1 /* 2 * PMC-Sierra SPCv/ve 8088/8089 SAS/SATA based host adapters driver 3 * 4 * Copyright (c) 2008-2009 USI Co., Ltd. 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions, and the following disclaimer, 12 * without modification. 13 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 14 * substantially similar to the "NO WARRANTY" disclaimer below 15 * ("Disclaimer") and any redistribution must be conditioned upon 16 * including a substantially similar Disclaimer requirement for further 17 * binary redistribution. 18 * 3. Neither the names of the above-listed copyright holders nor the names 19 * of any contributors may be used to endorse or promote products derived 20 * from this software without specific prior written permission. 21 * 22 * Alternatively, this software may be distributed under the terms of the 23 * GNU General Public License ("GPL") version 2 as published by the Free 24 * Software Foundation. 25 * 26 * NO WARRANTY 27 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 28 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 29 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR 30 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 31 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 32 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 33 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 34 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 35 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING 36 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 37 * POSSIBILITY OF SUCH DAMAGES. 38 * 39 */ 40 41 #ifndef _PMC8001_REG_H_ 42 #define _PMC8001_REG_H_ 43 44 #include <linux/types.h> 45 #include <scsi/libsas.h> 46 47 /* for Request Opcode of IOMB */ 48 #define OPC_INB_ECHO 1 /* 0x000 */ 49 #define OPC_INB_PHYSTART 4 /* 0x004 */ 50 #define OPC_INB_PHYSTOP 5 /* 0x005 */ 51 #define OPC_INB_SSPINIIOSTART 6 /* 0x006 */ 52 #define OPC_INB_SSPINITMSTART 7 /* 0x007 */ 53 /* 0x8 RESV IN SPCv */ 54 #define OPC_INB_RSVD 8 /* 0x008 */ 55 #define OPC_INB_DEV_HANDLE_ACCEPT 9 /* 0x009 */ 56 #define OPC_INB_SSPTGTIOSTART 10 /* 0x00A */ 57 #define OPC_INB_SSPTGTRSPSTART 11 /* 0x00B */ 58 /* 0xC, 0xD, 0xE removed in SPCv */ 59 #define OPC_INB_SSP_ABORT 15 /* 0x00F */ 60 #define OPC_INB_DEREG_DEV_HANDLE 16 /* 0x010 */ 61 #define OPC_INB_GET_DEV_HANDLE 17 /* 0x011 */ 62 #define OPC_INB_SMP_REQUEST 18 /* 0x012 */ 63 /* 0x13 SMP_RESPONSE is removed in SPCv */ 64 #define OPC_INB_SMP_ABORT 20 /* 0x014 */ 65 /* 0x16 RESV IN SPCv */ 66 #define OPC_INB_RSVD1 22 /* 0x016 */ 67 #define OPC_INB_SATA_HOST_OPSTART 23 /* 0x017 */ 68 #define OPC_INB_SATA_ABORT 24 /* 0x018 */ 69 #define OPC_INB_LOCAL_PHY_CONTROL 25 /* 0x019 */ 70 /* 0x1A RESV IN SPCv */ 71 #define OPC_INB_RSVD2 26 /* 0x01A */ 72 #define OPC_INB_FW_FLASH_UPDATE 32 /* 0x020 */ 73 #define OPC_INB_GPIO 34 /* 0x022 */ 74 #define OPC_INB_SAS_DIAG_MODE_START_END 35 /* 0x023 */ 75 #define OPC_INB_SAS_DIAG_EXECUTE 36 /* 0x024 */ 76 /* 0x25 RESV IN SPCv */ 77 #define OPC_INB_RSVD3 37 /* 0x025 */ 78 #define OPC_INB_GET_TIME_STAMP 38 /* 0x026 */ 79 #define OPC_INB_PORT_CONTROL 39 /* 0x027 */ 80 #define OPC_INB_GET_NVMD_DATA 40 /* 0x028 */ 81 #define OPC_INB_SET_NVMD_DATA 41 /* 0x029 */ 82 #define OPC_INB_SET_DEVICE_STATE 42 /* 0x02A */ 83 #define OPC_INB_GET_DEVICE_STATE 43 /* 0x02B */ 84 #define OPC_INB_SET_DEV_INFO 44 /* 0x02C */ 85 /* 0x2D RESV IN SPCv */ 86 #define OPC_INB_RSVD4 45 /* 0x02D */ 87 #define OPC_INB_SGPIO_REGISTER 46 /* 0x02E */ 88 #define OPC_INB_PCIE_DIAG_EXEC 47 /* 0x02F */ 89 #define OPC_INB_SET_CONTROLLER_CONFIG 48 /* 0x030 */ 90 #define OPC_INB_GET_CONTROLLER_CONFIG 49 /* 0x031 */ 91 #define OPC_INB_REG_DEV 50 /* 0x032 */ 92 #define OPC_INB_SAS_HW_EVENT_ACK 51 /* 0x033 */ 93 #define OPC_INB_GET_DEVICE_INFO 52 /* 0x034 */ 94 #define OPC_INB_GET_PHY_PROFILE 53 /* 0x035 */ 95 #define OPC_INB_FLASH_OP_EXT 54 /* 0x036 */ 96 #define OPC_INB_SET_PHY_PROFILE 55 /* 0x037 */ 97 #define OPC_INB_KEK_MANAGEMENT 256 /* 0x100 */ 98 #define OPC_INB_DEK_MANAGEMENT 257 /* 0x101 */ 99 #define OPC_INB_SSP_INI_DIF_ENC_IO 258 /* 0x102 */ 100 #define OPC_INB_SATA_DIF_ENC_IO 259 /* 0x103 */ 101 102 /* for Response Opcode of IOMB */ 103 #define OPC_OUB_ECHO 1 /* 0x001 */ 104 #define OPC_OUB_RSVD 4 /* 0x004 */ 105 #define OPC_OUB_SSP_COMP 5 /* 0x005 */ 106 #define OPC_OUB_SMP_COMP 6 /* 0x006 */ 107 #define OPC_OUB_LOCAL_PHY_CNTRL 7 /* 0x007 */ 108 #define OPC_OUB_RSVD1 10 /* 0x00A */ 109 #define OPC_OUB_DEREG_DEV 11 /* 0x00B */ 110 #define OPC_OUB_GET_DEV_HANDLE 12 /* 0x00C */ 111 #define OPC_OUB_SATA_COMP 13 /* 0x00D */ 112 #define OPC_OUB_SATA_EVENT 14 /* 0x00E */ 113 #define OPC_OUB_SSP_EVENT 15 /* 0x00F */ 114 #define OPC_OUB_RSVD2 16 /* 0x010 */ 115 /* 0x11 - SMP_RECEIVED Notification removed in SPCv*/ 116 #define OPC_OUB_SSP_RECV_EVENT 18 /* 0x012 */ 117 #define OPC_OUB_RSVD3 19 /* 0x013 */ 118 #define OPC_OUB_FW_FLASH_UPDATE 20 /* 0x014 */ 119 #define OPC_OUB_GPIO_RESPONSE 22 /* 0x016 */ 120 #define OPC_OUB_GPIO_EVENT 23 /* 0x017 */ 121 #define OPC_OUB_GENERAL_EVENT 24 /* 0x018 */ 122 #define OPC_OUB_SSP_ABORT_RSP 26 /* 0x01A */ 123 #define OPC_OUB_SATA_ABORT_RSP 27 /* 0x01B */ 124 #define OPC_OUB_SAS_DIAG_MODE_START_END 28 /* 0x01C */ 125 #define OPC_OUB_SAS_DIAG_EXECUTE 29 /* 0x01D */ 126 #define OPC_OUB_GET_TIME_STAMP 30 /* 0x01E */ 127 #define OPC_OUB_RSVD4 31 /* 0x01F */ 128 #define OPC_OUB_PORT_CONTROL 32 /* 0x020 */ 129 #define OPC_OUB_SKIP_ENTRY 33 /* 0x021 */ 130 #define OPC_OUB_SMP_ABORT_RSP 34 /* 0x022 */ 131 #define OPC_OUB_GET_NVMD_DATA 35 /* 0x023 */ 132 #define OPC_OUB_SET_NVMD_DATA 36 /* 0x024 */ 133 #define OPC_OUB_DEVICE_HANDLE_REMOVAL 37 /* 0x025 */ 134 #define OPC_OUB_SET_DEVICE_STATE 38 /* 0x026 */ 135 #define OPC_OUB_GET_DEVICE_STATE 39 /* 0x027 */ 136 #define OPC_OUB_SET_DEV_INFO 40 /* 0x028 */ 137 #define OPC_OUB_RSVD5 41 /* 0x029 */ 138 #define OPC_OUB_HW_EVENT 1792 /* 0x700 */ 139 #define OPC_OUB_DEV_HANDLE_ARRIV 1824 /* 0x720 */ 140 #define OPC_OUB_THERM_HW_EVENT 1840 /* 0x730 */ 141 #define OPC_OUB_SGPIO_RESP 2094 /* 0x82E */ 142 #define OPC_OUB_PCIE_DIAG_EXECUTE 2095 /* 0x82F */ 143 #define OPC_OUB_DEV_REGIST 2098 /* 0x832 */ 144 #define OPC_OUB_SAS_HW_EVENT_ACK 2099 /* 0x833 */ 145 #define OPC_OUB_GET_DEVICE_INFO 2100 /* 0x834 */ 146 /* spcv specific commands */ 147 #define OPC_OUB_PHY_START_RESP 2052 /* 0x804 */ 148 #define OPC_OUB_PHY_STOP_RESP 2053 /* 0x805 */ 149 #define OPC_OUB_SET_CONTROLLER_CONFIG 2096 /* 0x830 */ 150 #define OPC_OUB_GET_CONTROLLER_CONFIG 2097 /* 0x831 */ 151 #define OPC_OUB_GET_PHY_PROFILE 2101 /* 0x835 */ 152 #define OPC_OUB_FLASH_OP_EXT 2102 /* 0x836 */ 153 #define OPC_OUB_SET_PHY_PROFILE 2103 /* 0x837 */ 154 #define OPC_OUB_KEK_MANAGEMENT_RESP 2304 /* 0x900 */ 155 #define OPC_OUB_DEK_MANAGEMENT_RESP 2305 /* 0x901 */ 156 #define OPC_OUB_SSP_COALESCED_COMP_RESP 2306 /* 0x902 */ 157 158 /* for phy start*/ 159 #define SSC_DISABLE_15 (0x01 << 16) 160 #define SSC_DISABLE_30 (0x02 << 16) 161 #define SSC_DISABLE_60 (0x04 << 16) 162 #define SAS_ASE (0x01 << 15) 163 #define SPINHOLD_DISABLE (0x00 << 14) 164 #define SPINHOLD_ENABLE (0x01 << 14) 165 #define LINKMODE_SAS (0x01 << 12) 166 #define LINKMODE_DSATA (0x02 << 12) 167 #define LINKMODE_AUTO (0x03 << 12) 168 #define LINKRATE_15 (0x01 << 8) 169 #define LINKRATE_30 (0x02 << 8) 170 #define LINKRATE_60 (0x04 << 8) 171 #define LINKRATE_120 (0x08 << 8) 172 173 /*phy_stop*/ 174 #define PHY_STOP_SUCCESS 0x00 175 #define PHY_STOP_ERR_DEVICE_ATTACHED 0x1046 176 177 /* phy_profile */ 178 #define SAS_PHY_ANALOG_SETTINGS_PAGE 0x04 179 #define PHY_DWORD_LENGTH 0xC 180 181 /* Thermal related */ 182 #define THERMAL_ENABLE 0x1 183 #define THERMAL_LOG_ENABLE 0x1 184 #define THERMAL_PAGE_CODE_7H 0x6 185 #define THERMAL_PAGE_CODE_8H 0x7 186 #define LTEMPHIL 70 187 #define RTEMPHIL 100 188 189 /* Encryption info */ 190 #define SCRATCH_PAD3_ENC_DISABLED 0x00000000 191 #define SCRATCH_PAD3_ENC_DIS_ERR 0x00000001 192 #define SCRATCH_PAD3_ENC_ENA_ERR 0x00000002 193 #define SCRATCH_PAD3_ENC_READY 0x00000003 194 #define SCRATCH_PAD3_ENC_MASK SCRATCH_PAD3_ENC_READY 195 196 #define SCRATCH_PAD3_XTS_ENABLED (1 << 14) 197 #define SCRATCH_PAD3_SMA_ENABLED (1 << 4) 198 #define SCRATCH_PAD3_SMB_ENABLED (1 << 5) 199 #define SCRATCH_PAD3_SMF_ENABLED 0 200 #define SCRATCH_PAD3_SM_MASK 0x000000F0 201 #define SCRATCH_PAD3_ERR_CODE 0x00FF0000 202 203 #define SEC_MODE_SMF 0x0 204 #define SEC_MODE_SMA 0x100 205 #define SEC_MODE_SMB 0x200 206 #define CIPHER_MODE_ECB 0x00000001 207 #define CIPHER_MODE_XTS 0x00000002 208 #define KEK_MGMT_SUBOP_KEYCARDUPDATE 0x4 209 210 /* SAS protocol timer configuration page */ 211 #define SAS_PROTOCOL_TIMER_CONFIG_PAGE 0x04 212 #define STP_MCT_TMO 32 213 #define SSP_MCT_TMO 32 214 #define SAS_MAX_OPEN_TIME 5 215 #define SMP_MAX_CONN_TIMER 0xFF 216 #define STP_FRM_TIMER 0 217 #define STP_IDLE_TIME 5 /* 5 us; controller default */ 218 #define SAS_MFD 0 219 #define SAS_OPNRJT_RTRY_INTVL 2 220 #define SAS_DOPNRJT_RTRY_TMO 128 221 #define SAS_COPNRJT_RTRY_TMO 128 222 223 #define SPCV_DOORBELL_CLEAR_TIMEOUT (30 * 50) /* 30 sec */ 224 #define SPC_DOORBELL_CLEAR_TIMEOUT (15 * 50) /* 15 sec */ 225 226 /* 227 Making ORR bigger than IT NEXUS LOSS which is 2000000us = 2 second. 228 Assuming a bigger value 3 second, 3000000/128 = 23437.5 where 128 229 is DOPNRJT_RTRY_TMO 230 */ 231 #define SAS_DOPNRJT_RTRY_THR 23438 232 #define SAS_COPNRJT_RTRY_THR 23438 233 #define SAS_MAX_AIP 0x200000 234 #define IT_NEXUS_TIMEOUT 0x7D0 235 #define PORT_RECOVERY_TIMEOUT ((IT_NEXUS_TIMEOUT/100) + 30) 236 /* Port recovery timeout, 10000 ms for PM8006 controller */ 237 #define CHIP_8006_PORT_RECOVERY_TIMEOUT 0x640000 238 239 #ifdef __LITTLE_ENDIAN_BITFIELD 240 struct sas_identify_frame_local { 241 /* Byte 0 */ 242 u8 frame_type:4; 243 u8 dev_type:3; 244 u8 _un0:1; 245 246 /* Byte 1 */ 247 u8 _un1; 248 249 /* Byte 2 */ 250 union { 251 struct { 252 u8 _un20:1; 253 u8 smp_iport:1; 254 u8 stp_iport:1; 255 u8 ssp_iport:1; 256 u8 _un247:4; 257 }; 258 u8 initiator_bits; 259 }; 260 261 /* Byte 3 */ 262 union { 263 struct { 264 u8 _un30:1; 265 u8 smp_tport:1; 266 u8 stp_tport:1; 267 u8 ssp_tport:1; 268 u8 _un347:4; 269 }; 270 u8 target_bits; 271 }; 272 273 /* Byte 4 - 11 */ 274 u8 _un4_11[8]; 275 276 /* Byte 12 - 19 */ 277 u8 sas_addr[SAS_ADDR_SIZE]; 278 279 /* Byte 20 */ 280 u8 phy_id; 281 282 u8 _un21_27[7]; 283 284 } __packed; 285 286 #elif defined(__BIG_ENDIAN_BITFIELD) 287 struct sas_identify_frame_local { 288 /* Byte 0 */ 289 u8 _un0:1; 290 u8 dev_type:3; 291 u8 frame_type:4; 292 293 /* Byte 1 */ 294 u8 _un1; 295 296 /* Byte 2 */ 297 union { 298 struct { 299 u8 _un247:4; 300 u8 ssp_iport:1; 301 u8 stp_iport:1; 302 u8 smp_iport:1; 303 u8 _un20:1; 304 }; 305 u8 initiator_bits; 306 }; 307 308 /* Byte 3 */ 309 union { 310 struct { 311 u8 _un347:4; 312 u8 ssp_tport:1; 313 u8 stp_tport:1; 314 u8 smp_tport:1; 315 u8 _un30:1; 316 }; 317 u8 target_bits; 318 }; 319 320 /* Byte 4 - 11 */ 321 u8 _un4_11[8]; 322 323 /* Byte 12 - 19 */ 324 u8 sas_addr[SAS_ADDR_SIZE]; 325 326 /* Byte 20 */ 327 u8 phy_id; 328 329 u8 _un21_27[7]; 330 } __packed; 331 #else 332 #error "Bitfield order not defined!" 333 #endif 334 335 struct mpi_msg_hdr { 336 __le32 header; /* Bits [11:0] - Message operation code */ 337 /* Bits [15:12] - Message Category */ 338 /* Bits [21:16] - Outboundqueue ID for the 339 operation completion message */ 340 /* Bits [23:22] - Reserved */ 341 /* Bits [28:24] - Buffer Count, indicates how 342 many buffer are allocated for the massage */ 343 /* Bits [30:29] - Reserved */ 344 /* Bits [31] - Message Valid bit */ 345 } __attribute__((packed, aligned(4))); 346 347 /* 348 * brief the data structure of PHY Start Command 349 * use to describe enable the phy (128 bytes) 350 */ 351 struct phy_start_req { 352 __le32 tag; 353 __le32 ase_sh_lm_slr_phyid; 354 struct sas_identify_frame_local sas_identify; /* 28 Bytes */ 355 __le32 spasti; 356 u32 reserved[21]; 357 } __attribute__((packed, aligned(4))); 358 359 /* 360 * brief the data structure of PHY Start Command 361 * use to disable the phy (128 bytes) 362 */ 363 struct phy_stop_req { 364 __le32 tag; 365 __le32 phy_id; 366 u32 reserved[29]; 367 } __attribute__((packed, aligned(4))); 368 369 /* set device bits fis - device to host */ 370 struct set_dev_bits_fis { 371 u8 fis_type; /* 0xA1*/ 372 u8 n_i_pmport; 373 /* b7 : n Bit. Notification bit. If set device needs attention. */ 374 /* b6 : i Bit. Interrupt Bit */ 375 /* b5-b4: reserved2 */ 376 /* b3-b0: PM Port */ 377 u8 status; 378 u8 error; 379 u32 _r_a; 380 } __attribute__ ((packed)); 381 /* PIO setup FIS - device to host */ 382 struct pio_setup_fis { 383 u8 fis_type; /* 0x5f */ 384 u8 i_d_pmPort; 385 /* b7 : reserved */ 386 /* b6 : i bit. Interrupt bit */ 387 /* b5 : d bit. data transfer direction. set to 1 for device to host 388 xfer */ 389 /* b4 : reserved */ 390 /* b3-b0: PM Port */ 391 u8 status; 392 u8 error; 393 u8 lbal; 394 u8 lbam; 395 u8 lbah; 396 u8 device; 397 u8 lbal_exp; 398 u8 lbam_exp; 399 u8 lbah_exp; 400 u8 _r_a; 401 u8 sector_count; 402 u8 sector_count_exp; 403 u8 _r_b; 404 u8 e_status; 405 u8 _r_c[2]; 406 u8 transfer_count; 407 } __attribute__ ((packed)); 408 409 /* 410 * brief the data structure of SATA Completion Response 411 * use to describe the sata task response (64 bytes) 412 */ 413 struct sata_completion_resp { 414 __le32 tag; 415 __le32 status; 416 __le32 param; 417 u32 sata_resp[12]; 418 } __attribute__((packed, aligned(4))); 419 420 /* 421 * brief the data structure of SAS HW Event Notification 422 * use to alert the host about the hardware event(64 bytes) 423 */ 424 /* updated outbound struct for spcv */ 425 426 struct hw_event_resp { 427 __le32 lr_status_evt_portid; 428 __le32 evt_param; 429 __le32 phyid_npip_portstate; 430 struct sas_identify_frame sas_identify; 431 struct dev_to_host_fis sata_fis; 432 } __attribute__((packed, aligned(4))); 433 434 /* 435 * brief the data structure for thermal event notification 436 */ 