1 /************************************************************************** 2 * Initio 9100 device driver for Linux. 3 * 4 * Copyright (c) 1994-1998 Initio Corporation 5 * All rights reserved. 6 * 7 * Cleanups (c) Copyright 2007 Red Hat <alan@lxorguk.ukuu.org.uk> 8 * 9 * This program is free software; you can redistribute it and/or modify 10 * it under the terms of the GNU General Public License as published by 11 * the Free Software Foundation; either version 2, or (at your option) 12 * any later version. 13 * 14 * This program is distributed in the hope that it will be useful, 15 * but WITHOUT ANY WARRANTY; without even the implied warranty of 16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 17 * GNU General Public License for more details. 18 * 19 * You should have received a copy of the GNU General Public License 20 * along with this program; see the file COPYING. If not, write to 21 * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. 22 * 23 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 24 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 25 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 26 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR 27 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 28 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 29 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 30 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 31 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 32 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 33 * SUCH DAMAGE. 34 * 35 **************************************************************************/ 36 37 38 #include <linux/types.h> 39 40 #define TOTAL_SG_ENTRY 32 41 #define MAX_SUPPORTED_ADAPTERS 8 42 #define MAX_OFFSET 15 43 #define MAX_TARGETS 16 44 45 typedef struct { 46 unsigned short base; 47 unsigned short vec; 48 } i91u_config; 49 50 /***************************************/ 51 /* Tulip Configuration Register Set */ 52 /***************************************/ 53 #define TUL_PVID 0x00 /* Vendor ID */ 54 #define TUL_PDID 0x02 /* Device ID */ 55 #define TUL_PCMD 0x04 /* Command */ 56 #define TUL_PSTUS 0x06 /* Status */ 57 #define TUL_PRID 0x08 /* Revision number */ 58 #define TUL_PPI 0x09 /* Programming interface */ 59 #define TUL_PSC 0x0A /* Sub Class */ 60 #define TUL_PBC 0x0B /* Base Class */ 61 #define TUL_PCLS 0x0C /* Cache line size */ 62 #define TUL_PLTR 0x0D /* Latency timer */ 63 #define TUL_PHDT 0x0E /* Header type */ 64 #define TUL_PBIST 0x0F /* BIST */ 65 #define TUL_PBAD 0x10 /* Base address */ 66 #define TUL_PBAD1 0x14 /* Base address */ 67 #define TUL_PBAD2 0x18 /* Base address */ 68 #define TUL_PBAD3 0x1C /* Base address */ 69 #define TUL_PBAD4 0x20 /* Base address */ 70 #define TUL_PBAD5 0x24 /* Base address */ 71 #define TUL_PRSVD 0x28 /* Reserved */ 72 #define TUL_PRSVD1 0x2C /* Reserved */ 73 #define TUL_PRAD 0x30 /* Expansion ROM base address */ 74 #define TUL_PRSVD2 0x34 /* Reserved */ 75 #define TUL_PRSVD3 0x38 /* Reserved */ 76 #define TUL_PINTL 0x3C /* Interrupt line */ 77 #define TUL_PINTP 0x3D /* Interrupt pin */ 78 #define TUL_PIGNT 0x3E /* MIN_GNT */ 79 #define TUL_PMGNT 0x3F /* MAX_GNT */ 80 81 /************************/ 82 /* Jasmin Register Set */ 83 /************************/ 84 #define TUL_HACFG0 0x40 /* H/A Configuration Register 0 */ 85 #define TUL_HACFG1 0x41 /* H/A Configuration Register 1 */ 86 #define TUL_HACFG2 0x42 /* H/A Configuration Register 2 */ 87 88 #define TUL_SDCFG0 0x44 /* SCSI Device Configuration 0 */ 89 #define TUL_SDCFG1 0x45 /* SCSI Device Configuration 1 */ 90 #define TUL_SDCFG2 0x46 /* SCSI Device Configuration 2 */ 91 #define TUL_SDCFG3 0x47 /* SCSI Device Configuration 3 */ 92 93 #define TUL_GINTS 0x50 /* Global Interrupt Status Register */ 94 #define TUL_GIMSK 0x52 /* Global Interrupt MASK Register */ 95 #define TUL_GCTRL 0x54 /* Global Control Register */ 96 #define TUL_GCTRL_EEPROM_BIT 0x04 97 #define TUL_GCTRL1 0x55 /* Global Control Register */ 98 #define TUL_DMACFG 0x5B /* DMA configuration */ 99 #define TUL_NVRAM 0x5D /* Non-volatile RAM port */ 100 101 #define TUL_SCnt0 0x80 /* 00 R/W Transfer Counter Low */ 102 #define TUL_SCnt1 0x81 /* 01 R/W Transfer Counter Mid */ 103 #define TUL_SCnt2 0x82 /* 02 R/W Transfer Count High */ 104 #define TUL_SFifoCnt 0x83 /* 03 R FIFO counter */ 105 #define TUL_SIntEnable 0x84 /* 03 W Interrupt enble */ 106 #define TUL_SInt 0x84 /* 04 R Interrupt Register */ 107 #define TUL_SCtrl0 0x85 /* 05 W Control 0 */ 108 #define TUL_SStatus0 0x85 /* 05 R Status 0 */ 109 #define TUL_SCtrl1 0x86 /* 06 W Control 1 */ 110 #define TUL_SStatus1 0x86 /* 06 R Status 1 */ 111 #define TUL_SConfig 0x87 /* 07 W Configuration */ 112 #define TUL_SStatus2 0x87 /* 07 R Status 2 */ 113 #define TUL_SPeriod 0x88 /* 08 W Sync. Transfer Period & Offset */ 114 #define TUL_SOffset 0x88 /* 08 R Offset */ 115 #define TUL_SScsiId 0x89 /* 09 W SCSI ID */ 116 #define TUL_SBusId 0x89 /* 09 R SCSI BUS ID */ 117 #define TUL_STimeOut 0x8A /* 0A W Sel/Resel Time Out Register */ 118 #define TUL_SIdent 0x8A /* 0A R Identify Message Register */ 119 #define TUL_SAvail 0x8A /* 0A R Available Counter Register */ 120 #define TUL_SData 0x8B /* 0B R/W SCSI data in/out */ 121 #define TUL_SFifo 0x8C /* 0C R/W FIFO */ 122 #define TUL_SSignal 0x90 /* 10 R/W SCSI signal in/out */ 123 #define TUL_SCmd 0x91 /* 11 R/W Command */ 124 #define TUL_STest0 0x92 /* 12 R/W Test0 */ 125 #define TUL_STest1 0x93 /* 13 R/W Test1 */ 126 #define TUL_SCFG1 0x94 /* 14 R/W Configuration */ 127 128 #define TUL_XAddH 0xC0 /*DMA Transfer Physical Address */ 129 #define TUL_XAddW 0xC8 /*DMA Current Transfer Physical Address */ 130 #define TUL_XCntH 0xD0 /*DMA Transfer Counter */ 131 #define TUL_XCntW 0xD4 /*DMA Current Transfer Counter */ 132 #define TUL_XCmd 0xD8 /*DMA Command Register */ 133 #define TUL_Int 0xDC /*Interrupt Register */ 134 #define TUL_XStatus 0xDD /*DMA status Register */ 135 #define TUL_Mask 0xE0 /*Interrupt Mask Register */ 136 #define TUL_XCtrl 0xE4 /*DMA Control Register */ 137 #define TUL_XCtrl1 0xE5 /*DMA Control Register 1 */ 138 #define TUL_XFifo 0xE8 /*DMA FIFO */ 139 140 #define TUL_WCtrl 0xF7 /*Bus master wait state control */ 141 #define TUL_DCtrl 0xFB /*DMA delay control */ 142 143 /*----------------------------------------------------------------------*/ 144 /* bit definition for Command register of Configuration Space Header */ 145 /*----------------------------------------------------------------------*/ 146 #define BUSMS 0x04 /* BUS MASTER Enable */ 