1 // SPDX-License-Identifier: GPL-2.0-or-later 2 /* 3 * Adaptec AAC series RAID controller driver 4 * (c) Copyright 2001 Red Hat Inc. 5 * 6 * based on the old aacraid driver that is.. 7 * Adaptec aacraid device driver for Linux. 8 * 9 * Copyright (c) 2000-2010 Adaptec, Inc. 10 * 2010-2015 PMC-Sierra, Inc. (aacraid@pmc-sierra.com) 11 * 2016-2017 Microsemi Corp. (aacraid@microsemi.com) 12 * 13 * Module Name: 14 * linit.c 15 * 16 * Abstract: Linux Driver entry module for Adaptec RAID Array Controller 17 */ 18 19 20 #include <linux/compat.h> 21 #include <linux/blkdev.h> 22 #include <linux/completion.h> 23 #include <linux/init.h> 24 #include <linux/interrupt.h> 25 #include <linux/kernel.h> 26 #include <linux/module.h> 27 #include <linux/moduleparam.h> 28 #include <linux/pci.h> 29 #include <linux/aer.h> 30 #include <linux/slab.h> 31 #include <linux/mutex.h> 32 #include <linux/spinlock.h> 33 #include <linux/syscalls.h> 34 #include <linux/delay.h> 35 #include <linux/kthread.h> 36 #include <linux/msdos_partition.h> 37 38 #include <scsi/scsi.h> 39 #include <scsi/scsi_cmnd.h> 40 #include <scsi/scsi_device.h> 41 #include <scsi/scsi_host.h> 42 #include <scsi/scsi_tcq.h> 43 #include <scsi/scsicam.h> 44 #include <scsi/scsi_eh.h> 45 46 #include "aacraid.h" 47 48 #define AAC_DRIVER_VERSION "1.2.1" 49 #ifndef AAC_DRIVER_BRANCH 50 #define AAC_DRIVER_BRANCH "" 51 #endif 52 #define AAC_DRIVERNAME "aacraid" 53 54 #ifdef AAC_DRIVER_BUILD 55 #define _str(x) #x 56 #define str(x) _str(x) 57 #define AAC_DRIVER_FULL_VERSION AAC_DRIVER_VERSION "[" str(AAC_DRIVER_BUILD) "]" AAC_DRIVER_BRANCH 58 #else 59 #define AAC_DRIVER_FULL_VERSION AAC_DRIVER_VERSION AAC_DRIVER_BRANCH 60 #endif 61 62 MODULE_AUTHOR("Red Hat Inc and Adaptec"); 63 MODULE_DESCRIPTION("Dell PERC2, 2/Si, 3/Si, 3/Di, " 64 "Adaptec Advanced Raid Products, " 65 "HP NetRAID-4M, IBM ServeRAID & ICP SCSI driver"); 66 MODULE_LICENSE("GPL"); 67 MODULE_VERSION(AAC_DRIVER_FULL_VERSION); 68 69 static DEFINE_MUTEX(aac_mutex); 70 static LIST_HEAD(aac_devices); 71 static int aac_cfg_major = AAC_CHARDEV_UNREGISTERED; 72 char aac_driver_version[] = AAC_DRIVER_FULL_VERSION; 73 74 /* 75 * Because of the way Linux names scsi devices, the order in this table has 76 * become important. Check for on-board Raid first, add-in cards second. 77 * 78 * Note: The last field is used to index into aac_drivers below. 79 */ 80 static const struct pci_device_id aac_pci_tbl[] = { 81 { 0x1028, 0x0001, 0x1028, 0x0001, 0, 0, 0 }, /* PERC 2/Si (Iguana/PERC2Si) */ 82 { 0x1028, 0x0002, 0x1028, 0x0002, 0, 0, 1 }, /* PERC 3/Di (Opal/PERC3Di) */ 83 { 0x1028, 0x0003, 0x1028, 0x0003, 0, 0, 2 }, /* PERC 3/Si (SlimFast/PERC3Si */ 84 { 0x1028, 0x0004, 0x1028, 0x00d0, 0, 0, 3 }, /* PERC 3/Di (Iguana FlipChip/PERC3DiF */ 85 { 0x1028, 0x0002, 0x1028, 0x00d1, 0, 0, 4 }, /* PERC 3/Di (Viper/PERC3DiV) */ 86 { 0x1028, 0x0002, 0x1028, 0x00d9, 0, 0, 5 }, /* PERC 3/Di (Lexus/PERC3DiL) */ 87 { 0x1028, 0x000a, 0x1028, 0x0106, 0, 0, 6 }, /* PERC 3/Di (Jaguar/PERC3DiJ) */ 88 { 0x1028, 0x000a, 0x1028, 0x011b, 0, 0, 7 }, /* PERC 3/Di (Dagger/PERC3DiD) */ 89 { 0x1028, 0x000a, 0x1028, 0x0121, 0, 0, 8 }, /* PERC 3/Di (Boxster/PERC3DiB) */ 90 { 0x9005, 0x0283, 0x9005, 0x0283, 0, 0, 9 }, /* catapult */ 91 { 0x9005, 0x0284, 0x9005, 0x0284, 0, 0, 10 }, /* tomcat */ 92 { 0x9005, 0x0285, 0x9005, 0x0286, 0, 0, 11 }, /* Adaptec 2120S (Crusader) */ 93 { 0x9005, 0x0285, 0x9005, 0x0285, 0, 0, 12 }, /* Adaptec 2200S (Vulcan) */ 94 { 0x9005, 0x0285, 0x9005, 0x0287, 0, 0, 13 }, /* Adaptec 2200S (Vulcan-2m) */ 95 { 0x9005, 0x0285, 0x17aa, 0x0286, 0, 0, 14 }, /* Legend S220 (Legend Crusader) */ 96 { 0x9005, 0x0285, 0x17aa, 0x0287, 0, 0, 15 }, /* Legend S230 (Legend Vulcan) */ 97 98 { 0x9005, 0x0285, 0x9005, 0x0288, 0, 0, 16 }, /* Adaptec 3230S (Harrier) */ 99 { 0x9005, 0x0285, 0x9005, 0x0289, 0, 0, 17 }, /* Adaptec 3240S (Tornado) */ 100 { 0x9005, 0x0285, 0x9005, 0x028a, 0, 0, 18 }, /* ASR-2020ZCR SCSI PCI-X ZCR (Skyhawk) */ 101 { 0x9005, 0x0285, 0x9005, 0x028b, 0, 0, 19 }, /* ASR-2025ZCR SCSI SO-DIMM PCI-X ZCR (Terminator) */ 102 { 0x9005, 0x0286, 0x9005, 0x028c, 0, 0, 20 }, /* ASR-2230S + ASR-2230SLP PCI-X (Lancer) */ 103 { 0x9005, 0x0286, 0x9005, 0x028d, 0, 0, 21 }, /* ASR-2130S (Lancer) */ 104 { 0x9005, 0x0286, 0x9005, 0x029b, 0, 0, 22 }, /* AAR-2820SA (Intruder) */ 105 { 0x9005, 0x0286, 0x9005, 0x029c, 0, 0, 23 }, /* AAR-2620SA (Intruder) */ 106 { 0x9005, 0x0286, 0x9005, 0x029d, 0, 0, 24 }, /* AAR-2420SA (Intruder) */ 107 { 0x9005, 0x0286, 0x9005, 0x029e, 0, 0, 25 }, /* ICP9024RO (Lancer) */ 108 { 0x9005, 0x0286, 0x9005, 0x029f, 0, 0, 26 }, /* ICP9014RO (Lancer) */ 109 { 0x9005, 0x0286, 0x9005, 0x02a0, 0, 0, 27 }, /* ICP9047MA (Lancer) */ 110 { 0x9005, 0x0286, 0x9005, 0x02a1, 0, 0, 28 }, /* ICP9087MA (Lancer) */ 111 { 0x9005, 0x0286, 0x9005, 0x02a3, 0, 0, 29 }, /* ICP5445AU (Hurricane44) */ 112 { 0x9005, 0x0285, 0x9005, 0x02a4, 0, 0, 30 }, /* ICP9085LI (Marauder-X) */ 113 { 0x9005, 0x0285, 0x9005, 0x02a5, 0, 0, 31 }, /* ICP5085BR (Marauder-E) */ 114 { 0x9005, 0x0286, 0x9005, 0x02a6, 0, 0, 32 }, /* ICP9067MA (Intruder-6) */ 115 { 0x9005, 0x0287, 0x9005, 0x0800, 0, 0, 33 }, /* Themisto Jupiter Platform */ 116 { 0x9005, 0x0200, 0x9005, 0x0200, 0, 0, 33 }, /* Themisto Jupiter Platform */ 117 { 0x9005, 0x0286, 0x9005, 0x0800, 0, 0, 34 }, /* Callisto Jupiter Platform */ 118 { 0x9005, 0x0285, 0x9005, 0x028e, 0, 0, 35 }, /* ASR-2020SA SATA PCI-X ZCR (Skyhawk) */ 119 { 0x9005, 0x0285, 0x9005, 0x028f, 0, 0, 36 }, /* ASR-2025SA SATA SO-DIMM PCI-X ZCR (Terminator) */ 120 { 0x9005, 0x0285, 0x9005, 0x0290, 0, 0, 37 }, /* AAR-2410SA PCI SATA 4ch (Jaguar II) */ 121 { 0x9005, 0x0285, 0x1028, 0x0291, 0, 0, 38 }, /* CERC SATA RAID 2 PCI SATA 6ch (DellCorsair) */ 122 { 0x9005, 0x0285, 0x9005, 0x0292, 0, 0, 39 }, /* AAR-2810SA PCI SATA 8ch (Corsair-8) */ 123 { 0x9005, 0x0285, 0x9005, 0x0293, 0, 0, 40 }, /* AAR-21610SA PCI SATA 16ch (Corsair-16) */ 124 { 0x9005, 0x0285, 0x9005, 0x0294, 0, 0, 41 }, /* ESD SO-DIMM PCI-X SATA ZCR (Prowler) */ 125 { 0x9005, 0x0285, 0x103C, 0x3227, 0, 0, 42 }, /* AAR-2610SA PCI SATA 6ch */ 126 { 0x9005, 0x0285, 0x9005, 0x0296, 0, 0, 43 }, /* ASR-2240S (SabreExpress) */ 127 { 0x9005, 0x0285, 0x9005, 0x0297, 0, 0, 44 }, /* ASR-4005 */ 128 { 0x9005, 0x0285, 0x1014, 0x02F2, 0, 0, 45 }, /* IBM 8i (AvonPark) */ 129 { 0x9005, 0x0285, 0x1014, 0x0312, 0, 0, 45 }, /* IBM 8i (AvonPark Lite) */ 130 { 0x9005, 0x0286, 0x1014, 0x9580, 0, 0, 46 }, /* IBM 8k/8k-l8 (Aurora) */ 131 { 0x9005, 0x0286, 0x1014, 0x9540, 0, 0, 47 }, /* IBM 8k/8k-l4 (Aurora Lite) */ 132 { 0x9005, 0x0285, 0x9005, 0x0298, 0, 0, 48 }, /* ASR-4000 (BlackBird) */ 133 { 0x9005, 0x0285, 0x9005, 0x0299, 0, 0, 49 }, /* ASR-4800SAS (Marauder-X) */ 134 { 0x9005, 0x0285, 0x9005, 0x029a, 0, 0, 50 }, /* ASR-4805SAS (Marauder-E) */ 135 { 0x9005, 0x0286, 0x9005, 0x02a2, 0, 0, 51 }, /* ASR-3800 (Hurricane44) */ 136 137 { 0x9005, 0x0285, 0x1028, 0x0287, 0, 0, 52 }, /* Perc 320/DC*/ 138 { 0x1011, 0x0046, 0x9005, 0x0365, 0, 0, 53 }, /* Adaptec 5400S (Mustang)*/ 139 { 0x1011, 0x0046, 0x9005, 0x0364, 0, 0, 54 }, /* Adaptec 5400S (Mustang)*/ 140 { 0x1011, 0x0046, 0x9005, 0x1364, 0, 0, 55 }, /* Dell PERC2/QC */ 141 { 0x1011, 0x0046, 0x103c, 0x10c2, 0, 0, 56 }, /* HP NetRAID-4M */ 142 143 { 0x9005, 0x0285, 0x1028, PCI_ANY_ID, 0, 0, 57 }, /* Dell Catchall */ 144 { 0x9005, 0x0285, 0x17aa, PCI_ANY_ID, 0, 0, 58 }, /* Legend Catchall */ 145 { 0x9005, 0x0285, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 59 }, /* Adaptec Catch All */ 146 { 0x9005, 0x0286, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 60 }, /* Adaptec Rocket Catch All */ 147 { 0x9005, 0x0288, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 61 }, /* Adaptec NEMER/ARK Catch All */ 148 { 0x9005, 0x028b, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 62 }, /* Adaptec PMC Series 6 (Tupelo) */ 149 { 0x9005, 0x028c, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 63 }, /* Adaptec PMC Series 7 (Denali) */ 150 { 0x9005, 0x028d, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 64 }, /* Adaptec PMC Series 8 */ 151 { 0,} 152 }; 153 MODULE_DEVICE_TABLE(pci, aac_pci_tbl); 154 155 /* 156 * dmb - For now we add the number of channels to this structure. 