1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * NinjaSCSI-32Bi Cardbus, NinjaSCSI-32UDE PCI/CardBus SCSI driver 4 * Copyright (C) 2001, 2002, 2003 5 * YOKOTA Hiroshi <yokota@netlab.is.tsukuba.ac.jp> 6 * GOTO Masanori <gotom@debian.or.jp>, <gotom@debian.org> 7 * 8 * Revision History: 9 * 1.0: Initial Release. 10 * 1.1: Add /proc SDTR status. 11 * Remove obsolete error handler nsp32_reset. 12 * Some clean up. 13 * 1.2: PowerPC (big endian) support. 14 */ 15 16 #include <linux/module.h> 17 #include <linux/init.h> 18 #include <linux/kernel.h> 19 #include <linux/string.h> 20 #include <linux/timer.h> 21 #include <linux/ioport.h> 22 #include <linux/major.h> 23 #include <linux/blkdev.h> 24 #include <linux/interrupt.h> 25 #include <linux/pci.h> 26 #include <linux/delay.h> 27 #include <linux/ctype.h> 28 #include <linux/dma-mapping.h> 29 30 #include <asm/dma.h> 31 #include <asm/io.h> 32 33 #include <scsi/scsi.h> 34 #include <scsi/scsi_cmnd.h> 35 #include <scsi/scsi_device.h> 36 #include <scsi/scsi_host.h> 37 #include <scsi/scsi_ioctl.h> 38 39 #include "nsp32.h" 40 41 42 /*********************************************************************** 43 * Module parameters 44 */ 45 static int trans_mode = 0; /* default: BIOS */ 46 module_param (trans_mode, int, 0); 47 MODULE_PARM_DESC(trans_mode, "transfer mode (0: BIOS(default) 1: Async 2: Ultra20M"); 48 #define ASYNC_MODE 1 49 #define ULTRA20M_MODE 2 50 51 static bool auto_param = 0; /* default: ON */ 52 module_param (auto_param, bool, 0); 53 MODULE_PARM_DESC(auto_param, "AutoParameter mode (0: ON(default) 1: OFF)"); 54 55 static bool disc_priv = 1; /* default: OFF */ 56 module_param (disc_priv, bool, 0); 57 MODULE_PARM_DESC(disc_priv, "disconnection privilege mode (0: ON 1: OFF(default))"); 58 59 MODULE_AUTHOR("YOKOTA Hiroshi <yokota@netlab.is.tsukuba.ac.jp>, GOTO Masanori <gotom@debian.or.jp>"); 60 MODULE_DESCRIPTION("Workbit NinjaSCSI-32Bi/UDE CardBus/PCI SCSI host bus adapter module"); 61 MODULE_LICENSE("GPL"); 62 63 static const char *nsp32_release_version = "1.2"; 64 65 66 /**************************************************************************** 67 * Supported hardware 68 */ 69 static struct pci_device_id nsp32_pci_table[] = { 70 { 71 .vendor = PCI_VENDOR_ID_IODATA, 72 .device = PCI_DEVICE_ID_NINJASCSI_32BI_CBSC_II, 73 .subvendor = PCI_ANY_ID, 74 .subdevice = PCI_ANY_ID, 75 .driver_data = MODEL_IODATA, 76 }, 77 { 78 .vendor = PCI_VENDOR_ID_WORKBIT, 79 .device = PCI_DEVICE_ID_NINJASCSI_32BI_KME, 80 .subvendor = PCI_ANY_ID, 81 .subdevice = PCI_ANY_ID, 82 .driver_data = MODEL_KME, 83 }, 84 { 85 .vendor = PCI_VENDOR_ID_WORKBIT, 86 .device = PCI_DEVICE_ID_NINJASCSI_32BI_WBT, 87 .subvendor = PCI_ANY_ID, 88 .subdevice = PCI_ANY_ID, 89 .driver_data = MODEL_WORKBIT, 90 }, 91 { 92 .vendor = PCI_VENDOR_ID_WORKBIT, 93 .device = PCI_DEVICE_ID_WORKBIT_STANDARD, 94 .subvendor = PCI_ANY_ID, 95 .subdevice = PCI_ANY_ID, 96 .driver_data = MODEL_PCI_WORKBIT, 97 }, 98 { 99 .vendor = PCI_VENDOR_ID_WORKBIT, 100 .device = PCI_DEVICE_ID_NINJASCSI_32BI_LOGITEC, 101 .subvendor = PCI_ANY_ID, 102 .subdevice = PCI_ANY_ID, 103 .driver_data = MODEL_LOGITEC, 104 }, 105 { 106 .vendor = PCI_VENDOR_ID_WORKBIT, 107 .device = PCI_DEVICE_ID_NINJASCSI_32BIB_LOGITEC, 108 .subvendor = PCI_ANY_ID, 109 .subdevice = PCI_ANY_ID, 110 .driver_data = MODEL_PCI_LOGITEC, 111 }, 112 { 113 .vendor = PCI_VENDOR_ID_WORKBIT, 114 .device = PCI_DEVICE_ID_NINJASCSI_32UDE_MELCO, 115 .subvendor = PCI_ANY_ID, 116 .subdevice = PCI_ANY_ID, 117 .driver_data = MODEL_PCI_MELCO, 118 }, 119 { 120 .vendor = PCI_VENDOR_ID_WORKBIT, 121 .device = PCI_DEVICE_ID_NINJASCSI_32UDE_MELCO_II, 122 .subvendor = PCI_ANY_ID, 123 .subdevice = PCI_ANY_ID, 124 .driver_data = MODEL_PCI_MELCO, 125 }, 126 {0,0,}, 127 }; 128 MODULE_DEVICE_TABLE(pci, nsp32_pci_table); 129 130 static nsp32_hw_data nsp32_data_base; /* probe <-> detect glue */ 131 132 133 /* 134 * Period/AckWidth speed conversion table 135 * 136 * Note: This period/ackwidth speed table must be in descending order. 137 */ 138 static nsp32_sync_table nsp32_sync_table_40M[] = { 139 /* {PNo, AW, SP, EP, SREQ smpl} Speed(MB/s) Period AckWidth */ 140 {0x1, 0, 0x0c, 0x0c, SMPL_40M}, /* 20.0 : 50ns, 25ns */ 141 {0x2, 0, 0x0d, 0x18, SMPL_40M}, /* 13.3 : 75ns, 25ns */ 142 {0x3, 1, 0x19, 0x19, SMPL_40M}, /* 10.0 : 100ns, 50ns */ 143 {0x4, 1, 0x1a, 0x1f, SMPL_20M}, /* 8.0 : 125ns, 50ns */ 144 {0x5, 2, 0x20, 0x25, SMPL_20M}, /* 6.7 : 150ns, 75ns */ 145 {0x6, 2, 0x26, 0x31, SMPL_20M}, /* 5.7 : 175ns, 75ns */ 146 {0x7, 3, 0x32, 0x32, SMPL_20M}, /* 5.0 : 200ns, 100ns */ 147 {0x8, 3, 0x33, 0x38, SMPL_10M}, /* 4.4 : 225ns, 100ns */ 148 {0x9, 3, 0x39, 0x3e, SMPL_10M}, /* 4.0 : 250ns, 100ns */ 149 }; 150 151 static nsp32_sync_table nsp32_sync_table_20M[] = { 152 {0x1, 0, 0x19, 0x19, SMPL_40M}, /* 10.0 : 100ns, 50ns */ 153 {0x2, 0, 0x1a, 0x25, SMPL_20M}, /* 6.7 : 150ns, 50ns */ 154 {0x3, 1, 0x26, 0x32, SMPL_20M}, /* 5.0 : 200ns, 100ns */ 155 {0x4, 1, 0x33, 0x3e, SMPL_10M}, /* 4.0 : 250ns, 100ns */ 156 {0x5, 2, 0x3f, 0x4b, SMPL_10M}, /* 3.3 : 300ns, 150ns */ 157 {0x6, 2, 0x4c, 0x57, SMPL_10M}, /* 2.8 : 350ns, 150ns */ 158 {0x7, 3, 0x58, 0x64, SMPL_10M}, /* 2.5 : 400ns, 200ns */ 159 {0x8, 3, 0x65, 0x70, SMPL_10M}, /* 2.2 : 450ns, 200ns */ 160 {0x9, 3, 0x71, 0x7d, SMPL_10M}, /* 2.0 : 500ns, 200ns */ 161 }; 162 163 static nsp32_sync_table nsp32_sync_table_pci[] = { 164 {0x1, 0, 0x0c, 0x0f, SMPL_40M}, /* 16.6 : 60ns, 30ns */ 165 {0x2, 0, 0x10, 0x16, SMPL_40M}, /* 11.1 : 90ns, 30ns */ 166 {0x3, 1, 0x17, 0x1e, SMPL_20M}, /* 8.3 : 120ns, 60ns */ 167 {0x4, 1, 0x1f, 0x25, SMPL_20M}, /* 6.7 : 150ns, 60ns */ 168 {0x5, 2, 0x26, 0x2d, SMPL_20M}, /* 5.6 : 180ns, 90ns */ 169 {0x6, 2, 0x2e, 0x34, SMPL_10M}, /* 4.8 : 210ns, 90ns */ 170 {0x7, 3, 0x35, 0x3c, SMPL_10M}, /* 4.2 : 240ns, 120ns */ 171 {0x8, 3, 0x3d, 0x43, SMPL_10M}, /* 3.7 : 270ns, 120ns */ 172 {0x9, 3, 0x44, 0x4b, SMPL_10M}, /* 3.3 : 300ns, 120ns */ 173 }; 174 175 /* 176 * function declaration 177 */ 178 /* module entry point */ 179 static int nsp32_probe (struct pci_dev *, const struct pci_device_id *); 180 static void nsp32_remove(struct pci_dev *); 181 static int __init init_nsp32 (void); 182 static void __exit exit_nsp32 (void); 183 184 /* struct struct scsi_host_template */ 185 static int nsp32_show_info (struct seq_file *, struct Scsi_Host *); 186 187 static int nsp32_detect (struct pci_dev *pdev); 188 static int nsp32_queuecommand(struct Scsi_Host *, struct scsi_cmnd *); 189 static const char *nsp32_info (struct Scsi_Host *); 190 static int nsp32_release (struct Scsi_Host *); 191 192 /* SCSI error handler */ 193 static int nsp32_eh_abort (struct scsi_cmnd *); 194 static int nsp32_eh_host_reset(struct scsi_cmnd *); 195 196 /* generate SCSI message */ 197 static void nsp32_build_identify(struct scsi_cmnd *); 198 static void nsp32_build_nop (struct scsi_cmnd *); 199 static void nsp32_build_reject (struct scsi_cmnd *); 200 static void nsp32_build_sdtr (struct scsi_cmnd *, unsigned char, unsigned char); 201 202 /* SCSI message handler */ 203 static int nsp32_busfree_occur(struct scsi_cmnd *, unsigned short); 204 static void nsp32_msgout_occur (struct scsi_cmnd *); 205 static void nsp32_msgin_occur (struct scsi_cmnd *, unsigned long, unsigned short); 206 207 static int nsp32_setup_sg_table (struct scsi_cmnd *); 208 static int nsp32_selection_autopara(struct scsi_cmnd *); 209 static int nsp32_selection_autoscsi(struct scsi_cmnd *); 210 static void nsp32_scsi_done (struct scsi_cmnd *); 211 static int nsp32_arbitration (struct scsi_cmnd *, unsigned int); 212 static int nsp32_reselection (struct scsi_cmnd *, unsigned char); 213 static void nsp32_adjust_busfree (struct scsi_cmnd *, unsigned int); 214 static void nsp32_restart_autoscsi (struct scsi_cmnd *, unsigned short); 215 216 /* SCSI SDTR */ 217 static void nsp32_analyze_sdtr (struct scsi_cmnd *); 218 static int nsp32_search_period_entry(nsp32_hw_data *, nsp32_target *, unsigned char); 219 static void nsp32_set_async (nsp32_hw_data *, nsp32_target *); 220 static void nsp32_set_max_sync (nsp32_hw_data *, nsp32_target *, unsigned char *, unsigned char *); 221 static void nsp32_set_sync_entry (nsp32_hw_data *, nsp32_target *, int, unsigned char); 222 223 /* SCSI bus status handler */ 224 static void nsp32_wait_req (nsp32_hw_data *, int); 225 static void nsp32_wait_sack (nsp32_hw_data *, int); 226 static void nsp32_sack_assert (nsp32_hw_data *); 227 static void nsp32_sack_negate (nsp32_hw_data *); 228 static void nsp32_do_bus_reset(nsp32_hw_data *); 229 230 /* hardware interrupt handler */ 231 static irqreturn_t do_nsp32_isr(int, void *); 232 233 /* initialize hardware */ 234 static int nsp32hw_init(nsp32_hw_data *); 235 236 /* EEPROM handler */ 237 static int nsp32_getprom_param (nsp32_hw_data *); 238 static int nsp32_getprom_at24 (nsp32_hw_data *); 239 static int nsp32_getprom_c16 (nsp32_hw_data *); 240 static void nsp32_prom_start (nsp32_hw_data *); 241 static void nsp32_prom_stop (nsp32_hw_data *); 242 static int nsp32_prom_read (nsp32_hw_data *, int); 243 static int nsp32_prom_read_bit (nsp32_hw_data *); 244 static void nsp32_prom_write_bit(nsp32_hw_data *, int); 245 static void nsp32_prom_set (nsp32_hw_data *, int, int); 246 static int nsp32_prom_get (nsp32_hw_data *, int); 247 248 /* debug/warning/info message */ 249 static void nsp32_message (const char *, int, char *, char *, ...); 250 #ifdef NSP32_DEBUG 251 static void nsp32_dmessage(const char *, int, int, char *, ...); 252 #endif 253 254 /* 255 * max_sectors is currently limited up to 128. 256 */ 257 static struct scsi_host_template nsp32_template = { 258 .proc_name = "nsp32", 259 .name = "Workbit NinjaSCSI-32Bi/UDE", 260 .show_info = nsp32_show_info, 261 .info = nsp32_info, 262 .queuecommand = nsp32_queuecommand, 263 .can_queue = 1, 264 .sg_tablesize = NSP32_SG_SIZE, 265 .max_sectors = 128, 266 .this_id = NSP32_HOST_SCSIID, 267 .dma_boundary = PAGE_SIZE - 1, 268 .eh_abort_handler = nsp32_eh_abort, 269 .eh_host_reset_handler = nsp32_eh_host_reset, 270 /* .highmem_io = 1, */ 271 }; 272 273 #include "nsp32_io.h" 274 275 /*********************************************************************** 276 * debug, error print 277 */ 278 #ifndef NSP32_DEBUG 279 # define NSP32_DEBUG_MASK 0x000000 280 # define nsp32_msg(type, args...) nsp32_message ("", 0, (type), args) 281 # define nsp32_dbg(mask, args...) /* */ 282 #else 283 # define NSP32_DEBUG_MASK 0xffffff 284 # define nsp32_msg(type, args...) \ 285 nsp32_message (__func__, __LINE__, (type), args) 286 # define nsp32_dbg(mask, args...) \ 287 nsp32_dmessage(__func__, __LINE__, (mask), args) 288 #endif 289 290 #define NSP32_DEBUG_QUEUECOMMAND BIT(0) 291 #define NSP32_DEBUG_REGISTER BIT(1) 292 #define NSP32_DEBUG_AUTOSCSI BIT(2) 293 #define NSP32_DEBUG_INTR BIT(3) 294 #define NSP32_DEBUG_SGLIST BIT(4) 295 #define NSP32_DEBUG_BUSFREE BIT(5) 296 #define NSP32_DEBUG_CDB_CONTENTS BIT(6) 297 #define NSP32_DEBUG_RESELECTION BIT(7) 298 #define NSP32_DEBUG_MSGINOCCUR BIT(8) 299 #define NSP32_DEBUG_EEPROM BIT(9) 300 #define NSP32_DEBUG_MSGOUTOCCUR BIT(10) 301 #define NSP32_DEBUG_BUSRESET BIT(11) 302 #define NSP32_DEBUG_RESTART BIT(12) 303 #define NSP32_DEBUG_SYNC BIT(13) 304 #define NSP32_DEBUG_WAIT BIT(14) 305 #define NSP32_DEBUG_TARGETFLAG BIT(15) 306 #define NSP32_DEBUG_PROC BIT(16) 307 #define NSP32_DEBUG_INIT BIT(17) 308 #define NSP32_SPECIAL_PRINT_REGISTER BIT(20) 309 310 #define NSP32_DEBUG_BUF_LEN 100 311 312 static void nsp32_message(const char *func, int line, char *type, char *fmt, ...) 313 { 314 va_list args; 315 char buf[NSP32_DEBUG_BUF_LEN]; 316 317 va_start(args, fmt); 318 vsnprintf(buf, sizeof(buf), fmt, args); 319 va_end(args); 320 321 #ifndef NSP32_DEBUG 322 printk("%snsp32: %s\n", type, buf); 323 #else 324 printk("%snsp32: %s (%d): %s\n", type, func, line, buf); 325 #endif 326 } 327 328 #ifdef NSP32_DEBUG 329 static void nsp32_dmessage(const char *func, int line, int mask, char *fmt, ...) 