437 438 struct thermal_hw_event { 439 __le32 thermal_event; 440 __le32 rht_lht; 441 } __attribute__((packed, aligned(4))); 442 443 /* 444 * brief the data structure of REGISTER DEVICE Command 445 * use to describe MPI REGISTER DEVICE Command (64 bytes) 446 */ 447 448 struct reg_dev_req { 449 __le32 tag; 450 __le32 phyid_portid; 451 __le32 dtype_dlr_mcn_ir_retry; 452 __le32 firstburstsize_ITNexustimeout; 453 u8 sas_addr[SAS_ADDR_SIZE]; 454 __le32 upper_device_id; 455 u32 reserved[24]; 456 } __attribute__((packed, aligned(4))); 457 458 /* 459 * brief the data structure of DEREGISTER DEVICE Command 460 * use to request spc to remove all internal resources associated 461 * with the device id (64 bytes) 462 */ 463 464 struct dereg_dev_req { 465 __le32 tag; 466 __le32 device_id; 467 u32 reserved[29]; 468 } __attribute__((packed, aligned(4))); 469 470 /* 471 * brief the data structure of DEVICE_REGISTRATION Response 472 * use to notify the completion of the device registration (64 bytes) 473 */ 474 struct dev_reg_resp { 475 __le32 tag; 476 __le32 status; 477 __le32 device_id; 478 u32 reserved[12]; 479 } __attribute__((packed, aligned(4))); 480 481 /* 482 * brief the data structure of Local PHY Control Command 483 * use to issue PHY CONTROL to local phy (64 bytes) 484 */ 485 struct local_phy_ctl_req { 486 __le32 tag; 487 __le32 phyop_phyid; 488 u32 reserved1[29]; 489 } __attribute__((packed, aligned(4))); 490 491 /** 492 * brief the data structure of Local Phy Control Response 493 * use to describe MPI Local Phy Control Response (64 bytes) 494 */ 495 struct local_phy_ctl_resp { 496 __le32 tag; 497 __le32 phyop_phyid; 498 __le32 status; 499 u32 reserved[12]; 500 } __attribute__((packed, aligned(4))); 501 502 #define OP_BITS 0x0000FF00 503 #define ID_BITS 0x000000FF 504 505 /* 506 * brief the data structure of PORT Control Command 507 * use to control port properties (64 bytes) 508 */ 509 510 struct port_ctl_req { 511 __le32 tag; 512 __le32 portop_portid; 513 __le32 param0; 514 __le32 param1; 515 u32 reserved1[27]; 516 } __attribute__((packed, aligned(4))); 517 518 /* 519 * brief the data structure of HW Event Ack Command 520 * use to acknowledge receive HW event (64 bytes) 521 */ 522 struct hw_event_ack_req { 523 __le32 tag; 524 __le32 phyid_sea_portid; 525 __le32 param0; 526 __le32 param1; 527 u32 reserved1[27]; 528 } __attribute__((packed, aligned(4))); 529 530 /* 531 * brief the data structure of PHY_START Response Command 532 * indicates the completion of PHY_START command (64 bytes) 533 */ 534 struct phy_start_resp { 535 __le32 tag; 536 __le32 status; 537 __le32 phyid; 538 u32 reserved[12]; 539 } __attribute__((packed, aligned(4))); 540 541 /* 542 * brief the data structure of PHY_STOP Response Command 543 * indicates the completion of PHY_STOP command (64 bytes) 544 */ 545 struct phy_stop_resp { 546 __le32 tag; 547 __le32 status; 548 __le32 phyid; 549 u32 reserved[12]; 550 } __attribute__((packed, aligned(4))); 551 552 /* 553 * brief the data structure of SSP Completion Response 554 * use to indicate a SSP Completion (n bytes) 555 */ 556 struct ssp_completion_resp { 557 __le32 tag; 558 __le32 status; 559 __le32 param; 560 __le32 ssptag_rescv_rescpad; 561 struct ssp_response_iu ssp_resp_iu; 562 __le32 residual_count; 563 } __attribute__((packed, aligned(4))); 564 565 #define SSP_RESCV_BIT 0x00010000 566 567 /* 568 * brief the data structure of SATA EVNET response 569 * use to indicate a SATA Completion (64 bytes) 570 */ 571 struct sata_event_resp { 572 __le32 tag; 573 __le32 event; 574 __le32 port_id; 575 __le32 device_id; 576 u32 reserved; 577 __le32 event_param0; 578 __le32 event_param1; 579 __le32 sata_addr_h32; 580 __le32 sata_addr_l32; 581 __le32 e_udt1_udt0_crc; 582 __le32 e_udt5_udt4_udt3_udt2; 583 __le32 a_udt1_udt0_crc; 584 __le32 a_udt5_udt4_udt3_udt2; 585 __le32 hwdevid_diferr; 586 __le32 err_framelen_byteoffset; 587 __le32 err_dataframe; 588 } __attribute__((packed, aligned(4))); 589 590 /* 591 * brief the data structure of SSP EVNET esponse 592 * use to indicate a SSP Completion (64 bytes) 593 */ 594 struct ssp_event_resp { 595 __le32 tag; 596 __le32 event; 597 __le32 port_id; 598 __le32 device_id; 599 __le32 ssp_tag; 600 __le32 event_param0; 601 __le32 event_param1; 602 __le32 sas_addr_h32; 603 __le32 sas_addr_l32; 604 __le32 e_udt1_udt0_crc; 605 __le32 e_udt5_udt4_udt3_udt2; 606 __le32 a_udt1_udt0_crc; 607 __le32 a_udt5_udt4_udt3_udt2; 608 __le32 hwdevid_diferr; 609 __le32 err_framelen_byteoffset; 610 __le32 err_dataframe; 611 } __attribute__((packed, aligned(4))); 612 613 /** 614 * brief the data structure of General Event Notification Response 615 * use to describe MPI General Event Notification Response (64 bytes) 616 */ 617 struct general_event_resp { 618 __le32 status; 619 __le32 inb_IOMB_payload[14]; 620 } __attribute__((packed, aligned(4))); 621 622 #define GENERAL_EVENT_PAYLOAD 14 623 #define OPCODE_BITS 0x00000fff 624 625 /* 626 * brief the data structure of SMP Request Command 627 * use to describe MPI SMP REQUEST Command (64 bytes) 628 */ 629 struct smp_req { 630 __le32 tag; 631 __le32 device_id; 632 __le32 len_ip_ir; 633 /* Bits [0] - Indirect response */ 634 /* Bits [1] - Indirect Payload */ 635 /* Bits [15:2] - Reserved */ 636 /* Bits [23:16] - direct payload Len */ 637 /* Bits [31:24] - Reserved */ 638 u8 smp_req16[16]; 639 union { 640 u8 smp_req[32]; 641 struct { 642 __le64 long_req_addr;/* sg dma address, LE */ 643 __le32 long_req_size;/* LE */ 644 u32 _r_a; 645 __le64 long_resp_addr;/* sg dma address, LE */ 646 __le32 long_resp_size;/* LE */ 647 u32 _r_b; 648 } long_smp_req;/* sequencer extension */ 649 }; 650 __le32 rsvd[16]; 651 } __attribute__((packed, aligned(4))); 652 /* 653 * brief the data structure of SMP Completion Response 654 * use to describe MPI SMP Completion Response (64 bytes) 655 */ 656 struct smp_completion_resp { 657 __le32 tag; 658 __le32 status; 659 __le32 param; 660 u8 _r_a[252]; 661 } __attribute__((packed, aligned(4))); 662 663 /* 664 *brief the data structure of SSP SMP SATA Abort Command 665 * use to describe MPI SSP SMP & SATA Abort Command (64 bytes) 666 */ 667 struct task_abort_req { 668 __le32 tag; 669 __le32 device_id; 670 __le32 tag_to_abort; 671 __le32 abort_all; 672 u32 reserved[27]; 673 } __attribute__((packed, aligned(4))); 674 675 /* These flags used for SSP SMP & SATA Abort */ 676 #define ABORT_MASK 0x3 677 #define ABORT_SINGLE 0x0 678 #define ABORT_ALL 0x1 679 680 /** 681 * brief the data structure of SSP SATA SMP Abort Response 682 * use to describe SSP SMP & SATA Abort Response ( 64 bytes) 683 */ 684 struct task_abort_resp { 685 __le32 tag; 686 __le32 status; 687 __le32 scp; 688 u32 reserved[12]; 689 } __attribute__((packed, aligned(4))); 690 691 /** 692 * brief the data structure of SAS Diagnostic Start/End Command 693 * use to describe MPI SAS Diagnostic Start/End Command (64 bytes) 694 */ 695 struct sas_diag_start_end_req { 696 __le32 tag; 697 __le32 operation_phyid; 