157 * In the future we should add a fib that reports the number of channels 158 * for the card. At that time we can remove the channels from here 159 */ 160 static struct aac_driver_ident aac_drivers[] = { 161 { aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* PERC 2/Si (Iguana/PERC2Si) */ 162 { aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* PERC 3/Di (Opal/PERC3Di) */ 163 { aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* PERC 3/Si (SlimFast/PERC3Si */ 164 { aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* PERC 3/Di (Iguana FlipChip/PERC3DiF */ 165 { aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* PERC 3/Di (Viper/PERC3DiV) */ 166 { aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* PERC 3/Di (Lexus/PERC3DiL) */ 167 { aac_rx_init, "percraid", "DELL ", "PERCRAID ", 1, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* PERC 3/Di (Jaguar/PERC3DiJ) */ 168 { aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* PERC 3/Di (Dagger/PERC3DiD) */ 169 { aac_rx_init, "percraid", "DELL ", "PERCRAID ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* PERC 3/Di (Boxster/PERC3DiB) */ 170 { aac_rx_init, "aacraid", "ADAPTEC ", "catapult ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* catapult */ 171 { aac_rx_init, "aacraid", "ADAPTEC ", "tomcat ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* tomcat */ 172 { aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2120S ", 1, AAC_QUIRK_31BIT | AAC_QUIRK_34SG }, /* Adaptec 2120S (Crusader) */ 173 { aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2200S ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG }, /* Adaptec 2200S (Vulcan) */ 174 { aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 2200S ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* Adaptec 2200S (Vulcan-2m) */ 175 { aac_rx_init, "aacraid", "Legend ", "Legend S220 ", 1, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* Legend S220 (Legend Crusader) */ 176 { aac_rx_init, "aacraid", "Legend ", "Legend S230 ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* Legend S230 (Legend Vulcan) */ 177 178 { aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 3230S ", 2 }, /* Adaptec 3230S (Harrier) */ 179 { aac_rx_init, "aacraid", "ADAPTEC ", "Adaptec 3240S ", 2 }, /* Adaptec 3240S (Tornado) */ 180 { aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2020ZCR ", 2 }, /* ASR-2020ZCR SCSI PCI-X ZCR (Skyhawk) */ 181 { aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2025ZCR ", 2 }, /* ASR-2025ZCR SCSI SO-DIMM PCI-X ZCR (Terminator) */ 182 { aac_rkt_init, "aacraid", "ADAPTEC ", "ASR-2230S PCI-X ", 2 }, /* ASR-2230S + ASR-2230SLP PCI-X (Lancer) */ 183 { aac_rkt_init, "aacraid", "ADAPTEC ", "ASR-2130S PCI-X ", 1 }, /* ASR-2130S (Lancer) */ 184 { aac_rkt_init, "aacraid", "ADAPTEC ", "AAR-2820SA ", 1 }, /* AAR-2820SA (Intruder) */ 185 { aac_rkt_init, "aacraid", "ADAPTEC ", "AAR-2620SA ", 1 }, /* AAR-2620SA (Intruder) */ 186 { aac_rkt_init, "aacraid", "ADAPTEC ", "AAR-2420SA ", 1 }, /* AAR-2420SA (Intruder) */ 187 { aac_rkt_init, "aacraid", "ICP ", "ICP9024RO ", 2 }, /* ICP9024RO (Lancer) */ 188 { aac_rkt_init, "aacraid", "ICP ", "ICP9014RO ", 1 }, /* ICP9014RO (Lancer) */ 189 { aac_rkt_init, "aacraid", "ICP ", "ICP9047MA ", 1 }, /* ICP9047MA (Lancer) */ 190 { aac_rkt_init, "aacraid", "ICP ", "ICP9087MA ", 1 }, /* ICP9087MA (Lancer) */ 191 { aac_rkt_init, "aacraid", "ICP ", "ICP5445AU ", 1 }, /* ICP5445AU (Hurricane44) */ 192 { aac_rx_init, "aacraid", "ICP ", "ICP9085LI ", 1 }, /* ICP9085LI (Marauder-X) */ 193 { aac_rx_init, "aacraid", "ICP ", "ICP5085BR ", 1 }, /* ICP5085BR (Marauder-E) */ 194 { aac_rkt_init, "aacraid", "ICP ", "ICP9067MA ", 1 }, /* ICP9067MA (Intruder-6) */ 195 { NULL , "aacraid", "ADAPTEC ", "Themisto ", 0, AAC_QUIRK_SLAVE }, /* Jupiter Platform */ 196 { aac_rkt_init, "aacraid", "ADAPTEC ", "Callisto ", 2, AAC_QUIRK_MASTER }, /* Jupiter Platform */ 197 { aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2020SA ", 1 }, /* ASR-2020SA SATA PCI-X ZCR (Skyhawk) */ 198 { aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2025SA ", 1 }, /* ASR-2025SA SATA SO-DIMM PCI-X ZCR (Terminator) */ 199 { aac_rx_init, "aacraid", "ADAPTEC ", "AAR-2410SA SATA ", 1, AAC_QUIRK_17SG }, /* AAR-2410SA PCI SATA 4ch (Jaguar II) */ 200 { aac_rx_init, "aacraid", "DELL ", "CERC SR2 ", 1, AAC_QUIRK_17SG }, /* CERC SATA RAID 2 PCI SATA 6ch (DellCorsair) */ 201 { aac_rx_init, "aacraid", "ADAPTEC ", "AAR-2810SA SATA ", 1, AAC_QUIRK_17SG }, /* AAR-2810SA PCI SATA 8ch (Corsair-8) */ 202 { aac_rx_init, "aacraid", "ADAPTEC ", "AAR-21610SA SATA", 1, AAC_QUIRK_17SG }, /* AAR-21610SA PCI SATA 16ch (Corsair-16) */ 203 { aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2026ZCR ", 1 }, /* ESD SO-DIMM PCI-X SATA ZCR (Prowler) */ 204 { aac_rx_init, "aacraid", "ADAPTEC ", "AAR-2610SA ", 1 }, /* SATA 6Ch (Bearcat) */ 205 { aac_rx_init, "aacraid", "ADAPTEC ", "ASR-2240S ", 1 }, /* ASR-2240S (SabreExpress) */ 206 { aac_rx_init, "aacraid", "ADAPTEC ", "ASR-4005 ", 1 }, /* ASR-4005 */ 207 { aac_rx_init, "ServeRAID","IBM ", "ServeRAID 8i ", 1 }, /* IBM 8i (AvonPark) */ 208 { aac_rkt_init, "ServeRAID","IBM ", "ServeRAID 8k-l8 ", 1 }, /* IBM 8k/8k-l8 (Aurora) */ 209 { aac_rkt_init, "ServeRAID","IBM ", "ServeRAID 8k-l4 ", 1 }, /* IBM 8k/8k-l4 (Aurora Lite) */ 210 { aac_rx_init, "aacraid", "ADAPTEC ", "ASR-4000 ", 1 }, /* ASR-4000 (BlackBird & AvonPark) */ 211 { aac_rx_init, "aacraid", "ADAPTEC ", "ASR-4800SAS ", 1 }, /* ASR-4800SAS (Marauder-X) */ 212 { aac_rx_init, "aacraid", "ADAPTEC ", "ASR-4805SAS ", 1 }, /* ASR-4805SAS (Marauder-E) */ 213 { aac_rkt_init, "aacraid", "ADAPTEC ", "ASR-3800 ", 1 }, /* ASR-3800 (Hurricane44) */ 214 215 { aac_rx_init, "percraid", "DELL ", "PERC 320/DC ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG }, /* Perc 320/DC*/ 216 { aac_sa_init, "aacraid", "ADAPTEC ", "Adaptec 5400S ", 4, AAC_QUIRK_34SG }, /* Adaptec 5400S (Mustang)*/ 217 { aac_sa_init, "aacraid", "ADAPTEC ", "AAC-364 ", 4, AAC_QUIRK_34SG }, /* Adaptec 5400S (Mustang)*/ 218 { aac_sa_init, "percraid", "DELL ", "PERCRAID ", 4, AAC_QUIRK_34SG }, /* Dell PERC2/QC */ 219 { aac_sa_init, "hpnraid", "HP ", "NetRAID ", 4, AAC_QUIRK_34SG }, /* HP NetRAID-4M */ 220 221 { aac_rx_init, "aacraid", "DELL ", "RAID ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* Dell Catchall */ 222 { aac_rx_init, "aacraid", "Legend ", "RAID ", 2, AAC_QUIRK_31BIT | AAC_QUIRK_34SG | AAC_QUIRK_SCSI_32 }, /* Legend Catchall */ 223 { aac_rx_init, "aacraid", "ADAPTEC ", "RAID ", 2 }, /* Adaptec Catch All */ 224 { aac_rkt_init, "aacraid", "ADAPTEC ", "RAID ", 2 }, /* Adaptec Rocket Catch All */ 225 { aac_nark_init, "aacraid", "ADAPTEC ", "RAID ", 2 }, /* Adaptec NEMER/ARK Catch All */ 226 { aac_src_init, "aacraid", "ADAPTEC ", "RAID ", 2, AAC_QUIRK_SRC }, /* Adaptec PMC Series 6 (Tupelo) */ 227 { aac_srcv_init, "aacraid", "ADAPTEC ", "RAID ", 2, AAC_QUIRK_SRC }, /* Adaptec PMC Series 7 (Denali) */ 228 { aac_srcv_init, "aacraid", "ADAPTEC ", "RAID ", 2, AAC_QUIRK_SRC }, /* Adaptec PMC Series 8 */ 229 }; 230 231 /** 232 * aac_queuecommand - queue a SCSI command 233 * @shost: Scsi host to queue command on 234 * @cmd: SCSI command to queue 235 * 236 * Queues a command for execution by the associated Host Adapter. 237 * 238 * TODO: unify with aac_scsi_cmd(). 239 */ 240 241 static int aac_queuecommand(struct Scsi_Host *shost, 242 struct scsi_cmnd *cmd) 243 { 244 aac_priv(cmd)->owner = AAC_OWNER_LOWLEVEL; 245 246 return aac_scsi_cmd(cmd) ? FAILED : 0; 247 } 248 249 /** 250 * aac_info - Returns the host adapter name 251 * @shost: Scsi host to report on 252 * 253 * Returns a static string describing the device in question 254 */ 255 256 static const char *aac_info(struct Scsi_Host *shost) 257 { 258 struct aac_dev *dev = (struct aac_dev *)shost->hostdata; 259 return aac_drivers[dev->cardtype].name; 260 } 261 262 /** 263 * aac_get_driver_ident 264 * @devtype: index into lookup table 265 * 266 * Returns a pointer to the entry in the driver lookup table. 267 */ 268 269 struct aac_driver_ident* aac_get_driver_ident(int devtype) 270 { 271 return &aac_drivers[devtype]; 272 } 273 274 /** 275 * aac_biosparm - return BIOS parameters for disk 276 * @sdev: The scsi device corresponding to the disk 277 * @bdev: the block device corresponding to the disk 278 * @capacity: the sector capacity of the disk 279 * @geom: geometry block to fill in 280 * 281 * Return the Heads/Sectors/Cylinders BIOS Disk Parameters for Disk. 282 * The default disk geometry is 64 heads, 32 sectors, and the appropriate 283 * number of cylinders so as not to exceed drive capacity. In order for 284 * disks equal to or larger than 1 GB to be addressable by the BIOS 285 * without exceeding the BIOS limitation of 1024 cylinders, Extended 286 * Translation should be enabled. With Extended Translation enabled, 287 * drives between 1 GB inclusive and 2 GB exclusive are given a disk 288 * geometry of 128 heads and 32 sectors, and drives above 2 GB inclusive 289 * are given a disk geometry of 255 heads and 63 sectors. However, if 290 * the BIOS detects that the Extended Translation setting does not match 291 * the geometry in the partition table, then the translation inferred 292 * from the partition table will be used by the BIOS, and a warning may 293 * be displayed. 