147 #define IOSPA 0x01 /* IO Space Enable */ 148 149 /*----------------------------------------------------------------------*/ 150 /* Command Codes of Tulip SCSI Command register */ 151 /*----------------------------------------------------------------------*/ 152 #define TSC_EN_RESEL 0x80 /* Enable Reselection */ 153 #define TSC_CMD_COMP 0x84 /* Command Complete Sequence */ 154 #define TSC_SEL 0x01 /* Select Without ATN Sequence */ 155 #define TSC_SEL_ATN 0x11 /* Select With ATN Sequence */ 156 #define TSC_SEL_ATN_DMA 0x51 /* Select With ATN Sequence with DMA */ 157 #define TSC_SEL_ATN3 0x31 /* Select With ATN3 Sequence */ 158 #define TSC_SEL_ATNSTOP 0x12 /* Select With ATN and Stop Sequence */ 159 #define TSC_SELATNSTOP 0x1E /* Select With ATN and Stop Sequence */ 160 161 #define TSC_SEL_ATN_DIRECT_IN 0x95 /* Select With ATN Sequence */ 162 #define TSC_SEL_ATN_DIRECT_OUT 0x15 /* Select With ATN Sequence */ 163 #define TSC_SEL_ATN3_DIRECT_IN 0xB5 /* Select With ATN3 Sequence */ 164 #define TSC_SEL_ATN3_DIRECT_OUT 0x35 /* Select With ATN3 Sequence */ 165 #define TSC_XF_DMA_OUT_DIRECT 0x06 /* DMA Xfer Information out */ 166 #define TSC_XF_DMA_IN_DIRECT 0x86 /* DMA Xfer Information in */ 167 168 #define TSC_XF_DMA_OUT 0x43 /* DMA Xfer Information out */ 169 #define TSC_XF_DMA_IN 0xC3 /* DMA Xfer Information in */ 170 #define TSC_XF_FIFO_OUT 0x03 /* FIFO Xfer Information out */ 171 #define TSC_XF_FIFO_IN 0x83 /* FIFO Xfer Information in */ 172 173 #define TSC_MSG_ACCEPT 0x0F /* Message Accept */ 174 175 /*----------------------------------------------------------------------*/ 176 /* bit definition for Tulip SCSI Control 0 Register */ 177 /*----------------------------------------------------------------------*/ 178 #define TSC_RST_SEQ 0x20 /* Reset sequence counter */ 179 #define TSC_FLUSH_FIFO 0x10 /* Flush FIFO */ 180 #define TSC_ABT_CMD 0x04 /* Abort command (sequence) */ 181 #define TSC_RST_CHIP 0x02 /* Reset SCSI Chip */ 182 #define TSC_RST_BUS 0x01 /* Reset SCSI Bus */ 183 184 /*----------------------------------------------------------------------*/ 185 /* bit definition for Tulip SCSI Control 1 Register */ 186 /*----------------------------------------------------------------------*/ 187 #define TSC_EN_SCAM 0x80 /* Enable SCAM */ 188 #define TSC_TIMER 0x40 /* Select timeout unit */ 189 #define TSC_EN_SCSI2 0x20 /* SCSI-2 mode */ 190 #define TSC_PWDN 0x10 /* Power down mode */ 191 #define TSC_WIDE_CPU 0x08 /* Wide CPU */ 192 #define TSC_HW_RESELECT 0x04 /* Enable HW reselect */ 193 #define TSC_EN_BUS_OUT 0x02 /* Enable SCSI data bus out latch */ 194 #define TSC_EN_BUS_IN 0x01 /* Enable SCSI data bus in latch */ 195 196 /*----------------------------------------------------------------------*/ 197 /* bit definition for Tulip SCSI Configuration Register */ 198 /*----------------------------------------------------------------------*/ 199 #define TSC_EN_LATCH 0x80 /* Enable phase latch */ 200 #define TSC_INITIATOR 0x40 /* Initiator mode */ 201 #define TSC_EN_SCSI_PAR 0x20 /* Enable SCSI parity */ 202 #define TSC_DMA_8BIT 0x10 /* Alternate dma 8-bits mode */ 203 #define TSC_DMA_16BIT 0x08 /* Alternate dma 16-bits mode */ 204 #define TSC_EN_WDACK 0x04 /* Enable DACK while wide SCSI xfer */ 205 #define TSC_ALT_PERIOD 