1 /* 2 * QLogic Fibre Channel HBA Driver 3 * Copyright (c) 2003-2014 QLogic Corporation 4 * 5 * See LICENSE.qla2xxx for copyright and licensing details. 6 */ 7 #ifndef __QLA_FW_H 8 #define __QLA_FW_H 9 10 #include <linux/nvme.h> 11 #include <linux/nvme-fc.h> 12 13 #define MBS_CHECKSUM_ERROR 0x4010 14 #define MBS_INVALID_PRODUCT_KEY 0x4020 15 16 /* 17 * Firmware Options. 18 */ 19 #define FO1_ENABLE_PUREX BIT_10 20 #define FO1_DISABLE_LED_CTRL BIT_6 21 #define FO1_ENABLE_8016 BIT_0 22 #define FO2_ENABLE_SEL_CLASS2 BIT_5 23 #define FO3_NO_ABTS_ON_LINKDOWN BIT_14 24 #define FO3_HOLD_STS_IOCB BIT_12 25 26 /* 27 * Port Database structure definition for ISP 24xx. 28 */ 29 #define PDO_FORCE_ADISC BIT_1 30 #define PDO_FORCE_PLOGI BIT_0 31 32 33 #define PORT_DATABASE_24XX_SIZE 64 34 struct port_database_24xx { 35 uint16_t flags; 36 #define PDF_TASK_RETRY_ID BIT_14 37 #define PDF_FC_TAPE BIT_7 38 #define PDF_ACK0_CAPABLE BIT_6 39 #define PDF_FCP2_CONF BIT_5 40 #define PDF_CLASS_2 BIT_4 41 #define PDF_HARD_ADDR BIT_1 42 43 /* 44 * for NVMe, the login_state field has been 45 * split into nibbles. 46 * The lower nibble is for FCP. 47 * The upper nibble is for NVMe. 48 */ 49 uint8_t current_login_state; 50 uint8_t last_login_state; 51 #define PDS_PLOGI_PENDING 0x03 52 #define PDS_PLOGI_COMPLETE 0x04 53 #define PDS_PRLI_PENDING 0x05 54 #define PDS_PRLI_COMPLETE 0x06 55 #define PDS_PORT_UNAVAILABLE 0x07 56 #define PDS_PRLO_PENDING 0x09 57 #define PDS_LOGO_PENDING 0x11 58 #define PDS_PRLI2_PENDING 0x12 59 60 uint8_t hard_address[3]; 61 uint8_t reserved_1; 62 63 uint8_t port_id[3]; 64 uint8_t sequence_id; 65 66 uint16_t port_timer; 67 68 uint16_t nport_handle; /* N_PORT handle. */ 69 70 uint16_t receive_data_size; 71 uint16_t reserved_2; 72 73 uint8_t prli_svc_param_word_0[2]; /* Big endian */ 74 /* Bits 15-0 of word 0 */ 75 uint8_t prli_svc_param_word_3[2]; /* Big endian */ 76 /* Bits 15-0 of word 3 */ 77 78 uint8_t port_name[WWN_SIZE]; 79 uint8_t node_name[WWN_SIZE]; 80 81 uint8_t reserved_3[4]; 82 uint16_t prli_nvme_svc_param_word_0; /* Bits 15-0 of word 0 */ 83 uint16_t prli_nvme_svc_param_word_3; /* Bits 15-0 of word 3 */ 84 uint16_t nvme_first_burst_size; 85 uint8_t reserved_4[14]; 86 }; 87 88 /* 89 * MB 75h returns a list of DB entries similar to port_database_24xx(64B). 90 * However, in this case it returns 1st 40 bytes. 91 */ 92 struct get_name_list_extended { 93 __le16 flags; 94 u8 current_login_state; 95 u8 last_login_state; 96 u8 hard_address[3]; 97 u8 reserved_1; 98 u8 port_id[3]; 99 u8 sequence_id; 100 __le16 port_timer; 101 __le16 nport_handle; /* N_PORT handle. */ 102 __le16 receive_data_size; 103 __le16 reserved_2; 104 105 /* PRLI SVC Param are Big endian */ 106 u8 prli_svc_param_word_0[2]; /* Bits 15-0 of word 0 */ 107 u8 prli_svc_param_word_3[2]; /* Bits 15-0 of word 3 */ 108 u8 port_name[WWN_SIZE]; 109 u8 node_name[WWN_SIZE]; 110 }; 111 112 /* MB 75h: This is the short version of the database */ 113 struct get_name_list { 114 u8 port_node_name[WWN_SIZE]; /* B7 most sig, B0 least sig */ 115 __le16 nport_handle; 116 u8 reserved; 117 }; 118 119 struct vp_database_24xx { 120 uint16_t vp_status; 121 uint8_t options; 122 uint8_t id; 123 uint8_t port_name[WWN_SIZE]; 124 uint8_t node_name[WWN_SIZE]; 125 uint16_t port_id_low; 126 uint16_t port_id_high; 127 }; 128 129 struct nvram_24xx { 130 /* NVRAM header. */ 131 uint8_t id[4]; 132 uint16_t nvram_version; 133 uint16_t reserved_0; 134 135 /* Firmware Initialization Control Block. */ 136 uint16_t version; 137 uint16_t reserved_1; 138 __le16 frame_payload_size; 139 uint16_t execution_throttle; 140 uint16_t exchange_count; 141 uint16_t hard_address; 142 143 uint8_t port_name[WWN_SIZE]; 144 uint8_t node_name[WWN_SIZE]; 145 146 uint16_t login_retry_count; 147 uint16_t link_down_on_nos; 148 uint16_t interrupt_delay_timer; 149 uint16_t login_timeout; 150 151 uint32_t firmware_options_1; 152 uint32_t firmware_options_2; 153 uint32_t firmware_options_3; 154 155 /* Offset 56. */ 156 157 /* 158 * BIT 0 = Control Enable 159 * BIT 1-15 = 160 * 161 * BIT 0-7 = Reserved 162 * BIT 8-10 = Output Swing 1G 163 * BIT 11-13 = Output Emphasis 1G 164 * BIT 14-15 = Reserved 165 * 166 * BIT 0-7 = Reserved 167 * BIT 8-10 = Output Swing 2G 168 * BIT 11-13 = Output Emphasis 2G 169 * BIT 14-15 = Reserved 170 * 171 * BIT 0-7 = Reserved 172 * BIT 8-10 = Output Swing 4G 173 * BIT 11-13 = Output Emphasis 4G 174 * BIT 14-15 = Reserved 175 */ 176 uint16_t seriallink_options[4]; 177 178 uint16_t reserved_2[16]; 179 180 /* Offset 96. */ 181 uint16_t reserved_3[16]; 182 183 /* PCIe table entries. */ 184 uint16_t reserved_4[16]; 185 186 /* Offset 160. */ 187 uint16_t reserved_5[16]; 188 189 /* Offset 192. */ 190 uint16_t reserved_6[16]; 191 192 /* Offset 224. */ 193 uint16_t reserved_7[16]; 194 195 /* 196 * BIT 0 = Enable spinup delay 197 * BIT 1 = Disable BIOS 198 * BIT 2 = Enable Memory Map BIOS 199 * BIT 3 = Enable Selectable Boot 200 * BIT 4 = Disable RISC code load 201 * BIT 5 = Disable Serdes 202 * BIT 6 = 203 * BIT 7 = 204 * 205 * BIT 8 = 206 * BIT 9 = 207 * BIT 10 = Enable lip full login 208 * BIT 11 = Enable target reset 209 * BIT 12 = 210 * BIT 13 = 211 * BIT 14 = 212 * BIT 15 = Enable alternate WWN 213 * 214 * BIT 16-31 = 215 */ 216 uint32_t host_p; 217 218 uint8_t alternate_port_name[WWN_SIZE]; 219 uint8_t alternate_node_name[WWN_SIZE]; 220 221 uint8_t boot_port_name[WWN_SIZE]; 222 uint16_t boot_lun_number; 223 uint16_t reserved_8; 224 225 uint8_t alt1_boot_port_name[WWN_SIZE]; 226 uint16_t alt1_boot_lun_number; 227 uint16_t reserved_9; 228 229 uint8_t alt2_boot_port_name[WWN_SIZE]; 230 uint16_t alt2_boot_lun_number; 231 uint16_t reserved_10; 232 233 uint8_t alt3_boot_port_name[WWN_SIZE]; 234 uint16_t alt3_boot_lun_number; 235 uint16_t reserved_11; 236 237 /* 238 * BIT 0 = Selective Login 239 * BIT 1 = Alt-Boot Enable 240 * BIT 2 = Reserved 241 * BIT 3 = Boot Order List 242 * BIT 4 = Reserved 243 * BIT 5 = Selective LUN 244 * BIT 6 = Reserved 245 * BIT 7-31 = 246 */ 247 uint32_t efi_parameters; 248 249 uint8_t reset_delay; 250 uint8_t reserved_12; 251 uint16_t reserved_13; 252 253 uint16_t boot_id_number; 254 uint16_t reserved_14; 255 256 uint16_t max_luns_per_target; 257 uint16_t reserved_15; 258 259 uint16_t port_down_retry_count; 260 uint16_t link_down_timeout; 261 262 /* FCode parameters. */ 263 uint16_t fcode_parameter; 264 265 uint16_t reserved_16[3]; 266 267 /* Offset 352. */ 268 uint8_t prev_drv_ver_major; 269 uint8_t prev_drv_ver_submajob; 270 uint8_t prev_drv_ver_minor; 271 uint8_t prev_drv_ver_subminor; 272 273 uint16_t prev_bios_ver_major; 274 uint16_t prev_bios_ver_minor; 275 276 uint16_t prev_efi_ver_major; 277 uint16_t prev_efi_ver_minor; 278 279 uint16_t prev_fw_ver_major; 280 uint8_t prev_fw_ver_minor; 281 uint8_t prev_fw_ver_subminor; 282 283 uint16_t reserved_17[8]; 284 285 /* Offset 384. */ 286 uint16_t reserved_18[16]; 287 288 /* Offset 416. */ 289 uint16_t reserved_19[16]; 290 291 /* Offset 448. */ 292 uint16_t reserved_20[16]; 293 294 /* Offset 480. */ 295 uint8_t model_name[16]; 296 297 uint16_t reserved_21[2]; 298 299 /* Offset 500. */ 300 /* HW Parameter Block. */ 301 uint16_t pcie_table_sig; 302 uint16_t pcie_table_offset; 303 304 uint16_t subsystem_vendor_id; 305 uint16_t subsystem_device_id; 306 307 uint32_t checksum; 308 }; 309 310 /* 311 * ISP Initialization Control Block. 312 * Little endian except where noted. 