698 u32 reserved[29]; 699 } __attribute__((packed, aligned(4))); 700 701 /** 702 * brief the data structure of SAS Diagnostic Execute Command 703 * use to describe MPI SAS Diagnostic Execute Command (64 bytes) 704 */ 705 struct sas_diag_execute_req { 706 __le32 tag; 707 __le32 cmdtype_cmddesc_phyid; 708 __le32 pat1_pat2; 709 __le32 threshold; 710 __le32 codepat_errmsk; 711 __le32 pmon; 712 __le32 pERF1CTL; 713 u32 reserved[24]; 714 } __attribute__((packed, aligned(4))); 715 716 #define SAS_DIAG_PARAM_BYTES 24 717 718 /* 719 * brief the data structure of Set Device State Command 720 * use to describe MPI Set Device State Command (64 bytes) 721 */ 722 struct set_dev_state_req { 723 __le32 tag; 724 __le32 device_id; 725 __le32 nds; 726 u32 reserved[28]; 727 } __attribute__((packed, aligned(4))); 728 729 /* 730 * brief the data structure of SATA Start Command 731 * use to describe MPI SATA IO Start Command (64 bytes) 732 * Note: This structure is common for normal / encryption I/O 733 */ 734 735 struct sata_start_req { 736 __le32 tag; 737 __le32 device_id; 738 __le32 data_len; 739 __le32 ncqtag_atap_dir_m_dad; 740 struct host_to_dev_fis sata_fis; 741 u32 reserved1; 742 u32 reserved2; /* dword 11. rsvd for normal I/O. */ 743 /* EPLE Descl for enc I/O */ 744 u32 addr_low; /* dword 12. rsvd for enc I/O */ 745 u32 addr_high; /* dword 13. reserved for enc I/O */ 746 __le32 len; /* dword 14: length for normal I/O. */ 747 /* EPLE Desch for enc I/O */ 748 __le32 esgl; /* dword 15. rsvd for enc I/O */ 749 __le32 atapi_scsi_cdb[4]; /* dword 16-19. rsvd for enc I/O */ 750 /* The below fields are reserved for normal I/O */ 751 __le32 key_index_mode; /* dword 20 */ 752 __le32 sector_cnt_enss;/* dword 21 */ 753 __le32 keytagl; /* dword 22 */ 754 __le32 keytagh; /* dword 23 */ 755 __le32 twk_val0; /* dword 24 */ 756 __le32 twk_val1; /* dword 25 */ 757 __le32 twk_val2; /* dword 26 */ 758 __le32 twk_val3; /* dword 27 */ 759 __le32 enc_addr_low; /* dword 28. Encryption SGL address high */ 760 __le32 enc_addr_high; /* dword 29. Encryption SGL address low */ 761 __le32 enc_len; /* dword 30. Encryption length */ 762 __le32 enc_esgl; /* dword 31. Encryption esgl bit */ 763 } __attribute__((packed, aligned(4))); 764 765 /** 766 * brief the data structure of SSP INI TM Start Command 767 * use to describe MPI SSP INI TM Start Command (64 bytes) 768 */ 769 struct ssp_ini_tm_start_req { 770 __le32 tag; 771 __le32 device_id; 772 __le32 relate_tag; 773 __le32 tmf; 774 u8 lun[8]; 775 __le32 ds_ads_m; 776 u32 reserved[24]; 777 } __attribute__((packed, aligned(4))); 778 779 struct ssp_info_unit { 780 u8 lun[8];/* SCSI Logical Unit Number */ 781 u8 reserved1;/* reserved */ 782 u8 efb_prio_attr; 783 /* B7 : enabledFirstBurst */ 784 /* B6-3 : taskPriority */ 785 /* B2-0 : taskAttribute */ 786 u8 reserved2; /* reserved */ 787 u8 additional_cdb_len; 788 /* B7-2 : additional_cdb_len */ 789 /* B1-0 : reserved */ 790 u8 cdb[16];/* The SCSI CDB up to 16 bytes length */ 791 } __attribute__((packed, aligned(4))); 792 793 /** 794 * brief the data structure of SSP INI IO Start Command 795 * use to describe MPI SSP INI IO Start Command (64 bytes) 796 * Note: This structure is common for normal / encryption I/O 797 */ 798 struct ssp_ini_io_start_req { 799 __le32 tag; 800 __le32 device_id; 801 __le32 data_len; 802 __le32 dad_dir_m_tlr; 803 struct ssp_info_unit ssp_iu; 804 __le32 addr_low; /* dword 12: sgl low for normal I/O. */ 805 /* epl_descl for encryption I/O */ 806 __le32 addr_high; /* dword 13: sgl hi for normal I/O */ 807 /* dpl_descl for encryption I/O */ 808 __le32 len; /* dword 14: len for normal I/O. */ 809 /* edpl_desch for encryption I/O */ 810 __le32 esgl; /* dword 15: ESGL bit for normal I/O. */ 811 /* user defined tag mask for enc I/O */ 812 /* The below fields are reserved for normal I/O */ 813 u8 udt[12]; /* dword 16-18 */ 814 __le32 sectcnt_ios; /* dword 19 */ 815 __le32 key_cmode; /* dword 20 */ 816 __le32 ks_enss; /* dword 21 */ 817 __le32 keytagl; /* dword 22 */ 818 __le32 keytagh; /* dword 23 */ 819 __le32 twk_val0; /* dword 24 */ 820 __le32 twk_val1; /* dword 25 */ 821 __le32 twk_val2; /* dword 26 */ 822 __le32 twk_val3; /* dword 27 */ 823 __le32 enc_addr_low; /* dword 28: Encryption sgl addr low */ 824 __le32 enc_addr_high; /* dword 29: Encryption sgl addr hi */ 825 __le32 enc_len; /* dword 30: Encryption length */ 826 __le32 enc_esgl; /* dword 31: ESGL bit for encryption */ 827 } __attribute__((packed, aligned(4))); 828 829 /** 830 * brief the data structure for SSP_INI_DIF_ENC_IO COMMAND 831 * use to initiate SSP I/O operation with optional DIF/ENC 832 */ 833 struct ssp_dif_enc_io_req { 834 __le32 tag; 835 __le32 device_id; 836 __le32 data_len; 837 __le32 dirMTlr; 838 __le32 sspiu0; 839 __le32 sspiu1; 840 __le32 sspiu2; 841 __le32 sspiu3; 842 __le32 sspiu4; 843 __le32 sspiu5; 844 __le32 sspiu6; 845 __le32 epl_des; 846 __le32 dpl_desl_ndplr; 847 __le32 dpl_desh; 848 __le32 uum_uuv_bss_difbits; 849 u8 udt[12]; 850 __le32 sectcnt_ios; 851 __le32 key_cmode; 852 __le32 ks_enss; 853 __le32 keytagl; 854 __le32 keytagh; 855 __le32 twk_val0; 856 __le32 twk_val1; 857 __le32 twk_val2; 858 __le32 twk_val3; 859 __le32 addr_low; 860 __le32 addr_high; 861 __le32 len; 862 __le32 esgl; 863 } __attribute__((packed, aligned(4))); 864 865 /** 866 * brief the data structure of Firmware download 867 * use to describe MPI FW DOWNLOAD Command (64 bytes) 868 */ 869 struct fw_flash_Update_req { 870 __le32 tag; 871 __le32 cur_image_offset; 872 __le32 cur_image_len; 873 __le32 total_image_len; 874 u32 reserved0[7]; 875 __le32 sgl_addr_lo; 876 __le32 sgl_addr_hi; 877 __le32 len; 878 __le32 ext_reserved; 879 u32 reserved1[16]; 880 } __attribute__((packed, aligned(4))); 881 882 #define FWFLASH_IOMB_RESERVED_LEN 0x07 883 /** 884 * brief the data structure of FW_FLASH_UPDATE Response 885 * use to describe MPI FW_FLASH_UPDATE Response (64 bytes) 886 * 887 */ 888 struct fw_flash_Update_resp { 889 __le32 tag; 890 __le32 status; 891 u32 reserved[13]; 892 } __attribute__((packed, aligned(4))); 893 894 /** 895 * brief the data structure of Get NVM Data Command 896 * use to get data from NVM in HBA(64 bytes) 897 */ 898 struct get_nvm_data_req { 899 __le32 tag; 900 __le32 len_ir_vpdd; 901 __le32 vpd_offset; 902 u32 reserved[8]; 903 __le32 resp_addr_lo; 904 __le32 resp_addr_hi; 905 __le32 resp_len; 906 u32 reserved1[17]; 907 } __attribute__((packed, aligned(4))); 908 909 struct set_nvm_data_req { 910 __le32 tag; 911 __le32 len_ir_vpdd; 912 __le32 vpd_offset; 913 u32 reserved[8]; 914 __le32 resp_addr_lo; 915 __le32 resp_addr_hi; 916 __le32 resp_len; 917 u32 reserved1[17]; 918 } __attribute__((packed, aligned(4))); 919 920 /** 921 * brief the data structure for SET CONTROLLER CONFIG COMMAND 922 * use to modify controller configuration 923 */ 924 struct set_ctrl_cfg_req { 925 __le32 tag; 926 __le32 cfg_pg[14]; 927 u32 reserved[16]; 928 } __attribute__((packed, aligned(4))); 929 930 /** 931 * brief the