330 { 331 va_list args; 332 char buf[NSP32_DEBUG_BUF_LEN]; 333 334 va_start(args, fmt); 335 vsnprintf(buf, sizeof(buf), fmt, args); 336 va_end(args); 337 338 if (mask & NSP32_DEBUG_MASK) { 339 printk("nsp32-debug: 0x%x %s (%d): %s\n", mask, func, line, buf); 340 } 341 } 342 #endif 343 344 #ifdef NSP32_DEBUG 345 # include "nsp32_debug.c" 346 #else 347 # define show_command(arg) /* */ 348 # define show_busphase(arg) /* */ 349 # define show_autophase(arg) /* */ 350 #endif 351 352 /* 353 * IDENTIFY Message 354 */ 355 static void nsp32_build_identify(struct scsi_cmnd *SCpnt) 356 { 357 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 358 int pos = data->msgout_len; 359 int mode = FALSE; 360 361 /* XXX: Auto DiscPriv detection is progressing... */ 362 if (disc_priv == 0) { 363 /* mode = TRUE; */ 364 } 365 366 data->msgoutbuf[pos] = IDENTIFY(mode, SCpnt->device->lun); pos++; 367 368 data->msgout_len = pos; 369 } 370 371 /* 372 * SDTR Message Routine 373 */ 374 static void nsp32_build_sdtr(struct scsi_cmnd *SCpnt, 375 unsigned char period, 376 unsigned char offset) 377 { 378 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 379 int pos = data->msgout_len; 380 381 data->msgoutbuf[pos] = EXTENDED_MESSAGE; pos++; 382 data->msgoutbuf[pos] = EXTENDED_SDTR_LEN; pos++; 383 data->msgoutbuf[pos] = EXTENDED_SDTR; pos++; 384 data->msgoutbuf[pos] = period; pos++; 385 data->msgoutbuf[pos] = offset; pos++; 386 387 data->msgout_len = pos; 388 } 389 390 /* 391 * No Operation Message 392 */ 393 static void nsp32_build_nop(struct scsi_cmnd *SCpnt) 394 { 395 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 396 int pos = data->msgout_len; 397 398 if (pos != 0) { 399 nsp32_msg(KERN_WARNING, 400 "Some messages are already contained!"); 401 return; 402 } 403 404 data->msgoutbuf[pos] = NOP; pos++; 405 data->msgout_len = pos; 406 } 407 408 /* 409 * Reject Message 410 */ 411 static void nsp32_build_reject(struct scsi_cmnd *SCpnt) 412 { 413 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 414 int pos = data->msgout_len; 415 416 data->msgoutbuf[pos] = MESSAGE_REJECT; pos++; 417 data->msgout_len = pos; 418 } 419 420 /* 421 * timer 422 */ 423 #if 0 424 static void nsp32_start_timer(struct scsi_cmnd *SCpnt, int time) 425 { 426 unsigned int base = SCpnt->host->io_port; 427 428 nsp32_dbg(NSP32_DEBUG_INTR, "timer=%d", time); 429 430 if (time & (~TIMER_CNT_MASK)) { 431 nsp32_dbg(NSP32_DEBUG_INTR, "timer set overflow"); 432 } 433 434 nsp32_write2(base, TIMER_SET, time & TIMER_CNT_MASK); 435 } 436 #endif 437 438 439 /* 440 * set SCSI command and other parameter to asic, and start selection phase 441 */ 442 static int nsp32_selection_autopara(struct scsi_cmnd *SCpnt) 443 { 444 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 445 unsigned int base = SCpnt->device->host->io_port; 446 unsigned int host_id = SCpnt->device->host->this_id; 447 unsigned char target = scmd_id(SCpnt); 448 nsp32_autoparam *param = data->autoparam; 449 unsigned char phase; 450 int i, ret; 451 unsigned int msgout; 452 u16_le s; 453 454 nsp32_dbg(NSP32_DEBUG_AUTOSCSI, "in"); 455 456 /* 457 * check bus free 458 */ 459 phase = nsp32_read1(base, SCSI_BUS_MONITOR); 460 if (phase != BUSMON_BUS_FREE) { 461 nsp32_msg(KERN_WARNING, "bus busy"); 462 show_busphase(phase & BUSMON_PHASE_MASK); 463 SCpnt->result = DID_BUS_BUSY << 16; 464 return FALSE; 465 } 466 467 /* 468 * message out 469 * 470 * Note: If the range of msgout_len is 1 - 3, fill scsi_msgout. 471 * over 3 messages needs another routine. 472 */ 473 if (data->msgout_len == 0) { 474 nsp32_msg(KERN_ERR, "SCSI MsgOut without any message!"); 475 SCpnt->result = DID_ERROR << 16; 476 return FALSE; 477 } else if (data->msgout_len > 0 && data->msgout_len <= 3) { 478 msgout = 0; 479 for (i = 0; i < data->msgout_len; i++) { 480 /* 481 * the sending order of the message is: 482 * MCNT 3: MSG#0 -> MSG#1 -> MSG#2 483 * MCNT 2: MSG#1 -> MSG#2 484 * MCNT 1: MSG#2 485 */ 486 msgout >>= 8; 487 msgout |= ((unsigned int)(data->msgoutbuf[i]) << 24); 488 } 489 msgout |= MV_VALID; /* MV valid */ 490 msgout |= (unsigned int)data->msgout_len; /* len */ 491 } else { 492 /* data->msgout_len > 3 */ 493 msgout = 0; 494 } 495 496 // nsp_dbg(NSP32_DEBUG_AUTOSCSI, "sel time out=0x%x\n", nsp32_read2(base, SEL_TIME_OUT)); 497 // nsp32_write2(base, SEL_TIME_OUT, SEL_TIMEOUT_TIME); 498 499 /* 500 * setup asic parameter 501 */ 502 memset(param, 0, sizeof(nsp32_autoparam)); 503 504 /* cdb */ 505 for (i = 0; i < SCpnt->cmd_len; i++) { 506 param->cdb[4 * i] = SCpnt->cmnd[i]; 507 } 508 509 /* outgoing messages */ 510 param->msgout = cpu_to_le32(msgout); 511 512 /* syncreg, ackwidth, target id, SREQ sampling rate */ 513 param->syncreg = data->cur_target->syncreg; 514 param->ackwidth = data->cur_target->ackwidth; 515 param->target_id = BIT(host_id) | BIT(target); 516 param->sample_reg = data->cur_target->sample_reg; 517 518 // nsp32_dbg(NSP32_DEBUG_AUTOSCSI, "sample rate=0x%x\n", data->cur_target->sample_reg); 519 520 /* command control */ 521 param->command_control = cpu_to_le16(CLEAR_CDB_FIFO_POINTER | 522 AUTOSCSI_START | 523 AUTO_MSGIN_00_OR_04 | 524 AUTO_MSGIN_02 | 525 AUTO_ATN ); 526 527 528 /* transfer control */ 529 s = 0; 530 switch (data->trans_method) { 531 case NSP32_TRANSFER_BUSMASTER: 532 s |= BM_START; 533 break; 534 case NSP32_TRANSFER_MMIO: 535 s |= CB_MMIO_MODE; 536 break; 537 case NSP32_TRANSFER_PIO: 538 s |= CB_IO_MODE; 539 break; 540 default: 541 nsp32_msg(KERN_ERR, "unknown trans_method"); 542 break; 543 } 544 /* 545 * OR-ed BLIEND_MODE, FIFO intr is decreased, instead of PCI bus waits. 546 * For bus master transfer, it's taken off. 547 */ 548 s |= (TRANSFER_GO | ALL_COUNTER_CLR); 549 param->transfer_control = cpu_to_le16(s); 550 551 /* sg table addr */ 552 param->sgt_pointer = cpu_to_le32(data->cur_lunt->sglun_paddr); 553 554 /* 555 * transfer parameter to ASIC 556 */ 557 nsp32_write4(base, SGT_ADR, data->auto_paddr); 558 nsp32_write2(base, COMMAND_CONTROL, CLEAR_CDB_FIFO_POINTER | 559 AUTO_PARAMETER ); 560 561 /* 562 * Check arbitration 563 */ 564 ret = nsp32_arbitration(SCpnt, base); 565 566 return ret; 567 } 568 569 570 /* 571 * Selection with AUTO SCSI (without AUTO PARAMETER) 572 */ 573 static int nsp32_selection_autoscsi(struct scsi_cmnd *SCpnt) 574 { 575 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 576 unsigned int base = SCpnt->device->host->io_port; 577 unsigned int host_id = SCpnt->device->host->this_id; 578 unsigned char target = scmd_id(SCpnt); 579 unsigned char phase; 580 int status; 581 unsigned short command = 0; 582 unsigned int msgout = 0; 583 unsigned short execph; 584 int i; 585 586 nsp32_dbg(NSP32_DEBUG_AUTOSCSI, "in"); 587 588 /* 589 * IRQ disable 590 */ 591 nsp32_write2(base, IRQ_CONTROL, IRQ_CONTROL_ALL_IRQ_MASK); 592 593 /* 594 * check bus line 595 */ 596 phase = nsp32_read1(base, SCSI_BUS_MONITOR); 597 if ((phase & BUSMON_BSY) || (phase & BUSMON_SEL)) { 598 nsp32_msg(KERN_WARNING, "bus busy"); 599 SCpnt->result = DID_BUS_BUSY << 16; 600 status = 1; 601 goto out; 602 } 603 604 /* 605 * clear execph 606 */ 607 execph = nsp32_read2(base, SCSI_EXECUTE_PHASE); 608 609 /* 610 * clear FIFO counter to set CDBs 611 */ 612 nsp32_write2(base, COMMAND_CONTROL, CLEAR_CDB_FIFO_POINTER); 613 614 /* 615 * set CDB0 - CDB15 616 */ 617 for (i = 0; i < SCpnt->cmd_len; i++) { 618 nsp32_write1(base, COMMAND_DATA, SCpnt->cmnd[i]); 619 } 620 nsp32_dbg(NSP32_DEBUG_CDB_CONTENTS, "CDB[0]=[0x%x]", SCpnt->cmnd[0]); 621 622 /* 623 * set SCSIOUT LATCH(initiator)/TARGET(target) (OR-ed) ID 624 */ 625 nsp32_write1(base, SCSI_OUT_LATCH_TARGET_ID, BIT(host_id) | BIT(target)); 626 627 /* 628 * set SCSI MSGOUT REG 629 * 630 * Note: If the range of msgout_len is 1 - 3, fill scsi_msgout. 631 * over 3 messages needs another routine. 632 */ 633 if (data->msgout_len == 0) { 634 nsp32_msg(KERN_ERR, "SCSI MsgOut without any message!"); 635 SCpnt->result = DID_ERROR << 16; 636 status = 1; 637 goto out; 638 } else if (data->msgout_len > 0 && data->msgout_len <= 3) { 639 msgout = 0; 640 for (i = 0; i < data->msgout_len; i++) { 641 /* 642 * the sending order of the message is: 643 * MCNT 3: MSG#0 -> MSG#1 -> MSG#2 644 * MCNT 2: MSG#1 -> MSG#2 645 * MCNT 1: MSG#2 646 */ 647 msgout >>= 8; 648 msgout |= ((unsigned int)(data->msgoutbuf[i]) << 24); 649 } 650 msgout |= MV_VALID; /* MV valid */ 651 msgout |= (unsigned int)data->msgout_len; /* len */ 652 nsp32_write4(base, SCSI_MSG_OUT, msgout); 653 } else { 654 /* data->msgout_len > 3 */ 655 nsp32_write4(base, SCSI_MSG_OUT, 0); 656 } 657 658 /* 659 * set selection timeout(= 250ms) 660 */ 661 nsp32_write2(base, SEL_TIME_OUT, SEL_TIMEOUT_TIME); 662 663 /* 664 * set SREQ hazard killer sampling rate 665 * 666 * TODO: sample_rate (BASE+0F) is 0 when internal clock = 40MHz. 667 * check other internal clock! 668 */ 669 nsp32_write1(base, SREQ_SMPL_RATE, data->cur_target->sample_reg); 670 671 /* 672 * clear Arbit 673 */ 674 nsp32_write1(base, SET_ARBIT, ARBIT_CLEAR); 675 676 /* 677 * set SYNCREG 678 * Don't set BM_START_ADR before setting this register. 679 */ 680 nsp32_write1(base, SYNC_REG, data->cur_target->syncreg); 681 682 /* 683 * set ACKWIDTH 684 */ 685 nsp32_write1(base, ACK_WIDTH, data->cur_target->ackwidth); 686 687 nsp32_dbg(NSP32_DEBUG_AUTOSCSI, 688 "syncreg=0x%x, ackwidth=0x%x, sgtpaddr=0x%x, id=0x%x", 689 nsp32_read1(base, SYNC_REG), nsp32_read1(base, ACK_WIDTH), 690 nsp32_read4(base, SGT_ADR), nsp32_read1(base, SCSI_OUT_LATCH_TARGET_ID)); 691 nsp32_dbg(NSP32_DEBUG_AUTOSCSI, "msgout_len=%d, msgout=0x%x", 692 data->msgout_len, msgout); 693 694 /* 695 * set SGT ADDR (physical address) 696 */ 697 nsp32_write4(base, SGT_ADR, data->cur_lunt->sglun_paddr); 698 699 /* 700 * set TRANSFER CONTROL REG 701 */ 702 command = 0; 703 command |= (TRANSFER_GO | ALL_COUNTER_CLR); 704 if (data->trans_method & NSP32_TRANSFER_BUSMASTER) { 705 if (scsi_bufflen(SCpnt) > 0) { 706 command |= BM_START; 707 } 708 } else if (data->trans_method & NSP32_TRANSFER_MMIO) { 709 command |= CB_MMIO_MODE; 710 } else if (data->trans_method & NSP32_TRANSFER_PIO) { 711 command |= CB_IO_MODE; 712 } 713 nsp32_write2(base, TRANSFER_CONTROL, command); 714 715 /* 716 * start AUTO SCSI, kick off arbitration 717 */ 718 command = (CLEAR_CDB_FIFO_POINTER | 719 AUTOSCSI_START | 720 AUTO_MSGIN_00_OR_04 | 721 AUTO_MSGIN_02 | 722 AUTO_ATN ); 723 nsp32_write2(base, COMMAND_CONTROL, command); 724 725 /* 726 * Check arbitration 727 */ 728 status = nsp32_arbitration(SCpnt, base); 729 730 out: 731 /* 732 * IRQ enable 733 */ 734 nsp32_write2(base, IRQ_CONTROL, 0); 735 736 return status; 737 } 738 739 740 /* 741 * Arbitration Status Check 742 * 743 * Note: Arbitration counter is waited during ARBIT_GO is not lifting. 744 * Using udelay(1) consumes CPU time and system time, but 745 * arbitration delay time is defined minimal 2.4us in SCSI 746 * specification, thus udelay works as coarse grained wait timer. 747 */ 748 static int nsp32_arbitration(struct scsi_cmnd *SCpnt, unsigned int base) 749 { 750 unsigned char arbit; 751 int status = TRUE; 752 int time = 0; 753 754 do { 755 arbit = nsp32_read1(base, ARBIT_STATUS); 756 time++; 757 } while ((arbit & (ARBIT_WIN | ARBIT_FAIL)) == 0 && 758 (time <= ARBIT_TIMEOUT_TIME)); 759 760 nsp32_dbg(NSP32_DEBUG_AUTOSCSI, 761 "arbit: 0x%x, delay time: %d", arbit, time); 762 763 if (arbit & ARBIT_WIN) { 764 /* Arbitration succeeded */ 765 SCpnt->result = DID_OK << 16; 766 nsp32_index_write1(base, EXT_PORT, LED_ON); /* PCI LED on */ 767 } else if (arbit & ARBIT_FAIL) { 768 /* Arbitration failed */ 769 SCpnt->result = DID_BUS_BUSY << 16; 770 status = FALSE; 771 } else { 772 /* 773 * unknown error or ARBIT_GO timeout, 774 * something lock up! guess no connection. 775 */ 776 nsp32_dbg(NSP32_DEBUG_AUTOSCSI, "arbit timeout"); 777 SCpnt->result = DID_NO_CONNECT << 16; 778 status = FALSE; 779 } 780 781 /* 782 * clear Arbit 783 */ 784 nsp32_write1(base, SET_ARBIT, ARBIT_CLEAR); 785 786 return status; 787 } 788 789 790 /* 791 * reselection 792 * 793 * Note: This reselection routine is called from msgin_occur, 794 * reselection target id&lun must be already set. 795 * SCSI-2 says IDENTIFY implies RESTORE_POINTER operation. 