1 /* 2 * Product specific probe and attach routines for: 3 * aic7901 and aic7902 SCSI controllers 4 * 5 * Copyright (c) 1994-2001 Justin T. Gibbs. 6 * Copyright (c) 2000-2002 Adaptec Inc. 7 * All rights reserved. 8 * 9 * Redistribution and use in source and binary forms, with or without 10 * modification, are permitted provided that the following conditions 11 * are met: 12 * 1. Redistributions of source code must retain the above copyright 13 * notice, this list of conditions, and the following disclaimer, 14 * without modification. 15 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 16 * substantially similar to the "NO WARRANTY" disclaimer below 17 * ("Disclaimer") and any redistribution must be conditioned upon 18 * including a substantially similar Disclaimer requirement for further 19 * binary redistribution. 20 * 3. Neither the names of the above-listed copyright holders nor the names 21 * of any contributors may be used to endorse or promote products derived 22 * from this software without specific prior written permission. 23 * 24 * Alternatively, this software may be distributed under the terms of the 25 * GNU General Public License ("GPL") version 2 as published by the Free 26 * Software Foundation. 27 * 28 * NO WARRANTY 29 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 30 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 31 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR 32 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 33 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 34 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 35 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 36 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 37 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING 38 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 39 * POSSIBILITY OF SUCH DAMAGES. 40 * 41 * $Id: //depot/aic7xxx/aic7xxx/aic79xx_pci.c#92 $ 42 */ 43 44 #ifdef __linux__ 45 #include "aic79xx_osm.h" 46 #include "aic79xx_inline.h" 47 #else 48 #include <dev/aic7xxx/aic79xx_osm.h> 49 #include <dev/aic7xxx/aic79xx_inline.h> 50 #endif 51 52 #include "aic79xx_pci.h" 53 54 static inline uint64_t 55 ahd_compose_id(u_int device, u_int vendor, u_int subdevice, u_int subvendor) 56 { 57 uint64_t id; 58 59 id = subvendor 60 | (subdevice << 16) 61 | ((uint64_t)vendor << 32) 62 | ((uint64_t)device << 48); 63 64 return (id); 65 } 66 67 #define ID_AIC7902_PCI_REV_A4 0x3 68 #define ID_AIC7902_PCI_REV_B0 0x10 69 #define SUBID_HP 0x0E11 70 71 #define DEVID_9005_HOSTRAID(id) ((id) & 0x80) 72 73 #define DEVID_9005_TYPE(id) ((id) & 0xF) 74 #define DEVID_9005_TYPE_HBA 0x0 /* Standard Card */ 75 #define DEVID_9005_TYPE_HBA_2EXT 0x1 /* 2 External Ports */ 76 #define DEVID_9005_TYPE_IROC 0x8 /* Raid(0,1,10) Card */ 77 #define DEVID_9005_TYPE_MB 0xF /* On Motherboard */ 78 79 #define DEVID_9005_MFUNC(id) ((id) & 0x10) 80 81 #define DEVID_9005_PACKETIZED(id) ((id) & 0x8000) 82 83 #define SUBID_9005_TYPE(id) ((id) & 0xF) 84 #define SUBID_9005_TYPE_HBA 0x0 /* Standard Card */ 85 #define SUBID_9005_TYPE_MB 0xF /* On Motherboard */ 86 87 #define SUBID_9005_AUTOTERM(id) (((id) & 0x10) == 0) 88 89 #define SUBID_9005_LEGACYCONN_FUNC(id) ((id) & 0x20) 90 91 #define SUBID_9005_SEEPTYPE(id) (((id) & 0x0C0) >> 6) 92 #define SUBID_9005_SEEPTYPE_NONE 0x0 93 #define SUBID_9005_SEEPTYPE_4K 0x1 94 95 static ahd_device_setup_t ahd_aic7901_setup; 96 static ahd_device_setup_t ahd_aic7901A_setup; 97 static ahd_device_setup_t ahd_aic7902_setup; 98 static ahd_device_setup_t ahd_aic790X_setup; 99 100 static const struct ahd_pci_identity ahd_pci_ident_table[] = 101 { 102 /* aic7901 based controllers */ 103 { 104 ID_AHA_29320A, 105 ID_ALL_MASK, 106 "Adaptec 29320A