313 */ 314 #define ICB_VERSION 1 315 struct init_cb_24xx { 316 uint16_t version; 317 uint16_t reserved_1; 318 319 uint16_t frame_payload_size; 320 uint16_t execution_throttle; 321 uint16_t exchange_count; 322 323 uint16_t hard_address; 324 325 uint8_t port_name[WWN_SIZE]; /* Big endian. */ 326 uint8_t node_name[WWN_SIZE]; /* Big endian. */ 327 328 uint16_t response_q_inpointer; 329 uint16_t request_q_outpointer; 330 331 uint16_t login_retry_count; 332 333 uint16_t prio_request_q_outpointer; 334 335 uint16_t response_q_length; 336 uint16_t request_q_length; 337 338 uint16_t link_down_on_nos; /* Milliseconds. */ 339 340 uint16_t prio_request_q_length; 341 342 uint32_t request_q_address[2]; 343 uint32_t response_q_address[2]; 344 uint32_t prio_request_q_address[2]; 345 346 uint16_t msix; 347 uint16_t msix_atio; 348 uint8_t reserved_2[4]; 349 350 uint16_t atio_q_inpointer; 351 uint16_t atio_q_length; 352 uint32_t atio_q_address[2]; 353 354 uint16_t interrupt_delay_timer; /* 100us increments. */ 355 uint16_t login_timeout; 356 357 /* 358 * BIT 0 = Enable Hard Loop Id 359 * BIT 1 = Enable Fairness 360 * BIT 2 = Enable Full-Duplex 361 * BIT 3 = Reserved 362 * BIT 4 = Enable Target Mode 363 * BIT 5 = Disable Initiator Mode 364 * BIT 6 = Acquire FA-WWN 365 * BIT 7 = Enable D-port Diagnostics 366 * 367 * BIT 8 = Reserved 368 * BIT 9 = Non Participating LIP 369 * BIT 10 = Descending Loop ID Search 370 * BIT 11 = Acquire Loop ID in LIPA 371 * BIT 12 = Reserved 372 * BIT 13 = Full Login after LIP 373 * BIT 14 = Node Name Option 374 * BIT 15-31 = Reserved 375 */ 376 uint32_t firmware_options_1; 377 378 /* 379 * BIT 0 = Operation Mode bit 0 380 * BIT 1 = Operation Mode bit 1 381 * BIT 2 = Operation Mode bit 2 382 * BIT 3 = Operation Mode bit 3 383 * BIT 4 = Connection Options bit 0 384 * BIT 5 = Connection Options bit 1 385 * BIT 6 = Connection Options bit 2 386 * BIT 7 = Enable Non part on LIHA failure 387 * 388 * BIT 8 = Enable Class 2 389 * BIT 9 = Enable ACK0 390 * BIT 10 = Reserved 391 * BIT 11 = Enable FC-SP Security 392 * BIT 12 = FC Tape Enable 393 * BIT 13 = Reserved 394 * BIT 14 = Enable Target PRLI Control 395 * BIT 15-31 = Reserved 396 */ 397 uint32_t firmware_options_2; 398 399 /* 400 * BIT 0 = Reserved 401 * BIT 1 = Soft ID only 402 * BIT 2 = Reserved 403 * BIT 3 = Reserved 404 * BIT 4 = FCP RSP Payload bit 0 405 * BIT 5 = FCP RSP Payload bit 1 406 * BIT 6 = Enable Receive Out-of-Order data frame handling 407 * BIT 7 = Disable Automatic PLOGI on Local Loop 408 * 409 * BIT 8 = Reserved 410 * BIT 9 = Enable Out-of-Order FCP_XFER_RDY relative offset handling 411 * BIT 10 = Reserved 412 * BIT 11 = Reserved 413 * BIT 12 = Reserved 414 * BIT 13 = Data Rate bit 0 415 * BIT 14 = Data Rate bit 1 416 * BIT 15 = Data Rate bit 2 417 * BIT 16 = Enable 75 ohm Termination Select 418 * BIT 17-28 = Reserved 419 * BIT 29 = Enable response queue 0 in index shadowing 420 * BIT 30 = Enable request queue 0 out index shadowing 421 * BIT 31 = Reserved 422 */ 423 uint32_t firmware_options_3; 424 uint16_t qos; 425 uint16_t rid; 426 uint8_t reserved_3[20]; 427 }; 428 429 /* 430 * ISP queue - command entry structure definition. 431 */ 432 #define COMMAND_BIDIRECTIONAL 0x75 433 struct cmd_bidir { 434 uint8_t entry_type; /* Entry type. */ 435 uint8_t entry_count; /* Entry count. */ 436 uint8_t sys_define; /* System defined */ 437 uint8_t entry_status; /* Entry status. */ 438 439 uint32_t handle; /* System handle. */ 440 441 uint16_t nport_handle; /* N_PORT hanlde. */ 442 443 uint16_t timeout; /* Commnad timeout. */ 444 445 uint16_t wr_dseg_count; /* Write Data segment count. */ 446 uint16_t rd_dseg_count; /* Read Data segment count. */ 447 448 struct scsi_lun lun; /* FCP LUN (BE). */ 449 450 uint16_t control_flags; /* Control flags. */ 451 #define BD_WRAP_BACK BIT_3 452 #define BD_READ_DATA BIT_1 453 #define BD_WRITE_DATA BIT_0 454 455 uint16_t fcp_cmnd_dseg_len; /* Data segment length. */ 456 uint32_t fcp_cmnd_dseg_address[2]; /* Data segment address. */ 457 458 uint16_t reserved[2]; /* Reserved */ 459 460 uint32_t rd_byte_count; /* Total Byte count Read. */ 461 uint32_t wr_byte_count; /* Total Byte count write. */ 462 463 uint8_t port_id[3]; /* PortID of destination port.*/ 464 uint8_t vp_index; 465 466 uint32_t fcp_data_dseg_address[2]; /* Data segment address. */ 467 uint16_t fcp_data_dseg_len; /* Data segment length. */ 468 }; 469 470 #define COMMAND_TYPE_6 0x48 /* Command Type 6 entry */ 471 struct cmd_type_6 { 472 uint8_t entry_type; /* Entry type. */ 473 uint8_t entry_count; /* Entry count. */ 474 uint8_t sys_define; /* System defined. */ 475 uint8_t entry_status; /* Entry Status. */ 476 477 uint32_t handle; /* System handle. */ 478 479 uint16_t nport_handle; /* N_PORT handle. */ 480 uint16_t timeout; /* Command timeout. */ 481 482 uint16_t dseg_count; /* Data segment count. */ 483 484 uint16_t fcp_rsp_dsd_len; /* FCP_RSP DSD length. */ 485 486 struct scsi_lun lun; /* FCP LUN (BE). */ 487 488 uint16_t control_flags; /* Control flags. */ 489 #define CF_DIF_SEG_DESCR_ENABLE BIT_3 490 #define CF_DATA_SEG_DESCR_ENABLE BIT_2 491 #define CF_READ_DATA BIT_1 492 #define CF_WRITE_DATA BIT_0 493 494 uint16_t fcp_cmnd_dseg_len; /* Data segment length. */ 495 uint32_t fcp_cmnd_dseg_address[2]; /* Data segment address. */ 496 497 uint32_t fcp_rsp_dseg_address[2]; /* Data segment address. */ 498 499 uint32_t byte_count; /* Total byte count. */ 500 501 uint8_t port_id[3]; /* PortID of destination port. */ 502 uint8_t vp_index; 503 504 uint32_t fcp_data_dseg_address[2]; /* Data segment address. */ 505 uint32_t fcp_data_dseg_len; /* Data segment length. */ 506 }; 507 508 #define COMMAND_TYPE_7 0x18 /* Command Type 7 entry */ 509 struct cmd_type_7 { 510 uint8_t entry_type; /* Entry type. */ 511 uint8_t entry_count; /* Entry count. */ 512 uint8_t sys_define; /* System defined. */ 513 uint8_t entry_status; /* Entry Status. */ 514 515 uint32_t handle; /* System handle. */ 516 517 uint16_t nport_handle; /* N_PORT handle. */ 518 uint16_t timeout; /* Command timeout. */ 519 #define FW_MAX_TIMEOUT 0x1999 520 521 uint16_t dseg_count; /* Data segment count. */ 522 uint16_t reserved_1; 523 524 struct scsi_lun lun; /* FCP LUN (BE). */ 525 526 uint16_t task_mgmt_flags; /* Task management flags. */ 527 #define TMF_CLEAR_ACA BIT_14 528 #define TMF_TARGET_RESET BIT_13 529 #define TMF_LUN_RESET BIT_12 530 #define TMF_CLEAR_TASK_SET BIT_10 531 #define TMF_ABORT_TASK_SET BIT_9 532 #define TMF_DSD_LIST_ENABLE BIT_2 533 #define TMF_READ_DATA BIT_1 534 #define TMF_WRITE_DATA BIT_0 535 536 uint8_t task; 537 #define TSK_SIMPLE 0 538 #define TSK_HEAD_OF_QUEUE 1 539 #define TSK_ORDERED 2 540 #define TSK_ACA 4 541 #define TSK_UNTAGGED 5 542 543 uint8_t crn; 544 545 uint8_t fcp_cdb[MAX_CMDSZ]; /* SCSI command words. */ 546 uint32_t byte_count; /* Total byte count. */ 547 548 uint8_t port_id[3]; /* PortID of destination port. */ 549 uint8_t vp_index; 550 551 uint32_t dseg_0_address[2]; /* Data segment 0 address. */ 552 uint32_t dseg_0_len; /* Data segment 0 length. */ 553 }; 554 555 #define COMMAND_TYPE_CRC_2 0x6A /* Command Type CRC_2 (Type 6) 556 * (T10-DIF) */ 557 struct cmd_type_crc_2 { 558 uint8_t entry_type; /* Entry type. */ 559 uint8_t entry_count; /* Entry count. */ 560 uint8_t sys_define; /* System defined. */ 561 uint8_t entry_status; /* Entry Status. */ 562 563 uint32_t handle; /* System handle. */ 564 565 uint16_t nport_handle; /* N_PORT handle. */ 566 uint16_t timeout; /* Command timeout. */ 567 568 uint16_t dseg_count; /* Data segment count. */ 569 570 uint16_t fcp_rsp_dseg_len; /* FCP_RSP DSD length. */ 571 572 struct scsi_lun lun; /* FCP LUN (BE). */ 573 574 uint16_t control_flags; /* Control flags. */ 575 576 uint16_t fcp_cmnd_dseg_len; /* Data segment length. */ 577 uint32_t fcp_cmnd_dseg_address[2]; /* Data segment address. */ 578 579 uint32_t fcp_rsp_dseg_address[2]; /* Data segment address. */ 580 581 uint32_t byte_count; /* Total byte count. */ 582 583 uint8_t port_id[3]; /* PortID of destination port. */ 584 uint8_t vp_index; 585 586 uint32_t crc_context_address[2]; /* Data segment address. */ 587 uint16_t crc_context_len; /* Data segment length. */ 588 uint16_t reserved_1; /* MUST be set to 0. */ 589 }; 590 591 592 /* 593 * ISP queue - status entry structure definition. 