1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * linux/drivers/acorn/scsi/fas216.h 4 * 5 * Copyright (C) 1997-2000 Russell King 6 * 7 * FAS216 generic driver 8 */ 9 #ifndef FAS216_H 10 #define FAS216_H 11 12 #include <scsi/scsi_eh.h> 13 14 #include "queue.h" 15 #include "msgqueue.h" 16 17 /* FAS register definitions */ 18 19 /* transfer count low */ 20 #define REG_CTCL (0) 21 #define REG_STCL (0) 22 23 /* transfer count medium */ 24 #define REG_CTCM (1) 25 #define REG_STCM (1) 26 27 /* fifo data */ 28 #define REG_FF (2) 29 30 /* command */ 31 #define REG_CMD (3) 32 #define CMD_NOP 0x00 33 #define CMD_FLUSHFIFO 0x01 34 #define CMD_RESETCHIP 0x02 35 #define CMD_RESETSCSI 0x03 36 37 #define CMD_TRANSFERINFO 0x10 38 #define CMD_INITCMDCOMPLETE 0x11 39 #define CMD_MSGACCEPTED 0x12 40 #define CMD_PADBYTES 0x18 41 #define CMD_SETATN 0x1a 42 #define CMD_RSETATN 0x1b 43 44 #define CMD_SELECTWOATN 0x41 45 #define CMD_SELECTATN 0x42 46 #define CMD_SELECTATNSTOP 0x43 47 #define CMD_ENABLESEL 0x44 48 #define CMD_DISABLESEL 0x45 49 #define CMD_SELECTATN3 0x46 50 #define CMD_RESEL3 0x47 51 52 #define CMD_WITHDMA 0x80 53 54 /* status register (read) */ 55 #define REG_STAT (4) 56 #define STAT_IO (1 << 0) /* IO phase */ 57 #define STAT_CD (1 << 1) /* CD phase */ 58 #define STAT_MSG (1 << 2) /* MSG phase */ 59 #define STAT_TRANSFERDONE (1 << 3) /* Transfer completed */ 60 #define STAT_TRANSFERCNTZ (1 << 4) /* Transfer counter is zero */ 61 #define STAT_PARITYERROR (1 << 5) /* Parity error */ 62 #define STAT_REALBAD (1 << 6) /* Something bad */ 63 #define STAT_INT (1 << 7) /* Interrupt */ 64 65 #define STAT_BUSMASK (STAT_MSG|STAT_CD|STAT_IO) 66 #define STAT_DATAOUT (0) /* Data out */ 67 #define STAT_DATAIN (STAT_IO) /* Data in */ 68 #define STAT_COMMAND (STAT_CD) /* Command out */ 69 #define STAT_STATUS (STAT_CD|STAT_IO) /* Status In */ 70 #define STAT_MESGOUT (STAT_MSG|STAT_CD) /* Message out */ 71 #define STAT_MESGIN (STAT_MSG|STAT_CD|STAT_IO) /* Message In */ 72 73 /* bus ID for select / reselect */ 74 #define REG_SDID (4) 75 #define BUSID(target) ((target) & 7) 76 77 /* Interrupt status register (read) */ 78 #define REG_INST (5) 79 #define INST_SELWOATN (1 << 0) /* Select w/o ATN */ 80 #define INST_SELATN (1 << 1) /* Select w/ATN */ 81 #define INST_RESELECTED (1 << 2) /* Reselected */ 82 #define INST_FUNCDONE (1 << 3) /* Function done */ 83 #define INST_BUSSERVICE (1 << 4) /* Bus service */ 84 #define INST_DISCONNECT (1 << 5) /* Disconnect */ 85 #define INST_ILLEGALCMD (1 << 6) /* Illegal command */ 86 #define INST_BUSRESET (1 << 7) /* SCSI Bus reset */ 87 88 /* Timeout register (write) */ 89 #define REG_STIM (5) 90 91 /* Sequence step register (read) */ 92 #define REG_IS (6) 93 #define IS_BITS 0x07 94 #define IS_SELARB 0x00 /* Select & Arb ok */ 95 #define IS_MSGBYTESENT 0x01 /* One byte message sent*/ 96 #define IS_NOTCOMMAND 0x02 /* Not in command state */ 97 #define IS_EARLYPHASE 0x03 /* Early phase change */ 98 #define IS_COMPLETE 0x04 /* Command ok */ 99 #define IS_SOF 0x08 /* Sync off flag */ 100 101 /* Transfer period step (write) */ 102 #define REG_STP (6) 103 104 /* Synchronous Offset (write) */ 105 #define REG_SOF (7) 106 107 /* Fifo state register (read) */ 108 #define REG_CFIS (7) 109 #define CFIS_CF 0x1f /* Num bytes in FIFO */ 110 #define CFIS_IS 0xe0 /* Step */ 111 112 /* config register 1 */ 113 #define REG_CNTL1 (8) 114 #define CNTL1_CID (7 << 0) /* Chip ID */ 115 #define CNTL1_STE (1 << 3) /* Self test enable */ 116 #define CNTL1_PERE (1 << 4) /* Parity enable reporting en. */ 117 #define CNTL1_PTE (1 << 5) /* Parity test enable */ 118 #define CNTL1_DISR (1 << 6) /* Disable Irq on SCSI reset */ 119 #define