0x02 /* Alternate sync period mode */ 206 #define TSC_DIS_SCSIRST 0x01 /* Disable SCSI bus reset us */ 207 208 #define TSC_INITDEFAULT (TSC_INITIATOR | TSC_EN_LATCH | TSC_ALT_PERIOD | TSC_DIS_SCSIRST) 209 210 #define TSC_WIDE_SCSI 0x80 /* Enable Wide SCSI */ 211 212 /*----------------------------------------------------------------------*/ 213 /* bit definition for Tulip SCSI signal Register */ 214 /*----------------------------------------------------------------------*/ 215 #define TSC_RST_ACK 0x00 /* Release ACK signal */ 216 #define TSC_RST_ATN 0x00 /* Release ATN signal */ 217 #define TSC_RST_BSY 0x00 /* Release BSY signal */ 218 219 #define TSC_SET_ACK 0x40 /* ACK signal */ 220 #define TSC_SET_ATN 0x08 /* ATN signal */ 221 222 #define TSC_REQI 0x80 /* REQ signal */ 223 #define TSC_ACKI 0x40 /* ACK signal */ 224 #define TSC_BSYI 0x20 /* BSY signal */ 225 #define TSC_SELI 0x10 /* SEL signal */ 226 #define TSC_ATNI 0x08 /* ATN signal */ 227 #define TSC_MSGI 0x04 /* MSG signal */ 228 #define TSC_CDI 0x02 /* C/D signal */ 229 #define TSC_IOI 0x01 /* I/O signal */ 230 231 232 /*----------------------------------------------------------------------*/ 233 /* bit definition for Tulip SCSI Status 0 Register */ 234 /*----------------------------------------------------------------------*/ 235 #define TSS_INT_PENDING 0x80 /* Interrupt pending */ 236 #define TSS_SEQ_ACTIVE 0x40 /* Sequencer active */ 237 #define TSS_XFER_CNT 0x20 /* Transfer counter zero */ 238 #define TSS_FIFO_EMPTY 0x10 /* FIFO empty */ 239 #define TSS_PAR_ERROR 0x08 /* SCSI parity error */ 240 #define TSS_PH_MASK 0x07 /* SCSI phase mask */ 241 242 /*----------------------------------------------------------------------*/ 243 /* bit definition for Tulip SCSI Status 1 Register */ 244 /*----------------------------------------------------------------------*/ 245 #define TSS_STATUS_RCV 0x08 /* Status received */ 246 #define TSS_MSG_SEND 0x40 /* Message sent */ 247 #define TSS_CMD_PH_CMP 0x20 /* command phase done */ 248 #define TSS_DATA_PH_CMP 0x10 /* Data phase done */ 249 #define TSS_STATUS_SEND 0x08 /* Status sent */ 250 #define TSS_XFER_CMP 0x04 /* Transfer completed */ 251 #define TSS_SEL_CMP 0x02 /* Selection completed */ 252 #define TSS_ARB_CMP 0x01 /* Arbitration completed */ 253 254 /*----------------------------------------------------------------------*/ 255 /* bit definition for Tulip SCSI Status 2 Register */ 256 /*----------------------------------------------------------------------*/ 257 #define TSS_CMD_ABTED 0x80 /* Command aborted */ 258 #define TSS_OFFSET_0 0x40 /* Offset counter zero */ 259 #define TSS_FIFO_FULL 0x20 /* FIFO full */ 260 #define TSS_TIMEOUT_0 0x10 /* Timeout counter zero */ 261 #define TSS_BUSY_RLS 0x08 /* Busy release */ 262 #define TSS_PH_MISMATCH 0x04 /* Phase mismatch */ 263 #define TSS_SCSI_BUS_EN 0x02 /* SCSI data bus enable */ 264 #define TSS_SCSIRST 0x01 /* SCSI bus reset in progress */ 265 266 /*----------------------------------------------------------------------*/ 267 /* bit definition for Tulip SCSI Interrupt Register */ 268 /*----------------------------------------------------------------------*/ 269 #define TSS_RESEL_INT 0x80 /* Reselected interrupt */ 270 #define TSS_SEL_TIMEOUT 0x40 /* Selected/reselected