1 /* 2 * dc395x.c 3 * 4 * Device Driver for Tekram DC395(U/UW/F), DC315(U) 5 * PCI SCSI Bus Master Host Adapter 6 * (SCSI chip set used Tekram ASIC TRM-S1040) 7 * 8 * Authors: 9 * C.L. Huang <ching@tekram.com.tw> 10 * Erich Chen <erich@tekram.com.tw> 11 * (C) Copyright 1995-1999 Tekram Technology Co., Ltd. 12 * 13 * Kurt Garloff <garloff@suse.de> 14 * (C) 1999-2000 Kurt Garloff 15 * 16 * Oliver Neukum <oliver@neukum.name> 17 * Ali Akcaagac <aliakc@web.de> 18 * Jamie Lenehan <lenehan@twibble.org> 19 * (C) 2003 20 * 21 * License: GNU GPL 22 * 23 ************************************************************************* 24 * 25 * Redistribution and use in source and binary forms, with or without 26 * modification, are permitted provided that the following conditions 27 * are met: 28 * 1. Redistributions of source code must retain the above copyright 29 * notice, this list of conditions and the following disclaimer. 30 * 2. Redistributions in binary form must reproduce the above copyright 31 * notice, this list of conditions and the following disclaimer in the 32 * documentation and/or other materials provided with the distribution. 33 * 3. The name of the author may not be used to endorse or promote products 34 * derived from this software without specific prior written permission. 35 * 36 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 37 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 38 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 39 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, 40 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 41 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 42 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 43 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 44 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 45 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 46 * 47 ************************************************************************ 48 */ 49 #include <linux/module.h> 50 #include <linux/moduleparam.h> 51 #include <linux/delay.h> 52 #include <linux/ctype.h> 53 #include <linux/blkdev.h> 54 #include <linux/interrupt.h> 55 #include <linux/init.h> 56 #include <linux/spinlock.h> 57 #include <linux/pci.h> 58 #include <linux/list.h> 59 #include <linux/vmalloc.h> 60 #include <linux/slab.h> 61 #include <asm/io.h> 62 63 #include <scsi/scsi.h> 64 #include <scsi/scsicam.h> /* needed for scsicam_bios_param */ 65 #include <scsi/scsi_cmnd.h> 66 #include <scsi/scsi_device.h> 67 #include <scsi/scsi_host.h> 68 69 #include "dc395x.h" 70 71 #define DC395X_NAME "dc395x" 72 #define DC395X_BANNER "Tekram DC395(U/UW/F), DC315(U) - ASIC TRM-S1040" 73 #define DC395X_VERSION "v2.05, 2004/03/08" 74 75 /*--------------------------------------------------------------------------- 76 Features 77 ---------------------------------------------------------------------------*/ 78 /* 79 * Set to disable parts of the driver 80 */ 81 /*#define DC395x_NO_DISCONNECT*/ 82 /*#define DC395x_NO_TAGQ*/ 83 /*#define DC395x_NO_SYNC*/ 84 /*#define DC395x_NO_WIDE*/ 85 86 /*--------------------------------------------------------------------------- 87 Debugging 88 ---------------------------------------------------------------------------*/ 89 /* 90 * Types of debugging that can be enabled and disabled 91 */ 92 #define DBG_KG 0x0001 93 #define DBG_0 0x0002 94 #define DBG_1 0x0004 95 #define DBG_SG 0x0020 96 #define DBG_FIFO 0x0040 97 #define DBG_PIO 0x0080 98 99 100 /* 101 * Set set of things to output debugging for. 102 * Undefine to remove all debugging 103 */ 104 /*#define DEBUG_MASK (DBG_0|DBG_1|DBG_SG|DBG_FIFO|DBG_PIO)*/ 105 /*#define DEBUG_MASK DBG_0*/ 106 107 108 /* 109 * Output a kernel mesage at the specified level and append the 110 * driver name and a ": " to the start of the message 111 */ 112 #define dprintkl(level, format, arg...) \ 113 printk(level DC395X_NAME ": " format , ## arg) 114 115 116 #ifdef DEBUG_MASK 117 /* 118 * print a debug message - this is formated with KERN_DEBUG, then the 119 * driver name followed by a ": " and then the message is output. 120 * This also checks that the specified debug level is enabled before 121 * outputing the message 122 */ 123 #define dprintkdbg(type, format, arg...) \ 124 do { \ 125 if ((type) & (DEBUG_MASK)) \ 126 dprintkl(KERN_DEBUG , format , ## arg); \ 127 } while (0) 128 129 /* 130 * Check if the specified type of debugging is enabled 131 */ 132 #define debug_enabled(type) ((DEBUG_MASK) & (type)) 133 134 #else 135 /* 136 * No debugging. Do nothing 137 */ 138 #define dprintkdbg(type, format, arg...) \ 139 do {} while (0) 140 #define debug_enabled(type) (0) 141 142 #endif 143 144 145 #ifndef PCI_VENDOR_ID_TEKRAM 146 #define PCI_VENDOR_ID_TEKRAM 0x1DE1 /* Vendor ID */ 147 #endif 148 #ifndef PCI_DEVICE_ID_TEKRAM_TRMS1040 149 #define PCI_DEVICE_ID_TEKRAM_TRMS1040 0x0391 /* Device ID */ 150 #endif 151 152 153 #define DC395x_LOCK_IO(dev,flags) spin_lock_irqsave(((struct Scsi_Host *)dev)->host_lock, flags) 154 #define DC395x_UNLOCK_IO(dev,flags) spin_unlock_irqrestore(((struct Scsi_Host *)dev)->host_lock, flags) 155 156 #define DC395x_read8(acb,address) (u8)(inb(acb->io_port_base + (address))) 157 #define DC395x_read16(acb,address) (u16)(inw(acb->io_port_base + (address))) 158 #define DC395x_read32(acb,address) (u32)(inl(acb->io_port_base + (address))) 159 #define DC395x_write8(acb,address,value) outb((value), acb->io_port_base + (address)) 160 #define DC395x_write16(acb,address,value) outw((value), acb->io_port_base + (address)) 161 #define DC395x_write32(acb,address,value) outl((value), acb->io_port_base + (address)) 162 163 /* cmd->result */ 164 #define RES_TARGET 0x000000FF /* Target State */ 165 #define RES_TARGET_LNX STATUS_MASK /* Only official ... */ 166 #define RES_ENDMSG 0x0000FF00 /* End Message */ 167 #define RES_DID 0x00FF0000 /* DID_ codes */ 168 #define RES_DRV 0xFF000000 /* DRIVER_ codes */ 169 170 #define MK_RES(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt)) 171 #define MK_RES_LNX(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt)<<1) 172 173 #define SET_RES_TARGET(who,tgt) { who &= ~RES_TARGET; who |= (int)(tgt); } 174 #define SET_RES_TARGET_LNX(who,tgt) { who &= ~RES_TARGET_LNX; who |= (int)(tgt) << 1; } 175 #define SET_RES_MSG(who,msg) { who &= ~RES_ENDMSG; who |= (int)(msg) << 8; } 176 #define SET_RES_DID(who,did) { who &= ~RES_DID; who |= (int)(did) << 16; } 177 #define SET_RES_DRV(who,drv) { who &= ~RES_DRV; who |= (int)(drv) << 24; } 178 179 #define TAG_NONE 255 180 181 /* 182 * srb->segement_x is the hw sg list. It is always allocated as a 183 * DC395x_MAX_SG_LISTENTRY entries in a linear block which does not 184 * cross a page boundy. 185 */ 186 #define SEGMENTX_LEN (sizeof(struct SGentry)*DC395x_MAX_SG_LISTENTRY) 187 188 189 struct SGentry { 190 u32 address; /* bus! address */ 191 u32 length; 192 }; 193 194 /* The SEEPROM structure for TRM_S1040 */ 195 struct NVRamTarget { 196 u8 cfg0; /* Target configuration byte 0 */ 197 u8 period; /* Target period */ 198 u8 cfg2; /* Target configuration byte 2 */ 199 u8 cfg3; /* Target configuration byte 3 */ 200 }; 201 202 struct NvRamType { 203 u8 sub_vendor_id[2]; /* 0,1 Sub Vendor ID */ 204 u8 sub_sys_id[2]; /* 2,3 Sub System ID */ 205 u8 sub_class; /* 4 Sub Class */ 206 u8 vendor_id[2]; /* 5,6 Vendor ID */ 207 u8 device_id[2]; /* 7,8 Device ID */ 208 u8 reserved; /* 9 Reserved */ 209 struct NVRamTarget target[DC395x_MAX_SCSI_ID]; 210 /** 10,11,12,13 211 ** 14,15,16,17 212 ** .... 213 ** .... 214 ** 70,71,72,73 215 */ 216 u8 scsi_id; /* 74 Host Adapter SCSI ID */ 217 u8 channel_cfg; /* 75 Channel configuration */ 218 u8 delay_time; /* 76 Power on delay time */ 219 u8 max_tag; /* 77 Maximum tags */ 220 u8 reserved0; /* 78 */ 221 u8 boot_target; /* 79 */ 222 u8 boot_lun; /* 80 */ 223 u8 reserved1; /* 81 */ 224 u16 reserved2[22]; /* 82,..125 */ 225 u16 cksum; /* 126,127 */ 226 }; 227 228 struct ScsiReqBlk { 229 struct list_head list; /* next/prev ptrs for srb lists */ 230 struct DeviceCtlBlk *dcb; 231 struct scsi_cmnd *cmd; 232 233 struct SGentry *segment_x; /* Linear array of hw sg entries (up to 64 entries) */ 234 dma_addr_t sg_bus_addr; /* Bus address of sg list (ie, of segment_x) */ 235 236 u8 sg_count; /* No of HW sg entries for this request */ 237 u8 sg_index; /* Index of HW sg entry for this request */ 238 size_t total_xfer_length; /* Total number of bytes remaining to be transfered */ 239 size_t request_length; /* Total number of bytes in this request */ 240 /* 241 * The sense buffer handling function, request_sense, uses 242 * the first hw sg entry (segment_x[0]) and the transfer 243 * length (total_xfer_length). While doing this it stores the 244 * original values into the last sg hw list 245 * (srb->segment_x[DC395x_MAX_SG_LISTENTRY - 1] and the 246 * total_xfer_length in xferred. These values are restored in 247 * pci_unmap_srb_sense. This is the only place xferred is used. 248 */ 249 size_t xferred; /* Saved copy of total_xfer_length */ 250 251 u16 state; 252 253 u8 msgin_buf[6]; 254 u8 msgout_buf[6]; 255 256 u8 adapter_status; 257 u8 target_status; 258 u8 msg_count; 259 u8 end_message; 260 261 u8 tag_number; 262 u8 status; 263 u8 retry_count; 264 u8 flag; 265 266 u8 scsi_phase; 267 }; 268 269 struct DeviceCtlBlk { 270 struct list_head list; /* next/prev ptrs for the dcb list */ 271 struct AdapterCtlBlk *acb; 272 struct list_head srb_going_list; /* head of going srb list */ 273 struct list_head srb_waiting_list; /* head of waiting srb list */ 274 275 struct ScsiReqBlk *active_srb; 276 u32 tag_mask; 277 278 u16 max_command; 279 280 u8 target_id; /* SCSI Target ID (SCSI Only) */ 281 u8 target_lun; /* SCSI Log. Unit (SCSI Only) */ 282 u8 identify_msg; 283 u8 dev_mode; 284 285 u8 inquiry7; /* To store Inquiry flags */ 286 u8 sync_mode; /* 0:async mode */ 287 u8 min_nego_period; /* for nego. */ 288 u8 sync_period; /* for reg. */ 289 290 u8 sync_offset; /* for reg. and nego.(low nibble) */ 291 u8 flag; 292 u8 dev_type; 293 u8 init_tcq_flag; 294 }; 295 296 struct AdapterCtlBlk { 297 struct Scsi_Host *scsi_host; 298 299 unsigned long io_port_base; 300 unsigned long io_port_len; 301 302 struct list_head dcb_list; /* head of going dcb list */ 303 struct DeviceCtlBlk *dcb_run_robin; 304 struct DeviceCtlBlk *active_dcb; 305 306 struct list_head srb_free_list; /* head of free srb list */ 307 struct ScsiReqBlk *tmp_srb; 308 struct timer_list waiting_timer; 309 struct timer_list selto_timer; 310 311 u16 srb_count; 312 313 u8 sel_timeout; 314 315 unsigned int irq_level; 316 u8 tag_max_num; 317 u8 acb_flag; 318 u8 gmode2; 319 320 u8 config; 321 u8 lun_chk; 322 u8 scan_devices; 323 u8 hostid_bit; 324 325 u8 dcb_map[DC395x_MAX_SCSI_ID]; 326 struct DeviceCtlBlk *children[DC395x_MAX_SCSI_ID][32]; 327 328 struct pci_dev *dev; 329 330 u8 msg_len; 331 332 struct ScsiReqBlk srb_array[DC395x_MAX_SRB_CNT]; 333 struct ScsiReqBlk srb; 334 335 struct NvRamType eeprom; /* eeprom settings for this adapter */ 336 }; 337 338 339 /*--------------------------------------------------------------------------- 340 Forward declarations 341 ---------------------------------------------------------------------------*/ 342 static void data_out_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 343 u16 *pscsi_status); 344 static void data_in_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 345 u16 *pscsi_status); 346 static void command_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 347 u16 *pscsi_status); 348 static void status_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 349 u16 *pscsi_status); 350 static void msgout_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 351 u16 *pscsi_status); 352 static void msgin_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 353 u16 *pscsi_status); 354 static void data_out_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 355 u16 *pscsi_status); 356 static void data_in_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 357 u16 *pscsi_status); 358 static void command_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 359 u16 *pscsi_status); 360 static void status_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 361 u16 *pscsi_status); 362 static void msgout_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 363 u16 *pscsi_status); 364 static void msgin_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 365 u16 *pscsi_status); 366 static void nop0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 367 u16 *pscsi_status); 368 static void nop1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 369 u16 *pscsi_status); 370 static void set_basic_config(struct AdapterCtlBlk *acb); 371 static void cleanup_after_transfer(struct AdapterCtlBlk *acb, 372 struct ScsiReqBlk *srb); 373 static void reset_scsi_bus(struct AdapterCtlBlk *acb); 374 static void data_io_transfer(struct AdapterCtlBlk *acb, 375 struct ScsiReqBlk *srb, u16 io_dir); 376 static void disconnect(struct AdapterCtlBlk *acb); 377 static void reselect(struct AdapterCtlBlk *acb); 378 static u8 start_scsi(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 379 struct ScsiReqBlk *srb); 380 static inline void enable_msgout_abort(struct AdapterCtlBlk *acb, 381 struct ScsiReqBlk *srb); 382 static void build_srb(struct scsi_cmnd *cmd, struct DeviceCtlBlk *dcb, 383 struct ScsiReqBlk *srb); 384 static void doing_srb_done(struct AdapterCtlBlk *acb, u8 did_code, 385 struct scsi_cmnd *cmd, u8 force); 386 static void scsi_reset_detect(struct AdapterCtlBlk *acb); 387 static void pci_unmap_srb(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb); 388 static void pci_unmap_srb_sense(struct AdapterCtlBlk *acb, 389 struct ScsiReqBlk *srb); 390 static void srb_done(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 391 struct ScsiReqBlk *srb); 392 static void request_sense(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 393 struct ScsiReqBlk *srb); 394 static void set_xfer_rate(struct AdapterCtlBlk *acb, 395 struct DeviceCtlBlk *dcb); 396 static void waiting_timeout(unsigned long ptr); 397 398 399 /*--------------------------------------------------------------------------- 400 Static Data 401 ---------------------------------------------------------------------------*/ 402 static u16 current_sync_offset = 0; 403 404 static void *dc395x_scsi_phase0[] = { 405 data_out_phase0,/* phase:0 */ 406 data_in_phase0, /* phase:1 */ 407 command_phase0, /* phase:2 */ 408 status_phase0, /* phase:3 */ 409 nop0, /* phase:4 PH_BUS_FREE .. initial phase */ 410 nop0, /* phase:5 PH_BUS_FREE .. initial phase */ 411 msgout_phase0, /* phase:6 */ 412 msgin_phase0, /* phase:7 */ 413 }; 414 415 static void *dc395x_scsi_phase1[] = { 416 data_out_phase1,/* phase:0 */ 417 data_in_phase1, /* phase:1 */ 418 command_phase1, /* phase:2 */ 419 status_phase1, /* phase:3 */ 420 nop1, /* phase:4 PH_BUS_FREE .. initial phase */ 421 nop1, /* phase:5 PH_BUS_FREE .. initial phase */ 422 msgout_phase1, /* phase:6 */ 423 msgin_phase1, /* phase:7 */ 424 }; 425 426 /* 427 *Fast20: 000 50ns, 20.0 MHz 428 * 001 75ns, 13.3 MHz 429 * 010 100ns, 10.0 MHz 430 * 011 125ns, 8.0 MHz 431 * 100 150ns, 6.6 MHz 432 * 101 175ns, 5.7 MHz 433 * 110 200ns, 5.0 MHz 434 * 111 250ns, 4.0 MHz 435 * 436 *Fast40(LVDS): 000 25ns, 40.0 MHz 437 * 001 50ns, 20.0 MHz 438 * 010 75ns, 13.3 MHz 439 * 011 100ns, 10.0 MHz 440 * 100 125ns, 8.0 MHz 441 * 101 150ns, 6.6 MHz 442 * 110 175ns, 5.7 MHz 443 * 111 200ns, 5.0 MHz 444 */ 445 /*static u8 clock_period[] = {12,19,25,31,37,44,50,62};*/ 446 447 /* real period:48ns,76ns,100ns,124ns,148ns,176ns,200ns,248ns */ 448 static u8 clock_period[] = { 12, 18, 25, 31, 37, 43, 50, 62 }; 449 static u16 clock_speed[] = { 200, 133, 100, 80, 67, 58, 50, 40 }; 450 451 452 /*--------------------------------------------------------------------------- 453 Configuration 454 ---------------------------------------------------------------------------*/ 455 /* 456 * Module/boot parameters currently effect *all* instances of the 457 * card in the system. 458 */ 459 460 /* 461 * Command line parameters are stored in a structure below. 462 * These are the index's into the structure for the various 463 * command line options. 464 */ 465 #define CFG_ADAPTER_ID 0 466 #define CFG_MAX_SPEED 1 467 #define CFG_DEV_MODE 2 468 #define CFG_ADAPTER_MODE 3 469 #define CFG_TAGS 4 470 #define CFG_RESET_DELAY 5 471 472 #define CFG_NUM 6 /* number of configuration items */ 473 474 475 /* 476 * Value used to indicate that a command line override 477 * hasn't been used to modify the value. 478 */ 479 #define CFG_PARAM_UNSET -1 480 481 482 /* 483 * Hold command line parameters. 484 */ 485 struct ParameterData { 486 int value; /* value of this setting */ 487 int min; /* minimum value */ 488 int max; /* maximum value */ 489 int def; /* default value */ 490 int safe; /* safe value */ 491 }; 492 static struct ParameterData __devinitdata cfg_data[] = { 493 { /* adapter id */ 494 CFG_PARAM_UNSET, 495 0, 496 15, 497 7, 498 7 499 }, 500 { /* max speed */ 501 CFG_PARAM_UNSET, 502 0, 503 7, 504 1, /* 13.3Mhz */ 505 4, /* 6.7Hmz */ 506 }, 507 { /* dev mode */ 508 CFG_PARAM_UNSET, 509 0, 510 0x3f, 511 NTC_DO_PARITY_CHK | NTC_DO_DISCONNECT | NTC_DO_SYNC_NEGO | 512 NTC_DO_WIDE_NEGO | NTC_DO_TAG_QUEUEING | 513 NTC_DO_SEND_START, 514 NTC_DO_PARITY_CHK | NTC_DO_SEND_START 515 }, 516 { /* adapter mode */ 517 CFG_PARAM_UNSET, 518 0, 519 0x2f, 520 #ifdef CONFIG_SCSI_MULTI_LUN 521 NAC_SCANLUN | 522 #endif 523 NAC_GT2DRIVES | NAC_GREATER_1G | NAC_POWERON_SCSI_RESET 524 /*| NAC_ACTIVE_NEG*/, 525 NAC_GT2DRIVES | NAC_GREATER_1G | NAC_POWERON_SCSI_RESET | 0x08 526 }, 527 { /* tags */ 528 CFG_PARAM_UNSET, 529 0, 530 5, 531 3, /* 16 tags (??) */ 532 2, 533 }, 534 { /* reset delay */ 535 CFG_PARAM_UNSET, 536 0, 537 180, 538 1, /* 1 second */ 539 10, /* 10 seconds */ 540 } 541 }; 542 543 544 /* 545 * Safe settings. If set to zero the BIOS/default values with 546 * command line overrides will be used. If set to 1 then safe and 547 * slow settings will be used. 548 */ 549 static int use_safe_settings = 0; 550 module_param_named(safe, use_safe_settings, bool, 0); 551 MODULE_PARM_DESC(safe, "Use safe and slow settings only. Default: false"); 552 553 554 module_param_named(adapter_id, cfg_data[CFG_ADAPTER_ID].value, int, 0); 555 MODULE_PARM_DESC(adapter_id, "Adapter SCSI ID. Default 7 (0-15)"); 556 557 module_param_named(max_speed, cfg_data[CFG_MAX_SPEED].value, int, 0); 558 MODULE_PARM_DESC(max_speed, "Maximum bus speed. Default 1 (0-7) Speeds: 0=20, 1=13.3, 2=10, 3=8, 4=6.7, 5=5.8, 6=5, 7=4 Mhz"); 559 560 module_param_named(dev_mode, cfg_data[CFG_DEV_MODE].value, int, 0); 561 MODULE_PARM_DESC(dev_mode, "Device mode."); 562 563 module_param_named(adapter_mode, cfg_data[CFG_ADAPTER_MODE].value, int, 0); 564 MODULE_PARM_DESC(adapter_mode, "Adapter mode."); 565 566 module_param_named(tags, cfg_data[CFG_TAGS].value, int, 0); 567 MODULE_PARM_DESC(tags, "Number of tags (1<<x). Default 3 (0-5)"); 568 569 module_param_named(reset_delay, cfg_data[CFG_RESET_DELAY].value, int, 0); 570 MODULE_PARM_DESC(reset_delay, "Reset delay in seconds. Default 1 (0-180)"); 571 572 573 /** 574 * set_safe_settings - if the use_safe_settings option is set then 575 * set all values to the safe and slow values. 576 **/ 577 static void __devinit set_safe_settings(void) 578 { 579 if (use_safe_settings) 580 { 581 int i; 582 583 dprintkl(KERN_INFO, "Using safe settings.\n"); 584 for (i = 0; i < CFG_NUM; i++) 585 { 586 cfg_data[i].value = cfg_data[i].safe; 587 } 588 } 589 } 590 591 592 /** 593 * fix_settings - reset any boot parameters which are out of range 594 * back to the default values. 