CNTL1_ETM (1 << 7) /* Extended Timing Mode */ 120 121 /* Clock conversion factor (read) */ 122 #define REG_CLKF (9) 123 #define CLKF_F37MHZ 0x00 /* 35.01 - 40 MHz */ 124 #define CLKF_F10MHZ 0x02 /* 10 MHz */ 125 #define CLKF_F12MHZ 0x03 /* 10.01 - 15 MHz */ 126 #define CLKF_F17MHZ 0x04 /* 15.01 - 20 MHz */ 127 #define CLKF_F22MHZ 0x05 /* 20.01 - 25 MHz */ 128 #define CLKF_F27MHZ 0x06 /* 25.01 - 30 MHz */ 129 #define CLKF_F32MHZ 0x07 /* 30.01 - 35 MHz */ 130 131 /* Chip test register (write) */ 132 #define REG_FTM (10) 133 #define TEST_FTM 0x01 /* Force target mode */ 134 #define TEST_FIM 0x02 /* Force initiator mode */ 135 #define TEST_FHI 0x04 /* Force high impedance mode */ 136 137 /* Configuration register 2 (read/write) */ 138 #define REG_CNTL2 (11) 139 #define CNTL2_PGDP (1 << 0) /* Pass Th/Generate Data Parity */ 140 #define CNTL2_PGRP (1 << 1) /* Pass Th/Generate Reg Parity */ 141 #define CNTL2_ACDPE (1 << 2) /* Abort on Cmd/Data Parity Err */ 142 #define CNTL2_S2FE (1 << 3) /* SCSI2 Features Enable */ 143 #define CNTL2_TSDR (1 << 4) /* Tristate DREQ */ 144 #define CNTL2_SBO (1 << 5) /* Select Byte Order */ 145 #define CNTL2_ENF (1 << 6) /* Enable features */ 146 #define CNTL2_DAE (1 << 7) /* Data Alignment Enable */ 147 148 /* Configuration register 3 (read/write) */ 149 #define REG_CNTL3 (12) 150 #define CNTL3_BS8 (1 << 0) /* Burst size 8 */ 151 #define CNTL3_MDM (1 << 1) /* Modify DMA mode */ 152 #define CNTL3_LBTM (1 << 2) /* Last Byte Transfer mode */ 153 #define CNTL3_FASTCLK (1 << 3) /* Fast SCSI clocking */ 154 #define CNTL3_FASTSCSI (1 << 4) /* Fast SCSI */ 155 #define CNTL3_G2CB (1 << 5) /* Group2 SCSI support */ 156 #define CNTL3_QTAG (1 << 6) /* Enable 3 byte msgs */ 157 #define CNTL3_ADIDCHK (1 << 7) /* Additional ID check */ 158 159 /* High transfer count (read/write) */ 160 #define REG_CTCH (14) 161 #define REG_STCH (14) 162 163 /* ID register (read only) */ 164 #define REG_ID (14) 165 166 /* Data alignment */ 167 #define REG_DAL (15) 168 169 typedef enum { 170 PHASE_IDLE, /* we're not planning on doing anything */ 171 PHASE_SELECTION, /* selecting a device */ 172 PHASE_SELSTEPS, /* selection with command steps */ 173 PHASE_COMMAND, /* command sent */ 174 PHASE_MESSAGESENT, /* selected, and we're sending cmd */ 175 PHASE_DATAOUT, /* data out to device */ 176 PHASE_DATAIN, /* data in from device */ 177 PHASE_MSGIN, /* message in from device */ 178 PHASE_MSGIN_DISCONNECT, /* disconnecting from bus */ 179 PHASE_MSGOUT, /* after message out phase */ 180 PHASE_MSGOUT_EXPECT, /* expecting message out */ 181 PHASE_STATUS, /* status from device */ 182 PHASE_DONE /* Command complete */ 183 } phase_t; 184 185 typedef enum { 186 DMA_OUT, /* DMA from memory to chip */ 187 DMA_IN /* DMA from chip to memory */ 188 } fasdmadir_t; 189 190 typedef enum { 191 fasdma_none, /* No dma */ 192 fasdma_pio, /* PIO mode */ 193 fasdma_pseudo, /* Pseudo DMA */ 194 fasdma_real_block, /* Real DMA, on block by block basis */ 195 fasdma_real_all /* Real DMA, on request by request */ 196 } fasdmatype_t; 197 198 typedef enum { 199 neg_wait, /* Negotiate with device */ 200 neg_inprogress, /* Negotiation sent */ 201 neg_complete, /* Negotiation complete */ 202 neg_targcomplete, /* Target completed negotiation */ 203 neg_invalid /* Negotiation not supported */ 204 } neg_t; 205 206 #define MAGIC 0x441296bdUL 207 #define NR_MSGS 8 208 209 #define FASCAP_DMA (1 << 0) 210 #define FASCAP_PSEUDODMA (1 << 1) 211 212 typedef struct { 213 unsigned long magic_start; 214 spinlock_t host_lock; 215 struct Scsi_Host *host; /* host */ 216 struct scsi_cmnd *SCpnt; /* currently processing command */ 217 struct scsi_cmnd *origSCpnt; /* original