796 */ 797 static int nsp32_reselection(struct scsi_cmnd *SCpnt, unsigned char newlun) 798 { 799 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 800 unsigned int host_id = SCpnt->device->host->this_id; 801 unsigned int base = SCpnt->device->host->io_port; 802 unsigned char tmpid, newid; 803 804 nsp32_dbg(NSP32_DEBUG_RESELECTION, "enter"); 805 806 /* 807 * calculate reselected SCSI ID 808 */ 809 tmpid = nsp32_read1(base, RESELECT_ID); 810 tmpid &= (~BIT(host_id)); 811 newid = 0; 812 while (tmpid) { 813 if (tmpid & 1) { 814 break; 815 } 816 tmpid >>= 1; 817 newid++; 818 } 819 820 /* 821 * If reselected New ID:LUN is not existed 822 * or current nexus is not existed, unexpected 823 * reselection is occurred. Send reject message. 824 */ 825 if (newid >= ARRAY_SIZE(data->lunt) || newlun >= ARRAY_SIZE(data->lunt[0])) { 826 nsp32_msg(KERN_WARNING, "unknown id/lun"); 827 return FALSE; 828 } else if(data->lunt[newid][newlun].SCpnt == NULL) { 829 nsp32_msg(KERN_WARNING, "no SCSI command is processing"); 830 return FALSE; 831 } 832 833 data->cur_id = newid; 834 data->cur_lun = newlun; 835 data->cur_target = &(data->target[newid]); 836 data->cur_lunt = &(data->lunt[newid][newlun]); 837 838 /* reset SACK/SavedACK counter (or ALL clear?) */ 839 nsp32_write4(base, CLR_COUNTER, CLRCOUNTER_ALLMASK); 840 841 return TRUE; 842 } 843 844 845 /* 846 * nsp32_setup_sg_table - build scatter gather list for transfer data 847 * with bus master. 848 * 849 * Note: NinjaSCSI-32Bi/UDE bus master can not transfer over 64KB at a time. 850 */ 851 static int nsp32_setup_sg_table(struct scsi_cmnd *SCpnt) 852 { 853 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 854 struct scatterlist *sg; 855 nsp32_sgtable *sgt = data->cur_lunt->sglun->sgt; 856 int num, i; 857 u32_le l; 858 859 if (sgt == NULL) { 860 nsp32_dbg(NSP32_DEBUG_SGLIST, "SGT == null"); 861 return FALSE; 862 } 863 864 num = scsi_dma_map(SCpnt); 865 if (!num) 866 return TRUE; 867 else if (num < 0) 868 return FALSE; 869 else { 870 scsi_for_each_sg(SCpnt, sg, num, i) { 871 /* 872 * Build nsp32_sglist, substitute sg dma addresses. 873 */ 874 sgt[i].addr = cpu_to_le32(sg_dma_address(sg)); 875 sgt[i].len = cpu_to_le32(sg_dma_len(sg)); 876 877 if (le32_to_cpu(sgt[i].len) > 0x10000) { 878 nsp32_msg(KERN_ERR, 879 "can't transfer over 64KB at a time, size=0x%lx", le32_to_cpu(sgt[i].len)); 880 return FALSE; 881 } 882 nsp32_dbg(NSP32_DEBUG_SGLIST, 883 "num 0x%x : addr 0x%lx len 0x%lx", 884 i, 885 le32_to_cpu(sgt[i].addr), 886 le32_to_cpu(sgt[i].len )); 887 } 888 889 /* set end mark */ 890 l = le32_to_cpu(sgt[num-1].len); 891 sgt[num-1].len = cpu_to_le32(l | SGTEND); 892 } 893 894 return TRUE; 895 } 896 897 static int nsp32_queuecommand_lck(struct scsi_cmnd *SCpnt, void (*done)(struct scsi_cmnd *)) 898 { 899 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 900 nsp32_target *target; 901 nsp32_lunt *cur_lunt; 902 int ret; 903 904 nsp32_dbg(NSP32_DEBUG_QUEUECOMMAND, 905 "enter. target: 0x%x LUN: 0x%llx cmnd: 0x%x cmndlen: 0x%x " 906 "use_sg: 0x%x reqbuf: 0x%lx reqlen: 0x%x", 907 SCpnt->device->id, SCpnt->device->lun, SCpnt->cmnd[0], SCpnt->cmd_len, 908 scsi_sg_count(SCpnt), scsi_sglist(SCpnt), scsi_bufflen(SCpnt)); 909 910 if (data->CurrentSC != NULL) { 911 nsp32_msg(KERN_ERR, "Currentsc != NULL. Cancel this command request"); 912 data->CurrentSC = NULL; 913 SCpnt->result = DID_NO_CONNECT << 16; 914 done(SCpnt); 915 return 0; 916 } 917 918 /* check target ID is not same as this initiator ID */ 919 if (scmd_id(SCpnt) == SCpnt->device->host->this_id) { 920 nsp32_dbg(NSP32_DEBUG_QUEUECOMMAND, "target==host???"); 921 SCpnt->result = DID_BAD_TARGET << 16; 922 done(SCpnt); 923 return 0; 924 } 925 926 /* check target LUN is allowable value */ 927 if (SCpnt->device->lun >= MAX_LUN) { 928 nsp32_dbg(NSP32_DEBUG_QUEUECOMMAND, "no more lun"); 929 SCpnt->result = DID_BAD_TARGET << 16; 930 done(SCpnt); 931 return 0; 932 } 933 934 show_command(SCpnt); 935 936 SCpnt->scsi_done = done; 937 data->CurrentSC = SCpnt; 938 SCpnt->SCp.Status = CHECK_CONDITION; 939 SCpnt->SCp.Message = 0; 940 scsi_set_resid(SCpnt, scsi_bufflen(SCpnt)); 941 942 SCpnt->SCp.ptr = (char *)scsi_sglist(SCpnt); 943 SCpnt->SCp.this_residual = scsi_bufflen(SCpnt); 944 SCpnt->SCp.buffer = NULL; 945 SCpnt->SCp.buffers_residual = 0; 946 947 /* initialize data */ 948 data->msgout_len = 0; 949 data->msgin_len = 0; 950 cur_lunt = &(data->lunt[SCpnt->device->id][SCpnt->device->lun]); 951 cur_lunt->SCpnt = SCpnt; 952 cur_lunt->save_datp = 0; 953 cur_lunt->msgin03 = FALSE; 954 data->cur_lunt = cur_lunt; 955 data->cur_id = SCpnt->device->id; 956 data->cur_lun = SCpnt->device->lun; 957 958 ret = nsp32_setup_sg_table(SCpnt); 959 if (ret == FALSE) { 960 nsp32_msg(KERN_ERR, "SGT fail"); 961 SCpnt->result = DID_ERROR << 16; 962 nsp32_scsi_done(SCpnt); 963 return 0; 964 } 965 966 /* Build IDENTIFY */ 967 nsp32_build_identify(SCpnt); 968 969 /* 970 * If target is the first time to transfer after the reset 971 * (target don't have SDTR_DONE and SDTR_INITIATOR), sync 972 * message SDTR is needed to do synchronous transfer. 973 */ 974 target = &data->target[scmd_id(SCpnt)]; 975 data->cur_target = target; 976 977 if (!(target->sync_flag & (SDTR_DONE | SDTR_INITIATOR | SDTR_TARGET))) { 978 unsigned char period, offset; 979 980 if (trans_mode != ASYNC_MODE) { 981 nsp32_set_max_sync(data, target, &period, &offset); 982 nsp32_build_sdtr(SCpnt, period, offset); 983 target->sync_flag |= SDTR_INITIATOR; 984 } else { 985 nsp32_set_async(data, target); 986 target->sync_flag |= SDTR_DONE; 987 } 988 989 nsp32_dbg(NSP32_DEBUG_QUEUECOMMAND, 990 "SDTR: entry: %d start_period: 0x%x offset: 0x%x\n", 991 target->limit_entry, period, offset); 992 } else if (target->sync_flag & SDTR_INITIATOR) { 993 /* 994 * It was negotiating SDTR with target, sending from the 995 * initiator, but there are no chance to remove this flag. 996 * Set async because we don't get proper negotiation. 997 */ 998 nsp32_set_async(data, target); 999 target->sync_flag &= ~SDTR_INITIATOR; 1000 target->sync_flag |= SDTR_DONE; 1001 1002 nsp32_dbg(NSP32_DEBUG_QUEUECOMMAND, 1003 "SDTR_INITIATOR: fall back to async"); 1004 } else if (target->sync_flag & SDTR_TARGET) { 1005 /* 1006 * It was negotiating SDTR with target, sending from target, 1007 * but there are no chance to remove this flag. Set async 1008 * because we don't get proper negotiation. 1009 */ 1010 nsp32_set_async(data, target); 1011 target->sync_flag &= ~SDTR_TARGET; 1012 target->sync_flag |= SDTR_DONE; 1013 1014 nsp32_dbg(NSP32_DEBUG_QUEUECOMMAND, 1015 "Unknown SDTR from target is reached, fall back to async."); 1016 } 1017 1018 nsp32_dbg(NSP32_DEBUG_TARGETFLAG, 1019 "target: %d sync_flag: 0x%x syncreg: 0x%x ackwidth: 0x%x", 1020 SCpnt->device->id, target->sync_flag, target->syncreg, 1021 target->ackwidth); 1022 1023 /* Selection */ 1024 if (auto_param == 0) { 1025 ret = nsp32_selection_autopara(SCpnt); 1026 } else { 1027 ret = nsp32_selection_autoscsi(SCpnt); 1028 } 1029 1030 if (ret != TRUE) { 1031 nsp32_dbg(NSP32_DEBUG_QUEUECOMMAND, "selection fail"); 1032 nsp32_scsi_done(SCpnt); 1033 } 1034 1035 return 0; 1036 } 1037 1038 static DEF_SCSI_QCMD(nsp32_queuecommand) 1039 1040 /* initialize asic */ 1041 static int nsp32hw_init(nsp32_hw_data *data) 1042 { 1043 unsigned int base = data->BaseAddress; 1044 unsigned short irq_stat; 1045 unsigned long lc_reg; 1046 unsigned char power; 1047 1048 lc_reg = nsp32_index_read4(base, CFG_LATE_CACHE); 1049 if ((lc_reg & 0xff00) == 0) { 1050 lc_reg |= (0x20 << 8); 1051 nsp32_index_write2(base, CFG_LATE_CACHE, lc_reg & 0xffff); 1052 } 1053 1054 nsp32_write2(base, IRQ_CONTROL, IRQ_CONTROL_ALL_IRQ_MASK); 1055 nsp32_write2(base, TRANSFER_CONTROL, 0); 1056 nsp32_write4(base, BM_CNT, 0); 1057 nsp32_write2(base, SCSI_EXECUTE_PHASE, 0); 1058 1059 do { 1060 irq_stat = nsp32_read2(base, IRQ_STATUS); 1061 nsp32_dbg(NSP32_DEBUG_INIT, "irq_stat 0x%x", irq_stat); 1062 } while (irq_stat & IRQSTATUS_ANY_IRQ); 1063 1064 /* 1065 * Fill FIFO_FULL_SHLD, FIFO_EMPTY_SHLD. Below parameter is 1066 * designated by specification. 1067 */ 1068 if ((data->trans_method & NSP32_TRANSFER_PIO) || 1069 (data->trans_method & NSP32_TRANSFER_MMIO)) { 1070 nsp32_index_write1(base, FIFO_FULL_SHLD_COUNT, 0x40); 1071 nsp32_index_write1(base, FIFO_EMPTY_SHLD_COUNT, 0x40); 1072 } else if (data->trans_method & NSP32_TRANSFER_BUSMASTER) { 1073 nsp32_index_write1(base, FIFO_FULL_SHLD_COUNT, 0x10); 1074 nsp32_index_write1(base, FIFO_EMPTY_SHLD_COUNT, 0x60); 1075 } else { 1076 nsp32_dbg(NSP32_DEBUG_INIT, "unknown transfer mode"); 1077 } 1078 1079 nsp32_dbg(NSP32_DEBUG_INIT, "full 0x%x emp 0x%x", 1080 nsp32_index_read1(base, FIFO_FULL_SHLD_COUNT), 1081 nsp32_index_read1(base, FIFO_EMPTY_SHLD_COUNT)); 1082 1083 nsp32_index_write1(base, CLOCK_DIV, data->clock); 1084 nsp32_index_write1(base, BM_CYCLE, MEMRD_CMD1 | SGT_AUTO_PARA_MEMED_CMD); 1085 nsp32_write1(base, PARITY_CONTROL, 0); /* parity check is disable */ 1086 1087 /* 1088 * initialize MISC_WRRD register 1089 * 1090 * Note: Designated parameters is obeyed as following: 1091 * MISC_SCSI_DIRECTION_DETECTOR_SELECT: It must be set. 1092 * MISC_MASTER_TERMINATION_SELECT: It must be set. 1093 * MISC_BMREQ_NEGATE_TIMING_SEL: It should be set. 1094 * MISC_AUTOSEL_TIMING_SEL: It should be set. 1095 * MISC_BMSTOP_CHANGE2_NONDATA_PHASE: It should be set. 1096 * MISC_DELAYED_BMSTART: It's selected for safety. 1097 * 1098 * Note: If MISC_BMSTOP_CHANGE2_NONDATA_PHASE is set, then 1099 * we have to set TRANSFERCONTROL_BM_START as 0 and set 1100 * appropriate value before restarting bus master transfer. 1101 */ 1102 nsp32_index_write2(base, MISC_WR, 1103 (SCSI_DIRECTION_DETECTOR_SELECT | 1104 DELAYED_BMSTART | 1105 MASTER_TERMINATION_SELECT | 1106 BMREQ_NEGATE_TIMING_SEL | 1107 AUTOSEL_TIMING_SEL | 1108 BMSTOP_CHANGE2_NONDATA_PHASE)); 1109 1110 nsp32_index_write1(base, TERM_PWR_CONTROL, 0); 1111 power = nsp32_index_read1(base, TERM_PWR_CONTROL); 1112 if (!(power & SENSE)) { 1113 nsp32_msg(KERN_INFO, "term power on"); 1114 nsp32_index_write1(base, TERM_PWR_CONTROL, BPWR); 1115 } 1116 1117 nsp32_write2(base, TIMER_SET, TIMER_STOP); 1118 nsp32_write2(base, TIMER_SET, TIMER_STOP); /* Required 2 times */ 1119 1120 nsp32_write1(base, SYNC_REG, 0); 1121 nsp32_write1(base, ACK_WIDTH, 0); 1122 nsp32_write2(base, SEL_TIME_OUT, SEL_TIMEOUT_TIME); 1123 1124 /* 1125 * enable to select designated IRQ (except for 1126 * IRQSELECT_SERR, IRQSELECT_PERR, IRQSELECT_BMCNTERR) 1127 */ 1128 nsp32_index_write2(base, IRQ_SELECT, IRQSELECT_TIMER_IRQ | 1129 IRQSELECT_SCSIRESET_IRQ | 1130 IRQSELECT_FIFO_SHLD_IRQ | 1131 IRQSELECT_RESELECT_IRQ | 1132 IRQSELECT_PHASE_CHANGE_IRQ | 1133 IRQSELECT_AUTO_SCSI_SEQ_IRQ | 1134 // IRQSELECT_BMCNTERR_IRQ | 1135 IRQSELECT_TARGET_ABORT_IRQ | 1136 IRQSELECT_MASTER_ABORT_IRQ ); 1137 nsp32_write2(base, IRQ_CONTROL, 0); 1138 1139 /* PCI LED off */ 1140 nsp32_index_write1(base, EXT_PORT_DDR, LED_OFF); 1141 nsp32_index_write1(base, EXT_PORT, LED_OFF); 1142 1143 return TRUE; 1144 } 1145 1146 1147 /* interrupt routine */ 1148 static irqreturn_t do_nsp32_isr(int irq, void *dev_id) 1149 { 1150 nsp32_hw_data *data = dev_id; 1151 unsigned int base = data->BaseAddress; 1152 struct scsi_cmnd *SCpnt = data->CurrentSC; 1153 unsigned short auto_stat, irq_stat, trans_stat; 1154 unsigned char busmon, busphase; 1155 unsigned long flags; 1156 int ret; 1157 int handled = 0; 1158 struct Scsi_Host *host = data->Host; 1159 1160 spin_lock_irqsave(host->host_lock, flags); 1161 1162 /* 1163 * IRQ check, then enable IRQ mask 1164 */ 1165 irq_stat = nsp32_read2(base, IRQ_STATUS); 1166 nsp32_dbg(NSP32_DEBUG_INTR, 1167 "enter IRQ: %d, IRQstatus: 0x%x", irq, irq_stat); 1168 /* is this interrupt comes from Ninja asic? */ 1169 if ((irq_stat & IRQSTATUS_ANY_IRQ) == 0) { 1170 nsp32_dbg(NSP32_DEBUG_INTR, "shared interrupt: irq other 0x%x", irq_stat); 1171 goto out2; 1172 } 1173 handled = 1; 1174 nsp32_write2(base, IRQ_CONTROL, IRQ_CONTROL_ALL_IRQ_MASK); 1175 1176 busmon = nsp32_read1(base, SCSI_BUS_MONITOR); 1177 busphase = busmon & BUSMON_PHASE_MASK; 1178 1179 trans_stat = nsp32_read2(base, TRANSFER_STATUS); 1180 if ((irq_stat == 0xffff) && (trans_stat == 0xffff)) { 1181 nsp32_msg(KERN_INFO, "card disconnect"); 1182 if (data->CurrentSC != NULL) { 1183 nsp32_msg(KERN_INFO, "clean up current SCSI command"); 1184 SCpnt->result = DID_BAD_TARGET << 16; 1185 nsp32_scsi_done(SCpnt); 1186 } 1187 goto out; 1188 } 1189 1190 /* Timer IRQ */ 1191 if (irq_stat & IRQSTATUS_TIMER_IRQ) { 1192 nsp32_dbg(NSP32_DEBUG_INTR, "timer stop"); 1193 nsp32_write2(base, TIMER_SET, TIMER_STOP); 1194 goto out; 1195 } 1196 1197 /* SCSI reset */ 1198 if (irq_stat & IRQSTATUS_SCSIRESET_IRQ) { 1199 nsp32_msg(KERN_INFO, "detected someone do bus reset"); 1200 nsp32_do_bus_reset(data); 1201 if (SCpnt != NULL) { 1202 SCpnt->result = DID_RESET << 16; 1203 nsp32_scsi_done(SCpnt); 1204 } 1205 goto out; 1206 } 1207 1208 if (SCpnt == NULL) { 1209 nsp32_msg(KERN_WARNING, "SCpnt==NULL this can't be happened"); 1210 nsp32_msg(KERN_WARNING, "irq_stat=0x%x trans_stat=0x%x", irq_stat, trans_stat); 1211 goto out; 1212 } 1213 1214 /* 1215 * AutoSCSI Interrupt. 