1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * SCSI low-level driver for the MESH (Macintosh Enhanced SCSI Hardware) 4 * bus adaptor found on Power Macintosh computers. 5 * We assume the MESH is connected to a DBDMA (descriptor-based DMA) 6 * controller. 7 * 8 * Paul Mackerras, August 1996. 9 * Copyright (C) 1996 Paul Mackerras. 10 * 11 * Apr. 21 2002 - BenH Rework bus reset code for new error handler 12 * Add delay after initial bus reset 13 * Add module parameters 14 * 15 * Sep. 27 2003 - BenH Move to new driver model, fix some write posting 16 * issues 17 * To do: 18 * - handle aborts correctly 19 * - retry arbitration if lost (unless higher levels do this for us) 20 * - power down the chip when no device is detected 21 */ 22 #include <linux/module.h> 23 #include <linux/kernel.h> 24 #include <linux/delay.h> 25 #include <linux/types.h> 26 #include <linux/string.h> 27 #include <linux/blkdev.h> 28 #include <linux/proc_fs.h> 29 #include <linux/stat.h> 30 #include <linux/interrupt.h> 31 #include <linux/reboot.h> 32 #include <linux/spinlock.h> 33 #include <linux/pci.h> 34 #include <linux/pgtable.h> 35 #include <asm/dbdma.h> 36 #include <asm/io.h> 37 #include <asm/prom.h> 38 #include <asm/irq.h> 39 #include <asm/hydra.h> 40 #include <asm/processor.h> 41 #include <asm/machdep.h> 42 #include <asm/pmac_feature.h> 43 #include <asm/macio.h> 44 45 #include <scsi/scsi.h> 46 #include <scsi/scsi_cmnd.h> 47 #include <scsi/scsi_device.h> 48 #include <scsi/scsi_host.h> 49 50 #include "mesh.h" 51 52 #if 1 53 #undef KERN_DEBUG 54 #define KERN_DEBUG KERN_WARNING 55 #endif 56 57 MODULE_AUTHOR("Paul Mackerras (paulus@samba.org)"); 58 MODULE_DESCRIPTION("PowerMac MESH SCSI driver"); 59 MODULE_LICENSE("GPL"); 60 61 static int sync_rate = CONFIG_SCSI_MESH_SYNC_RATE; 62 static int sync_targets = 0xff; 63 static int resel_targets = 0xff; 64 static int debug_targets = 0; /* print debug for these targets */ 65 static int init_reset_delay = CONFIG_SCSI_MESH_RESET_DELAY_MS; 66 67 module_param(sync_rate, int, 0); 68 MODULE_PARM_DESC(sync_rate, "Synchronous rate (0..10, 0=async)"); 69 module_param(sync_targets, int, 0); 70 MODULE_PARM_DESC(sync_targets, "Bitmask of targets allowed to set synchronous"); 71 module_param(resel_targets, int, 0); 72 MODULE_PARM_DESC(resel_targets, "Bitmask of targets allowed to set disconnect"); 73 module_param(debug_targets, int, 0644); 74 MODULE_PARM_DESC(debug_targets, "Bitmask of debugged targets"); 75 module_param(init_reset_delay, int, 0); 76 MODULE_PARM_DESC(init_reset_delay, "Initial bus reset delay (0=no reset)"); 77 78 static int mesh_sync_period = 100; 79 static int mesh_sync_offset = 0; 80 static unsigned char use_active_neg = 0; /* bit mask for SEQ_ACTIVE_NEG if used */ 81 82 #define ALLOW_SYNC(tgt) ((sync_targets >> (tgt)) & 1) 83 #define ALLOW_RESEL(tgt) ((resel_targets >> (tgt)) & 1) 84 #define ALLOW_DEBUG(tgt) ((debug_targets >> (tgt)) & 1) 85 #define DEBUG_TARGET(cmd) ((cmd) && ALLOW_DEBUG((cmd)->device->id)) 86 87 #undef MESH_DBG 88 #define N_DBG_LOG 50 89 #define N_DBG_SLOG 20 90 #define NUM_DBG_EVENTS 13 91 #undef DBG_USE_TB /* bombs on 601 */ 92 93 struct dbglog { 94 char *fmt; 95 u32 tb; 96 u8 phase; 97 u8 bs0; 98 u8 bs1; 99 u8 tgt; 100 int d; 101 }; 102 103 enum mesh_phase { 104 idle, 105 arbitrating, 106 selecting, 107 commanding, 108 dataing, 109 statusing, 110 busfreeing, 111 disconnecting, 112 reselecting, 113 sleeping 114 }; 115 116 enum msg_phase { 117 msg_none, 118 msg_out, 119 msg_out_xxx, 120 msg_out_last, 121 msg_in, 122 msg_in_bad, 123 }; 124 125 enum sdtr_phase { 126 do_sdtr, 127 sdtr_sent, 128 sdtr_done 129 }; 130 131 struct mesh_target { 132 enum sdtr_phase sdtr_state; 133 int sync_params; 134 int data_goes_out; /* guess as to data direction */ 135 struct scsi_cmnd *current_req; 136 u32 saved_ptr; 137 #ifdef MESH_DBG 138 int log_ix; 139 int n_log; 140 struct dbglog log[N_DBG_LOG]; 141 #endif 142 }; 143 144 struct mesh_state { 145 volatile struct mesh_regs __iomem *mesh; 146 int meshintr; 147 volatile struct dbdma_regs __iomem *dma; 148 int dmaintr; 149 struct Scsi_Host *host; 150 struct mesh_state *next; 151 struct scsi_cmnd *request_q; 152 struct scsi_cmnd *request_qtail; 153 enum mesh_phase phase; /* what we're currently trying to do */ 154 enum msg_phase msgphase; 155 int conn_tgt; /* target we're connected to */ 156 struct scsi_cmnd *current_req; /* req we're currently working on */ 157 int data_ptr; 158 int dma_started; 159 int dma_count; 160 int stat; 161 int aborting; 162 int expect_reply; 163 int n_msgin; 164 u8 msgin[16]; 165 int n_msgout; 166 int last_n_msgout; 167 u8 msgout[16]; 168 struct dbdma_cmd *dma_cmds; /* space for dbdma commands, aligned */ 169 dma_addr_t dma_cmd_bus; 170 void *dma_cmd_space; 171 int dma_cmd_size; 172 int clk_freq; 173 struct mesh_target tgts[8]; 174 struct macio_dev *mdev; 175 struct pci_dev* pdev; 176 #ifdef MESH_DBG 177 int log_ix; 178 int n_log; 179 struct dbglog log[N_DBG_SLOG]; 180 #endif 181 }; 182 183 /* 184 * Driver is too messy, we need a few prototypes... 185 */ 186 static void mesh_done(struct mesh_state *ms, int start_next); 187 static void mesh_interrupt(struct mesh_state *ms); 188 static void cmd_complete(struct mesh_state *ms); 189 static void set_dma_cmds(struct mesh_state *ms, struct scsi_cmnd *cmd); 190 static void halt_dma(struct mesh_state *ms); 191 static void phase_mismatch(struct mesh_state *ms); 192 193 194 /* 195 * Some debugging & logging routines 196 */ 197 198 #ifdef MESH_DBG 199 200 static inline u32 readtb(void) 201 { 202 u32 tb; 203 204 #ifdef DBG_USE_TB 205 /* Beware: if you enable this, it will crash on 601s. */ 206 asm ("mftb %0" : "=r" (tb) : ); 207 #else 208 tb = 0; 209 #endif 210 return tb; 211 } 212 213 static void dlog(struct mesh_state *ms, char *fmt, int a) 214 { 215 struct mesh_target *tp = &ms->tgts[ms->conn_tgt]; 216 struct dbglog *tlp, *slp; 217 218 tlp = &tp->log[tp->log_ix]; 219 slp = &ms->log[ms->log_ix]; 220 tlp->fmt = fmt; 221 tlp->tb = readtb(); 222 tlp->phase = (ms->msgphase << 4) + ms->phase; 223 tlp->bs0 = ms->mesh->bus_status0; 224 tlp->bs1 = ms->mesh->bus_status1; 225 tlp->tgt = ms->conn_tgt; 226 tlp->d = a; 227 *slp = *tlp; 228 if (++tp->log_ix >= N_DBG_LOG) 229 tp->log_ix = 0; 230 if (tp->n_log < N_DBG_LOG) 231 ++tp->n_log; 232 if (++ms->log_ix >= N_DBG_SLOG) 233 ms->log_ix = 0; 234 if (ms->n_log < N_DBG_SLOG) 235 ++ms->n_log; 236 } 237 238 static void dumplog(struct mesh_state *ms, int t) 239 { 240 struct mesh_target *tp = &ms->tgts[t]; 241 struct dbglog *lp; 242 int i; 243 244 if (tp->n_log == 0) 245 return; 246 i = tp->log_ix - tp->n_log; 247 if (i < 0) 248 i += N_DBG_LOG; 249 tp->n_log = 0; 250 do { 251 lp = &tp->log[i]; 252 printk(KERN_DEBUG "mesh log %d: bs=%.2x%.2x ph=%.2x ", 253 t, lp->bs1, lp->bs0, lp->phase); 254 #ifdef DBG_USE_TB 255 printk("tb=%10u ", lp->tb); 256 #endif 257 printk(lp->fmt, lp->d); 258 printk("\n"); 259 if (++i >= N_DBG_LOG) 260 i = 0; 261 } while (i != tp->log_ix); 262 } 263 264 static void dumpslog(struct mesh_state *ms) 265 { 266 struct dbglog *lp; 267 int i; 268 269 if (ms->n_log == 0) 270 return; 271 i = ms->log_ix - ms->n_log; 272 if (i < 0) 273 i += N_DBG_SLOG; 274 ms->n_log = 0; 275 do { 276 lp = &ms->log[i]; 277 printk(KERN_DEBUG "mesh log: bs=%.2x%.2x ph=%.2x t%d ", 278 lp->bs1, lp->bs0, lp->phase, lp->tgt); 279 #ifdef DBG_USE_TB 280 printk("tb=%10u ", lp->tb); 281 #endif 