connecting command */ 218 struct scsi_cmnd *reqSCpnt; /* request sense command */ 219 struct scsi_cmnd *rstSCpnt; /* reset command */ 220 struct scsi_cmnd *pending_SCpnt[8]; /* per-device pending commands */ 221 int next_pending; /* next pending device */ 222 223 /* 224 * Error recovery 225 */ 226 wait_queue_head_t eh_wait; 227 struct timer_list eh_timer; 228 unsigned int rst_dev_status; 229 unsigned int rst_bus_status; 230 231 /* driver information */ 232 struct { 233 phase_t phase; /* current phase */ 234 void __iomem *io_base; /* iomem base of FAS216 */ 235 unsigned int io_shift; /* shift to adjust reg offsets by */ 236 unsigned char cfg[4]; /* configuration registers */ 237 const char *type; /* chip type */ 238 unsigned int irq; /* interrupt */ 239 int dma; /* dma channel */ 240 241 struct scsi_pointer SCp; /* current commands data pointer */ 242 243 MsgQueue_t msgs; /* message queue for connected device */ 244 245 unsigned int async_stp; /* Async transfer STP value */ 246 unsigned char msgin_fifo; /* bytes in fifo at time of message in */ 247 unsigned char message[256]; /* last message received from device */ 248 249 unsigned char disconnectable:1; /* this command can be disconnected */ 250 unsigned char aborting:1; /* aborting command */ 251 } scsi; 252 253 /* statistics information */ 254 struct { 255 unsigned int queues; 256 unsigned int removes; 257 unsigned int fins; 258 unsigned int reads; 259 unsigned int writes; 260 unsigned int miscs; 261 unsigned int disconnects; 262 unsigned int aborts; 263 unsigned int bus_resets; 264 unsigned int host_resets; 265 } stats; 266 267 /* configuration information */ 268 struct { 269 unsigned char clockrate; /* clock rate of FAS device (MHz) */ 270 unsigned char select_timeout; /* timeout (R5) */ 271 unsigned char sync_max_depth; /* Synchronous xfer max fifo depth */ 272 unsigned char wide_max_size; /* Maximum wide transfer size */ 273 unsigned char cntl3; /* Control Reg 3 */ 274 unsigned int asyncperiod; /* Async transfer period (ns) */ 275 unsigned int capabilities; /* driver capabilities */ 276 unsigned int disconnect_ok:1; /* Disconnects allowed? */ 277 } ifcfg; 278 279 /* queue handling */ 280 struct { 281 Queue_t issue; /* issue queue */ 282 Queue_t disconnected; /* disconnected command queue */ 283 } queues; 284 285 /* per-device info */ 286 struct fas216_device { 287 unsigned char disconnect_ok:1; /* device can disconnect */ 288 unsigned char parity_enabled:1; /* parity checking enabled */ 289 unsigned char parity_check:1; /* need to check parity checking */ 290 unsigned char period; /* sync xfer period in (*4ns) */ 291 unsigned char stp; /* synchronous transfer period */ 292 unsigned char sof; /* synchronous offset register */ 293 unsigned char wide_xfer; /* currently negociated wide transfer */ 294 neg_t sync_state; /* synchronous transfer mode */ 295 neg_t wide_state; /* wide transfer mode */ 296 } device[8]; 297 unsigned long busyluns[64/sizeof(unsigned long)];/* array of bits indicating LUNs busy */ 298 299 /* dma */ 300 struct { 301 fasdmatype_t transfer_type; /* current type of DMA transfer */ 302 fasdmatype_t (*setup) (struct Scsi_Host *host, struct scsi_pointer *SCp, fasdmadir_t direction, fasdmatype_t min_dma); 303 void (*pseudo)(struct Scsi_Host *host, struct scsi_pointer *SCp, fasdmadir_t direction, int transfer); 304 void (*stop) (struct Scsi_Host *host, struct scsi_pointer *SCp); 305 } dma; 306 307 /* miscellaneous */ 308 int internal_done; /* flag to indicate request done */ 309 struct scsi_eh_save ses; /* holds request sense restore info */ 310 unsigned long magic_end; 311 } FAS216_Info; 312 313 /* driver-private data per SCSI command. */ 314 struct fas216_cmd_priv { 315 /* 316 * @scsi_pointer must be the first member. See also arm_scsi_pointer(). 