata) 1573 { 1574 struct scsi_device *sdev = ERR_PTR(-ENODEV); 1575 struct device *parent = &shost->shost_gendev; 1576 struct scsi_target *starget; 1577 1578 if (strncmp(scsi_scan_type, "none", 4) == 0) 1579 return ERR_PTR(-ENODEV); 1580 1581 starget = scsi_alloc_target(parent, channel, id); 1582 if (!starget) 1583 return ERR_PTR(-ENOMEM); 1584 scsi_autopm_get_target(starget); 1585 1586 mutex_lock(&shost->scan_mutex); 1587 if (!shost->async_scan) 1588 scsi_complete_async_scans(); 1589 1590 if (scsi_host_scan_allowed(shost) && scsi_autopm_get_host(shost) == 0) { 1591 scsi_probe_and_add_lun(starget, lun, NULL, &sdev, 1, hostdata); 1592 scsi_autopm_put_host(shost); 1593 } 1594 mutex_unlock(&shost->scan_mutex); 1595 scsi_autopm_put_target(starget); 1596 /* 1597 * paired with scsi_alloc_target(). Target will be destroyed unless 1598 * scsi_probe_and_add_lun made an underlying device visible 1599 */ 1600 scsi_target_reap(starget); 1601 put_device(&starget->dev); 1602 1603 return sdev; 1604 } 1605 EXPORT_SYMBOL(__scsi_add_device); 1606 1607 int scsi_add_device(struct Scsi_Host *host, uint channel, 1608 uint target, u64 lun) 1609 { 1610 struct scsi_device *sdev = 1611 __scsi_add_device(host, channel, target, lun, NULL); 1612 if (IS_ERR(sdev)) 1613 return PTR_ERR(sdev); 1614 1615 scsi_device_put(sdev); 1616 return 0; 1617 } 1618 EXPORT_SYMBOL(scsi_add_device); 1619 1620 void scsi_rescan_device(struct device *dev) 1621 { 1622 struct scsi_device *sdev = to_scsi_device(dev); 1623 1624 device_lock(dev); 1625 1626 scsi_attach_vpd(sdev); 1627 1628 if (sdev->handler && sdev->handler->rescan) 1629 sdev->handler->rescan(sdev); 1630 1631 if (dev->driver && try_module_get(dev->driver->owner)) { 1632 struct scsi_driver *drv = to_scsi_driver(dev->driver); 1633 1634 if (drv->rescan) 1635 drv->rescan(dev); 1636 module_put(dev->driver->owner); 1637 } 1638 device_unlock(dev); 1639 } 1640 EXPORT_SYMBOL(scsi_rescan_device); 1641 1642 static void __scsi_scan_target(struct device *parent, unsigned int channel, 1643 unsigned int id, u64 lun, enum scsi_scan_mode rescan) 1644 { 1645 struct Scsi_Host *shost = dev_to_shost(parent); 1646 blist_flags_t bflags = 0; 1647 int res; 1648 struct scsi_target *starget; 1649 1650 if (shost->this_id == id) 1651 /* 1652 * Don't scan the host adapter 1653 */ 1654 return; 1655 1656 starget = scsi_alloc_target(parent, channel, id); 1657 if (!starget) 1658 return; 1659 scsi_autopm_get_target(starget); 1660 1661 if (lun != SCAN_WILD_CARD) { 1662 /* 1663 * Scan for a specific host/chan/id/lun. 1664 */ 1665 scsi_probe_and_add_lun(starget, lun, NULL, NULL, rescan, NULL); 1666 goto out_reap; 1667 } 1668 1669 /* 1670 * Scan LUN 0, if there is some response, scan further. Ideally, we 1671 * would not configure LUN 0 until all LUNs are scanned. 