1 /* 2 * advansys.c - Linux Host Driver for AdvanSys SCSI Adapters 3 * 4 * Copyright (c) 1995-2000 Advanced System Products, Inc. 5 * Copyright (c) 2000-2001 ConnectCom Solutions, Inc. 6 * Copyright (c) 2007 Matthew Wilcox <matthew@wil.cx> 7 * Copyright (c) 2014 Hannes Reinecke <hare@suse.de> 8 * All Rights Reserved. 9 * 10 * This program is free software; you can redistribute it and/or modify 11 * it under the terms of the GNU General Public License as published by 12 * the Free Software Foundation; either version 2 of the License, or 13 * (at your option) any later version. 14 */ 15 16 /* 17 * As of March 8, 2000 Advanced System Products, Inc. (AdvanSys) 18 * changed its name to ConnectCom Solutions, Inc. 19 * On June 18, 2001 Initio Corp. acquired ConnectCom's SCSI assets 20 */ 21 22 #include <linux/module.h> 23 #include <linux/string.h> 24 #include <linux/kernel.h> 25 #include <linux/types.h> 26 #include <linux/ioport.h> 27 #include <linux/interrupt.h> 28 #include <linux/delay.h> 29 #include <linux/slab.h> 30 #include <linux/mm.h> 31 #include <linux/proc_fs.h> 32 #include <linux/init.h> 33 #include <linux/blkdev.h> 34 #include <linux/isa.h> 35 #include <linux/eisa.h> 36 #include <linux/pci.h> 37 #include <linux/spinlock.h> 38 #include <linux/dma-mapping.h> 39 #include <linux/firmware.h> 40 #include <linux/dmapool.h> 41 42 #include <asm/io.h> 43 #include <asm/dma.h> 44 45 #include <scsi/scsi_cmnd.h> 46 #include <scsi/scsi_device.h> 47 #include <scsi/scsi_tcq.h> 48 #include <scsi/scsi.h> 49 #include <scsi/scsi_host.h> 50 51 #define DRV_NAME "advansys" 52 #define ASC_VERSION "3.5" /* AdvanSys Driver Version */ 53 54 /* FIXME: 55 * 56 * 1. Use scsi_transport_spi 57 * 2. advansys_info is not safe against multiple simultaneous callers 58 * 3. Add module_param to override ISA/VLB ioport array 59 */ 60 61 /* Enable driver /proc statistics. */ 62 #define ADVANSYS_STATS 63 64 /* Enable driver tracing. */ 65 #undef ADVANSYS_DEBUG 66 67 typedef unsigned char uchar; 68 69 #define isodd_word(val) ((((uint)val) & (uint)0x0001) != 0) 70 71 #define PCI_VENDOR_ID_ASP 0x10cd 72 #define PCI_DEVICE_ID_ASP_1200A 0x1100 73 #define PCI_DEVICE_ID_ASP_ABP940 0x1200 74 #define PCI_DEVICE_ID_ASP_ABP940U 0x1300 75 #define PCI_DEVICE_ID_ASP_ABP940UW 0x2300 76 #define PCI_DEVICE_ID_38C0800_REV1 0x2500 77 #define PCI_DEVICE_ID_38C1600_REV1 0x2700 78 79 #define PortAddr unsigned int /* port address size */ 80 #define inp(port) inb(port) 81 #define outp(port, byte) outb((byte), (port)) 82 83 #define inpw(port) inw(port) 84 #define outpw(port, word) outw((word), (port)) 85 86 #define ASC_MAX_SG_QUEUE 7 87 #define ASC_MAX_SG_LIST 255 88 89 #define ASC_CS_TYPE unsigned short 90 91 #define ASC_IS_ISA (0x0001) 92 #define ASC_IS_ISAPNP (0x0081) 93 #define ASC_IS_EISA (0x0002) 94 #define ASC_IS_PCI (0x0004) 95 #define ASC_IS_PCI_ULTRA (0x0104) 96 #define ASC_IS_PCMCIA (0x0008) 97 #define ASC_IS_MCA (0x0020) 98 #define ASC_IS_VL (0x0040) 99 #define ASC_IS_WIDESCSI_16 (0x0100) 100 #define ASC_IS_WIDESCSI_32 (0x0200) 101 #define ASC_IS_BIG_ENDIAN (0x8000) 102 103 #define ASC_CHIP_MIN_VER_VL (0x01) 104 #define ASC_CHIP_MAX_VER_VL (0x07) 105 #define ASC_CHIP_MIN_VER_PCI (0x09) 106 #define ASC_CHIP_MAX_VER_PCI (0x0F) 107 #define ASC_CHIP_VER_PCI_BIT (0x08) 108 #define ASC_CHIP_MIN_VER_ISA (0x11) 109 #define ASC_CHIP_MIN_VER_ISA_PNP (0x21) 110 #define ASC_CHIP_MAX_VER_ISA (0x27) 111 #define ASC_CHIP_VER_ISA_BIT (0x30) 112 #define ASC_CHIP_VER_ISAPNP_BIT (0x20) 113 #define ASC_CHIP_VER_ASYN_BUG (0x21) 114 #define ASC_CHIP_VER_PCI 0x08 115 #define ASC_CHIP_VER_PCI_ULTRA_3150 (ASC_CHIP_VER_PCI | 0x02) 116 #define ASC_CHIP_VER_PCI_ULTRA_3050 (ASC_CHIP_VER_PCI | 0x03) 117 #define ASC_CHIP_MIN_VER_EISA (0x41) 118 #define ASC_CHIP_MAX_VER_EISA (0x47) 119 #define ASC_CHIP_VER_EISA_BIT (0x40) 120 #define ASC_CHIP_LATEST_VER_EISA ((ASC_CHIP_MIN_VER_EISA - 1) + 3) 121 #define ASC_MAX_VL_DMA_COUNT (0x07FFFFFFL) 122 #define ASC_MAX_PCI_DMA_COUNT (0xFFFFFFFFL) 123 #define ASC_MAX_ISA_DMA_COUNT (0x00FFFFFFL) 124 125 #define ASC_SCSI_ID_BITS 3 126 #define ASC_SCSI_TIX_TYPE uchar 127 #define ASC_ALL_DEVICE_BIT_SET 0xFF 128 #define ASC_SCSI_BIT_ID_TYPE uchar 129 #define ASC_MAX_TID 7 130 #define ASC_MAX_LUN 7 131 #define ASC_SCSI_WIDTH_BIT_SET 0xFF 132 #define ASC_MAX_SENSE_LEN 32 133 #define ASC_MIN_SENSE_LEN 14 134 #define ASC_SCSI_RESET_HOLD_TIME_US 60 135 136 /* 137 * Narrow boards only support 12-byte commands, while wide boards 138 * extend to 16-byte commands. 139 */ 140 #define ASC_MAX_CDB_LEN 12 141 #define ADV_MAX_CDB_LEN 16 142 143 #define MS_SDTR_LEN 0x03 144 #define MS_WDTR_LEN 0x02 145 146 #define ASC_SG_LIST_PER_Q 7 147 #define QS_FREE 0x00 148 #define QS_READY 0x01 149 #define QS_DISC1 0x02 150 #define QS_DISC2 0x04 151 #define QS_BUSY 0x08 152 #define QS_ABORTED 0x40 153 #define QS_DONE 0x80 154 #define QC_NO_CALLBACK 0x01 155 #define QC_SG_SWAP_QUEUE 0x02 156 #define QC_SG_HEAD 0x04 157 #define QC_DATA_IN 0x08 158 #define QC_DATA_OUT 0x10 159 #define QC_URGENT 0x20 160 #define QC_MSG_OUT 0x40 161 #define QC_REQ_SENSE 0x80 162 #define QCSG_SG_XFER_LIST 0x02 163 #define QCSG_SG_XFER_MORE 0x04 164 #define QCSG_SG_XFER_END 0x08 165 #define QD_IN_PROGRESS 0x00 166 #define QD_NO_ERROR 0x01 167 #define QD_ABORTED_BY_HOST 0x02 168 #define QD_WITH_ERROR 0x04 169 #define QD_INVALID_REQUEST 0x80 170 #define QD_INVALID_HOST_NUM 0x81 171 #define QD_INVALID_DEVICE 0x82 172 #define QD_ERR_INTERNAL 0xFF 173 #define QHSTA_NO_ERROR 0x00 174 #define QHSTA_M_SEL_TIMEOUT 0x11 175 #define QHSTA_M_DATA_OVER_RUN 0x12 176 #define QHSTA_M_DATA_UNDER_RUN 0x12 177 #define QHSTA_M_UNEXPECTED_BUS_FREE 0x13 178 #define QHSTA_M_BAD_BUS_PHASE_SEQ 0x14 179 #define QHSTA_D_QDONE_SG_LIST_CORRUPTED 0x21 180 #define QHSTA_D_ASC_DVC_ERROR_CODE_SET 0x22 181 #define QHSTA_D_HOST_ABORT_FAILED 0x23 182 #define QHSTA_D_EXE_SCSI_Q_FAILED 0x24 183 #define QHSTA_D_EXE_SCSI_Q_BUSY_TIMEOUT 0x25 184 #define QHSTA_D_ASPI_NO_BUF_POOL 0x26 185 #define QHSTA_M_WTM_TIMEOUT 0x41 186 #define QHSTA_M_BAD_CMPL_STATUS_IN 0x42 187 #define QHSTA_M_NO_AUTO_REQ_SENSE 0x43 188 #define QHSTA_M_AUTO_REQ_SENSE_FAIL 0x44 189 #define QHSTA_M_TARGET_STATUS_BUSY 0x45 190 #define QHSTA_M_BAD_TAG_CODE 0x46 191 #define QHSTA_M_BAD_QUEUE_FULL_OR_BUSY 0x47 192 #define QHSTA_M_HUNG_REQ_SCSI_BUS_RESET 0x48 193 #define QHSTA_D_LRAM_CMP_ERROR 0x81 194 #define QHSTA_M_MICRO_CODE_ERROR_HALT 0xA1 195 #define ASC_FLAG_SCSIQ_REQ 0x01 196 #define ASC_FLAG_BIOS_SCSIQ_REQ 0x02 197 #define ASC_FLAG_BIOS_ASYNC_IO 0x04 198 #define ASC_FLAG_SRB_LINEAR_ADDR 0x08 199 #define ASC_FLAG_WIN16 0x10 200 #define ASC_FLAG_WIN32 0x20 201 #define ASC_FLAG_ISA_OVER_16MB 0x40 202 #define ASC_FLAG_DOS_VM_CALLBACK 0x80 203 #define ASC_TAG_FLAG_EXTRA_BYTES 0x10 204 #define ASC_TAG_FLAG_DISABLE_DISCONNECT 0x04 205 #define ASC_TAG_FLAG_DISABLE_ASYN_USE_SYN_FIX 0x08 206 #define ASC_TAG_FLAG_DISABLE_CHK_COND_INT_HOST 0x40 207 #define ASC_SCSIQ_CPY_BEG 4 208 #define ASC_SCSIQ_SGHD_CPY_BEG 2 209 #define ASC_SCSIQ_B_FWD 0 210 #define ASC_SCSIQ_B_BWD 1 211 #define ASC_SCSIQ_B_STATUS 2 212 #define ASC_SCSIQ_B_QNO 3 213 #define ASC_SCSIQ_B_CNTL 4 214 #define ASC_SCSIQ_B_SG_QUEUE_CNT 5 215 #define ASC_SCSIQ_D_DATA_ADDR 8 216 #define ASC_SCSIQ_D_DATA_CNT 12 217 #define ASC_SCSIQ_B_SENSE_LEN 20 218 #define ASC_SCSIQ_DONE_INFO_BEG 22 219 #define ASC_SCSIQ_D_SRBPTR 22 220 #define ASC_SCSIQ_B_TARGET_IX 26 221 #define ASC_SCSIQ_B_CDB_LEN 28 222 #define ASC_SCSIQ_B_TAG_CODE 29 223 #define ASC_SCSIQ_W_VM_ID 30 224 #define ASC_SCSIQ_DONE_STATUS 32 225 #define ASC_SCSIQ_HOST_STATUS 33 226 #define ASC_SCSIQ_SCSI_STATUS 34 227 #define ASC_SCSIQ_CDB_BEG 36 228 #define ASC_SCSIQ_DW_REMAIN_XFER_ADDR 56 229 #define ASC_SCSIQ_DW_REMAIN_XFER_CNT 60 230 #define ASC_SCSIQ_B_FIRST_SG_WK_QP 48 231 #define ASC_SCSIQ_B_SG_WK_QP 49 232 #define ASC_SCSIQ_B_SG_WK_IX 50 233 #define ASC_SCSIQ_W_ALT_DC1 52 234 #define ASC_SCSIQ_B_LIST_CNT 6 235 #define ASC_SCSIQ_B_CUR_LIST_CNT 7 236 #define ASC_SGQ_B_SG_CNTL 4 237 #define ASC_SGQ_B_SG_HEAD_QP 5 238 #define ASC_SGQ_B_SG_LIST_CNT 6 239 #define ASC_SGQ_B_SG_CUR_LIST_CNT 7 240 #define ASC_SGQ_LIST_BEG 8 241 #define ASC_DEF_SCSI1_QNG 4 242 #define ASC_MAX_SCSI1_QNG 4 243 #define ASC_DEF_SCSI2_QNG 16 244 #define ASC_MAX_SCSI2_QNG 32 245 #define ASC_TAG_CODE_MASK 0x23 246 #define ASC_STOP_REQ_RISC_STOP 0x01 247 #define ASC_STOP_ACK_RISC_STOP 0x03 248 #define ASC_STOP_CLEAN_UP_BUSY_Q 0x10 249 #define ASC_STOP_CLEAN_UP_DISC_Q 0x20 250 #define ASC_STOP_HOST_REQ_RISC_HALT 0x40 251 #define ASC_TIDLUN_TO_IX(tid, lun) (ASC_SCSI_TIX_TYPE)((tid) + ((lun)<<ASC_SCSI_ID_BITS)) 252 #define ASC_TID_TO_TARGET_ID(tid) (ASC_SCSI_BIT_ID_TYPE)(0x01 << (tid)) 253 #define ASC_TIX_TO_TARGET_ID(tix) (0x01 << ((tix) & ASC_MAX_TID)) 254 #define ASC_TIX_TO_TID(tix) ((tix) & ASC_MAX_TID) 255 #define ASC_TID_TO_TIX(tid) ((tid) & ASC_MAX_TID) 256 #define ASC_TIX_TO_LUN(tix) (((tix) >> ASC_SCSI_ID_BITS) & ASC_MAX_LUN) 257 #define ASC_QNO_TO_QADDR(q_no) ((ASC_QADR_BEG)+((int)(q_no) << 6)) 258 259 typedef struct asc_scsiq_1 { 260 uchar status; 261 uchar q_no; 262 uchar cntl; 263 uchar sg_queue_cnt; 264 uchar target_id; 265 uchar target_lun; 266 __le32 data_addr; 267 __le32 data_cnt; 268 __le32 sense_addr; 269 uchar sense_len; 270 uchar extra_bytes; 271 } ASC_SCSIQ_1; 272 273 typedef struct asc_scsiq_2 { 274 u32 srb_tag; 275 uchar target_ix; 276 uchar flag; 277 uchar cdb_len; 278 uchar tag_code; 279 ushort vm_id; 280 } ASC_SCSIQ_2; 281 282 typedef struct asc_scsiq_3 { 283 uchar done_stat; 284 uchar host_stat; 285 uchar scsi_stat; 286 uchar scsi_msg; 287 } ASC_SCSIQ_3; 288 289 typedef struct asc_scsiq_4 { 290 uchar cdb[ASC_MAX_CDB_LEN]; 291 uchar y_first_sg_list_qp; 292 uchar y_working_sg_qp; 293 uchar y_working_sg_ix; 294 uchar y_res; 295 ushort x_req_count; 296 ushort x_reconnect_rtn; 297 __le32 x_saved_data_addr; 298 __le32 x_saved_data_cnt; 299 } ASC_SCSIQ_4; 300 301 typedef struct asc_q_done_info { 302 ASC_SCSIQ_2 d2; 303 ASC_SCSIQ_3 d3; 304 uchar q_status; 305 uchar q_no; 306 uchar cntl; 307 uchar sense_len; 308 uchar extra_bytes; 309 uchar res; 310 u32 remain_bytes; 311 } ASC_QDONE_INFO; 312 313 typedef struct asc_sg_list { 314 __le32 addr; 315 __le32 bytes; 316 } ASC_SG_LIST; 317 318 typedef struct asc_sg_head { 319 ushort entry_cnt; 320 ushort queue_cnt; 321 ushort entry_to_copy; 322 ushort res; 323 ASC_SG_LIST sg_list[0]; 324 } ASC_SG_HEAD; 325 326 typedef struct asc_scsi_q { 327 ASC_SCSIQ_1 q1; 328 ASC_SCSIQ_2 q2; 329 uchar *cdbptr; 330 ASC_SG_HEAD *sg_head; 331 ushort remain_sg_entry_cnt; 332 ushort next_sg_index; 333 } ASC_SCSI_Q; 334 335 typedef struct asc_scsi_bios_req_q { 336 ASC_SCSIQ_1 r1; 337 ASC_SCSIQ_2 r2; 338 uchar *cdbptr; 339 ASC_SG_HEAD *sg_head; 340 uchar *sense_ptr; 341 ASC_SCSIQ_3 r3; 342 uchar cdb[ASC_MAX_CDB_LEN]; 343 uchar sense[ASC_MIN_SENSE_LEN]; 344 } ASC_SCSI_BIOS_REQ_Q; 345 346 typedef struct asc_risc_q { 347 uchar fwd; 348 uchar bwd; 349 ASC_SCSIQ_1 i1; 350 ASC_SCSIQ_2 i2; 351 ASC_SCSIQ_3 i3; 352 ASC_SCSIQ_4 i4; 353 } ASC_RISC_Q; 354 355 typedef struct asc_sg_list_q { 356 uchar seq_no; 357 uchar q_no; 358 uchar cntl; 359 uchar sg_head_qp; 360 uchar sg_list_cnt; 361 uchar sg_cur_list_cnt; 362 } ASC_SG_LIST_Q; 363 364 typedef struct asc_risc_sg_list_q { 365 uchar fwd; 366 uchar bwd; 367 ASC_SG_LIST_Q sg; 368 ASC_SG_LIST sg_list[7]; 369 } ASC_RISC_SG_LIST_Q; 370 371 #define ASCQ_ERR_Q_STATUS 0x0D 372 #define ASCQ_ERR_CUR_QNG 0x17 373 #define ASCQ_ERR_SG_Q_LINKS 0x18 374 #define ASCQ_ERR_ISR_RE_ENTRY 0x1A 375 #define ASCQ_ERR_CRITICAL_RE_ENTRY 0x1B 376 #define ASCQ_ERR_ISR_ON_CRITICAL 0x1C 377 378 /* 379 * Warning code values are set in ASC_DVC_VAR 'warn_code'. 380 */ 381 #define ASC_WARN_NO_ERROR 0x0000 382 #define ASC_WARN_IO_PORT_ROTATE 0x0001 383 #define ASC_WARN_EEPROM_CHKSUM 0x0002 384 #define ASC_WARN_IRQ_MODIFIED 0x0004 385 #define ASC_WARN_AUTO_CONFIG 0x0008 386 #define ASC_WARN_CMD_QNG_CONFLICT 0x0010 387 #define ASC_WARN_EEPROM_RECOVER 0x0020 388 #define ASC_WARN_CFG_MSW_RECOVER 0x0040 389 390 /* 391 * Error code values are set in {ASC/ADV}_DVC_VAR 'err_code'. 392 */ 393 #define ASC_IERR_NO_CARRIER 0x0001 /* No more carrier memory */ 394 #define ASC_IERR_MCODE_CHKSUM 0x0002 /* micro code check sum error */ 395 #define ASC_IERR_SET_PC_ADDR 0x0004 396 #define ASC_IERR_START_STOP_CHIP 0x0008 /* start/stop chip failed */ 397 #define ASC_IERR_ILLEGAL_CONNECTION 0x0010 /* Illegal cable connection */ 398 #define ASC_IERR_SINGLE_END_DEVICE 0x0020 /* SE device on DIFF bus */ 399 #define ASC_IERR_REVERSED_CABLE 0x0040 /* Narrow flat cable reversed */ 400 #define ASC_IERR_SET_SCSI_ID 0x0080 /* set SCSI ID failed */ 401 #define ASC_IERR_HVD_DEVICE 0x0100 /* HVD device on LVD port */ 402 #define ASC_IERR_BAD_SIGNATURE 0x0200 /* signature not found */ 403 #define ASC_IERR_NO_BUS_TYPE 0x0400 404 #define ASC_IERR_BIST_PRE_TEST 0x0800 /* BIST pre-test error */ 405 #define ASC_IERR_BIST_RAM_TEST 0x1000 /* BIST RAM test error */ 406 #define ASC_IERR_BAD_CHIPTYPE 0x2000 /* Invalid chip_type setting */ 407 408 #define ASC_DEF_MAX_TOTAL_QNG (0xF0) 409 #define ASC_MIN_TAG_Q_PER_DVC (0x04) 410 #define ASC_MIN_FREE_Q (0x02) 411 #define ASC_MIN_TOTAL_QNG ((ASC_MAX_SG_QUEUE)+(ASC_MIN_FREE_Q)) 412 #define ASC_MAX_TOTAL_QNG 240 413 #define ASC_MAX_PCI_ULTRA_INRAM_TOTAL_QNG 16 414 #define ASC_MAX_PCI_ULTRA_INRAM_TAG_QNG 8 415 #define ASC_MAX_PCI_INRAM_TOTAL_QNG 20 416 #define ASC_MAX_INRAM_TAG_QNG 16 417 #define ASC_IOADR_GAP 0x10 418 #define ASC_SYN_MAX_OFFSET 0x0F 419 #define ASC_DEF_SDTR_OFFSET 0x0F 420 #define ASC_SDTR_ULTRA_PCI_10MB_INDEX 0x02 421 #define ASYN_SDTR_DATA_FIX_PCI_REV_AB 0x41 422 423 /* The narrow chip only supports a limited selection of transfer rates. 424 * These are encoded in the range 0..7 or 0..15 depending whether the chip 425 * is Ultra-capable or not. These tables let us convert from one to the other. 426 */ 427 static const unsigned char asc_syn_xfer_period[8] = { 428 25, 30, 35, 40, 50, 60, 70, 85 429 }; 430 431 static const unsigned char asc_syn_ultra_xfer_period[16] = { 432 12, 19, 25, 32, 38, 44, 50, 57, 63, 69, 75, 82, 88, 94, 100, 107 433 }; 434 435 typedef struct ext_msg { 436 uchar msg_type; 437 uchar msg_len; 438 uchar msg_req; 439 union { 440 struct { 441 uchar sdtr_xfer_period; 442 uchar sdtr_req_ack_offset; 443 } sdtr; 444 struct { 445 uchar wdtr_width; 446 } wdtr; 447 struct { 448 uchar mdp_b3; 449 uchar mdp_b2; 450 uchar mdp_b1; 451 uchar mdp_b0; 452 } mdp; 453 } u_ext_msg; 454 uchar res; 455 } EXT_MSG; 456 457 #define xfer_period u_ext_msg.sdtr.sdtr_xfer_period 458 #define req_ack_offset u_ext_msg.sdtr.sdtr_req_ack_offset 459 #define wdtr_width u_ext_msg.wdtr.wdtr_width 460 #define mdp_b3 u_ext_msg.mdp_b3 461 #define mdp_b2 u_ext_msg.mdp_b2 462 #define mdp_b1 u_ext_msg.mdp_b1 463 #define mdp_b0 u_ext_msg.mdp_b0 464 465 typedef struct asc_dvc_cfg { 466 ASC_SCSI_BIT_ID_TYPE can_tagged_qng; 467 ASC_SCSI_BIT_ID_TYPE cmd_qng_enabled; 468 ASC_SCSI_BIT_ID_TYPE disc_enable; 469 ASC_SCSI_BIT_ID_TYPE sdtr_enable; 470 uchar chip_scsi_id; 471 uchar isa_dma_speed; 472 uchar isa_dma_channel; 473 uchar chip_version; 474 ushort mcode_date; 475 ushort mcode_version; 476 uchar max_tag_qng[ASC_MAX_TID + 1]; 477 uchar sdtr_period_offset[ASC_MAX_TID + 1]; 478 uchar adapter_info[6]; 479 } ASC_DVC_CFG; 480 481 #define ASC_DEF_DVC_CNTL 0xFFFF 482 #define ASC_DEF_CHIP_SCSI_ID 7 483 #define ASC_DEF_ISA_DMA_SPEED 4 484 #define ASC_INIT_STATE_BEG_GET_CFG 0x0001 485 #define ASC_INIT_STATE_END_GET_CFG 0x0002 486 #define ASC_INIT_STATE_BEG_SET_CFG 0x0004 487 #define ASC_INIT_STATE_END_SET_CFG 0x0008 488 #define ASC_INIT_STATE_BEG_LOAD_MC 0x0010 489 #define ASC_INIT_STATE_END_LOAD_MC 0x0020 490 #define ASC_INIT_STATE_BEG_INQUIRY 0x0040 491 #define ASC_INIT_STATE_END_INQUIRY 0x0080 492 #define ASC_INIT_RESET_SCSI_DONE 0x0100 493 #define ASC_INIT_STATE_WITHOUT_EEP 0x8000 494 #define ASC_BUG_FIX_IF_NOT_DWB 0x0001 495 #define ASC_BUG_FIX_ASYN_USE_SYN 0x0002 496 #define ASC_MIN_TAGGED_CMD 7 497 #define ASC_MAX_SCSI_RESET_WAIT 30 498 #define ASC_OVERRUN_BSIZE 64 499 500 struct asc_dvc_var; /* Forward Declaration. */ 501 502 typedef struct asc_dvc_var { 503 PortAddr iop_base; 504 ushort err_code; 505 ushort dvc_cntl; 506 ushort bug_fix_cntl; 507 ushort bus_type; 508 ASC_SCSI_BIT_ID_TYPE init_sdtr; 509 ASC_SCSI_BIT_ID_TYPE sdtr_done; 510 ASC_SCSI_BIT_ID_TYPE use_tagged_qng; 511 ASC_SCSI_BIT_ID_TYPE unit_not_ready; 512 ASC_SCSI_BIT_ID_TYPE queue_full_or_busy; 513 ASC_SCSI_BIT_ID_TYPE start_motor; 514 uchar *overrun_buf; 515 dma_addr_t overrun_dma; 516 uchar scsi_reset_wait; 517 uchar chip_no; 518 bool is_in_int; 519 uchar max_total_qng; 520 uchar cur_total_qng; 521 uchar in_critical_cnt; 522 uchar last_q_shortage; 523 ushort init_state; 524 uchar cur_dvc_qng[ASC_MAX_TID + 1]; 525 uchar max_dvc_qng[ASC_MAX_TID + 1]; 526 ASC_SCSI_Q *scsiq_busy_head[ASC_MAX_TID + 1]; 527 ASC_SCSI_Q *scsiq_busy_tail[ASC_MAX_TID + 1]; 528 const uchar *sdtr_period_tbl; 529 ASC_DVC_CFG *cfg; 530 ASC_SCSI_BIT_ID_TYPE pci_fix_asyn_xfer_always; 531 char redo_scam; 532 ushort res2; 533 uchar dos_int13_table[ASC_MAX_TID + 1]; 534 unsigned int max_dma_count; 535 ASC_SCSI_BIT_ID_TYPE no_scam; 536 ASC_SCSI_BIT_ID_TYPE pci_fix_asyn_xfer; 537 uchar min_sdtr_index; 538 uchar max_sdtr_index; 539 struct asc_board *drv_ptr; 540 unsigned int uc_break; 541 } ASC_DVC_VAR; 542 543 typedef struct asc_dvc_inq_info { 544 uchar type[ASC_MAX_TID + 1][ASC_MAX_LUN + 1]; 545 } ASC_DVC_INQ_INFO; 546 547 typedef struct asc_cap_info { 548 u32 lba; 549 u32 blk_size; 550 } ASC_CAP_INFO; 551 552 typedef struct asc_cap_info_array { 553 ASC_CAP_INFO cap_info[ASC_MAX_TID + 1][ASC_MAX_LUN + 1]; 554 } ASC_CAP_INFO_ARRAY; 555 556 #define ASC_MCNTL_NO_SEL_TIMEOUT (ushort)0x0001 557 #define ASC_MCNTL_NULL_TARGET (ushort)0x0002 558 #define ASC_CNTL_INITIATOR (ushort)0x0001 559 #define ASC_CNTL_BIOS_GT_1GB (ushort)0x0002 560 #define ASC_CNTL_BIOS_GT_2_DISK (ushort)0x0004 561 #define ASC_CNTL_BIOS_REMOVABLE (ushort)0x0008 562 #define ASC_CNTL_NO_SCAM (ushort)0x0010 563 #define ASC_CNTL_INT_MULTI_Q (ushort)0x0080 564 #define ASC_CNTL_NO_LUN_SUPPORT (ushort)0x0040 565 #define ASC_CNTL_NO_VERIFY_COPY (ushort)0x0100 566 #define ASC_CNTL_RESET_SCSI (ushort)0x0200 567 #define ASC_CNTL_INIT_INQUIRY (ushort)0x0400 568 #define ASC_CNTL_INIT_VERBOSE (ushort)0x0800 569 #define ASC_CNTL_SCSI_PARITY (ushort)0x1000 570 #define ASC_CNTL_BURST_MODE (ushort)0x2000 571 #define ASC_CNTL_SDTR_ENABLE_ULTRA (ushort)0x4000 572 #define ASC_EEP_DVC_CFG_BEG_VL 2 573 #define ASC_EEP_MAX_DVC_ADDR_VL 15 574 #define ASC_EEP_DVC_CFG_BEG 32 575 #define ASC_EEP_MAX_DVC_ADDR 45 576 #define ASC_EEP_MAX_RETRY 20 577 578 /* 579 * These macros keep the chip SCSI id and ISA DMA speed 580 * bitfields in board order. C bitfields aren't portable 581 * between big and little-endian platforms so they are 582 * not used. 583 */ 584 585 #define ASC_EEP_GET_CHIP_ID(cfg) ((cfg)->id_speed & 0x0f) 586 #define ASC_EEP_GET_DMA_SPD(cfg) (((cfg)->id_speed & 0xf0) >> 4) 587 #define ASC_EEP_SET_CHIP_ID(cfg, sid) \ 588 ((cfg)->id_speed = ((cfg)->id_speed & 0xf0) | ((sid) & ASC_MAX_TID)) 589 #define ASC_EEP_SET_DMA_SPD(cfg, spd) \ 590 ((cfg)->id_speed = ((cfg)->id_speed & 0x0f) | ((spd) & 0x0f) << 4) 591 592 typedef struct asceep_config { 593 ushort cfg_lsw; 594 ushort cfg_msw; 595 uchar init_sdtr; 596 uchar disc_enable; 597 uchar use_cmd_qng; 598 uchar start_motor; 599 uchar max_total_qng; 600 uchar max_tag_qng; 601 uchar bios_scan; 602 uchar power_up_wait; 603 uchar no_scam; 604 uchar id_speed; /* low order 4 bits is chip scsi id */ 605 /* high order 4 bits is isa dma speed */ 606 uchar dos_int13_table[ASC_MAX_TID + 1]; 607 uchar adapter_info[6]; 608 ushort cntl; 609 ushort chksum; 610 } ASCEEP_CONFIG; 611 612 #define ASC_EEP_CMD_READ 0x80 613 #define ASC_EEP_CMD_WRITE 0x40 614 #define ASC_EEP_CMD_WRITE_ABLE 0x30 615 #define ASC_EEP_CMD_WRITE_DISABLE 0x00 616 #define ASCV_MSGOUT_BEG 0x0000 617 #define ASCV_MSGOUT_SDTR_PERIOD (ASCV_MSGOUT_BEG+3) 618 #define ASCV_MSGOUT_SDTR_OFFSET (ASCV_MSGOUT_BEG+4) 619 #define ASCV_BREAK_SAVED_CODE (ushort)0x0006 620 #define ASCV_MSGIN_BEG (ASCV_MSGOUT_BEG+8) 621 #define ASCV_MSGIN_SDTR_PERIOD (ASCV_MSGIN_BEG+3) 622 #define ASCV_MSGIN_SDTR_OFFSET (ASCV_MSGIN_BEG+4) 623 #define ASCV_SDTR_DATA_BEG (ASCV_MSGIN_BEG+8) 624 #define ASCV_SDTR_DONE_BEG (ASCV_SDTR_DATA_BEG+8) 625 #define ASCV_MAX_DVC_QNG_BEG (ushort)0x0020 626 #define ASCV_BREAK_ADDR (ushort)0x0028 627 #define ASCV_BREAK_NOTIFY_COUNT (ushort)0x002A 628 #define ASCV_BREAK_CONTROL (ushort)0x002C 629 #define ASCV_BREAK_HIT_COUNT (ushort)0x002E 630 631 #define ASCV_ASCDVC_ERR_CODE_W (ushort)0x0030 632 #define ASCV_MCODE_CHKSUM_W (ushort)0x0032 633 #define ASCV_MCODE_SIZE_W (ushort)0x0034 634 #define ASCV_STOP_CODE_B (ushort)0x0036 635 #define ASCV_DVC_ERR_CODE_B (ushort)0x0037 636 #define ASCV_OVERRUN_PADDR_D (ushort)0x0038 637 #define ASCV_OVERRUN_BSIZE_D (ushort)0x003C 638 #define ASCV_HALTCODE_W (ushort)0x0040 639 #define ASCV_CHKSUM_W (ushort)0x0042 640 #define ASCV_MC_DATE_W (ushort)0x0044 641 #define ASCV_MC_VER_W (ushort)0x0046 642 #define ASCV_NEXTRDY_B (ushort)0x0048 643 #define ASCV_DONENEXT_B (ushort)0x0049 644 #define ASCV_USE_TAGGED_QNG_B (ushort)0x004A 645 #define ASCV_SCSIBUSY_B (ushort)0x004B 646 #define ASCV_Q_DONE_IN_PROGRESS_B (ushort)0x004C 647 #define ASCV_CURCDB_B (ushort)0x004D 648 #define ASCV_RCLUN_B (ushort)0x004E 649 #define ASCV_BUSY_QHEAD_B (ushort)0x004F 650 #define ASCV_DISC1_QHEAD_B (ushort)0x0050 651 #define ASCV_DISC_ENABLE_B (ushort)0x0052 652 #define ASCV_CAN_TAGGED_QNG_B (ushort)0x0053 653 #define ASCV_HOSTSCSI_ID_B (ushort)0x0055 654 #define ASCV_MCODE_CNTL_B (ushort)0x0056 655 #define ASCV_NULL_TARGET_B (ushort)0x0057 656 #define ASCV_FREE_Q_HEAD_W (ushort)0x0058 657 #define ASCV_DONE_Q_TAIL_W (ushort)0x005A 658 #define ASCV_FREE_Q_HEAD_B (ushort)(ASCV_FREE_Q_HEAD_W+1) 659 #define ASCV_DONE_Q_TAIL_B (ushort)(ASCV_DONE_Q_TAIL_W+1) 660 #define ASCV_HOST_FLAG_B (ushort)0x005D 661 #define ASCV_TOTAL_READY_Q_B (ushort)0x0064 662 #define ASCV_VER_SERIAL_B (ushort)0x0065 663 #define ASCV_HALTCODE_SAVED_W (ushort)0x0066 664 #define ASCV_WTM_FLAG_B (ushort)0x0068 665 #define ASCV_RISC_FLAG_B (ushort)0x006A 666 #define ASCV_REQ_SG_LIST_QP (ushort)0x006B 667 #define ASC_HOST_FLAG_IN_ISR 0x01 668 #define ASC_HOST_FLAG_ACK_INT 0x02 669 #define ASC_RISC_FLAG_GEN_INT 0x01 670 #define ASC_RISC_FLAG_REQ_SG_LIST 0x02 671 #define IOP_CTRL (0x0F) 672 #define IOP_STATUS (0x0E) 673 #define IOP_INT_ACK IOP_STATUS 674 #define IOP_REG_IFC (0x0D) 675 #define IOP_SYN_OFFSET (0x0B) 676 #define IOP_EXTRA_CONTROL (0x0D) 677 #define IOP_REG_PC (0x0C) 678 #define IOP_RAM_ADDR (0x0A) 679 #define IOP_RAM_DATA (0x08) 680 #define IOP_EEP_DATA (0x06) 681 #define IOP_EEP_CMD (0x07) 682 #define IOP_VERSION (0x03) 683 #define IOP_CONFIG_HIGH (0x04) 684 #define IOP_CONFIG_LOW (0x02) 685 #define IOP_SIG_BYTE (0x01) 686 #define IOP_SIG_WORD (0x00) 687 #define IOP_REG_DC1 (0x0E) 688 #define IOP_REG_DC0 (0x0C) 689 #define IOP_REG_SB (0x0B) 690 #define IOP_REG_DA1 (0x0A) 691 #define IOP_REG_DA0 (0x08) 692 #define IOP_REG_SC (0x09) 693 #define IOP_DMA_SPEED (0x07) 694 #define IOP_REG_FLAG (0x07) 695 #define IOP_FIFO_H (0x06) 696 #define IOP_FIFO_L (0x04) 697 #define IOP_REG_ID (0x05) 698 #define IOP_REG_QP (0x03) 699 #define IOP_REG_IH (0x02) 700 #define IOP_REG_IX (0x01) 701 #define IOP_REG_AX (0x00) 702 #define IFC_REG_LOCK (0x00) 703 #define IFC_REG_UNLOCK (0x09) 704 #define IFC_WR_EN_FILTER (0x10) 705 #define IFC_RD_NO_EEPROM (0x10) 706 #define IFC_SLEW_RATE (0x20) 707 #define IFC_ACT_NEG (0x40) 708 #define IFC_INP_FILTER (0x80) 709 #define IFC_INIT_DEFAULT (IFC_ACT_NEG | IFC_REG_UNLOCK) 710 #define SC_SEL (uchar)(0x80) 711 #define SC_BSY (uchar)(0x40) 712 #define SC_ACK (uchar)(0x20) 713 #define SC_REQ (uchar)(0x10) 714 #define SC_ATN (uchar)(0x08) 715 #define SC_IO (uchar)(0x04) 716 #define SC_CD (uchar)(0x02) 717 #define SC_MSG (uchar)(0x01) 718 #define SEC_SCSI_CTL (uchar)(0x80) 719 #define SEC_ACTIVE_NEGATE (uchar)(0x40) 720 #define SEC_SLEW_RATE (uchar)(0x20) 721 #define SEC_ENABLE_FILTER (uchar)(0x10) 722 #define ASC_HALT_EXTMSG_IN (ushort)0x8000 723 #define ASC_HALT_CHK_CONDITION (ushort)0x8100 724 #define ASC_HALT_SS_QUEUE_FULL (ushort)0x8200 725 #define ASC_HALT_DISABLE_ASYN_USE_SYN_FIX (ushort)0x8300 726 #define ASC_HALT_ENABLE_ASYN_USE_SYN_FIX (ushort)0x8400 727 #define ASC_HALT_SDTR_REJECTED (ushort)0x4000 728 #define ASC_HALT_HOST_COPY_SG_LIST_TO_RISC ( ushort )0x2000 729 #define ASC_MAX_QNO 0xF8 730 #define ASC_DATA_SEC_BEG (ushort)0x0080 731 #define ASC_DATA_SEC_END (ushort)0x0080 732 #define ASC_CODE_SEC_BEG (ushort)0x0080 733 #define ASC_CODE_SEC_END (ushort)0x0080 734 #define ASC_QADR_BEG (0x4000) 735 #define ASC_QADR_USED (ushort)(ASC_MAX_QNO * 64) 736 #define ASC_QADR_END (ushort)0x7FFF 737 #define ASC_QLAST_ADR (ushort)0x7FC0 738 #define ASC_QBLK_SIZE 0x40 739 #define ASC_BIOS_DATA_QBEG 0xF8 740 #define ASC_MIN_ACTIVE_QNO 0x01 741 #define ASC_QLINK_END 0xFF 742 #define ASC_EEPROM_WORDS 0x10 743 #define ASC_MAX_MGS_LEN 0x10 744 #define ASC_BIOS_ADDR_DEF 0xDC00 745 #define ASC_BIOS_SIZE 0x3800 746 #define ASC_BIOS_RAM_OFF 0x3800 747 #define ASC_BIOS_RAM_SIZE 0x800 748 #define ASC_BIOS_MIN_ADDR 0xC000 749 #define ASC_BIOS_MAX_ADDR 0xEC00 750 #define ASC_BIOS_BANK_SIZE 0x0400 751 #define ASC_MCODE_START_ADDR 0x0080 752 #define ASC_CFG0_HOST_INT_ON 0x0020 753 #define ASC_CFG0_BIOS_ON 0x0040 754 #define ASC_CFG0_VERA_BURST_ON 0x0080 755 #define ASC_CFG0_SCSI_PARITY_ON 0x0800 756 #define ASC_CFG1_SCSI_TARGET_ON 0x0080 757 #define ASC_CFG1_LRAM_8BITS_ON 0x0800 758 #define ASC_CFG_MSW_CLR_MASK 0x3080 759 #define CSW_TEST1 (ASC_CS_TYPE)0x8000 760 #define CSW_AUTO_CONFIG (ASC_CS_TYPE)0x4000 761 #define CSW_RESERVED1 (ASC_CS_TYPE)0x2000 762 #define CSW_IRQ_WRITTEN (ASC_CS_TYPE)0x1000 763 #define CSW_33MHZ_SELECTED (ASC_CS_TYPE)0x0800 764 #define CSW_TEST2 (ASC_CS_TYPE)0x0400 765 #define CSW_TEST3 (ASC_CS_TYPE)0x0200 766 #define CSW_RESERVED2 (ASC_CS_TYPE)0x0100 767 #define CSW_DMA_DONE (ASC_CS_TYPE)0x0080 768 #define CSW_FIFO_RDY (ASC_CS_TYPE)0x0040 769 #define CSW_EEP_READ_DONE (ASC_CS_TYPE)0x0020 770 #define CSW_HALTED (ASC_CS_TYPE)0x0010 771 #define CSW_SCSI_RESET_ACTIVE (ASC_CS_TYPE)0x0008 772 #define CSW_PARITY_ERR (ASC_CS_TYPE)0x0004 773 #define CSW_SCSI_RESET_LATCH (ASC_CS_TYPE)0x0002 774 #define CSW_INT_PENDING (ASC_CS_TYPE)0x0001 775 #define CIW_CLR_SCSI_RESET_INT (ASC_CS_TYPE)0x1000 776 #define CIW_INT_ACK (ASC_CS_TYPE)0x0100 777 #define CIW_TEST1 (ASC_CS_TYPE)0x0200 778 #define CIW_TEST2 (ASC_CS_TYPE)0x0400 779 #define CIW_SEL_33MHZ (ASC_CS_TYPE)0x0800 780 #define CIW_IRQ_ACT (ASC_CS_TYPE)0x1000 781 #define CC_CHIP_RESET (uchar)0x80 782 #define CC_SCSI_RESET (uchar)0x40 783 #define CC_HALT (uchar)0x20 784 #define CC_SINGLE_STEP (uchar)0x10 785 #define CC_DMA_ABLE (uchar)0x08 786 #define CC_TEST (uchar)0x04 787 #define CC_BANK_ONE (uchar)0x02 788 #define CC_DIAG (uchar)0x01 789 #define ASC_1000_ID0W 0x04C1 790 #define ASC_1000_ID0W_FIX 0x00C1 791 #define ASC_1000_ID1B 0x25 792 #define ASC_EISA_REV_IOP_MASK (0x0C83) 793 #define ASC_EISA_CFG_IOP_MASK (0x0C86) 794 #define ASC_GET_EISA_SLOT(iop) (PortAddr)((iop) & 0xF000) 795 #define INS_HALTINT (ushort)0x6281 796 #define INS_HALT (ushort)0x6280 797 #define INS_SINT (ushort)0x6200 798 #define INS_RFLAG_WTM (ushort)0x7380 799 #define ASC_MC_SAVE_CODE_WSIZE 0x500 800 #define ASC_MC_SAVE_DATA_WSIZE 0x40 801 802 typedef struct asc_mc_saved { 803 ushort data[ASC_MC_SAVE_DATA_WSIZE]; 804 ushort code[ASC_MC_SAVE_CODE_WSIZE]; 805 } ASC_MC_SAVED; 806 807 #define AscGetQDoneInProgress(port) AscReadLramByte((port), ASCV_Q_DONE_IN_PROGRESS_B) 808 #define AscPutQDoneInProgress(port, val) AscWriteLramByte((port), ASCV_Q_DONE_IN_PROGRESS_B, val) 809 #define AscGetVarFreeQHead(port) AscReadLramWord((port), ASCV_FREE_Q_HEAD_W) 810 #define AscGetVarDoneQTail(port) AscReadLramWord((port), ASCV_DONE_Q_TAIL_W) 811 #define AscPutVarFreeQHead(port, val) AscWriteLramWord((port), ASCV_FREE_Q_HEAD_W, val) 812 #define AscPutVarDoneQTail(port, val) AscWriteLramWord((port), ASCV_DONE_Q_TAIL_W, val) 813 #define AscGetRiscVarFreeQHead(port) AscReadLramByte((port), ASCV_NEXTRDY_B) 814 #define AscGetRiscVarDoneQTail(port) AscReadLramByte((port), ASCV_DONENEXT_B) 815 #define AscPutRiscVarFreeQHead(port, val) AscWriteLramByte((port), ASCV_NEXTRDY_B, val) 816 #define AscPutRiscVarDoneQTail(port, val) AscWriteLramByte((port), ASCV_DONENEXT_B, val) 817 #define AscPutMCodeSDTRDoneAtID(port, id, data) AscWriteLramByte((port), (ushort)((ushort)ASCV_SDTR_DONE_BEG+(ushort)id), (data)) 818 #define AscGetMCodeSDTRDoneAtID(port, id) AscReadLramByte((port), (ushort)((ushort)ASCV_SDTR_DONE_BEG+(ushort)id)) 819 #define AscPutMCodeInitSDTRAtID(port, id, data) AscWriteLramByte((port), (ushort)((ushort)ASCV_SDTR_DATA_BEG+(ushort)id), data) 820 #define AscGetMCodeInitSDTRAtID(port, id) AscReadLramByte((port), (ushort)((ushort)ASCV_SDTR_DATA_BEG+(ushort)id)) 821 #define AscGetChipSignatureByte(port) (uchar)inp((port)+IOP_SIG_BYTE) 822 #define AscGetChipSignatureWord(port) (ushort)inpw((port)+IOP_SIG_WORD) 823 #define AscGetChipVerNo(port) (uchar)inp((port)+IOP_VERSION) 824 #define AscGetChipCfgLsw(port) (ushort)inpw((port)+IOP_CONFIG_LOW) 825 #define AscGetChipCfgMsw(port) (ushort)inpw((port)+IOP_CONFIG_HIGH) 826 #define AscSetChipCfgLsw(port, data) outpw((port)+IOP_CONFIG_LOW, data) 827 #define AscSetChipCfgMsw(port, data) outpw((port)+IOP_CONFIG_HIGH, data) 828 #define AscGetChipEEPCmd(port) (uchar)inp((port)+IOP_EEP_CMD) 829 #define AscSetChipEEPCmd(port, data) outp((port)+IOP_EEP_CMD, data) 830 #define AscGetChipEEPData(port) (ushort)inpw((port)+IOP_EEP_DATA) 831 #define AscSetChipEEPData(port, data) outpw((port)+IOP_EEP_DATA, data) 832 #define AscGetChipLramAddr(port) (ushort)inpw((PortAddr)((port)+IOP_RAM_ADDR)) 833 #define AscSetChipLramAddr(port, addr) outpw((PortAddr)((port)+IOP_RAM_ADDR), addr) 834 #define AscGetChipLramData(port) (ushort)inpw((port)+IOP_RAM_DATA) 835 #define AscSetChipLramData(port, data) outpw((port)+IOP_RAM_DATA, data) 836 #define AscGetChipIFC(port) (uchar)inp((port)+IOP_REG_IFC) 837 #define AscSetChipIFC(port, data) outp((port)+IOP_REG_IFC, data) 838 #define AscGetChipStatus(port) (ASC_CS_TYPE)inpw((port)+IOP_STATUS) 839 #define AscSetChipStatus(port, cs_val) outpw((port)+IOP_STATUS, cs_val) 840 #define AscGetChipControl(port) (uchar)inp((port)+IOP_CTRL) 841 #define AscSetChipControl(port, cc_val) outp((port)+IOP_CTRL, cc_val) 842 #define AscGetChipSyn(port) (uchar)inp((port)+IOP_SYN_OFFSET) 843 #define AscSetChipSyn(port, data) outp((port)+IOP_SYN_OFFSET, data) 844 #define AscSetPCAddr(port, data) outpw((port)+IOP_REG_PC, data) 845 #define AscGetPCAddr(port) (ushort)inpw((port)+IOP_REG_PC) 846 #define AscIsIntPending(port) (AscGetChipStatus(port) & (CSW_INT_PENDING | CSW_SCSI_RESET_LATCH)) 847 #define AscGetChipScsiID(port) ((AscGetChipCfgLsw(port) >> 8) & ASC_MAX_TID) 848 #define AscGetExtraControl(port) (uchar)inp((port)+IOP_EXTRA_CONTROL) 849 #define AscSetExtraControl(port, data) outp((port)+IOP_EXTRA_CONTROL, data) 850 #define AscReadChipAX(port) (ushort)inpw((port)+IOP_REG_AX) 851 #define AscWriteChipAX(port, data) outpw((port)+IOP_REG_AX, data) 852 #define AscReadChipIX(port) (uchar)inp((port)+IOP_REG_IX) 853 #define AscWriteChipIX(port, data) outp((port)+IOP_REG_IX, data) 854 #define AscReadChipIH(port) (ushort)inpw((port)+IOP_REG_IH) 855 #define AscWriteChipIH(port, data) outpw((port)+IOP_REG_IH, data) 856 #define AscReadChipQP(port) (uchar)inp((port)+IOP_REG_QP) 857 #define AscWriteChipQP(port, data) outp((port)+IOP_REG_QP, data) 858 #define AscReadChipFIFO_L(port) (ushort)inpw((port)+IOP_REG_FIFO_L) 859 #define AscWriteChipFIFO_L(port, data) outpw((port)+IOP_REG_FIFO_L, data) 860 #define AscReadChipFIFO_H(port) (ushort)inpw((port)+IOP_REG_FIFO_H) 861 #define AscWriteChipFIFO_H(port, data) outpw((port)+IOP_REG_FIFO_H, data) 862 #define AscReadChipDmaSpeed(port) (uchar)inp((port)+IOP_DMA_SPEED) 863 #define AscWriteChipDmaSpeed(port, data) outp((port)+IOP_DMA_SPEED, data) 864 #define AscReadChipDA0(port) (ushort)inpw((port)+IOP_REG_DA0) 865 #define AscWriteChipDA0(port) outpw((port)+IOP_REG_DA0, data) 866 #define AscReadChipDA1(port) (ushort)inpw((port)+IOP_REG_DA1) 867 #define AscWriteChipDA1(port) outpw((port)+IOP_REG_DA1, data) 868 #define AscReadChipDC0(port) (ushort)inpw((port)+IOP_REG_DC0) 869 #define AscWriteChipDC0(port) outpw((port)+IOP_REG_DC0, data) 870 #define AscReadChipDC1(port) (ushort)inpw((port)+IOP_REG_DC1) 871 #define AscWriteChipDC1(port) outpw((port)+IOP_REG_DC1, data) 872 #define AscReadChipDvcID(port) (uchar)inp((port)+IOP_REG_ID) 873 #define AscWriteChipDvcID(port, data) outp((port)+IOP_REG_ID, data) 874 875 #define AdvPortAddr void __iomem * /* Virtual memory address size */ 876 877 /* 878 * Define Adv Library required memory access macros. 879 */ 880 #define ADV_MEM_READB(addr) readb(addr) 881 #define ADV_MEM_READW(addr) readw(addr) 882 #define ADV_MEM_WRITEB(addr, byte) writeb(byte, addr) 883 #define ADV_MEM_WRITEW(addr, word) writew(word, addr) 884 #define ADV_MEM_WRITEDW(addr, dword) writel(dword, addr) 885 886 /* 887 * Define total number of simultaneous maximum element scatter-gather 888 * request blocks per wide adapter. ASC_DEF_MAX_HOST_QNG (253) is the 889 * maximum number of outstanding commands per wide host adapter. Each 890 * command uses one or more ADV_SG_BLOCK each with 15 scatter-gather 891 * elements. Allow each command to have at least one ADV_SG_BLOCK structure. 892 * This allows about 15 commands to have the maximum 17 ADV_SG_BLOCK 893 * structures or 255 scatter-gather elements. 894 */ 895 #define ADV_TOT_SG_BLOCK ASC_DEF_MAX_HOST_QNG 896 897 /* 898 * Define maximum number of scatter-gather elements per request. 899 */ 900 #define ADV_MAX_SG_LIST 255 901 #define NO_OF_SG_PER_BLOCK 15 902 903 #define ADV_EEP_DVC_CFG_BEGIN (0x00) 904 #define ADV_EEP_DVC_CFG_END (0x15) 905 #define ADV_EEP_DVC_CTL_BEGIN (0x16) /* location of OEM name */ 906 #define ADV_EEP_MAX_WORD_ADDR (0x1E) 907 908 #define ADV_EEP_DELAY_MS 100 909 910 #define ADV_EEPROM_BIG_ENDIAN 0x8000 /* EEPROM Bit 15 */ 911 #define ADV_EEPROM_BIOS_ENABLE 0x4000 /* EEPROM Bit 14 */ 912 /* 913 * For the ASC3550 Bit 13 is Termination Polarity control bit. 914 * For later ICs Bit 13 controls whether the CIS (Card Information 915 * Service Section) is loaded from EEPROM. 916 */ 917 #define ADV_EEPROM_TERM_POL 0x2000 /* EEPROM Bit 13 */ 918 #define ADV_EEPROM_CIS_LD 0x2000 /* EEPROM Bit 13 */ 919 /* 920 * ASC38C1600 Bit 11 921 * 922 * If EEPROM Bit 11 is 0 for Function 0, then Function 0 will specify 923 * INT A in the PCI Configuration Space Int Pin field. If it is 1, then 924 * Function 0 will specify INT B. 925 * 926 * If EEPROM Bit 11 is 0 for Function 1, then Function 1 will specify 927 * INT B in the PCI Configuration Space Int Pin field. If it is 1, then 928 * Function 1 will specify INT A. 929 */ 930 #define ADV_EEPROM_INTAB 0x0800 /* EEPROM Bit 11 */ 931 932 typedef struct adveep_3550_config { 933 /* Word Offset, Description */ 934 935 ushort cfg_lsw; /* 00 power up initialization */ 936 /* bit 13 set - Term Polarity Control */ 937 /* bit 14 set - BIOS Enable */ 938 /* bit 15 set - Big Endian Mode */ 939 ushort cfg_msw; /* 01 unused */ 940 ushort disc_enable; /* 02 disconnect enable */ 941 ushort wdtr_able; /* 03 Wide DTR able */ 942 ushort sdtr_able; /* 04 Synchronous DTR able */ 943 ushort start_motor; /* 05 send start up motor */ 944 ushort tagqng_able; /* 06 tag queuing able */ 945 ushort bios_scan; /* 07 BIOS device control */ 946 ushort scam_tolerant; /* 08 no scam */ 947 948 uchar adapter_scsi_id; /* 09 Host Adapter ID */ 949 uchar bios_boot_delay; /* power up wait */ 950 951 uchar scsi_reset_delay; /* 10 reset delay */ 952 uchar bios_id_lun; /* first boot device scsi id & lun */ 953 /* high nibble is lun */ 954 /* low nibble is scsi id */ 955 956 uchar termination; /* 11 0 - automatic */ 957 /* 1 - low off / high off */ 958 /* 2 - low off / high on */ 959 /* 3 - low on / high on */ 960 /* There is no low on / high off */ 961 962 uchar reserved1; /* reserved byte (not used) */ 963 964 ushort bios_ctrl; /* 12 BIOS control bits */ 965 /* bit 0 BIOS don't act as initiator. */ 966 /* bit 1 BIOS > 1 GB support */ 967 /* bit 2 BIOS > 2 Disk Support */ 968 /* bit 3 BIOS don't support removables */ 969 /* bit 4 BIOS support bootable CD */ 970 /* bit 5 BIOS scan enabled */ 971 /* bit 6 BIOS support multiple LUNs */ 972 /* bit 7 BIOS display of message */ 973 /* bit 8 SCAM disabled */ 974 /* bit 9 Reset SCSI bus during init. */ 975 /* bit 10 */ 976 /* bit 11 No verbose initialization. */ 977 /* bit 12 SCSI parity enabled */ 978 /* bit 13 */ 979 /* bit 14 */ 980 /* bit 15 */ 981 ushort ultra_able; /* 13 ULTRA speed able */ 982 ushort reserved2; /* 14 reserved */ 983 uchar max_host_qng; /* 15 maximum host queuing */ 984 uchar max_dvc_qng; /* maximum per device queuing */ 985 ushort dvc_cntl; /* 16 control bit for driver */ 986 ushort bug_fix; /* 17 control bit for bug fix */ 987 ushort serial_number_word1; /* 18 Board serial number word 1 */ 988 ushort serial_number_word2; /* 19 Board serial number word 2 */ 989 ushort serial_number_word3; /* 20 Board serial number word 3 */ 990 ushort check_sum; /* 21 EEP check sum */ 991 uchar oem_name[16]; /* 22 OEM name */ 992 ushort dvc_err_code; /* 30 last device driver error code */ 993 ushort adv_err_code; /* 31 last uc and Adv Lib error code */ 994 ushort adv_err_addr; /* 32 last uc error address */ 995 ushort saved_dvc_err_code; /* 33 saved last dev. driver error code */ 996 ushort saved_adv_err_code; /* 34 saved last uc and Adv Lib error code */ 997 ushort saved_adv_err_addr; /* 35 saved last uc error address */ 998 ushort num_of_err; /* 36 number of error */ 999 } ADVEEP_3550_CONFIG; 1000 1001 typedef struct adveep_38C0800_config { 1002 /* Word Offset, Description */ 1003 1004 ushort cfg_lsw; /* 00 power up initialization */ 1005 /* bit 13 set - Load CIS */ 1006 /* bit 14 set - BIOS Enable */ 1007 /* bit 15 set - Big Endian Mode */ 1008 ushort cfg_msw; /* 01 unused */ 1009 ushort disc_enable; /* 02 disconnect enable */ 1010 ushort wdtr_able; /* 03 Wide DTR able */ 1011 ushort sdtr_speed1; /* 04 SDTR Speed TID 0-3 */ 1012 ushort start_motor; /* 05 send start up motor */ 1013 ushort tagqng_able; /* 06 tag queuing able */ 1014 ushort bios_scan; /* 07 BIOS device control */ 1015 ushort scam_tolerant; /* 08 no scam */ 1016 1017 uchar adapter_scsi_id; /* 09 Host Adapter ID */ 1018 uchar bios_boot_delay; /* power up wait */ 1019 1020 uchar scsi_reset_delay; /* 10 reset delay */ 1021 uchar bios_id_lun; /* first boot device scsi id & lun */ 1022 /* high nibble is lun */ 1023 /* low nibble is scsi id */ 1024 1025 uchar termination_se; /* 11 0 - automatic */ 1026 /* 1 - low off / high off */ 1027 /* 2 - low off / high on */ 1028 /* 3 - low on / high on */ 1029 /* There is no low on / high off */ 1030 1031 uchar termination_lvd; /* 11 0 - automatic */ 1032 /* 1 - low off / high off */ 1033 /* 2 - low off / high on */ 1034 /* 3 - low on / high on */ 1035 /* There is no low on / high off */ 1036 1037 ushort bios_ctrl; /* 12 BIOS control bits */ 1038 /* bit 0 BIOS don't act as initiator. */ 1039 /* bit 1 BIOS > 1 GB support */ 1040 /* bit 2 BIOS > 2 Disk Support */ 1041 /* bit 3 BIOS don't support removables */ 1042 /* bit 4 BIOS support bootable CD */ 1043 /* bit 5 BIOS scan enabled */ 1044 /* bit 6 BIOS support multiple LUNs */ 1045 /* bit 7 BIOS display of message */ 1046 /* bit 8 SCAM disabled */ 1047 /* bit 9 Reset SCSI bus during init. */ 1048 /* bit 10 */ 1049 /* bit 11 No verbose initialization. */ 1050 /* bit 12 SCSI parity enabled */ 1051 /* bit 13 */ 1052 /* bit 14 */ 1053 /* bit 15 */ 1054 ushort sdtr_speed2; /* 13 SDTR speed TID 4-7 */ 1055 ushort sdtr_speed3; /* 14 SDTR speed TID 8-11 */ 1056 uchar max_host_qng; /* 15 maximum host queueing */ 1057 uchar max_dvc_qng; /* maximum per device queuing */ 1058 ushort dvc_cntl; /* 16 control bit for driver */ 1059 ushort sdtr_speed4; /* 17 SDTR speed 4 TID 12-15 */ 1060 ushort serial_number_word1; /* 18 Board serial number word 1 */ 1061 ushort serial_number_word2; /* 19 Board serial number word 2 */ 1062 ushort serial_number_word3; /* 20 Board serial number word 3 */ 1063 ushort check_sum; /* 21 EEP check sum */ 1064 uchar oem_name[16]; /* 22 OEM name */ 1065 ushort dvc_err_code; /* 30 last device driver error code */ 1066 ushort adv_err_code; /* 31 last uc and Adv Lib error code */ 1067 ushort adv_err_addr; /* 32 last uc error address */ 1068 ushort saved_dvc_err_code; /* 33 saved last dev. driver error code */ 1069 ushort saved_adv_err_code; /* 34 saved last uc and Adv Lib error code */ 1070 ushort saved_adv_err_addr; /* 35 saved last uc error address */ 1071 ushort reserved36; /* 36 reserved */ 1072 ushort reserved37; /* 37 reserved */ 1073 ushort reserved38; /* 38 reserved */ 1074 ushort reserved39; /* 39 reserved */ 1075 ushort reserved40; /* 40 reserved */ 1076 ushort reserved41; /* 41 reserved */ 1077 ushort reserved42; /* 42 reserved */ 1078 ushort reserved43; /* 43 reserved */ 1079 ushort reserved44; /* 44 reserved */ 1080 ushort reserved45; /* 45 reserved */ 1081 ushort reserved46; /* 46 reserved */ 1082 ushort reserved47; /* 47 reserved */ 1083 ushort reserved48; /* 48 reserved */ 1084 ushort reserved49; /* 49 reserved */ 1085 ushort reserved50; /* 50 reserved */ 1086 ushort reserved51; /* 51 reserved */ 1087 ushort reserved52; /* 52 reserved */ 1088 ushort reserved53; /* 53 reserved */ 1089 ushort reserved54; /* 54 reserved */ 1090 ushort reserved55; /* 55 reserved */ 1091 ushort cisptr_lsw; /* 56 CIS PTR LSW */ 1092 ushort cisprt_msw; /* 57 CIS PTR MSW */ 1093 ushort subsysvid; /* 58 SubSystem Vendor ID */ 1094 ushort subsysid; /* 59 SubSystem ID */ 1095 ushort reserved60; /* 60 reserved */ 1096 ushort reserved61; /* 61 reserved */ 1097 ushort reserved62; /* 62 reserved */ 1098 ushort reserved63; /* 63 reserved */ 1099 } ADVEEP_38C0800_CONFIG; 1100 1101 typedef struct adveep_38C1600_config { 1102 /* Word Offset, Description */ 1103 1104 ushort cfg_lsw; /* 00 power up initialization */ 1105 /* bit 11 set - Func. 0 INTB, Func. 1 INTA */ 1106 /* clear - Func. 0 INTA, Func. 1 INTB */ 1107 /* bit 13 set - Load CIS */ 1108 /* bit 14 set - BIOS Enable */ 1109 /* bit 15 set - Big Endian Mode */ 1110 ushort cfg_msw; /* 01 unused */ 1111 ushort disc_enable; /* 02 disconnect enable */ 1112 ushort wdtr_able; /* 03 Wide DTR able */ 1113 ushort sdtr_speed1; /* 04 SDTR Speed TID 0-3 */ 1114 ushort start_motor; /* 05 send start up motor */ 1115 ushort tagqng_able; /* 06 tag queuing able */ 1116 ushort bios_scan; /* 07 BIOS device control */ 1117 ushort scam_tolerant; /* 08 no scam */ 1118 1119 uchar adapter_scsi_id; /* 09 Host Adapter ID */ 1120 uchar bios_boot_delay; /* power up wait */ 1121 1122 uchar scsi_reset_delay; /* 10 reset delay */ 1123 uchar bios_id_lun; /* first boot device scsi id & lun */ 1124 /* high nibble is lun */ 1125 /* low nibble is scsi id */ 1126 1127 uchar termination_se; /* 11 0 - automatic */ 1128 /* 1 - low off / high off */ 1129 /* 2 - low off / high on */ 1130 /* 3 - low on / high on */ 1131 /* There is no low on / high off */ 1132 1133 uchar termination_lvd; /* 11 0 - automatic */ 1134 /* 1 - low off / high off */ 1135 /* 2 - low off / high on */ 1136 /* 3 - low on / high on */ 1137 /* There is no low on / high off */ 1138 1139 ushort bios_ctrl; /* 12 BIOS control bits */ 1140 /* bit 0 BIOS don't act as initiator. */ 1141 /* bit 1 BIOS > 1 GB support */ 1142 /* bit 2 BIOS > 2 Disk Support */ 1143 /* bit 3 BIOS don't support removables */ 1144 /* bit 4 BIOS support bootable CD */ 1145 /* bit 5 BIOS scan enabled */ 1146 /* bit 6 BIOS support multiple LUNs */ 1147 /* bit 7 BIOS display of message */ 1148 /* bit 8 SCAM disabled */ 1149 /* bit 9 Reset SCSI bus during init. */ 1150 /* bit 10 Basic Integrity Checking disabled */ 1151 /* bit 11 No verbose initialization. */ 1152 /* bit 12 SCSI parity enabled */ 1153 /* bit 13 AIPP (Asyn. Info. Ph. Prot.) dis. */ 1154 /* bit 14 */ 1155 /* bit 15 */ 1156 ushort sdtr_speed2; /* 13 SDTR speed TID 4-7 */ 1157 ushort sdtr_speed3; /* 14 SDTR speed TID 8-11 */ 1158 uchar max_host_qng; /* 15 maximum host queueing */ 1159 uchar max_dvc_qng; /* maximum per device queuing */ 1160 ushort dvc_cntl; /* 16 control bit for driver */ 1161 ushort sdtr_speed4; /* 17 SDTR speed 4 TID 12-15 */ 1162 ushort serial_number_word1; /* 18 Board serial number word 1 */ 1163 ushort serial_number_word2; /* 19 Board serial number word 2 */ 1164 ushort serial_number_word3; /* 20 Board serial number word 3 */ 1165 ushort check_sum; /* 21 EEP check sum */ 1166 uchar oem_name[16]; /* 22 OEM name */ 1167 ushort dvc_err_code; /* 30 last device driver error code */ 1168 ushort adv_err_code; /* 31 last uc and Adv Lib error code */ 1169 ushort adv_err_addr; /* 32 last uc error address */ 1170 ushort saved_dvc_err_code; /* 33 saved last dev. driver error code */ 1171 ushort saved_adv_err_code; /* 34 saved last uc and Adv Lib error code */ 1172 ushort saved_adv_err_addr; /* 35 saved last uc error address */ 1173 ushort reserved36; /* 36 reserved */ 1174 ushort reserved37; /* 37 reserved */ 1175 ushort reserved38; /* 38 reserved */ 1176 ushort reserved39; /* 39 reserved */ 1177 ushort reserved40; /* 40 reserved */ 1178 ushort reserved41; /* 41 reserved */ 1179 ushort reserved42; /* 42 reserved */ 1180 ushort reserved43; /* 43 reserved */ 1181 ushort reserved44; /* 44 reserved */ 1182 ushort reserved45; /* 45 reserved */ 1183 ushort reserved46; /* 46 reserved */ 1184 ushort reserved47; /* 47 reserved */ 1185 ushort reserved48; /* 48 reserved */ 1186 ushort reserved49; /* 49 reserved */ 1187 ushort reserved50; /* 50 reserved */ 1188 ushort reserved51; /* 51 reserved */ 1189 ushort reserved52; /* 52 reserved */ 1190 ushort reserved53; /* 53 reserved */ 1191 ushort reserved54; /* 54 reserved */ 1192 ushort reserved55; /* 55 reserved */ 1193 ushort cisptr_lsw; /* 56 CIS PTR LSW */ 1194 ushort cisprt_msw; /* 57 CIS PTR MSW */ 1195 ushort subsysvid; /* 58 SubSystem Vendor ID */ 1196 ushort subsysid; /* 59 SubSystem ID */ 1197 ushort reserved60; /* 60 reserved */ 1198 ushort reserved61; /* 61 reserved */ 1199 ushort reserved62; /* 62 reserved */ 1200 ushort reserved63; /* 63 reserved */ 1201 } ADVEEP_38C1600_CONFIG; 1202 1203 /* 1204 * EEPROM Commands 1205 */ 1206 #define ASC_EEP_CMD_DONE 0x0200 1207 1208 /* bios_ctrl */ 1209 #define BIOS_CTRL_BIOS 0x0001 1210 #define BIOS_CTRL_EXTENDED_XLAT 0x0002 1211 #define BIOS_CTRL_GT_2_DISK 0x0004 1212 #define BIOS_CTRL_BIOS_REMOVABLE 0x0008 1213 #define BIOS_CTRL_BOOTABLE_CD 0x0010 1214 #define BIOS_CTRL_MULTIPLE_LUN 0x0040 1215 #define BIOS_CTRL_DISPLAY_MSG 0x0080 1216 #define BIOS_CTRL_NO_SCAM 0x0100 1217 #define BIOS_CTRL_RESET_SCSI_BUS 0x0200 1218 #define BIOS_CTRL_INIT_VERBOSE 0x0800 1219 #define BIOS_CTRL_SCSI_PARITY 0x1000 1220 #define BIOS_CTRL_AIPP_DIS 0x2000 1221 1222 #define ADV_3550_MEMSIZE 0x2000 /* 8 KB Internal Memory */ 1223 1224 #define ADV_38C0800_MEMSIZE 0x4000 /* 16 KB Internal Memory */ 1225 1226 /* 1227 * XXX - Since ASC38C1600 Rev.3 has a local RAM failure issue, there is 1228 * a special 16K Adv Library and Microcode version. After the issue is 1229 * resolved, should restore 32K support. 1230 * 1231 * #define ADV_38C1600_MEMSIZE 0x8000L * 32 KB Internal Memory * 1232 */ 1233 #define ADV_38C1600_MEMSIZE 0x4000 /* 16 KB Internal Memory */ 1234 1235 /* 1236 * Byte I/O register address from base of 'iop_base'. 