294 */ 295 296 static int aac_biosparm(struct scsi_device *sdev, struct block_device *bdev, 297 sector_t capacity, int *geom) 298 { 299 struct diskparm *param = (struct diskparm *)geom; 300 unsigned char *buf; 301 302 dprintk((KERN_DEBUG "aac_biosparm.\n")); 303 304 /* 305 * Assuming extended translation is enabled - #REVISIT# 306 */ 307 if (capacity >= 2 * 1024 * 1024) { /* 1 GB in 512 byte sectors */ 308 if(capacity >= 4 * 1024 * 1024) { /* 2 GB in 512 byte sectors */ 309 param->heads = 255; 310 param->sectors = 63; 311 } else { 312 param->heads = 128; 313 param->sectors = 32; 314 } 315 } else { 316 param->heads = 64; 317 param->sectors = 32; 318 } 319 320 param->cylinders = cap_to_cyls(capacity, param->heads * param->sectors); 321 322 /* 323 * Read the first 1024 bytes from the disk device, if the boot 324 * sector partition table is valid, search for a partition table 325 * entry whose end_head matches one of the standard geometry 326 * translations ( 64/32, 128/32, 255/63 ). 327 */ 328 buf = scsi_bios_ptable(bdev); 329 if (!buf) 330 return 0; 331 if (*(__le16 *)(buf + 0x40) == cpu_to_le16(MSDOS_LABEL_MAGIC)) { 332 struct msdos_partition *first = (struct msdos_partition *)buf; 333 struct msdos_partition *entry = first; 334 int saved_cylinders = param->cylinders; 335 int num; 336 unsigned char end_head, end_sec; 337 338 for(num = 0; num < 4; num++) { 339 end_head = entry->end_head; 340 end_sec = entry->end_sector & 0x3f; 341 342 if(end_head == 63) { 343 param->heads = 64; 344 param->sectors = 32; 345 break; 346 } else if(end_head == 127) { 347 param->heads = 128; 348 param->sectors = 32; 349 break; 350 } else if(end_head == 254) { 351 param->heads = 255; 352 param->sectors = 63; 353 break; 354 } 355 entry++; 356 } 357 358 if (num == 4) { 359 end_head = first->end_head; 360 end_sec = first->end_sector & 0x3f; 361 } 362 363 param->cylinders = cap_to_cyls(capacity, param->heads * param->sectors); 364 if (num < 4 && end_sec == param->sectors) { 365 if (param->cylinders != saved_cylinders) { 366 dprintk((KERN_DEBUG "Adopting geometry: heads=%d, sectors=%d from partition table %d.\n", 367 param->heads, param->sectors, num)); 368 } 369 } else if (end_head > 0 || end_sec > 0) { 370 dprintk((KERN_DEBUG "Strange geometry: heads=%d, sectors=%d in partition table %d.\n", 371 end_head + 1, end_sec, num)); 372 dprintk((KERN_DEBUG "Using geometry: heads=%d, sectors=%d.\n", 373 param->heads, param->sectors)); 374 } 375 } 376 kfree(buf); 377 return 0; 378 } 379 380 /** 381 * aac_slave_configure - compute queue depths 382 * @sdev: SCSI device we are considering 383 * 384 * Selects queue depths for each target device based on the host adapter's 385 * total capacity and the queue depth supported by the target device. 386 * A queue depth of one automatically disables tagged queueing. 387 */ 388 389 static int aac_slave_configure(struct scsi_device *sdev) 390 { 391 struct aac_dev *aac = (struct aac_dev *)sdev->host->hostdata; 392 int chn, tid; 393 unsigned int depth = 0; 394 unsigned int set_timeout = 0; 395 int timeout = 0; 396 bool set_qd_dev_type = false; 397 u8 devtype = 0; 398 399 chn = aac_logical_to_phys(sdev_channel(sdev)); 400 tid = sdev_id(sdev); 401 if (chn < AAC_MAX_BUSES && tid < AAC_MAX_TARGETS && aac->sa_firmware) { 402 devtype = aac->hba_map[chn][tid].devtype; 403 404 if (devtype == AAC_DEVTYPE_NATIVE_RAW) { 405 depth = aac->hba_map[chn][tid].qd_limit; 406 set_timeout = 1; 407 goto common_config; 408 } 409 if (devtype == AAC_DEVTYPE_ARC_RAW) { 410 set_qd_dev_type = true; 411 set_timeout = 1; 412 goto common_config; 413 } 414 } 415 416 if (aac->jbod && (sdev->type == TYPE_DISK)) 417 sdev->removable = 1; 418 419 if (sdev->type == TYPE_DISK 420 && sdev_channel(sdev) != CONTAINER_CHANNEL 421 && (!aac->jbod || sdev->inq_periph_qual) 422 && (!aac->raid_scsi_mode || (sdev_channel(sdev) != 2))) { 423 424 if (expose_physicals == 0) 425 return -ENXIO; 426 427 if (expose_physicals < 0) 428 sdev->no_uld_attach = 1; 429 } 430 431 if (sdev->tagged_supported 432 && sdev->type == TYPE_DISK 433 && (!aac->raid_scsi_mode || (sdev_channel(sdev) != 2)) 434 && !sdev->no_uld_attach) { 435 436 struct scsi_device * dev; 437 struct Scsi_Host *host = sdev->host; 438 unsigned num_lsu = 0; 439 unsigned num_one = 0; 440 unsigned cid; 441 442 set_timeout = 1; 443 444 for (cid = 0; cid < aac->maximum_num_containers; ++cid) 445 if (aac->fsa_dev[cid].valid) 446 ++num_lsu; 447 448 __shost_for_each_device(dev, host) { 449 if (dev->tagged_supported 450 && dev->type == TYPE_DISK 451 && (!aac->raid_scsi_mode || (sdev_channel(sdev) != 2)) 452 && !dev->no_uld_attach) { 453 if ((sdev_channel(dev) != CONTAINER_CHANNEL) 454 || !aac->fsa_dev[sdev_id(dev)].valid) { 455 ++num_lsu; 456 } 457 } else { 458 ++num_one; 459 } 460 } 461 462 if (num_lsu == 0) 463 ++num_lsu; 464 465 depth = (host->can_queue - num_one) / num_lsu; 466 467 if (sdev_channel(sdev) != NATIVE_CHANNEL) 468 goto common_config; 469 470 set_qd_dev_type = true; 471 472 } 473 474 common_config: 475 476 /* 477 * Check if SATA drive 478 */ 479 if (set_qd_dev_type) { 480 if (strncmp(sdev->vendor, "ATA", 3) == 0) 481 depth = 32; 482 else 483 depth = 64; 484 } 485 486 /* 487 * Firmware has an individual device recovery time typically 488 * of 35 seconds, give us a margin. Thor devices can take longer in 489 * error recovery, hence different value. 490 */ 491 if (set_timeout) { 492 timeout = aac->sa_firmware ? AAC_SA_TIMEOUT : AAC_ARC_TIMEOUT; 493 blk_queue_rq_timeout(sdev->request_queue, timeout * HZ); 494 } 495 496 if (depth > 256) 497 depth = 256; 498 else if (depth < 1) 499 depth = 1; 500 501 scsi_change_queue_depth(sdev, depth); 502 503 sdev->tagged_supported = 1; 504 505 return 0; 506 } 507 508 /** 509 * aac_change_queue_depth - alter queue depths 510 * @sdev: SCSI device we are considering 511 * @depth: desired queue depth 512 * 513 * Alters queue depths for target device based on the host adapter's 514 * total capacity and the queue depth supported by the target device. 515 */ 516 517 static int aac_change_queue_depth(struct scsi_device *sdev, int depth) 518 { 519 struct aac_dev *aac = (struct aac_dev *)(sdev->host->hostdata); 520 int chn, tid, is_native_device = 0; 521 522 chn = aac_logical_to_phys(sdev_channel(sdev)); 523 tid = sdev_id(sdev); 524 if (chn < AAC_MAX_BUSES && tid < AAC_MAX_TARGETS && 525 aac->hba_map[chn][tid].devtype == AAC_DEVTYPE_NATIVE_RAW) 526 is_native_device = 1; 527 528 if (sdev->tagged_supported && (sdev->type == TYPE_DISK) && 529 (sdev_channel(sdev) == CONTAINER_CHANNEL)) { 530 struct scsi_device * dev; 531 struct Scsi_Host *host = sdev->host; 532 unsigned num = 0; 533 534 __shost_for_each_device(dev, host) { 535 if (dev->tagged_supported && (dev->type == TYPE_DISK) && 536 (sdev_channel(dev) == CONTAINER_CHANNEL)) 537 ++num; 538 ++num; 539 } 540 if (num >= host->can_queue) 541 num = host->can_queue - 1; 542 if (depth > (host->can_queue - num)) 543 depth = host->can_queue - num; 544 if (depth > 256) 545 depth = 256; 546 else if (depth < 2) 547 depth = 2; 548 return scsi_change_queue_depth(sdev, depth); 549 } else if (is_native_device) { 550 scsi_change_queue_depth(sdev, aac->hba_map[chn][tid].qd_limit); 551 } else { 552 scsi_change_queue_depth(sdev, 1); 553 } 554 return sdev->queue_depth; 555 } 556 557 static ssize_t aac_show_raid_level(struct device *dev, struct device_attribute *attr, char *buf) 558 { 559 struct scsi_device *sdev = to_scsi_device(dev); 560 struct aac_dev *aac = (struct aac_dev *)(sdev->host->hostdata); 561 if (sdev_channel(sdev) != CONTAINER_CHANNEL) 562 return snprintf(buf, PAGE_SIZE, sdev->no_uld_attach 563 ? "Hidden\n" : 564 ((aac->jbod && (sdev->type == TYPE_DISK)) ? "JBOD\n" : "")); 565 return snprintf(buf, PAGE_SIZE, "%s\n", 566 get_container_type(aac->fsa_dev[sdev_id(sdev)].type)); 