data structure for GET CONTROLLER CONFIG COMMAND 932 * use to get controller configuration page 933 */ 934 struct get_ctrl_cfg_req { 935 __le32 tag; 936 __le32 pgcd; 937 __le32 int_vec; 938 u32 reserved[28]; 939 } __attribute__((packed, aligned(4))); 940 941 /** 942 * brief the data structure for KEK_MANAGEMENT COMMAND 943 * use for KEK management 944 */ 945 struct kek_mgmt_req { 946 __le32 tag; 947 __le32 new_curidx_ksop; 948 u32 reserved; 949 __le32 kblob[12]; 950 u32 reserved1[16]; 951 } __attribute__((packed, aligned(4))); 952 953 /** 954 * brief the data structure for DEK_MANAGEMENT COMMAND 955 * use for DEK management 956 */ 957 struct dek_mgmt_req { 958 __le32 tag; 959 __le32 kidx_dsop; 960 __le32 dekidx; 961 __le32 addr_l; 962 __le32 addr_h; 963 __le32 nent; 964 __le32 dbf_tblsize; 965 u32 reserved[24]; 966 } __attribute__((packed, aligned(4))); 967 968 /** 969 * brief the data structure for SET PHY PROFILE COMMAND 970 * use to retrive phy specific information 971 */ 972 struct set_phy_profile_req { 973 __le32 tag; 974 __le32 ppc_phyid; 975 u32 reserved[29]; 976 } __attribute__((packed, aligned(4))); 977 978 /** 979 * brief the data structure for GET PHY PROFILE COMMAND 980 * use to retrive phy specific information 981 */ 982 struct get_phy_profile_req { 983 __le32 tag; 984 __le32 ppc_phyid; 985 __le32 profile[29]; 986 } __attribute__((packed, aligned(4))); 987 988 /** 989 * brief the data structure for EXT FLASH PARTITION 990 * use to manage ext flash partition 991 */ 992 struct ext_flash_partition_req { 993 __le32 tag; 994 __le32 cmd; 995 __le32 offset; 996 __le32 len; 997 u32 reserved[7]; 998 __le32 addr_low; 999 __le32 addr_high; 1000 __le32 len1; 1001 __le32 ext; 1002 u32 reserved1[16]; 1003 } __attribute__((packed, aligned(4))); 1004 1005 #define TWI_DEVICE 0x0 1006 #define C_SEEPROM 0x1 1007 #define VPD_FLASH 0x4 1008 #define AAP1_RDUMP 0x5 1009 #define IOP_RDUMP 0x6 1010 #define EXPAN_ROM 0x7 1011 1012 #define IPMode 0x80000000 1013 #define NVMD_TYPE 0x0000000F 1014 #define NVMD_STAT 0x0000FFFF 1015 #define NVMD_LEN 0xFF000000 1016 /** 1017 * brief the data structure of Get NVMD Data Response 1018 * use to describe MPI Get NVMD Data Response (64 bytes) 1019 */ 1020 struct get_nvm_data_resp { 1021 __le32 tag; 1022 __le32 ir_tda_bn_dps_das_nvm; 1023 __le32 dlen_status; 1024 __le32 nvm_data[12]; 1025 } __attribute__((packed, aligned(4))); 1026 1027 /** 1028 * brief the data structure of SAS Diagnostic Start/End Response 1029 * use to describe MPI SAS Diagnostic Start/End Response (64 bytes) 1030 * 1031 */ 1032 struct sas_diag_start_end_resp { 1033 __le32 tag; 1034 __le32 status; 1035 u32 reserved[13]; 1036 } __attribute__((packed, aligned(4))); 1037 1038 /** 1039 * brief the data structure of SAS Diagnostic Execute Response 1040 * use to describe MPI SAS Diagnostic Execute Response (64 bytes) 1041 * 1042 */ 1043 struct sas_diag_execute_resp { 1044 __le32 tag; 1045 __le32 cmdtype_cmddesc_phyid; 1046 __le32 Status; 1047 __le32 ReportData; 1048 u32 reserved[11]; 1049 } __attribute__((packed, aligned(4))); 1050 1051 /** 1052 * brief the data structure of Set Device State Response 1053 * use to describe MPI Set Device State Response (64 bytes) 1054 * 1055 */ 1056 struct set_dev_state_resp { 1057 __le32 tag; 1058 __le32 status; 1059 __le32 device_id; 1060 __le32 pds_nds; 1061 u32 reserved[11]; 1062 } __attribute__((packed, aligned(4))); 1063 1064 /* new outbound structure for spcv - begins */ 1065 /** 1066 * brief the data structure for SET CONTROLLER CONFIG COMMAND 1067 * use to modify controller configuration 1068 */ 1069 struct set_ctrl_cfg_resp { 1070 __le32 tag; 1071 __le32 status; 1072 __le32 err_qlfr_pgcd; 1073 u32 reserved[12]; 1074 } __attribute__((packed, aligned(4))); 1075 1076 struct get_ctrl_cfg_resp { 1077 __le32 tag; 1078 __le32 status; 1079 __le32 err_qlfr; 1080 __le32 confg_page[12]; 1081 } __attribute__((packed, aligned(4))); 1082 1083 struct kek_mgmt_resp { 1084 __le32 tag; 1085 __le32 status; 1086 __le32 kidx_new_curr_ksop; 1087 __le32 err_qlfr; 1088 u32 reserved[11]; 1089 } __attribute__((packed, aligned(4))); 1090 1091 struct dek_mgmt_resp { 1092 __le32 tag; 1093 __le32 status; 1094 __le32 kekidx_tbls_dsop; 1095 __le32 dekidx; 1096 __le32 err_qlfr; 1097 u32 reserved[10]; 1098 } __attribute__((packed, aligned(4))); 1099 1100 struct get_phy_profile_resp { 1101 __le32 tag; 1102 __le32 status; 1103 __le32 ppc_phyid; 1104 __le32 ppc_specific_rsp[12]; 1105 } __attribute__((packed, aligned(4))); 1106 1107 struct flash_op_ext_resp { 1108 __le32 tag; 1109 __le32 cmd; 1110 __le32 status; 1111 __le32 epart_size; 1112 __le32 epart_sect_size; 1113 u32 reserved[10]; 1114 } __attribute__((packed, aligned(4))); 1115 1116 struct set_phy_profile_resp { 1117 __le32 tag; 1118 __le32 status; 1119 __le32 ppc_phyid; 1120 __le32 ppc_specific_rsp[12]; 1121 } __attribute__((packed, aligned(4))); 1122 1123 struct ssp_coalesced_comp_resp { 1124 __le32 coal_cnt; 1125 __le32 tag0; 1126 __le32 ssp_tag0; 1127 __le32 tag1; 1128 __le32 ssp_tag1; 1129 __le32 add_tag_ssp_tag[10]; 1130 } __attribute__((packed, aligned(4))); 1131 1132 /* new outbound structure for spcv - ends */ 1133 1134 /* brief data structure for SAS protocol timer configuration page. 1135 * 1136 */ 1137 struct SASProtocolTimerConfig { 1138 __le32 pageCode; /* 0 */ 1139 __le32 MST_MSI; /* 1 */ 1140 __le32 STP_SSP_MCT_TMO; /* 2 */ 1141 __le32 STP_FRM_TMO; /* 3 */ 1142 __le32 STP_IDLE_TMO; /* 4 */ 1143 __le32 OPNRJT_RTRY_INTVL; /* 5 */ 1144 __le32 Data_Cmd_OPNRJT_RTRY_TMO; /* 6 */ 1145 __le32 Data_Cmd_OPNRJT_RTRY_THR; /* 7 */ 1146 __le32 MAX_AIP; /* 8 */ 1147 } __attribute__((packed, aligned(4))); 1148 1149 typedef struct SASProtocolTimerConfig SASProtocolTimerConfig_t; 1150 1151 #define NDS_BITS 0x0F 1152 #define PDS_BITS 0xF0 1153 1154 /* 1155 * HW Events type 1156 */ 1157 1158 #define HW_EVENT_RESET_START 0x01 1159 #define HW_EVENT_CHIP_RESET_COMPLETE 0x02 1160 #define HW_EVENT_PHY_STOP_STATUS 0x03 1161 #define HW_EVENT_SAS_PHY_UP 0x04 1162 #define HW_EVENT_SATA_PHY_UP 0x05 1163 #define HW_EVENT_SATA_SPINUP_HOLD 0x06 1164 #define HW_EVENT_PHY_DOWN 0x07 1165 #define HW_EVENT_PORT_INVALID 0x08 1166 #define HW_EVENT_BROADCAST_CHANGE 0x09 1167 #define HW_EVENT_PHY_ERROR 0x0A 1168 #define HW_EVENT_BROADCAST_SES 0x0B 1169 #define HW_EVENT_INBOUND_CRC_ERROR 0x0C 1170 #define HW_EVENT_HARD_RESET_RECEIVED 0x0D 1171 #define HW_EVENT_MALFUNCTION 0x0E 1172 #define HW_EVENT_ID_FRAME_TIMEOUT 0x0F 1173 #define HW_EVENT_BROADCAST_EXP 0x10 1174 #define HW_EVENT_PHY_START_STATUS 0x11 1175 #define HW_EVENT_LINK_ERR_INVALID_DWORD 0x12 1176 #define HW_EVENT_LINK_ERR_DISPARITY_ERROR 0x13 1177 #define HW_EVENT_LINK_ERR_CODE_VIOLATION 0x14 1178 #define HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH 0x15 1179 #define HW_EVENT_LINK_ERR_PHY_RESET_FAILED 0x16 1180 #define HW_EVENT_PORT_RECOVERY_TIMER_TMO 0x17 1181 #define HW_EVENT_PORT_RECOVER 0x18 1182 #define HW_EVENT_PORT_RESET_TIMER_TMO 