1216 * Note: This interrupt is occurred when AutoSCSI is finished. Then 1217 * check SCSIEXECUTEPHASE, and do appropriate action. Each phases are 1218 * recorded when AutoSCSI sequencer has been processed. 1219 */ 1220 if(irq_stat & IRQSTATUS_AUTOSCSI_IRQ) { 1221 /* getting SCSI executed phase */ 1222 auto_stat = nsp32_read2(base, SCSI_EXECUTE_PHASE); 1223 nsp32_write2(base, SCSI_EXECUTE_PHASE, 0); 1224 1225 /* Selection Timeout, go busfree phase. */ 1226 if (auto_stat & SELECTION_TIMEOUT) { 1227 nsp32_dbg(NSP32_DEBUG_INTR, 1228 "selection timeout occurred"); 1229 1230 SCpnt->result = DID_TIME_OUT << 16; 1231 nsp32_scsi_done(SCpnt); 1232 goto out; 1233 } 1234 1235 if (auto_stat & MSGOUT_PHASE) { 1236 /* 1237 * MsgOut phase was processed. 1238 * If MSG_IN_OCCUER is not set, then MsgOut phase is 1239 * completed. Thus, msgout_len must reset. Otherwise, 1240 * nothing to do here. If MSG_OUT_OCCUER is occurred, 1241 * then we will encounter the condition and check. 1242 */ 1243 if (!(auto_stat & MSG_IN_OCCUER) && 1244 (data->msgout_len <= 3)) { 1245 /* 1246 * !MSG_IN_OCCUER && msgout_len <=3 1247 * ---> AutoSCSI with MSGOUTreg is processed. 1248 */ 1249 data->msgout_len = 0; 1250 } 1251 1252 nsp32_dbg(NSP32_DEBUG_INTR, "MsgOut phase processed"); 1253 } 1254 1255 if ((auto_stat & DATA_IN_PHASE) && 1256 (scsi_get_resid(SCpnt) > 0) && 1257 ((nsp32_read2(base, FIFO_REST_CNT) & FIFO_REST_MASK) != 0)) { 1258 printk( "auto+fifo\n"); 1259 //nsp32_pio_read(SCpnt); 1260 } 1261 1262 if (auto_stat & (DATA_IN_PHASE | DATA_OUT_PHASE)) { 1263 /* DATA_IN_PHASE/DATA_OUT_PHASE was processed. */ 1264 nsp32_dbg(NSP32_DEBUG_INTR, 1265 "Data in/out phase processed"); 1266 1267 /* read BMCNT, SGT pointer addr */ 1268 nsp32_dbg(NSP32_DEBUG_INTR, "BMCNT=0x%lx", 1269 nsp32_read4(base, BM_CNT)); 1270 nsp32_dbg(NSP32_DEBUG_INTR, "addr=0x%lx", 1271 nsp32_read4(base, SGT_ADR)); 1272 nsp32_dbg(NSP32_DEBUG_INTR, "SACK=0x%lx", 1273 nsp32_read4(base, SACK_CNT)); 1274 nsp32_dbg(NSP32_DEBUG_INTR, "SSACK=0x%lx", 1275 nsp32_read4(base, SAVED_SACK_CNT)); 1276 1277 scsi_set_resid(SCpnt, 0); /* all data transferred! */ 1278 } 1279 1280 /* 1281 * MsgIn Occur 1282 */ 1283 if (auto_stat & MSG_IN_OCCUER) { 1284 nsp32_msgin_occur(SCpnt, irq_stat, auto_stat); 1285 } 1286 1287 /* 1288 * MsgOut Occur 1289 */ 1290 if (auto_stat & MSG_OUT_OCCUER) { 1291 nsp32_msgout_occur(SCpnt); 1292 } 1293 1294 /* 1295 * Bus Free Occur 1296 */ 1297 if (auto_stat & BUS_FREE_OCCUER) { 1298 ret = nsp32_busfree_occur(SCpnt, auto_stat); 1299 if (ret == TRUE) { 1300 goto out; 1301 } 1302 } 1303 1304 if (auto_stat & STATUS_PHASE) { 1305 /* 1306 * Read CSB and substitute CSB for SCpnt->result 1307 * to save status phase stutas byte. 1308 * scsi error handler checks host_byte (DID_*: 1309 * low level driver to indicate status), then checks 1310 * status_byte (SCSI status byte). 1311 */ 1312 SCpnt->result = (int)nsp32_read1(base, SCSI_CSB_IN); 1313 } 1314 1315 if (auto_stat & ILLEGAL_PHASE) { 1316 /* Illegal phase is detected. SACK is not back. */ 1317 nsp32_msg(KERN_WARNING, 1318 "AUTO SCSI ILLEGAL PHASE OCCUR!!!!"); 1319 1320 /* TODO: currently we don't have any action... bus reset? */ 1321 1322 /* 1323 * To send back SACK, assert, wait, and negate. 1324 */ 1325 nsp32_sack_assert(data); 1326 nsp32_wait_req(data, NEGATE); 1327 nsp32_sack_negate(data); 1328 1329 } 1330 1331 if (auto_stat & COMMAND_PHASE) { 1332 /* nothing to do */ 1333 nsp32_dbg(NSP32_DEBUG_INTR, "Command phase processed"); 1334 } 1335 1336 if (auto_stat & AUTOSCSI_BUSY) { 1337 /* AutoSCSI is running */ 1338 } 1339 1340 show_autophase(auto_stat); 1341 } 1342 1343 /* FIFO_SHLD_IRQ */ 1344 if (irq_stat & IRQSTATUS_FIFO_SHLD_IRQ) { 1345 nsp32_dbg(NSP32_DEBUG_INTR, "FIFO IRQ"); 1346 1347 switch(busphase) { 1348 case BUSPHASE_DATA_OUT: 1349 nsp32_dbg(NSP32_DEBUG_INTR, "fifo/write"); 1350 1351 //nsp32_pio_write(SCpnt); 1352 1353 break; 1354 1355 case BUSPHASE_DATA_IN: 1356 nsp32_dbg(NSP32_DEBUG_INTR, "fifo/read"); 1357 1358 //nsp32_pio_read(SCpnt); 1359 1360 break; 1361 1362 case BUSPHASE_STATUS: 1363 nsp32_dbg(NSP32_DEBUG_INTR, "fifo/status"); 1364 1365 SCpnt->SCp.Status = nsp32_read1(base, SCSI_CSB_IN); 1366 1367 break; 1368 default: 1369 nsp32_dbg(NSP32_DEBUG_INTR, "fifo/other phase"); 1370 nsp32_dbg(NSP32_DEBUG_INTR, "irq_stat=0x%x trans_stat=0x%x", irq_stat, trans_stat); 1371 show_busphase(busphase); 1372 break; 1373 } 1374 1375 goto out; 1376 } 1377 1378 /* Phase Change IRQ */ 1379 if (irq_stat & IRQSTATUS_PHASE_CHANGE_IRQ) { 1380 nsp32_dbg(NSP32_DEBUG_INTR, "phase change IRQ"); 1381 1382 switch(busphase) { 1383 case BUSPHASE_MESSAGE_IN: 1384 nsp32_dbg(NSP32_DEBUG_INTR, "phase chg/msg in"); 1385 nsp32_msgin_occur(SCpnt, irq_stat, 0); 1386 break; 1387 default: 1388 nsp32_msg(KERN_WARNING, "phase chg/other phase?"); 1389 nsp32_msg(KERN_WARNING, "irq_stat=0x%x trans_stat=0x%x\n", 1390 irq_stat, trans_stat); 1391 show_busphase(busphase); 1392 break; 1393 } 1394 goto out; 1395 } 1396 1397 /* PCI_IRQ */ 1398 if (irq_stat & IRQSTATUS_PCI_IRQ) { 1399 nsp32_dbg(NSP32_DEBUG_INTR, "PCI IRQ occurred"); 1400 /* Do nothing */ 1401 } 1402 1403 /* BMCNTERR_IRQ */ 1404 if (irq_stat & IRQSTATUS_BMCNTERR_IRQ) { 1405 nsp32_msg(KERN_ERR, "Received unexpected BMCNTERR IRQ! "); 1406 /* 1407 * TODO: To be implemented improving bus master 1408 * transfer reliability when BMCNTERR is occurred in 1409 * AutoSCSI phase described in specification. 1410 */ 1411 } 1412 1413 #if 0 1414 nsp32_dbg(NSP32_DEBUG_INTR, 1415 "irq_stat=0x%x trans_stat=0x%x", irq_stat, trans_stat); 1416 show_busphase(busphase); 1417 #endif 1418 1419 out: 1420 /* disable IRQ mask */ 1421 nsp32_write2(base, IRQ_CONTROL, 0); 1422 1423 out2: 1424 spin_unlock_irqrestore(host->host_lock, flags); 1425 1426 nsp32_dbg(NSP32_DEBUG_INTR, "exit"); 1427 1428 return IRQ_RETVAL(handled); 1429 } 1430 1431 1432 static int nsp32_show_info(struct seq_file *m, struct Scsi_Host *host) 1433 { 1434 unsigned long flags; 1435 nsp32_hw_data *data; 1436 int hostno; 1437 unsigned int base; 1438 unsigned char mode_reg; 1439 int id, speed; 1440 long model; 1441 1442 hostno = host->host_no; 1443 data = (nsp32_hw_data *)host->hostdata; 1444 base = host->io_port; 1445 1446 seq_puts(m, "NinjaSCSI-32 status\n\n"); 1447 seq_printf(m, "Driver version: %s, $Revision: 1.33 $\n", nsp32_release_version); 1448 seq_printf(m, "SCSI host No.: %d\n", hostno); 1449 seq_printf(m, "IRQ: %d\n", host->irq); 1450 seq_printf(m, "IO: 0x%lx-0x%lx\n", host->io_port, host->io_port + host->n_io_port - 1); 1451 seq_printf(m, "MMIO(virtual address): 0x%lx-0x%lx\n", host->base, host->base + data->MmioLength - 1); 1452 seq_printf(m, "sg_tablesize: %d\n", host->sg_tablesize); 1453 seq_printf(m, "Chip revision: 0x%x\n", (nsp32_read2(base, INDEX_REG) >> 8) & 0xff); 1454 1455 mode_reg = nsp32_index_read1(base, CHIP_MODE); 1456 model = data->pci_devid->driver_data; 1457 1458 #ifdef CONFIG_PM 1459 seq_printf(m, "Power Management: %s\n", (mode_reg & OPTF) ? "yes" : "no"); 1460 #endif 1461 seq_printf(m, "OEM: %ld, %s\n", (mode_reg & (OEM0|OEM1)), nsp32_model[model]); 1462 1463 spin_lock_irqsave(&(data->Lock), flags); 1464 seq_printf(m, "CurrentSC: 0x%p\n\n", data->CurrentSC); 1465 spin_unlock_irqrestore(&(data->Lock), flags); 1466 1467 1468 seq_puts(m, "SDTR status\n"); 1469 for (id = 0; id < ARRAY_SIZE(data->target); id++) { 1470 1471 seq_printf(m, "id %d: ", id); 1472 1473 if (id == host->this_id) { 1474 seq_puts(m, "----- NinjaSCSI-32 host adapter\n"); 1475 continue; 1476 } 1477 1478 if (data->target[id].sync_flag == SDTR_DONE) { 1479 if (data->target[id].period == 0 && 1480 data->target[id].offset == ASYNC_OFFSET ) { 1481 seq_puts(m, "async"); 1482 } else { 1483 seq_puts(m, " sync"); 1484 } 1485 } else { 1486 seq_puts(m, " none"); 1487 } 1488 1489 if (data->target[id].period != 0) { 1490 1491 speed = 1000000 / (data->target[id].period * 4); 1492 1493 seq_printf(m, " transfer %d.%dMB/s, offset %d", 1494 speed / 1000, 1495 speed % 1000, 1496 data->target[id].offset 1497 ); 1498 } 1499 seq_putc(m, '\n'); 1500 } 1501 return 0; 1502 } 1503 1504 1505 1506 /* 1507 * Reset parameters and call scsi_done for data->cur_lunt. 1508 * Be careful setting SCpnt->result = DID_* before calling this function. 1509 */ 1510 static void nsp32_scsi_done(struct scsi_cmnd *SCpnt) 1511 { 1512 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 1513 unsigned int base = SCpnt->device->host->io_port; 1514 1515 scsi_dma_unmap(SCpnt); 1516 1517 /* 1518 * clear TRANSFERCONTROL_BM_START 1519 */ 1520 nsp32_write2(base, TRANSFER_CONTROL, 0); 1521 nsp32_write4(base, BM_CNT, 0); 1522 1523 /* 1524 * call scsi_done 1525 */ 1526 (*SCpnt->scsi_done)(SCpnt); 1527 1528 /* 1529 * reset parameters 1530 */ 1531 data->cur_lunt->SCpnt = NULL; 1532 data->cur_lunt = NULL; 1533 data->cur_target = NULL; 1534 data->CurrentSC = NULL; 1535 } 1536 1537 1538 /* 1539 * Bus Free Occur 1540 * 1541 * Current Phase is BUSFREE. AutoSCSI is automatically execute BUSFREE phase 1542 * with ACK reply when below condition is matched: 1543 * MsgIn 00: Command Complete. 1544 * MsgIn 02: Save Data Pointer. 1545 * MsgIn 04: Disconnect. 1546 * In other case, unexpected BUSFREE is detected. 1547 */ 1548 static int nsp32_busfree_occur(struct scsi_cmnd *SCpnt, unsigned short execph) 1549 { 1550 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 1551 unsigned int base = SCpnt->device->host->io_port; 1552 1553 nsp32_dbg(NSP32_DEBUG_BUSFREE, "enter execph=0x%x", execph); 1554 show_autophase(execph); 1555 1556 nsp32_write4(base, BM_CNT, 0); 1557 nsp32_write2(base, TRANSFER_CONTROL, 0); 1558 1559 /* 1560 * MsgIn 02: Save Data Pointer 1561 * 1562 * VALID: 1563 * Save Data Pointer is received. Adjust pointer. 1564 * 1565 * NO-VALID: 1566 * SCSI-3 says if Save Data Pointer is not received, then we restart 1567 * processing and we can't adjust any SCSI data pointer in next data 1568 * phase. 1569 */ 1570 if (execph & MSGIN_02_VALID) { 1571 nsp32_dbg(NSP32_DEBUG_BUSFREE, "MsgIn02_Valid"); 1572 1573 /* 1574 * Check sack_cnt/saved_sack_cnt, then adjust sg table if 1575 * needed. 1576 */ 1577 if (!(execph & MSGIN_00_VALID) && 1578 ((execph & DATA_IN_PHASE) || (execph & DATA_OUT_PHASE))) { 1579 unsigned int sacklen, s_sacklen; 1580 1581 /* 1582 * Read SACK count and SAVEDSACK count, then compare. 1583 */ 1584 sacklen = nsp32_read4(base, SACK_CNT ); 1585 s_sacklen = nsp32_read4(base, SAVED_SACK_CNT); 1586 1587 /* 1588 * If SAVEDSACKCNT == 0, it means SavedDataPointer is 1589 * come after data transferring. 1590 */ 1591 if (s_sacklen > 0) { 1592 /* 1593 * Comparing between sack and savedsack to 1594 * check the condition of AutoMsgIn03. 1595 * 1596 * If they are same, set msgin03 == TRUE, 1597 * COMMANDCONTROL_AUTO_MSGIN_03 is enabled at 1598 * reselection. On the other hand, if they 1599 * aren't same, set msgin03 == FALSE, and 1600 * COMMANDCONTROL_AUTO_MSGIN_03 is disabled at 1601 * reselection. 1602 */ 1603 if (sacklen != s_sacklen) { 1604 data->cur_lunt->msgin03 = FALSE; 1605 } else { 1606 data->cur_lunt->msgin03 = TRUE; 1607 } 1608 1609 nsp32_adjust_busfree(SCpnt, s_sacklen); 1610 } 1611 } 1612 1613 /* This value has not substitude with valid value yet... */ 1614 //data->cur_lunt->save_datp = data->cur_datp; 1615 } else { 1616 /* 1617 * no processing. 