594 */ 595 #define STATUS_TYPE 0x03 /* Status entry. */ 596 struct sts_entry_24xx { 597 uint8_t entry_type; /* Entry type. */ 598 uint8_t entry_count; /* Entry count. */ 599 uint8_t sys_define; /* System defined. */ 600 uint8_t entry_status; /* Entry Status. */ 601 602 uint32_t handle; /* System handle. */ 603 604 uint16_t comp_status; /* Completion status. */ 605 uint16_t ox_id; /* OX_ID used by the firmware. */ 606 607 uint32_t residual_len; /* FW calc residual transfer length. */ 608 609 union { 610 uint16_t reserved_1; 611 uint16_t nvme_rsp_pyld_len; 612 }; 613 614 uint16_t state_flags; /* State flags. */ 615 #define SF_TRANSFERRED_DATA BIT_11 616 #define SF_NVME_ERSP BIT_6 617 #define SF_FCP_RSP_DMA BIT_0 618 619 uint16_t retry_delay; 620 uint16_t scsi_status; /* SCSI status. */ 621 #define SS_CONFIRMATION_REQ BIT_12 622 623 uint32_t rsp_residual_count; /* FCP RSP residual count. */ 624 625 uint32_t sense_len; /* FCP SENSE length. */ 626 627 union { 628 struct { 629 uint32_t rsp_data_len; /* FCP response data length */ 630 uint8_t data[28]; /* FCP rsp/sense information */ 631 }; 632 struct nvme_fc_ersp_iu nvme_ersp; 633 uint8_t nvme_ersp_data[32]; 634 }; 635 636 /* 637 * If DIF Error is set in comp_status, these additional fields are 638 * defined: 639 * 640 * !!! NOTE: Firmware sends expected/actual DIF data in big endian 641 * format; but all of the "data" field gets swab32-d in the beginning 642 * of qla2x00_status_entry(). 643 * 644 * &data[10] : uint8_t report_runt_bg[2]; - computed guard 645 * &data[12] : uint8_t actual_dif[8]; - DIF Data received 646 * &data[20] : uint8_t expected_dif[8]; - DIF Data computed 647 */ 648 }; 649 650 651 /* 652 * Status entry completion status 653 */ 654 #define CS_DATA_REASSEMBLY_ERROR 0x11 /* Data Reassembly Error.. */ 655 #define CS_ABTS_BY_TARGET 0x13 /* Target send ABTS to abort IOCB. */ 656 #define CS_FW_RESOURCE 0x2C /* Firmware Resource Unavailable. */ 657 #define CS_TASK_MGMT_OVERRUN 0x30 /* Task management overrun (8+). */ 658 #define CS_ABORT_BY_TARGET 0x47 /* Abort By Target. */ 659 660 /* 661 * ISP queue - marker entry structure definition. 662 */ 663 #define MARKER_TYPE 0x04 /* Marker entry. */ 664 struct mrk_entry_24xx { 665 uint8_t entry_type; /* Entry type. */ 666 uint8_t entry_count; /* Entry count. */ 667 uint8_t handle_count; /* Handle count. */ 668 uint8_t entry_status; /* Entry Status. */ 669 670 uint32_t handle; /* System handle. */ 671 672 uint16_t nport_handle; /* N_PORT handle. */ 673 674 uint8_t modifier; /* Modifier (7-0). */ 675 #define MK_SYNC_ID_LUN 0 /* Synchronize ID/LUN */ 676 #define MK_SYNC_ID 1 /* Synchronize ID */ 677 #define MK_SYNC_ALL 2 /* Synchronize all ID/LUN */ 678 uint8_t reserved_1; 679 680 uint8_t reserved_2; 681 uint8_t vp_index; 682 683 uint16_t reserved_3; 684 685 uint8_t lun[8]; /* FCP LUN (BE). */ 686 uint8_t reserved_4[40]; 687 }; 688 689 /* 690 * ISP queue - CT Pass-Through entry structure definition. 691 */ 692 #define CT_IOCB_TYPE 0x29 /* CT Pass-Through IOCB entry */ 693 struct ct_entry_24xx { 694 uint8_t entry_type; /* Entry type. */ 695 uint8_t entry_count; /* Entry count. */ 696 uint8_t sys_define; /* System Defined. */ 697 uint8_t entry_status; /* Entry Status. */ 698 699 uint32_t handle; /* System handle. */ 700 701 uint16_t comp_status; /* Completion status. */ 702 703 uint16_t nport_handle; /* N_PORT handle. */ 704 705 uint16_t cmd_dsd_count; 706 707 uint8_t vp_index; 708 uint8_t reserved_1; 709 710 uint16_t timeout; /* Command timeout. */ 711 uint16_t reserved_2; 712 713 uint16_t rsp_dsd_count; 714 715 uint8_t reserved_3[10]; 716 717 uint32_t rsp_byte_count; 718 uint32_t cmd_byte_count; 719 720 uint32_t dseg_0_address[2]; /* Data segment 0 address. */ 721 uint32_t dseg_0_len; /* Data segment 0 length. */ 722 uint32_t dseg_1_address[2]; /* Data segment 1 address. */ 723 uint32_t dseg_1_len; /* Data segment 1 length. */ 724 }; 725 726 /* 727 * ISP queue - ELS Pass-Through entry structure definition. 728 */ 729 #define ELS_IOCB_TYPE 0x53 /* ELS Pass-Through IOCB entry */ 730 struct els_entry_24xx { 731 uint8_t entry_type; /* Entry type. */ 732 uint8_t entry_count; /* Entry count. */ 733 uint8_t sys_define; /* System Defined. */ 734 uint8_t entry_status; /* Entry Status. */ 735 736 uint32_t handle; /* System handle. */ 737 738 uint16_t reserved_1; 739 740 uint16_t nport_handle; /* N_PORT handle. */ 741 742 uint16_t tx_dsd_count; 743 744 uint8_t vp_index; 745 uint8_t sof_type; 746 #define EST_SOFI3 (1 << 4) 747 #define EST_SOFI2 (3 << 4) 748 749 uint32_t rx_xchg_address; /* Receive exchange address. */ 750 uint16_t rx_dsd_count; 751 752 uint8_t opcode; 753 uint8_t reserved_2; 754 755 uint8_t port_id[3]; 756 uint8_t s_id[3]; 757 758 uint16_t control_flags; /* Control flags. */ 759 #define ECF_PAYLOAD_DESCR_MASK (BIT_15|BIT_14|BIT_13) 760 #define EPD_ELS_COMMAND (0 << 13) 761 #define EPD_ELS_ACC (1 << 13) 762 #define EPD_ELS_RJT (2 << 13) 763 #define EPD_RX_XCHG (3 << 13) 764 #define ECF_CLR_PASSTHRU_PEND BIT_12 765 #define ECF_INCL_FRAME_HDR BIT_11 766 767 uint32_t rx_byte_count; 768 uint32_t tx_byte_count; 769 770 uint32_t tx_address[2]; /* Data segment 0 address. */ 771 uint32_t tx_len; /* Data segment 0 length. */ 772 uint32_t rx_address[2]; /* Data segment 1 address. */ 773 uint32_t rx_len; /* Data segment 1 length. */ 774 }; 775 776 struct els_sts_entry_24xx { 777 uint8_t entry_type; /* Entry type. */ 778 uint8_t entry_count; /* Entry count. */ 779 uint8_t sys_define; /* System Defined. */ 780 uint8_t entry_status; /* Entry Status. */ 781 782 uint32_t handle; /* System handle. */ 783 784 uint16_t comp_status; 785 786 uint16_t nport_handle; /* N_PORT handle. */ 787 788 uint16_t reserved_1; 789 790 uint8_t vp_index; 791 uint8_t sof_type; 792 793 uint32_t rx_xchg_address; /* Receive exchange address. */ 794 uint16_t reserved_2; 795 796 uint8_t opcode; 797 uint8_t reserved_3; 798 799 uint8_t port_id[3]; 800 uint8_t reserved_4; 801 802 uint16_t reserved_5; 803 804 uint16_t control_flags; /* Control flags. */ 805 uint32_t total_byte_count; 806 uint32_t error_subcode_1; 807 uint32_t error_subcode_2; 808 }; 809 /* 810 * ISP queue - Mailbox Command entry structure definition. 