1237 */ 1238 #define IOPB_INTR_STATUS_REG 0x00 1239 #define IOPB_CHIP_ID_1 0x01 1240 #define IOPB_INTR_ENABLES 0x02 1241 #define IOPB_CHIP_TYPE_REV 0x03 1242 #define IOPB_RES_ADDR_4 0x04 1243 #define IOPB_RES_ADDR_5 0x05 1244 #define IOPB_RAM_DATA 0x06 1245 #define IOPB_RES_ADDR_7 0x07 1246 #define IOPB_FLAG_REG 0x08 1247 #define IOPB_RES_ADDR_9 0x09 1248 #define IOPB_RISC_CSR 0x0A 1249 #define IOPB_RES_ADDR_B 0x0B 1250 #define IOPB_RES_ADDR_C 0x0C 1251 #define IOPB_RES_ADDR_D 0x0D 1252 #define IOPB_SOFT_OVER_WR 0x0E 1253 #define IOPB_RES_ADDR_F 0x0F 1254 #define IOPB_MEM_CFG 0x10 1255 #define IOPB_RES_ADDR_11 0x11 1256 #define IOPB_GPIO_DATA 0x12 1257 #define IOPB_RES_ADDR_13 0x13 1258 #define IOPB_FLASH_PAGE 0x14 1259 #define IOPB_RES_ADDR_15 0x15 1260 #define IOPB_GPIO_CNTL 0x16 1261 #define IOPB_RES_ADDR_17 0x17 1262 #define IOPB_FLASH_DATA 0x18 1263 #define IOPB_RES_ADDR_19 0x19 1264 #define IOPB_RES_ADDR_1A 0x1A 1265 #define IOPB_RES_ADDR_1B 0x1B 1266 #define IOPB_RES_ADDR_1C 0x1C 1267 #define IOPB_RES_ADDR_1D 0x1D 1268 #define IOPB_RES_ADDR_1E 0x1E 1269 #define IOPB_RES_ADDR_1F 0x1F 1270 #define IOPB_DMA_CFG0 0x20 1271 #define IOPB_DMA_CFG1 0x21 1272 #define IOPB_TICKLE 0x22 1273 #define IOPB_DMA_REG_WR 0x23 1274 #define IOPB_SDMA_STATUS 0x24 1275 #define IOPB_SCSI_BYTE_CNT 0x25 1276 #define IOPB_HOST_BYTE_CNT 0x26 1277 #define IOPB_BYTE_LEFT_TO_XFER 0x27 1278 #define IOPB_BYTE_TO_XFER_0 0x28 1279 #define IOPB_BYTE_TO_XFER_1 0x29 1280 #define IOPB_BYTE_TO_XFER_2 0x2A 1281 #define IOPB_BYTE_TO_XFER_3 0x2B 1282 #define IOPB_ACC_GRP 0x2C 1283 #define IOPB_RES_ADDR_2D 0x2D 1284 #define IOPB_DEV_ID 0x2E 1285 #define IOPB_RES_ADDR_2F 0x2F 1286 #define IOPB_SCSI_DATA 0x30 1287 #define IOPB_RES_ADDR_31 0x31 1288 #define IOPB_RES_ADDR_32 0x32 1289 #define IOPB_SCSI_DATA_HSHK 0x33 1290 #define IOPB_SCSI_CTRL 0x34 1291 #define IOPB_RES_ADDR_35 0x35 1292 #define IOPB_RES_ADDR_36 0x36 1293 #define IOPB_RES_ADDR_37 0x37 1294 #define IOPB_RAM_BIST 0x38 1295 #define IOPB_PLL_TEST 0x39 1296 #define IOPB_PCI_INT_CFG 0x3A 1297 #define IOPB_RES_ADDR_3B 0x3B 1298 #define IOPB_RFIFO_CNT 0x3C 1299 #define IOPB_RES_ADDR_3D 0x3D 1300 #define IOPB_RES_ADDR_3E 0x3E 1301 #define IOPB_RES_ADDR_3F 0x3F 1302 1303 /* 1304 * Word I/O register address from base of 'iop_base'. 1305 */ 1306 #define IOPW_CHIP_ID_0 0x00 /* CID0 */ 1307 #define IOPW_CTRL_REG 0x02 /* CC */ 1308 #define IOPW_RAM_ADDR 0x04 /* LA */ 1309 #define IOPW_RAM_DATA 0x06 /* LD */ 1310 #define IOPW_RES_ADDR_08 0x08 1311 #define IOPW_RISC_CSR 0x0A /* CSR */ 1312 #define IOPW_SCSI_CFG0 0x0C /* CFG0 */ 1313 #define IOPW_SCSI_CFG1 0x0E /* CFG1 */ 1314 #define IOPW_RES_ADDR_10 0x10 1315 #define IOPW_SEL_MASK 0x12 /* SM */ 1316 #define IOPW_RES_ADDR_14 0x14 1317 #define IOPW_FLASH_ADDR 0x16 /* FA */ 1318 #define IOPW_RES_ADDR_18 0x18 1319 #define IOPW_EE_CMD 0x1A /* EC */ 1320 #define IOPW_EE_DATA 0x1C /* ED */ 1321 #define IOPW_SFIFO_CNT 0x1E /* SFC */ 1322 #define IOPW_RES_ADDR_20 0x20 1323 #define IOPW_Q_BASE 0x22 /* QB */ 1324 #define IOPW_QP 0x24 /* QP */ 1325 #define IOPW_IX 0x26 /* IX */ 1326 #define IOPW_SP 0x28 /* SP */ 1327 #define IOPW_PC 0x2A /* PC */ 1328 #define IOPW_RES_ADDR_2C 0x2C 1329 #define IOPW_RES_ADDR_2E 0x2E 1330 #define IOPW_SCSI_DATA 0x30 /* SD */ 1331 #define IOPW_SCSI_DATA_HSHK 0x32 /* SDH */ 1332 #define IOPW_SCSI_CTRL 0x34 /* SC */ 1333 #define IOPW_HSHK_CFG 0x36 /* HCFG */ 1334 #define IOPW_SXFR_STATUS 0x36 /* SXS */ 1335 #define IOPW_SXFR_CNTL 0x38 /* SXL */ 1336 #define IOPW_SXFR_CNTH 0x3A /* SXH */ 1337 #define IOPW_RES_ADDR_3C 0x3C 1338 #define IOPW_RFIFO_DATA 0x3E /* RFD */ 1339 1340 /* 1341 * Doubleword I/O register address from base of 'iop_base'. 1342 */ 1343 #define IOPDW_RES_ADDR_0 0x00 1344 #define IOPDW_RAM_DATA 0x04 1345 #define IOPDW_RES_ADDR_8 0x08 1346 #define IOPDW_RES_ADDR_C 0x0C 1347 #define IOPDW_RES_ADDR_10 0x10 1348 #define IOPDW_COMMA 0x14 1349 #define IOPDW_COMMB 0x18 1350 #define IOPDW_RES_ADDR_1C 0x1C 1351 #define IOPDW_SDMA_ADDR0 0x20 1352 #define IOPDW_SDMA_ADDR1 0x24 1353 #define IOPDW_SDMA_COUNT 0x28 1354 #define IOPDW_SDMA_ERROR 0x2C 1355 #define IOPDW_RDMA_ADDR0 0x30 1356 #define IOPDW_RDMA_ADDR1 0x34 1357 #define IOPDW_RDMA_COUNT 0x38 1358 #define IOPDW_RDMA_ERROR 0x3C 1359 1360 #define ADV_CHIP_ID_BYTE 0x25 1361 #define ADV_CHIP_ID_WORD 0x04C1 1362 1363 #define ADV_INTR_ENABLE_HOST_INTR 0x01 1364 #define ADV_INTR_ENABLE_SEL_INTR 0x02 1365 #define ADV_INTR_ENABLE_DPR_INTR 0x04 1366 #define ADV_INTR_ENABLE_RTA_INTR 0x08 1367 #define ADV_INTR_ENABLE_RMA_INTR 0x10 1368 #define ADV_INTR_ENABLE_RST_INTR 0x20 1369 #define ADV_INTR_ENABLE_DPE_INTR 0x40 1370 #define ADV_INTR_ENABLE_GLOBAL_INTR 0x80 1371 1372 #define ADV_INTR_STATUS_INTRA 0x01 1373 #define ADV_INTR_STATUS_INTRB 0x02 1374 #define ADV_INTR_STATUS_INTRC 0x04 1375 1376 #define ADV_RISC_CSR_STOP (0x0000) 1377 #define ADV_RISC_TEST_COND (0x2000) 1378 #define ADV_RISC_CSR_RUN (0x4000) 1379 #define ADV_RISC_CSR_SINGLE_STEP (0x8000) 1380 1381 #define ADV_CTRL_REG_HOST_INTR 0x0100 1382 #define ADV_CTRL_REG_SEL_INTR 0x0200 1383 #define ADV_CTRL_REG_DPR_INTR 0x0400 1384 #define ADV_CTRL_REG_RTA_INTR 0x0800 1385 #define ADV_CTRL_REG_RMA_INTR 0x1000 1386 #define ADV_CTRL_REG_RES_BIT14 0x2000 1387 #define ADV_CTRL_REG_DPE_INTR 0x4000 1388 #define ADV_CTRL_REG_POWER_DONE 0x8000 1389 #define ADV_CTRL_REG_ANY_INTR 0xFF00 1390 1391 #define ADV_CTRL_REG_CMD_RESET 0x00C6 1392 #define ADV_CTRL_REG_CMD_WR_IO_REG 0x00C5 1393 #define ADV_CTRL_REG_CMD_RD_IO_REG 0x00C4 1394 #define ADV_CTRL_REG_CMD_WR_PCI_CFG_SPACE 0x00C3 1395 #define ADV_CTRL_REG_CMD_RD_PCI_CFG_SPACE 0x00C2 1396 1397 #define ADV_TICKLE_NOP 0x00 1398 #define ADV_TICKLE_A 0x01 1399 #define ADV_TICKLE_B 0x02 1400 #define ADV_TICKLE_C 0x03 1401 1402 #define AdvIsIntPending(port) \ 1403 (AdvReadWordRegister(port, IOPW_CTRL_REG) & ADV_CTRL_REG_HOST_INTR) 1404 1405 /* 1406 * SCSI_CFG0 Register bit definitions 1407 */ 1408 #define TIMER_MODEAB 0xC000 /* Watchdog, Second, and Select. Timer Ctrl. */ 1409 #define PARITY_EN 0x2000 /* Enable SCSI Parity Error detection */ 1410 #define EVEN_PARITY 0x1000 /* Select Even Parity */ 1411 #define WD_LONG 0x0800 /* Watchdog Interval, 1: 57 min, 0: 13 sec */ 1412 #define QUEUE_128 0x0400 /* Queue Size, 1: 128 byte, 0: 64 byte */ 1413 #define PRIM_MODE 0x0100 /* Primitive SCSI mode */ 1414 #define SCAM_EN 0x0080 /* Enable SCAM selection */ 1415 #define SEL_TMO_LONG 0x0040 /* Sel/Resel Timeout, 1: 400 ms, 0: 1.6 ms */ 1416 #define CFRM_ID 0x0020 /* SCAM id sel. confirm., 1: fast, 0: 6.4 ms */ 1417 #define OUR_ID_EN 0x0010 /* Enable OUR_ID bits */ 1418 #define OUR_ID 0x000F /* SCSI ID */ 1419 1420 /* 1421 * SCSI_CFG1 Register bit definitions 1422 */ 1423 #define BIG_ENDIAN 0x8000 /* Enable Big Endian Mode MIO:15, EEP:15 */ 1424 #define TERM_POL 0x2000 /* Terminator Polarity Ctrl. MIO:13, EEP:13 */ 1425 #define SLEW_RATE 0x1000 /* SCSI output buffer slew rate */ 1426 #define FILTER_SEL 0x0C00 /* Filter Period Selection */ 1427 #define FLTR_DISABLE 0x0000 /* Input Filtering Disabled */ 1428 #define FLTR_11_TO_20NS 0x0800 /* Input Filtering 11ns to 20ns */ 1429 #define FLTR_21_TO_39NS 0x0C00 /* Input Filtering 21ns to 39ns */ 1430 #define ACTIVE_DBL 0x0200 /* Disable Active Negation */ 1431 #define DIFF_MODE 0x0100 /* SCSI differential Mode (Read-Only) */ 1432 #define DIFF_SENSE 0x0080 /* 1: No SE cables, 0: SE cable (Read-Only) */ 1433 #define TERM_CTL_SEL 0x0040 /* Enable TERM_CTL_H and TERM_CTL_L */ 1434 #define TERM_CTL 0x0030 /* External SCSI Termination Bits */ 1435 #define TERM_CTL_H 0x0020 /* Enable External SCSI Upper Termination */ 1436 #define TERM_CTL_L 0x0010 /* Enable External SCSI Lower Termination */ 1437 #define CABLE_DETECT 0x000F /* External SCSI Cable Connection Status */ 1438 1439 /* 1440 * Addendum for ASC-38C0800 Chip 1441 * 1442 * The ASC-38C1600 Chip uses the same definitions except that the 1443 * bus mode override bits [12:10] have been moved to byte register 1444 * offset 0xE (IOPB_SOFT_OVER_WR) bits [12:10]. The [12:10] bits in 1445 * SCSI_CFG1 are read-only and always available. Bit 14 (DIS_TERM_DRV) 1446 * is not needed. The [12:10] bits in IOPB_SOFT_OVER_WR are write-only. 1447 * Also each ASC-38C1600 function or channel uses only cable bits [5:4] 1448 * and [1:0]. Bits [14], [7:6], [3:2] are unused. 1449 */ 1450 #define DIS_TERM_DRV 0x4000 /* 1: Read c_det[3:0], 0: cannot read */ 1451 #define HVD_LVD_SE 0x1C00 /* Device Detect Bits */ 1452 #define HVD 0x1000 /* HVD Device Detect */ 1453 #define LVD 0x0800 /* LVD Device Detect */ 1454 #define SE 0x0400 /* SE Device Detect */ 1455 #define TERM_LVD 0x00C0 /* LVD Termination Bits */ 1456 #define TERM_LVD_HI 0x0080 /* Enable LVD Upper Termination */ 1457 #define TERM_LVD_LO 0x0040 /* Enable LVD Lower Termination */ 1458 #define TERM_SE 0x0030 /* SE Termination Bits */ 1459 #define TERM_SE_HI 0x0020 /* Enable SE Upper Termination */ 1460 #define TERM_SE_LO 0x0010 /* Enable SE Lower Termination */ 1461 #define C_DET_LVD 0x000C /* LVD Cable Detect Bits */ 1462 #define C_DET3 0x0008 /* Cable Detect for LVD External Wide */ 1463 #define C_DET2 0x0004 /* Cable Detect for LVD Internal Wide */ 1464 #define C_DET_SE 0x0003 /* SE Cable Detect Bits */ 1465 #define C_DET1 0x0002 /* Cable Detect for SE Internal Wide */ 1466 #define C_DET0 0x0001 /* Cable Detect for SE Internal Narrow */ 1467 1468 #define CABLE_ILLEGAL_A 0x7 1469 /* x 0 0 0 | on on | Illegal (all 3 connectors are used) */ 1470 1471 #define CABLE_ILLEGAL_B 0xB 1472 /* 0 x 0 0 | on on | Illegal (all 3 connectors are used) */ 1473 1474 /* 1475 * MEM_CFG Register bit definitions 1476 */ 1477 #define BIOS_EN 0x40 /* BIOS Enable MIO:14,EEP:14 */ 1478 #define FAST_EE_CLK 0x20 /* Diagnostic Bit */ 1479 #define RAM_SZ 0x1C /* Specify size of RAM to RISC */ 1480 #define RAM_SZ_2KB 0x00 /* 2 KB */ 1481 #define RAM_SZ_4KB 0x04 /* 4 KB */ 1482 #define RAM_SZ_8KB 0x08 /* 8 KB */ 1483 #define RAM_SZ_16KB 0x0C /* 16 KB */ 1484 #define RAM_SZ_32KB 0x10 /* 32 KB */ 1485 #define RAM_SZ_64KB 0x14 /* 64 KB */ 1486 1487 /* 1488 * DMA_CFG0 Register bit definitions 1489 * 1490 * This register is only accessible to the host. 1491 */ 1492 #define BC_THRESH_ENB 0x80 /* PCI DMA Start Conditions */ 1493 #define FIFO_THRESH 0x70 /* PCI DMA FIFO Threshold */ 1494 #define FIFO_THRESH_16B 0x00 /* 16 bytes */ 1495 #define FIFO_THRESH_32B 0x20 /* 32 bytes */ 1496 #define FIFO_THRESH_48B 0x30 /* 48 bytes */ 1497 #define FIFO_THRESH_64B 0x40 /* 64 bytes */ 1498 #define FIFO_THRESH_80B 0x50 /* 80 bytes (default) */ 1499 #define FIFO_THRESH_96B 0x60 /* 96 bytes */ 1500 #define FIFO_THRESH_112B 0x70 /* 112 bytes */ 1501 #define START_CTL 0x0C /* DMA start conditions */ 1502 #define START_CTL_TH 0x00 /* Wait threshold level (default) */ 1503 #define START_CTL_ID 0x04 /* Wait SDMA/SBUS idle */ 1504 #define START_CTL_THID 0x08 /* Wait threshold and SDMA/SBUS idle */ 1505 #define START_CTL_EMFU 0x0C /* Wait SDMA FIFO empty/full */ 1506 #define READ_CMD 0x03 /* Memory Read Method */ 1507 #define READ_CMD_MR 0x00 /* Memory Read */ 1508 #define READ_CMD_MRL 0x02 /* Memory Read Long */ 1509 #define READ_CMD_MRM 0x03 /* Memory Read Multiple (default) */ 1510 1511 /* 1512 * ASC-38C0800 RAM BIST Register bit definitions 1513 */ 1514 #define RAM_TEST_MODE 0x80 1515 #define PRE_TEST_MODE 0x40 1516 #define NORMAL_MODE 0x00 1517 #define RAM_TEST_DONE 0x10 1518 #define RAM_TEST_STATUS 0x0F 1519 #define RAM_TEST_HOST_ERROR 0x08 1520 #define RAM_TEST_INTRAM_ERROR 0x04 1521 #define RAM_TEST_RISC_ERROR 0x02 1522 #define RAM_TEST_SCSI_ERROR 0x01 1523 #define RAM_TEST_SUCCESS 0x00 1524 #define PRE_TEST_VALUE 0x05 1525 #define NORMAL_VALUE 0x00 1526 1527 /* 1528 * ASC38C1600 Definitions 1529 * 1530 * IOPB_PCI_INT_CFG Bit Field Definitions 1531 */ 1532 1533 #define INTAB_LD 0x80 /* Value loaded from EEPROM Bit 11. */ 1534 1535 /* 1536 * Bit 1 can be set to change the interrupt for the Function to operate in 1537 * Totem Pole mode. By default Bit 1 is 0 and the interrupt operates in 1538 * Open Drain mode. Both functions of the ASC38C1600 must be set to the same 1539 * mode, otherwise the operating mode is undefined. 1540 */ 1541 #define TOTEMPOLE 0x02 1542 1543 /* 1544 * Bit 0 can be used to change the Int Pin for the Function. The value is 1545 * 0 by default for both Functions with Function 0 using INT A and Function 1546 * B using INT B. For Function 0 if set, INT B is used. For Function 1 if set, 1547 * INT A is used. 1548 * 1549 * EEPROM Word 0 Bit 11 for each Function may change the initial Int Pin 1550 * value specified in the PCI Configuration Space. 1551 */ 1552 #define INTAB 0x01 1553 1554 /* 1555 * Adv Library Status Definitions 1556 */ 1557 #define ADV_TRUE 1 1558 #define ADV_FALSE 0 1559 #define ADV_SUCCESS 1 1560 #define ADV_BUSY 0 1561 #define ADV_ERROR (-1) 1562 1563 /* 1564 * ADV_DVC_VAR 'warn_code' values 1565 */ 1566 #define ASC_WARN_BUSRESET_ERROR 0x0001 /* SCSI Bus Reset error */ 1567 #define ASC_WARN_EEPROM_CHKSUM 0x0002 /* EEP check sum error */ 1568 #define ASC_WARN_EEPROM_TERMINATION 0x0004 /* EEP termination bad field */ 1569 #define ASC_WARN_ERROR 0xFFFF /* ADV_ERROR return */ 1570 1571 #define ADV_MAX_TID 15 /* max. target identifier */ 1572 #define ADV_MAX_LUN 7 /* max. logical unit number */ 1573 1574 /* 1575 * Fixed locations of microcode operating variables. 1576 */ 1577 #define ASC_MC_CODE_BEGIN_ADDR 0x0028 /* microcode start address */ 1578 #define ASC_MC_CODE_END_ADDR 0x002A /* microcode end address */ 1579 #define ASC_MC_CODE_CHK_SUM 0x002C /* microcode code checksum */ 1580 #define ASC_MC_VERSION_DATE 0x0038 /* microcode version */ 1581 #define ASC_MC_VERSION_NUM 0x003A /* microcode number */ 1582 #define ASC_MC_BIOSMEM 0x0040 /* BIOS RISC Memory Start */ 1583 #define ASC_MC_BIOSLEN 0x0050 /* BIOS RISC Memory Length */ 1584 #define ASC_MC_BIOS_SIGNATURE 0x0058 /* BIOS Signature 0x55AA */ 1585 #define ASC_MC_BIOS_VERSION 0x005A /* BIOS Version (2 bytes) */ 1586 #define ASC_MC_SDTR_SPEED1 0x0090 /* SDTR Speed for TID 0-3 */ 1587 #define ASC_MC_SDTR_SPEED2 0x0092 /* SDTR Speed for TID 4-7 */ 1588 #define ASC_MC_SDTR_SPEED3 0x0094 /* SDTR Speed for TID 8-11 */ 1589 #define ASC_MC_SDTR_SPEED4 0x0096 /* SDTR Speed for TID 12-15 */ 1590 #define ASC_MC_CHIP_TYPE 0x009A 1591 #define ASC_MC_INTRB_CODE 0x009B 1592 #define ASC_MC_WDTR_ABLE 0x009C 1593 #define ASC_MC_SDTR_ABLE 0x009E 1594 #define ASC_MC_TAGQNG_ABLE 0x00A0 1595 #define ASC_MC_DISC_ENABLE 0x00A2 1596 #define ASC_MC_IDLE_CMD_STATUS 0x00A4 1597 #define ASC_MC_IDLE_CMD 0x00A6 1598 #define ASC_MC_IDLE_CMD_PARAMETER 0x00A8 1599 #define ASC_MC_DEFAULT_SCSI_CFG0 0x00AC 1600 #define ASC_MC_DEFAULT_SCSI_CFG1 0x00AE 1601 #define ASC_MC_DEFAULT_MEM_CFG 0x00B0 1602 #define ASC_MC_DEFAULT_SEL_MASK 0x00B2 1603 #define ASC_MC_SDTR_DONE 0x00B6 1604 #define ASC_MC_NUMBER_OF_QUEUED_CMD 0x00C0 1605 #define ASC_MC_NUMBER_OF_MAX_CMD 0x00D0 1606 #define ASC_MC_DEVICE_HSHK_CFG_TABLE 0x0100 1607 #define ASC_MC_CONTROL_FLAG 0x0122 /* Microcode control flag. */ 1608 #define ASC_MC_WDTR_DONE 0x0124 1609 #define ASC_MC_CAM_MODE_MASK 0x015E /* CAM mode TID bitmask. */ 1610 #define ASC_MC_ICQ 0x0160 1611 #define ASC_MC_IRQ 0x0164 1612 #define ASC_MC_PPR_ABLE 0x017A 1613 1614 /* 1615 * BIOS LRAM variable absolute offsets. 1616 */ 1617 #define BIOS_CODESEG 0x54 1618 #define BIOS_CODELEN 0x56 1619 #define BIOS_SIGNATURE 0x58 1620 #define BIOS_VERSION 0x5A 1621 1622 /* 1623 * Microcode Control Flags 1624 * 1625 * Flags set by the Adv Library in RISC variable 'control_flag' (0x122) 1626 * and handled by the microcode. 1627 */ 1628 #define CONTROL_FLAG_IGNORE_PERR 0x0001 /* Ignore DMA Parity Errors */ 1629 #define CONTROL_FLAG_ENABLE_AIPP 0x0002 /* Enabled AIPP checking. */ 1630 1631 /* 1632 * ASC_MC_DEVICE_HSHK_CFG_TABLE microcode table or HSHK_CFG register format 1633 */ 1634 #define HSHK_CFG_WIDE_XFR 0x8000 1635 #define HSHK_CFG_RATE 0x0F00 1636 #define HSHK_CFG_OFFSET 0x001F 1637 1638 #define ASC_DEF_MAX_HOST_QNG 0xFD /* Max. number of host commands (253) */ 1639 #define ASC_DEF_MIN_HOST_QNG 0x10 /* Min. number of host commands (16) */ 1640 #define ASC_DEF_MAX_DVC_QNG 0x3F /* Max. number commands per device (63) */ 1641 #define ASC_DEF_MIN_DVC_QNG 0x04 /* Min. number commands per device (4) */ 1642 1643 #define ASC_QC_DATA_CHECK 0x01 /* Require ASC_QC_DATA_OUT set or clear. */ 1644 #define ASC_QC_DATA_OUT 0x02 /* Data out DMA transfer. */ 1645 #define ASC_QC_START_MOTOR 0x04 /* Send auto-start motor before request. */ 1646 #define ASC_QC_NO_OVERRUN 0x08 /* Don't report overrun. */ 1647 #define ASC_QC_FREEZE_TIDQ 0x10 /* Freeze TID queue after request. XXX TBD */ 1648 1649 #define ASC_QSC_NO_DISC 0x01 /* Don't allow disconnect for request. */ 1650 #define ASC_QSC_NO_TAGMSG 0x02 /* Don't allow tag queuing for request. */ 1651 #define ASC_QSC_NO_SYNC 0x04 /* Don't use Synch. transfer on request. */ 1652 #define ASC_QSC_NO_WIDE 0x08 /* Don't use Wide transfer on request. */ 1653 #define ASC_QSC_REDO_DTR 0x10 /* Renegotiate WDTR/SDTR before request. */ 1654 /* 1655 * Note: If a Tag Message is to be sent and neither ASC_QSC_HEAD_TAG or 1656 * ASC_QSC_ORDERED_TAG is set, then a Simple Tag Message (0x20) is used. 1657 */ 1658 #define ASC_QSC_HEAD_TAG 0x40 /* Use Head Tag Message (0x21). */ 1659 #define ASC_QSC_ORDERED_TAG 0x80 /* Use Ordered Tag Message (0x22). */ 1660 1661 /* 1662 * All fields here are accessed by the board microcode and need to be 1663 * little-endian. 1664 */ 1665 typedef struct adv_carr_t { 1666 __le32 carr_va; /* Carrier Virtual Address */ 1667 __le32 carr_pa; /* Carrier Physical Address */ 1668 __le32 areq_vpa; /* ADV_SCSI_REQ_Q Virtual or Physical Address */ 1669 /* 1670 * next_vpa [31:4] Carrier Virtual or Physical Next Pointer 1671 * 1672 * next_vpa [3:1] Reserved Bits 1673 * next_vpa [0] Done Flag set in Response Queue. 1674 */ 1675 __le32 next_vpa; 1676 } ADV_CARR_T; 1677 1678 /* 1679 * Mask used to eliminate low 4 bits of carrier 'next_vpa' field. 1680 */ 1681 #define ADV_NEXT_VPA_MASK 0xFFFFFFF0 1682 1683 #define ADV_RQ_DONE 0x00000001 1684 #define ADV_RQ_GOOD 0x00000002 1685 #define ADV_CQ_STOPPER 0x00000000 1686 1687 #define ADV_GET_CARRP(carrp) ((carrp) & ADV_NEXT_VPA_MASK) 1688 1689 /* 1690 * Each carrier is 64 bytes, and we need three additional 1691 * carrier for icq, irq, and the termination carrier. 1692 */ 1693 #define ADV_CARRIER_COUNT (ASC_DEF_MAX_HOST_QNG + 3) 1694 1695 #define ADV_CARRIER_BUFSIZE \ 1696 (ADV_CARRIER_COUNT * sizeof(ADV_CARR_T)) 1697 1698 #define ADV_CHIP_ASC3550 0x01 /* Ultra-Wide IC */ 1699 #define ADV_CHIP_ASC38C0800 0x02 /* Ultra2-Wide/LVD IC */ 1700 #define ADV_CHIP_ASC38C1600 0x03 /* Ultra3-Wide/LVD2 IC */ 1701 1702 /* 1703 * Adapter temporary configuration structure 1704 * 1705 * This structure can be discarded after initialization. Don't add 1706 * fields here needed after initialization. 1707 * 1708 * Field naming convention: 1709 * 1710 * *_enable indicates the field enables or disables a feature. The 1711 * value of the field is never reset. 1712 */ 1713 typedef struct adv_dvc_cfg { 1714 ushort disc_enable; /* enable disconnection */ 1715 uchar chip_version; /* chip version */ 1716 uchar termination; /* Term. Ctrl. bits 6-5 of SCSI_CFG1 register */ 1717 ushort control_flag; /* Microcode Control Flag */ 1718 ushort mcode_date; /* Microcode date */ 1719 ushort mcode_version; /* Microcode version */ 1720 ushort serial1; /* EEPROM serial number word 1 */ 1721 ushort serial2; /* EEPROM serial number word 2 */ 1722 ushort serial3; /* EEPROM serial number word 3 */ 1723 } ADV_DVC_CFG; 1724 1725 struct adv_dvc_var; 1726 struct adv_scsi_req_q; 1727 1728 typedef struct adv_sg_block { 1729 uchar reserved1; 1730 uchar reserved2; 1731 uchar reserved3; 1732 uchar sg_cnt; /* Valid entries in block. */ 1733 __le32 sg_ptr; /* Pointer to next sg block. */ 1734 struct { 1735 __le32 sg_addr; /* SG element address. */ 1736 __le32 sg_count; /* SG element count. */ 1737 } sg_list[NO_OF_SG_PER_BLOCK]; 1738 } ADV_SG_BLOCK; 1739 1740 /* 1741 * ADV_SCSI_REQ_Q - microcode request structure 1742 * 1743 * All fields in this structure up to byte 60 are used by the microcode. 1744 * The microcode makes assumptions about the size and ordering of fields 1745 * in this structure. Do not change the structure definition here without 1746 * coordinating the change with the microcode. 1747 * 1748 * All fields accessed by microcode must be maintained in little_endian 1749 * order. 1750 */ 1751 typedef struct adv_scsi_req_q { 1752 uchar cntl; /* Ucode flags and state (ASC_MC_QC_*). */ 1753 uchar target_cmd; 1754 uchar target_id; /* Device target identifier. */ 1755 uchar target_lun; /* Device target logical unit number. */ 1756 __le32 data_addr; /* Data buffer physical address. */ 1757 __le32 data_cnt; /* Data count. Ucode sets to residual. */ 1758 __le32 sense_addr; 1759 __le32 carr_pa; 1760 uchar mflag; 1761 uchar sense_len; 1762 uchar cdb_len; /* SCSI CDB length. Must <= 16 bytes. */ 1763 uchar scsi_cntl; 1764 uchar done_status; /* Completion status. */ 1765 uchar scsi_status; /* SCSI status byte. */ 1766 uchar host_status; /* Ucode host status. */ 1767 uchar sg_working_ix; 1768 uchar cdb[12]; /* SCSI CDB bytes 0-11. */ 1769 __le32 sg_real_addr; /* SG list physical address. */ 1770 __le32 scsiq_rptr; 1771 uchar cdb16[4]; /* SCSI CDB bytes 12-15. */ 1772 __le32 scsiq_ptr; 1773 __le32 carr_va; 1774 /* 1775 * End of microcode structure - 60 bytes. The rest of the structure 1776 * is used by the Adv Library and ignored by the microcode. 1777 */ 1778 u32 srb_tag; 1779 ADV_SG_BLOCK *sg_list_ptr; /* SG list virtual address. */ 1780 } ADV_SCSI_REQ_Q; 1781 1782 /* 1783 * The following two structures are used to process Wide Board requests. 1784 * 1785 * The ADV_SCSI_REQ_Q structure in adv_req_t is passed to the Adv Library 1786 * and microcode with the ADV_SCSI_REQ_Q field 'srb_tag' set to the 1787 * SCSI request tag. The adv_req_t structure 'cmndp' field in turn points 1788 * to the Mid-Level SCSI request structure. 1789 * 1790 * Zero or more ADV_SG_BLOCK are used with each ADV_SCSI_REQ_Q. Each 1791 * ADV_SG_BLOCK structure holds 15 scatter-gather elements. Under Linux 1792 * up to 255 scatter-gather elements may be used per request or 1793 * ADV_SCSI_REQ_Q. 1794 * 1795 * Both structures must be 32 byte aligned. 1796 */ 1797 typedef struct adv_sgblk { 1798 ADV_SG_BLOCK sg_block; /* Sgblock structure. */ 1799 dma_addr_t sg_addr; /* Physical address */ 1800 struct adv_sgblk *next_sgblkp; /* Next scatter-gather structure. */ 1801 } adv_sgblk_t; 1802 1803 typedef struct adv_req { 1804 ADV_SCSI_REQ_Q scsi_req_q; /* Adv Library request structure. */ 1805 uchar align[24]; /* Request structure padding. */ 1806 struct scsi_cmnd *cmndp; /* Mid-Level SCSI command pointer. */ 1807 dma_addr_t req_addr; 1808 adv_sgblk_t *sgblkp; /* Adv Library scatter-gather pointer. */ 1809 } adv_req_t __aligned(32); 1810 1811 /* 1812 * Adapter operation variable structure. 1813 * 1814 * One structure is required per host adapter. 1815 * 1816 * Field naming convention: 1817 * 1818 * *_able indicates both whether a feature should be enabled or disabled 1819 * and whether a device isi capable of the feature. At initialization 1820 * this field may be set, but later if a device is found to be incapable 1821 * of the feature, the field is cleared. 1822 */ 1823 typedef struct adv_dvc_var { 1824 AdvPortAddr iop_base; /* I/O port address */ 1825 ushort err_code; /* fatal error code */ 1826 ushort bios_ctrl; /* BIOS control word, EEPROM word 12 */ 1827 ushort wdtr_able; /* try WDTR for a device */ 1828 ushort sdtr_able; /* try SDTR for a device */ 1829 ushort ultra_able; /* try SDTR Ultra speed for a device */ 1830 ushort sdtr_speed1; /* EEPROM SDTR Speed for TID 0-3 */ 1831 ushort sdtr_speed2; /* EEPROM SDTR Speed for TID 4-7 */ 1832 ushort sdtr_speed3; /* EEPROM SDTR Speed for TID 8-11 */ 1833 ushort sdtr_speed4; /* EEPROM SDTR Speed for TID 12-15 */ 1834 ushort tagqng_able; /* try tagged queuing with a device */ 1835 ushort ppr_able; /* PPR message capable per TID bitmask. */ 1836 uchar max_dvc_qng; /* maximum number of tagged commands per device */ 1837 ushort start_motor; /* start motor command allowed */ 1838 uchar scsi_reset_wait; /* delay in seconds after scsi bus reset */ 1839 uchar chip_no; /* should be assigned by caller */ 1840 uchar max_host_qng; /* maximum number of Q'ed command allowed */ 1841 ushort no_scam; /* scam_tolerant of EEPROM */ 1842 struct asc_board *drv_ptr; /* driver pointer to private structure */ 1843 uchar chip_scsi_id; /* chip SCSI target ID */ 1844 uchar chip_type; 1845 uchar bist_err_code; 1846 ADV_CARR_T *carrier; 1847 ADV_CARR_T *carr_freelist; /* Carrier free list. */ 1848 dma_addr_t carrier_addr; 1849 ADV_CARR_T *icq_sp; /* Initiator command queue stopper pointer. */ 1850 ADV_CARR_T *irq_sp; /* Initiator response queue stopper pointer. */ 1851 ushort carr_pending_cnt; /* Count of pending carriers. */ 1852 /* 1853 * Note: The following fields will not be used after initialization. The 1854 * driver may discard the buffer after initialization is done. 1855 */ 1856 ADV_DVC_CFG *cfg; /* temporary configuration structure */ 1857 } ADV_DVC_VAR; 1858 1859 /* 1860 * Microcode idle loop commands 1861 */ 1862 #define IDLE_CMD_COMPLETED 0 1863 #define IDLE_CMD_STOP_CHIP 0x0001 1864 #define IDLE_CMD_STOP_CHIP_SEND_INT 0x0002 1865 #define IDLE_CMD_SEND_INT 0x0004 1866 #define IDLE_CMD_ABORT 0x0008 1867 #define IDLE_CMD_DEVICE_RESET 0x0010 1868 #define IDLE_CMD_SCSI_RESET_START 0x0020 /* Assert SCSI Bus Reset */ 1869 #define IDLE_CMD_SCSI_RESET_END 0x0040 /* Deassert SCSI Bus Reset */ 1870 #define IDLE_CMD_SCSIREQ 0x0080 1871 1872 #define IDLE_CMD_STATUS_SUCCESS 0x0001 1873 #define IDLE_CMD_STATUS_FAILURE 0x0002 1874 1875 /* 1876 * AdvSendIdleCmd() flag definitions. 1877 */ 1878 #define ADV_NOWAIT 0x01 1879 1880 /* 1881 * Wait loop time out values. 1882 */ 1883 #define SCSI_WAIT_100_MSEC 100UL /* 100 milliseconds */ 1884 #define SCSI_US_PER_MSEC 1000 /* microseconds per millisecond */ 1885 #define SCSI_MAX_RETRY 10 /* retry count */ 1886 1887 #define ADV_ASYNC_RDMA_FAILURE 0x01 /* Fatal RDMA failure. */ 1888 #define ADV_ASYNC_SCSI_BUS_RESET_DET 0x02 /* Detected SCSI Bus Reset. */ 1889 #define ADV_ASYNC_CARRIER_READY_FAILURE 0x03 /* Carrier Ready failure. */ 1890 #define ADV_RDMA_IN_CARR_AND_Q_INVALID 0x04 /* RDMAed-in data invalid. */ 1891 1892 #define ADV_HOST_SCSI_BUS_RESET 0x80 /* Host Initiated SCSI Bus Reset. */ 1893 1894 /* Read byte from a register. */ 1895 #define AdvReadByteRegister(iop_base, reg_off) \ 1896 (ADV_MEM_READB((iop_base) + (reg_off))) 1897 1898 /* Write byte to a register. */ 1899 #define AdvWriteByteRegister(iop_base, reg_off, byte) \ 1900 (ADV_MEM_WRITEB((iop_base) + (reg_off), (byte))) 1901 1902 /* Read word (2 bytes) from a register. */ 1903 #define AdvReadWordRegister(iop_base, reg_off) \ 1904 (ADV_MEM_READW((iop_base) + (reg_off))) 1905 1906 /* Write word (2 bytes) to a register. */ 1907 #define AdvWriteWordRegister(iop_base, reg_off, word) \ 1908 (ADV_MEM_WRITEW((iop_base) + (reg_off), (word))) 1909 1910 /* Write dword (4 bytes) to a register. */ 1911 #define AdvWriteDWordRegister(iop_base, reg_off, dword) \ 1912 (ADV_MEM_WRITEDW((iop_base) + (reg_off), (dword))) 1913 1914 /* Read byte from LRAM. */ 1915 #define AdvReadByteLram(iop_base, addr, byte) \ 1916 do { \ 1917 ADV_MEM_WRITEW((iop_base) + IOPW_RAM_ADDR, (addr)); \ 1918 (byte) = ADV_MEM_READB((iop_base) + IOPB_RAM_DATA); \ 1919 } while (0) 1920 1921 /* Write byte to LRAM. */ 1922 #define AdvWriteByteLram(iop_base, addr, byte) \ 1923 (ADV_MEM_WRITEW((iop_base) + IOPW_RAM_ADDR, (addr)), \ 1924 ADV_MEM_WRITEB((iop_base) + IOPB_RAM_DATA, (byte))) 1925 1926 /* Read word (2 bytes) from LRAM. */ 1927 #define AdvReadWordLram(iop_base, addr, word) \ 1928 do { \ 1929 ADV_MEM_WRITEW((iop_base) + IOPW_RAM_ADDR, (addr)); \ 1930 (word) = (ADV_MEM_READW((iop_base) + IOPW_RAM_DATA)); \ 1931 } while (0) 1932 1933 /* Write word (2 bytes) to LRAM. */ 1934 #define AdvWriteWordLram(iop_base, addr, word) \ 1935 (ADV_MEM_WRITEW((iop_base) + IOPW_RAM_ADDR, (addr)), \ 1936 ADV_MEM_WRITEW((iop_base) + IOPW_RAM_DATA, (word))) 1937 1938 /* Write little-endian double word (4 bytes) to LRAM */ 1939 /* Because of unspecified C language ordering don't use auto-increment. */ 1940 #define AdvWriteDWordLramNoSwap(iop_base, addr, dword) \ 1941 ((ADV_MEM_WRITEW((iop_base) + IOPW_RAM_ADDR, (addr)), \ 1942 ADV_MEM_WRITEW((iop_base) + IOPW_RAM_DATA, \ 1943 cpu_to_le16((ushort) ((dword) & 0xFFFF)))), \ 1944 (ADV_MEM_WRITEW((iop_base) + IOPW_RAM_ADDR, (addr) + 2), \ 1945 ADV_MEM_WRITEW((iop_base) + IOPW_RAM_DATA, \ 1946 cpu_to_le16((ushort) ((dword >> 16) & 0xFFFF))))) 1947 1948 /* Read word (2 bytes) from LRAM assuming that the address is already set. */ 1949 #define AdvReadWordAutoIncLram(iop_base) \ 1950 (ADV_MEM_READW((iop_base) + IOPW_RAM_DATA)) 1951 1952 /* Write word (2 bytes) to LRAM assuming that the address is already set. */ 1953 #define AdvWriteWordAutoIncLram(iop_base, word) \ 1954 (ADV_MEM_WRITEW((iop_base) + IOPW_RAM_DATA, (word))) 1955 1956 /* 1957 * Define macro to check for Condor signature. 1958 * 1959 * Evaluate to ADV_TRUE if a Condor chip is found the specified port 1960 * address 'iop_base'. Otherwise evalue to ADV_FALSE. 1961 */ 1962 #define AdvFindSignature(iop_base) \ 1963 (((AdvReadByteRegister((iop_base), IOPB_CHIP_ID_1) == \ 1964 ADV_CHIP_ID_BYTE) && \ 1965 (AdvReadWordRegister((iop_base), IOPW_CHIP_ID_0) == \ 1966 ADV_CHIP_ID_WORD)) ? ADV_TRUE : ADV_FALSE) 1967 1968 /* 1969 * Define macro to Return the version number of the chip at 'iop_base'. 1970 * 1971 * The second parameter 'bus_type' is currently unused. 1972 */ 1973 #define AdvGetChipVersion(iop_base, bus_type) \ 1974 AdvReadByteRegister((iop_base), IOPB_CHIP_TYPE_REV) 1975 1976 /* 1977 * Abort an SRB in the chip's RISC Memory. The 'srb_tag' argument must 1978 * match the ADV_SCSI_REQ_Q 'srb_tag' field. 1979 * 1980 * If the request has not yet been sent to the device it will simply be 1981 * aborted from RISC memory. If the request is disconnected it will be 1982 * aborted on reselection by sending an Abort Message to the target ID. 1983 * 1984 * Return value: 1985 * ADV_TRUE(1) - Queue was successfully aborted. 1986 * ADV_FALSE(0) - Queue was not found on the active queue list. 1987 */ 1988 #define AdvAbortQueue(asc_dvc, srb_tag) \ 1989 AdvSendIdleCmd((asc_dvc), (ushort) IDLE_CMD_ABORT, \ 1990 (ADV_DCNT) (srb_tag)) 1991 1992 /* 1993 * Send a Bus Device Reset Message to the specified target ID. 1994 * 1995 * All outstanding commands will be purged if sending the 1996 * Bus Device Reset Message is successful. 1997 * 1998 * Return Value: 1999 * ADV_TRUE(1) - All requests on the target are purged. 2000 * ADV_FALSE(0) - Couldn't issue Bus Device Reset Message; Requests 2001 * are not purged. 2002 */ 2003 #define AdvResetDevice(asc_dvc, target_id) \ 2004 AdvSendIdleCmd((asc_dvc), (ushort) IDLE_CMD_DEVICE_RESET, \ 2005 (ADV_DCNT) (target_id)) 2006 2007 /* 2008 * SCSI Wide Type definition. 2009 */ 2010 #define ADV_SCSI_BIT_ID_TYPE ushort 2011 2012 /* 2013 * AdvInitScsiTarget() 'cntl_flag' options. 2014 */ 2015 #define ADV_SCAN_LUN 0x01 2016 #define ADV_CAPINFO_NOLUN 0x02 2017 2018 /* 2019 * Convert target id to target id bit mask. 2020 */ 2021 #define ADV_TID_TO_TIDMASK(tid) (0x01 << ((tid) & ADV_MAX_TID)) 2022 2023 /* 2024 * ADV_SCSI_REQ_Q 'done_status' and 'host_status' return values. 2025 */ 2026 2027 #define QD_NO_STATUS 0x00 /* Request not completed yet. */ 2028 #define QD_NO_ERROR 0x01 2029 #define QD_ABORTED_BY_HOST 0x02 2030 #define QD_WITH_ERROR 0x04 2031 2032 #define QHSTA_NO_ERROR 0x00 2033 #define QHSTA_M_SEL_TIMEOUT 0x11 2034 #define QHSTA_M_DATA_OVER_RUN 0x12 2035 #define QHSTA_M_UNEXPECTED_BUS_FREE 0x13 2036 #define QHSTA_M_QUEUE_ABORTED 0x15 2037 #define QHSTA_M_SXFR_SDMA_ERR 0x16 /* SXFR_STATUS SCSI DMA Error */ 2038 #define QHSTA_M_SXFR_SXFR_PERR 0x17 /* SXFR_STATUS SCSI Bus Parity Error */ 2039 #define QHSTA_M_RDMA_PERR 0x18 /* RISC PCI DMA parity error */ 2040 #define QHSTA_M_SXFR_OFF_UFLW 0x19 /* SXFR_STATUS Offset Underflow */ 2041 #define QHSTA_M_SXFR_OFF_OFLW 0x20 /* SXFR_STATUS Offset Overflow */ 2042 #define QHSTA_M_SXFR_WD_TMO 0x21 /* SXFR_STATUS Watchdog Timeout */ 2043 #define QHSTA_M_SXFR_DESELECTED 0x22 /* SXFR_STATUS Deselected */ 2044 /* Note: QHSTA_M_SXFR_XFR_OFLW is identical to QHSTA_M_DATA_OVER_RUN. */ 2045 #define QHSTA_M_SXFR_XFR_OFLW 0x12 /* SXFR_STATUS Transfer Overflow */ 2046 #define QHSTA_M_SXFR_XFR_PH_ERR 0x24 /* SXFR_STATUS Transfer Phase Error */ 2047 #define QHSTA_M_SXFR_UNKNOWN_ERROR 0x25 /* SXFR_STATUS Unknown Error */ 2048 #define QHSTA_M_SCSI_BUS_RESET 0x30 /* Request aborted from SBR */ 2049 #define QHSTA_M_SCSI_BUS_RESET_UNSOL 0x31 /* Request aborted from unsol. SBR */ 2050 #define QHSTA_M_BUS_DEVICE_RESET 0x32 /* Request aborted from BDR */ 2051 #define QHSTA_M_DIRECTION_ERR 0x35 /* Data Phase mismatch */ 2052 #define QHSTA_M_DIRECTION_ERR_HUNG 0x36 /* Data Phase mismatch and bus hang */ 2053 #define QHSTA_M_WTM_TIMEOUT 0x41 2054 #define QHSTA_M_BAD_CMPL_STATUS_IN 0x42 2055 #define QHSTA_M_NO_AUTO_REQ_SENSE 0x43 2056 #define QHSTA_M_AUTO_REQ_SENSE_FAIL 0x44 2057 #define QHSTA_M_INVALID_DEVICE 0x45 /* Bad target ID */ 2058 #define QHSTA_M_FROZEN_TIDQ 0x46 /* TID Queue frozen. */ 2059 #define QHSTA_M_SGBACKUP_ERROR 0x47 /* Scatter-Gather backup error */ 2060 2061 /* Return the address that is aligned at the next doubleword >= to 'addr'. */ 2062 #define ADV_32BALIGN(addr) (((ulong) (addr) + 0x1F) & ~0x1F) 2063 2064 /* 2065 * Total contiguous memory needed for driver SG blocks. 2066 * 2067 * ADV_MAX_SG_LIST must be defined by a driver. It is the maximum 2068 * number of scatter-gather elements the driver supports in a 2069 * single request. 2070 */ 2071 2072 #define ADV_SG_LIST_MAX_BYTE_SIZE \ 2073 (sizeof(ADV_SG_BLOCK) * \ 2074 ((ADV_MAX_SG_LIST + (NO_OF_SG_PER_BLOCK - 1))/NO_OF_SG_PER_BLOCK)) 2075 2076 /* struct asc_board flags */ 2077 #define ASC_IS_WIDE_BOARD 0x04 /* AdvanSys Wide Board */ 2078 2079 #define ASC_NARROW_BOARD(boardp) (((boardp)->flags & ASC_IS_WIDE_BOARD) == 0) 2080 2081 #define NO_ISA_DMA 0xff /* No ISA DMA Channel Used */ 2082 2083 #define ASC_INFO_SIZE 128 /* advansys_info() line size */ 2084 2085 /* Asc Library return codes */ 2086 #define ASC_TRUE 1 2087 #define ASC_FALSE 0 2088 #define ASC_NOERROR 1 2089 #define ASC_BUSY 0 2090 #define ASC_ERROR (-1) 2091 2092 /* struct scsi_cmnd function return codes */ 2093 #define STATUS_BYTE(byte) (byte) 2094 #define MSG_BYTE(byte) ((byte) << 8) 2095 #define HOST_BYTE(byte) ((byte) << 16) 2096 #define DRIVER_BYTE(byte) ((byte) << 24) 2097 2098 #define ASC_STATS(shost, counter) ASC_STATS_ADD(shost, counter, 1) 2099 #ifndef ADVANSYS_STATS 2100 #define ASC_STATS_ADD(shost, counter, count) 2101 #else /* ADVANSYS_STATS */ 2102 #define ASC_STATS_ADD(shost, counter, count) \ 2103 (((struct asc_board *) shost_priv(shost))->asc_stats.counter += (count)) 2104 #endif /* ADVANSYS_STATS */ 2105 2106 /* If the result wraps when calculating tenths, return 0. */ 2107 #define ASC_TENTHS(num, den) \ 2108 (((10 * ((num)/(den))) > (((num) * 10)/(den))) ? \ 2109 0 : ((((num) * 10)/(den)) - (10 * ((num)/(den))))) 2110 2111 /* 2112 * Display a message to the console. 2113 */ 2114 #define ASC_PRINT(s) \ 2115 { \ 2116 printk("advansys: "); \ 2117 printk(s); \ 2118 } 2119 2120 #define ASC_PRINT1(s, a1) \ 2121 { \ 2122 printk("advansys: "); \ 2123 printk((s), (a1)); \ 2124 } 2125 2126 #define ASC_PRINT2(s, a1, a2) \ 2127 { \ 2128 printk("advansys: "); \ 2129 printk((s), (a1), (a2)); \ 2130 } 2131 2132 #define ASC_PRINT3(s, a1, a2, a3) \ 2133 { \ 2134 printk("advansys: "); \ 2135 printk((s), (a1), (a2), (a3)); \ 2136 } 2137 2138 #define ASC_PRINT4(s, a1, a2, a3, a4) \ 2139 { \ 2140 printk("advansys: "); \ 2141 printk((s), (a1), (a2), (a3), (a4)); \ 2142 } 2143 2144 #ifndef ADVANSYS_DEBUG 2145 2146 #define ASC_DBG(lvl, s...) 2147 #define ASC_DBG_PRT_SCSI_HOST(lvl, s) 2148 #define ASC_DBG_PRT_ASC_SCSI_Q(lvl, scsiqp) 2149 #define ASC_DBG_PRT_ADV_SCSI_REQ_Q(lvl, scsiqp) 2150 #define ASC_DBG_PRT_ASC_QDONE_INFO(lvl, qdone) 2151 #define ADV_DBG_PRT_ADV_SCSI_REQ_Q(lvl, scsiqp) 2152 #define ASC_DBG_PRT_HEX(lvl, name, start, length) 2153 #define ASC_DBG_PRT_CDB(lvl, cdb, len) 2154 #define ASC_DBG_PRT_SENSE(lvl, sense, len) 2155 #define ASC_DBG_PRT_INQUIRY(lvl, inq, len) 2156 2157 #else /* ADVANSYS_DEBUG */ 2158 2159 /* 2160 * Debugging Message Levels: 2161 * 0: Errors Only 2162 * 1: High-Level Tracing 2163 * 2-N: Verbose Tracing 2164 */ 2165 2166 #define ASC_DBG(lvl, format, arg...) { \ 2167 if (asc_dbglvl >= (lvl)) \ 2168 printk(KERN_DEBUG "%s: %s: " format, DRV_NAME, \ 2169 __func__ , ## arg); \ 2170 } 2171 2172 #define ASC_DBG_PRT_SCSI_HOST(lvl, s) \ 2173 { \ 2174 if (asc_dbglvl >= (lvl)) { \ 2175 asc_prt_scsi_host(s); \ 2176 } \ 2177 } 2178 2179 #define ASC_DBG_PRT_ASC_SCSI_Q(lvl, scsiqp) \ 2180 { \ 2181 if (asc_dbglvl >= (lvl)) { \ 2182 asc_prt_asc_scsi_q(scsiqp); \ 2183 } \ 2184 } 2185 2186 #define ASC_DBG_PRT_ASC_QDONE_INFO(lvl, qdone) \ 2187 { \ 2188 if (asc_dbglvl >= (lvl)) { \ 2189 asc_prt_asc_qdone_info(qdone); \ 2190 } \ 2191 } 2192 2193 #define ASC_DBG_PRT_ADV_SCSI_REQ_Q(lvl, scsiqp) \ 2194 { \ 2195 if (asc_dbglvl >= (lvl)) { \ 2196 asc_prt_adv_scsi_req_q(scsiqp); \ 2197 } \ 2198 } 2199 2200 #define ASC_DBG_PRT_HEX(lvl, name, start, length) \ 2201 { \ 2202 if (asc_dbglvl >= (lvl)) { \ 2203 asc_prt_hex((name), (start), (length)); \ 2204 } \ 2205 } 2206 2207 #define ASC_DBG_PRT_CDB(lvl, cdb, len) \ 2208 ASC_DBG_PRT_HEX((lvl), "CDB", (uchar *) (cdb), (len)); 2209 2210 #define ASC_DBG_PRT_SENSE(lvl, sense, len) \ 2211 ASC_DBG_PRT_HEX((lvl), "SENSE", (uchar *) (sense), (len)); 2212 2213 #define ASC_DBG_PRT_INQUIRY(lvl, inq, len) \ 2214 ASC_DBG_PRT_HEX((lvl), "INQUIRY", (uchar *) (inq), (len)); 2215 #endif /* ADVANSYS_DEBUG */ 2216 2217 #ifdef ADVANSYS_STATS 2218 2219 /* Per board statistics structure */ 2220 struct asc_stats { 2221 /* Driver Entrypoint Statistics */ 2222 unsigned int queuecommand; /* # calls to advansys_queuecommand() */ 2223 unsigned int reset; /* # calls to advansys_eh_bus_reset() */ 2224 unsigned int biosparam; /* # calls to advansys_biosparam() */ 2225 unsigned int interrupt; /* # advansys_interrupt() calls */ 2226 unsigned int callback; /* # calls to asc/adv_isr_callback() */ 2227 unsigned int done; /* # calls to request's scsi_done function */ 2228 unsigned int build_error; /* # asc/adv_build_req() ASC_ERROR returns. */ 2229 unsigned int adv_build_noreq; /* # adv_build_req() adv_req_t alloc. fail. */ 2230 unsigned int adv_build_nosg; /* # adv_build_req() adv_sgblk_t alloc. fail. */ 2231 /* AscExeScsiQueue()/AdvExeScsiQueue() Statistics */ 2232 unsigned int exe_noerror; /* # ASC_NOERROR returns. */ 2233 unsigned int exe_busy; /* # ASC_BUSY returns. */ 2234 unsigned int exe_error; /* # ASC_ERROR returns. */ 2235 unsigned int exe_unknown; /* # unknown returns. */ 2236 /* Data Transfer Statistics */ 2237 unsigned int xfer_cnt; /* # I/O requests received */ 2238 unsigned int xfer_elem; /* # scatter-gather elements */ 2239 unsigned int xfer_sect; /* # 512-byte blocks */ 2240 }; 2241 #endif /* ADVANSYS_STATS */ 2242 2243 /* 2244 * Structure allocated for each board. 2245 * 2246 * This structure is allocated by scsi_host_alloc() at the end 2247 * of the 'Scsi_Host' structure starting at the 'hostdata' 2248 * field. It is guaranteed to be allocated from DMA-able memory. 2249 */ 2250 struct asc_board { 2251 struct device *dev; 2252 struct Scsi_Host *shost; 2253 uint flags; /* Board flags */ 2254 unsigned int irq; 2255 union { 2256 ASC_DVC_VAR asc_dvc_var; /* Narrow board */ 2257 ADV_DVC_VAR adv_dvc_var; /* Wide board */ 2258 } dvc_var; 2259 union { 2260 ASC_DVC_CFG asc_dvc_cfg; /* Narrow board */ 2261 ADV_DVC_CFG adv_dvc_cfg; /* Wide board */ 2262 } dvc_cfg; 2263 ushort asc_n_io_port; /* Number I/O ports. */ 2264 ADV_SCSI_BIT_ID_TYPE init_tidmask; /* Target init./valid mask */ 2265 ushort reqcnt[ADV_MAX_TID + 1]; /* Starvation request count */ 2266 ADV_SCSI_BIT_ID_TYPE queue_full; /* Queue full mask */ 2267 ushort queue_full_cnt[ADV_MAX_TID + 1]; /* Queue full count */ 2268 union { 2269 ASCEEP_CONFIG asc_eep; /* Narrow EEPROM config. */ 2270 ADVEEP_3550_CONFIG adv_3550_eep; /* 3550 EEPROM config. */ 2271 ADVEEP_38C0800_CONFIG adv_38C0800_eep; /* 38C0800 EEPROM config. */ 2272 ADVEEP_38C1600_CONFIG adv_38C1600_eep; /* 38C1600 EEPROM config. */ 2273 } eep_config; 2274 /* /proc/scsi/advansys/[0...] */ 2275 #ifdef ADVANSYS_STATS 2276 struct asc_stats asc_stats; /* Board statistics */ 2277 #endif /* ADVANSYS_STATS */ 2278 /* 2279 * The following fields are used only for Narrow Boards. 2280 */ 2281 uchar sdtr_data[ASC_MAX_TID + 1]; /* SDTR information */ 2282 /* 2283 * The following fields are used only for Wide Boards. 2284 */ 2285 void __iomem *ioremap_addr; /* I/O Memory remap address. */ 2286 ushort ioport; /* I/O Port address. */ 2287 adv_req_t *adv_reqp; /* Request structures. */ 2288 dma_addr_t adv_reqp_addr; 2289 size_t adv_reqp_size; 2290 struct dma_pool *adv_sgblk_pool; /* Scatter-gather structures. */ 2291 ushort bios_signature; /* BIOS Signature. */ 2292 ushort bios_version; /* BIOS Version. */ 2293 ushort bios_codeseg; /* BIOS Code Segment. */ 2294 ushort bios_codelen; /* BIOS Code Segment Length. */ 2295 }; 2296 2297 #define asc_dvc_to_board(asc_dvc) container_of(asc_dvc, struct asc_board, \ 2298 dvc_var.asc_dvc_var) 2299 #define adv_dvc_to_board(adv_dvc) container_of(adv_dvc, struct asc_board, \ 2300 dvc_var.adv_dvc_var) 2301 #define adv_dvc_to_pdev(adv_dvc) to_pci_dev(adv_dvc_to_board(adv_dvc)->dev) 2302 2303 #ifdef ADVANSYS_DEBUG 2304 static int asc_dbglvl = 3; 2305 2306 /* 2307 * asc_prt_asc_dvc_var() 2308 */ 2309 static void asc_prt_asc_dvc_var(ASC_DVC_VAR *h) 2310 { 2311 printk("ASC_DVC_VAR at addr 0x%lx\n", (ulong)h); 2312 2313 printk(" iop_base 0x%x, err_code 0x%x, dvc_cntl 0x%x, bug_fix_cntl " 2314 "%d,\n", h->iop_base, h->err_code, h->dvc_cntl, h->bug_fix_cntl); 2315 2316 printk(" bus_type %d, init_sdtr 0x%x,\n", h->bus_type, 2317 (unsigned)h->init_sdtr); 2318 2319 printk(" sdtr_done 0x%x, use_tagged_qng 0x%x, unit_not_ready 0x%x, " 2320 "chip_no 0x%x,\n", (unsigned)h->sdtr_done, 2321 (unsigned)h->use_tagged_qng, (unsigned)h->unit_not_ready, 2322 (unsigned)h->chip_no); 2323 2324 printk(" queue_full_or_busy 0x%x, start_motor 0x%x, scsi_reset_wait " 2325 "%u,\n", (unsigned)h->queue_full_or_busy, 2326 (unsigned)h->start_motor, (unsigned)h->scsi_reset_wait); 2327 2328 printk(" is_in_int %u, max_total_qng %u, cur_total_qng %u, " 2329 "in_critical_cnt %u,\n", (unsigned)h->is_in_int, 2330 (unsigned)h->max_total_qng, (unsigned)h->cur_total_qng, 2331 (unsigned)h->in_critical_cnt); 2332 2333 printk(" last_q_shortage %u, init_state 0x%x, no_scam 0x%x, " 2334 "pci_fix_asyn_xfer 0x%x,\n", (unsigned)h->last_q_shortage, 2335 (unsigned)h->init_state, (unsigned)h->no_scam, 2336 (unsigned)h->pci_fix_asyn_xfer); 2337 2338 printk(" cfg 0x%lx\n", (ulong)h->cfg); 2339 } 2340 2341 /* 2342 * asc_prt_asc_dvc_cfg() 2343 */ 2344 static void asc_prt_asc_dvc_cfg(ASC_DVC_CFG *h) 2345 { 2346 printk("ASC_DVC_CFG at addr 0x%lx\n", (ulong)h); 2347 2348 printk(" can_tagged_qng 0x%x, cmd_qng_enabled 0x%x,\n", 2349 h->can_tagged_qng, h->cmd_qng_enabled); 2350 printk(" disc_enable 0x%x, sdtr_enable 0x%x,\n", 2351 h->disc_enable, h->sdtr_enable); 2352 2353 printk(" chip_scsi_id %d, isa_dma_speed %d, isa_dma_channel %d, " 2354 "chip_version %d,\n", h->chip_scsi_id, h->isa_dma_speed, 2355 h->isa_dma_channel, h->chip_version); 2356 2357 printk(" mcode_date 0x%x, mcode_version %d\n", 2358 h->mcode_date, h->mcode_version); 2359 } 2360 2361 /* 2362 * asc_prt_adv_dvc_var() 2363 * 2364 * Display an ADV_DVC_VAR structure. 2365 */ 2366 static void asc_prt_adv_dvc_var(ADV_DVC_VAR *h) 2367 { 2368 printk(" ADV_DVC_VAR at addr 0x%lx\n", (ulong)h); 2369 2370 printk(" iop_base 0x%lx, err_code 0x%x, ultra_able 0x%x\n", 2371 (ulong)h->iop_base, h->err_code, (unsigned)h->ultra_able); 2372 2373 printk(" sdtr_able 0x%x, wdtr_able 0x%x\n", 2374 (unsigned)h->sdtr_able, (unsigned)h->wdtr_able); 2375 2376 printk(" start_motor 0x%x, scsi_reset_wait 0x%x\n", 2377 (unsigned)h->start_motor, (unsigned)h->scsi_reset_wait); 2378 2379 printk(" max_host_qng %u, max_dvc_qng %u, carr_freelist 0x%p\n", 2380 (unsigned)h->max_host_qng, (unsigned)h->max_dvc_qng, 2381 h->carr_freelist); 2382 2383 printk(" icq_sp 0x%p, irq_sp 0x%p\n", h->icq_sp, h->irq_sp); 2384 2385 printk(" no_scam 0x%x, tagqng_able 0x%x\n", 2386 (unsigned)h->no_scam, (unsigned)h->tagqng_able); 2387 2388 printk(" chip_scsi_id 0x%x, cfg 0x%lx\n", 2389 (unsigned)h->chip_scsi_id, (ulong)h->cfg); 2390 } 2391 2392 /* 2393 * asc_prt_adv_dvc_cfg() 2394 * 2395 * Display an ADV_DVC_CFG structure. 2396 */ 2397 static void asc_prt_adv_dvc_cfg(ADV_DVC_CFG *h) 2398 { 2399 printk(" ADV_DVC_CFG at addr 0x%lx\n", (ulong)h); 2400 2401 printk(" disc_enable 0x%x, termination 0x%x\n", 2402 h->disc_enable, h->termination); 2403 2404 printk(" chip_version 0x%x, mcode_date 0x%x\n", 2405 h->chip_version, h->mcode_date); 2406 2407 printk(" mcode_version 0x%x, control_flag 0x%x\n", 2408 h->mcode_version, h->control_flag); 2409 } 2410 2411 /* 2412 * asc_prt_scsi_host() 2413 */ 2414 static void asc_prt_scsi_host(struct Scsi_Host *s) 2415 { 2416 struct asc_board *boardp = shost_priv(s); 2417 2418 printk("Scsi_Host at addr 0x%p, device %s\n", s, dev_name(boardp->dev)); 2419 printk(" host_busy %d, host_no %d,\n", 2420 scsi_host_busy(s), s->host_no); 2421 2422 printk(" base 0x%lx, io_port 0x%lx, irq %d,\n", 2423 (ulong)s->base, (ulong)s->io_port, boardp->irq); 2424 2425 printk(" dma_channel %d, this_id %d, can_queue %d,\n", 2426 s->dma_channel, s->this_id, s->can_queue); 2427 2428 printk(" cmd_per_lun %d, sg_tablesize %d, unchecked_isa_dma %d\n", 2429 s->cmd_per_lun, s->sg_tablesize, s->unchecked_isa_dma); 2430 2431 if (ASC_NARROW_BOARD(boardp)) { 2432 asc_prt_asc_dvc_var(&boardp->dvc_var.asc_dvc_var); 2433 asc_prt_asc_dvc_cfg(&boardp->dvc_cfg.asc_dvc_cfg); 2434 } else { 2435 asc_prt_adv_dvc_var(&boardp->dvc_var.adv_dvc_var); 2436 asc_prt_adv_dvc_cfg(&boardp->dvc_cfg.adv_dvc_cfg); 2437 } 2438 } 2439 2440 /* 2441 * asc_prt_hex() 2442 * 2443 * Print hexadecimal output in 4 byte groupings 32 bytes 2444 * or 8 double-words per line. 2445 */ 2446 static void asc_prt_hex(char *f, uchar *s, int l) 2447 { 2448 int i; 2449 int j; 2450 int k; 2451 int m; 2452 2453 printk("%s: (%d bytes)\n", f, l); 2454 2455 for (i = 0; i < l; i += 32) { 2456 2457 /* Display a maximum of 8 double-words per line. */ 2458 if ((k = (l - i) / 4) >= 8) { 2459 k = 8; 2460 m = 0; 2461 } else { 2462 m = (l - i) % 4; 2463 } 2464 2465 for (j = 0; j < k; j++) { 2466 printk(" %2.2X%2.2X%2.2X%2.2X", 2467 (unsigned)s[i + (j * 4)], 2468 (unsigned)s[i + (j * 4) + 1], 2469 (unsigned)s[i + (j * 4) + 2], 2470 (unsigned)s[i + (j * 4) + 3]); 2471 } 2472 2473 switch (m) { 2474 case 0: 2475 default: 2476 break; 2477 case 1: 2478 printk(" %2.2X", (unsigned)s[i + (j * 4)]); 2479 break; 2480 case 2: 2481 printk(" %2.2X%2.2X", 2482 (unsigned)s[i + (j * 4)], 2483 (unsigned)s[i + (j * 4) + 1]); 2484 break; 2485 case 3: 2486 printk(" %2.2X%2.2X%2.2X", 2487 (unsigned)s[i + (j * 4) + 1], 2488 (unsigned)s[i + (j * 4) + 2], 2489 (unsigned)s[i + (j * 4) + 3]); 2490 break; 2491 } 2492 2493 printk("\n"); 2494 } 2495 } 2496 2497 /* 2498 * asc_prt_asc_scsi_q() 2499 */ 2500 static void asc_prt_asc_scsi_q(ASC_SCSI_Q *q) 2501 { 2502 ASC_SG_HEAD *sgp; 2503 int i; 2504 2505 printk("ASC_SCSI_Q at addr 0x%lx\n", (ulong)q); 2506 2507 printk 2508 (" target_ix 0x%x, target_lun %u, srb_tag 0x%x, tag_code 0x%x,\n", 2509 q->q2.target_ix, q->q1.target_lun, q->q2.srb_tag, 2510 q->q2.tag_code); 2511 2512 printk 2513 (" data_addr 0x%lx, data_cnt %lu, sense_addr 0x%lx, sense_len %u,\n", 2514 (ulong)le32_to_cpu(q->q1.data_addr), 2515 (ulong)le32_to_cpu(q->q1.data_cnt), 2516 (ulong)le32_to_cpu(q->q1.sense_addr), q->q1.sense_len); 2517 2518 printk(" cdbptr 0x%lx, cdb_len %u, sg_head 0x%lx, sg_queue_cnt %u\n", 2519 (ulong)q->cdbptr, q->q2.cdb_len, 2520 (ulong)q->sg_head, q->q1.sg_queue_cnt); 2521 2522 if (q->sg_head) { 2523 sgp = q->sg_head; 2524 printk("ASC_SG_HEAD at addr 0x%lx\n", (ulong)sgp); 2525 printk(" entry_cnt %u, queue_cnt %u\n", sgp->entry_cnt, 2526 sgp->queue_cnt); 2527 for (i = 0; i < sgp->entry_cnt; i++) { 2528 printk(" [%u]: addr 0x%lx, bytes %lu\n", 2529 i, (ulong)le32_to_cpu(sgp->sg_list[i].addr), 2530 (ulong)le32_to_cpu(sgp->sg_list[i].bytes)); 2531 } 2532 2533 } 2534 } 2535 2536 /* 2537 * asc_prt_asc_qdone_info() 2538 */ 2539 static void asc_prt_asc_qdone_info(ASC_QDONE_INFO *q) 2540 { 2541 printk("ASC_QDONE_INFO at addr 0x%lx\n", (ulong)q); 2542 printk(" srb_tag 0x%x, target_ix %u, cdb_len %u, tag_code %u,\n", 2543 q->d2.srb_tag, q->d2.target_ix, q->d2.cdb_len, 2544 q->d2.tag_code); 2545 printk 2546 (" done_stat 0x%x, host_stat 0x%x, scsi_stat 0x%x, scsi_msg 0x%x\n", 2547 q->d3.done_stat, q->d3.host_stat, q->d3.scsi_stat, q->d3.scsi_msg); 2548 } 2549 2550 /* 2551 * asc_prt_adv_sgblock() 2552 * 2553 * Display an ADV_SG_BLOCK structure. 