595 **/ 596 static void __devinit fix_settings(void) 597 { 598 int i; 599 600 dprintkdbg(DBG_1, 601 "setup: AdapterId=%08x MaxSpeed=%08x DevMode=%08x " 602 "AdapterMode=%08x Tags=%08x ResetDelay=%08x\n", 603 cfg_data[CFG_ADAPTER_ID].value, 604 cfg_data[CFG_MAX_SPEED].value, 605 cfg_data[CFG_DEV_MODE].value, 606 cfg_data[CFG_ADAPTER_MODE].value, 607 cfg_data[CFG_TAGS].value, 608 cfg_data[CFG_RESET_DELAY].value); 609 for (i = 0; i < CFG_NUM; i++) 610 { 611 if (cfg_data[i].value < cfg_data[i].min 612 || cfg_data[i].value > cfg_data[i].max) 613 cfg_data[i].value = cfg_data[i].def; 614 } 615 } 616 617 618 619 /* 620 * Mapping from the eeprom delay index value (index into this array) 621 * to the number of actual seconds that the delay should be for. 622 */ 623 static char __devinitdata eeprom_index_to_delay_map[] = 624 { 1, 3, 5, 10, 16, 30, 60, 120 }; 625 626 627 /** 628 * eeprom_index_to_delay - Take the eeprom delay setting and convert it 629 * into a number of seconds. 630 * 631 * @eeprom: The eeprom structure in which we find the delay index to map. 632 **/ 633 static void __devinit eeprom_index_to_delay(struct NvRamType *eeprom) 634 { 635 eeprom->delay_time = eeprom_index_to_delay_map[eeprom->delay_time]; 636 } 637 638 639 /** 640 * delay_to_eeprom_index - Take a delay in seconds and return the 641 * closest eeprom index which will delay for at least that amount of 642 * seconds. 643 * 644 * @delay: The delay, in seconds, to find the eeprom index for. 645 **/ 646 static int __devinit delay_to_eeprom_index(int delay) 647 { 648 u8 idx = 0; 649 while (idx < 7 && eeprom_index_to_delay_map[idx] < delay) 650 idx++; 651 return idx; 652 } 653 654 655 /** 656 * eeprom_override - Override the eeprom settings, in the provided 657 * eeprom structure, with values that have been set on the command 658 * line. 659 * 660 * @eeprom: The eeprom data to override with command line options. 661 **/ 662 static void __devinit eeprom_override(struct NvRamType *eeprom) 663 { 664 u8 id; 665 666 /* Adapter Settings */ 667 if (cfg_data[CFG_ADAPTER_ID].value != CFG_PARAM_UNSET) 668 eeprom->scsi_id = (u8)cfg_data[CFG_ADAPTER_ID].value; 669 670 if (cfg_data[CFG_ADAPTER_MODE].value != CFG_PARAM_UNSET) 671 eeprom->channel_cfg = (u8)cfg_data[CFG_ADAPTER_MODE].value; 672 673 if (cfg_data[CFG_RESET_DELAY].value != CFG_PARAM_UNSET) 674 eeprom->delay_time = delay_to_eeprom_index( 675 cfg_data[CFG_RESET_DELAY].value); 676 677 if (cfg_data[CFG_TAGS].value != CFG_PARAM_UNSET) 678 eeprom->max_tag = (u8)cfg_data[CFG_TAGS].value; 679 680 /* Device Settings */ 681 for (id = 0; id < DC395x_MAX_SCSI_ID; id++) { 682 if (cfg_data[CFG_DEV_MODE].value != CFG_PARAM_UNSET) 683 eeprom->target[id].cfg0 = 684 (u8)cfg_data[CFG_DEV_MODE].value; 685 686 if (cfg_data[CFG_MAX_SPEED].value != CFG_PARAM_UNSET) 687 eeprom->target[id].period = 688 (u8)cfg_data[CFG_MAX_SPEED].value; 689 690 } 691 } 692 693 694 /*--------------------------------------------------------------------------- 695 ---------------------------------------------------------------------------*/ 696 697 static unsigned int list_size(struct list_head *head) 698 { 699 unsigned int count = 0; 700 struct list_head *pos; 701 list_for_each(pos, head) 702 count++; 703 return count; 704 } 705 706 707 static struct DeviceCtlBlk *dcb_get_next(struct list_head *head, 708 struct DeviceCtlBlk *pos) 709 { 710 int use_next = 0; 711 struct DeviceCtlBlk* next = NULL; 712 struct DeviceCtlBlk* i; 713 714 if (list_empty(head)) 715 return NULL; 716 717 /* find supplied dcb and then select the next one */ 718 list_for_each_entry(i, head, list) 719 if (use_next) { 720 next = i; 721 break; 722 } else if (i == pos) { 723 use_next = 1; 724 } 725 /* if no next one take the head one (ie, wraparound) */ 726 if (!next) 727 list_for_each_entry(i, head, list) { 728 next = i; 729 break; 730 } 731 732 return next; 733 } 734 735 736 static void free_tag(struct DeviceCtlBlk *dcb, struct ScsiReqBlk *srb) 737 { 738 if (srb->tag_number < 255) { 739 dcb->tag_mask &= ~(1 << srb->tag_number); /* free tag mask */ 740 srb->tag_number = 255; 741 } 742 } 743 744 745 /* Find cmd in SRB list */ 746 static inline struct ScsiReqBlk *find_cmd(struct scsi_cmnd *cmd, 747 struct list_head *head) 748 { 749 struct ScsiReqBlk *i; 750 list_for_each_entry(i, head, list) 751 if (i->cmd == cmd) 752 return i; 753 return NULL; 754 } 755 756 757 static struct ScsiReqBlk *srb_get_free(struct AdapterCtlBlk *acb) 758 { 759 struct list_head *head = &acb->srb_free_list; 760 struct ScsiReqBlk *srb = NULL; 761 762 if (!list_empty(head)) { 763 srb = list_entry(head->next, struct ScsiReqBlk, list); 764 list_del(head->next); 765 dprintkdbg(DBG_0, "srb_get_free: srb=%p\n", srb); 766 } 767 return srb; 768 } 769 770 771 static void srb_free_insert(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb) 772 { 773 dprintkdbg(DBG_0, "srb_free_insert: srb=%p\n", srb); 774 list_add_tail(&srb->list, &acb->srb_free_list); 775 } 776 777 778 static void srb_waiting_insert(struct DeviceCtlBlk *dcb, 779 struct ScsiReqBlk *srb) 780 { 781 dprintkdbg(DBG_0, "srb_waiting_insert: (pid#%li) <%02i-%i> srb=%p\n", 782 srb->cmd->serial_number, dcb->target_id, dcb->target_lun, srb); 783 list_add(&srb->list, &dcb->srb_waiting_list); 784 } 785 786 787 static void srb_waiting_append(struct DeviceCtlBlk *dcb, 788 struct ScsiReqBlk *srb) 789 { 790 dprintkdbg(DBG_0, "srb_waiting_append: (pid#%li) <%02i-%i> srb=%p\n", 791 srb->cmd->serial_number, dcb->target_id, dcb->target_lun, srb); 792 list_add_tail(&srb->list, &dcb->srb_waiting_list); 793 } 794 795 796 static void srb_going_append(struct DeviceCtlBlk *dcb, struct ScsiReqBlk *srb) 797 { 798 dprintkdbg(DBG_0, "srb_going_append: (pid#%li) <%02i-%i> srb=%p\n", 799 srb->cmd->serial_number, dcb->target_id, dcb->target_lun, srb); 800 list_add_tail(&srb->list, &dcb->srb_going_list); 801 } 802 803 804 static void srb_going_remove(struct DeviceCtlBlk *dcb, struct ScsiReqBlk *srb) 805 { 806 struct ScsiReqBlk *i; 807 struct ScsiReqBlk *tmp; 808 dprintkdbg(DBG_0, "srb_going_remove: (pid#%li) <%02i-%i> srb=%p\n", 809 srb->cmd->serial_number, dcb->target_id, dcb->target_lun, srb); 810 811 list_for_each_entry_safe(i, tmp, &dcb->srb_going_list, list) 812 if (i == srb) { 813 list_del(&srb->list); 814 break; 815 } 816 } 817 818 819 static void srb_waiting_remove(struct DeviceCtlBlk *dcb, 820 struct ScsiReqBlk *srb) 821 { 822 struct ScsiReqBlk *i; 823 struct ScsiReqBlk *tmp; 824 dprintkdbg(DBG_0, "srb_waiting_remove: (pid#%li) <%02i-%i> srb=%p\n", 825 srb->cmd->serial_number, dcb->target_id, dcb->target_lun, srb); 826 827 list_for_each_entry_safe(i, tmp, &dcb->srb_waiting_list, list) 828 if (i == srb) { 829 list_del(&srb->list); 830 break; 831 } 832 } 833 834 835 static void srb_going_to_waiting_move(struct DeviceCtlBlk *dcb, 836 struct ScsiReqBlk *srb) 837 { 838 dprintkdbg(DBG_0, 839 "srb_going_to_waiting_move: (pid#%li) <%02i-%i> srb=%p\n", 840 srb->cmd->serial_number, dcb->target_id, dcb->target_lun, srb); 841 list_move(&srb->list, &dcb->srb_waiting_list); 842 } 843 844 845 static void srb_waiting_to_going_move(struct DeviceCtlBlk *dcb, 846 struct ScsiReqBlk *srb) 847 { 848 dprintkdbg(DBG_0, 849 "srb_waiting_to_going_move: (pid#%li) <%02i-%i> srb=%p\n", 850 srb->cmd->serial_number, dcb->target_id, dcb->target_lun, srb); 851 list_move(&srb->list, &dcb->srb_going_list); 852 } 853 854 855 /* Sets the timer to wake us up */ 856 static void waiting_set_timer(struct AdapterCtlBlk *acb, unsigned long to) 857 { 858 if (timer_pending(&acb->waiting_timer)) 859 return; 860 init_timer(&acb->waiting_timer); 861 acb->waiting_timer.function = waiting_timeout; 862 acb->waiting_timer.data = (unsigned long) acb; 863 if (time_before(jiffies + to, acb->scsi_host->last_reset - HZ / 2)) 864 acb->waiting_timer.expires = 865 acb->scsi_host->last_reset - HZ / 2 + 1; 866 else 867 acb->waiting_timer.expires = jiffies + to + 1; 868 add_timer(&acb->waiting_timer); 869 } 870 871 872 /* Send the next command from the waiting list to the bus */ 873 static void waiting_process_next(struct AdapterCtlBlk *acb) 874 { 875 struct DeviceCtlBlk *start = NULL; 876 struct DeviceCtlBlk *pos; 877 struct DeviceCtlBlk *dcb; 878 struct ScsiReqBlk *srb; 879 struct list_head *dcb_list_head = &acb->dcb_list; 880 881 if (acb->active_dcb 882 || (acb->acb_flag & (RESET_DETECT + RESET_DONE + RESET_DEV))) 883 return; 884 885 if (timer_pending(&acb->waiting_timer)) 886 del_timer(&acb->waiting_timer); 887 888 if (list_empty(dcb_list_head)) 889 return; 890 891 /* 892 * Find the starting dcb. Need to find it again in the list 893 * since the list may have changed since we set the ptr to it 894 */ 895 list_for_each_entry(dcb, dcb_list_head, list) 896 if (dcb == acb->dcb_run_robin) { 897 start = dcb; 898 break; 899 } 900 if (!start) { 901 /* This can happen! */ 902 start = list_entry(dcb_list_head->next, typeof(*start), list); 903 acb->dcb_run_robin = start; 904 } 905 906 907 /* 908 * Loop over the dcb, but we start somewhere (potentially) in 909 * the middle of the loop so we need to manully do this. 910 */ 911 pos = start; 912 do { 913 struct list_head *waiting_list_head = &pos->srb_waiting_list; 914 915 /* Make sure, the next another device gets scheduled ... */ 916 acb->dcb_run_robin = dcb_get_next(dcb_list_head, 917 acb->dcb_run_robin); 918 919 if (list_empty(waiting_list_head) || 920 pos->max_command <= list_size(&pos->srb_going_list)) { 921 /* move to next dcb */ 922 pos = dcb_get_next(dcb_list_head, pos); 923 } else { 924 srb = list_entry(waiting_list_head->next, 925 struct ScsiReqBlk, list); 926 927 /* Try to send to the bus */ 928 if (!start_scsi(acb, pos, srb)) 929 srb_waiting_to_going_move(pos, srb); 930 else 931 waiting_set_timer(acb, HZ/50); 932 break; 933 } 934 } while (pos != start); 935 } 936 937 938 /* Wake up waiting queue */ 939 static void waiting_timeout(unsigned long ptr) 940 { 941 unsigned long flags; 942 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)ptr; 943 dprintkdbg(DBG_1, 944 "waiting_timeout: Queue woken up by timer. acb=%p\n", acb); 945 DC395x_LOCK_IO(acb->scsi_host, flags); 946 waiting_process_next(acb); 947 DC395x_UNLOCK_IO(acb->scsi_host, flags); 948 } 949 950 951 /* Get the DCB for a given ID/LUN combination */ 952 static struct DeviceCtlBlk *find_dcb(struct AdapterCtlBlk *acb, u8 id, u8 lun) 953 { 954 return acb->children[id][lun]; 955 } 956 957 958 /* Send SCSI Request Block (srb) to adapter (acb) */ 959 static void send_srb(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb) 960 { 961 struct DeviceCtlBlk *dcb = srb->dcb; 962 963 if (dcb->max_command <= list_size(&dcb->srb_going_list) || 964 acb->active_dcb || 965 (acb->acb_flag & (RESET_DETECT + RESET_DONE + RESET_DEV))) { 966 srb_waiting_append(dcb, srb); 967 waiting_process_next(acb); 968 return; 969 } 970 971 if (!start_scsi(acb, dcb, srb)) 972 srb_going_append(dcb, srb); 973 else { 974 srb_waiting_insert(dcb, srb); 975 waiting_set_timer(acb, HZ / 50); 976 } 977 } 978 979 /* Prepare SRB for being sent to Device DCB w/ command *cmd */ 980 static void build_srb(struct scsi_cmnd *cmd, struct DeviceCtlBlk *dcb, 981 struct ScsiReqBlk *srb) 982 { 983 int nseg; 984 enum dma_data_direction dir = cmd->sc_data_direction; 985 dprintkdbg(DBG_0, "build_srb: (pid#%li) <%02i-%i>\n", 986 cmd->serial_number, dcb->target_id, dcb->target_lun); 987 988 srb->dcb = dcb; 989 srb->cmd = cmd; 990 srb->sg_count = 0; 991 srb->total_xfer_length = 0; 992 srb->sg_bus_addr = 0; 993 srb->sg_index = 0; 994 srb->adapter_status = 0; 995 srb->target_status = 0; 996 srb->msg_count = 0; 997 srb->status = 0; 998 srb->flag = 0; 999 srb->state = 0; 1000 srb->retry_count = 0; 1001 srb->tag_number = TAG_NONE; 1002 srb->scsi_phase = PH_BUS_FREE; /* initial phase */ 1003 srb->end_message = 0; 1004 1005 nseg = scsi_dma_map(cmd); 1006 BUG_ON(nseg < 0); 1007 1008 if (dir == PCI_DMA_NONE || !nseg) { 1009 dprintkdbg(DBG_0, 1010 "build_srb: [0] len=%d buf=%p use_sg=%d !MAP=%08x\n", 1011 cmd->bufflen, scsi_sglist(cmd), scsi_sg_count(cmd), 1012 srb->segment_x[0].address); 1013 } else { 1014 int i; 1015 u32 reqlen = scsi_bufflen(cmd); 1016 struct scatterlist *sg; 1017 struct SGentry *sgp = srb->segment_x; 1018 1019 srb->sg_count = nseg; 1020 1021 dprintkdbg(DBG_0, 1022 "build_srb: [n] len=%d buf=%p use_sg=%d segs=%d\n", 1023 reqlen, scsi_sglist(cmd), scsi_sg_count(cmd), 1024 srb->sg_count); 1025 1026 scsi_for_each_sg(cmd, sg, srb->sg_count, i) { 1027 u32 busaddr = (u32)sg_dma_address(sg); 1028 u32 seglen = (u32)sg->length; 1029 sgp[i].address = busaddr; 1030 sgp[i].length = seglen; 1031 srb->total_xfer_length += seglen; 1032 } 1033 sgp += srb->sg_count - 1; 1034 1035 /* 1036 * adjust last page if too big as it is allocated 1037 * on even page boundaries 1038 */ 1039 if (srb->total_xfer_length > reqlen) { 1040 sgp->length -= (srb->total_xfer_length - reqlen); 1041 srb->total_xfer_length = reqlen; 1042 } 1043 1044 /* Fixup for WIDE padding - make sure length is even */ 1045 if (dcb->sync_period & WIDE_SYNC && 1046 srb->total_xfer_length % 2) { 1047 srb->total_xfer_length++; 1048 sgp->length++; 1049 } 1050 1051 srb->sg_bus_addr = pci_map_single(dcb->acb->dev, 1052 srb->segment_x, 1053 SEGMENTX_LEN, 1054 PCI_DMA_TODEVICE); 1055 1056 dprintkdbg(DBG_SG, "build_srb: [n] map sg %p->%08x(%05x)\n", 1057 srb->segment_x, srb->sg_bus_addr, SEGMENTX_LEN); 1058 } 1059 1060 srb->request_length = srb->total_xfer_length; 1061 } 1062 1063 1064 /** 1065 * dc395x_queue_command - queue scsi command passed from the mid 1066 * layer, invoke 'done' on completion 1067 * 1068 * @cmd: pointer to scsi command object 1069 * @done: function pointer to be invoked on completion 1070 * 1071 * Returns 1 if the adapter (host) is busy, else returns 0. One 1072 * reason for an adapter to be busy is that the number 1073 * of outstanding queued commands is already equal to 1074 * struct Scsi_Host::can_queue . 1075 * 1076 * Required: if struct Scsi_Host::can_queue is ever non-zero 1077 * then this function is required. 1078 * 1079 * Locks: struct Scsi_Host::host_lock held on entry (with "irqsave") 1080 * and is expected to be held on return. 1081 * 1082 **/ 1083 static int dc395x_queue_command_lck(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *)) 1084 { 1085 struct DeviceCtlBlk *dcb; 1086 struct ScsiReqBlk *srb; 1087 struct AdapterCtlBlk *acb = 1088 (struct AdapterCtlBlk *)cmd->device->host->hostdata; 1089 dprintkdbg(DBG_0, "queue_command: (pid#%li) <%02i-%i> cmnd=0x%02x\n", 1090 cmd->serial_number, cmd->device->id, cmd->device->lun, cmd->cmnd[0]); 1091 1092 /* Assume BAD_TARGET; will be cleared later */ 1093 cmd->result = DID_BAD_TARGET << 16; 1094 1095 /* ignore invalid targets */ 1096 if (cmd->device->id >= acb->scsi_host->max_id || 1097 cmd->device->lun >= acb->scsi_host->max_lun || 1098 cmd->device->lun >31) { 1099 goto complete; 1100 } 1101 1102 /* does the specified lun on the specified device exist */ 1103 if (!(acb->dcb_map[cmd->device->id] & (1 << cmd->device->lun))) { 1104 dprintkl(KERN_INFO, "queue_command: Ignore target <%02i-%i>\n", 1105 cmd->device->id, cmd->device->lun); 1106 goto complete; 1107 } 1108 1109 /* do we have a DCB for the device */ 1110 dcb = find_dcb(acb, cmd->device->id, cmd->device->lun); 1111 if (!dcb) { 1112 /* should never happen */ 1113 dprintkl(KERN_ERR, "queue_command: No such device <%02i-%i>", 1114 cmd->device->id, cmd->device->lun); 1115 goto complete; 1116 } 1117 1118 /* set callback and clear result in the command */ 1119 cmd->scsi_done = done; 1120 cmd->result = 0; 1121 1122 srb = srb_get_free(acb); 1123 if (!srb) 1124 { 1125 /* 1126 * Return 1 since we are unable to queue this command at this 1127 * point in time. 1128 */ 1129 dprintkdbg(DBG_0, "queue_command: No free srb's\n"); 1130 return 1; 1131 } 1132 1133 build_srb(cmd, dcb, srb); 1134 1135 if (!list_empty(&dcb->srb_waiting_list)) { 1136 /* append to waiting queue */ 1137 srb_waiting_append(dcb, srb); 1138 waiting_process_next(acb); 1139 } else { 1140 /* process immediately */ 1141 send_srb(acb, srb); 1142 } 1143 dprintkdbg(DBG_1, "queue_command: (pid#%li) done\n", cmd->serial_number); 1144 return 0; 1145 1146 complete: 1147 /* 1148 * Complete the command immediatey, and then return 0 to 1149 * indicate that we have handled the command. This is usually 1150 * done when the commad is for things like non existent 1151 * devices. 1152 */ 1153 done(cmd); 1154 return 0; 1155 } 1156 1157 static DEF_SCSI_QCMD(dc395x_queue_command) 1158 1159 /* 1160 * Return the disk geometry for the given SCSI device. 1161 */ 1162 static int dc395x_bios_param(struct scsi_device *sdev, 1163 struct block_device *bdev, sector_t capacity, int *info) 1164 { 1165 #ifdef CONFIG_SCSI_DC395x_TRMS1040_TRADMAP 1166 int heads, sectors, cylinders; 1167 struct AdapterCtlBlk *acb; 1168 int size = capacity; 1169 1170 dprintkdbg(DBG_0, "dc395x_bios_param..............\n"); 1171 acb = (struct AdapterCtlBlk *)sdev->host->hostdata; 1172 heads = 64; 1173 sectors = 32; 1174 cylinders = size / (heads * sectors); 1175 1176 if ((acb->gmode2 & NAC_GREATER_1G) && (cylinders > 1024)) { 1177 heads = 255; 1178 sectors = 63; 1179 cylinders = size / (heads * sectors); 1180 } 1181 geom[0] = heads; 1182 geom[1] = sectors; 1183 geom[2] = cylinders; 1184 return 0; 1185 #else 1186 return scsicam_bios_param(bdev, capacity, info); 1187 #endif 1188 } 1189 1190 1191 static void dump_register_info(struct AdapterCtlBlk *acb, 1192 struct DeviceCtlBlk *dcb, struct ScsiReqBlk *srb) 1193 { 1194 u16 pstat; 1195 struct pci_dev *dev = acb->dev; 1196 pci_read_config_word(dev, PCI_STATUS, &pstat); 1197 if (!dcb) 1198 dcb = acb->active_dcb; 1199 if (!srb && dcb) 1200 srb = dcb->active_srb; 1201 if (srb) { 1202 if (!srb->cmd) 1203 dprintkl(KERN_INFO, "dump: srb=%p cmd=%p OOOPS!\n", 1204 srb, srb->cmd); 1205 else 1206 dprintkl(KERN_INFO, "dump: srb=%p cmd=%p (pid#%li) " 1207 "cmnd=0x%02x <%02i-%i>\n", 1208 srb, srb->cmd, srb->cmd->serial_number, 1209 srb->cmd->cmnd[0], srb->cmd->device->id, 1210 srb->cmd->device->lun); 1211 printk(" sglist=%p cnt=%i idx=%i len=%zu\n", 1212 srb->segment_x, srb->sg_count, srb->sg_index, 1213 srb->total_xfer_length); 1214 printk(" state=0x%04x status=0x%02x phase=0x%02x (%sconn.)\n", 1215 srb->state, srb->status, srb->scsi_phase, 1216 (acb->active_dcb) ? "" : "not"); 1217 } 1218 dprintkl(KERN_INFO, "dump: SCSI{status=0x%04x fifocnt=0x%02x " 1219 "signals=0x%02x irqstat=0x%02x sync=0x%02x target=0x%02x " 1220 "rselid=0x%02x ctr=0x%08x irqen=0x%02x config=0x%04x " 1221 "config2=0x%02x cmd=0x%02x selto=0x%02x}\n", 1222 DC395x_read16(acb, TRM_S1040_SCSI_STATUS), 1223 DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT), 1224 DC395x_read8(acb, TRM_S1040_SCSI_SIGNAL), 1225 DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS), 1226 DC395x_read8(acb, TRM_S1040_SCSI_SYNC), 1227 DC395x_read8(acb, TRM_S1040_SCSI_TARGETID), 1228 DC395x_read8(acb, TRM_S1040_SCSI_IDMSG), 1229 DC395x_read32(acb, TRM_S1040_SCSI_COUNTER), 1230 DC395x_read8(acb, TRM_S1040_SCSI_INTEN), 1231 DC395x_read16(acb, TRM_S1040_SCSI_CONFIG0), 1232 DC395x_read8(acb, TRM_S1040_SCSI_CONFIG2), 1233 DC395x_read8(acb, TRM_S1040_SCSI_COMMAND), 1234 DC395x_read8(acb, TRM_S1040_SCSI_TIMEOUT)); 1235 dprintkl(KERN_INFO, "dump: DMA{cmd=0x%04x fifocnt=0x%02x fstat=0x%02x " 1236 "irqstat=0x%02x irqen=0x%02x cfg=0x%04x tctr=0x%08x " 1237 "ctctr=0x%08x addr=0x%08x:0x%08x}\n", 1238 DC395x_read16(acb, TRM_S1040_DMA_COMMAND), 1239 DC395x_read8(acb, TRM_S1040_DMA_FIFOCNT), 1240 DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT), 1241 DC395x_read8(acb, TRM_S1040_DMA_STATUS), 1242 DC395x_read8(acb, TRM_S1040_DMA_INTEN), 1243 DC395x_read16(acb, TRM_S1040_DMA_CONFIG), 1244 DC395x_read32(acb, TRM_S1040_DMA_XCNT), 1245 DC395x_read32(acb, TRM_S1040_DMA_CXCNT), 1246 DC395x_read32(acb, TRM_S1040_DMA_XHIGHADDR), 1247 DC395x_read32(acb, TRM_S1040_DMA_XLOWADDR)); 1248 dprintkl(KERN_INFO, "dump: gen{gctrl=0x%02x gstat=0x%02x gtmr=0x%02x} " 1249 "pci{status=0x%04x}\n", 1250 DC395x_read8(acb, TRM_S1040_GEN_CONTROL), 1251 DC395x_read8(acb, TRM_S1040_GEN_STATUS), 1252 DC395x_read8(acb, TRM_S1040_GEN_TIMER), 1253 pstat); 1254 } 1255 1256 1257 static inline void clear_fifo(struct AdapterCtlBlk *acb, char *txt) 1258 { 1259 #if debug_enabled(DBG_FIFO) 1260 u8 lines = DC395x_read8(acb, TRM_S1040_SCSI_SIGNAL); 1261 u8 fifocnt = DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT); 1262 if (!