567 } 568 569 static struct device_attribute aac_raid_level_attr = { 570 .attr = { 571 .name = "level", 572 .mode = S_IRUGO, 573 }, 574 .show = aac_show_raid_level 575 }; 576 577 static ssize_t aac_show_unique_id(struct device *dev, 578 struct device_attribute *attr, char *buf) 579 { 580 struct scsi_device *sdev = to_scsi_device(dev); 581 struct aac_dev *aac = (struct aac_dev *)(sdev->host->hostdata); 582 unsigned char sn[16]; 583 584 memset(sn, 0, sizeof(sn)); 585 586 if (sdev_channel(sdev) == CONTAINER_CHANNEL) 587 memcpy(sn, aac->fsa_dev[sdev_id(sdev)].identifier, sizeof(sn)); 588 589 return snprintf(buf, 16 * 2 + 2, 590 "%02X%02X%02X%02X%02X%02X%02X%02X%02X%02X%02X%02X%02X%02X%02X%02X\n", 591 sn[0], sn[1], sn[2], sn[3], 592 sn[4], sn[5], sn[6], sn[7], 593 sn[8], sn[9], sn[10], sn[11], 594 sn[12], sn[13], sn[14], sn[15]); 595 } 596 597 static struct device_attribute aac_unique_id_attr = { 598 .attr = { 599 .name = "unique_id", 600 .mode = 0444, 601 }, 602 .show = aac_show_unique_id 603 }; 604 605 606 607 static struct attribute *aac_dev_attrs[] = { 608 &aac_raid_level_attr.attr, 609 &aac_unique_id_attr.attr, 610 NULL, 611 }; 612 613 ATTRIBUTE_GROUPS(aac_dev); 614 615 static int aac_ioctl(struct scsi_device *sdev, unsigned int cmd, 616 void __user *arg) 617 { 618 int retval; 619 struct aac_dev *dev = (struct aac_dev *)sdev->host->hostdata; 620 if (!capable(CAP_SYS_RAWIO)) 621 return -EPERM; 622 retval = aac_adapter_check_health(dev); 623 if (retval) 624 return -EBUSY; 625 return aac_do_ioctl(dev, cmd, arg); 626 } 627 628 struct fib_count_data { 629 int mlcnt; 630 int llcnt; 631 int ehcnt; 632 int fwcnt; 633 int krlcnt; 634 }; 635 636 static bool fib_count_iter(struct scsi_cmnd *scmnd, void *data, bool reserved) 637 { 638 struct fib_count_data *fib_count = data; 639 640 switch (aac_priv(scmnd)->owner) { 641 case AAC_OWNER_FIRMWARE: 642 fib_count->fwcnt++; 643 break; 644 case AAC_OWNER_ERROR_HANDLER: 645 fib_count->ehcnt++; 646 break; 647 case AAC_OWNER_LOWLEVEL: 648 fib_count->llcnt++; 649 break; 650 case AAC_OWNER_MIDLEVEL: 651 fib_count->mlcnt++; 652 break; 653 default: 654 fib_count->krlcnt++; 655 break; 656 } 657 return true; 658 } 659 660 /* Called during SCSI EH, so we don't need to block requests */ 661 static int get_num_of_incomplete_fibs(struct aac_dev *aac) 662 { 663 struct Scsi_Host *shost = aac->scsi_host_ptr; 664 struct device *ctrl_dev; 665 struct fib_count_data fcnt = { }; 666 667 scsi_host_busy_iter(shost, fib_count_iter, &fcnt); 668 669 ctrl_dev = &aac->pdev->dev; 670 671 dev_info(ctrl_dev, "outstanding cmd: midlevel-%d\n", fcnt.mlcnt); 672 dev_info(ctrl_dev, "outstanding cmd: lowlevel-%d\n", fcnt.llcnt); 673 dev_info(ctrl_dev, "outstanding cmd: error handler-%d\n", fcnt.ehcnt); 674 dev_info(ctrl_dev, "outstanding cmd: firmware-%d\n", fcnt.fwcnt); 675 dev_info(ctrl_dev, "outstanding cmd: kernel-%d\n", fcnt.krlcnt); 676 677 return fcnt.mlcnt + fcnt.llcnt + fcnt.ehcnt + fcnt.fwcnt; 678 } 679 680 static int aac_eh_abort(struct scsi_cmnd* cmd) 681 { 682 struct aac_cmd_priv *cmd_priv = aac_priv(cmd); 683 struct scsi_device * dev = cmd->device; 684 struct Scsi_Host * host = dev->host; 685 struct aac_dev * aac = (struct aac_dev *)host->hostdata; 686 int count, found; 687 u32 bus, cid; 688 int ret = FAILED; 689 690 if (aac_adapter_check_health(aac)) 691 return ret; 692 693 bus = aac_logical_to_phys(scmd_channel(cmd)); 694 cid = scmd_id(cmd); 695 if (aac->hba_map[bus][cid].devtype == AAC_DEVTYPE_NATIVE_RAW) { 696 struct fib *fib; 697 struct aac_hba_tm_req *tmf; 698 int status; 699 u64 address; 700 701 pr_err("%s: Host adapter abort request (%d,%d,%d,%d)\n", 702 AAC_DRIVERNAME, 703 host->host_no, sdev_channel(dev), sdev_id(dev), (int)dev->lun); 704 705 found = 0; 706 for (count = 0; count < (host->can_queue + AAC_NUM_MGT_FIB); ++count) { 707 fib = &aac->fibs[count]; 708 if (*(u8 *)fib->hw_fib_va != 0 && 709 (fib->flags & FIB_CONTEXT_FLAG_NATIVE_HBA) && 710 (fib->callback_data == cmd)) { 711 found = 1; 712 break; 713 } 714 } 715 if (!found) 716 return ret; 717 718 /* start a HBA_TMF_ABORT_TASK TMF request */ 719 fib = aac_fib_alloc(aac); 720 if (!fib) 721 return ret; 722 723 tmf = (struct aac_hba_tm_req *)fib->hw_fib_va; 724 memset(tmf, 0, sizeof(*tmf)); 725 tmf->tmf = HBA_TMF_ABORT_TASK; 726 tmf->it_nexus = aac->hba_map[bus][cid].rmw_nexus; 727 tmf->lun[1] = cmd->device->lun; 728 729 address = (u64)fib->hw_error_pa; 730 tmf->error_ptr_hi = cpu_to_le32((u32)(address >> 32)); 731 tmf->error_ptr_lo = cpu_to_le32((u32)(address & 0xffffffff)); 732 tmf->error_length = cpu_to_le32(FW_ERROR_BUFFER_SIZE); 733 734 fib->hbacmd_size = sizeof(*tmf); 735 cmd_priv->sent_command = 0; 736 737 status = aac_hba_send(HBA_IU_TYPE_SCSI_TM_REQ, fib, 738 (fib_callback) aac_hba_callback, 739 (void *) cmd); 740 if (status != -EINPROGRESS) { 741 aac_fib_complete(fib); 742 aac_fib_free(fib); 743 return ret; 744 } 745 /* Wait up to 15 secs for completion */ 746 for (count = 0; count < 15; ++count) { 747 if (cmd_priv->sent_command) { 748 ret = SUCCESS; 749 break; 750 } 751 msleep(1000); 752 } 753 754 if (ret != SUCCESS) 755 pr_err("%s: Host adapter abort request timed out\n", 756 AAC_DRIVERNAME); 757 } else { 758 pr_err( 759 "%s: Host adapter abort request.\n" 760 "%s: Outstanding commands on (%d,%d,%d,%d):\n", 761 AAC_DRIVERNAME, AAC_DRIVERNAME, 762 host->host_no, sdev_channel(dev), sdev_id(dev), 763 (int)dev->lun); 764 switch (cmd->cmnd[0]) { 765 case SERVICE_ACTION_IN_16: 766 if (!(aac->raw_io_interface) || 767 !(aac->raw_io_64) || 768 ((cmd->cmnd[1] & 0x1f) != SAI_READ_CAPACITY_16)) 769 break; 770 fallthrough; 771 case INQUIRY: 772 case READ_CAPACITY: 773 /* 774 * Mark associated FIB to not complete, 775 * eh handler does this 776 */ 777 for (count = 0; 778 count < (host->can_queue + AAC_NUM_MGT_FIB); 779 ++count) { 780 struct fib *fib = &aac->fibs[count]; 781 782 if (fib->hw_fib_va->header.XferState && 783 (fib->flags & FIB_CONTEXT_FLAG) && 784 (fib->callback_data == cmd)) { 785 fib->flags |= 786 FIB_CONTEXT_FLAG_TIMED_OUT; 787 cmd_priv->owner = 788 AAC_OWNER_ERROR_HANDLER; 789 ret = SUCCESS; 790 } 791 } 792 break; 793 case TEST_UNIT_READY: 794 /* 795 * Mark associated FIB to not complete, 796 * eh handler does this 797 */ 798 for (count = 0; 799 count < (host->can_queue + AAC_NUM_MGT_FIB); 800 ++count) { 801 struct scsi_cmnd *command; 802 struct fib *fib = &aac->fibs[count]; 803 804 command = fib->callback_data; 805 806 if ((fib->hw_fib_va->header.XferState & 807 cpu_to_le32 808 (Async | NoResponseExpected)) && 809 (fib->flags & FIB_CONTEXT_FLAG) && 810 ((command)) && 811 (command->device == cmd->device)) { 812 fib->flags |= 813 FIB_CONTEXT_FLAG_TIMED_OUT; 814 aac_priv(command)->owner = 815 AAC_OWNER_ERROR_HANDLER; 816 if (command == cmd) 817 ret = SUCCESS; 818 } 819 } 820 break; 821 } 822 } 823 return ret; 824 } 825 826 static u8 aac_eh_tmf_lun_reset_fib(struct aac_hba_map_info *info, 827 struct fib *fib, u64 tmf_lun) 828 { 829 struct aac_hba_tm_req *tmf; 830 u64 address; 831 832 /* start a HBA_TMF_LUN_RESET TMF request */ 833 tmf = (struct aac_hba_tm_req *)fib->hw_fib_va; 834 memset(tmf, 0, sizeof(*tmf)); 835 tmf->tmf = HBA_TMF_LUN_RESET; 836 tmf->it_nexus = info->rmw_nexus; 837 int_to_scsilun(tmf_lun, (struct scsi_lun *)tmf->lun); 838 839 address = (u64)fib->hw_error_pa; 840 tmf->error_ptr_hi = cpu_to_le32 841 ((u32)(address >> 32)); 842 tmf->error_ptr_lo = cpu_to_le32 843 ((u32)(address & 0xffffffff)); 844 tmf->error_length = cpu_to_le32(FW_ERROR_BUFFER_SIZE); 845 fib->hbacmd_size = sizeof(*tmf); 846 847 return HBA_IU_TYPE_SCSI_TM_REQ; 848 } 849 850 static u8 aac_eh_tmf_hard_reset_fib(struct aac_hba_map_info *info, 851 struct fib *fib) 852 { 853 struct aac_hba_reset_req *rst; 854 u64 address; 855 856 /* already tried, start a hard reset now */ 857 rst = (struct aac_hba_reset_req *)fib->hw_fib_va; 858 memset(rst, 0, sizeof(*rst)); 859 rst->it_nexus = info->rmw_nexus; 860 861 address = (u64)fib->hw_error_pa; 862 rst->error_ptr_hi = cpu_to_le32((u32)(address >> 32)); 863 rst->error_ptr_lo = cpu_to_le32((u32)(address & 0xffffffff)); 864 rst->error_length = cpu_to_le32(FW_ERROR_BUFFER_SIZE); 865 fib->hbacmd_size = sizeof(*rst); 866 867 return HBA_IU_TYPE_SATA_REQ; 868 } 869 870 static void aac_tmf_callback(void *context, struct fib *fibptr) 871 { 872 struct aac_hba_resp *err = 873 &((struct aac_native_hba *)fibptr->hw_fib_va)->resp.err; 874 struct aac_hba_map_info *info = context; 875 int res; 876 877 switch (err->service_response) { 878 case HBA_RESP_SVCRES_TMF_REJECTED: 879 res = -1; 880 break; 881 case HBA_RESP_SVCRES_TMF_LUN_INVALID: 882 res = 0; 883 break; 884 case HBA_RESP_SVCRES_TMF_COMPLETE: 885 case HBA_RESP_SVCRES_TMF_SUCCEEDED: 886 res = 0; 887 break; 888 default: 889 res = -2; 890 break; 891 } 892 aac_fib_complete(fibptr); 893 894 info->reset_state = res; 895 } 896 897 /* 898 * aac_eh_dev_reset - Device reset command handling 899 * @scsi_cmd: SCSI command block causing the reset 900 * 901 */ 902 static int aac_eh_dev_reset(struct scsi_cmnd *cmd) 903 { 904 struct scsi_device * dev = cmd->device; 905 struct Scsi_Host * host = dev->host; 906 struct aac_dev * aac = (struct aac_dev *)host->hostdata; 907 struct aac_hba_map_info *info; 908 int count; 909 u32 bus, cid; 910 struct fib *fib; 911 int ret = FAILED; 912 int status; 913 u8 command; 914 915 bus = aac_logical_to_phys(scmd_channel(cmd)); 916 cid = scmd_id(cmd); 917 918 if (bus >= AAC_MAX_BUSES || cid >= AAC_MAX_TARGETS) 919 return FAILED; 920 921 info = &aac->hba_map[bus][cid]; 922 923 if (!