0x19 1183 #define HW_EVENT_PORT_RESET_COMPLETE 0x20 1184 #define EVENT_BROADCAST_ASYNCH_EVENT 0x21 1185 1186 /* port state */ 1187 #define PORT_NOT_ESTABLISHED 0x00 1188 #define PORT_VALID 0x01 1189 #define PORT_LOSTCOMM 0x02 1190 #define PORT_IN_RESET 0x04 1191 #define PORT_3RD_PARTY_RESET 0x07 1192 #define PORT_INVALID 0x08 1193 1194 /* 1195 * SSP/SMP/SATA IO Completion Status values 1196 */ 1197 1198 #define IO_SUCCESS 0x00 1199 #define IO_ABORTED 0x01 1200 #define IO_OVERFLOW 0x02 1201 #define IO_UNDERFLOW 0x03 1202 #define IO_FAILED 0x04 1203 #define IO_ABORT_RESET 0x05 1204 #define IO_NOT_VALID 0x06 1205 #define IO_NO_DEVICE 0x07 1206 #define IO_ILLEGAL_PARAMETER 0x08 1207 #define IO_LINK_FAILURE 0x09 1208 #define IO_PROG_ERROR 0x0A 1209 1210 #define IO_EDC_IN_ERROR 0x0B 1211 #define IO_EDC_OUT_ERROR 0x0C 1212 #define IO_ERROR_HW_TIMEOUT 0x0D 1213 #define IO_XFER_ERROR_BREAK 0x0E 1214 #define IO_XFER_ERROR_PHY_NOT_READY 0x0F 1215 #define IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED 0x10 1216 #define IO_OPEN_CNX_ERROR_ZONE_VIOLATION 0x11 1217 #define IO_OPEN_CNX_ERROR_BREAK 0x12 1218 #define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS 0x13 1219 #define IO_OPEN_CNX_ERROR_BAD_DESTINATION 0x14 1220 #define IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED 0x15 1221 #define IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY 0x16 1222 #define IO_OPEN_CNX_ERROR_WRONG_DESTINATION 0x17 1223 /* This error code 0x18 is not used on SPCv */ 1224 #define IO_OPEN_CNX_ERROR_UNKNOWN_ERROR 0x18 1225 #define IO_XFER_ERROR_NAK_RECEIVED 0x19 1226 #define IO_XFER_ERROR_ACK_NAK_TIMEOUT 0x1A 1227 #define IO_XFER_ERROR_PEER_ABORTED 0x1B 1228 #define IO_XFER_ERROR_RX_FRAME 0x1C 1229 #define IO_XFER_ERROR_DMA 0x1D 1230 #define IO_XFER_ERROR_CREDIT_TIMEOUT 0x1E 1231 #define IO_XFER_ERROR_SATA_LINK_TIMEOUT 0x1F 1232 #define IO_XFER_ERROR_SATA 0x20 1233 1234 /* This error code 0x22 is not used on SPCv */ 1235 #define IO_XFER_ERROR_ABORTED_DUE_TO_SRST 0x22 1236 #define IO_XFER_ERROR_REJECTED_NCQ_MODE 0x21 1237 #define IO_XFER_ERROR_ABORTED_NCQ_MODE 0x23 1238 #define IO_XFER_OPEN_RETRY_TIMEOUT 0x24 1239 /* This error code 0x25 is not used on SPCv */ 1240 #define IO_XFER_SMP_RESP_CONNECTION_ERROR 0x25 1241 #define IO_XFER_ERROR_UNEXPECTED_PHASE 0x26 1242 #define IO_XFER_ERROR_XFER_RDY_OVERRUN 0x27 1243 #define IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED 0x28 1244 #define IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT 0x30 1245 1246 /* The following error code 0x31 and 0x32 are not using (obsolete) */ 1247 #define IO_XFER_ERROR_CMD_ISSUE_BREAK_BEFORE_ACK_NAK 0x31 1248 #define IO_XFER_ERROR_CMD_ISSUE_PHY_DOWN_BEFORE_ACK_NAK 0x32 1249 1250 #define IO_XFER_ERROR_OFFSET_MISMATCH 0x34 1251 #define IO_XFER_ERROR_XFER_ZERO_DATA_LEN 0x35 1252 #define IO_XFER_CMD_FRAME_ISSUED 0x36 1253 #define IO_ERROR_INTERNAL_SMP_RESOURCE 0x37 1254 #define IO_PORT_IN_RESET 0x38 1255 #define IO_DS_NON_OPERATIONAL 0x39 1256 #define IO_DS_IN_RECOVERY 0x3A 1257 #define IO_TM_TAG_NOT_FOUND 0x3B 1258 #define IO_XFER_PIO_SETUP_ERROR 0x3C 1259 #define IO_SSP_EXT_IU_ZERO_LEN_ERROR 0x3D 1260 #define IO_DS_IN_ERROR 0x3E 1261 #define IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY 0x3F 1262 #define IO_ABORT_IN_PROGRESS 0x40 1263 #define IO_ABORT_DELAYED 0x41 1264 #define IO_INVALID_LENGTH 0x42 1265 1266 /********** additional response event values *****************/ 1267 1268 #define IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY_ALT 0x43 1269 #define IO_XFER_OPEN_RETRY_BACKOFF_THRESHOLD_REACHED 0x44 1270 #define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_TMO 0x45 1271 #define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_NO_DEST 0x46 1272 #define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_OPEN_COLLIDE 0x47 1273 #define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS_PATHWAY_BLOCKED 0x48 1274 #define IO_DS_INVALID 0x49 1275 /* WARNING: the value is not contiguous from here */ 1276 #define IO_XFER_ERR_LAST_PIO_DATAIN_CRC_ERR 0x52 1277 #define IO_XFER_DMA_ACTIVATE_TIMEOUT 0x53 1278 #define IO_XFER_ERROR_INTERNAL_CRC_ERROR 0x54 1279 #define MPI_IO_RQE_BUSY_FULL 0x55 1280 #define IO_XFER_ERR_EOB_DATA_OVERRUN 0x56 1281 #define IO_XFER_ERROR_INVALID_SSP_RSP_FRAME 0x57 1282 #define IO_OPEN_CNX_ERROR_OPEN_PREEMPTED 0x58 1283 1284 #define MPI_ERR_IO_RESOURCE_UNAVAILABLE 0x1004 1285 #define MPI_ERR_ATAPI_DEVICE_BUSY 0x1024 1286 1287 #define IO_XFR_ERROR_DEK_KEY_CACHE_MISS 0x2040 1288 /* 1289 * An encryption IO request failed due to DEK Key Tag mismatch. 1290 * The key tag supplied in the encryption IOMB does not match with 1291 * the Key Tag in the referenced DEK Entry. 1292 */ 1293 #define IO_XFR_ERROR_DEK_KEY_TAG_MISMATCH 0x2041 1294 #define IO_XFR_ERROR_CIPHER_MODE_INVALID 0x2042 1295 /* 1296 * An encryption I/O request failed because the initial value (IV) 1297 * in the unwrapped DEK blob didn't match the IV used to unwrap it. 1298 */ 1299 #define IO_XFR_ERROR_DEK_IV_MISMATCH 0x2043 1300 /* An encryption I/O request failed due to an internal RAM ECC or 1301 * interface error while unwrapping the DEK. */ 1302 #define IO_XFR_ERROR_DEK_RAM_INTERFACE_ERROR 0x2044 1303 /* An encryption I/O request failed due to an internal RAM ECC or 1304 * interface error while unwrapping the DEK. */ 1305 #define IO_XFR_ERROR_INTERNAL_RAM 0x2045 1306 /* 1307 * An encryption I/O request failed 1308 * because the DEK index specified in the I/O was outside the bounds of 1309 * the total number of entries in the host DEK table. 1310 */ 1311 #define IO_XFR_ERROR_DEK_INDEX_OUT_OF_BOUNDS0x2046 1312 1313 /* define DIF IO response error status code */ 1314 #define IO_XFR_ERROR_DIF_MISMATCH 0x3000 1315 #define IO_XFR_ERROR_DIF_APPLICATION_TAG_MISMATCH 0x3001 1316 #define IO_XFR_ERROR_DIF_REFERENCE_TAG_MISMATCH 0x3002 1317 #define IO_XFR_ERROR_DIF_CRC_MISMATCH 0x3003 1318 1319 /* define operator management response status and error qualifier code */ 1320 #define OPR_MGMT_OP_NOT_SUPPORTED 0x2060 1321 #define OPR_MGMT_MPI_ENC_ERR_OPR_PARAM_ILLEGAL 0x2061 1322 #define OPR_MGMT_MPI_ENC_ERR_OPR_ID_NOT_FOUND 0x2062 1323 #define OPR_MGMT_MPI_ENC_ERR_OPR_ROLE_NOT_MATCH 0x2063 1324 #define OPR_MGMT_MPI_ENC_ERR_OPR_MAX_NUM_EXCEEDED 0x2064 1325 #define OPR_MGMT_MPI_ENC_ERR_KEK_UNWRAP_FAIL 0x2022 1326 #define OPR_MGMT_MPI_ENC_ERR_NVRAM_OPERATION_FAILURE 0x2023 1327 /***************** additional response event values ***************/ 1328 1329 /* WARNING: This error code must always be the last number. 