Ultra320 SCSI adapter", 107 ahd_aic7901_setup 108 }, 109 { 110 ID_AHA_29320ALP, 111 ID_ALL_MASK, 112 "Adaptec 29320ALP PCIx Ultra320 SCSI adapter", 113 ahd_aic7901_setup 114 }, 115 { 116 ID_AHA_29320LPE, 117 ID_ALL_MASK, 118 "Adaptec 29320LPE PCIe Ultra320 SCSI adapter", 119 ahd_aic7901_setup 120 }, 121 /* aic7901A based controllers */ 122 { 123 ID_AHA_29320LP, 124 ID_ALL_MASK, 125 "Adaptec 29320LP Ultra320 SCSI adapter", 126 ahd_aic7901A_setup 127 }, 128 /* aic7902 based controllers */ 129 { 130 ID_AHA_29320, 131 ID_ALL_MASK, 132 "Adaptec 29320 Ultra320 SCSI adapter", 133 ahd_aic7902_setup 134 }, 135 { 136 ID_AHA_29320B, 137 ID_ALL_MASK, 138 "Adaptec 29320B Ultra320 SCSI adapter", 139 ahd_aic7902_setup 140 }, 141 { 142 ID_AHA_39320, 143 ID_ALL_MASK, 144 "Adaptec 39320 Ultra320 SCSI adapter", 145 ahd_aic7902_setup 146 }, 147 { 148 ID_AHA_39320_B, 149 ID_ALL_MASK, 150 "Adaptec 39320 Ultra320 SCSI adapter", 151 ahd_aic7902_setup 152 }, 153 { 154 ID_AHA_39320_B_DELL, 155 ID_ALL_MASK, 156 "Adaptec (Dell OEM) 39320 Ultra320 SCSI adapter", 157 ahd_aic7902_setup 158 }, 159 { 160 ID_AHA_39320A, 161 ID_ALL_MASK, 162 "Adaptec 39320A Ultra320 SCSI adapter", 163 ahd_aic7902_setup 164 }, 165 { 166 ID_AHA_39320D, 167 ID_ALL_MASK, 168 "Adaptec 39320D Ultra320 SCSI adapter", 169 ahd_aic7902_setup 170 }, 171 { 172 ID_AHA_39320D_HP, 173 ID_ALL_MASK, 174 "Adaptec (HP OEM) 39320D Ultra320 SCSI adapter", 175 ahd_aic7902_setup 176 }, 177 { 178 ID_AHA_39320D_B, 179 ID_ALL_MASK, 180 "Adaptec 39320D Ultra320 SCSI adapter", 181 ahd_aic7902_setup 182 }, 183 { 184 ID_AHA_39320D_B_HP, 185 ID_ALL_MASK, 186 "Adaptec (HP OEM) 39320D Ultra320 SCSI adapter", 187 ahd_aic7902_setup 188 }, 189 /* Generic chip probes for devices we don't know 'exactly' */ 190 { 191 ID_AIC7901 & ID_9005_GENERIC_MASK, 192 ID_9005_GENERIC_MASK, 193 "Adaptec AIC7901 Ultra320 SCSI adapter", 194 ahd_aic7901_setup 195 }, 196 { 197 ID_AIC7901A & ID_DEV_VENDOR_MASK, 198 ID_DEV_VENDOR_MASK, 199 "Adaptec AIC7901A Ultra320 SCSI adapter", 200 ahd_aic7901A_setup 201 }, 202 { 203 ID_AIC7902 & ID_9005_GENERIC_MASK, 204 ID_9005_GENERIC_MASK, 205 "Adaptec AIC7902 Ultra320 SCSI adapter", 206 ahd_aic7902_setup 207 } 208 }; 209 210 static const u_int ahd_num_pci_devs = ARRAY_SIZE(ahd_pci_ident_table); 211 212 #define DEVCONFIG 0x40 213 #define PCIXINITPAT 0x0000E000ul 214 #define PCIXINIT_PCI33_66 0x0000E000ul 215 #define PCIXINIT_PCIX50_66 0x0000C000ul 216 #define PCIXINIT_PCIX66_100 0x0000A000ul 217 #define PCIXINIT_PCIX100_133 0x00008000ul 218 #define PCI_BUS_MODES_INDEX(devconfig) \ 219 (((devconfig) & PCIXINITPAT) >> 13) 220 static const char *pci_bus_modes[] = 221 { 222 "PCI bus mode unknown", 223 "PCI bus mode unknown", 224 "PCI bus mode unknown", 225 "PCI bus mode unknown", 226 "PCI-X 101-133MHz", 227 "PCI-X 67-100MHz", 228 "PCI-X 50-66MHz", 229 "PCI 33 or 66MHz" 230 }; 231 232 #define TESTMODE 0x00000800ul 233 #define IRDY_RST 0x00000200ul 234 #define FRAME_RST 0x00000100ul 235 #define PCI64BIT 0x00000080ul 236 #define MRDCEN 0x00000040ul 237 #define ENDIANSEL 0x00000020ul 238 #define MIXQWENDIANEN 0x00000008ul 239 #define DACEN 0x00000004ul 240 #define STPWLEVEL 0x00000002ul 241 #define QWENDIANSEL 0x00000001ul 242 243 #define DEVCONFIG1 0x44 244 #define PREQDIS 0x01 245 246 #define CSIZE_LATTIME 0x0c 247 #define CACHESIZE 0x000000fful 248 #define LATTIME 0x0000ff00ul 249 250 static int ahd_check_extport(struct ahd_softc *ahd); 251 static void ahd_configure_termination(struct ahd_softc *ahd, 252 u_int adapter_control); 253 static void ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat); 254 static void ahd_pci_intr(struct ahd_softc *ahd); 255 256 const struct ahd_pci_identity * 257 ahd_find_pci_device(ahd_dev_softc_t pci) 