(info->devtype == AAC_DEVTYPE_NATIVE_RAW && 924 !(info->reset_state > 0))) 925 return FAILED; 926 927 pr_err("%s: Host device reset request. SCSI hang ?\n", 928 AAC_DRIVERNAME); 929 930 fib = aac_fib_alloc(aac); 931 if (!fib) 932 return ret; 933 934 /* start a HBA_TMF_LUN_RESET TMF request */ 935 command = aac_eh_tmf_lun_reset_fib(info, fib, dev->lun); 936 937 info->reset_state = 1; 938 939 status = aac_hba_send(command, fib, 940 (fib_callback) aac_tmf_callback, 941 (void *) info); 942 if (status != -EINPROGRESS) { 943 info->reset_state = 0; 944 aac_fib_complete(fib); 945 aac_fib_free(fib); 946 return ret; 947 } 948 /* Wait up to 15 seconds for completion */ 949 for (count = 0; count < 15; ++count) { 950 if (info->reset_state == 0) { 951 ret = info->reset_state == 0 ? SUCCESS : FAILED; 952 break; 953 } 954 msleep(1000); 955 } 956 957 return ret; 958 } 959 960 /* 961 * aac_eh_target_reset - Target reset command handling 962 * @scsi_cmd: SCSI command block causing the reset 963 * 964 */ 965 static int aac_eh_target_reset(struct scsi_cmnd *cmd) 966 { 967 struct scsi_device * dev = cmd->device; 968 struct Scsi_Host * host = dev->host; 969 struct aac_dev * aac = (struct aac_dev *)host->hostdata; 970 struct aac_hba_map_info *info; 971 int count; 972 u32 bus, cid; 973 int ret = FAILED; 974 struct fib *fib; 975 int status; 976 u8 command; 977 978 bus = aac_logical_to_phys(scmd_channel(cmd)); 979 cid = scmd_id(cmd); 980 981 if (bus >= AAC_MAX_BUSES || cid >= AAC_MAX_TARGETS) 982 return FAILED; 983 984 info = &aac->hba_map[bus][cid]; 985 986 if (!(info->devtype == AAC_DEVTYPE_NATIVE_RAW && 987 !(info->reset_state > 0))) 988 return FAILED; 989 990 pr_err("%s: Host target reset request. SCSI hang ?\n", 991 AAC_DRIVERNAME); 992 993 fib = aac_fib_alloc(aac); 994 if (!fib) 995 return ret; 996 997 998 /* already tried, start a hard reset now */ 999 command = aac_eh_tmf_hard_reset_fib(info, fib); 1000 1001 info->reset_state = 2; 1002 1003 status = aac_hba_send(command, fib, 1004 (fib_callback) aac_tmf_callback, 1005 (void *) info); 1006 1007 if (status != -EINPROGRESS) { 1008 info->reset_state = 0; 1009 aac_fib_complete(fib); 1010 aac_fib_free(fib); 1011 return ret; 1012 } 1013 1014 /* Wait up to 15 seconds for completion */ 1015 for (count = 0; count < 15; ++count) { 1016 if (info->reset_state <= 0) { 1017 ret = info->reset_state == 0 ? SUCCESS : FAILED; 1018 break; 1019 } 1020 msleep(1000); 1021 } 1022 1023 return ret; 1024 } 1025 1026 /* 1027 * aac_eh_bus_reset - Bus reset command handling 1028 * @scsi_cmd: SCSI command block causing the reset 1029 * 1030 */ 1031 static int aac_eh_bus_reset(struct scsi_cmnd* cmd) 1032 { 1033 struct scsi_device * dev = cmd->device; 1034 struct Scsi_Host * host = dev->host; 1035 struct aac_dev * aac = (struct aac_dev *)host->hostdata; 1036 int count; 1037 u32 cmd_bus; 1038 int status = 0; 1039 1040 1041 cmd_bus = aac_logical_to_phys(scmd_channel(cmd)); 1042 /* Mark the assoc. FIB to not complete, eh handler does this */ 1043 for (count = 0; count < (host->can_queue + AAC_NUM_MGT_FIB); ++count) { 1044 struct fib *fib = &aac->fibs[count]; 1045 1046 if (fib->hw_fib_va->header.XferState && 1047 (fib->flags & FIB_CONTEXT_FLAG) && 1048 (fib->flags & FIB_CONTEXT_FLAG_SCSI_CMD)) { 1049 struct aac_hba_map_info *info; 1050 u32 bus, cid; 1051 1052 cmd = (struct scsi_cmnd *)fib->callback_data; 1053 bus = aac_logical_to_phys(scmd_channel(cmd)); 1054 if (bus != cmd_bus) 1055 continue; 1056 cid = scmd_id(cmd); 1057 info = &aac->hba_map[bus][cid]; 1058 if (bus >= AAC_MAX_BUSES || cid >= AAC_MAX_TARGETS || 1059 info->devtype != AAC_DEVTYPE_NATIVE_RAW) { 1060 fib->flags |= FIB_CONTEXT_FLAG_EH_RESET; 1061 aac_priv(cmd)->owner = AAC_OWNER_ERROR_HANDLER; 1062 } 1063 } 1064 } 1065 1066 pr_err("%s: Host bus reset request. SCSI hang ?\n", AAC_DRIVERNAME); 1067 1068 /* 1069 * Check the health of the controller 1070 */ 1071 status = aac_adapter_check_health(aac); 1072 if (status) 1073 dev_err(&aac->pdev->dev, "Adapter health - %d\n", status); 1074 1075 count = get_num_of_incomplete_fibs(aac); 1076 return (count == 0) ? SUCCESS : FAILED; 1077 } 1078 1079 /* 1080 * aac_eh_host_reset - Host reset command handling 1081 * @scsi_cmd: SCSI command block causing the reset 1082 * 1083 */ 1084 static int aac_eh_host_reset(struct scsi_cmnd *cmd) 1085 { 1086 struct scsi_device * dev = cmd->device; 1087 struct Scsi_Host * host = dev->host; 1088 struct aac_dev * aac = (struct aac_dev *)host->hostdata; 1089 int ret = FAILED; 1090 __le32 supported_options2 = 0; 1091 bool is_mu_reset; 1092 bool is_ignore_reset; 1093 bool is_doorbell_reset; 1094 1095 /* 1096 * Check if reset is supported by the firmware 1097 */ 1098 supported_options2 = aac->supplement_adapter_info.supported_options2; 1099 is_mu_reset = supported_options2 & AAC_OPTION_MU_RESET; 1100 is_doorbell_reset = supported_options2 & AAC_OPTION_DOORBELL_RESET; 1101 is_ignore_reset = supported_options2 & AAC_OPTION_IGNORE_RESET; 1102 /* 1103 * This adapter needs a blind reset, only do so for 1104 * Adapters that support a register, instead of a commanded, 1105 * reset. 1106 */ 1107 if ((is_mu_reset || is_doorbell_reset) 1108 && aac_check_reset 1109 && (aac_check_reset != -1 || !is_ignore_reset)) { 1110 /* Bypass wait for command quiesce */ 1111 if (aac_reset_adapter(aac, 2, IOP_HWSOFT_RESET) == 0) 1112 ret = SUCCESS; 1113 } 1114 /* 1115 * Reset EH state 1116 */ 1117 if (ret == SUCCESS) { 1118 int bus, cid; 1119 struct aac_hba_map_info *info; 1120 1121 for (bus = 0; bus < AAC_MAX_BUSES; bus++) { 1122 for (cid = 0; cid < AAC_MAX_TARGETS; cid++) { 1123 info = &aac->hba_map[bus][cid]; 1124 if (info->devtype == AAC_DEVTYPE_NATIVE_RAW) 1125 info->reset_state = 0; 1126 } 1127 } 1128 } 1129 return ret; 1130 } 1131 1132 /** 1133 * aac_cfg_open - open a configuration file 1134 * @inode: inode being opened 1135 * @file: file handle attached 1136 * 1137 * Called when the configuration device is opened. Does the needed 1138 * set up on the handle and then returns 1139 * 1140 * Bugs: This needs extending to check a given adapter is present 1141 * so we can support hot plugging, and to ref count adapters. 1142 */ 1143 1144 static int aac_cfg_open(struct inode *inode, struct file *file) 1145 { 1146 struct aac_dev *aac; 1147 unsigned minor_number = iminor(inode); 1148 int err = -ENODEV; 1149 1150 mutex_lock(&aac_mutex); /* BKL pushdown: nothing else protects this list */ 1151 list_for_each_entry(aac, &aac_devices, entry) { 1152 if (aac->id == minor_number) { 1153 file->private_data = aac; 1154 err = 0; 1155 break; 1156 } 1157 } 1158 mutex_unlock(&aac_mutex); 1159 1160 return err; 1161 } 1162 1163 /** 1164 * aac_cfg_ioctl - AAC configuration request 1165 * @file: file handle 1166 * @cmd: ioctl command code 1167 * @arg: argument 1168 * 1169 * Handles a configuration ioctl. Currently this involves wrapping it 1170 * up and feeding it into the nasty windowsalike glue layer. 