(fifocnt & 0x40)) 1263 dprintkdbg(DBG_FIFO, 1264 "clear_fifo: (%i bytes) on phase %02x in %s\n", 1265 fifocnt & 0x3f, lines, txt); 1266 #endif 1267 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_CLRFIFO); 1268 } 1269 1270 1271 static void reset_dev_param(struct AdapterCtlBlk *acb) 1272 { 1273 struct DeviceCtlBlk *dcb; 1274 struct NvRamType *eeprom = &acb->eeprom; 1275 dprintkdbg(DBG_0, "reset_dev_param: acb=%p\n", acb); 1276 1277 list_for_each_entry(dcb, &acb->dcb_list, list) { 1278 u8 period_index; 1279 1280 dcb->sync_mode &= ~(SYNC_NEGO_DONE + WIDE_NEGO_DONE); 1281 dcb->sync_period = 0; 1282 dcb->sync_offset = 0; 1283 1284 dcb->dev_mode = eeprom->target[dcb->target_id].cfg0; 1285 period_index = eeprom->target[dcb->target_id].period & 0x07; 1286 dcb->min_nego_period = clock_period[period_index]; 1287 if (!(dcb->dev_mode & NTC_DO_WIDE_NEGO) 1288 || !(acb->config & HCC_WIDE_CARD)) 1289 dcb->sync_mode &= ~WIDE_NEGO_ENABLE; 1290 } 1291 } 1292 1293 1294 /* 1295 * perform a hard reset on the SCSI bus 1296 * @cmd - some command for this host (for fetching hooks) 1297 * Returns: SUCCESS (0x2002) on success, else FAILED (0x2003). 1298 */ 1299 static int __dc395x_eh_bus_reset(struct scsi_cmnd *cmd) 1300 { 1301 struct AdapterCtlBlk *acb = 1302 (struct AdapterCtlBlk *)cmd->device->host->hostdata; 1303 dprintkl(KERN_INFO, 1304 "eh_bus_reset: (pid#%li) target=<%02i-%i> cmd=%p\n", 1305 cmd->serial_number, cmd->device->id, cmd->device->lun, cmd); 1306 1307 if (timer_pending(&acb->waiting_timer)) 1308 del_timer(&acb->waiting_timer); 1309 1310 /* 1311 * disable interrupt 1312 */ 1313 DC395x_write8(acb, TRM_S1040_DMA_INTEN, 0x00); 1314 DC395x_write8(acb, TRM_S1040_SCSI_INTEN, 0x00); 1315 DC395x_write8(acb, TRM_S1040_SCSI_CONTROL, DO_RSTMODULE); 1316 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, DMARESETMODULE); 1317 1318 reset_scsi_bus(acb); 1319 udelay(500); 1320 1321 /* We may be in serious trouble. Wait some seconds */ 1322 acb->scsi_host->last_reset = 1323 jiffies + 3 * HZ / 2 + 1324 HZ * acb->eeprom.delay_time; 1325 1326 /* 1327 * re-enable interrupt 1328 */ 1329 /* Clear SCSI FIFO */ 1330 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, CLRXFIFO); 1331 clear_fifo(acb, "eh_bus_reset"); 1332 /* Delete pending IRQ */ 1333 DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS); 1334 set_basic_config(acb); 1335 1336 reset_dev_param(acb); 1337 doing_srb_done(acb, DID_RESET, cmd, 0); 1338 acb->active_dcb = NULL; 1339 acb->acb_flag = 0; /* RESET_DETECT, RESET_DONE ,RESET_DEV */ 1340 waiting_process_next(acb); 1341 1342 return SUCCESS; 1343 } 1344 1345 static int dc395x_eh_bus_reset(struct scsi_cmnd *cmd) 1346 { 1347 int rc; 1348 1349 spin_lock_irq(cmd->device->host->host_lock); 1350 rc = __dc395x_eh_bus_reset(cmd); 1351 spin_unlock_irq(cmd->device->host->host_lock); 1352 1353 return rc; 1354 } 1355 1356 /* 1357 * abort an errant SCSI command 1358 * @cmd - command to be aborted 1359 * Returns: SUCCESS (0x2002) on success, else FAILED (0x2003). 1360 */ 1361 static int dc395x_eh_abort(struct scsi_cmnd *cmd) 1362 { 1363 /* 1364 * Look into our command queues: If it has not been sent already, 1365 * we remove it and return success. Otherwise fail. 1366 */ 1367 struct AdapterCtlBlk *acb = 1368 (struct AdapterCtlBlk *)cmd->device->host->hostdata; 1369 struct DeviceCtlBlk *dcb; 1370 struct ScsiReqBlk *srb; 1371 dprintkl(KERN_INFO, "eh_abort: (pid#%li) target=<%02i-%i> cmd=%p\n", 1372 cmd->serial_number, cmd->device->id, cmd->device->lun, cmd); 1373 1374 dcb = find_dcb(acb, cmd->device->id, cmd->device->lun); 1375 if (!dcb) { 1376 dprintkl(KERN_DEBUG, "eh_abort: No such device\n"); 1377 return FAILED; 1378 } 1379 1380 srb = find_cmd(cmd, &dcb->srb_waiting_list); 1381 if (srb) { 1382 srb_waiting_remove(dcb, srb); 1383 pci_unmap_srb_sense(acb, srb); 1384 pci_unmap_srb(acb, srb); 1385 free_tag(dcb, srb); 1386 srb_free_insert(acb, srb); 1387 dprintkl(KERN_DEBUG, "eh_abort: Command was waiting\n"); 1388 cmd->result = DID_ABORT << 16; 1389 return SUCCESS; 1390 } 1391 srb = find_cmd(cmd, &dcb->srb_going_list); 1392 if (srb) { 1393 dprintkl(KERN_DEBUG, "eh_abort: Command in progress\n"); 1394 /* XXX: Should abort the command here */ 1395 } else { 1396 dprintkl(KERN_DEBUG, "eh_abort: Command not found\n"); 1397 } 1398 return FAILED; 1399 } 1400 1401 1402 /* SDTR */ 1403 static void build_sdtr(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 1404 struct ScsiReqBlk *srb) 1405 { 1406 u8 *ptr = srb->msgout_buf + srb->msg_count; 1407 if (srb->msg_count > 1) { 1408 dprintkl(KERN_INFO, 1409 "build_sdtr: msgout_buf BUSY (%i: %02x %02x)\n", 1410 srb->msg_count, srb->msgout_buf[0], 1411 srb->msgout_buf[1]); 1412 return; 1413 } 1414 if (!(dcb->dev_mode & NTC_DO_SYNC_NEGO)) { 1415 dcb->sync_offset = 0; 1416 dcb->min_nego_period = 200 >> 2; 1417 } else if (dcb->sync_offset == 0) 1418 dcb->sync_offset = SYNC_NEGO_OFFSET; 1419 1420 *ptr++ = MSG_EXTENDED; /* (01h) */ 1421 *ptr++ = 3; /* length */ 1422 *ptr++ = EXTENDED_SDTR; /* (01h) */ 1423 *ptr++ = dcb->min_nego_period; /* Transfer period (in 4ns) */ 1424 *ptr++ = dcb->sync_offset; /* Transfer period (max. REQ/ACK dist) */ 1425 srb->msg_count += 5; 1426 srb->state |= SRB_DO_SYNC_NEGO; 1427 } 1428 1429 1430 /* WDTR */ 1431 static void build_wdtr(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 1432 struct ScsiReqBlk *srb) 1433 { 1434 u8 wide = ((dcb->dev_mode & NTC_DO_WIDE_NEGO) & 1435 (acb->config & HCC_WIDE_CARD)) ? 1 : 0; 1436 u8 *ptr = srb->msgout_buf + srb->msg_count; 1437 if (srb->msg_count > 1) { 1438 dprintkl(KERN_INFO, 1439 "build_wdtr: msgout_buf BUSY (%i: %02x %02x)\n", 1440 srb->msg_count, srb->msgout_buf[0], 1441 srb->msgout_buf[1]); 1442 return; 1443 } 1444 *ptr++ = MSG_EXTENDED; /* (01h) */ 1445 *ptr++ = 2; /* length */ 1446 *ptr++ = EXTENDED_WDTR; /* (03h) */ 1447 *ptr++ = wide; 1448 srb->msg_count += 4; 1449 srb->state |= SRB_DO_WIDE_NEGO; 1450 } 1451 1452 1453 #if 0 1454 /* Timer to work around chip flaw: When selecting and the bus is 1455 * busy, we sometimes miss a Selection timeout IRQ */ 1456 void selection_timeout_missed(unsigned long ptr); 1457 /* Sets the timer to wake us up */ 1458 static void selto_timer(struct AdapterCtlBlk *acb) 1459 { 1460 if (timer_pending(&acb->selto_timer)) 1461 return; 1462 acb->selto_timer.function = selection_timeout_missed; 1463 acb->selto_timer.data = (unsigned long) acb; 1464 if (time_before 1465 (jiffies + HZ, acb->scsi_host->last_reset + HZ / 2)) 1466 acb->selto_timer.expires = 1467 acb->scsi_host->last_reset + HZ / 2 + 1; 1468 else 1469 acb->selto_timer.expires = jiffies + HZ + 1; 1470 add_timer(&acb->selto_timer); 1471 } 1472 1473 1474 void selection_timeout_missed(unsigned long ptr) 1475 { 1476 unsigned long flags; 1477 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)ptr; 1478 struct ScsiReqBlk *srb; 1479 dprintkl(KERN_DEBUG, "Chip forgot to produce SelTO IRQ!\n"); 1480 if (!acb->active_dcb || !acb->active_dcb->active_srb) { 1481 dprintkl(KERN_DEBUG, "... but no cmd pending? Oops!\n"); 1482 return; 1483 } 1484 DC395x_LOCK_IO(acb->scsi_host, flags); 1485 srb = acb->active_dcb->active_srb; 1486 disconnect(acb); 1487 DC395x_UNLOCK_IO(acb->scsi_host, flags); 1488 } 1489 #endif 1490 1491 1492 static u8 start_scsi(struct AdapterCtlBlk* acb, struct DeviceCtlBlk* dcb, 1493 struct ScsiReqBlk* srb) 1494 { 1495 u16 s_stat2, return_code; 1496 u8 s_stat, scsicommand, i, identify_message; 1497 u8 *ptr; 1498 dprintkdbg(DBG_0, "start_scsi: (pid#%li) <%02i-%i> srb=%p\n", 1499 srb->cmd->serial_number, dcb->target_id, dcb->target_lun, srb); 1500 1501 srb->tag_number = TAG_NONE; /* acb->tag_max_num: had error read in eeprom */ 1502 1503 s_stat = DC395x_read8(acb, TRM_S1040_SCSI_SIGNAL); 1504 s_stat2 = 0; 1505 s_stat2 = DC395x_read16(acb, TRM_S1040_SCSI_STATUS); 1506 #if 1 1507 if (s_stat & 0x20 /* s_stat2 & 0x02000 */ ) { 1508 dprintkdbg(DBG_KG, "start_scsi: (pid#%li) BUSY %02x %04x\n", 1509 srb->cmd->serial_number, s_stat, s_stat2); 1510 /* 1511 * Try anyway? 1512 * 1513 * We could, BUT: Sometimes the TRM_S1040 misses to produce a Selection 1514 * Timeout, a Disconnect or a Reselection IRQ, so we would be screwed! 1515 * (This is likely to be a bug in the hardware. Obviously, most people 1516 * only have one initiator per SCSI bus.) 1517 * Instead let this fail and have the timer make sure the command is 1518 * tried again after a short time 1519 */ 1520 /*selto_timer (acb); */ 1521 return 1; 1522 } 1523 #endif 1524 if (acb->active_dcb) { 1525 dprintkl(KERN_DEBUG, "start_scsi: (pid#%li) Attempt to start a" 1526 "command while another command (pid#%li) is active.", 1527 srb->cmd->serial_number, 1528 acb->active_dcb->active_srb ? 1529 acb->active_dcb->active_srb->cmd->serial_number : 0); 1530 return 1; 1531 } 1532 if (DC395x_read16(acb, TRM_S1040_SCSI_STATUS) & SCSIINTERRUPT) { 1533 dprintkdbg(DBG_KG, "start_scsi: (pid#%li) Failed (busy)\n", 1534 srb->cmd->serial_number); 1535 return 1; 1536 } 1537 /* Allow starting of SCSI commands half a second before we allow the mid-level 1538 * to queue them again after a reset */ 1539 if (time_before(jiffies, acb->scsi_host->last_reset - HZ / 2)) { 1540 dprintkdbg(DBG_KG, "start_scsi: Refuse cmds (reset wait)\n"); 1541 return 1; 1542 } 1543 1544 /* Flush FIFO */ 1545 clear_fifo(acb, "start_scsi"); 1546 DC395x_write8(acb, TRM_S1040_SCSI_HOSTID, acb->scsi_host->this_id); 1547 DC395x_write8(acb, TRM_S1040_SCSI_TARGETID, dcb->target_id); 1548 DC395x_write8(acb, TRM_S1040_SCSI_SYNC, dcb->sync_period); 1549 DC395x_write8(acb, TRM_S1040_SCSI_OFFSET, dcb->sync_offset); 1550 srb->scsi_phase = PH_BUS_FREE; /* initial phase */ 1551 1552 identify_message = dcb->identify_msg; 1553 /*DC395x_TRM_write8(TRM_S1040_SCSI_IDMSG, identify_message); */ 1554 /* Don't allow disconnection for AUTO_REQSENSE: Cont.All.Cond.! */ 1555 if (srb->flag & AUTO_REQSENSE) 1556 identify_message &= 0xBF; 1557 1558 if (((srb->cmd->cmnd[0] == INQUIRY) 1559 || (srb->cmd->cmnd[0] == REQUEST_SENSE) 1560 || (srb->flag & AUTO_REQSENSE)) 1561 && (((dcb->sync_mode & WIDE_NEGO_ENABLE) 1562 && !(dcb->sync_mode & WIDE_NEGO_DONE)) 1563 || ((dcb->sync_mode & SYNC_NEGO_ENABLE) 1564 && !(dcb->sync_mode & SYNC_NEGO_DONE))) 1565 && (dcb->target_lun == 0)) { 1566 srb->msgout_buf[0] = identify_message; 1567 srb->msg_count = 1; 1568 scsicommand = SCMD_SEL_ATNSTOP; 1569 srb->state = SRB_MSGOUT; 1570 #ifndef SYNC_FIRST 1571 if (dcb->sync_mode & WIDE_NEGO_ENABLE 1572 && dcb->inquiry7 & SCSI_INQ_WBUS16) { 1573 build_wdtr(acb, dcb, srb); 1574 goto no_cmd; 1575 } 1576 #endif 1577 if (dcb->sync_mode & SYNC_NEGO_ENABLE 1578 && dcb->inquiry7 & SCSI_INQ_SYNC) { 1579 build_sdtr(acb, dcb, srb); 1580 goto no_cmd; 1581 } 1582 if (dcb->sync_mode & WIDE_NEGO_ENABLE 1583 && dcb->inquiry7 & SCSI_INQ_WBUS16) { 1584 build_wdtr(acb, dcb, srb); 1585 goto no_cmd; 1586 } 1587 srb->msg_count = 0; 1588 } 1589 /* Send identify message */ 1590 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, identify_message); 1591 1592 scsicommand = SCMD_SEL_ATN; 1593 srb->state = SRB_START_; 1594 #ifndef DC395x_NO_TAGQ 1595 if ((dcb->sync_mode & EN_TAG_QUEUEING) 1596 && (identify_message & 0xC0)) { 1597 /* Send Tag message */ 1598 u32 tag_mask = 1; 1599 u8 tag_number = 0; 1600 while (tag_mask & dcb->tag_mask 1601 && tag_number < dcb->max_command) { 1602 tag_mask = tag_mask << 1; 1603 tag_number++; 1604 } 1605 if (tag_number >= dcb->max_command) { 1606 dprintkl(KERN_WARNING, "start_scsi: (pid#%li) " 1607 "Out of tags target=<%02i-%i>)\n", 1608 srb->cmd->serial_number, srb->cmd->device->id, 1609 srb->cmd->device->lun); 1610 srb->state = SRB_READY; 1611 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, 1612 DO_HWRESELECT); 1613 return 1; 1614 } 1615 /* Send Tag id */ 1616 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, MSG_SIMPLE_QTAG); 1617 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, tag_number); 1618 dcb->tag_mask |= tag_mask; 1619 srb->tag_number = tag_number; 1620 scsicommand = SCMD_SEL_ATN3; 1621 srb->state = SRB_START_; 1622 } 1623 #endif 1624 /*polling:*/ 1625 /* Send CDB ..command block ......... */ 1626 dprintkdbg(DBG_KG, "start_scsi: (pid#%li) <%02i-%i> cmnd=0x%02x tag=%i\n", 1627 srb->cmd->serial_number, srb->cmd->device->id, srb->cmd->device->lun, 1628 srb->cmd->cmnd[0], srb->tag_number); 1629 if (srb->flag & AUTO_REQSENSE) { 1630 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, REQUEST_SENSE); 1631 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, (dcb->target_lun << 5)); 1632 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 1633 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 1634 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, SCSI_SENSE_BUFFERSIZE); 1635 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 1636 } else { 1637 ptr = (u8 *)srb->cmd->cmnd; 1638 for (i = 0; i < srb->cmd->cmd_len; i++) 1639 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, *ptr++); 1640 } 1641 no_cmd: 1642 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, 1643 DO_HWRESELECT | DO_DATALATCH); 1644 if (DC395x_read16(acb, TRM_S1040_SCSI_STATUS) & SCSIINTERRUPT) { 1645 /* 1646 * If start_scsi return 1: 1647 * we caught an interrupt (must be reset or reselection ... ) 1648 * : Let's process it first! 1649 */ 1650 dprintkdbg(DBG_0, "start_scsi: (pid#%li) <%02i-%i> Failed - busy\n", 1651 srb->cmd->serial_number, dcb->target_id, dcb->target_lun); 1652 srb->state = SRB_READY; 1653 free_tag(dcb, srb); 1654 srb->msg_count = 0; 1655 return_code = 1; 1656 /* This IRQ should NOT get lost, as we did not acknowledge it */ 1657 } else { 1658 /* 1659 * If start_scsi returns 0: 1660 * we know that the SCSI processor is free 1661 */ 1662 srb->scsi_phase = PH_BUS_FREE; /* initial phase */ 1663 dcb->active_srb = srb; 1664 acb->active_dcb = dcb; 1665 return_code = 0; 1666 /* it's important for atn stop */ 1667 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, 1668 DO_DATALATCH | DO_HWRESELECT); 1669 /* SCSI command */ 1670 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, scsicommand); 1671 } 1672 return return_code; 1673 } 1674 1675 1676 #define DC395x_ENABLE_MSGOUT \ 1677 DC395x_write16 (acb, TRM_S1040_SCSI_CONTROL, DO_SETATN); \ 1678 srb->state |= SRB_MSGOUT 1679 1680 1681 /* abort command */ 1682 static inline void enable_msgout_abort(struct AdapterCtlBlk *acb, 1683 struct ScsiReqBlk *srb) 1684 { 1685 srb->msgout_buf[0] = ABORT; 1686 srb->msg_count = 1; 1687 DC395x_ENABLE_MSGOUT; 1688 srb->state &= ~SRB_MSGIN; 1689 srb->state |= SRB_MSGOUT; 1690 } 1691 1692 1693 /** 1694 * dc395x_handle_interrupt - Handle an interrupt that has been confirmed to 1695 * have been triggered for this card. 1696 * 1697 * @acb: a pointer to the adpter control block 1698 * @scsi_status: the status return when we checked the card 1699 **/ 1700 static void dc395x_handle_interrupt(struct AdapterCtlBlk *acb, 1701 u16 scsi_status) 1702 { 1703 struct DeviceCtlBlk *dcb; 1704 struct ScsiReqBlk *srb; 1705 u16 phase; 1706 u8 scsi_intstatus; 1707 unsigned long flags; 1708 void (*dc395x_statev)(struct AdapterCtlBlk *, struct ScsiReqBlk *, 1709 u16 *); 1710 1711 DC395x_LOCK_IO(acb->scsi_host, flags); 1712 1713 /* This acknowledges the IRQ */ 1714 scsi_intstatus = DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS); 1715 if ((scsi_status & 0x2007) == 0x2002) 1716 dprintkl(KERN_DEBUG, 1717 "COP after COP completed? %04x\n", scsi_status); 1718 if (debug_enabled(DBG_KG)) { 1719 if (scsi_intstatus & INT_SELTIMEOUT) 1720 dprintkdbg(DBG_KG, "handle_interrupt: Selection timeout\n"); 1721 } 1722 /*dprintkl(KERN_DEBUG, "handle_interrupt: intstatus = 0x%02x ", scsi_intstatus); */ 1723 1724 if (timer_pending(&acb->selto_timer)) 1725 del_timer(&acb->selto_timer); 1726 1727 if (scsi_intstatus & (INT_SELTIMEOUT | INT_DISCONNECT)) { 1728 disconnect(acb); /* bus free interrupt */ 1729 goto out_unlock; 1730 } 1731 if (scsi_intstatus & INT_RESELECTED) { 1732 reselect(acb); 1733 goto out_unlock; 1734 } 1735 if (scsi_intstatus & INT_SELECT) { 1736 dprintkl(KERN_INFO, "Host does not support target mode!\n"); 1737 goto out_unlock; 1738 } 1739 if (scsi_intstatus & INT_SCSIRESET) { 1740 scsi_reset_detect(acb); 1741 goto out_unlock; 1742 } 1743 if (scsi_intstatus & (INT_BUSSERVICE | INT_CMDDONE)) { 1744 dcb = acb->active_dcb; 1745 if (!dcb) { 1746 dprintkl(KERN_DEBUG, 1747 "Oops: BusService (%04x %02x) w/o ActiveDCB!\n", 1748 scsi_status, scsi_intstatus); 1749 goto out_unlock; 1750 } 1751 srb = dcb->active_srb; 1752 if (dcb->flag & ABORT_DEV_) { 1753 dprintkdbg(DBG_0, "MsgOut Abort Device.....\n"); 1754 enable_msgout_abort(acb, srb); 1755 } 1756 1757 /* software sequential machine */ 1758 phase = (u16)srb->scsi_phase; 1759 1760 /* 1761 * 62037 or 62137 1762 * call dc395x_scsi_phase0[]... "phase entry" 1763 * handle every phase before start transfer 1764 */ 1765 /* data_out_phase0, phase:0 */ 1766 /* data_in_phase0, phase:1 */ 1767 /* command_phase0, phase:2 */ 1768 /* status_phase0, phase:3 */ 1769 /* nop0, phase:4 PH_BUS_FREE .. initial phase */ 1770 /* nop0, phase:5 PH_BUS_FREE .. initial phase */ 1771 /* msgout_phase0, phase:6 */ 1772 /* msgin_phase0, phase:7 */ 1773 dc395x_statev = dc395x_scsi_phase0[phase]; 1774 dc395x_statev(acb, srb, &scsi_status); 1775 1776 /* 1777 * if there were any exception occured scsi_status 1778 * will be modify to bus free phase new scsi_status 1779 * transfer out from ... previous dc395x_statev 1780 */ 1781 srb->scsi_phase = scsi_status & PHASEMASK; 1782 phase = (u16)scsi_status & PHASEMASK; 1783 1784 /* 1785 * call dc395x_scsi_phase1[]... "phase entry" handle 1786 * every phase to do transfer 1787 */ 1788 /* data_out_phase1, phase:0 */ 1789 /* data_in_phase1, phase:1 */ 1790 /* command_phase1, phase:2 */ 1791 /* status_phase1, phase:3 */ 1792 /* nop1, phase:4 PH_BUS_FREE .. initial phase */ 1793 /* nop1, phase:5 PH_BUS_FREE .. initial phase */ 1794 /* msgout_phase1, phase:6 */ 1795 /* msgin_phase1, phase:7 */ 1796 dc395x_statev = dc395x_scsi_phase1[phase]; 1797 dc395x_statev(acb, srb, &scsi_status); 1798 } 1799 out_unlock: 1800 DC395x_UNLOCK_IO(acb->scsi_host, flags); 1801 } 1802 1803 1804 static irqreturn_t dc395x_interrupt(int irq, void *dev_id) 1805 { 1806 struct AdapterCtlBlk *acb = dev_id; 1807 u16 scsi_status; 1808 u8 dma_status; 1809 irqreturn_t handled = IRQ_NONE; 1810 1811 /* 1812 * Check for pending interrupt 1813 */ 1814 scsi_status = DC395x_read16(acb, TRM_S1040_SCSI_STATUS); 1815 dma_status = DC395x_read8(acb, TRM_S1040_DMA_STATUS); 1816 if (scsi_status & SCSIINTERRUPT) { 1817 /* interrupt pending - let's process it! */ 1818 dc395x_handle_interrupt(acb, scsi_status); 1819 handled = IRQ_HANDLED; 1820 } 1821 else if (dma_status & 0x20) { 1822 /* Error from the DMA engine */ 1823 dprintkl(KERN_INFO, "Interrupt from DMA engine: 0x%02x!\n", dma_status); 1824 #if 0 1825 dprintkl(KERN_INFO, "This means DMA error! Try to handle ...\n"); 1826 if (acb->active_dcb) { 1827 acb->active_dcb-> flag |= ABORT_DEV_; 1828 if (acb->active_dcb->active_srb) 1829 enable_msgout_abort(acb, acb->active_dcb->active_srb); 1830 } 1831 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, ABORTXFER | CLRXFIFO); 1832 #else 1833 dprintkl(KERN_INFO, "Ignoring DMA error (probably a bad thing) ...\n"); 1834 acb = NULL; 1835 #endif 1836 handled = IRQ_HANDLED; 1837 } 1838 1839 return handled; 1840 } 1841 1842 1843 static void msgout_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 1844 u16 *pscsi_status) 1845 { 1846 dprintkdbg(DBG_0, "msgout_phase0: (pid#%li)\n", srb->cmd->serial_number); 1847 if (srb->state & (SRB_UNEXPECT_RESEL + SRB_ABORT_SENT)) 1848 *pscsi_status = PH_BUS_FREE; /*.. initial phase */ 1849 1850 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 1851 srb->state &= ~SRB_MSGOUT; 1852 } 1853 1854 1855 static void msgout_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 1856 u16 *pscsi_status) 1857 { 1858 u16 i; 1859 u8 *ptr; 1860 dprintkdbg(DBG_0, "msgout_phase1: (pid#%li)\n", srb->cmd->serial_number); 1861 1862 clear_fifo(acb, "msgout_phase1"); 1863 if (!