2554 */ 2555 static void asc_prt_adv_sgblock(int sgblockno, ADV_SG_BLOCK *b) 2556 { 2557 int i; 2558 2559 printk(" ADV_SG_BLOCK at addr 0x%lx (sgblockno %d)\n", 2560 (ulong)b, sgblockno); 2561 printk(" sg_cnt %u, sg_ptr 0x%x\n", 2562 b->sg_cnt, (u32)le32_to_cpu(b->sg_ptr)); 2563 BUG_ON(b->sg_cnt > NO_OF_SG_PER_BLOCK); 2564 if (b->sg_ptr != 0) 2565 BUG_ON(b->sg_cnt != NO_OF_SG_PER_BLOCK); 2566 for (i = 0; i < b->sg_cnt; i++) { 2567 printk(" [%u]: sg_addr 0x%x, sg_count 0x%x\n", 2568 i, (u32)le32_to_cpu(b->sg_list[i].sg_addr), 2569 (u32)le32_to_cpu(b->sg_list[i].sg_count)); 2570 } 2571 } 2572 2573 /* 2574 * asc_prt_adv_scsi_req_q() 2575 * 2576 * Display an ADV_SCSI_REQ_Q structure. 2577 */ 2578 static void asc_prt_adv_scsi_req_q(ADV_SCSI_REQ_Q *q) 2579 { 2580 int sg_blk_cnt; 2581 struct adv_sg_block *sg_ptr; 2582 adv_sgblk_t *sgblkp; 2583 2584 printk("ADV_SCSI_REQ_Q at addr 0x%lx\n", (ulong)q); 2585 2586 printk(" target_id %u, target_lun %u, srb_tag 0x%x\n", 2587 q->target_id, q->target_lun, q->srb_tag); 2588 2589 printk(" cntl 0x%x, data_addr 0x%lx\n", 2590 q->cntl, (ulong)le32_to_cpu(q->data_addr)); 2591 2592 printk(" data_cnt %lu, sense_addr 0x%lx, sense_len %u,\n", 2593 (ulong)le32_to_cpu(q->data_cnt), 2594 (ulong)le32_to_cpu(q->sense_addr), q->sense_len); 2595 2596 printk 2597 (" cdb_len %u, done_status 0x%x, host_status 0x%x, scsi_status 0x%x\n", 2598 q->cdb_len, q->done_status, q->host_status, q->scsi_status); 2599 2600 printk(" sg_working_ix 0x%x, target_cmd %u\n", 2601 q->sg_working_ix, q->target_cmd); 2602 2603 printk(" scsiq_rptr 0x%lx, sg_real_addr 0x%lx, sg_list_ptr 0x%lx\n", 2604 (ulong)le32_to_cpu(q->scsiq_rptr), 2605 (ulong)le32_to_cpu(q->sg_real_addr), (ulong)q->sg_list_ptr); 2606 2607 /* Display the request's ADV_SG_BLOCK structures. */ 2608 if (q->sg_list_ptr != NULL) { 2609 sgblkp = container_of(q->sg_list_ptr, adv_sgblk_t, sg_block); 2610 sg_blk_cnt = 0; 2611 while (sgblkp) { 2612 sg_ptr = &sgblkp->sg_block; 2613 asc_prt_adv_sgblock(sg_blk_cnt, sg_ptr); 2614 if (sg_ptr->sg_ptr == 0) { 2615 break; 2616 } 2617 sgblkp = sgblkp->next_sgblkp; 2618 sg_blk_cnt++; 2619 } 2620 } 2621 } 2622 #endif /* ADVANSYS_DEBUG */ 2623 2624 /* 2625 * advansys_info() 2626 * 2627 * Return suitable for printing on the console with the argument 2628 * adapter's configuration information. 2629 * 2630 * Note: The information line should not exceed ASC_INFO_SIZE bytes, 2631 * otherwise the static 'info' array will be overrun. 2632 */ 2633 static const char *advansys_info(struct Scsi_Host *shost) 2634 { 2635 static char info[ASC_INFO_SIZE]; 2636 struct asc_board *boardp = shost_priv(shost); 2637 ASC_DVC_VAR *asc_dvc_varp; 2638 ADV_DVC_VAR *adv_dvc_varp; 2639 char *busname; 2640 char *widename = NULL; 2641 2642 if (ASC_NARROW_BOARD(boardp)) { 2643 asc_dvc_varp = &boardp->dvc_var.asc_dvc_var; 2644 ASC_DBG(1, "begin\n"); 2645 if (asc_dvc_varp->bus_type & ASC_IS_ISA) { 2646 if ((asc_dvc_varp->bus_type & ASC_IS_ISAPNP) == 2647 ASC_IS_ISAPNP) { 2648 busname = "ISA PnP"; 2649 } else { 2650 busname = "ISA"; 2651 } 2652 sprintf(info, 2653 "AdvanSys SCSI %s: %s: IO 0x%lX-0x%lX, IRQ 0x%X, DMA 0x%X", 2654 ASC_VERSION, busname, 2655 (ulong)shost->io_port, 2656 (ulong)shost->io_port + ASC_IOADR_GAP - 1, 2657 boardp->irq, shost->dma_channel); 2658 } else { 2659 if (asc_dvc_varp->bus_type & ASC_IS_VL) { 2660 busname = "VL"; 2661 } else if (asc_dvc_varp->bus_type & ASC_IS_EISA) { 2662 busname = "EISA"; 2663 } else if (asc_dvc_varp->bus_type & ASC_IS_PCI) { 2664 if ((asc_dvc_varp->bus_type & ASC_IS_PCI_ULTRA) 2665 == ASC_IS_PCI_ULTRA) { 2666 busname = "PCI Ultra"; 2667 } else { 2668 busname = "PCI"; 2669 } 2670 } else { 2671 busname = "?"; 2672 shost_printk(KERN_ERR, shost, "unknown bus " 2673 "type %d\n", asc_dvc_varp->bus_type); 2674 } 2675 sprintf(info, 2676 "AdvanSys SCSI %s: %s: IO 0x%lX-0x%lX, IRQ 0x%X", 2677 ASC_VERSION, busname, (ulong)shost->io_port, 2678 (ulong)shost->io_port + ASC_IOADR_GAP - 1, 2679 boardp->irq); 2680 } 2681 } else { 2682 /* 2683 * Wide Adapter Information 2684 * 2685 * Memory-mapped I/O is used instead of I/O space to access 2686 * the adapter, but display the I/O Port range. The Memory 2687 * I/O address is displayed through the driver /proc file. 2688 */ 2689 adv_dvc_varp = &boardp->dvc_var.adv_dvc_var; 2690 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC3550) { 2691 widename = "Ultra-Wide"; 2692 } else if (adv_dvc_varp->chip_type == ADV_CHIP_ASC38C0800) { 2693 widename = "Ultra2-Wide"; 2694 } else { 2695 widename = "Ultra3-Wide"; 2696 } 2697 sprintf(info, 2698 "AdvanSys SCSI %s: PCI %s: PCIMEM 0x%lX-0x%lX, IRQ 0x%X", 2699 ASC_VERSION, widename, (ulong)adv_dvc_varp->iop_base, 2700 (ulong)adv_dvc_varp->iop_base + boardp->asc_n_io_port - 1, boardp->irq); 2701 } 2702 BUG_ON(strlen(info) >= ASC_INFO_SIZE); 2703 ASC_DBG(1, "end\n"); 2704 return info; 2705 } 2706 2707 #ifdef CONFIG_PROC_FS 2708 2709 /* 2710 * asc_prt_board_devices() 2711 * 2712 * Print driver information for devices attached to the board. 2713 */ 2714 static void asc_prt_board_devices(struct seq_file *m, struct Scsi_Host *shost) 2715 { 2716 struct asc_board *boardp = shost_priv(shost); 2717 int chip_scsi_id; 2718 int i; 2719 2720 seq_printf(m, 2721 "\nDevice Information for AdvanSys SCSI Host %d:\n", 2722 shost->host_no); 2723 2724 if (ASC_NARROW_BOARD(boardp)) { 2725 chip_scsi_id = boardp->dvc_cfg.asc_dvc_cfg.chip_scsi_id; 2726 } else { 2727 chip_scsi_id = boardp->dvc_var.adv_dvc_var.chip_scsi_id; 2728 } 2729 2730 seq_puts(m, "Target IDs Detected:"); 2731 for (i = 0; i <= ADV_MAX_TID; i++) { 2732 if (boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) 2733 seq_printf(m, " %X,", i); 2734 } 2735 seq_printf(m, " (%X=Host Adapter)\n", chip_scsi_id); 2736 } 2737 2738 /* 2739 * Display Wide Board BIOS Information. 2740 */ 2741 static void asc_prt_adv_bios(struct seq_file *m, struct Scsi_Host *shost) 2742 { 2743 struct asc_board *boardp = shost_priv(shost); 2744 ushort major, minor, letter; 2745 2746 seq_puts(m, "\nROM BIOS Version: "); 2747 2748 /* 2749 * If the BIOS saved a valid signature, then fill in 2750 * the BIOS code segment base address. 2751 */ 2752 if (boardp->bios_signature != 0x55AA) { 2753 seq_puts(m, "Disabled or Pre-3.1\n" 2754 "BIOS either disabled or Pre-3.1. If it is pre-3.1, then a newer version\n" 2755 "can be found at the ConnectCom FTP site: ftp://ftp.connectcom.net/pub\n"); 2756 } else { 2757 major = (boardp->bios_version >> 12) & 0xF; 2758 minor = (boardp->bios_version >> 8) & 0xF; 2759 letter = (boardp->bios_version & 0xFF); 2760 2761 seq_printf(m, "%d.%d%c\n", 2762 major, minor, 2763 letter >= 26 ? '?' : letter + 'A'); 2764 /* 2765 * Current available ROM BIOS release is 3.1I for UW 2766 * and 3.2I for U2W. This code doesn't differentiate 2767 * UW and U2W boards. 2768 */ 2769 if (major < 3 || (major <= 3 && minor < 1) || 2770 (major <= 3 && minor <= 1 && letter < ('I' - 'A'))) { 2771 seq_puts(m, "Newer version of ROM BIOS is available at the ConnectCom FTP site:\n" 2772 "ftp://ftp.connectcom.net/pub\n"); 2773 } 2774 } 2775 } 2776 2777 /* 2778 * Add serial number to information bar if signature AAh 2779 * is found in at bit 15-9 (7 bits) of word 1. 2780 * 2781 * Serial Number consists fo 12 alpha-numeric digits. 2782 * 2783 * 1 - Product type (A,B,C,D..) Word0: 15-13 (3 bits) 2784 * 2 - MFG Location (A,B,C,D..) Word0: 12-10 (3 bits) 2785 * 3-4 - Product ID (0-99) Word0: 9-0 (10 bits) 2786 * 5 - Product revision (A-J) Word0: " " 2787 * 2788 * Signature Word1: 15-9 (7 bits) 2789 * 6 - Year (0-9) Word1: 8-6 (3 bits) & Word2: 15 (1 bit) 2790 * 7-8 - Week of the year (1-52) Word1: 5-0 (6 bits) 2791 * 2792 * 9-12 - Serial Number (A001-Z999) Word2: 14-0 (15 bits) 2793 * 2794 * Note 1: Only production cards will have a serial number. 2795 * 2796 * Note 2: Signature is most significant 7 bits (0xFE). 2797 * 2798 * Returns ASC_TRUE if serial number found, otherwise returns ASC_FALSE. 2799 */ 2800 static int asc_get_eeprom_string(ushort *serialnum, uchar *cp) 2801 { 2802 ushort w, num; 2803 2804 if ((serialnum[1] & 0xFE00) != ((ushort)0xAA << 8)) { 2805 return ASC_FALSE; 2806 } else { 2807 /* 2808 * First word - 6 digits. 2809 */ 2810 w = serialnum[0]; 2811 2812 /* Product type - 1st digit. */ 2813 if ((*cp = 'A' + ((w & 0xE000) >> 13)) == 'H') { 2814 /* Product type is P=Prototype */ 2815 *cp += 0x8; 2816 } 2817 cp++; 2818 2819 /* Manufacturing location - 2nd digit. */ 2820 *cp++ = 'A' + ((w & 0x1C00) >> 10); 2821 2822 /* Product ID - 3rd, 4th digits. */ 2823 num = w & 0x3FF; 2824 *cp++ = '0' + (num / 100); 2825 num %= 100; 2826 *cp++ = '0' + (num / 10); 2827 2828 /* Product revision - 5th digit. */ 2829 *cp++ = 'A' + (num % 10); 2830 2831 /* 2832 * Second word 2833 */ 2834 w = serialnum[1]; 2835 2836 /* 2837 * Year - 6th digit. 2838 * 2839 * If bit 15 of third word is set, then the 2840 * last digit of the year is greater than 7. 2841 */ 2842 if (serialnum[2] & 0x8000) { 2843 *cp++ = '8' + ((w & 0x1C0) >> 6); 2844 } else { 2845 *cp++ = '0' + ((w & 0x1C0) >> 6); 2846 } 2847 2848 /* Week of year - 7th, 8th digits. */ 2849 num = w & 0x003F; 2850 *cp++ = '0' + num / 10; 2851 num %= 10; 2852 *cp++ = '0' + num; 2853 2854 /* 2855 * Third word 2856 */ 2857 w = serialnum[2] & 0x7FFF; 2858 2859 /* Serial number - 9th digit. */ 2860 *cp++ = 'A' + (w / 1000); 2861 2862 /* 10th, 11th, 12th digits. */ 2863 num = w % 1000; 2864 *cp++ = '0' + num / 100; 2865 num %= 100; 2866 *cp++ = '0' + num / 10; 2867 num %= 10; 2868 *cp++ = '0' + num; 2869 2870 *cp = '\0'; /* Null Terminate the string. */ 2871 return ASC_TRUE; 2872 } 2873 } 2874 2875 /* 2876 * asc_prt_asc_board_eeprom() 2877 * 2878 * Print board EEPROM configuration. 2879 */ 2880 static void asc_prt_asc_board_eeprom(struct seq_file *m, struct Scsi_Host *shost) 2881 { 2882 struct asc_board *boardp = shost_priv(shost); 2883 ASC_DVC_VAR *asc_dvc_varp; 2884 ASCEEP_CONFIG *ep; 2885 int i; 2886 #ifdef CONFIG_ISA 2887 int isa_dma_speed[] = { 10, 8, 7, 6, 5, 4, 3, 2 }; 2888 #endif /* CONFIG_ISA */ 2889 uchar serialstr[13]; 2890 2891 asc_dvc_varp = &boardp->dvc_var.asc_dvc_var; 2892 ep = &boardp->eep_config.asc_eep; 2893 2894 seq_printf(m, 2895 "\nEEPROM Settings for AdvanSys SCSI Host %d:\n", 2896 shost->host_no); 2897 2898 if (asc_get_eeprom_string((ushort *)&ep->adapter_info[0], serialstr) 2899 == ASC_TRUE) 2900 seq_printf(m, " Serial Number: %s\n", serialstr); 2901 else if (ep->adapter_info[5] == 0xBB) 2902 seq_puts(m, 2903 " Default Settings Used for EEPROM-less Adapter.\n"); 2904 else 2905 seq_puts(m, " Serial Number Signature Not Present.\n"); 2906 2907 seq_printf(m, 2908 " Host SCSI ID: %u, Host Queue Size: %u, Device Queue Size: %u\n", 2909 ASC_EEP_GET_CHIP_ID(ep), ep->max_total_qng, 2910 ep->max_tag_qng); 2911 2912 seq_printf(m, 2913 " cntl 0x%x, no_scam 0x%x\n", ep->cntl, ep->no_scam); 2914 2915 seq_puts(m, " Target ID: "); 2916 for (i = 0; i <= ASC_MAX_TID; i++) 2917 seq_printf(m, " %d", i); 2918 2919 seq_puts(m, "\n Disconnects: "); 2920 for (i = 0; i <= ASC_MAX_TID; i++) 2921 seq_printf(m, " %c", 2922 (ep->disc_enable & ADV_TID_TO_TIDMASK(i)) ? 'Y' : 'N'); 2923 2924 seq_puts(m, "\n Command Queuing: "); 2925 for (i = 0; i <= ASC_MAX_TID; i++) 2926 seq_printf(m, " %c", 2927 (ep->use_cmd_qng & ADV_TID_TO_TIDMASK(i)) ? 'Y' : 'N'); 2928 2929 seq_puts(m, "\n Start Motor: "); 2930 for (i = 0; i <= ASC_MAX_TID; i++) 2931 seq_printf(m, " %c", 2932 (ep->start_motor & ADV_TID_TO_TIDMASK(i)) ? 'Y' : 'N'); 2933 2934 seq_puts(m, "\n Synchronous Transfer:"); 2935 for (i = 0; i <= ASC_MAX_TID; i++) 2936 seq_printf(m, " %c", 2937 (ep->init_sdtr & ADV_TID_TO_TIDMASK(i)) ? 'Y' : 'N'); 2938 seq_putc(m, '\n'); 2939 2940 #ifdef CONFIG_ISA 2941 if (asc_dvc_varp->bus_type & ASC_IS_ISA) { 2942 seq_printf(m, 2943 " Host ISA DMA speed: %d MB/S\n", 2944 isa_dma_speed[ASC_EEP_GET_DMA_SPD(ep)]); 2945 } 2946 #endif /* CONFIG_ISA */ 2947 } 2948 2949 /* 2950 * asc_prt_adv_board_eeprom() 2951 * 2952 * Print board EEPROM configuration. 2953 */ 2954 static void asc_prt_adv_board_eeprom(struct seq_file *m, struct Scsi_Host *shost) 2955 { 2956 struct asc_board *boardp = shost_priv(shost); 2957 ADV_DVC_VAR *adv_dvc_varp; 2958 int i; 2959 char *termstr; 2960 uchar serialstr[13]; 2961 ADVEEP_3550_CONFIG *ep_3550 = NULL; 2962 ADVEEP_38C0800_CONFIG *ep_38C0800 = NULL; 2963 ADVEEP_38C1600_CONFIG *ep_38C1600 = NULL; 2964 ushort word; 2965 ushort *wordp; 2966 ushort sdtr_speed = 0; 2967 2968 adv_dvc_varp = &boardp->dvc_var.adv_dvc_var; 2969 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC3550) { 2970 ep_3550 = &boardp->eep_config.adv_3550_eep; 2971 } else if (adv_dvc_varp->chip_type == ADV_CHIP_ASC38C0800) { 2972 ep_38C0800 = &boardp->eep_config.adv_38C0800_eep; 2973 } else { 2974 ep_38C1600 = &boardp->eep_config.adv_38C1600_eep; 2975 } 2976 2977 seq_printf(m, 2978 "\nEEPROM Settings for AdvanSys SCSI Host %d:\n", 2979 shost->host_no); 2980 2981 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC3550) { 2982 wordp = &ep_3550->serial_number_word1; 2983 } else if (adv_dvc_varp->chip_type == ADV_CHIP_ASC38C0800) { 2984 wordp = &ep_38C0800->serial_number_word1; 2985 } else { 2986 wordp = &ep_38C1600->serial_number_word1; 2987 } 2988 2989 if (asc_get_eeprom_string(wordp, serialstr) == ASC_TRUE) 2990 seq_printf(m, " Serial Number: %s\n", serialstr); 2991 else 2992 seq_puts(m, " Serial Number Signature Not Present.\n"); 2993 2994 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC3550) 2995 seq_printf(m, 2996 " Host SCSI ID: %u, Host Queue Size: %u, Device Queue Size: %u\n", 2997 ep_3550->adapter_scsi_id, 2998 ep_3550->max_host_qng, ep_3550->max_dvc_qng); 2999 else if (adv_dvc_varp->chip_type == ADV_CHIP_ASC38C0800) 3000 seq_printf(m, 3001 " Host SCSI ID: %u, Host Queue Size: %u, Device Queue Size: %u\n", 3002 ep_38C0800->adapter_scsi_id, 3003 ep_38C0800->max_host_qng, 3004 ep_38C0800->max_dvc_qng); 3005 else 3006 seq_printf(m, 3007 " Host SCSI ID: %u, Host Queue Size: %u, Device Queue Size: %u\n", 3008 ep_38C1600->adapter_scsi_id, 3009 ep_38C1600->max_host_qng, 3010 ep_38C1600->max_dvc_qng); 3011 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC3550) { 3012 word = ep_3550->termination; 3013 } else if (adv_dvc_varp->chip_type == ADV_CHIP_ASC38C0800) { 3014 word = ep_38C0800->termination_lvd; 3015 } else { 3016 word = ep_38C1600->termination_lvd; 3017 } 3018 switch (word) { 3019 case 1: 3020 termstr = "Low Off/High Off"; 3021 break; 3022 case 2: 3023 termstr = "Low Off/High On"; 3024 break; 3025 case 3: 3026 termstr = "Low On/High On"; 3027 break; 3028 default: 3029 case 0: 3030 termstr = "Automatic"; 3031 break; 3032 } 3033 3034 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC3550) 3035 seq_printf(m, 3036 " termination: %u (%s), bios_ctrl: 0x%x\n", 3037 ep_3550->termination, termstr, 3038 ep_3550->bios_ctrl); 3039 else if (adv_dvc_varp->chip_type == ADV_CHIP_ASC38C0800) 3040 seq_printf(m, 3041 " termination: %u (%s), bios_ctrl: 0x%x\n", 3042 ep_38C0800->termination_lvd, termstr, 3043 ep_38C0800->bios_ctrl); 3044 else 3045 seq_printf(m, 3046 " termination: %u (%s), bios_ctrl: 0x%x\n", 3047 ep_38C1600->termination_lvd, termstr, 3048 ep_38C1600->bios_ctrl); 3049 3050 seq_puts(m, " Target ID: "); 3051 for (i = 0; i <= ADV_MAX_TID; i++) 3052 seq_printf(m, " %X", i); 3053 seq_putc(m, '\n'); 3054 3055 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC3550) { 3056 word = ep_3550->disc_enable; 3057 } else if (adv_dvc_varp->chip_type == ADV_CHIP_ASC38C0800) { 3058 word = ep_38C0800->disc_enable; 3059 } else { 3060 word = ep_38C1600->disc_enable; 3061 } 3062 seq_puts(m, " Disconnects: "); 3063 for (i = 0; i <= ADV_MAX_TID; i++) 3064 seq_printf(m, " %c", 3065 (word & ADV_TID_TO_TIDMASK(i)) ? 'Y' : 'N'); 3066 seq_putc(m, '\n'); 3067 3068 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC3550) { 3069 word = ep_3550->tagqng_able; 3070 } else if (adv_dvc_varp->chip_type == ADV_CHIP_ASC38C0800) { 3071 word = ep_38C0800->tagqng_able; 3072 } else { 3073 word = ep_38C1600->tagqng_able; 3074 } 3075 seq_puts(m, " Command Queuing: "); 3076 for (i = 0; i <= ADV_MAX_TID; i++) 3077 seq_printf(m, " %c", 3078 (word & ADV_TID_TO_TIDMASK(i)) ? 'Y' : 'N'); 3079 seq_putc(m, '\n'); 3080 3081 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC3550) { 3082 word = ep_3550->start_motor; 3083 } else if (adv_dvc_varp->chip_type == ADV_CHIP_ASC38C0800) { 3084 word = ep_38C0800->start_motor; 3085 } else { 3086 word = ep_38C1600->start_motor; 3087 } 3088 seq_puts(m, " Start Motor: "); 3089 for (i = 0; i <= ADV_MAX_TID; i++) 3090 seq_printf(m, " %c", 3091 (word & ADV_TID_TO_TIDMASK(i)) ? 'Y' : 'N'); 3092 seq_putc(m, '\n'); 3093 3094 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC3550) { 3095 seq_puts(m, " Synchronous Transfer:"); 3096 for (i = 0; i <= ADV_MAX_TID; i++) 3097 seq_printf(m, " %c", 3098 (ep_3550->sdtr_able & ADV_TID_TO_TIDMASK(i)) ? 3099 'Y' : 'N'); 3100 seq_putc(m, '\n'); 3101 } 3102 3103 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC3550) { 3104 seq_puts(m, " Ultra Transfer: "); 3105 for (i = 0; i <= ADV_MAX_TID; i++) 3106 seq_printf(m, " %c", 3107 (ep_3550->ultra_able & ADV_TID_TO_TIDMASK(i)) 3108 ? 'Y' : 'N'); 3109 seq_putc(m, '\n'); 3110 } 3111 3112 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC3550) { 3113 word = ep_3550->wdtr_able; 3114 } else if (adv_dvc_varp->chip_type == ADV_CHIP_ASC38C0800) { 3115 word = ep_38C0800->wdtr_able; 3116 } else { 3117 word = ep_38C1600->wdtr_able; 3118 } 3119 seq_puts(m, " Wide Transfer: "); 3120 for (i = 0; i <= ADV_MAX_TID; i++) 3121 seq_printf(m, " %c", 3122 (word & ADV_TID_TO_TIDMASK(i)) ? 'Y' : 'N'); 3123 seq_putc(m, '\n'); 3124 3125 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC38C0800 || 3126 adv_dvc_varp->chip_type == ADV_CHIP_ASC38C1600) { 3127 seq_puts(m, " Synchronous Transfer Speed (Mhz):\n "); 3128 for (i = 0; i <= ADV_MAX_TID; i++) { 3129 char *speed_str; 3130 3131 if (i == 0) { 3132 sdtr_speed = adv_dvc_varp->sdtr_speed1; 3133 } else if (i == 4) { 3134 sdtr_speed = adv_dvc_varp->sdtr_speed2; 3135 } else if (i == 8) { 3136 sdtr_speed = adv_dvc_varp->sdtr_speed3; 3137 } else if (i == 12) { 3138 sdtr_speed = adv_dvc_varp->sdtr_speed4; 3139 } 3140 switch (sdtr_speed & ADV_MAX_TID) { 3141 case 0: 3142 speed_str = "Off"; 3143 break; 3144 case 1: 3145 speed_str = " 5"; 3146 break; 3147 case 2: 3148 speed_str = " 10"; 3149 break; 3150 case 3: 3151 speed_str = " 20"; 3152 break; 3153 case 4: 3154 speed_str = " 40"; 3155 break; 3156 case 5: 3157 speed_str = " 80"; 3158 break; 3159 default: 3160 speed_str = "Unk"; 3161 break; 3162 } 3163 seq_printf(m, "%X:%s ", i, speed_str); 3164 if (i == 7) 3165 seq_puts(m, "\n "); 3166 sdtr_speed >>= 4; 3167 } 3168 seq_putc(m, '\n'); 3169 } 3170 } 3171 3172 /* 3173 * asc_prt_driver_conf() 3174 */ 3175 static void asc_prt_driver_conf(struct seq_file *m, struct Scsi_Host *shost) 3176 { 3177 struct asc_board *boardp = shost_priv(shost); 3178 int chip_scsi_id; 3179 3180 seq_printf(m, 3181 "\nLinux Driver Configuration and Information for AdvanSys SCSI Host %d:\n", 3182 shost->host_no); 3183 3184 seq_printf(m, 3185 " host_busy %d, max_id %u, max_lun %llu, max_channel %u\n", 3186 scsi_host_busy(shost), shost->max_id, 3187 shost->max_lun, shost->max_channel); 3188 3189 seq_printf(m, 3190 " unique_id %d, can_queue %d, this_id %d, sg_tablesize %u, cmd_per_lun %u\n", 3191 shost->unique_id, shost->can_queue, shost->this_id, 3192 shost->sg_tablesize, shost->cmd_per_lun); 3193 3194 seq_printf(m, 3195 " unchecked_isa_dma %d, use_clustering %d\n", 3196 shost->unchecked_isa_dma, shost->use_clustering); 3197 3198 seq_printf(m, 3199 " flags 0x%x, last_reset 0x%lx, jiffies 0x%lx, asc_n_io_port 0x%x\n", 3200 boardp->flags, shost->last_reset, jiffies, 3201 boardp->asc_n_io_port); 3202 3203 seq_printf(m, " io_port 0x%lx\n", shost->io_port); 3204 3205 if (ASC_NARROW_BOARD(boardp)) { 3206 chip_scsi_id = boardp->dvc_cfg.asc_dvc_cfg.chip_scsi_id; 3207 } else { 3208 chip_scsi_id = boardp->dvc_var.adv_dvc_var.chip_scsi_id; 3209 } 3210 } 3211 3212 /* 3213 * asc_prt_asc_board_info() 3214 * 3215 * Print dynamic board configuration information. 3216 */ 3217 static void asc_prt_asc_board_info(struct seq_file *m, struct Scsi_Host *shost) 3218 { 3219 struct asc_board *boardp = shost_priv(shost); 3220 int chip_scsi_id; 3221 ASC_DVC_VAR *v; 3222 ASC_DVC_CFG *c; 3223 int i; 3224 int renegotiate = 0; 3225 3226 v = &boardp->dvc_var.asc_dvc_var; 3227 c = &boardp->dvc_cfg.asc_dvc_cfg; 3228 chip_scsi_id = c->chip_scsi_id; 3229 3230 seq_printf(m, 3231 "\nAsc Library Configuration and Statistics for AdvanSys SCSI Host %d:\n", 3232 shost->host_no); 3233 3234 seq_printf(m, " chip_version %u, mcode_date 0x%x, " 3235 "mcode_version 0x%x, err_code %u\n", 3236 c->chip_version, c->mcode_date, c->mcode_version, 3237 v->err_code); 3238 3239 /* Current number of commands waiting for the host. */ 3240 seq_printf(m, 3241 " Total Command Pending: %d\n", v->cur_total_qng); 3242 3243 seq_puts(m, " Command Queuing:"); 3244 for (i = 0; i <= ASC_MAX_TID; i++) { 3245 if ((chip_scsi_id == i) || 3246 ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) == 0)) { 3247 continue; 3248 } 3249 seq_printf(m, " %X:%c", 3250 i, 3251 (v->use_tagged_qng & ADV_TID_TO_TIDMASK(i)) ? 'Y' : 'N'); 3252 } 3253 3254 /* Current number of commands waiting for a device. */ 3255 seq_puts(m, "\n Command Queue Pending:"); 3256 for (i = 0; i <= ASC_MAX_TID; i++) { 3257 if ((chip_scsi_id == i) || 3258 ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) == 0)) { 3259 continue; 3260 } 3261 seq_printf(m, " %X:%u", i, v->cur_dvc_qng[i]); 3262 } 3263 3264 /* Current limit on number of commands that can be sent to a device. */ 3265 seq_puts(m, "\n Command Queue Limit:"); 3266 for (i = 0; i <= ASC_MAX_TID; i++) { 3267 if ((chip_scsi_id == i) || 3268 ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) == 0)) { 3269 continue; 3270 } 3271 seq_printf(m, " %X:%u", i, v->max_dvc_qng[i]); 3272 } 3273 3274 /* Indicate whether the device has returned queue full status. */ 3275 seq_puts(m, "\n Command Queue Full:"); 3276 for (i = 0; i <= ASC_MAX_TID; i++) { 3277 if ((chip_scsi_id == i) || 3278 ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) == 0)) { 3279 continue; 3280 } 3281 if (boardp->queue_full & ADV_TID_TO_TIDMASK(i)) 3282 seq_printf(m, " %X:Y-%d", 3283 i, boardp->queue_full_cnt[i]); 3284 else 3285 seq_printf(m, " %X:N", i); 3286 } 3287 3288 seq_puts(m, "\n Synchronous Transfer:"); 3289 for (i = 0; i <= ASC_MAX_TID; i++) { 3290 if ((chip_scsi_id == i) || 3291 ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) == 0)) { 3292 continue; 3293 } 3294 seq_printf(m, " %X:%c", 3295 i, 3296 (v->sdtr_done & ADV_TID_TO_TIDMASK(i)) ? 'Y' : 'N'); 3297 } 3298 seq_putc(m, '\n'); 3299 3300 for (i = 0; i <= ASC_MAX_TID; i++) { 3301 uchar syn_period_ix; 3302 3303 if ((chip_scsi_id == i) || 3304 ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) == 0) || 3305 ((v->init_sdtr & ADV_TID_TO_TIDMASK(i)) == 0)) { 3306 continue; 3307 } 3308 3309 seq_printf(m, " %X:", i); 3310 3311 if ((boardp->sdtr_data[i] & ASC_SYN_MAX_OFFSET) == 0) { 3312 seq_puts(m, " Asynchronous"); 3313 } else { 3314 syn_period_ix = 3315 (boardp->sdtr_data[i] >> 4) & (v->max_sdtr_index - 3316 1); 3317 3318 seq_printf(m, 3319 " Transfer Period Factor: %d (%d.%d Mhz),", 3320 v->sdtr_period_tbl[syn_period_ix], 3321 250 / v->sdtr_period_tbl[syn_period_ix], 3322 ASC_TENTHS(250, 3323 v->sdtr_period_tbl[syn_period_ix])); 3324 3325 seq_printf(m, " REQ/ACK Offset: %d", 3326 boardp->sdtr_data[i] & ASC_SYN_MAX_OFFSET); 3327 } 3328 3329 if ((v->sdtr_done & ADV_TID_TO_TIDMASK(i)) == 0) { 3330 seq_puts(m, "*\n"); 3331 renegotiate = 1; 3332 } else { 3333 seq_putc(m, '\n'); 3334 } 3335 } 3336 3337 if (renegotiate) { 3338 seq_puts(m, " * = Re-negotiation pending before next command.\n"); 3339 } 3340 } 3341 3342 /* 3343 * asc_prt_adv_board_info() 3344 * 3345 * Print dynamic board configuration information. 3346 */ 3347 static void asc_prt_adv_board_info(struct seq_file *m, struct Scsi_Host *shost) 3348 { 3349 struct asc_board *boardp = shost_priv(shost); 3350 int i; 3351 ADV_DVC_VAR *v; 3352 ADV_DVC_CFG *c; 3353 AdvPortAddr iop_base; 3354 ushort chip_scsi_id; 3355 ushort lramword; 3356 uchar lrambyte; 3357 ushort tagqng_able; 3358 ushort sdtr_able, wdtr_able; 3359 ushort wdtr_done, sdtr_done; 3360 ushort period = 0; 3361 int renegotiate = 0; 3362 3363 v = &boardp->dvc_var.adv_dvc_var; 3364 c = &boardp->dvc_cfg.adv_dvc_cfg; 3365 iop_base = v->iop_base; 3366 chip_scsi_id = v->chip_scsi_id; 3367 3368 seq_printf(m, 3369 "\nAdv Library Configuration and Statistics for AdvanSys SCSI Host %d:\n", 3370 shost->host_no); 3371 3372 seq_printf(m, 3373 " iop_base 0x%lx, cable_detect: %X, err_code %u\n", 3374 (unsigned long)v->iop_base, 3375 AdvReadWordRegister(iop_base,IOPW_SCSI_CFG1) & CABLE_DETECT, 3376 v->err_code); 3377 3378 seq_printf(m, " chip_version %u, mcode_date 0x%x, " 3379 "mcode_version 0x%x\n", c->chip_version, 3380 c->mcode_date, c->mcode_version); 3381 3382 AdvReadWordLram(iop_base, ASC_MC_TAGQNG_ABLE, tagqng_able); 3383 seq_puts(m, " Queuing Enabled:"); 3384 for (i = 0; i <= ADV_MAX_TID; i++) { 3385 if ((chip_scsi_id == i) || 3386 ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) == 0)) { 3387 continue; 3388 } 3389 3390 seq_printf(m, " %X:%c", 3391 i, 3392 (tagqng_able & ADV_TID_TO_TIDMASK(i)) ? 'Y' : 'N'); 3393 } 3394 3395 seq_puts(m, "\n Queue Limit:"); 3396 for (i = 0; i <= ADV_MAX_TID; i++) { 3397 if ((chip_scsi_id == i) || 3398 ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) == 0)) { 3399 continue; 3400 } 3401 3402 AdvReadByteLram(iop_base, ASC_MC_NUMBER_OF_MAX_CMD + i, 3403 lrambyte); 3404 3405 seq_printf(m, " %X:%d", i, lrambyte); 3406 } 3407 3408 seq_puts(m, "\n Command Pending:"); 3409 for (i = 0; i <= ADV_MAX_TID; i++) { 3410 if ((chip_scsi_id == i) || 3411 ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) == 0)) { 3412 continue; 3413 } 3414 3415 AdvReadByteLram(iop_base, ASC_MC_NUMBER_OF_QUEUED_CMD + i, 3416 lrambyte); 3417 3418 seq_printf(m, " %X:%d", i, lrambyte); 3419 } 3420 seq_putc(m, '\n'); 3421 3422 AdvReadWordLram(iop_base, ASC_MC_WDTR_ABLE, wdtr_able); 3423 seq_puts(m, " Wide Enabled:"); 3424 for (i = 0; i <= ADV_MAX_TID; i++) { 3425 if ((chip_scsi_id == i) || 3426 ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) == 0)) { 3427 continue; 3428 } 3429 3430 seq_printf(m, " %X:%c", 3431 i, 3432 (wdtr_able & ADV_TID_TO_TIDMASK(i)) ? 'Y' : 'N'); 3433 } 3434 seq_putc(m, '\n'); 3435 3436 AdvReadWordLram(iop_base, ASC_MC_WDTR_DONE, wdtr_done); 3437 seq_puts(m, " Transfer Bit Width:"); 3438 for (i = 0; i <= ADV_MAX_TID; i++) { 3439 if ((chip_scsi_id == i) || 3440 ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) == 0)) { 3441 continue; 3442 } 3443 3444 AdvReadWordLram(iop_base, 3445 ASC_MC_DEVICE_HSHK_CFG_TABLE + (2 * i), 3446 lramword); 3447 3448 seq_printf(m, " %X:%d", 3449 i, (lramword & 0x8000) ? 16 : 8); 3450 3451 if ((wdtr_able & ADV_TID_TO_TIDMASK(i)) && 3452 (wdtr_done & ADV_TID_TO_TIDMASK(i)) == 0) { 3453 seq_putc(m, '*'); 3454 renegotiate = 1; 3455 } 3456 } 3457 seq_putc(m, '\n'); 3458 3459 AdvReadWordLram(iop_base, ASC_MC_SDTR_ABLE, sdtr_able); 3460 seq_puts(m, " Synchronous Enabled:"); 3461 for (i = 0; i <= ADV_MAX_TID; i++) { 3462 if ((chip_scsi_id == i) || 3463 ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) == 0)) { 3464 continue; 3465 } 3466 3467 seq_printf(m, " %X:%c", 3468 i, 3469 (sdtr_able & ADV_TID_TO_TIDMASK(i)) ? 'Y' : 'N'); 3470 } 3471 seq_putc(m, '\n'); 3472 3473 AdvReadWordLram(iop_base, ASC_MC_SDTR_DONE, sdtr_done); 3474 for (i = 0; i <= ADV_MAX_TID; i++) { 3475 3476 AdvReadWordLram(iop_base, 3477 ASC_MC_DEVICE_HSHK_CFG_TABLE + (2 * i), 3478 lramword); 3479 lramword &= ~0x8000; 3480 3481 if ((chip_scsi_id == i) || 3482 ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(i)) == 0) || 3483 ((sdtr_able & ADV_TID_TO_TIDMASK(i)) == 0)) { 3484 continue; 3485 } 3486 3487 seq_printf(m, " %X:", i); 3488 3489 if ((lramword & 0x1F) == 0) { /* Check for REQ/ACK Offset 0. */ 3490 seq_puts(m, " Asynchronous"); 3491 } else { 3492 seq_puts(m, " Transfer Period Factor: "); 3493 3494 if ((lramword & 0x1F00) == 0x1100) { /* 80 Mhz */ 3495 seq_puts(m, "9 (80.0 Mhz),"); 3496 } else if ((lramword & 0x1F00) == 0x1000) { /* 40 Mhz */ 3497 seq_puts(m, "10 (40.0 Mhz),"); 3498 } else { /* 20 Mhz or below. */ 3499 3500 period = (((lramword >> 8) * 25) + 50) / 4; 3501 3502 if (period == 0) { /* Should never happen. */ 3503 seq_printf(m, "%d (? Mhz), ", period); 3504 } else { 3505 seq_printf(m, 3506 "%d (%d.%d Mhz),", 3507 period, 250 / period, 3508 ASC_TENTHS(250, period)); 3509 } 3510 } 3511 3512 seq_printf(m, " REQ/ACK Offset: %d", 3513 lramword & 0x1F); 3514 } 3515 3516 if ((sdtr_done & ADV_TID_TO_TIDMASK(i)) == 0) { 3517 seq_puts(m, "*\n"); 3518 renegotiate = 1; 3519 } else { 3520 seq_putc(m, '\n'); 3521 } 3522 } 3523 3524 if (renegotiate) { 3525 seq_puts(m, " * = Re-negotiation pending before next command.\n"); 3526 } 3527 } 3528 3529 #ifdef ADVANSYS_STATS 3530 /* 3531 * asc_prt_board_stats() 3532 */ 3533 static void asc_prt_board_stats(struct seq_file *m, struct Scsi_Host *shost) 3534 { 3535 struct asc_board *boardp = shost_priv(shost); 3536 struct asc_stats *s = &boardp->asc_stats; 3537 3538 seq_printf(m, 3539 "\nLinux Driver Statistics for AdvanSys SCSI Host %d:\n", 3540 shost->host_no); 3541 3542 seq_printf(m, 3543 " queuecommand %u, reset %u, biosparam %u, interrupt %u\n", 3544 s->queuecommand, s->reset, s->biosparam, 3545 s->interrupt); 3546 3547 seq_printf(m, 3548 " callback %u, done %u, build_error %u, build_noreq %u, build_nosg %u\n", 3549 s->callback, s->done, s->build_error, 3550 s->adv_build_noreq, s->adv_build_nosg); 3551 3552 seq_printf(m, 3553 " exe_noerror %u, exe_busy %u, exe_error %u, exe_unknown %u\n", 3554 s->exe_noerror, s->exe_busy, s->exe_error, 3555 s->exe_unknown); 3556 3557 /* 3558 * Display data transfer statistics. 3559 */ 3560 if (s->xfer_cnt > 0) { 3561 seq_printf(m, " xfer_cnt %u, xfer_elem %u, ", 3562 s->xfer_cnt, s->xfer_elem); 3563 3564 seq_printf(m, "xfer_bytes %u.%01u kb\n", 3565 s->xfer_sect / 2, ASC_TENTHS(s->xfer_sect, 2)); 3566 3567 /* Scatter gather transfer statistics */ 3568 seq_printf(m, " avg_num_elem %u.%01u, ", 3569 s->xfer_elem / s->xfer_cnt, 3570 ASC_TENTHS(s->xfer_elem, s->xfer_cnt)); 3571 3572 seq_printf(m, "avg_elem_size %u.%01u kb, ", 3573 (s->xfer_sect / 2) / s->xfer_elem, 3574 ASC_TENTHS((s->xfer_sect / 2), s->xfer_elem)); 3575 3576 seq_printf(m, "avg_xfer_size %u.%01u kb\n", 3577 (s->xfer_sect / 2) / s->xfer_cnt, 3578 ASC_TENTHS((s->xfer_sect / 2), s->xfer_cnt)); 3579 } 3580 } 3581 #endif /* ADVANSYS_STATS */ 3582 3583 /* 3584 * advansys_show_info() - /proc/scsi/advansys/{0,1,2,3,...} 3585 * 3586 * m: seq_file to print into 3587 * shost: Scsi_Host 3588 * 3589 * Return the number of bytes read from or written to a 3590 * /proc/scsi/advansys/[0...] file. 3591 */ 3592 static int 3593 advansys_show_info(struct seq_file *m, struct Scsi_Host *shost) 3594 { 3595 struct asc_board *boardp = shost_priv(shost); 3596 3597 ASC_DBG(1, "begin\n"); 3598 3599 /* 3600 * User read of /proc/scsi/advansys/[0...] file. 3601 */ 3602 3603 /* 3604 * Get board configuration information. 3605 * 3606 * advansys_info() returns the board string from its own static buffer. 3607 */ 3608 /* Copy board information. */ 3609 seq_printf(m, "%s\n", (char *)advansys_info(shost)); 3610 /* 3611 * Display Wide Board BIOS Information. 3612 */ 3613 if (!ASC_NARROW_BOARD(boardp)) 3614 asc_prt_adv_bios(m, shost); 3615 3616 /* 3617 * Display driver information for each device attached to the board. 3618 */ 3619 asc_prt_board_devices(m, shost); 3620 3621 /* 3622 * Display EEPROM configuration for the board. 3623 */ 3624 if (ASC_NARROW_BOARD(boardp)) 3625 asc_prt_asc_board_eeprom(m, shost); 3626 else 3627 asc_prt_adv_board_eeprom(m, shost); 3628 3629 /* 3630 * Display driver configuration and information for the board. 3631 */ 3632 asc_prt_driver_conf(m, shost); 3633 3634 #ifdef ADVANSYS_STATS 3635 /* 3636 * Display driver statistics for the board. 3637 */ 3638 asc_prt_board_stats(m, shost); 3639 #endif /* ADVANSYS_STATS */ 3640 3641 /* 3642 * Display Asc Library dynamic configuration information 3643 * for the board. 3644 */ 3645 if (ASC_NARROW_BOARD(boardp)) 3646 asc_prt_asc_board_info(m, shost); 3647 else 3648 asc_prt_adv_board_info(m, shost); 3649 return 0; 3650 } 3651 #endif /* CONFIG_PROC_FS */ 3652 3653 static void asc_scsi_done(struct scsi_cmnd *scp) 3654 { 3655 scsi_dma_unmap(scp); 3656 ASC_STATS(scp->device->host, done); 3657 scp->scsi_done(scp); 3658 } 3659 3660 static void AscSetBank(PortAddr iop_base, uchar bank) 3661 { 3662 uchar val; 3663 3664 val = AscGetChipControl(iop_base) & 3665 (~ 3666 (CC_SINGLE_STEP | CC_TEST | CC_DIAG | CC_SCSI_RESET | 3667 CC_CHIP_RESET)); 3668 if (bank == 1) { 3669 val |= CC_BANK_ONE; 3670 } else if (bank == 2) { 3671 val |= CC_DIAG | CC_BANK_ONE; 3672 } else { 3673 val &= ~CC_BANK_ONE; 3674 } 3675 AscSetChipControl(iop_base, val); 3676 } 3677 3678 static void AscSetChipIH(PortAddr iop_base, ushort ins_code) 3679 { 3680 AscSetBank(iop_base, 1); 3681 AscWriteChipIH(iop_base, ins_code); 3682 AscSetBank(iop_base, 0); 3683 } 3684 3685 static int AscStartChip(PortAddr iop_base) 3686 { 3687 AscSetChipControl(iop_base, 0); 3688 if ((AscGetChipStatus(iop_base) & CSW_HALTED) != 0) { 3689 return (0); 3690 } 3691 return (1); 3692 } 3693 3694 static bool AscStopChip(PortAddr iop_base) 3695 { 3696 uchar cc_val; 3697 3698 cc_val = 3699 AscGetChipControl(iop_base) & 3700 (~(CC_SINGLE_STEP | CC_TEST | CC_DIAG)); 3701 AscSetChipControl(iop_base, (uchar)(cc_val | CC_HALT)); 3702 AscSetChipIH(iop_base, INS_HALT); 3703 AscSetChipIH(iop_base, INS_RFLAG_WTM); 3704 if ((AscGetChipStatus(iop_base) & CSW_HALTED) == 0) { 3705 return false; 3706 } 3707 return true; 3708 } 3709 3710 static bool AscIsChipHalted(PortAddr iop_base) 3711 { 3712 if ((AscGetChipStatus(iop_base) & CSW_HALTED) != 0) { 3713 if ((AscGetChipControl(iop_base) & CC_HALT) != 0) { 3714 return true; 3715 } 3716 } 3717 return false; 3718 } 3719 3720 static bool AscResetChipAndScsiBus(ASC_DVC_VAR *asc_dvc) 3721 { 3722 PortAddr iop_base; 3723 int i = 10; 3724 3725 iop_base = asc_dvc->iop_base; 3726 while ((AscGetChipStatus(iop_base) & CSW_SCSI_RESET_ACTIVE) 3727 && (i-- > 0)) { 3728 mdelay(100); 3729 } 3730 AscStopChip(iop_base); 3731 AscSetChipControl(iop_base, CC_CHIP_RESET | CC_SCSI_RESET | CC_HALT); 3732 udelay(60); 3733 AscSetChipIH(iop_base, INS_RFLAG_WTM); 3734 AscSetChipIH(iop_base, INS_HALT); 3735 AscSetChipControl(iop_base, CC_CHIP_RESET | CC_HALT); 3736 AscSetChipControl(iop_base, CC_HALT); 3737 mdelay(200); 3738 AscSetChipStatus(iop_base, CIW_CLR_SCSI_RESET_INT); 3739 AscSetChipStatus(iop_base, 0); 3740 return (AscIsChipHalted(iop_base)); 3741 } 3742 3743 static int AscFindSignature(PortAddr iop_base) 3744 { 3745 ushort sig_word; 3746 3747 ASC_DBG(1, "AscGetChipSignatureByte(0x%x) 0x%x\n", 3748 iop_base, AscGetChipSignatureByte(iop_base)); 3749 if (AscGetChipSignatureByte(iop_base) == (uchar)ASC_1000_ID1B) { 3750 ASC_DBG(1, "AscGetChipSignatureWord(0x%x) 0x%x\n", 3751 iop_base, AscGetChipSignatureWord(iop_base)); 3752 sig_word = AscGetChipSignatureWord(iop_base); 3753 if ((sig_word == (ushort)ASC_1000_ID0W) || 3754 (sig_word == (ushort)ASC_1000_ID0W_FIX)) { 3755 return (1); 3756 } 3757 } 3758 return (0); 3759 } 3760 3761 static void AscEnableInterrupt(PortAddr iop_base) 3762 { 3763 ushort cfg; 3764 3765 cfg = AscGetChipCfgLsw(iop_base); 3766 AscSetChipCfgLsw(iop_base, cfg | ASC_CFG0_HOST_INT_ON); 3767 } 3768 3769 static void AscDisableInterrupt(PortAddr iop_base) 3770 { 3771 ushort cfg; 3772 3773 cfg = AscGetChipCfgLsw(iop_base); 3774 AscSetChipCfgLsw(iop_base, cfg & (~ASC_CFG0_HOST_INT_ON)); 3775 } 3776 3777 static uchar AscReadLramByte(PortAddr iop_base, ushort addr) 3778 { 3779 unsigned char byte_data; 3780 unsigned short word_data; 3781 3782 if (isodd_word(addr)) { 3783 AscSetChipLramAddr(iop_base, addr - 1); 3784 word_data = AscGetChipLramData(iop_base); 3785 byte_data = (word_data >> 8) & 0xFF; 3786 } else { 3787 AscSetChipLramAddr(iop_base, addr); 3788 word_data = AscGetChipLramData(iop_base); 3789 byte_data = word_data & 0xFF; 3790 } 3791 return byte_data; 3792 } 3793 3794 static ushort AscReadLramWord(PortAddr iop_base, ushort addr) 3795 { 3796 ushort word_data; 3797 3798 AscSetChipLramAddr(iop_base, addr); 3799 word_data = AscGetChipLramData(iop_base); 3800 return (word_data); 3801 } 3802 3803 static void 3804 AscMemWordSetLram(PortAddr iop_base, ushort s_addr, ushort set_wval, int words) 3805 { 3806 int i; 3807 3808 AscSetChipLramAddr(iop_base, s_addr); 3809 for (i = 0; i < words; i++) { 3810 AscSetChipLramData(iop_base, set_wval); 3811 } 3812 } 3813 3814 static void AscWriteLramWord(PortAddr iop_base, ushort addr, ushort word_val) 3815 { 3816 AscSetChipLramAddr(iop_base, addr); 3817 AscSetChipLramData(iop_base, word_val); 3818 } 3819 3820 static void AscWriteLramByte(PortAddr iop_base, ushort addr, uchar byte_val) 3821 { 3822 ushort word_data; 3823 3824 if (isodd_word(addr)) { 3825 addr--; 3826 word_data = AscReadLramWord(iop_base, addr); 3827 word_data &= 0x00FF; 3828 word_data |= (((ushort)byte_val << 8) & 0xFF00); 3829 } else { 3830 word_data = AscReadLramWord(iop_base, addr); 3831 word_data &= 0xFF00; 3832 word_data |= ((ushort)byte_val & 0x00FF); 3833 } 3834 AscWriteLramWord(iop_base, addr, word_data); 3835 } 3836 3837 /* 3838 * Copy 2 bytes to LRAM. 3839 * 3840 * The source data is assumed to be in little-endian order in memory 3841 * and is maintained in little-endian order when written to LRAM. 3842 */ 3843 static void 3844 AscMemWordCopyPtrToLram(PortAddr iop_base, ushort s_addr, 3845 const uchar *s_buffer, int words) 3846 { 3847 int i; 3848 3849 AscSetChipLramAddr(iop_base, s_addr); 3850 for (i = 0; i < 2 * words; i += 2) { 3851 /* 3852 * On a little-endian system the second argument below 3853 * produces a little-endian ushort which is written to 3854 * LRAM in little-endian order. On a big-endian system 3855 * the second argument produces a big-endian ushort which 3856 * is "transparently" byte-swapped by outpw() and written 3857 * in little-endian order to LRAM. 3858 */ 3859 outpw(iop_base + IOP_RAM_DATA, 3860 ((ushort)s_buffer[i + 1] << 8) | s_buffer[i]); 3861 } 3862 } 3863 3864 /* 3865 * Copy 4 bytes to LRAM. 3866 * 3867 * The source data is assumed to be in little-endian order in memory 3868 * and is maintained in little-endian order when written to LRAM. 3869 */ 3870 static void 3871 AscMemDWordCopyPtrToLram(PortAddr iop_base, 3872 ushort s_addr, uchar *s_buffer, int dwords) 3873 { 3874 int i; 3875 3876 AscSetChipLramAddr(iop_base, s_addr); 3877 for (i = 0; i < 4 * dwords; i += 4) { 3878 outpw(iop_base + IOP_RAM_DATA, ((ushort)s_buffer[i + 1] << 8) | s_buffer[i]); /* LSW */ 3879 outpw(iop_base + IOP_RAM_DATA, ((ushort)s_buffer[i + 3] << 8) | s_buffer[i + 2]); /* MSW */ 3880 } 3881 } 3882 3883 /* 3884 * Copy 2 bytes from LRAM. 3885 * 3886 * The source data is assumed to be in little-endian order in LRAM 3887 * and is maintained in little-endian order when written to memory. 3888 */ 3889 static void 3890 AscMemWordCopyPtrFromLram(PortAddr iop_base, 3891 ushort s_addr, uchar *d_buffer, int words) 3892 { 3893 int i; 3894 ushort word; 3895 3896 AscSetChipLramAddr(iop_base, s_addr); 3897 for (i = 0; i < 2 * words; i += 2) { 3898 word = inpw(iop_base + IOP_RAM_DATA); 3899 d_buffer[i] = word & 0xff; 3900 d_buffer[i + 1] = (word >> 8) & 0xff; 3901 } 3902 } 3903 3904 static u32 AscMemSumLramWord(PortAddr iop_base, ushort s_addr, int words) 3905 { 3906 u32 sum = 0; 3907 int i; 3908 3909 for (i = 0; i < words; i++, s_addr += 2) { 3910 sum += AscReadLramWord(iop_base, s_addr); 3911 } 3912 return (sum); 3913 } 3914 3915 static void AscInitLram(ASC_DVC_VAR *asc_dvc) 3916 { 3917 uchar i; 3918 ushort s_addr; 3919 PortAddr iop_base; 3920 3921 iop_base = asc_dvc->iop_base; 3922 AscMemWordSetLram(iop_base, ASC_QADR_BEG, 0, 3923 (ushort)(((int)(asc_dvc->max_total_qng + 2 + 1) * 3924 64) >> 1)); 3925 i = ASC_MIN_ACTIVE_QNO; 3926 s_addr = ASC_QADR_BEG + ASC_QBLK_SIZE; 3927 AscWriteLramByte(iop_base, (ushort)(s_addr + ASC_SCSIQ_B_FWD), 3928 (uchar)(i + 1)); 3929 AscWriteLramByte(iop_base, (ushort)(s_addr + ASC_SCSIQ_B_BWD), 3930 (uchar)(asc_dvc->max_total_qng)); 3931 AscWriteLramByte(iop_base, (ushort)(s_addr + ASC_SCSIQ_B_QNO), 3932 (uchar)i); 3933 i++; 3934 s_addr += ASC_QBLK_SIZE; 3935 for (; i < asc_dvc->max_total_qng; i++, s_addr += ASC_QBLK_SIZE) { 3936 AscWriteLramByte(iop_base, (ushort)(s_addr + ASC_SCSIQ_B_FWD), 3937 (uchar)(i + 1)); 3938 AscWriteLramByte(iop_base, (ushort)(s_addr + ASC_SCSIQ_B_BWD), 3939 (uchar)(i - 1)); 3940 AscWriteLramByte(iop_base, (ushort)(s_addr + ASC_SCSIQ_B_QNO), 3941 (uchar)i); 3942 } 3943 AscWriteLramByte(iop_base, (ushort)(s_addr + ASC_SCSIQ_B_FWD), 3944 (uchar)ASC_QLINK_END); 3945 AscWriteLramByte(iop_base, (ushort)(s_addr + ASC_SCSIQ_B_BWD), 3946 (uchar)(asc_dvc->max_total_qng - 1)); 3947 AscWriteLramByte(iop_base, (ushort)(s_addr + ASC_SCSIQ_B_QNO), 3948 (uchar)asc_dvc->max_total_qng); 3949 i++; 3950 s_addr += ASC_QBLK_SIZE; 3951 for (; i <= (uchar)(asc_dvc->max_total_qng + 3); 3952 i++, s_addr += ASC_QBLK_SIZE) { 3953 AscWriteLramByte(iop_base, 3954 (ushort)(s_addr + (ushort)ASC_SCSIQ_B_FWD), i); 3955 AscWriteLramByte(iop_base, 3956 (ushort)(s_addr + (ushort)ASC_SCSIQ_B_BWD), i); 3957 AscWriteLramByte(iop_base, 3958 (ushort)(s_addr + (ushort)ASC_SCSIQ_B_QNO), i); 3959 } 3960 } 3961 3962 static u32 3963 AscLoadMicroCode(PortAddr iop_base, ushort s_addr, 3964 const uchar *mcode_buf, ushort mcode_size) 3965 { 3966 u32 chksum; 3967 ushort mcode_word_size; 3968 ushort mcode_chksum; 3969 3970 /* Write the microcode buffer starting at LRAM address 0. */ 3971 mcode_word_size = (ushort)(mcode_size >> 1); 3972 AscMemWordSetLram(iop_base, s_addr, 0, mcode_word_size); 3973 AscMemWordCopyPtrToLram(iop_base, s_addr, mcode_buf, mcode_word_size); 3974 3975 chksum = AscMemSumLramWord(iop_base, s_addr, mcode_word_size); 3976 ASC_DBG(1, "chksum 0x%lx\n", (ulong)chksum); 3977 mcode_chksum = (ushort)AscMemSumLramWord(iop_base, 3978 (ushort)ASC_CODE_SEC_BEG, 3979 (ushort)((mcode_size - 3980 s_addr - (ushort) 3981 ASC_CODE_SEC_BEG) / 3982 2)); 3983 ASC_DBG(1, "mcode_chksum 0x%lx\n", (ulong)mcode_chksum); 3984 AscWriteLramWord(iop_base, ASCV_MCODE_CHKSUM_W, mcode_chksum); 3985 AscWriteLramWord(iop_base, ASCV_MCODE_SIZE_W, mcode_size); 3986 return chksum; 3987 } 3988 3989 static void AscInitQLinkVar(ASC_DVC_VAR *asc_dvc) 3990 { 3991 PortAddr iop_base; 3992 int i; 3993 ushort lram_addr; 3994 3995 iop_base = asc_dvc->iop_base; 3996 AscPutRiscVarFreeQHead(iop_base, 1); 3997 AscPutRiscVarDoneQTail(iop_base, asc_dvc->max_total_qng); 3998 AscPutVarFreeQHead(iop_base, 1); 3999 AscPutVarDoneQTail(iop_base, asc_dvc->max_total_qng); 4000 AscWriteLramByte(iop_base, ASCV_BUSY_QHEAD_B, 4001 (uchar)((int)asc_dvc->max_total_qng + 1)); 4002 AscWriteLramByte(iop_base, ASCV_DISC1_QHEAD_B, 4003 (uchar)((int)asc_dvc->max_total_qng + 2)); 4004 AscWriteLramByte(iop_base, (ushort)ASCV_TOTAL_READY_Q_B, 4005 asc_dvc->max_total_qng); 4006 AscWriteLramWord(iop_base, ASCV_ASCDVC_ERR_CODE_W, 0); 4007 AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0); 4008 AscWriteLramByte(iop_base, ASCV_STOP_CODE_B, 0); 4009 AscWriteLramByte(iop_base, ASCV_SCSIBUSY_B, 0); 4010 AscWriteLramByte(iop_base, ASCV_WTM_FLAG_B, 0); 4011 AscPutQDoneInProgress(iop_base, 0); 4012 lram_addr = ASC_QADR_BEG; 4013 for (i = 0; i < 32; i++, lram_addr += 2) { 4014 AscWriteLramWord(iop_base, lram_addr, 0); 4015 } 4016 } 4017 4018 static int AscInitMicroCodeVar(ASC_DVC_VAR *asc_dvc) 4019 { 4020 int i; 4021 int warn_code; 4022 PortAddr iop_base; 4023 __le32 phy_addr; 4024 __le32 phy_size; 4025 struct asc_board *board = asc_dvc_to_board(asc_dvc); 4026 4027 iop_base = asc_dvc->iop_base; 4028 warn_code = 0; 4029 for (i = 0; i <= ASC_MAX_TID; i++) { 4030 AscPutMCodeInitSDTRAtID(iop_base, i, 4031 asc_dvc->cfg->sdtr_period_offset[i]); 4032 } 4033 4034 AscInitQLinkVar(asc_dvc); 4035 AscWriteLramByte(iop_base, ASCV_DISC_ENABLE_B, 4036 asc_dvc->cfg->disc_enable); 4037 AscWriteLramByte(iop_base, ASCV_HOSTSCSI_ID_B, 4038 ASC_TID_TO_TARGET_ID(asc_dvc->cfg->chip_scsi_id)); 4039 4040 /* Ensure overrun buffer is aligned on an 8 byte boundary. */ 4041 BUG_ON((unsigned long)asc_dvc->overrun_buf & 7); 4042 asc_dvc->overrun_dma = dma_map_single(board->dev, asc_dvc->overrun_buf, 4043 ASC_OVERRUN_BSIZE, DMA_FROM_DEVICE); 4044 if (dma_mapping_error(board->dev, asc_dvc->overrun_dma)) { 4045 warn_code = -ENOMEM; 4046 goto err_dma_map; 4047 } 4048 phy_addr = cpu_to_le32(asc_dvc->overrun_dma); 4049 AscMemDWordCopyPtrToLram(iop_base, ASCV_OVERRUN_PADDR_D, 4050 (uchar *)&phy_addr, 1); 4051 phy_size = cpu_to_le32(ASC_OVERRUN_BSIZE); 4052 AscMemDWordCopyPtrToLram(iop_base, ASCV_OVERRUN_BSIZE_D, 4053 (uchar *)&phy_size, 1); 4054 4055 asc_dvc->cfg->mcode_date = 4056 AscReadLramWord(iop_base, (ushort)ASCV_MC_DATE_W); 4057 asc_dvc->cfg->mcode_version = 4058 AscReadLramWord(iop_base, (ushort)ASCV_MC_VER_W); 4059 4060 AscSetPCAddr(iop_base, ASC_MCODE_START_ADDR); 4061 if (AscGetPCAddr(iop_base) != ASC_MCODE_START_ADDR) { 4062 asc_dvc->err_code |= ASC_IERR_SET_PC_ADDR; 4063 warn_code = -EINVAL; 4064 goto err_mcode_start; 4065 } 4066 if (AscStartChip(iop_base) != 1) { 4067 asc_dvc->err_code |= ASC_IERR_START_STOP_CHIP; 4068 warn_code = -EIO; 4069 goto err_mcode_start; 4070 } 4071 4072 return warn_code; 4073 4074 err_mcode_start: 4075 dma_unmap_single(board->dev, asc_dvc->overrun_dma, 4076 ASC_OVERRUN_BSIZE, DMA_FROM_DEVICE); 4077 err_dma_map: 4078 asc_dvc->overrun_dma = 0; 4079 return warn_code; 4080 } 4081 4082 static int AscInitAsc1000Driver(ASC_DVC_VAR *asc_dvc) 4083 { 4084 const struct firmware *fw; 4085 const char fwname[] = "advansys/mcode.bin"; 4086 int err; 4087 unsigned long chksum; 4088 int warn_code; 4089 PortAddr iop_base; 4090 4091 iop_base = asc_dvc->iop_base; 4092 warn_code = 0; 4093 if ((asc_dvc->dvc_cntl & ASC_CNTL_RESET_SCSI) && 4094 !(asc_dvc->init_state & ASC_INIT_RESET_SCSI_DONE)) { 4095 AscResetChipAndScsiBus(asc_dvc); 4096 mdelay(asc_dvc->scsi_reset_wait * 1000); /* XXX: msleep? */ 4097 } 4098 asc_dvc->init_state |= ASC_INIT_STATE_BEG_LOAD_MC; 4099 if (asc_dvc->err_code != 0) 4100 return ASC_ERROR; 4101 if (!AscFindSignature(asc_dvc->iop_base)) { 4102 asc_dvc->err_code = ASC_IERR_BAD_SIGNATURE; 4103 return warn_code; 4104 } 4105 AscDisableInterrupt(iop_base); 4106 AscInitLram(asc_dvc); 4107 4108 err = request_firmware(&fw, fwname, asc_dvc->drv_ptr->dev); 4109 if (err) { 4110 printk(KERN_ERR "Failed to load image \"%s\" err %d\n", 4111 fwname, err); 4112 asc_dvc->err_code |= ASC_IERR_MCODE_CHKSUM; 4113 return err; 4114 } 4115 if (fw->size < 4) { 4116 printk(KERN_ERR "Bogus length %zu in image \"%s\"\n", 4117 fw->size, fwname); 4118 release_firmware(fw); 4119 asc_dvc->err_code |= ASC_IERR_MCODE_CHKSUM; 4120 return -EINVAL; 4121 } 4122 chksum = (fw->data[3] << 24) | (fw->data[2] << 16) | 4123 (fw->data[1] << 8) | fw->data[0]; 4124 ASC_DBG(1, "_asc_mcode_chksum 0x%lx\n", (ulong)chksum); 4125 if (AscLoadMicroCode(iop_base, 0, &fw->data[4], 4126 fw->size - 4) != chksum) { 4127 asc_dvc->err_code |= ASC_IERR_MCODE_CHKSUM; 4128 release_firmware(fw); 4129 return warn_code; 4130 } 4131 release_firmware(fw); 4132 warn_code |= AscInitMicroCodeVar(asc_dvc); 4133 if (!asc_dvc->overrun_dma) 4134 return warn_code; 4135 asc_dvc->init_state |= ASC_INIT_STATE_END_LOAD_MC; 4136 AscEnableInterrupt(iop_base); 4137 return warn_code; 4138 } 4139 4140 /* 4141 * Load the Microcode 4142 * 4143 * Write the microcode image to RISC memory starting at address 0. 4144 * 4145 * The microcode is stored compressed in the following format: 4146 * 4147 * 254 word (508 byte) table indexed by byte code followed 4148 * by the following byte codes: 4149 * 4150 * 1-Byte Code: 4151 * 00: Emit word 0 in table. 4152 * 01: Emit word 1 in table. 4153 * . 4154 * FD: Emit word 253 in table. 