811 */ 812 #define MBX_IOCB_TYPE 0x39 813 struct mbx_entry_24xx { 814 uint8_t entry_type; /* Entry type. */ 815 uint8_t entry_count; /* Entry count. */ 816 uint8_t handle_count; /* Handle count. */ 817 uint8_t entry_status; /* Entry Status. */ 818 819 uint32_t handle; /* System handle. */ 820 821 uint16_t mbx[28]; 822 }; 823 824 825 #define LOGINOUT_PORT_IOCB_TYPE 0x52 /* Login/Logout Port entry. */ 826 struct logio_entry_24xx { 827 uint8_t entry_type; /* Entry type. */ 828 uint8_t entry_count; /* Entry count. */ 829 uint8_t sys_define; /* System defined. */ 830 uint8_t entry_status; /* Entry Status. */ 831 832 uint32_t handle; /* System handle. */ 833 834 uint16_t comp_status; /* Completion status. */ 835 #define CS_LOGIO_ERROR 0x31 /* Login/Logout IOCB error. */ 836 837 uint16_t nport_handle; /* N_PORT handle. */ 838 839 uint16_t control_flags; /* Control flags. */ 840 /* Modifiers. */ 841 #define LCF_INCLUDE_SNS BIT_10 /* Include SNS (FFFFFC) during LOGO. */ 842 #define LCF_FCP2_OVERRIDE BIT_9 /* Set/Reset word 3 of PRLI. */ 843 #define LCF_CLASS_2 BIT_8 /* Enable class 2 during PLOGI. */ 844 #define LCF_FREE_NPORT BIT_7 /* Release NPORT handle after LOGO. */ 845 #define LCF_EXPL_LOGO BIT_6 /* Perform an explicit LOGO. */ 846 #define LCF_NVME_PRLI BIT_6 /* Perform NVME FC4 PRLI */ 847 #define LCF_SKIP_PRLI BIT_5 /* Skip PRLI after PLOGI. */ 848 #define LCF_IMPL_LOGO_ALL BIT_5 /* Implicit LOGO to all ports. */ 849 #define LCF_COND_PLOGI BIT_4 /* PLOGI only if not logged-in. */ 850 #define LCF_IMPL_LOGO BIT_4 /* Perform an implicit LOGO. */ 851 #define LCF_IMPL_PRLO BIT_4 /* Perform an implicit PRLO. */ 852 /* Commands. */ 853 #define LCF_COMMAND_PLOGI 0x00 /* PLOGI. */ 854 #define LCF_COMMAND_PRLI 0x01 /* PRLI. */ 855 #define LCF_COMMAND_PDISC 0x02 /* PDISC. */ 856 #define LCF_COMMAND_ADISC 0x03 /* ADISC. */ 857 #define LCF_COMMAND_LOGO 0x08 /* LOGO. */ 858 #define LCF_COMMAND_PRLO 0x09 /* PRLO. */ 859 #define LCF_COMMAND_TPRLO 0x0A /* TPRLO. */ 860 861 uint8_t vp_index; 862 uint8_t reserved_1; 863 864 uint8_t port_id[3]; /* PortID of destination port. */ 865 866 uint8_t rsp_size; /* Response size in 32bit words. */ 867 868 uint32_t io_parameter[11]; /* General I/O parameters. */ 869 #define LSC_SCODE_NOLINK 0x01 870 #define LSC_SCODE_NOIOCB 0x02 871 #define LSC_SCODE_NOXCB 0x03 872 #define LSC_SCODE_CMD_FAILED 0x04 873 #define LSC_SCODE_NOFABRIC 0x05 874 #define LSC_SCODE_FW_NOT_READY 0x07 875 #define LSC_SCODE_NOT_LOGGED_IN 0x09 876 #define LSC_SCODE_NOPCB 0x0A 877 878 #define LSC_SCODE_ELS_REJECT 0x18 879 #define LSC_SCODE_CMD_PARAM_ERR 0x19 880 #define LSC_SCODE_PORTID_USED 0x1A 881 #define LSC_SCODE_NPORT_USED 0x1B 882 #define LSC_SCODE_NONPORT 0x1C 883 #define LSC_SCODE_LOGGED_IN 0x1D 884 #define LSC_SCODE_NOFLOGI_ACC 0x1F 885 }; 886 887 #define TSK_MGMT_IOCB_TYPE 0x14 888 struct tsk_mgmt_entry { 889 uint8_t entry_type; /* Entry type. */ 890 uint8_t entry_count; /* Entry count. */ 891 uint8_t handle_count; /* Handle count. */ 892 uint8_t entry_status; /* Entry Status. */ 893 894 uint32_t handle; /* System handle. */ 895 896 uint16_t nport_handle; /* N_PORT handle. */ 897 898 uint16_t reserved_1; 899 900 uint16_t delay; /* Activity delay in seconds. */ 901 902 uint16_t timeout; /* Command timeout. */ 903 904 struct scsi_lun lun; /* FCP LUN (BE). */ 905 906 uint32_t control_flags; /* Control Flags. */ 907 #define TCF_NOTMCMD_TO_TARGET BIT_31 908 #define TCF_LUN_RESET BIT_4 909 #define TCF_ABORT_TASK_SET BIT_3 910 #define TCF_CLEAR_TASK_SET BIT_2 911 #define TCF_TARGET_RESET BIT_1 912 #define TCF_CLEAR_ACA BIT_0 913 914 uint8_t reserved_2[20]; 915 916 uint8_t port_id[3]; /* PortID of destination port. */ 917 uint8_t vp_index; 918 919 uint8_t reserved_3[12]; 920 }; 921 922 #define ABORT_IOCB_TYPE 0x33 923 struct abort_entry_24xx { 924 uint8_t entry_type; /* Entry type. */ 925 uint8_t entry_count; /* Entry count. */ 926 uint8_t handle_count; /* Handle count. */ 927 uint8_t entry_status; /* Entry Status. */ 928 929 uint32_t handle; /* System handle. */ 930 931 uint16_t nport_handle; /* N_PORT handle. */ 932 /* or Completion status. */ 933 934 uint16_t options; /* Options. */ 935 #define AOF_NO_ABTS BIT_0 /* Do not send any ABTS. */ 936 937 uint32_t handle_to_abort; /* System handle to abort. */ 938 939 uint16_t req_que_no; 940 uint8_t reserved_1[30]; 941 942 uint8_t port_id[3]; /* PortID of destination port. */ 943 uint8_t vp_index; 944 945 uint8_t reserved_2[12]; 946 }; 947 948 /* 949 * ISP I/O Register Set structure definitions. 950 */ 951 struct device_reg_24xx { 952 uint32_t flash_addr; /* Flash/NVRAM BIOS address. */ 953 #define FARX_DATA_FLAG BIT_31 954 #define FARX_ACCESS_FLASH_CONF 0x7FFD0000 955 #define FARX_ACCESS_FLASH_DATA 0x7FF00000 956 #define FARX_ACCESS_NVRAM_CONF 0x7FFF0000 957 #define FARX_ACCESS_NVRAM_DATA 0x7FFE0000 958 959 #define FA_NVRAM_FUNC0_ADDR 0x80 960 #define FA_NVRAM_FUNC1_ADDR 0x180 961 962 #define FA_NVRAM_VPD_SIZE 0x200 963 #define FA_NVRAM_VPD0_ADDR 0x00 964 #define FA_NVRAM_VPD1_ADDR 0x100 965 966 #define FA_BOOT_CODE_ADDR 0x00000 967 /* 968 * RISC code begins at offset 512KB 969 * within flash. Consisting of two 970 * contiguous RISC code segments. 971 */ 972 #define FA_RISC_CODE_ADDR 0x20000 973 #define FA_RISC_CODE_SEGMENTS 2 974 975 #define FA_FLASH_DESCR_ADDR_24 0x11000 976 #define FA_FLASH_LAYOUT_ADDR_24 0x11400 977 #define FA_NPIV_CONF0_ADDR_24 0x16000 978 #define FA_NPIV_CONF1_ADDR_24 0x17000 979 980 #define FA_FW_AREA_ADDR 0x40000 981 #define FA_VPD_NVRAM_ADDR 0x48000 982 #define FA_FEATURE_ADDR 0x4C000 983 #define FA_FLASH_DESCR_ADDR 0x50000 984 #define FA_FLASH_LAYOUT_ADDR 0x50400 985 #define FA_HW_EVENT0_ADDR 0x54000 986 #define FA_HW_EVENT1_ADDR 0x54400 987 #define FA_HW_EVENT_SIZE 0x200 988 #define FA_HW_EVENT_ENTRY_SIZE 4 989 #define FA_NPIV_CONF0_ADDR 0x5C000 990 #define FA_NPIV_CONF1_ADDR 0x5D000 991 #define FA_FCP_PRIO0_ADDR 0x10000 992 #define FA_FCP_PRIO1_ADDR 0x12000 993 994 /* 995 * Flash Error Log Event Codes. 996 */ 997 #define HW_EVENT_RESET_ERR 0xF00B 998 #define HW_EVENT_ISP_ERR 0xF020 999 #define HW_EVENT_PARITY_ERR 0xF022 1000 #define HW_EVENT_NVRAM_CHKSUM_ERR 0xF023 1001 #define HW_EVENT_FLASH_FW_ERR 0xF024 1002 1003 uint32_t flash_data; /* Flash/NVRAM BIOS data. */ 1004 1005 uint32_t ctrl_status; /* Control/Status. */ 1006 #define CSRX_FLASH_ACCESS_ERROR BIT_18 /* Flash/NVRAM Access Error. */ 1007 #define CSRX_DMA_ACTIVE BIT_17 /* DMA Active status. */ 1008 #define CSRX_DMA_SHUTDOWN BIT_16 /* DMA Shutdown control status. */ 1009 #define CSRX_FUNCTION BIT_15 /* Function number. */ 1010 /* PCI-X Bus Mode. */ 1011 #define CSRX_PCIX_BUS_MODE_MASK (BIT_11|BIT_10|BIT_9|BIT_8) 1012 #define PBM_PCI_33MHZ (0 << 8) 1013 #define PBM_PCIX_M1_66MHZ (1 << 8) 1014 #define PBM_PCIX_M1_100MHZ (2 << 8) 1015 #define PBM_PCIX_M1_133MHZ (3 << 8) 1016 #define PBM_PCIX_M2_66MHZ (5 << 8) 1017 #define PBM_PCIX_M2_100MHZ (6 << 8) 1018 #define PBM_PCIX_M2_133MHZ (7 << 8) 1019 #define PBM_PCI_66MHZ (8 << 8) 1020 /* Max Write Burst byte count. */ 1021 #define CSRX_MAX_WRT_BURST_MASK (BIT_5|BIT_4) 1022 #define MWB_512_BYTES (0 << 4) 1023 #define MWB_1024_BYTES (1 << 4) 1024 #define MWB_2048_BYTES (2 << 4) 1025 #define MWB_4096_BYTES (3 << 4) 1026 1027 #define CSRX_64BIT_SLOT BIT_2 /* PCI 64-Bit Bus Slot. */ 1028 #define CSRX_FLASH_ENABLE BIT_1 /* Flash BIOS Read/Write enable. */ 1029 #define CSRX_ISP_SOFT_RESET BIT_0 /* ISP soft reset. */ 1030 1031 uint32_t ictrl; /* Interrupt control. */ 1032 #define ICRX_EN_RISC_INT BIT_3 /* Enable RISC interrupts on PCI. */ 1033 1034 uint32_t istatus; /* Interrupt status. */ 1035 #define ISRX_RISC_INT BIT_3 /* RISC interrupt. */ 1036 1037 uint32_t unused_1[2]; /* Gap. */ 1038 1039 /* Request Queue. */ 1040 uint32_t req_q_in; /* In-Pointer. */ 1041 uint32_t req_q_out; /* Out-Pointer. */ 1042 /* Response Queue. */ 1043 uint32_t rsp_q_in; /* In-Pointer. */ 1044 uint32_t rsp_q_out; /* Out-Pointer. */ 1045 /* Priority Request Queue. */ 1046 uint32_t preq_q_in; /* In-Pointer. */ 