1618 */ 1619 } 1620 1621 if (execph & MSGIN_03_VALID) { 1622 /* MsgIn03 was valid to be processed. No need processing. */ 1623 } 1624 1625 /* 1626 * target SDTR check 1627 */ 1628 if (data->cur_target->sync_flag & SDTR_INITIATOR) { 1629 /* 1630 * SDTR negotiation pulled by the initiator has not 1631 * finished yet. Fall back to ASYNC mode. 1632 */ 1633 nsp32_set_async(data, data->cur_target); 1634 data->cur_target->sync_flag &= ~SDTR_INITIATOR; 1635 data->cur_target->sync_flag |= SDTR_DONE; 1636 } else if (data->cur_target->sync_flag & SDTR_TARGET) { 1637 /* 1638 * SDTR negotiation pulled by the target has been 1639 * negotiating. 1640 */ 1641 if (execph & (MSGIN_00_VALID | MSGIN_04_VALID)) { 1642 /* 1643 * If valid message is received, then 1644 * negotiation is succeeded. 1645 */ 1646 } else { 1647 /* 1648 * On the contrary, if unexpected bus free is 1649 * occurred, then negotiation is failed. Fall 1650 * back to ASYNC mode. 1651 */ 1652 nsp32_set_async(data, data->cur_target); 1653 } 1654 data->cur_target->sync_flag &= ~SDTR_TARGET; 1655 data->cur_target->sync_flag |= SDTR_DONE; 1656 } 1657 1658 /* 1659 * It is always ensured by SCSI standard that initiator 1660 * switches into Bus Free Phase after 1661 * receiving message 00 (Command Complete), 04 (Disconnect). 1662 * It's the reason that processing here is valid. 1663 */ 1664 if (execph & MSGIN_00_VALID) { 1665 /* MsgIn 00: Command Complete */ 1666 nsp32_dbg(NSP32_DEBUG_BUSFREE, "command complete"); 1667 1668 SCpnt->SCp.Status = nsp32_read1(base, SCSI_CSB_IN); 1669 SCpnt->SCp.Message = 0; 1670 nsp32_dbg(NSP32_DEBUG_BUSFREE, 1671 "normal end stat=0x%x resid=0x%x\n", 1672 SCpnt->SCp.Status, scsi_get_resid(SCpnt)); 1673 SCpnt->result = (DID_OK << 16) | 1674 (SCpnt->SCp.Message << 8) | 1675 (SCpnt->SCp.Status << 0); 1676 nsp32_scsi_done(SCpnt); 1677 /* All operation is done */ 1678 return TRUE; 1679 } else if (execph & MSGIN_04_VALID) { 1680 /* MsgIn 04: Disconnect */ 1681 SCpnt->SCp.Status = nsp32_read1(base, SCSI_CSB_IN); 1682 SCpnt->SCp.Message = 4; 1683 1684 nsp32_dbg(NSP32_DEBUG_BUSFREE, "disconnect"); 1685 return TRUE; 1686 } else { 1687 /* Unexpected bus free */ 1688 nsp32_msg(KERN_WARNING, "unexpected bus free occurred"); 1689 1690 /* DID_ERROR? */ 1691 //SCpnt->result = (DID_OK << 16) | (SCpnt->SCp.Message << 8) | (SCpnt->SCp.Status << 0); 1692 SCpnt->result = DID_ERROR << 16; 1693 nsp32_scsi_done(SCpnt); 1694 return TRUE; 1695 } 1696 return FALSE; 1697 } 1698 1699 1700 /* 1701 * nsp32_adjust_busfree - adjusting SG table 1702 * 1703 * Note: This driver adjust the SG table using SCSI ACK 1704 * counter instead of BMCNT counter! 1705 */ 1706 static void nsp32_adjust_busfree(struct scsi_cmnd *SCpnt, unsigned int s_sacklen) 1707 { 1708 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 1709 int old_entry = data->cur_entry; 1710 int new_entry; 1711 int sg_num = data->cur_lunt->sg_num; 1712 nsp32_sgtable *sgt = data->cur_lunt->sglun->sgt; 1713 unsigned int restlen, sentlen; 1714 u32_le len, addr; 1715 1716 nsp32_dbg(NSP32_DEBUG_SGLIST, "old resid=0x%x", scsi_get_resid(SCpnt)); 1717 1718 /* adjust saved SACK count with 4 byte start address boundary */ 1719 s_sacklen -= le32_to_cpu(sgt[old_entry].addr) & 3; 1720 1721 /* 1722 * calculate new_entry from sack count and each sgt[].len 1723 * calculate the byte which is intent to send 1724 */ 1725 sentlen = 0; 1726 for (new_entry = old_entry; new_entry < sg_num; new_entry++) { 1727 sentlen += (le32_to_cpu(sgt[new_entry].len) & ~SGTEND); 1728 if (sentlen > s_sacklen) { 1729 break; 1730 } 1731 } 1732 1733 /* all sgt is processed */ 1734 if (new_entry == sg_num) { 1735 goto last; 1736 } 1737 1738 if (sentlen == s_sacklen) { 1739 /* XXX: confirm it's ok or not */ 1740 /* In this case, it's ok because we are at 1741 the head element of the sg. restlen is correctly calculated. */ 1742 } 1743 1744 /* calculate the rest length for transferring */ 1745 restlen = sentlen - s_sacklen; 1746 1747 /* update adjusting current SG table entry */ 1748 len = le32_to_cpu(sgt[new_entry].len); 1749 addr = le32_to_cpu(sgt[new_entry].addr); 1750 addr += (len - restlen); 1751 sgt[new_entry].addr = cpu_to_le32(addr); 1752 sgt[new_entry].len = cpu_to_le32(restlen); 1753 1754 /* set cur_entry with new_entry */ 1755 data->cur_entry = new_entry; 1756 1757 return; 1758 1759 last: 1760 if (scsi_get_resid(SCpnt) < sentlen) { 1761 nsp32_msg(KERN_ERR, "resid underflow"); 1762 } 1763 1764 scsi_set_resid(SCpnt, scsi_get_resid(SCpnt) - sentlen); 1765 nsp32_dbg(NSP32_DEBUG_SGLIST, "new resid=0x%x", scsi_get_resid(SCpnt)); 1766 1767 /* update hostdata and lun */ 1768 1769 return; 1770 } 1771 1772 1773 /* 1774 * It's called MsgOut phase occur. 1775 * NinjaSCSI-32Bi/UDE automatically processes up to 3 messages in 1776 * message out phase. It, however, has more than 3 messages, 1777 * HBA creates the interrupt and we have to process by hand. 1778 */ 1779 static void nsp32_msgout_occur(struct scsi_cmnd *SCpnt) 1780 { 1781 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 1782 unsigned int base = SCpnt->device->host->io_port; 1783 //unsigned short command; 1784 long new_sgtp; 1785 int i; 1786 1787 nsp32_dbg(NSP32_DEBUG_MSGOUTOCCUR, 1788 "enter: msgout_len: 0x%x", data->msgout_len); 1789 1790 /* 1791 * If MsgOut phase is occurred without having any 1792 * message, then No_Operation is sent (SCSI-2). 1793 */ 1794 if (data->msgout_len == 0) { 1795 nsp32_build_nop(SCpnt); 1796 } 1797 1798 /* 1799 * Set SGTP ADDR current entry for restarting AUTOSCSI, 1800 * because SGTP is incremented next point. 1801 * There is few statement in the specification... 1802 */ 1803 new_sgtp = data->cur_lunt->sglun_paddr + 1804 (data->cur_lunt->cur_entry * sizeof(nsp32_sgtable)); 1805 1806 /* 1807 * send messages 1808 */ 1809 for (i = 0; i < data->msgout_len; i++) { 1810 nsp32_dbg(NSP32_DEBUG_MSGOUTOCCUR, 1811 "%d : 0x%x", i, data->msgoutbuf[i]); 1812 1813 /* 1814 * Check REQ is asserted. 1815 */ 1816 nsp32_wait_req(data, ASSERT); 1817 1818 if (i == (data->msgout_len - 1)) { 1819 /* 1820 * If the last message, set the AutoSCSI restart 1821 * before send back the ack message. AutoSCSI 1822 * restart automatically negate ATN signal. 1823 */ 1824 //command = (AUTO_MSGIN_00_OR_04 | AUTO_MSGIN_02); 1825 //nsp32_restart_autoscsi(SCpnt, command); 1826 nsp32_write2(base, COMMAND_CONTROL, 1827 (CLEAR_CDB_FIFO_POINTER | 1828 AUTO_COMMAND_PHASE | 1829 AUTOSCSI_RESTART | 1830 AUTO_MSGIN_00_OR_04 | 1831 AUTO_MSGIN_02 )); 1832 } 1833 /* 1834 * Write data with SACK, then wait sack is 1835 * automatically negated. 1836 */ 1837 nsp32_write1(base, SCSI_DATA_WITH_ACK, data->msgoutbuf[i]); 1838 nsp32_wait_sack(data, NEGATE); 1839 1840 nsp32_dbg(NSP32_DEBUG_MSGOUTOCCUR, "bus: 0x%x\n", 1841 nsp32_read1(base, SCSI_BUS_MONITOR)); 1842 } 1843 1844 data->msgout_len = 0; 1845 1846 nsp32_dbg(NSP32_DEBUG_MSGOUTOCCUR, "exit"); 1847 } 1848 1849 /* 1850 * Restart AutoSCSI 1851 * 1852 * Note: Restarting AutoSCSI needs set: 1853 * SYNC_REG, ACK_WIDTH, SGT_ADR, TRANSFER_CONTROL 1854 */ 1855 static void nsp32_restart_autoscsi(struct scsi_cmnd *SCpnt, unsigned short command) 1856 { 1857 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 1858 unsigned int base = data->BaseAddress; 1859 unsigned short transfer = 0; 1860 1861 nsp32_dbg(NSP32_DEBUG_RESTART, "enter"); 1862 1863 if (data->cur_target == NULL || data->cur_lunt == NULL) { 1864 nsp32_msg(KERN_ERR, "Target or Lun is invalid"); 1865 } 1866 1867 /* 1868 * set SYNC_REG 1869 * Don't set BM_START_ADR before setting this register. 1870 */ 1871 nsp32_write1(base, SYNC_REG, data->cur_target->syncreg); 1872 1873 /* 1874 * set ACKWIDTH 1875 */ 1876 nsp32_write1(base, ACK_WIDTH, data->cur_target->ackwidth); 1877 1878 /* 1879 * set SREQ hazard killer sampling rate 1880 */ 1881 nsp32_write1(base, SREQ_SMPL_RATE, data->cur_target->sample_reg); 1882 1883 /* 1884 * set SGT ADDR (physical address) 1885 */ 1886 nsp32_write4(base, SGT_ADR, data->cur_lunt->sglun_paddr); 1887 1888 /* 1889 * set TRANSFER CONTROL REG 1890 */ 1891 transfer = 0; 1892 transfer |= (TRANSFER_GO | ALL_COUNTER_CLR); 1893 if (data->trans_method & NSP32_TRANSFER_BUSMASTER) { 1894 if (scsi_bufflen(SCpnt) > 0) { 1895 transfer |= BM_START; 1896 } 1897 } else if (data->trans_method & NSP32_TRANSFER_MMIO) { 1898 transfer |= CB_MMIO_MODE; 1899 } else if (data->trans_method & NSP32_TRANSFER_PIO) { 1900 transfer |= CB_IO_MODE; 1901 } 1902 nsp32_write2(base, TRANSFER_CONTROL, transfer); 1903 1904 /* 1905 * restart AutoSCSI 1906 * 1907 * TODO: COMMANDCONTROL_AUTO_COMMAND_PHASE is needed ? 1908 */ 1909 command |= (CLEAR_CDB_FIFO_POINTER | 1910 AUTO_COMMAND_PHASE | 1911 AUTOSCSI_RESTART ); 1912 nsp32_write2(base, COMMAND_CONTROL, command); 1913 1914 nsp32_dbg(NSP32_DEBUG_RESTART, "exit"); 1915 } 1916 1917 1918 /* 1919 * cannot run automatically message in occur 1920 */ 1921 static void nsp32_msgin_occur(struct scsi_cmnd *SCpnt, 1922 unsigned long irq_status, 1923 unsigned short execph) 1924 { 1925 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 1926 unsigned int base = SCpnt->device->host->io_port; 1927 unsigned char msg; 1928 unsigned char msgtype; 1929 unsigned char newlun; 1930 unsigned short command = 0; 1931 int msgclear = TRUE; 1932 long new_sgtp; 1933 int ret; 1934 1935 /* 1936 * read first message 1937 * Use SCSIDATA_W_ACK instead of SCSIDATAIN, because the procedure 1938 * of Message-In have to be processed before sending back SCSI ACK. 1939 */ 1940 msg = nsp32_read1(base, SCSI_DATA_IN); 1941 data->msginbuf[(unsigned char)data->msgin_len] = msg; 1942 msgtype = data->msginbuf[0]; 1943 nsp32_dbg(NSP32_DEBUG_MSGINOCCUR, 1944 "enter: msglen: 0x%x msgin: 0x%x msgtype: 0x%x", 1945 data->msgin_len, msg, msgtype); 1946 1947 /* 1948 * TODO: We need checking whether bus phase is message in? 1949 */ 1950 1951 /* 1952 * assert SCSI ACK 1953 */ 1954 nsp32_sack_assert(data); 1955 1956 /* 1957 * processing IDENTIFY 1958 */ 1959 if (msgtype & 0x80) { 1960 if (!(irq_status & IRQSTATUS_RESELECT_OCCUER)) { 1961 /* Invalid (non reselect) phase */ 1962 goto reject; 1963 } 1964 1965 newlun = msgtype & 0x1f; /* TODO: SPI-3 compliant? */ 1966 ret = nsp32_reselection(SCpnt, newlun); 1967 if (ret == TRUE) { 1968 goto restart; 1969 } else { 1970 goto reject; 1971 } 1972 } 1973 1974 /* 1975 * processing messages except for IDENTIFY 1976 * 1977 * TODO: Messages are all SCSI-2 terminology. SCSI-3 compliance is TODO. 1978 */ 1979 switch (msgtype) { 1980 /* 1981 * 1-byte message 1982 */ 1983 case COMMAND_COMPLETE: 1984 case DISCONNECT: 1985 /* 1986 * These messages should not be occurred. 1987 * They should be processed on AutoSCSI sequencer. 1988 */ 1989 nsp32_msg(KERN_WARNING, 1990 "unexpected message of AutoSCSI MsgIn: 0x%x", msg); 1991 break; 1992 1993 case RESTORE_POINTERS: 1994 /* 1995 * AutoMsgIn03 is disabled, and HBA gets this message. 1996 */ 1997 1998 if ((execph & DATA_IN_PHASE) || (execph & DATA_OUT_PHASE)) { 1999 unsigned int s_sacklen; 2000 2001 s_sacklen = nsp32_read4(base, SAVED_SACK_CNT); 2002 if ((execph & MSGIN_02_VALID) && (s_sacklen > 0)) { 2003 nsp32_adjust_busfree(SCpnt, s_sacklen); 2004 } else { 2005 /* No need to rewrite SGT */ 2006 } 2007 } 2008 data->cur_lunt->msgin03 = FALSE; 2009 2010 /* Update with the new value */ 2011 2012 /* reset SACK/SavedACK counter (or ALL clear?) */ 2013 nsp32_write4(base, CLR_COUNTER, CLRCOUNTER_ALLMASK); 2014 2015 /* 2016 * set new sg pointer 2017 */ 2018 new_sgtp = data->cur_lunt->sglun_paddr + 2019 (data->cur_lunt->cur_entry * sizeof(nsp32_sgtable)); 2020 nsp32_write4(base, SGT_ADR, new_sgtp); 2021 2022 break; 2023 2024 case SAVE_POINTERS: 2025 /* 2026 * These messages should not be occurred. 2027 * They should be processed on AutoSCSI sequencer. 