4155 * 4156 * Multi-Byte Code: 4157 * FE WW WW: (3 byte code) Word to emit is the next word WW WW. 4158 * FF BB WW WW: (4 byte code) Emit BB count times next word WW WW. 4159 * 4160 * Returns 0 or an error if the checksum doesn't match 4161 */ 4162 static int AdvLoadMicrocode(AdvPortAddr iop_base, const unsigned char *buf, 4163 int size, int memsize, int chksum) 4164 { 4165 int i, j, end, len = 0; 4166 u32 sum; 4167 4168 AdvWriteWordRegister(iop_base, IOPW_RAM_ADDR, 0); 4169 4170 for (i = 253 * 2; i < size; i++) { 4171 if (buf[i] == 0xff) { 4172 unsigned short word = (buf[i + 3] << 8) | buf[i + 2]; 4173 for (j = 0; j < buf[i + 1]; j++) { 4174 AdvWriteWordAutoIncLram(iop_base, word); 4175 len += 2; 4176 } 4177 i += 3; 4178 } else if (buf[i] == 0xfe) { 4179 unsigned short word = (buf[i + 2] << 8) | buf[i + 1]; 4180 AdvWriteWordAutoIncLram(iop_base, word); 4181 i += 2; 4182 len += 2; 4183 } else { 4184 unsigned int off = buf[i] * 2; 4185 unsigned short word = (buf[off + 1] << 8) | buf[off]; 4186 AdvWriteWordAutoIncLram(iop_base, word); 4187 len += 2; 4188 } 4189 } 4190 4191 end = len; 4192 4193 while (len < memsize) { 4194 AdvWriteWordAutoIncLram(iop_base, 0); 4195 len += 2; 4196 } 4197 4198 /* Verify the microcode checksum. */ 4199 sum = 0; 4200 AdvWriteWordRegister(iop_base, IOPW_RAM_ADDR, 0); 4201 4202 for (len = 0; len < end; len += 2) { 4203 sum += AdvReadWordAutoIncLram(iop_base); 4204 } 4205 4206 if (sum != chksum) 4207 return ASC_IERR_MCODE_CHKSUM; 4208 4209 return 0; 4210 } 4211 4212 static void AdvBuildCarrierFreelist(struct adv_dvc_var *adv_dvc) 4213 { 4214 off_t carr_offset = 0, next_offset; 4215 dma_addr_t carr_paddr; 4216 int carr_num = ADV_CARRIER_BUFSIZE / sizeof(ADV_CARR_T), i; 4217 4218 for (i = 0; i < carr_num; i++) { 4219 carr_offset = i * sizeof(ADV_CARR_T); 4220 /* Get physical address of the carrier 'carrp'. */ 4221 carr_paddr = adv_dvc->carrier_addr + carr_offset; 4222 4223 adv_dvc->carrier[i].carr_pa = cpu_to_le32(carr_paddr); 4224 adv_dvc->carrier[i].carr_va = cpu_to_le32(carr_offset); 4225 adv_dvc->carrier[i].areq_vpa = 0; 4226 next_offset = carr_offset + sizeof(ADV_CARR_T); 4227 if (i == carr_num) 4228 next_offset = ~0; 4229 adv_dvc->carrier[i].next_vpa = cpu_to_le32(next_offset); 4230 } 4231 /* 4232 * We cannot have a carrier with 'carr_va' of '0', as 4233 * a reference to this carrier would be interpreted as 4234 * list termination. 4235 * So start at carrier 1 with the freelist. 4236 */ 4237 adv_dvc->carr_freelist = &adv_dvc->carrier[1]; 4238 } 4239 4240 static ADV_CARR_T *adv_get_carrier(struct adv_dvc_var *adv_dvc, u32 offset) 4241 { 4242 int index; 4243 4244 BUG_ON(offset > ADV_CARRIER_BUFSIZE); 4245 4246 index = offset / sizeof(ADV_CARR_T); 4247 return &adv_dvc->carrier[index]; 4248 } 4249 4250 static ADV_CARR_T *adv_get_next_carrier(struct adv_dvc_var *adv_dvc) 4251 { 4252 ADV_CARR_T *carrp = adv_dvc->carr_freelist; 4253 u32 next_vpa = le32_to_cpu(carrp->next_vpa); 4254 4255 if (next_vpa == 0 || next_vpa == ~0) { 4256 ASC_DBG(1, "invalid vpa offset 0x%x\n", next_vpa); 4257 return NULL; 4258 } 4259 4260 adv_dvc->carr_freelist = adv_get_carrier(adv_dvc, next_vpa); 4261 /* 4262 * insert stopper carrier to terminate list 4263 */ 4264 carrp->next_vpa = cpu_to_le32(ADV_CQ_STOPPER); 4265 4266 return carrp; 4267 } 4268 4269 /* 4270 * 'offset' is the index in the request pointer array 4271 */ 4272 static adv_req_t * adv_get_reqp(struct adv_dvc_var *adv_dvc, u32 offset) 4273 { 4274 struct asc_board *boardp = adv_dvc->drv_ptr; 4275 4276 BUG_ON(offset > adv_dvc->max_host_qng); 4277 return &boardp->adv_reqp[offset]; 4278 } 4279 4280 /* 4281 * Send an idle command to the chip and wait for completion. 4282 * 4283 * Command completion is polled for once per microsecond. 4284 * 4285 * The function can be called from anywhere including an interrupt handler. 4286 * But the function is not re-entrant, so it uses the DvcEnter/LeaveCritical() 4287 * functions to prevent reentrancy. 4288 * 4289 * Return Values: 4290 * ADV_TRUE - command completed successfully 4291 * ADV_FALSE - command failed 4292 * ADV_ERROR - command timed out 4293 */ 4294 static int 4295 AdvSendIdleCmd(ADV_DVC_VAR *asc_dvc, 4296 ushort idle_cmd, u32 idle_cmd_parameter) 4297 { 4298 int result, i, j; 4299 AdvPortAddr iop_base; 4300 4301 iop_base = asc_dvc->iop_base; 4302 4303 /* 4304 * Clear the idle command status which is set by the microcode 4305 * to a non-zero value to indicate when the command is completed. 4306 * The non-zero result is one of the IDLE_CMD_STATUS_* values 4307 */ 4308 AdvWriteWordLram(iop_base, ASC_MC_IDLE_CMD_STATUS, (ushort)0); 4309 4310 /* 4311 * Write the idle command value after the idle command parameter 4312 * has been written to avoid a race condition. If the order is not 4313 * followed, the microcode may process the idle command before the 4314 * parameters have been written to LRAM. 4315 */ 4316 AdvWriteDWordLramNoSwap(iop_base, ASC_MC_IDLE_CMD_PARAMETER, 4317 cpu_to_le32(idle_cmd_parameter)); 4318 AdvWriteWordLram(iop_base, ASC_MC_IDLE_CMD, idle_cmd); 4319 4320 /* 4321 * Tickle the RISC to tell it to process the idle command. 4322 */ 4323 AdvWriteByteRegister(iop_base, IOPB_TICKLE, ADV_TICKLE_B); 4324 if (asc_dvc->chip_type == ADV_CHIP_ASC3550) { 4325 /* 4326 * Clear the tickle value. In the ASC-3550 the RISC flag 4327 * command 'clr_tickle_b' does not work unless the host 4328 * value is cleared. 4329 */ 4330 AdvWriteByteRegister(iop_base, IOPB_TICKLE, ADV_TICKLE_NOP); 4331 } 4332 4333 /* Wait for up to 100 millisecond for the idle command to timeout. */ 4334 for (i = 0; i < SCSI_WAIT_100_MSEC; i++) { 4335 /* Poll once each microsecond for command completion. */ 4336 for (j = 0; j < SCSI_US_PER_MSEC; j++) { 4337 AdvReadWordLram(iop_base, ASC_MC_IDLE_CMD_STATUS, 4338 result); 4339 if (result != 0) 4340 return result; 4341 udelay(1); 4342 } 4343 } 4344 4345 BUG(); /* The idle command should never timeout. */ 4346 return ADV_ERROR; 4347 } 4348 4349 /* 4350 * Reset SCSI Bus and purge all outstanding requests. 4351 * 4352 * Return Value: 4353 * ADV_TRUE(1) - All requests are purged and SCSI Bus is reset. 4354 * ADV_FALSE(0) - Microcode command failed. 4355 * ADV_ERROR(-1) - Microcode command timed-out. Microcode or IC 4356 * may be hung which requires driver recovery. 4357 */ 4358 static int AdvResetSB(ADV_DVC_VAR *asc_dvc) 4359 { 4360 int status; 4361 4362 /* 4363 * Send the SCSI Bus Reset idle start idle command which asserts 4364 * the SCSI Bus Reset signal. 4365 */ 4366 status = AdvSendIdleCmd(asc_dvc, (ushort)IDLE_CMD_SCSI_RESET_START, 0L); 4367 if (status != ADV_TRUE) { 4368 return status; 4369 } 4370 4371 /* 4372 * Delay for the specified SCSI Bus Reset hold time. 4373 * 4374 * The hold time delay is done on the host because the RISC has no 4375 * microsecond accurate timer. 4376 */ 4377 udelay(ASC_SCSI_RESET_HOLD_TIME_US); 4378 4379 /* 4380 * Send the SCSI Bus Reset end idle command which de-asserts 4381 * the SCSI Bus Reset signal and purges any pending requests. 4382 */ 4383 status = AdvSendIdleCmd(asc_dvc, (ushort)IDLE_CMD_SCSI_RESET_END, 0L); 4384 if (status != ADV_TRUE) { 4385 return status; 4386 } 4387 4388 mdelay(asc_dvc->scsi_reset_wait * 1000); /* XXX: msleep? */ 4389 4390 return status; 4391 } 4392 4393 /* 4394 * Initialize the ASC-3550. 4395 * 4396 * On failure set the ADV_DVC_VAR field 'err_code' and return ADV_ERROR. 4397 * 4398 * For a non-fatal error return a warning code. If there are no warnings 4399 * then 0 is returned. 4400 * 4401 * Needed after initialization for error recovery. 4402 */ 4403 static int AdvInitAsc3550Driver(ADV_DVC_VAR *asc_dvc) 4404 { 4405 const struct firmware *fw; 4406 const char fwname[] = "advansys/3550.bin"; 4407 AdvPortAddr iop_base; 4408 ushort warn_code; 4409 int begin_addr; 4410 int end_addr; 4411 ushort code_sum; 4412 int word; 4413 int i; 4414 int err; 4415 unsigned long chksum; 4416 ushort scsi_cfg1; 4417 uchar tid; 4418 ushort bios_mem[ASC_MC_BIOSLEN / 2]; /* BIOS RISC Memory 0x40-0x8F. */ 4419 ushort wdtr_able = 0, sdtr_able, tagqng_able; 4420 uchar max_cmd[ADV_MAX_TID + 1]; 4421 4422 /* If there is already an error, don't continue. */ 4423 if (asc_dvc->err_code != 0) 4424 return ADV_ERROR; 4425 4426 /* 4427 * The caller must set 'chip_type' to ADV_CHIP_ASC3550. 4428 */ 4429 if (asc_dvc->chip_type != ADV_CHIP_ASC3550) { 4430 asc_dvc->err_code = ASC_IERR_BAD_CHIPTYPE; 4431 return ADV_ERROR; 4432 } 4433 4434 warn_code = 0; 4435 iop_base = asc_dvc->iop_base; 4436 4437 /* 4438 * Save the RISC memory BIOS region before writing the microcode. 4439 * The BIOS may already be loaded and using its RISC LRAM region 4440 * so its region must be saved and restored. 4441 * 4442 * Note: This code makes the assumption, which is currently true, 4443 * that a chip reset does not clear RISC LRAM. 4444 */ 4445 for (i = 0; i < ASC_MC_BIOSLEN / 2; i++) { 4446 AdvReadWordLram(iop_base, ASC_MC_BIOSMEM + (2 * i), 4447 bios_mem[i]); 4448 } 4449 4450 /* 4451 * Save current per TID negotiated values. 4452 */ 4453 if (bios_mem[(ASC_MC_BIOS_SIGNATURE - ASC_MC_BIOSMEM) / 2] == 0x55AA) { 4454 ushort bios_version, major, minor; 4455 4456 bios_version = 4457 bios_mem[(ASC_MC_BIOS_VERSION - ASC_MC_BIOSMEM) / 2]; 4458 major = (bios_version >> 12) & 0xF; 4459 minor = (bios_version >> 8) & 0xF; 4460 if (major < 3 || (major == 3 && minor == 1)) { 4461 /* BIOS 3.1 and earlier location of 'wdtr_able' variable. */ 4462 AdvReadWordLram(iop_base, 0x120, wdtr_able); 4463 } else { 4464 AdvReadWordLram(iop_base, ASC_MC_WDTR_ABLE, wdtr_able); 4465 } 4466 } 4467 AdvReadWordLram(iop_base, ASC_MC_SDTR_ABLE, sdtr_able); 4468 AdvReadWordLram(iop_base, ASC_MC_TAGQNG_ABLE, tagqng_able); 4469 for (tid = 0; tid <= ADV_MAX_TID; tid++) { 4470 AdvReadByteLram(iop_base, ASC_MC_NUMBER_OF_MAX_CMD + tid, 4471 max_cmd[tid]); 4472 } 4473 4474 err = request_firmware(&fw, fwname, asc_dvc->drv_ptr->dev); 4475 if (err) { 4476 printk(KERN_ERR "Failed to load image \"%s\" err %d\n", 4477 fwname, err); 4478 asc_dvc->err_code = ASC_IERR_MCODE_CHKSUM; 4479 return err; 4480 } 4481 if (fw->size < 4) { 4482 printk(KERN_ERR "Bogus length %zu in image \"%s\"\n", 4483 fw->size, fwname); 4484 release_firmware(fw); 4485 asc_dvc->err_code = ASC_IERR_MCODE_CHKSUM; 4486 return -EINVAL; 4487 } 4488 chksum = (fw->data[3] << 24) | (fw->data[2] << 16) | 4489 (fw->data[1] << 8) | fw->data[0]; 4490 asc_dvc->err_code = AdvLoadMicrocode(iop_base, &fw->data[4], 4491 fw->size - 4, ADV_3550_MEMSIZE, 4492 chksum); 4493 release_firmware(fw); 4494 if (asc_dvc->err_code) 4495 return ADV_ERROR; 4496 4497 /* 4498 * Restore the RISC memory BIOS region. 4499 */ 4500 for (i = 0; i < ASC_MC_BIOSLEN / 2; i++) { 4501 AdvWriteWordLram(iop_base, ASC_MC_BIOSMEM + (2 * i), 4502 bios_mem[i]); 4503 } 4504 4505 /* 4506 * Calculate and write the microcode code checksum to the microcode 4507 * code checksum location ASC_MC_CODE_CHK_SUM (0x2C). 4508 */ 4509 AdvReadWordLram(iop_base, ASC_MC_CODE_BEGIN_ADDR, begin_addr); 4510 AdvReadWordLram(iop_base, ASC_MC_CODE_END_ADDR, end_addr); 4511 code_sum = 0; 4512 AdvWriteWordRegister(iop_base, IOPW_RAM_ADDR, begin_addr); 4513 for (word = begin_addr; word < end_addr; word += 2) { 4514 code_sum += AdvReadWordAutoIncLram(iop_base); 4515 } 4516 AdvWriteWordLram(iop_base, ASC_MC_CODE_CHK_SUM, code_sum); 4517 4518 /* 4519 * Read and save microcode version and date. 4520 */ 4521 AdvReadWordLram(iop_base, ASC_MC_VERSION_DATE, 4522 asc_dvc->cfg->mcode_date); 4523 AdvReadWordLram(iop_base, ASC_MC_VERSION_NUM, 4524 asc_dvc->cfg->mcode_version); 4525 4526 /* 4527 * Set the chip type to indicate the ASC3550. 4528 */ 4529 AdvWriteWordLram(iop_base, ASC_MC_CHIP_TYPE, ADV_CHIP_ASC3550); 4530 4531 /* 4532 * If the PCI Configuration Command Register "Parity Error Response 4533 * Control" Bit was clear (0), then set the microcode variable 4534 * 'control_flag' CONTROL_FLAG_IGNORE_PERR flag to tell the microcode 4535 * to ignore DMA parity errors. 4536 */ 4537 if (asc_dvc->cfg->control_flag & CONTROL_FLAG_IGNORE_PERR) { 4538 AdvReadWordLram(iop_base, ASC_MC_CONTROL_FLAG, word); 4539 word |= CONTROL_FLAG_IGNORE_PERR; 4540 AdvWriteWordLram(iop_base, ASC_MC_CONTROL_FLAG, word); 4541 } 4542 4543 /* 4544 * For ASC-3550, setting the START_CTL_EMFU [3:2] bits sets a FIFO 4545 * threshold of 128 bytes. This register is only accessible to the host. 4546 */ 4547 AdvWriteByteRegister(iop_base, IOPB_DMA_CFG0, 4548 START_CTL_EMFU | READ_CMD_MRM); 4549 4550 /* 4551 * Microcode operating variables for WDTR, SDTR, and command tag 4552 * queuing will be set in slave_configure() based on what a 4553 * device reports it is capable of in Inquiry byte 7. 4554 * 4555 * If SCSI Bus Resets have been disabled, then directly set 4556 * SDTR and WDTR from the EEPROM configuration. This will allow 4557 * the BIOS and warm boot to work without a SCSI bus hang on 4558 * the Inquiry caused by host and target mismatched DTR values. 4559 * Without the SCSI Bus Reset, before an Inquiry a device can't 4560 * be assumed to be in Asynchronous, Narrow mode. 4561 */ 4562 if ((asc_dvc->bios_ctrl & BIOS_CTRL_RESET_SCSI_BUS) == 0) { 4563 AdvWriteWordLram(iop_base, ASC_MC_WDTR_ABLE, 4564 asc_dvc->wdtr_able); 4565 AdvWriteWordLram(iop_base, ASC_MC_SDTR_ABLE, 4566 asc_dvc->sdtr_able); 4567 } 4568 4569 /* 4570 * Set microcode operating variables for SDTR_SPEED1, SDTR_SPEED2, 4571 * SDTR_SPEED3, and SDTR_SPEED4 based on the ULTRA EEPROM per TID 4572 * bitmask. These values determine the maximum SDTR speed negotiated 4573 * with a device. 4574 * 4575 * The SDTR per TID bitmask overrides the SDTR_SPEED1, SDTR_SPEED2, 4576 * SDTR_SPEED3, and SDTR_SPEED4 values so it is safe to set them 4577 * without determining here whether the device supports SDTR. 4578 * 4579 * 4-bit speed SDTR speed name 4580 * =========== =============== 4581 * 0000b (0x0) SDTR disabled 4582 * 0001b (0x1) 5 Mhz 4583 * 0010b (0x2) 10 Mhz 4584 * 0011b (0x3) 20 Mhz (Ultra) 4585 * 0100b (0x4) 40 Mhz (LVD/Ultra2) 4586 * 0101b (0x5) 80 Mhz (LVD2/Ultra3) 4587 * 0110b (0x6) Undefined 4588 * . 4589 * 1111b (0xF) Undefined 4590 */ 4591 word = 0; 4592 for (tid = 0; tid <= ADV_MAX_TID; tid++) { 4593 if (ADV_TID_TO_TIDMASK(tid) & asc_dvc->ultra_able) { 4594 /* Set Ultra speed for TID 'tid'. */ 4595 word |= (0x3 << (4 * (tid % 4))); 4596 } else { 4597 /* Set Fast speed for TID 'tid'. */ 4598 word |= (0x2 << (4 * (tid % 4))); 4599 } 4600 if (tid == 3) { /* Check if done with sdtr_speed1. */ 4601 AdvWriteWordLram(iop_base, ASC_MC_SDTR_SPEED1, word); 4602 word = 0; 4603 } else if (tid == 7) { /* Check if done with sdtr_speed2. */ 4604 AdvWriteWordLram(iop_base, ASC_MC_SDTR_SPEED2, word); 4605 word = 0; 4606 } else if (tid == 11) { /* Check if done with sdtr_speed3. */ 4607 AdvWriteWordLram(iop_base, ASC_MC_SDTR_SPEED3, word); 4608 word = 0; 4609 } else if (tid == 15) { /* Check if done with sdtr_speed4. */ 4610 AdvWriteWordLram(iop_base, ASC_MC_SDTR_SPEED4, word); 4611 /* End of loop. */ 4612 } 4613 } 4614 4615 /* 4616 * Set microcode operating variable for the disconnect per TID bitmask. 4617 */ 4618 AdvWriteWordLram(iop_base, ASC_MC_DISC_ENABLE, 4619 asc_dvc->cfg->disc_enable); 4620 4621 /* 4622 * Set SCSI_CFG0 Microcode Default Value. 4623 * 4624 * The microcode will set the SCSI_CFG0 register using this value 4625 * after it is started below. 4626 */ 4627 AdvWriteWordLram(iop_base, ASC_MC_DEFAULT_SCSI_CFG0, 4628 PARITY_EN | QUEUE_128 | SEL_TMO_LONG | OUR_ID_EN | 4629 asc_dvc->chip_scsi_id); 4630 4631 /* 4632 * Determine SCSI_CFG1 Microcode Default Value. 4633 * 4634 * The microcode will set the SCSI_CFG1 register using this value 4635 * after it is started below. 4636 */ 4637 4638 /* Read current SCSI_CFG1 Register value. */ 4639 scsi_cfg1 = AdvReadWordRegister(iop_base, IOPW_SCSI_CFG1); 4640 4641 /* 4642 * If all three connectors are in use, return an error. 4643 */ 4644 if ((scsi_cfg1 & CABLE_ILLEGAL_A) == 0 || 4645 (scsi_cfg1 & CABLE_ILLEGAL_B) == 0) { 4646 asc_dvc->err_code |= ASC_IERR_ILLEGAL_CONNECTION; 4647 return ADV_ERROR; 4648 } 4649 4650 /* 4651 * If the internal narrow cable is reversed all of the SCSI_CTRL 4652 * register signals will be set. Check for and return an error if 4653 * this condition is found. 4654 */ 4655 if ((AdvReadWordRegister(iop_base, IOPW_SCSI_CTRL) & 0x3F07) == 0x3F07) { 4656 asc_dvc->err_code |= ASC_IERR_REVERSED_CABLE; 4657 return ADV_ERROR; 4658 } 4659 4660 /* 4661 * If this is a differential board and a single-ended device 4662 * is attached to one of the connectors, return an error. 4663 */ 4664 if ((scsi_cfg1 & DIFF_MODE) && (scsi_cfg1 & DIFF_SENSE) == 0) { 4665 asc_dvc->err_code |= ASC_IERR_SINGLE_END_DEVICE; 4666 return ADV_ERROR; 4667 } 4668 4669 /* 4670 * If automatic termination control is enabled, then set the 4671 * termination value based on a table listed in a_condor.h. 4672 * 4673 * If manual termination was specified with an EEPROM setting 4674 * then 'termination' was set-up in AdvInitFrom3550EEPROM() and 4675 * is ready to be 'ored' into SCSI_CFG1. 4676 */ 4677 if (asc_dvc->cfg->termination == 0) { 4678 /* 4679 * The software always controls termination by setting TERM_CTL_SEL. 4680 * If TERM_CTL_SEL were set to 0, the hardware would set termination. 4681 */ 4682 asc_dvc->cfg->termination |= TERM_CTL_SEL; 4683 4684 switch (scsi_cfg1 & CABLE_DETECT) { 4685 /* TERM_CTL_H: on, TERM_CTL_L: on */ 4686 case 0x3: 4687 case 0x7: 4688 case 0xB: 4689 case 0xD: 4690 case 0xE: 4691 case 0xF: 4692 asc_dvc->cfg->termination |= (TERM_CTL_H | TERM_CTL_L); 4693 break; 4694 4695 /* TERM_CTL_H: on, TERM_CTL_L: off */ 4696 case 0x1: 4697 case 0x5: 4698 case 0x9: 4699 case 0xA: 4700 case 0xC: 4701 asc_dvc->cfg->termination |= TERM_CTL_H; 4702 break; 4703 4704 /* TERM_CTL_H: off, TERM_CTL_L: off */ 4705 case 0x2: 4706 case 0x6: 4707 break; 4708 } 4709 } 4710 4711 /* 4712 * Clear any set TERM_CTL_H and TERM_CTL_L bits. 4713 */ 4714 scsi_cfg1 &= ~TERM_CTL; 4715 4716 /* 4717 * Invert the TERM_CTL_H and TERM_CTL_L bits and then 4718 * set 'scsi_cfg1'. The TERM_POL bit does not need to be 4719 * referenced, because the hardware internally inverts 4720 * the Termination High and Low bits if TERM_POL is set. 4721 */ 4722 scsi_cfg1 |= (TERM_CTL_SEL | (~asc_dvc->cfg->termination & TERM_CTL)); 4723 4724 /* 4725 * Set SCSI_CFG1 Microcode Default Value 4726 * 4727 * Set filter value and possibly modified termination control 4728 * bits in the Microcode SCSI_CFG1 Register Value. 4729 * 4730 * The microcode will set the SCSI_CFG1 register using this value 4731 * after it is started below. 4732 */ 4733 AdvWriteWordLram(iop_base, ASC_MC_DEFAULT_SCSI_CFG1, 4734 FLTR_DISABLE | scsi_cfg1); 4735 4736 /* 4737 * Set MEM_CFG Microcode Default Value 4738 * 4739 * The microcode will set the MEM_CFG register using this value 4740 * after it is started below. 4741 * 4742 * MEM_CFG may be accessed as a word or byte, but only bits 0-7 4743 * are defined. 4744 * 4745 * ASC-3550 has 8KB internal memory. 4746 */ 4747 AdvWriteWordLram(iop_base, ASC_MC_DEFAULT_MEM_CFG, 4748 BIOS_EN | RAM_SZ_8KB); 4749 4750 /* 4751 * Set SEL_MASK Microcode Default Value 4752 * 4753 * The microcode will set the SEL_MASK register using this value 4754 * after it is started below. 4755 */ 4756 AdvWriteWordLram(iop_base, ASC_MC_DEFAULT_SEL_MASK, 4757 ADV_TID_TO_TIDMASK(asc_dvc->chip_scsi_id)); 4758 4759 AdvBuildCarrierFreelist(asc_dvc); 4760 4761 /* 4762 * Set-up the Host->RISC Initiator Command Queue (ICQ). 4763 */ 4764 4765 asc_dvc->icq_sp = adv_get_next_carrier(asc_dvc); 4766 if (!asc_dvc->icq_sp) { 4767 asc_dvc->err_code |= ASC_IERR_NO_CARRIER; 4768 return ADV_ERROR; 4769 } 4770 4771 /* 4772 * Set RISC ICQ physical address start value. 4773 */ 4774 AdvWriteDWordLramNoSwap(iop_base, ASC_MC_ICQ, asc_dvc->icq_sp->carr_pa); 4775 4776 /* 4777 * Set-up the RISC->Host Initiator Response Queue (IRQ). 4778 */ 4779 asc_dvc->irq_sp = adv_get_next_carrier(asc_dvc); 4780 if (!asc_dvc->irq_sp) { 4781 asc_dvc->err_code |= ASC_IERR_NO_CARRIER; 4782 return ADV_ERROR; 4783 } 4784 4785 /* 4786 * Set RISC IRQ physical address start value. 4787 */ 4788 AdvWriteDWordLramNoSwap(iop_base, ASC_MC_IRQ, asc_dvc->irq_sp->carr_pa); 4789 asc_dvc->carr_pending_cnt = 0; 4790 4791 AdvWriteByteRegister(iop_base, IOPB_INTR_ENABLES, 4792 (ADV_INTR_ENABLE_HOST_INTR | 4793 ADV_INTR_ENABLE_GLOBAL_INTR)); 4794 4795 AdvReadWordLram(iop_base, ASC_MC_CODE_BEGIN_ADDR, word); 4796 AdvWriteWordRegister(iop_base, IOPW_PC, word); 4797 4798 /* finally, finally, gentlemen, start your engine */ 4799 AdvWriteWordRegister(iop_base, IOPW_RISC_CSR, ADV_RISC_CSR_RUN); 4800 4801 /* 4802 * Reset the SCSI Bus if the EEPROM indicates that SCSI Bus 4803 * Resets should be performed. The RISC has to be running 4804 * to issue a SCSI Bus Reset. 4805 */ 4806 if (asc_dvc->bios_ctrl & BIOS_CTRL_RESET_SCSI_BUS) { 4807 /* 4808 * If the BIOS Signature is present in memory, restore the 4809 * BIOS Handshake Configuration Table and do not perform 4810 * a SCSI Bus Reset. 4811 */ 4812 if (bios_mem[(ASC_MC_BIOS_SIGNATURE - ASC_MC_BIOSMEM) / 2] == 4813 0x55AA) { 4814 /* 4815 * Restore per TID negotiated values. 4816 */ 4817 AdvWriteWordLram(iop_base, ASC_MC_WDTR_ABLE, wdtr_able); 4818 AdvWriteWordLram(iop_base, ASC_MC_SDTR_ABLE, sdtr_able); 4819 AdvWriteWordLram(iop_base, ASC_MC_TAGQNG_ABLE, 4820 tagqng_able); 4821 for (tid = 0; tid <= ADV_MAX_TID; tid++) { 4822 AdvWriteByteLram(iop_base, 4823 ASC_MC_NUMBER_OF_MAX_CMD + tid, 4824 max_cmd[tid]); 4825 } 4826 } else { 4827 if (AdvResetSB(asc_dvc) != ADV_TRUE) { 4828 warn_code = ASC_WARN_BUSRESET_ERROR; 4829 } 4830 } 4831 } 4832 4833 return warn_code; 4834 } 4835 4836 /* 4837 * Initialize the ASC-38C0800. 4838 * 4839 * On failure set the ADV_DVC_VAR field 'err_code' and return ADV_ERROR. 4840 * 4841 * For a non-fatal error return a warning code. If there are no warnings 4842 * then 0 is returned. 4843 * 4844 * Needed after initialization for error recovery. 4845 */ 4846 static int AdvInitAsc38C0800Driver(ADV_DVC_VAR *asc_dvc) 4847 { 4848 const struct firmware *fw; 4849 const char fwname[] = "advansys/38C0800.bin"; 4850 AdvPortAddr iop_base; 4851 ushort warn_code; 4852 int begin_addr; 4853 int end_addr; 4854 ushort code_sum; 4855 int word; 4856 int i; 4857 int err; 4858 unsigned long chksum; 4859 ushort scsi_cfg1; 4860 uchar byte; 4861 uchar tid; 4862 ushort bios_mem[ASC_MC_BIOSLEN / 2]; /* BIOS RISC Memory 0x40-0x8F. */ 4863 ushort wdtr_able, sdtr_able, tagqng_able; 4864 uchar max_cmd[ADV_MAX_TID + 1]; 4865 4866 /* If there is already an error, don't continue. */ 4867 if (asc_dvc->err_code != 0) 4868 return ADV_ERROR; 4869 4870 /* 4871 * The caller must set 'chip_type' to ADV_CHIP_ASC38C0800. 4872 */ 4873 if (asc_dvc->chip_type != ADV_CHIP_ASC38C0800) { 4874 asc_dvc->err_code = ASC_IERR_BAD_CHIPTYPE; 4875 return ADV_ERROR; 4876 } 4877 4878 warn_code = 0; 4879 iop_base = asc_dvc->iop_base; 4880 4881 /* 4882 * Save the RISC memory BIOS region before writing the microcode. 4883 * The BIOS may already be loaded and using its RISC LRAM region 4884 * so its region must be saved and restored. 4885 * 4886 * Note: This code makes the assumption, which is currently true, 4887 * that a chip reset does not clear RISC LRAM. 4888 */ 4889 for (i = 0; i < ASC_MC_BIOSLEN / 2; i++) { 4890 AdvReadWordLram(iop_base, ASC_MC_BIOSMEM + (2 * i), 4891 bios_mem[i]); 4892 } 4893 4894 /* 4895 * Save current per TID negotiated values. 4896 */ 4897 AdvReadWordLram(iop_base, ASC_MC_WDTR_ABLE, wdtr_able); 4898 AdvReadWordLram(iop_base, ASC_MC_SDTR_ABLE, sdtr_able); 4899 AdvReadWordLram(iop_base, ASC_MC_TAGQNG_ABLE, tagqng_able); 4900 for (tid = 0; tid <= ADV_MAX_TID; tid++) { 4901 AdvReadByteLram(iop_base, ASC_MC_NUMBER_OF_MAX_CMD + tid, 4902 max_cmd[tid]); 4903 } 4904 4905 /* 4906 * RAM BIST (RAM Built-In Self Test) 4907 * 4908 * Address : I/O base + offset 0x38h register (byte). 4909 * Function: Bit 7-6(RW) : RAM mode 4910 * Normal Mode : 0x00 4911 * Pre-test Mode : 0x40 4912 * RAM Test Mode : 0x80 4913 * Bit 5 : unused 4914 * Bit 4(RO) : Done bit 4915 * Bit 3-0(RO) : Status 4916 * Host Error : 0x08 4917 * Int_RAM Error : 0x04 4918 * RISC Error : 0x02 4919 * SCSI Error : 0x01 4920 * No Error : 0x00 4921 * 4922 * Note: RAM BIST code should be put right here, before loading the 4923 * microcode and after saving the RISC memory BIOS region. 4924 */ 4925 4926 /* 4927 * LRAM Pre-test 4928 * 4929 * Write PRE_TEST_MODE (0x40) to register and wait for 10 milliseconds. 4930 * If Done bit not set or low nibble not PRE_TEST_VALUE (0x05), return 4931 * an error. Reset to NORMAL_MODE (0x00) and do again. If cannot reset 4932 * to NORMAL_MODE, return an error too. 4933 */ 4934 for (i = 0; i < 2; i++) { 4935 AdvWriteByteRegister(iop_base, IOPB_RAM_BIST, PRE_TEST_MODE); 4936 mdelay(10); /* Wait for 10ms before reading back. */ 4937 byte = AdvReadByteRegister(iop_base, IOPB_RAM_BIST); 4938 if ((byte & RAM_TEST_DONE) == 0 4939 || (byte & 0x0F) != PRE_TEST_VALUE) { 4940 asc_dvc->err_code = ASC_IERR_BIST_PRE_TEST; 4941 return ADV_ERROR; 4942 } 4943 4944 AdvWriteByteRegister(iop_base, IOPB_RAM_BIST, NORMAL_MODE); 4945 mdelay(10); /* Wait for 10ms before reading back. */ 4946 if (AdvReadByteRegister(iop_base, IOPB_RAM_BIST) 4947 != NORMAL_VALUE) { 4948 asc_dvc->err_code = ASC_IERR_BIST_PRE_TEST; 4949 return ADV_ERROR; 4950 } 4951 } 4952 4953 /* 4954 * LRAM Test - It takes about 1.5 ms to run through the test. 4955 * 4956 * Write RAM_TEST_MODE (0x80) to register and wait for 10 milliseconds. 4957 * If Done bit not set or Status not 0, save register byte, set the 4958 * err_code, and return an error. 4959 */ 4960 AdvWriteByteRegister(iop_base, IOPB_RAM_BIST, RAM_TEST_MODE); 4961 mdelay(10); /* Wait for 10ms before checking status. */ 4962 4963 byte = AdvReadByteRegister(iop_base, IOPB_RAM_BIST); 4964 if ((byte & RAM_TEST_DONE) == 0 || (byte & RAM_TEST_STATUS) != 0) { 4965 /* Get here if Done bit not set or Status not 0. */ 4966 asc_dvc->bist_err_code = byte; /* for BIOS display message */ 4967 asc_dvc->err_code = ASC_IERR_BIST_RAM_TEST; 4968 return ADV_ERROR; 4969 } 4970 4971 /* We need to reset back to normal mode after LRAM test passes. */ 4972 AdvWriteByteRegister(iop_base, IOPB_RAM_BIST, NORMAL_MODE); 4973 4974 err = request_firmware(&fw, fwname, asc_dvc->drv_ptr->dev); 4975 if (err) { 4976 printk(KERN_ERR "Failed to load image \"%s\" err %d\n", 4977 fwname, err); 4978 asc_dvc->err_code = ASC_IERR_MCODE_CHKSUM; 4979 return err; 4980 } 4981 if (fw->size < 4) { 4982 printk(KERN_ERR "Bogus length %zu in image \"%s\"\n", 4983 fw->size, fwname); 4984 release_firmware(fw); 4985 asc_dvc->err_code = ASC_IERR_MCODE_CHKSUM; 4986 return -EINVAL; 4987 } 4988 chksum = (fw->data[3] << 24) | (fw->data[2] << 16) | 4989 (fw->data[1] << 8) | fw->data[0]; 4990 asc_dvc->err_code = AdvLoadMicrocode(iop_base, &fw->data[4], 4991 fw->size - 4, ADV_38C0800_MEMSIZE, 4992 chksum); 4993 release_firmware(fw); 4994 if (asc_dvc->err_code) 4995 return ADV_ERROR; 4996 4997 /* 4998 * Restore the RISC memory BIOS region. 4999 */ 5000 for (i = 0; i < ASC_MC_BIOSLEN / 2; i++) { 5001 AdvWriteWordLram(iop_base, ASC_MC_BIOSMEM + (2 * i), 5002 bios_mem[i]); 5003 } 5004 5005 /* 5006 * Calculate and write the microcode code checksum to the microcode 5007 * code checksum location ASC_MC_CODE_CHK_SUM (0x2C). 5008 */ 5009 AdvReadWordLram(iop_base, ASC_MC_CODE_BEGIN_ADDR, begin_addr); 5010 AdvReadWordLram(iop_base, ASC_MC_CODE_END_ADDR, end_addr); 5011 code_sum = 0; 5012 AdvWriteWordRegister(iop_base, IOPW_RAM_ADDR, begin_addr); 5013 for (word = begin_addr; word < end_addr; word += 2) { 5014 code_sum += AdvReadWordAutoIncLram(iop_base); 5015 } 5016 AdvWriteWordLram(iop_base, ASC_MC_CODE_CHK_SUM, code_sum); 5017 5018 /* 5019 * Read microcode version and date. 5020 */ 5021 AdvReadWordLram(iop_base, ASC_MC_VERSION_DATE, 5022 asc_dvc->cfg->mcode_date); 5023 AdvReadWordLram(iop_base, ASC_MC_VERSION_NUM, 5024 asc_dvc->cfg->mcode_version); 5025 5026 /* 5027 * Set the chip type to indicate the ASC38C0800. 5028 */ 5029 AdvWriteWordLram(iop_base, ASC_MC_CHIP_TYPE, ADV_CHIP_ASC38C0800); 5030 5031 /* 5032 * Write 1 to bit 14 'DIS_TERM_DRV' in the SCSI_CFG1 register. 5033 * When DIS_TERM_DRV set to 1, C_DET[3:0] will reflect current 5034 * cable detection and then we are able to read C_DET[3:0]. 5035 * 5036 * Note: We will reset DIS_TERM_DRV to 0 in the 'Set SCSI_CFG1 5037 * Microcode Default Value' section below. 5038 */ 5039 scsi_cfg1 = AdvReadWordRegister(iop_base, IOPW_SCSI_CFG1); 5040 AdvWriteWordRegister(iop_base, IOPW_SCSI_CFG1, 5041 scsi_cfg1 | DIS_TERM_DRV); 5042 5043 /* 5044 * If the PCI Configuration Command Register "Parity Error Response 5045 * Control" Bit was clear (0), then set the microcode variable 5046 * 'control_flag' CONTROL_FLAG_IGNORE_PERR flag to tell the microcode 5047 * to ignore DMA parity errors. 5048 */ 5049 if (asc_dvc->cfg->control_flag & CONTROL_FLAG_IGNORE_PERR) { 5050 AdvReadWordLram(iop_base, ASC_MC_CONTROL_FLAG, word); 5051 word |= CONTROL_FLAG_IGNORE_PERR; 5052 AdvWriteWordLram(iop_base, ASC_MC_CONTROL_FLAG, word); 5053 } 5054 5055 /* 5056 * For ASC-38C0800, set FIFO_THRESH_80B [6:4] bits and START_CTL_TH [3:2] 5057 * bits for the default FIFO threshold. 5058 * 5059 * Note: ASC-38C0800 FIFO threshold has been changed to 256 bytes. 5060 * 5061 * For DMA Errata #4 set the BC_THRESH_ENB bit. 5062 */ 5063 AdvWriteByteRegister(iop_base, IOPB_DMA_CFG0, 5064 BC_THRESH_ENB | FIFO_THRESH_80B | START_CTL_TH | 5065 READ_CMD_MRM); 5066 5067 /* 5068 * Microcode operating variables for WDTR, SDTR, and command tag 5069 * queuing will be set in slave_configure() based on what a 5070 * device reports it is capable of in Inquiry byte 7. 5071 * 5072 * If SCSI Bus Resets have been disabled, then directly set 5073 * SDTR and WDTR from the EEPROM configuration. This will allow 5074 * the BIOS and warm boot to work without a SCSI bus hang on 5075 * the Inquiry caused by host and target mismatched DTR values. 5076 * Without the SCSI Bus Reset, before an Inquiry a device can't 5077 * be assumed to be in Asynchronous, Narrow mode. 5078 */ 5079 if ((asc_dvc->bios_ctrl & BIOS_CTRL_RESET_SCSI_BUS) == 0) { 5080 AdvWriteWordLram(iop_base, ASC_MC_WDTR_ABLE, 5081 asc_dvc->wdtr_able); 5082 AdvWriteWordLram(iop_base, ASC_MC_SDTR_ABLE, 5083 asc_dvc->sdtr_able); 5084 } 5085 5086 /* 5087 * Set microcode operating variables for DISC and SDTR_SPEED1, 5088 * SDTR_SPEED2, SDTR_SPEED3, and SDTR_SPEED4 based on the EEPROM 5089 * configuration values. 5090 * 5091 * The SDTR per TID bitmask overrides the SDTR_SPEED1, SDTR_SPEED2, 5092 * SDTR_SPEED3, and SDTR_SPEED4 values so it is safe to set them 5093 * without determining here whether the device supports SDTR. 5094 */ 5095 AdvWriteWordLram(iop_base, ASC_MC_DISC_ENABLE, 5096 asc_dvc->cfg->disc_enable); 5097 AdvWriteWordLram(iop_base, ASC_MC_SDTR_SPEED1, asc_dvc->sdtr_speed1); 5098 AdvWriteWordLram(iop_base, ASC_MC_SDTR_SPEED2, asc_dvc->sdtr_speed2); 5099 AdvWriteWordLram(iop_base, ASC_MC_SDTR_SPEED3, asc_dvc->sdtr_speed3); 5100 AdvWriteWordLram(iop_base, ASC_MC_SDTR_SPEED4, asc_dvc->sdtr_speed4); 5101 5102 /* 5103 * Set SCSI_CFG0 Microcode Default Value. 5104 * 5105 * The microcode will set the SCSI_CFG0 register using this value 5106 * after it is started below. 5107 */ 5108 AdvWriteWordLram(iop_base, ASC_MC_DEFAULT_SCSI_CFG0, 5109 PARITY_EN | QUEUE_128 | SEL_TMO_LONG | OUR_ID_EN | 5110 asc_dvc->chip_scsi_id); 5111 5112 /* 5113 * Determine SCSI_CFG1 Microcode Default Value. 5114 * 5115 * The microcode will set the SCSI_CFG1 register using this value 5116 * after it is started below. 5117 */ 5118 5119 /* Read current SCSI_CFG1 Register value. */ 5120 scsi_cfg1 = AdvReadWordRegister(iop_base, IOPW_SCSI_CFG1); 5121 5122 /* 5123 * If the internal narrow cable is reversed all of the SCSI_CTRL 5124 * register signals will be set. Check for and return an error if 5125 * this condition is found. 5126 */ 5127 if ((AdvReadWordRegister(iop_base, IOPW_SCSI_CTRL) & 0x3F07) == 0x3F07) { 5128 asc_dvc->err_code |= ASC_IERR_REVERSED_CABLE; 5129 return ADV_ERROR; 5130 } 5131 5132 /* 5133 * All kind of combinations of devices attached to one of four 5134 * connectors are acceptable except HVD device attached. For example, 5135 * LVD device can be attached to SE connector while SE device attached 5136 * to LVD connector. If LVD device attached to SE connector, it only 5137 * runs up to Ultra speed. 5138 * 5139 * If an HVD device is attached to one of LVD connectors, return an 5140 * error. However, there is no way to detect HVD device attached to 5141 * SE connectors. 5142 */ 5143 if (scsi_cfg1 & HVD) { 5144 asc_dvc->err_code = ASC_IERR_HVD_DEVICE; 5145 return ADV_ERROR; 5146 } 5147 5148 /* 5149 * If either SE or LVD automatic termination control is enabled, then 5150 * set the termination value based on a table listed in a_condor.h. 5151 * 5152 * If manual termination was specified with an EEPROM setting then 5153 * 'termination' was set-up in AdvInitFrom38C0800EEPROM() and is ready 5154 * to be 'ored' into SCSI_CFG1. 5155 */ 5156 if ((asc_dvc->cfg->termination & TERM_SE) == 0) { 5157 /* SE automatic termination control is enabled. */ 5158 switch (scsi_cfg1 & C_DET_SE) { 5159 /* TERM_SE_HI: on, TERM_SE_LO: on */ 5160 case 0x1: 5161 case 0x2: 5162 case 0x3: 5163 asc_dvc->cfg->termination |= TERM_SE; 5164 break; 5165 5166 /* TERM_SE_HI: on, TERM_SE_LO: off */ 5167 case 0x0: 5168 asc_dvc->cfg->termination |= TERM_SE_HI; 5169 break; 5170 } 5171 } 5172 5173 if ((asc_dvc->cfg->termination & TERM_LVD) == 0) { 5174 /* LVD automatic termination control is enabled. */ 5175 switch (scsi_cfg1 & C_DET_LVD) { 5176 /* TERM_LVD_HI: on, TERM_LVD_LO: on */ 5177 case 0x4: 5178 case 0x8: 5179 case 0xC: 5180 asc_dvc->cfg->termination |= TERM_LVD; 5181 break; 5182 5183 /* TERM_LVD_HI: off, TERM_LVD_LO: off */ 5184 case 0x0: 5185 break; 5186 } 5187 } 5188 5189 /* 5190 * Clear any set TERM_SE and TERM_LVD bits. 5191 */ 5192 scsi_cfg1 &= (~TERM_SE & ~TERM_LVD); 5193 5194 /* 5195 * Invert the TERM_SE and TERM_LVD bits and then set 'scsi_cfg1'. 5196 */ 5197 scsi_cfg1 |= (~asc_dvc->cfg->termination & 0xF0); 5198 5199 /* 5200 * Clear BIG_ENDIAN, DIS_TERM_DRV, Terminator Polarity and HVD/LVD/SE 5201 * bits and set possibly modified termination control bits in the 5202 * Microcode SCSI_CFG1 Register Value. 5203 */ 5204 scsi_cfg1 &= (~BIG_ENDIAN & ~DIS_TERM_DRV & ~TERM_POL & ~HVD_LVD_SE); 5205 5206 /* 5207 * Set SCSI_CFG1 Microcode Default Value 5208 * 5209 * Set possibly modified termination control and reset DIS_TERM_DRV 5210 * bits in the Microcode SCSI_CFG1 Register Value. 5211 * 5212 * The microcode will set the SCSI_CFG1 register using this value 5213 * after it is started below. 5214 */ 5215 AdvWriteWordLram(iop_base, ASC_MC_DEFAULT_SCSI_CFG1, scsi_cfg1); 5216 5217 /* 5218 * Set MEM_CFG Microcode Default Value 5219 * 5220 * The microcode will set the MEM_CFG register using this value 5221 * after it is started below. 5222 * 5223 * MEM_CFG may be accessed as a word or byte, but only bits 0-7 5224 * are defined. 5225 * 5226 * ASC-38C0800 has 16KB internal memory. 5227 */ 5228 AdvWriteWordLram(iop_base, ASC_MC_DEFAULT_MEM_CFG, 5229 BIOS_EN | RAM_SZ_16KB); 5230 5231 /* 5232 * Set SEL_MASK Microcode Default Value 5233 * 5234 * The microcode will set the SEL_MASK register using this value 5235 * after it is started below. 5236 */ 5237 AdvWriteWordLram(iop_base, ASC_MC_DEFAULT_SEL_MASK, 5238 ADV_TID_TO_TIDMASK(asc_dvc->chip_scsi_id)); 5239 5240 AdvBuildCarrierFreelist(asc_dvc); 5241 5242 /* 5243 * Set-up the Host->RISC Initiator Command Queue (ICQ). 5244 */ 5245 5246 asc_dvc->icq_sp = adv_get_next_carrier(asc_dvc); 5247 if (!asc_dvc->icq_sp) { 5248 ASC_DBG(0, "Failed to get ICQ carrier\n"); 5249 asc_dvc->err_code |= ASC_IERR_NO_CARRIER; 5250 return ADV_ERROR; 5251 } 5252 5253 /* 5254 * Set RISC ICQ physical address start value. 5255 * carr_pa is LE, must be native before write 5256 */ 5257 AdvWriteDWordLramNoSwap(iop_base, ASC_MC_ICQ, asc_dvc->icq_sp->carr_pa); 5258 5259 /* 5260 * Set-up the RISC->Host Initiator Response Queue (IRQ). 5261 */ 5262 asc_dvc->irq_sp = adv_get_next_carrier(asc_dvc); 5263 if (!asc_dvc->irq_sp) { 5264 ASC_DBG(0, "Failed to get IRQ carrier\n"); 5265 asc_dvc->err_code |= ASC_IERR_NO_CARRIER; 5266 return ADV_ERROR; 5267 } 5268 5269 /* 5270 * Set RISC IRQ physical address start value. 5271 * 5272 * carr_pa is LE, must be native before write * 5273 */ 5274 AdvWriteDWordLramNoSwap(iop_base, ASC_MC_IRQ, asc_dvc->irq_sp->carr_pa); 5275 asc_dvc->carr_pending_cnt = 0; 5276 5277 AdvWriteByteRegister(iop_base, IOPB_INTR_ENABLES, 5278 (ADV_INTR_ENABLE_HOST_INTR | 5279 ADV_INTR_ENABLE_GLOBAL_INTR)); 5280 5281 AdvReadWordLram(iop_base, ASC_MC_CODE_BEGIN_ADDR, word); 5282 AdvWriteWordRegister(iop_base, IOPW_PC, word); 5283 5284 /* finally, finally, gentlemen, start your engine */ 5285 AdvWriteWordRegister(iop_base, IOPW_RISC_CSR, ADV_RISC_CSR_RUN); 5286 5287 /* 5288 * Reset the SCSI Bus if the EEPROM indicates that SCSI Bus 5289 * Resets should be performed. The RISC has to be running 5290 * to issue a SCSI Bus Reset. 5291 */ 5292 if (asc_dvc->bios_ctrl & BIOS_CTRL_RESET_SCSI_BUS) { 5293 /* 5294 * If the BIOS Signature is present in memory, restore the 5295 * BIOS Handshake Configuration Table and do not perform 5296 * a SCSI Bus Reset. 5297 */ 5298 if (bios_mem[(ASC_MC_BIOS_SIGNATURE - ASC_MC_BIOSMEM) / 2] == 5299 0x55AA) { 5300 /* 5301 * Restore per TID negotiated values. 5302 */ 5303 AdvWriteWordLram(iop_base, ASC_MC_WDTR_ABLE, wdtr_able); 5304 AdvWriteWordLram(iop_base, ASC_MC_SDTR_ABLE, sdtr_able); 5305 AdvWriteWordLram(iop_base, ASC_MC_TAGQNG_ABLE, 5306 tagqng_able); 5307 for (tid = 0; tid <= ADV_MAX_TID; tid++) { 5308 AdvWriteByteLram(iop_base, 5309 ASC_MC_NUMBER_OF_MAX_CMD + tid, 5310 max_cmd[tid]); 5311 } 5312 } else { 5313 if (AdvResetSB(asc_dvc) != ADV_TRUE) { 5314 warn_code = ASC_WARN_BUSRESET_ERROR; 5315 } 5316 } 5317 } 5318 5319 return warn_code; 5320 } 5321 5322 /* 5323 * Initialize the ASC-38C1600. 5324 * 5325 * On failure set the ASC_DVC_VAR field 'err_code' and return ADV_ERROR. 5326 * 5327 * For a non-fatal error return a warning code. If there are no warnings 5328 * then 0 is returned. 5329 * 5330 * Needed after initialization for error recovery. 5331 */ 5332 static int AdvInitAsc38C1600Driver(ADV_DVC_VAR *asc_dvc) 5333 { 5334 const struct firmware *fw; 5335 const char fwname[] = "advansys/38C1600.bin"; 5336 AdvPortAddr iop_base; 5337 ushort warn_code; 5338 int begin_addr; 5339 int end_addr; 5340 ushort code_sum; 5341 long word; 5342 int i; 5343 int err; 5344 unsigned long chksum; 5345 ushort scsi_cfg1; 5346 uchar byte; 5347 uchar tid; 5348 ushort bios_mem[ASC_MC_BIOSLEN / 2]; /* BIOS RISC Memory 0x40-0x8F. */ 5349 ushort wdtr_able, sdtr_able, ppr_able, tagqng_able; 5350 uchar max_cmd[ASC_MAX_TID + 1]; 5351 5352 /* If there is already an error, don't continue. */ 5353 if (asc_dvc->err_code != 0) { 5354 return ADV_ERROR; 5355 } 5356 5357 /* 5358 * The caller must set 'chip_type' to ADV_CHIP_ASC38C1600. 5359 */ 5360 if (asc_dvc->chip_type != ADV_CHIP_ASC38C1600) { 5361 asc_dvc->err_code = ASC_IERR_BAD_CHIPTYPE; 5362 return ADV_ERROR; 5363 } 5364 5365 warn_code = 0; 5366 iop_base = asc_dvc->iop_base; 5367 5368 /* 5369 * Save the RISC memory BIOS region before writing the microcode. 5370 * The BIOS may already be loaded and using its RISC LRAM region 5371 * so its region must be saved and restored. 5372 * 5373 * Note: This code makes the assumption, which is currently true, 5374 * that a chip reset does not clear RISC LRAM. 5375 */ 5376 for (i = 0; i < ASC_MC_BIOSLEN / 2; i++) { 5377 AdvReadWordLram(iop_base, ASC_MC_BIOSMEM + (2 * i), 5378 bios_mem[i]); 5379 } 5380 5381 /* 5382 * Save current per TID negotiated values. 5383 */ 5384 AdvReadWordLram(iop_base, ASC_MC_WDTR_ABLE, wdtr_able); 5385 AdvReadWordLram(iop_base, ASC_MC_SDTR_ABLE, sdtr_able); 5386 AdvReadWordLram(iop_base, ASC_MC_PPR_ABLE, ppr_able); 5387 AdvReadWordLram(iop_base, ASC_MC_TAGQNG_ABLE, tagqng_able); 5388 for (tid = 0; tid <= ASC_MAX_TID; tid++) { 5389 AdvReadByteLram(iop_base, ASC_MC_NUMBER_OF_MAX_CMD + tid, 5390 max_cmd[tid]); 5391 } 5392 5393 /* 5394 * RAM BIST (Built-In Self Test) 5395 * 5396 * Address : I/O base + offset 0x38h register (byte). 5397 * Function: Bit 7-6(RW) : RAM mode 5398 * Normal Mode : 0x00 5399 * Pre-test Mode : 0x40 5400 * RAM Test Mode : 0x80 5401 * Bit 5 : unused 5402 * Bit 4(RO) : Done bit 5403 * Bit 3-0(RO) : Status 5404 * Host Error : 0x08 5405 * Int_RAM Error : 0x04 5406 * RISC Error : 0x02 5407 * SCSI Error : 0x01 5408 * No Error : 0x00 5409 * 5410 * Note: RAM BIST code should be put right here, before loading the 5411 * microcode and after saving the RISC memory BIOS region. 5412 */ 5413 5414 /* 5415 * LRAM Pre-test 5416 * 5417 * Write PRE_TEST_MODE (0x40) to register and wait for 10 milliseconds. 5418 * If Done bit not set or low nibble not PRE_TEST_VALUE (0x05), return 5419 * an error. Reset to NORMAL_MODE (0x00) and do again. If cannot reset 5420 * to NORMAL_MODE, return an error too. 5421 */ 5422 for (i = 0; i < 2; i++) { 5423 AdvWriteByteRegister(iop_base, IOPB_RAM_BIST, PRE_TEST_MODE); 5424 mdelay(10); /* Wait for 10ms before reading back. */ 5425 byte = AdvReadByteRegister(iop_base, IOPB_RAM_BIST); 5426 if ((byte & RAM_TEST_DONE) == 0 5427 || (byte & 0x0F) != PRE_TEST_VALUE) { 5428 asc_dvc->err_code = ASC_IERR_BIST_PRE_TEST; 5429 return ADV_ERROR; 5430 } 5431 5432 AdvWriteByteRegister(iop_base, IOPB_RAM_BIST, NORMAL_MODE); 5433 mdelay(10); /* Wait for 10ms before reading back. */ 5434 if (AdvReadByteRegister(iop_base, IOPB_RAM_BIST) 5435 != NORMAL_VALUE) { 5436 asc_dvc->err_code = ASC_IERR_BIST_PRE_TEST; 5437 return ADV_ERROR; 5438 } 5439 } 5440 5441 /* 5442 * LRAM Test - It takes about 1.5 ms to run through the test. 5443 * 5444 * Write RAM_TEST_MODE (0x80) to register and wait for 10 milliseconds. 5445 * If Done bit not set or Status not 0, save register byte, set the 5446 * err_code, and return an error. 5447 */ 5448 AdvWriteByteRegister(iop_base, IOPB_RAM_BIST, RAM_TEST_MODE); 5449 mdelay(10); /* Wait for 10ms before checking status. */ 5450 5451 byte = AdvReadByteRegister(iop_base, IOPB_RAM_BIST); 5452 if ((byte & RAM_TEST_DONE) == 0 || (byte & RAM_TEST_STATUS) != 0) { 5453 /* Get here if Done bit not set or Status not 0. */ 5454 asc_dvc->bist_err_code = byte; /* for BIOS display message */ 5455 asc_dvc->err_code = ASC_IERR_BIST_RAM_TEST; 5456 return ADV_ERROR; 5457 } 5458 5459 /* We need to reset back to normal mode after LRAM test passes. */ 5460 AdvWriteByteRegister(iop_base, IOPB_RAM_BIST, NORMAL_MODE); 5461 5462 err = request_firmware(&fw, fwname, asc_dvc->drv_ptr->dev); 5463 if (err) { 5464 printk(KERN_ERR "Failed to load image \"%s\" err %d\n", 5465 fwname, err); 5466 asc_dvc->err_code = ASC_IERR_MCODE_CHKSUM; 5467 return err; 5468 } 5469 if (fw->size < 4) { 5470 printk(KERN_ERR "Bogus length %zu in image \"%s\"\n", 5471 fw->size, fwname); 5472 release_firmware(fw); 5473 asc_dvc->err_code = ASC_IERR_MCODE_CHKSUM; 5474 return -EINVAL; 5475 } 5476 chksum = (fw->data[3] << 24) | (fw->data[2] << 16) | 5477 (fw->data[1] << 8) | fw->data[0]; 5478 asc_dvc->err_code = AdvLoadMicrocode(iop_base, &fw->data[4], 5479 fw->size - 4, ADV_38C1600_MEMSIZE, 5480 chksum); 5481 release_firmware(fw); 5482 if (asc_dvc->err_code) 5483 return ADV_ERROR; 5484 5485 /* 5486 * Restore the RISC memory BIOS region. 5487 */ 5488 for (i = 0; i < ASC_MC_BIOSLEN / 2; i++) { 5489 AdvWriteWordLram(iop_base, ASC_MC_BIOSMEM + (2 * i), 5490 bios_mem[i]); 5491 } 5492 5493 /* 5494 * Calculate and write the microcode code checksum to the microcode 5495 * code checksum location ASC_MC_CODE_CHK_SUM (0x2C). 5496 */ 5497 AdvReadWordLram(iop_base, ASC_MC_CODE_BEGIN_ADDR, begin_addr); 5498 AdvReadWordLram(iop_base, ASC_MC_CODE_END_ADDR, end_addr); 5499 code_sum = 0; 5500 AdvWriteWordRegister(iop_base, IOPW_RAM_ADDR, begin_addr); 5501 for (word = begin_addr; word < end_addr; word += 2) { 5502 code_sum += AdvReadWordAutoIncLram(iop_base); 5503 } 5504 AdvWriteWordLram(iop_base, ASC_MC_CODE_CHK_SUM, code_sum); 5505 5506 /* 5507 * Read microcode version and date. 5508 */ 5509 AdvReadWordLram(iop_base, ASC_MC_VERSION_DATE, 5510 asc_dvc->cfg->mcode_date); 5511 AdvReadWordLram(iop_base, ASC_MC_VERSION_NUM, 5512 asc_dvc->cfg->mcode_version); 5513 5514 /* 5515 * Set the chip type to indicate the ASC38C1600. 5516 */ 5517 AdvWriteWordLram(iop_base, ASC_MC_CHIP_TYPE, ADV_CHIP_ASC38C1600); 5518 5519 /* 5520 * Write 1 to bit 14 'DIS_TERM_DRV' in the SCSI_CFG1 register. 5521 * When DIS_TERM_DRV set to 1, C_DET[3:0] will reflect current 5522 * cable detection and then we are able to read C_DET[3:0]. 5523 * 5524 * Note: We will reset DIS_TERM_DRV to 0 in the 'Set SCSI_CFG1 5525 * Microcode Default Value' section below. 5526 */ 5527 scsi_cfg1 = AdvReadWordRegister(iop_base, IOPW_SCSI_CFG1); 5528 AdvWriteWordRegister(iop_base, IOPW_SCSI_CFG1, 5529 scsi_cfg1 | DIS_TERM_DRV); 5530 5531 /* 5532 * If the PCI Configuration Command Register "Parity Error Response 5533 * Control" Bit was clear (0), then set the microcode variable 5534 * 'control_flag' CONTROL_FLAG_IGNORE_PERR flag to tell the microcode 5535 * to ignore DMA parity errors. 5536 */ 5537 if (asc_dvc->cfg->control_flag & CONTROL_FLAG_IGNORE_PERR) { 5538 AdvReadWordLram(iop_base, ASC_MC_CONTROL_FLAG, word); 5539 word |= CONTROL_FLAG_IGNORE_PERR; 5540 AdvWriteWordLram(iop_base, ASC_MC_CONTROL_FLAG, word); 5541 } 5542 5543 /* 5544 * If the BIOS control flag AIPP (Asynchronous Information 5545 * Phase Protection) disable bit is not set, then set the firmware 5546 * 'control_flag' CONTROL_FLAG_ENABLE_AIPP bit to enable 5547 * AIPP checking and encoding. 5548 */ 5549 if ((asc_dvc->bios_ctrl & BIOS_CTRL_AIPP_DIS) == 0) { 5550 AdvReadWordLram(iop_base, ASC_MC_CONTROL_FLAG, word); 5551 word |= CONTROL_FLAG_ENABLE_AIPP; 5552 AdvWriteWordLram(iop_base, ASC_MC_CONTROL_FLAG, word); 5553 } 5554 5555 /* 5556 * For ASC-38C1600 use DMA_CFG0 default values: FIFO_THRESH_80B [6:4], 5557 * and START_CTL_TH [3:2]. 5558 */ 5559 AdvWriteByteRegister(iop_base, IOPB_DMA_CFG0, 5560 FIFO_THRESH_80B | START_CTL_TH | READ_CMD_MRM); 5561 5562 /* 5563 * Microcode operating variables for WDTR, SDTR, and command tag 5564 * queuing will be set in slave_configure() based on what a 5565 * device reports it is capable of in Inquiry byte 7. 5566 * 5567 * If SCSI Bus Resets have been disabled, then directly set 5568 * SDTR and WDTR from the EEPROM configuration. This will allow 5569 * the BIOS and warm boot to work without a SCSI bus hang on 5570 * the Inquiry caused by host and target mismatched DTR values. 5571 * Without the SCSI Bus Reset, before an Inquiry a device can't 5572 * be assumed to be in Asynchronous, Narrow mode. 5573 */ 5574 if ((asc_dvc->bios_ctrl & BIOS_CTRL_RESET_SCSI_BUS) == 0) { 5575 AdvWriteWordLram(iop_base, ASC_MC_WDTR_ABLE, 5576 asc_dvc->wdtr_able); 5577 AdvWriteWordLram(iop_base, ASC_MC_SDTR_ABLE, 5578 asc_dvc->sdtr_able); 5579 } 5580 5581 /* 5582 * Set microcode operating variables for DISC and SDTR_SPEED1, 5583 * SDTR_SPEED2, SDTR_SPEED3, and SDTR_SPEED4 based on the EEPROM 5584 * configuration values. 5585 * 5586 * The SDTR per TID bitmask overrides the SDTR_SPEED1, SDTR_SPEED2, 5587 * SDTR_SPEED3, and SDTR_SPEED4 values so it is safe to set them 5588 * without determining here whether the device supports SDTR. 5589 */ 5590 AdvWriteWordLram(iop_base, ASC_MC_DISC_ENABLE, 5591 asc_dvc->cfg->disc_enable); 5592 AdvWriteWordLram(iop_base, ASC_MC_SDTR_SPEED1, asc_dvc->sdtr_speed1); 5593 AdvWriteWordLram(iop_base, ASC_MC_SDTR_SPEED2, asc_dvc->sdtr_speed2); 5594 AdvWriteWordLram(iop_base, ASC_MC_SDTR_SPEED3, asc_dvc->sdtr_speed3); 5595 AdvWriteWordLram(iop_base, ASC_MC_SDTR_SPEED4, asc_dvc->sdtr_speed4); 5596 5597 /* 5598 * Set SCSI_CFG0 Microcode Default Value. 5599 * 5600 * The microcode will set the SCSI_CFG0 register using this value 5601 * after it is started below. 5602 */ 5603 AdvWriteWordLram(iop_base, ASC_MC_DEFAULT_SCSI_CFG0, 5604 PARITY_EN | QUEUE_128 | SEL_TMO_LONG | OUR_ID_EN | 5605 asc_dvc->chip_scsi_id); 5606 5607 /* 5608 * Calculate SCSI_CFG1 Microcode Default Value. 5609 * 5610 * The microcode will set the SCSI_CFG1 register using this value 5611 * after it is started below. 5612 * 5613 * Each ASC-38C1600 function has only two cable detect bits. 5614 * The bus mode override bits are in IOPB_SOFT_OVER_WR. 5615 */ 5616 scsi_cfg1 = AdvReadWordRegister(iop_base, IOPW_SCSI_CFG1); 5617 5618 /* 5619 * If the cable is reversed all of the SCSI_CTRL register signals 5620 * will be set. Check for and return an error if this condition is 5621 * found. 