1171 * 1172 * Bugs: Needs locking against parallel ioctls lower down 1173 * Bugs: Needs to handle hot plugging 1174 */ 1175 1176 static long aac_cfg_ioctl(struct file *file, 1177 unsigned int cmd, unsigned long arg) 1178 { 1179 struct aac_dev *aac = (struct aac_dev *)file->private_data; 1180 1181 if (!capable(CAP_SYS_RAWIO)) 1182 return -EPERM; 1183 1184 return aac_do_ioctl(aac, cmd, (void __user *)arg); 1185 } 1186 1187 static ssize_t aac_show_model(struct device *device, 1188 struct device_attribute *attr, char *buf) 1189 { 1190 struct aac_dev *dev = (struct aac_dev*)class_to_shost(device)->hostdata; 1191 int len; 1192 1193 if (dev->supplement_adapter_info.adapter_type_text[0]) { 1194 char *cp = dev->supplement_adapter_info.adapter_type_text; 1195 while (*cp && *cp != ' ') 1196 ++cp; 1197 while (*cp == ' ') 1198 ++cp; 1199 len = snprintf(buf, PAGE_SIZE, "%s\n", cp); 1200 } else 1201 len = snprintf(buf, PAGE_SIZE, "%s\n", 1202 aac_drivers[dev->cardtype].model); 1203 return len; 1204 } 1205 1206 static ssize_t aac_show_vendor(struct device *device, 1207 struct device_attribute *attr, char *buf) 1208 { 1209 struct aac_dev *dev = (struct aac_dev*)class_to_shost(device)->hostdata; 1210 struct aac_supplement_adapter_info *sup_adap_info; 1211 int len; 1212 1213 sup_adap_info = &dev->supplement_adapter_info; 1214 if (sup_adap_info->adapter_type_text[0]) { 1215 char *cp = sup_adap_info->adapter_type_text; 1216 while (*cp && *cp != ' ') 1217 ++cp; 1218 len = snprintf(buf, PAGE_SIZE, "%.*s\n", 1219 (int)(cp - (char *)sup_adap_info->adapter_type_text), 1220 sup_adap_info->adapter_type_text); 1221 } else 1222 len = snprintf(buf, PAGE_SIZE, "%s\n", 1223 aac_drivers[dev->cardtype].vname); 1224 return len; 1225 } 1226 1227 static ssize_t aac_show_flags(struct device *cdev, 1228 struct device_attribute *attr, char *buf) 1229 { 1230 int len = 0; 1231 struct aac_dev *dev = (struct aac_dev*)class_to_shost(cdev)->hostdata; 1232 1233 if (nblank(dprintk(x))) 1234 len = snprintf(buf, PAGE_SIZE, "dprintk\n"); 1235 #ifdef AAC_DETAILED_STATUS_INFO 1236 len += scnprintf(buf + len, PAGE_SIZE - len, 1237 "AAC_DETAILED_STATUS_INFO\n"); 1238 #endif 1239 if (dev->raw_io_interface && dev->raw_io_64) 1240 len += scnprintf(buf + len, PAGE_SIZE - len, 1241 "SAI_READ_CAPACITY_16\n"); 1242 if (dev->jbod) 1243 len += scnprintf(buf + len, PAGE_SIZE - len, 1244 "SUPPORTED_JBOD\n"); 1245 if (dev->supplement_adapter_info.supported_options2 & 1246 AAC_OPTION_POWER_MANAGEMENT) 1247 len += scnprintf(buf + len, PAGE_SIZE - len, 1248 "SUPPORTED_POWER_MANAGEMENT\n"); 1249 if (dev->msi) 1250 len += scnprintf(buf + len, PAGE_SIZE - len, "PCI_HAS_MSI\n"); 1251 return len; 1252 } 1253 1254 static ssize_t aac_show_kernel_version(struct device *device, 1255 struct device_attribute *attr, 1256 char *buf) 1257 { 1258 struct aac_dev *dev = (struct aac_dev*)class_to_shost(device)->hostdata; 1259 int len, tmp; 1260 1261 tmp = le32_to_cpu(dev->adapter_info.kernelrev); 1262 len = snprintf(buf, PAGE_SIZE, "%d.%d-%d[%d]\n", 1263 tmp >> 24, (tmp >> 16) & 0xff, tmp & 0xff, 1264 le32_to_cpu(dev->adapter_info.kernelbuild)); 1265 return len; 1266 } 1267 1268 static ssize_t aac_show_monitor_version(struct device *device, 1269 struct device_attribute *attr, 1270 char *buf) 1271 { 1272 struct aac_dev *dev = (struct aac_dev*)class_to_shost(device)->hostdata; 1273 int len, tmp; 1274 1275 tmp = le32_to_cpu(dev->adapter_info.monitorrev); 1276 len = snprintf(buf, PAGE_SIZE, "%d.%d-%d[%d]\n", 1277 tmp >> 24, (tmp >> 16) & 0xff, tmp & 0xff, 1278 le32_to_cpu(dev->adapter_info.monitorbuild)); 1279 return len; 1280 } 1281 1282 static ssize_t aac_show_bios_version(struct device *device, 1283 struct device_attribute *attr, 1284 char *buf) 1285 { 1286 struct aac_dev *dev = (struct aac_dev*)class_to_shost(device)->hostdata; 1287 int len, tmp; 1288 1289 tmp = le32_to_cpu(dev->adapter_info.biosrev); 1290 len = snprintf(buf, PAGE_SIZE, "%d.%d-%d[%d]\n", 1291 tmp >> 24, (tmp >> 16) & 0xff, tmp & 0xff, 1292 le32_to_cpu(dev->adapter_info.biosbuild)); 1293 return len; 1294 } 1295 1296 static ssize_t aac_show_driver_version(struct device *device, 1297 struct device_attribute *attr, 1298 char *buf) 1299 { 1300 return snprintf(buf, PAGE_SIZE, "%s\n", aac_driver_version); 1301 } 1302 1303 static ssize_t aac_show_serial_number(struct device *device, 1304 struct device_attribute *attr, char *buf) 1305 { 1306 struct aac_dev *dev = (struct aac_dev*)class_to_shost(device)->hostdata; 1307 int len = 0; 1308 1309 if (le32_to_cpu(dev->adapter_info.serial[0]) != 0xBAD0) 1310 len = snprintf(buf, 16, "%06X\n", 1311 le32_to_cpu(dev->adapter_info.serial[0])); 1312 if (len && 1313 !memcmp(&dev->supplement_adapter_info.mfg_pcba_serial_no[ 1314 sizeof(dev->supplement_adapter_info.mfg_pcba_serial_no)-len], 1315 buf, len-1)) 1316 len = snprintf(buf, 16, "%.*s\n", 1317 (int)sizeof(dev->supplement_adapter_info.mfg_pcba_serial_no), 1318 dev->supplement_adapter_info.mfg_pcba_serial_no); 1319 1320 return min(len, 16); 1321 } 1322 1323 static ssize_t aac_show_max_channel(struct device *device, 1324 struct device_attribute *attr, char *buf) 1325 { 1326 return snprintf(buf, PAGE_SIZE, "%d\n", 1327 class_to_shost(device)->max_channel); 1328 } 1329 1330 static ssize_t aac_show_max_id(struct device *device, 1331 struct device_attribute *attr, char *buf) 1332 { 1333 return snprintf(buf, PAGE_SIZE, "%d\n", 1334 class_to_shost(device)->max_id); 1335 } 1336 1337 static ssize_t aac_store_reset_adapter(struct device *device, 1338 struct device_attribute *attr, 1339 const char *buf, size_t count) 1340 { 1341 int retval = -EACCES; 1342 1343 if (!capable(CAP_SYS_ADMIN)) 1344 return retval; 1345 1346 retval = aac_reset_adapter(shost_priv(class_to_shost(device)), 1347 buf[0] == '!', IOP_HWSOFT_RESET); 1348 if (retval >= 0) 1349 retval = count; 1350 1351 return retval; 1352 } 1353 1354 static ssize_t aac_show_reset_adapter(struct device *device, 1355 struct device_attribute *attr, 1356 char *buf) 1357 { 1358 struct aac_dev *dev = (struct aac_dev*)class_to_shost(device)->hostdata; 1359 int len, tmp; 1360 1361 tmp = aac_adapter_check_health(dev); 1362 if ((tmp == 0) && dev->in_reset) 1363 tmp = -EBUSY; 1364 len = snprintf(buf, PAGE_SIZE, "0x%x\n", tmp); 1365 return len; 1366 } 1367 1368 static struct device_attribute aac_model = { 1369 .attr = { 1370 .name = "model", 1371 .mode = S_IRUGO, 1372 }, 1373 .show = aac_show_model, 1374 }; 1375 static struct device_attribute aac_vendor = { 1376 .attr = { 1377 .name = "vendor", 1378 .mode = S_IRUGO, 1379 }, 1380 .show = aac_show_vendor, 1381 }; 1382 static struct device_attribute aac_flags = { 1383 .attr = { 1384 .name = "flags", 1385 .mode = S_IRUGO, 1386 }, 1387 .show = aac_show_flags, 1388 }; 1389 static struct device_attribute aac_kernel_version = { 1390 .attr = { 1391 .name = "hba_kernel_version", 1392 .mode = S_IRUGO, 1393 }, 1394 .show = aac_show_kernel_version, 1395 }; 1396 static struct device_attribute aac_monitor_version = { 1397 .attr = { 1398 .name = "hba_monitor_version", 1399 .mode = S_IRUGO, 1400 }, 1401 .show = aac_show_monitor_version, 1402 }; 1403 static struct device_attribute aac_bios_version = { 1404 .attr = { 1405 .name = "hba_bios_version", 1406 .mode = S_IRUGO, 1407 }, 1408 .show = aac_show_bios_version, 1409 }; 1410 static struct device_attribute aac_lld_version = { 1411 .attr = { 1412 .name = "driver_version", 1413 .mode = 0444, 1414 }, 1415 .show = aac_show_driver_version, 1416 }; 1417 static struct device_attribute aac_serial_number = { 1418 .attr = { 1419 .name = "serial_number", 1420 .mode = S_IRUGO, 1421 }, 1422 .show = aac_show_serial_number, 1423 }; 1424 static struct device_attribute aac_max_channel = { 1425 .attr = { 1426 .name = "max_channel", 1427 .mode = S_IRUGO, 1428 }, 1429 .show = aac_show_max_channel, 1430 }; 1431 static struct device_attribute aac_max_id = { 1432 .attr = { 1433 .name = "max_id", 1434 .mode = S_IRUGO, 1435 }, 1436 .show = aac_show_max_id, 1437 }; 1438 static struct device_attribute aac_reset = { 1439 .attr = { 1440 .name = "reset_host", 1441 .mode = S_IWUSR|S_IRUGO, 1442 }, 1443 .store = aac_store_reset_adapter, 1444 .show = aac_show_reset_adapter, 1445 }; 1446 1447 static struct attribute *aac_host_attrs[] = { 1448 &aac_model.attr, 1449 &aac_vendor.attr, 1450 &aac_flags.attr, 1451 &aac_kernel_version.attr, 1452 &aac_monitor_version.attr, 1453 &aac_bios_version.attr, 1454 &aac_lld_version.attr, 1455 &aac_serial_number.attr, 1456 &aac_max_channel.attr, 1457 &aac_max_id.attr, 1458 &aac_reset.attr, 1459 NULL 1460 }; 1461 1462 ATTRIBUTE_GROUPS(aac_host); 1463 1464 ssize_t aac_get_serial_number(struct device *device, char *buf) 1465 { 1466 return aac_show_serial_number(device, &aac_serial_number, buf); 1467 } 1468 1469 static const struct file_operations aac_cfg_fops = { 1470 .owner = THIS_MODULE, 