282 printk(lp->fmt, lp->d); 283 printk("\n"); 284 if (++i >= N_DBG_SLOG) 285 i = 0; 286 } while (i != ms->log_ix); 287 } 288 289 #else 290 291 static inline void dlog(struct mesh_state *ms, char *fmt, int a) 292 {} 293 static inline void dumplog(struct mesh_state *ms, int tgt) 294 {} 295 static inline void dumpslog(struct mesh_state *ms) 296 {} 297 298 #endif /* MESH_DBG */ 299 300 #define MKWORD(a, b, c, d) (((a) << 24) + ((b) << 16) + ((c) << 8) + (d)) 301 302 static void 303 mesh_dump_regs(struct mesh_state *ms) 304 { 305 volatile struct mesh_regs __iomem *mr = ms->mesh; 306 volatile struct dbdma_regs __iomem *md = ms->dma; 307 int t; 308 struct mesh_target *tp; 309 310 printk(KERN_DEBUG "mesh: state at %p, regs at %p, dma at %p\n", 311 ms, mr, md); 312 printk(KERN_DEBUG " ct=%4x seq=%2x bs=%4x fc=%2x " 313 "exc=%2x err=%2x im=%2x int=%2x sp=%2x\n", 314 (mr->count_hi << 8) + mr->count_lo, mr->sequence, 315 (mr->bus_status1 << 8) + mr->bus_status0, mr->fifo_count, 316 mr->exception, mr->error, mr->intr_mask, mr->interrupt, 317 mr->sync_params); 318 while(in_8(&mr->fifo_count)) 319 printk(KERN_DEBUG " fifo data=%.2x\n",in_8(&mr->fifo)); 320 printk(KERN_DEBUG " dma stat=%x cmdptr=%x\n", 321 in_le32(&md->status), in_le32(&md->cmdptr)); 322 printk(KERN_DEBUG " phase=%d msgphase=%d conn_tgt=%d data_ptr=%d\n", 323 ms->phase, ms->msgphase, ms->conn_tgt, ms->data_ptr); 324 printk(KERN_DEBUG " dma_st=%d dma_ct=%d n_msgout=%d\n", 325 ms->dma_started, ms->dma_count, ms->n_msgout); 326 for (t = 0; t < 8; ++t) { 327 tp = &ms->tgts[t]; 328 if (tp->current_req == NULL) 329 continue; 330 printk(KERN_DEBUG " target %d: req=%p goes_out=%d saved_ptr=%d\n", 331 t, tp->current_req, tp->data_goes_out, tp->saved_ptr); 332 } 333 } 334 335 336 /* 337 * Flush write buffers on the bus path to the mesh 338 */ 339 static inline void mesh_flush_io(volatile struct mesh_regs __iomem *mr) 340 { 341 (void)in_8(&mr->mesh_id); 342 } 343 344 345 /* 346 * Complete a SCSI command 347 */ 348 static void mesh_completed(struct mesh_state *ms, struct scsi_cmnd *cmd) 349 { 350 (*cmd->scsi_done)(cmd); 351 } 352 353 354 /* Called with meshinterrupt disabled, initialize the chipset 355 * and eventually do the initial bus reset. The lock must not be 356 * held since we can schedule. 357 */ 358 static void mesh_init(struct mesh_state *ms) 359 { 360 volatile struct mesh_regs __iomem *mr = ms->mesh; 361 volatile struct dbdma_regs __iomem *md = ms->dma; 362 363 mesh_flush_io(mr); 364 udelay(100); 365 366 /* Reset controller */ 367 out_le32(&md->control, (RUN|PAUSE|FLUSH|WAKE) << 16); /* stop dma */ 368 out_8(&mr->exception, 0xff); /* clear all exception bits */ 369 out_8(&mr->error, 0xff); /* clear all error bits */ 370 out_8(&mr->sequence, SEQ_RESETMESH); 371 mesh_flush_io(mr); 372 udelay(10); 373 out_8(&mr->intr_mask, INT_ERROR | INT_EXCEPTION | INT_CMDDONE); 374 out_8(&mr->source_id, ms->host->this_id); 375 out_8(&mr->sel_timeout, 25); /* 250ms */ 376 out_8(&mr->sync_params, ASYNC_PARAMS); 377 378 if (init_reset_delay) { 379 printk(KERN_INFO "mesh: performing initial bus reset...\n"); 380 381 /* Reset bus */ 382 out_8(&mr->bus_status1, BS1_RST); /* assert RST */ 383 mesh_flush_io(mr); 384 udelay(30); /* leave it on for >= 25us */ 385 out_8(&mr->bus_status1, 0); /* negate RST */ 386 mesh_flush_io(mr); 387 388 /* Wait for bus to come back */ 389 msleep(init_reset_delay); 390 } 391 392 /* Reconfigure controller */ 393 out_8(&mr->interrupt, 0xff); /* clear all interrupt bits */ 394 out_8(&mr->sequence, SEQ_FLUSHFIFO); 395 mesh_flush_io(mr); 396 udelay(1); 397 out_8(&mr->sync_params, ASYNC_PARAMS); 398 out_8(&mr->sequence, SEQ_ENBRESEL); 399 400 ms->phase = idle; 401 ms->msgphase = msg_none; 402 } 403 404 405 static void mesh_start_cmd(struct mesh_state *ms, struct scsi_cmnd *cmd) 406 { 407 volatile struct mesh_regs __iomem *mr = ms->mesh; 408 int t, id; 409 410 id = cmd->device->id; 411 ms->current_req = cmd; 412 ms->tgts[id].data_goes_out = cmd->sc_data_direction == DMA_TO_DEVICE; 413 ms->tgts[id].current_req = cmd; 414 415 #if 1 416 if (DEBUG_TARGET(cmd)) { 417 int i; 418 printk(KERN_DEBUG "mesh_start: %p tgt=%d cmd=", cmd, id); 419 for (i = 0; i < cmd->cmd_len; ++i) 420 printk(" %x", cmd->cmnd[i]); 421 printk(" use_sg=%d buffer=%p bufflen=%u\n", 422 scsi_sg_count(cmd), scsi_sglist(cmd), scsi_bufflen(cmd)); 423 } 424 #endif 425 if (ms->dma_started) 426 panic("mesh: double DMA start !\n"); 427 428 ms->phase = arbitrating; 429 ms->msgphase = msg_none; 430 ms->data_ptr = 0; 431 ms->dma_started = 0; 432 ms->n_msgout = 0; 433 ms->last_n_msgout = 0; 434 ms->expect_reply = 0; 435 ms->conn_tgt = id; 436 ms->tgts[id].saved_ptr = 0; 437 ms->stat = DID_OK; 438 ms->aborting = 0; 439 #ifdef MESH_DBG 440 ms->tgts[id].n_log = 0; 441 dlog(ms, "start cmd=%x", (int) cmd); 442 #endif 443 444 /* Off we go */ 445 dlog(ms, "about to arb, intr/exc/err/fc=%.8x", 446 MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count)); 447 out_8(&mr->interrupt, INT_CMDDONE); 448 out_8(&mr->sequence, SEQ_ENBRESEL); 449 mesh_flush_io(mr); 450 udelay(1); 451 452 if (in_8(&mr->bus_status1) & (BS1_BSY | BS1_SEL)) { 453 /* 454 * Some other device has the bus or is arbitrating for it - 455 * probably a target which is about to reselect us. 456 */ 457 dlog(ms, "busy b4 arb, intr/exc/err/fc=%.8x", 458 MKWORD(mr->interrupt, mr->exception, 459 mr->error, mr->fifo_count)); 460 for (t = 100; t > 0; --t) { 461 if ((in_8(&mr->bus_status1) & (BS1_BSY | BS1_SEL)) == 0) 462 break; 463 if (in_8(&mr->interrupt) != 0) { 464 dlog(ms, "intr b4 arb, intr/exc/err/fc=%.8x", 465 MKWORD(mr->interrupt, mr->exception, 466 mr->error, mr->fifo_count)); 467 mesh_interrupt(ms); 468 if (ms->phase != arbitrating) 469 return; 470 } 471 udelay(1); 472 } 473 if (in_8(&mr->bus_status1) & (BS1_BSY | BS1_SEL)) { 474 /* XXX should try again in a little while */ 475 ms->stat = DID_BUS_BUSY; 476 ms->phase = idle; 477 mesh_done(ms, 0); 478 return; 479 } 480 } 481 482 /* 483 * Apparently the mesh has a bug where it will assert both its 484 * own bit and the target's bit on the bus during arbitration. 485 */ 486 out_8(&mr->dest_id, mr->source_id); 487 488 /* 489 * There appears to be a race with reselection sometimes, 490 * where a target reselects us just as we issue the 491 * arbitrate command. It seems that then the arbitrate 492 * command just hangs waiting for the bus to be free 493 * without giving us a reselection exception. 494 * The only way I have found to get it to respond correctly 495 * is this: disable reselection before issuing the arbitrate 496 * command, then after issuing it, if it looks like a target 497 * is trying to reselect us, reset the mesh and then enable 498 * reselection. 