5622 */ 5623 if ((AdvReadWordRegister(iop_base, IOPW_SCSI_CTRL) & 0x3F07) == 0x3F07) { 5624 asc_dvc->err_code |= ASC_IERR_REVERSED_CABLE; 5625 return ADV_ERROR; 5626 } 5627 5628 /* 5629 * Each ASC-38C1600 function has two connectors. Only an HVD device 5630 * can not be connected to either connector. An LVD device or SE device 5631 * may be connected to either connecor. If an SE device is connected, 5632 * then at most Ultra speed (20 Mhz) can be used on both connectors. 5633 * 5634 * If an HVD device is attached, return an error. 5635 */ 5636 if (scsi_cfg1 & HVD) { 5637 asc_dvc->err_code |= ASC_IERR_HVD_DEVICE; 5638 return ADV_ERROR; 5639 } 5640 5641 /* 5642 * Each function in the ASC-38C1600 uses only the SE cable detect and 5643 * termination because there are two connectors for each function. Each 5644 * function may use either LVD or SE mode. Corresponding the SE automatic 5645 * termination control EEPROM bits are used for each function. Each 5646 * function has its own EEPROM. If SE automatic control is enabled for 5647 * the function, then set the termination value based on a table listed 5648 * in a_condor.h. 5649 * 5650 * If manual termination is specified in the EEPROM for the function, 5651 * then 'termination' was set-up in AscInitFrom38C1600EEPROM() and is 5652 * ready to be 'ored' into SCSI_CFG1. 5653 */ 5654 if ((asc_dvc->cfg->termination & TERM_SE) == 0) { 5655 struct pci_dev *pdev = adv_dvc_to_pdev(asc_dvc); 5656 /* SE automatic termination control is enabled. */ 5657 switch (scsi_cfg1 & C_DET_SE) { 5658 /* TERM_SE_HI: on, TERM_SE_LO: on */ 5659 case 0x1: 5660 case 0x2: 5661 case 0x3: 5662 asc_dvc->cfg->termination |= TERM_SE; 5663 break; 5664 5665 case 0x0: 5666 if (PCI_FUNC(pdev->devfn) == 0) { 5667 /* Function 0 - TERM_SE_HI: off, TERM_SE_LO: off */ 5668 } else { 5669 /* Function 1 - TERM_SE_HI: on, TERM_SE_LO: off */ 5670 asc_dvc->cfg->termination |= TERM_SE_HI; 5671 } 5672 break; 5673 } 5674 } 5675 5676 /* 5677 * Clear any set TERM_SE bits. 5678 */ 5679 scsi_cfg1 &= ~TERM_SE; 5680 5681 /* 5682 * Invert the TERM_SE bits and then set 'scsi_cfg1'. 5683 */ 5684 scsi_cfg1 |= (~asc_dvc->cfg->termination & TERM_SE); 5685 5686 /* 5687 * Clear Big Endian and Terminator Polarity bits and set possibly 5688 * modified termination control bits in the Microcode SCSI_CFG1 5689 * Register Value. 5690 * 5691 * Big Endian bit is not used even on big endian machines. 5692 */ 5693 scsi_cfg1 &= (~BIG_ENDIAN & ~DIS_TERM_DRV & ~TERM_POL); 5694 5695 /* 5696 * Set SCSI_CFG1 Microcode Default Value 5697 * 5698 * Set possibly modified termination control bits in the Microcode 5699 * SCSI_CFG1 Register Value. 5700 * 5701 * The microcode will set the SCSI_CFG1 register using this value 5702 * after it is started below. 5703 */ 5704 AdvWriteWordLram(iop_base, ASC_MC_DEFAULT_SCSI_CFG1, scsi_cfg1); 5705 5706 /* 5707 * Set MEM_CFG Microcode Default Value 5708 * 5709 * The microcode will set the MEM_CFG register using this value 5710 * after it is started below. 5711 * 5712 * MEM_CFG may be accessed as a word or byte, but only bits 0-7 5713 * are defined. 5714 * 5715 * ASC-38C1600 has 32KB internal memory. 5716 * 5717 * XXX - Since ASC38C1600 Rev.3 has a Local RAM failure issue, we come 5718 * out a special 16K Adv Library and Microcode version. After the issue 5719 * resolved, we should turn back to the 32K support. Both a_condor.h and 5720 * mcode.sas files also need to be updated. 5721 * 5722 * AdvWriteWordLram(iop_base, ASC_MC_DEFAULT_MEM_CFG, 5723 * BIOS_EN | RAM_SZ_32KB); 5724 */ 5725 AdvWriteWordLram(iop_base, ASC_MC_DEFAULT_MEM_CFG, 5726 BIOS_EN | RAM_SZ_16KB); 5727 5728 /* 5729 * Set SEL_MASK Microcode Default Value 5730 * 5731 * The microcode will set the SEL_MASK register using this value 5732 * after it is started below. 5733 */ 5734 AdvWriteWordLram(iop_base, ASC_MC_DEFAULT_SEL_MASK, 5735 ADV_TID_TO_TIDMASK(asc_dvc->chip_scsi_id)); 5736 5737 AdvBuildCarrierFreelist(asc_dvc); 5738 5739 /* 5740 * Set-up the Host->RISC Initiator Command Queue (ICQ). 5741 */ 5742 asc_dvc->icq_sp = adv_get_next_carrier(asc_dvc); 5743 if (!asc_dvc->icq_sp) { 5744 asc_dvc->err_code |= ASC_IERR_NO_CARRIER; 5745 return ADV_ERROR; 5746 } 5747 5748 /* 5749 * Set RISC ICQ physical address start value. Initialize the 5750 * COMMA register to the same value otherwise the RISC will 5751 * prematurely detect a command is available. 5752 */ 5753 AdvWriteDWordLramNoSwap(iop_base, ASC_MC_ICQ, asc_dvc->icq_sp->carr_pa); 5754 AdvWriteDWordRegister(iop_base, IOPDW_COMMA, 5755 le32_to_cpu(asc_dvc->icq_sp->carr_pa)); 5756 5757 /* 5758 * Set-up the RISC->Host Initiator Response Queue (IRQ). 5759 */ 5760 asc_dvc->irq_sp = adv_get_next_carrier(asc_dvc); 5761 if (!asc_dvc->irq_sp) { 5762 asc_dvc->err_code |= ASC_IERR_NO_CARRIER; 5763 return ADV_ERROR; 5764 } 5765 5766 /* 5767 * Set RISC IRQ physical address start value. 5768 */ 5769 AdvWriteDWordLramNoSwap(iop_base, ASC_MC_IRQ, asc_dvc->irq_sp->carr_pa); 5770 asc_dvc->carr_pending_cnt = 0; 5771 5772 AdvWriteByteRegister(iop_base, IOPB_INTR_ENABLES, 5773 (ADV_INTR_ENABLE_HOST_INTR | 5774 ADV_INTR_ENABLE_GLOBAL_INTR)); 5775 AdvReadWordLram(iop_base, ASC_MC_CODE_BEGIN_ADDR, word); 5776 AdvWriteWordRegister(iop_base, IOPW_PC, word); 5777 5778 /* finally, finally, gentlemen, start your engine */ 5779 AdvWriteWordRegister(iop_base, IOPW_RISC_CSR, ADV_RISC_CSR_RUN); 5780 5781 /* 5782 * Reset the SCSI Bus if the EEPROM indicates that SCSI Bus 5783 * Resets should be performed. The RISC has to be running 5784 * to issue a SCSI Bus Reset. 5785 */ 5786 if (asc_dvc->bios_ctrl & BIOS_CTRL_RESET_SCSI_BUS) { 5787 /* 5788 * If the BIOS Signature is present in memory, restore the 5789 * per TID microcode operating variables. 5790 */ 5791 if (bios_mem[(ASC_MC_BIOS_SIGNATURE - ASC_MC_BIOSMEM) / 2] == 5792 0x55AA) { 5793 /* 5794 * Restore per TID negotiated values. 5795 */ 5796 AdvWriteWordLram(iop_base, ASC_MC_WDTR_ABLE, wdtr_able); 5797 AdvWriteWordLram(iop_base, ASC_MC_SDTR_ABLE, sdtr_able); 5798 AdvWriteWordLram(iop_base, ASC_MC_PPR_ABLE, ppr_able); 5799 AdvWriteWordLram(iop_base, ASC_MC_TAGQNG_ABLE, 5800 tagqng_able); 5801 for (tid = 0; tid <= ASC_MAX_TID; tid++) { 5802 AdvWriteByteLram(iop_base, 5803 ASC_MC_NUMBER_OF_MAX_CMD + tid, 5804 max_cmd[tid]); 5805 } 5806 } else { 5807 if (AdvResetSB(asc_dvc) != ADV_TRUE) { 5808 warn_code = ASC_WARN_BUSRESET_ERROR; 5809 } 5810 } 5811 } 5812 5813 return warn_code; 5814 } 5815 5816 /* 5817 * Reset chip and SCSI Bus. 5818 * 5819 * Return Value: 5820 * ADV_TRUE(1) - Chip re-initialization and SCSI Bus Reset successful. 5821 * ADV_FALSE(0) - Chip re-initialization and SCSI Bus Reset failure. 5822 */ 5823 static int AdvResetChipAndSB(ADV_DVC_VAR *asc_dvc) 5824 { 5825 int status; 5826 ushort wdtr_able, sdtr_able, tagqng_able; 5827 ushort ppr_able = 0; 5828 uchar tid, max_cmd[ADV_MAX_TID + 1]; 5829 AdvPortAddr iop_base; 5830 ushort bios_sig; 5831 5832 iop_base = asc_dvc->iop_base; 5833 5834 /* 5835 * Save current per TID negotiated values. 5836 */ 5837 AdvReadWordLram(iop_base, ASC_MC_WDTR_ABLE, wdtr_able); 5838 AdvReadWordLram(iop_base, ASC_MC_SDTR_ABLE, sdtr_able); 5839 if (asc_dvc->chip_type == ADV_CHIP_ASC38C1600) { 5840 AdvReadWordLram(iop_base, ASC_MC_PPR_ABLE, ppr_able); 5841 } 5842 AdvReadWordLram(iop_base, ASC_MC_TAGQNG_ABLE, tagqng_able); 5843 for (tid = 0; tid <= ADV_MAX_TID; tid++) { 5844 AdvReadByteLram(iop_base, ASC_MC_NUMBER_OF_MAX_CMD + tid, 5845 max_cmd[tid]); 5846 } 5847 5848 /* 5849 * Force the AdvInitAsc3550/38C0800Driver() function to 5850 * perform a SCSI Bus Reset by clearing the BIOS signature word. 5851 * The initialization functions assumes a SCSI Bus Reset is not 5852 * needed if the BIOS signature word is present. 5853 */ 5854 AdvReadWordLram(iop_base, ASC_MC_BIOS_SIGNATURE, bios_sig); 5855 AdvWriteWordLram(iop_base, ASC_MC_BIOS_SIGNATURE, 0); 5856 5857 /* 5858 * Stop chip and reset it. 5859 */ 5860 AdvWriteWordRegister(iop_base, IOPW_RISC_CSR, ADV_RISC_CSR_STOP); 5861 AdvWriteWordRegister(iop_base, IOPW_CTRL_REG, ADV_CTRL_REG_CMD_RESET); 5862 mdelay(100); 5863 AdvWriteWordRegister(iop_base, IOPW_CTRL_REG, 5864 ADV_CTRL_REG_CMD_WR_IO_REG); 5865 5866 /* 5867 * Reset Adv Library error code, if any, and try 5868 * re-initializing the chip. 5869 */ 5870 asc_dvc->err_code = 0; 5871 if (asc_dvc->chip_type == ADV_CHIP_ASC38C1600) { 5872 status = AdvInitAsc38C1600Driver(asc_dvc); 5873 } else if (asc_dvc->chip_type == ADV_CHIP_ASC38C0800) { 5874 status = AdvInitAsc38C0800Driver(asc_dvc); 5875 } else { 5876 status = AdvInitAsc3550Driver(asc_dvc); 5877 } 5878 5879 /* Translate initialization return value to status value. */ 5880 if (status == 0) { 5881 status = ADV_TRUE; 5882 } else { 5883 status = ADV_FALSE; 5884 } 5885 5886 /* 5887 * Restore the BIOS signature word. 5888 */ 5889 AdvWriteWordLram(iop_base, ASC_MC_BIOS_SIGNATURE, bios_sig); 5890 5891 /* 5892 * Restore per TID negotiated values. 5893 */ 5894 AdvWriteWordLram(iop_base, ASC_MC_WDTR_ABLE, wdtr_able); 5895 AdvWriteWordLram(iop_base, ASC_MC_SDTR_ABLE, sdtr_able); 5896 if (asc_dvc->chip_type == ADV_CHIP_ASC38C1600) { 5897 AdvWriteWordLram(iop_base, ASC_MC_PPR_ABLE, ppr_able); 5898 } 5899 AdvWriteWordLram(iop_base, ASC_MC_TAGQNG_ABLE, tagqng_able); 5900 for (tid = 0; tid <= ADV_MAX_TID; tid++) { 5901 AdvWriteByteLram(iop_base, ASC_MC_NUMBER_OF_MAX_CMD + tid, 5902 max_cmd[tid]); 5903 } 5904 5905 return status; 5906 } 5907 5908 /* 5909 * adv_async_callback() - Adv Library asynchronous event callback function. 5910 */ 5911 static void adv_async_callback(ADV_DVC_VAR *adv_dvc_varp, uchar code) 5912 { 5913 switch (code) { 5914 case ADV_ASYNC_SCSI_BUS_RESET_DET: 5915 /* 5916 * The firmware detected a SCSI Bus reset. 5917 */ 5918 ASC_DBG(0, "ADV_ASYNC_SCSI_BUS_RESET_DET\n"); 5919 break; 5920 5921 case ADV_ASYNC_RDMA_FAILURE: 5922 /* 5923 * Handle RDMA failure by resetting the SCSI Bus and 5924 * possibly the chip if it is unresponsive. Log the error 5925 * with a unique code. 5926 */ 5927 ASC_DBG(0, "ADV_ASYNC_RDMA_FAILURE\n"); 5928 AdvResetChipAndSB(adv_dvc_varp); 5929 break; 5930 5931 case ADV_HOST_SCSI_BUS_RESET: 5932 /* 5933 * Host generated SCSI bus reset occurred. 5934 */ 5935 ASC_DBG(0, "ADV_HOST_SCSI_BUS_RESET\n"); 5936 break; 5937 5938 default: 5939 ASC_DBG(0, "unknown code 0x%x\n", code); 5940 break; 5941 } 5942 } 5943 5944 /* 5945 * adv_isr_callback() - Second Level Interrupt Handler called by AdvISR(). 5946 * 5947 * Callback function for the Wide SCSI Adv Library. 5948 */ 5949 static void adv_isr_callback(ADV_DVC_VAR *adv_dvc_varp, ADV_SCSI_REQ_Q *scsiqp) 5950 { 5951 struct asc_board *boardp = adv_dvc_varp->drv_ptr; 5952 adv_req_t *reqp; 5953 adv_sgblk_t *sgblkp; 5954 struct scsi_cmnd *scp; 5955 u32 resid_cnt; 5956 dma_addr_t sense_addr; 5957 5958 ASC_DBG(1, "adv_dvc_varp 0x%p, scsiqp 0x%p\n", 5959 adv_dvc_varp, scsiqp); 5960 ASC_DBG_PRT_ADV_SCSI_REQ_Q(2, scsiqp); 5961 5962 /* 5963 * Get the adv_req_t structure for the command that has been 5964 * completed. The adv_req_t structure actually contains the 5965 * completed ADV_SCSI_REQ_Q structure. 5966 */ 5967 scp = scsi_host_find_tag(boardp->shost, scsiqp->srb_tag); 5968 5969 ASC_DBG(1, "scp 0x%p\n", scp); 5970 if (scp == NULL) { 5971 ASC_PRINT 5972 ("adv_isr_callback: scp is NULL; adv_req_t dropped.\n"); 5973 return; 5974 } 5975 ASC_DBG_PRT_CDB(2, scp->cmnd, scp->cmd_len); 5976 5977 reqp = (adv_req_t *)scp->host_scribble; 5978 ASC_DBG(1, "reqp 0x%lx\n", (ulong)reqp); 5979 if (reqp == NULL) { 5980 ASC_PRINT("adv_isr_callback: reqp is NULL\n"); 5981 return; 5982 } 5983 /* 5984 * Remove backreferences to avoid duplicate 5985 * command completions. 5986 */ 5987 scp->host_scribble = NULL; 5988 reqp->cmndp = NULL; 5989 5990 ASC_STATS(boardp->shost, callback); 5991 ASC_DBG(1, "shost 0x%p\n", boardp->shost); 5992 5993 sense_addr = le32_to_cpu(scsiqp->sense_addr); 5994 dma_unmap_single(boardp->dev, sense_addr, 5995 SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE); 5996 5997 /* 5998 * 'done_status' contains the command's ending status. 5999 */ 6000 switch (scsiqp->done_status) { 6001 case QD_NO_ERROR: 6002 ASC_DBG(2, "QD_NO_ERROR\n"); 6003 scp->result = 0; 6004 6005 /* 6006 * Check for an underrun condition. 6007 * 6008 * If there was no error and an underrun condition, then 6009 * then return the number of underrun bytes. 6010 */ 6011 resid_cnt = le32_to_cpu(scsiqp->data_cnt); 6012 if (scsi_bufflen(scp) != 0 && resid_cnt != 0 && 6013 resid_cnt <= scsi_bufflen(scp)) { 6014 ASC_DBG(1, "underrun condition %lu bytes\n", 6015 (ulong)resid_cnt); 6016 scsi_set_resid(scp, resid_cnt); 6017 } 6018 break; 6019 6020 case QD_WITH_ERROR: 6021 ASC_DBG(2, "QD_WITH_ERROR\n"); 6022 switch (scsiqp->host_status) { 6023 case QHSTA_NO_ERROR: 6024 if (scsiqp->scsi_status == SAM_STAT_CHECK_CONDITION) { 6025 ASC_DBG(2, "SAM_STAT_CHECK_CONDITION\n"); 6026 ASC_DBG_PRT_SENSE(2, scp->sense_buffer, 6027 SCSI_SENSE_BUFFERSIZE); 6028 /* 6029 * Note: The 'status_byte()' macro used by 6030 * target drivers defined in scsi.h shifts the 6031 * status byte returned by host drivers right 6032 * by 1 bit. This is why target drivers also 6033 * use right shifted status byte definitions. 6034 * For instance target drivers use 6035 * CHECK_CONDITION, defined to 0x1, instead of 6036 * the SCSI defined check condition value of 6037 * 0x2. Host drivers are supposed to return 6038 * the status byte as it is defined by SCSI. 6039 */ 6040 scp->result = DRIVER_BYTE(DRIVER_SENSE) | 6041 STATUS_BYTE(scsiqp->scsi_status); 6042 } else { 6043 scp->result = STATUS_BYTE(scsiqp->scsi_status); 6044 } 6045 break; 6046 6047 default: 6048 /* Some other QHSTA error occurred. */ 6049 ASC_DBG(1, "host_status 0x%x\n", scsiqp->host_status); 6050 scp->result = HOST_BYTE(DID_BAD_TARGET); 6051 break; 6052 } 6053 break; 6054 6055 case QD_ABORTED_BY_HOST: 6056 ASC_DBG(1, "QD_ABORTED_BY_HOST\n"); 6057 scp->result = 6058 HOST_BYTE(DID_ABORT) | STATUS_BYTE(scsiqp->scsi_status); 6059 break; 6060 6061 default: 6062 ASC_DBG(1, "done_status 0x%x\n", scsiqp->done_status); 6063 scp->result = 6064 HOST_BYTE(DID_ERROR) | STATUS_BYTE(scsiqp->scsi_status); 6065 break; 6066 } 6067 6068 /* 6069 * If the 'init_tidmask' bit isn't already set for the target and the 6070 * current request finished normally, then set the bit for the target 6071 * to indicate that a device is present. 6072 */ 6073 if ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(scp->device->id)) == 0 && 6074 scsiqp->done_status == QD_NO_ERROR && 6075 scsiqp->host_status == QHSTA_NO_ERROR) { 6076 boardp->init_tidmask |= ADV_TID_TO_TIDMASK(scp->device->id); 6077 } 6078 6079 asc_scsi_done(scp); 6080 6081 /* 6082 * Free all 'adv_sgblk_t' structures allocated for the request. 6083 */ 6084 while ((sgblkp = reqp->sgblkp) != NULL) { 6085 /* Remove 'sgblkp' from the request list. */ 6086 reqp->sgblkp = sgblkp->next_sgblkp; 6087 6088 dma_pool_free(boardp->adv_sgblk_pool, sgblkp, 6089 sgblkp->sg_addr); 6090 } 6091 6092 ASC_DBG(1, "done\n"); 6093 } 6094 6095 /* 6096 * Adv Library Interrupt Service Routine 6097 * 6098 * This function is called by a driver's interrupt service routine. 6099 * The function disables and re-enables interrupts. 6100 * 6101 * When a microcode idle command is completed, the ADV_DVC_VAR 6102 * 'idle_cmd_done' field is set to ADV_TRUE. 6103 * 6104 * Note: AdvISR() can be called when interrupts are disabled or even 6105 * when there is no hardware interrupt condition present. It will 6106 * always check for completed idle commands and microcode requests. 6107 * This is an important feature that shouldn't be changed because it 6108 * allows commands to be completed from polling mode loops. 6109 * 6110 * Return: 6111 * ADV_TRUE(1) - interrupt was pending 6112 * ADV_FALSE(0) - no interrupt was pending 6113 */ 6114 static int AdvISR(ADV_DVC_VAR *asc_dvc) 6115 { 6116 AdvPortAddr iop_base; 6117 uchar int_stat; 6118 ushort target_bit; 6119 ADV_CARR_T *free_carrp; 6120 __le32 irq_next_vpa; 6121 ADV_SCSI_REQ_Q *scsiq; 6122 adv_req_t *reqp; 6123 6124 iop_base = asc_dvc->iop_base; 6125 6126 /* Reading the register clears the interrupt. */ 6127 int_stat = AdvReadByteRegister(iop_base, IOPB_INTR_STATUS_REG); 6128 6129 if ((int_stat & (ADV_INTR_STATUS_INTRA | ADV_INTR_STATUS_INTRB | 6130 ADV_INTR_STATUS_INTRC)) == 0) { 6131 return ADV_FALSE; 6132 } 6133 6134 /* 6135 * Notify the driver of an asynchronous microcode condition by 6136 * calling the adv_async_callback function. The function 6137 * is passed the microcode ASC_MC_INTRB_CODE byte value. 6138 */ 6139 if (int_stat & ADV_INTR_STATUS_INTRB) { 6140 uchar intrb_code; 6141 6142 AdvReadByteLram(iop_base, ASC_MC_INTRB_CODE, intrb_code); 6143 6144 if (asc_dvc->chip_type == ADV_CHIP_ASC3550 || 6145 asc_dvc->chip_type == ADV_CHIP_ASC38C0800) { 6146 if (intrb_code == ADV_ASYNC_CARRIER_READY_FAILURE && 6147 asc_dvc->carr_pending_cnt != 0) { 6148 AdvWriteByteRegister(iop_base, IOPB_TICKLE, 6149 ADV_TICKLE_A); 6150 if (asc_dvc->chip_type == ADV_CHIP_ASC3550) { 6151 AdvWriteByteRegister(iop_base, 6152 IOPB_TICKLE, 6153 ADV_TICKLE_NOP); 6154 } 6155 } 6156 } 6157 6158 adv_async_callback(asc_dvc, intrb_code); 6159 } 6160 6161 /* 6162 * Check if the IRQ stopper carrier contains a completed request. 6163 */ 6164 while (((irq_next_vpa = 6165 le32_to_cpu(asc_dvc->irq_sp->next_vpa)) & ADV_RQ_DONE) != 0) { 6166 /* 6167 * Get a pointer to the newly completed ADV_SCSI_REQ_Q structure. 6168 * The RISC will have set 'areq_vpa' to a virtual address. 6169 * 6170 * The firmware will have copied the ADV_SCSI_REQ_Q.scsiq_ptr 6171 * field to the carrier ADV_CARR_T.areq_vpa field. The conversion 6172 * below complements the conversion of ADV_SCSI_REQ_Q.scsiq_ptr' 6173 * in AdvExeScsiQueue(). 6174 */ 6175 u32 pa_offset = le32_to_cpu(asc_dvc->irq_sp->areq_vpa); 6176 ASC_DBG(1, "irq_sp %p areq_vpa %u\n", 6177 asc_dvc->irq_sp, pa_offset); 6178 reqp = adv_get_reqp(asc_dvc, pa_offset); 6179 scsiq = &reqp->scsi_req_q; 6180 6181 /* 6182 * Request finished with good status and the queue was not 6183 * DMAed to host memory by the firmware. Set all status fields 6184 * to indicate good status. 6185 */ 6186 if ((irq_next_vpa & ADV_RQ_GOOD) != 0) { 6187 scsiq->done_status = QD_NO_ERROR; 6188 scsiq->host_status = scsiq->scsi_status = 0; 6189 scsiq->data_cnt = 0L; 6190 } 6191 6192 /* 6193 * Advance the stopper pointer to the next carrier 6194 * ignoring the lower four bits. Free the previous 6195 * stopper carrier. 6196 */ 6197 free_carrp = asc_dvc->irq_sp; 6198 asc_dvc->irq_sp = adv_get_carrier(asc_dvc, 6199 ADV_GET_CARRP(irq_next_vpa)); 6200 6201 free_carrp->next_vpa = asc_dvc->carr_freelist->carr_va; 6202 asc_dvc->carr_freelist = free_carrp; 6203 asc_dvc->carr_pending_cnt--; 6204 6205 target_bit = ADV_TID_TO_TIDMASK(scsiq->target_id); 6206 6207 /* 6208 * Clear request microcode control flag. 6209 */ 6210 scsiq->cntl = 0; 6211 6212 /* 6213 * Notify the driver of the completed request by passing 6214 * the ADV_SCSI_REQ_Q pointer to its callback function. 6215 */ 6216 adv_isr_callback(asc_dvc, scsiq); 6217 /* 6218 * Note: After the driver callback function is called, 'scsiq' 6219 * can no longer be referenced. 6220 * 6221 * Fall through and continue processing other completed 6222 * requests... 6223 */ 6224 } 6225 return ADV_TRUE; 6226 } 6227 6228 static int AscSetLibErrorCode(ASC_DVC_VAR *asc_dvc, ushort err_code) 6229 { 6230 if (asc_dvc->err_code == 0) { 6231 asc_dvc->err_code = err_code; 6232 AscWriteLramWord(asc_dvc->iop_base, ASCV_ASCDVC_ERR_CODE_W, 6233 err_code); 6234 } 6235 return err_code; 6236 } 6237 6238 static void AscAckInterrupt(PortAddr iop_base) 6239 { 6240 uchar host_flag; 6241 uchar risc_flag; 6242 ushort loop; 6243 6244 loop = 0; 6245 do { 6246 risc_flag = AscReadLramByte(iop_base, ASCV_RISC_FLAG_B); 6247 if (loop++ > 0x7FFF) { 6248 break; 6249 } 6250 } while ((risc_flag & ASC_RISC_FLAG_GEN_INT) != 0); 6251 host_flag = 6252 AscReadLramByte(iop_base, 6253 ASCV_HOST_FLAG_B) & (~ASC_HOST_FLAG_ACK_INT); 6254 AscWriteLramByte(iop_base, ASCV_HOST_FLAG_B, 6255 (uchar)(host_flag | ASC_HOST_FLAG_ACK_INT)); 6256 AscSetChipStatus(iop_base, CIW_INT_ACK); 6257 loop = 0; 6258 while (AscGetChipStatus(iop_base) & CSW_INT_PENDING) { 6259 AscSetChipStatus(iop_base, CIW_INT_ACK); 6260 if (loop++ > 3) { 6261 break; 6262 } 6263 } 6264 AscWriteLramByte(iop_base, ASCV_HOST_FLAG_B, host_flag); 6265 } 6266 6267 static uchar AscGetSynPeriodIndex(ASC_DVC_VAR *asc_dvc, uchar syn_time) 6268 { 6269 const uchar *period_table; 6270 int max_index; 6271 int min_index; 6272 int i; 6273 6274 period_table = asc_dvc->sdtr_period_tbl; 6275 max_index = (int)asc_dvc->max_sdtr_index; 6276 min_index = (int)asc_dvc->min_sdtr_index; 6277 if ((syn_time <= period_table[max_index])) { 6278 for (i = min_index; i < (max_index - 1); i++) { 6279 if (syn_time <= period_table[i]) { 6280 return (uchar)i; 6281 } 6282 } 6283 return (uchar)max_index; 6284 } else { 6285 return (uchar)(max_index + 1); 6286 } 6287 } 6288 6289 static uchar 6290 AscMsgOutSDTR(ASC_DVC_VAR *asc_dvc, uchar sdtr_period, uchar sdtr_offset) 6291 { 6292 PortAddr iop_base = asc_dvc->iop_base; 6293 uchar sdtr_period_index = AscGetSynPeriodIndex(asc_dvc, sdtr_period); 6294 EXT_MSG sdtr_buf = { 6295 .msg_type = EXTENDED_MESSAGE, 6296 .msg_len = MS_SDTR_LEN, 6297 .msg_req = EXTENDED_SDTR, 6298 .xfer_period = sdtr_period, 6299 .req_ack_offset = sdtr_offset, 6300 }; 6301 sdtr_offset &= ASC_SYN_MAX_OFFSET; 6302 6303 if (sdtr_period_index <= asc_dvc->max_sdtr_index) { 6304 AscMemWordCopyPtrToLram(iop_base, ASCV_MSGOUT_BEG, 6305 (uchar *)&sdtr_buf, 6306 sizeof(EXT_MSG) >> 1); 6307 return ((sdtr_period_index << 4) | sdtr_offset); 6308 } else { 6309 sdtr_buf.req_ack_offset = 0; 6310 AscMemWordCopyPtrToLram(iop_base, ASCV_MSGOUT_BEG, 6311 (uchar *)&sdtr_buf, 6312 sizeof(EXT_MSG) >> 1); 6313 return 0; 6314 } 6315 } 6316 6317 static uchar 6318 AscCalSDTRData(ASC_DVC_VAR *asc_dvc, uchar sdtr_period, uchar syn_offset) 6319 { 6320 uchar byte; 6321 uchar sdtr_period_ix; 6322 6323 sdtr_period_ix = AscGetSynPeriodIndex(asc_dvc, sdtr_period); 6324 if (sdtr_period_ix > asc_dvc->max_sdtr_index) 6325 return 0xFF; 6326 byte = (sdtr_period_ix << 4) | (syn_offset & ASC_SYN_MAX_OFFSET); 6327 return byte; 6328 } 6329 6330 static bool AscSetChipSynRegAtID(PortAddr iop_base, uchar id, uchar sdtr_data) 6331 { 6332 ASC_SCSI_BIT_ID_TYPE org_id; 6333 int i; 6334 bool sta = true; 6335 6336 AscSetBank(iop_base, 1); 6337 org_id = AscReadChipDvcID(iop_base); 6338 for (i = 0; i <= ASC_MAX_TID; i++) { 6339 if (org_id == (0x01 << i)) 6340 break; 6341 } 6342 org_id = (ASC_SCSI_BIT_ID_TYPE) i; 6343 AscWriteChipDvcID(iop_base, id); 6344 if (AscReadChipDvcID(iop_base) == (0x01 << id)) { 6345 AscSetBank(iop_base, 0); 6346 AscSetChipSyn(iop_base, sdtr_data); 6347 if (AscGetChipSyn(iop_base) != sdtr_data) { 6348 sta = false; 6349 } 6350 } else { 6351 sta = false; 6352 } 6353 AscSetBank(iop_base, 1); 6354 AscWriteChipDvcID(iop_base, org_id); 6355 AscSetBank(iop_base, 0); 6356 return (sta); 6357 } 6358 6359 static void AscSetChipSDTR(PortAddr iop_base, uchar sdtr_data, uchar tid_no) 6360 { 6361 AscSetChipSynRegAtID(iop_base, tid_no, sdtr_data); 6362 AscPutMCodeSDTRDoneAtID(iop_base, tid_no, sdtr_data); 6363 } 6364 6365 static void AscIsrChipHalted(ASC_DVC_VAR *asc_dvc) 6366 { 6367 EXT_MSG ext_msg; 6368 EXT_MSG out_msg; 6369 ushort halt_q_addr; 6370 bool sdtr_accept; 6371 ushort int_halt_code; 6372 ASC_SCSI_BIT_ID_TYPE scsi_busy; 6373 ASC_SCSI_BIT_ID_TYPE target_id; 6374 PortAddr iop_base; 6375 uchar tag_code; 6376 uchar q_status; 6377 uchar halt_qp; 6378 uchar sdtr_data; 6379 uchar target_ix; 6380 uchar q_cntl, tid_no; 6381 uchar cur_dvc_qng; 6382 uchar asyn_sdtr; 6383 uchar scsi_status; 6384 struct asc_board *boardp; 6385 6386 BUG_ON(!asc_dvc->drv_ptr); 6387 boardp = asc_dvc->drv_ptr; 6388 6389 iop_base = asc_dvc->iop_base; 6390 int_halt_code = AscReadLramWord(iop_base, ASCV_HALTCODE_W); 6391 6392 halt_qp = AscReadLramByte(iop_base, ASCV_CURCDB_B); 6393 halt_q_addr = ASC_QNO_TO_QADDR(halt_qp); 6394 target_ix = AscReadLramByte(iop_base, 6395 (ushort)(halt_q_addr + 6396 (ushort)ASC_SCSIQ_B_TARGET_IX)); 6397 q_cntl = AscReadLramByte(iop_base, 6398 (ushort)(halt_q_addr + (ushort)ASC_SCSIQ_B_CNTL)); 6399 tid_no = ASC_TIX_TO_TID(target_ix); 6400 target_id = (uchar)ASC_TID_TO_TARGET_ID(tid_no); 6401 if (asc_dvc->pci_fix_asyn_xfer & target_id) { 6402 asyn_sdtr = ASYN_SDTR_DATA_FIX_PCI_REV_AB; 6403 } else { 6404 asyn_sdtr = 0; 6405 } 6406 if (int_halt_code == ASC_HALT_DISABLE_ASYN_USE_SYN_FIX) { 6407 if (asc_dvc->pci_fix_asyn_xfer & target_id) { 6408 AscSetChipSDTR(iop_base, 0, tid_no); 6409 boardp->sdtr_data[tid_no] = 0; 6410 } 6411 AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0); 6412 return; 6413 } else if (int_halt_code == ASC_HALT_ENABLE_ASYN_USE_SYN_FIX) { 6414 if (asc_dvc->pci_fix_asyn_xfer & target_id) { 6415 AscSetChipSDTR(iop_base, asyn_sdtr, tid_no); 6416 boardp->sdtr_data[tid_no] = asyn_sdtr; 6417 } 6418 AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0); 6419 return; 6420 } else if (int_halt_code == ASC_HALT_EXTMSG_IN) { 6421 AscMemWordCopyPtrFromLram(iop_base, 6422 ASCV_MSGIN_BEG, 6423 (uchar *)&ext_msg, 6424 sizeof(EXT_MSG) >> 1); 6425 6426 if (ext_msg.msg_type == EXTENDED_MESSAGE && 6427 ext_msg.msg_req == EXTENDED_SDTR && 6428 ext_msg.msg_len == MS_SDTR_LEN) { 6429 sdtr_accept = true; 6430 if ((ext_msg.req_ack_offset > ASC_SYN_MAX_OFFSET)) { 6431 6432 sdtr_accept = false; 6433 ext_msg.req_ack_offset = ASC_SYN_MAX_OFFSET; 6434 } 6435 if ((ext_msg.xfer_period < 6436 asc_dvc->sdtr_period_tbl[asc_dvc->min_sdtr_index]) 6437 || (ext_msg.xfer_period > 6438 asc_dvc->sdtr_period_tbl[asc_dvc-> 6439 max_sdtr_index])) { 6440 sdtr_accept = false; 6441 ext_msg.xfer_period = 6442 asc_dvc->sdtr_period_tbl[asc_dvc-> 6443 min_sdtr_index]; 6444 } 6445 if (sdtr_accept) { 6446 sdtr_data = 6447 AscCalSDTRData(asc_dvc, ext_msg.xfer_period, 6448 ext_msg.req_ack_offset); 6449 if (sdtr_data == 0xFF) { 6450 6451 q_cntl |= QC_MSG_OUT; 6452 asc_dvc->init_sdtr &= ~target_id; 6453 asc_dvc->sdtr_done &= ~target_id; 6454 AscSetChipSDTR(iop_base, asyn_sdtr, 6455 tid_no); 6456 boardp->sdtr_data[tid_no] = asyn_sdtr; 6457 } 6458 } 6459 if (ext_msg.req_ack_offset == 0) { 6460 6461 q_cntl &= ~QC_MSG_OUT; 6462 asc_dvc->init_sdtr &= ~target_id; 6463 asc_dvc->sdtr_done &= ~target_id; 6464 AscSetChipSDTR(iop_base, asyn_sdtr, tid_no); 6465 } else { 6466 if (sdtr_accept && (q_cntl & QC_MSG_OUT)) { 6467 q_cntl &= ~QC_MSG_OUT; 6468 asc_dvc->sdtr_done |= target_id; 6469 asc_dvc->init_sdtr |= target_id; 6470 asc_dvc->pci_fix_asyn_xfer &= 6471 ~target_id; 6472 sdtr_data = 6473 AscCalSDTRData(asc_dvc, 6474 ext_msg.xfer_period, 6475 ext_msg. 6476 req_ack_offset); 6477 AscSetChipSDTR(iop_base, sdtr_data, 6478 tid_no); 6479 boardp->sdtr_data[tid_no] = sdtr_data; 6480 } else { 6481 q_cntl |= QC_MSG_OUT; 6482 AscMsgOutSDTR(asc_dvc, 6483 ext_msg.xfer_period, 6484 ext_msg.req_ack_offset); 6485 asc_dvc->pci_fix_asyn_xfer &= 6486 ~target_id; 6487 sdtr_data = 6488 AscCalSDTRData(asc_dvc, 6489 ext_msg.xfer_period, 6490 ext_msg. 6491 req_ack_offset); 6492 AscSetChipSDTR(iop_base, sdtr_data, 6493 tid_no); 6494 boardp->sdtr_data[tid_no] = sdtr_data; 6495 asc_dvc->sdtr_done |= target_id; 6496 asc_dvc->init_sdtr |= target_id; 6497 } 6498 } 6499 6500 AscWriteLramByte(iop_base, 6501 (ushort)(halt_q_addr + 6502 (ushort)ASC_SCSIQ_B_CNTL), 6503 q_cntl); 6504 AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0); 6505 return; 6506 } else if (ext_msg.msg_type == EXTENDED_MESSAGE && 6507 ext_msg.msg_req == EXTENDED_WDTR && 6508 ext_msg.msg_len == MS_WDTR_LEN) { 6509 6510 ext_msg.wdtr_width = 0; 6511 AscMemWordCopyPtrToLram(iop_base, 6512 ASCV_MSGOUT_BEG, 6513 (uchar *)&ext_msg, 6514 sizeof(EXT_MSG) >> 1); 6515 q_cntl |= QC_MSG_OUT; 6516 AscWriteLramByte(iop_base, 6517 (ushort)(halt_q_addr + 6518 (ushort)ASC_SCSIQ_B_CNTL), 6519 q_cntl); 6520 AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0); 6521 return; 6522 } else { 6523 6524 ext_msg.msg_type = MESSAGE_REJECT; 6525 AscMemWordCopyPtrToLram(iop_base, 6526 ASCV_MSGOUT_BEG, 6527 (uchar *)&ext_msg, 6528 sizeof(EXT_MSG) >> 1); 6529 q_cntl |= QC_MSG_OUT; 6530 AscWriteLramByte(iop_base, 6531 (ushort)(halt_q_addr + 6532 (ushort)ASC_SCSIQ_B_CNTL), 6533 q_cntl); 6534 AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0); 6535 return; 6536 } 6537 } else if (int_halt_code == ASC_HALT_CHK_CONDITION) { 6538 6539 q_cntl |= QC_REQ_SENSE; 6540 6541 if ((asc_dvc->init_sdtr & target_id) != 0) { 6542 6543 asc_dvc->sdtr_done &= ~target_id; 6544 6545 sdtr_data = AscGetMCodeInitSDTRAtID(iop_base, tid_no); 6546 q_cntl |= QC_MSG_OUT; 6547 AscMsgOutSDTR(asc_dvc, 6548 asc_dvc-> 6549 sdtr_period_tbl[(sdtr_data >> 4) & 6550 (uchar)(asc_dvc-> 6551 max_sdtr_index - 6552 1)], 6553 (uchar)(sdtr_data & (uchar) 6554 ASC_SYN_MAX_OFFSET)); 6555 } 6556 6557 AscWriteLramByte(iop_base, 6558 (ushort)(halt_q_addr + 6559 (ushort)ASC_SCSIQ_B_CNTL), q_cntl); 6560 6561 tag_code = AscReadLramByte(iop_base, 6562 (ushort)(halt_q_addr + (ushort) 6563 ASC_SCSIQ_B_TAG_CODE)); 6564 tag_code &= 0xDC; 6565 if ((asc_dvc->pci_fix_asyn_xfer & target_id) 6566 && !(asc_dvc->pci_fix_asyn_xfer_always & target_id) 6567 ) { 6568 6569 tag_code |= (ASC_TAG_FLAG_DISABLE_DISCONNECT 6570 | ASC_TAG_FLAG_DISABLE_ASYN_USE_SYN_FIX); 6571 6572 } 6573 AscWriteLramByte(iop_base, 6574 (ushort)(halt_q_addr + 6575 (ushort)ASC_SCSIQ_B_TAG_CODE), 6576 tag_code); 6577 6578 q_status = AscReadLramByte(iop_base, 6579 (ushort)(halt_q_addr + (ushort) 6580 ASC_SCSIQ_B_STATUS)); 6581 q_status |= (QS_READY | QS_BUSY); 6582 AscWriteLramByte(iop_base, 6583 (ushort)(halt_q_addr + 6584 (ushort)ASC_SCSIQ_B_STATUS), 6585 q_status); 6586 6587 scsi_busy = AscReadLramByte(iop_base, (ushort)ASCV_SCSIBUSY_B); 6588 scsi_busy &= ~target_id; 6589 AscWriteLramByte(iop_base, (ushort)ASCV_SCSIBUSY_B, scsi_busy); 6590 6591 AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0); 6592 return; 6593 } else if (int_halt_code == ASC_HALT_SDTR_REJECTED) { 6594 6595 AscMemWordCopyPtrFromLram(iop_base, 6596 ASCV_MSGOUT_BEG, 6597 (uchar *)&out_msg, 6598 sizeof(EXT_MSG) >> 1); 6599 6600 if ((out_msg.msg_type == EXTENDED_MESSAGE) && 6601 (out_msg.msg_len == MS_SDTR_LEN) && 6602 (out_msg.msg_req == EXTENDED_SDTR)) { 6603 6604 asc_dvc->init_sdtr &= ~target_id; 6605 asc_dvc->sdtr_done &= ~target_id; 6606 AscSetChipSDTR(iop_base, asyn_sdtr, tid_no); 6607 boardp->sdtr_data[tid_no] = asyn_sdtr; 6608 } 6609 q_cntl &= ~QC_MSG_OUT; 6610 AscWriteLramByte(iop_base, 6611 (ushort)(halt_q_addr + 6612 (ushort)ASC_SCSIQ_B_CNTL), q_cntl); 6613 AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0); 6614 return; 6615 } else if (int_halt_code == ASC_HALT_SS_QUEUE_FULL) { 6616 6617 scsi_status = AscReadLramByte(iop_base, 6618 (ushort)((ushort)halt_q_addr + 6619 (ushort) 6620 ASC_SCSIQ_SCSI_STATUS)); 6621 cur_dvc_qng = 6622 AscReadLramByte(iop_base, 6623 (ushort)((ushort)ASC_QADR_BEG + 6624 (ushort)target_ix)); 6625 if ((cur_dvc_qng > 0) && (asc_dvc->cur_dvc_qng[tid_no] > 0)) { 6626 6627 scsi_busy = AscReadLramByte(iop_base, 6628 (ushort)ASCV_SCSIBUSY_B); 6629 scsi_busy |= target_id; 6630 AscWriteLramByte(iop_base, 6631 (ushort)ASCV_SCSIBUSY_B, scsi_busy); 6632 asc_dvc->queue_full_or_busy |= target_id; 6633 6634 if (scsi_status == SAM_STAT_TASK_SET_FULL) { 6635 if (cur_dvc_qng > ASC_MIN_TAGGED_CMD) { 6636 cur_dvc_qng -= 1; 6637 asc_dvc->max_dvc_qng[tid_no] = 6638 cur_dvc_qng; 6639 6640 AscWriteLramByte(iop_base, 6641 (ushort)((ushort) 6642 ASCV_MAX_DVC_QNG_BEG 6643 + (ushort) 6644 tid_no), 6645 cur_dvc_qng); 6646 6647 /* 6648 * Set the device queue depth to the 6649 * number of active requests when the 6650 * QUEUE FULL condition was encountered. 6651 */ 6652 boardp->queue_full |= target_id; 6653 boardp->queue_full_cnt[tid_no] = 6654 cur_dvc_qng; 6655 } 6656 } 6657 } 6658 AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0); 6659 return; 6660 } 6661 return; 6662 } 6663 6664 /* 6665 * void 6666 * DvcGetQinfo(PortAddr iop_base, ushort s_addr, uchar *inbuf, int words) 6667 * 6668 * Calling/Exit State: 6669 * none 6670 * 6671 * Description: 6672 * Input an ASC_QDONE_INFO structure from the chip 6673 */ 6674 static void 6675 DvcGetQinfo(PortAddr iop_base, ushort s_addr, uchar *inbuf, int words) 6676 { 6677 int i; 6678 ushort word; 6679 6680 AscSetChipLramAddr(iop_base, s_addr); 6681 for (i = 0; i < 2 * words; i += 2) { 6682 if (i == 10) { 6683 continue; 6684 } 6685 word = inpw(iop_base + IOP_RAM_DATA); 6686 inbuf[i] = word & 0xff; 6687 inbuf[i + 1] = (word >> 8) & 0xff; 6688 } 6689 ASC_DBG_PRT_HEX(2, "DvcGetQinfo", inbuf, 2 * words); 6690 } 6691 6692 static uchar 6693 _AscCopyLramScsiDoneQ(PortAddr iop_base, 6694 ushort q_addr, 6695 ASC_QDONE_INFO *scsiq, unsigned int max_dma_count) 6696 { 6697 ushort _val; 6698 uchar sg_queue_cnt; 6699 6700 DvcGetQinfo(iop_base, 6701 q_addr + ASC_SCSIQ_DONE_INFO_BEG, 6702 (uchar *)scsiq, 6703 (sizeof(ASC_SCSIQ_2) + sizeof(ASC_SCSIQ_3)) / 2); 6704 6705 _val = AscReadLramWord(iop_base, 6706 (ushort)(q_addr + (ushort)ASC_SCSIQ_B_STATUS)); 6707 scsiq->q_status = (uchar)_val; 6708 scsiq->q_no = (uchar)(_val >> 8); 6709 _val = AscReadLramWord(iop_base, 6710 (ushort)(q_addr + (ushort)ASC_SCSIQ_B_CNTL)); 6711 scsiq->cntl = (uchar)_val; 6712 sg_queue_cnt = (uchar)(_val >> 8); 6713 _val = AscReadLramWord(iop_base, 6714 (ushort)(q_addr + 6715 (ushort)ASC_SCSIQ_B_SENSE_LEN)); 6716 scsiq->sense_len = (uchar)_val; 6717 scsiq->extra_bytes = (uchar)(_val >> 8); 6718 6719 /* 6720 * Read high word of remain bytes from alternate location. 6721 */ 6722 scsiq->remain_bytes = (((u32)AscReadLramWord(iop_base, 6723 (ushort)(q_addr + 6724 (ushort) 6725 ASC_SCSIQ_W_ALT_DC1))) 6726 << 16); 6727 /* 6728 * Read low word of remain bytes from original location. 6729 */ 6730 scsiq->remain_bytes += AscReadLramWord(iop_base, 6731 (ushort)(q_addr + (ushort) 6732 ASC_SCSIQ_DW_REMAIN_XFER_CNT)); 6733 6734 scsiq->remain_bytes &= max_dma_count; 6735 return sg_queue_cnt; 6736 } 6737 6738 /* 6739 * asc_isr_callback() - Second Level Interrupt Handler called by AscISR(). 6740 * 6741 * Interrupt callback function for the Narrow SCSI Asc Library. 6742 */ 6743 static void asc_isr_callback(ASC_DVC_VAR *asc_dvc_varp, ASC_QDONE_INFO *qdonep) 6744 { 6745 struct asc_board *boardp = asc_dvc_varp->drv_ptr; 6746 u32 srb_tag; 6747 struct scsi_cmnd *scp; 6748 6749 ASC_DBG(1, "asc_dvc_varp 0x%p, qdonep 0x%p\n", asc_dvc_varp, qdonep); 6750 ASC_DBG_PRT_ASC_QDONE_INFO(2, qdonep); 6751 6752 /* 6753 * Decrease the srb_tag by 1 to find the SCSI command 6754 */ 6755 srb_tag = qdonep->d2.srb_tag - 1; 6756 scp = scsi_host_find_tag(boardp->shost, srb_tag); 6757 if (!scp) 6758 return; 6759 6760 ASC_DBG_PRT_CDB(2, scp->cmnd, scp->cmd_len); 6761 6762 ASC_STATS(boardp->shost, callback); 6763 6764 dma_unmap_single(boardp->dev, scp->SCp.dma_handle, 6765 SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE); 6766 /* 6767 * 'qdonep' contains the command's ending status. 6768 */ 6769 switch (qdonep->d3.done_stat) { 6770 case QD_NO_ERROR: 6771 ASC_DBG(2, "QD_NO_ERROR\n"); 6772 scp->result = 0; 6773 6774 /* 6775 * Check for an underrun condition. 6776 * 6777 * If there was no error and an underrun condition, then 6778 * return the number of underrun bytes. 6779 */ 6780 if (scsi_bufflen(scp) != 0 && qdonep->remain_bytes != 0 && 6781 qdonep->remain_bytes <= scsi_bufflen(scp)) { 6782 ASC_DBG(1, "underrun condition %u bytes\n", 6783 (unsigned)qdonep->remain_bytes); 6784 scsi_set_resid(scp, qdonep->remain_bytes); 6785 } 6786 break; 6787 6788 case QD_WITH_ERROR: 6789 ASC_DBG(2, "QD_WITH_ERROR\n"); 6790 switch (qdonep->d3.host_stat) { 6791 case QHSTA_NO_ERROR: 6792 if (qdonep->d3.scsi_stat == SAM_STAT_CHECK_CONDITION) { 6793 ASC_DBG(2, "SAM_STAT_CHECK_CONDITION\n"); 6794 ASC_DBG_PRT_SENSE(2, scp->sense_buffer, 6795 SCSI_SENSE_BUFFERSIZE); 6796 /* 6797 * Note: The 'status_byte()' macro used by 6798 * target drivers defined in scsi.h shifts the 6799 * status byte returned by host drivers right 6800 * by 1 bit. This is why target drivers also 6801 * use right shifted status byte definitions. 6802 * For instance target drivers use 6803 * CHECK_CONDITION, defined to 0x1, instead of 6804 * the SCSI defined check condition value of 6805 * 0x2. Host drivers are supposed to return 6806 * the status byte as it is defined by SCSI. 6807 */ 6808 scp->result = DRIVER_BYTE(DRIVER_SENSE) | 6809 STATUS_BYTE(qdonep->d3.scsi_stat); 6810 } else { 6811 scp->result = STATUS_BYTE(qdonep->d3.scsi_stat); 6812 } 6813 break; 6814 6815 default: 6816 /* QHSTA error occurred */ 6817 ASC_DBG(1, "host_stat 0x%x\n", qdonep->d3.host_stat); 6818 scp->result = HOST_BYTE(DID_BAD_TARGET); 6819 break; 6820 } 6821 break; 6822 6823 case QD_ABORTED_BY_HOST: 6824 ASC_DBG(1, "QD_ABORTED_BY_HOST\n"); 6825 scp->result = 6826 HOST_BYTE(DID_ABORT) | MSG_BYTE(qdonep->d3. 6827 scsi_msg) | 6828 STATUS_BYTE(qdonep->d3.scsi_stat); 6829 break; 6830 6831 default: 6832 ASC_DBG(1, "done_stat 0x%x\n", qdonep->d3.done_stat); 6833 scp->result = 6834 HOST_BYTE(DID_ERROR) | MSG_BYTE(qdonep->d3. 6835 scsi_msg) | 6836 STATUS_BYTE(qdonep->d3.scsi_stat); 6837 break; 6838 } 6839 6840 /* 6841 * If the 'init_tidmask' bit isn't already set for the target and the 6842 * current request finished normally, then set the bit for the target 6843 * to indicate that a device is present. 6844 */ 6845 if ((boardp->init_tidmask & ADV_TID_TO_TIDMASK(scp->device->id)) == 0 && 6846 qdonep->d3.done_stat == QD_NO_ERROR && 6847 qdonep->d3.host_stat == QHSTA_NO_ERROR) { 6848 boardp->init_tidmask |= ADV_TID_TO_TIDMASK(scp->device->id); 6849 } 6850 6851 asc_scsi_done(scp); 6852 } 6853 6854 static int AscIsrQDone(ASC_DVC_VAR *asc_dvc) 6855 { 6856 uchar next_qp; 6857 uchar n_q_used; 6858 uchar sg_list_qp; 6859 uchar sg_queue_cnt; 6860 uchar q_cnt; 6861 uchar done_q_tail; 6862 uchar tid_no; 6863 ASC_SCSI_BIT_ID_TYPE scsi_busy; 6864 ASC_SCSI_BIT_ID_TYPE target_id; 6865 PortAddr iop_base; 6866 ushort q_addr; 6867 ushort sg_q_addr; 6868 uchar cur_target_qng; 6869 ASC_QDONE_INFO scsiq_buf; 6870 ASC_QDONE_INFO *scsiq; 6871 bool false_overrun; 6872 6873 iop_base = asc_dvc->iop_base; 6874 n_q_used = 1; 6875 scsiq = (ASC_QDONE_INFO *)&scsiq_buf; 6876 done_q_tail = (uchar)AscGetVarDoneQTail(iop_base); 6877 q_addr = ASC_QNO_TO_QADDR(done_q_tail); 6878 next_qp = AscReadLramByte(iop_base, 6879 (ushort)(q_addr + (ushort)ASC_SCSIQ_B_FWD)); 6880 if (next_qp != ASC_QLINK_END) { 6881 AscPutVarDoneQTail(iop_base, next_qp); 6882 q_addr = ASC_QNO_TO_QADDR(next_qp); 6883 sg_queue_cnt = _AscCopyLramScsiDoneQ(iop_base, q_addr, scsiq, 6884 asc_dvc->max_dma_count); 6885 AscWriteLramByte(iop_base, 6886 (ushort)(q_addr + 6887 (ushort)ASC_SCSIQ_B_STATUS), 6888 (uchar)(scsiq-> 6889 q_status & (uchar)~(QS_READY | 6890 QS_ABORTED))); 6891 tid_no = ASC_TIX_TO_TID(scsiq->d2.target_ix); 6892 target_id = ASC_TIX_TO_TARGET_ID(scsiq->d2.target_ix); 6893 if ((scsiq->cntl & QC_SG_HEAD) != 0) { 6894 sg_q_addr = q_addr; 6895 sg_list_qp = next_qp; 6896 for (q_cnt = 0; q_cnt < sg_queue_cnt; q_cnt++) { 6897 sg_list_qp = AscReadLramByte(iop_base, 6898 (ushort)(sg_q_addr 6899 + (ushort) 6900 ASC_SCSIQ_B_FWD)); 6901 sg_q_addr = ASC_QNO_TO_QADDR(sg_list_qp); 6902 if (sg_list_qp == ASC_QLINK_END) { 6903 AscSetLibErrorCode(asc_dvc, 6904 ASCQ_ERR_SG_Q_LINKS); 6905 scsiq->d3.done_stat = QD_WITH_ERROR; 6906 scsiq->d3.host_stat = 6907 QHSTA_D_QDONE_SG_LIST_CORRUPTED; 6908 goto FATAL_ERR_QDONE; 6909 } 6910 AscWriteLramByte(iop_base, 6911 (ushort)(sg_q_addr + (ushort) 6912 ASC_SCSIQ_B_STATUS), 6913 QS_FREE); 6914 } 6915 n_q_used = sg_queue_cnt + 1; 6916 AscPutVarDoneQTail(iop_base, sg_list_qp); 6917 } 6918 if (asc_dvc->queue_full_or_busy & target_id) { 6919 cur_target_qng = AscReadLramByte(iop_base, 6920 (ushort)((ushort) 6921 ASC_QADR_BEG 6922 + (ushort) 6923 scsiq->d2. 6924 target_ix)); 6925 if (cur_target_qng < asc_dvc->max_dvc_qng[tid_no]) { 6926 scsi_busy = AscReadLramByte(iop_base, (ushort) 6927 ASCV_SCSIBUSY_B); 6928 scsi_busy &= ~target_id; 6929 AscWriteLramByte(iop_base, 6930 (ushort)ASCV_SCSIBUSY_B, 6931 scsi_busy); 6932 asc_dvc->queue_full_or_busy &= ~target_id; 6933 } 6934 } 6935 if (asc_dvc->cur_total_qng >= n_q_used) { 6936 asc_dvc->cur_total_qng -= n_q_used; 6937 if (asc_dvc->cur_dvc_qng[tid_no] != 0) { 6938 asc_dvc->cur_dvc_qng[tid_no]--; 6939 } 6940 } else { 6941 AscSetLibErrorCode(asc_dvc, ASCQ_ERR_CUR_QNG); 6942 scsiq->d3.done_stat = QD_WITH_ERROR; 6943 goto FATAL_ERR_QDONE; 6944 } 6945 if ((scsiq->d2.srb_tag == 0UL) || 6946 ((scsiq->q_status & QS_ABORTED) != 0)) { 6947 return (0x11); 6948 } else if (scsiq->q_status == QS_DONE) { 6949 /* 6950 * This is also curious. 6951 * false_overrun will _always_ be set to 'false' 6952 */ 6953 false_overrun = false; 6954 if (scsiq->extra_bytes != 0) { 6955 scsiq->remain_bytes += scsiq->extra_bytes; 6956 } 6957 if (scsiq->d3.done_stat == QD_WITH_ERROR) { 6958 if (scsiq->d3.host_stat == 6959 QHSTA_M_DATA_OVER_RUN) { 6960 if ((scsiq-> 6961 cntl & (QC_DATA_IN | QC_DATA_OUT)) 6962 == 0) { 6963 scsiq->d3.done_stat = 6964 QD_NO_ERROR; 6965 scsiq->d3.host_stat = 6966 QHSTA_NO_ERROR; 6967 } else if (false_overrun) { 6968 scsiq->d3.done_stat = 6969 QD_NO_ERROR; 6970 scsiq->d3.host_stat = 6971 QHSTA_NO_ERROR; 6972 } 6973 } else if (scsiq->d3.host_stat == 6974 QHSTA_M_HUNG_REQ_SCSI_BUS_RESET) { 6975 AscStopChip(iop_base); 6976 AscSetChipControl(iop_base, 6977 (uchar)(CC_SCSI_RESET 6978 | CC_HALT)); 6979 udelay(60); 6980 AscSetChipControl(iop_base, CC_HALT); 6981 AscSetChipStatus(iop_base, 6982 CIW_CLR_SCSI_RESET_INT); 6983 AscSetChipStatus(iop_base, 0); 6984 AscSetChipControl(iop_base, 0); 6985 } 6986 } 6987 if ((scsiq->cntl & QC_NO_CALLBACK) == 0) { 6988 asc_isr_callback(asc_dvc, scsiq); 6989 } else { 6990 if ((AscReadLramByte(iop_base, 6991 (ushort)(q_addr + (ushort) 6992 ASC_SCSIQ_CDB_BEG)) 6993 == START_STOP)) { 6994 asc_dvc->unit_not_ready &= ~target_id; 6995 if (scsiq->d3.done_stat != QD_NO_ERROR) { 6996 asc_dvc->start_motor &= 6997 ~target_id; 6998 } 6999 } 7000 } 7001 return (1); 7002 } else { 7003 AscSetLibErrorCode(asc_dvc, ASCQ_ERR_Q_STATUS); 7004 FATAL_ERR_QDONE: 7005 if ((scsiq->cntl & QC_NO_CALLBACK) == 0) { 7006 asc_isr_callback(asc_dvc, scsiq); 7007 } 7008 return (0x80); 7009 } 7010 } 7011 return (0); 7012 } 7013 7014 static int AscISR(ASC_DVC_VAR *asc_dvc) 7015 { 7016 ASC_CS_TYPE chipstat; 7017 PortAddr iop_base; 7018 ushort saved_ram_addr; 7019 uchar ctrl_reg; 7020 uchar saved_ctrl_reg; 7021 int int_pending; 7022 int status; 7023 uchar host_flag; 7024 7025 iop_base = asc_dvc->iop_base; 7026 int_pending = ASC_FALSE; 7027 7028 if (AscIsIntPending(iop_base) == 0) 7029 return int_pending; 7030 7031 if ((asc_dvc->init_state & ASC_INIT_STATE_END_LOAD_MC) == 0) { 7032 return ASC_ERROR; 7033 } 7034 if (asc_dvc->in_critical_cnt != 0) { 7035 AscSetLibErrorCode(asc_dvc, ASCQ_ERR_ISR_ON_CRITICAL); 7036 return ASC_ERROR; 7037 } 7038 if (asc_dvc->is_in_int) { 7039 AscSetLibErrorCode(asc_dvc, ASCQ_ERR_ISR_RE_ENTRY); 7040 return ASC_ERROR; 7041 } 7042 asc_dvc->is_in_int = true; 7043 ctrl_reg = AscGetChipControl(iop_base); 7044 saved_ctrl_reg = ctrl_reg & (~(CC_SCSI_RESET | CC_CHIP_RESET | 7045 CC_SINGLE_STEP | CC_DIAG | CC_TEST)); 7046 chipstat = AscGetChipStatus(iop_base); 7047 if (chipstat & CSW_SCSI_RESET_LATCH) { 7048 if (!(asc_dvc->bus_type & (ASC_IS_VL | ASC_IS_EISA))) { 7049 int i = 10; 7050 int_pending = ASC_TRUE; 7051 asc_dvc->sdtr_done = 0; 7052 saved_ctrl_reg &= (uchar)(~CC_HALT); 7053 while ((AscGetChipStatus(iop_base) & 7054 CSW_SCSI_RESET_ACTIVE) && (i-- > 0)) { 7055 mdelay(100); 7056 } 7057 AscSetChipControl(iop_base, (CC_CHIP_RESET | CC_HALT)); 7058 AscSetChipControl(iop_base, CC_HALT); 7059 AscSetChipStatus(iop_base, CIW_CLR_SCSI_RESET_INT); 7060 AscSetChipStatus(iop_base, 0); 7061 chipstat = AscGetChipStatus(iop_base); 7062 } 7063 } 7064 saved_ram_addr = AscGetChipLramAddr(iop_base); 7065 host_flag = AscReadLramByte(iop_base, 7066 ASCV_HOST_FLAG_B) & 7067 (uchar)(~ASC_HOST_FLAG_IN_ISR); 7068 AscWriteLramByte(iop_base, ASCV_HOST_FLAG_B, 7069 (uchar)(host_flag | (uchar)ASC_HOST_FLAG_IN_ISR)); 7070 if ((chipstat & CSW_INT_PENDING) || (int_pending)) { 7071 AscAckInterrupt(iop_base); 7072 int_pending = ASC_TRUE; 7073 if ((chipstat & CSW_HALTED) && (ctrl_reg & CC_SINGLE_STEP)) { 7074 AscIsrChipHalted(asc_dvc); 7075 saved_ctrl_reg &= (uchar)(~CC_HALT); 7076 } else { 7077 if ((asc_dvc->dvc_cntl & ASC_CNTL_INT_MULTI_Q) != 0) { 7078 while (((status = 7079 AscIsrQDone(asc_dvc)) & 0x01) != 0) { 7080 } 7081 } else { 7082 do { 7083 if ((status = 7084 AscIsrQDone(asc_dvc)) == 1) { 7085 break; 7086 } 7087 } while (status == 0x11); 7088 } 7089 if ((status & 0x80) != 0) 7090 int_pending = ASC_ERROR; 7091 } 7092 } 7093 AscWriteLramByte(iop_base, ASCV_HOST_FLAG_B, host_flag); 7094 AscSetChipLramAddr(iop_base, saved_ram_addr); 7095 AscSetChipControl(iop_base, saved_ctrl_reg); 7096 asc_dvc->is_in_int = false; 7097 return int_pending; 7098 } 7099 7100 /* 7101 * advansys_reset() 7102 * 7103 * Reset the host associated with the command 'scp'. 7104 * 7105 * This function runs its own thread. Interrupts must be blocked but 7106 * sleeping is allowed and no locking other than for host structures is 7107 * required. Returns SUCCESS or FAILED. 7108 */ 7109 static int advansys_reset(struct scsi_cmnd *scp) 7110 { 7111 struct Scsi_Host *shost = scp->device->host; 7112 struct asc_board *boardp = shost_priv(shost); 7113 unsigned long flags; 7114 int status; 7115 int ret = SUCCESS; 7116 7117 ASC_DBG(1, "0x%p\n", scp); 7118 7119 ASC_STATS(shost, reset); 7120 7121 scmd_printk(KERN_INFO, scp, "SCSI host reset started...\n"); 7122 7123 if (ASC_NARROW_BOARD(boardp)) { 7124 ASC_DVC_VAR *asc_dvc = &boardp->dvc_var.asc_dvc_var; 7125 7126 /* Reset the chip and SCSI bus. */ 7127 ASC_DBG(1, "before AscInitAsc1000Driver()\n"); 7128 status = AscInitAsc1000Driver(asc_dvc); 7129 7130 /* Refer to ASC_IERR_* definitions for meaning of 'err_code'. */ 7131 if (asc_dvc->err_code || !asc_dvc->overrun_dma) { 7132 scmd_printk(KERN_INFO, scp, "SCSI host reset error: " 7133 "0x%x, status: 0x%x\n", asc_dvc->err_code, 7134 status); 7135 ret = FAILED; 7136 } else if (status) { 7137 scmd_printk(KERN_INFO, scp, "SCSI host reset warning: " 7138 "0x%x\n", status); 7139 } else { 7140 scmd_printk(KERN_INFO, scp, "SCSI host reset " 7141 "successful\n"); 7142 } 7143 7144 ASC_DBG(1, "after AscInitAsc1000Driver()\n"); 7145 } else { 7146 /* 7147 * If the suggest reset bus flags are set, then reset the bus. 7148 * Otherwise only reset the device. 7149 */ 7150 ADV_DVC_VAR *adv_dvc = &boardp->dvc_var.adv_dvc_var; 7151 7152 /* 7153 * Reset the chip and SCSI bus. 7154 */ 7155 ASC_DBG(1, "before AdvResetChipAndSB()\n"); 7156 switch (AdvResetChipAndSB(adv_dvc)) { 7157 case ASC_TRUE: 7158 scmd_printk(KERN_INFO, scp, "SCSI host reset " 7159 "successful\n"); 7160 break; 7161 case ASC_FALSE: 7162 default: 7163 scmd_printk(KERN_INFO, scp, "SCSI host reset error\n"); 7164 ret = FAILED; 7165 break; 7166 } 7167 spin_lock_irqsave(shost->host_lock, flags); 7168 AdvISR(adv_dvc); 7169 spin_unlock_irqrestore(shost->host_lock, flags); 7170 } 7171 7172 ASC_DBG(1, "ret %d\n", ret); 7173 7174 return ret; 7175 } 7176 7177 /* 7178 * advansys_biosparam() 7179 * 7180 * Translate disk drive geometry if the "BIOS greater than 1 GB" 7181 * support is enabled for a drive. 7182 * 7183 * ip (information pointer) is an int array with the following definition: 7184 * ip[0]: heads 7185 * ip[1]: sectors 7186 * ip[2]: cylinders 7187 */ 7188 static int 7189 advansys_biosparam(struct scsi_device *sdev, struct block_device *bdev, 7190 sector_t capacity, int ip[]) 7191 { 7192 struct asc_board *boardp = shost_priv(sdev->host); 7193 7194 ASC_DBG(1, "begin\n"); 7195 ASC_STATS(sdev->host, biosparam); 7196 if (ASC_NARROW_BOARD(boardp)) { 7197 if ((boardp->dvc_var.asc_dvc_var.dvc_cntl & 7198 ASC_CNTL_BIOS_GT_1GB) && capacity > 0x200000) { 7199 ip[0] = 255; 7200 ip[1] = 63; 7201 } else { 7202 ip[0] = 64; 7203 ip[1] = 32; 7204 } 7205 } else { 7206 if ((boardp->dvc_var.adv_dvc_var.bios_ctrl & 7207 BIOS_CTRL_EXTENDED_XLAT) && capacity > 0x200000) { 7208 ip[0] = 255; 7209 ip[1] = 63; 7210 } else { 7211 ip[0] = 64; 7212 ip[1] = 32; 7213 } 7214 } 7215 ip[2] = (unsigned long)capacity / (ip[0] * ip[1]); 7216 ASC_DBG(1, "end\n"); 7217 return 0; 7218 } 7219 7220 /* 7221 * First-level interrupt handler. 