timeout */ 271 #define TSS_BUS_SERV 0x20 272 #define TSS_SCSIRST_INT 0x10 /* SCSI bus reset detected */ 273 #define TSS_DISC_INT 0x08 /* Disconnected interrupt */ 274 #define TSS_SEL_INT 0x04 /* Select interrupt */ 275 #define TSS_SCAM_SEL 0x02 /* SCAM selected */ 276 #define TSS_FUNC_COMP 0x01 277 278 /*----------------------------------------------------------------------*/ 279 /* SCSI Phase Codes. */ 280 /*----------------------------------------------------------------------*/ 281 #define DATA_OUT 0 282 #define DATA_IN 1 /* 4 */ 283 #define CMD_OUT 2 284 #define STATUS_IN 3 /* 6 */ 285 #define MSG_OUT 6 /* 3 */ 286 #define MSG_IN 7 287 288 289 290 /*----------------------------------------------------------------------*/ 291 /* Command Codes of Tulip xfer Command register */ 292 /*----------------------------------------------------------------------*/ 293 #define TAX_X_FORC 0x02 294 #define TAX_X_ABT 0x04 295 #define TAX_X_CLR_FIFO 0x08 296 297 #define TAX_X_IN 0x21 298 #define TAX_X_OUT 0x01 299 #define TAX_SG_IN 0xA1 300 #define TAX_SG_OUT 0x81 301 302 /*----------------------------------------------------------------------*/ 303 /* Tulip Interrupt Register */ 304 /*----------------------------------------------------------------------*/ 305 #define XCMP 0x01 306 #define FCMP 0x02 307 #define XABT 0x04 308 #define XERR 0x08 309 #define SCMP 0x10 310 #define IPEND 0x80 311 312 /*----------------------------------------------------------------------*/ 313 /* Tulip DMA Status Register */ 314 /*----------------------------------------------------------------------*/ 315 #define XPEND 0x01 /* Transfer pending */ 316 #define FEMPTY 0x02 /* FIFO empty */ 317 318 319 320 /*----------------------------------------------------------------------*/ 321 /* bit definition for TUL_GCTRL */ 322 /*----------------------------------------------------------------------*/ 323 #define EXTSG 0x80 324 #define EXTAD 0x60 325 #define SEG4K 0x08 326 #define EEPRG 0x04 327 #define MRMUL 0x02 328 329 /*----------------------------------------------------------------------*/ 330 /* bit definition for TUL_NVRAM */ 331 /*----------------------------------------------------------------------*/ 332 #define SE2CS 0x08 333 #define SE2CLK 0x04 334 #define SE2DO 0x02 335 #define SE2DI 0x01 336 337 338 /************************************************************************/ 339 /* Scatter-Gather Element Structure */ 340 /************************************************************************/ 341 struct sg_entry { 342 u32 data; /* Data Pointer */ 343 u32 len; /* Data Length */ 344 }; 345 346 /*********************************************************************** 347 SCSI Control Block 348 ************************************************************************/ 349 struct scsi_ctrl_blk { 350 struct scsi_ctrl_blk *next; 351 u8 status; /*4 */ 352 u8 next_state; /*5 */ 353 u8 mode; /*6 */ 354 u8 msgin; /*7 SCB_Res0 */ 355 u16 sgidx; /*8 */ 356 u16 sgmax; /*A */ 357 #ifdef ALPHA 358 u32 reserved[2]; /*C */ 359 #else 360 u32 reserved[3]; /*C */ 361 #endif 362 363 u32 xferlen; /*18 Current xfer len */ 364 u32 totxlen; /*1C Total xfer len */ 365 u32 paddr; /*20 SCB phy. Addr. */ 366 367 u8 opcode; /*24 SCB command code */ 368 u8 flags; /*25 SCB Flags */ 369 u8 target; /*26 Target Id */ 370 u8 lun; /*27 Lun */ 371 u32 bufptr; /*28 Data Buffer Pointer */ 372 u32 buflen; /*2C Data Allocation Length */ 373 u8 sglen; /*30 SG list # */ 374 u8 senselen; /*31 Sense Allocation Length */ 375 u8 hastat; /*32 */ 376 u8 tastat; /*33 */ 377 u8 cdblen; /*34 CDB Length */ 378 u8 ident; /*35 Identify */ 379 u8 tagmsg; /*36 Tag Message */ 380 u8 tagid; /*37 Queue Tag */ 381 u8 cdb[12]; /*38 */ 382 u32 sgpaddr; /*44 SG List/Sense Buf phy. Addr. */ 383 u32 senseptr; /*48 Sense data pointer */ 384 void (*post) (u8 *, u8 *); /*4C POST routine */ 385 struct scsi_cmnd *srb; /*50 SRB Pointer */ 386 struct sg_entry sglist[TOTAL_SG_ENTRY]; /*54 Start of SG list */ 387 }; 388 389 /* Bit Definition for status */ 390 #define SCB_RENT 0x01 391 #define SCB_PEND 0x02 392 #define SCB_CONTIG 0x04 /* Contingent Allegiance */ 393 #define SCB_SELECT 0x08 394 #define SCB_BUSY 0x10 395 #define SCB_DONE 0x20 396 397 398 /* Opcodes for opcode */ 399 #define ExecSCSI 0x1 400 #define BusDevRst 0x2 401 #define AbortCmd 0x3 402 403 404 /* Bit Definition for mode */ 405 #define SCM_RSENS 0x01 /* request sense mode */ 406 407 408 /* Bit Definition for flags */ 409 #define SCF_DONE 0x01 410 #define SCF_POST 0x02 411 #define SCF_SENSE 0x04 412 #define SCF_DIR 0x18 413 #define SCF_NO_DCHK 0x00 414 #define SCF_DIN 0x08 415 #define SCF_DOUT 0x10 416 #define SCF_NO_XF 0x18 417 #define SCF_WR_VF 0x20 /* Write verify turn on */ 418 #define SCF_POLL 0x40 419 #define SCF_SG 0x80 420 421 /* Error Codes for SCB_HaStat */ 422 #define HOST_SEL_TOUT 0x11 423 #define HOST_DO_DU 0x12 424 #define HOST_BUS_FREE 0x13 425 #define HOST_BAD_PHAS 0x14 426 #define HOST_INV_CMD 0x16 427 #define HOST_ABORTED 0x1A /* 07/21/98 */ 428 #define HOST_SCSI_RST 0x1B 429 #define HOST_DEV_RST 0x1C 430 431 /* Error Codes for SCB_TaStat */ 432 #define TARGET_CHKCOND 0x02 433 #define TARGET_BUSY 0x08 434 #define INI_QUEUE_FULL 0x28 435 436 /*********************************************************************** 437 Target Device Control Structure 438 **********************************************************************/ 439 440 struct target_control { 441 u16 flags; 442 u8 js_period; 443 u8 sconfig0; 444 u16 drv_flags; 445 u8 heads; 446 u8 sectors; 447 }; 448 449 /*********************************************************************** 450 Target Device Control Structure 451 **********************************************************************/ 452 453 /* Bit Definition for TCF_Flags */ 454 #define TCF_SCSI_RATE 0x0007 455 #define TCF_EN_DISC 0x0008 456 #define TCF_NO_SYNC_NEGO 0x0010 457 #define TCF_NO_WDTR 0x0020 458 #define TCF_EN_255 0x0040 459 #define TCF_EN_START 0x0080 460 #define TCF_WDTR_DONE 0x0100 461 #define TCF_SYNC_DONE 0x0200 462 #define TCF_BUSY 0x0400 463 464 465 /* Bit Definition for TCF_DrvFlags */ 466 #define TCF_DRV_BUSY 0x01 /* Indicate target busy(driver) */ 467 #define TCF_DRV_EN_TAG 0x0800 468 #define TCF_DRV_255_63 0x0400 469 470 /*********************************************************************** 471 Host Adapter Control Structure 472 ************************************************************************/ 473 struct initio_host { 474 u16 addr; /* 00 */ 475 u16 bios_addr; /* 02 */ 476 u8 irq; /* 04 */ 477 u8 scsi_id; /* 