258 { 259 uint64_t full_id; 260 uint16_t device; 261 uint16_t vendor; 262 uint16_t subdevice; 263 uint16_t subvendor; 264 const struct ahd_pci_identity *entry; 265 u_int i; 266 267 vendor = ahd_pci_read_config(pci, PCIR_DEVVENDOR, /*bytes*/2); 268 device = ahd_pci_read_config(pci, PCIR_DEVICE, /*bytes*/2); 269 subvendor = ahd_pci_read_config(pci, PCIR_SUBVEND_0, /*bytes*/2); 270 subdevice = ahd_pci_read_config(pci, PCIR_SUBDEV_0, /*bytes*/2); 271 full_id = ahd_compose_id(device, 272 vendor, 273 subdevice, 274 subvendor); 275 276 /* 277 * Controllers, mask out the IROC/HostRAID bit 278 */ 279 280 full_id &= ID_ALL_IROC_MASK; 281 282 for (i = 0; i < ahd_num_pci_devs; i++) { 283 entry = &ahd_pci_ident_table[i]; 284 if (entry->full_id == (full_id & entry->id_mask)) { 285 /* Honor exclusion entries. */ 286 if (entry->name == NULL) 287 return (NULL); 288 return (entry); 289 } 290 } 291 return (NULL); 292 } 293 294 int 295 ahd_pci_config(struct ahd_softc *ahd, const struct ahd_pci_identity *entry) 296 { 297 struct scb_data *shared_scb_data; 298 u_int command; 299 uint32_t devconfig; 300 uint16_t subvendor; 301 int error; 302 303 shared_scb_data = NULL; 304 ahd->description = entry->name; 305 /* 306 * Record if this is an HP board. 307 */ 308 subvendor = ahd_pci_read_config(ahd->dev_softc, 309 PCIR_SUBVEND_0, /*bytes*/2); 310 if (subvendor == SUBID_HP) 311 ahd->flags |= AHD_HP_BOARD; 312 313 error = entry->setup(ahd); 314 if (error != 0) 315 return (error); 316 317 devconfig = ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4); 318 if ((devconfig & PCIXINITPAT) == PCIXINIT_PCI33_66) { 319 ahd->chip |= AHD_PCI; 320 /* Disable PCIX workarounds when running in PCI mode. */ 321 ahd->bugs &= ~AHD_PCIX_BUG_MASK; 322 } else { 323 ahd->chip |= AHD_PCIX; 324 } 325 ahd->bus_description = pci_bus_modes[PCI_BUS_MODES_INDEX(devconfig)]; 326 327 ahd_power_state_change(ahd, AHD_POWER_STATE_D0); 328 329 error = ahd_pci_map_registers(ahd); 330 if (error != 0) 331 return (error); 332 333 /* 334 * If we need to support high memory, enable dual 335 * address cycles. This bit must be set to enable 336 * high address bit generation even if we are on a 337 * 64bit bus (PCI64BIT set in devconfig). 338 */ 339 if ((ahd->flags & (AHD_39BIT_ADDRESSING|AHD_64BIT_ADDRESSING)) != 0) { 340 if (bootverbose) 341 printk("%s: Enabling 39Bit Addressing\n", 342 ahd_name(ahd)); 343 devconfig = ahd_pci_read_config(ahd->dev_softc, 344 DEVCONFIG, /*bytes*/4); 345 devconfig |= DACEN; 346 ahd_pci_write_config(ahd->dev_softc, DEVCONFIG, 347 devconfig, /*bytes*/4); 348 } 349 350 /* Ensure busmastering is enabled */ 351 command = ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2); 352 command |= PCIM_CMD_BUSMASTEREN; 353 ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, command, /*bytes*/2); 354 355 error = ahd_softc_init(ahd); 356 if (error != 0) 357 return (error); 358 359 ahd->bus_intr = ahd_pci_intr; 360 361 error = ahd_reset(ahd, /*reinit*/FALSE); 362 if (error != 0) 363 return (ENXIO); 364 365 ahd->pci_cachesize = 366 ahd_pci_read_config(ahd->dev_softc, CSIZE_LATTIME, 367 /*bytes*/1) & CACHESIZE; 368 ahd->pci_cachesize *= 4; 369 370 ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); 371 /* See if we have a SEEPROM and perform auto-term */ 372 error = ahd_check_extport(ahd); 373 if (error != 0) 374 return (error); 375 376 /* Core initialization */ 377 error = ahd_init(ahd); 378 if (error != 0) 379 return (error); 380 ahd->init_level++; 381 382 /* 383 * Allow interrupts now that we are completely setup. 384 */ 385 return ahd_pci_map_int(ahd); 386 } 387 388 #ifdef CONFIG_PM 389 void 390 ahd_pci_suspend(struct ahd_softc *ahd) 391 { 392 /* 393 * Save chip register configuration data for chip resets 394 * that occur during runtime and resume events. 