7222 * 7223 * 'dev_id' is a pointer to the interrupting adapter's Scsi_Host. 7224 */ 7225 static irqreturn_t advansys_interrupt(int irq, void *dev_id) 7226 { 7227 struct Scsi_Host *shost = dev_id; 7228 struct asc_board *boardp = shost_priv(shost); 7229 irqreturn_t result = IRQ_NONE; 7230 unsigned long flags; 7231 7232 ASC_DBG(2, "boardp 0x%p\n", boardp); 7233 spin_lock_irqsave(shost->host_lock, flags); 7234 if (ASC_NARROW_BOARD(boardp)) { 7235 if (AscIsIntPending(shost->io_port)) { 7236 result = IRQ_HANDLED; 7237 ASC_STATS(shost, interrupt); 7238 ASC_DBG(1, "before AscISR()\n"); 7239 AscISR(&boardp->dvc_var.asc_dvc_var); 7240 } 7241 } else { 7242 ASC_DBG(1, "before AdvISR()\n"); 7243 if (AdvISR(&boardp->dvc_var.adv_dvc_var)) { 7244 result = IRQ_HANDLED; 7245 ASC_STATS(shost, interrupt); 7246 } 7247 } 7248 spin_unlock_irqrestore(shost->host_lock, flags); 7249 7250 ASC_DBG(1, "end\n"); 7251 return result; 7252 } 7253 7254 static bool AscHostReqRiscHalt(PortAddr iop_base) 7255 { 7256 int count = 0; 7257 bool sta = false; 7258 uchar saved_stop_code; 7259 7260 if (AscIsChipHalted(iop_base)) 7261 return true; 7262 saved_stop_code = AscReadLramByte(iop_base, ASCV_STOP_CODE_B); 7263 AscWriteLramByte(iop_base, ASCV_STOP_CODE_B, 7264 ASC_STOP_HOST_REQ_RISC_HALT | ASC_STOP_REQ_RISC_STOP); 7265 do { 7266 if (AscIsChipHalted(iop_base)) { 7267 sta = true; 7268 break; 7269 } 7270 mdelay(100); 7271 } while (count++ < 20); 7272 AscWriteLramByte(iop_base, ASCV_STOP_CODE_B, saved_stop_code); 7273 return sta; 7274 } 7275 7276 static bool 7277 AscSetRunChipSynRegAtID(PortAddr iop_base, uchar tid_no, uchar sdtr_data) 7278 { 7279 bool sta = false; 7280 7281 if (AscHostReqRiscHalt(iop_base)) { 7282 sta = AscSetChipSynRegAtID(iop_base, tid_no, sdtr_data); 7283 AscStartChip(iop_base); 7284 } 7285 return sta; 7286 } 7287 7288 static void AscAsyncFix(ASC_DVC_VAR *asc_dvc, struct scsi_device *sdev) 7289 { 7290 char type = sdev->type; 7291 ASC_SCSI_BIT_ID_TYPE tid_bits = 1 << sdev->id; 7292 7293 if (!(asc_dvc->bug_fix_cntl & ASC_BUG_FIX_ASYN_USE_SYN)) 7294 return; 7295 if (asc_dvc->init_sdtr & tid_bits) 7296 return; 7297 7298 if ((type == TYPE_ROM) && (strncmp(sdev->vendor, "HP ", 3) == 0)) 7299 asc_dvc->pci_fix_asyn_xfer_always |= tid_bits; 7300 7301 asc_dvc->pci_fix_asyn_xfer |= tid_bits; 7302 if ((type == TYPE_PROCESSOR) || (type == TYPE_SCANNER) || 7303 (type == TYPE_ROM) || (type == TYPE_TAPE)) 7304 asc_dvc->pci_fix_asyn_xfer &= ~tid_bits; 7305 7306 if (asc_dvc->pci_fix_asyn_xfer & tid_bits) 7307 AscSetRunChipSynRegAtID(asc_dvc->iop_base, sdev->id, 7308 ASYN_SDTR_DATA_FIX_PCI_REV_AB); 7309 } 7310 7311 static void 7312 advansys_narrow_slave_configure(struct scsi_device *sdev, ASC_DVC_VAR *asc_dvc) 7313 { 7314 ASC_SCSI_BIT_ID_TYPE tid_bit = 1 << sdev->id; 7315 ASC_SCSI_BIT_ID_TYPE orig_use_tagged_qng = asc_dvc->use_tagged_qng; 7316 7317 if (sdev->lun == 0) { 7318 ASC_SCSI_BIT_ID_TYPE orig_init_sdtr = asc_dvc->init_sdtr; 7319 if ((asc_dvc->cfg->sdtr_enable & tid_bit) && sdev->sdtr) { 7320 asc_dvc->init_sdtr |= tid_bit; 7321 } else { 7322 asc_dvc->init_sdtr &= ~tid_bit; 7323 } 7324 7325 if (orig_init_sdtr != asc_dvc->init_sdtr) 7326 AscAsyncFix(asc_dvc, sdev); 7327 } 7328 7329 if (sdev->tagged_supported) { 7330 if (asc_dvc->cfg->cmd_qng_enabled & tid_bit) { 7331 if (sdev->lun == 0) { 7332 asc_dvc->cfg->can_tagged_qng |= tid_bit; 7333 asc_dvc->use_tagged_qng |= tid_bit; 7334 } 7335 scsi_change_queue_depth(sdev, 7336 asc_dvc->max_dvc_qng[sdev->id]); 7337 } 7338 } else { 7339 if (sdev->lun == 0) { 7340 asc_dvc->cfg->can_tagged_qng &= ~tid_bit; 7341 asc_dvc->use_tagged_qng &= ~tid_bit; 7342 } 7343 } 7344 7345 if ((sdev->lun == 0) && 7346 (orig_use_tagged_qng != asc_dvc->use_tagged_qng)) { 7347 AscWriteLramByte(asc_dvc->iop_base, ASCV_DISC_ENABLE_B, 7348 asc_dvc->cfg->disc_enable); 7349 AscWriteLramByte(asc_dvc->iop_base, ASCV_USE_TAGGED_QNG_B, 7350 asc_dvc->use_tagged_qng); 7351 AscWriteLramByte(asc_dvc->iop_base, ASCV_CAN_TAGGED_QNG_B, 7352 asc_dvc->cfg->can_tagged_qng); 7353 7354 asc_dvc->max_dvc_qng[sdev->id] = 7355 asc_dvc->cfg->max_tag_qng[sdev->id]; 7356 AscWriteLramByte(asc_dvc->iop_base, 7357 (ushort)(ASCV_MAX_DVC_QNG_BEG + sdev->id), 7358 asc_dvc->max_dvc_qng[sdev->id]); 7359 } 7360 } 7361 7362 /* 7363 * Wide Transfers 7364 * 7365 * If the EEPROM enabled WDTR for the device and the device supports wide 7366 * bus (16 bit) transfers, then turn on the device's 'wdtr_able' bit and 7367 * write the new value to the microcode. 7368 */ 7369 static void 7370 advansys_wide_enable_wdtr(AdvPortAddr iop_base, unsigned short tidmask) 7371 { 7372 unsigned short cfg_word; 7373 AdvReadWordLram(iop_base, ASC_MC_WDTR_ABLE, cfg_word); 7374 if ((cfg_word & tidmask) != 0) 7375 return; 7376 7377 cfg_word |= tidmask; 7378 AdvWriteWordLram(iop_base, ASC_MC_WDTR_ABLE, cfg_word); 7379 7380 /* 7381 * Clear the microcode SDTR and WDTR negotiation done indicators for 7382 * the target to cause it to negotiate with the new setting set above. 7383 * WDTR when accepted causes the target to enter asynchronous mode, so 7384 * SDTR must be negotiated. 7385 */ 7386 AdvReadWordLram(iop_base, ASC_MC_SDTR_DONE, cfg_word); 7387 cfg_word &= ~tidmask; 7388 AdvWriteWordLram(iop_base, ASC_MC_SDTR_DONE, cfg_word); 7389 AdvReadWordLram(iop_base, ASC_MC_WDTR_DONE, cfg_word); 7390 cfg_word &= ~tidmask; 7391 AdvWriteWordLram(iop_base, ASC_MC_WDTR_DONE, cfg_word); 7392 } 7393 7394 /* 7395 * Synchronous Transfers 7396 * 7397 * If the EEPROM enabled SDTR for the device and the device 7398 * supports synchronous transfers, then turn on the device's 7399 * 'sdtr_able' bit. Write the new value to the microcode. 7400 */ 7401 static void 7402 advansys_wide_enable_sdtr(AdvPortAddr iop_base, unsigned short tidmask) 7403 { 7404 unsigned short cfg_word; 7405 AdvReadWordLram(iop_base, ASC_MC_SDTR_ABLE, cfg_word); 7406 if ((cfg_word & tidmask) != 0) 7407 return; 7408 7409 cfg_word |= tidmask; 7410 AdvWriteWordLram(iop_base, ASC_MC_SDTR_ABLE, cfg_word); 7411 7412 /* 7413 * Clear the microcode "SDTR negotiation" done indicator for the 7414 * target to cause it to negotiate with the new setting set above. 7415 */ 7416 AdvReadWordLram(iop_base, ASC_MC_SDTR_DONE, cfg_word); 7417 cfg_word &= ~tidmask; 7418 AdvWriteWordLram(iop_base, ASC_MC_SDTR_DONE, cfg_word); 7419 } 7420 7421 /* 7422 * PPR (Parallel Protocol Request) Capable 7423 * 7424 * If the device supports DT mode, then it must be PPR capable. 7425 * The PPR message will be used in place of the SDTR and WDTR 7426 * messages to negotiate synchronous speed and offset, transfer 7427 * width, and protocol options. 7428 */ 7429 static void advansys_wide_enable_ppr(ADV_DVC_VAR *adv_dvc, 7430 AdvPortAddr iop_base, unsigned short tidmask) 7431 { 7432 AdvReadWordLram(iop_base, ASC_MC_PPR_ABLE, adv_dvc->ppr_able); 7433 adv_dvc->ppr_able |= tidmask; 7434 AdvWriteWordLram(iop_base, ASC_MC_PPR_ABLE, adv_dvc->ppr_able); 7435 } 7436 7437 static void 7438 advansys_wide_slave_configure(struct scsi_device *sdev, ADV_DVC_VAR *adv_dvc) 7439 { 7440 AdvPortAddr iop_base = adv_dvc->iop_base; 7441 unsigned short tidmask = 1 << sdev->id; 7442 7443 if (sdev->lun == 0) { 7444 /* 7445 * Handle WDTR, SDTR, and Tag Queuing. If the feature 7446 * is enabled in the EEPROM and the device supports the 7447 * feature, then enable it in the microcode. 7448 */ 7449 7450 if ((adv_dvc->wdtr_able & tidmask) && sdev->wdtr) 7451 advansys_wide_enable_wdtr(iop_base, tidmask); 7452 if ((adv_dvc->sdtr_able & tidmask) && sdev->sdtr) 7453 advansys_wide_enable_sdtr(iop_base, tidmask); 7454 if (adv_dvc->chip_type == ADV_CHIP_ASC38C1600 && sdev->ppr) 7455 advansys_wide_enable_ppr(adv_dvc, iop_base, tidmask); 7456 7457 /* 7458 * Tag Queuing is disabled for the BIOS which runs in polled 7459 * mode and would see no benefit from Tag Queuing. Also by 7460 * disabling Tag Queuing in the BIOS devices with Tag Queuing 7461 * bugs will at least work with the BIOS. 7462 */ 7463 if ((adv_dvc->tagqng_able & tidmask) && 7464 sdev->tagged_supported) { 7465 unsigned short cfg_word; 7466 AdvReadWordLram(iop_base, ASC_MC_TAGQNG_ABLE, cfg_word); 7467 cfg_word |= tidmask; 7468 AdvWriteWordLram(iop_base, ASC_MC_TAGQNG_ABLE, 7469 cfg_word); 7470 AdvWriteByteLram(iop_base, 7471 ASC_MC_NUMBER_OF_MAX_CMD + sdev->id, 7472 adv_dvc->max_dvc_qng); 7473 } 7474 } 7475 7476 if ((adv_dvc->tagqng_able & tidmask) && sdev->tagged_supported) 7477 scsi_change_queue_depth(sdev, adv_dvc->max_dvc_qng); 7478 } 7479 7480 /* 7481 * Set the number of commands to queue per device for the 7482 * specified host adapter. 7483 */ 7484 static int advansys_slave_configure(struct scsi_device *sdev) 7485 { 7486 struct asc_board *boardp = shost_priv(sdev->host); 7487 7488 if (ASC_NARROW_BOARD(boardp)) 7489 advansys_narrow_slave_configure(sdev, 7490 &boardp->dvc_var.asc_dvc_var); 7491 else 7492 advansys_wide_slave_configure(sdev, 7493 &boardp->dvc_var.adv_dvc_var); 7494 7495 return 0; 7496 } 7497 7498 static __le32 asc_get_sense_buffer_dma(struct scsi_cmnd *scp) 7499 { 7500 struct asc_board *board = shost_priv(scp->device->host); 7501 7502 scp->SCp.dma_handle = dma_map_single(board->dev, scp->sense_buffer, 7503 SCSI_SENSE_BUFFERSIZE, 7504 DMA_FROM_DEVICE); 7505 if (dma_mapping_error(board->dev, scp->SCp.dma_handle)) { 7506 ASC_DBG(1, "failed to map sense buffer\n"); 7507 return 0; 7508 } 7509 return cpu_to_le32(scp->SCp.dma_handle); 7510 } 7511 7512 static int asc_build_req(struct asc_board *boardp, struct scsi_cmnd *scp, 7513 struct asc_scsi_q *asc_scsi_q) 7514 { 7515 struct asc_dvc_var *asc_dvc = &boardp->dvc_var.asc_dvc_var; 7516 int use_sg; 7517 u32 srb_tag; 7518 7519 memset(asc_scsi_q, 0, sizeof(*asc_scsi_q)); 7520 7521 /* 7522 * Set the srb_tag to the command tag + 1, as 7523 * srb_tag '0' is used internally by the chip. 7524 */ 7525 srb_tag = scp->request->tag + 1; 7526 asc_scsi_q->q2.srb_tag = srb_tag; 7527 7528 /* 7529 * Build the ASC_SCSI_Q request. 7530 */ 7531 asc_scsi_q->cdbptr = &scp->cmnd[0]; 7532 asc_scsi_q->q2.cdb_len = scp->cmd_len; 7533 asc_scsi_q->q1.target_id = ASC_TID_TO_TARGET_ID(scp->device->id); 7534 asc_scsi_q->q1.target_lun = scp->device->lun; 7535 asc_scsi_q->q2.target_ix = 7536 ASC_TIDLUN_TO_IX(scp->device->id, scp->device->lun); 7537 asc_scsi_q->q1.sense_addr = asc_get_sense_buffer_dma(scp); 7538 asc_scsi_q->q1.sense_len = SCSI_SENSE_BUFFERSIZE; 7539 if (!asc_scsi_q->q1.sense_addr) 7540 return ASC_BUSY; 7541 7542 /* 7543 * If there are any outstanding requests for the current target, 7544 * then every 255th request send an ORDERED request. This heuristic 7545 * tries to retain the benefit of request sorting while preventing 7546 * request starvation. 255 is the max number of tags or pending commands 7547 * a device may have outstanding. 7548 * 7549 * The request count is incremented below for every successfully 7550 * started request. 7551 * 7552 */ 7553 if ((asc_dvc->cur_dvc_qng[scp->device->id] > 0) && 7554 (boardp->reqcnt[scp->device->id] % 255) == 0) { 7555 asc_scsi_q->q2.tag_code = ORDERED_QUEUE_TAG; 7556 } else { 7557 asc_scsi_q->q2.tag_code = SIMPLE_QUEUE_TAG; 7558 } 7559 7560 /* Build ASC_SCSI_Q */ 7561 use_sg = scsi_dma_map(scp); 7562 if (use_sg < 0) { 7563 ASC_DBG(1, "failed to map sglist\n"); 7564 return ASC_BUSY; 7565 } else if (use_sg > 0) { 7566 int sgcnt; 7567 struct scatterlist *slp; 7568 struct asc_sg_head *asc_sg_head; 7569 7570 if (use_sg > scp->device->host->sg_tablesize) { 7571 scmd_printk(KERN_ERR, scp, "use_sg %d > " 7572 "sg_tablesize %d\n", use_sg, 7573 scp->device->host->sg_tablesize); 7574 scsi_dma_unmap(scp); 7575 scp->result = HOST_BYTE(DID_ERROR); 7576 return ASC_ERROR; 7577 } 7578 7579 asc_sg_head = kzalloc(sizeof(asc_scsi_q->sg_head) + 7580 use_sg * sizeof(struct asc_sg_list), GFP_ATOMIC); 7581 if (!asc_sg_head) { 7582 scsi_dma_unmap(scp); 7583 scp->result = HOST_BYTE(DID_SOFT_ERROR); 7584 return ASC_ERROR; 7585 } 7586 7587 asc_scsi_q->q1.cntl |= QC_SG_HEAD; 7588 asc_scsi_q->sg_head = asc_sg_head; 7589 asc_scsi_q->q1.data_cnt = 0; 7590 asc_scsi_q->q1.data_addr = 0; 7591 /* This is a byte value, otherwise it would need to be swapped. */ 7592 asc_sg_head->entry_cnt = asc_scsi_q->q1.sg_queue_cnt = use_sg; 7593 ASC_STATS_ADD(scp->device->host, xfer_elem, 7594 asc_sg_head->entry_cnt); 7595 7596 /* 7597 * Convert scatter-gather list into ASC_SG_HEAD list. 7598 */ 7599 scsi_for_each_sg(scp, slp, use_sg, sgcnt) { 7600 asc_sg_head->sg_list[sgcnt].addr = 7601 cpu_to_le32(sg_dma_address(slp)); 7602 asc_sg_head->sg_list[sgcnt].bytes = 7603 cpu_to_le32(sg_dma_len(slp)); 7604 ASC_STATS_ADD(scp->device->host, xfer_sect, 7605 DIV_ROUND_UP(sg_dma_len(slp), 512)); 7606 } 7607 } 7608 7609 ASC_STATS(scp->device->host, xfer_cnt); 7610 7611 ASC_DBG_PRT_ASC_SCSI_Q(2, asc_scsi_q); 7612 ASC_DBG_PRT_CDB(1, scp->cmnd, scp->cmd_len); 7613 7614 return ASC_NOERROR; 7615 } 7616 7617 /* 7618 * Build scatter-gather list for Adv Library (Wide Board). 7619 * 7620 * Additional ADV_SG_BLOCK structures will need to be allocated 7621 * if the total number of scatter-gather elements exceeds 7622 * NO_OF_SG_PER_BLOCK (15). The ADV_SG_BLOCK structures are 7623 * assumed to be physically contiguous. 7624 * 7625 * Return: 7626 * ADV_SUCCESS(1) - SG List successfully created 7627 * ADV_ERROR(-1) - SG List creation failed 7628 */ 7629 static int 7630 adv_get_sglist(struct asc_board *boardp, adv_req_t *reqp, 7631 ADV_SCSI_REQ_Q *scsiqp, struct scsi_cmnd *scp, int use_sg) 7632 { 7633 adv_sgblk_t *sgblkp, *prev_sgblkp; 7634 struct scatterlist *slp; 7635 int sg_elem_cnt; 7636 ADV_SG_BLOCK *sg_block, *prev_sg_block; 7637 dma_addr_t sgblk_paddr; 7638 int i; 7639 7640 slp = scsi_sglist(scp); 7641 sg_elem_cnt = use_sg; 7642 prev_sgblkp = NULL; 7643 prev_sg_block = NULL; 7644 reqp->sgblkp = NULL; 7645 7646 for (;;) { 7647 /* 7648 * Allocate a 'adv_sgblk_t' structure from the board free 7649 * list. One 'adv_sgblk_t' structure holds NO_OF_SG_PER_BLOCK 7650 * (15) scatter-gather elements. 7651 */ 7652 sgblkp = dma_pool_alloc(boardp->adv_sgblk_pool, GFP_ATOMIC, 7653 &sgblk_paddr); 7654 if (!sgblkp) { 7655 ASC_DBG(1, "no free adv_sgblk_t\n"); 7656 ASC_STATS(scp->device->host, adv_build_nosg); 7657 7658 /* 7659 * Allocation failed. Free 'adv_sgblk_t' structures 7660 * already allocated for the request. 7661 */ 7662 while ((sgblkp = reqp->sgblkp) != NULL) { 7663 /* Remove 'sgblkp' from the request list. */ 7664 reqp->sgblkp = sgblkp->next_sgblkp; 7665 sgblkp->next_sgblkp = NULL; 7666 dma_pool_free(boardp->adv_sgblk_pool, sgblkp, 7667 sgblkp->sg_addr); 7668 } 7669 return ASC_BUSY; 7670 } 7671 /* Complete 'adv_sgblk_t' board allocation. */ 7672 sgblkp->sg_addr = sgblk_paddr; 7673 sgblkp->next_sgblkp = NULL; 7674 sg_block = &sgblkp->sg_block; 7675 7676 /* 7677 * Check if this is the first 'adv_sgblk_t' for the 7678 * request. 7679 */ 7680 if (reqp->sgblkp == NULL) { 7681 /* Request's first scatter-gather block. */ 7682 reqp->sgblkp = sgblkp; 7683 7684 /* 7685 * Set ADV_SCSI_REQ_T ADV_SG_BLOCK virtual and physical 7686 * address pointers. 7687 */ 7688 scsiqp->sg_list_ptr = sg_block; 7689 scsiqp->sg_real_addr = cpu_to_le32(sgblk_paddr); 7690 } else { 7691 /* Request's second or later scatter-gather block. */ 7692 prev_sgblkp->next_sgblkp = sgblkp; 7693 7694 /* 7695 * Point the previous ADV_SG_BLOCK structure to 7696 * the newly allocated ADV_SG_BLOCK structure. 7697 */ 7698 prev_sg_block->sg_ptr = cpu_to_le32(sgblk_paddr); 7699 } 7700 7701 for (i = 0; i < NO_OF_SG_PER_BLOCK; i++) { 7702 sg_block->sg_list[i].sg_addr = 7703 cpu_to_le32(sg_dma_address(slp)); 7704 sg_block->sg_list[i].sg_count = 7705 cpu_to_le32(sg_dma_len(slp)); 7706 ASC_STATS_ADD(scp->device->host, xfer_sect, 7707 DIV_ROUND_UP(sg_dma_len(slp), 512)); 7708 7709 if (--sg_elem_cnt == 0) { 7710 /* 7711 * Last ADV_SG_BLOCK and scatter-gather entry. 7712 */ 7713 sg_block->sg_cnt = i + 1; 7714 sg_block->sg_ptr = 0L; /* Last ADV_SG_BLOCK in list. */ 7715 return ADV_SUCCESS; 7716 } 7717 slp++; 7718 } 7719 sg_block->sg_cnt = NO_OF_SG_PER_BLOCK; 7720 prev_sg_block = sg_block; 7721 prev_sgblkp = sgblkp; 7722 } 7723 } 7724 7725 /* 7726 * Build a request structure for the Adv Library (Wide Board). 7727 * 7728 * If an adv_req_t can not be allocated to issue the request, 7729 * then return ASC_BUSY. If an error occurs, then return ASC_ERROR. 7730 * 7731 * Multi-byte fields in the ADV_SCSI_REQ_Q that are used by the 7732 * microcode for DMA addresses or math operations are byte swapped 7733 * to little-endian order. 7734 */ 7735 static int 7736 adv_build_req(struct asc_board *boardp, struct scsi_cmnd *scp, 7737 adv_req_t **adv_reqpp) 7738 { 7739 u32 srb_tag = scp->request->tag; 7740 adv_req_t *reqp; 7741 ADV_SCSI_REQ_Q *scsiqp; 7742 int ret; 7743 int use_sg; 7744 dma_addr_t sense_addr; 7745 7746 /* 7747 * Allocate an adv_req_t structure from the board to execute 7748 * the command. 7749 */ 7750 reqp = &boardp->adv_reqp[srb_tag]; 7751 if (reqp->cmndp && reqp->cmndp != scp ) { 7752 ASC_DBG(1, "no free adv_req_t\n"); 7753 ASC_STATS(scp->device->host, adv_build_noreq); 7754 return ASC_BUSY; 7755 } 7756 7757 reqp->req_addr = boardp->adv_reqp_addr + (srb_tag * sizeof(adv_req_t)); 7758 7759 scsiqp = &reqp->scsi_req_q; 7760 7761 /* 7762 * Initialize the structure. 7763 */ 7764 scsiqp->cntl = scsiqp->scsi_cntl = scsiqp->done_status = 0; 7765 7766 /* 7767 * Set the srb_tag to the command tag. 7768 */ 7769 scsiqp->srb_tag = srb_tag; 7770 7771 /* 7772 * Set 'host_scribble' to point to the adv_req_t structure. 7773 */ 7774 reqp->cmndp = scp; 7775 scp->host_scribble = (void *)reqp; 7776 7777 /* 7778 * Build the ADV_SCSI_REQ_Q request. 7779 */ 7780 7781 /* Set CDB length and copy it to the request structure. */ 7782 scsiqp->cdb_len = scp->cmd_len; 7783 /* Copy first 12 CDB bytes to cdb[]. */ 7784 memcpy(scsiqp->cdb, scp->cmnd, scp->cmd_len < 12 ? scp->cmd_len : 12); 7785 /* Copy last 4 CDB bytes, if present, to cdb16[]. */ 7786 if (scp->cmd_len > 12) { 7787 int cdb16_len = scp->cmd_len - 12; 7788 7789 memcpy(scsiqp->cdb16, &scp->cmnd[12], cdb16_len); 7790 } 7791 7792 scsiqp->target_id = scp->device->id; 7793 scsiqp->target_lun = scp->device->lun; 7794 7795 sense_addr = dma_map_single(boardp->dev, scp->sense_buffer, 7796 SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE); 7797 if (dma_mapping_error(boardp->dev, sense_addr)) { 7798 ASC_DBG(1, "failed to map sense buffer\n"); 7799 ASC_STATS(scp->device->host, adv_build_noreq); 7800 return ASC_BUSY; 7801 } 7802 scsiqp->sense_addr = cpu_to_le32(sense_addr); 7803 scsiqp->sense_len = SCSI_SENSE_BUFFERSIZE; 7804 7805 /* Build ADV_SCSI_REQ_Q */ 7806 7807 use_sg = scsi_dma_map(scp); 7808 if (use_sg < 0) { 7809 ASC_DBG(1, "failed to map SG list\n"); 7810 ASC_STATS(scp->device->host, adv_build_noreq); 7811 return ASC_BUSY; 7812 } else if (use_sg == 0) { 7813 /* Zero-length transfer */ 7814 reqp->sgblkp = NULL; 7815 scsiqp->data_cnt = 0; 7816 7817 scsiqp->data_addr = 0; 7818 scsiqp->sg_list_ptr = NULL; 7819 scsiqp->sg_real_addr = 0; 7820 } else { 7821 if (use_sg > ADV_MAX_SG_LIST) { 7822 scmd_printk(KERN_ERR, scp, "use_sg %d > " 7823 "ADV_MAX_SG_LIST %d\n", use_sg, 7824 scp->device->host->sg_tablesize); 7825 scsi_dma_unmap(scp); 7826 scp->result = HOST_BYTE(DID_ERROR); 7827 reqp->cmndp = NULL; 7828 scp->host_scribble = NULL; 7829 7830 return ASC_ERROR; 7831 } 7832 7833 scsiqp->data_cnt = cpu_to_le32(scsi_bufflen(scp)); 7834 7835 ret = adv_get_sglist(boardp, reqp, scsiqp, scp, use_sg); 7836 if (ret != ADV_SUCCESS) { 7837 scsi_dma_unmap(scp); 7838 scp->result = HOST_BYTE(DID_ERROR); 7839 reqp->cmndp = NULL; 7840 scp->host_scribble = NULL; 7841 7842 return ret; 7843 } 7844 7845 ASC_STATS_ADD(scp->device->host, xfer_elem, use_sg); 7846 } 7847 7848 ASC_STATS(scp->device->host, xfer_cnt); 7849 7850 ASC_DBG_PRT_ADV_SCSI_REQ_Q(2, scsiqp); 7851 ASC_DBG_PRT_CDB(1, scp->cmnd, scp->cmd_len); 7852 7853 *adv_reqpp = reqp; 7854 7855 return ASC_NOERROR; 7856 } 7857 7858 static int AscSgListToQueue(int sg_list) 7859 { 7860 int n_sg_list_qs; 7861 7862 n_sg_list_qs = ((sg_list - 1) / ASC_SG_LIST_PER_Q); 7863 if (((sg_list - 1) % ASC_SG_LIST_PER_Q) != 0) 7864 n_sg_list_qs++; 7865 return n_sg_list_qs + 1; 7866 } 7867 7868 static uint 7869 AscGetNumOfFreeQueue(ASC_DVC_VAR *asc_dvc, uchar target_ix, uchar n_qs) 7870 { 7871 uint cur_used_qs; 7872 uint cur_free_qs; 7873 ASC_SCSI_BIT_ID_TYPE target_id; 7874 uchar tid_no; 7875 7876 target_id = ASC_TIX_TO_TARGET_ID(target_ix); 7877 tid_no = ASC_TIX_TO_TID(target_ix); 7878 if ((asc_dvc->unit_not_ready & target_id) || 7879 (asc_dvc->queue_full_or_busy & target_id)) { 7880 return 0; 7881 } 7882 if (n_qs == 1) { 7883 cur_used_qs = (uint) asc_dvc->cur_total_qng + 7884 (uint) asc_dvc->last_q_shortage + (uint) ASC_MIN_FREE_Q; 7885 } else { 7886 cur_used_qs = (uint) asc_dvc->cur_total_qng + 7887 (uint) ASC_MIN_FREE_Q; 7888 } 7889 if ((uint) (cur_used_qs + n_qs) <= (uint) asc_dvc->max_total_qng) { 7890 cur_free_qs = (uint) asc_dvc->max_total_qng - cur_used_qs; 7891 if (asc_dvc->cur_dvc_qng[tid_no] >= 7892 asc_dvc->max_dvc_qng[tid_no]) { 7893 return 0; 7894 } 7895 return cur_free_qs; 7896 } 7897 if (n_qs > 1) { 7898 if ((n_qs > asc_dvc->last_q_shortage) 7899 && (n_qs <= (asc_dvc->max_total_qng - ASC_MIN_FREE_Q))) { 7900 asc_dvc->last_q_shortage = n_qs; 7901 } 7902 } 7903 return 0; 7904 } 7905 7906 static uchar AscAllocFreeQueue(PortAddr iop_base, uchar free_q_head) 7907 { 7908 ushort q_addr; 7909 uchar next_qp; 7910 uchar q_status; 7911 7912 q_addr = ASC_QNO_TO_QADDR(free_q_head); 7913 q_status = (uchar)AscReadLramByte(iop_base, 7914 (ushort)(q_addr + 7915 ASC_SCSIQ_B_STATUS)); 7916 next_qp = AscReadLramByte(iop_base, (ushort)(q_addr + ASC_SCSIQ_B_FWD)); 7917 if (((q_status & QS_READY) == 0) && (next_qp != ASC_QLINK_END)) 7918 return next_qp; 7919 return ASC_QLINK_END; 7920 } 7921 7922 static uchar 7923 AscAllocMultipleFreeQueue(PortAddr iop_base, uchar free_q_head, uchar n_free_q) 7924 { 7925 uchar i; 7926 7927 for (i = 0; i < n_free_q; i++) { 7928 free_q_head = AscAllocFreeQueue(iop_base, free_q_head); 7929 if (free_q_head == ASC_QLINK_END) 7930 break; 7931 } 7932 return free_q_head; 7933 } 7934 7935 /* 7936 * void 7937 * DvcPutScsiQ(PortAddr iop_base, ushort s_addr, uchar *outbuf, int words) 7938 * 7939 * Calling/Exit State: 7940 * none 7941 * 7942 * Description: 7943 * Output an ASC_SCSI_Q structure to the chip 7944 */ 7945 static void 7946 DvcPutScsiQ(PortAddr iop_base, ushort s_addr, uchar *outbuf, int words) 7947 { 7948 int i; 7949 7950 ASC_DBG_PRT_HEX(2, "DvcPutScsiQ", outbuf, 2 * words); 7951 AscSetChipLramAddr(iop_base, s_addr); 7952 for (i = 0; i < 2 * words; i += 2) { 7953 if (i == 4 || i == 20) { 7954 continue; 7955 } 7956 outpw(iop_base + IOP_RAM_DATA, 7957 ((ushort)outbuf[i + 1] << 8) | outbuf[i]); 7958 } 7959 } 7960 7961 static int AscPutReadyQueue(ASC_DVC_VAR *asc_dvc, ASC_SCSI_Q *scsiq, uchar q_no) 7962 { 7963 ushort q_addr; 7964 uchar tid_no; 7965 uchar sdtr_data; 7966 uchar syn_period_ix; 7967 uchar syn_offset; 7968 PortAddr iop_base; 7969 7970 iop_base = asc_dvc->iop_base; 7971 if (((asc_dvc->init_sdtr & scsiq->q1.target_id) != 0) && 7972 ((asc_dvc->sdtr_done & scsiq->q1.target_id) == 0)) { 7973 tid_no = ASC_TIX_TO_TID(scsiq->q2.target_ix); 7974 sdtr_data = AscGetMCodeInitSDTRAtID(iop_base, tid_no); 7975 syn_period_ix = 7976 (sdtr_data >> 4) & (asc_dvc->max_sdtr_index - 1); 7977 syn_offset = sdtr_data & ASC_SYN_MAX_OFFSET; 7978 AscMsgOutSDTR(asc_dvc, 7979 asc_dvc->sdtr_period_tbl[syn_period_ix], 7980 syn_offset); 7981 scsiq->q1.cntl |= QC_MSG_OUT; 7982 } 7983 q_addr = ASC_QNO_TO_QADDR(q_no); 7984 if ((scsiq->q1.target_id & asc_dvc->use_tagged_qng) == 0) { 7985 scsiq->q2.tag_code &= ~SIMPLE_QUEUE_TAG; 7986 } 7987 scsiq->q1.status = QS_FREE; 7988 AscMemWordCopyPtrToLram(iop_base, 7989 q_addr + ASC_SCSIQ_CDB_BEG, 7990 (uchar *)scsiq->cdbptr, scsiq->q2.cdb_len >> 1); 7991 7992 DvcPutScsiQ(iop_base, 7993 q_addr + ASC_SCSIQ_CPY_BEG, 7994 (uchar *)&scsiq->q1.cntl, 7995 ((sizeof(ASC_SCSIQ_1) + sizeof(ASC_SCSIQ_2)) / 2) - 1); 7996 AscWriteLramWord(iop_base, 7997 (ushort)(q_addr + (ushort)ASC_SCSIQ_B_STATUS), 7998 (ushort)(((ushort)scsiq->q1. 7999 q_no << 8) | (ushort)QS_READY)); 8000 return 1; 8001 } 8002 8003 static int 8004 AscPutReadySgListQueue(ASC_DVC_VAR *asc_dvc, ASC_SCSI_Q *scsiq, uchar q_no) 8005 { 8006 int sta; 8007 int i; 8008 ASC_SG_HEAD *sg_head; 8009 ASC_SG_LIST_Q scsi_sg_q; 8010 __le32 saved_data_addr; 8011 __le32 saved_data_cnt; 8012 PortAddr iop_base; 8013 ushort sg_list_dwords; 8014 ushort sg_index; 8015 ushort sg_entry_cnt; 8016 ushort q_addr; 8017 uchar next_qp; 8018 8019 iop_base = asc_dvc->iop_base; 8020 sg_head = scsiq->sg_head; 8021 saved_data_addr = scsiq->q1.data_addr; 8022 saved_data_cnt = scsiq->q1.data_cnt; 8023 scsiq->q1.data_addr = cpu_to_le32(sg_head->sg_list[0].addr); 8024 scsiq->q1.data_cnt = cpu_to_le32(sg_head->sg_list[0].bytes); 8025 /* 8026 * Set sg_entry_cnt to be the number of SG elements that 8027 * will fit in the allocated SG queues. It is minus 1, because 8028 * the first SG element is handled above. 8029 */ 8030 sg_entry_cnt = sg_head->entry_cnt - 1; 8031 8032 if (sg_entry_cnt != 0) { 8033 scsiq->q1.cntl |= QC_SG_HEAD; 8034 q_addr = ASC_QNO_TO_QADDR(q_no); 8035 sg_index = 1; 8036 scsiq->q1.sg_queue_cnt = sg_head->queue_cnt; 8037 scsi_sg_q.sg_head_qp = q_no; 8038 scsi_sg_q.cntl = QCSG_SG_XFER_LIST; 8039 for (i = 0; i < sg_head->queue_cnt; i++) { 8040 scsi_sg_q.seq_no = i + 1; 8041 if (sg_entry_cnt > ASC_SG_LIST_PER_Q) { 8042 sg_list_dwords = (uchar)(ASC_SG_LIST_PER_Q * 2); 8043 sg_entry_cnt -= ASC_SG_LIST_PER_Q; 8044 if (i == 0) { 8045 scsi_sg_q.sg_list_cnt = 8046 ASC_SG_LIST_PER_Q; 8047 scsi_sg_q.sg_cur_list_cnt = 8048 ASC_SG_LIST_PER_Q; 8049 } else { 8050 scsi_sg_q.sg_list_cnt = 8051 ASC_SG_LIST_PER_Q - 1; 8052 scsi_sg_q.sg_cur_list_cnt = 8053 ASC_SG_LIST_PER_Q - 1; 8054 } 8055 } else { 8056 scsi_sg_q.cntl |= QCSG_SG_XFER_END; 8057 sg_list_dwords = sg_entry_cnt << 1; 8058 if (i == 0) { 8059 scsi_sg_q.sg_list_cnt = sg_entry_cnt; 8060 scsi_sg_q.sg_cur_list_cnt = 8061 sg_entry_cnt; 8062 } else { 8063 scsi_sg_q.sg_list_cnt = 8064 sg_entry_cnt - 1; 8065 scsi_sg_q.sg_cur_list_cnt = 8066 sg_entry_cnt - 1; 8067 } 8068 sg_entry_cnt = 0; 8069 } 8070 next_qp = AscReadLramByte(iop_base, 8071 (ushort)(q_addr + 8072 ASC_SCSIQ_B_FWD)); 8073 scsi_sg_q.q_no = next_qp; 8074 q_addr = ASC_QNO_TO_QADDR(next_qp); 8075 AscMemWordCopyPtrToLram(iop_base, 8076 q_addr + ASC_SCSIQ_SGHD_CPY_BEG, 8077 (uchar *)&scsi_sg_q, 8078 sizeof(ASC_SG_LIST_Q) >> 1); 8079 AscMemDWordCopyPtrToLram(iop_base, 8080 q_addr + ASC_SGQ_LIST_BEG, 8081 (uchar *)&sg_head-> 8082 sg_list[sg_index], 8083 sg_list_dwords); 8084 sg_index += ASC_SG_LIST_PER_Q; 8085 scsiq->next_sg_index = sg_index; 8086 } 8087 } else { 8088 scsiq->q1.cntl &= ~QC_SG_HEAD; 8089 } 8090 sta = AscPutReadyQueue(asc_dvc, scsiq, q_no); 8091 scsiq->q1.data_addr = saved_data_addr; 8092 scsiq->q1.data_cnt = saved_data_cnt; 8093 return (sta); 8094 } 8095 8096 static int 8097 AscSendScsiQueue(ASC_DVC_VAR *asc_dvc, ASC_SCSI_Q *scsiq, uchar n_q_required) 8098 { 8099 PortAddr iop_base; 8100 uchar free_q_head; 8101 uchar next_qp; 8102 uchar tid_no; 8103 uchar target_ix; 8104 int sta; 8105 8106 iop_base = asc_dvc->iop_base; 8107 target_ix = scsiq->q2.target_ix; 8108 tid_no = ASC_TIX_TO_TID(target_ix); 8109 sta = 0; 8110 free_q_head = (uchar)AscGetVarFreeQHead(iop_base); 8111 if (n_q_required > 1) { 8112 next_qp = AscAllocMultipleFreeQueue(iop_base, free_q_head, 8113 (uchar)n_q_required); 8114 if (next_qp != ASC_QLINK_END) { 8115 asc_dvc->last_q_shortage = 0; 8116 scsiq->sg_head->queue_cnt = n_q_required - 1; 8117 scsiq->q1.q_no = free_q_head; 8118 sta = AscPutReadySgListQueue(asc_dvc, scsiq, 8119 free_q_head); 8120 } 8121 } else if (n_q_required == 1) { 8122 next_qp = AscAllocFreeQueue(iop_base, free_q_head); 8123 if (next_qp != ASC_QLINK_END) { 8124 scsiq->q1.q_no = free_q_head; 8125 sta = AscPutReadyQueue(asc_dvc, scsiq, free_q_head); 8126 } 8127 } 8128 if (sta == 1) { 8129 AscPutVarFreeQHead(iop_base, next_qp); 8130 asc_dvc->cur_total_qng += n_q_required; 8131 asc_dvc->cur_dvc_qng[tid_no]++; 8132 } 8133 return sta; 8134 } 8135 8136 #define ASC_SYN_OFFSET_ONE_DISABLE_LIST 16 8137 static uchar _syn_offset_one_disable_cmd[ASC_SYN_OFFSET_ONE_DISABLE_LIST] = { 8138 INQUIRY, 8139 REQUEST_SENSE, 8140 READ_CAPACITY, 8141 READ_TOC, 8142 MODE_SELECT, 8143 MODE_SENSE, 8144 MODE_SELECT_10, 8145 MODE_SENSE_10, 8146 0xFF, 8147 0xFF, 8148 0xFF, 8149 0xFF, 8150 0xFF, 8151 0xFF, 8152 0xFF, 8153 0xFF 8154 }; 8155 8156 static int AscExeScsiQueue(ASC_DVC_VAR *asc_dvc, ASC_SCSI_Q *scsiq) 8157 { 8158 PortAddr iop_base; 8159 int sta; 8160 int n_q_required; 8161 bool disable_syn_offset_one_fix; 8162 int i; 8163 u32 addr; 8164 ushort sg_entry_cnt = 0; 8165 ushort sg_entry_cnt_minus_one = 0; 8166 uchar target_ix; 8167 uchar tid_no; 8168 uchar sdtr_data; 8169 uchar extra_bytes; 8170 uchar scsi_cmd; 8171 uchar disable_cmd; 8172 ASC_SG_HEAD *sg_head; 8173 unsigned long data_cnt; 8174 8175 iop_base = asc_dvc->iop_base; 8176 sg_head = scsiq->sg_head; 8177 if (asc_dvc->err_code != 0) 8178 return ASC_ERROR; 8179 scsiq->q1.q_no = 0; 8180 if ((scsiq->q2.tag_code & ASC_TAG_FLAG_EXTRA_BYTES) == 0) { 8181 scsiq->q1.extra_bytes = 0; 8182 } 8183 sta = 0; 8184 target_ix = scsiq->q2.target_ix; 8185 tid_no = ASC_TIX_TO_TID(target_ix); 8186 n_q_required = 1; 8187 if (scsiq->cdbptr[0] == REQUEST_SENSE) { 8188 if ((asc_dvc->init_sdtr & scsiq->q1.target_id) != 0) { 8189 asc_dvc->sdtr_done &= ~scsiq->q1.target_id; 8190 sdtr_data = AscGetMCodeInitSDTRAtID(iop_base, tid_no); 8191 AscMsgOutSDTR(asc_dvc, 8192 asc_dvc-> 8193 sdtr_period_tbl[(sdtr_data >> 4) & 8194 (uchar)(asc_dvc-> 8195 max_sdtr_index - 8196 1)], 8197 (uchar)(sdtr_data & (uchar) 8198 ASC_SYN_MAX_OFFSET)); 8199 scsiq->q1.cntl |= (QC_MSG_OUT | QC_URGENT); 8200 } 8201 } 8202 if (asc_dvc->in_critical_cnt != 0) { 8203 AscSetLibErrorCode(asc_dvc, ASCQ_ERR_CRITICAL_RE_ENTRY); 8204 return ASC_ERROR; 8205 } 8206 asc_dvc->in_critical_cnt++; 8207 if ((scsiq->q1.cntl & QC_SG_HEAD) != 0) { 8208 if ((sg_entry_cnt = sg_head->entry_cnt) == 0) { 8209 asc_dvc->in_critical_cnt--; 8210 return ASC_ERROR; 8211 } 8212 if (sg_entry_cnt > ASC_MAX_SG_LIST) { 8213 asc_dvc->in_critical_cnt--; 8214 return ASC_ERROR; 8215 } 8216 if (sg_entry_cnt == 1) { 8217 scsiq->q1.data_addr = cpu_to_le32(sg_head->sg_list[0].addr); 8218 scsiq->q1.data_cnt = cpu_to_le32(sg_head->sg_list[0].bytes); 8219 scsiq->q1.cntl &= ~(QC_SG_HEAD | QC_SG_SWAP_QUEUE); 8220 } 8221 sg_entry_cnt_minus_one = sg_entry_cnt - 1; 8222 } 8223 scsi_cmd = scsiq->cdbptr[0]; 8224 disable_syn_offset_one_fix = false; 8225 if ((asc_dvc->pci_fix_asyn_xfer & scsiq->q1.target_id) && 8226 !(asc_dvc->pci_fix_asyn_xfer_always & scsiq->q1.target_id)) { 8227 if (scsiq->q1.cntl & QC_SG_HEAD) { 8228 data_cnt = 0; 8229 for (i = 0; i < sg_entry_cnt; i++) { 8230 data_cnt += le32_to_cpu(sg_head->sg_list[i]. 8231 bytes); 8232 } 8233 } else { 8234 data_cnt = le32_to_cpu(scsiq->q1.data_cnt); 8235 } 8236 if (data_cnt != 0UL) { 8237 if (data_cnt < 512UL) { 8238 disable_syn_offset_one_fix = true; 8239 } else { 8240 for (i = 0; i < ASC_SYN_OFFSET_ONE_DISABLE_LIST; 8241 i++) { 8242 disable_cmd = 8243 _syn_offset_one_disable_cmd[i]; 8244 if (disable_cmd == 0xFF) { 8245 break; 8246 } 8247 if (scsi_cmd == disable_cmd) { 8248 disable_syn_offset_one_fix = 8249 true; 8250 break; 8251 } 8252 } 8253 } 8254 } 8255 } 8256 if (disable_syn_offset_one_fix) { 8257 scsiq->q2.tag_code &= ~SIMPLE_QUEUE_TAG; 8258 scsiq->q2.tag_code |= (ASC_TAG_FLAG_DISABLE_ASYN_USE_SYN_FIX | 8259 ASC_TAG_FLAG_DISABLE_DISCONNECT); 8260 } else { 8261 scsiq->q2.tag_code &= 0x27; 8262 } 8263 if ((scsiq->q1.cntl & QC_SG_HEAD) != 0) { 8264 if (asc_dvc->bug_fix_cntl) { 8265 if (asc_dvc->bug_fix_cntl & ASC_BUG_FIX_IF_NOT_DWB) { 8266 if ((scsi_cmd == READ_6) || 8267 (scsi_cmd == READ_10)) { 8268 addr = le32_to_cpu(sg_head-> 8269 sg_list 8270 [sg_entry_cnt_minus_one]. 8271 addr) + 8272 le32_to_cpu(sg_head-> 8273 sg_list 8274 [sg_entry_cnt_minus_one]. 8275 bytes); 8276 extra_bytes = 8277 (uchar)((ushort)addr & 0x0003); 8278 if ((extra_bytes != 0) 8279 && 8280 ((scsiq->q2. 8281 tag_code & 8282 ASC_TAG_FLAG_EXTRA_BYTES) 8283 == 0)) { 8284 scsiq->q2.tag_code |= 8285 ASC_TAG_FLAG_EXTRA_BYTES; 8286 scsiq->q1.extra_bytes = 8287 extra_bytes; 8288 data_cnt = 8289 le32_to_cpu(sg_head-> 8290 sg_list 8291 [sg_entry_cnt_minus_one]. 8292 bytes); 8293 data_cnt -= extra_bytes; 8294 sg_head-> 8295 sg_list 8296 [sg_entry_cnt_minus_one]. 8297 bytes = 8298 cpu_to_le32(data_cnt); 8299 } 8300 } 8301 } 8302 } 8303 sg_head->entry_to_copy = sg_head->entry_cnt; 8304 n_q_required = AscSgListToQueue(sg_entry_cnt); 8305 if ((AscGetNumOfFreeQueue(asc_dvc, target_ix, n_q_required) >= 8306 (uint) n_q_required) 8307 || ((scsiq->q1.cntl & QC_URGENT) != 0)) { 8308 if ((sta = 8309 AscSendScsiQueue(asc_dvc, scsiq, 8310 n_q_required)) == 1) { 8311 asc_dvc->in_critical_cnt--; 8312 return (sta); 8313 } 8314 } 8315 } else { 8316 if (asc_dvc->bug_fix_cntl) { 8317 if (asc_dvc->bug_fix_cntl & ASC_BUG_FIX_IF_NOT_DWB) { 8318 if ((scsi_cmd == READ_6) || 8319 (scsi_cmd == READ_10)) { 8320 addr = 8321 le32_to_cpu(scsiq->q1.data_addr) + 8322 le32_to_cpu(scsiq->q1.data_cnt); 8323 extra_bytes = 8324 (uchar)((ushort)addr & 0x0003); 8325 if ((extra_bytes != 0) 8326 && 8327 ((scsiq->q2. 8328 tag_code & 8329 ASC_TAG_FLAG_EXTRA_BYTES) 8330 == 0)) { 8331 data_cnt = 8332 le32_to_cpu(scsiq->q1. 8333 data_cnt); 8334 if (((ushort)data_cnt & 0x01FF) 8335 == 0) { 8336 scsiq->q2.tag_code |= 8337 ASC_TAG_FLAG_EXTRA_BYTES; 8338 data_cnt -= extra_bytes; 8339 scsiq->q1.data_cnt = 8340 cpu_to_le32 8341 (data_cnt); 8342 scsiq->q1.extra_bytes = 8343 extra_bytes; 8344 } 8345 } 8346 } 8347 } 8348 } 8349 n_q_required = 1; 8350 if ((AscGetNumOfFreeQueue(asc_dvc, target_ix, 1) >= 1) || 8351 ((scsiq->q1.cntl & QC_URGENT) != 0)) { 8352 if ((sta = AscSendScsiQueue(asc_dvc, scsiq, 8353 n_q_required)) == 1) { 8354 asc_dvc->in_critical_cnt--; 8355 return (sta); 8356 } 8357 } 8358 } 8359 asc_dvc->in_critical_cnt--; 8360 return (sta); 8361 } 8362 8363 /* 8364 * AdvExeScsiQueue() - Send a request to the RISC microcode program. 8365 * 8366 * Allocate a carrier structure, point the carrier to the ADV_SCSI_REQ_Q, 8367 * add the carrier to the ICQ (Initiator Command Queue), and tickle the 8368 * RISC to notify it a new command is ready to be executed. 8369 * 8370 * If 'done_status' is not set to QD_DO_RETRY, then 'error_retry' will be 8371 * set to SCSI_MAX_RETRY. 8372 * 8373 * Multi-byte fields in the ADV_SCSI_REQ_Q that are used by the microcode 8374 * for DMA addresses or math operations are byte swapped to little-endian 8375 * order. 8376 * 8377 * Return: 8378 * ADV_SUCCESS(1) - The request was successfully queued. 8379 * ADV_BUSY(0) - Resource unavailable; Retry again after pending 8380 * request completes. 8381 * ADV_ERROR(-1) - Invalid ADV_SCSI_REQ_Q request structure 8382 * host IC error. 8383 */ 8384 static int AdvExeScsiQueue(ADV_DVC_VAR *asc_dvc, adv_req_t *reqp) 8385 { 8386 AdvPortAddr iop_base; 8387 ADV_CARR_T *new_carrp; 8388 ADV_SCSI_REQ_Q *scsiq = &reqp->scsi_req_q; 8389 8390 /* 8391 * The ADV_SCSI_REQ_Q 'target_id' field should never exceed ADV_MAX_TID. 8392 */ 8393 if (scsiq->target_id > ADV_MAX_TID) { 8394 scsiq->host_status = QHSTA_M_INVALID_DEVICE; 8395 scsiq->done_status = QD_WITH_ERROR; 8396 return ADV_ERROR; 8397 } 8398 8399 iop_base = asc_dvc->iop_base; 8400 8401 /* 8402 * Allocate a carrier ensuring at least one carrier always 8403 * remains on the freelist and initialize fields. 8404 */ 8405 new_carrp = adv_get_next_carrier(asc_dvc); 8406 if (!new_carrp) { 8407 ASC_DBG(1, "No free carriers\n"); 8408 return ADV_BUSY; 8409 } 8410 8411 asc_dvc->carr_pending_cnt++; 8412 8413 /* Save virtual and physical address of ADV_SCSI_REQ_Q and carrier. */ 8414 scsiq->scsiq_ptr = cpu_to_le32(scsiq->srb_tag); 8415 scsiq->scsiq_rptr = cpu_to_le32(reqp->req_addr); 8416 8417 scsiq->carr_va = asc_dvc->icq_sp->carr_va; 8418 scsiq->carr_pa = asc_dvc->icq_sp->carr_pa; 8419 8420 /* 8421 * Use the current stopper to send the ADV_SCSI_REQ_Q command to 8422 * the microcode. The newly allocated stopper will become the new 8423 * stopper. 8424 */ 8425 asc_dvc->icq_sp->areq_vpa = scsiq->scsiq_rptr; 8426 8427 /* 8428 * Set the 'next_vpa' pointer for the old stopper to be the 8429 * physical address of the new stopper. The RISC can only 8430 * follow physical addresses. 8431 */ 8432 asc_dvc->icq_sp->next_vpa = new_carrp->carr_pa; 8433 8434 /* 8435 * Set the host adapter stopper pointer to point to the new carrier. 8436 */ 8437 asc_dvc->icq_sp = new_carrp; 8438 8439 if (asc_dvc->chip_type == ADV_CHIP_ASC3550 || 8440 asc_dvc->chip_type == ADV_CHIP_ASC38C0800) { 8441 /* 8442 * Tickle the RISC to tell it to read its Command Queue Head pointer. 8443 */ 8444 AdvWriteByteRegister(iop_base, IOPB_TICKLE, ADV_TICKLE_A); 8445 if (asc_dvc->chip_type == ADV_CHIP_ASC3550) { 8446 /* 8447 * Clear the tickle value. In the ASC-3550 the RISC flag 8448 * command 'clr_tickle_a' does not work unless the host 8449 * value is cleared. 8450 */ 8451 AdvWriteByteRegister(iop_base, IOPB_TICKLE, 8452 ADV_TICKLE_NOP); 8453 } 8454 } else if (asc_dvc->chip_type == ADV_CHIP_ASC38C1600) { 8455 /* 8456 * Notify the RISC a carrier is ready by writing the physical 8457 * address of the new carrier stopper to the COMMA register. 8458 */ 8459 AdvWriteDWordRegister(iop_base, IOPDW_COMMA, 8460 le32_to_cpu(new_carrp->carr_pa)); 8461 } 8462 8463 return ADV_SUCCESS; 8464 } 8465 8466 /* 8467 * Execute a single 'struct scsi_cmnd'. 8468 */ 8469 static int asc_execute_scsi_cmnd(struct scsi_cmnd *scp) 8470 { 8471 int ret, err_code; 8472 struct asc_board *boardp = shost_priv(scp->device->host); 8473 8474 ASC_DBG(1, "scp 0x%p\n", scp); 8475 8476 if (ASC_NARROW_BOARD(boardp)) { 8477 ASC_DVC_VAR *asc_dvc = &boardp->dvc_var.asc_dvc_var; 8478 struct asc_scsi_q asc_scsi_q; 8479 8480 ret = asc_build_req(boardp, scp, &asc_scsi_q); 8481 if (ret != ASC_NOERROR) { 8482 ASC_STATS(scp->device->host, build_error); 8483 return ret; 8484 } 8485 8486 ret = AscExeScsiQueue(asc_dvc, &asc_scsi_q); 8487 kfree(asc_scsi_q.sg_head); 8488 err_code = asc_dvc->err_code; 8489 } else { 8490 ADV_DVC_VAR *adv_dvc = &boardp->dvc_var.adv_dvc_var; 8491 adv_req_t *adv_reqp; 8492 8493 switch (adv_build_req(boardp, scp, &adv_reqp)) { 8494 case ASC_NOERROR: 8495 ASC_DBG(3, "adv_build_req ASC_NOERROR\n"); 8496 break; 8497 case ASC_BUSY: 8498 ASC_DBG(1, "adv_build_req ASC_BUSY\n"); 8499 /* 8500 * The asc_stats fields 'adv_build_noreq' and 8501 * 'adv_build_nosg' count wide board busy conditions. 8502 * They are updated in adv_build_req and 8503 * adv_get_sglist, respectively. 8504 */ 8505 return ASC_BUSY; 8506 case ASC_ERROR: 8507 default: 8508 ASC_DBG(1, "adv_build_req ASC_ERROR\n"); 8509 ASC_STATS(scp->device->host, build_error); 8510 return ASC_ERROR; 8511 } 8512 8513 ret = AdvExeScsiQueue(adv_dvc, adv_reqp); 8514 err_code = adv_dvc->err_code; 8515 } 8516 8517 switch (ret) { 8518 case ASC_NOERROR: 8519 ASC_STATS(scp->device->host, exe_noerror); 8520 /* 8521 * Increment monotonically increasing per device 8522 * successful request counter. Wrapping doesn't matter. 8523 */ 8524 boardp->reqcnt[scp->device->id]++; 8525 ASC_DBG(1, "ExeScsiQueue() ASC_NOERROR\n"); 8526 break; 8527 case ASC_BUSY: 8528 ASC_DBG(1, "ExeScsiQueue() ASC_BUSY\n"); 8529 ASC_STATS(scp->device->host, exe_busy); 8530 break; 8531 case ASC_ERROR: 8532 scmd_printk(KERN_ERR, scp, "ExeScsiQueue() ASC_ERROR, " 8533 "err_code 0x%x\n", err_code); 8534 ASC_STATS(scp->device->host, exe_error); 8535 scp->result = HOST_BYTE(DID_ERROR); 8536 break; 8537 default: 8538 scmd_printk(KERN_ERR, scp, "ExeScsiQueue() unknown, " 8539 "err_code 0x%x\n", err_code); 8540 ASC_STATS(scp->device->host, exe_unknown); 8541 scp->result = HOST_BYTE(DID_ERROR); 8542 break; 8543 } 8544 8545 ASC_DBG(1, "end\n"); 8546 return ret; 8547 } 8548 8549 /* 8550 * advansys_queuecommand() - interrupt-driven I/O entrypoint. 8551 * 8552 * This function always returns 0. Command return status is saved 8553 * in the 'scp' result field. 8554 */ 8555 static int 8556 advansys_queuecommand_lck(struct scsi_cmnd *scp, void (*done)(struct scsi_cmnd *)) 8557 { 8558 struct Scsi_Host *shost = scp->device->host; 8559 int asc_res, result = 0; 8560 8561 ASC_STATS(shost, queuecommand); 8562 scp->scsi_done = done; 8563 8564 asc_res = asc_execute_scsi_cmnd(scp); 8565 8566 switch (asc_res) { 8567 case ASC_NOERROR: 8568 break; 8569 case ASC_BUSY: 8570 result = SCSI_MLQUEUE_HOST_BUSY; 8571 break; 8572 case ASC_ERROR: 8573 default: 8574 asc_scsi_done(scp); 8575 break; 8576 } 8577 8578 return result; 8579 } 8580 8581 static DEF_SCSI_QCMD(advansys_queuecommand) 8582 8583 static ushort AscGetEisaChipCfg(PortAddr iop_base) 8584 { 8585 PortAddr eisa_cfg_iop = (PortAddr) ASC_GET_EISA_SLOT(iop_base) | 8586 (PortAddr) (ASC_EISA_CFG_IOP_MASK); 8587 return inpw(eisa_cfg_iop); 8588 } 8589 8590 /* 8591 * Return the BIOS address of the adapter at the specified 8592 * I/O port and with the specified bus type. 8593 */ 8594 static unsigned short AscGetChipBiosAddress(PortAddr iop_base, 8595 unsigned short bus_type) 8596 { 8597 unsigned short cfg_lsw; 8598 unsigned short bios_addr; 8599 8600 /* 8601 * The PCI BIOS is re-located by the motherboard BIOS. Because 8602 * of this the driver can not determine where a PCI BIOS is 8603 * loaded and executes. 8604 */ 8605 if (bus_type & ASC_IS_PCI) 8606 return 0; 8607 8608 if ((bus_type & ASC_IS_EISA) != 0) { 8609 cfg_lsw = AscGetEisaChipCfg(iop_base); 8610 cfg_lsw &= 0x000F; 8611 bios_addr = ASC_BIOS_MIN_ADDR + cfg_lsw * ASC_BIOS_BANK_SIZE; 8612 return bios_addr; 8613 } 8614 8615 cfg_lsw = AscGetChipCfgLsw(iop_base); 8616 8617 /* 8618 * ISA PnP uses the top bit as the 32K BIOS flag 8619 */ 8620 if (bus_type == ASC_IS_ISAPNP) 8621 cfg_lsw &= 0x7FFF; 8622 bios_addr = ASC_BIOS_MIN_ADDR + (cfg_lsw >> 12) * ASC_BIOS_BANK_SIZE; 8623 return bios_addr; 8624 } 8625 8626 static uchar AscSetChipScsiID(PortAddr iop_base, uchar new_host_id) 8627 { 8628 ushort cfg_lsw; 8629 8630 if (AscGetChipScsiID(iop_base) == new_host_id) { 8631 return (new_host_id); 8632 } 8633 cfg_lsw = AscGetChipCfgLsw(iop_base); 8634 cfg_lsw &= 0xF8FF; 8635 cfg_lsw |= (ushort)((new_host_id & ASC_MAX_TID) << 8); 8636 AscSetChipCfgLsw(iop_base, cfg_lsw); 8637 return (AscGetChipScsiID(iop_base)); 8638 } 8639 8640 static unsigned char AscGetChipScsiCtrl(PortAddr iop_base) 8641 { 8642 unsigned char sc; 8643 8644 AscSetBank(iop_base, 1); 8645 sc = inp(iop_base + IOP_REG_SC); 8646 AscSetBank(iop_base, 0); 8647 return sc; 8648 } 8649 8650 static unsigned char AscGetChipVersion(PortAddr iop_base, 8651 unsigned short bus_type) 8652 { 8653 if (bus_type & ASC_IS_EISA) { 8654 PortAddr eisa_iop; 8655 unsigned char revision; 8656 eisa_iop = (PortAddr) ASC_GET_EISA_SLOT(iop_base) | 8657 (PortAddr) ASC_EISA_REV_IOP_MASK; 8658 revision = inp(eisa_iop); 8659 return ASC_CHIP_MIN_VER_EISA - 1 + revision; 8660 } 8661 return AscGetChipVerNo(iop_base); 8662 } 8663 8664 #ifdef CONFIG_ISA 8665 static void AscEnableIsaDma(uchar dma_channel) 8666 { 8667 if (dma_channel < 4) { 8668 outp(0x000B, (ushort)(0xC0 | dma_channel)); 8669 outp(0x000A, dma_channel); 8670 } else if (dma_channel < 8) { 8671 outp(0x00D6, (ushort)(0xC0 | (dma_channel - 4))); 8672 outp(0x00D4, (ushort)(dma_channel - 4)); 8673 } 8674 } 8675 #endif /* CONFIG_ISA */ 8676 8677 static int AscStopQueueExe(PortAddr iop_base) 8678 { 8679 int count = 0; 8680 8681 if (AscReadLramByte(iop_base, ASCV_STOP_CODE_B) == 0) { 8682 AscWriteLramByte(iop_base, ASCV_STOP_CODE_B, 8683 ASC_STOP_REQ_RISC_STOP); 8684 do { 8685 if (AscReadLramByte(iop_base, ASCV_STOP_CODE_B) & 8686 ASC_STOP_ACK_RISC_STOP) { 8687 return (1); 8688 } 8689 mdelay(100); 8690 } while (count++ < 20); 8691 } 8692 return (0); 8693 } 8694 8695 static unsigned int AscGetMaxDmaCount(ushort bus_type) 8696 { 8697 if (bus_type & ASC_IS_ISA) 8698 return ASC_MAX_ISA_DMA_COUNT; 8699 else if (bus_type & (ASC_IS_EISA | ASC_IS_VL)) 8700 return ASC_MAX_VL_DMA_COUNT; 8701 return ASC_MAX_PCI_DMA_COUNT; 8702 } 8703 8704 #ifdef CONFIG_ISA 8705 static ushort AscGetIsaDmaChannel(PortAddr iop_base) 8706 { 8707 ushort channel; 8708 8709 channel = AscGetChipCfgLsw(iop_base) & 0x0003; 8710 if (channel == 0x03) 8711 return (0); 8712 else if (channel == 0x00) 8713 return (7); 8714 return (channel + 4); 8715 } 8716 8717 static ushort AscSetIsaDmaChannel(PortAddr iop_base, ushort dma_channel) 8718 { 8719 ushort cfg_lsw; 8720 uchar value; 8721 8722 if ((dma_channel >= 5) && (dma_channel <= 7)) { 8723 if (dma_channel == 7) 8724 value = 0x00; 8725 else 8726 value = dma_channel - 4; 8727 cfg_lsw = AscGetChipCfgLsw(iop_base) & 0xFFFC; 8728 cfg_lsw |= value; 8729 AscSetChipCfgLsw(iop_base, cfg_lsw); 8730 return (AscGetIsaDmaChannel(iop_base)); 8731 } 8732 return 0; 8733 } 8734 8735 static uchar AscGetIsaDmaSpeed(PortAddr iop_base) 8736 { 8737 uchar speed_value; 8738 8739 AscSetBank(iop_base, 1); 8740 speed_value = AscReadChipDmaSpeed(iop_base); 8741 speed_value &= 0x07; 8742 AscSetBank(iop_base, 0); 8743 return speed_value; 8744 } 8745 8746 static uchar AscSetIsaDmaSpeed(PortAddr iop_base, uchar speed_value) 8747 { 8748 speed_value &= 0x07; 8749 AscSetBank(iop_base, 1); 8750 AscWriteChipDmaSpeed(iop_base, speed_value); 8751 AscSetBank(iop_base, 0); 8752 return AscGetIsaDmaSpeed(iop_base); 8753 } 8754 #endif /* CONFIG_ISA */ 8755 8756 static void AscInitAscDvcVar(ASC_DVC_VAR *asc_dvc) 8757 { 8758 int i; 8759 PortAddr iop_base; 8760 uchar chip_version; 8761 8762 iop_base = asc_dvc->iop_base; 8763 asc_dvc->err_code = 0; 8764 if ((asc_dvc->bus_type & 8765 (ASC_IS_ISA | ASC_IS_PCI | ASC_IS_EISA | ASC_IS_VL)) == 0) { 8766 asc_dvc->err_code |= ASC_IERR_NO_BUS_TYPE; 8767 } 8768 AscSetChipControl(iop_base, CC_HALT); 8769 AscSetChipStatus(iop_base, 0); 8770 asc_dvc->bug_fix_cntl = 0; 8771 asc_dvc->pci_fix_asyn_xfer = 0; 8772 asc_dvc->pci_fix_asyn_xfer_always = 0; 8773 /* asc_dvc->init_state initialized in AscInitGetConfig(). */ 8774 asc_dvc->sdtr_done = 0; 8775 asc_dvc->cur_total_qng = 0; 8776 asc_dvc->is_in_int = false; 8777 asc_dvc->in_critical_cnt = 0; 8778 asc_dvc->last_q_shortage = 0; 8779 asc_dvc->use_tagged_qng = 0; 8780 asc_dvc->no_scam = 0; 8781 asc_dvc->unit_not_ready = 0; 8782 asc_dvc->queue_full_or_busy = 0; 8783 asc_dvc->redo_scam = 0; 8784 asc_dvc->res2 = 0; 8785 asc_dvc->min_sdtr_index = 0; 8786 asc_dvc->cfg->can_tagged_qng = 0; 8787 asc_dvc->cfg->cmd_qng_enabled = 0; 8788 asc_dvc->dvc_cntl = ASC_DEF_DVC_CNTL; 8789 asc_dvc->init_sdtr = 0; 8790 asc_dvc->max_total_qng = ASC_DEF_MAX_TOTAL_QNG; 8791 asc_dvc->scsi_reset_wait = 3; 8792 asc_dvc->start_motor = ASC_SCSI_WIDTH_BIT_SET; 8793 asc_dvc->max_dma_count = AscGetMaxDmaCount(asc_dvc->bus_type); 8794 asc_dvc->cfg->sdtr_enable = ASC_SCSI_WIDTH_BIT_SET; 8795 asc_dvc->cfg->disc_enable = ASC_SCSI_WIDTH_BIT_SET; 8796 asc_dvc->cfg->chip_scsi_id = ASC_DEF_CHIP_SCSI_ID; 8797 chip_version = AscGetChipVersion(iop_base, asc_dvc->bus_type); 8798 asc_dvc->cfg->chip_version = chip_version; 8799 asc_dvc->sdtr_period_tbl = asc_syn_xfer_period; 8800 asc_dvc->max_sdtr_index = 7; 8801 if ((asc_dvc->bus_type & ASC_IS_PCI) && 8802 (chip_version >= ASC_CHIP_VER_PCI_ULTRA_3150)) { 8803 asc_dvc->bus_type = ASC_IS_PCI_ULTRA; 8804 asc_dvc->sdtr_period_tbl = asc_syn_ultra_xfer_period; 8805 asc_dvc->max_sdtr_index = 15; 8806 if (chip_version == ASC_CHIP_VER_PCI_ULTRA_3150) { 8807 AscSetExtraControl(iop_base, 8808 (SEC_ACTIVE_NEGATE | SEC_SLEW_RATE)); 8809 } else if (chip_version >= ASC_CHIP_VER_PCI_ULTRA_3050) { 8810 AscSetExtraControl(iop_base, 8811 (SEC_ACTIVE_NEGATE | 8812 SEC_ENABLE_FILTER)); 8813 } 8814 } 8815 if (asc_dvc->bus_type == ASC_IS_PCI) { 8816 AscSetExtraControl(iop_base, 8817 (SEC_ACTIVE_NEGATE | SEC_SLEW_RATE)); 8818 } 8819 8820 asc_dvc->cfg->isa_dma_speed = ASC_DEF_ISA_DMA_SPEED; 8821 #ifdef CONFIG_ISA 8822 if ((asc_dvc->bus_type & ASC_IS_ISA) != 0) { 8823 if (chip_version >= ASC_CHIP_MIN_VER_ISA_PNP) { 8824 AscSetChipIFC(iop_base, IFC_INIT_DEFAULT); 8825 asc_dvc->bus_type = ASC_IS_ISAPNP; 8826 } 8827 asc_dvc->cfg->isa_dma_channel = 8828 (uchar)AscGetIsaDmaChannel(iop_base); 8829 } 8830 #endif /* CONFIG_ISA */ 8831 for (i = 0; i <= ASC_MAX_TID; i++) { 8832 asc_dvc->cur_dvc_qng[i] = 0; 8833 asc_dvc->max_dvc_qng[i] = ASC_MAX_SCSI1_QNG; 8834 asc_dvc->scsiq_busy_head[i] = (ASC_SCSI_Q *)0L; 8835 asc_dvc->scsiq_busy_tail[i] = (ASC_SCSI_Q *)0L; 8836 asc_dvc->cfg->max_tag_qng[i] = ASC_MAX_INRAM_TAG_QNG; 8837 } 8838 } 8839 8840 static int AscWriteEEPCmdReg(PortAddr iop_base, uchar cmd_reg) 8841 { 8842 int retry; 8843 8844 for (retry = 0; retry < ASC_EEP_MAX_RETRY; retry++) { 8845 unsigned char read_back; 8846 AscSetChipEEPCmd(iop_base, cmd_reg); 8847 mdelay(1); 8848 read_back = AscGetChipEEPCmd(iop_base); 8849 if (read_back == cmd_reg) 8850 return 1; 8851 } 8852 return 0; 8853 } 8854 8855 static void AscWaitEEPRead(void) 8856 { 8857 mdelay(1); 8858 } 8859 8860 static ushort AscReadEEPWord(PortAddr iop_base, uchar addr) 8861 { 8862 ushort read_wval; 8863 uchar cmd_reg; 8864 8865 AscWriteEEPCmdReg(iop_base, ASC_EEP_CMD_WRITE_DISABLE); 8866 AscWaitEEPRead(); 8867 cmd_reg = addr | ASC_EEP_CMD_READ; 8868 AscWriteEEPCmdReg(iop_base, cmd_reg); 8869 AscWaitEEPRead(); 8870 read_wval = AscGetChipEEPData(iop_base); 8871 AscWaitEEPRead(); 8872 return read_wval; 8873 } 8874 8875 static ushort AscGetEEPConfig(PortAddr iop_base, ASCEEP_CONFIG *cfg_buf, 8876 ushort bus_type) 8877 { 8878 ushort wval; 8879 ushort sum; 8880 ushort *wbuf; 8881 int cfg_beg; 8882 int cfg_end; 8883 int uchar_end_in_config = ASC_EEP_MAX_DVC_ADDR - 2; 8884 int s_addr; 8885 8886 wbuf = (ushort *)cfg_buf; 8887 sum = 0; 8888 /* Read two config words; Byte-swapping done by AscReadEEPWord(). */ 8889 for (s_addr = 0; s_addr < 2; s_addr++, wbuf++) { 8890 *wbuf = AscReadEEPWord(iop_base, (uchar)s_addr); 8891 sum += *wbuf; 8892 } 8893 if (bus_type & ASC_IS_VL) { 8894 cfg_beg = ASC_EEP_DVC_CFG_BEG_VL; 8895 cfg_end = ASC_EEP_MAX_DVC_ADDR_VL; 8896 } else { 8897 cfg_beg = ASC_EEP_DVC_CFG_BEG; 8898 cfg_end = ASC_EEP_MAX_DVC_ADDR; 8899 } 8900 for (s_addr = cfg_beg; s_addr <= (cfg_end - 1); s_addr++, wbuf++) { 8901 wval = AscReadEEPWord(iop_base, (uchar)s_addr); 8902 if (s_addr <= uchar_end_in_config) { 8903 /* 8904 * Swap all char fields - must unswap bytes already swapped 8905 * by AscReadEEPWord(). 