1047 uint32_t preq_q_out; /* Out-Pointer. */ 1048 1049 uint32_t unused_2[2]; /* Gap. */ 1050 1051 /* ATIO Queue. */ 1052 uint32_t atio_q_in; /* In-Pointer. */ 1053 uint32_t atio_q_out; /* Out-Pointer. */ 1054 1055 uint32_t host_status; 1056 #define HSRX_RISC_INT BIT_15 /* RISC to Host interrupt. */ 1057 #define HSRX_RISC_PAUSED BIT_8 /* RISC Paused. */ 1058 1059 uint32_t hccr; /* Host command & control register. */ 1060 /* HCCR statuses. */ 1061 #define HCCRX_HOST_INT BIT_6 /* Host to RISC interrupt bit. */ 1062 #define HCCRX_RISC_RESET BIT_5 /* RISC Reset mode bit. */ 1063 /* HCCR commands. */ 1064 /* NOOP. */ 1065 #define HCCRX_NOOP 0x00000000 1066 /* Set RISC Reset. */ 1067 #define HCCRX_SET_RISC_RESET 0x10000000 1068 /* Clear RISC Reset. */ 1069 #define HCCRX_CLR_RISC_RESET 0x20000000 1070 /* Set RISC Pause. */ 1071 #define HCCRX_SET_RISC_PAUSE 0x30000000 1072 /* Releases RISC Pause. */ 1073 #define HCCRX_REL_RISC_PAUSE 0x40000000 1074 /* Set HOST to RISC interrupt. */ 1075 #define HCCRX_SET_HOST_INT 0x50000000 1076 /* Clear HOST to RISC interrupt. */ 1077 #define HCCRX_CLR_HOST_INT 0x60000000 1078 /* Clear RISC to PCI interrupt. */ 1079 #define HCCRX_CLR_RISC_INT 0xA0000000 1080 1081 uint32_t gpiod; /* GPIO Data register. */ 1082 1083 /* LED update mask. */ 1084 #define GPDX_LED_UPDATE_MASK (BIT_20|BIT_19|BIT_18) 1085 /* Data update mask. */ 1086 #define GPDX_DATA_UPDATE_MASK (BIT_17|BIT_16) 1087 /* Data update mask. */ 1088 #define GPDX_DATA_UPDATE_2_MASK (BIT_28|BIT_27|BIT_26|BIT_17|BIT_16) 1089 /* LED control mask. */ 1090 #define GPDX_LED_COLOR_MASK (BIT_4|BIT_3|BIT_2) 1091 /* LED bit values. Color names as 1092 * referenced in fw spec. 1093 */ 1094 #define GPDX_LED_YELLOW_ON BIT_2 1095 #define GPDX_LED_GREEN_ON BIT_3 1096 #define GPDX_LED_AMBER_ON BIT_4 1097 /* Data in/out. */ 1098 #define GPDX_DATA_INOUT (BIT_1|BIT_0) 1099 1100 uint32_t gpioe; /* GPIO Enable register. */ 1101 /* Enable update mask. */ 1102 #define GPEX_ENABLE_UPDATE_MASK (BIT_17|BIT_16) 1103 /* Enable update mask. */ 1104 #define GPEX_ENABLE_UPDATE_2_MASK (BIT_28|BIT_27|BIT_26|BIT_17|BIT_16) 1105 /* Enable. */ 1106 #define GPEX_ENABLE (BIT_1|BIT_0) 1107 1108 uint32_t iobase_addr; /* I/O Bus Base Address register. */ 1109 1110 uint32_t unused_3[10]; /* Gap. */ 1111 1112 uint16_t mailbox0; 1113 uint16_t mailbox1; 1114 uint16_t mailbox2; 1115 uint16_t mailbox3; 1116 uint16_t mailbox4; 1117 uint16_t mailbox5; 1118 uint16_t mailbox6; 1119 uint16_t mailbox7; 1120 uint16_t mailbox8; 1121 uint16_t mailbox9; 1122 uint16_t mailbox10; 1123 uint16_t mailbox11; 1124 uint16_t mailbox12; 1125 uint16_t mailbox13; 1126 uint16_t mailbox14; 1127 uint16_t mailbox15; 1128 uint16_t mailbox16; 1129 uint16_t mailbox17; 1130 uint16_t mailbox18; 1131 uint16_t mailbox19; 1132 uint16_t mailbox20; 1133 uint16_t mailbox21; 1134 uint16_t mailbox22; 1135 uint16_t mailbox23; 1136 uint16_t mailbox24; 1137 uint16_t mailbox25; 1138 uint16_t mailbox26; 1139 uint16_t mailbox27; 1140 uint16_t mailbox28; 1141 uint16_t mailbox29; 1142 uint16_t mailbox30; 1143 uint16_t mailbox31; 1144 1145 uint32_t iobase_window; 1146 uint32_t iobase_c4; 1147 uint32_t iobase_c8; 1148 uint32_t unused_4_1[6]; /* Gap. */ 1149 uint32_t iobase_q; 1150 uint32_t unused_5[2]; /* Gap. */ 1151 uint32_t iobase_select; 1152 uint32_t unused_6[2]; /* Gap. */ 1153 uint32_t iobase_sdata; 1154 }; 1155 /* RISC-RISC semaphore register PCI offet */ 1156 #define RISC_REGISTER_BASE_OFFSET 0x7010 1157 #define RISC_REGISTER_WINDOW_OFFET 0x6 1158 1159 /* RISC-RISC semaphore/flag register (risc address 0x7016) */ 1160 1161 #define RISC_SEMAPHORE 0x1UL 1162 #define RISC_SEMAPHORE_WE (RISC_SEMAPHORE << 16) 1163 #define RISC_SEMAPHORE_CLR (RISC_SEMAPHORE_WE | 0x0UL) 1164 #define RISC_SEMAPHORE_SET (RISC_SEMAPHORE_WE | RISC_SEMAPHORE) 1165 1166 #define RISC_SEMAPHORE_FORCE 0x8000UL 1167 #define RISC_SEMAPHORE_FORCE_WE (RISC_SEMAPHORE_FORCE << 16) 1168 #define RISC_SEMAPHORE_FORCE_CLR (RISC_SEMAPHORE_FORCE_WE | 0x0UL) 1169 #define RISC_SEMAPHORE_FORCE_SET \ 1170 (RISC_SEMAPHORE_FORCE_WE | RISC_SEMAPHORE_FORCE) 1171 1172 /* RISC semaphore timeouts (ms) */ 1173 #define TIMEOUT_SEMAPHORE 2500 1174 #define TIMEOUT_SEMAPHORE_FORCE 2000 1175 #define TIMEOUT_TOTAL_ELAPSED 4500 1176 1177 /* Trace Control *************************************************************/ 1178 1179 #define TC_AEN_DISABLE 0 1180 1181 #define TC_EFT_ENABLE 4 1182 #define TC_EFT_DISABLE 5 1183 1184 #define TC_FCE_ENABLE 8 1185 #define TC_FCE_OPTIONS 0 1186 #define TC_FCE_DEFAULT_RX_SIZE 2112 1187 #define TC_FCE_DEFAULT_TX_SIZE 2112 1188 #define TC_FCE_DISABLE 9 1189 #define TC_FCE_DISABLE_TRACE BIT_0 1190 1191 /* MID Support ***************************************************************/ 1192 1193 #define MIN_MULTI_ID_FABRIC 64 /* Must be power-of-2. */ 1194 #define MAX_MULTI_ID_FABRIC 256 /* ... */ 1195 1196 struct mid_conf_entry_24xx { 1197 uint16_t reserved_1; 1198 1199 /* 1200 * BIT 0 = Enable Hard Loop Id 1201 * BIT 1 = Acquire Loop ID in LIPA 1202 * BIT 2 = ID not Acquired 1203 * BIT 3 = Enable VP 1204 * BIT 4 = Enable Initiator Mode 1205 * BIT 5 = Disable Target Mode 1206 * BIT 6-7 = Reserved 1207 */ 1208 uint8_t options; 1209 1210 uint8_t hard_address; 1211 1212 uint8_t port_name[WWN_SIZE]; 1213 uint8_t node_name[WWN_SIZE]; 1214 }; 1215 1216 struct mid_init_cb_24xx { 1217 struct init_cb_24xx init_cb; 1218 1219 uint16_t count; 1220 uint16_t options; 1221 1222 struct mid_conf_entry_24xx entries[MAX_MULTI_ID_FABRIC]; 1223 }; 1224 1225 1226 struct mid_db_entry_24xx { 1227 uint16_t status; 1228 #define MDBS_NON_PARTIC BIT_3 1229 #define MDBS_ID_ACQUIRED BIT_1 1230 #define MDBS_ENABLED BIT_0 1231 1232 uint8_t options; 1233 uint8_t hard_address; 1234 1235 uint8_t port_name[WWN_SIZE]; 1236 uint8_t node_name[WWN_SIZE]; 1237 1238 uint8_t port_id[3]; 1239 uint8_t reserved_1; 1240 }; 1241 1242 /* 1243 * Virtual Port Control IOCB 1244 */ 1245 #define VP_CTRL_IOCB_TYPE 0x30 /* Virtual Port Control entry. */ 1246 struct vp_ctrl_entry_24xx { 1247 uint8_t entry_type; /* Entry type. */ 1248 uint8_t entry_count; /* Entry count. */ 1249 uint8_t sys_define; /* System defined. */ 1250 uint8_t entry_status; /* Entry Status. */ 1251 1252 uint32_t handle; /* System handle. */ 1253 1254 uint16_t vp_idx_failed; 1255 1256 uint16_t comp_status; /* Completion status. */ 1257 #define CS_VCE_IOCB_ERROR 0x01 /* Error processing IOCB */ 1258 #define CS_VCE_ACQ_ID_ERROR 0x02 /* Error while acquireing ID. */ 1259 #define CS_VCE_BUSY 0x05 /* Firmware not ready to accept cmd. */ 1260 1261 uint16_t command; 1262 #define VCE_COMMAND_ENABLE_VPS 0x00 /* Enable VPs. */ 1263 #define VCE_COMMAND_DISABLE_VPS 0x08 /* Disable VPs. */ 1264 #define VCE_COMMAND_DISABLE_VPS_REINIT 0x09 /* Disable VPs and reinit link. */ 1265 #define VCE_COMMAND_DISABLE_VPS_LOGO 0x0a /* Disable VPs and LOGO ports. */ 1266 #define VCE_COMMAND_DISABLE_VPS_LOGO_ALL 0x0b /* Disable VPs and LOGO ports. */ 1267 1268 uint16_t vp_count; 1269 1270 uint8_t vp_idx_map[16]; 1271 uint16_t flags; 1272 uint16_t id; 1273 uint16_t reserved_4; 1274 uint16_t hopct; 1275 uint8_t reserved_5[24]; 1276 }; 1277 1278 /* 1279 * Modify Virtual Port Configuration IOCB 1280 */ 1281 #define VP_CONFIG_IOCB_TYPE 0x31 /* Virtual Port Config entry. */ 1282 struct vp_config_entry_24xx { 1283 uint8_t entry_type; /* Entry type. */ 1284 uint8_t entry_count; /* Entry count. */ 1285 uint8_t handle_count; 1286 uint8_t entry_status; /* Entry Status. */ 1287 1288 