1 /* -*- mode: c; c-basic-offset: 8 -*- */ 2 3 /* NCR (or Symbios) 53c700 and 53c700-66 Driver 4 * 5 * Copyright (C) 2001 by James.Bottomley@HansenPartnership.com 6 **----------------------------------------------------------------------------- 7 ** 8 ** This program is free software; you can redistribute it and/or modify 9 ** it under the terms of the GNU General Public License as published by 10 ** the Free Software Foundation; either version 2 of the License, or 11 ** (at your option) any later version. 12 ** 13 ** This program is distributed in the hope that it will be useful, 14 ** but WITHOUT ANY WARRANTY; without even the implied warranty of 15 ** MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 16 ** GNU General Public License for more details. 17 ** 18 ** You should have received a copy of the GNU General Public License 19 ** along with this program; if not, write to the Free Software 20 ** Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 21 ** 22 **----------------------------------------------------------------------------- 23 */ 24 25 /* Notes: 26 * 27 * This driver is designed exclusively for these chips (virtually the 28 * earliest of the scripts engine chips). They need their own drivers 29 * because they are missing so many of the scripts and snazzy register 30 * features of their elder brothers (the 710, 720 and 770). 31 * 32 * The 700 is the lowliest of the line, it can only do async SCSI. 33 * The 700-66 can at least do synchronous SCSI up to 10MHz. 34 * 35 * The 700 chip has no host bus interface logic of its own. However, 36 * it is usually mapped to a location with well defined register 37 * offsets. Therefore, if you can determine the base address and the 38 * irq your board incorporating this chip uses, you can probably use 39 * this driver to run it (although you'll probably have to write a 40 * minimal wrapper for the purpose---see the NCR_D700 driver for 41 * details about how to do this). 42 * 43 * 44 * TODO List: 45 * 46 * 1. Better statistics in the proc fs 47 * 48 * 2. Implement message queue (queues SCSI messages like commands) and make 49 * the abort and device reset functions use them. 50 * */ 51 52 /* CHANGELOG 53 * 54 * Version 2.8 55 * 56 * Fixed bad bug affecting tag starvation processing (previously the 57 * driver would hang the system if too many tags starved. Also fixed 58 * bad bug having to do with 10 byte command processing and REQUEST 59 * SENSE (the command would loop forever getting a transfer length 60 * mismatch in the CMD phase). 61 * 62 * Version 2.7 63 * 64 * Fixed scripts problem which caused certain devices (notably CDRWs) 65 * to hang on initial INQUIRY. Updated NCR_700_readl/writel to use 66 * __raw_readl/writel for parisc compatibility (Thomas 67 * Bogendoerfer). Added missing SCp->request_bufflen initialisation 68 * for sense requests (Ryan Bradetich). 69 * 70 * Version 2.6 71 * 72 * Following test of the 64 bit parisc kernel by Richard Hirst, 73 * several problems have now been corrected. Also adds support for 74 * consistent memory allocation. 75 * 76 * Version 2.5 77 * 78 * More Compatibility changes for 710 (now actually works). Enhanced 79 * support for odd clock speeds which constrain SDTR negotiations. 80 * correct cacheline separation for scsi messages and status for 81 * incoherent architectures. Use of the pci mapping functions on 82 * buffers to begin support for 64 bit drivers. 83 * 84 * Version 2.4 85 * 86 * Added support for the 53c710 chip (in 53c700 emulation mode only---no 87 * special 53c710 instructions or registers are used). 88 * 89 * Version 2.3 90 * 91 * More endianness/cache coherency changes. 