395 */ 396 ahd->suspend_state.pci_state.devconfig = 397 ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4); 398 ahd->suspend_state.pci_state.command = 399 ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/1); 400 ahd->suspend_state.pci_state.csize_lattime = 401 ahd_pci_read_config(ahd->dev_softc, CSIZE_LATTIME, /*bytes*/1); 402 403 } 404 405 void 406 ahd_pci_resume(struct ahd_softc *ahd) 407 { 408 ahd_pci_write_config(ahd->dev_softc, DEVCONFIG, 409 ahd->suspend_state.pci_state.devconfig, /*bytes*/4); 410 ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, 411 ahd->suspend_state.pci_state.command, /*bytes*/1); 412 ahd_pci_write_config(ahd->dev_softc, CSIZE_LATTIME, 413 ahd->suspend_state.pci_state.csize_lattime, /*bytes*/1); 414 } 415 #endif 416 417 /* 418 * Perform some simple tests that should catch situations where 419 * our registers are invalidly mapped. 420 */ 421 int 422 ahd_pci_test_register_access(struct ahd_softc *ahd) 423 { 424 uint32_t cmd; 425 u_int targpcistat; 426 u_int pci_status1; 427 int error; 428 uint8_t hcntrl; 429 430 error = EIO; 431 432 /* 433 * Enable PCI error interrupt status, but suppress NMIs 434 * generated by SERR raised due to target aborts. 435 */ 436 cmd = ahd_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2); 437 ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, 438 cmd & ~PCIM_CMD_SERRESPEN, /*bytes*/2); 439 440 /* 441 * First a simple test to see if any 442 * registers can be read. Reading 443 * HCNTRL has no side effects and has 444 * at least one bit that is guaranteed to 445 * be zero so it is a good register to 446 * use for this test. 447 */ 448 hcntrl = ahd_inb(ahd, HCNTRL); 449 if (hcntrl == 0xFF) 450 goto fail; 451 452 /* 453 * Next create a situation where write combining 454 * or read prefetching could be initiated by the 455 * CPU or host bridge. Our device does not support 456 * either, so look for data corruption and/or flaged 457 * PCI errors. First pause without causing another 458 * chip reset. 459 */ 460 hcntrl &= ~CHIPRST; 461 ahd_outb(ahd, HCNTRL, hcntrl|PAUSE); 462 while (ahd_is_paused(ahd) == 0) 463 ; 464 465 /* Clear any PCI errors that occurred before our driver attached. */ 466 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 467 targpcistat = ahd_inb(ahd, TARGPCISTAT); 468 ahd_outb(ahd, TARGPCISTAT, targpcistat); 469 pci_status1 = ahd_pci_read_config(ahd->dev_softc, 470 PCIR_STATUS + 1, /*bytes*/1); 471 ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, 472 pci_status1, /*bytes*/1); 473 ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); 474 ahd_outb(ahd, CLRINT, CLRPCIINT); 475 476 ahd_outb(ahd, SEQCTL0, PERRORDIS); 477 ahd_outl(ahd, SRAM_BASE, 0x5aa555aa); 478 if (ahd_inl(ahd, SRAM_BASE) != 0x5aa555aa) 479 goto fail; 480 481 if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) { 482 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 483 targpcistat = ahd_inb(ahd, TARGPCISTAT); 484 if ((targpcistat & STA) != 0) 485 goto fail; 486 } 487 488 error = 0; 489 490 fail: 491 if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) { 492 493 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 494 targpcistat = ahd_inb(ahd, TARGPCISTAT); 495 496 /* Silently clear any latched errors. */ 497 ahd_outb(ahd, TARGPCISTAT, targpcistat); 498 pci_status1 = ahd_pci_read_config(ahd->dev_softc, 499 PCIR_STATUS + 1, /*bytes*/1); 500 ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, 501 pci_status1, /*bytes*/1); 502 ahd_outb(ahd, CLRINT, CLRPCIINT); 503 } 504 ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS); 505 ahd_pci_write_config(ahd->dev_softc, PCIR_COMMAND, cmd, /*bytes*/2); 506 return (error); 507 } 508 509 /* 510 * Check the external port logic for a serial eeprom 511 * and termination/cable detection contrls. 