(srb->state & SRB_MSGOUT)) { 1864 srb->state |= SRB_MSGOUT; 1865 dprintkl(KERN_DEBUG, 1866 "msgout_phase1: (pid#%li) Phase unexpected\n", 1867 srb->cmd->serial_number); /* So what ? */ 1868 } 1869 if (!srb->msg_count) { 1870 dprintkdbg(DBG_0, "msgout_phase1: (pid#%li) NOP msg\n", 1871 srb->cmd->serial_number); 1872 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, MSG_NOP); 1873 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 1874 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_FIFO_OUT); 1875 return; 1876 } 1877 ptr = (u8 *)srb->msgout_buf; 1878 for (i = 0; i < srb->msg_count; i++) 1879 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, *ptr++); 1880 srb->msg_count = 0; 1881 if (srb->msgout_buf[0] == MSG_ABORT) 1882 srb->state = SRB_ABORT_SENT; 1883 1884 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_FIFO_OUT); 1885 } 1886 1887 1888 static void command_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 1889 u16 *pscsi_status) 1890 { 1891 dprintkdbg(DBG_0, "command_phase0: (pid#%li)\n", srb->cmd->serial_number); 1892 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); 1893 } 1894 1895 1896 static void command_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 1897 u16 *pscsi_status) 1898 { 1899 struct DeviceCtlBlk *dcb; 1900 u8 *ptr; 1901 u16 i; 1902 dprintkdbg(DBG_0, "command_phase1: (pid#%li)\n", srb->cmd->serial_number); 1903 1904 clear_fifo(acb, "command_phase1"); 1905 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_CLRATN); 1906 if (!(srb->flag & AUTO_REQSENSE)) { 1907 ptr = (u8 *)srb->cmd->cmnd; 1908 for (i = 0; i < srb->cmd->cmd_len; i++) { 1909 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, *ptr); 1910 ptr++; 1911 } 1912 } else { 1913 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, REQUEST_SENSE); 1914 dcb = acb->active_dcb; 1915 /* target id */ 1916 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, (dcb->target_lun << 5)); 1917 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 1918 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 1919 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, SCSI_SENSE_BUFFERSIZE); 1920 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 1921 } 1922 srb->state |= SRB_COMMAND; 1923 /* it's important for atn stop */ 1924 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); 1925 /* SCSI command */ 1926 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_FIFO_OUT); 1927 } 1928 1929 1930 /* 1931 * Verify that the remaining space in the hw sg lists is the same as 1932 * the count of remaining bytes in srb->total_xfer_length 1933 */ 1934 static void sg_verify_length(struct ScsiReqBlk *srb) 1935 { 1936 if (debug_enabled(DBG_SG)) { 1937 unsigned len = 0; 1938 unsigned idx = srb->sg_index; 1939 struct SGentry *psge = srb->segment_x + idx; 1940 for (; idx < srb->sg_count; psge++, idx++) 1941 len += psge->length; 1942 if (len != srb->total_xfer_length) 1943 dprintkdbg(DBG_SG, 1944 "Inconsistent SRB S/G lengths (Tot=%i, Count=%i) !!\n", 1945 srb->total_xfer_length, len); 1946 } 1947 } 1948 1949 1950 /* 1951 * Compute the next Scatter Gather list index and adjust its length 1952 * and address if necessary 1953 */ 1954 static void sg_update_list(struct ScsiReqBlk *srb, u32 left) 1955 { 1956 u8 idx; 1957 u32 xferred = srb->total_xfer_length - left; /* bytes transfered */ 1958 struct SGentry *psge = srb->segment_x + srb->sg_index; 1959 1960 dprintkdbg(DBG_0, 1961 "sg_update_list: Transfered %i of %i bytes, %i remain\n", 1962 xferred, srb->total_xfer_length, left); 1963 if (xferred == 0) { 1964 /* nothing to update since we did not transfer any data */ 1965 return; 1966 } 1967 1968 sg_verify_length(srb); 1969 srb->total_xfer_length = left; /* update remaining count */ 1970 for (idx = srb->sg_index; idx < srb->sg_count; idx++) { 1971 if (xferred >= psge->length) { 1972 /* Complete SG entries done */ 1973 xferred -= psge->length; 1974 } else { 1975 /* Partial SG entry done */ 1976 psge->length -= xferred; 1977 psge->address += xferred; 1978 srb->sg_index = idx; 1979 pci_dma_sync_single_for_device(srb->dcb-> 1980 acb->dev, 1981 srb->sg_bus_addr, 1982 SEGMENTX_LEN, 1983 PCI_DMA_TODEVICE); 1984 break; 1985 } 1986 psge++; 1987 } 1988 sg_verify_length(srb); 1989 } 1990 1991 1992 /* 1993 * We have transfered a single byte (PIO mode?) and need to update 1994 * the count of bytes remaining (total_xfer_length) and update the sg 1995 * entry to either point to next byte in the current sg entry, or of 1996 * already at the end to point to the start of the next sg entry 1997 */ 1998 static void sg_subtract_one(struct ScsiReqBlk *srb) 1999 { 2000 sg_update_list(srb, srb->total_xfer_length - 1); 2001 } 2002 2003 2004 /* 2005 * cleanup_after_transfer 2006 * 2007 * Makes sure, DMA and SCSI engine are empty, after the transfer has finished 2008 * KG: Currently called from StatusPhase1 () 2009 * Should probably also be called from other places 2010 * Best might be to call it in DataXXPhase0, if new phase will differ 2011 */ 2012 static void cleanup_after_transfer(struct AdapterCtlBlk *acb, 2013 struct ScsiReqBlk *srb) 2014 { 2015 /*DC395x_write8 (TRM_S1040_DMA_STATUS, FORCEDMACOMP); */ 2016 if (DC395x_read16(acb, TRM_S1040_DMA_COMMAND) & 0x0001) { /* read */ 2017 if (!(DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT) & 0x40)) 2018 clear_fifo(acb, "cleanup/in"); 2019 if (!(DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT) & 0x80)) 2020 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, CLRXFIFO); 2021 } else { /* write */ 2022 if (!(DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT) & 0x80)) 2023 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, CLRXFIFO); 2024 if (!(DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT) & 0x40)) 2025 clear_fifo(acb, "cleanup/out"); 2026 } 2027 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); 2028 } 2029 2030 2031 /* 2032 * Those no of bytes will be transfered w/ PIO through the SCSI FIFO 2033 * Seems to be needed for unknown reasons; could be a hardware bug :-( 2034 */ 2035 #define DC395x_LASTPIO 4 2036 2037 2038 static void data_out_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2039 u16 *pscsi_status) 2040 { 2041 struct DeviceCtlBlk *dcb = srb->dcb; 2042 u16 scsi_status = *pscsi_status; 2043 u32 d_left_counter = 0; 2044 dprintkdbg(DBG_0, "data_out_phase0: (pid#%li) <%02i-%i>\n", 2045 srb->cmd->serial_number, srb->cmd->device->id, srb->cmd->device->lun); 2046 2047 /* 2048 * KG: We need to drain the buffers before we draw any conclusions! 2049 * This means telling the DMA to push the rest into SCSI, telling 2050 * SCSI to push the rest to the bus. 2051 * However, the device might have been the one to stop us (phase 2052 * change), and the data in transit just needs to be accounted so 2053 * it can be retransmitted.) 2054 */ 2055 /* 2056 * KG: Stop DMA engine pushing more data into the SCSI FIFO 2057 * If we need more data, the DMA SG list will be freshly set up, anyway 2058 */ 2059 dprintkdbg(DBG_PIO, "data_out_phase0: " 2060 "DMA{fifocnt=0x%02x fifostat=0x%02x} " 2061 "SCSI{fifocnt=0x%02x cnt=0x%06x status=0x%04x} total=0x%06x\n", 2062 DC395x_read8(acb, TRM_S1040_DMA_FIFOCNT), 2063 DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT), 2064 DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT), 2065 DC395x_read32(acb, TRM_S1040_SCSI_COUNTER), scsi_status, 2066 srb->total_xfer_length); 2067 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, STOPDMAXFER | CLRXFIFO); 2068 2069 if (!(srb->state & SRB_XFERPAD)) { 2070 if (scsi_status & PARITYERROR) 2071 srb->status |= PARITY_ERROR; 2072 2073 /* 2074 * KG: Right, we can't just rely on the SCSI_COUNTER, because this 2075 * is the no of bytes it got from the DMA engine not the no it 2076 * transferred successfully to the device. (And the difference could 2077 * be as much as the FIFO size, I guess ...) 2078 */ 2079 if (!(scsi_status & SCSIXFERDONE)) { 2080 /* 2081 * when data transfer from DMA FIFO to SCSI FIFO 2082 * if there was some data left in SCSI FIFO 2083 */ 2084 d_left_counter = 2085 (u32)(DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT) & 2086 0x1F); 2087 if (dcb->sync_period & WIDE_SYNC) 2088 d_left_counter <<= 1; 2089 2090 dprintkdbg(DBG_KG, "data_out_phase0: FIFO contains %i %s\n" 2091 "SCSI{fifocnt=0x%02x cnt=0x%08x} " 2092 "DMA{fifocnt=0x%04x cnt=0x%02x ctr=0x%08x}\n", 2093 DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT), 2094 (dcb->sync_period & WIDE_SYNC) ? "words" : "bytes", 2095 DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT), 2096 DC395x_read32(acb, TRM_S1040_SCSI_COUNTER), 2097 DC395x_read8(acb, TRM_S1040_DMA_FIFOCNT), 2098 DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT), 2099 DC395x_read32(acb, TRM_S1040_DMA_CXCNT)); 2100 } 2101 /* 2102 * calculate all the residue data that not yet tranfered 2103 * SCSI transfer counter + left in SCSI FIFO data 2104 * 2105 * .....TRM_S1040_SCSI_COUNTER (24bits) 2106 * The counter always decrement by one for every SCSI byte transfer. 2107 * .....TRM_S1040_SCSI_FIFOCNT ( 5bits) 2108 * The counter is SCSI FIFO offset counter (in units of bytes or! words) 2109 */ 2110 if (srb->total_xfer_length > DC395x_LASTPIO) 2111 d_left_counter += 2112 DC395x_read32(acb, TRM_S1040_SCSI_COUNTER); 2113 2114 /* Is this a good idea? */ 2115 /*clear_fifo(acb, "DOP1"); */ 2116 /* KG: What is this supposed to be useful for? WIDE padding stuff? */ 2117 if (d_left_counter == 1 && dcb->sync_period & WIDE_SYNC 2118 && scsi_bufflen(srb->cmd) % 2) { 2119 d_left_counter = 0; 2120 dprintkl(KERN_INFO, 2121 "data_out_phase0: Discard 1 byte (0x%02x)\n", 2122 scsi_status); 2123 } 2124 /* 2125 * KG: Oops again. Same thinko as above: The SCSI might have been 2126 * faster than the DMA engine, so that it ran out of data. 2127 * In that case, we have to do just nothing! 2128 * But: Why the interrupt: No phase change. No XFERCNT_2_ZERO. Or? 2129 */ 2130 /* 2131 * KG: This is nonsense: We have been WRITING data to the bus 2132 * If the SCSI engine has no bytes left, how should the DMA engine? 2133 */ 2134 if (d_left_counter == 0) { 2135 srb->total_xfer_length = 0; 2136 } else { 2137 /* 2138 * if transfer not yet complete 2139 * there were some data residue in SCSI FIFO or 2140 * SCSI transfer counter not empty 2141 */ 2142 long oldxferred = 2143 srb->total_xfer_length - d_left_counter; 2144 const int diff = 2145 (dcb->sync_period & WIDE_SYNC) ? 2 : 1; 2146 sg_update_list(srb, d_left_counter); 2147 /* KG: Most ugly hack! Apparently, this works around a chip bug */ 2148 if ((srb->segment_x[srb->sg_index].length == 2149 diff && scsi_sg_count(srb->cmd)) 2150 || ((oldxferred & ~PAGE_MASK) == 2151 (PAGE_SIZE - diff)) 2152 ) { 2153 dprintkl(KERN_INFO, "data_out_phase0: " 2154 "Work around chip bug (%i)?\n", diff); 2155 d_left_counter = 2156 srb->total_xfer_length - diff; 2157 sg_update_list(srb, d_left_counter); 2158 /*srb->total_xfer_length -= diff; */ 2159 /*srb->virt_addr += diff; */ 2160 /*if (srb->cmd->use_sg) */ 2161 /* srb->sg_index++; */ 2162 } 2163 } 2164 } 2165 if ((*pscsi_status & PHASEMASK) != PH_DATA_OUT) { 2166 cleanup_after_transfer(acb, srb); 2167 } 2168 } 2169 2170 2171 static void data_out_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2172 u16 *pscsi_status) 2173 { 2174 dprintkdbg(DBG_0, "data_out_phase1: (pid#%li) <%02i-%i>\n", 2175 srb->cmd->serial_number, srb->cmd->device->id, srb->cmd->device->lun); 2176 clear_fifo(acb, "data_out_phase1"); 2177 /* do prepare before transfer when data out phase */ 2178 data_io_transfer(acb, srb, XFERDATAOUT); 2179 } 2180 2181 static void data_in_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2182 u16 *pscsi_status) 2183 { 2184 u16 scsi_status = *pscsi_status; 2185 2186 dprintkdbg(DBG_0, "data_in_phase0: (pid#%li) <%02i-%i>\n", 2187 srb->cmd->serial_number, srb->cmd->device->id, srb->cmd->device->lun); 2188 2189 /* 2190 * KG: DataIn is much more tricky than DataOut. When the device is finished 2191 * and switches to another phase, the SCSI engine should be finished too. 2192 * But: There might still be bytes left in its FIFO to be fetched by the DMA 2193 * engine and transferred to memory. 2194 * We should wait for the FIFOs to be emptied by that (is there any way to 2195 * enforce this?) and then stop the DMA engine, because it might think, that 2196 * there are more bytes to follow. Yes, the device might disconnect prior to 2197 * having all bytes transferred! 2198 * Also we should make sure that all data from the DMA engine buffer's really 2199 * made its way to the system memory! Some documentation on this would not 2200 * seem to be a bad idea, actually. 2201 */ 2202 if (!(srb->state & SRB_XFERPAD)) { 2203 u32 d_left_counter; 2204 unsigned int sc, fc; 2205 2206 if (scsi_status & PARITYERROR) { 2207 dprintkl(KERN_INFO, "data_in_phase0: (pid#%li) " 2208 "Parity Error\n", srb->cmd->serial_number); 2209 srb->status |= PARITY_ERROR; 2210 } 2211 /* 2212 * KG: We should wait for the DMA FIFO to be empty ... 2213 * but: it would be better to wait first for the SCSI FIFO and then the 2214 * the DMA FIFO to become empty? How do we know, that the device not already 2215 * sent data to the FIFO in a MsgIn phase, eg.? 2216 */ 2217 if (!(DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT) & 0x80)) { 2218 #if 0 2219 int ctr = 6000000; 2220 dprintkl(KERN_DEBUG, 2221 "DIP0: Wait for DMA FIFO to flush ...\n"); 2222 /*DC395x_write8 (TRM_S1040_DMA_CONTROL, STOPDMAXFER); */ 2223 /*DC395x_write32 (TRM_S1040_SCSI_COUNTER, 7); */ 2224 /*DC395x_write8 (TRM_S1040_SCSI_COMMAND, SCMD_DMA_IN); */ 2225 while (! 2226 (DC395x_read16(acb, TRM_S1040_DMA_FIFOSTAT) & 2227 0x80) && --ctr); 2228 if (ctr < 6000000 - 1) 2229 dprintkl(KERN_DEBUG 2230 "DIP0: Had to wait for DMA ...\n"); 2231 if (!ctr) 2232 dprintkl(KERN_ERR, 2233 "Deadlock in DIP0 waiting for DMA FIFO empty!!\n"); 2234 /*DC395x_write32 (TRM_S1040_SCSI_COUNTER, 0); */ 2235 #endif 2236 dprintkdbg(DBG_KG, "data_in_phase0: " 2237 "DMA{fifocnt=0x%02x fifostat=0x%02x}\n", 2238 DC395x_read8(acb, TRM_S1040_DMA_FIFOCNT), 2239 DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT)); 2240 } 2241 /* Now: Check remainig data: The SCSI counters should tell us ... */ 2242 sc = DC395x_read32(acb, TRM_S1040_SCSI_COUNTER); 2243 fc = DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT); 2244 d_left_counter = sc + ((fc & 0x1f) 2245 << ((srb->dcb->sync_period & WIDE_SYNC) ? 1 : 2246 0)); 2247 dprintkdbg(DBG_KG, "data_in_phase0: " 2248 "SCSI{fifocnt=0x%02x%s ctr=0x%08x} " 2249 "DMA{fifocnt=0x%02x fifostat=0x%02x ctr=0x%08x} " 2250 "Remain{totxfer=%i scsi_fifo+ctr=%i}\n", 2251 fc, 2252 (srb->dcb->sync_period & WIDE_SYNC) ? "words" : "bytes", 2253 sc, 2254 fc, 2255 DC395x_read8(acb, TRM_S1040_DMA_FIFOSTAT), 2256 DC395x_read32(acb, TRM_S1040_DMA_CXCNT), 2257 srb->total_xfer_length, d_left_counter); 2258 #if DC395x_LASTPIO 2259 /* KG: Less than or equal to 4 bytes can not be transfered via DMA, it seems. */ 2260 if (d_left_counter 2261 && srb->total_xfer_length <= DC395x_LASTPIO) { 2262 size_t left_io = srb->total_xfer_length; 2263 2264 /*u32 addr = (srb->segment_x[srb->sg_index].address); */ 2265 /*sg_update_list (srb, d_left_counter); */ 2266 dprintkdbg(DBG_PIO, "data_in_phase0: PIO (%i %s) " 2267 "for remaining %i bytes:", 2268 fc & 0x1f, 2269 (srb->dcb->sync_period & WIDE_SYNC) ? 2270 "words" : "bytes", 2271 srb->total_xfer_length); 2272 if (srb->dcb->sync_period & WIDE_SYNC) 2273 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG2, 2274 CFG2_WIDEFIFO); 2275 while (left_io) { 2276 unsigned char *virt, *base = NULL; 2277 unsigned long flags = 0; 2278 size_t len = left_io; 2279 size_t offset = srb->request_length - left_io; 2280 2281 local_irq_save(flags); 2282 /* Assumption: it's inside one page as it's at most 4 bytes and 2283 I just assume it's on a 4-byte boundary */ 2284 base = scsi_kmap_atomic_sg(scsi_sglist(srb->cmd), 2285 srb->sg_count, &offset, &len); 2286 virt = base + offset; 2287 2288 left_io -= len; 2289 2290 while (len) { 2291 u8 byte; 2292 byte = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2293 *virt++ = byte; 2294 2295 if (debug_enabled(DBG_PIO)) 2296 printk(" %02x", byte); 2297 2298 d_left_counter--; 2299 sg_subtract_one(srb); 2300 2301 len--; 2302 2303 fc = DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT); 2304 2305 if (fc == 0x40) { 2306 left_io = 0; 2307 break; 2308 } 2309 } 2310 2311 WARN_ON((fc != 0x40) == !d_left_counter); 2312 2313 if (fc == 0x40 && (srb->dcb->sync_period & WIDE_SYNC)) { 2314 /* Read the last byte ... */ 2315 if (srb->total_xfer_length > 0) { 2316 u8 byte = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2317 2318 *virt++ = byte; 2319 srb->total_xfer_length--; 2320 if (debug_enabled(DBG_PIO)) 2321 printk(" %02x", byte); 2322 } 2323 2324 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG2, 0); 2325 } 2326 2327 scsi_kunmap_atomic_sg(base); 2328 local_irq_restore(flags); 2329 } 2330 /*printk(" %08x", *(u32*)(bus_to_virt (addr))); */ 2331 /*srb->total_xfer_length = 0; */ 2332 if (debug_enabled(DBG_PIO)) 2333 printk("\n"); 2334 } 2335 #endif /* DC395x_LASTPIO */ 2336 2337 #if 0 2338 /* 2339 * KG: This was in DATAOUT. Does it also belong here? 2340 * Nobody seems to know what counter and fifo_cnt count exactly ... 2341 */ 2342 if (!(scsi_status & SCSIXFERDONE)) { 2343 /* 2344 * when data transfer from DMA FIFO to SCSI FIFO 2345 * if there was some data left in SCSI FIFO 2346 */ 2347 d_left_counter = 2348 (u32)(DC395x_read8(acb, TRM_S1040_SCSI_FIFOCNT) & 2349 0x1F); 2350 if (srb->dcb->sync_period & WIDE_SYNC) 2351 d_left_counter <<= 1; 2352 /* 2353 * if WIDE scsi SCSI FIFOCNT unit is word !!! 2354 * so need to *= 2 2355 * KG: Seems to be correct ... 2356 */ 2357 } 2358 #endif 2359 /* KG: This should not be needed any more! */ 2360 if (d_left_counter == 0 2361 || (scsi_status & SCSIXFERCNT_2_ZERO)) { 2362 #if 0 2363 int ctr = 6000000; 2364 u8 TempDMAstatus; 2365 do { 2366 TempDMAstatus = 2367 DC395x_read8(acb, TRM_S1040_DMA_STATUS); 2368 } while (!(TempDMAstatus & DMAXFERCOMP) && --ctr); 2369 if (!ctr) 2370 dprintkl(KERN_ERR, 2371 "Deadlock in DataInPhase0 waiting for DMA!!\n"); 2372 srb->total_xfer_length = 0; 2373 #endif 2374 srb->total_xfer_length = d_left_counter; 2375 } else { /* phase changed */ 2376 /* 2377 * parsing the case: 2378 * when a transfer not yet complete 2379 * but be disconnected by target 2380 * if transfer not yet complete 2381 * there were some data residue in SCSI FIFO or 2382 * SCSI transfer counter not empty 2383 */ 2384 sg_update_list(srb, d_left_counter); 2385 } 2386 } 2387 /* KG: The target may decide to disconnect: Empty FIFO before! */ 2388 if ((*pscsi_status & PHASEMASK) != PH_DATA_IN) { 2389 cleanup_after_transfer(acb, srb); 2390 } 2391 } 2392 2393 2394 static void data_in_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2395 u16 *pscsi_status) 2396 { 2397 dprintkdbg(DBG_0, "data_in_phase1: (pid#%li) <%02i-%i>\n", 2398 srb->cmd->serial_number, srb->cmd->device->id, srb->cmd->device->lun); 2399 data_io_transfer(acb, srb, XFERDATAIN); 2400 } 2401 2402 2403 static void data_io_transfer(struct AdapterCtlBlk *acb, 2404 struct ScsiReqBlk *srb, u16 io_dir) 2405 { 2406 struct DeviceCtlBlk *dcb = srb->dcb; 2407 u8 bval; 2408 dprintkdbg(DBG_0, 2409 "data_io_transfer: (pid#%li) <%02i-%i> %c len=%i, sg=(%i/%i)\n", 2410 srb->cmd->serial_number, srb->cmd->device->id, srb->cmd->device->lun, 2411 ((io_dir & DMACMD_DIR) ? 'r' : 'w'), 2412 srb->total_xfer_length, srb->sg_index, srb->sg_count); 2413 if (srb == acb->tmp_srb) 2414 dprintkl(KERN_ERR, "data_io_transfer: Using tmp_srb!\n"); 2415 if (srb->sg_index >= srb->sg_count) { 2416 /* can't happen? out of bounds error */ 2417 return; 2418 } 2419 2420 if (srb->total_xfer_length > DC395x_LASTPIO) { 2421 u8 dma_status = DC395x_read8(acb, TRM_S1040_DMA_STATUS); 2422 /* 2423 * KG: What should we do: Use SCSI Cmd 0x90/0x92? 2424 * Maybe, even ABORTXFER would be appropriate 2425 */ 2426 if (dma_status & XFERPENDING) { 2427 dprintkl(KERN_DEBUG, "data_io_transfer: Xfer pending! " 2428 "Expect trouble!