uint32_t handle; /* System handle. */ 1289 1290 uint16_t flags; 1291 #define CS_VF_BIND_VPORTS_TO_VF BIT_0 1292 #define CS_VF_SET_QOS_OF_VPORTS BIT_1 1293 #define CS_VF_SET_HOPS_OF_VPORTS BIT_2 1294 1295 uint16_t comp_status; /* Completion status. */ 1296 #define CS_VCT_STS_ERROR 0x01 /* Specified VPs were not disabled. */ 1297 #define CS_VCT_CNT_ERROR 0x02 /* Invalid VP count. */ 1298 #define CS_VCT_ERROR 0x03 /* Unknown error. */ 1299 #define CS_VCT_IDX_ERROR 0x02 /* Invalid VP index. */ 1300 #define CS_VCT_BUSY 0x05 /* Firmware not ready to accept cmd. */ 1301 1302 uint8_t command; 1303 #define VCT_COMMAND_MOD_VPS 0x00 /* Modify VP configurations. */ 1304 #define VCT_COMMAND_MOD_ENABLE_VPS 0x01 /* Modify configuration & enable VPs. */ 1305 1306 uint8_t vp_count; 1307 1308 uint8_t vp_index1; 1309 uint8_t vp_index2; 1310 1311 uint8_t options_idx1; 1312 uint8_t hard_address_idx1; 1313 uint16_t reserved_vp1; 1314 uint8_t port_name_idx1[WWN_SIZE]; 1315 uint8_t node_name_idx1[WWN_SIZE]; 1316 1317 uint8_t options_idx2; 1318 uint8_t hard_address_idx2; 1319 uint16_t reserved_vp2; 1320 uint8_t port_name_idx2[WWN_SIZE]; 1321 uint8_t node_name_idx2[WWN_SIZE]; 1322 uint16_t id; 1323 uint16_t reserved_4; 1324 uint16_t hopct; 1325 uint8_t reserved_5[2]; 1326 }; 1327 1328 #define VP_RPT_ID_IOCB_TYPE 0x32 /* Report ID Acquisition entry. */ 1329 enum VP_STATUS { 1330 VP_STAT_COMPL, 1331 VP_STAT_FAIL, 1332 VP_STAT_ID_CHG, 1333 VP_STAT_SNS_TO, /* timeout */ 1334 VP_STAT_SNS_RJT, 1335 VP_STAT_SCR_TO, /* timeout */ 1336 VP_STAT_SCR_RJT, 1337 }; 1338 1339 enum VP_FLAGS { 1340 VP_FLAGS_CON_FLOOP = 1, 1341 VP_FLAGS_CON_P2P = 2, 1342 VP_FLAGS_CON_FABRIC = 3, 1343 VP_FLAGS_NAME_VALID = BIT_5, 1344 }; 1345 1346 struct vp_rpt_id_entry_24xx { 1347 uint8_t entry_type; /* Entry type. */ 1348 uint8_t entry_count; /* Entry count. */ 1349 uint8_t sys_define; /* System defined. */ 1350 uint8_t entry_status; /* Entry Status. */ 1351 uint32_t resv1; 1352 uint8_t vp_acquired; 1353 uint8_t vp_setup; 1354 uint8_t vp_idx; /* Format 0=reserved */ 1355 uint8_t vp_status; /* Format 0=reserved */ 1356 1357 uint8_t port_id[3]; 1358 uint8_t format; 1359 union { 1360 struct { 1361 /* format 0 loop */ 1362 uint8_t vp_idx_map[16]; 1363 uint8_t reserved_4[32]; 1364 } f0; 1365 struct { 1366 /* format 1 fabric */ 1367 uint8_t vpstat1_subcode; /* vp_status=1 subcode */ 1368 uint8_t flags; 1369 uint16_t fip_flags; 1370 uint8_t rsv2[12]; 1371 1372 uint8_t ls_rjt_vendor; 1373 uint8_t ls_rjt_explanation; 1374 uint8_t ls_rjt_reason; 1375 uint8_t rsv3[5]; 1376 1377 uint8_t port_name[8]; 1378 uint8_t node_name[8]; 1379 uint16_t bbcr; 1380 uint8_t reserved_5[6]; 1381 } f1; 1382 struct { /* format 2: N2N direct connect */ 1383 uint8_t vpstat1_subcode; 1384 uint8_t flags; 1385 uint16_t rsv6; 1386 uint8_t rsv2[12]; 1387 1388 uint8_t ls_rjt_vendor; 1389 uint8_t ls_rjt_explanation; 1390 uint8_t ls_rjt_reason; 1391 uint8_t rsv3[5]; 1392 1393 uint8_t port_name[8]; 1394 uint8_t node_name[8]; 1395 uint8_t remote_nport_id[4]; 1396 uint32_t reserved_5; 1397 } f2; 1398 } u; 1399 }; 1400 1401 #define VF_EVFP_IOCB_TYPE 0x26 /* Exchange Virtual Fabric Parameters entry. */ 1402 struct vf_evfp_entry_24xx { 1403 uint8_t entry_type; /* Entry type. */ 1404 uint8_t entry_count; /* Entry count. */ 1405 uint8_t sys_define; /* System defined. */ 1406 uint8_t entry_status; /* Entry Status. */ 1407 1408 uint32_t handle; /* System handle. */ 1409 uint16_t comp_status; /* Completion status. */ 1410 uint16_t timeout; /* timeout */ 1411 uint16_t adim_tagging_mode; 1412 1413 uint16_t vfport_id; 1414 uint32_t exch_addr; 1415 1416 uint16_t nport_handle; /* N_PORT handle. */ 1417 uint16_t control_flags; 1418 uint32_t io_parameter_0; 1419 uint32_t io_parameter_1; 1420 uint32_t tx_address[2]; /* Data segment 0 address. */ 1421 uint32_t tx_len; /* Data segment 0 length. */ 1422 uint32_t rx_address[2]; /* Data segment 1 address. */ 1423 uint32_t rx_len; /* Data segment 1 length. */ 1424 }; 1425 1426 /* END MID Support ***********************************************************/ 1427 1428 /* Flash Description Table ***************************************************/ 1429 1430 struct qla_fdt_layout { 1431 uint8_t sig[4]; 1432 uint16_t version; 1433 uint16_t len; 1434 uint16_t checksum; 1435 uint8_t unused1[2]; 1436 uint8_t model[16]; 1437 uint16_t man_id; 1438 uint16_t id; 1439 uint8_t flags; 1440 uint8_t erase_cmd; 1441 uint8_t alt_erase_cmd; 1442 uint8_t wrt_enable_cmd; 1443 uint8_t wrt_enable_bits; 1444 uint8_t wrt_sts_reg_cmd; 1445 uint8_t unprotect_sec_cmd; 1446 uint8_t read_man_id_cmd; 1447 uint32_t block_size; 1448 uint32_t alt_block_size; 1449 uint32_t flash_size; 1450 uint32_t wrt_enable_data; 1451 uint8_t read_id_addr_len; 1452 uint8_t wrt_disable_bits; 1453 uint8_t read_dev_id_len; 1454 uint8_t chip_erase_cmd; 1455 uint16_t read_timeout; 1456 uint8_t protect_sec_cmd; 1457 uint8_t unused2[65]; 1458 }; 1459 1460 /* Flash Layout Table ********************************************************/ 1461 1462 struct qla_flt_location { 1463 uint8_t sig[4]; 1464 uint16_t start_lo; 1465 uint16_t start_hi; 1466 uint8_t version; 1467 uint8_t unused[5]; 1468 uint16_t checksum; 1469 }; 1470 1471 struct qla_flt_header { 1472 uint16_t version; 1473 uint16_t length; 1474 uint16_t checksum; 1475 uint16_t unused; 1476 }; 1477 1478 #define FLT_REG_FW 0x01 1479 #define FLT_REG_BOOT_CODE 0x07 1480 #define FLT_REG_VPD_0 0x14 1481 #define FLT_REG_NVRAM_0 0x15 1482 #define FLT_REG_VPD_1 0x16 1483 #define FLT_REG_NVRAM_1 0x17 1484 #define FLT_REG_VPD_2 0xD4 1485 #define FLT_REG_NVRAM_2 0xD5 1486 #define FLT_REG_VPD_3 0xD6 1487 #define FLT_REG_NVRAM_3 0xD7 1488 #define FLT_REG_FDT 0x1a 1489 #define FLT_REG_FLT 0x1c 1490 #define FLT_REG_HW_EVENT_0 0x1d 1491 #define FLT_REG_HW_EVENT_1 0x1f 1492 #define FLT_REG_NPIV_CONF_0 0x29 1493 #define FLT_REG_NPIV_CONF_1 0x2a 1494 #define FLT_REG_GOLD_FW 0x2f 1495 #define FLT_REG_FCP_PRIO_0 0x87 1496 #define FLT_REG_FCP_PRIO_1 0x88 1497 #define FLT_REG_CNA_FW 0x97 1498 #define FLT_REG_BOOT_CODE_8044 0xA2 1499 #define FLT_REG_FCOE_FW 0xA4 1500 #define FLT_REG_FCOE_NVRAM_0 0xAA 1501 #define FLT_REG_FCOE_NVRAM_1 0xAC 1502 1503 /* 27xx */ 1504 #define FLT_REG_IMG_PRI_27XX 0x95 1505 #define FLT_REG_IMG_SEC_27XX 0x96 1506 #define FLT_REG_FW_SEC_27XX 0x02 1507 #define FLT_REG_BOOTLOAD_SEC_27XX 0x9 1508 #define FLT_REG_VPD_SEC_27XX_0 0x50 1509 #define FLT_REG_VPD_SEC_27XX_1 0x52 1510 #define FLT_REG_VPD_SEC_27XX_2 0xD8 1511 #define FLT_REG_VPD_SEC_27XX_3 0xDA 1512 1513 struct qla_flt_region { 1514 uint32_t code; 1515 uint32_t size; 1516 uint32_t start; 1517 uint32_t end; 1518 }; 1519 1520 /* Flash NPIV Configuration Table ********************************************/ 1521 1522 struct qla_npiv_header { 1523 uint8_t sig[2]; 1524 uint16_t version; 1525 uint16_t entries; 1526 uint16_t unused[4]; 1527 uint16_t checksum; 1528 }; 1529 1530 struct qla_npiv_entry { 1531 uint16_t flags; 1532 uint16_t vf_id; 1533 uint8_t q_qos; 1534 uint8_t f_qos; 1535 uint16_t unused1; 1536 uint8_t port_name[WWN_SIZE]; 1537 uint8_t node_name[WWN_SIZE]; 1538 }; 1539 1540 /* 84XX Support **************************************************************/ 1541 1542 #define MBA_ISP84XX_ALERT 0x800f /* Alert Notification. */ 1543 #define A84_PANIC_RECOVERY 0x1 1544 #define A84_OP_LOGIN_COMPLETE 0x2 1545 #define A84_DIAG_LOGIN_COMPLETE 0x3 1546 #define A84_GOLD_LOGIN_COMPLETE 0x4 1547 1548 #define MBC_ISP84XX_RESET 0x3a /* Reset. */ 1549 1550 #define