512 */ 513 static int 514 ahd_check_extport(struct ahd_softc *ahd) 515 { 516 struct vpd_config vpd; 517 struct seeprom_config *sc; 518 u_int adapter_control; 519 int have_seeprom; 520 int error; 521 522 sc = ahd->seep_config; 523 have_seeprom = ahd_acquire_seeprom(ahd); 524 if (have_seeprom) { 525 u_int start_addr; 526 527 /* 528 * Fetch VPD for this function and parse it. 529 */ 530 if (bootverbose) 531 printk("%s: Reading VPD from SEEPROM...", 532 ahd_name(ahd)); 533 534 /* Address is always in units of 16bit words */ 535 start_addr = ((2 * sizeof(*sc)) 536 + (sizeof(vpd) * (ahd->channel - 'A'))) / 2; 537 538 error = ahd_read_seeprom(ahd, (uint16_t *)&vpd, 539 start_addr, sizeof(vpd)/2, 540 /*bytestream*/TRUE); 541 if (error == 0) 542 error = ahd_parse_vpddata(ahd, &vpd); 543 if (bootverbose) 544 printk("%s: VPD parsing %s\n", 545 ahd_name(ahd), 546 error == 0 ? "successful" : "failed"); 547 548 if (bootverbose) 549 printk("%s: Reading SEEPROM...", ahd_name(ahd)); 550 551 /* Address is always in units of 16bit words */ 552 start_addr = (sizeof(*sc) / 2) * (ahd->channel - 'A'); 553 554 error = ahd_read_seeprom(ahd, (uint16_t *)sc, 555 start_addr, sizeof(*sc)/2, 556 /*bytestream*/FALSE); 557 558 if (error != 0) { 559 printk("Unable to read SEEPROM\n"); 560 have_seeprom = 0; 561 } else { 562 have_seeprom = ahd_verify_cksum(sc); 563 564 if (bootverbose) { 565 if (have_seeprom == 0) 566 printk ("checksum error\n"); 567 else 568 printk ("done.\n"); 569 } 570 } 571 ahd_release_seeprom(ahd); 572 } 573 574 if (!have_seeprom) { 575 u_int nvram_scb; 576 577 /* 578 * Pull scratch ram settings and treat them as 579 * if they are the contents of an seeprom if 580 * the 'ADPT', 'BIOS', or 'ASPI' signature is found 581 * in SCB 0xFF. We manually compose the data as 16bit 582 * values to avoid endian issues. 583 */ 584 ahd_set_scbptr(ahd, 0xFF); 585 nvram_scb = ahd_inb_scbram(ahd, SCB_BASE + NVRAM_SCB_OFFSET); 586 if (nvram_scb != 0xFF 587 && ((ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A' 588 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'D' 589 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P' 590 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'T') 591 || (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'B' 592 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'I' 593 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'O' 594 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'S') 595 || (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A' 596 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'S' 597 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P' 598 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'I'))) { 599 uint16_t *sc_data; 600 int i; 601 602 ahd_set_scbptr(ahd, nvram_scb); 603 sc_data = (uint16_t *)sc; 604 for (i = 0; i < 64; i += 2) 605 *sc_data++ = ahd_inw_scbram(ahd, SCB_BASE+i); 606 have_seeprom = ahd_verify_cksum(sc); 607 if (have_seeprom) 608 ahd->flags |= AHD_SCB_CONFIG_USED; 609 } 610 } 611 612 #ifdef AHD_DEBUG 613 if (have_seeprom != 0 614 && (ahd_debug & AHD_DUMP_SEEPROM) != 0) { 615 uint16_t *sc_data; 616 int i; 617 618 printk("%s: Seeprom Contents:", ahd_name(ahd)); 619 sc_data = (uint16_t *)sc; 620 for (i = 0; i < (sizeof(*sc)); i += 2) 621 printk("\n\t0x%.4x", sc_data[i]); 622 printk("\n"); 623 } 624 #endif 625 626 if (!have_seeprom) { 627 if (bootverbose) 628 printk("%s: No SEEPROM available.