\n"); 2429 dump_register_info(acb, dcb, srb); 2430 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, CLRXFIFO); 2431 } 2432 /* clear_fifo(acb, "IO"); */ 2433 /* 2434 * load what physical address of Scatter/Gather list table 2435 * want to be transfer 2436 */ 2437 srb->state |= SRB_DATA_XFER; 2438 DC395x_write32(acb, TRM_S1040_DMA_XHIGHADDR, 0); 2439 if (scsi_sg_count(srb->cmd)) { /* with S/G */ 2440 io_dir |= DMACMD_SG; 2441 DC395x_write32(acb, TRM_S1040_DMA_XLOWADDR, 2442 srb->sg_bus_addr + 2443 sizeof(struct SGentry) * 2444 srb->sg_index); 2445 /* load how many bytes in the sg list table */ 2446 DC395x_write32(acb, TRM_S1040_DMA_XCNT, 2447 ((u32)(srb->sg_count - 2448 srb->sg_index) << 3)); 2449 } else { /* without S/G */ 2450 io_dir &= ~DMACMD_SG; 2451 DC395x_write32(acb, TRM_S1040_DMA_XLOWADDR, 2452 srb->segment_x[0].address); 2453 DC395x_write32(acb, TRM_S1040_DMA_XCNT, 2454 srb->segment_x[0].length); 2455 } 2456 /* load total transfer length (24bits) max value 16Mbyte */ 2457 DC395x_write32(acb, TRM_S1040_SCSI_COUNTER, 2458 srb->total_xfer_length); 2459 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 2460 if (io_dir & DMACMD_DIR) { /* read */ 2461 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, 2462 SCMD_DMA_IN); 2463 DC395x_write16(acb, TRM_S1040_DMA_COMMAND, io_dir); 2464 } else { 2465 DC395x_write16(acb, TRM_S1040_DMA_COMMAND, io_dir); 2466 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, 2467 SCMD_DMA_OUT); 2468 } 2469 2470 } 2471 #if DC395x_LASTPIO 2472 else if (srb->total_xfer_length > 0) { /* The last four bytes: Do PIO */ 2473 /* 2474 * load what physical address of Scatter/Gather list table 2475 * want to be transfer 2476 */ 2477 srb->state |= SRB_DATA_XFER; 2478 /* load total transfer length (24bits) max value 16Mbyte */ 2479 DC395x_write32(acb, TRM_S1040_SCSI_COUNTER, 2480 srb->total_xfer_length); 2481 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 2482 if (io_dir & DMACMD_DIR) { /* read */ 2483 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, 2484 SCMD_FIFO_IN); 2485 } else { /* write */ 2486 int ln = srb->total_xfer_length; 2487 size_t left_io = srb->total_xfer_length; 2488 2489 if (srb->dcb->sync_period & WIDE_SYNC) 2490 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG2, 2491 CFG2_WIDEFIFO); 2492 2493 while (left_io) { 2494 unsigned char *virt, *base = NULL; 2495 unsigned long flags = 0; 2496 size_t len = left_io; 2497 size_t offset = srb->request_length - left_io; 2498 2499 local_irq_save(flags); 2500 /* Again, max 4 bytes */ 2501 base = scsi_kmap_atomic_sg(scsi_sglist(srb->cmd), 2502 srb->sg_count, &offset, &len); 2503 virt = base + offset; 2504 2505 left_io -= len; 2506 2507 while (len--) { 2508 if (debug_enabled(DBG_PIO)) 2509 printk(" %02x", *virt); 2510 2511 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, *virt++); 2512 2513 sg_subtract_one(srb); 2514 } 2515 2516 scsi_kunmap_atomic_sg(base); 2517 local_irq_restore(flags); 2518 } 2519 if (srb->dcb->sync_period & WIDE_SYNC) { 2520 if (ln % 2) { 2521 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 0); 2522 if (debug_enabled(DBG_PIO)) 2523 printk(" |00"); 2524 } 2525 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG2, 0); 2526 } 2527 /*DC395x_write32(acb, TRM_S1040_SCSI_COUNTER, ln); */ 2528 if (debug_enabled(DBG_PIO)) 2529 printk("\n"); 2530 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, 2531 SCMD_FIFO_OUT); 2532 } 2533 } 2534 #endif /* DC395x_LASTPIO */ 2535 else { /* xfer pad */ 2536 u8 data = 0, data2 = 0; 2537 if (srb->sg_count) { 2538 srb->adapter_status = H_OVER_UNDER_RUN; 2539 srb->status |= OVER_RUN; 2540 } 2541 /* 2542 * KG: despite the fact that we are using 16 bits I/O ops 2543 * the SCSI FIFO is only 8 bits according to the docs 2544 * (we can set bit 1 in 0x8f to serialize FIFO access ...) 2545 */ 2546 if (dcb->sync_period & WIDE_SYNC) { 2547 DC395x_write32(acb, TRM_S1040_SCSI_COUNTER, 2); 2548 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG2, 2549 CFG2_WIDEFIFO); 2550 if (io_dir & DMACMD_DIR) { 2551 data = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2552 data2 = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2553 } else { 2554 /* Danger, Robinson: If you find KGs 2555 * scattered over the wide disk, the driver 2556 * or chip is to blame :-( */ 2557 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 'K'); 2558 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 'G'); 2559 } 2560 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG2, 0); 2561 } else { 2562 DC395x_write32(acb, TRM_S1040_SCSI_COUNTER, 1); 2563 /* Danger, Robinson: If you find a collection of Ks on your disk 2564 * something broke :-( */ 2565 if (io_dir & DMACMD_DIR) 2566 data = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2567 else 2568 DC395x_write8(acb, TRM_S1040_SCSI_FIFO, 'K'); 2569 } 2570 srb->state |= SRB_XFERPAD; 2571 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 2572 /* SCSI command */ 2573 bval = (io_dir & DMACMD_DIR) ? SCMD_FIFO_IN : SCMD_FIFO_OUT; 2574 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, bval); 2575 } 2576 } 2577 2578 2579 static void status_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2580 u16 *pscsi_status) 2581 { 2582 dprintkdbg(DBG_0, "status_phase0: (pid#%li) <%02i-%i>\n", 2583 srb->cmd->serial_number, srb->cmd->device->id, srb->cmd->device->lun); 2584 srb->target_status = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2585 srb->end_message = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); /* get message */ 2586 srb->state = SRB_COMPLETED; 2587 *pscsi_status = PH_BUS_FREE; /*.. initial phase */ 2588 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 2589 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_MSGACCEPT); 2590 } 2591 2592 2593 static void status_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2594 u16 *pscsi_status) 2595 { 2596 dprintkdbg(DBG_0, "status_phase1: (pid#%li) <%02i-%i>\n", 2597 srb->cmd->serial_number, srb->cmd->device->id, srb->cmd->device->lun); 2598 srb->state = SRB_STATUS; 2599 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 2600 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_COMP); 2601 } 2602 2603 2604 /* Check if the message is complete */ 2605 static inline u8 msgin_completed(u8 * msgbuf, u32 len) 2606 { 2607 if (*msgbuf == EXTENDED_MESSAGE) { 2608 if (len < 2) 2609 return 0; 2610 if (len < msgbuf[1] + 2) 2611 return 0; 2612 } else if (*msgbuf >= 0x20 && *msgbuf <= 0x2f) /* two byte messages */ 2613 if (len < 2) 2614 return 0; 2615 return 1; 2616 } 2617 2618 /* reject_msg */ 2619 static inline void msgin_reject(struct AdapterCtlBlk *acb, 2620 struct ScsiReqBlk *srb) 2621 { 2622 srb->msgout_buf[0] = MESSAGE_REJECT; 2623 srb->msg_count = 1; 2624 DC395x_ENABLE_MSGOUT; 2625 srb->state &= ~SRB_MSGIN; 2626 srb->state |= SRB_MSGOUT; 2627 dprintkl(KERN_INFO, "msgin_reject: 0x%02x <%02i-%i>\n", 2628 srb->msgin_buf[0], 2629 srb->dcb->target_id, srb->dcb->target_lun); 2630 } 2631 2632 2633 static struct ScsiReqBlk *msgin_qtag(struct AdapterCtlBlk *acb, 2634 struct DeviceCtlBlk *dcb, u8 tag) 2635 { 2636 struct ScsiReqBlk *srb = NULL; 2637 struct ScsiReqBlk *i; 2638 dprintkdbg(DBG_0, "msgin_qtag: (pid#%li) tag=%i srb=%p\n", 2639 srb->cmd->serial_number, tag, srb); 2640 2641 if (!(dcb->tag_mask & (1 << tag))) 2642 dprintkl(KERN_DEBUG, 2643 "msgin_qtag: tag_mask=0x%08x does not reserve tag %i!\n", 2644 dcb->tag_mask, tag); 2645 2646 if (list_empty(&dcb->srb_going_list)) 2647 goto mingx0; 2648 list_for_each_entry(i, &dcb->srb_going_list, list) { 2649 if (i->tag_number == tag) { 2650 srb = i; 2651 break; 2652 } 2653 } 2654 if (!srb) 2655 goto mingx0; 2656 2657 dprintkdbg(DBG_0, "msgin_qtag: (pid#%li) <%02i-%i>\n", 2658 srb->cmd->serial_number, srb->dcb->target_id, srb->dcb->target_lun); 2659 if (dcb->flag & ABORT_DEV_) { 2660 /*srb->state = SRB_ABORT_SENT; */ 2661 enable_msgout_abort(acb, srb); 2662 } 2663 2664 if (!(srb->state & SRB_DISCONNECT)) 2665 goto mingx0; 2666 2667 memcpy(srb->msgin_buf, dcb->active_srb->msgin_buf, acb->msg_len); 2668 srb->state |= dcb->active_srb->state; 2669 srb->state |= SRB_DATA_XFER; 2670 dcb->active_srb = srb; 2671 /* How can we make the DORS happy? */ 2672 return srb; 2673 2674 mingx0: 2675 srb = acb->tmp_srb; 2676 srb->state = SRB_UNEXPECT_RESEL; 2677 dcb->active_srb = srb; 2678 srb->msgout_buf[0] = MSG_ABORT_TAG; 2679 srb->msg_count = 1; 2680 DC395x_ENABLE_MSGOUT; 2681 dprintkl(KERN_DEBUG, "msgin_qtag: Unknown tag %i - abort\n", tag); 2682 return srb; 2683 } 2684 2685 2686 static inline void reprogram_regs(struct AdapterCtlBlk *acb, 2687 struct DeviceCtlBlk *dcb) 2688 { 2689 DC395x_write8(acb, TRM_S1040_SCSI_TARGETID, dcb->target_id); 2690 DC395x_write8(acb, TRM_S1040_SCSI_SYNC, dcb->sync_period); 2691 DC395x_write8(acb, TRM_S1040_SCSI_OFFSET, dcb->sync_offset); 2692 set_xfer_rate(acb, dcb); 2693 } 2694 2695 2696 /* set async transfer mode */ 2697 static void msgin_set_async(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb) 2698 { 2699 struct DeviceCtlBlk *dcb = srb->dcb; 2700 dprintkl(KERN_DEBUG, "msgin_set_async: No sync transfers <%02i-%i>\n", 2701 dcb->target_id, dcb->target_lun); 2702 2703 dcb->sync_mode &= ~(SYNC_NEGO_ENABLE); 2704 dcb->sync_mode |= SYNC_NEGO_DONE; 2705 /*dcb->sync_period &= 0; */ 2706 dcb->sync_offset = 0; 2707 dcb->min_nego_period = 200 >> 2; /* 200ns <=> 5 MHz */ 2708 srb->state &= ~SRB_DO_SYNC_NEGO; 2709 reprogram_regs(acb, dcb); 2710 if ((dcb->sync_mode & WIDE_NEGO_ENABLE) 2711 && !(dcb->sync_mode & WIDE_NEGO_DONE)) { 2712 build_wdtr(acb, dcb, srb); 2713 DC395x_ENABLE_MSGOUT; 2714 dprintkdbg(DBG_0, "msgin_set_async(rej): Try WDTR anyway\n"); 2715 } 2716 } 2717 2718 2719 /* set sync transfer mode */ 2720 static void msgin_set_sync(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb) 2721 { 2722 struct DeviceCtlBlk *dcb = srb->dcb; 2723 u8 bval; 2724 int fact; 2725 dprintkdbg(DBG_1, "msgin_set_sync: <%02i> Sync: %ins " 2726 "(%02i.%01i MHz) Offset %i\n", 2727 dcb->target_id, srb->msgin_buf[3] << 2, 2728 (250 / srb->msgin_buf[3]), 2729 ((250 % srb->msgin_buf[3]) * 10) / srb->msgin_buf[3], 2730 srb->msgin_buf[4]); 2731 2732 if (srb->msgin_buf[4] > 15) 2733 srb->msgin_buf[4] = 15; 2734 if (!(dcb->dev_mode & NTC_DO_SYNC_NEGO)) 2735 dcb->sync_offset = 0; 2736 else if (dcb->sync_offset == 0) 2737 dcb->sync_offset = srb->msgin_buf[4]; 2738 if (srb->msgin_buf[4] > dcb->sync_offset) 2739 srb->msgin_buf[4] = dcb->sync_offset; 2740 else 2741 dcb->sync_offset = srb->msgin_buf[4]; 2742 bval = 0; 2743 while (bval < 7 && (srb->msgin_buf[3] > clock_period[bval] 2744 || dcb->min_nego_period > 2745 clock_period[bval])) 2746 bval++; 2747 if (srb->msgin_buf[3] < clock_period[bval]) 2748 dprintkl(KERN_INFO, 2749 "msgin_set_sync: Increase sync nego period to %ins\n", 2750 clock_period[bval] << 2); 2751 srb->msgin_buf[3] = clock_period[bval]; 2752 dcb->sync_period &= 0xf0; 2753 dcb->sync_period |= ALT_SYNC | bval; 2754 dcb->min_nego_period = srb->msgin_buf[3]; 2755 2756 if (dcb->sync_period & WIDE_SYNC) 2757 fact = 500; 2758 else 2759 fact = 250; 2760 2761 dprintkl(KERN_INFO, 2762 "Target %02i: %s Sync: %ins Offset %i (%02i.%01i MB/s)\n", 2763 dcb->target_id, (fact == 500) ? "Wide16" : "", 2764 dcb->min_nego_period << 2, dcb->sync_offset, 2765 (fact / dcb->min_nego_period), 2766 ((fact % dcb->min_nego_period) * 10 + 2767 dcb->min_nego_period / 2) / dcb->min_nego_period); 2768 2769 if (!(srb->state & SRB_DO_SYNC_NEGO)) { 2770 /* Reply with corrected SDTR Message */ 2771 dprintkl(KERN_DEBUG, "msgin_set_sync: answer w/%ins %i\n", 2772 srb->msgin_buf[3] << 2, srb->msgin_buf[4]); 2773 2774 memcpy(srb->msgout_buf, srb->msgin_buf, 5); 2775 srb->msg_count = 5; 2776 DC395x_ENABLE_MSGOUT; 2777 dcb->sync_mode |= SYNC_NEGO_DONE; 2778 } else { 2779 if ((dcb->sync_mode & WIDE_NEGO_ENABLE) 2780 && !(dcb->sync_mode & WIDE_NEGO_DONE)) { 2781 build_wdtr(acb, dcb, srb); 2782 DC395x_ENABLE_MSGOUT; 2783 dprintkdbg(DBG_0, "msgin_set_sync: Also try WDTR\n"); 2784 } 2785 } 2786 srb->state &= ~SRB_DO_SYNC_NEGO; 2787 dcb->sync_mode |= SYNC_NEGO_DONE | SYNC_NEGO_ENABLE; 2788 2789 reprogram_regs(acb, dcb); 2790 } 2791 2792 2793 static inline void msgin_set_nowide(struct AdapterCtlBlk *acb, 2794 struct ScsiReqBlk *srb) 2795 { 2796 struct DeviceCtlBlk *dcb = srb->dcb; 2797 dprintkdbg(DBG_1, "msgin_set_nowide: <%02i>\n", dcb->target_id); 2798 2799 dcb->sync_period &= ~WIDE_SYNC; 2800 dcb->sync_mode &= ~(WIDE_NEGO_ENABLE); 2801 dcb->sync_mode |= WIDE_NEGO_DONE; 2802 srb->state &= ~SRB_DO_WIDE_NEGO; 2803 reprogram_regs(acb, dcb); 2804 if ((dcb->sync_mode & SYNC_NEGO_ENABLE) 2805 && !(dcb->sync_mode & SYNC_NEGO_DONE)) { 2806 build_sdtr(acb, dcb, srb); 2807 DC395x_ENABLE_MSGOUT; 2808 dprintkdbg(DBG_0, "msgin_set_nowide: Rejected. Try SDTR anyway\n"); 2809 } 2810 } 2811 2812 static void msgin_set_wide(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb) 2813 { 2814 struct DeviceCtlBlk *dcb = srb->dcb; 2815 u8 wide = (dcb->dev_mode & NTC_DO_WIDE_NEGO 2816 && acb->config & HCC_WIDE_CARD) ? 1 : 0; 2817 dprintkdbg(DBG_1, "msgin_set_wide: <%02i>\n", dcb->target_id); 2818 2819 if (srb->msgin_buf[3] > wide) 2820 srb->msgin_buf[3] = wide; 2821 /* Completed */ 2822 if (!(srb->state & SRB_DO_WIDE_NEGO)) { 2823 dprintkl(KERN_DEBUG, 2824 "msgin_set_wide: Wide nego initiated <%02i>\n", 2825 dcb->target_id); 2826 memcpy(srb->msgout_buf, srb->msgin_buf, 4); 2827 srb->msg_count = 4; 2828 srb->state |= SRB_DO_WIDE_NEGO; 2829 DC395x_ENABLE_MSGOUT; 2830 } 2831 2832 dcb->sync_mode |= (WIDE_NEGO_ENABLE | WIDE_NEGO_DONE); 2833 if (srb->msgin_buf[3] > 0) 2834 dcb->sync_period |= WIDE_SYNC; 2835 else 2836 dcb->sync_period &= ~WIDE_SYNC; 2837 srb->state &= ~SRB_DO_WIDE_NEGO; 2838 /*dcb->sync_mode &= ~(WIDE_NEGO_ENABLE+WIDE_NEGO_DONE); */ 2839 dprintkdbg(DBG_1, 2840 "msgin_set_wide: Wide (%i bit) negotiated <%02i>\n", 2841 (8 << srb->msgin_buf[3]), dcb->target_id); 2842 reprogram_regs(acb, dcb); 2843 if ((dcb->sync_mode & SYNC_NEGO_ENABLE) 2844 && !(dcb->sync_mode & SYNC_NEGO_DONE)) { 2845 build_sdtr(acb, dcb, srb); 2846 DC395x_ENABLE_MSGOUT; 2847 dprintkdbg(DBG_0, "msgin_set_wide: Also try SDTR.\n"); 2848 } 2849 } 2850 2851 2852 /* 2853 * extended message codes: 2854 * 2855 * code description 2856 * 2857 * 02h Reserved 2858 * 00h MODIFY DATA POINTER 2859 * 01h SYNCHRONOUS DATA TRANSFER REQUEST 2860 * 03h WIDE DATA TRANSFER REQUEST 2861 * 04h - 7Fh Reserved 2862 * 80h - FFh Vendor specific 2863 */ 2864 static void msgin_phase0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2865 u16 *pscsi_status) 2866 { 2867 struct DeviceCtlBlk *dcb = acb->active_dcb; 2868 dprintkdbg(DBG_0, "msgin_phase0: (pid#%li)\n", srb->cmd->serial_number); 2869 2870 srb->msgin_buf[acb->msg_len++] = DC395x_read8(acb, TRM_S1040_SCSI_FIFO); 2871 if (msgin_completed(srb->msgin_buf, acb->msg_len)) { 2872 /* Now eval the msg */ 2873 switch (srb->msgin_buf[0]) { 2874 case DISCONNECT: 2875 srb->state = SRB_DISCONNECT; 2876 break; 2877 2878 case SIMPLE_QUEUE_TAG: 2879 case HEAD_OF_QUEUE_TAG: 2880 case ORDERED_QUEUE_TAG: 2881 srb = 2882 msgin_qtag(acb, dcb, 2883 srb->msgin_buf[1]); 2884 break; 2885 2886 case MESSAGE_REJECT: 2887 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, 2888 DO_CLRATN | DO_DATALATCH); 2889 /* A sync nego message was rejected ! */ 2890 if (srb->state & SRB_DO_SYNC_NEGO) { 2891 msgin_set_async(acb, srb); 2892 break; 2893 } 2894 /* A wide nego message was rejected ! */ 2895 if (srb->state & SRB_DO_WIDE_NEGO) { 2896 msgin_set_nowide(acb, srb); 2897 break; 2898 } 2899 enable_msgout_abort(acb, srb); 2900 /*srb->state |= SRB_ABORT_SENT */ 2901 break; 2902 2903 case EXTENDED_MESSAGE: 2904 /* SDTR */ 2905 if (srb->msgin_buf[1] == 3 2906 && srb->msgin_buf[2] == EXTENDED_SDTR) { 2907 msgin_set_sync(acb, srb); 2908 break; 2909 } 2910 /* WDTR */ 2911 if (srb->msgin_buf[1] == 2 2912 && srb->msgin_buf[2] == EXTENDED_WDTR 2913 && srb->msgin_buf[3] <= 2) { /* sanity check ... */ 2914 msgin_set_wide(acb, srb); 2915 break; 2916 } 2917 msgin_reject(acb, srb); 2918 break; 2919 2920 case MSG_IGNOREWIDE: 2921 /* Discard wide residual */ 2922 dprintkdbg(DBG_0, "msgin_phase0: Ignore Wide Residual!\n"); 2923 break; 2924 2925 case COMMAND_COMPLETE: 2926 /* nothing has to be done */ 2927 break; 2928 2929 case SAVE_POINTERS: 2930 /* 2931 * SAVE POINTER may be ignored as we have the struct 2932 * ScsiReqBlk* associated with the scsi command. 2933 */ 2934 dprintkdbg(DBG_0, "msgin_phase0: (pid#%li) " 2935 "SAVE POINTER rem=%i Ignore\n", 2936 srb->cmd->serial_number, srb->total_xfer_length); 2937 break; 2938 2939 case RESTORE_POINTERS: 2940 dprintkdbg(DBG_0, "msgin_phase0: RESTORE POINTER. Ignore\n"); 2941 break; 2942 2943 case ABORT: 2944 dprintkdbg(DBG_0, "msgin_phase0: (pid#%li) " 2945 "<%02i-%i> ABORT msg\n", 2946 srb->cmd->serial_number, dcb->target_id, 2947 dcb->target_lun); 2948 dcb->flag |= ABORT_DEV_; 2949 enable_msgout_abort(acb, srb); 2950 break; 2951 2952 default: 2953 /* reject unknown messages */ 2954 if (srb->msgin_buf[0] & IDENTIFY_BASE) { 2955 dprintkdbg(DBG_0, "msgin_phase0: Identify msg\n"); 2956 srb->msg_count = 1; 2957 srb->msgout_buf[0] = dcb->identify_msg; 2958 DC395x_ENABLE_MSGOUT; 2959 srb->state |= SRB_MSGOUT; 2960 /*break; */ 2961 } 2962 msgin_reject(acb, srb); 2963 } 2964 2965 /* Clear counter and MsgIn state */ 2966 srb->state &= ~SRB_MSGIN; 2967 acb->msg_len = 0; 2968 } 2969 *pscsi_status = PH_BUS_FREE; 2970 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important ... you know! */ 2971 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_MSGACCEPT); 2972 } 2973 2974 2975 static void msgin_phase1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2976 u16 *pscsi_status) 2977 { 2978 dprintkdbg(DBG_0, "msgin_phase1: (pid#%li)\n", srb->cmd->serial_number); 2979 clear_fifo(acb, "msgin_phase1"); 2980 DC395x_write32(acb, TRM_S1040_SCSI_COUNTER, 1); 2981 if (!(srb->state & SRB_MSGIN)) { 2982 srb->state &= ~SRB_DISCONNECT; 2983 srb->state |= SRB_MSGIN; 2984 } 2985 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 2986 /* SCSI command */ 2987 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_FIFO_IN); 2988 } 2989 2990 2991 static void nop0(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2992 u16 *pscsi_status) 2993 { 2994 } 2995 2996 2997 static void nop1(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb, 2998 u16 *pscsi_status) 2999 { 3000 } 3001 3002 3003 static void set_xfer_rate(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb) 3004 { 3005 struct DeviceCtlBlk *i; 3006 3007 /* set all lun device's period, offset */ 3008 if (dcb->identify_msg & 0x07) 3009 return; 3010 3011 if (acb->scan_devices) { 3012 current_sync_offset = dcb->sync_offset; 3013 return; 3014 } 3015 3016 list_for_each_entry(i, &acb->dcb_list, list) 3017 if (i->target_id == dcb->target_id) { 3018 i->sync_period = dcb->sync_period; 3019 i->sync_offset = dcb->sync_offset; 3020 i->sync_mode = dcb->sync_mode; 3021 i->min_nego_period = dcb->min_nego_period; 3022 } 3023 } 3024 3025 3026 static void disconnect(struct AdapterCtlBlk *acb) 3027 { 3028 struct DeviceCtlBlk *dcb = acb->active_dcb; 3029 struct ScsiReqBlk *srb; 3030 3031 if (!dcb) { 3032 dprintkl(KERN_ERR, "disconnect: No such device\n"); 3033 udelay(500); 3034 /* Suspend queue for a while */ 3035 acb->scsi_host->last_reset = 3036 jiffies + HZ / 2 + 3037 HZ * acb->eeprom.delay_time; 3038 clear_fifo(acb, "disconnectEx"); 3039 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_HWRESELECT); 3040 return; 3041 } 3042 srb = dcb->active_srb; 3043 acb->active_dcb = NULL; 3044 dprintkdbg(DBG_0, "disconnect: (pid#%li)\n", srb->cmd->serial_number); 3045 3046 srb->scsi_phase = PH_BUS_FREE; /* initial phase */ 3047 clear_fifo(acb, "disconnect"); 3048 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_HWRESELECT); 3049 if (srb->state & SRB_UNEXPECT_RESEL) { 3050 dprintkl(KERN_ERR, 3051 "disconnect: Unexpected reselection <%02i-%i>\n", 3052 dcb->target_id, dcb->target_lun); 3053 srb->state = 0; 3054 waiting_process_next(acb); 3055 } else if (srb->state & SRB_ABORT_SENT) { 3056 dcb->flag &= ~ABORT_DEV_; 3057 acb->scsi_host->last_reset = jiffies + HZ / 2 + 1; 3058 dprintkl(KERN_ERR, "disconnect: SRB_ABORT_SENT\n"); 3059 doing_srb_done(acb, DID_ABORT, srb->cmd, 1); 3060 waiting_process_next(acb); 3061 } else { 3062 if ((srb->state & (SRB_START_ + SRB_MSGOUT)) 3063 || !