1330 * If you add error code, modify this code also 1331 * It is used as an index 1332 */ 1333 #define IO_ERROR_UNKNOWN_GENERIC 0x2023 1334 1335 /* MSGU CONFIGURATION TABLE*/ 1336 1337 #define SPCv_MSGU_CFG_TABLE_UPDATE 0x001 1338 #define SPCv_MSGU_CFG_TABLE_RESET 0x002 1339 #define SPCv_MSGU_CFG_TABLE_FREEZE 0x004 1340 #define SPCv_MSGU_CFG_TABLE_UNFREEZE 0x008 1341 #define MSGU_IBDB_SET 0x00 1342 #define MSGU_HOST_INT_STATUS 0x08 1343 #define MSGU_HOST_INT_MASK 0x0C 1344 #define MSGU_IOPIB_INT_STATUS 0x18 1345 #define MSGU_IOPIB_INT_MASK 0x1C 1346 #define MSGU_IBDB_CLEAR 0x20 1347 1348 #define MSGU_MSGU_CONTROL 0x24 1349 #define MSGU_ODR 0x20 1350 #define MSGU_ODCR 0x28 1351 1352 #define MSGU_ODMR 0x30 1353 #define MSGU_ODMR_U 0x34 1354 #define MSGU_ODMR_CLR 0x38 1355 #define MSGU_ODMR_CLR_U 0x3C 1356 #define MSGU_OD_RSVD 0x40 1357 1358 #define MSGU_SCRATCH_PAD_0 0x44 1359 #define MSGU_SCRATCH_PAD_1 0x48 1360 #define MSGU_SCRATCH_PAD_2 0x4C 1361 #define MSGU_SCRATCH_PAD_3 0x50 1362 #define MSGU_HOST_SCRATCH_PAD_0 0x54 1363 #define MSGU_HOST_SCRATCH_PAD_1 0x58 1364 #define MSGU_HOST_SCRATCH_PAD_2 0x5C 1365 #define MSGU_HOST_SCRATCH_PAD_3 0x60 1366 #define MSGU_HOST_SCRATCH_PAD_4 0x64 1367 #define MSGU_HOST_SCRATCH_PAD_5 0x68 1368 #define MSGU_HOST_SCRATCH_PAD_6 0x6C 1369 #define MSGU_HOST_SCRATCH_PAD_7 0x70 1370 1371 #define MSGU_SCRATCHPAD1_RAAE_STATE_ERR(x) ((x & 0x3) == 0x2) 1372 #define MSGU_SCRATCHPAD1_ILA_STATE_ERR(x) (((x >> 2) & 0x3) == 0x2) 1373 #define MSGU_SCRATCHPAD1_BOOTLDR_STATE_ERR(x) ((((x >> 4) & 0x7) == 0x7) || \ 1374 (((x >> 4) & 0x7) == 0x4)) 1375 #define MSGU_SCRATCHPAD1_IOP0_STATE_ERR(x) (((x >> 10) & 0x3) == 0x2) 1376 #define MSGU_SCRATCHPAD1_IOP1_STATE_ERR(x) (((x >> 12) & 0x3) == 0x2) 1377 #define MSGU_SCRATCHPAD1_STATE_FATAL_ERROR(x) \ 1378 (MSGU_SCRATCHPAD1_RAAE_STATE_ERR(x) || \ 1379 MSGU_SCRATCHPAD1_ILA_STATE_ERR(x) || \ 1380 MSGU_SCRATCHPAD1_BOOTLDR_STATE_ERR(x) || \ 1381 MSGU_SCRATCHPAD1_IOP0_STATE_ERR(x) || \ 1382 MSGU_SCRATCHPAD1_IOP1_STATE_ERR(x)) 1383 1384 /* bit definition for ODMR register */ 1385 #define ODMR_MASK_ALL 0xFFFFFFFF/* mask all 1386 interrupt vector */ 1387 #define ODMR_CLEAR_ALL 0 /* clear all 1388 interrupt vector */ 1389 /* bit definition for ODCR register */ 1390 #define ODCR_CLEAR_ALL 0xFFFFFFFF /* mask all 1391 interrupt vector*/ 1392 /* MSIX Interupts */ 1393 #define MSIX_TABLE_OFFSET 0x2000 1394 #define MSIX_TABLE_ELEMENT_SIZE 0x10 1395 #define MSIX_INTERRUPT_CONTROL_OFFSET 0xC 1396 #define MSIX_TABLE_BASE (MSIX_TABLE_OFFSET + \ 1397 MSIX_INTERRUPT_CONTROL_OFFSET) 1398 #define MSIX_INTERRUPT_DISABLE 0x1 1399 #define MSIX_INTERRUPT_ENABLE 0x0 1400 1401 /* state definition for Scratch Pad1 register */ 1402 #define SCRATCH_PAD_RAAE_READY 0x3 1403 #define SCRATCH_PAD_ILA_READY 0xC 1404 #define SCRATCH_PAD_BOOT_LOAD_SUCCESS 0x0 1405 #define SCRATCH_PAD_IOP0_READY 0xC00 1406 #define SCRATCH_PAD_IOP1_READY 0x3000 1407 #define SCRATCH_PAD_MIPSALL_READY (SCRATCH_PAD_IOP1_READY | \ 1408 SCRATCH_PAD_IOP0_READY | \ 1409 SCRATCH_PAD_RAAE_READY) 1410 1411 /* boot loader state */ 1412 #define SCRATCH_PAD1_BOOTSTATE_MASK 0x70 /* Bit 4-6 */ 1413 #define SCRATCH_PAD1_BOOTSTATE_SUCESS 0x0 /* Load successful */ 1414 #define SCRATCH_PAD1_BOOTSTATE_HDA_SEEPROM 0x10 /* HDA SEEPROM */ 1415 #define SCRATCH_PAD1_BOOTSTATE_HDA_BOOTSTRAP 0x20 /* HDA BootStrap Pins */ 1416 #define SCRATCH_PAD1_BOOTSTATE_HDA_SOFTRESET 0x30 /* HDA Soft Reset */ 1417 #define SCRATCH_PAD1_BOOTSTATE_CRIT_ERROR 0x40 /* HDA critical error */ 1418 #define SCRATCH_PAD1_BOOTSTATE_R1 0x50 /* Reserved */ 1419 #define SCRATCH_PAD1_BOOTSTATE_R2 0x60 /* Reserved */ 1420 #define SCRATCH_PAD1_BOOTSTATE_FATAL 0x70 /* Fatal Error */ 1421 1422 /* state definition for Scratch Pad2 register */ 1423 #define SCRATCH_PAD2_POR 0x00 /* power on state */ 1424 #define SCRATCH_PAD2_SFR 0x01 /* soft reset state */ 1425 #define SCRATCH_PAD2_ERR 0x02 /* error state */ 1426 #define SCRATCH_PAD2_RDY 0x03 /* ready state */ 1427 #define SCRATCH_PAD2_FWRDY_RST 0x04 /* FW rdy for soft reset flag */ 1428 #define SCRATCH_PAD2_IOPRDY_RST 0x08 /* IOP ready for soft reset */ 1429 #define SCRATCH_PAD2_STATE_MASK 0xFFFFFFF4 /* ScratchPad 2 1430 Mask, bit1-0 State */ 1431 #define SCRATCH_PAD2_RESERVED 0x000003FC/* Scratch Pad1 1432 Reserved bit 2 to 9 */ 1433 1434 #define SCRATCH_PAD_ERROR_MASK 0xFFFFFC00 /* Error mask bits */ 1435 #define SCRATCH_PAD_STATE_MASK 0x00000003 /* State Mask bits */ 1436 1437 /* main configuration offset - byte offset */ 1438 #define MAIN_SIGNATURE_OFFSET 0x00 /* DWORD 0x00 */ 1439 #define MAIN_INTERFACE_REVISION 0x04 /* DWORD 0x01 */ 1440 #define MAIN_FW_REVISION 0x08 /* DWORD 0x02 */ 1441 #define MAIN_MAX_OUTSTANDING_IO_OFFSET 0x0C /* DWORD 0x03 */ 1442 #define MAIN_MAX_SGL_OFFSET 0x10 /* DWORD 0x04 */ 1443 #define MAIN_CNTRL_CAP_OFFSET 0x14 /* DWORD 0x05 */ 1444 #define MAIN_GST_OFFSET 0x18 /* DWORD 0x06 */ 1445 #define MAIN_IBQ_OFFSET 0x1C /* DWORD 0x07 */ 1446 #define MAIN_OBQ_OFFSET 0x20 /* DWORD 0x08 */ 1447 #define MAIN_IQNPPD_HPPD_OFFSET 0x24 /* DWORD 0x09 */ 1448 1449 /* 0x28 - 0x4C - RSVD */ 1450 #define MAIN_EVENT_CRC_CHECK 0x48 /* DWORD 0x12 */ 1451 #define MAIN_EVENT_LOG_ADDR_HI 0x50 /* DWORD 0x14 */ 1452 #define MAIN_EVENT_LOG_ADDR_LO 0x54 /* DWORD 0x15 */ 1453 #define MAIN_EVENT_LOG_BUFF_SIZE 0x58 /* DWORD 0x16 */ 1454 #define MAIN_EVENT_LOG_OPTION 0x5C /* DWORD 0x17 */ 1455 #define MAIN_PCS_EVENT_LOG_ADDR_HI 0x60 /* DWORD 0x18 */ 1456 #define MAIN_PCS_EVENT_LOG_ADDR_LO 0x64 /* DWORD 0x19 */ 1457 #define MAIN_PCS_EVENT_LOG_BUFF_SIZE 0x68 /* DWORD 0x1A */ 1458 #define MAIN_PCS_EVENT_LOG_OPTION 0x6C /* DWORD 0x1B */ 1459 #define MAIN_FATAL_ERROR_INTERRUPT 0x70 /* DWORD 0x1C */ 1460 #define MAIN_FATAL_ERROR_RDUMP0_OFFSET 0x74 /* DWORD 0x1D */ 1461 #define MAIN_FATAL_ERROR_RDUMP0_LENGTH 0x78 /* DWORD 0x1E */ 1462 #define MAIN_FATAL_ERROR_RDUMP1_OFFSET 0x7C /* DWORD 0x1F */ 1463 #define MAIN_FATAL_ERROR_RDUMP1_LENGTH 0x80 /* DWORD 0x20 */ 1464 #define MAIN_GPIO_LED_FLAGS_OFFSET 0x84 /* DWORD 0x21 */ 1465 #define MAIN_ANALOG_SETUP_OFFSET 0x88 /* DWORD 0x22 */ 1466 1467 #define MAIN_INT_VECTOR_TABLE_OFFSET 0x8C /* DWORD 0x23 */ 1468 #define MAIN_SAS_PHY_ATTR_TABLE_OFFSET 0x90 /* DWORD 0x24 */ 1469 #define MAIN_PORT_RECOVERY_TIMER 0x94 /* DWORD 0x25 */ 1470 #define MAIN_INT_REASSERTION_DELAY 0x98 /* DWORD 0x26 */ 1471 #define MAIN_MPI_ILA_RELEASE_TYPE 0xA4 /* DWORD 0x29 */ 1472 #define MAIN_MPI_INACTIVE_FW_VERSION 0XB0 /* DWORD 0x2C */ 1473 1474 /* Gereral Status Table offset - byte offset */ 1475 #define GST_GSTLEN_MPIS_OFFSET 0x00 1476 #define GST_IQ_FREEZE_STATE0_OFFSET 0x04 1477 #define GST_IQ_FREEZE_STATE1_OFFSET 0x08 1478 #define GST_MSGUTCNT_OFFSET 0x0C 1479 #define GST_IOPTCNT_OFFSET 0x10 1480 /* 0x14 - 0x34 - RSVD */ 1481 #define GST_GPIO_INPUT_VAL 0x38 1482 /* 0x3c - 0x40 - RSVD */ 1483 #define GST_RERRINFO_OFFSET0 0x44 1484 #define GST_RERRINFO_OFFSET1 0x48 1485 #define GST_RERRINFO_OFFSET2 0x4c 1486 #define GST_RERRINFO_OFFSET3 0x50 1487 #define GST_RERRINFO_OFFSET4 0x54 1488 #define GST_RERRINFO_OFFSET5 0x58 1489 #define GST_RERRINFO_OFFSET6 0x5c 1490 #define GST_RERRINFO_OFFSET7 0x60 1491 1492 /* General Status Table - MPI state */ 1493 #define GST_MPI_STATE_UNINIT 0x00 1494 #define GST_MPI_STATE_INIT 0x01 1495 #define GST_MPI_STATE_TERMINATION 0x02 1496 #define GST_MPI_STATE_ERROR 0x03 1497 #define GST_MPI_STATE_MASK 0x07 1498 1499 /* Per SAS PHY Attributes */ 