499 */ 500 out_8(&mr->sequence, SEQ_DISRESEL); 501 if (in_8(&mr->interrupt) != 0) { 502 dlog(ms, "intr after disresel, intr/exc/err/fc=%.8x", 503 MKWORD(mr->interrupt, mr->exception, 504 mr->error, mr->fifo_count)); 505 mesh_interrupt(ms); 506 if (ms->phase != arbitrating) 507 return; 508 dlog(ms, "after intr after disresel, intr/exc/err/fc=%.8x", 509 MKWORD(mr->interrupt, mr->exception, 510 mr->error, mr->fifo_count)); 511 } 512 513 out_8(&mr->sequence, SEQ_ARBITRATE); 514 515 for (t = 230; t > 0; --t) { 516 if (in_8(&mr->interrupt) != 0) 517 break; 518 udelay(1); 519 } 520 dlog(ms, "after arb, intr/exc/err/fc=%.8x", 521 MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count)); 522 if (in_8(&mr->interrupt) == 0 && (in_8(&mr->bus_status1) & BS1_SEL) 523 && (in_8(&mr->bus_status0) & BS0_IO)) { 524 /* looks like a reselection - try resetting the mesh */ 525 dlog(ms, "resel? after arb, intr/exc/err/fc=%.8x", 526 MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count)); 527 out_8(&mr->sequence, SEQ_RESETMESH); 528 mesh_flush_io(mr); 529 udelay(10); 530 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE); 531 out_8(&mr->intr_mask, INT_ERROR | INT_EXCEPTION | INT_CMDDONE); 532 out_8(&mr->sequence, SEQ_ENBRESEL); 533 mesh_flush_io(mr); 534 for (t = 10; t > 0 && in_8(&mr->interrupt) == 0; --t) 535 udelay(1); 536 dlog(ms, "tried reset after arb, intr/exc/err/fc=%.8x", 537 MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count)); 538 #ifndef MESH_MULTIPLE_HOSTS 539 if (in_8(&mr->interrupt) == 0 && (in_8(&mr->bus_status1) & BS1_SEL) 540 && (in_8(&mr->bus_status0) & BS0_IO)) { 541 printk(KERN_ERR "mesh: controller not responding" 542 " to reselection!\n"); 543 /* 544 * If this is a target reselecting us, and the 545 * mesh isn't responding, the higher levels of 546 * the scsi code will eventually time out and 547 * reset the bus. 548 */ 549 } 550 #endif 551 } 552 } 553 554 /* 555 * Start the next command for a MESH. 556 * Should be called with interrupts disabled. 557 */ 558 static void mesh_start(struct mesh_state *ms) 559 { 560 struct scsi_cmnd *cmd, *prev, *next; 561 562 if (ms->phase != idle || ms->current_req != NULL) { 563 printk(KERN_ERR "inappropriate mesh_start (phase=%d, ms=%p)", 564 ms->phase, ms); 565 return; 566 } 567 568 while (ms->phase == idle) { 569 prev = NULL; 570 for (cmd = ms->request_q; ; cmd = (struct scsi_cmnd *) cmd->host_scribble) { 571 if (cmd == NULL) 572 return; 573 if (ms->tgts[cmd->device->id].current_req == NULL) 574 break; 575 prev = cmd; 576 } 577 next = (struct scsi_cmnd *) cmd->host_scribble; 578 if (prev == NULL) 579 ms->request_q = next; 580 else 581 prev->host_scribble = (void *) next; 582 if (next == NULL) 583 ms->request_qtail = prev; 584 585 mesh_start_cmd(ms, cmd); 586 } 587 } 588 589 static void mesh_done(struct mesh_state *ms, int start_next) 590 { 591 struct scsi_cmnd *cmd; 592 struct mesh_target *tp = &ms->tgts[ms->conn_tgt]; 593 594 cmd = ms->current_req; 595 ms->current_req = NULL; 596 tp->current_req = NULL; 597 if (cmd) { 598 cmd->result = (ms->stat << 16) | cmd->SCp.Status; 599 if (ms->stat == DID_OK) 600 cmd->result |= cmd->SCp.Message << 8; 601 if (DEBUG_TARGET(cmd)) { 602 printk(KERN_DEBUG "mesh_done: result = %x, data_ptr=%d, buflen=%d\n", 603 cmd->result, ms->data_ptr, scsi_bufflen(cmd)); 604 #if 0 605 /* needs to use sg? */ 606 if ((cmd->cmnd[0] == 0 || cmd->cmnd[0] == 0x12 || cmd->cmnd[0] == 3) 607 && cmd->request_buffer != 0) { 608 unsigned char *b = cmd->request_buffer; 609 printk(KERN_DEBUG "buffer = %x %x %x %x %x %x %x %x\n", 610 b[0], b[1], b[2], b[3], b[4], b[5], b[6], b[7]); 611 } 612 #endif 613 } 614 cmd->SCp.this_residual -= ms->data_ptr; 615 mesh_completed(ms, cmd); 616 } 617 if (start_next) { 618 out_8(&ms->mesh->sequence, SEQ_ENBRESEL); 619 mesh_flush_io(ms->mesh); 620 udelay(1); 621 ms->phase = idle; 622 mesh_start(ms); 623 } 624 } 625 626 static inline void add_sdtr_msg(struct mesh_state *ms) 627 { 628 int i = ms->n_msgout; 629 630 ms->msgout[i] = EXTENDED_MESSAGE; 631 ms->msgout[i+1] = 3; 632 ms->msgout[i+2] = EXTENDED_SDTR; 633 ms->msgout[i+3] = mesh_sync_period/4; 634 ms->msgout[i+4] = (ALLOW_SYNC(ms->conn_tgt)? mesh_sync_offset: 0); 635 ms->n_msgout = i + 5; 636 } 637 638 static void set_sdtr(struct mesh_state *ms, int period, int offset) 639 { 640 struct mesh_target *tp = &ms->tgts[ms->conn_tgt]; 641 volatile struct mesh_regs __iomem *mr = ms->mesh; 642 int v, tr; 643 644 tp->sdtr_state = sdtr_done; 645 if (offset == 0) { 646 /* asynchronous */ 647 if (SYNC_OFF(tp->sync_params)) 648 printk(KERN_INFO "mesh: target %d now asynchronous\n", 649 ms->conn_tgt); 650 tp->sync_params = ASYNC_PARAMS; 651 out_8(&mr->sync_params, ASYNC_PARAMS); 652 return; 653 } 654 /* 655 * We need to compute ceil(clk_freq * period / 500e6) - 2 656 * without incurring overflow. 657 */ 658 v = (ms->clk_freq / 5000) * period; 659 if (v <= 250000) { 660 /* special case: sync_period == 5 * clk_period */ 661 v = 0; 662 /* units of tr are 100kB/s */ 663 tr = (ms->clk_freq + 250000) / 500000; 664 } else { 665 /* sync_period == (v + 2) * 2 * clk_period */ 666 v = (v + 99999) / 100000 - 2; 667 if (v > 15) 668 v = 15; /* oops */ 669 tr = ((ms->clk_freq / (v + 2)) + 199999) / 200000; 670 } 671 if (offset > 15) 672 offset = 15; /* can't happen */ 673 tp->sync_params = SYNC_PARAMS(offset, v); 674 out_8(&mr->sync_params, tp->sync_params); 675 printk(KERN_INFO "mesh: target %d synchronous at %d.%d MB/s\n", 676 ms->conn_tgt, tr/10, tr%10); 677 } 678 679 static void start_phase(struct mesh_state *ms) 680 { 681 int i, seq, nb; 682 volatile struct mesh_regs __iomem *mr = ms->mesh; 683 volatile struct dbdma_regs __iomem *md = ms->dma; 684 struct scsi_cmnd *cmd = ms->current_req; 685 struct mesh_target *tp = &ms->tgts[ms->conn_tgt]; 686 687 dlog(ms, "start_phase nmo/exc/fc/seq = %.8x", 688 MKWORD(ms->n_msgout, mr->exception, mr->fifo_count, mr->sequence)); 689 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE); 690 seq = use_active_neg + (ms->n_msgout? SEQ_ATN: 0); 691 switch (ms->msgphase) { 692 case msg_none: 693 break; 694 695 case msg_in: 696 out_8(&mr->count_hi, 0); 697 out_8(&mr->count_lo, 1); 698 out_8(&mr->sequence, SEQ_MSGIN + seq); 699 ms->n_msgin = 0; 700 return; 701 702 case msg_out: 703 /* 704 * To make sure ATN drops before we assert ACK for 705 * the last byte of the message, we have to do the 706 * last byte specially. 707 */ 708 if (ms->n_msgout <= 0) { 709 printk(KERN_ERR "mesh: msg_out but n_msgout=%d\n", 710 ms->n_msgout); 711 mesh_dump_regs(ms); 712 ms->msgphase = msg_none; 713 break; 714 } 715 if (ALLOW_DEBUG(ms->conn_tgt)) { 716 printk(KERN_DEBUG "mesh: sending %d msg bytes:", 717 ms->n_msgout); 718 for (i = 0; i < ms->n_msgout; ++i) 719 printk(" %x", ms->msgout[i]); 720 printk("\n"); 721 } 722 dlog(ms, "msgout msg=%.8x", MKWORD(ms->n_msgout, ms->msgout[0], 723 ms->msgout[1], ms->msgout[2])); 724 out_8(&mr->count_hi, 0); 725 out_8(&mr->sequence, SEQ_FLUSHFIFO); 726 mesh_flush_io(mr); 727 udelay(1); 728 /* 729 * If ATN is not already asserted, we assert it, then 730 * issue a SEQ_MSGOUT to get the mesh to drop ACK. 731 */ 732 if ((in_8(&mr->bus_status0) & BS0_ATN) == 0) { 733 dlog(ms, "bus0 was %.2x explicitly asserting ATN", mr->bus_status0); 734 out_8(&mr->bus_status0, BS0_ATN); /* explicit ATN */ 735 mesh_flush_io(mr); 736 udelay(1); 737 out_8(&mr->count_lo, 1); 738 out_8(&mr->sequence, SEQ_MSGOUT + seq); 739 out_8(&mr->bus_status0, 0); /* release explicit ATN */ 740 dlog(ms,"hace: after explicit ATN bus0=%.2x",mr->bus_status0); 741 } 742 if (ms->n_msgout == 1) { 743 /* 744 * We can't issue the SEQ_MSGOUT without ATN 745 * until the target has asserted REQ. The logic 746 * in cmd_complete handles both situations: 747 * REQ already asserted or not. 748 */ 749 cmd_complete(ms); 750 } else { 751 out_8(&mr->count_lo, ms->n_msgout - 1); 752 out_8(&mr->sequence, SEQ_MSGOUT + seq); 753 for (i = 0; i < ms->n_msgout - 1; ++i) 754 out_8(&mr->fifo, ms->msgout[i]); 755 } 756 return; 757 758 default: 759 printk(KERN_ERR "mesh bug: start_phase msgphase=%d\n", 760 ms->msgphase); 