1471 .unlocked_ioctl = aac_cfg_ioctl, 1472 #ifdef CONFIG_COMPAT 1473 .compat_ioctl = aac_cfg_ioctl, 1474 #endif 1475 .open = aac_cfg_open, 1476 .llseek = noop_llseek, 1477 }; 1478 1479 static struct scsi_host_template aac_driver_template = { 1480 .module = THIS_MODULE, 1481 .name = "AAC", 1482 .proc_name = AAC_DRIVERNAME, 1483 .info = aac_info, 1484 .ioctl = aac_ioctl, 1485 #ifdef CONFIG_COMPAT 1486 .compat_ioctl = aac_ioctl, 1487 #endif 1488 .queuecommand = aac_queuecommand, 1489 .bios_param = aac_biosparm, 1490 .shost_groups = aac_host_groups, 1491 .slave_configure = aac_slave_configure, 1492 .change_queue_depth = aac_change_queue_depth, 1493 .sdev_groups = aac_dev_groups, 1494 .eh_abort_handler = aac_eh_abort, 1495 .eh_device_reset_handler = aac_eh_dev_reset, 1496 .eh_target_reset_handler = aac_eh_target_reset, 1497 .eh_bus_reset_handler = aac_eh_bus_reset, 1498 .eh_host_reset_handler = aac_eh_host_reset, 1499 .can_queue = AAC_NUM_IO_FIB, 1500 .this_id = MAXIMUM_NUM_CONTAINERS, 1501 .sg_tablesize = 16, 1502 .max_sectors = 128, 1503 #if (AAC_NUM_IO_FIB > 256) 1504 .cmd_per_lun = 256, 1505 #else 1506 .cmd_per_lun = AAC_NUM_IO_FIB, 1507 #endif 1508 .emulated = 1, 1509 .no_write_same = 1, 1510 .cmd_size = sizeof(struct aac_cmd_priv), 1511 }; 1512 1513 static void __aac_shutdown(struct aac_dev * aac) 1514 { 1515 int i; 1516 1517 mutex_lock(&aac->ioctl_mutex); 1518 aac->adapter_shutdown = 1; 1519 mutex_unlock(&aac->ioctl_mutex); 1520 1521 if (aac->aif_thread) { 1522 int i; 1523 /* Clear out events first */ 1524 for (i = 0; i < (aac->scsi_host_ptr->can_queue + AAC_NUM_MGT_FIB); i++) { 1525 struct fib *fib = &aac->fibs[i]; 1526 if (!(fib->hw_fib_va->header.XferState & cpu_to_le32(NoResponseExpected | Async)) && 1527 (fib->hw_fib_va->header.XferState & cpu_to_le32(ResponseExpected))) 1528 complete(&fib->event_wait); 1529 } 1530 kthread_stop(aac->thread); 1531 aac->thread = NULL; 1532 } 1533 1534 aac_send_shutdown(aac); 1535 1536 aac_adapter_disable_int(aac); 1537 1538 if (aac_is_src(aac)) { 1539 if (aac->max_msix > 1) { 1540 for (i = 0; i < aac->max_msix; i++) { 1541 free_irq(pci_irq_vector(aac->pdev, i), 1542 &(aac->aac_msix[i])); 1543 } 1544 } else { 1545 free_irq(aac->pdev->irq, 1546 &(aac->aac_msix[0])); 1547 } 1548 } else { 1549 free_irq(aac->pdev->irq, aac); 1550 } 1551 if (aac->msi) 1552 pci_disable_msi(aac->pdev); 1553 else if (aac->max_msix > 1) 1554 pci_disable_msix(aac->pdev); 1555 } 1556 static void aac_init_char(void) 1557 { 1558 aac_cfg_major = register_chrdev(0, "aac", &aac_cfg_fops); 1559 if (aac_cfg_major < 0) { 1560 pr_err("aacraid: unable to register \"aac\" device.\n"); 1561 } 1562 } 1563 1564 void aac_reinit_aif(struct aac_dev *aac, unsigned int index) 1565 { 1566 /* 1567 * Firmware may send a AIF messages very early and the Driver may have 1568 * ignored as it is not fully ready to process the messages. Send 1569 * AIF to firmware so that if there are any unprocessed events they 1570 * can be processed now. 1571 */ 1572 if (aac_drivers[index].quirks & AAC_QUIRK_SRC) 1573 aac_intr_normal(aac, 0, 2, 0, NULL); 1574 1575 } 1576 1577 static int aac_probe_one(struct pci_dev *pdev, const struct pci_device_id *id) 1578 { 1579 unsigned index = id->driver_data; 1580 struct Scsi_Host *shost; 1581 struct aac_dev *aac; 1582 struct list_head *insert = &aac_devices; 1583 int error; 1584 int unique_id = 0; 1585 u64 dmamask; 1586 int mask_bits = 0; 1587 extern int aac_sync_mode; 1588 1589 /* 1590 * Only series 7 needs freset. 1591 */ 1592 if (pdev->device == PMC_DEVICE_S7) 1593 pdev->needs_freset = 1; 1594 1595 list_for_each_entry(aac, &aac_devices, entry) { 1596 if (aac->id > unique_id) 1597 break; 1598 insert = &aac->entry; 1599 unique_id++; 1600 } 1601 1602 pci_disable_link_state(pdev, PCIE_LINK_STATE_L0S | PCIE_LINK_STATE_L1 | 1603 PCIE_LINK_STATE_CLKPM); 1604 1605 error = pci_enable_device(pdev); 1606 if (error) 1607 goto out; 1608 1609 if (!(aac_drivers[index].quirks & AAC_QUIRK_SRC)) { 1610 error = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32)); 1611 if (error) { 1612 dev_err(&pdev->dev, "PCI 32 BIT dma mask set failed"); 1613 goto out_disable_pdev; 1614 } 1615 } 1616 1617 /* 1618 * If the quirk31 bit is set, the adapter needs adapter 1619 * to driver communication memory to be allocated below 2gig 1620 */ 1621 if (aac_drivers[index].quirks & AAC_QUIRK_31BIT) { 1622 dmamask = DMA_BIT_MASK(31); 1623 mask_bits = 31; 1624 } else { 1625 dmamask = DMA_BIT_MASK(32); 1626 mask_bits = 32; 1627 } 1628 1629 error = dma_set_coherent_mask(&pdev->dev, dmamask); 1630 if (error) { 1631 dev_err(&pdev->dev, "PCI %d B consistent dma mask set failed\n" 1632 , mask_bits); 1633 goto out_disable_pdev; 1634 } 1635 1636 pci_set_master(pdev); 1637 1638 shost = scsi_host_alloc(&aac_driver_template, sizeof(struct aac_dev)); 1639 if (!shost) { 1640 error = -ENOMEM; 1641 goto out_disable_pdev; 1642 } 1643 1644 shost->irq = pdev->irq; 1645 shost->unique_id = unique_id; 1646 shost->max_cmd_len = 16; 1647 1648 if (aac_cfg_major == AAC_CHARDEV_NEEDS_REINIT) 1649 aac_init_char(); 1650 1651 aac = (struct aac_dev *)shost->hostdata; 1652 aac->base_start = pci_resource_start(pdev, 0); 1653 aac->scsi_host_ptr = shost; 1654 aac->pdev = pdev; 1655 aac->name = aac_driver_template.name; 1656 aac->id = shost->unique_id; 1657 aac->cardtype = index; 1658 INIT_LIST_HEAD(&aac->entry); 1659 1660 if (aac_reset_devices || reset_devices) 1661 aac->init_reset = true; 1662 1663 aac->fibs = kcalloc(shost->can_queue + AAC_NUM_MGT_FIB, 1664 sizeof(struct fib), 1665 GFP_KERNEL); 1666 if (!aac->fibs) { 1667 error = -ENOMEM; 1668 goto out_free_host; 1669 } 1670 1671 spin_lock_init(&aac->fib_lock); 1672 1673 mutex_init(&aac->ioctl_mutex); 1674 mutex_init(&aac->scan_mutex); 1675 1676 INIT_DELAYED_WORK(&aac->safw_rescan_work, aac_safw_rescan_worker); 1677 INIT_DELAYED_WORK(&aac->src_reinit_aif_worker, 1678 aac_src_reinit_aif_worker); 1679 /* 1680 * Map in the registers from the adapter. 1681 */ 1682 aac->base_size = AAC_MIN_FOOTPRINT_SIZE; 1683 if ((*aac_drivers[index].init)(aac)) { 1684 error = -ENODEV; 1685 goto out_unmap; 1686 } 1687 1688 if (aac->sync_mode) { 1689 if (aac_sync_mode) 1690 printk(KERN_INFO "%s%d: Sync. mode enforced " 1691 "by driver parameter. This will cause " 1692 "a significant performance decrease!\n", 1693 aac->name, 1694 aac->id); 1695 else 1696 printk(KERN_INFO "%s%d: Async. mode not supported " 1697 "by current driver, sync. mode enforced." 1698 "\nPlease update driver to get full performance.\n", 1699 aac->name, 1700 aac->id); 1701 } 1702 1703 /* 1704 * Start any kernel threads needed 1705 */ 1706 aac->thread = kthread_run(aac_command_thread, aac, AAC_DRIVERNAME); 1707 if (IS_ERR(aac->thread)) { 1708 printk(KERN_ERR "aacraid: Unable to create command thread.\n"); 1709 error = PTR_ERR(aac->thread); 1710 aac->thread = NULL; 1711 goto out_deinit; 1712 } 1713 1714 aac->maximum_num_channels = aac_drivers[index].channels; 1715 error = aac_get_adapter_info(aac); 1716 if (error < 0) 1717 goto out_deinit; 1718 1719 /* 1720 * Lets override negotiations and drop the maximum SG limit to 34 1721 */ 1722 if ((aac_drivers[index].quirks & AAC_QUIRK_34SG) && 1723 (shost->sg_tablesize > 34)) { 1724 shost->sg_tablesize = 34; 1725 shost->max_sectors = (shost->sg_tablesize * 8) + 112; 1726 } 1727 1728 if ((aac_drivers[index].quirks & AAC_QUIRK_17SG) && 1729 (shost->sg_tablesize > 17)) { 1730 shost->sg_tablesize = 17; 1731 shost->max_sectors = (shost->sg_tablesize * 8) + 112; 1732 } 1733 1734 if (aac->adapter_info.options & AAC_OPT_NEW_COMM) 1735 shost->max_segment_size = shost->max_sectors << 9; 1736 else 1737 shost->max_segment_size = 65536; 1738 1739 /* 1740 * Firmware printf works only with older firmware. 