FSTATE_REMOTE_FC_DOWN BIT_0 1551 #define FSTATE_NSL_LINK_DOWN BIT_1 1552 #define FSTATE_IS_DIAG_FW BIT_2 1553 #define FSTATE_LOGGED_IN BIT_3 1554 #define FSTATE_WAITING_FOR_VERIFY BIT_4 1555 1556 #define VERIFY_CHIP_IOCB_TYPE 0x1B 1557 struct verify_chip_entry_84xx { 1558 uint8_t entry_type; 1559 uint8_t entry_count; 1560 uint8_t sys_defined; 1561 uint8_t entry_status; 1562 1563 uint32_t handle; 1564 1565 uint16_t options; 1566 #define VCO_DONT_UPDATE_FW BIT_0 1567 #define VCO_FORCE_UPDATE BIT_1 1568 #define VCO_DONT_RESET_UPDATE BIT_2 1569 #define VCO_DIAG_FW BIT_3 1570 #define VCO_END_OF_DATA BIT_14 1571 #define VCO_ENABLE_DSD BIT_15 1572 1573 uint16_t reserved_1; 1574 1575 uint16_t data_seg_cnt; 1576 uint16_t reserved_2[3]; 1577 1578 uint32_t fw_ver; 1579 uint32_t exchange_address; 1580 1581 uint32_t reserved_3[3]; 1582 uint32_t fw_size; 1583 uint32_t fw_seq_size; 1584 uint32_t relative_offset; 1585 1586 uint32_t dseg_address[2]; 1587 uint32_t dseg_length; 1588 }; 1589 1590 struct verify_chip_rsp_84xx { 1591 uint8_t entry_type; 1592 uint8_t entry_count; 1593 uint8_t sys_defined; 1594 uint8_t entry_status; 1595 1596 uint32_t handle; 1597 1598 uint16_t comp_status; 1599 #define CS_VCS_CHIP_FAILURE 0x3 1600 #define CS_VCS_BAD_EXCHANGE 0x8 1601 #define CS_VCS_SEQ_COMPLETEi 0x40 1602 1603 uint16_t failure_code; 1604 #define VFC_CHECKSUM_ERROR 0x1 1605 #define VFC_INVALID_LEN 0x2 1606 #define VFC_ALREADY_IN_PROGRESS 0x8 1607 1608 uint16_t reserved_1[4]; 1609 1610 uint32_t fw_ver; 1611 uint32_t exchange_address; 1612 1613 uint32_t reserved_2[6]; 1614 }; 1615 1616 #define ACCESS_CHIP_IOCB_TYPE 0x2B 1617 struct access_chip_84xx { 1618 uint8_t entry_type; 1619 uint8_t entry_count; 1620 uint8_t sys_defined; 1621 uint8_t entry_status; 1622 1623 uint32_t handle; 1624 1625 uint16_t options; 1626 #define ACO_DUMP_MEMORY 0x0 1627 #define ACO_LOAD_MEMORY 0x1 1628 #define ACO_CHANGE_CONFIG_PARAM 0x2 1629 #define ACO_REQUEST_INFO 0x3 1630 1631 uint16_t reserved1; 1632 1633 uint16_t dseg_count; 1634 uint16_t reserved2[3]; 1635 1636 uint32_t parameter1; 1637 uint32_t parameter2; 1638 uint32_t parameter3; 1639 1640 uint32_t reserved3[3]; 1641 uint32_t total_byte_cnt; 1642 uint32_t reserved4; 1643 1644 uint32_t dseg_address[2]; 1645 uint32_t dseg_length; 1646 }; 1647 1648 struct access_chip_rsp_84xx { 1649 uint8_t entry_type; 1650 uint8_t entry_count; 1651 uint8_t sys_defined; 1652 uint8_t entry_status; 1653 1654 uint32_t handle; 1655 1656 uint16_t comp_status; 1657 uint16_t failure_code; 1658 uint32_t residual_count; 1659 1660 uint32_t reserved[12]; 1661 }; 1662 1663 /* 81XX Support **************************************************************/ 1664 1665 #define MBA_DCBX_START 0x8016 1666 #define MBA_DCBX_COMPLETE 0x8030 1667 #define MBA_FCF_CONF_ERR 0x8031 1668 #define MBA_DCBX_PARAM_UPDATE 0x8032 1669 #define MBA_IDC_COMPLETE 0x8100 1670 #define MBA_IDC_NOTIFY 0x8101 1671 #define MBA_IDC_TIME_EXT 0x8102 1672 1673 #define MBC_IDC_ACK 0x101 1674 #define MBC_RESTART_MPI_FW 0x3d 1675 #define MBC_FLASH_ACCESS_CTRL 0x3e /* Control flash access. */ 1676 #define MBC_GET_XGMAC_STATS 0x7a 1677 #define MBC_GET_DCBX_PARAMS 0x51 1678 1679 /* 1680 * ISP83xx mailbox commands 1681 */ 1682 #define MBC_WRITE_REMOTE_REG 0x0001 /* Write remote register */ 1683 #define MBC_READ_REMOTE_REG 0x0009 /* Read remote register */ 1684 #define MBC_RESTART_NIC_FIRMWARE 0x003d /* Restart NIC firmware */ 1685 #define MBC_SET_ACCESS_CONTROL 0x003e /* Access control command */ 1686 1687 /* Flash access control option field bit definitions */ 1688 #define FAC_OPT_FORCE_SEMAPHORE BIT_15 1689 #define FAC_OPT_REQUESTOR_ID BIT_14 1690 #define FAC_OPT_CMD_SUBCODE 0xff 1691 1692 /* Flash access control command subcodes */ 1693 #define FAC_OPT_CMD_WRITE_PROTECT 0x00 1694 #define FAC_OPT_CMD_WRITE_ENABLE 0x01 1695 #define FAC_OPT_CMD_ERASE_SECTOR 0x02 1696 #define FAC_OPT_CMD_LOCK_SEMAPHORE 0x03 1697 #define FAC_OPT_CMD_UNLOCK_SEMAPHORE 0x04 1698 #define FAC_OPT_CMD_GET_SECTOR_SIZE 0x05 1699 1700 /* enhanced features bit definitions */ 1701 #define NEF_LR_DIST_ENABLE BIT_0 1702 1703 /* LR Distance bit positions */ 1704 #define LR_DIST_NV_POS 2 1705 #define LR_DIST_FW_POS 12 1706 #define LR_DIST_FW_SHIFT (LR_DIST_FW_POS - LR_DIST_NV_POS) 1707 #define LR_DIST_FW_FIELD(x) ((x) << LR_DIST_FW_SHIFT & 0xf000) 1708 1709 struct nvram_81xx { 1710 /* NVRAM header. */ 1711 uint8_t id[4]; 1712 uint16_t nvram_version; 1713 uint16_t reserved_0; 1714 1715 /* Firmware Initialization Control Block. */ 1716 uint16_t version; 1717 uint16_t reserved_1; 1718 uint16_t frame_payload_size; 1719 uint16_t execution_throttle; 1720 uint16_t exchange_count; 1721 uint16_t reserved_2; 1722 1723 uint8_t port_name[WWN_SIZE]; 1724 uint8_t node_name[WWN_SIZE]; 1725 1726 uint16_t login_retry_count; 1727 uint16_t reserved_3; 1728 uint16_t interrupt_delay_timer; 1729 uint16_t login_timeout; 1730 1731 uint32_t firmware_options_1; 1732 uint32_t firmware_options_2; 1733 uint32_t firmware_options_3; 1734 1735 uint16_t reserved_4[4]; 1736 1737 /* Offset 64. */ 1738 uint8_t enode_mac[6]; 1739 uint16_t reserved_5[5]; 1740 1741 /* Offset 80. */ 1742 uint16_t reserved_6[24]; 1743 1744 /* Offset 128. */ 1745 uint16_t ex_version; 1746 uint8_t prio_fcf_matching_flags; 1747 uint8_t reserved_6_1[3]; 1748 uint16_t pri_fcf_vlan_id; 1749 uint8_t pri_fcf_fabric_name[8]; 1750 uint16_t reserved_6_2[7]; 1751 uint8_t spma_mac_addr[6]; 1752 uint16_t reserved_6_3[14]; 1753 1754 /* Offset 192. */ 1755 uint8_t min_link_speed; 1756 uint8_t reserved_7_0; 1757 uint16_t reserved_7[31]; 1758 1759 /* 1760 * BIT 0 = Enable spinup delay 1761 * BIT 1 = Disable BIOS 1762 * BIT 2 = Enable Memory Map BIOS 1763 * BIT 3 = Enable Selectable Boot 1764 * BIT 4 = Disable RISC code load 1765 * BIT 5 = Disable Serdes 1766 * BIT 6 = Opt boot mode 1767 * BIT 7 = Interrupt enable 1768 * 1769 * BIT 8 = EV Control enable 1770 * BIT 9 = Enable lip reset 1771 * BIT 10 = Enable lip full login 1772 * BIT 11 = Enable target reset 1773 * BIT 12 = Stop firmware 1774 * BIT 13 = Enable nodename option 1775 * BIT 14 = Default WWPN valid 1776 * BIT 15 = Enable alternate WWN 1777 * 1778 * BIT 16 = CLP LUN string 1779 * BIT 17 = CLP Target string 1780 * BIT 18 = CLP BIOS enable string 1781 * BIT 19 = CLP Serdes string 1782 * BIT 20 = CLP WWPN string 1783 * BIT 21 = CLP WWNN string 1784 * BIT 22 = 1785 * BIT 23 = 1786 * BIT 24 = Keep WWPN 1787 * BIT 25 = Temp WWPN 1788 * BIT 26-31 = 1789 */ 1790 uint32_t host_p; 1791 1792 uint8_t alternate_port_name[WWN_SIZE]; 1793 uint8_t alternate_node_name[WWN_SIZE]; 1794 1795 uint8_t boot_port_name[WWN_SIZE]; 1796 uint16_t boot_lun_number; 1797 uint16_t reserved_8; 1798 1799 uint8_t alt1_boot_port_name[WWN_SIZE]; 1800 uint16_t alt1_boot_lun_number; 1801 uint16_t reserved_9; 1802 1803 uint8_t alt2_boot_port_name[WWN_SIZE]; 1804 uint16_t alt2_boot_lun_number; 1805 uint16_t reserved_10; 1806 1807 uint8_t alt3_boot_port_name[WWN_SIZE]; 1808 uint16_t alt3_boot_lun_number; 1809 uint16_t reserved_11; 1810 1811 /* 1812 * BIT 0 = Selective Login 1813 * BIT 1 = Alt-Boot Enable 1814 * BIT 2 = Reserved 1815 * BIT 3 = Boot Order List 1816 * BIT 4 = Reserved 1817 * BIT 5 = Selective LUN 1818 * BIT 6 = Reserved 1819 * BIT 7-31 = 1820 */ 1821 uint32_t efi_parameters; 1822 1823 uint8_t reset_delay; 1824 uint8_t reserved_12; 1825 uint16_t reserved_13; 1826 1827 uint16_t boot_id_number; 1828 uint16_t reserved_14; 1829 1830 uint16_t max_luns_per_target; 1831 uint16_t reserved_15; 1832 1833 uint16_t port_down_retry_count; 1834 uint16_t link_down_timeout; 1835 1836 /* FCode parameters. */ 1837 uint16_t fcode_parameter; 1838 1839 uint16_t reserved_16[3]; 1840 1841 /* Offset 352. */ 1842 uint8_t reserved_17[4]; 1843 uint16_t reserved_18[5]; 1844 uint8_t reserved_19[2]; 1845 uint16_t reserved_20[8]; 1846 1847 /* Offset 384. */ 1848 uint8_t reserved_21[16]; 1849 uint16_t reserved_22[3]; 1850 1851 /* Offset 406 (0x196) Enhanced Features 1852 * BIT 0 = Extended BB credits for LR 1853 * BIT 1 = Virtual Fabric Enable 1854 * BIT 2-5 = Distance Support if BIT 0 is on 1855 * BIT 6-15 = Unused 1856 */ 1857 uint16_t enhanced_features; 1858 uint16_t reserved_24[4]; 1859 1860 /* Offset 416. */ 1861 uint16_t reserved_25[32]; 1862 1863 /* Offset 480. */ 1864 uint8_t model_name[16]; 1865 1866 /* Offset 496. */ 1867 uint16_t feature_mask_l; 1868 uint16_t feature_mask_h; 1869 uint16_t reserved_26[2]; 1870 1871 uint16_t subsystem_vendor_id; 1872 uint16_t subsystem_device_id; 1873 1874 uint32_t checksum; 1875 }; 1876 1877 /* 1878 * ISP Initialization Control Block. 