761 } 762 763 switch (ms->phase) { 764 case selecting: 765 out_8(&mr->dest_id, ms->conn_tgt); 766 out_8(&mr->sequence, SEQ_SELECT + SEQ_ATN); 767 break; 768 case commanding: 769 out_8(&mr->sync_params, tp->sync_params); 770 out_8(&mr->count_hi, 0); 771 if (cmd) { 772 out_8(&mr->count_lo, cmd->cmd_len); 773 out_8(&mr->sequence, SEQ_COMMAND + seq); 774 for (i = 0; i < cmd->cmd_len; ++i) 775 out_8(&mr->fifo, cmd->cmnd[i]); 776 } else { 777 out_8(&mr->count_lo, 6); 778 out_8(&mr->sequence, SEQ_COMMAND + seq); 779 for (i = 0; i < 6; ++i) 780 out_8(&mr->fifo, 0); 781 } 782 break; 783 case dataing: 784 /* transfer data, if any */ 785 if (!ms->dma_started) { 786 set_dma_cmds(ms, cmd); 787 out_le32(&md->cmdptr, virt_to_phys(ms->dma_cmds)); 788 out_le32(&md->control, (RUN << 16) | RUN); 789 ms->dma_started = 1; 790 } 791 nb = ms->dma_count; 792 if (nb > 0xfff0) 793 nb = 0xfff0; 794 ms->dma_count -= nb; 795 ms->data_ptr += nb; 796 out_8(&mr->count_lo, nb); 797 out_8(&mr->count_hi, nb >> 8); 798 out_8(&mr->sequence, (tp->data_goes_out? 799 SEQ_DATAOUT: SEQ_DATAIN) + SEQ_DMA_MODE + seq); 800 break; 801 case statusing: 802 out_8(&mr->count_hi, 0); 803 out_8(&mr->count_lo, 1); 804 out_8(&mr->sequence, SEQ_STATUS + seq); 805 break; 806 case busfreeing: 807 case disconnecting: 808 out_8(&mr->sequence, SEQ_ENBRESEL); 809 mesh_flush_io(mr); 810 udelay(1); 811 dlog(ms, "enbresel intr/exc/err/fc=%.8x", 812 MKWORD(mr->interrupt, mr->exception, mr->error, 813 mr->fifo_count)); 814 out_8(&mr->sequence, SEQ_BUSFREE); 815 break; 816 default: 817 printk(KERN_ERR "mesh: start_phase called with phase=%d\n", 818 ms->phase); 819 dumpslog(ms); 820 } 821 822 } 823 824 static inline void get_msgin(struct mesh_state *ms) 825 { 826 volatile struct mesh_regs __iomem *mr = ms->mesh; 827 int i, n; 828 829 n = mr->fifo_count; 830 if (n != 0) { 831 i = ms->n_msgin; 832 ms->n_msgin = i + n; 833 for (; n > 0; --n) 834 ms->msgin[i++] = in_8(&mr->fifo); 835 } 836 } 837 838 static inline int msgin_length(struct mesh_state *ms) 839 { 840 int b, n; 841 842 n = 1; 843 if (ms->n_msgin > 0) { 844 b = ms->msgin[0]; 845 if (b == 1) { 846 /* extended message */ 847 n = ms->n_msgin < 2? 2: ms->msgin[1] + 2; 848 } else if (0x20 <= b && b <= 0x2f) { 849 /* 2-byte message */ 850 n = 2; 851 } 852 } 853 return n; 854 } 855 856 static void reselected(struct mesh_state *ms) 857 { 858 volatile struct mesh_regs __iomem *mr = ms->mesh; 859 struct scsi_cmnd *cmd; 860 struct mesh_target *tp; 861 int b, t, prev; 862 863 switch (ms->phase) { 864 case idle: 865 break; 866 case arbitrating: 867 if ((cmd = ms->current_req) != NULL) { 868 /* put the command back on the queue */ 869 cmd->host_scribble = (void *) ms->request_q; 870 if (ms->request_q == NULL) 871 ms->request_qtail = cmd; 872 ms->request_q = cmd; 873 tp = &ms->tgts[cmd->device->id]; 874 tp->current_req = NULL; 875 } 876 break; 877 case busfreeing: 878 ms->phase = reselecting; 879 mesh_done(ms, 0); 880 break; 881 case disconnecting: 882 break; 883 default: 884 printk(KERN_ERR "mesh: reselected in phase %d/%d tgt %d\n", 885 ms->msgphase, ms->phase, ms->conn_tgt); 886 dumplog(ms, ms->conn_tgt); 887 dumpslog(ms); 888 } 889 890 if (ms->dma_started) { 891 printk(KERN_ERR "mesh: reselected with DMA started !\n"); 892 halt_dma(ms); 893 } 894 ms->current_req = NULL; 895 ms->phase = dataing; 896 ms->msgphase = msg_in; 897 ms->n_msgout = 0; 898 ms->last_n_msgout = 0; 899 prev = ms->conn_tgt; 900 901 /* 902 * We seem to get abortive reselections sometimes. 903 */ 904 while ((in_8(&mr->bus_status1) & BS1_BSY) == 0) { 905 static int mesh_aborted_resels; 906 mesh_aborted_resels++; 907 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE); 908 mesh_flush_io(mr); 909 udelay(1); 910 out_8(&mr->sequence, SEQ_ENBRESEL); 911 mesh_flush_io(mr); 912 udelay(5); 913 dlog(ms, "extra resel err/exc/fc = %.6x", 914 MKWORD(0, mr->error, mr->exception, mr->fifo_count)); 915 } 916 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE); 917 mesh_flush_io(mr); 918 udelay(1); 919 out_8(&mr->sequence, SEQ_ENBRESEL); 920 mesh_flush_io(mr); 921 udelay(1); 922 out_8(&mr->sync_params, ASYNC_PARAMS); 923 924 /* 925 * Find out who reselected us. 926 */ 927 if (in_8(&mr->fifo_count) == 0) { 928 printk(KERN_ERR "mesh: reselection but nothing in fifo?\n"); 929 ms->conn_tgt = ms->host->this_id; 930 goto bogus; 931 } 932 /* get the last byte in the fifo */ 933 do { 934 b = in_8(&mr->fifo); 935 dlog(ms, "reseldata %x", b); 936 } while (in_8(&mr->fifo_count)); 937 for (t = 0; t < 8; ++t) 938 if ((b & (1 << t)) != 0 && t != ms->host->this_id) 939 break; 940 if (b != (1 << t) + (1 << ms->host->this_id)) { 941 printk(KERN_ERR "mesh: bad reselection data %x\n", b); 942 ms->conn_tgt = ms->host->this_id; 943 goto bogus; 944 } 945 946 947 /* 948 * Set up to continue with that target's transfer. 949 */ 950 ms->conn_tgt = t; 951 tp = &ms->tgts[t]; 952 out_8(&mr->sync_params, tp->sync_params); 953 if (ALLOW_DEBUG(t)) { 954 printk(KERN_DEBUG "mesh: reselected by target %d\n", t); 955 printk(KERN_DEBUG "mesh: saved_ptr=%x goes_out=%d cmd=%p\n", 956 tp->saved_ptr, tp->data_goes_out, tp->current_req); 957 } 958 ms->current_req = tp->current_req; 959 if (tp->current_req == NULL) { 960 printk(KERN_ERR "mesh: reselected by tgt %d but no cmd!\n", t); 961 goto bogus; 962 } 963 ms->data_ptr = tp->saved_ptr; 964 dlog(ms, "resel prev tgt=%d", prev); 965 dlog(ms, "resel err/exc=%.4x", MKWORD(0, 0, mr->error, mr->exception)); 966 start_phase(ms); 967 return; 968 969 bogus: 970 dumplog(ms, ms->conn_tgt); 971 dumpslog(ms); 972 ms->data_ptr = 0; 973 ms->aborting = 1; 974 start_phase(ms); 975 } 976 977 static void do_abort(struct mesh_state *ms) 978 { 979 ms->msgout[0] = ABORT; 980 ms->n_msgout = 1; 981 ms->aborting = 1; 982 ms->stat = DID_ABORT; 983 dlog(ms, "abort", 0); 984 } 985 986 static void handle_reset(struct mesh_state *ms) 987 { 988 int tgt; 989 struct mesh_target *tp; 990 struct scsi_cmnd *cmd; 991 volatile struct mesh_regs __iomem *mr = ms->mesh; 992 993 for (tgt = 0; tgt < 8; ++tgt) { 994 tp = &ms->tgts[tgt]; 995 if ((cmd = tp->current_req) != NULL) { 996 cmd->result = DID_RESET << 16; 997 tp->current_req = NULL; 998 mesh_completed(ms, cmd); 999 } 1000 ms->tgts[tgt].sdtr_state = do_sdtr; 1001 ms->tgts[tgt].sync_params = ASYNC_PARAMS; 1002 } 1003 ms->current_req = NULL; 1004 while ((cmd = ms->request_q) != NULL) { 1005 ms->request_q = (struct scsi_cmnd *) cmd->host_scribble; 1006 cmd->result = DID_RESET << 16; 1007 mesh_completed(ms, cmd); 1008 } 1009 ms->phase = idle; 1010 ms->msgphase = msg_none; 1011 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE); 1012 out_8(&mr->sequence, SEQ_FLUSHFIFO); 1013 mesh_flush_io(mr); 1014 udelay(1); 1015 out_8(&mr->sync_params, ASYNC_PARAMS); 1016 out_8(&mr->sequence, SEQ_ENBRESEL); 1017 } 1018 1019 static irqreturn_t do_mesh_interrupt(int irq, void *dev_id) 1020 { 1021 unsigned long flags; 1022 struct mesh_state *ms = dev_id; 1023 struct Scsi_Host *dev = ms->host; 1024 1025 spin_lock_irqsave(dev->host_lock, flags); 1026 mesh_interrupt(ms); 1027 spin_unlock_irqrestore(dev->host_lock, flags); 1028 return IRQ_HANDLED; 1029 } 1030 1031 static void handle_error(struct mesh_state *ms) 1032 { 1033 int err, exc, count; 1034 volatile struct mesh_regs __iomem *mr = ms->mesh; 1035 1036 err = in_8(&mr->error); 1037 exc = in_8(&mr->exception); 1038 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE); 