(srb-> 3064 state & (SRB_DISCONNECT + SRB_COMPLETED))) { 3065 /* 3066 * Selection time out 3067 * SRB_START_ || SRB_MSGOUT || (!SRB_DISCONNECT && !SRB_COMPLETED) 3068 */ 3069 /* Unexp. Disc / Sel Timeout */ 3070 if (srb->state != SRB_START_ 3071 && srb->state != SRB_MSGOUT) { 3072 srb->state = SRB_READY; 3073 dprintkl(KERN_DEBUG, 3074 "disconnect: (pid#%li) Unexpected\n", 3075 srb->cmd->serial_number); 3076 srb->target_status = SCSI_STAT_SEL_TIMEOUT; 3077 goto disc1; 3078 } else { 3079 /* Normal selection timeout */ 3080 dprintkdbg(DBG_KG, "disconnect: (pid#%li) " 3081 "<%02i-%i> SelTO\n", srb->cmd->serial_number, 3082 dcb->target_id, dcb->target_lun); 3083 if (srb->retry_count++ > DC395x_MAX_RETRIES 3084 || acb->scan_devices) { 3085 srb->target_status = 3086 SCSI_STAT_SEL_TIMEOUT; 3087 goto disc1; 3088 } 3089 free_tag(dcb, srb); 3090 srb_going_to_waiting_move(dcb, srb); 3091 dprintkdbg(DBG_KG, 3092 "disconnect: (pid#%li) Retry\n", 3093 srb->cmd->serial_number); 3094 waiting_set_timer(acb, HZ / 20); 3095 } 3096 } else if (srb->state & SRB_DISCONNECT) { 3097 u8 bval = DC395x_read8(acb, TRM_S1040_SCSI_SIGNAL); 3098 /* 3099 * SRB_DISCONNECT (This is what we expect!) 3100 */ 3101 if (bval & 0x40) { 3102 dprintkdbg(DBG_0, "disconnect: SCSI bus stat " 3103 " 0x%02x: ACK set! Other controllers?\n", 3104 bval); 3105 /* It could come from another initiator, therefore don't do much ! */ 3106 } else 3107 waiting_process_next(acb); 3108 } else if (srb->state & SRB_COMPLETED) { 3109 disc1: 3110 /* 3111 ** SRB_COMPLETED 3112 */ 3113 free_tag(dcb, srb); 3114 dcb->active_srb = NULL; 3115 srb->state = SRB_FREE; 3116 srb_done(acb, dcb, srb); 3117 } 3118 } 3119 } 3120 3121 3122 static void reselect(struct AdapterCtlBlk *acb) 3123 { 3124 struct DeviceCtlBlk *dcb = acb->active_dcb; 3125 struct ScsiReqBlk *srb = NULL; 3126 u16 rsel_tar_lun_id; 3127 u8 id, lun; 3128 u8 arblostflag = 0; 3129 dprintkdbg(DBG_0, "reselect: acb=%p\n", acb); 3130 3131 clear_fifo(acb, "reselect"); 3132 /*DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_HWRESELECT | DO_DATALATCH); */ 3133 /* Read Reselected Target ID and LUN */ 3134 rsel_tar_lun_id = DC395x_read16(acb, TRM_S1040_SCSI_TARGETID); 3135 if (dcb) { /* Arbitration lost but Reselection win */ 3136 srb = dcb->active_srb; 3137 if (!srb) { 3138 dprintkl(KERN_DEBUG, "reselect: Arb lost Resel won, " 3139 "but active_srb == NULL\n"); 3140 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 3141 return; 3142 } 3143 /* Why the if ? */ 3144 if (!acb->scan_devices) { 3145 dprintkdbg(DBG_KG, "reselect: (pid#%li) <%02i-%i> " 3146 "Arb lost but Resel win rsel=%i stat=0x%04x\n", 3147 srb->cmd->serial_number, dcb->target_id, 3148 dcb->target_lun, rsel_tar_lun_id, 3149 DC395x_read16(acb, TRM_S1040_SCSI_STATUS)); 3150 arblostflag = 1; 3151 /*srb->state |= SRB_DISCONNECT; */ 3152 3153 srb->state = SRB_READY; 3154 free_tag(dcb, srb); 3155 srb_going_to_waiting_move(dcb, srb); 3156 waiting_set_timer(acb, HZ / 20); 3157 3158 /* return; */ 3159 } 3160 } 3161 /* Read Reselected Target Id and LUN */ 3162 if (!(rsel_tar_lun_id & (IDENTIFY_BASE << 8))) 3163 dprintkl(KERN_DEBUG, "reselect: Expects identify msg. " 3164 "Got %i!\n", rsel_tar_lun_id); 3165 id = rsel_tar_lun_id & 0xff; 3166 lun = (rsel_tar_lun_id >> 8) & 7; 3167 dcb = find_dcb(acb, id, lun); 3168 if (!dcb) { 3169 dprintkl(KERN_ERR, "reselect: From non existent device " 3170 "<%02i-%i>\n", id, lun); 3171 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 3172 return; 3173 } 3174 acb->active_dcb = dcb; 3175 3176 if (!(dcb->dev_mode & NTC_DO_DISCONNECT)) 3177 dprintkl(KERN_DEBUG, "reselect: in spite of forbidden " 3178 "disconnection? <%02i-%i>\n", 3179 dcb->target_id, dcb->target_lun); 3180 3181 if (dcb->sync_mode & EN_TAG_QUEUEING /*&& !arblostflag */) { 3182 srb = acb->tmp_srb; 3183 dcb->active_srb = srb; 3184 } else { 3185 /* There can be only one! */ 3186 srb = dcb->active_srb; 3187 if (!srb || !(srb->state & SRB_DISCONNECT)) { 3188 /* 3189 * abort command 3190 */ 3191 dprintkl(KERN_DEBUG, 3192 "reselect: w/o disconnected cmds <%02i-%i>\n", 3193 dcb->target_id, dcb->target_lun); 3194 srb = acb->tmp_srb; 3195 srb->state = SRB_UNEXPECT_RESEL; 3196 dcb->active_srb = srb; 3197 enable_msgout_abort(acb, srb); 3198 } else { 3199 if (dcb->flag & ABORT_DEV_) { 3200 /*srb->state = SRB_ABORT_SENT; */ 3201 enable_msgout_abort(acb, srb); 3202 } else 3203 srb->state = SRB_DATA_XFER; 3204 3205 } 3206 } 3207 srb->scsi_phase = PH_BUS_FREE; /* initial phase */ 3208 3209 /* Program HA ID, target ID, period and offset */ 3210 dprintkdbg(DBG_0, "reselect: select <%i>\n", dcb->target_id); 3211 DC395x_write8(acb, TRM_S1040_SCSI_HOSTID, acb->scsi_host->this_id); /* host ID */ 3212 DC395x_write8(acb, TRM_S1040_SCSI_TARGETID, dcb->target_id); /* target ID */ 3213 DC395x_write8(acb, TRM_S1040_SCSI_OFFSET, dcb->sync_offset); /* offset */ 3214 DC395x_write8(acb, TRM_S1040_SCSI_SYNC, dcb->sync_period); /* sync period, wide */ 3215 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_DATALATCH); /* it's important for atn stop */ 3216 /* SCSI command */ 3217 DC395x_write8(acb, TRM_S1040_SCSI_COMMAND, SCMD_MSGACCEPT); 3218 } 3219 3220 3221 static inline u8 tagq_blacklist(char *name) 3222 { 3223 #ifndef DC395x_NO_TAGQ 3224 #if 0 3225 u8 i; 3226 for (i = 0; i < BADDEVCNT; i++) 3227 if (memcmp(name, DC395x_baddevname1[i], 28) == 0) 3228 return 1; 3229 #endif 3230 return 0; 3231 #else 3232 return 1; 3233 #endif 3234 } 3235 3236 3237 static void disc_tagq_set(struct DeviceCtlBlk *dcb, struct ScsiInqData *ptr) 3238 { 3239 /* Check for SCSI format (ANSI and Response data format) */ 3240 if ((ptr->Vers & 0x07) >= 2 || (ptr->RDF & 0x0F) == 2) { 3241 if ((ptr->Flags & SCSI_INQ_CMDQUEUE) 3242 && (dcb->dev_mode & NTC_DO_TAG_QUEUEING) && 3243 /*(dcb->dev_mode & NTC_DO_DISCONNECT) */ 3244 /* ((dcb->dev_type == TYPE_DISK) 3245 || (dcb->dev_type == TYPE_MOD)) && */ 3246 !tagq_blacklist(((char *)ptr) + 8)) { 3247 if (dcb->max_command == 1) 3248 dcb->max_command = 3249 dcb->acb->tag_max_num; 3250 dcb->sync_mode |= EN_TAG_QUEUEING; 3251 /*dcb->tag_mask = 0; */ 3252 } else 3253 dcb->max_command = 1; 3254 } 3255 } 3256 3257 3258 static void add_dev(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 3259 struct ScsiInqData *ptr) 3260 { 3261 u8 bval1 = ptr->DevType & SCSI_DEVTYPE; 3262 dcb->dev_type = bval1; 3263 /* if (bval1 == TYPE_DISK || bval1 == TYPE_MOD) */ 3264 disc_tagq_set(dcb, ptr); 3265 } 3266 3267 3268 /* unmap mapped pci regions from SRB */ 3269 static void pci_unmap_srb(struct AdapterCtlBlk *acb, struct ScsiReqBlk *srb) 3270 { 3271 struct scsi_cmnd *cmd = srb->cmd; 3272 enum dma_data_direction dir = cmd->sc_data_direction; 3273 3274 if (scsi_sg_count(cmd) && dir != PCI_DMA_NONE) { 3275 /* unmap DC395x SG list */ 3276 dprintkdbg(DBG_SG, "pci_unmap_srb: list=%08x(%05x)\n", 3277 srb->sg_bus_addr, SEGMENTX_LEN); 3278 pci_unmap_single(acb->dev, srb->sg_bus_addr, 3279 SEGMENTX_LEN, 3280 PCI_DMA_TODEVICE); 3281 dprintkdbg(DBG_SG, "pci_unmap_srb: segs=%i buffer=%p\n", 3282 scsi_sg_count(cmd), scsi_bufflen(cmd)); 3283 /* unmap the sg segments */ 3284 scsi_dma_unmap(cmd); 3285 } 3286 } 3287 3288 3289 /* unmap mapped pci sense buffer from SRB */ 3290 static void pci_unmap_srb_sense(struct AdapterCtlBlk *acb, 3291 struct ScsiReqBlk *srb) 3292 { 3293 if (!(srb->flag & AUTO_REQSENSE)) 3294 return; 3295 /* Unmap sense buffer */ 3296 dprintkdbg(DBG_SG, "pci_unmap_srb_sense: buffer=%08x\n", 3297 srb->segment_x[0].address); 3298 pci_unmap_single(acb->dev, srb->segment_x[0].address, 3299 srb->segment_x[0].length, PCI_DMA_FROMDEVICE); 3300 /* Restore SG stuff */ 3301 srb->total_xfer_length = srb->xferred; 3302 srb->segment_x[0].address = 3303 srb->segment_x[DC395x_MAX_SG_LISTENTRY - 1].address; 3304 srb->segment_x[0].length = 3305 srb->segment_x[DC395x_MAX_SG_LISTENTRY - 1].length; 3306 } 3307 3308 3309 /* 3310 * Complete execution of a SCSI command 3311 * Signal completion to the generic SCSI driver 3312 */ 3313 static void srb_done(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 3314 struct ScsiReqBlk *srb) 3315 { 3316 u8 tempcnt, status; 3317 struct scsi_cmnd *cmd = srb->cmd; 3318 enum dma_data_direction dir = cmd->sc_data_direction; 3319 int ckc_only = 1; 3320 3321 dprintkdbg(DBG_1, "srb_done: (pid#%li) <%02i-%i>\n", srb->cmd->serial_number, 3322 srb->cmd->device->id, srb->cmd->device->lun); 3323 dprintkdbg(DBG_SG, "srb_done: srb=%p sg=%i(%i/%i) buf=%p\n", 3324 srb, scsi_sg_count(cmd), srb->sg_index, srb->sg_count, 3325 scsi_sgtalbe(cmd)); 3326 status = srb->target_status; 3327 if (srb->flag & AUTO_REQSENSE) { 3328 dprintkdbg(DBG_0, "srb_done: AUTO_REQSENSE1\n"); 3329 pci_unmap_srb_sense(acb, srb); 3330 /* 3331 ** target status.......................... 3332 */ 3333 srb->flag &= ~AUTO_REQSENSE; 3334 srb->adapter_status = 0; 3335 srb->target_status = CHECK_CONDITION << 1; 3336 if (debug_enabled(DBG_1)) { 3337 switch (cmd->sense_buffer[2] & 0x0f) { 3338 case NOT_READY: 3339 dprintkl(KERN_DEBUG, 3340 "ReqSense: NOT_READY cmnd=0x%02x <%02i-%i> stat=%i scan=%i ", 3341 cmd->cmnd[0], dcb->target_id, 3342 dcb->target_lun, status, acb->scan_devices); 3343 break; 3344 case UNIT_ATTENTION: 3345 dprintkl(KERN_DEBUG, 3346 "ReqSense: UNIT_ATTENTION cmnd=0x%02x <%02i-%i> stat=%i scan=%i ", 3347 cmd->cmnd[0], dcb->target_id, 3348 dcb->target_lun, status, acb->scan_devices); 3349 break; 3350 case ILLEGAL_REQUEST: 3351 dprintkl(KERN_DEBUG, 3352 "ReqSense: ILLEGAL_REQUEST cmnd=0x%02x <%02i-%i> stat=%i scan=%i ", 3353 cmd->cmnd[0], dcb->target_id, 3354 dcb->target_lun, status, acb->scan_devices); 3355 break; 3356 case MEDIUM_ERROR: 3357 dprintkl(KERN_DEBUG, 3358 "ReqSense: MEDIUM_ERROR cmnd=0x%02x <%02i-%i> stat=%i scan=%i ", 3359 cmd->cmnd[0], dcb->target_id, 3360 dcb->target_lun, status, acb->scan_devices); 3361 break; 3362 case HARDWARE_ERROR: 3363 dprintkl(KERN_DEBUG, 3364 "ReqSense: HARDWARE_ERROR cmnd=0x%02x <%02i-%i> stat=%i scan=%i ", 3365 cmd->cmnd[0], dcb->target_id, 3366 dcb->target_lun, status, acb->scan_devices); 3367 break; 3368 } 3369 if (cmd->sense_buffer[7] >= 6) 3370 printk("sense=0x%02x ASC=0x%02x ASCQ=0x%02x " 3371 "(0x%08x 0x%08x)\n", 3372 cmd->sense_buffer[2], cmd->sense_buffer[12], 3373 cmd->sense_buffer[13], 3374 *((unsigned int *)(cmd->sense_buffer + 3)), 3375 *((unsigned int *)(cmd->sense_buffer + 8))); 3376 else 3377 printk("sense=0x%02x No ASC/ASCQ (0x%08x)\n", 3378 cmd->sense_buffer[2], 3379 *((unsigned int *)(cmd->sense_buffer + 3))); 3380 } 3381 3382 if (status == (CHECK_CONDITION << 1)) { 3383 cmd->result = DID_BAD_TARGET << 16; 3384 goto ckc_e; 3385 } 3386 dprintkdbg(DBG_0, "srb_done: AUTO_REQSENSE2\n"); 3387 3388 if (srb->total_xfer_length 3389 && srb->total_xfer_length >= cmd->underflow) 3390 cmd->result = 3391 MK_RES_LNX(DRIVER_SENSE, DID_OK, 3392 srb->end_message, CHECK_CONDITION); 3393 /*SET_RES_DID(cmd->result,DID_OK) */ 3394 else 3395 cmd->result = 3396 MK_RES_LNX(DRIVER_SENSE, DID_OK, 3397 srb->end_message, CHECK_CONDITION); 3398 3399 goto ckc_e; 3400 } 3401 3402 /*************************************************************/ 3403 if (status) { 3404 /* 3405 * target status.......................... 3406 */ 3407 if (status_byte(status) == CHECK_CONDITION) { 3408 request_sense(acb, dcb, srb); 3409 return; 3410 } else if (status_byte(status) == QUEUE_FULL) { 3411 tempcnt = (u8)list_size(&dcb->srb_going_list); 3412 dprintkl(KERN_INFO, "QUEUE_FULL for dev <%02i-%i> with %i cmnds\n", 3413 dcb->target_id, dcb->target_lun, tempcnt); 3414 if (tempcnt > 1) 3415 tempcnt--; 3416 dcb->max_command = tempcnt; 3417 free_tag(dcb, srb); 3418 srb_going_to_waiting_move(dcb, srb); 3419 waiting_set_timer(acb, HZ / 20); 3420 srb->adapter_status = 0; 3421 srb->target_status = 0; 3422 return; 3423 } else if (status == SCSI_STAT_SEL_TIMEOUT) { 3424 srb->adapter_status = H_SEL_TIMEOUT; 3425 srb->target_status = 0; 3426 cmd->result = DID_NO_CONNECT << 16; 3427 } else { 3428 srb->adapter_status = 0; 3429 SET_RES_DID(cmd->result, DID_ERROR); 3430 SET_RES_MSG(cmd->result, srb->end_message); 3431 SET_RES_TARGET(cmd->result, status); 3432 3433 } 3434 } else { 3435 /* 3436 ** process initiator status.......................... 3437 */ 3438 status = srb->adapter_status; 3439 if (status & H_OVER_UNDER_RUN) { 3440 srb->target_status = 0; 3441 SET_RES_DID(cmd->result, DID_OK); 3442 SET_RES_MSG(cmd->result, srb->end_message); 3443 } else if (srb->status & PARITY_ERROR) { 3444 SET_RES_DID(cmd->result, DID_PARITY); 3445 SET_RES_MSG(cmd->result, srb->end_message); 3446 } else { /* No error */ 3447 3448 srb->adapter_status = 0; 3449 srb->target_status = 0; 3450 SET_RES_DID(cmd->result, DID_OK); 3451 } 3452 } 3453 3454 if (dir != PCI_DMA_NONE && scsi_sg_count(cmd)) 3455 pci_dma_sync_sg_for_cpu(acb->dev, scsi_sglist(cmd), 3456 scsi_sg_count(cmd), dir); 3457 3458 ckc_only = 0; 3459 /* Check Error Conditions */ 3460 ckc_e: 3461 3462 if (cmd->cmnd[0] == INQUIRY) { 3463 unsigned char *base = NULL; 3464 struct ScsiInqData *ptr; 3465 unsigned long flags = 0; 3466 struct scatterlist* sg = scsi_sglist(cmd); 3467 size_t offset = 0, len = sizeof(struct ScsiInqData); 3468 3469 local_irq_save(flags); 3470 base = scsi_kmap_atomic_sg(sg, scsi_sg_count(cmd), &offset, &len); 3471 ptr = (struct ScsiInqData *)(base + offset); 3472 3473 if (!ckc_only && (cmd->result & RES_DID) == 0 3474 && cmd->cmnd[2] == 0 && scsi_bufflen(cmd) >= 8 3475 && dir != PCI_DMA_NONE && ptr && (ptr->Vers & 0x07) >= 2) 3476 dcb->inquiry7 = ptr->Flags; 3477 3478 /*if( srb->cmd->cmnd[0] == INQUIRY && */ 3479 /* (host_byte(cmd->result) == DID_OK || status_byte(cmd->result) & CHECK_CONDITION) ) */ 3480 if ((cmd->result == (DID_OK << 16) 3481 || status_byte(cmd->result) & 3482 CHECK_CONDITION)) { 3483 if (!dcb->init_tcq_flag) { 3484 add_dev(acb, dcb, ptr); 3485 dcb->init_tcq_flag = 1; 3486 } 3487 } 3488 3489 scsi_kunmap_atomic_sg(base); 3490 local_irq_restore(flags); 3491 } 3492 3493 /* Here is the info for Doug Gilbert's sg3 ... */ 3494 scsi_set_resid(cmd, srb->total_xfer_length); 3495 /* This may be interpreted by sb. or not ... */ 3496 cmd->SCp.this_residual = srb->total_xfer_length; 3497 cmd->SCp.buffers_residual = 0; 3498 if (debug_enabled(DBG_KG)) { 3499 if (srb->total_xfer_length) 3500 dprintkdbg(DBG_KG, "srb_done: (pid#%li) <%02i-%i> " 3501 "cmnd=0x%02x Missed %i bytes\n", 3502 cmd->serial_number, cmd->device->id, cmd->device->lun, 3503 cmd->cmnd[0], srb->total_xfer_length); 3504 } 3505 3506 srb_going_remove(dcb, srb); 3507 /* Add to free list */ 3508 if (srb == acb->tmp_srb) 3509 dprintkl(KERN_ERR, "srb_done: ERROR! Completed cmd with tmp_srb\n"); 3510 else { 3511 dprintkdbg(DBG_0, "srb_done: (pid#%li) done result=0x%08x\n", 3512 cmd->serial_number, cmd->result); 3513 srb_free_insert(acb, srb); 3514 } 3515 pci_unmap_srb(acb, srb); 3516 3517 cmd->scsi_done(cmd); 3518 waiting_process_next(acb); 3519 } 3520 3521 3522 /* abort all cmds in our queues */ 3523 static void doing_srb_done(struct AdapterCtlBlk *acb, u8 did_flag, 3524 struct scsi_cmnd *cmd, u8 force) 3525 { 3526 struct DeviceCtlBlk *dcb; 3527 dprintkl(KERN_INFO, "doing_srb_done: pids "); 3528 3529 list_for_each_entry(dcb, &acb->dcb_list, list) { 3530 struct ScsiReqBlk *srb; 3531 struct ScsiReqBlk *tmp; 3532 struct scsi_cmnd *p; 3533 3534 list_for_each_entry_safe(srb, tmp, &dcb->srb_going_list, list) { 3535 enum dma_data_direction dir; 3536 int result; 3537 3538 p = srb->cmd; 3539 dir = p->sc_data_direction; 3540 result = MK_RES(0, did_flag, 0, 0); 3541 printk("G:%li(%02i-%i) ", p->serial_number, 3542 p->device->id, p->device->lun); 3543 srb_going_remove(dcb, srb); 3544 free_tag(dcb, srb); 3545 srb_free_insert(acb, srb); 3546 p->result = result; 3547 pci_unmap_srb_sense(acb, srb); 3548 pci_unmap_srb(acb, srb); 3549 if (force) { 3550 /* For new EH, we normally don't need to give commands back, 3551 * as they all complete or all time out */ 3552 p->scsi_done(p); 3553 } 3554 } 3555 if (!list_empty(&dcb->srb_going_list)) 3556 dprintkl(KERN_DEBUG, 3557 "How could the ML send cmnds to the Going queue? <%02i-%i>\n", 3558 dcb->target_id, dcb->target_lun); 3559 if (dcb->tag_mask) 3560 dprintkl(KERN_DEBUG, 3561 "tag_mask for <%02i-%i> should be empty, is %08x!\n", 3562 dcb->target_id, dcb->target_lun, 3563 dcb->tag_mask); 3564 3565 /* Waiting queue */ 3566 list_for_each_entry_safe(srb, tmp, &dcb->srb_waiting_list, list) { 3567 int result; 3568 p = srb->cmd; 3569 3570 result = MK_RES(0, did_flag, 0, 0); 3571 printk("W:%li<%02i-%i>", p->serial_number, p->device->id, 3572 p->device->lun); 3573 srb_waiting_remove(dcb, srb); 3574 srb_free_insert(acb, srb); 3575 p->result = result; 3576 pci_unmap_srb_sense(acb, srb); 3577 pci_unmap_srb(acb, srb); 3578 if (force) { 3579 /* For new EH, we normally don't need to give commands back, 3580 * as they all complete or all time out */ 3581 cmd->scsi_done(cmd); 3582 } 3583 } 3584 if (!list_empty(&dcb->srb_waiting_list)) 3585 dprintkl(KERN_DEBUG, "ML queued %i cmnds again to <%02i-%i>\n", 3586 list_size(&dcb->srb_waiting_list), dcb->target_id, 3587 dcb->target_lun); 3588 dcb->flag &= ~ABORT_DEV_; 3589 } 3590 printk("\n"); 3591 } 3592 3593 3594 static void reset_scsi_bus(struct AdapterCtlBlk *acb) 3595 { 3596 dprintkdbg(DBG_0, "reset_scsi_bus: acb=%p\n", acb); 3597 acb->acb_flag |= RESET_DEV; /* RESET_DETECT, RESET_DONE, RESET_DEV */ 3598 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_RSTSCSI); 3599 3600 while (!(DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS) & INT_SCSIRESET)) 3601 /* nothing */; 3602 } 3603 3604 3605 static void set_basic_config(struct AdapterCtlBlk *acb) 3606 { 3607 u8 bval; 3608 u16 wval; 3609 DC395x_write8(acb, TRM_S1040_SCSI_TIMEOUT, acb->sel_timeout); 3610 if (acb->config & HCC_PARITY) 3611 bval = PHASELATCH | INITIATOR | BLOCKRST | PARITYCHECK; 3612 else 3613 bval = PHASELATCH | INITIATOR | BLOCKRST; 3614 3615 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG0, bval); 3616 3617 /* program configuration 1: Act_Neg (+ Act_Neg_Enh? + Fast_Filter? + DataDis?) */ 3618 DC395x_write8(acb, TRM_S1040_SCSI_CONFIG1, 0x03); /* was 0x13: default */ 3619 /* program Host ID */ 3620 DC395x_write8(acb, TRM_S1040_SCSI_HOSTID, acb->scsi_host->this_id); 3621 /* set ansynchronous transfer */ 3622 DC395x_write8(acb, TRM_S1040_SCSI_OFFSET, 0x00); 3623 /* Turn LED control off */ 3624 wval = DC395x_read16(acb, TRM_S1040_GEN_CONTROL) & 0x7F; 3625 DC395x_write16(acb, TRM_S1040_GEN_CONTROL, wval); 3626 /* DMA config */ 3627 wval = DC395x_read16(acb, TRM_S1040_DMA_CONFIG) & ~DMA_FIFO_CTRL; 3628 wval |= 3629 DMA_FIFO_HALF_HALF | DMA_ENHANCE /*| DMA_MEM_MULTI_READ */ ; 3630 DC395x_write16(acb, TRM_S1040_DMA_CONFIG, wval); 3631 /* Clear pending interrupt status */ 3632 DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS); 3633 /* Enable SCSI interrupt */ 3634 DC395x_write8(acb, TRM_S1040_SCSI_INTEN, 0x7F); 3635 DC395x_write8(acb, TRM_S1040_DMA_INTEN, EN_SCSIINTR | EN_DMAXFERERROR 3636 /*| EN_DMAXFERABORT | EN_DMAXFERCOMP | EN_FORCEDMACOMP */ 3637 ); 3638 } 3639 3640 3641 static void scsi_reset_detect(struct AdapterCtlBlk *acb) 3642 { 3643 dprintkl(KERN_INFO, "scsi_reset_detect: acb=%p\n", acb); 3644 /* delay half a second */ 3645 if (timer_pending(&acb->waiting_timer)) 3646 del_timer(&acb->waiting_timer); 3647 3648 DC395x_write8(acb, TRM_S1040_SCSI_CONTROL, DO_RSTMODULE); 3649 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, DMARESETMODULE); 3650 /*DC395x_write8(acb, TRM_S1040_DMA_CONTROL,STOPDMAXFER); */ 3651 udelay(500); 3652 /* Maybe we locked up the bus? Then lets wait even longer ... */ 3653 acb->scsi_host->last_reset = 3654 jiffies + 5 * HZ / 2 + 3655 HZ * acb->eeprom.delay_time; 3656 3657 clear_fifo(acb, "scsi_reset_detect"); 3658 set_basic_config(acb); 3659 /*1.25 */ 3660 /*DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_HWRESELECT); */ 3661 3662 if (acb->acb_flag & RESET_DEV) { /* RESET_DETECT, RESET_DONE, RESET_DEV */ 3663 acb->acb_flag |= RESET_DONE; 3664 } else { 3665 acb->acb_flag |= RESET_DETECT; 3666 reset_dev_param(acb); 3667 doing_srb_done(acb, DID_RESET, NULL, 1); 3668 /*DC395x_RecoverSRB( acb ); */ 3669 acb->active_dcb = NULL; 3670 acb->acb_flag = 0; 3671 waiting_process_next(acb); 3672 } 3673 } 3674 3675 3676 static void request_sense(struct AdapterCtlBlk *acb, struct DeviceCtlBlk *dcb, 3677 struct ScsiReqBlk *srb) 3678 { 3679 struct scsi_cmnd *cmd = srb->cmd; 3680 dprintkdbg(DBG_1, "request_sense: (pid#%li) <%02i-%i>\n", 3681 cmd->serial_number, cmd->device->id, cmd->device->lun); 3682 3683 srb->flag |= AUTO_REQSENSE; 3684 srb->adapter_status = 0; 3685 srb->target_status = 0; 3686 3687 /* KG: Can this prevent crap sense data ? */ 3688 memset(cmd->sense_buffer, 0, SCSI_SENSE_BUFFERSIZE); 3689 3690 /* Save some data */ 3691 srb->segment_x[DC395x_MAX_SG_LISTENTRY - 1].address = 3692 srb->segment_x[0].address; 3693 srb->segment_x[DC395x_MAX_SG_LISTENTRY - 1].length = 3694 srb->segment_x[0].length; 3695 srb->xferred = srb->total_xfer_length; 3696 /* srb->segment_x : a one entry of S/G list table */ 3697 srb->total_xfer_length = SCSI_SENSE_BUFFERSIZE; 3698 srb->segment_x[0].length = SCSI_SENSE_BUFFERSIZE; 3699 /* Map sense buffer */ 3700 srb->segment_x[0].address = 3701 pci_map_single(acb->dev, cmd->sense_buffer, 3702 SCSI_SENSE_BUFFERSIZE, PCI_DMA_FROMDEVICE); 3703 dprintkdbg(DBG_SG, "request_sense: map buffer %p->%08x(%05x)\n", 3704 cmd->sense_buffer, srb->segment_x[0].address, 3705 SCSI_SENSE_BUFFERSIZE); 3706 srb->sg_count = 1; 3707 srb->sg_index = 0; 3708 3709 if (start_scsi(acb, dcb, srb)) { /* Should only happen, if sb. else grabs the bus */ 3710 dprintkl(KERN_DEBUG, 3711 "request_sense: (pid#%li) failed <%02i-%i>\n", 3712 srb->cmd->serial_number, dcb->target_id, dcb->target_lun); 3713 srb_going_to_waiting_move(dcb, srb); 3714 waiting_set_timer(acb, HZ / 100); 3715 } 3716 } 3717 3718 3719 /** 3720 * device_alloc - Allocate a new device instance. This create the 3721 * devices instance and sets up all the data items. The adapter 3722 * instance is required to obtain confiuration information for this 3723 * device. This does *not* add this device to the adapters device 3724 * list. 3725 * 3726 * @acb: The adapter to obtain configuration information from. 3727 * @target: The target for the new device. 