317 */ 318 struct scsi_pointer scsi_pointer; 319 void (*scsi_done)(struct scsi_cmnd *cmd); 320 }; 321 322 static inline struct fas216_cmd_priv *fas216_cmd_priv(struct scsi_cmnd *cmd) 323 { 324 return scsi_cmd_priv(cmd); 325 } 326 327 /* Function: int fas216_init (struct Scsi_Host *instance) 328 * Purpose : initialise FAS/NCR/AMD SCSI structures. 329 * Params : instance - a driver-specific filled-out structure 330 * Returns : 0 on success 331 */ 332 extern int fas216_init (struct Scsi_Host *instance); 333 334 /* Function: int fas216_add (struct Scsi_Host *instance, struct device *dev) 335 * Purpose : initialise FAS/NCR/AMD SCSI ic. 336 * Params : instance - a driver-specific filled-out structure 337 * Returns : 0 on success 338 */ 339 extern int fas216_add (struct Scsi_Host *instance, struct device *dev); 340 341 /* Function: int fas216_queue_command(struct Scsi_Host *h, struct scsi_cmnd *SCpnt) 342 * Purpose : queue a command for adapter to process. 343 * Params : h - host adapter 344 * : SCpnt - Command to queue 345 * Returns : 0 - success, else error 346 */ 347 extern int fas216_queue_command(struct Scsi_Host *h, struct scsi_cmnd *SCpnt); 348 349 /* Function: int fas216_noqueue_command(struct Scsi_Host *h, struct scsi_cmnd *SCpnt) 350 * Purpose : queue a command for adapter to process, and process it to completion. 351 * Params : h - host adapter 352 * : SCpnt - Command to queue 353 * Returns : 0 - success, else error 354 */ 355 extern int fas216_noqueue_command(struct Scsi_Host *, struct scsi_cmnd *); 356 357 /* Function: irqreturn_t fas216_intr (FAS216_Info *info) 358 * Purpose : handle interrupts from the interface to progress a command 359 * Params : info - interface to service 360 */ 361 extern irqreturn_t fas216_intr (FAS216_Info *info); 362 363 extern void fas216_remove (struct Scsi_Host *instance); 364 365 /* Function: void fas216_release (struct Scsi_Host *instance) 366 * Purpose : release all resources and put everything to bed for FAS/NCR/AMD SCSI ic. 367 * Params : instance - a driver-specific filled-out structure 368 * Returns : 0 on success 369 */ 370 extern void fas216_release (struct Scsi_Host *instance); 371 372 extern void fas216_print_host(FAS216_Info *info, struct seq_file *m); 373 extern void fas216_print_stats(FAS216_Info *info, struct seq_file *m); 374 extern void fas216_print_devices(FAS216_Info *info, struct seq_file *m); 375 376 /* Function: int fas216_eh_abort(struct scsi_cmnd *SCpnt) 377 * Purpose : abort this command 378 * Params : SCpnt - command to abort 379 * Returns : FAILED if unable to abort 380 */ 381 extern int fas216_eh_abort(struct scsi_cmnd *SCpnt); 382 383 /* Function: int fas216_eh_device_reset(struct scsi_cmnd *SCpnt) 384 * Purpose : Reset the device associated with this command 385 * Params : SCpnt - command specifing device to reset 386 * Returns : FAILED if unable to reset 387 */ 388 extern int fas216_eh_device_reset(struct scsi_cmnd *SCpnt); 389 390 /* Function: int fas216_eh_bus_reset(struct scsi_cmnd *SCpnt) 391 * Purpose : Reset the complete bus associated with this command 392 * Params : SCpnt - command specifing bus to reset 393 * Returns : FAILED if unable to reset 394 */ 395 extern int fas216_eh_bus_reset(struct scsi_cmnd *SCpnt); 396 397 /* Function: int fas216_eh_host_reset(struct scsi_cmnd *SCpnt) 398 * Purpose : Reset the host associated with this command 399 * Params : SCpnt - command specifing host to reset 400 * Returns : FAILED if unable to reset 401 */ 402 extern int fas216_eh_host_reset(struct scsi_cmnd *SCpnt); 403 404 #endif /* FAS216_H */ 405