1039 dlog(ms, "error err/exc/fc/cl=%.8x", 1040 MKWORD(err, exc, mr->fifo_count, mr->count_lo)); 1041 if (err & ERR_SCSIRESET) { 1042 /* SCSI bus was reset */ 1043 printk(KERN_INFO "mesh: SCSI bus reset detected: " 1044 "waiting for end..."); 1045 while ((in_8(&mr->bus_status1) & BS1_RST) != 0) 1046 udelay(1); 1047 printk("done\n"); 1048 handle_reset(ms); 1049 /* request_q is empty, no point in mesh_start() */ 1050 return; 1051 } 1052 if (err & ERR_UNEXPDISC) { 1053 /* Unexpected disconnect */ 1054 if (exc & EXC_RESELECTED) { 1055 reselected(ms); 1056 return; 1057 } 1058 if (!ms->aborting) { 1059 printk(KERN_WARNING "mesh: target %d aborted\n", 1060 ms->conn_tgt); 1061 dumplog(ms, ms->conn_tgt); 1062 dumpslog(ms); 1063 } 1064 out_8(&mr->interrupt, INT_CMDDONE); 1065 ms->stat = DID_ABORT; 1066 mesh_done(ms, 1); 1067 return; 1068 } 1069 if (err & ERR_PARITY) { 1070 if (ms->msgphase == msg_in) { 1071 printk(KERN_ERR "mesh: msg parity error, target %d\n", 1072 ms->conn_tgt); 1073 ms->msgout[0] = MSG_PARITY_ERROR; 1074 ms->n_msgout = 1; 1075 ms->msgphase = msg_in_bad; 1076 cmd_complete(ms); 1077 return; 1078 } 1079 if (ms->stat == DID_OK) { 1080 printk(KERN_ERR "mesh: parity error, target %d\n", 1081 ms->conn_tgt); 1082 ms->stat = DID_PARITY; 1083 } 1084 count = (mr->count_hi << 8) + mr->count_lo; 1085 if (count == 0) { 1086 cmd_complete(ms); 1087 } else { 1088 /* reissue the data transfer command */ 1089 out_8(&mr->sequence, mr->sequence); 1090 } 1091 return; 1092 } 1093 if (err & ERR_SEQERR) { 1094 if (exc & EXC_RESELECTED) { 1095 /* This can happen if we issue a command to 1096 get the bus just after the target reselects us. */ 1097 static int mesh_resel_seqerr; 1098 mesh_resel_seqerr++; 1099 reselected(ms); 1100 return; 1101 } 1102 if (exc == EXC_PHASEMM) { 1103 static int mesh_phasemm_seqerr; 1104 mesh_phasemm_seqerr++; 1105 phase_mismatch(ms); 1106 return; 1107 } 1108 printk(KERN_ERR "mesh: sequence error (err=%x exc=%x)\n", 1109 err, exc); 1110 } else { 1111 printk(KERN_ERR "mesh: unknown error %x (exc=%x)\n", err, exc); 1112 } 1113 mesh_dump_regs(ms); 1114 dumplog(ms, ms->conn_tgt); 1115 if (ms->phase > selecting && (in_8(&mr->bus_status1) & BS1_BSY)) { 1116 /* try to do what the target wants */ 1117 do_abort(ms); 1118 phase_mismatch(ms); 1119 return; 1120 } 1121 ms->stat = DID_ERROR; 1122 mesh_done(ms, 1); 1123 } 1124 1125 static void handle_exception(struct mesh_state *ms) 1126 { 1127 int exc; 1128 volatile struct mesh_regs __iomem *mr = ms->mesh; 1129 1130 exc = in_8(&mr->exception); 1131 out_8(&mr->interrupt, INT_EXCEPTION | INT_CMDDONE); 1132 if (exc & EXC_RESELECTED) { 1133 static int mesh_resel_exc; 1134 mesh_resel_exc++; 1135 reselected(ms); 1136 } else if (exc == EXC_ARBLOST) { 1137 printk(KERN_DEBUG "mesh: lost arbitration\n"); 1138 ms->stat = DID_BUS_BUSY; 1139 mesh_done(ms, 1); 1140 } else if (exc == EXC_SELTO) { 1141 /* selection timed out */ 1142 ms->stat = DID_BAD_TARGET; 1143 mesh_done(ms, 1); 1144 } else if (exc == EXC_PHASEMM) { 1145 /* target wants to do something different: 1146 find out what it wants and do it. */ 1147 phase_mismatch(ms); 1148 } else { 1149 printk(KERN_ERR "mesh: can't cope with exception %x\n", exc); 1150 mesh_dump_regs(ms); 1151 dumplog(ms, ms->conn_tgt); 1152 do_abort(ms); 1153 phase_mismatch(ms); 1154 } 1155 } 1156 1157 static void handle_msgin(struct mesh_state *ms) 1158 { 1159 int i, code; 1160 struct scsi_cmnd *cmd = ms->current_req; 1161 struct mesh_target *tp = &ms->tgts[ms->conn_tgt]; 1162 1163 if (ms->n_msgin == 0) 1164 return; 1165 code = ms->msgin[0]; 1166 if (ALLOW_DEBUG(ms->conn_tgt)) { 1167 printk(KERN_DEBUG "got %d message bytes:", ms->n_msgin); 1168 for (i = 0; i < ms->n_msgin; ++i) 1169 printk(" %x", ms->msgin[i]); 1170 printk("\n"); 1171 } 1172 dlog(ms, "msgin msg=%.8x", 1173 MKWORD(ms->n_msgin, code, ms->msgin[1], ms->msgin[2])); 1174 1175 ms->expect_reply = 0; 1176 ms->n_msgout = 0; 1177 if (ms->n_msgin < msgin_length(ms)) 1178 goto reject; 1179 if (cmd) 1180 cmd->SCp.Message = code; 1181 switch (code) { 1182 case COMMAND_COMPLETE: 1183 break; 1184 case EXTENDED_MESSAGE: 1185 switch (ms->msgin[2]) { 1186 case EXTENDED_MODIFY_DATA_POINTER: 1187 ms->data_ptr += (ms->msgin[3] << 24) + ms->msgin[6] 1188 + (ms->msgin[4] << 16) + (ms->msgin[5] << 8); 1189 break; 1190 case EXTENDED_SDTR: 1191 if (tp->sdtr_state != sdtr_sent) { 1192 /* reply with an SDTR */ 1193 add_sdtr_msg(ms); 1194 /* limit period to at least his value, 1195 offset to no more than his */ 1196 if (ms->msgout[3] < ms->msgin[3]) 1197 ms->msgout[3] = ms->msgin[3]; 1198 if (ms->msgout[4] > ms->msgin[4]) 1199 ms->msgout[4] = ms->msgin[4]; 1200 set_sdtr(ms, ms->msgout[3], ms->msgout[4]); 1201 ms->msgphase = msg_out; 1202 } else { 1203 set_sdtr(ms, ms->msgin[3], ms->msgin[4]); 1204 } 1205 break; 1206 default: 1207 goto reject; 1208 } 1209 break; 1210 case SAVE_POINTERS: 1211 tp->saved_ptr = ms->data_ptr; 1212 break; 1213 case RESTORE_POINTERS: 1214 ms->data_ptr = tp->saved_ptr; 1215 break; 1216 case DISCONNECT: 1217 ms->phase = disconnecting; 1218 break; 1219 case ABORT: 1220 break; 1221 case MESSAGE_REJECT: 1222 if (tp->sdtr_state == sdtr_sent) 1223 set_sdtr(ms, 0, 0); 1224 break; 1225 case NOP: 1226 break; 1227 default: 1228 if (IDENTIFY_BASE <= code && code <= IDENTIFY_BASE + 7) { 1229 if (cmd == NULL) { 1230 do_abort(ms); 1231 ms->msgphase = msg_out; 1232 } else if (code != cmd->device->lun + IDENTIFY_BASE) { 1233 printk(KERN_WARNING "mesh: lun mismatch " 1234 "(%d != %llu) on reselection from " 1235 "target %d\n", code - IDENTIFY_BASE, 1236 cmd->device->lun, ms->conn_tgt); 1237 } 1238 break; 1239 } 1240 goto reject; 1241 } 1242 return; 1243 1244 reject: 1245 printk(KERN_WARNING "mesh: rejecting message from target %d:", 1246 ms->conn_tgt); 1247 for (i = 0; i < ms->n_msgin; ++i) 1248 printk(" %x", ms->msgin[i]); 1249 printk("\n"); 1250 ms->msgout[0] = MESSAGE_REJECT; 1251 ms->n_msgout = 1; 1252 ms->msgphase = msg_out; 1253 } 1254 1255 /* 1256 * Set up DMA commands for transferring data. 1257 */ 1258 static void set_dma_cmds(struct mesh_state *ms, struct scsi_cmnd *cmd) 1259 { 1260 int i, dma_cmd, total, off, dtot; 1261 struct scatterlist *scl; 1262 struct dbdma_cmd *dcmds; 1263 1264 dma_cmd = ms->tgts[ms->conn_tgt].data_goes_out? 1265 OUTPUT_MORE: INPUT_MORE; 1266 dcmds = ms->dma_cmds; 1267 dtot = 0; 1268 if (cmd) { 1269 int nseg; 1270 1271 cmd->SCp.this_residual = scsi_bufflen(cmd); 1272 1273 nseg = scsi_dma_map(cmd); 1274 BUG_ON(nseg < 0); 1275 1276 if (nseg) { 1277 total = 0; 1278 off = ms->data_ptr; 1279 1280 scsi_for_each_sg(cmd, scl, nseg, i) { 1281 u32 dma_addr = sg_dma_address(scl); 1282 u32 dma_len = sg_dma_len(scl); 1283 1284 total += scl->length; 1285 if (off >= dma_len) { 1286 off -= dma_len; 1287 continue; 1288 } 1289 if (dma_len > 0xffff) 1290 panic("mesh: scatterlist element >= 64k"); 1291 dcmds->req_count = cpu_to_le16(dma_len - off); 1292 dcmds->command = cpu_to_le16(dma_cmd); 1293 dcmds->phy_addr = cpu_to_le32(dma_addr + off); 1294 dcmds->xfer_status = 0; 1295 ++dcmds; 1296 dtot += dma_len - off; 1297 off = 0; 1298 } 1299 } 1300 } 1301 if (dtot == 0) { 1302 /* Either the target has overrun our buffer, 1303 or the caller didn't provide a buffer. */ 1304 static char mesh_extra_buf[64]; 1305 1306 dtot = sizeof(mesh_extra_buf); 1307 dcmds->req_count = cpu_to_le16(dtot); 1308 dcmds->phy_addr = cpu_to_le32(virt_to_phys(mesh_extra_buf)); 1309 dcmds->xfer_status = 0; 1310 ++dcmds; 1311 } 1312 dma_cmd += OUTPUT_LAST - OUTPUT_MORE; 1313 dcmds[-1].command = cpu_to_le16(dma_cmd); 1314 memset(dcmds, 0, sizeof(*dcmds)); 1315 dcmds->command = cpu_to_le16(DBDMA_STOP); 1316 ms->dma_count = dtot; 1317 } 1318 1319 static void halt_dma(struct mesh_state *ms) 1320 { 1321 volatile struct dbdma_regs __iomem *md = ms->dma; 1322 volatile struct mesh_regs __iomem *mr = ms->mesh; 1323 struct scsi_cmnd *cmd = ms->current_req; 1324 int t, nb; 1325 1326 if (!ms->tgts[ms->conn_tgt].data_goes_out) { 1327 /* wait a little while until the fifo drains */ 1328 t = 50; 1329 while (t > 0 && in_8(&mr->fifo_count) != 0 1330 && (in_le32(&md->status) & ACTIVE) != 0) { 1331 --t; 1332 udelay(1); 1333 } 1334 } 1335 out_le32(&md->control, RUN << 16); /* turn off RUN bit */ 1336 nb = (mr->count_hi << 8) + mr->count_lo; 1337 dlog(ms, "halt_dma fc/count=%.6x", 1338 MKWORD(0, mr->fifo_count, 0, nb)); 1339 if (ms->tgts[ms->conn_tgt].data_goes_out) 1340 nb += mr->fifo_count; 1341 /* nb is the number of bytes not yet transferred 1342 to/from the target. */ 1343 ms->data_ptr -= nb; 1344 dlog(ms, "data_ptr %x", ms->data_ptr); 1345 if (ms->data_ptr < 0) { 1346 printk(KERN_ERR "mesh: halt_dma: data_ptr=%d (nb=%d, ms=%p)\n", 1347 ms->data_ptr, nb, ms); 1348 ms->data_ptr = 0; 1349 #ifdef MESH_DBG 1350 dumplog(ms, ms->conn_tgt); 1351 dumpslog(ms); 1352 #endif /* MESH_DBG */ 1353 } else if (cmd && scsi_bufflen(cmd) && 1354 ms->data_ptr > scsi_bufflen(cmd)) { 1355 printk(KERN_DEBUG "mesh: target %d overrun, " 1356 "data_ptr=%x total=%x goes_out=%d\n", 1357 ms->conn_tgt, ms->data_ptr, scsi_bufflen(cmd), 1358 ms->tgts[ms->conn_tgt].data_goes_out); 1359 } 1360 scsi_dma_unmap(cmd); 1361 ms->dma_started = 0; 1362 } 1363 1364 static void phase_mismatch(struct mesh_state *ms) 1365 { 1366 volatile struct mesh_regs __iomem *mr = ms->mesh; 1367 int phase; 1368 1369 dlog(ms, "phasemm ch/cl/seq/fc=%.8x", 1370 MKWORD(mr->count_hi, mr->count_lo, mr->sequence, mr->fifo_count)); 1371 phase = in_8(&mr->bus_status0) & BS0_PHASE; 1372 if (ms->msgphase == msg_out_xxx && phase == BP_MSGOUT) { 1373 /* output the last byte of the message, without ATN */ 1374 out_8(&mr->count_lo, 1); 1375 out_8(&mr->sequence, SEQ_MSGOUT + use_active_neg); 1376 mesh_flush_io(mr); 1377 udelay(1); 1378 out_8(&mr->fifo, ms->msgout[ms->n_msgout-1]); 1379 ms->msgphase = msg_out_last; 1380 return; 1381 } 1382 1383 if (ms->msgphase == msg_in) { 1384 get_msgin(ms); 1385 if (ms->n_msgin) 1386 handle_msgin(ms); 1387 } 1388 1389 if (ms->dma_started) 1390 halt_dma(ms); 1391 if (mr->fifo_count) { 1392 out_8(&mr->sequence, SEQ_FLUSHFIFO); 1393 mesh_flush_io(mr); 1394 udelay(1); 1395 } 1396 1397 ms->msgphase = msg_none; 1398 switch (phase) { 1399 case BP_DATAIN: 1400 ms->tgts[ms->conn_tgt].data_goes_out = 0; 1401 ms->phase = dataing; 1402 break; 1403 case BP_DATAOUT: 1404 ms->tgts[ms->conn_tgt].data_goes_out = 1; 1405 ms->phase = dataing; 1406 break; 1407 case BP_COMMAND: 1408 ms->phase = commanding; 1409 break; 1410 case BP_STATUS: 1411 ms->phase = statusing; 1412 break; 1413 case BP_MSGIN: 1414 ms->msgphase = msg_in; 1415 ms->n_msgin = 0; 1416 break; 1417 case BP_MSGOUT: 1418 ms->msgphase = msg_out; 1419 if (ms->n_msgout == 0) { 1420 if (ms->aborting) { 1421 do_abort(ms); 1422 } else { 1423 if (ms->last_n_msgout == 0) { 1424 printk(KERN_DEBUG 1425 "mesh: no msg to repeat\n"); 1426 ms->msgout[0] = NOP; 1427 ms->last_n_msgout = 1; 1428 } 1429 ms->n_msgout = ms->last_n_msgout; 1430 } 1431 } 1432 break; 1433 default: 1434 printk(KERN_DEBUG "mesh: unknown scsi phase %x\n", phase); 1435 ms->stat = DID_ERROR; 1436 mesh_done(ms, 1); 1437 return; 1438 } 1439 1440 start_phase(ms); 1441 } 1442 1443 static void cmd_complete(struct mesh_state *ms) 1444 { 1445 volatile struct mesh_regs __iomem *mr = ms->mesh; 1446 struct scsi_cmnd *cmd = ms->current_req; 1447 struct mesh_target *tp = &ms->tgts[ms->conn_tgt]; 1448 int seq, n, t; 1449 1450 dlog(ms, "cmd_complete fc=%x", mr->fifo_count); 1451 seq = use_active_neg + (ms->n_msgout? SEQ_ATN: 0); 1452 switch (ms->msgphase) { 1453 case msg_out_xxx: 1454 /* huh? we expected a phase mismatch */ 1455 ms->n_msgin = 0; 1456 ms->msgphase = msg_in; 1457 /* fall through */ 1458 1459 case msg_in: 1460 /* should have some message bytes in fifo */ 1461 get_msgin(ms); 1462 n = msgin_length(ms); 1463 if (ms->n_msgin < n) { 1464 out_8(&mr->count_lo, n - ms->n_msgin); 1465 out_8(&mr->sequence, SEQ_MSGIN + seq); 1466 } else { 1467 ms->msgphase = msg_none; 1468 handle_msgin(ms); 1469 start_phase(ms); 1470 } 1471 break; 1472 1473 case msg_in_bad: 1474 out_8(&mr->sequence, SEQ_FLUSHFIFO); 1475 mesh_flush_io(mr); 1476 udelay(1); 1477 out_8(&mr->count_lo, 1); 1478 out_8(&mr->sequence, SEQ_MSGIN + SEQ_ATN + use_active_neg); 1479 break; 1480 1481 case msg_out: 1482 /* 1483 * To get the right timing on ATN wrt ACK, we have 1484 * to get the MESH to drop ACK, wait until REQ gets 1485 * asserted, then drop ATN. To do this we first 1486 * issue a SEQ_MSGOUT with ATN and wait for REQ, 1487 * then change the command to a SEQ_MSGOUT w/o ATN. 1488 * If we don't see REQ in a reasonable time, we 1489 * change the command to SEQ_MSGIN with ATN, 1490 * wait for the phase mismatch interrupt, then 1491 * issue the SEQ_MSGOUT without ATN. 1492 */ 1493 out_8(&mr->count_lo, 1); 1494 out_8(&mr->sequence, SEQ_MSGOUT + use_active_neg + SEQ_ATN); 1495 t = 30; /* wait up to 30us */ 1496 while ((in_8(&mr->bus_status0) & BS0_REQ) == 0 && --t >= 0) 1497 udelay(1); 1498 dlog(ms, "last_mbyte err/exc/fc/cl=%.8x", 1499 MKWORD(mr->error, mr->exception, 1500 mr->fifo_count, mr->count_lo)); 1501 if (in_8(&mr->interrupt) & (INT_ERROR | INT_EXCEPTION)) { 1502 /* whoops, target didn't do what we expected */ 1503 ms->last_n_msgout = ms->n_msgout; 1504 ms->n_msgout = 0; 1505 if (in_8(&mr->interrupt) & INT_ERROR) { 1506 printk(KERN_ERR "mesh: error %x in msg_out\n", 1507 in_8(&mr->error)); 1508 handle_error(ms); 1509 return; 1510 } 1511 if (in_8(&mr->exception) != EXC_PHASEMM) 1512 printk(KERN_ERR "mesh: exc %x in msg_out\n", 1513 in_8(&mr->exception)); 1514 else 1515 printk(KERN_DEBUG "mesh: bs0=%x in msg_out\n", 1516 in_8(&mr->bus_status0)); 1517 handle_exception(ms); 1518 return; 1519 } 1520 if (in_8(&mr->bus_status0) & BS0_REQ) { 1521 out_8(&mr->sequence, SEQ_MSGOUT + use_active_neg); 1522 mesh_flush_io(mr); 1523 udelay(1); 1524 out_8(&mr->fifo, ms->msgout[ms->n_msgout-1]); 1525 ms->msgphase = msg_out_last; 1526 } else { 1527 out_8(&mr->sequence, SEQ_MSGIN + use_active_neg + SEQ_ATN); 1528 ms->msgphase = msg_out_xxx; 1529 } 1530 break; 1531 1532 case msg_out_last: 1533 ms->last_n_msgout = ms->n_msgout; 1534 ms->n_msgout = 0; 1535 ms->msgphase = ms->expect_reply? msg_in: msg_none; 1536 start_phase(ms); 1537 break; 1538 1539 case msg_none: 1540 switch (ms->phase) { 1541 case idle: 1542 printk(KERN_ERR "mesh: interrupt in idle phase?\n"); 1543 dumpslog(ms); 1544 return; 1545 case selecting: 1546 dlog(ms, "Selecting phase at command completion",0); 1547 ms->msgout[0] = IDENTIFY(ALLOW_RESEL(ms->conn_tgt), 1548 (cmd? cmd->device->lun: 0)); 1549 ms->n_msgout = 1; 1550 ms->expect_reply = 0; 1551 if (ms->aborting) { 1552 ms->msgout[0] = ABORT; 1553 ms->n_msgout++; 1554 } else if (tp->sdtr_state == do_sdtr) { 1555 /* add SDTR message */ 1556 add_sdtr_msg(ms); 1557 ms->expect_reply = 1; 1558 tp->sdtr_state = sdtr_sent; 1559 } 1560 ms->msgphase = msg_out; 1561 /* 1562 * We need to wait for REQ before dropping ATN. 1563 * We wait for at most 30us, then fall back to 1564 * a scheme where we issue a SEQ_COMMAND with ATN, 1565 * which will give us a phase mismatch interrupt 1566 * when REQ does come, and then we send the message. 