3728 * @lun: The lun for the new device. 3729 * 3730 * Return the new device if successful or NULL on failure. 3731 **/ 3732 static struct DeviceCtlBlk *device_alloc(struct AdapterCtlBlk *acb, 3733 u8 target, u8 lun) 3734 { 3735 struct NvRamType *eeprom = &acb->eeprom; 3736 u8 period_index = eeprom->target[target].period & 0x07; 3737 struct DeviceCtlBlk *dcb; 3738 3739 dcb = kmalloc(sizeof(struct DeviceCtlBlk), GFP_ATOMIC); 3740 dprintkdbg(DBG_0, "device_alloc: <%02i-%i>\n", target, lun); 3741 if (!dcb) 3742 return NULL; 3743 dcb->acb = NULL; 3744 INIT_LIST_HEAD(&dcb->srb_going_list); 3745 INIT_LIST_HEAD(&dcb->srb_waiting_list); 3746 dcb->active_srb = NULL; 3747 dcb->tag_mask = 0; 3748 dcb->max_command = 1; 3749 dcb->target_id = target; 3750 dcb->target_lun = lun; 3751 #ifndef DC395x_NO_DISCONNECT 3752 dcb->identify_msg = 3753 IDENTIFY(dcb->dev_mode & NTC_DO_DISCONNECT, lun); 3754 #else 3755 dcb->identify_msg = IDENTIFY(0, lun); 3756 #endif 3757 dcb->dev_mode = eeprom->target[target].cfg0; 3758 dcb->inquiry7 = 0; 3759 dcb->sync_mode = 0; 3760 dcb->min_nego_period = clock_period[period_index]; 3761 dcb->sync_period = 0; 3762 dcb->sync_offset = 0; 3763 dcb->flag = 0; 3764 3765 #ifndef DC395x_NO_WIDE 3766 if ((dcb->dev_mode & NTC_DO_WIDE_NEGO) 3767 && (acb->config & HCC_WIDE_CARD)) 3768 dcb->sync_mode |= WIDE_NEGO_ENABLE; 3769 #endif 3770 #ifndef DC395x_NO_SYNC 3771 if (dcb->dev_mode & NTC_DO_SYNC_NEGO) 3772 if (!(lun) || current_sync_offset) 3773 dcb->sync_mode |= SYNC_NEGO_ENABLE; 3774 #endif 3775 if (dcb->target_lun != 0) { 3776 /* Copy settings */ 3777 struct DeviceCtlBlk *p; 3778 list_for_each_entry(p, &acb->dcb_list, list) 3779 if (p->target_id == dcb->target_id) 3780 break; 3781 dprintkdbg(DBG_1, 3782 "device_alloc: <%02i-%i> copy from <%02i-%i>\n", 3783 dcb->target_id, dcb->target_lun, 3784 p->target_id, p->target_lun); 3785 dcb->sync_mode = p->sync_mode; 3786 dcb->sync_period = p->sync_period; 3787 dcb->min_nego_period = p->min_nego_period; 3788 dcb->sync_offset = p->sync_offset; 3789 dcb->inquiry7 = p->inquiry7; 3790 } 3791 return dcb; 3792 } 3793 3794 3795 /** 3796 * adapter_add_device - Adds the device instance to the adaptor instance. 3797 * 3798 * @acb: The adapter device to be updated 3799 * @dcb: A newly created and initialised device instance to add. 3800 **/ 3801 static void adapter_add_device(struct AdapterCtlBlk *acb, 3802 struct DeviceCtlBlk *dcb) 3803 { 3804 /* backpointer to adapter */ 3805 dcb->acb = acb; 3806 3807 /* set run_robin to this device if it is currently empty */ 3808 if (list_empty(&acb->dcb_list)) 3809 acb->dcb_run_robin = dcb; 3810 3811 /* add device to list */ 3812 list_add_tail(&dcb->list, &acb->dcb_list); 3813 3814 /* update device maps */ 3815 acb->dcb_map[dcb->target_id] |= (1 << dcb->target_lun); 3816 acb->children[dcb->target_id][dcb->target_lun] = dcb; 3817 } 3818 3819 3820 /** 3821 * adapter_remove_device - Removes the device instance from the adaptor 3822 * instance. The device instance is not check in any way or freed by this. 3823 * The caller is expected to take care of that. This will simply remove the 3824 * device from the adapters data strcutures. 3825 * 3826 * @acb: The adapter device to be updated 3827 * @dcb: A device that has previously been added to the adapter. 3828 **/ 3829 static void adapter_remove_device(struct AdapterCtlBlk *acb, 3830 struct DeviceCtlBlk *dcb) 3831 { 3832 struct DeviceCtlBlk *i; 3833 struct DeviceCtlBlk *tmp; 3834 dprintkdbg(DBG_0, "adapter_remove_device: <%02i-%i>\n", 3835 dcb->target_id, dcb->target_lun); 3836 3837 /* fix up any pointers to this device that we have in the adapter */ 3838 if (acb->active_dcb == dcb) 3839 acb->active_dcb = NULL; 3840 if (acb->dcb_run_robin == dcb) 3841 acb->dcb_run_robin = dcb_get_next(&acb->dcb_list, dcb); 3842 3843 /* unlink from list */ 3844 list_for_each_entry_safe(i, tmp, &acb->dcb_list, list) 3845 if (dcb == i) { 3846 list_del(&i->list); 3847 break; 3848 } 3849 3850 /* clear map and children */ 3851 acb->dcb_map[dcb->target_id] &= ~(1 << dcb->target_lun); 3852 acb->children[dcb->target_id][dcb->target_lun] = NULL; 3853 dcb->acb = NULL; 3854 } 3855 3856 3857 /** 3858 * adapter_remove_and_free_device - Removes a single device from the adapter 3859 * and then frees the device information. 3860 * 3861 * @acb: The adapter device to be updated 3862 * @dcb: A device that has previously been added to the adapter. 3863 */ 3864 static void adapter_remove_and_free_device(struct AdapterCtlBlk *acb, 3865 struct DeviceCtlBlk *dcb) 3866 { 3867 if (list_size(&dcb->srb_going_list) > 1) { 3868 dprintkdbg(DBG_1, "adapter_remove_and_free_device: <%02i-%i> " 3869 "Won't remove because of %i active requests.\n", 3870 dcb->target_id, dcb->target_lun, 3871 list_size(&dcb->srb_going_list)); 3872 return; 3873 } 3874 adapter_remove_device(acb, dcb); 3875 kfree(dcb); 3876 } 3877 3878 3879 /** 3880 * adapter_remove_and_free_all_devices - Removes and frees all of the 3881 * devices associated with the specified adapter. 3882 * 3883 * @acb: The adapter from which all devices should be removed. 3884 **/ 3885 static void adapter_remove_and_free_all_devices(struct AdapterCtlBlk* acb) 3886 { 3887 struct DeviceCtlBlk *dcb; 3888 struct DeviceCtlBlk *tmp; 3889 dprintkdbg(DBG_1, "adapter_remove_and_free_all_devices: num=%i\n", 3890 list_size(&acb->dcb_list)); 3891 3892 list_for_each_entry_safe(dcb, tmp, &acb->dcb_list, list) 3893 adapter_remove_and_free_device(acb, dcb); 3894 } 3895 3896 3897 /** 3898 * dc395x_slave_alloc - Called by the scsi mid layer to tell us about a new 3899 * scsi device that we need to deal with. We allocate a new device and then 3900 * insert that device into the adapters device list. 3901 * 3902 * @scsi_device: The new scsi device that we need to handle. 3903 **/ 3904 static int dc395x_slave_alloc(struct scsi_device *scsi_device) 3905 { 3906 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)scsi_device->host->hostdata; 3907 struct DeviceCtlBlk *dcb; 3908 3909 dcb = device_alloc(acb, scsi_device->id, scsi_device->lun); 3910 if (!dcb) 3911 return -ENOMEM; 3912 adapter_add_device(acb, dcb); 3913 3914 return 0; 3915 } 3916 3917 3918 /** 3919 * dc395x_slave_destroy - Called by the scsi mid layer to tell us about a 3920 * device that is going away. 3921 * 3922 * @scsi_device: The new scsi device that we need to handle. 3923 **/ 3924 static void dc395x_slave_destroy(struct scsi_device *scsi_device) 3925 { 3926 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)scsi_device->host->hostdata; 3927 struct DeviceCtlBlk *dcb = find_dcb(acb, scsi_device->id, scsi_device->lun); 3928 if (dcb) 3929 adapter_remove_and_free_device(acb, dcb); 3930 } 3931 3932 3933 3934 3935 /** 3936 * trms1040_wait_30us: wait for 30 us 3937 * 3938 * Waits for 30us (using the chip by the looks of it..) 3939 * 3940 * @io_port: base I/O address 3941 **/ 3942 static void __devinit trms1040_wait_30us(unsigned long io_port) 3943 { 3944 /* ScsiPortStallExecution(30); wait 30 us */ 3945 outb(5, io_port + TRM_S1040_GEN_TIMER); 3946 while (!(inb(io_port + TRM_S1040_GEN_STATUS) & GTIMEOUT)) 3947 /* nothing */ ; 3948 } 3949 3950 3951 /** 3952 * trms1040_write_cmd - write the secified command and address to 3953 * chip 3954 * 3955 * @io_port: base I/O address 3956 * @cmd: SB + op code (command) to send 3957 * @addr: address to send 3958 **/ 3959 static void __devinit trms1040_write_cmd(unsigned long io_port, u8 cmd, u8 addr) 3960 { 3961 int i; 3962 u8 send_data; 3963 3964 /* program SB + OP code */ 3965 for (i = 0; i < 3; i++, cmd <<= 1) { 3966 send_data = NVR_SELECT; 3967 if (cmd & 0x04) /* Start from bit 2 */ 3968 send_data |= NVR_BITOUT; 3969 3970 outb(send_data, io_port + TRM_S1040_GEN_NVRAM); 3971 trms1040_wait_30us(io_port); 3972 outb((send_data | NVR_CLOCK), 3973 io_port + TRM_S1040_GEN_NVRAM); 3974 trms1040_wait_30us(io_port); 3975 } 3976 3977 /* send address */ 3978 for (i = 0; i < 7; i++, addr <<= 1) { 3979 send_data = NVR_SELECT; 3980 if (addr & 0x40) /* Start from bit 6 */ 3981 send_data |= NVR_BITOUT; 3982 3983 outb(send_data, io_port + TRM_S1040_GEN_NVRAM); 3984 trms1040_wait_30us(io_port); 3985 outb((send_data | NVR_CLOCK), 3986 io_port + TRM_S1040_GEN_NVRAM); 3987 trms1040_wait_30us(io_port); 3988 } 3989 outb(NVR_SELECT, io_port + TRM_S1040_GEN_NVRAM); 3990 trms1040_wait_30us(io_port); 3991 } 3992 3993 3994 /** 3995 * trms1040_set_data - store a single byte in the eeprom 3996 * 3997 * Called from write all to write a single byte into the SSEEPROM 3998 * Which is done one bit at a time. 3999 * 4000 * @io_port: base I/O address 4001 * @addr: offset into EEPROM 4002 * @byte: bytes to write 4003 **/ 4004 static void __devinit trms1040_set_data(unsigned long io_port, u8 addr, u8 byte) 4005 { 4006 int i; 4007 u8 send_data; 4008 4009 /* Send write command & address */ 4010 trms1040_write_cmd(io_port, 0x05, addr); 4011 4012 /* Write data */ 4013 for (i = 0; i < 8; i++, byte <<= 1) { 4014 send_data = NVR_SELECT; 4015 if (byte & 0x80) /* Start from bit 7 */ 4016 send_data |= NVR_BITOUT; 4017 4018 outb(send_data, io_port + TRM_S1040_GEN_NVRAM); 4019 trms1040_wait_30us(io_port); 4020 outb((send_data | NVR_CLOCK), io_port + TRM_S1040_GEN_NVRAM); 4021 trms1040_wait_30us(io_port); 4022 } 4023 outb(NVR_SELECT, io_port + TRM_S1040_GEN_NVRAM); 4024 trms1040_wait_30us(io_port); 4025 4026 /* Disable chip select */ 4027 outb(0, io_port + TRM_S1040_GEN_NVRAM); 4028 trms1040_wait_30us(io_port); 4029 4030 outb(NVR_SELECT, io_port + TRM_S1040_GEN_NVRAM); 4031 trms1040_wait_30us(io_port); 4032 4033 /* Wait for write ready */ 4034 while (1) { 4035 outb((NVR_SELECT | NVR_CLOCK), io_port + TRM_S1040_GEN_NVRAM); 4036 trms1040_wait_30us(io_port); 4037 4038 outb(NVR_SELECT, io_port + TRM_S1040_GEN_NVRAM); 4039 trms1040_wait_30us(io_port); 4040 4041 if (inb(io_port + TRM_S1040_GEN_NVRAM) & NVR_BITIN) 4042 break; 4043 } 4044 4045 /* Disable chip select */ 4046 outb(0, io_port + TRM_S1040_GEN_NVRAM); 4047 } 4048 4049 4050 /** 4051 * trms1040_write_all - write 128 bytes to the eeprom 4052 * 4053 * Write the supplied 128 bytes to the chips SEEPROM 4054 * 4055 * @eeprom: the data to write 4056 * @io_port: the base io port 4057 **/ 4058 static void __devinit trms1040_write_all(struct NvRamType *eeprom, unsigned long io_port) 4059 { 4060 u8 *b_eeprom = (u8 *)eeprom; 4061 u8 addr; 4062 4063 /* Enable SEEPROM */ 4064 outb((inb(io_port + TRM_S1040_GEN_CONTROL) | EN_EEPROM), 4065 io_port + TRM_S1040_GEN_CONTROL); 4066 4067 /* write enable */ 4068 trms1040_write_cmd(io_port, 0x04, 0xFF); 4069 outb(0, io_port + TRM_S1040_GEN_NVRAM); 4070 trms1040_wait_30us(io_port); 4071 4072 /* write */ 4073 for (addr = 0; addr < 128; addr++, b_eeprom++) 4074 trms1040_set_data(io_port, addr, *b_eeprom); 4075 4076 /* write disable */ 4077 trms1040_write_cmd(io_port, 0x04, 0x00); 4078 outb(0, io_port + TRM_S1040_GEN_NVRAM); 4079 trms1040_wait_30us(io_port); 4080 4081 /* Disable SEEPROM */ 4082 outb((inb(io_port + TRM_S1040_GEN_CONTROL) & ~EN_EEPROM), 4083 io_port + TRM_S1040_GEN_CONTROL); 4084 } 4085 4086 4087 /** 4088 * trms1040_get_data - get a single byte from the eeprom 4089 * 4090 * Called from read all to read a single byte into the SSEEPROM 4091 * Which is done one bit at a time. 4092 * 4093 * @io_port: base I/O address 4094 * @addr: offset into SEEPROM 4095 * 4096 * Returns the byte read. 4097 **/ 4098 static u8 __devinit trms1040_get_data(unsigned long io_port, u8 addr) 4099 { 4100 int i; 4101 u8 read_byte; 4102 u8 result = 0; 4103 4104 /* Send read command & address */ 4105 trms1040_write_cmd(io_port, 0x06, addr); 4106 4107 /* read data */ 4108 for (i = 0; i < 8; i++) { 4109 outb((NVR_SELECT | NVR_CLOCK), io_port + TRM_S1040_GEN_NVRAM); 4110 trms1040_wait_30us(io_port); 4111 outb(NVR_SELECT, io_port + TRM_S1040_GEN_NVRAM); 4112 4113 /* Get data bit while falling edge */ 4114 read_byte = inb(io_port + TRM_S1040_GEN_NVRAM); 4115 result <<= 1; 4116 if (read_byte & NVR_BITIN) 4117 result |= 1; 4118 4119 trms1040_wait_30us(io_port); 4120 } 4121 4122 /* Disable chip select */ 4123 outb(0, io_port + TRM_S1040_GEN_NVRAM); 4124 return result; 4125 } 4126 4127 4128 /** 4129 * trms1040_read_all - read all bytes from the eeprom 4130 * 4131 * Read the 128 bytes from the SEEPROM. 4132 * 4133 * @eeprom: where to store the data 4134 * @io_port: the base io port 4135 **/ 4136 static void __devinit trms1040_read_all(struct NvRamType *eeprom, unsigned long io_port) 4137 { 4138 u8 *b_eeprom = (u8 *)eeprom; 4139 u8 addr; 4140 4141 /* Enable SEEPROM */ 4142 outb((inb(io_port + TRM_S1040_GEN_CONTROL) | EN_EEPROM), 4143 io_port + TRM_S1040_GEN_CONTROL); 4144 4145 /* read details */ 4146 for (addr = 0; addr < 128; addr++, b_eeprom++) 4147 *b_eeprom = trms1040_get_data(io_port, addr); 4148 4149 /* Disable SEEPROM */ 4150 outb((inb(io_port + TRM_S1040_GEN_CONTROL) & ~EN_EEPROM), 4151 io_port + TRM_S1040_GEN_CONTROL); 4152 } 4153 4154 4155 4156 /** 4157 * check_eeprom - get and check contents of the eeprom 4158 * 4159 * Read seeprom 128 bytes into the memory provider in eeprom. 4160 * Checks the checksum and if it's not correct it uses a set of default 4161 * values. 4162 * 4163 * @eeprom: caller allocated strcuture to read the eeprom data into 4164 * @io_port: io port to read from 4165 **/ 4166 static void __devinit check_eeprom(struct NvRamType *eeprom, unsigned long io_port) 4167 { 4168 u16 *w_eeprom = (u16 *)eeprom; 4169 u16 w_addr; 4170 u16 cksum; 4171 u32 d_addr; 4172 u32 *d_eeprom; 4173 4174 trms1040_read_all(eeprom, io_port); /* read eeprom */ 4175 4176 cksum = 0; 4177 for (w_addr = 0, w_eeprom = (u16 *)eeprom; w_addr < 64; 4178 w_addr++, w_eeprom++) 4179 cksum += *w_eeprom; 4180 if (cksum != 0x1234) { 4181 /* 4182 * Checksum is wrong. 4183 * Load a set of defaults into the eeprom buffer 4184 */ 4185 dprintkl(KERN_WARNING, 4186 "EEProm checksum error: using default values and options.\n"); 4187 eeprom->sub_vendor_id[0] = (u8)PCI_VENDOR_ID_TEKRAM; 4188 eeprom->sub_vendor_id[1] = (u8)(PCI_VENDOR_ID_TEKRAM >> 8); 4189 eeprom->sub_sys_id[0] = (u8)PCI_DEVICE_ID_TEKRAM_TRMS1040; 4190 eeprom->sub_sys_id[1] = 4191 (u8)(PCI_DEVICE_ID_TEKRAM_TRMS1040 >> 8); 4192 eeprom->sub_class = 0x00; 4193 eeprom->vendor_id[0] = (u8)PCI_VENDOR_ID_TEKRAM; 4194 eeprom->vendor_id[1] = (u8)(PCI_VENDOR_ID_TEKRAM >> 8); 4195 eeprom->device_id[0] = (u8)PCI_DEVICE_ID_TEKRAM_TRMS1040; 4196 eeprom->device_id[1] = 4197 (u8)(PCI_DEVICE_ID_TEKRAM_TRMS1040 >> 8); 4198 eeprom->reserved = 0x00; 4199 4200 for (d_addr = 0, d_eeprom = (u32 *)eeprom->target; 4201 d_addr < 16; d_addr++, d_eeprom++) 4202 *d_eeprom = 0x00000077; /* cfg3,cfg2,period,cfg0 */ 4203 4204 *d_eeprom++ = 0x04000F07; /* max_tag,delay_time,channel_cfg,scsi_id */ 4205 *d_eeprom++ = 0x00000015; /* reserved1,boot_lun,boot_target,reserved0 */ 4206 for (d_addr = 0; d_addr < 12; d_addr++, d_eeprom++) 4207 *d_eeprom = 0x00; 4208 4209 /* Now load defaults (maybe set by boot/module params) */ 4210 set_safe_settings(); 4211 fix_settings(); 4212 eeprom_override(eeprom); 4213 4214 eeprom->cksum = 0x00; 4215 for (w_addr = 0, cksum = 0, w_eeprom = (u16 *)eeprom; 4216 w_addr < 63; w_addr++, w_eeprom++) 4217 cksum += *w_eeprom; 4218 4219 *w_eeprom = 0x1234 - cksum; 4220 trms1040_write_all(eeprom, io_port); 4221 eeprom->delay_time = cfg_data[CFG_RESET_DELAY].value; 4222 } else { 4223 set_safe_settings(); 4224 eeprom_index_to_delay(eeprom); 4225 eeprom_override(eeprom); 4226 } 4227 } 4228 4229 4230 /** 4231 * print_eeprom_settings - output the eeprom settings 4232 * to the kernel log so people can see what they were. 4233 * 4234 * @eeprom: The eeprom data strucutre to show details for. 4235 **/ 4236 static void __devinit print_eeprom_settings(struct NvRamType *eeprom) 4237 { 4238 dprintkl(KERN_INFO, "Used settings: AdapterID=%02i, Speed=%i(%02i.%01iMHz), dev_mode=0x%02x\n", 4239 eeprom->scsi_id, 4240 eeprom->target[0].period, 4241 clock_speed[eeprom->target[0].period] / 10, 4242 clock_speed[eeprom->target[0].period] % 10, 4243 eeprom->target[0].cfg0); 4244 dprintkl(KERN_INFO, " AdaptMode=0x%02x, Tags=%i(%02i), DelayReset=%is\n", 4245 eeprom->channel_cfg, eeprom->max_tag, 4246 1 << eeprom->max_tag, eeprom->delay_time); 4247 } 4248 4249 4250 /* Free SG tables */ 4251 static void adapter_sg_tables_free(struct AdapterCtlBlk *acb) 4252 { 4253 int i; 4254 const unsigned srbs_per_page = PAGE_SIZE/SEGMENTX_LEN; 4255 4256 for (i = 0; i < DC395x_MAX_SRB_CNT; i += srbs_per_page) 4257 kfree(acb->srb_array[i].segment_x); 4258 } 4259 4260 4261 /* 4262 * Allocate SG tables; as we have to pci_map them, an SG list (struct SGentry*) 4263 * should never cross a page boundary */ 4264 static int __devinit adapter_sg_tables_alloc(struct AdapterCtlBlk *acb) 4265 { 4266 const unsigned mem_needed = (DC395x_MAX_SRB_CNT+1) 4267 *SEGMENTX_LEN; 4268 int pages = (mem_needed+(PAGE_SIZE-1))/PAGE_SIZE; 4269 const unsigned srbs_per_page = PAGE_SIZE/SEGMENTX_LEN; 4270 int srb_idx = 0; 4271 unsigned i = 0; 4272 struct SGentry *uninitialized_var(ptr); 4273 4274 for (i = 0; i < DC395x_MAX_SRB_CNT; i++) 4275 acb->srb_array[i].segment_x = NULL; 4276 4277 dprintkdbg(DBG_1, "Allocate %i pages for SG tables\n", pages); 4278 while (pages--) { 4279 ptr = kmalloc(PAGE_SIZE, GFP_KERNEL); 4280 if (!ptr) { 4281 adapter_sg_tables_free(acb); 4282 return 1; 4283 } 4284 dprintkdbg(DBG_1, "Allocate %li bytes at %p for SG segments %i\n", 4285 PAGE_SIZE, ptr, srb_idx); 4286 i = 0; 4287 while (i < srbs_per_page && srb_idx < DC395x_MAX_SRB_CNT) 4288 acb->srb_array[srb_idx++].segment_x = 4289 ptr + (i++ * DC395x_MAX_SG_LISTENTRY); 4290 } 4291 if (i < srbs_per_page) 4292 acb->srb.segment_x = 4293 ptr + (i * DC395x_MAX_SG_LISTENTRY); 4294 else 4295 dprintkl(KERN_DEBUG, "No space for tmsrb SG table reserved?!