1500 1501 #define PSPA_PHYSTATE0_OFFSET 0x00 /* Dword V */ 1502 #define PSPA_OB_HW_EVENT_PID0_OFFSET 0x04 /* DWORD V+1 */ 1503 #define PSPA_PHYSTATE1_OFFSET 0x08 /* Dword V+2 */ 1504 #define PSPA_OB_HW_EVENT_PID1_OFFSET 0x0C /* DWORD V+3 */ 1505 #define PSPA_PHYSTATE2_OFFSET 0x10 /* Dword V+4 */ 1506 #define PSPA_OB_HW_EVENT_PID2_OFFSET 0x14 /* DWORD V+5 */ 1507 #define PSPA_PHYSTATE3_OFFSET 0x18 /* Dword V+6 */ 1508 #define PSPA_OB_HW_EVENT_PID3_OFFSET 0x1C /* DWORD V+7 */ 1509 #define PSPA_PHYSTATE4_OFFSET 0x20 /* Dword V+8 */ 1510 #define PSPA_OB_HW_EVENT_PID4_OFFSET 0x24 /* DWORD V+9 */ 1511 #define PSPA_PHYSTATE5_OFFSET 0x28 /* Dword V+10 */ 1512 #define PSPA_OB_HW_EVENT_PID5_OFFSET 0x2C /* DWORD V+11 */ 1513 #define PSPA_PHYSTATE6_OFFSET 0x30 /* Dword V+12 */ 1514 #define PSPA_OB_HW_EVENT_PID6_OFFSET 0x34 /* DWORD V+13 */ 1515 #define PSPA_PHYSTATE7_OFFSET 0x38 /* Dword V+14 */ 1516 #define PSPA_OB_HW_EVENT_PID7_OFFSET 0x3C /* DWORD V+15 */ 1517 #define PSPA_PHYSTATE8_OFFSET 0x40 /* DWORD V+16 */ 1518 #define PSPA_OB_HW_EVENT_PID8_OFFSET 0x44 /* DWORD V+17 */ 1519 #define PSPA_PHYSTATE9_OFFSET 0x48 /* DWORD V+18 */ 1520 #define PSPA_OB_HW_EVENT_PID9_OFFSET 0x4C /* DWORD V+19 */ 1521 #define PSPA_PHYSTATE10_OFFSET 0x50 /* DWORD V+20 */ 1522 #define PSPA_OB_HW_EVENT_PID10_OFFSET 0x54 /* DWORD V+21 */ 1523 #define PSPA_PHYSTATE11_OFFSET 0x58 /* DWORD V+22 */ 1524 #define PSPA_OB_HW_EVENT_PID11_OFFSET 0x5C /* DWORD V+23 */ 1525 #define PSPA_PHYSTATE12_OFFSET 0x60 /* DWORD V+24 */ 1526 #define PSPA_OB_HW_EVENT_PID12_OFFSET 0x64 /* DWORD V+25 */ 1527 #define PSPA_PHYSTATE13_OFFSET 0x68 /* DWORD V+26 */ 1528 #define PSPA_OB_HW_EVENT_PID13_OFFSET 0x6c /* DWORD V+27 */ 1529 #define PSPA_PHYSTATE14_OFFSET 0x70 /* DWORD V+28 */ 1530 #define PSPA_OB_HW_EVENT_PID14_OFFSET 0x74 /* DWORD V+29 */ 1531 #define PSPA_PHYSTATE15_OFFSET 0x78 /* DWORD V+30 */ 1532 #define PSPA_OB_HW_EVENT_PID15_OFFSET 0x7c /* DWORD V+31 */ 1533 /* end PSPA */ 1534 1535 /* inbound queue configuration offset - byte offset */ 1536 #define IB_PROPERITY_OFFSET 0x00 1537 #define IB_BASE_ADDR_HI_OFFSET 0x04 1538 #define IB_BASE_ADDR_LO_OFFSET 0x08 1539 #define IB_CI_BASE_ADDR_HI_OFFSET 0x0C 1540 #define IB_CI_BASE_ADDR_LO_OFFSET 0x10 1541 #define IB_PIPCI_BAR 0x14 1542 #define IB_PIPCI_BAR_OFFSET 0x18 1543 #define IB_RESERVED_OFFSET 0x1C 1544 1545 /* outbound queue configuration offset - byte offset */ 1546 #define OB_PROPERITY_OFFSET 0x00 1547 #define OB_BASE_ADDR_HI_OFFSET 0x04 1548 #define OB_BASE_ADDR_LO_OFFSET 0x08 1549 #define OB_PI_BASE_ADDR_HI_OFFSET 0x0C 1550 #define OB_PI_BASE_ADDR_LO_OFFSET 0x10 1551 #define OB_CIPCI_BAR 0x14 1552 #define OB_CIPCI_BAR_OFFSET 0x18 1553 #define OB_INTERRUPT_COALES_OFFSET 0x1C 1554 #define OB_DYNAMIC_COALES_OFFSET 0x20 1555 #define OB_PROPERTY_INT_ENABLE 0x40000000 1556 1557 #define MBIC_NMI_ENABLE_VPE0_IOP 0x000418 1558 #define MBIC_NMI_ENABLE_VPE0_AAP1 0x000418 1559 /* PCIE registers - BAR2(0x18), BAR1(win) 0x010000 */ 1560 #define PCIE_EVENT_INTERRUPT_ENABLE 0x003040 1561 #define PCIE_EVENT_INTERRUPT 0x003044 1562 #define PCIE_ERROR_INTERRUPT_ENABLE 0x003048 1563 #define PCIE_ERROR_INTERRUPT 0x00304C 1564 1565 /* SPCV soft reset */ 1566 #define SPC_REG_SOFT_RESET 0x00001000 1567 #define SPCv_NORMAL_RESET_VALUE 0x1 1568 1569 #define SPCv_SOFT_RESET_READ_MASK 0xC0 1570 #define SPCv_SOFT_RESET_NO_RESET 0x0 1571 #define SPCv_SOFT_RESET_NORMAL_RESET_OCCURED 0x40 1572 #define SPCv_SOFT_RESET_HDA_MODE_OCCURED 0x80 1573 #define SPCv_SOFT_RESET_CHIP_RESET_OCCURED 0xC0 1574 1575 /* signature definition for host scratch pad0 register */ 1576 #define SPC_SOFT_RESET_SIGNATURE 0x252acbcd 1577 /* Signature for Soft Reset */ 1578 1579 /* SPC Reset register - BAR4(0x20), BAR2(win) (need dynamic mapping) */ 1580 #define SPC_REG_RESET 0x000000/* reset register */ 1581 1582 /* bit definition for SPC_RESET register */ 1583 #define SPC_REG_RESET_OSSP 0x00000001 1584 #define SPC_REG_RESET_RAAE 0x00000002 1585 #define SPC_REG_RESET_PCS_SPBC 0x00000004 1586 #define SPC_REG_RESET_PCS_IOP_SS 0x00000008 1587 #define SPC_REG_RESET_PCS_AAP1_SS 0x00000010 1588 #define SPC_REG_RESET_PCS_AAP2_SS 0x00000020 1589 #define SPC_REG_RESET_PCS_LM 0x00000040 1590 #define SPC_REG_RESET_PCS 0x00000080 1591 #define SPC_REG_RESET_GSM 0x00000100 1592 #define SPC_REG_RESET_DDR2 0x00010000 1593 #define SPC_REG_RESET_BDMA_CORE 0x00020000 1594 #define SPC_REG_RESET_BDMA_SXCBI 0x00040000 1595 #define SPC_REG_RESET_PCIE_AL_SXCBI 0x00080000 1596 #define SPC_REG_RESET_PCIE_PWR 0x00100000 1597 #define SPC_REG_RESET_PCIE_SFT 0x00200000 1598 #define SPC_REG_RESET_PCS_SXCBI 0x00400000 1599 #define SPC_REG_RESET_LMS_SXCBI 0x00800000 1600 #define SPC_REG_RESET_PMIC_SXCBI 0x01000000 1601 #define SPC_REG_RESET_PMIC_CORE 0x02000000 1602 #define SPC_REG_RESET_PCIE_PC_SXCBI 0x04000000 1603 #define SPC_REG_RESET_DEVICE 0x80000000 1604 1605 /* registers for BAR Shifting - BAR2(0x18), BAR1(win) */ 1606 #define SPCV_IBW_AXI_TRANSLATION_LOW 0x001010 1607 1608 #define MBIC_AAP1_ADDR_BASE 0x060000 1609 #define MBIC_IOP_ADDR_BASE 0x070000 1610 #define GSM_ADDR_BASE 0x0700000 1611 /* Dynamic map through Bar4 - 0x00700000 */ 1612 #define GSM_CONFIG_RESET 0x00000000 1613 #define RAM_ECC_DB_ERR 0x00000018 1614 #define GSM_READ_ADDR_PARITY_INDIC 0x00000058 1615 #define GSM_WRITE_ADDR_PARITY_INDIC 0x00000060 1616 #define GSM_WRITE_DATA_PARITY_INDIC 0x00000068 1617 #define GSM_READ_ADDR_PARITY_CHECK 0x00000038 1618 #define GSM_WRITE_ADDR_PARITY_CHECK 0x00000040 1619 #define GSM_WRITE_DATA_PARITY_CHECK 0x00000048 1620 1621 #define RB6_ACCESS_REG 0x6A0000 1622 #define HDAC_EXEC_CMD 0x0002 1623 #define HDA_C_PA 0xcb 1624 #define HDA_SEQ_ID_BITS 0x00ff0000 1625 #define HDA_GSM_OFFSET_BITS 0x00FFFFFF 1626 #define HDA_GSM_CMD_OFFSET_BITS 0x42C0 1627 #define HDA_GSM_RSP_OFFSET_BITS 0x42E0 1628 1629 #define MBIC_AAP1_ADDR_BASE 0x060000 1630 #define MBIC_IOP_ADDR_BASE 0x070000 1631 #define GSM_ADDR_BASE 0x0700000 1632 #define SPC_TOP_LEVEL_ADDR_BASE 0x000000 1633 #define GSM_CONFIG_RESET_VALUE 0x00003b00 1634 #define GPIO_ADDR_BASE 0x00090000 1635 #define GPIO_GPIO_0_0UTPUT_CTL_OFFSET 0x0000010c 1636 1637 /* RB6 offset */ 1638 #define SPC_RB6_OFFSET 0x80C0 1639 /* Magic number of soft reset for RB6 */ 1640 #define RB6_MAGIC_NUMBER_RST 0x1234 1641 1642 /* Device Register status */ 1643 #define DEVREG_SUCCESS 0x00 1644 #define DEVREG_FAILURE_OUT_OF_RESOURCE 0x01 1645 #define DEVREG_FAILURE_DEVICE_ALREADY_REGISTERED 0x02 1646 #define DEVREG_FAILURE_INVALID_PHY_ID 0x03 1647 #define DEVREG_FAILURE_PHY_ID_ALREADY_REGISTERED 0x04 1648 #define DEVREG_FAILURE_PORT_ID_OUT_OF_RANGE 0x05 1649 #define DEVREG_FAILURE_PORT_NOT_VALID_STATE 0x06 1650 #define DEVREG_FAILURE_DEVICE_TYPE_NOT_VALID 0x07 1651 1652 1653 #define MEMBASE_II_SHIFT_REGISTER 0x1010 1654 #endif 1655 1656 /** 1657 * As we know sleep (1~20) ms may result in sleep longer than ~20 ms, hence we 1658 * choose 20 ms interval. 1659 */ 1660 #define FW_READY_INTERVAL 20 1661