1567 */ 1568 t = 230; /* wait up to 230us */ 1569 while ((in_8(&mr->bus_status0) & BS0_REQ) == 0) { 1570 if (--t < 0) { 1571 dlog(ms, "impatient for req", ms->n_msgout); 1572 ms->msgphase = msg_none; 1573 break; 1574 } 1575 udelay(1); 1576 } 1577 break; 1578 case dataing: 1579 if (ms->dma_count != 0) { 1580 start_phase(ms); 1581 return; 1582 } 1583 /* 1584 * We can get a phase mismatch here if the target 1585 * changes to the status phase, even though we have 1586 * had a command complete interrupt. Then, if we 1587 * issue the SEQ_STATUS command, we'll get a sequence 1588 * error interrupt. Which isn't so bad except that 1589 * occasionally the mesh actually executes the 1590 * SEQ_STATUS *as well as* giving us the sequence 1591 * error and phase mismatch exception. 1592 */ 1593 out_8(&mr->sequence, 0); 1594 out_8(&mr->interrupt, 1595 INT_ERROR | INT_EXCEPTION | INT_CMDDONE); 1596 halt_dma(ms); 1597 break; 1598 case statusing: 1599 if (cmd) { 1600 cmd->SCp.Status = mr->fifo; 1601 if (DEBUG_TARGET(cmd)) 1602 printk(KERN_DEBUG "mesh: status is %x\n", 1603 cmd->SCp.Status); 1604 } 1605 ms->msgphase = msg_in; 1606 break; 1607 case busfreeing: 1608 mesh_done(ms, 1); 1609 return; 1610 case disconnecting: 1611 ms->current_req = NULL; 1612 ms->phase = idle; 1613 mesh_start(ms); 1614 return; 1615 default: 1616 break; 1617 } 1618 ++ms->phase; 1619 start_phase(ms); 1620 break; 1621 } 1622 } 1623 1624 1625 /* 1626 * Called by midlayer with host locked to queue a new 1627 * request 1628 */ 1629 static int mesh_queue_lck(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *)) 1630 { 1631 struct mesh_state *ms; 1632 1633 cmd->scsi_done = done; 1634 cmd->host_scribble = NULL; 1635 1636 ms = (struct mesh_state *) cmd->device->host->hostdata; 1637 1638 if (ms->request_q == NULL) 1639 ms->request_q = cmd; 1640 else 1641 ms->request_qtail->host_scribble = (void *) cmd; 1642 ms->request_qtail = cmd; 1643 1644 if (ms->phase == idle) 1645 mesh_start(ms); 1646 1647 return 0; 1648 } 1649 1650 static DEF_SCSI_QCMD(mesh_queue) 1651 1652 /* 1653 * Called to handle interrupts, either call by the interrupt 1654 * handler (do_mesh_interrupt) or by other functions in 1655 * exceptional circumstances 1656 */ 1657 static void mesh_interrupt(struct mesh_state *ms) 1658 { 1659 volatile struct mesh_regs __iomem *mr = ms->mesh; 1660 int intr; 1661 1662 #if 0 1663 if (ALLOW_DEBUG(ms->conn_tgt)) 1664 printk(KERN_DEBUG "mesh_intr, bs0=%x int=%x exc=%x err=%x " 1665 "phase=%d msgphase=%d\n", mr->bus_status0, 1666 mr->interrupt, mr->exception, mr->error, 1667 ms->phase, ms->msgphase); 1668 #endif 1669 while ((intr = in_8(&mr->interrupt)) != 0) { 1670 dlog(ms, "interrupt intr/err/exc/seq=%.8x", 1671 MKWORD(intr, mr->error, mr->exception, mr->sequence)); 1672 if (intr & INT_ERROR) { 1673 handle_error(ms); 1674 } else if (intr & INT_EXCEPTION) { 1675 handle_exception(ms); 1676 } else if (intr & INT_CMDDONE) { 1677 out_8(&mr->interrupt, INT_CMDDONE); 1678 cmd_complete(ms); 1679 } 1680 } 1681 } 1682 1683 /* Todo: here we can at least try to remove the command from the 1684 * queue if it isn't connected yet, and for pending command, assert 1685 * ATN until the bus gets freed. 1686 */ 1687 static int mesh_abort(struct scsi_cmnd *cmd) 1688 { 1689 struct mesh_state *ms = (struct mesh_state *) cmd->device->host->hostdata; 1690 1691 printk(KERN_DEBUG "mesh_abort(%p)\n", cmd); 1692 mesh_dump_regs(ms); 1693 dumplog(ms, cmd->device->id); 1694 dumpslog(ms); 1695 return FAILED; 1696 } 1697 1698 /* 1699 * Called by the midlayer with the lock held to reset the 1700 * SCSI host and bus. 1701 * The midlayer will wait for devices to come back, we don't need 1702 * to do that ourselves 1703 */ 1704 static int mesh_host_reset(struct scsi_cmnd *cmd) 1705 { 1706 struct mesh_state *ms = (struct mesh_state *) cmd->device->host->hostdata; 1707 volatile struct mesh_regs __iomem *mr = ms->mesh; 1708 volatile struct dbdma_regs __iomem *md = ms->dma; 1709 unsigned long flags; 1710 1711 printk(KERN_DEBUG "mesh_host_reset\n"); 1712 1713 spin_lock_irqsave(ms->host->host_lock, flags); 1714 1715 /* Reset the controller & dbdma channel */ 1716 out_le32(&md->control, (RUN|PAUSE|FLUSH|WAKE) << 16); /* stop dma */ 1717 out_8(&mr->exception, 0xff); /* clear all exception bits */ 1718 out_8(&mr->error, 0xff); /* clear all error bits */ 1719 out_8(&mr->sequence, SEQ_RESETMESH); 1720 mesh_flush_io(mr); 1721 udelay(1); 1722 out_8(&mr->intr_mask, INT_ERROR | INT_EXCEPTION | INT_CMDDONE); 1723 out_8(&mr->source_id, ms->host->this_id); 1724 out_8(&mr->sel_timeout, 25); /* 250ms */ 1725 out_8(&mr->sync_params, ASYNC_PARAMS); 1726 1727 /* Reset the bus */ 1728 out_8(&mr->bus_status1, BS1_RST); /* assert RST */ 1729 mesh_flush_io(mr); 1730 udelay(30); /* leave it on for >= 25us */ 1731 out_8(&mr->bus_status1, 0); /* negate RST */ 1732 1733 /* Complete pending commands */ 1734 handle_reset(ms); 1735 1736 spin_unlock_irqrestore(ms->host->host_lock, flags); 1737 return SUCCESS; 1738 } 1739 1740 static void set_mesh_power(struct mesh_state *ms, int state) 1741 { 1742 if (!machine_is(powermac)) 1743 return; 1744 if (state) { 1745 pmac_call_feature(PMAC_FTR_MESH_ENABLE, macio_get_of_node(ms->mdev), 0, 1); 1746 msleep(200); 1747 } else { 1748 pmac_call_feature(PMAC_FTR_MESH_ENABLE, macio_get_of_node(ms->mdev), 0, 0); 1749 msleep(10); 1750 } 1751 } 1752 1753 1754 #ifdef CONFIG_PM 1755 static int mesh_suspend(struct macio_dev *mdev, pm_message_t mesg) 1756 { 1757 struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev); 1758 unsigned long flags; 1759 1760 switch (mesg.event) { 1761 case PM_EVENT_SUSPEND: 1762 case PM_EVENT_HIBERNATE: 1763 case PM_EVENT_FREEZE: 1764 break; 1765 default: 1766 return 0; 1767 } 1768 if (ms->phase == sleeping) 1769 return 0; 1770 1771 scsi_block_requests(ms->host); 1772 spin_lock_irqsave(ms->host->host_lock, flags); 1773 while(ms->phase != idle) { 1774 spin_unlock_irqrestore(ms->host->host_lock, flags); 1775 msleep(10); 1776 spin_lock_irqsave(ms->host->host_lock, flags); 1777 } 1778 ms->phase = sleeping; 1779 spin_unlock_irqrestore(ms->host->host_lock, flags); 1780 disable_irq(ms->meshintr); 1781 set_mesh_power(ms, 0); 1782 1783 return 0; 1784 } 1785 1786 static int mesh_resume(struct macio_dev *mdev) 1787 { 1788 struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev); 1789 unsigned long flags; 1790 1791 if (ms->phase != sleeping) 1792 return 0; 1793 1794 set_mesh_power(ms, 1); 1795 mesh_init(ms); 1796 spin_lock_irqsave(ms->host->host_lock, flags); 1797 mesh_start(ms); 1798 spin_unlock_irqrestore(ms->host->host_lock, flags); 1799 enable_irq(ms->meshintr); 1800 scsi_unblock_requests(ms->host); 1801 1802 return 0; 1803 } 1804 1805 #endif /* CONFIG_PM */ 1806 1807 /* 1808 * If we leave drives set for synchronous transfers (especially 1809 * CDROMs), and reboot to MacOS, it gets confused, poor thing. 