2028 */ 2029 nsp32_msg (KERN_WARNING, 2030 "unexpected message of AutoSCSI MsgIn: SAVE_POINTERS"); 2031 2032 break; 2033 2034 case MESSAGE_REJECT: 2035 /* If previous message_out is sending SDTR, and get 2036 message_reject from target, SDTR negotiation is failed */ 2037 if (data->cur_target->sync_flag & 2038 (SDTR_INITIATOR | SDTR_TARGET)) { 2039 /* 2040 * Current target is negotiating SDTR, but it's 2041 * failed. Fall back to async transfer mode, and set 2042 * SDTR_DONE. 2043 */ 2044 nsp32_set_async(data, data->cur_target); 2045 data->cur_target->sync_flag &= ~SDTR_INITIATOR; 2046 data->cur_target->sync_flag |= SDTR_DONE; 2047 2048 } 2049 break; 2050 2051 case LINKED_CMD_COMPLETE: 2052 case LINKED_FLG_CMD_COMPLETE: 2053 /* queue tag is not supported currently */ 2054 nsp32_msg (KERN_WARNING, 2055 "unsupported message: 0x%x", msgtype); 2056 break; 2057 2058 case INITIATE_RECOVERY: 2059 /* staring ECA (Extended Contingent Allegiance) state. */ 2060 /* This message is declined in SPI2 or later. */ 2061 2062 goto reject; 2063 2064 /* 2065 * 2-byte message 2066 */ 2067 case SIMPLE_QUEUE_TAG: 2068 case 0x23: 2069 /* 2070 * 0x23: Ignore_Wide_Residue is not declared in scsi.h. 2071 * No support is needed. 2072 */ 2073 if (data->msgin_len >= 1) { 2074 goto reject; 2075 } 2076 2077 /* current position is 1-byte of 2 byte */ 2078 msgclear = FALSE; 2079 2080 break; 2081 2082 /* 2083 * extended message 2084 */ 2085 case EXTENDED_MESSAGE: 2086 if (data->msgin_len < 1) { 2087 /* 2088 * Current position does not reach 2-byte 2089 * (2-byte is extended message length). 2090 */ 2091 msgclear = FALSE; 2092 break; 2093 } 2094 2095 if ((data->msginbuf[1] + 1) > data->msgin_len) { 2096 /* 2097 * Current extended message has msginbuf[1] + 2 2098 * (msgin_len starts counting from 0, so buf[1] + 1). 2099 * If current message position is not finished, 2100 * continue receiving message. 2101 */ 2102 msgclear = FALSE; 2103 break; 2104 } 2105 2106 /* 2107 * Reach here means regular length of each type of 2108 * extended messages. 2109 */ 2110 switch (data->msginbuf[2]) { 2111 case EXTENDED_MODIFY_DATA_POINTER: 2112 /* TODO */ 2113 goto reject; /* not implemented yet */ 2114 break; 2115 2116 case EXTENDED_SDTR: 2117 /* 2118 * Exchange this message between initiator and target. 2119 */ 2120 if (data->msgin_len != EXTENDED_SDTR_LEN + 1) { 2121 /* 2122 * received inappropriate message. 2123 */ 2124 goto reject; 2125 break; 2126 } 2127 2128 nsp32_analyze_sdtr(SCpnt); 2129 2130 break; 2131 2132 case EXTENDED_EXTENDED_IDENTIFY: 2133 /* SCSI-I only, not supported. */ 2134 goto reject; /* not implemented yet */ 2135 2136 break; 2137 2138 case EXTENDED_WDTR: 2139 goto reject; /* not implemented yet */ 2140 2141 break; 2142 2143 default: 2144 goto reject; 2145 } 2146 break; 2147 2148 default: 2149 goto reject; 2150 } 2151 2152 restart: 2153 if (msgclear == TRUE) { 2154 data->msgin_len = 0; 2155 2156 /* 2157 * If restarting AutoSCSI, but there are some message to out 2158 * (msgout_len > 0), set AutoATN, and set SCSIMSGOUT as 0 2159 * (MV_VALID = 0). When commandcontrol is written with 2160 * AutoSCSI restart, at the same time MsgOutOccur should be 2161 * happened (however, such situation is really possible...?). 2162 */ 2163 if (data->msgout_len > 0) { 2164 nsp32_write4(base, SCSI_MSG_OUT, 0); 2165 command |= AUTO_ATN; 2166 } 2167 2168 /* 2169 * restart AutoSCSI 2170 * If it's failed, COMMANDCONTROL_AUTO_COMMAND_PHASE is needed. 2171 */ 2172 command |= (AUTO_MSGIN_00_OR_04 | AUTO_MSGIN_02); 2173 2174 /* 2175 * If current msgin03 is TRUE, then flag on. 2176 */ 2177 if (data->cur_lunt->msgin03 == TRUE) { 2178 command |= AUTO_MSGIN_03; 2179 } 2180 data->cur_lunt->msgin03 = FALSE; 2181 } else { 2182 data->msgin_len++; 2183 } 2184 2185 /* 2186 * restart AutoSCSI 2187 */ 2188 nsp32_restart_autoscsi(SCpnt, command); 2189 2190 /* 2191 * wait SCSI REQ negate for REQ-ACK handshake 2192 */ 2193 nsp32_wait_req(data, NEGATE); 2194 2195 /* 2196 * negate SCSI ACK 2197 */ 2198 nsp32_sack_negate(data); 2199 2200 nsp32_dbg(NSP32_DEBUG_MSGINOCCUR, "exit"); 2201 2202 return; 2203 2204 reject: 2205 nsp32_msg(KERN_WARNING, 2206 "invalid or unsupported MessageIn, rejected. " 2207 "current msg: 0x%x (len: 0x%x), processing msg: 0x%x", 2208 msg, data->msgin_len, msgtype); 2209 nsp32_build_reject(SCpnt); 2210 data->msgin_len = 0; 2211 2212 goto restart; 2213 } 2214 2215 /* 2216 * 2217 */ 2218 static void nsp32_analyze_sdtr(struct scsi_cmnd *SCpnt) 2219 { 2220 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 2221 nsp32_target *target = data->cur_target; 2222 nsp32_sync_table *synct; 2223 unsigned char get_period = data->msginbuf[3]; 2224 unsigned char get_offset = data->msginbuf[4]; 2225 int entry; 2226 int syncnum; 2227 2228 nsp32_dbg(NSP32_DEBUG_MSGINOCCUR, "enter"); 2229 2230 synct = data->synct; 2231 syncnum = data->syncnum; 2232 2233 /* 2234 * If this inititor sent the SDTR message, then target responds SDTR, 2235 * initiator SYNCREG, ACKWIDTH from SDTR parameter. 2236 * Messages are not appropriate, then send back reject message. 2237 * If initiator did not send the SDTR, but target sends SDTR, 2238 * initiator calculator the appropriate parameter and send back SDTR. 2239 */ 2240 if (target->sync_flag & SDTR_INITIATOR) { 2241 /* 2242 * Initiator sent SDTR, the target responds and 2243 * send back negotiation SDTR. 2244 */ 2245 nsp32_dbg(NSP32_DEBUG_MSGINOCCUR, "target responds SDTR"); 2246 2247 target->sync_flag &= ~SDTR_INITIATOR; 2248 target->sync_flag |= SDTR_DONE; 2249 2250 /* 2251 * offset: 2252 */ 2253 if (get_offset > SYNC_OFFSET) { 2254 /* 2255 * Negotiation is failed, the target send back 2256 * unexpected offset value. 2257 */ 2258 goto reject; 2259 } 2260 2261 if (get_offset == ASYNC_OFFSET) { 2262 /* 2263 * Negotiation is succeeded, the target want 2264 * to fall back into asynchronous transfer mode. 2265 */ 2266 goto async; 2267 } 2268 2269 /* 2270 * period: 2271 * Check whether sync period is too short. If too short, 2272 * fall back to async mode. If it's ok, then investigate 2273 * the received sync period. If sync period is acceptable 2274 * between sync table start_period and end_period, then 2275 * set this I_T nexus as sent offset and period. 2276 * If it's not acceptable, send back reject and fall back 2277 * to async mode. 2278 */ 2279 if (get_period < data->synct[0].period_num) { 2280 /* 2281 * Negotiation is failed, the target send back 2282 * unexpected period value. 2283 */ 2284 goto reject; 2285 } 2286 2287 entry = nsp32_search_period_entry(data, target, get_period); 2288 2289 if (entry < 0) { 2290 /* 2291 * Target want to use long period which is not 2292 * acceptable NinjaSCSI-32Bi/UDE. 2293 */ 2294 goto reject; 2295 } 2296 2297 /* 2298 * Set new sync table and offset in this I_T nexus. 2299 */ 2300 nsp32_set_sync_entry(data, target, entry, get_offset); 2301 } else { 2302 /* Target send SDTR to initiator. */ 2303 nsp32_dbg(NSP32_DEBUG_MSGINOCCUR, "target send SDTR"); 2304 2305 target->sync_flag |= SDTR_INITIATOR; 2306 2307 /* offset: */ 2308 if (get_offset > SYNC_OFFSET) { 2309 /* send back as SYNC_OFFSET */ 2310 get_offset = SYNC_OFFSET; 2311 } 2312 2313 /* period: */ 2314 if (get_period < data->synct[0].period_num) { 2315 get_period = data->synct[0].period_num; 2316 } 2317 2318 entry = nsp32_search_period_entry(data, target, get_period); 2319 2320 if (get_offset == ASYNC_OFFSET || entry < 0) { 2321 nsp32_set_async(data, target); 2322 nsp32_build_sdtr(SCpnt, 0, ASYNC_OFFSET); 2323 } else { 2324 nsp32_set_sync_entry(data, target, entry, get_offset); 2325 nsp32_build_sdtr(SCpnt, get_period, get_offset); 2326 } 2327 } 2328 2329 target->period = get_period; 2330 nsp32_dbg(NSP32_DEBUG_MSGINOCCUR, "exit"); 2331 return; 2332 2333 reject: 2334 /* 2335 * If the current message is unacceptable, send back to the target 2336 * with reject message. 2337 */ 2338 nsp32_build_reject(SCpnt); 2339 2340 async: 2341 nsp32_set_async(data, target); /* set as ASYNC transfer mode */ 2342 2343 target->period = 0; 2344 nsp32_dbg(NSP32_DEBUG_MSGINOCCUR, "exit: set async"); 2345 return; 2346 } 2347 2348 2349 /* 2350 * Search config entry number matched in sync_table from given 2351 * target and speed period value. If failed to search, return negative value. 2352 */ 2353 static int nsp32_search_period_entry(nsp32_hw_data *data, 2354 nsp32_target *target, 2355 unsigned char period) 2356 { 2357 int i; 2358 2359 if (target->limit_entry >= data->syncnum) { 2360 nsp32_msg(KERN_ERR, "limit_entry exceeds syncnum!"); 2361 target->limit_entry = 0; 2362 } 2363 2364 for (i = target->limit_entry; i < data->syncnum; i++) { 2365 if (period >= data->synct[i].start_period && 2366 period <= data->synct[i].end_period) { 2367 break; 2368 } 2369 } 2370 2371 /* 2372 * Check given period value is over the sync_table value. 2373 * If so, return max value. 2374 */ 2375 if (i == data->syncnum) { 2376 i = -1; 2377 } 2378 2379 return i; 2380 } 2381 2382 2383 /* 2384 * target <-> initiator use ASYNC transfer 2385 */ 2386 static void nsp32_set_async(nsp32_hw_data *data, nsp32_target *target) 2387 { 2388 unsigned char period = data->synct[target->limit_entry].period_num; 2389 2390 target->offset = ASYNC_OFFSET; 2391 target->period = 0; 2392 target->syncreg = TO_SYNCREG(period, ASYNC_OFFSET); 2393 target->ackwidth = 0; 2394 target->sample_reg = 0; 2395 2396 nsp32_dbg(NSP32_DEBUG_SYNC, "set async"); 2397 } 2398 2399 2400 /* 2401 * target <-> initiator use maximum SYNC transfer 2402 */ 2403 static void nsp32_set_max_sync(nsp32_hw_data *data, 2404 nsp32_target *target, 2405 unsigned char *period, 2406 unsigned char *offset) 2407 { 2408 unsigned char period_num, ackwidth; 2409 2410 period_num = data->synct[target->limit_entry].period_num; 2411 *period = data->synct[target->limit_entry].start_period; 2412 ackwidth = data->synct[target->limit_entry].ackwidth; 2413 *offset = SYNC_OFFSET; 2414 2415 target->syncreg = TO_SYNCREG(period_num, *offset); 2416 target->ackwidth = ackwidth; 2417 target->offset = *offset; 2418 target->sample_reg = 0; /* disable SREQ sampling */ 2419 } 2420 2421 2422 /* 2423 * target <-> initiator use entry number speed 2424 */ 2425 static void nsp32_set_sync_entry(nsp32_hw_data *data, 2426 nsp32_target *target, 2427 int entry, 2428 unsigned char offset) 2429 { 2430 unsigned char period, ackwidth, sample_rate; 2431 2432 period = data->synct[entry].period_num; 2433 ackwidth = data->synct[entry].ackwidth; 2434 sample_rate = data->synct[entry].sample_rate; 2435 2436 target->syncreg = TO_SYNCREG(period, offset); 2437 target->ackwidth = ackwidth; 2438 target->offset = offset; 2439 target->sample_reg = sample_rate | SAMPLING_ENABLE; 2440 2441 nsp32_dbg(NSP32_DEBUG_SYNC, "set sync"); 2442 } 2443 2444 2445 /* 2446 * It waits until SCSI REQ becomes assertion or negation state. 2447 * 2448 * Note: If nsp32_msgin_occur is called, we asserts SCSI ACK. Then 2449 * connected target responds SCSI REQ negation. We have to wait 2450 * SCSI REQ becomes negation in order to negate SCSI ACK signal for 2451 * REQ-ACK handshake. 2452 */ 2453 static void nsp32_wait_req(nsp32_hw_data *data, int state) 2454 { 2455 unsigned int base = data->BaseAddress; 2456 int wait_time = 0; 2457 unsigned char bus, req_bit; 2458 2459 if (!((state == ASSERT) || (state == NEGATE))) { 2460 nsp32_msg(KERN_ERR, "unknown state designation"); 2461 } 2462 /* REQ is BIT(5) */ 2463 req_bit = (state == ASSERT ? BUSMON_REQ : 0); 2464 2465 do { 2466 bus = nsp32_read1(base, SCSI_BUS_MONITOR); 2467 if ((bus & BUSMON_REQ) == req_bit) { 2468 nsp32_dbg(NSP32_DEBUG_WAIT, 2469 "wait_time: %d", wait_time); 2470 return; 2471 } 2472 udelay(1); 2473 wait_time++; 2474 } while (wait_time < REQSACK_TIMEOUT_TIME); 2475 2476 nsp32_msg(KERN_WARNING, "wait REQ timeout, req_bit: 0x%x", req_bit); 2477 } 2478 2479 /* 2480 * It waits until SCSI SACK becomes assertion or negation state. 2481 */ 2482 static void nsp32_wait_sack(nsp32_hw_data *data, int state) 2483 { 2484 unsigned int base = data->BaseAddress; 2485 int wait_time = 0; 2486 unsigned char bus, ack_bit; 2487 2488 if (!((state == ASSERT) || (state == NEGATE))) { 2489 nsp32_msg(KERN_ERR, "unknown state designation"); 2490 } 2491 /* ACK is BIT(4) */ 2492 ack_bit = (state == ASSERT ? BUSMON_ACK : 0); 2493 2494 do { 2495 bus = nsp32_read1(base, SCSI_BUS_MONITOR); 2496 if ((bus & BUSMON_ACK) == ack_bit) { 2497 nsp32_dbg(NSP32_DEBUG_WAIT, 2498 "wait_time: %d", wait_time); 2499 return; 2500 } 2501 udelay(1); 2502 wait_time++; 2503 } while (wait_time < REQSACK_TIMEOUT_TIME); 2504 2505 nsp32_msg(KERN_WARNING, "wait SACK timeout, ack_bit: 0x%x", ack_bit); 2506 } 2507 2508 /* 2509 * assert SCSI ACK 2510 * 2511 * Note: SCSI ACK assertion needs with ACKENB=1, AUTODIRECTION=1. 