1741 */ 1742 if (aac_drivers[index].quirks & AAC_QUIRK_34SG) 1743 aac->printf_enabled = 1; 1744 else 1745 aac->printf_enabled = 0; 1746 1747 /* 1748 * max channel will be the physical channels plus 1 virtual channel 1749 * all containers are on the virtual channel 0 (CONTAINER_CHANNEL) 1750 * physical channels are address by their actual physical number+1 1751 */ 1752 if (aac->nondasd_support || expose_physicals || aac->jbod) 1753 shost->max_channel = aac->maximum_num_channels; 1754 else 1755 shost->max_channel = 0; 1756 1757 aac_get_config_status(aac, 0); 1758 aac_get_containers(aac); 1759 list_add(&aac->entry, insert); 1760 1761 shost->max_id = aac->maximum_num_containers; 1762 if (shost->max_id < aac->maximum_num_physicals) 1763 shost->max_id = aac->maximum_num_physicals; 1764 if (shost->max_id < MAXIMUM_NUM_CONTAINERS) 1765 shost->max_id = MAXIMUM_NUM_CONTAINERS; 1766 else 1767 shost->this_id = shost->max_id; 1768 1769 if (!aac->sa_firmware && aac_drivers[index].quirks & AAC_QUIRK_SRC) 1770 aac_intr_normal(aac, 0, 2, 0, NULL); 1771 1772 /* 1773 * dmb - we may need to move the setting of these parms somewhere else once 1774 * we get a fib that can report the actual numbers 1775 */ 1776 shost->max_lun = AAC_MAX_LUN; 1777 1778 pci_set_drvdata(pdev, shost); 1779 1780 error = scsi_add_host(shost, &pdev->dev); 1781 if (error) 1782 goto out_deinit; 1783 1784 aac_scan_host(aac); 1785 1786 pci_enable_pcie_error_reporting(pdev); 1787 pci_save_state(pdev); 1788 1789 return 0; 1790 1791 out_deinit: 1792 __aac_shutdown(aac); 1793 out_unmap: 1794 aac_fib_map_free(aac); 1795 if (aac->comm_addr) 1796 dma_free_coherent(&aac->pdev->dev, aac->comm_size, 1797 aac->comm_addr, aac->comm_phys); 1798 kfree(aac->queues); 1799 aac_adapter_ioremap(aac, 0); 1800 kfree(aac->fibs); 1801 kfree(aac->fsa_dev); 1802 out_free_host: 1803 scsi_host_put(shost); 1804 out_disable_pdev: 1805 pci_disable_device(pdev); 1806 out: 1807 return error; 1808 } 1809 1810 static void aac_release_resources(struct aac_dev *aac) 1811 { 1812 aac_adapter_disable_int(aac); 1813 aac_free_irq(aac); 1814 } 1815 1816 static int aac_acquire_resources(struct aac_dev *dev) 1817 { 1818 unsigned long status; 1819 /* 1820 * First clear out all interrupts. Then enable the one's that we 1821 * can handle. 1822 */ 1823 while (!((status = src_readl(dev, MUnit.OMR)) & KERNEL_UP_AND_RUNNING) 1824 || status == 0xffffffff) 1825 msleep(20); 1826 1827 aac_adapter_disable_int(dev); 1828 aac_adapter_enable_int(dev); 1829 1830 1831 if (aac_is_src(dev)) 1832 aac_define_int_mode(dev); 1833 1834 if (dev->msi_enabled) 1835 aac_src_access_devreg(dev, AAC_ENABLE_MSIX); 1836 1837 if (aac_acquire_irq(dev)) 1838 goto error_iounmap; 1839 1840 aac_adapter_enable_int(dev); 1841 1842 /*max msix may change after EEH 1843 * Re-assign vectors to fibs 1844 */ 1845 aac_fib_vector_assign(dev); 1846 1847 if (!dev->sync_mode) { 1848 /* After EEH recovery or suspend resume, max_msix count 1849 * may change, therefore updating in init as well. 1850 */ 1851 dev->init->r7.no_of_msix_vectors = cpu_to_le32(dev->max_msix); 1852 aac_adapter_start(dev); 1853 } 1854 return 0; 1855 1856 error_iounmap: 1857 return -1; 1858 1859 } 1860 1861 static int __maybe_unused aac_suspend(struct device *dev) 1862 { 1863 struct Scsi_Host *shost = dev_get_drvdata(dev); 1864 struct aac_dev *aac = (struct aac_dev *)shost->hostdata; 1865 1866 scsi_host_block(shost); 1867 aac_cancel_rescan_worker(aac); 1868 aac_send_shutdown(aac); 1869 1870 aac_release_resources(aac); 1871 1872 return 0; 1873 } 1874 1875 static int __maybe_unused aac_resume(struct device *dev) 1876 { 1877 struct Scsi_Host *shost = dev_get_drvdata(dev); 1878 struct aac_dev *aac = (struct aac_dev *)shost->hostdata; 1879 1880 if (aac_acquire_resources(aac)) 1881 goto fail_device; 1882 /* 1883 * reset this flag to unblock ioctl() as it was set at 1884 * aac_send_shutdown() to block ioctls from upperlayer 1885 */ 1886 aac->adapter_shutdown = 0; 1887 scsi_host_unblock(shost, SDEV_RUNNING); 1888 1889 return 0; 1890 1891 fail_device: 1892 printk(KERN_INFO "%s%d: resume failed.\n", aac->name, aac->id); 1893 scsi_host_put(shost); 1894 return -ENODEV; 1895 } 1896 1897 static void aac_shutdown(struct pci_dev *dev) 1898 { 1899 struct Scsi_Host *shost = pci_get_drvdata(dev); 1900 1901 scsi_host_block(shost); 1902 __aac_shutdown((struct aac_dev *)shost->hostdata); 1903 } 1904 1905 static void aac_remove_one(struct pci_dev *pdev) 1906 { 1907 struct Scsi_Host *shost = pci_get_drvdata(pdev); 1908 struct aac_dev *aac = (struct aac_dev *)shost->hostdata; 1909 1910 aac_cancel_rescan_worker(aac); 1911 scsi_remove_host(shost); 1912 1913 __aac_shutdown(aac); 1914 aac_fib_map_free(aac); 1915 dma_free_coherent(&aac->pdev->dev, aac->comm_size, aac->comm_addr, 1916 aac->comm_phys); 1917 kfree(aac->queues); 1918 1919 aac_adapter_ioremap(aac, 0); 1920 1921 kfree(aac->fibs); 1922 kfree(aac->fsa_dev); 1923 1924 list_del(&aac->entry); 1925 scsi_host_put(shost); 1926 pci_disable_device(pdev); 1927 if (list_empty(&aac_devices)) { 1928 unregister_chrdev(aac_cfg_major, "aac"); 1929 aac_cfg_major = AAC_CHARDEV_NEEDS_REINIT; 1930 } 1931 } 1932 1933 static pci_ers_result_t aac_pci_error_detected(struct pci_dev *pdev, 1934 pci_channel_state_t error) 1935 { 1936 struct Scsi_Host *shost = pci_get_drvdata(pdev); 1937 struct aac_dev *aac = shost_priv(shost); 1938 1939 dev_err(&pdev->dev, "aacraid: PCI error detected %x\n", error); 1940 1941 switch (error) { 1942 case pci_channel_io_normal: 1943 return PCI_ERS_RESULT_CAN_RECOVER; 1944 case pci_channel_io_frozen: 1945 aac->handle_pci_error = 1; 1946 1947 scsi_host_block(shost); 1948 aac_cancel_rescan_worker(aac); 1949 scsi_host_complete_all_commands(shost, DID_NO_CONNECT); 1950 aac_release_resources(aac); 1951 1952 pci_disable_pcie_error_reporting(pdev); 1953 aac_adapter_ioremap(aac, 0); 1954 1955 return PCI_ERS_RESULT_NEED_RESET; 1956 case pci_channel_io_perm_failure: 1957 aac->handle_pci_error = 1; 1958 1959 scsi_host_complete_all_commands(shost, DID_NO_CONNECT); 1960 return PCI_ERS_RESULT_DISCONNECT; 1961 } 1962 1963 return PCI_ERS_RESULT_NEED_RESET; 1964 } 1965 1966 static pci_ers_result_t aac_pci_mmio_enabled(struct pci_dev *pdev) 1967 { 1968 dev_err(&pdev->dev, "aacraid: PCI error - mmio enabled\n"); 1969 return PCI_ERS_RESULT_NEED_RESET; 1970 } 1971 1972 static pci_ers_result_t aac_pci_slot_reset(struct pci_dev *pdev) 1973 { 1974 dev_err(&pdev->dev, "aacraid: PCI error - slot reset\n"); 1975 pci_restore_state(pdev); 1976 if (pci_enable_device(pdev)) { 1977 dev_warn(&pdev->dev, 1978 "aacraid: failed to enable slave\n"); 1979 goto fail_device; 1980 } 1981 1982 pci_set_master(pdev); 1983 1984 if (pci_enable_device_mem(pdev)) { 1985 dev_err(&pdev->dev, "pci_enable_device_mem failed\n"); 1986 goto fail_device; 1987 } 1988 1989 return PCI_ERS_RESULT_RECOVERED; 1990 1991 fail_device: 1992 dev_err(&pdev->dev, "aacraid: PCI error - slot reset failed\n"); 1993 return PCI_ERS_RESULT_DISCONNECT; 1994 } 1995 1996 1997 static void aac_pci_resume(struct pci_dev *pdev) 1998 { 1999 struct Scsi_Host *shost = pci_get_drvdata(pdev); 2000 struct aac_dev *aac = (struct aac_dev *)shost_priv(shost); 2001 2002 if (aac_adapter_ioremap(aac, aac->base_size)) { 2003 2004 dev_err(&pdev->dev, "aacraid: ioremap failed\n"); 2005 /* remap failed, go back ... */ 2006 aac->comm_interface = AAC_COMM_PRODUCER; 2007 if (aac_adapter_ioremap(aac, AAC_MIN_FOOTPRINT_SIZE)) { 2008 dev_warn(&pdev->dev, 2009 "aacraid: unable to map adapter.\n"); 2010 2011 return; 2012 } 2013 } 2014 2015 msleep(10000); 2016 2017 aac_acquire_resources(aac); 2018 2019 /* 2020 * reset this flag to unblock ioctl() as it was set 2021 * at aac_send_shutdown() to block ioctls from upperlayer 2022 */ 2023 aac->adapter_shutdown = 0; 2024 aac->handle_pci_error = 0; 2025 2026 scsi_host_unblock(shost, SDEV_RUNNING); 2027 aac_scan_host(aac); 2028 pci_save_state(pdev); 2029 2030 dev_err(&pdev->dev, "aacraid: PCI error - resume\n"); 2031 } 2032 2033 static struct pci_error_handlers aac_pci_err_handler = { 2034 .error_detected = aac_pci_error_detected, 2035 .mmio_enabled = aac_pci_mmio_enabled, 2036 .slot_reset = aac_pci_slot_reset, 2037 .resume = aac_pci_resume, 2038 }; 2039 2040 static SIMPLE_DEV_PM_OPS(aac_pm_ops, aac_suspend, aac_resume); 2041 2042 static struct pci_driver aac_pci_driver = { 2043 .name = AAC_DRIVERNAME, 2044 .id_table = aac_pci_tbl, 2045 .probe = aac_probe_one, 2046 .remove = aac_remove_one, 2047 .driver.pm = &aac_pm_ops, 2048 .shutdown = aac_shutdown, 2049 .err_handler = &aac_pci_err_handler, 2050 }; 2051 2052 static int __init aac_init(void) 2053 { 2054 int error; 2055 2056 printk(KERN_INFO "Adaptec %s driver %s\n", 2057 AAC_DRIVERNAME, aac_driver_version); 2058 2059 error = pci_register_driver(&aac_pci_driver); 2060 if (error < 0) 2061 return error; 2062 2063 aac_init_char(); 2064 2065 2066 return 0; 2067 } 2068 2069 static void __exit aac_exit(void) 2070 { 2071 if (aac_cfg_major > -1) 2072 unregister_chrdev(aac_cfg_major, "aac"); 2073 pci_unregister_driver(&aac_pci_driver); 2074 } 2075 2076 module_init(aac_init); 2077 module_exit(aac_exit); 2078