1810 * So, on reboot we reset the SCSI bus. 1811 */ 1812 static int mesh_shutdown(struct macio_dev *mdev) 1813 { 1814 struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev); 1815 volatile struct mesh_regs __iomem *mr; 1816 unsigned long flags; 1817 1818 printk(KERN_INFO "resetting MESH scsi bus(es)\n"); 1819 spin_lock_irqsave(ms->host->host_lock, flags); 1820 mr = ms->mesh; 1821 out_8(&mr->intr_mask, 0); 1822 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE); 1823 out_8(&mr->bus_status1, BS1_RST); 1824 mesh_flush_io(mr); 1825 udelay(30); 1826 out_8(&mr->bus_status1, 0); 1827 spin_unlock_irqrestore(ms->host->host_lock, flags); 1828 1829 return 0; 1830 } 1831 1832 static struct scsi_host_template mesh_template = { 1833 .proc_name = "mesh", 1834 .name = "MESH", 1835 .queuecommand = mesh_queue, 1836 .eh_abort_handler = mesh_abort, 1837 .eh_host_reset_handler = mesh_host_reset, 1838 .can_queue = 20, 1839 .this_id = 7, 1840 .sg_tablesize = SG_ALL, 1841 .cmd_per_lun = 2, 1842 .max_segment_size = 65535, 1843 }; 1844 1845 static int mesh_probe(struct macio_dev *mdev, const struct of_device_id *match) 1846 { 1847 struct device_node *mesh = macio_get_of_node(mdev); 1848 struct pci_dev* pdev = macio_get_pci_dev(mdev); 1849 int tgt, minper; 1850 const int *cfp; 1851 struct mesh_state *ms; 1852 struct Scsi_Host *mesh_host; 1853 void *dma_cmd_space; 1854 dma_addr_t dma_cmd_bus; 1855 1856 switch (mdev->bus->chip->type) { 1857 case macio_heathrow: 1858 case macio_gatwick: 1859 case macio_paddington: 1860 use_active_neg = 0; 1861 break; 1862 default: 1863 use_active_neg = SEQ_ACTIVE_NEG; 1864 } 1865 1866 if (macio_resource_count(mdev) != 2 || macio_irq_count(mdev) != 2) { 1867 printk(KERN_ERR "mesh: expected 2 addrs and 2 intrs" 1868 " (got %d,%d)\n", macio_resource_count(mdev), 1869 macio_irq_count(mdev)); 1870 return -ENODEV; 1871 } 1872 1873 if (macio_request_resources(mdev, "mesh") != 0) { 1874 printk(KERN_ERR "mesh: unable to request memory resources"); 1875 return -EBUSY; 1876 } 1877 mesh_host = scsi_host_alloc(&mesh_template, sizeof(struct mesh_state)); 1878 if (mesh_host == NULL) { 1879 printk(KERN_ERR "mesh: couldn't register host"); 1880 goto out_release; 1881 } 1882 1883 /* Old junk for root discovery, that will die ultimately */ 1884 #if !defined(MODULE) 1885 note_scsi_host(mesh, mesh_host); 1886 #endif 1887 1888 mesh_host->base = macio_resource_start(mdev, 0); 1889 mesh_host->irq = macio_irq(mdev, 0); 1890 ms = (struct mesh_state *) mesh_host->hostdata; 1891 macio_set_drvdata(mdev, ms); 1892 ms->host = mesh_host; 1893 ms->mdev = mdev; 1894 ms->pdev = pdev; 1895 1896 ms->mesh = ioremap(macio_resource_start(mdev, 0), 0x1000); 1897 if (ms->mesh == NULL) { 1898 printk(KERN_ERR "mesh: can't map registers\n"); 1899 goto out_free; 1900 } 1901 ms->dma = ioremap(macio_resource_start(mdev, 1), 0x1000); 1902 if (ms->dma == NULL) { 1903 printk(KERN_ERR "mesh: can't map registers\n"); 1904 iounmap(ms->mesh); 1905 goto out_free; 1906 } 1907 1908 ms->meshintr = macio_irq(mdev, 0); 1909 ms->dmaintr = macio_irq(mdev, 1); 1910 1911 /* Space for dma command list: +1 for stop command, 1912 * +1 to allow for aligning. 1913 */ 1914 ms->dma_cmd_size = (mesh_host->sg_tablesize + 2) * sizeof(struct dbdma_cmd); 1915 1916 /* We use the PCI APIs for now until the generic one gets fixed 1917 * enough or until we get some macio-specific versions 1918 */ 1919 dma_cmd_space = dma_alloc_coherent(&macio_get_pci_dev(mdev)->dev, 1920 ms->dma_cmd_size, &dma_cmd_bus, 1921 GFP_KERNEL); 1922 if (dma_cmd_space == NULL) { 1923 printk(KERN_ERR "mesh: can't allocate DMA table\n"); 1924 goto out_unmap; 1925 } 1926 1927 ms->dma_cmds = (struct dbdma_cmd *) DBDMA_ALIGN(dma_cmd_space); 1928 ms->dma_cmd_space = dma_cmd_space; 1929 ms->dma_cmd_bus = dma_cmd_bus + ((unsigned long)ms->dma_cmds) 1930 - (unsigned long)dma_cmd_space; 1931 ms->current_req = NULL; 1932 for (tgt = 0; tgt < 8; ++tgt) { 1933 ms->tgts[tgt].sdtr_state = do_sdtr; 1934 ms->tgts[tgt].sync_params = ASYNC_PARAMS; 1935 ms->tgts[tgt].current_req = NULL; 1936 } 1937 1938 if ((cfp = of_get_property(mesh, "clock-frequency", NULL))) 1939 ms->clk_freq = *cfp; 1940 else { 1941 printk(KERN_INFO "mesh: assuming 50MHz clock frequency\n"); 1942 ms->clk_freq = 50000000; 1943 } 1944 1945 /* The maximum sync rate is clock / 5; increase 1946 * mesh_sync_period if necessary. 1947 */ 1948 minper = 1000000000 / (ms->clk_freq / 5); /* ns */ 1949 if (mesh_sync_period < minper) 1950 mesh_sync_period = minper; 1951 1952 /* Power up the chip */ 1953 set_mesh_power(ms, 1); 1954 1955 /* Set it up */ 1956 mesh_init(ms); 1957 1958 /* Request interrupt */ 1959 if (request_irq(ms->meshintr, do_mesh_interrupt, 0, "MESH", ms)) { 1960 printk(KERN_ERR "MESH: can't get irq %d\n", ms->meshintr); 1961 goto out_shutdown; 1962 } 1963 1964 /* Add scsi host & scan */ 1965 if (scsi_add_host(mesh_host, &mdev->ofdev.dev)) 1966 goto out_release_irq; 1967 scsi_scan_host(mesh_host); 1968 1969 return 0; 1970 1971 out_release_irq: 1972 free_irq(ms->meshintr, ms); 1973 out_shutdown: 1974 /* shutdown & reset bus in case of error or macos can be confused 1975 * at reboot if the bus was set to synchronous mode already 1976 */ 1977 mesh_shutdown(mdev); 1978 set_mesh_power(ms, 0); 1979 dma_free_coherent(&macio_get_pci_dev(mdev)->dev, ms->dma_cmd_size, 1980 ms->dma_cmd_space, ms->dma_cmd_bus); 1981 out_unmap: 1982 iounmap(ms->dma); 1983 iounmap(ms->mesh); 1984 out_free: 1985 scsi_host_put(mesh_host); 1986 out_release: 1987 macio_release_resources(mdev); 1988 1989 return -ENODEV; 1990 } 1991 1992 static int mesh_remove(struct macio_dev *mdev) 1993 { 1994 struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev); 1995 struct Scsi_Host *mesh_host = ms->host; 1996 1997 scsi_remove_host(mesh_host); 1998 1999 free_irq(ms->meshintr, ms); 2000 2001 /* Reset scsi bus */ 2002 mesh_shutdown(mdev); 2003 2004 /* Shut down chip & termination */ 2005 set_mesh_power(ms, 0); 2006 2007 /* Unmap registers & dma controller */ 2008 iounmap(ms->mesh); 2009 iounmap(ms->dma); 2010 2011 /* Free DMA commands memory */ 2012 dma_free_coherent(&macio_get_pci_dev(mdev)->dev, ms->dma_cmd_size, 2013 ms->dma_cmd_space, ms->dma_cmd_bus); 2014 2015 /* Release memory resources */ 2016 macio_release_resources(mdev); 2017 2018 scsi_host_put(mesh_host); 2019 2020 return 0; 2021 } 2022 2023 2024 static struct of_device_id mesh_match[] = 2025 { 2026 { 2027 .name = "mesh", 2028 }, 2029 { 2030 .type = "scsi", 2031 .compatible = "chrp,mesh0" 2032 }, 2033 {}, 2034 }; 2035 MODULE_DEVICE_TABLE (of, mesh_match); 2036 2037 static struct macio_driver mesh_driver = 2038 { 2039 .driver = { 2040 .name = "mesh", 2041 .owner = THIS_MODULE, 2042 .of_match_table = mesh_match, 2043 }, 2044 .probe = mesh_probe, 2045 .remove = mesh_remove, 2046 .shutdown = mesh_shutdown, 2047 #ifdef CONFIG_PM 2048 .suspend = mesh_suspend, 2049 .resume = mesh_resume, 2050 #endif 2051 }; 2052 2053 2054 static int __init init_mesh(void) 2055 { 2056 2057 /* Calculate sync rate from module parameters */ 2058 if (sync_rate > 10) 2059 sync_rate = 10; 2060 if (sync_rate > 0) { 2061 printk(KERN_INFO "mesh: configured for synchronous %d MB/s\n", sync_rate); 2062 mesh_sync_period = 1000 / sync_rate; /* ns */ 2063 mesh_sync_offset = 15; 2064 } else 2065 printk(KERN_INFO "mesh: configured for asynchronous\n"); 2066 2067 return macio_register_driver(&mesh_driver); 2068 } 2069 2070 static void __exit exit_mesh(void) 2071 { 2072 return macio_unregister_driver(&mesh_driver); 2073 } 2074 2075 module_init(init_mesh); 2076 module_exit(exit_mesh); 2077