\n", ahd_name(ahd)); 629 ahd->flags |= AHD_USEDEFAULTS; 630 error = ahd_default_config(ahd); 631 adapter_control = CFAUTOTERM|CFSEAUTOTERM; 632 kfree(ahd->seep_config); 633 ahd->seep_config = NULL; 634 } else { 635 error = ahd_parse_cfgdata(ahd, sc); 636 adapter_control = sc->adapter_control; 637 } 638 if (error != 0) 639 return (error); 640 641 ahd_configure_termination(ahd, adapter_control); 642 643 return (0); 644 } 645 646 static void 647 ahd_configure_termination(struct ahd_softc *ahd, u_int adapter_control) 648 { 649 int error; 650 u_int sxfrctl1; 651 uint8_t termctl; 652 uint32_t devconfig; 653 654 devconfig = ahd_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4); 655 devconfig &= ~STPWLEVEL; 656 if ((ahd->flags & AHD_STPWLEVEL_A) != 0) 657 devconfig |= STPWLEVEL; 658 if (bootverbose) 659 printk("%s: STPWLEVEL is %s\n", 660 ahd_name(ahd), (devconfig & STPWLEVEL) ? "on" : "off"); 661 ahd_pci_write_config(ahd->dev_softc, DEVCONFIG, devconfig, /*bytes*/4); 662 663 /* Make sure current sensing is off. */ 664 if ((ahd->flags & AHD_CURRENT_SENSING) != 0) { 665 (void)ahd_write_flexport(ahd, FLXADDR_ROMSTAT_CURSENSECTL, 0); 666 } 667 668 /* 669 * Read to sense. Write to set. 670 */ 671 error = ahd_read_flexport(ahd, FLXADDR_TERMCTL, &termctl); 672 if ((adapter_control & CFAUTOTERM) == 0) { 673 if (bootverbose) 674 printk("%s: Manual Primary Termination\n", 675 ahd_name(ahd)); 676 termctl &= ~(FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH); 677 if ((adapter_control & CFSTERM) != 0) 678 termctl |= FLX_TERMCTL_ENPRILOW; 679 if ((adapter_control & CFWSTERM) != 0) 680 termctl |= FLX_TERMCTL_ENPRIHIGH; 681 } else if (error != 0) { 682 printk("%s: Primary Auto-Term Sensing failed! " 683 "Using Defaults.\n", ahd_name(ahd)); 684 termctl = FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH; 685 } 686 687 if ((adapter_control & CFSEAUTOTERM) == 0) { 688 if (bootverbose) 689 printk("%s: Manual Secondary Termination\n", 690 ahd_name(ahd)); 691 termctl &= ~(FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH); 692 if ((adapter_control & CFSELOWTERM) != 0) 693 termctl |= FLX_TERMCTL_ENSECLOW; 694 if ((adapter_control & CFSEHIGHTERM) != 0) 695 termctl |= FLX_TERMCTL_ENSECHIGH; 696 } else if (error != 0) { 697 printk("%s: Secondary Auto-Term Sensing failed! " 698 "Using Defaults.\n", ahd_name(ahd)); 699 termctl |= FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH; 700 } 701 702 /* 703 * Now set the termination based on what we found. 704 */ 705 sxfrctl1 = ahd_inb(ahd, SXFRCTL1) & ~STPWEN; 706 ahd->flags &= ~AHD_TERM_ENB_A; 707 if ((termctl & FLX_TERMCTL_ENPRILOW) != 0) { 708 ahd->flags |= AHD_TERM_ENB_A; 709 sxfrctl1 |= STPWEN; 710 } 711 /* Must set the latch once in order to be effective. */ 712 ahd_outb(ahd, SXFRCTL1, sxfrctl1|STPWEN); 713 ahd_outb(ahd, SXFRCTL1, sxfrctl1); 714 715 error = ahd_write_flexport(ahd, FLXADDR_TERMCTL, termctl); 716 if (error != 0) { 717 printk("%s: Unable to set termination settings!\n", 718 ahd_name(ahd)); 719 } else if (bootverbose) { 720 printk("%s: Primary High byte termination %sabled\n", 721 ahd_name(ahd), 722 (termctl & FLX_TERMCTL_ENPRIHIGH) ? "En" : "Dis"); 723 724 printk("%s: Primary Low byte termination %sabled\n", 725 ahd_name(ahd), 726 (termctl & FLX_TERMCTL_ENPRILOW) ? "En" : "Dis"); 727 728 printk("%s: Secondary High byte termination %sabled\n", 729 ahd_name(ahd), 730 (termctl & FLX_TERMCTL_ENSECHIGH) ? "En" : "Dis"); 731 732 printk("%s: Secondary Low byte termination %sabled\n", 733 ahd_name(ahd), 734 (termctl & FLX_TERMCTL_ENSECLOW) ? "En" : "Dis"); 735 } 736 return; 737 } 738 739 #define DPE 0x80 740 #define SSE 0x40 741 #define RMA 0x20 742 #define RTA 0x10 743 #define STA 0x08 744 #define DPR 0x01 745 746 static const char *split_status_source[] = 747 { 748 "DFF0", 749 "DFF1", 750 "OVLY", 751 "CMC", 752 }; 753 754 static const char *pci_status_source[] = 755 { 756 "DFF0", 757 "DFF1", 758 "SG", 759 "CMC", 760 "OVLY", 761 "NONE", 762 "MSI", 763 "TARG" 764 }; 765 766 static const char *split_status_strings[] = 767 { 768 "%s: Received split response in %s.