8906 */ 8907 *wbuf = le16_to_cpu(wval); 8908 } else { 8909 /* Don't swap word field at the end - cntl field. */ 8910 *wbuf = wval; 8911 } 8912 sum += wval; /* Checksum treats all EEPROM data as words. */ 8913 } 8914 /* 8915 * Read the checksum word which will be compared against 'sum' 8916 * by the caller. Word field already swapped. 8917 */ 8918 *wbuf = AscReadEEPWord(iop_base, (uchar)s_addr); 8919 return sum; 8920 } 8921 8922 static int AscTestExternalLram(ASC_DVC_VAR *asc_dvc) 8923 { 8924 PortAddr iop_base; 8925 ushort q_addr; 8926 ushort saved_word; 8927 int sta; 8928 8929 iop_base = asc_dvc->iop_base; 8930 sta = 0; 8931 q_addr = ASC_QNO_TO_QADDR(241); 8932 saved_word = AscReadLramWord(iop_base, q_addr); 8933 AscSetChipLramAddr(iop_base, q_addr); 8934 AscSetChipLramData(iop_base, 0x55AA); 8935 mdelay(10); 8936 AscSetChipLramAddr(iop_base, q_addr); 8937 if (AscGetChipLramData(iop_base) == 0x55AA) { 8938 sta = 1; 8939 AscWriteLramWord(iop_base, q_addr, saved_word); 8940 } 8941 return (sta); 8942 } 8943 8944 static void AscWaitEEPWrite(void) 8945 { 8946 mdelay(20); 8947 } 8948 8949 static int AscWriteEEPDataReg(PortAddr iop_base, ushort data_reg) 8950 { 8951 ushort read_back; 8952 int retry; 8953 8954 retry = 0; 8955 while (true) { 8956 AscSetChipEEPData(iop_base, data_reg); 8957 mdelay(1); 8958 read_back = AscGetChipEEPData(iop_base); 8959 if (read_back == data_reg) { 8960 return (1); 8961 } 8962 if (retry++ > ASC_EEP_MAX_RETRY) { 8963 return (0); 8964 } 8965 } 8966 } 8967 8968 static ushort AscWriteEEPWord(PortAddr iop_base, uchar addr, ushort word_val) 8969 { 8970 ushort read_wval; 8971 8972 read_wval = AscReadEEPWord(iop_base, addr); 8973 if (read_wval != word_val) { 8974 AscWriteEEPCmdReg(iop_base, ASC_EEP_CMD_WRITE_ABLE); 8975 AscWaitEEPRead(); 8976 AscWriteEEPDataReg(iop_base, word_val); 8977 AscWaitEEPRead(); 8978 AscWriteEEPCmdReg(iop_base, 8979 (uchar)((uchar)ASC_EEP_CMD_WRITE | addr)); 8980 AscWaitEEPWrite(); 8981 AscWriteEEPCmdReg(iop_base, ASC_EEP_CMD_WRITE_DISABLE); 8982 AscWaitEEPRead(); 8983 return (AscReadEEPWord(iop_base, addr)); 8984 } 8985 return (read_wval); 8986 } 8987 8988 static int AscSetEEPConfigOnce(PortAddr iop_base, ASCEEP_CONFIG *cfg_buf, 8989 ushort bus_type) 8990 { 8991 int n_error; 8992 ushort *wbuf; 8993 ushort word; 8994 ushort sum; 8995 int s_addr; 8996 int cfg_beg; 8997 int cfg_end; 8998 int uchar_end_in_config = ASC_EEP_MAX_DVC_ADDR - 2; 8999 9000 wbuf = (ushort *)cfg_buf; 9001 n_error = 0; 9002 sum = 0; 9003 /* Write two config words; AscWriteEEPWord() will swap bytes. */ 9004 for (s_addr = 0; s_addr < 2; s_addr++, wbuf++) { 9005 sum += *wbuf; 9006 if (*wbuf != AscWriteEEPWord(iop_base, (uchar)s_addr, *wbuf)) { 9007 n_error++; 9008 } 9009 } 9010 if (bus_type & ASC_IS_VL) { 9011 cfg_beg = ASC_EEP_DVC_CFG_BEG_VL; 9012 cfg_end = ASC_EEP_MAX_DVC_ADDR_VL; 9013 } else { 9014 cfg_beg = ASC_EEP_DVC_CFG_BEG; 9015 cfg_end = ASC_EEP_MAX_DVC_ADDR; 9016 } 9017 for (s_addr = cfg_beg; s_addr <= (cfg_end - 1); s_addr++, wbuf++) { 9018 if (s_addr <= uchar_end_in_config) { 9019 /* 9020 * This is a char field. Swap char fields before they are 9021 * swapped again by AscWriteEEPWord(). 9022 */ 9023 word = cpu_to_le16(*wbuf); 9024 if (word != 9025 AscWriteEEPWord(iop_base, (uchar)s_addr, word)) { 9026 n_error++; 9027 } 9028 } else { 9029 /* Don't swap word field at the end - cntl field. */ 9030 if (*wbuf != 9031 AscWriteEEPWord(iop_base, (uchar)s_addr, *wbuf)) { 9032 n_error++; 9033 } 9034 } 9035 sum += *wbuf; /* Checksum calculated from word values. */ 9036 } 9037 /* Write checksum word. It will be swapped by AscWriteEEPWord(). */ 9038 *wbuf = sum; 9039 if (sum != AscWriteEEPWord(iop_base, (uchar)s_addr, sum)) { 9040 n_error++; 9041 } 9042 9043 /* Read EEPROM back again. */ 9044 wbuf = (ushort *)cfg_buf; 9045 /* 9046 * Read two config words; Byte-swapping done by AscReadEEPWord(). 9047 */ 9048 for (s_addr = 0; s_addr < 2; s_addr++, wbuf++) { 9049 if (*wbuf != AscReadEEPWord(iop_base, (uchar)s_addr)) { 9050 n_error++; 9051 } 9052 } 9053 if (bus_type & ASC_IS_VL) { 9054 cfg_beg = ASC_EEP_DVC_CFG_BEG_VL; 9055 cfg_end = ASC_EEP_MAX_DVC_ADDR_VL; 9056 } else { 9057 cfg_beg = ASC_EEP_DVC_CFG_BEG; 9058 cfg_end = ASC_EEP_MAX_DVC_ADDR; 9059 } 9060 for (s_addr = cfg_beg; s_addr <= (cfg_end - 1); s_addr++, wbuf++) { 9061 if (s_addr <= uchar_end_in_config) { 9062 /* 9063 * Swap all char fields. Must unswap bytes already swapped 9064 * by AscReadEEPWord(). 9065 */ 9066 word = 9067 le16_to_cpu(AscReadEEPWord 9068 (iop_base, (uchar)s_addr)); 9069 } else { 9070 /* Don't swap word field at the end - cntl field. */ 9071 word = AscReadEEPWord(iop_base, (uchar)s_addr); 9072 } 9073 if (*wbuf != word) { 9074 n_error++; 9075 } 9076 } 9077 /* Read checksum; Byte swapping not needed. */ 9078 if (AscReadEEPWord(iop_base, (uchar)s_addr) != sum) { 9079 n_error++; 9080 } 9081 return n_error; 9082 } 9083 9084 static int AscSetEEPConfig(PortAddr iop_base, ASCEEP_CONFIG *cfg_buf, 9085 ushort bus_type) 9086 { 9087 int retry; 9088 int n_error; 9089 9090 retry = 0; 9091 while (true) { 9092 if ((n_error = AscSetEEPConfigOnce(iop_base, cfg_buf, 9093 bus_type)) == 0) { 9094 break; 9095 } 9096 if (++retry > ASC_EEP_MAX_RETRY) { 9097 break; 9098 } 9099 } 9100 return n_error; 9101 } 9102 9103 static int AscInitFromEEP(ASC_DVC_VAR *asc_dvc) 9104 { 9105 ASCEEP_CONFIG eep_config_buf; 9106 ASCEEP_CONFIG *eep_config; 9107 PortAddr iop_base; 9108 ushort chksum; 9109 ushort warn_code; 9110 ushort cfg_msw, cfg_lsw; 9111 int i; 9112 int write_eep = 0; 9113 9114 iop_base = asc_dvc->iop_base; 9115 warn_code = 0; 9116 AscWriteLramWord(iop_base, ASCV_HALTCODE_W, 0x00FE); 9117 AscStopQueueExe(iop_base); 9118 if ((AscStopChip(iop_base)) || 9119 (AscGetChipScsiCtrl(iop_base) != 0)) { 9120 asc_dvc->init_state |= ASC_INIT_RESET_SCSI_DONE; 9121 AscResetChipAndScsiBus(asc_dvc); 9122 mdelay(asc_dvc->scsi_reset_wait * 1000); /* XXX: msleep? */ 9123 } 9124 if (!AscIsChipHalted(iop_base)) { 9125 asc_dvc->err_code |= ASC_IERR_START_STOP_CHIP; 9126 return (warn_code); 9127 } 9128 AscSetPCAddr(iop_base, ASC_MCODE_START_ADDR); 9129 if (AscGetPCAddr(iop_base) != ASC_MCODE_START_ADDR) { 9130 asc_dvc->err_code |= ASC_IERR_SET_PC_ADDR; 9131 return (warn_code); 9132 } 9133 eep_config = (ASCEEP_CONFIG *)&eep_config_buf; 9134 cfg_msw = AscGetChipCfgMsw(iop_base); 9135 cfg_lsw = AscGetChipCfgLsw(iop_base); 9136 if ((cfg_msw & ASC_CFG_MSW_CLR_MASK) != 0) { 9137 cfg_msw &= ~ASC_CFG_MSW_CLR_MASK; 9138 warn_code |= ASC_WARN_CFG_MSW_RECOVER; 9139 AscSetChipCfgMsw(iop_base, cfg_msw); 9140 } 9141 chksum = AscGetEEPConfig(iop_base, eep_config, asc_dvc->bus_type); 9142 ASC_DBG(1, "chksum 0x%x\n", chksum); 9143 if (chksum == 0) { 9144 chksum = 0xaa55; 9145 } 9146 if (AscGetChipStatus(iop_base) & CSW_AUTO_CONFIG) { 9147 warn_code |= ASC_WARN_AUTO_CONFIG; 9148 if (asc_dvc->cfg->chip_version == 3) { 9149 if (eep_config->cfg_lsw != cfg_lsw) { 9150 warn_code |= ASC_WARN_EEPROM_RECOVER; 9151 eep_config->cfg_lsw = 9152 AscGetChipCfgLsw(iop_base); 9153 } 9154 if (eep_config->cfg_msw != cfg_msw) { 9155 warn_code |= ASC_WARN_EEPROM_RECOVER; 9156 eep_config->cfg_msw = 9157 AscGetChipCfgMsw(iop_base); 9158 } 9159 } 9160 } 9161 eep_config->cfg_msw &= ~ASC_CFG_MSW_CLR_MASK; 9162 eep_config->cfg_lsw |= ASC_CFG0_HOST_INT_ON; 9163 ASC_DBG(1, "eep_config->chksum 0x%x\n", eep_config->chksum); 9164 if (chksum != eep_config->chksum) { 9165 if (AscGetChipVersion(iop_base, asc_dvc->bus_type) == 9166 ASC_CHIP_VER_PCI_ULTRA_3050) { 9167 ASC_DBG(1, "chksum error ignored; EEPROM-less board\n"); 9168 eep_config->init_sdtr = 0xFF; 9169 eep_config->disc_enable = 0xFF; 9170 eep_config->start_motor = 0xFF; 9171 eep_config->use_cmd_qng = 0; 9172 eep_config->max_total_qng = 0xF0; 9173 eep_config->max_tag_qng = 0x20; 9174 eep_config->cntl = 0xBFFF; 9175 ASC_EEP_SET_CHIP_ID(eep_config, 7); 9176 eep_config->no_scam = 0; 9177 eep_config->adapter_info[0] = 0; 9178 eep_config->adapter_info[1] = 0; 9179 eep_config->adapter_info[2] = 0; 9180 eep_config->adapter_info[3] = 0; 9181 eep_config->adapter_info[4] = 0; 9182 /* Indicate EEPROM-less board. */ 9183 eep_config->adapter_info[5] = 0xBB; 9184 } else { 9185 ASC_PRINT 9186 ("AscInitFromEEP: EEPROM checksum error; Will try to re-write EEPROM.\n"); 9187 write_eep = 1; 9188 warn_code |= ASC_WARN_EEPROM_CHKSUM; 9189 } 9190 } 9191 asc_dvc->cfg->sdtr_enable = eep_config->init_sdtr; 9192 asc_dvc->cfg->disc_enable = eep_config->disc_enable; 9193 asc_dvc->cfg->cmd_qng_enabled = eep_config->use_cmd_qng; 9194 asc_dvc->cfg->isa_dma_speed = ASC_EEP_GET_DMA_SPD(eep_config); 9195 asc_dvc->start_motor = eep_config->start_motor; 9196 asc_dvc->dvc_cntl = eep_config->cntl; 9197 asc_dvc->no_scam = eep_config->no_scam; 9198 asc_dvc->cfg->adapter_info[0] = eep_config->adapter_info[0]; 9199 asc_dvc->cfg->adapter_info[1] = eep_config->adapter_info[1]; 9200 asc_dvc->cfg->adapter_info[2] = eep_config->adapter_info[2]; 9201 asc_dvc->cfg->adapter_info[3] = eep_config->adapter_info[3]; 9202 asc_dvc->cfg->adapter_info[4] = eep_config->adapter_info[4]; 9203 asc_dvc->cfg->adapter_info[5] = eep_config->adapter_info[5]; 9204 if (!AscTestExternalLram(asc_dvc)) { 9205 if (((asc_dvc->bus_type & ASC_IS_PCI_ULTRA) == 9206 ASC_IS_PCI_ULTRA)) { 9207 eep_config->max_total_qng = 9208 ASC_MAX_PCI_ULTRA_INRAM_TOTAL_QNG; 9209 eep_config->max_tag_qng = 9210 ASC_MAX_PCI_ULTRA_INRAM_TAG_QNG; 9211 } else { 9212 eep_config->cfg_msw |= 0x0800; 9213 cfg_msw |= 0x0800; 9214 AscSetChipCfgMsw(iop_base, cfg_msw); 9215 eep_config->max_total_qng = ASC_MAX_PCI_INRAM_TOTAL_QNG; 9216 eep_config->max_tag_qng = ASC_MAX_INRAM_TAG_QNG; 9217 } 9218 } else { 9219 } 9220 if (eep_config->max_total_qng < ASC_MIN_TOTAL_QNG) { 9221 eep_config->max_total_qng = ASC_MIN_TOTAL_QNG; 9222 } 9223 if (eep_config->max_total_qng > ASC_MAX_TOTAL_QNG) { 9224 eep_config->max_total_qng = ASC_MAX_TOTAL_QNG; 9225 } 9226 if (eep_config->max_tag_qng > eep_config->max_total_qng) { 9227 eep_config->max_tag_qng = eep_config->max_total_qng; 9228 } 9229 if (eep_config->max_tag_qng < ASC_MIN_TAG_Q_PER_DVC) { 9230 eep_config->max_tag_qng = ASC_MIN_TAG_Q_PER_DVC; 9231 } 9232 asc_dvc->max_total_qng = eep_config->max_total_qng; 9233 if ((eep_config->use_cmd_qng & eep_config->disc_enable) != 9234 eep_config->use_cmd_qng) { 9235 eep_config->disc_enable = eep_config->use_cmd_qng; 9236 warn_code |= ASC_WARN_CMD_QNG_CONFLICT; 9237 } 9238 ASC_EEP_SET_CHIP_ID(eep_config, 9239 ASC_EEP_GET_CHIP_ID(eep_config) & ASC_MAX_TID); 9240 asc_dvc->cfg->chip_scsi_id = ASC_EEP_GET_CHIP_ID(eep_config); 9241 if (((asc_dvc->bus_type & ASC_IS_PCI_ULTRA) == ASC_IS_PCI_ULTRA) && 9242 !(asc_dvc->dvc_cntl & ASC_CNTL_SDTR_ENABLE_ULTRA)) { 9243 asc_dvc->min_sdtr_index = ASC_SDTR_ULTRA_PCI_10MB_INDEX; 9244 } 9245 9246 for (i = 0; i <= ASC_MAX_TID; i++) { 9247 asc_dvc->dos_int13_table[i] = eep_config->dos_int13_table[i]; 9248 asc_dvc->cfg->max_tag_qng[i] = eep_config->max_tag_qng; 9249 asc_dvc->cfg->sdtr_period_offset[i] = 9250 (uchar)(ASC_DEF_SDTR_OFFSET | 9251 (asc_dvc->min_sdtr_index << 4)); 9252 } 9253 eep_config->cfg_msw = AscGetChipCfgMsw(iop_base); 9254 if (write_eep) { 9255 if ((i = AscSetEEPConfig(iop_base, eep_config, 9256 asc_dvc->bus_type)) != 0) { 9257 ASC_PRINT1 9258 ("AscInitFromEEP: Failed to re-write EEPROM with %d errors.\n", 9259 i); 9260 } else { 9261 ASC_PRINT 9262 ("AscInitFromEEP: Successfully re-wrote EEPROM.\n"); 9263 } 9264 } 9265 return (warn_code); 9266 } 9267 9268 static int AscInitGetConfig(struct Scsi_Host *shost) 9269 { 9270 struct asc_board *board = shost_priv(shost); 9271 ASC_DVC_VAR *asc_dvc = &board->dvc_var.asc_dvc_var; 9272 unsigned short warn_code = 0; 9273 9274 asc_dvc->init_state = ASC_INIT_STATE_BEG_GET_CFG; 9275 if (asc_dvc->err_code != 0) 9276 return asc_dvc->err_code; 9277 9278 if (AscFindSignature(asc_dvc->iop_base)) { 9279 AscInitAscDvcVar(asc_dvc); 9280 warn_code = AscInitFromEEP(asc_dvc); 9281 asc_dvc->init_state |= ASC_INIT_STATE_END_GET_CFG; 9282 if (asc_dvc->scsi_reset_wait > ASC_MAX_SCSI_RESET_WAIT) 9283 asc_dvc->scsi_reset_wait = ASC_MAX_SCSI_RESET_WAIT; 9284 } else { 9285 asc_dvc->err_code = ASC_IERR_BAD_SIGNATURE; 9286 } 9287 9288 switch (warn_code) { 9289 case 0: /* No error */ 9290 break; 9291 case ASC_WARN_IO_PORT_ROTATE: 9292 shost_printk(KERN_WARNING, shost, "I/O port address " 9293 "modified\n"); 9294 break; 9295 case ASC_WARN_AUTO_CONFIG: 9296 shost_printk(KERN_WARNING, shost, "I/O port increment switch " 9297 "enabled\n"); 9298 break; 9299 case ASC_WARN_EEPROM_CHKSUM: 9300 shost_printk(KERN_WARNING, shost, "EEPROM checksum error\n"); 9301 break; 9302 case ASC_WARN_IRQ_MODIFIED: 9303 shost_printk(KERN_WARNING, shost, "IRQ modified\n"); 9304 break; 9305 case ASC_WARN_CMD_QNG_CONFLICT: 9306 shost_printk(KERN_WARNING, shost, "tag queuing enabled w/o " 9307 "disconnects\n"); 9308 break; 9309 default: 9310 shost_printk(KERN_WARNING, shost, "unknown warning: 0x%x\n", 9311 warn_code); 9312 break; 9313 } 9314 9315 if (asc_dvc->err_code != 0) 9316 shost_printk(KERN_ERR, shost, "error 0x%x at init_state " 9317 "0x%x\n", asc_dvc->err_code, asc_dvc->init_state); 9318 9319 return asc_dvc->err_code; 9320 } 9321 9322 static int AscInitSetConfig(struct pci_dev *pdev, struct Scsi_Host *shost) 9323 { 9324 struct asc_board *board = shost_priv(shost); 9325 ASC_DVC_VAR *asc_dvc = &board->dvc_var.asc_dvc_var; 9326 PortAddr iop_base = asc_dvc->iop_base; 9327 unsigned short cfg_msw; 9328 unsigned short warn_code = 0; 9329 9330 asc_dvc->init_state |= ASC_INIT_STATE_BEG_SET_CFG; 9331 if (asc_dvc->err_code != 0) 9332 return asc_dvc->err_code; 9333 if (!AscFindSignature(asc_dvc->iop_base)) { 9334 asc_dvc->err_code = ASC_IERR_BAD_SIGNATURE; 9335 return asc_dvc->err_code; 9336 } 9337 9338 cfg_msw = AscGetChipCfgMsw(iop_base); 9339 if ((cfg_msw & ASC_CFG_MSW_CLR_MASK) != 0) { 9340 cfg_msw &= ~ASC_CFG_MSW_CLR_MASK; 9341 warn_code |= ASC_WARN_CFG_MSW_RECOVER; 9342 AscSetChipCfgMsw(iop_base, cfg_msw); 9343 } 9344 if ((asc_dvc->cfg->cmd_qng_enabled & asc_dvc->cfg->disc_enable) != 9345 asc_dvc->cfg->cmd_qng_enabled) { 9346 asc_dvc->cfg->disc_enable = asc_dvc->cfg->cmd_qng_enabled; 9347 warn_code |= ASC_WARN_CMD_QNG_CONFLICT; 9348 } 9349 if (AscGetChipStatus(iop_base) & CSW_AUTO_CONFIG) { 9350 warn_code |= ASC_WARN_AUTO_CONFIG; 9351 } 9352 #ifdef CONFIG_PCI 9353 if (asc_dvc->bus_type & ASC_IS_PCI) { 9354 cfg_msw &= 0xFFC0; 9355 AscSetChipCfgMsw(iop_base, cfg_msw); 9356 if ((asc_dvc->bus_type & ASC_IS_PCI_ULTRA) == ASC_IS_PCI_ULTRA) { 9357 } else { 9358 if ((pdev->device == PCI_DEVICE_ID_ASP_1200A) || 9359 (pdev->device == PCI_DEVICE_ID_ASP_ABP940)) { 9360 asc_dvc->bug_fix_cntl |= ASC_BUG_FIX_IF_NOT_DWB; 9361 asc_dvc->bug_fix_cntl |= 9362 ASC_BUG_FIX_ASYN_USE_SYN; 9363 } 9364 } 9365 } else 9366 #endif /* CONFIG_PCI */ 9367 if (asc_dvc->bus_type == ASC_IS_ISAPNP) { 9368 if (AscGetChipVersion(iop_base, asc_dvc->bus_type) 9369 == ASC_CHIP_VER_ASYN_BUG) { 9370 asc_dvc->bug_fix_cntl |= ASC_BUG_FIX_ASYN_USE_SYN; 9371 } 9372 } 9373 if (AscSetChipScsiID(iop_base, asc_dvc->cfg->chip_scsi_id) != 9374 asc_dvc->cfg->chip_scsi_id) { 9375 asc_dvc->err_code |= ASC_IERR_SET_SCSI_ID; 9376 } 9377 #ifdef CONFIG_ISA 9378 if (asc_dvc->bus_type & ASC_IS_ISA) { 9379 AscSetIsaDmaChannel(iop_base, asc_dvc->cfg->isa_dma_channel); 9380 AscSetIsaDmaSpeed(iop_base, asc_dvc->cfg->isa_dma_speed); 9381 } 9382 #endif /* CONFIG_ISA */ 9383 9384 asc_dvc->init_state |= ASC_INIT_STATE_END_SET_CFG; 9385 9386 switch (warn_code) { 9387 case 0: /* No error. */ 9388 break; 9389 case ASC_WARN_IO_PORT_ROTATE: 9390 shost_printk(KERN_WARNING, shost, "I/O port address " 9391 "modified\n"); 9392 break; 9393 case ASC_WARN_AUTO_CONFIG: 9394 shost_printk(KERN_WARNING, shost, "I/O port increment switch " 9395 "enabled\n"); 9396 break; 9397 case ASC_WARN_EEPROM_CHKSUM: 9398 shost_printk(KERN_WARNING, shost, "EEPROM checksum error\n"); 9399 break; 9400 case ASC_WARN_IRQ_MODIFIED: 9401 shost_printk(KERN_WARNING, shost, "IRQ modified\n"); 9402 break; 9403 case ASC_WARN_CMD_QNG_CONFLICT: 9404 shost_printk(KERN_WARNING, shost, "tag queuing w/o " 9405 "disconnects\n"); 9406 break; 9407 default: 9408 shost_printk(KERN_WARNING, shost, "unknown warning: 0x%x\n", 9409 warn_code); 9410 break; 9411 } 9412 9413 if (asc_dvc->err_code != 0) 9414 shost_printk(KERN_ERR, shost, "error 0x%x at init_state " 9415 "0x%x\n", asc_dvc->err_code, asc_dvc->init_state); 9416 9417 return asc_dvc->err_code; 9418 } 9419 9420 /* 9421 * EEPROM Configuration. 9422 * 9423 * All drivers should use this structure to set the default EEPROM 9424 * configuration. The BIOS now uses this structure when it is built. 9425 * Additional structure information can be found in a_condor.h where 9426 * the structure is defined. 9427 * 9428 * The *_Field_IsChar structs are needed to correct for endianness. 9429 * These values are read from the board 16 bits at a time directly 9430 * into the structs. Because some fields are char, the values will be 9431 * in the wrong order. The *_Field_IsChar tells when to flip the 9432 * bytes. Data read and written to PCI memory is automatically swapped 9433 * on big-endian platforms so char fields read as words are actually being 9434 * unswapped on big-endian platforms. 9435 */ 9436 #ifdef CONFIG_PCI 9437 static ADVEEP_3550_CONFIG Default_3550_EEPROM_Config = { 9438 ADV_EEPROM_BIOS_ENABLE, /* cfg_lsw */ 9439 0x0000, /* cfg_msw */ 9440 0xFFFF, /* disc_enable */ 9441 0xFFFF, /* wdtr_able */ 9442 0xFFFF, /* sdtr_able */ 9443 0xFFFF, /* start_motor */ 9444 0xFFFF, /* tagqng_able */ 9445 0xFFFF, /* bios_scan */ 9446 0, /* scam_tolerant */ 9447 7, /* adapter_scsi_id */ 9448 0, /* bios_boot_delay */ 9449 3, /* scsi_reset_delay */ 9450 0, /* bios_id_lun */ 9451 0, /* termination */ 9452 0, /* reserved1 */ 9453 0xFFE7, /* bios_ctrl */ 9454 0xFFFF, /* ultra_able */ 9455 0, /* reserved2 */ 9456 ASC_DEF_MAX_HOST_QNG, /* max_host_qng */ 9457 ASC_DEF_MAX_DVC_QNG, /* max_dvc_qng */ 9458 0, /* dvc_cntl */ 9459 0, /* bug_fix */ 9460 0, /* serial_number_word1 */ 9461 0, /* serial_number_word2 */ 9462 0, /* serial_number_word3 */ 9463 0, /* check_sum */ 9464 {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} 9465 , /* oem_name[16] */ 9466 0, /* dvc_err_code */ 9467 0, /* adv_err_code */ 9468 0, /* adv_err_addr */ 9469 0, /* saved_dvc_err_code */ 9470 0, /* saved_adv_err_code */ 9471 0, /* saved_adv_err_addr */ 9472 0 /* num_of_err */ 9473 }; 9474 9475 static ADVEEP_3550_CONFIG ADVEEP_3550_Config_Field_IsChar = { 9476 0, /* cfg_lsw */ 9477 0, /* cfg_msw */ 9478 0, /* -disc_enable */ 9479 0, /* wdtr_able */ 9480 0, /* sdtr_able */ 9481 0, /* start_motor */ 9482 0, /* tagqng_able */ 9483 0, /* bios_scan */ 9484 0, /* scam_tolerant */ 9485 1, /* adapter_scsi_id */ 9486 1, /* bios_boot_delay */ 9487 1, /* scsi_reset_delay */ 9488 1, /* bios_id_lun */ 9489 1, /* termination */ 9490 1, /* reserved1 */ 9491 0, /* bios_ctrl */ 9492 0, /* ultra_able */ 9493 0, /* reserved2 */ 9494 1, /* max_host_qng */ 9495 1, /* max_dvc_qng */ 9496 0, /* dvc_cntl */ 9497 0, /* bug_fix */ 9498 0, /* serial_number_word1 */ 9499 0, /* serial_number_word2 */ 9500 0, /* serial_number_word3 */ 9501 0, /* check_sum */ 9502 {1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1} 9503 , /* oem_name[16] */ 9504 0, /* dvc_err_code */ 9505 0, /* adv_err_code */ 9506 0, /* adv_err_addr */ 9507 0, /* saved_dvc_err_code */ 9508 0, /* saved_adv_err_code */ 9509 0, /* saved_adv_err_addr */ 9510 0 /* num_of_err */ 9511 }; 9512 9513 static ADVEEP_38C0800_CONFIG Default_38C0800_EEPROM_Config = { 9514 ADV_EEPROM_BIOS_ENABLE, /* 00 cfg_lsw */ 9515 0x0000, /* 01 cfg_msw */ 9516 0xFFFF, /* 02 disc_enable */ 9517 0xFFFF, /* 03 wdtr_able */ 9518 0x4444, /* 04 sdtr_speed1 */ 9519 0xFFFF, /* 05 start_motor */ 9520 0xFFFF, /* 06 tagqng_able */ 9521 0xFFFF, /* 07 bios_scan */ 9522 0, /* 08 scam_tolerant */ 9523 7, /* 09 adapter_scsi_id */ 9524 0, /* bios_boot_delay */ 9525 3, /* 10 scsi_reset_delay */ 9526 0, /* bios_id_lun */ 9527 0, /* 11 termination_se */ 9528 0, /* termination_lvd */ 9529 0xFFE7, /* 12 bios_ctrl */ 9530 0x4444, /* 13 sdtr_speed2 */ 9531 0x4444, /* 14 sdtr_speed3 */ 9532 ASC_DEF_MAX_HOST_QNG, /* 15 max_host_qng */ 9533 ASC_DEF_MAX_DVC_QNG, /* max_dvc_qng */ 9534 0, /* 16 dvc_cntl */ 9535 0x4444, /* 17 sdtr_speed4 */ 9536 0, /* 18 serial_number_word1 */ 9537 0, /* 19 serial_number_word2 */ 9538 0, /* 20 serial_number_word3 */ 9539 0, /* 21 check_sum */ 9540 {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} 9541 , /* 22-29 oem_name[16] */ 9542 0, /* 30 dvc_err_code */ 9543 0, /* 31 adv_err_code */ 9544 0, /* 32 adv_err_addr */ 9545 0, /* 33 saved_dvc_err_code */ 9546 0, /* 34 saved_adv_err_code */ 9547 0, /* 35 saved_adv_err_addr */ 9548 0, /* 36 reserved */ 9549 0, /* 37 reserved */ 9550 0, /* 38 reserved */ 9551 0, /* 39 reserved */ 9552 0, /* 40 reserved */ 9553 0, /* 41 reserved */ 9554 0, /* 42 reserved */ 9555 0, /* 43 reserved */ 9556 0, /* 44 reserved */ 9557 0, /* 45 reserved */ 9558 0, /* 46 reserved */ 9559 0, /* 47 reserved */ 9560 0, /* 48 reserved */ 9561 0, /* 49 reserved */ 9562 0, /* 50 reserved */ 9563 0, /* 51 reserved */ 9564 0, /* 52 reserved */ 9565 0, /* 53 reserved */ 9566 0, /* 54 reserved */ 9567 0, /* 55 reserved */ 9568 0, /* 56 cisptr_lsw */ 9569 0, /* 57 cisprt_msw */ 9570 PCI_VENDOR_ID_ASP, /* 58 subsysvid */ 9571 PCI_DEVICE_ID_38C0800_REV1, /* 59 subsysid */ 9572 0, /* 60 reserved */ 9573 0, /* 61 reserved */ 9574 0, /* 62 reserved */ 9575 0 /* 63 reserved */ 9576 }; 9577 9578 static ADVEEP_38C0800_CONFIG ADVEEP_38C0800_Config_Field_IsChar = { 9579 0, /* 00 cfg_lsw */ 9580 0, /* 01 cfg_msw */ 9581 0, /* 02 disc_enable */ 9582 0, /* 03 wdtr_able */ 9583 0, /* 04 sdtr_speed1 */ 9584 0, /* 05 start_motor */ 9585 0, /* 06 tagqng_able */ 9586 0, /* 07 bios_scan */ 9587 0, /* 08 scam_tolerant */ 9588 1, /* 09 adapter_scsi_id */ 9589 1, /* bios_boot_delay */ 9590 1, /* 10 scsi_reset_delay */ 9591 1, /* bios_id_lun */ 9592 1, /* 11 termination_se */ 9593 1, /* termination_lvd */ 9594 0, /* 12 bios_ctrl */ 9595 0, /* 13 sdtr_speed2 */ 9596 0, /* 14 sdtr_speed3 */ 9597 1, /* 15 max_host_qng */ 9598 1, /* max_dvc_qng */ 9599 0, /* 16 dvc_cntl */ 9600 0, /* 17 sdtr_speed4 */ 9601 0, /* 18 serial_number_word1 */ 9602 0, /* 19 serial_number_word2 */ 9603 0, /* 20 serial_number_word3 */ 9604 0, /* 21 check_sum */ 9605 {1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1} 9606 , /* 22-29 oem_name[16] */ 9607 0, /* 30 dvc_err_code */ 9608 0, /* 31 adv_err_code */ 9609 0, /* 32 adv_err_addr */ 9610 0, /* 33 saved_dvc_err_code */ 9611 0, /* 34 saved_adv_err_code */ 9612 0, /* 35 saved_adv_err_addr */ 9613 0, /* 36 reserved */ 9614 0, /* 37 reserved */ 9615 0, /* 38 reserved */ 9616 0, /* 39 reserved */ 9617 0, /* 40 reserved */ 9618 0, /* 41 reserved */ 9619 0, /* 42 reserved */ 9620 0, /* 43 reserved */ 9621 0, /* 44 reserved */ 9622 0, /* 45 reserved */ 9623 0, /* 46 reserved */ 9624 0, /* 47 reserved */ 9625 0, /* 48 reserved */ 9626 0, /* 49 reserved */ 9627 0, /* 50 reserved */ 9628 0, /* 51 reserved */ 9629 0, /* 52 reserved */ 9630 0, /* 53 reserved */ 9631 0, /* 54 reserved */ 9632 0, /* 55 reserved */ 9633 0, /* 56 cisptr_lsw */ 9634 0, /* 57 cisprt_msw */ 9635 0, /* 58 subsysvid */ 9636 0, /* 59 subsysid */ 9637 0, /* 60 reserved */ 9638 0, /* 61 reserved */ 9639 0, /* 62 reserved */ 9640 0 /* 63 reserved */ 9641 }; 9642 9643 static ADVEEP_38C1600_CONFIG Default_38C1600_EEPROM_Config = { 9644 ADV_EEPROM_BIOS_ENABLE, /* 00 cfg_lsw */ 9645 0x0000, /* 01 cfg_msw */ 9646 0xFFFF, /* 02 disc_enable */ 9647 0xFFFF, /* 03 wdtr_able */ 9648 0x5555, /* 04 sdtr_speed1 */ 9649 0xFFFF, /* 05 start_motor */ 9650 0xFFFF, /* 06 tagqng_able */ 9651 0xFFFF, /* 07 bios_scan */ 9652 0, /* 08 scam_tolerant */ 9653 7, /* 09 adapter_scsi_id */ 9654 0, /* bios_boot_delay */ 9655 3, /* 10 scsi_reset_delay */ 9656 0, /* bios_id_lun */ 9657 0, /* 11 termination_se */ 9658 0, /* termination_lvd */ 9659 0xFFE7, /* 12 bios_ctrl */ 9660 0x5555, /* 13 sdtr_speed2 */ 9661 0x5555, /* 14 sdtr_speed3 */ 9662 ASC_DEF_MAX_HOST_QNG, /* 15 max_host_qng */ 9663 ASC_DEF_MAX_DVC_QNG, /* max_dvc_qng */ 9664 0, /* 16 dvc_cntl */ 9665 0x5555, /* 17 sdtr_speed4 */ 9666 0, /* 18 serial_number_word1 */ 9667 0, /* 19 serial_number_word2 */ 9668 0, /* 20 serial_number_word3 */ 9669 0, /* 21 check_sum */ 9670 {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} 9671 , /* 22-29 oem_name[16] */ 9672 0, /* 30 dvc_err_code */ 9673 0, /* 31 adv_err_code */ 9674 0, /* 32 adv_err_addr */ 9675 0, /* 33 saved_dvc_err_code */ 9676 0, /* 34 saved_adv_err_code */ 9677 0, /* 35 saved_adv_err_addr */ 9678 0, /* 36 reserved */ 9679 0, /* 37 reserved */ 9680 0, /* 38 reserved */ 9681 0, /* 39 reserved */ 9682 0, /* 40 reserved */ 9683 0, /* 41 reserved */ 9684 0, /* 42 reserved */ 9685 0, /* 43 reserved */ 9686 0, /* 44 reserved */ 9687 0, /* 45 reserved */ 9688 0, /* 46 reserved */ 9689 0, /* 47 reserved */ 9690 0, /* 48 reserved */ 9691 0, /* 49 reserved */ 9692 0, /* 50 reserved */ 9693 0, /* 51 reserved */ 9694 0, /* 52 reserved */ 9695 0, /* 53 reserved */ 9696 0, /* 54 reserved */ 9697 0, /* 55 reserved */ 9698 0, /* 56 cisptr_lsw */ 9699 0, /* 57 cisprt_msw */ 9700 PCI_VENDOR_ID_ASP, /* 58 subsysvid */ 9701 PCI_DEVICE_ID_38C1600_REV1, /* 59 subsysid */ 9702 0, /* 60 reserved */ 9703 0, /* 61 reserved */ 9704 0, /* 62 reserved */ 9705 0 /* 63 reserved */ 9706 }; 9707 9708 static ADVEEP_38C1600_CONFIG ADVEEP_38C1600_Config_Field_IsChar = { 9709 0, /* 00 cfg_lsw */ 9710 0, /* 01 cfg_msw */ 9711 0, /* 02 disc_enable */ 9712 0, /* 03 wdtr_able */ 9713 0, /* 04 sdtr_speed1 */ 9714 0, /* 05 start_motor */ 9715 0, /* 06 tagqng_able */ 9716 0, /* 07 bios_scan */ 9717 0, /* 08 scam_tolerant */ 9718 1, /* 09 adapter_scsi_id */ 9719 1, /* bios_boot_delay */ 9720 1, /* 10 scsi_reset_delay */ 9721 1, /* bios_id_lun */ 9722 1, /* 11 termination_se */ 9723 1, /* termination_lvd */ 9724 0, /* 12 bios_ctrl */ 9725 0, /* 13 sdtr_speed2 */ 9726 0, /* 14 sdtr_speed3 */ 9727 1, /* 15 max_host_qng */ 9728 1, /* max_dvc_qng */ 9729 0, /* 16 dvc_cntl */ 9730 0, /* 17 sdtr_speed4 */ 9731 0, /* 18 serial_number_word1 */ 9732 0, /* 19 serial_number_word2 */ 9733 0, /* 20 serial_number_word3 */ 9734 0, /* 21 check_sum */ 9735 {1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1} 9736 , /* 22-29 oem_name[16] */ 9737 0, /* 30 dvc_err_code */ 9738 0, /* 31 adv_err_code */ 9739 0, /* 32 adv_err_addr */ 9740 0, /* 33 saved_dvc_err_code */ 9741 0, /* 34 saved_adv_err_code */ 9742 0, /* 35 saved_adv_err_addr */ 9743 0, /* 36 reserved */ 9744 0, /* 37 reserved */ 9745 0, /* 38 reserved */ 9746 0, /* 39 reserved */ 9747 0, /* 40 reserved */ 9748 0, /* 41 reserved */ 9749 0, /* 42 reserved */ 9750 0, /* 43 reserved */ 9751 0, /* 44 reserved */ 9752 0, /* 45 reserved */ 9753 0, /* 46 reserved */ 9754 0, /* 47 reserved */ 9755 0, /* 48 reserved */ 9756 0, /* 49 reserved */ 9757 0, /* 50 reserved */ 9758 0, /* 51 reserved */ 9759 0, /* 52 reserved */ 9760 0, /* 53 reserved */ 9761 0, /* 54 reserved */ 9762 0, /* 55 reserved */ 9763 0, /* 56 cisptr_lsw */ 9764 0, /* 57 cisprt_msw */ 9765 0, /* 58 subsysvid */ 9766 0, /* 59 subsysid */ 9767 0, /* 60 reserved */ 9768 0, /* 61 reserved */ 9769 0, /* 62 reserved */ 9770 0 /* 63 reserved */ 9771 }; 9772 9773 /* 9774 * Wait for EEPROM command to complete 9775 */ 9776 static void AdvWaitEEPCmd(AdvPortAddr iop_base) 9777 { 9778 int eep_delay_ms; 9779 9780 for (eep_delay_ms = 0; eep_delay_ms < ADV_EEP_DELAY_MS; eep_delay_ms++) { 9781 if (AdvReadWordRegister(iop_base, IOPW_EE_CMD) & 9782 ASC_EEP_CMD_DONE) { 9783 break; 9784 } 9785 mdelay(1); 9786 } 9787 if ((AdvReadWordRegister(iop_base, IOPW_EE_CMD) & ASC_EEP_CMD_DONE) == 9788 0) 9789 BUG(); 9790 } 9791 9792 /* 9793 * Read the EEPROM from specified location 9794 */ 9795 static ushort AdvReadEEPWord(AdvPortAddr iop_base, int eep_word_addr) 9796 { 9797 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, 9798 ASC_EEP_CMD_READ | eep_word_addr); 9799 AdvWaitEEPCmd(iop_base); 9800 return AdvReadWordRegister(iop_base, IOPW_EE_DATA); 9801 } 9802 9803 /* 9804 * Write the EEPROM from 'cfg_buf'. 9805 */ 9806 static void AdvSet3550EEPConfig(AdvPortAddr iop_base, 9807 ADVEEP_3550_CONFIG *cfg_buf) 9808 { 9809 ushort *wbuf; 9810 ushort addr, chksum; 9811 ushort *charfields; 9812 9813 wbuf = (ushort *)cfg_buf; 9814 charfields = (ushort *)&ADVEEP_3550_Config_Field_IsChar; 9815 chksum = 0; 9816 9817 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, ASC_EEP_CMD_WRITE_ABLE); 9818 AdvWaitEEPCmd(iop_base); 9819 9820 /* 9821 * Write EEPROM from word 0 to word 20. 9822 */ 9823 for (addr = ADV_EEP_DVC_CFG_BEGIN; 9824 addr < ADV_EEP_DVC_CFG_END; addr++, wbuf++) { 9825 ushort word; 9826 9827 if (*charfields++) { 9828 word = cpu_to_le16(*wbuf); 9829 } else { 9830 word = *wbuf; 9831 } 9832 chksum += *wbuf; /* Checksum is calculated from word values. */ 9833 AdvWriteWordRegister(iop_base, IOPW_EE_DATA, word); 9834 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, 9835 ASC_EEP_CMD_WRITE | addr); 9836 AdvWaitEEPCmd(iop_base); 9837 mdelay(ADV_EEP_DELAY_MS); 9838 } 9839 9840 /* 9841 * Write EEPROM checksum at word 21. 9842 */ 9843 AdvWriteWordRegister(iop_base, IOPW_EE_DATA, chksum); 9844 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, ASC_EEP_CMD_WRITE | addr); 9845 AdvWaitEEPCmd(iop_base); 9846 wbuf++; 9847 charfields++; 9848 9849 /* 9850 * Write EEPROM OEM name at words 22 to 29. 9851 */ 9852 for (addr = ADV_EEP_DVC_CTL_BEGIN; 9853 addr < ADV_EEP_MAX_WORD_ADDR; addr++, wbuf++) { 9854 ushort word; 9855 9856 if (*charfields++) { 9857 word = cpu_to_le16(*wbuf); 9858 } else { 9859 word = *wbuf; 9860 } 9861 AdvWriteWordRegister(iop_base, IOPW_EE_DATA, word); 9862 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, 9863 ASC_EEP_CMD_WRITE | addr); 9864 AdvWaitEEPCmd(iop_base); 9865 } 9866 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, ASC_EEP_CMD_WRITE_DISABLE); 9867 AdvWaitEEPCmd(iop_base); 9868 } 9869 9870 /* 9871 * Write the EEPROM from 'cfg_buf'. 9872 */ 9873 static void AdvSet38C0800EEPConfig(AdvPortAddr iop_base, 9874 ADVEEP_38C0800_CONFIG *cfg_buf) 9875 { 9876 ushort *wbuf; 9877 ushort *charfields; 9878 ushort addr, chksum; 9879 9880 wbuf = (ushort *)cfg_buf; 9881 charfields = (ushort *)&ADVEEP_38C0800_Config_Field_IsChar; 9882 chksum = 0; 9883 9884 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, ASC_EEP_CMD_WRITE_ABLE); 9885 AdvWaitEEPCmd(iop_base); 9886 9887 /* 9888 * Write EEPROM from word 0 to word 20. 9889 */ 9890 for (addr = ADV_EEP_DVC_CFG_BEGIN; 9891 addr < ADV_EEP_DVC_CFG_END; addr++, wbuf++) { 9892 ushort word; 9893 9894 if (*charfields++) { 9895 word = cpu_to_le16(*wbuf); 9896 } else { 9897 word = *wbuf; 9898 } 9899 chksum += *wbuf; /* Checksum is calculated from word values. */ 9900 AdvWriteWordRegister(iop_base, IOPW_EE_DATA, word); 9901 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, 9902 ASC_EEP_CMD_WRITE | addr); 9903 AdvWaitEEPCmd(iop_base); 9904 mdelay(ADV_EEP_DELAY_MS); 9905 } 9906 9907 /* 9908 * Write EEPROM checksum at word 21. 9909 */ 9910 AdvWriteWordRegister(iop_base, IOPW_EE_DATA, chksum); 9911 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, ASC_EEP_CMD_WRITE | addr); 9912 AdvWaitEEPCmd(iop_base); 9913 wbuf++; 9914 charfields++; 9915 9916 /* 9917 * Write EEPROM OEM name at words 22 to 29. 9918 */ 9919 for (addr = ADV_EEP_DVC_CTL_BEGIN; 9920 addr < ADV_EEP_MAX_WORD_ADDR; addr++, wbuf++) { 9921 ushort word; 9922 9923 if (*charfields++) { 9924 word = cpu_to_le16(*wbuf); 9925 } else { 9926 word = *wbuf; 9927 } 9928 AdvWriteWordRegister(iop_base, IOPW_EE_DATA, word); 9929 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, 9930 ASC_EEP_CMD_WRITE | addr); 9931 AdvWaitEEPCmd(iop_base); 9932 } 9933 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, ASC_EEP_CMD_WRITE_DISABLE); 9934 AdvWaitEEPCmd(iop_base); 9935 } 9936 9937 /* 9938 * Write the EEPROM from 'cfg_buf'. 9939 */ 9940 static void AdvSet38C1600EEPConfig(AdvPortAddr iop_base, 9941 ADVEEP_38C1600_CONFIG *cfg_buf) 9942 { 9943 ushort *wbuf; 9944 ushort *charfields; 9945 ushort addr, chksum; 9946 9947 wbuf = (ushort *)cfg_buf; 9948 charfields = (ushort *)&ADVEEP_38C1600_Config_Field_IsChar; 9949 chksum = 0; 9950 9951 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, ASC_EEP_CMD_WRITE_ABLE); 9952 AdvWaitEEPCmd(iop_base); 9953 9954 /* 9955 * Write EEPROM from word 0 to word 20. 9956 */ 9957 for (addr = ADV_EEP_DVC_CFG_BEGIN; 9958 addr < ADV_EEP_DVC_CFG_END; addr++, wbuf++) { 9959 ushort word; 9960 9961 if (*charfields++) { 9962 word = cpu_to_le16(*wbuf); 9963 } else { 9964 word = *wbuf; 9965 } 9966 chksum += *wbuf; /* Checksum is calculated from word values. */ 9967 AdvWriteWordRegister(iop_base, IOPW_EE_DATA, word); 9968 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, 9969 ASC_EEP_CMD_WRITE | addr); 9970 AdvWaitEEPCmd(iop_base); 9971 mdelay(ADV_EEP_DELAY_MS); 9972 } 9973 9974 /* 9975 * Write EEPROM checksum at word 21. 9976 */ 9977 AdvWriteWordRegister(iop_base, IOPW_EE_DATA, chksum); 9978 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, ASC_EEP_CMD_WRITE | addr); 9979 AdvWaitEEPCmd(iop_base); 9980 wbuf++; 9981 charfields++; 9982 9983 /* 9984 * Write EEPROM OEM name at words 22 to 29. 9985 */ 9986 for (addr = ADV_EEP_DVC_CTL_BEGIN; 9987 addr < ADV_EEP_MAX_WORD_ADDR; addr++, wbuf++) { 9988 ushort word; 9989 9990 if (*charfields++) { 9991 word = cpu_to_le16(*wbuf); 9992 } else { 9993 word = *wbuf; 9994 } 9995 AdvWriteWordRegister(iop_base, IOPW_EE_DATA, word); 9996 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, 9997 ASC_EEP_CMD_WRITE | addr); 9998 AdvWaitEEPCmd(iop_base); 9999 } 10000 AdvWriteWordRegister(iop_base, IOPW_EE_CMD, ASC_EEP_CMD_WRITE_DISABLE); 10001 AdvWaitEEPCmd(iop_base); 10002 } 10003 10004 /* 10005 * Read EEPROM configuration into the specified buffer. 10006 * 10007 * Return a checksum based on the EEPROM configuration read. 10008 */ 10009 static ushort AdvGet3550EEPConfig(AdvPortAddr iop_base, 10010 ADVEEP_3550_CONFIG *cfg_buf) 10011 { 10012 ushort wval, chksum; 10013 ushort *wbuf; 10014 int eep_addr; 10015 ushort *charfields; 10016 10017 charfields = (ushort *)&ADVEEP_3550_Config_Field_IsChar; 10018 wbuf = (ushort *)cfg_buf; 10019 chksum = 0; 10020 10021 for (eep_addr = ADV_EEP_DVC_CFG_BEGIN; 10022 eep_addr < ADV_EEP_DVC_CFG_END; eep_addr++, wbuf++) { 10023 wval = AdvReadEEPWord(iop_base, eep_addr); 10024 chksum += wval; /* Checksum is calculated from word values. */ 10025 if (*charfields++) { 10026 *wbuf = le16_to_cpu(wval); 10027 } else { 10028 *wbuf = wval; 10029 } 10030 } 10031 /* Read checksum word. */ 10032 *wbuf = AdvReadEEPWord(iop_base, eep_addr); 10033 wbuf++; 10034 charfields++; 10035 10036 /* Read rest of EEPROM not covered by the checksum. */ 10037 for (eep_addr = ADV_EEP_DVC_CTL_BEGIN; 10038 eep_addr < ADV_EEP_MAX_WORD_ADDR; eep_addr++, wbuf++) { 10039 *wbuf = AdvReadEEPWord(iop_base, eep_addr); 10040 if (*charfields++) { 10041 *wbuf = le16_to_cpu(*wbuf); 10042 } 10043 } 10044 return chksum; 10045 } 10046 10047 /* 10048 * Read EEPROM configuration into the specified buffer. 10049 * 10050 * Return a checksum based on the EEPROM configuration read. 10051 */ 10052 static ushort AdvGet38C0800EEPConfig(AdvPortAddr iop_base, 10053 ADVEEP_38C0800_CONFIG *cfg_buf) 10054 { 10055 ushort wval, chksum; 10056 ushort *wbuf; 10057 int eep_addr; 10058 ushort *charfields; 10059 10060 charfields = (ushort *)&ADVEEP_38C0800_Config_Field_IsChar; 10061 wbuf = (ushort *)cfg_buf; 10062 chksum = 0; 10063 10064 for (eep_addr = ADV_EEP_DVC_CFG_BEGIN; 10065 eep_addr < ADV_EEP_DVC_CFG_END; eep_addr++, wbuf++) { 10066 wval = AdvReadEEPWord(iop_base, eep_addr); 10067 chksum += wval; /* Checksum is calculated from word values. */ 10068 if (*charfields++) { 10069 *wbuf = le16_to_cpu(wval); 10070 } else { 10071 *wbuf = wval; 10072 } 10073 } 10074 /* Read checksum word. */ 10075 *wbuf = AdvReadEEPWord(iop_base, eep_addr); 10076 wbuf++; 10077 charfields++; 10078 10079 /* Read rest of EEPROM not covered by the checksum. */ 10080 for (eep_addr = ADV_EEP_DVC_CTL_BEGIN; 10081 eep_addr < ADV_EEP_MAX_WORD_ADDR; eep_addr++, wbuf++) { 10082 *wbuf = AdvReadEEPWord(iop_base, eep_addr); 10083 if (*charfields++) { 10084 *wbuf = le16_to_cpu(*wbuf); 10085 } 10086 } 10087 return chksum; 10088 } 10089 10090 /* 10091 * Read EEPROM configuration into the specified buffer. 10092 * 10093 * Return a checksum based on the EEPROM configuration read. 10094 */ 10095 static ushort AdvGet38C1600EEPConfig(AdvPortAddr iop_base, 10096 ADVEEP_38C1600_CONFIG *cfg_buf) 10097 { 10098 ushort wval, chksum; 10099 ushort *wbuf; 10100 int eep_addr; 10101 ushort *charfields; 10102 10103 charfields = (ushort *)&ADVEEP_38C1600_Config_Field_IsChar; 10104 wbuf = (ushort *)cfg_buf; 10105 chksum = 0; 10106 10107 for (eep_addr = ADV_EEP_DVC_CFG_BEGIN; 10108 eep_addr < ADV_EEP_DVC_CFG_END; eep_addr++, wbuf++) { 10109 wval = AdvReadEEPWord(iop_base, eep_addr); 10110 chksum += wval; /* Checksum is calculated from word values. */ 10111 if (*charfields++) { 10112 *wbuf = le16_to_cpu(wval); 10113 } else { 10114 *wbuf = wval; 10115 } 10116 } 10117 /* Read checksum word. */ 10118 *wbuf = AdvReadEEPWord(iop_base, eep_addr); 10119 wbuf++; 10120 charfields++; 10121 10122 /* Read rest of EEPROM not covered by the checksum. */ 10123 for (eep_addr = ADV_EEP_DVC_CTL_BEGIN; 10124 eep_addr < ADV_EEP_MAX_WORD_ADDR; eep_addr++, wbuf++) { 10125 *wbuf = AdvReadEEPWord(iop_base, eep_addr); 10126 if (*charfields++) { 10127 *wbuf = le16_to_cpu(*wbuf); 10128 } 10129 } 10130 return chksum; 10131 } 10132 10133 /* 10134 * Read the board's EEPROM configuration. Set fields in ADV_DVC_VAR and 10135 * ADV_DVC_CFG based on the EEPROM settings. The chip is stopped while 10136 * all of this is done. 10137 * 10138 * On failure set the ADV_DVC_VAR field 'err_code' and return ADV_ERROR. 10139 * 10140 * For a non-fatal error return a warning code. If there are no warnings 10141 * then 0 is returned. 10142 * 10143 * Note: Chip is stopped on entry. 10144 */ 10145 static int AdvInitFrom3550EEP(ADV_DVC_VAR *asc_dvc) 10146 { 10147 AdvPortAddr iop_base; 10148 ushort warn_code; 10149 ADVEEP_3550_CONFIG eep_config; 10150 10151 iop_base = asc_dvc->iop_base; 10152 10153 warn_code = 0; 10154 10155 /* 10156 * Read the board's EEPROM configuration. 10157 * 10158 * Set default values if a bad checksum is found. 10159 */ 10160 if (AdvGet3550EEPConfig(iop_base, &eep_config) != eep_config.check_sum) { 10161 warn_code |= ASC_WARN_EEPROM_CHKSUM; 10162 10163 /* 10164 * Set EEPROM default values. 10165 */ 10166 memcpy(&eep_config, &Default_3550_EEPROM_Config, 10167 sizeof(ADVEEP_3550_CONFIG)); 10168 10169 /* 10170 * Assume the 6 byte board serial number that was read from 10171 * EEPROM is correct even if the EEPROM checksum failed. 10172 */ 10173 eep_config.serial_number_word3 = 10174 AdvReadEEPWord(iop_base, ADV_EEP_DVC_CFG_END - 1); 10175 10176 eep_config.serial_number_word2 = 10177 AdvReadEEPWord(iop_base, ADV_EEP_DVC_CFG_END - 2); 10178 10179 eep_config.serial_number_word1 = 10180 AdvReadEEPWord(iop_base, ADV_EEP_DVC_CFG_END - 3); 10181 10182 AdvSet3550EEPConfig(iop_base, &eep_config); 10183 } 10184 /* 10185 * Set ASC_DVC_VAR and ASC_DVC_CFG variables from the 10186 * EEPROM configuration that was read. 10187 * 10188 * This is the mapping of EEPROM fields to Adv Library fields. 10189 */ 10190 asc_dvc->wdtr_able = eep_config.wdtr_able; 10191 asc_dvc->sdtr_able = eep_config.sdtr_able; 10192 asc_dvc->ultra_able = eep_config.ultra_able; 10193 asc_dvc->tagqng_able = eep_config.tagqng_able; 10194 asc_dvc->cfg->disc_enable = eep_config.disc_enable; 10195 asc_dvc->max_host_qng = eep_config.max_host_qng; 10196 asc_dvc->max_dvc_qng = eep_config.max_dvc_qng; 10197 asc_dvc->chip_scsi_id = (eep_config.adapter_scsi_id & ADV_MAX_TID); 10198 asc_dvc->start_motor = eep_config.start_motor; 10199 asc_dvc->scsi_reset_wait = eep_config.scsi_reset_delay; 10200 asc_dvc->bios_ctrl = eep_config.bios_ctrl; 10201 asc_dvc->no_scam = eep_config.scam_tolerant; 10202 asc_dvc->cfg->serial1 = eep_config.serial_number_word1; 10203 asc_dvc->cfg->serial2 = eep_config.serial_number_word2; 10204 asc_dvc->cfg->serial3 = eep_config.serial_number_word3; 10205 10206 /* 10207 * Set the host maximum queuing (max. 253, min. 16) and the per device 10208 * maximum queuing (max. 63, min. 4). 10209 */ 10210 if (eep_config.max_host_qng > ASC_DEF_MAX_HOST_QNG) { 10211 eep_config.max_host_qng = ASC_DEF_MAX_HOST_QNG; 10212 } else if (eep_config.max_host_qng < ASC_DEF_MIN_HOST_QNG) { 10213 /* If the value is zero, assume it is uninitialized. */ 10214 if (eep_config.max_host_qng == 0) { 10215 eep_config.max_host_qng = ASC_DEF_MAX_HOST_QNG; 10216 } else { 10217 eep_config.max_host_qng = ASC_DEF_MIN_HOST_QNG; 10218 } 10219 } 10220 10221 if (eep_config.max_dvc_qng > ASC_DEF_MAX_DVC_QNG) { 10222 eep_config.max_dvc_qng = ASC_DEF_MAX_DVC_QNG; 10223 } else if (eep_config.max_dvc_qng < ASC_DEF_MIN_DVC_QNG) { 10224 /* If the value is zero, assume it is uninitialized. */ 10225 if (eep_config.max_dvc_qng == 0) { 10226 eep_config.max_dvc_qng = ASC_DEF_MAX_DVC_QNG; 10227 } else { 10228 eep_config.max_dvc_qng = ASC_DEF_MIN_DVC_QNG; 10229 } 10230 } 10231 10232 /* 10233 * If 'max_dvc_qng' is greater than 'max_host_qng', then 10234 * set 'max_dvc_qng' to 'max_host_qng'. 10235 */ 10236 if (eep_config.max_dvc_qng > eep_config.max_host_qng) { 10237 eep_config.max_dvc_qng = eep_config.max_host_qng; 10238 } 10239 10240 /* 10241 * Set ADV_DVC_VAR 'max_host_qng' and ADV_DVC_VAR 'max_dvc_qng' 10242 * values based on possibly adjusted EEPROM values. 10243 */ 10244 asc_dvc->max_host_qng = eep_config.max_host_qng; 10245 asc_dvc->max_dvc_qng = eep_config.max_dvc_qng; 10246 10247 /* 10248 * If the EEPROM 'termination' field is set to automatic (0), then set 10249 * the ADV_DVC_CFG 'termination' field to automatic also. 10250 * 10251 * If the termination is specified with a non-zero 'termination' 10252 * value check that a legal value is set and set the ADV_DVC_CFG 10253 * 'termination' field appropriately. 10254 */ 10255 if (eep_config.termination == 0) { 10256 asc_dvc->cfg->termination = 0; /* auto termination */ 10257 } else { 10258 /* Enable manual control with low off / high off. */ 10259 if (eep_config.termination == 1) { 10260 asc_dvc->cfg->termination = TERM_CTL_SEL; 10261 10262 /* Enable manual control with low off / high on. */ 10263 } else if (eep_config.termination == 2) { 10264 asc_dvc->cfg->termination = TERM_CTL_SEL | TERM_CTL_H; 10265 10266 /* Enable manual control with low on / high on. */ 10267 } else if (eep_config.termination == 3) { 10268 asc_dvc->cfg->termination = 10269 TERM_CTL_SEL | TERM_CTL_H | TERM_CTL_L; 10270 } else { 10271 /* 10272 * The EEPROM 'termination' field contains a bad value. Use 10273 * automatic termination instead. 10274 */ 10275 asc_dvc->cfg->termination = 0; 10276 warn_code |= ASC_WARN_EEPROM_TERMINATION; 10277 } 10278 } 10279 10280 return warn_code; 10281 } 10282 10283 /* 10284 * Read the board's EEPROM configuration. Set fields in ADV_DVC_VAR and 10285 * ADV_DVC_CFG based on the EEPROM settings. The chip is stopped while 10286 * all of this is done. 10287 * 10288 * On failure set the ADV_DVC_VAR field 'err_code' and return ADV_ERROR. 10289 * 10290 * For a non-fatal error return a warning code. If there are no warnings 10291 * then 0 is returned. 10292 * 10293 * Note: Chip is stopped on entry. 10294 */ 10295 static int AdvInitFrom38C0800EEP(ADV_DVC_VAR *asc_dvc) 10296 { 10297 AdvPortAddr iop_base; 10298 ushort warn_code; 10299 ADVEEP_38C0800_CONFIG eep_config; 10300 uchar tid, termination; 10301 ushort sdtr_speed = 0; 10302 10303 iop_base = asc_dvc->iop_base; 10304 10305 warn_code = 0; 10306 10307 /* 10308 * Read the board's EEPROM configuration. 10309 * 10310 * Set default values if a bad checksum is found. 10311 */ 10312 if (AdvGet38C0800EEPConfig(iop_base, &eep_config) != 10313 eep_config.check_sum) { 10314 warn_code |= ASC_WARN_EEPROM_CHKSUM; 10315 10316 /* 10317 * Set EEPROM default values. 10318 */ 10319 memcpy(&eep_config, &Default_38C0800_EEPROM_Config, 10320 sizeof(ADVEEP_38C0800_CONFIG)); 10321 10322 /* 10323 * Assume the 6 byte board serial number that was read from 10324 * EEPROM is correct even if the EEPROM checksum failed. 10325 */ 10326 eep_config.serial_number_word3 = 10327 AdvReadEEPWord(iop_base, ADV_EEP_DVC_CFG_END - 1); 10328 10329 eep_config.serial_number_word2 = 10330 AdvReadEEPWord(iop_base, ADV_EEP_DVC_CFG_END - 2); 10331 10332 eep_config.serial_number_word1 = 10333 AdvReadEEPWord(iop_base, ADV_EEP_DVC_CFG_END - 3); 10334 10335 AdvSet38C0800EEPConfig(iop_base, &eep_config); 10336 } 10337 /* 10338 * Set ADV_DVC_VAR and ADV_DVC_CFG variables from the 10339 * EEPROM configuration that was read. 10340 * 10341 * This is the mapping of EEPROM fields to Adv Library fields. 10342 */ 10343 asc_dvc->wdtr_able = eep_config.wdtr_able; 10344 asc_dvc->sdtr_speed1 = eep_config.sdtr_speed1; 10345 asc_dvc->sdtr_speed2 = eep_config.sdtr_speed2; 10346 asc_dvc->sdtr_speed3 = eep_config.sdtr_speed3; 10347 asc_dvc->sdtr_speed4 = eep_config.sdtr_speed4; 10348 asc_dvc->tagqng_able = eep_config.tagqng_able; 10349 asc_dvc->cfg->disc_enable = eep_config.disc_enable; 10350 asc_dvc->max_host_qng = eep_config.max_host_qng; 10351 asc_dvc->max_dvc_qng = eep_config.max_dvc_qng; 10352 asc_dvc->chip_scsi_id = (eep_config.adapter_scsi_id & ADV_MAX_TID); 10353 asc_dvc->start_motor = eep_config.start_motor; 10354 asc_dvc->scsi_reset_wait = eep_config.scsi_reset_delay; 10355 asc_dvc->bios_ctrl = eep_config.bios_ctrl; 10356 asc_dvc->no_scam = eep_config.scam_tolerant; 10357 asc_dvc->cfg->serial1 = eep_config.serial_number_word1; 10358 asc_dvc->cfg->serial2 = eep_config.serial_number_word2; 10359 asc_dvc->cfg->serial3 = eep_config.serial_number_word3; 10360 10361 /* 10362 * For every Target ID if any of its 'sdtr_speed[1234]' bits 10363 * are set, then set an 'sdtr_able' bit for it. 10364 */ 10365 asc_dvc->sdtr_able = 0; 10366 for (tid = 0; tid <= ADV_MAX_TID; tid++) { 10367 if (tid == 0) { 10368 sdtr_speed = asc_dvc->sdtr_speed1; 10369 } else if (tid == 4) { 10370 sdtr_speed = asc_dvc->sdtr_speed2; 10371 } else if (tid == 8) { 10372 sdtr_speed = asc_dvc->sdtr_speed3; 10373 } else if (tid == 12) { 10374 sdtr_speed = asc_dvc->sdtr_speed4; 10375 } 10376 if (sdtr_speed & ADV_MAX_TID) { 10377 asc_dvc->sdtr_able |= (1 << tid); 10378 } 10379 sdtr_speed >>= 4; 10380 } 10381 10382 /* 10383 * Set the host maximum queuing (max. 253, min. 16) and the per device 10384 * maximum queuing (max. 63, min. 4). 