xref: /openbmc/linux/drivers/scsi/mesh.h (revision 12eb4683)
1 /*
2  * mesh.h: definitions for the driver for the MESH SCSI bus adaptor
3  * (Macintosh Enhanced SCSI Hardware) found on Power Macintosh computers.
4  *
5  * Copyright (C) 1996 Paul Mackerras.
6  */
7 #ifndef _MESH_H
8 #define _MESH_H
9 
10 /*
11  * Registers in the MESH controller.
12  */
13 
14 struct mesh_regs {
15 	unsigned char	count_lo;
16 	char pad0[15];
17 	unsigned char	count_hi;
18 	char pad1[15];
19 	unsigned char	fifo;
20 	char pad2[15];
21 	unsigned char	sequence;
22 	char pad3[15];
23 	unsigned char	bus_status0;
24 	char pad4[15];
25 	unsigned char	bus_status1;
26 	char pad5[15];
27 	unsigned char	fifo_count;
28 	char pad6[15];
29 	unsigned char	exception;
30 	char pad7[15];
31 	unsigned char	error;
32 	char pad8[15];
33 	unsigned char	intr_mask;
34 	char pad9[15];
35 	unsigned char	interrupt;
36 	char pad10[15];
37 	unsigned char	source_id;
38 	char pad11[15];
39 	unsigned char	dest_id;
40 	char pad12[15];
41 	unsigned char	sync_params;
42 	char pad13[15];
43 	unsigned char	mesh_id;
44 	char pad14[15];
45 	unsigned char	sel_timeout;
46 	char pad15[15];
47 };
48 
49 /* Bits in the sequence register. */
50 #define SEQ_DMA_MODE	0x80	/* use DMA for data transfer */
51 #define SEQ_TARGET	0x40	/* put the controller into target mode */
52 #define SEQ_ATN		0x20	/* assert ATN signal */
53 #define SEQ_ACTIVE_NEG	0x10	/* use active negation on REQ/ACK */
54 #define SEQ_CMD		0x0f	/* command bits: */
55 #define SEQ_ARBITRATE	1	/*  get the bus */
56 #define SEQ_SELECT	2	/*  select a target */
57 #define SEQ_COMMAND	3	/*  send a command */
58 #define SEQ_STATUS	4	/*  receive status */
59 #define SEQ_DATAOUT	5	/*  send data */
60 #define SEQ_DATAIN	6	/*  receive data */
61 #define SEQ_MSGOUT	7	/*  send a message */
62 #define SEQ_MSGIN	8	/*  receive a message */
63 #define SEQ_BUSFREE	9	/*  look for bus free */
64 #define SEQ_ENBPARITY	0x0a	/*  enable parity checking */
65 #define SEQ_DISPARITY	0x0b	/*  disable parity checking */
66 #define SEQ_ENBRESEL	0x0c	/*  enable reselection */
67 #define SEQ_DISRESEL	0x0d	/*  disable reselection */
68 #define SEQ_RESETMESH	0x0e	/*  reset the controller */
69 #define SEQ_FLUSHFIFO	0x0f	/*  clear out the FIFO */
70 
71 /* Bits in the bus_status0 and bus_status1 registers:
72    these correspond directly to the SCSI bus control signals. */
73 #define BS0_REQ		0x20
74 #define BS0_ACK		0x10
75 #define BS0_ATN		0x08
76 #define BS0_MSG		0x04
77 #define BS0_CD		0x02
78 #define BS0_IO		0x01
79 #define BS1_RST		0x80
80 #define BS1_BSY		0x40
81 #define BS1_SEL		0x20
82 
83 /* Bus phases defined by the bits in bus_status0 */
84 #define BS0_PHASE	(BS0_MSG+BS0_CD+BS0_IO)
85 #define BP_DATAOUT	0
86 #define BP_DATAIN	BS0_IO
87 #define BP_COMMAND	BS0_CD
88 #define BP_STATUS	(BS0_CD+BS0_IO)
89 #define BP_MSGOUT	(BS0_MSG+BS0_CD)
90 #define BP_MSGIN	(BS0_MSG+BS0_CD+BS0_IO)
91 
92 /* Bits in the exception register. */
93 #define EXC_SELWATN	0x20	/* (as target) we were selected with ATN */
94 #define EXC_SELECTED	0x10	/* (as target) we were selected w/o ATN */
95 #define EXC_RESELECTED	0x08	/* (as initiator) we were reselected */
96 #define EXC_ARBLOST	0x04	/* we lost arbitration */
97 #define EXC_PHASEMM	0x02	/* SCSI phase mismatch */
98 #define EXC_SELTO	0x01	/* selection timeout */
99 
100 /* Bits in the error register */
101 #define ERR_UNEXPDISC	0x40	/* target unexpectedly disconnected */
102 #define ERR_SCSIRESET	0x20	/* SCSI bus got reset on us */
103 #define ERR_SEQERR	0x10	/* we did something the chip didn't like */
104 #define ERR_PARITY	0x01	/* parity error was detected */
105 
106 /* Bits in the interrupt and intr_mask registers */
107 #define INT_ERROR	0x04	/* error interrupt */
108 #define INT_EXCEPTION	0x02	/* exception interrupt */
109 #define INT_CMDDONE	0x01	/* command done interrupt */
110 
111 /* Fields in the sync_params register */
112 #define SYNC_OFF(x)	((x) >> 4)	/* offset field */
113 #define SYNC_PER(x)	((x) & 0xf)	/* period field */
114 #define SYNC_PARAMS(o, p)	(((o) << 4) | (p))
115 #define ASYNC_PARAMS	2	/* sync_params value for async xfers */
116 
117 /*
118  * Assuming a clock frequency of 50MHz:
119  *
120  * The transfer period with SYNC_PER(sync_params) == x
121  * is (x + 2) * 40ns, except that x == 0 gives 100ns.
122  *
123  * The units of the sel_timeout register are 10ms.
124  */
125 
126 
127 #endif /* _MESH_H */
128