\n"); 4296 return 0; 4297 } 4298 4299 4300 4301 /** 4302 * adapter_print_config - print adapter connection and termination 4303 * config 4304 * 4305 * The io port in the adapter needs to have been set before calling 4306 * this function. 4307 * 4308 * @acb: The adapter to print the information for. 4309 **/ 4310 static void __devinit adapter_print_config(struct AdapterCtlBlk *acb) 4311 { 4312 u8 bval; 4313 4314 bval = DC395x_read8(acb, TRM_S1040_GEN_STATUS); 4315 dprintkl(KERN_INFO, "%sConnectors: ", 4316 ((bval & WIDESCSI) ? "(Wide) " : "")); 4317 if (!(bval & CON5068)) 4318 printk("ext%s ", !(bval & EXT68HIGH) ? "68" : "50"); 4319 if (!(bval & CON68)) 4320 printk("int68%s ", !(bval & INT68HIGH) ? "" : "(50)"); 4321 if (!(bval & CON50)) 4322 printk("int50 "); 4323 if ((bval & (CON5068 | CON50 | CON68)) == 4324 0 /*(CON5068 | CON50 | CON68) */ ) 4325 printk(" Oops! (All 3?) "); 4326 bval = DC395x_read8(acb, TRM_S1040_GEN_CONTROL); 4327 printk(" Termination: "); 4328 if (bval & DIS_TERM) 4329 printk("Disabled\n"); 4330 else { 4331 if (bval & AUTOTERM) 4332 printk("Auto "); 4333 if (bval & LOW8TERM) 4334 printk("Low "); 4335 if (bval & UP8TERM) 4336 printk("High "); 4337 printk("\n"); 4338 } 4339 } 4340 4341 4342 /** 4343 * adapter_init_params - Initialize the various parameters in the 4344 * adapter structure. Note that the pointer to the scsi_host is set 4345 * early (when this instance is created) and the io_port and irq 4346 * values are set later after they have been reserved. This just gets 4347 * everything set to a good starting position. 4348 * 4349 * The eeprom structure in the adapter needs to have been set before 4350 * calling this function. 4351 * 4352 * @acb: The adapter to initialize. 4353 **/ 4354 static void __devinit adapter_init_params(struct AdapterCtlBlk *acb) 4355 { 4356 struct NvRamType *eeprom = &acb->eeprom; 4357 int i; 4358 4359 /* NOTE: acb->scsi_host is set at scsi_host/acb creation time */ 4360 /* NOTE: acb->io_port_base is set at port registration time */ 4361 /* NOTE: acb->io_port_len is set at port registration time */ 4362 4363 INIT_LIST_HEAD(&acb->dcb_list); 4364 acb->dcb_run_robin = NULL; 4365 acb->active_dcb = NULL; 4366 4367 INIT_LIST_HEAD(&acb->srb_free_list); 4368 /* temp SRB for Q tag used or abort command used */ 4369 acb->tmp_srb = &acb->srb; 4370 init_timer(&acb->waiting_timer); 4371 init_timer(&acb->selto_timer); 4372 4373 acb->srb_count = DC395x_MAX_SRB_CNT; 4374 4375 acb->sel_timeout = DC395x_SEL_TIMEOUT; /* timeout=250ms */ 4376 /* NOTE: acb->irq_level is set at IRQ registration time */ 4377 4378 acb->tag_max_num = 1 << eeprom->max_tag; 4379 if (acb->tag_max_num > 30) 4380 acb->tag_max_num = 30; 4381 4382 acb->acb_flag = 0; /* RESET_DETECT, RESET_DONE, RESET_DEV */ 4383 acb->gmode2 = eeprom->channel_cfg; 4384 acb->config = 0; /* NOTE: actually set in adapter_init_chip */ 4385 4386 if (eeprom->channel_cfg & NAC_SCANLUN) 4387 acb->lun_chk = 1; 4388 acb->scan_devices = 1; 4389 4390 acb->scsi_host->this_id = eeprom->scsi_id; 4391 acb->hostid_bit = (1 << acb->scsi_host->this_id); 4392 4393 for (i = 0; i < DC395x_MAX_SCSI_ID; i++) 4394 acb->dcb_map[i] = 0; 4395 4396 acb->msg_len = 0; 4397 4398 /* link static array of srbs into the srb free list */ 4399 for (i = 0; i < acb->srb_count - 1; i++) 4400 srb_free_insert(acb, &acb->srb_array[i]); 4401 } 4402 4403 4404 /** 4405 * adapter_init_host - Initialize the scsi host instance based on 4406 * values that we have already stored in the adapter instance. There's 4407 * some mention that a lot of these are deprecated, so we won't use 4408 * them (we'll use the ones in the adapter instance) but we'll fill 4409 * them in in case something else needs them. 4410 * 4411 * The eeprom structure, irq and io ports in the adapter need to have 4412 * been set before calling this function. 4413 * 4414 * @host: The scsi host instance to fill in the values for. 4415 **/ 4416 static void __devinit adapter_init_scsi_host(struct Scsi_Host *host) 4417 { 4418 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)host->hostdata; 4419 struct NvRamType *eeprom = &acb->eeprom; 4420 4421 host->max_cmd_len = 24; 4422 host->can_queue = DC395x_MAX_CMD_QUEUE; 4423 host->cmd_per_lun = DC395x_MAX_CMD_PER_LUN; 4424 host->this_id = (int)eeprom->scsi_id; 4425 host->io_port = acb->io_port_base; 4426 host->n_io_port = acb->io_port_len; 4427 host->dma_channel = -1; 4428 host->unique_id = acb->io_port_base; 4429 host->irq = acb->irq_level; 4430 host->last_reset = jiffies; 4431 4432 host->max_id = 16; 4433 if (host->max_id - 1 == eeprom->scsi_id) 4434 host->max_id--; 4435 4436 #ifdef CONFIG_SCSI_MULTI_LUN 4437 if (eeprom->channel_cfg & NAC_SCANLUN) 4438 host->max_lun = 8; 4439 else 4440 host->max_lun = 1; 4441 #else 4442 host->max_lun = 1; 4443 #endif 4444 4445 } 4446 4447 4448 /** 4449 * adapter_init_chip - Get the chip into a know state and figure out 4450 * some of the settings that apply to this adapter. 4451 * 4452 * The io port in the adapter needs to have been set before calling 4453 * this function. The config will be configured correctly on return. 4454 * 4455 * @acb: The adapter which we are to init. 4456 **/ 4457 static void __devinit adapter_init_chip(struct AdapterCtlBlk *acb) 4458 { 4459 struct NvRamType *eeprom = &acb->eeprom; 4460 4461 /* Mask all the interrupt */ 4462 DC395x_write8(acb, TRM_S1040_DMA_INTEN, 0x00); 4463 DC395x_write8(acb, TRM_S1040_SCSI_INTEN, 0x00); 4464 4465 /* Reset SCSI module */ 4466 DC395x_write16(acb, TRM_S1040_SCSI_CONTROL, DO_RSTMODULE); 4467 4468 /* Reset PCI/DMA module */ 4469 DC395x_write8(acb, TRM_S1040_DMA_CONTROL, DMARESETMODULE); 4470 udelay(20); 4471 4472 /* program configuration 0 */ 4473 acb->config = HCC_AUTOTERM | HCC_PARITY; 4474 if (DC395x_read8(acb, TRM_S1040_GEN_STATUS) & WIDESCSI) 4475 acb->config |= HCC_WIDE_CARD; 4476 4477 if (eeprom->channel_cfg & NAC_POWERON_SCSI_RESET) 4478 acb->config |= HCC_SCSI_RESET; 4479 4480 if (acb->config & HCC_SCSI_RESET) { 4481 dprintkl(KERN_INFO, "Performing initial SCSI bus reset\n"); 4482 DC395x_write8(acb, TRM_S1040_SCSI_CONTROL, DO_RSTSCSI); 4483 4484 /*while (!( DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS) & INT_SCSIRESET )); */ 4485 /*spin_unlock_irq (&io_request_lock); */ 4486 udelay(500); 4487 4488 acb->scsi_host->last_reset = 4489 jiffies + HZ / 2 + 4490 HZ * acb->eeprom.delay_time; 4491 4492 /*spin_lock_irq (&io_request_lock); */ 4493 } 4494 } 4495 4496 4497 /** 4498 * init_adapter - Grab the resource for the card, setup the adapter 4499 * information, set the card into a known state, create the various 4500 * tables etc etc. This basically gets all adapter information all up 4501 * to date, initialised and gets the chip in sync with it. 4502 * 4503 * @host: This hosts adapter structure 4504 * @io_port: The base I/O port 4505 * @irq: IRQ 4506 * 4507 * Returns 0 if the initialization succeeds, any other value on 4508 * failure. 4509 **/ 4510 static int __devinit adapter_init(struct AdapterCtlBlk *acb, 4511 unsigned long io_port, u32 io_port_len, unsigned int irq) 4512 { 4513 if (!request_region(io_port, io_port_len, DC395X_NAME)) { 4514 dprintkl(KERN_ERR, "Failed to reserve IO region 0x%lx\n", io_port); 4515 goto failed; 4516 } 4517 /* store port base to indicate we have registered it */ 4518 acb->io_port_base = io_port; 4519 acb->io_port_len = io_port_len; 4520 4521 if (request_irq(irq, dc395x_interrupt, IRQF_SHARED, DC395X_NAME, acb)) { 4522 /* release the region we just claimed */ 4523 dprintkl(KERN_INFO, "Failed to register IRQ\n"); 4524 goto failed; 4525 } 4526 /* store irq to indicate we have registered it */ 4527 acb->irq_level = irq; 4528 4529 /* get eeprom configuration information and command line settings etc */ 4530 check_eeprom(&acb->eeprom, io_port); 4531 print_eeprom_settings(&acb->eeprom); 4532 4533 /* setup adapter control block */ 4534 adapter_init_params(acb); 4535 4536 /* display card connectors/termination settings */ 4537 adapter_print_config(acb); 4538 4539 if (adapter_sg_tables_alloc(acb)) { 4540 dprintkl(KERN_DEBUG, "Memory allocation for SG tables failed\n"); 4541 goto failed; 4542 } 4543 adapter_init_scsi_host(acb->scsi_host); 4544 adapter_init_chip(acb); 4545 set_basic_config(acb); 4546 4547 dprintkdbg(DBG_0, 4548 "adapter_init: acb=%p, pdcb_map=%p psrb_array=%p " 4549 "size{acb=0x%04x dcb=0x%04x srb=0x%04x}\n", 4550 acb, acb->dcb_map, acb->srb_array, sizeof(struct AdapterCtlBlk), 4551 sizeof(struct DeviceCtlBlk), sizeof(struct ScsiReqBlk)); 4552 return 0; 4553 4554 failed: 4555 if (acb->irq_level) 4556 free_irq(acb->irq_level, acb); 4557 if (acb->io_port_base) 4558 release_region(acb->io_port_base, acb->io_port_len); 4559 adapter_sg_tables_free(acb); 4560 4561 return 1; 4562 } 4563 4564 4565 /** 4566 * adapter_uninit_chip - cleanly shut down the scsi controller chip, 4567 * stopping all operations and disabling interrupt generation on the 4568 * card. 4569 * 4570 * @acb: The adapter which we are to shutdown. 4571 **/ 4572 static void adapter_uninit_chip(struct AdapterCtlBlk *acb) 4573 { 4574 /* disable interrupts */ 4575 DC395x_write8(acb, TRM_S1040_DMA_INTEN, 0); 4576 DC395x_write8(acb, TRM_S1040_SCSI_INTEN, 0); 4577 4578 /* reset the scsi bus */ 4579 if (acb->config & HCC_SCSI_RESET) 4580 reset_scsi_bus(acb); 4581 4582 /* clear any pending interrupt state */ 4583 DC395x_read8(acb, TRM_S1040_SCSI_INTSTATUS); 4584 } 4585 4586 4587 4588 /** 4589 * adapter_uninit - Shut down the chip and release any resources that 4590 * we had allocated. Once this returns the adapter should not be used 4591 * anymore. 4592 * 4593 * @acb: The adapter which we are to un-initialize. 4594 **/ 4595 static void adapter_uninit(struct AdapterCtlBlk *acb) 4596 { 4597 unsigned long flags; 4598 DC395x_LOCK_IO(acb->scsi_host, flags); 4599 4600 /* remove timers */ 4601 if (timer_pending(&acb->waiting_timer)) 4602 del_timer(&acb->waiting_timer); 4603 if (timer_pending(&acb->selto_timer)) 4604 del_timer(&acb->selto_timer); 4605 4606 adapter_uninit_chip(acb); 4607 adapter_remove_and_free_all_devices(acb); 4608 DC395x_UNLOCK_IO(acb->scsi_host, flags); 4609 4610 if (acb->irq_level) 4611 free_irq(acb->irq_level, acb); 4612 if (acb->io_port_base) 4613 release_region(acb->io_port_base, acb->io_port_len); 4614 4615 adapter_sg_tables_free(acb); 4616 } 4617 4618 4619 #undef SPRINTF 4620 #define SPRINTF(args...) pos += sprintf(pos, args) 4621 4622 #undef YESNO 4623 #define YESNO(YN) \ 4624 if (YN) SPRINTF(" Yes ");\ 4625 else SPRINTF(" No ") 4626 4627 static int dc395x_proc_info(struct Scsi_Host *host, char *buffer, 4628 char **start, off_t offset, int length, int inout) 4629 { 4630 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)host->hostdata; 4631 int spd, spd1; 4632 char *pos = buffer; 4633 struct DeviceCtlBlk *dcb; 4634 unsigned long flags; 4635 int dev; 4636 4637 if (inout) /* Has data been written to the file ? */ 4638 return -EPERM; 4639 4640 SPRINTF(DC395X_BANNER " PCI SCSI Host Adapter\n"); 4641 SPRINTF(" Driver Version " DC395X_VERSION "\n"); 4642 4643 DC395x_LOCK_IO(acb->scsi_host, flags); 4644 4645 SPRINTF("SCSI Host Nr %i, ", host->host_no); 4646 SPRINTF("DC395U/UW/F DC315/U %s\n", 4647 (acb->config & HCC_WIDE_CARD) ? "Wide" : ""); 4648 SPRINTF("io_port_base 0x%04lx, ", acb->io_port_base); 4649 SPRINTF("irq_level 0x%04x, ", acb->irq_level); 4650 SPRINTF(" SelTimeout %ims\n", (1638 * acb->sel_timeout) / 1000); 4651 4652 SPRINTF("MaxID %i, MaxLUN %i, ", host->max_id, host->max_lun); 4653 SPRINTF("AdapterID %i\n", host->this_id); 4654 4655 SPRINTF("tag_max_num %i", acb->tag_max_num); 4656 /*SPRINTF(", DMA_Status %i\n", DC395x_read8(acb, TRM_S1040_DMA_STATUS)); */ 4657 SPRINTF(", FilterCfg 0x%02x", 4658 DC395x_read8(acb, TRM_S1040_SCSI_CONFIG1)); 4659 SPRINTF(", DelayReset %is\n", acb->eeprom.delay_time); 4660 /*SPRINTF("\n"); */ 4661 4662 SPRINTF("Nr of DCBs: %i\n", list_size(&acb->dcb_list)); 4663 SPRINTF 4664 ("Map of attached LUNs: %02x %02x %02x %02x %02x %02x %02x %02x\n", 4665 acb->dcb_map[0], acb->dcb_map[1], acb->dcb_map[2], 4666 acb->dcb_map[3], acb->dcb_map[4], acb->dcb_map[5], 4667 acb->dcb_map[6], acb->dcb_map[7]); 4668 SPRINTF 4669 (" %02x %02x %02x %02x %02x %02x %02x %02x\n", 4670 acb->dcb_map[8], acb->dcb_map[9], acb->dcb_map[10], 4671 acb->dcb_map[11], acb->dcb_map[12], acb->dcb_map[13], 4672 acb->dcb_map[14], acb->dcb_map[15]); 4673 4674 SPRINTF 4675 ("Un ID LUN Prty Sync Wide DsCn SndS TagQ nego_period SyncFreq SyncOffs MaxCmd\n"); 4676 4677 dev = 0; 4678 list_for_each_entry(dcb, &acb->dcb_list, list) { 4679 int nego_period; 4680 SPRINTF("%02i %02i %02i ", dev, dcb->target_id, 4681 dcb->target_lun); 4682 YESNO(dcb->dev_mode & NTC_DO_PARITY_CHK); 4683 YESNO(dcb->sync_offset); 4684 YESNO(dcb->sync_period & WIDE_SYNC); 4685 YESNO(dcb->dev_mode & NTC_DO_DISCONNECT); 4686 YESNO(dcb->dev_mode & NTC_DO_SEND_START); 4687 YESNO(dcb->sync_mode & EN_TAG_QUEUEING); 4688 nego_period = clock_period[dcb->sync_period & 0x07] << 2; 4689 if (dcb->sync_offset) 4690 SPRINTF(" %03i ns ", nego_period); 4691 else 4692 SPRINTF(" (%03i ns)", (dcb->min_nego_period << 2)); 4693 4694 if (dcb->sync_offset & 0x0f) { 4695 spd = 1000 / (nego_period); 4696 spd1 = 1000 % (nego_period); 4697 spd1 = (spd1 * 10 + nego_period / 2) / (nego_period); 4698 SPRINTF(" %2i.%1i M %02i ", spd, spd1, 4699 (dcb->sync_offset & 0x0f)); 4700 } else 4701 SPRINTF(" "); 4702 4703 /* Add more info ... */ 4704 SPRINTF(" %02i\n", dcb->max_command); 4705 dev++; 4706 } 4707 4708 if (timer_pending(&acb->waiting_timer)) 4709 SPRINTF("Waiting queue timer running\n"); 4710 else 4711 SPRINTF("\n"); 4712 4713 list_for_each_entry(dcb, &acb->dcb_list, list) { 4714 struct ScsiReqBlk *srb; 4715 if (!list_empty(&dcb->srb_waiting_list)) 4716 SPRINTF("DCB (%02i-%i): Waiting: %i:", 4717 dcb->target_id, dcb->target_lun, 4718 list_size(&dcb->srb_waiting_list)); 4719 list_for_each_entry(srb, &dcb->srb_waiting_list, list) 4720 SPRINTF(" %li", srb->cmd->serial_number); 4721 if (!list_empty(&dcb->srb_going_list)) 4722 SPRINTF("\nDCB (%02i-%i): Going : %i:", 4723 dcb->target_id, dcb->target_lun, 4724 list_size(&dcb->srb_going_list)); 4725 list_for_each_entry(srb, &dcb->srb_going_list, list) 4726 SPRINTF(" %li", srb->cmd->serial_number); 4727 if (!list_empty(&dcb->srb_waiting_list) || !list_empty(&dcb->srb_going_list)) 4728 SPRINTF("\n"); 4729 } 4730 4731 if (debug_enabled(DBG_1)) { 4732 SPRINTF("DCB list for ACB %p:\n", acb); 4733 list_for_each_entry(dcb, &acb->dcb_list, list) { 4734 SPRINTF("%p -> ", dcb); 4735 } 4736 SPRINTF("END\n"); 4737 } 4738 4739 *start = buffer + offset; 4740 DC395x_UNLOCK_IO(acb->scsi_host, flags); 4741 4742 if (pos - buffer < offset) 4743 return 0; 4744 else if (pos - buffer - offset < length) 4745 return pos - buffer - offset; 4746 else 4747 return length; 4748 } 4749 4750 4751 static struct scsi_host_template dc395x_driver_template = { 4752 .module = THIS_MODULE, 4753 .proc_name = DC395X_NAME, 4754 .proc_info = dc395x_proc_info, 4755 .name = DC395X_BANNER " " DC395X_VERSION, 4756 .queuecommand = dc395x_queue_command, 4757 .bios_param = dc395x_bios_param, 4758 .slave_alloc = dc395x_slave_alloc, 4759 .slave_destroy = dc395x_slave_destroy, 4760 .can_queue = DC395x_MAX_CAN_QUEUE, 4761 .this_id = 7, 4762 .sg_tablesize = DC395x_MAX_SG_TABLESIZE, 4763 .cmd_per_lun = DC395x_MAX_CMD_PER_LUN, 4764 .eh_abort_handler = dc395x_eh_abort, 4765 .eh_bus_reset_handler = dc395x_eh_bus_reset, 4766 .use_clustering = DISABLE_CLUSTERING, 4767 }; 4768 4769 4770 /** 4771 * banner_display - Display banner on first instance of driver 4772 * initialized. 4773 **/ 4774 static void banner_display(void) 4775 { 4776 static int banner_done = 0; 4777 if (!banner_done) 4778 { 4779 dprintkl(KERN_INFO, "%s %s\n", DC395X_BANNER, DC395X_VERSION); 4780 banner_done = 1; 4781 } 4782 } 4783 4784 4785 /** 4786 * dc395x_init_one - Initialise a single instance of the adapter. 4787 * 4788 * The PCI layer will call this once for each instance of the adapter 4789 * that it finds in the system. The pci_dev strcuture indicates which 4790 * instance we are being called from. 4791 * 4792 * @dev: The PCI device to initialize. 4793 * @id: Looks like a pointer to the entry in our pci device table 4794 * that was actually matched by the PCI subsystem. 4795 * 4796 * Returns 0 on success, or an error code (-ve) on failure. 4797 **/ 4798 static int __devinit dc395x_init_one(struct pci_dev *dev, 4799 const struct pci_device_id *id) 4800 { 4801 struct Scsi_Host *scsi_host = NULL; 4802 struct AdapterCtlBlk *acb = NULL; 4803 unsigned long io_port_base; 4804 unsigned int io_port_len; 4805 unsigned int irq; 4806 4807 dprintkdbg(DBG_0, "Init one instance (%s)\n", pci_name(dev)); 4808 banner_display(); 4809 4810 if (pci_enable_device(dev)) 4811 { 4812 dprintkl(KERN_INFO, "PCI Enable device failed.\n"); 4813 return -ENODEV; 4814 } 4815 io_port_base = pci_resource_start(dev, 0) & PCI_BASE_ADDRESS_IO_MASK; 4816 io_port_len = pci_resource_len(dev, 0); 4817 irq = dev->irq; 4818 dprintkdbg(DBG_0, "IO_PORT=0x%04lx, IRQ=0x%x\n", io_port_base, dev->irq); 4819 4820 /* allocate scsi host information (includes out adapter) */ 4821 scsi_host = scsi_host_alloc(&dc395x_driver_template, 4822 sizeof(struct AdapterCtlBlk)); 4823 if (!scsi_host) { 4824 dprintkl(KERN_INFO, "scsi_host_alloc failed\n"); 4825 goto fail; 4826 } 4827 acb = (struct AdapterCtlBlk*)scsi_host->hostdata; 4828 acb->scsi_host = scsi_host; 4829 acb->dev = dev; 4830 4831 /* initialise the adapter and everything we need */ 4832 if (adapter_init(acb, io_port_base, io_port_len, irq)) { 4833 dprintkl(KERN_INFO, "adapter init failed\n"); 4834 goto fail; 4835 } 4836 4837 pci_set_master(dev); 4838 4839 /* get the scsi mid level to scan for new devices on the bus */ 4840 if (scsi_add_host(scsi_host, &dev->dev)) { 4841 dprintkl(KERN_ERR, "scsi_add_host failed\n"); 4842 goto fail; 4843 } 4844 pci_set_drvdata(dev, scsi_host); 4845 scsi_scan_host(scsi_host); 4846 4847 return 0; 4848 4849 fail: 4850 if (acb != NULL) 4851 adapter_uninit(acb); 4852 if (scsi_host != NULL) 4853 scsi_host_put(scsi_host); 4854 pci_disable_device(dev); 4855 return -ENODEV; 4856 } 4857 4858 4859 /** 4860 * dc395x_remove_one - Called to remove a single instance of the 4861 * adapter. 4862 * 4863 * @dev: The PCI device to initialize. 4864 **/ 4865 static void __devexit dc395x_remove_one(struct pci_dev *dev) 4866 { 4867 struct Scsi_Host *scsi_host = pci_get_drvdata(dev); 4868 struct AdapterCtlBlk *acb = (struct AdapterCtlBlk *)(scsi_host->hostdata); 4869 4870 dprintkdbg(DBG_0, "dc395x_remove_one: acb=%p\n", acb); 4871 4872 scsi_remove_host(scsi_host); 4873 adapter_uninit(acb); 4874 pci_disable_device(dev); 4875 scsi_host_put(scsi_host); 4876 pci_set_drvdata(dev, NULL); 4877 } 4878 4879 4880 static struct pci_device_id dc395x_pci_table[] = { 4881 { 4882 .vendor = PCI_VENDOR_ID_TEKRAM, 4883 .device = PCI_DEVICE_ID_TEKRAM_TRMS1040, 4884 .subvendor = PCI_ANY_ID, 4885 .subdevice = PCI_ANY_ID, 4886 }, 4887 {} /* Terminating entry */ 4888 }; 4889 MODULE_DEVICE_TABLE(pci, dc395x_pci_table); 4890 4891 4892 static struct pci_driver dc395x_driver = { 4893 .name = DC395X_NAME, 4894 .id_table = dc395x_pci_table, 4895 .probe = dc395x_init_one, 4896 .remove = __devexit_p(dc395x_remove_one), 4897 }; 4898 4899 4900 /** 4901 * dc395x_module_init - Module initialization function 4902 * 4903 * Used by both module and built-in driver to initialise this driver. 4904 **/ 4905 static int __init dc395x_module_init(void) 4906 { 4907 return pci_register_driver(&dc395x_driver); 4908 } 4909 4910 4911 /** 4912 * dc395x_module_exit - Module cleanup function. 4913 **/ 4914 static void __exit dc395x_module_exit(void) 4915 { 4916 pci_unregister_driver(&dc395x_driver); 4917 } 4918 4919 4920 module_init(dc395x_module_init); 4921 module_exit(dc395x_module_exit); 4922 4923 MODULE_AUTHOR("C.L. Huang / Erich Chen / Kurt Garloff"); 4924 MODULE_DESCRIPTION("SCSI host adapter driver for Tekram TRM-S1040 based adapters: Tekram DC395 and DC315 series"); 4925 MODULE_LICENSE("GPL"); 4926