10385 */ 10386 if (eep_config.max_host_qng > ASC_DEF_MAX_HOST_QNG) { 10387 eep_config.max_host_qng = ASC_DEF_MAX_HOST_QNG; 10388 } else if (eep_config.max_host_qng < ASC_DEF_MIN_HOST_QNG) { 10389 /* If the value is zero, assume it is uninitialized. */ 10390 if (eep_config.max_host_qng == 0) { 10391 eep_config.max_host_qng = ASC_DEF_MAX_HOST_QNG; 10392 } else { 10393 eep_config.max_host_qng = ASC_DEF_MIN_HOST_QNG; 10394 } 10395 } 10396 10397 if (eep_config.max_dvc_qng > ASC_DEF_MAX_DVC_QNG) { 10398 eep_config.max_dvc_qng = ASC_DEF_MAX_DVC_QNG; 10399 } else if (eep_config.max_dvc_qng < ASC_DEF_MIN_DVC_QNG) { 10400 /* If the value is zero, assume it is uninitialized. */ 10401 if (eep_config.max_dvc_qng == 0) { 10402 eep_config.max_dvc_qng = ASC_DEF_MAX_DVC_QNG; 10403 } else { 10404 eep_config.max_dvc_qng = ASC_DEF_MIN_DVC_QNG; 10405 } 10406 } 10407 10408 /* 10409 * If 'max_dvc_qng' is greater than 'max_host_qng', then 10410 * set 'max_dvc_qng' to 'max_host_qng'. 10411 */ 10412 if (eep_config.max_dvc_qng > eep_config.max_host_qng) { 10413 eep_config.max_dvc_qng = eep_config.max_host_qng; 10414 } 10415 10416 /* 10417 * Set ADV_DVC_VAR 'max_host_qng' and ADV_DVC_VAR 'max_dvc_qng' 10418 * values based on possibly adjusted EEPROM values. 10419 */ 10420 asc_dvc->max_host_qng = eep_config.max_host_qng; 10421 asc_dvc->max_dvc_qng = eep_config.max_dvc_qng; 10422 10423 /* 10424 * If the EEPROM 'termination' field is set to automatic (0), then set 10425 * the ADV_DVC_CFG 'termination' field to automatic also. 10426 * 10427 * If the termination is specified with a non-zero 'termination' 10428 * value check that a legal value is set and set the ADV_DVC_CFG 10429 * 'termination' field appropriately. 10430 */ 10431 if (eep_config.termination_se == 0) { 10432 termination = 0; /* auto termination for SE */ 10433 } else { 10434 /* Enable manual control with low off / high off. */ 10435 if (eep_config.termination_se == 1) { 10436 termination = 0; 10437 10438 /* Enable manual control with low off / high on. */ 10439 } else if (eep_config.termination_se == 2) { 10440 termination = TERM_SE_HI; 10441 10442 /* Enable manual control with low on / high on. */ 10443 } else if (eep_config.termination_se == 3) { 10444 termination = TERM_SE; 10445 } else { 10446 /* 10447 * The EEPROM 'termination_se' field contains a bad value. 10448 * Use automatic termination instead. 10449 */ 10450 termination = 0; 10451 warn_code |= ASC_WARN_EEPROM_TERMINATION; 10452 } 10453 } 10454 10455 if (eep_config.termination_lvd == 0) { 10456 asc_dvc->cfg->termination = termination; /* auto termination for LVD */ 10457 } else { 10458 /* Enable manual control with low off / high off. */ 10459 if (eep_config.termination_lvd == 1) { 10460 asc_dvc->cfg->termination = termination; 10461 10462 /* Enable manual control with low off / high on. */ 10463 } else if (eep_config.termination_lvd == 2) { 10464 asc_dvc->cfg->termination = termination | TERM_LVD_HI; 10465 10466 /* Enable manual control with low on / high on. */ 10467 } else if (eep_config.termination_lvd == 3) { 10468 asc_dvc->cfg->termination = termination | TERM_LVD; 10469 } else { 10470 /* 10471 * The EEPROM 'termination_lvd' field contains a bad value. 10472 * Use automatic termination instead. 10473 */ 10474 asc_dvc->cfg->termination = termination; 10475 warn_code |= ASC_WARN_EEPROM_TERMINATION; 10476 } 10477 } 10478 10479 return warn_code; 10480 } 10481 10482 /* 10483 * Read the board's EEPROM configuration. Set fields in ASC_DVC_VAR and 10484 * ASC_DVC_CFG based on the EEPROM settings. The chip is stopped while 10485 * all of this is done. 10486 * 10487 * On failure set the ASC_DVC_VAR field 'err_code' and return ADV_ERROR. 10488 * 10489 * For a non-fatal error return a warning code. If there are no warnings 10490 * then 0 is returned. 10491 * 10492 * Note: Chip is stopped on entry. 10493 */ 10494 static int AdvInitFrom38C1600EEP(ADV_DVC_VAR *asc_dvc) 10495 { 10496 AdvPortAddr iop_base; 10497 ushort warn_code; 10498 ADVEEP_38C1600_CONFIG eep_config; 10499 uchar tid, termination; 10500 ushort sdtr_speed = 0; 10501 10502 iop_base = asc_dvc->iop_base; 10503 10504 warn_code = 0; 10505 10506 /* 10507 * Read the board's EEPROM configuration. 10508 * 10509 * Set default values if a bad checksum is found. 10510 */ 10511 if (AdvGet38C1600EEPConfig(iop_base, &eep_config) != 10512 eep_config.check_sum) { 10513 struct pci_dev *pdev = adv_dvc_to_pdev(asc_dvc); 10514 warn_code |= ASC_WARN_EEPROM_CHKSUM; 10515 10516 /* 10517 * Set EEPROM default values. 10518 */ 10519 memcpy(&eep_config, &Default_38C1600_EEPROM_Config, 10520 sizeof(ADVEEP_38C1600_CONFIG)); 10521 10522 if (PCI_FUNC(pdev->devfn) != 0) { 10523 u8 ints; 10524 /* 10525 * Disable Bit 14 (BIOS_ENABLE) to fix SPARC Ultra 60 10526 * and old Mac system booting problem. The Expansion 10527 * ROM must be disabled in Function 1 for these systems 10528 */ 10529 eep_config.cfg_lsw &= ~ADV_EEPROM_BIOS_ENABLE; 10530 /* 10531 * Clear the INTAB (bit 11) if the GPIO 0 input 10532 * indicates the Function 1 interrupt line is wired 10533 * to INTB. 10534 * 10535 * Set/Clear Bit 11 (INTAB) from the GPIO bit 0 input: 10536 * 1 - Function 1 interrupt line wired to INT A. 10537 * 0 - Function 1 interrupt line wired to INT B. 10538 * 10539 * Note: Function 0 is always wired to INTA. 10540 * Put all 5 GPIO bits in input mode and then read 10541 * their input values. 10542 */ 10543 AdvWriteByteRegister(iop_base, IOPB_GPIO_CNTL, 0); 10544 ints = AdvReadByteRegister(iop_base, IOPB_GPIO_DATA); 10545 if ((ints & 0x01) == 0) 10546 eep_config.cfg_lsw &= ~ADV_EEPROM_INTAB; 10547 } 10548 10549 /* 10550 * Assume the 6 byte board serial number that was read from 10551 * EEPROM is correct even if the EEPROM checksum failed. 10552 */ 10553 eep_config.serial_number_word3 = 10554 AdvReadEEPWord(iop_base, ADV_EEP_DVC_CFG_END - 1); 10555 eep_config.serial_number_word2 = 10556 AdvReadEEPWord(iop_base, ADV_EEP_DVC_CFG_END - 2); 10557 eep_config.serial_number_word1 = 10558 AdvReadEEPWord(iop_base, ADV_EEP_DVC_CFG_END - 3); 10559 10560 AdvSet38C1600EEPConfig(iop_base, &eep_config); 10561 } 10562 10563 /* 10564 * Set ASC_DVC_VAR and ASC_DVC_CFG variables from the 10565 * EEPROM configuration that was read. 10566 * 10567 * This is the mapping of EEPROM fields to Adv Library fields. 10568 */ 10569 asc_dvc->wdtr_able = eep_config.wdtr_able; 10570 asc_dvc->sdtr_speed1 = eep_config.sdtr_speed1; 10571 asc_dvc->sdtr_speed2 = eep_config.sdtr_speed2; 10572 asc_dvc->sdtr_speed3 = eep_config.sdtr_speed3; 10573 asc_dvc->sdtr_speed4 = eep_config.sdtr_speed4; 10574 asc_dvc->ppr_able = 0; 10575 asc_dvc->tagqng_able = eep_config.tagqng_able; 10576 asc_dvc->cfg->disc_enable = eep_config.disc_enable; 10577 asc_dvc->max_host_qng = eep_config.max_host_qng; 10578 asc_dvc->max_dvc_qng = eep_config.max_dvc_qng; 10579 asc_dvc->chip_scsi_id = (eep_config.adapter_scsi_id & ASC_MAX_TID); 10580 asc_dvc->start_motor = eep_config.start_motor; 10581 asc_dvc->scsi_reset_wait = eep_config.scsi_reset_delay; 10582 asc_dvc->bios_ctrl = eep_config.bios_ctrl; 10583 asc_dvc->no_scam = eep_config.scam_tolerant; 10584 10585 /* 10586 * For every Target ID if any of its 'sdtr_speed[1234]' bits 10587 * are set, then set an 'sdtr_able' bit for it. 10588 */ 10589 asc_dvc->sdtr_able = 0; 10590 for (tid = 0; tid <= ASC_MAX_TID; tid++) { 10591 if (tid == 0) { 10592 sdtr_speed = asc_dvc->sdtr_speed1; 10593 } else if (tid == 4) { 10594 sdtr_speed = asc_dvc->sdtr_speed2; 10595 } else if (tid == 8) { 10596 sdtr_speed = asc_dvc->sdtr_speed3; 10597 } else if (tid == 12) { 10598 sdtr_speed = asc_dvc->sdtr_speed4; 10599 } 10600 if (sdtr_speed & ASC_MAX_TID) { 10601 asc_dvc->sdtr_able |= (1 << tid); 10602 } 10603 sdtr_speed >>= 4; 10604 } 10605 10606 /* 10607 * Set the host maximum queuing (max. 253, min. 16) and the per device 10608 * maximum queuing (max. 63, min. 4). 10609 */ 10610 if (eep_config.max_host_qng > ASC_DEF_MAX_HOST_QNG) { 10611 eep_config.max_host_qng = ASC_DEF_MAX_HOST_QNG; 10612 } else if (eep_config.max_host_qng < ASC_DEF_MIN_HOST_QNG) { 10613 /* If the value is zero, assume it is uninitialized. */ 10614 if (eep_config.max_host_qng == 0) { 10615 eep_config.max_host_qng = ASC_DEF_MAX_HOST_QNG; 10616 } else { 10617 eep_config.max_host_qng = ASC_DEF_MIN_HOST_QNG; 10618 } 10619 } 10620 10621 if (eep_config.max_dvc_qng > ASC_DEF_MAX_DVC_QNG) { 10622 eep_config.max_dvc_qng = ASC_DEF_MAX_DVC_QNG; 10623 } else if (eep_config.max_dvc_qng < ASC_DEF_MIN_DVC_QNG) { 10624 /* If the value is zero, assume it is uninitialized. */ 10625 if (eep_config.max_dvc_qng == 0) { 10626 eep_config.max_dvc_qng = ASC_DEF_MAX_DVC_QNG; 10627 } else { 10628 eep_config.max_dvc_qng = ASC_DEF_MIN_DVC_QNG; 10629 } 10630 } 10631 10632 /* 10633 * If 'max_dvc_qng' is greater than 'max_host_qng', then 10634 * set 'max_dvc_qng' to 'max_host_qng'. 10635 */ 10636 if (eep_config.max_dvc_qng > eep_config.max_host_qng) { 10637 eep_config.max_dvc_qng = eep_config.max_host_qng; 10638 } 10639 10640 /* 10641 * Set ASC_DVC_VAR 'max_host_qng' and ASC_DVC_VAR 'max_dvc_qng' 10642 * values based on possibly adjusted EEPROM values. 10643 */ 10644 asc_dvc->max_host_qng = eep_config.max_host_qng; 10645 asc_dvc->max_dvc_qng = eep_config.max_dvc_qng; 10646 10647 /* 10648 * If the EEPROM 'termination' field is set to automatic (0), then set 10649 * the ASC_DVC_CFG 'termination' field to automatic also. 10650 * 10651 * If the termination is specified with a non-zero 'termination' 10652 * value check that a legal value is set and set the ASC_DVC_CFG 10653 * 'termination' field appropriately. 10654 */ 10655 if (eep_config.termination_se == 0) { 10656 termination = 0; /* auto termination for SE */ 10657 } else { 10658 /* Enable manual control with low off / high off. */ 10659 if (eep_config.termination_se == 1) { 10660 termination = 0; 10661 10662 /* Enable manual control with low off / high on. */ 10663 } else if (eep_config.termination_se == 2) { 10664 termination = TERM_SE_HI; 10665 10666 /* Enable manual control with low on / high on. */ 10667 } else if (eep_config.termination_se == 3) { 10668 termination = TERM_SE; 10669 } else { 10670 /* 10671 * The EEPROM 'termination_se' field contains a bad value. 10672 * Use automatic termination instead. 10673 */ 10674 termination = 0; 10675 warn_code |= ASC_WARN_EEPROM_TERMINATION; 10676 } 10677 } 10678 10679 if (eep_config.termination_lvd == 0) { 10680 asc_dvc->cfg->termination = termination; /* auto termination for LVD */ 10681 } else { 10682 /* Enable manual control with low off / high off. */ 10683 if (eep_config.termination_lvd == 1) { 10684 asc_dvc->cfg->termination = termination; 10685 10686 /* Enable manual control with low off / high on. */ 10687 } else if (eep_config.termination_lvd == 2) { 10688 asc_dvc->cfg->termination = termination | TERM_LVD_HI; 10689 10690 /* Enable manual control with low on / high on. */ 10691 } else if (eep_config.termination_lvd == 3) { 10692 asc_dvc->cfg->termination = termination | TERM_LVD; 10693 } else { 10694 /* 10695 * The EEPROM 'termination_lvd' field contains a bad value. 10696 * Use automatic termination instead. 10697 */ 10698 asc_dvc->cfg->termination = termination; 10699 warn_code |= ASC_WARN_EEPROM_TERMINATION; 10700 } 10701 } 10702 10703 return warn_code; 10704 } 10705 10706 /* 10707 * Initialize the ADV_DVC_VAR structure. 10708 * 10709 * On failure set the ADV_DVC_VAR field 'err_code' and return ADV_ERROR. 10710 * 10711 * For a non-fatal error return a warning code. If there are no warnings 10712 * then 0 is returned. 10713 */ 10714 static int AdvInitGetConfig(struct pci_dev *pdev, struct Scsi_Host *shost) 10715 { 10716 struct asc_board *board = shost_priv(shost); 10717 ADV_DVC_VAR *asc_dvc = &board->dvc_var.adv_dvc_var; 10718 unsigned short warn_code = 0; 10719 AdvPortAddr iop_base = asc_dvc->iop_base; 10720 u16 cmd; 10721 int status; 10722 10723 asc_dvc->err_code = 0; 10724 10725 /* 10726 * Save the state of the PCI Configuration Command Register 10727 * "Parity Error Response Control" Bit. If the bit is clear (0), 10728 * in AdvInitAsc3550/38C0800Driver() tell the microcode to ignore 10729 * DMA parity errors. 10730 */ 10731 asc_dvc->cfg->control_flag = 0; 10732 pci_read_config_word(pdev, PCI_COMMAND, &cmd); 10733 if ((cmd & PCI_COMMAND_PARITY) == 0) 10734 asc_dvc->cfg->control_flag |= CONTROL_FLAG_IGNORE_PERR; 10735 10736 asc_dvc->cfg->chip_version = 10737 AdvGetChipVersion(iop_base, asc_dvc->bus_type); 10738 10739 ASC_DBG(1, "iopb_chip_id_1: 0x%x 0x%x\n", 10740 (ushort)AdvReadByteRegister(iop_base, IOPB_CHIP_ID_1), 10741 (ushort)ADV_CHIP_ID_BYTE); 10742 10743 ASC_DBG(1, "iopw_chip_id_0: 0x%x 0x%x\n", 10744 (ushort)AdvReadWordRegister(iop_base, IOPW_CHIP_ID_0), 10745 (ushort)ADV_CHIP_ID_WORD); 10746 10747 /* 10748 * Reset the chip to start and allow register writes. 10749 */ 10750 if (AdvFindSignature(iop_base) == 0) { 10751 asc_dvc->err_code = ASC_IERR_BAD_SIGNATURE; 10752 return ADV_ERROR; 10753 } else { 10754 /* 10755 * The caller must set 'chip_type' to a valid setting. 10756 */ 10757 if (asc_dvc->chip_type != ADV_CHIP_ASC3550 && 10758 asc_dvc->chip_type != ADV_CHIP_ASC38C0800 && 10759 asc_dvc->chip_type != ADV_CHIP_ASC38C1600) { 10760 asc_dvc->err_code |= ASC_IERR_BAD_CHIPTYPE; 10761 return ADV_ERROR; 10762 } 10763 10764 /* 10765 * Reset Chip. 10766 */ 10767 AdvWriteWordRegister(iop_base, IOPW_CTRL_REG, 10768 ADV_CTRL_REG_CMD_RESET); 10769 mdelay(100); 10770 AdvWriteWordRegister(iop_base, IOPW_CTRL_REG, 10771 ADV_CTRL_REG_CMD_WR_IO_REG); 10772 10773 if (asc_dvc->chip_type == ADV_CHIP_ASC38C1600) { 10774 status = AdvInitFrom38C1600EEP(asc_dvc); 10775 } else if (asc_dvc->chip_type == ADV_CHIP_ASC38C0800) { 10776 status = AdvInitFrom38C0800EEP(asc_dvc); 10777 } else { 10778 status = AdvInitFrom3550EEP(asc_dvc); 10779 } 10780 warn_code |= status; 10781 } 10782 10783 if (warn_code != 0) 10784 shost_printk(KERN_WARNING, shost, "warning: 0x%x\n", warn_code); 10785 10786 if (asc_dvc->err_code) 10787 shost_printk(KERN_ERR, shost, "error code 0x%x\n", 10788 asc_dvc->err_code); 10789 10790 return asc_dvc->err_code; 10791 } 10792 #endif 10793 10794 static struct scsi_host_template advansys_template = { 10795 .proc_name = DRV_NAME, 10796 #ifdef CONFIG_PROC_FS 10797 .show_info = advansys_show_info, 10798 #endif 10799 .name = DRV_NAME, 10800 .info = advansys_info, 10801 .queuecommand = advansys_queuecommand, 10802 .eh_host_reset_handler = advansys_reset, 10803 .bios_param = advansys_biosparam, 10804 .slave_configure = advansys_slave_configure, 10805 /* 10806 * Because the driver may control an ISA adapter 'unchecked_isa_dma' 10807 * must be set. The flag will be cleared in advansys_board_found 10808 * for non-ISA adapters. 10809 */ 10810 .unchecked_isa_dma = true, 10811 /* 10812 * All adapters controlled by this driver are capable of large 10813 * scatter-gather lists. According to the mid-level SCSI documentation 10814 * this obviates any performance gain provided by setting 10815 * 'use_clustering'. But empirically while CPU utilization is increased 10816 * by enabling clustering, I/O throughput increases as well. 10817 */ 10818 .use_clustering = ENABLE_CLUSTERING, 10819 }; 10820 10821 static int advansys_wide_init_chip(struct Scsi_Host *shost) 10822 { 10823 struct asc_board *board = shost_priv(shost); 10824 struct adv_dvc_var *adv_dvc = &board->dvc_var.adv_dvc_var; 10825 size_t sgblk_pool_size; 10826 int warn_code, err_code; 10827 10828 /* 10829 * Allocate buffer carrier structures. The total size 10830 * is about 8 KB, so allocate all at once. 10831 */ 10832 adv_dvc->carrier = dma_alloc_coherent(board->dev, 10833 ADV_CARRIER_BUFSIZE, &adv_dvc->carrier_addr, GFP_KERNEL); 10834 ASC_DBG(1, "carrier 0x%p\n", adv_dvc->carrier); 10835 10836 if (!adv_dvc->carrier) 10837 goto kmalloc_failed; 10838 10839 /* 10840 * Allocate up to 'max_host_qng' request structures for the Wide 10841 * board. The total size is about 16 KB, so allocate all at once. 10842 * If the allocation fails decrement and try again. 10843 */ 10844 board->adv_reqp_size = adv_dvc->max_host_qng * sizeof(adv_req_t); 10845 if (board->adv_reqp_size & 0x1f) { 10846 ASC_DBG(1, "unaligned reqp %lu bytes\n", sizeof(adv_req_t)); 10847 board->adv_reqp_size = ADV_32BALIGN(board->adv_reqp_size); 10848 } 10849 board->adv_reqp = dma_alloc_coherent(board->dev, board->adv_reqp_size, 10850 &board->adv_reqp_addr, GFP_KERNEL); 10851 10852 if (!board->adv_reqp) 10853 goto kmalloc_failed; 10854 10855 ASC_DBG(1, "reqp 0x%p, req_cnt %d, bytes %lu\n", board->adv_reqp, 10856 adv_dvc->max_host_qng, board->adv_reqp_size); 10857 10858 /* 10859 * Allocate up to ADV_TOT_SG_BLOCK request structures for 10860 * the Wide board. Each structure is about 136 bytes. 10861 */ 10862 sgblk_pool_size = sizeof(adv_sgblk_t) * ADV_TOT_SG_BLOCK; 10863 board->adv_sgblk_pool = dma_pool_create("adv_sgblk", board->dev, 10864 sgblk_pool_size, 32, 0); 10865 10866 ASC_DBG(1, "sg_cnt %d * %lu = %lu bytes\n", ADV_TOT_SG_BLOCK, 10867 sizeof(adv_sgblk_t), sgblk_pool_size); 10868 10869 if (!board->adv_sgblk_pool) 10870 goto kmalloc_failed; 10871 10872 if (adv_dvc->chip_type == ADV_CHIP_ASC3550) { 10873 ASC_DBG(2, "AdvInitAsc3550Driver()\n"); 10874 warn_code = AdvInitAsc3550Driver(adv_dvc); 10875 } else if (adv_dvc->chip_type == ADV_CHIP_ASC38C0800) { 10876 ASC_DBG(2, "AdvInitAsc38C0800Driver()\n"); 10877 warn_code = AdvInitAsc38C0800Driver(adv_dvc); 10878 } else { 10879 ASC_DBG(2, "AdvInitAsc38C1600Driver()\n"); 10880 warn_code = AdvInitAsc38C1600Driver(adv_dvc); 10881 } 10882 err_code = adv_dvc->err_code; 10883 10884 if (warn_code || err_code) { 10885 shost_printk(KERN_WARNING, shost, "error: warn 0x%x, error " 10886 "0x%x\n", warn_code, err_code); 10887 } 10888 10889 goto exit; 10890 10891 kmalloc_failed: 10892 shost_printk(KERN_ERR, shost, "error: kmalloc() failed\n"); 10893 err_code = ADV_ERROR; 10894 exit: 10895 return err_code; 10896 } 10897 10898 static void advansys_wide_free_mem(struct asc_board *board) 10899 { 10900 struct adv_dvc_var *adv_dvc = &board->dvc_var.adv_dvc_var; 10901 10902 if (adv_dvc->carrier) { 10903 dma_free_coherent(board->dev, ADV_CARRIER_BUFSIZE, 10904 adv_dvc->carrier, adv_dvc->carrier_addr); 10905 adv_dvc->carrier = NULL; 10906 } 10907 if (board->adv_reqp) { 10908 dma_free_coherent(board->dev, board->adv_reqp_size, 10909 board->adv_reqp, board->adv_reqp_addr); 10910 board->adv_reqp = NULL; 10911 } 10912 if (board->adv_sgblk_pool) { 10913 dma_pool_destroy(board->adv_sgblk_pool); 10914 board->adv_sgblk_pool = NULL; 10915 } 10916 } 10917 10918 static int advansys_board_found(struct Scsi_Host *shost, unsigned int iop, 10919 int bus_type) 10920 { 10921 struct pci_dev *pdev; 10922 struct asc_board *boardp = shost_priv(shost); 10923 ASC_DVC_VAR *asc_dvc_varp = NULL; 10924 ADV_DVC_VAR *adv_dvc_varp = NULL; 10925 int share_irq, warn_code, ret; 10926 10927 pdev = (bus_type == ASC_IS_PCI) ? to_pci_dev(boardp->dev) : NULL; 10928 10929 if (ASC_NARROW_BOARD(boardp)) { 10930 ASC_DBG(1, "narrow board\n"); 10931 asc_dvc_varp = &boardp->dvc_var.asc_dvc_var; 10932 asc_dvc_varp->bus_type = bus_type; 10933 asc_dvc_varp->drv_ptr = boardp; 10934 asc_dvc_varp->cfg = &boardp->dvc_cfg.asc_dvc_cfg; 10935 asc_dvc_varp->iop_base = iop; 10936 } else { 10937 #ifdef CONFIG_PCI 10938 adv_dvc_varp = &boardp->dvc_var.adv_dvc_var; 10939 adv_dvc_varp->drv_ptr = boardp; 10940 adv_dvc_varp->cfg = &boardp->dvc_cfg.adv_dvc_cfg; 10941 if (pdev->device == PCI_DEVICE_ID_ASP_ABP940UW) { 10942 ASC_DBG(1, "wide board ASC-3550\n"); 10943 adv_dvc_varp->chip_type = ADV_CHIP_ASC3550; 10944 } else if (pdev->device == PCI_DEVICE_ID_38C0800_REV1) { 10945 ASC_DBG(1, "wide board ASC-38C0800\n"); 10946 adv_dvc_varp->chip_type = ADV_CHIP_ASC38C0800; 10947 } else { 10948 ASC_DBG(1, "wide board ASC-38C1600\n"); 10949 adv_dvc_varp->chip_type = ADV_CHIP_ASC38C1600; 10950 } 10951 10952 boardp->asc_n_io_port = pci_resource_len(pdev, 1); 10953 boardp->ioremap_addr = pci_ioremap_bar(pdev, 1); 10954 if (!boardp->ioremap_addr) { 10955 shost_printk(KERN_ERR, shost, "ioremap(%lx, %d) " 10956 "returned NULL\n", 10957 (long)pci_resource_start(pdev, 1), 10958 boardp->asc_n_io_port); 10959 ret = -ENODEV; 10960 goto err_shost; 10961 } 10962 adv_dvc_varp->iop_base = (AdvPortAddr)boardp->ioremap_addr; 10963 ASC_DBG(1, "iop_base: 0x%p\n", adv_dvc_varp->iop_base); 10964 10965 /* 10966 * Even though it isn't used to access wide boards, other 10967 * than for the debug line below, save I/O Port address so 10968 * that it can be reported. 10969 */ 10970 boardp->ioport = iop; 10971 10972 ASC_DBG(1, "iopb_chip_id_1 0x%x, iopw_chip_id_0 0x%x\n", 10973 (ushort)inp(iop + 1), (ushort)inpw(iop)); 10974 #endif /* CONFIG_PCI */ 10975 } 10976 10977 if (ASC_NARROW_BOARD(boardp)) { 10978 /* 10979 * Set the board bus type and PCI IRQ before 10980 * calling AscInitGetConfig(). 10981 */ 10982 switch (asc_dvc_varp->bus_type) { 10983 #ifdef CONFIG_ISA 10984 case ASC_IS_ISA: 10985 shost->unchecked_isa_dma = true; 10986 share_irq = 0; 10987 break; 10988 case ASC_IS_VL: 10989 shost->unchecked_isa_dma = false; 10990 share_irq = 0; 10991 break; 10992 case ASC_IS_EISA: 10993 shost->unchecked_isa_dma = false; 10994 share_irq = IRQF_SHARED; 10995 break; 10996 #endif /* CONFIG_ISA */ 10997 #ifdef CONFIG_PCI 10998 case ASC_IS_PCI: 10999 shost->unchecked_isa_dma = false; 11000 share_irq = IRQF_SHARED; 11001 break; 11002 #endif /* CONFIG_PCI */ 11003 default: 11004 shost_printk(KERN_ERR, shost, "unknown adapter type: " 11005 "%d\n", asc_dvc_varp->bus_type); 11006 shost->unchecked_isa_dma = false; 11007 share_irq = 0; 11008 break; 11009 } 11010 11011 /* 11012 * NOTE: AscInitGetConfig() may change the board's 11013 * bus_type value. The bus_type value should no 11014 * longer be used. If the bus_type field must be 11015 * referenced only use the bit-wise AND operator "&". 11016 */ 11017 ASC_DBG(2, "AscInitGetConfig()\n"); 11018 ret = AscInitGetConfig(shost) ? -ENODEV : 0; 11019 } else { 11020 #ifdef CONFIG_PCI 11021 /* 11022 * For Wide boards set PCI information before calling 11023 * AdvInitGetConfig(). 11024 */ 11025 shost->unchecked_isa_dma = false; 11026 share_irq = IRQF_SHARED; 11027 ASC_DBG(2, "AdvInitGetConfig()\n"); 11028 11029 ret = AdvInitGetConfig(pdev, shost) ? -ENODEV : 0; 11030 #else 11031 share_irq = 0; 11032 ret = -ENODEV; 11033 #endif /* CONFIG_PCI */ 11034 } 11035 11036 if (ret) 11037 goto err_unmap; 11038 11039 /* 11040 * Save the EEPROM configuration so that it can be displayed 11041 * from /proc/scsi/advansys/[0...]. 11042 */ 11043 if (ASC_NARROW_BOARD(boardp)) { 11044 11045 ASCEEP_CONFIG *ep; 11046 11047 /* 11048 * Set the adapter's target id bit in the 'init_tidmask' field. 11049 */ 11050 boardp->init_tidmask |= 11051 ADV_TID_TO_TIDMASK(asc_dvc_varp->cfg->chip_scsi_id); 11052 11053 /* 11054 * Save EEPROM settings for the board. 11055 */ 11056 ep = &boardp->eep_config.asc_eep; 11057 11058 ep->init_sdtr = asc_dvc_varp->cfg->sdtr_enable; 11059 ep->disc_enable = asc_dvc_varp->cfg->disc_enable; 11060 ep->use_cmd_qng = asc_dvc_varp->cfg->cmd_qng_enabled; 11061 ASC_EEP_SET_DMA_SPD(ep, asc_dvc_varp->cfg->isa_dma_speed); 11062 ep->start_motor = asc_dvc_varp->start_motor; 11063 ep->cntl = asc_dvc_varp->dvc_cntl; 11064 ep->no_scam = asc_dvc_varp->no_scam; 11065 ep->max_total_qng = asc_dvc_varp->max_total_qng; 11066 ASC_EEP_SET_CHIP_ID(ep, asc_dvc_varp->cfg->chip_scsi_id); 11067 /* 'max_tag_qng' is set to the same value for every device. */ 11068 ep->max_tag_qng = asc_dvc_varp->cfg->max_tag_qng[0]; 11069 ep->adapter_info[0] = asc_dvc_varp->cfg->adapter_info[0]; 11070 ep->adapter_info[1] = asc_dvc_varp->cfg->adapter_info[1]; 11071 ep->adapter_info[2] = asc_dvc_varp->cfg->adapter_info[2]; 11072 ep->adapter_info[3] = asc_dvc_varp->cfg->adapter_info[3]; 11073 ep->adapter_info[4] = asc_dvc_varp->cfg->adapter_info[4]; 11074 ep->adapter_info[5] = asc_dvc_varp->cfg->adapter_info[5]; 11075 11076 /* 11077 * Modify board configuration. 11078 */ 11079 ASC_DBG(2, "AscInitSetConfig()\n"); 11080 ret = AscInitSetConfig(pdev, shost) ? -ENODEV : 0; 11081 if (ret) 11082 goto err_unmap; 11083 } else { 11084 ADVEEP_3550_CONFIG *ep_3550; 11085 ADVEEP_38C0800_CONFIG *ep_38C0800; 11086 ADVEEP_38C1600_CONFIG *ep_38C1600; 11087 11088 /* 11089 * Save Wide EEP Configuration Information. 11090 */ 11091 if (adv_dvc_varp->chip_type == ADV_CHIP_ASC3550) { 11092 ep_3550 = &boardp->eep_config.adv_3550_eep; 11093 11094 ep_3550->adapter_scsi_id = adv_dvc_varp->chip_scsi_id; 11095 ep_3550->max_host_qng = adv_dvc_varp->max_host_qng; 11096 ep_3550->max_dvc_qng = adv_dvc_varp->max_dvc_qng; 11097 ep_3550->termination = adv_dvc_varp->cfg->termination; 11098 ep_3550->disc_enable = adv_dvc_varp->cfg->disc_enable; 11099 ep_3550->bios_ctrl = adv_dvc_varp->bios_ctrl; 11100 ep_3550->wdtr_able = adv_dvc_varp->wdtr_able; 11101 ep_3550->sdtr_able = adv_dvc_varp->sdtr_able; 11102 ep_3550->ultra_able = adv_dvc_varp->ultra_able; 11103 ep_3550->tagqng_able = adv_dvc_varp->tagqng_able; 11104 ep_3550->start_motor = adv_dvc_varp->start_motor; 11105 ep_3550->scsi_reset_delay = 11106 adv_dvc_varp->scsi_reset_wait; 11107 ep_3550->serial_number_word1 = 11108 adv_dvc_varp->cfg->serial1; 11109 ep_3550->serial_number_word2 = 11110 adv_dvc_varp->cfg->serial2; 11111 ep_3550->serial_number_word3 = 11112 adv_dvc_varp->cfg->serial3; 11113 } else if (adv_dvc_varp->chip_type == ADV_CHIP_ASC38C0800) { 11114 ep_38C0800 = &boardp->eep_config.adv_38C0800_eep; 11115 11116 ep_38C0800->adapter_scsi_id = 11117 adv_dvc_varp->chip_scsi_id; 11118 ep_38C0800->max_host_qng = adv_dvc_varp->max_host_qng; 11119 ep_38C0800->max_dvc_qng = adv_dvc_varp->max_dvc_qng; 11120 ep_38C0800->termination_lvd = 11121 adv_dvc_varp->cfg->termination; 11122 ep_38C0800->disc_enable = 11123 adv_dvc_varp->cfg->disc_enable; 11124 ep_38C0800->bios_ctrl = adv_dvc_varp->bios_ctrl; 11125 ep_38C0800->wdtr_able = adv_dvc_varp->wdtr_able; 11126 ep_38C0800->tagqng_able = adv_dvc_varp->tagqng_able; 11127 ep_38C0800->sdtr_speed1 = adv_dvc_varp->sdtr_speed1; 11128 ep_38C0800->sdtr_speed2 = adv_dvc_varp->sdtr_speed2; 11129 ep_38C0800->sdtr_speed3 = adv_dvc_varp->sdtr_speed3; 11130 ep_38C0800->sdtr_speed4 = adv_dvc_varp->sdtr_speed4; 11131 ep_38C0800->tagqng_able = adv_dvc_varp->tagqng_able; 11132 ep_38C0800->start_motor = adv_dvc_varp->start_motor; 11133 ep_38C0800->scsi_reset_delay = 11134 adv_dvc_varp->scsi_reset_wait; 11135 ep_38C0800->serial_number_word1 = 11136 adv_dvc_varp->cfg->serial1; 11137 ep_38C0800->serial_number_word2 = 11138 adv_dvc_varp->cfg->serial2; 11139 ep_38C0800->serial_number_word3 = 11140 adv_dvc_varp->cfg->serial3; 11141 } else { 11142 ep_38C1600 = &boardp->eep_config.adv_38C1600_eep; 11143 11144 ep_38C1600->adapter_scsi_id = 11145 adv_dvc_varp->chip_scsi_id; 11146 ep_38C1600->max_host_qng = adv_dvc_varp->max_host_qng; 11147 ep_38C1600->max_dvc_qng = adv_dvc_varp->max_dvc_qng; 11148 ep_38C1600->termination_lvd = 11149 adv_dvc_varp->cfg->termination; 11150 ep_38C1600->disc_enable = 11151 adv_dvc_varp->cfg->disc_enable; 11152 ep_38C1600->bios_ctrl = adv_dvc_varp->bios_ctrl; 11153 ep_38C1600->wdtr_able = adv_dvc_varp->wdtr_able; 11154 ep_38C1600->tagqng_able = adv_dvc_varp->tagqng_able; 11155 ep_38C1600->sdtr_speed1 = adv_dvc_varp->sdtr_speed1; 11156 ep_38C1600->sdtr_speed2 = adv_dvc_varp->sdtr_speed2; 11157 ep_38C1600->sdtr_speed3 = adv_dvc_varp->sdtr_speed3; 11158 ep_38C1600->sdtr_speed4 = adv_dvc_varp->sdtr_speed4; 11159 ep_38C1600->tagqng_able = adv_dvc_varp->tagqng_able; 11160 ep_38C1600->start_motor = adv_dvc_varp->start_motor; 11161 ep_38C1600->scsi_reset_delay = 11162 adv_dvc_varp->scsi_reset_wait; 11163 ep_38C1600->serial_number_word1 = 11164 adv_dvc_varp->cfg->serial1; 11165 ep_38C1600->serial_number_word2 = 11166 adv_dvc_varp->cfg->serial2; 11167 ep_38C1600->serial_number_word3 = 11168 adv_dvc_varp->cfg->serial3; 11169 } 11170 11171 /* 11172 * Set the adapter's target id bit in the 'init_tidmask' field. 11173 */ 11174 boardp->init_tidmask |= 11175 ADV_TID_TO_TIDMASK(adv_dvc_varp->chip_scsi_id); 11176 } 11177 11178 /* 11179 * Channels are numbered beginning with 0. For AdvanSys one host 11180 * structure supports one channel. Multi-channel boards have a 11181 * separate host structure for each channel. 11182 */ 11183 shost->max_channel = 0; 11184 if (ASC_NARROW_BOARD(boardp)) { 11185 shost->max_id = ASC_MAX_TID + 1; 11186 shost->max_lun = ASC_MAX_LUN + 1; 11187 shost->max_cmd_len = ASC_MAX_CDB_LEN; 11188 11189 shost->io_port = asc_dvc_varp->iop_base; 11190 boardp->asc_n_io_port = ASC_IOADR_GAP; 11191 shost->this_id = asc_dvc_varp->cfg->chip_scsi_id; 11192 11193 /* Set maximum number of queues the adapter can handle. */ 11194 shost->can_queue = asc_dvc_varp->max_total_qng; 11195 } else { 11196 shost->max_id = ADV_MAX_TID + 1; 11197 shost->max_lun = ADV_MAX_LUN + 1; 11198 shost->max_cmd_len = ADV_MAX_CDB_LEN; 11199 11200 /* 11201 * Save the I/O Port address and length even though 11202 * I/O ports are not used to access Wide boards. 11203 * Instead the Wide boards are accessed with 11204 * PCI Memory Mapped I/O. 11205 */ 11206 shost->io_port = iop; 11207 11208 shost->this_id = adv_dvc_varp->chip_scsi_id; 11209 11210 /* Set maximum number of queues the adapter can handle. */ 11211 shost->can_queue = adv_dvc_varp->max_host_qng; 11212 } 11213 11214 /* 11215 * Set the maximum number of scatter-gather elements the 11216 * adapter can handle. 11217 */ 11218 if (ASC_NARROW_BOARD(boardp)) { 11219 /* 11220 * Allow two commands with 'sg_tablesize' scatter-gather 11221 * elements to be executed simultaneously. This value is 11222 * the theoretical hardware limit. It may be decreased 11223 * below. 11224 */ 11225 shost->sg_tablesize = 11226 (((asc_dvc_varp->max_total_qng - 2) / 2) * 11227 ASC_SG_LIST_PER_Q) + 1; 11228 } else { 11229 shost->sg_tablesize = ADV_MAX_SG_LIST; 11230 } 11231 11232 /* 11233 * The value of 'sg_tablesize' can not exceed the SCSI 11234 * mid-level driver definition of SG_ALL. SG_ALL also 11235 * must not be exceeded, because it is used to define the 11236 * size of the scatter-gather table in 'struct asc_sg_head'. 11237 */ 11238 if (shost->sg_tablesize > SG_ALL) { 11239 shost->sg_tablesize = SG_ALL; 11240 } 11241 11242 ASC_DBG(1, "sg_tablesize: %d\n", shost->sg_tablesize); 11243 11244 /* BIOS start address. */ 11245 if (ASC_NARROW_BOARD(boardp)) { 11246 shost->base = AscGetChipBiosAddress(asc_dvc_varp->iop_base, 11247 asc_dvc_varp->bus_type); 11248 } else { 11249 /* 11250 * Fill-in BIOS board variables. The Wide BIOS saves 11251 * information in LRAM that is used by the driver. 11252 */ 11253 AdvReadWordLram(adv_dvc_varp->iop_base, 11254 BIOS_SIGNATURE, boardp->bios_signature); 11255 AdvReadWordLram(adv_dvc_varp->iop_base, 11256 BIOS_VERSION, boardp->bios_version); 11257 AdvReadWordLram(adv_dvc_varp->iop_base, 11258 BIOS_CODESEG, boardp->bios_codeseg); 11259 AdvReadWordLram(adv_dvc_varp->iop_base, 11260 BIOS_CODELEN, boardp->bios_codelen); 11261 11262 ASC_DBG(1, "bios_signature 0x%x, bios_version 0x%x\n", 11263 boardp->bios_signature, boardp->bios_version); 11264 11265 ASC_DBG(1, "bios_codeseg 0x%x, bios_codelen 0x%x\n", 11266 boardp->bios_codeseg, boardp->bios_codelen); 11267 11268 /* 11269 * If the BIOS saved a valid signature, then fill in 11270 * the BIOS code segment base address. 11271 */ 11272 if (boardp->bios_signature == 0x55AA) { 11273 /* 11274 * Convert x86 realmode code segment to a linear 11275 * address by shifting left 4. 11276 */ 11277 shost->base = ((ulong)boardp->bios_codeseg << 4); 11278 } else { 11279 shost->base = 0; 11280 } 11281 } 11282 11283 /* 11284 * Register Board Resources - I/O Port, DMA, IRQ 11285 */ 11286 11287 /* Register DMA Channel for Narrow boards. */ 11288 shost->dma_channel = NO_ISA_DMA; /* Default to no ISA DMA. */ 11289 #ifdef CONFIG_ISA 11290 if (ASC_NARROW_BOARD(boardp)) { 11291 /* Register DMA channel for ISA bus. */ 11292 if (asc_dvc_varp->bus_type & ASC_IS_ISA) { 11293 shost->dma_channel = asc_dvc_varp->cfg->isa_dma_channel; 11294 ret = request_dma(shost->dma_channel, DRV_NAME); 11295 if (ret) { 11296 shost_printk(KERN_ERR, shost, "request_dma() " 11297 "%d failed %d\n", 11298 shost->dma_channel, ret); 11299 goto err_unmap; 11300 } 11301 AscEnableIsaDma(shost->dma_channel); 11302 } 11303 } 11304 #endif /* CONFIG_ISA */ 11305 11306 /* Register IRQ Number. */ 11307 ASC_DBG(2, "request_irq(%d, %p)\n", boardp->irq, shost); 11308 11309 ret = request_irq(boardp->irq, advansys_interrupt, share_irq, 11310 DRV_NAME, shost); 11311 11312 if (ret) { 11313 if (ret == -EBUSY) { 11314 shost_printk(KERN_ERR, shost, "request_irq(): IRQ 0x%x " 11315 "already in use\n", boardp->irq); 11316 } else if (ret == -EINVAL) { 11317 shost_printk(KERN_ERR, shost, "request_irq(): IRQ 0x%x " 11318 "not valid\n", boardp->irq); 11319 } else { 11320 shost_printk(KERN_ERR, shost, "request_irq(): IRQ 0x%x " 11321 "failed with %d\n", boardp->irq, ret); 11322 } 11323 goto err_free_dma; 11324 } 11325 11326 /* 11327 * Initialize board RISC chip and enable interrupts. 11328 */ 11329 if (ASC_NARROW_BOARD(boardp)) { 11330 ASC_DBG(2, "AscInitAsc1000Driver()\n"); 11331 11332 asc_dvc_varp->overrun_buf = kzalloc(ASC_OVERRUN_BSIZE, GFP_KERNEL); 11333 if (!asc_dvc_varp->overrun_buf) { 11334 ret = -ENOMEM; 11335 goto err_free_irq; 11336 } 11337 warn_code = AscInitAsc1000Driver(asc_dvc_varp); 11338 11339 if (warn_code || asc_dvc_varp->err_code) { 11340 shost_printk(KERN_ERR, shost, "error: init_state 0x%x, " 11341 "warn 0x%x, error 0x%x\n", 11342 asc_dvc_varp->init_state, warn_code, 11343 asc_dvc_varp->err_code); 11344 if (!asc_dvc_varp->overrun_dma) { 11345 ret = -ENODEV; 11346 goto err_free_mem; 11347 } 11348 } 11349 } else { 11350 if (advansys_wide_init_chip(shost)) { 11351 ret = -ENODEV; 11352 goto err_free_mem; 11353 } 11354 } 11355 11356 ASC_DBG_PRT_SCSI_HOST(2, shost); 11357 11358 ret = scsi_add_host(shost, boardp->dev); 11359 if (ret) 11360 goto err_free_mem; 11361 11362 scsi_scan_host(shost); 11363 return 0; 11364 11365 err_free_mem: 11366 if (ASC_NARROW_BOARD(boardp)) { 11367 if (asc_dvc_varp->overrun_dma) 11368 dma_unmap_single(boardp->dev, asc_dvc_varp->overrun_dma, 11369 ASC_OVERRUN_BSIZE, DMA_FROM_DEVICE); 11370 kfree(asc_dvc_varp->overrun_buf); 11371 } else 11372 advansys_wide_free_mem(boardp); 11373 err_free_irq: 11374 free_irq(boardp->irq, shost); 11375 err_free_dma: 11376 #ifdef CONFIG_ISA 11377 if (shost->dma_channel != NO_ISA_DMA) 11378 free_dma(shost->dma_channel); 11379 #endif 11380 err_unmap: 11381 if (boardp->ioremap_addr) 11382 iounmap(boardp->ioremap_addr); 11383 #ifdef CONFIG_PCI 11384 err_shost: 11385 #endif 11386 return ret; 11387 } 11388 11389 /* 11390 * advansys_release() 11391 * 11392 * Release resources allocated for a single AdvanSys adapter. 11393 */ 11394 static int advansys_release(struct Scsi_Host *shost) 11395 { 11396 struct asc_board *board = shost_priv(shost); 11397 ASC_DBG(1, "begin\n"); 11398 scsi_remove_host(shost); 11399 free_irq(board->irq, shost); 11400 #ifdef CONFIG_ISA 11401 if (shost->dma_channel != NO_ISA_DMA) { 11402 ASC_DBG(1, "free_dma()\n"); 11403 free_dma(shost->dma_channel); 11404 } 11405 #endif 11406 if (ASC_NARROW_BOARD(board)) { 11407 dma_unmap_single(board->dev, 11408 board->dvc_var.asc_dvc_var.overrun_dma, 11409 ASC_OVERRUN_BSIZE, DMA_FROM_DEVICE); 11410 kfree(board->dvc_var.asc_dvc_var.overrun_buf); 11411 } else { 11412 iounmap(board->ioremap_addr); 11413 advansys_wide_free_mem(board); 11414 } 11415 scsi_host_put(shost); 11416 ASC_DBG(1, "end\n"); 11417 return 0; 11418 } 11419 11420 #define ASC_IOADR_TABLE_MAX_IX 11 11421 11422 static PortAddr _asc_def_iop_base[ASC_IOADR_TABLE_MAX_IX] = { 11423 0x100, 0x0110, 0x120, 0x0130, 0x140, 0x0150, 0x0190, 11424 0x0210, 0x0230, 0x0250, 0x0330 11425 }; 11426 11427 /* 11428 * The ISA IRQ number is found in bits 2 and 3 of the CfgLsw. It decodes as: 11429 * 00: 10 11430 * 01: 11 11431 * 10: 12 11432 * 11: 15 11433 */ 11434 static unsigned int advansys_isa_irq_no(PortAddr iop_base) 11435 { 11436 unsigned short cfg_lsw = AscGetChipCfgLsw(iop_base); 11437 unsigned int chip_irq = ((cfg_lsw >> 2) & 0x03) + 10; 11438 if (chip_irq == 13) 11439 chip_irq = 15; 11440 return chip_irq; 11441 } 11442 11443 static int advansys_isa_probe(struct device *dev, unsigned int id) 11444 { 11445 int err = -ENODEV; 11446 PortAddr iop_base = _asc_def_iop_base[id]; 11447 struct Scsi_Host *shost; 11448 struct asc_board *board; 11449 11450 if (!request_region(iop_base, ASC_IOADR_GAP, DRV_NAME)) { 11451 ASC_DBG(1, "I/O port 0x%x busy\n", iop_base); 11452 return -ENODEV; 11453 } 11454 ASC_DBG(1, "probing I/O port 0x%x\n", iop_base); 11455 if (!AscFindSignature(iop_base)) 11456 goto release_region; 11457 if (!(AscGetChipVersion(iop_base, ASC_IS_ISA) & ASC_CHIP_VER_ISA_BIT)) 11458 goto release_region; 11459 11460 err = -ENOMEM; 11461 shost = scsi_host_alloc(&advansys_template, sizeof(*board)); 11462 if (!shost) 11463 goto release_region; 11464 11465 board = shost_priv(shost); 11466 board->irq = advansys_isa_irq_no(iop_base); 11467 board->dev = dev; 11468 board->shost = shost; 11469 11470 err = advansys_board_found(shost, iop_base, ASC_IS_ISA); 11471 if (err) 11472 goto free_host; 11473 11474 dev_set_drvdata(dev, shost); 11475 return 0; 11476 11477 free_host: 11478 scsi_host_put(shost); 11479 release_region: 11480 release_region(iop_base, ASC_IOADR_GAP); 11481 return err; 11482 } 11483 11484 static int advansys_isa_remove(struct device *dev, unsigned int id) 11485 { 11486 int ioport = _asc_def_iop_base[id]; 11487 advansys_release(dev_get_drvdata(dev)); 11488 release_region(ioport, ASC_IOADR_GAP); 11489 return 0; 11490 } 11491 11492 static struct isa_driver advansys_isa_driver = { 11493 .probe = advansys_isa_probe, 11494 .remove = advansys_isa_remove, 11495 .driver = { 11496 .owner = THIS_MODULE, 11497 .name = DRV_NAME, 11498 }, 11499 }; 11500 11501 /* 11502 * The VLB IRQ number is found in bits 2 to 4 of the CfgLsw. It decodes as: 11503 * 000: invalid 11504 * 001: 10 11505 * 010: 11 11506 * 011: 12 11507 * 100: invalid 11508 * 101: 14 11509 * 110: 15 11510 * 111: invalid 11511 */ 11512 static unsigned int advansys_vlb_irq_no(PortAddr iop_base) 11513 { 11514 unsigned short cfg_lsw = AscGetChipCfgLsw(iop_base); 11515 unsigned int chip_irq = ((cfg_lsw >> 2) & 0x07) + 9; 11516 if ((chip_irq < 10) || (chip_irq == 13) || (chip_irq > 15)) 11517 return 0; 11518 return chip_irq; 11519 } 11520 11521 static int advansys_vlb_probe(struct device *dev, unsigned int id) 11522 { 11523 int err = -ENODEV; 11524 PortAddr iop_base = _asc_def_iop_base[id]; 11525 struct Scsi_Host *shost; 11526 struct asc_board *board; 11527 11528 if (!request_region(iop_base, ASC_IOADR_GAP, DRV_NAME)) { 11529 ASC_DBG(1, "I/O port 0x%x busy\n", iop_base); 11530 return -ENODEV; 11531 } 11532 ASC_DBG(1, "probing I/O port 0x%x\n", iop_base); 11533 if (!AscFindSignature(iop_base)) 11534 goto release_region; 11535 /* 11536 * I don't think this condition can actually happen, but the old 11537 * driver did it, and the chances of finding a VLB setup in 2007 11538 * to do testing with is slight to none. 11539 */ 11540 if (AscGetChipVersion(iop_base, ASC_IS_VL) > ASC_CHIP_MAX_VER_VL) 11541 goto release_region; 11542 11543 err = -ENOMEM; 11544 shost = scsi_host_alloc(&advansys_template, sizeof(*board)); 11545 if (!shost) 11546 goto release_region; 11547 11548 board = shost_priv(shost); 11549 board->irq = advansys_vlb_irq_no(iop_base); 11550 board->dev = dev; 11551 board->shost = shost; 11552 11553 err = advansys_board_found(shost, iop_base, ASC_IS_VL); 11554 if (err) 11555 goto free_host; 11556 11557 dev_set_drvdata(dev, shost); 11558 return 0; 11559 11560 free_host: 11561 scsi_host_put(shost); 11562 release_region: 11563 release_region(iop_base, ASC_IOADR_GAP); 11564 return -ENODEV; 11565 } 11566 11567 static struct isa_driver advansys_vlb_driver = { 11568 .probe = advansys_vlb_probe, 11569 .remove = advansys_isa_remove, 11570 .driver = { 11571 .owner = THIS_MODULE, 11572 .name = "advansys_vlb", 11573 }, 11574 }; 11575 11576 static struct eisa_device_id advansys_eisa_table[] = { 11577 { "ABP7401" }, 11578 { "ABP7501" }, 11579 { "" } 11580 }; 11581 11582 MODULE_DEVICE_TABLE(eisa, advansys_eisa_table); 11583 11584 /* 11585 * EISA is a little more tricky than PCI; each EISA device may have two 11586 * channels, and this driver is written to make each channel its own Scsi_Host 11587 */ 11588 struct eisa_scsi_data { 11589 struct Scsi_Host *host[2]; 11590 }; 11591 11592 /* 11593 * The EISA IRQ number is found in bits 8 to 10 of the CfgLsw. It decodes as: 11594 * 000: 10 11595 * 001: 11 11596 * 010: 12 11597 * 011: invalid 11598 * 100: 14 11599 * 101: 15 11600 * 110: invalid 11601 * 111: invalid 11602 */ 11603 static unsigned int advansys_eisa_irq_no(struct eisa_device *edev) 11604 { 11605 unsigned short cfg_lsw = inw(edev->base_addr + 0xc86); 11606 unsigned int chip_irq = ((cfg_lsw >> 8) & 0x07) + 10; 11607 if ((chip_irq == 13) || (chip_irq > 15)) 11608 return 0; 11609 return chip_irq; 11610 } 11611 11612 static int advansys_eisa_probe(struct device *dev) 11613 { 11614 int i, ioport, irq = 0; 11615 int err; 11616 struct eisa_device *edev = to_eisa_device(dev); 11617 struct eisa_scsi_data *data; 11618 11619 err = -ENOMEM; 11620 data = kzalloc(sizeof(*data), GFP_KERNEL); 11621 if (!data) 11622 goto fail; 11623 ioport = edev->base_addr + 0xc30; 11624 11625 err = -ENODEV; 11626 for (i = 0; i < 2; i++, ioport += 0x20) { 11627 struct asc_board *board; 11628 struct Scsi_Host *shost; 11629 if (!request_region(ioport, ASC_IOADR_GAP, DRV_NAME)) { 11630 printk(KERN_WARNING "Region %x-%x busy\n", ioport, 11631 ioport + ASC_IOADR_GAP - 1); 11632 continue; 11633 } 11634 if (!AscFindSignature(ioport)) { 11635 release_region(ioport, ASC_IOADR_GAP); 11636 continue; 11637 } 11638 11639 /* 11640 * I don't know why we need to do this for EISA chips, but 11641 * not for any others. It looks to be equivalent to 11642 * AscGetChipCfgMsw, but I may have overlooked something, 11643 * so I'm not converting it until I get an EISA board to 11644 * test with. 11645 */ 11646 inw(ioport + 4); 11647 11648 if (!irq) 11649 irq = advansys_eisa_irq_no(edev); 11650 11651 err = -ENOMEM; 11652 shost = scsi_host_alloc(&advansys_template, sizeof(*board)); 11653 if (!shost) 11654 goto release_region; 11655 11656 board = shost_priv(shost); 11657 board->irq = irq; 11658 board->dev = dev; 11659 board->shost = shost; 11660 11661 err = advansys_board_found(shost, ioport, ASC_IS_EISA); 11662 if (!err) { 11663 data->host[i] = shost; 11664 continue; 11665 } 11666 11667 scsi_host_put(shost); 11668 release_region: 11669 release_region(ioport, ASC_IOADR_GAP); 11670 break; 11671 } 11672 11673 if (err) 11674 goto free_data; 11675 dev_set_drvdata(dev, data); 11676 return 0; 11677 11678 free_data: 11679 kfree(data->host[0]); 11680 kfree(data->host[1]); 11681 kfree(data); 11682 fail: 11683 return err; 11684 } 11685 11686 static int advansys_eisa_remove(struct device *dev) 11687 { 11688 int i; 11689 struct eisa_scsi_data *data = dev_get_drvdata(dev); 11690 11691 for (i = 0; i < 2; i++) { 11692 int ioport; 11693 struct Scsi_Host *shost = data->host[i]; 11694 if (!shost) 11695 continue; 11696 ioport = shost->io_port; 11697 advansys_release(shost); 11698 release_region(ioport, ASC_IOADR_GAP); 11699 } 11700 11701 kfree(data); 11702 return 0; 11703 } 11704 11705 static struct eisa_driver advansys_eisa_driver = { 11706 .id_table = advansys_eisa_table, 11707 .driver = { 11708 .name = DRV_NAME, 11709 .probe = advansys_eisa_probe, 11710 .remove = advansys_eisa_remove, 11711 } 11712 }; 11713 11714 /* PCI Devices supported by this driver */ 11715 static struct pci_device_id advansys_pci_tbl[] = { 11716 {PCI_VENDOR_ID_ASP, PCI_DEVICE_ID_ASP_1200A, 11717 PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, 11718 {PCI_VENDOR_ID_ASP, PCI_DEVICE_ID_ASP_ABP940, 11719 PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, 11720 {PCI_VENDOR_ID_ASP, PCI_DEVICE_ID_ASP_ABP940U, 11721 PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, 11722 {PCI_VENDOR_ID_ASP, PCI_DEVICE_ID_ASP_ABP940UW, 11723 PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, 11724 {PCI_VENDOR_ID_ASP, PCI_DEVICE_ID_38C0800_REV1, 11725 PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, 11726 {PCI_VENDOR_ID_ASP, PCI_DEVICE_ID_38C1600_REV1, 11727 PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, 11728 {} 11729 }; 11730 11731 MODULE_DEVICE_TABLE(pci, advansys_pci_tbl); 11732 11733 static void advansys_set_latency(struct pci_dev *pdev) 11734 { 11735 if ((pdev->device == PCI_DEVICE_ID_ASP_1200A) || 11736 (pdev->device == PCI_DEVICE_ID_ASP_ABP940)) { 11737 pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0); 11738 } else { 11739 u8 latency; 11740 pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &latency); 11741 if (latency < 0x20) 11742 pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x20); 11743 } 11744 } 11745 11746 static int advansys_pci_probe(struct pci_dev *pdev, 11747 const struct pci_device_id *ent) 11748 { 11749 int err, ioport; 11750 struct Scsi_Host *shost; 11751 struct asc_board *board; 11752 11753 err = pci_enable_device(pdev); 11754 if (err) 11755 goto fail; 11756 err = pci_request_regions(pdev, DRV_NAME); 11757 if (err) 11758 goto disable_device; 11759 pci_set_master(pdev); 11760 advansys_set_latency(pdev); 11761 11762 err = -ENODEV; 11763 if (pci_resource_len(pdev, 0) == 0) 11764 goto release_region; 11765 11766 ioport = pci_resource_start(pdev, 0); 11767 11768 err = -ENOMEM; 11769 shost = scsi_host_alloc(&advansys_template, sizeof(*board)); 11770 if (!shost) 11771 goto release_region; 11772 11773 board = shost_priv(shost); 11774 board->irq = pdev->irq; 11775 board->dev = &pdev->dev; 11776 board->shost = shost; 11777 11778 if (pdev->device == PCI_DEVICE_ID_ASP_ABP940UW || 11779 pdev->device == PCI_DEVICE_ID_38C0800_REV1 || 11780 pdev->device == PCI_DEVICE_ID_38C1600_REV1) { 11781 board->flags |= ASC_IS_WIDE_BOARD; 11782 } 11783 11784 err = advansys_board_found(shost, ioport, ASC_IS_PCI); 11785 if (err) 11786 goto free_host; 11787 11788 pci_set_drvdata(pdev, shost); 11789 return 0; 11790 11791 free_host: 11792 scsi_host_put(shost); 11793 release_region: 11794 pci_release_regions(pdev); 11795 disable_device: 11796 pci_disable_device(pdev); 11797 fail: 11798 return err; 11799 } 11800 11801 static void advansys_pci_remove(struct pci_dev *pdev) 11802 { 11803 advansys_release(pci_get_drvdata(pdev)); 11804 pci_release_regions(pdev); 11805 pci_disable_device(pdev); 11806 } 11807 11808 static struct pci_driver advansys_pci_driver = { 11809 .name = DRV_NAME, 11810 .id_table = advansys_pci_tbl, 11811 .probe = advansys_pci_probe, 11812 .remove = advansys_pci_remove, 11813 }; 11814 11815 static int __init advansys_init(void) 11816 { 11817 int error; 11818 11819 error = isa_register_driver(&advansys_isa_driver, 11820 ASC_IOADR_TABLE_MAX_IX); 11821 if (error) 11822 goto fail; 11823 11824 error = isa_register_driver(&advansys_vlb_driver, 11825 ASC_IOADR_TABLE_MAX_IX); 11826 if (error) 11827 goto unregister_isa; 11828 11829 error = eisa_driver_register(&advansys_eisa_driver); 11830 if (error) 11831 goto unregister_vlb; 11832 11833 error = pci_register_driver(&advansys_pci_driver); 11834 if (error) 11835 goto unregister_eisa; 11836 11837 return 0; 11838 11839 unregister_eisa: 11840 eisa_driver_unregister(&advansys_eisa_driver); 11841 unregister_vlb: 11842 isa_unregister_driver(&advansys_vlb_driver); 11843 unregister_isa: 11844 isa_unregister_driver(&advansys_isa_driver); 11845 fail: 11846 return error; 11847 } 11848 11849 static void __exit advansys_exit(void) 11850 { 11851 pci_unregister_driver(&advansys_pci_driver); 11852 eisa_driver_unregister(&advansys_eisa_driver); 11853 isa_unregister_driver(&advansys_vlb_driver); 11854 isa_unregister_driver(&advansys_isa_driver); 11855 } 11856 11857 module_init(advansys_init); 11858 module_exit(advansys_exit); 11859 11860 MODULE_LICENSE("GPL"); 11861 MODULE_FIRMWARE("advansys/mcode.bin"); 11862 MODULE_FIRMWARE("advansys/3550.bin"); 11863 MODULE_FIRMWARE("advansys/38C0800.bin"); 11864 MODULE_FIRMWARE("advansys/38C1600.bin"); 11865