92 * 93 * Better bad device handling (handles devices lying about tag 94 * queueing support and devices which fail to provide sense data on 95 * contingent allegiance conditions) 96 * 97 * Many thanks to Richard Hirst <rhirst@linuxcare.com> for patiently 98 * debugging this driver on the parisc architecture and suggesting 99 * many improvements and bug fixes. 100 * 101 * Thanks also go to Linuxcare Inc. for providing several PARISC 102 * machines for me to debug the driver on. 103 * 104 * Version 2.2 105 * 106 * Made the driver mem or io mapped; added endian invariance; added 107 * dma cache flushing operations for architectures which need it; 108 * added support for more varied clocking speeds. 109 * 110 * Version 2.1 111 * 112 * Initial modularisation from the D700. See NCR_D700.c for the rest of 113 * the changelog. 114 * */ 115 #define NCR_700_VERSION "2.8" 116 117 #include <linux/kernel.h> 118 #include <linux/types.h> 119 #include <linux/string.h> 120 #include <linux/slab.h> 121 #include <linux/ioport.h> 122 #include <linux/delay.h> 123 #include <linux/spinlock.h> 124 #include <linux/completion.h> 125 #include <linux/init.h> 126 #include <linux/proc_fs.h> 127 #include <linux/blkdev.h> 128 #include <linux/module.h> 129 #include <linux/interrupt.h> 130 #include <linux/device.h> 131 #include <asm/dma.h> 132 #include <asm/io.h> 133 #include <asm/pgtable.h> 134 #include <asm/byteorder.h> 135 136 #include <scsi/scsi.h> 137 #include <scsi/scsi_cmnd.h> 138 #include <scsi/scsi_dbg.h> 139 #include <scsi/scsi_eh.h> 140 #include <scsi/scsi_host.h> 141 #include <scsi/scsi_tcq.h> 142 #include <scsi/scsi_transport.h> 143 #include <scsi/scsi_transport_spi.h> 144 145 #include "53c700.h" 146 147 /* NOTE: For 64 bit drivers there are points in the code where we use 148 * a non dereferenceable pointer to point to a structure in dma-able 149 * memory (which is 32 bits) so that we can use all of the structure 150 * operations but take the address at the end. This macro allows us 151 * to truncate the 64 bit pointer down to 32 bits without the compiler 152 * complaining */ 153 #define to32bit(x) ((__u32)((unsigned long)(x))) 154 155 #ifdef NCR_700_DEBUG 156 #define STATIC 157 #else 158 #define STATIC static 159 #endif 160 161 MODULE_AUTHOR("James Bottomley"); 162 MODULE_DESCRIPTION("53c700 and 53c700-66 Driver"); 163 MODULE_LICENSE("GPL"); 164 165 /* This is the script */ 166 #include "53c700_d.h" 167 168 169 STATIC int NCR_700_queuecommand(struct Scsi_Host *h, struct scsi_cmnd *); 170 STATIC int NCR_700_abort(struct scsi_cmnd * SCpnt); 171 STATIC int NCR_700_bus_reset(struct scsi_cmnd * SCpnt); 172 STATIC int NCR_700_host_reset(struct scsi_cmnd * SCpnt); 173 STATIC void NCR_700_chip_setup(struct Scsi_Host *host); 174 STATIC void NCR_700_chip_reset(struct Scsi_Host *host); 175 STATIC int NCR_700_slave_alloc(struct scsi_device *SDpnt); 176 STATIC int NCR_700_slave_configure(struct scsi_device *SDpnt); 177 STATIC void NCR_700_slave_destroy(struct scsi_device *SDpnt); 178 static int NCR_700_change_queue_depth(struct scsi_device *SDpnt, int depth); 179 180 STATIC struct device_attribute *NCR_700_dev_attrs[]; 181 182 STATIC struct scsi_transport_template *NCR_700_transport_template = NULL; 183 184 static char *NCR_700_phase[] = { 185 "", 186 "after selection", 187 "before command phase", 188 "after command phase", 189 "after status phase", 190 "after data in phase", 191 "after data out phase", 192 "during data phase", 193 }; 194 195 static char *NCR_700_condition[] = { 196 "", 197 "NOT MSG_OUT", 198 "UNEXPECTED PHASE", 199 "NOT MSG_IN", 200 "UNEXPECTED MSG", 201 "MSG_IN", 202 "SDTR_MSG RECEIVED", 203 "REJECT_MSG RECEIVED", 204 "DISCONNECT_MSG RECEIVED", 205 "MSG_OUT", 206 "DATA_IN", 207 208 }; 209 210 static char *NCR_700_fatal_messages[] = { 211 "unexpected message after reselection", 212 "still MSG_OUT after message injection", 213 "not