1879 * Little endian except where noted. 1880 */ 1881 #define ICB_VERSION 1 1882 struct init_cb_81xx { 1883 uint16_t version; 1884 uint16_t reserved_1; 1885 1886 uint16_t frame_payload_size; 1887 uint16_t execution_throttle; 1888 uint16_t exchange_count; 1889 1890 uint16_t reserved_2; 1891 1892 uint8_t port_name[WWN_SIZE]; /* Big endian. */ 1893 uint8_t node_name[WWN_SIZE]; /* Big endian. */ 1894 1895 uint16_t response_q_inpointer; 1896 uint16_t request_q_outpointer; 1897 1898 uint16_t login_retry_count; 1899 1900 uint16_t prio_request_q_outpointer; 1901 1902 uint16_t response_q_length; 1903 uint16_t request_q_length; 1904 1905 uint16_t reserved_3; 1906 1907 uint16_t prio_request_q_length; 1908 1909 uint32_t request_q_address[2]; 1910 uint32_t response_q_address[2]; 1911 uint32_t prio_request_q_address[2]; 1912 1913 uint8_t reserved_4[8]; 1914 1915 uint16_t atio_q_inpointer; 1916 uint16_t atio_q_length; 1917 uint32_t atio_q_address[2]; 1918 1919 uint16_t interrupt_delay_timer; /* 100us increments. */ 1920 uint16_t login_timeout; 1921 1922 /* 1923 * BIT 0-3 = Reserved 1924 * BIT 4 = Enable Target Mode 1925 * BIT 5 = Disable Initiator Mode 1926 * BIT 6 = Reserved 1927 * BIT 7 = Reserved 1928 * 1929 * BIT 8-13 = Reserved 1930 * BIT 14 = Node Name Option 1931 * BIT 15-31 = Reserved 1932 */ 1933 uint32_t firmware_options_1; 1934 1935 /* 1936 * BIT 0 = Operation Mode bit 0 1937 * BIT 1 = Operation Mode bit 1 1938 * BIT 2 = Operation Mode bit 2 1939 * BIT 3 = Operation Mode bit 3 1940 * BIT 4-7 = Reserved 1941 * 1942 * BIT 8 = Enable Class 2 1943 * BIT 9 = Enable ACK0 1944 * BIT 10 = Reserved 1945 * BIT 11 = Enable FC-SP Security 1946 * BIT 12 = FC Tape Enable 1947 * BIT 13 = Reserved 1948 * BIT 14 = Enable Target PRLI Control 1949 * BIT 15-31 = Reserved 1950 */ 1951 uint32_t firmware_options_2; 1952 1953 /* 1954 * BIT 0-3 = Reserved 1955 * BIT 4 = FCP RSP Payload bit 0 1956 * BIT 5 = FCP RSP Payload bit 1 1957 * BIT 6 = Enable Receive Out-of-Order data frame handling 1958 * BIT 7 = Reserved 1959 * 1960 * BIT 8 = Reserved 1961 * BIT 9 = Enable Out-of-Order FCP_XFER_RDY relative offset handling 1962 * BIT 10-16 = Reserved 1963 * BIT 17 = Enable multiple FCFs 1964 * BIT 18-20 = MAC addressing mode 1965 * BIT 21-25 = Ethernet data rate 1966 * BIT 26 = Enable ethernet header rx IOCB for ATIO q 1967 * BIT 27 = Enable ethernet header rx IOCB for response q 1968 * BIT 28 = SPMA selection bit 0 1969 * BIT 28 = SPMA selection bit 1 1970 * BIT 30-31 = Reserved 1971 */ 1972 uint32_t firmware_options_3; 1973 1974 uint8_t reserved_5[8]; 1975 1976 uint8_t enode_mac[6]; 1977 1978 uint8_t reserved_6[10]; 1979 }; 1980 1981 struct mid_init_cb_81xx { 1982 struct init_cb_81xx init_cb; 1983 1984 uint16_t count; 1985 uint16_t options; 1986 1987 struct mid_conf_entry_24xx entries[MAX_MULTI_ID_FABRIC]; 1988 }; 1989 1990 struct ex_init_cb_81xx { 1991 uint16_t ex_version; 1992 uint8_t prio_fcf_matching_flags; 1993 uint8_t reserved_1[3]; 1994 uint16_t pri_fcf_vlan_id; 1995 uint8_t pri_fcf_fabric_name[8]; 1996 uint16_t reserved_2[7]; 1997 uint8_t spma_mac_addr[6]; 1998 uint16_t reserved_3[14]; 1999 }; 2000 2001 #define FARX_ACCESS_FLASH_CONF_81XX 0x7FFD0000 2002 #define FARX_ACCESS_FLASH_DATA_81XX 0x7F800000 2003 2004 /* FCP priority config defines *************************************/ 2005 /* operations */ 2006 #define QLFC_FCP_PRIO_DISABLE 0x0 2007 #define QLFC_FCP_PRIO_ENABLE 0x1 2008 #define QLFC_FCP_PRIO_GET_CONFIG 0x2 2009 #define QLFC_FCP_PRIO_SET_CONFIG 0x3 2010 2011 struct qla_fcp_prio_entry { 2012 uint16_t flags; /* Describes parameter(s) in FCP */ 2013 /* priority entry that are valid */ 2014 #define FCP_PRIO_ENTRY_VALID 0x1 2015 #define FCP_PRIO_ENTRY_TAG_VALID 0x2 2016 #define FCP_PRIO_ENTRY_SPID_VALID 0x4 2017 #define FCP_PRIO_ENTRY_DPID_VALID 0x8 2018 #define FCP_PRIO_ENTRY_LUNB_VALID 0x10 2019 #define FCP_PRIO_ENTRY_LUNE_VALID 0x20 2020 #define FCP_PRIO_ENTRY_SWWN_VALID 0x40 2021 #define FCP_PRIO_ENTRY_DWWN_VALID 0x80 2022 uint8_t tag; /* Priority value */ 2023 uint8_t reserved; /* Reserved for future use */ 2024 uint32_t src_pid; /* Src port id. high order byte */ 2025 /* unused; -1 (wild card) */ 2026 uint32_t dst_pid; /* Src port id. high order byte */ 2027 /* unused; -1 (wild card) */ 2028 uint16_t lun_beg; /* 1st lun num of lun range. */ 2029 /* -1 (wild card) */ 2030 uint16_t lun_end; /* 2nd lun num of lun range. */ 2031 /* -1 (wild card) */ 2032 uint8_t src_wwpn[8]; /* Source WWPN: -1 (wild card) */ 2033 uint8_t dst_wwpn[8]; /* Destination WWPN: -1 (wild card) */ 2034 }; 2035 2036 struct qla_fcp_prio_cfg { 2037 uint8_t signature[4]; /* "HQOS" signature of config data */ 2038 uint16_t version; /* 1: Initial version */ 2039 uint16_t length; /* config data size in num bytes */ 2040 uint16_t checksum; /* config data bytes checksum */ 2041 uint16_t num_entries; /* Number of entries */ 2042 uint16_t size_of_entry; /* Size of each entry in num bytes */ 2043 uint8_t attributes; /* enable/disable, persistence */ 2044 #define FCP_PRIO_ATTR_DISABLE 0x0 2045 #define FCP_PRIO_ATTR_ENABLE 0x1 2046 #define FCP_PRIO_ATTR_PERSIST 0x2 2047 uint8_t reserved; /* Reserved for future use */ 2048 #define FCP_PRIO_CFG_HDR_SIZE 0x10 2049 struct qla_fcp_prio_entry entry[1]; /* fcp priority entries */ 2050 #define FCP_PRIO_CFG_ENTRY_SIZE 0x20 2051 }; 2052 2053 #define FCP_PRIO_CFG_SIZE (32*1024) /* fcp prio data per port*/ 2054 2055 /* 25XX Support ****************************************************/ 2056 #define FA_FCP_PRIO0_ADDR_25 0x3C000 2057 #define FA_FCP_PRIO1_ADDR_25 0x3E000 2058 2059 /* 81XX Flash locations -- occupies second 2MB region. */ 2060 #define FA_BOOT_CODE_ADDR_81 0x80000 2061 #define FA_RISC_CODE_ADDR_81 0xA0000 2062 #define FA_FW_AREA_ADDR_81 0xC0000 2063 #define FA_VPD_NVRAM_ADDR_81 0xD0000 2064 #define FA_VPD0_ADDR_81 0xD0000 2065 #define FA_VPD1_ADDR_81 0xD0400 2066 #define FA_NVRAM0_ADDR_81 0xD0080 2067 #define FA_NVRAM1_ADDR_81 0xD0180 2068 #define FA_FEATURE_ADDR_81 0xD4000 2069 #define FA_FLASH_DESCR_ADDR_81 0xD8000 2070 #define FA_FLASH_LAYOUT_ADDR_81 0xD8400 2071 #define FA_HW_EVENT0_ADDR_81 0xDC000 2072 #define FA_HW_EVENT1_ADDR_81 0xDC400 2073 #define FA_NPIV_CONF0_ADDR_81 0xD1000 2074 #define FA_NPIV_CONF1_ADDR_81 0xD2000 2075 2076 /* 83XX Flash locations -- occupies second 8MB region. */ 2077 #define FA_FLASH_LAYOUT_ADDR_83 0xFC400 2078 2079 #endif 2080