\n", 769 "%s: Received split completion error message in %s\n", 770 "%s: Receive overrun in %s\n", 771 "%s: Count not complete in %s\n", 772 "%s: Split completion data bucket in %s\n", 773 "%s: Split completion address error in %s\n", 774 "%s: Split completion byte count error in %s\n", 775 "%s: Signaled Target-abort to early terminate a split in %s\n" 776 }; 777 778 static const char *pci_status_strings[] = 779 { 780 "%s: Data Parity Error has been reported via PERR# in %s\n", 781 "%s: Target initial wait state error in %s\n", 782 "%s: Split completion read data parity error in %s\n", 783 "%s: Split completion address attribute parity error in %s\n", 784 "%s: Received a Target Abort in %s\n", 785 "%s: Received a Master Abort in %s\n", 786 "%s: Signal System Error Detected in %s\n", 787 "%s: Address or Write Phase Parity Error Detected in %s.\n" 788 }; 789 790 static void 791 ahd_pci_intr(struct ahd_softc *ahd) 792 { 793 uint8_t pci_status[8]; 794 ahd_mode_state saved_modes; 795 u_int pci_status1; 796 u_int intstat; 797 u_int i; 798 u_int reg; 799 800 intstat = ahd_inb(ahd, INTSTAT); 801 802 if ((intstat & SPLTINT) != 0) 803 ahd_pci_split_intr(ahd, intstat); 804 805 if ((intstat & PCIINT) == 0) 806 return; 807 808 printk("%s: PCI error Interrupt\n", ahd_name(ahd)); 809 saved_modes = ahd_save_modes(ahd); 810 ahd_dump_card_state(ahd); 811 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 812 for (i = 0, reg = DF0PCISTAT; i < 8; i++, reg++) { 813 814 if (i == 5) 815 continue; 816 pci_status[i] = ahd_inb(ahd, reg); 817 /* Clear latched errors. So our interrupt deasserts. */ 818 ahd_outb(ahd, reg, pci_status[i]); 819 } 820 821 for (i = 0; i < 8; i++) { 822 u_int bit; 823 824 if (i == 5) 825 continue; 826 827 for (bit = 0; bit < 8; bit++) { 828 829 if ((pci_status[i] & (0x1 << bit)) != 0) { 830 const char *s; 831 832 s = pci_status_strings[bit]; 833 if (i == 7/*TARG*/ && bit == 3) 834 s = "%s: Signaled Target Abort\n"; 835 printk(s, ahd_name(ahd), pci_status_source[i]); 836 } 837 } 838 } 839 pci_status1 = ahd_pci_read_config(ahd->dev_softc, 840 PCIR_STATUS + 1, /*bytes*/1); 841 ahd_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, 842 pci_status1, /*bytes*/1); 843 ahd_restore_modes(ahd, saved_modes); 844 ahd_outb(ahd, CLRINT, CLRPCIINT); 845 ahd_unpause(ahd); 846 } 847 848 static void 849 ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat) 850 { 851 uint8_t split_status[4]; 852 uint8_t split_status1[4]; 853 uint8_t sg_split_status[2]; 854 uint8_t sg_split_status1[2]; 855 ahd_mode_state saved_modes; 856 u_int i; 857 uint16_t pcix_status; 858 859 /* 860 * Check for splits in all modes. Modes 0 and 1 861 * additionally have SG engine splits to look at. 862 */ 863 pcix_status = ahd_pci_read_config(ahd->dev_softc, PCIXR_STATUS, 864 /*bytes*/2); 865 printk("%s: PCI Split Interrupt - PCI-X status = 0x%x\n", 866 ahd_name(ahd), pcix_status); 867 saved_modes = ahd_save_modes(ahd); 868 for (i = 0; i < 4; i++) { 869 ahd_set_modes(ahd, i, i); 870 871 split_status[i] = ahd_inb(ahd, DCHSPLTSTAT0); 872 split_status1[i] = ahd_inb(ahd, DCHSPLTSTAT1); 873 /* Clear latched errors. So our interrupt deasserts. */ 874 ahd_outb(ahd, DCHSPLTSTAT0, split_status[i]); 875 ahd_outb(ahd, DCHSPLTSTAT1, split_status1[i]); 876 if (i > 1) 877 continue; 878 sg_split_status[i] = ahd_inb(ahd, SGSPLTSTAT0); 879 sg_split_status1[i] = ahd_inb(ahd, SGSPLTSTAT1); 880 /* Clear latched errors. So our interrupt deasserts. */ 881 ahd_outb(ahd, SGSPLTSTAT0, sg_split_status[i]); 882 ahd_outb(ahd, SGSPLTSTAT1, sg_split_status1[i]); 