1672 */ 1673 res = scsi_probe_and_add_lun(starget, 0, &bflags, NULL, rescan, NULL); 1674 if (res == SCSI_SCAN_LUN_PRESENT || res == SCSI_SCAN_TARGET_PRESENT) { 1675 if (scsi_report_lun_scan(starget, bflags, rescan) != 0) 1676 /* 1677 * The REPORT LUN did not scan the target, 1678 * do a sequential scan. 1679 */ 1680 scsi_sequential_lun_scan(starget, bflags, 1681 starget->scsi_level, rescan); 1682 } 1683 1684 out_reap: 1685 scsi_autopm_put_target(starget); 1686 /* 1687 * paired with scsi_alloc_target(): determine if the target has 1688 * any children at all and if not, nuke it 1689 */ 1690 scsi_target_reap(starget); 1691 1692 put_device(&starget->dev); 1693 } 1694 1695 /** 1696 * scsi_scan_target - scan a target id, possibly including all LUNs on the target. 1697 * @parent: host to scan 1698 * @channel: channel to scan 1699 * @id: target id to scan 1700 * @lun: Specific LUN to scan or SCAN_WILD_CARD 1701 * @rescan: passed to LUN scanning routines; SCSI_SCAN_INITIAL for 1702 * no rescan, SCSI_SCAN_RESCAN to rescan existing LUNs, 1703 * and SCSI_SCAN_MANUAL to force scanning even if 1704 * 'scan=manual' is set. 1705 * 1706 * Description: 1707 * Scan the target id on @parent, @channel, and @id. Scan at least LUN 0, 1708 * and possibly all LUNs on the target id. 1709 * 1710 * First try a REPORT LUN scan, if that does not scan the target, do a 1711 * sequential scan of LUNs on the target id. 1712 **/ 1713 void scsi_scan_target(struct device *parent, unsigned int channel, 1714 unsigned int id, u64 lun, enum scsi_scan_mode rescan) 1715 { 1716 struct Scsi_Host *shost = dev_to_shost(parent); 1717 1718 if (strncmp(scsi_scan_type, "none", 4) == 0) 1719 return; 1720 1721 if (rescan != SCSI_SCAN_MANUAL && 1722 strncmp(scsi_scan_type, "manual", 6) == 0) 1723 return; 1724 1725 mutex_lock(&shost->scan_mutex); 1726 if (!shost->async_scan) 1727 scsi_complete_async_scans(); 1728 1729 if (scsi_host_scan_allowed(shost) && scsi_autopm_get_host(shost) == 0) { 1730 __scsi_scan_target(parent, channel, id, lun, rescan); 1731 scsi_autopm_put_host(shost); 1732 } 1733 mutex_unlock(&shost->scan_mutex); 1734 } 1735 EXPORT_SYMBOL(scsi_scan_target); 1736 1737 static void scsi_scan_channel(struct Scsi_Host *shost, unsigned int channel, 1738 unsigned int id, u64 lun, 1739 enum scsi_scan_mode rescan) 1740 { 1741 uint order_id; 1742 1743 if (id == SCAN_WILD_CARD) 1744 for (id = 0; id < shost->max_id; ++id) { 1745 /* 1746 * XXX adapter drivers when possible (FCP, iSCSI) 1747 * could modify max_id to match the current max, 1748 * not the absolute max. 1749 * 1750 * XXX add a shost id iterator, so for example, 1751 * the FC ID can be the same as a target id 1752 * without a huge overhead of sparse id's. 1753 */ 1754 if (shost->reverse_ordering) 1755 /* 1756 * Scan from high to low id. 1757 */ 1758 order_id = shost->max_id - id - 1; 1759 else 1760 order_id = id; 1761 __scsi_scan_target(&shost->shost_gendev, channel, 1762 order_id, lun, rescan); 1763 } 1764 else 1765 __scsi_scan_target(&shost->shost_gendev, channel, 1766 id, lun, rescan); 1767 } 1768 1769 int scsi_scan_host_selected(struct Scsi_Host *shost, unsigned int channel, 1770 unsigned int id, u64 lun, 1771 enum scsi_scan_mode rescan) 1772 { 1773 SCSI_LOG_SCAN_BUS(3, shost_printk (KERN_INFO, shost, 1774 "%s: <%u:%u:%llu>\n", 1775 __func__, channel, id, lun)); 1776 1777 if (((channel != SCAN_WILD_CARD) && (channel > shost->max_channel)) || 1778 ((id != SCAN_WILD_CARD) && (id >= shost->max_id)) || 1779 ((lun != SCAN_WILD_CARD) && (lun >= shost->max_lun))) 1780 return -EINVAL; 1781 1782 mutex_lock(&shost->scan_mutex); 1783 if (!shost->async_scan) 1784 scsi_complete_async_scans(); 1785 1786 if (scsi_host_scan_allowed(shost) && scsi_autopm_get_host(shost) == 0) { 1787 if (channel == SCAN_WILD_CARD) 1788 for (channel = 0; channel <= shost->max_channel; 1789 channel++) 1790 scsi_scan_channel(shost, channel, id, lun, 1791 rescan); 1792 else 1793 scsi_scan_channel(shost, channel, id, lun, rescan); 1794 scsi_autopm_put_host(shost); 1795 } 1796 mutex_unlock(&shost->scan_mutex); 1797 1798 return 0; 1799 } 1800 1801 static void scsi_sysfs_add_devices(struct Scsi_Host *shost) 1802 { 1803 struct scsi_device *sdev; 1804 shost_for_each_device(sdev, shost) { 1805 /* target removed before the device could be added */ 1806 if (sdev->sdev_state == SDEV_DEL) 1807 continue; 1808 /* If device is already visible, skip adding it to sysfs */ 1809 if (sdev->is_visible) 1810 continue; 1811 if (!scsi_host_scan_allowed(shost) || 1812 scsi_sysfs_add_sdev(sdev) != 0) 1813 __scsi_remove_device(sdev); 1814 } 1815 } 1816 1817 /** 1818 * scsi_prep_async_scan - prepare for an async scan 1819 * @shost: the host which will be scanned 1820 * Returns: a cookie to be passed to scsi_finish_async_scan() 1821 * 1822 * Tells the midlayer this host is going to do an asynchronous scan. 1823 * It reserves the host's position in the scanning list and ensures 1824 * that other asynchronous scans started after this one won't affect the 1825 * ordering of the discovered devices. 1826 */ 1827 static struct async_scan_data *scsi_prep_async_scan(struct Scsi_Host *shost) 1828 { 1829 struct async_scan_data *data = NULL; 1830 unsigned long flags; 1831 1832 if (strncmp(scsi_scan_type, "sync", 4) == 0) 1833 return NULL; 1834 1835 mutex_lock(&shost->scan_mutex); 1836 if (shost->async_scan) { 1837 shost_printk(KERN_DEBUG, shost, "%s called twice\n", __func__); 1838 goto err; 1839 } 1840 1841 data = kmalloc(sizeof(*data), GFP_KERNEL); 1842 if (!data) 1843 goto err; 1844 data->shost = scsi_host_get(shost); 1845 if (!data->shost) 1846 goto err; 1847 init_completion(&data->prev_finished); 1848 1849 spin_lock_irqsave(shost->host_lock, flags); 1850 shost->async_scan = 1; 1851 spin_unlock_irqrestore(shost->host_lock, flags); 1852 mutex_unlock(&shost->scan_mutex); 1853 1854 spin_lock(&async_scan_lock); 1855 if (list_empty(&scanning_hosts)) 1856 complete(&data->prev_finished); 1857 list_add_tail(&data->list, &scanning_hosts); 1858 spin_unlock(&async_scan_lock); 1859 1860 return data; 1861 1862 err: 1863 mutex_unlock(&shost->scan_mutex); 1864 kfree(data); 1865 return NULL; 1866 } 1867 1868 /** 1869 * scsi_finish_async_scan - asynchronous scan has finished 1870 * @data: cookie returned from earlier call to scsi_prep_async_scan() 1871 * 1872 * All the devices currently attached to this host have been found. 1873 * This function announces all the devices it has found to the rest 1874 * of the system. 