05 */ 478 u8 max_tar; /* 06 */ 479 u8 num_scbs; /* 07 */ 480 481 u8 flags; /* 08 */ 482 u8 index; /* 09 */ 483 u8 ha_id; /* 0A */ 484 u8 config; /* 0B */ 485 u16 idmask; /* 0C */ 486 u8 semaph; /* 0E */ 487 u8 phase; /* 0F */ 488 u8 jsstatus0; /* 10 */ 489 u8 jsint; /* 11 */ 490 u8 jsstatus1; /* 12 */ 491 u8 sconf1; /* 13 */ 492 493 u8 msg[8]; /* 14 */ 494 struct scsi_ctrl_blk *next_avail; /* 1C */ 495 struct scsi_ctrl_blk *scb; /* 20 */ 496 struct scsi_ctrl_blk *scb_end; /* 24 */ /*UNUSED*/ 497 struct scsi_ctrl_blk *next_pending; /* 28 */ 498 struct scsi_ctrl_blk *next_contig; /* 2C */ /*UNUSED*/ 499 struct scsi_ctrl_blk *active; /* 30 */ 500 struct target_control *active_tc; /* 34 */ 501 502 struct scsi_ctrl_blk *first_avail; /* 38 */ 503 struct scsi_ctrl_blk *last_avail; /* 3C */ 504 struct scsi_ctrl_blk *first_pending; /* 40 */ 505 struct scsi_ctrl_blk *last_pending; /* 44 */ 506 struct scsi_ctrl_blk *first_busy; /* 48 */ 507 struct scsi_ctrl_blk *last_busy; /* 4C */ 508 struct scsi_ctrl_blk *first_done; /* 50 */ 509 struct scsi_ctrl_blk *last_done; /* 54 */ 510 u8 max_tags[16]; /* 58 */ 511 u8 act_tags[16]; /* 68 */ 512 struct target_control targets[MAX_TARGETS]; /* 78 */ 513 spinlock_t avail_lock; 514 spinlock_t semaph_lock; 515 struct pci_dev *pci_dev; 516 }; 517 518 /* Bit Definition for HCB_Config */ 519 #define HCC_SCSI_RESET 0x01 520 #define HCC_EN_PAR 0x02 521 #define HCC_ACT_TERM1 0x04 522 #define HCC_ACT_TERM2 0x08 523 #define HCC_AUTO_TERM 0x10 524 #define HCC_EN_PWR 0x80 525 526 /* Bit Definition for HCB_Flags */ 527 #define HCF_EXPECT_DISC 0x01 528 #define HCF_EXPECT_SELECT 0x02 529 #define HCF_EXPECT_RESET 0x10 530 #define HCF_EXPECT_DONE_DISC 0x20 531 532 /****************************************************************** 533 Serial EEProm 534 *******************************************************************/ 535 536 typedef struct _NVRAM_SCSI { /* SCSI channel configuration */ 537 u8 NVM_ChSCSIID; /* 0Ch -> Channel SCSI ID */ 538 u8 NVM_ChConfig1; /* 0Dh -> Channel config 1 */ 539 u8 NVM_ChConfig2; /* 0Eh -> Channel config 2 */ 540 u8 NVM_NumOfTarg; /* 0Fh -> Number of SCSI target */ 541 /* SCSI target configuration */ 542 u8 NVM_Targ0Config; /* 10h -> Target 0 configuration */ 543 u8 NVM_Targ1Config; /* 11h -> Target 1 configuration */ 544 u8 NVM_Targ2Config; /* 12h -> Target 2 configuration */ 545 u8 NVM_Targ3Config; /* 13h -> Target 3 configuration */ 546 u8 NVM_Targ4Config; /* 14h -> Target 4 configuration */ 547 u8 NVM_Targ5Config; /* 15h -> Target 5 configuration */ 548 u8 NVM_Targ6Config; /* 16h -> Target 6 configuration */ 549 u8 NVM_Targ7Config; /* 17h -> Target 7 configuration */ 550 u8 NVM_Targ8Config; /* 18h -> Target 8 configuration */ 551 u8 NVM_Targ9Config; /* 19h -> Target 9 configuration */ 552 u8 NVM_TargAConfig; /* 1Ah -> Target A configuration */ 553 u8 NVM_TargBConfig; /* 1Bh -> Target B configuration */ 554 u8 NVM_TargCConfig; /* 1Ch -> Target C configuration */ 555 u8 NVM_TargDConfig; /* 1Dh -> Target D configuration */ 556 u8 NVM_TargEConfig; /* 1Eh -> Target E configuration */ 557 u8 NVM_TargFConfig; /* 1Fh -> Target F configuration */ 558 } NVRAM_SCSI; 559 560 typedef struct _NVRAM { 561 /*----------header ---------------*/ 562 u16 NVM_Signature; /* 0,1: Signature */ 563 u8 NVM_Size; /* 2: Size of data structure */ 564 u8 NVM_Revision; /* 3: Revision of data structure */ 565 /* ----Host Adapter Structure ---- */ 566 u8 NVM_ModelByte0; /* 4: Model number (byte 0) */ 567 u8 NVM_ModelByte1; /* 5: Model number (byte 1) */ 568 u8 NVM_ModelInfo; /* 6: Model information */ 569 u8 NVM_NumOfCh; /* 7: Number of SCSI channel */ 570 u8 NVM_BIOSConfig1; /* 8: BIOS configuration 1 */ 571 u8 NVM_BIOSConfig2; /* 9: BIOS configuration 2 */ 572 u8 NVM_HAConfig1; /* A: Hoat adapter configuration 1 */ 573 u8 NVM_HAConfig2; /* B: Hoat adapter configuration 2 */ 574 NVRAM_SCSI NVM_SCSIInfo[2]; 575 u8 NVM_reserved[10]; 576 /* ---------- CheckSum ---------- */ 577 u16 NVM_CheckSum; /* 0x3E, 0x3F: Checksum of NVRam */ 578 } NVRAM, *PNVRAM; 579 580 /* Bios Configuration for nvram->BIOSConfig1 */ 581 #define NBC1_ENABLE 0x01 /* BIOS enable */ 582 #define NBC1_8DRIVE 0x02 /* Support more than 2 drives */ 583 #define NBC1_REMOVABLE 0x04 /* Support removable drive */ 584 #define NBC1_INT19 0x08 /* Intercept int 19h */ 585 #define NBC1_BIOSSCAN 0x10 /* Dynamic BIOS scan */ 586 #define NBC1_LUNSUPPORT 0x40 /* Support LUN */ 587 588 /* HA Configuration Byte 1 */ 589 #define NHC1_BOOTIDMASK 0x0F /* Boot ID number */ 590 #define NHC1_LUNMASK 0x70 /* Boot LUN number */ 591 #define NHC1_CHANMASK 0x80 /* Boot Channel number */ 592 593 /* Bit definition for nvram->SCSIconfig1 */ 594 #define NCC1_BUSRESET 0x01 /* Reset SCSI bus at power up */ 595 #define NCC1_PARITYCHK 0x02 /* SCSI parity enable */ 596 #define NCC1_ACTTERM1 0x04 /* Enable active terminator 1 */ 597 #define NCC1_ACTTERM2 0x08 /* Enable active terminator 2 */ 598 #define NCC1_AUTOTERM 0x10 /* Enable auto terminator */ 599 #define NCC1_PWRMGR 0x80 /* Enable power management */ 600 601 /* Bit definition for SCSI Target configuration byte */ 602 #define NTC_DISCONNECT 0x08 /* Enable SCSI disconnect */ 603 #define NTC_SYNC 0x10 /* SYNC_NEGO */ 604 #define NTC_NO_WDTR 0x20 /* SYNC_NEGO */ 605 #define NTC_1GIGA 0x40 /* 255 head / 63 sectors (64/32) */ 606 #define NTC_SPINUP 0x80 /* Start disk drive */ 607 608 /* Default NVRam values */ 609 #define INI_SIGNATURE 0xC925 610 #define NBC1_DEFAULT (NBC1_ENABLE) 611 #define NCC1_DEFAULT (NCC1_BUSRESET | NCC1_AUTOTERM | NCC1_PARITYCHK) 612 #define NTC_DEFAULT (NTC_NO_WDTR | NTC_1GIGA | NTC_DISCONNECT) 613 614 /* SCSI related definition */ 615 #define DISC_NOT_ALLOW 0x80 /* Disconnect is not allowed */ 616 #define DISC_ALLOW 0xC0 /* Disconnect is allowed */ 617 #define SCSICMD_RequestSense 0x03 618 619 #define SCSI_ABORT_SNOOZE 0 620 #define SCSI_ABORT_SUCCESS 1 621 #define SCSI_ABORT_PENDING 2 622 #define SCSI_ABORT_BUSY 3 623 #define SCSI_ABORT_NOT_RUNNING 4 624 #define SCSI_ABORT_ERROR 5 625 626 #define SCSI_RESET_SNOOZE 0 627 #define SCSI_RESET_PUNT 1 628 #define SCSI_RESET_SUCCESS 2 629 #define SCSI_RESET_PENDING 3 630 #define SCSI_RESET_WAKEUP 4 631 #define SCSI_RESET_NOT_RUNNING 5 632 #define SCSI_RESET_ERROR 6 633 634 #define SCSI_RESET_SYNCHRONOUS 0x01 635 #define SCSI_RESET_ASYNCHRONOUS 0x02 636 #define SCSI_RESET_SUGGEST_BUS_RESET 0x04 637 #define SCSI_RESET_SUGGEST_HOST_RESET 0x08 638 639 #define SCSI_RESET_BUS_RESET 0x100 640 #define SCSI_RESET_HOST_RESET 0x200 641 #define SCSI_RESET_ACTION 0xff 642 643