2512 */ 2513 static void nsp32_sack_assert(nsp32_hw_data *data) 2514 { 2515 unsigned int base = data->BaseAddress; 2516 unsigned char busctrl; 2517 2518 busctrl = nsp32_read1(base, SCSI_BUS_CONTROL); 2519 busctrl |= (BUSCTL_ACK | AUTODIRECTION | ACKENB); 2520 nsp32_write1(base, SCSI_BUS_CONTROL, busctrl); 2521 } 2522 2523 /* 2524 * negate SCSI ACK 2525 */ 2526 static void nsp32_sack_negate(nsp32_hw_data *data) 2527 { 2528 unsigned int base = data->BaseAddress; 2529 unsigned char busctrl; 2530 2531 busctrl = nsp32_read1(base, SCSI_BUS_CONTROL); 2532 busctrl &= ~BUSCTL_ACK; 2533 nsp32_write1(base, SCSI_BUS_CONTROL, busctrl); 2534 } 2535 2536 2537 2538 /* 2539 * Note: n_io_port is defined as 0x7f because I/O register port is 2540 * assigned as: 2541 * 0x800-0x8ff: memory mapped I/O port 2542 * 0x900-0xbff: (map same 0x800-0x8ff I/O port image repeatedly) 2543 * 0xc00-0xfff: CardBus status registers 2544 */ 2545 static int nsp32_detect(struct pci_dev *pdev) 2546 { 2547 struct Scsi_Host *host; /* registered host structure */ 2548 struct resource *res; 2549 nsp32_hw_data *data; 2550 int ret; 2551 int i, j; 2552 2553 nsp32_dbg(NSP32_DEBUG_REGISTER, "enter"); 2554 2555 /* 2556 * register this HBA as SCSI device 2557 */ 2558 host = scsi_host_alloc(&nsp32_template, sizeof(nsp32_hw_data)); 2559 if (host == NULL) { 2560 nsp32_msg (KERN_ERR, "failed to scsi register"); 2561 goto err; 2562 } 2563 2564 /* 2565 * set nsp32_hw_data 2566 */ 2567 data = (nsp32_hw_data *)host->hostdata; 2568 2569 memcpy(data, &nsp32_data_base, sizeof(nsp32_hw_data)); 2570 2571 host->irq = data->IrqNumber; 2572 host->io_port = data->BaseAddress; 2573 host->unique_id = data->BaseAddress; 2574 host->n_io_port = data->NumAddress; 2575 host->base = (unsigned long)data->MmioAddress; 2576 2577 data->Host = host; 2578 spin_lock_init(&(data->Lock)); 2579 2580 data->cur_lunt = NULL; 2581 data->cur_target = NULL; 2582 2583 /* 2584 * Bus master transfer mode is supported currently. 2585 */ 2586 data->trans_method = NSP32_TRANSFER_BUSMASTER; 2587 2588 /* 2589 * Set clock div, CLOCK_4 (HBA has own external clock, and 2590 * dividing * 100ns/4). 2591 * Currently CLOCK_4 has only tested, not for CLOCK_2/PCICLK yet. 2592 */ 2593 data->clock = CLOCK_4; 2594 2595 /* 2596 * Select appropriate nsp32_sync_table and set I_CLOCKDIV. 2597 */ 2598 switch (data->clock) { 2599 case CLOCK_4: 2600 /* If data->clock is CLOCK_4, then select 40M sync table. */ 2601 data->synct = nsp32_sync_table_40M; 2602 data->syncnum = ARRAY_SIZE(nsp32_sync_table_40M); 2603 break; 2604 case CLOCK_2: 2605 /* If data->clock is CLOCK_2, then select 20M sync table. */ 2606 data->synct = nsp32_sync_table_20M; 2607 data->syncnum = ARRAY_SIZE(nsp32_sync_table_20M); 2608 break; 2609 case PCICLK: 2610 /* If data->clock is PCICLK, then select pci sync table. */ 2611 data->synct = nsp32_sync_table_pci; 2612 data->syncnum = ARRAY_SIZE(nsp32_sync_table_pci); 2613 break; 2614 default: 2615 nsp32_msg(KERN_WARNING, 2616 "Invalid clock div is selected, set CLOCK_4."); 2617 /* Use default value CLOCK_4 */ 2618 data->clock = CLOCK_4; 2619 data->synct = nsp32_sync_table_40M; 2620 data->syncnum = ARRAY_SIZE(nsp32_sync_table_40M); 2621 } 2622 2623 /* 2624 * setup nsp32_lunt 2625 */ 2626 2627 /* 2628 * setup DMA 2629 */ 2630 if (dma_set_mask(&pdev->dev, DMA_BIT_MASK(32)) != 0) { 2631 nsp32_msg (KERN_ERR, "failed to set PCI DMA mask"); 2632 goto scsi_unregister; 2633 } 2634 2635 /* 2636 * allocate autoparam DMA resource. 2637 */ 2638 data->autoparam = dma_alloc_coherent(&pdev->dev, 2639 sizeof(nsp32_autoparam), &(data->auto_paddr), 2640 GFP_KERNEL); 2641 if (data->autoparam == NULL) { 2642 nsp32_msg(KERN_ERR, "failed to allocate DMA memory"); 2643 goto scsi_unregister; 2644 } 2645 2646 /* 2647 * allocate scatter-gather DMA resource. 2648 */ 2649 data->sg_list = dma_alloc_coherent(&pdev->dev, NSP32_SG_TABLE_SIZE, 2650 &data->sg_paddr, GFP_KERNEL); 2651 if (data->sg_list == NULL) { 2652 nsp32_msg(KERN_ERR, "failed to allocate DMA memory"); 2653 goto free_autoparam; 2654 } 2655 2656 for (i = 0; i < ARRAY_SIZE(data->lunt); i++) { 2657 for (j = 0; j < ARRAY_SIZE(data->lunt[0]); j++) { 2658 int offset = i * ARRAY_SIZE(data->lunt[0]) + j; 2659 nsp32_lunt tmp = { 2660 .SCpnt = NULL, 2661 .save_datp = 0, 2662 .msgin03 = FALSE, 2663 .sg_num = 0, 2664 .cur_entry = 0, 2665 .sglun = &(data->sg_list[offset]), 2666 .sglun_paddr = data->sg_paddr + (offset * sizeof(nsp32_sglun)), 2667 }; 2668 2669 data->lunt[i][j] = tmp; 2670 } 2671 } 2672 2673 /* 2674 * setup target 2675 */ 2676 for (i = 0; i < ARRAY_SIZE(data->target); i++) { 2677 nsp32_target *target = &(data->target[i]); 2678 2679 target->limit_entry = 0; 2680 target->sync_flag = 0; 2681 nsp32_set_async(data, target); 2682 } 2683 2684 /* 2685 * EEPROM check 2686 */ 2687 ret = nsp32_getprom_param(data); 2688 if (ret == FALSE) { 2689 data->resettime = 3; /* default 3 */ 2690 } 2691 2692 /* 2693 * setup HBA 2694 */ 2695 nsp32hw_init(data); 2696 2697 snprintf(data->info_str, sizeof(data->info_str), 2698 "NinjaSCSI-32Bi/UDE: irq %d, io 0x%lx+0x%x", 2699 host->irq, host->io_port, host->n_io_port); 2700 2701 /* 2702 * SCSI bus reset 2703 * 2704 * Note: It's important to reset SCSI bus in initialization phase. 2705 * NinjaSCSI-32Bi/UDE HBA EEPROM seems to exchange SDTR when 2706 * system is coming up, so SCSI devices connected to HBA is set as 2707 * un-asynchronous mode. It brings the merit that this HBA is 2708 * ready to start synchronous transfer without any preparation, 2709 * but we are difficult to control transfer speed. In addition, 2710 * it prevents device transfer speed from effecting EEPROM start-up 2711 * SDTR. NinjaSCSI-32Bi/UDE has the feature if EEPROM is set as 2712 * Auto Mode, then FAST-10M is selected when SCSI devices are 2713 * connected same or more than 4 devices. It should be avoided 2714 * depending on this specification. Thus, resetting the SCSI bus 2715 * restores all connected SCSI devices to asynchronous mode, then 2716 * this driver set SDTR safely later, and we can control all SCSI 2717 * device transfer mode. 2718 */ 2719 nsp32_do_bus_reset(data); 2720 2721 ret = request_irq(host->irq, do_nsp32_isr, IRQF_SHARED, "nsp32", data); 2722 if (ret < 0) { 2723 nsp32_msg(KERN_ERR, "Unable to allocate IRQ for NinjaSCSI32 " 2724 "SCSI PCI controller. Interrupt: %d", host->irq); 2725 goto free_sg_list; 2726 } 2727 2728 /* 2729 * PCI IO register 2730 */ 2731 res = request_region(host->io_port, host->n_io_port, "nsp32"); 2732 if (res == NULL) { 2733 nsp32_msg(KERN_ERR, 2734 "I/O region 0x%lx+0x%lx is already used", 2735 data->BaseAddress, data->NumAddress); 2736 goto free_irq; 2737 } 2738 2739 ret = scsi_add_host(host, &pdev->dev); 2740 if (ret) { 2741 nsp32_msg(KERN_ERR, "failed to add scsi host"); 2742 goto free_region; 2743 } 2744 scsi_scan_host(host); 2745 pci_set_drvdata(pdev, host); 2746 return 0; 2747 2748 free_region: 2749 release_region(host->io_port, host->n_io_port); 2750 2751 free_irq: 2752 free_irq(host->irq, data); 2753 2754 free_sg_list: 2755 dma_free_coherent(&pdev->dev, NSP32_SG_TABLE_SIZE, 2756 data->sg_list, data->sg_paddr); 2757 2758 free_autoparam: 2759 dma_free_coherent(&pdev->dev, sizeof(nsp32_autoparam), 2760 data->autoparam, data->auto_paddr); 2761 2762 scsi_unregister: 2763 scsi_host_put(host); 2764 2765 err: 2766 return 1; 2767 } 2768 2769 static int nsp32_release(struct Scsi_Host *host) 2770 { 2771 nsp32_hw_data *data = (nsp32_hw_data *)host->hostdata; 2772 2773 if (data->autoparam) { 2774 dma_free_coherent(&data->Pci->dev, sizeof(nsp32_autoparam), 2775 data->autoparam, data->auto_paddr); 2776 } 2777 2778 if (data->sg_list) { 2779 dma_free_coherent(&data->Pci->dev, NSP32_SG_TABLE_SIZE, 2780 data->sg_list, data->sg_paddr); 2781 } 2782 2783 if (host->irq) { 2784 free_irq(host->irq, data); 2785 } 2786 2787 if (host->io_port && host->n_io_port) { 2788 release_region(host->io_port, host->n_io_port); 2789 } 2790 2791 if (data->MmioAddress) { 2792 iounmap(data->MmioAddress); 2793 } 2794 2795 return 0; 2796 } 2797 2798 static const char *nsp32_info(struct Scsi_Host *shpnt) 2799 { 2800 nsp32_hw_data *data = (nsp32_hw_data *)shpnt->hostdata; 2801 2802 return data->info_str; 2803 } 2804 2805 2806 /**************************************************************************** 2807 * error handler 2808 */ 2809 static int nsp32_eh_abort(struct scsi_cmnd *SCpnt) 2810 { 2811 nsp32_hw_data *data = (nsp32_hw_data *)SCpnt->device->host->hostdata; 2812 unsigned int base = SCpnt->device->host->io_port; 2813 2814 nsp32_msg(KERN_WARNING, "abort"); 2815 2816 if (data->cur_lunt->SCpnt == NULL) { 2817 nsp32_dbg(NSP32_DEBUG_BUSRESET, "abort failed"); 2818 return FAILED; 2819 } 2820 2821 if (data->cur_target->sync_flag & (SDTR_INITIATOR | SDTR_TARGET)) { 2822 /* reset SDTR negotiation */ 2823 data->cur_target->sync_flag = 0; 2824 nsp32_set_async(data, data->cur_target); 2825 } 2826 2827 nsp32_write2(base, TRANSFER_CONTROL, 0); 2828 nsp32_write2(base, BM_CNT, 0); 2829 2830 SCpnt->result = DID_ABORT << 16; 2831 nsp32_scsi_done(SCpnt); 2832 2833 nsp32_dbg(NSP32_DEBUG_BUSRESET, "abort success"); 2834 return SUCCESS; 2835 } 2836 2837 static void nsp32_do_bus_reset(nsp32_hw_data *data) 2838 { 2839 unsigned int base = data->BaseAddress; 2840 unsigned short intrdat; 2841 int i; 2842 2843 nsp32_dbg(NSP32_DEBUG_BUSRESET, "in"); 2844 2845 /* 2846 * stop all transfer 2847 * clear TRANSFERCONTROL_BM_START 2848 * clear counter 2849 */ 2850 nsp32_write2(base, TRANSFER_CONTROL, 0); 2851 nsp32_write4(base, BM_CNT, 0); 2852 nsp32_write4(base, CLR_COUNTER, CLRCOUNTER_ALLMASK); 2853 2854 /* 2855 * fall back to asynchronous transfer mode 2856 * initialize SDTR negotiation flag 2857 */ 2858 for (i = 0; i < ARRAY_SIZE(data->target); i++) { 2859 nsp32_target *target = &data->target[i]; 2860 2861 target->sync_flag = 0; 2862 nsp32_set_async(data, target); 2863 } 2864 2865 /* 2866 * reset SCSI bus 2867 */ 2868 nsp32_write1(base, SCSI_BUS_CONTROL, BUSCTL_RST); 2869 mdelay(RESET_HOLD_TIME / 1000); 2870 nsp32_write1(base, SCSI_BUS_CONTROL, 0); 2871 for(i = 0; i < 5; i++) { 2872 intrdat = nsp32_read2(base, IRQ_STATUS); /* dummy read */ 2873 nsp32_dbg(NSP32_DEBUG_BUSRESET, "irq:1: 0x%x", intrdat); 2874 } 2875 2876 data->CurrentSC = NULL; 2877 } 2878 2879 static int nsp32_eh_host_reset(struct scsi_cmnd *SCpnt) 2880 { 2881 struct Scsi_Host *host = SCpnt->device->host; 2882 unsigned int base = SCpnt->device->host->io_port; 2883 nsp32_hw_data *data = (nsp32_hw_data *)host->hostdata; 2884 2885 nsp32_msg(KERN_INFO, "Host Reset"); 2886 nsp32_dbg(NSP32_DEBUG_BUSRESET, "SCpnt=0x%x", SCpnt); 2887 2888 spin_lock_irq(SCpnt->device->host->host_lock); 2889 2890 nsp32hw_init(data); 2891 nsp32_write2(base, IRQ_CONTROL, IRQ_CONTROL_ALL_IRQ_MASK); 2892 nsp32_do_bus_reset(data); 2893 nsp32_write2(base, IRQ_CONTROL, 0); 2894 2895 spin_unlock_irq(SCpnt->device->host->host_lock); 2896 return SUCCESS; /* Host reset is succeeded at any time. */ 2897 } 2898 2899 2900 /************************************************************************** 2901 * EEPROM handler 2902 */ 2903 2904 /* 2905 * getting EEPROM parameter 2906 */ 2907 static int nsp32_getprom_param(nsp32_hw_data *data) 2908 { 2909 int vendor = data->pci_devid->vendor; 2910 int device = data->pci_devid->device; 2911 int ret, val, i; 2912 2913 /* 2914 * EEPROM checking. 