1875 */ 1876 static void scsi_finish_async_scan(struct async_scan_data *data) 1877 { 1878 struct Scsi_Host *shost; 1879 unsigned long flags; 1880 1881 if (!data) 1882 return; 1883 1884 shost = data->shost; 1885 1886 mutex_lock(&shost->scan_mutex); 1887 1888 if (!shost->async_scan) { 1889 shost_printk(KERN_INFO, shost, "%s called twice\n", __func__); 1890 dump_stack(); 1891 mutex_unlock(&shost->scan_mutex); 1892 return; 1893 } 1894 1895 wait_for_completion(&data->prev_finished); 1896 1897 scsi_sysfs_add_devices(shost); 1898 1899 spin_lock_irqsave(shost->host_lock, flags); 1900 shost->async_scan = 0; 1901 spin_unlock_irqrestore(shost->host_lock, flags); 1902 1903 mutex_unlock(&shost->scan_mutex); 1904 1905 spin_lock(&async_scan_lock); 1906 list_del(&data->list); 1907 if (!list_empty(&scanning_hosts)) { 1908 struct async_scan_data *next = list_entry(scanning_hosts.next, 1909 struct async_scan_data, list); 1910 complete(&next->prev_finished); 1911 } 1912 spin_unlock(&async_scan_lock); 1913 1914 scsi_autopm_put_host(shost); 1915 scsi_host_put(shost); 1916 kfree(data); 1917 } 1918 1919 static void do_scsi_scan_host(struct Scsi_Host *shost) 1920 { 1921 if (shost->hostt->scan_finished) { 1922 unsigned long start = jiffies; 1923 if (shost->hostt->scan_start) 1924 shost->hostt->scan_start(shost); 1925 1926 while (!shost->hostt->scan_finished(shost, jiffies - start)) 1927 msleep(10); 1928 } else { 1929 scsi_scan_host_selected(shost, SCAN_WILD_CARD, SCAN_WILD_CARD, 1930 SCAN_WILD_CARD, 0); 1931 } 1932 } 1933 1934 static void do_scan_async(void *_data, async_cookie_t c) 1935 { 1936 struct async_scan_data *data = _data; 1937 struct Scsi_Host *shost = data->shost; 1938 1939 do_scsi_scan_host(shost); 1940 scsi_finish_async_scan(data); 1941 } 1942 1943 /** 1944 * scsi_scan_host - scan the given adapter 1945 * @shost: adapter to scan 1946 **/ 1947 void scsi_scan_host(struct Scsi_Host *shost) 1948 { 1949 struct async_scan_data *data; 1950 1951 if (strncmp(scsi_scan_type, "none", 4) == 0 || 1952 strncmp(scsi_scan_type, "manual", 6) == 0) 1953 return; 1954 if (scsi_autopm_get_host(shost) < 0) 1955 return; 1956 1957 data = scsi_prep_async_scan(shost); 1958 if (!data) { 1959 do_scsi_scan_host(shost); 1960 scsi_autopm_put_host(shost); 1961 return; 1962 } 1963 1964 /* register with the async subsystem so wait_for_device_probe() 1965 * will flush this work 1966 */ 1967 async_schedule(do_scan_async, data); 1968 1969 /* scsi_autopm_put_host(shost) is called in scsi_finish_async_scan() */ 1970 } 1971 EXPORT_SYMBOL(scsi_scan_host); 1972 1973 void scsi_forget_host(struct Scsi_Host *shost) 1974 { 1975 struct scsi_device *sdev; 1976 unsigned long flags; 1977 1978 restart: 1979 spin_lock_irqsave(shost->host_lock, flags); 1980 list_for_each_entry(sdev, &shost->__devices, siblings) { 1981 if (sdev->sdev_state == SDEV_DEL) 1982 continue; 1983 spin_unlock_irqrestore(shost->host_lock, flags); 1984 __scsi_remove_device(sdev); 1985 goto restart; 1986 } 1987 spin_unlock_irqrestore(shost->host_lock, flags); 1988 } 1989 1990