883 } 884 885 for (i = 0; i < 4; i++) { 886 u_int bit; 887 888 for (bit = 0; bit < 8; bit++) { 889 890 if ((split_status[i] & (0x1 << bit)) != 0) 891 printk(split_status_strings[bit], ahd_name(ahd), 892 split_status_source[i]); 893 894 if (i > 1) 895 continue; 896 897 if ((sg_split_status[i] & (0x1 << bit)) != 0) 898 printk(split_status_strings[bit], ahd_name(ahd), "SG"); 899 } 900 } 901 /* 902 * Clear PCI-X status bits. 903 */ 904 ahd_pci_write_config(ahd->dev_softc, PCIXR_STATUS, 905 pcix_status, /*bytes*/2); 906 ahd_outb(ahd, CLRINT, CLRSPLTINT); 907 ahd_restore_modes(ahd, saved_modes); 908 } 909 910 static int 911 ahd_aic7901_setup(struct ahd_softc *ahd) 912 { 913 914 ahd->chip = AHD_AIC7901; 915 ahd->features = AHD_AIC7901_FE; 916 return (ahd_aic790X_setup(ahd)); 917 } 918 919 static int 920 ahd_aic7901A_setup(struct ahd_softc *ahd) 921 { 922 923 ahd->chip = AHD_AIC7901A; 924 ahd->features = AHD_AIC7901A_FE; 925 return (ahd_aic790X_setup(ahd)); 926 } 927 928 static int 929 ahd_aic7902_setup(struct ahd_softc *ahd) 930 { 931 ahd->chip = AHD_AIC7902; 932 ahd->features = AHD_AIC7902_FE; 933 return (ahd_aic790X_setup(ahd)); 934 } 935 936 static int 937 ahd_aic790X_setup(struct ahd_softc *ahd) 938 { 939 ahd_dev_softc_t pci; 940 u_int rev; 941 942 pci = ahd->dev_softc; 943 rev = ahd_pci_read_config(pci, PCIR_REVID, /*bytes*/1); 944 if (rev < ID_AIC7902_PCI_REV_A4) { 945 printk("%s: Unable to attach to unsupported chip revision %d\n", 946 ahd_name(ahd), rev); 947 ahd_pci_write_config(pci, PCIR_COMMAND, 0, /*bytes*/2); 948 return (ENXIO); 949 } 950 ahd->channel = ahd_get_pci_function(pci) + 'A'; 951 if (rev < ID_AIC7902_PCI_REV_B0) { 952 /* 953 * Enable A series workarounds. 954 */ 955 ahd->bugs |= AHD_SENT_SCB_UPDATE_BUG|AHD_ABORT_LQI_BUG 956 | AHD_PKT_BITBUCKET_BUG|AHD_LONG_SETIMO_BUG 957 | AHD_NLQICRC_DELAYED_BUG|AHD_SCSIRST_BUG 958 | AHD_LQO_ATNO_BUG|AHD_AUTOFLUSH_BUG 959 | AHD_CLRLQO_AUTOCLR_BUG|AHD_PCIX_MMAPIO_BUG 960 | AHD_PCIX_CHIPRST_BUG|AHD_PCIX_SCBRAM_RD_BUG 961 | AHD_PKTIZED_STATUS_BUG|AHD_PKT_LUN_BUG 962 | AHD_MDFF_WSCBPTR_BUG|AHD_REG_SLOW_SETTLE_BUG 963 | AHD_SET_MODE_BUG|AHD_BUSFREEREV_BUG 964 | AHD_NONPACKFIFO_BUG|AHD_PACED_NEGTABLE_BUG 965 | AHD_FAINT_LED_BUG; 966 967 /* 968 * IO Cell parameter setup. 969 */ 970 AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29); 971 972 if ((ahd->flags & AHD_HP_BOARD) == 0) 973 AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVA); 974 } else { 975 /* This is revision B and newer. */ 976 extern uint32_t aic79xx_slowcrc; 977 u_int devconfig1; 978 979 ahd->features |= AHD_RTI|AHD_NEW_IOCELL_OPTS 980 | AHD_NEW_DFCNTRL_OPTS|AHD_FAST_CDB_DELIVERY 981 | AHD_BUSFREEREV_BUG; 982 ahd->bugs |= AHD_LQOOVERRUN_BUG|AHD_EARLY_REQ_BUG; 983 984 /* If the user requested that the SLOWCRC bit to be set. */ 985 if (aic79xx_slowcrc) 986 ahd->features |= AHD_AIC79XXB_SLOWCRC; 987 988 /* 989 * Some issues have been resolved in the 7901B. 990 */ 991 if ((ahd->features & AHD_MULTI_FUNC) != 0) 992 ahd->bugs |= AHD_INTCOLLISION_BUG|AHD_ABORT_LQI_BUG; 993 994 /* 995 * IO Cell parameter setup. 996 */ 997 AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29); 998 AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVB); 999 AHD_SET_AMPLITUDE(ahd, AHD_AMPLITUDE_DEF); 1000 1001 /* 1002 * Set the PREQDIS bit for H2B which disables some workaround 1003 * that doesn't work on regular PCI busses. 1004 * XXX - Find out exactly what this does from the hardware 1005 * folks! 1006 */ 1007 devconfig1 = ahd_pci_read_config(pci, DEVCONFIG1, /*bytes*/1); 1008 ahd_pci_write_config(pci, DEVCONFIG1, 1009 devconfig1|PREQDIS, /*bytes*/1); 1010 devconfig1 = ahd_pci_read_config(pci, DEVCONFIG1, /*bytes*/1); 1011 } 1012 1013 return (0); 1014 } 1015