2915 */ 2916 ret = nsp32_prom_read(data, 0x7e); 2917 if (ret != 0x55) { 2918 nsp32_msg(KERN_INFO, "No EEPROM detected: 0x%x", ret); 2919 return FALSE; 2920 } 2921 ret = nsp32_prom_read(data, 0x7f); 2922 if (ret != 0xaa) { 2923 nsp32_msg(KERN_INFO, "Invalid number: 0x%x", ret); 2924 return FALSE; 2925 } 2926 2927 /* 2928 * check EEPROM type 2929 */ 2930 if (vendor == PCI_VENDOR_ID_WORKBIT && 2931 device == PCI_DEVICE_ID_WORKBIT_STANDARD) { 2932 ret = nsp32_getprom_c16(data); 2933 } else if (vendor == PCI_VENDOR_ID_WORKBIT && 2934 device == PCI_DEVICE_ID_NINJASCSI_32BIB_LOGITEC) { 2935 ret = nsp32_getprom_at24(data); 2936 } else if (vendor == PCI_VENDOR_ID_WORKBIT && 2937 device == PCI_DEVICE_ID_NINJASCSI_32UDE_MELCO ) { 2938 ret = nsp32_getprom_at24(data); 2939 } else { 2940 nsp32_msg(KERN_WARNING, "Unknown EEPROM"); 2941 ret = FALSE; 2942 } 2943 2944 /* for debug : SPROM data full checking */ 2945 for (i = 0; i <= 0x1f; i++) { 2946 val = nsp32_prom_read(data, i); 2947 nsp32_dbg(NSP32_DEBUG_EEPROM, 2948 "rom address 0x%x : 0x%x", i, val); 2949 } 2950 2951 return ret; 2952 } 2953 2954 2955 /* 2956 * AT24C01A (Logitec: LHA-600S), AT24C02 (Melco Buffalo: IFC-USLP) data map: 2957 * 2958 * ROMADDR 2959 * 0x00 - 0x06 : Device Synchronous Transfer Period (SCSI ID 0 - 6) 2960 * Value 0x0: ASYNC, 0x0c: Ultra-20M, 0x19: Fast-10M 2961 * 0x07 : HBA Synchronous Transfer Period 2962 * Value 0: AutoSync, 1: Manual Setting 2963 * 0x08 - 0x0f : Not Used? (0x0) 2964 * 0x10 : Bus Termination 2965 * Value 0: Auto[ON], 1: ON, 2: OFF 2966 * 0x11 : Not Used? (0) 2967 * 0x12 : Bus Reset Delay Time (0x03) 2968 * 0x13 : Bootable CD Support 2969 * Value 0: Disable, 1: Enable 2970 * 0x14 : Device Scan 2971 * Bit 7 6 5 4 3 2 1 0 2972 * | <-----------------> 2973 * | SCSI ID: Value 0: Skip, 1: YES 2974 * |-> Value 0: ALL scan, Value 1: Manual 2975 * 0x15 - 0x1b : Not Used? (0) 2976 * 0x1c : Constant? (0x01) (clock div?) 2977 * 0x1d - 0x7c : Not Used (0xff) 2978 * 0x7d : Not Used? (0xff) 2979 * 0x7e : Constant (0x55), Validity signature 2980 * 0x7f : Constant (0xaa), Validity signature 2981 */ 2982 static int nsp32_getprom_at24(nsp32_hw_data *data) 2983 { 2984 int ret, i; 2985 int auto_sync; 2986 nsp32_target *target; 2987 int entry; 2988 2989 /* 2990 * Reset time which is designated by EEPROM. 2991 * 2992 * TODO: Not used yet. 2993 */ 2994 data->resettime = nsp32_prom_read(data, 0x12); 2995 2996 /* 2997 * HBA Synchronous Transfer Period 2998 * 2999 * Note: auto_sync = 0: auto, 1: manual. Ninja SCSI HBA spec says 3000 * that if auto_sync is 0 (auto), and connected SCSI devices are 3001 * same or lower than 3, then transfer speed is set as ULTRA-20M. 3002 * On the contrary if connected SCSI devices are same or higher 3003 * than 4, then transfer speed is set as FAST-10M. 3004 * 3005 * I break this rule. The number of connected SCSI devices are 3006 * only ignored. If auto_sync is 0 (auto), then transfer speed is 3007 * forced as ULTRA-20M. 3008 */ 3009 ret = nsp32_prom_read(data, 0x07); 3010 switch (ret) { 3011 case 0: 3012 auto_sync = TRUE; 3013 break; 3014 case 1: 3015 auto_sync = FALSE; 3016 break; 3017 default: 3018 nsp32_msg(KERN_WARNING, 3019 "Unsupported Auto Sync mode. Fall back to manual mode."); 3020 auto_sync = TRUE; 3021 } 3022 3023 if (trans_mode == ULTRA20M_MODE) { 3024 auto_sync = TRUE; 3025 } 3026 3027 /* 3028 * each device Synchronous Transfer Period 3029 */ 3030 for (i = 0; i < NSP32_HOST_SCSIID; i++) { 3031 target = &data->target[i]; 3032 if (auto_sync == TRUE) { 3033 target->limit_entry = 0; /* set as ULTRA20M */ 3034 } else { 3035 ret = nsp32_prom_read(data, i); 3036 entry = nsp32_search_period_entry(data, target, ret); 3037 if (entry < 0) { 3038 /* search failed... set maximum speed */ 3039 entry = 0; 3040 } 3041 target->limit_entry = entry; 3042 } 3043 } 3044 3045 return TRUE; 3046 } 3047 3048 3049 /* 3050 * C16 110 (I-O Data: SC-NBD) data map: 3051 * 3052 * ROMADDR 3053 * 0x00 - 0x06 : Device Synchronous Transfer Period (SCSI ID 0 - 6) 3054 * Value 0x0: 20MB/S, 0x1: 10MB/S, 0x2: 5MB/S, 0x3: ASYNC 3055 * 0x07 : 0 (HBA Synchronous Transfer Period: Auto Sync) 3056 * 0x08 - 0x0f : Not Used? (0x0) 3057 * 0x10 : Transfer Mode 3058 * Value 0: PIO, 1: Busmater 3059 * 0x11 : Bus Reset Delay Time (0x00-0x20) 3060 * 0x12 : Bus Termination 3061 * Value 0: Disable, 1: Enable 3062 * 0x13 - 0x19 : Disconnection 3063 * Value 0: Disable, 1: Enable 3064 * 0x1a - 0x7c : Not Used? (0) 3065 * 0x7d : Not Used? (0xf8) 3066 * 0x7e : Constant (0x55), Validity signature 3067 * 0x7f : Constant (0xaa), Validity signature 3068 */ 3069 static int nsp32_getprom_c16(nsp32_hw_data *data) 3070 { 3071 int ret, i; 3072 nsp32_target *target; 3073 int entry, val; 3074 3075 /* 3076 * Reset time which is designated by EEPROM. 3077 * 3078 * TODO: Not used yet. 3079 */ 3080 data->resettime = nsp32_prom_read(data, 0x11); 3081 3082 /* 3083 * each device Synchronous Transfer Period 3084 */ 3085 for (i = 0; i < NSP32_HOST_SCSIID; i++) { 3086 target = &data->target[i]; 3087 ret = nsp32_prom_read(data, i); 3088 switch (ret) { 3089 case 0: /* 20MB/s */ 3090 val = 0x0c; 3091 break; 3092 case 1: /* 10MB/s */ 3093 val = 0x19; 3094 break; 3095 case 2: /* 5MB/s */ 3096 val = 0x32; 3097 break; 3098 case 3: /* ASYNC */ 3099 val = 0x00; 3100 break; 3101 default: /* default 20MB/s */ 3102 val = 0x0c; 3103 break; 3104 } 3105 entry = nsp32_search_period_entry(data, target, val); 3106 if (entry < 0 || trans_mode == ULTRA20M_MODE) { 3107 /* search failed... set maximum speed */ 3108 entry = 0; 3109 } 3110 target->limit_entry = entry; 3111 } 3112 3113 return TRUE; 3114 } 3115 3116 3117 /* 3118 * Atmel AT24C01A (drived in 5V) serial EEPROM routines 3119 */ 3120 static int nsp32_prom_read(nsp32_hw_data *data, int romaddr) 3121 { 3122 int i, val; 3123 3124 /* start condition */ 3125 nsp32_prom_start(data); 3126 3127 /* device address */ 3128 nsp32_prom_write_bit(data, 1); /* 1 */ 3129 nsp32_prom_write_bit(data, 0); /* 0 */ 3130 nsp32_prom_write_bit(data, 1); /* 1 */ 3131 nsp32_prom_write_bit(data, 0); /* 0 */ 3132 nsp32_prom_write_bit(data, 0); /* A2: 0 (GND) */ 3133 nsp32_prom_write_bit(data, 0); /* A1: 0 (GND) */ 3134 nsp32_prom_write_bit(data, 0); /* A0: 0 (GND) */ 3135 3136 /* R/W: W for dummy write */ 3137 nsp32_prom_write_bit(data, 0); 3138 3139 /* ack */ 3140 nsp32_prom_write_bit(data, 0); 3141 3142 /* word address */ 3143 for (i = 7; i >= 0; i--) { 3144 nsp32_prom_write_bit(data, ((romaddr >> i) & 1)); 3145 } 3146 3147 /* ack */ 3148 nsp32_prom_write_bit(data, 0); 3149 3150 /* start condition */ 3151 nsp32_prom_start(data); 3152 3153 /* device address */ 3154 nsp32_prom_write_bit(data, 1); /* 1 */ 3155 nsp32_prom_write_bit(data, 0); /* 0 */ 3156 nsp32_prom_write_bit(data, 1); /* 1 */ 3157 nsp32_prom_write_bit(data, 0); /* 0 */ 3158 nsp32_prom_write_bit(data, 0); /* A2: 0 (GND) */ 3159 nsp32_prom_write_bit(data, 0); /* A1: 0 (GND) */ 3160 nsp32_prom_write_bit(data, 0); /* A0: 0 (GND) */ 3161 3162 /* R/W: R */ 3163 nsp32_prom_write_bit(data, 1); 3164 3165 /* ack */ 3166 nsp32_prom_write_bit(data, 0); 3167 3168 /* data... */ 3169 val = 0; 3170 for (i = 7; i >= 0; i--) { 3171 val += (nsp32_prom_read_bit(data) << i); 3172 } 3173 3174 /* no ack */ 3175 nsp32_prom_write_bit(data, 1); 3176 3177 /* stop condition */ 3178 nsp32_prom_stop(data); 3179 3180 return val; 3181 } 3182 3183 static void nsp32_prom_set(nsp32_hw_data *data, int bit, int val) 3184 { 3185 int base = data->BaseAddress; 3186 int tmp; 3187 3188 tmp = nsp32_index_read1(base, SERIAL_ROM_CTL); 3189 3190 if (val == 0) { 3191 tmp &= ~bit; 3192 } else { 3193 tmp |= bit; 3194 } 3195 3196 nsp32_index_write1(base, SERIAL_ROM_CTL, tmp); 3197 3198 udelay(10); 3199 } 3200 3201 static int nsp32_prom_get(nsp32_hw_data *data, int bit) 3202 { 3203 int base = data->BaseAddress; 3204 int tmp, ret; 3205 3206 if (bit != SDA) { 3207 nsp32_msg(KERN_ERR, "return value is not appropriate"); 3208 return 0; 3209 } 3210 3211 3212 tmp = nsp32_index_read1(base, SERIAL_ROM_CTL) & bit; 3213 3214 if (tmp == 0) { 3215 ret = 0; 3216 } else { 3217 ret = 1; 3218 } 3219 3220 udelay(10); 3221 3222 return ret; 3223 } 3224 3225 static void nsp32_prom_start (nsp32_hw_data *data) 3226 { 3227 /* start condition */ 3228 nsp32_prom_set(data, SCL, 1); 3229 nsp32_prom_set(data, SDA, 1); 3230 nsp32_prom_set(data, ENA, 1); /* output mode */ 3231 nsp32_prom_set(data, SDA, 0); /* keeping SCL=1 and transiting 3232 * SDA 1->0 is start condition */ 3233 nsp32_prom_set(data, SCL, 0); 3234 } 3235 3236 static void nsp32_prom_stop (nsp32_hw_data *data) 3237 { 3238 /* stop condition */ 3239 nsp32_prom_set(data, SCL, 1); 3240 nsp32_prom_set(data, SDA, 0); 3241 nsp32_prom_set(data, ENA, 1); /* output mode */ 3242 nsp32_prom_set(data, SDA, 1); 3243 nsp32_prom_set(data, SCL, 0); 3244 } 3245 3246 static void nsp32_prom_write_bit(nsp32_hw_data *data, int val) 3247 { 3248 /* write */ 3249 nsp32_prom_set(data, SDA, val); 3250 nsp32_prom_set(data, SCL, 1 ); 3251 nsp32_prom_set(data, SCL, 0 ); 3252 } 3253 3254 static int nsp32_prom_read_bit(nsp32_hw_data *data) 3255 { 3256 int val; 3257 3258 /* read */ 3259 nsp32_prom_set(data, ENA, 0); /* input mode */ 3260 nsp32_prom_set(data, SCL, 1); 3261 3262 val = nsp32_prom_get(data, SDA); 3263 3264 nsp32_prom_set(data, SCL, 0); 3265 nsp32_prom_set(data, ENA, 1); /* output mode */ 3266 3267 return val; 3268 } 3269 3270 3271 /************************************************************************** 3272 * Power Management 3273 */ 3274 #ifdef CONFIG_PM 3275 3276 /* Device suspended */ 3277 static int nsp32_suspend(struct pci_dev *pdev, pm_message_t state) 3278 { 3279 struct Scsi_Host *host = pci_get_drvdata(pdev); 3280 3281 nsp32_msg(KERN_INFO, "pci-suspend: pdev=0x%p, state=%ld, slot=%s, host=0x%p", pdev, state, pci_name(pdev), host); 3282 3283 pci_save_state (pdev); 3284 pci_disable_device (pdev); 3285 pci_set_power_state(pdev, pci_choose_state(pdev, state)); 3286 3287 return 0; 3288 } 3289 3290 /* Device woken up */ 3291 static int nsp32_resume(struct pci_dev *pdev) 3292 { 3293 struct Scsi_Host *host = pci_get_drvdata(pdev); 3294 nsp32_hw_data *data = (nsp32_hw_data *)host->hostdata; 3295 unsigned short reg; 3296 3297 nsp32_msg(KERN_INFO, "pci-resume: pdev=0x%p, slot=%s, host=0x%p", pdev, pci_name(pdev), host); 3298 3299 pci_set_power_state(pdev, PCI_D0); 3300 pci_enable_wake (pdev, PCI_D0, 0); 3301 pci_restore_state (pdev); 3302 3303 reg = nsp32_read2(data->BaseAddress, INDEX_REG); 3304 3305 nsp32_msg(KERN_INFO, "io=0x%x reg=0x%x", data->BaseAddress, reg); 3306 3307 if (reg == 0xffff) { 3308 nsp32_msg(KERN_INFO, "missing device. abort resume."); 3309 return 0; 3310 } 3311 3312 nsp32hw_init (data); 3313 nsp32_do_bus_reset(data); 3314 3315 nsp32_msg(KERN_INFO, "resume success"); 3316 3317 return 0; 3318 } 3319 3320 #endif 3321 3322 /************************************************************************ 3323 * PCI/Cardbus probe/remove routine 3324 */ 3325 static int nsp32_probe(struct pci_dev *pdev, const struct pci_device_id *id) 3326 { 3327 int ret; 3328 nsp32_hw_data *data = &nsp32_data_base; 3329 3330 nsp32_dbg(NSP32_DEBUG_REGISTER, "enter"); 3331 3332 ret = pci_enable_device(pdev); 3333 if (ret) { 3334 nsp32_msg(KERN_ERR, "failed to enable pci device"); 3335 return ret; 3336 } 3337 3338 data->Pci = pdev; 3339 data->pci_devid = id; 3340 data->IrqNumber = pdev->irq; 3341 data->BaseAddress = pci_resource_start(pdev, 0); 3342 data->NumAddress = pci_resource_len (pdev, 0); 3343 data->MmioAddress = pci_ioremap_bar(pdev, 1); 3344 data->MmioLength = pci_resource_len (pdev, 1); 3345 3346 pci_set_master(pdev); 3347 3348 ret = nsp32_detect(pdev); 3349 3350 nsp32_msg(KERN_INFO, "irq: %i mmio: %p+0x%lx slot: %s model: %s", 3351 pdev->irq, 3352 data->MmioAddress, data->MmioLength, 3353 pci_name(pdev), 3354 nsp32_model[id->driver_data]); 3355 3356 nsp32_dbg(NSP32_DEBUG_REGISTER, "exit %d", ret); 3357 3358 return ret; 3359 } 3360 3361 static void nsp32_remove(struct pci_dev *pdev) 3362 { 3363 struct Scsi_Host *host = pci_get_drvdata(pdev); 3364 3365 nsp32_dbg(NSP32_DEBUG_REGISTER, "enter"); 3366 3367 scsi_remove_host(host); 3368 3369 nsp32_release(host); 3370 3371 scsi_host_put(host); 3372 } 3373 3374 static struct pci_driver nsp32_driver = { 3375 .name = "nsp32", 3376 .id_table = nsp32_pci_table, 3377 .probe = nsp32_probe, 3378 .remove = nsp32_remove, 3379 #ifdef CONFIG_PM 3380 .suspend = nsp32_suspend, 3381 .resume = nsp32_resume, 3382 #endif 3383 }; 3384 3385 /********************************************************************* 3386 * Moule entry point 3387 */ 3388 static int __init init_nsp32(void) { 3389 nsp32_msg(KERN_INFO, "loading..."); 3390 return pci_register_driver(&nsp32_driver); 3391 } 3392 3393 static void __exit exit_nsp32(void) { 3394 nsp32_msg(KERN_INFO, "unloading..."); 3395 pci_unregister_driver(&nsp32_driver); 3396 } 3397 3398 module_init(init_nsp32); 3399 module_exit(exit_nsp32); 3400 3401 /* end */ 3402