MSG_IN after selection", 214 "Illegal message length received", 215 }; 216 217 static char *NCR_700_SBCL_bits[] = { 218 "IO ", 219 "CD ", 220 "MSG ", 221 "ATN ", 222 "SEL ", 223 "BSY ", 224 "ACK ", 225 "REQ ", 226 }; 227 228 static char *NCR_700_SBCL_to_phase[] = { 229 "DATA_OUT", 230 "DATA_IN", 231 "CMD_OUT", 232 "STATE", 233 "ILLEGAL PHASE", 234 "ILLEGAL PHASE", 235 "MSG OUT", 236 "MSG IN", 237 }; 238 239 /* This translates the SDTR message offset and period to a value 240 * which can be loaded into the SXFER_REG. 241 * 242 * NOTE: According to SCSI-2, the true transfer period (in ns) is 243 * actually four times this period value */ 244 static inline __u8 245 NCR_700_offset_period_to_sxfer(struct NCR_700_Host_Parameters *hostdata, 246 __u8 offset, __u8 period) 247 { 248 int XFERP; 249 250 __u8 min_xferp = (hostdata->chip710 251 ? NCR_710_MIN_XFERP : NCR_700_MIN_XFERP); 252 __u8 max_offset = (hostdata->chip710 253 ? NCR_710_MAX_OFFSET : NCR_700_MAX_OFFSET); 254 255 if(offset == 0) 256 return 0; 257 258 if(period < hostdata->min_period) { 259 printk(KERN_WARNING "53c700: Period %dns is less than this chip's minimum, setting to %d\n", period*4, NCR_700_MIN_PERIOD*4); 260 period = hostdata->min_period; 261 } 262 XFERP = (period*4 * hostdata->sync_clock)/1000 - 4; 263 if(offset > max_offset) { 264 printk(KERN_WARNING "53c700: Offset %d exceeds chip maximum, setting to %d\n", 265 offset, max_offset); 266 offset = max_offset; 267 } 268 if(XFERP < min_xferp) { 269 XFERP = min_xferp; 270 } 271 return (offset & 0x0f) | (XFERP & 0x07)<<4; 272 } 273 274 static inline __u8 275 NCR_700_get_SXFER(struct scsi_device *SDp) 276 { 277 struct NCR_700_Host_Parameters *hostdata = 278 (struct NCR_700_Host_Parameters *)SDp->host->hostdata[0]; 279 280 return NCR_700_offset_period_to_sxfer(hostdata, 281 spi_offset(SDp->sdev_target), 282 spi_period(SDp->sdev_target)); 283 } 284 285 struct Scsi_Host * 286 NCR_700_detect(struct scsi_host_template *tpnt, 287 struct NCR_700_Host_Parameters *hostdata, struct device *dev) 288 { 289 dma_addr_t pScript, pSlots; 290 __u8 *memory; 291 __u32 *script; 292 struct Scsi_Host *host; 293 static int banner = 0; 294 int j; 295 296 if(tpnt->sdev_attrs == NULL) 297 tpnt->sdev_attrs = NCR_700_dev_attrs; 298 299 memory = dma_alloc_noncoherent(hostdata->dev, TOTAL_MEM_SIZE, 300 &pScript, GFP_KERNEL); 301 if(memory == NULL) { 302 printk(KERN_ERR "53c700: Failed to allocate memory for driver, detaching\n"); 303 return NULL; 304 } 305 306 script = (__u32 *)memory; 307 hostdata->msgin = memory + MSGIN_OFFSET; 308 hostdata->msgout = memory + MSGOUT_OFFSET; 309 hostdata->status = memory + STATUS_OFFSET; 310 hostdata->slots = (struct NCR_700_command_slot *)(memory + SLOTS_OFFSET); 311 hostdata->dev = dev; 312 313 pSlots = pScript + SLOTS_OFFSET; 314 315 /* Fill in the missing routines from the host template */ 316 tpnt->queuecommand = NCR_700_queuecommand; 317 tpnt->eh_abort_handler = NCR_700_abort; 318 tpnt->eh_bus_reset_handler = NCR_700_bus_reset; 319 tpnt->eh_host_reset_handler = NCR_700_host_reset; 320 tpnt->can_queue = NCR_700_COMMAND_SLOTS_PER_HOST; 321 tpnt->sg_tablesize = NCR_700_SG_SEGMENTS; 322 tpnt->cmd_per_lun = NCR_700_CMD_PER_LUN; 323 tpnt->use_clustering = ENABLE_CLUSTERING; 324 tpnt->slave_configure = NCR_700_slave_configure; 325 tpnt->slave_destroy = NCR_700_slave_destroy; 326 tpnt->slave_alloc = NCR_700_slave_alloc; 327 tpnt->change_queue_depth = NCR_700_change_queue_depth; 328 329 if(tpnt->name == NULL) 330 tpnt->name = "53c700"; 331 if(tpnt->proc_name == NULL) 332 tpnt->proc_name = "53c700"; 333 334 host = scsi_host_alloc(tpnt, 4); 335 if (!host) 336 return NULL; 337 memset(hostdata->slots, 0, sizeof(struct NCR_700_command_slot) 338 * NCR_700_COMMAND_SLOTS_PER_HOST); 339 for (j = 0; j < NCR_700_COMMAND_SLOTS_PER_HOST; j++) { 340 dma_addr_t offset = (dma_addr_t)((unsigned long)&hostdata->slots[j].SG[0] 341 - (unsigned long)&hostdata->slots[0].SG[0]); 342 hostdata->slots[j].pSG = (struct NCR_700_SG_List *)((unsigned long)(pSlots + offset)); 343 if(j == 0) 344 hostdata->free_list = &hostdata->slots[j]; 345 else 346 hostdata->slots[j-1].ITL_forw = &hostdata->slots[j]; 347 hostdata->slots[j].state = NCR_700_SLOT_FREE; 348 } 349 350 for (j = 0; j < ARRAY_SIZE(SCRIPT); j++) 351 script[j] = bS_to_host(SCRIPT[j]); 352 353 /* adjust all labels to be bus physical */ 354 for (j = 0; j < PATCHES; j++) 355 script[LABELPATCHES[j]] = bS_to_host(pScript + SCRIPT[LABELPATCHES[j]]); 356 /* now patch up fixed addresses. */ 357 script_patch_32(hostdata->dev, script, MessageLocation, 358 pScript + MSGOUT_OFFSET); 359 script_patch_32(hostdata->dev, script, StatusAddress, 360 pScript + STATUS_OFFSET); 361 script_patch_32(hostdata->dev, script, ReceiveMsgAddress, 362 pScript + MSGIN_OFFSET); 363 364 hostdata->script = script; 365 hostdata->pScript = pScript; 366 dma_sync_single_for_device(hostdata->dev, pScript, sizeof(SCRIPT), DMA_TO_DEVICE); 367 hostdata->state = NCR_700_HOST_FREE; 368 hostdata->cmd = NULL; 369 host->max_id = 8; 370 host->max_lun = NCR_700_MAX_LUNS; 371 BUG_ON(NCR_700_transport_template == NULL); 372 host->transportt = NCR_700_transport_template; 373 host->unique_id = (unsigned long)hostdata->base; 374 hostdata->eh_complete = NULL; 375 host->hostdata[0] = (unsigned long)hostdata; 376 /* kick the chip */ 377 NCR_700_writeb(0xff, host, CTEST9_REG); 378 if (hostdata->chip710) 379 hostdata->rev = (NCR_700_readb(host, CTEST8_REG)>>4) & 0x0f; 380 else 381 hostdata->rev = (NCR_700_readb(host, CTEST7_REG)>>4) & 0x0f; 382 hostdata->fast = (NCR_700_readb(host, CTEST9_REG) == 0); 383 if (banner == 0) { 384 printk(KERN_NOTICE "53c700: Version " NCR_700_VERSION " By James.Bottomley@HansenPartnership.com\n"); 385 banner = 1; 386 } 387 printk(KERN_NOTICE "scsi%d: %s rev %d %s\n", host->host_no, 388 hostdata->chip710 ? "53c710" : 389 (hostdata->fast ? "53c700-66" : "53c700"), 390 hostdata->rev, hostdata->differential ? 391 "(Differential)" : ""); 392 /* reset the chip */ 393 NCR_700_chip_reset(host); 394 395 if (scsi_add_host(host, dev)) { 396 dev_printk(KERN_ERR, dev, "53c700: scsi_add_host failed\n"); 397 scsi_host_put(host); 398 return NULL; 399 } 400 401 spi_signalling(host) = hostdata->differential ? SPI_SIGNAL_HVD : 402 SPI_SIGNAL_SE; 403 404 return host; 405 } 406 407 int 408 NCR_700_release(struct Scsi_Host *host) 409 { 410 struct NCR_700_Host_Parameters *hostdata = 411 (struct NCR_700_Host_Parameters *)host->hostdata[0]; 412 413 dma_free_noncoherent(hostdata->dev, TOTAL_MEM_SIZE, 414 hostdata->script, hostdata->pScript); 415 return 1; 416 } 417 418 static inline __u8 419 NCR_700_identify(int can_disconnect, __u8 lun) 420 { 421 return IDENTIFY_BASE | 422 ((can_disconnect) ? 0x40 : 0) | 423 (lun & NCR_700_LUN_MASK); 424 } 425 426 /* 427 * Function : static int data_residual (Scsi_Host *host) 428 * 429 * Purpose : return residual data count of what's in the chip. If you 430 * really want to know what this function is doing, it's almost a 431 * direct transcription of the algorithm described in the 53c710 432 * guide, except that the DBC and DFIFO registers are only 6 bits 433 * wide on a 53c700. 434 * 435 * Inputs : host - SCSI host */ 436 static inline int 437 NCR_700_data_residual (struct Scsi_Host *host) { 438 struct NCR_700_Host_Parameters *hostdata = 439 (struct NCR_700_Host_Parameters *)host->hostdata[0]; 440 int count, synchronous = 0; 441 unsigned int ddir; 442 443 if(hostdata->chip710) { 444 count = ((NCR_700_readb(host, DFIFO_REG) & 0x7f) - 445 (NCR_700_readl(host, DBC_REG) & 0x7f)) & 0x7f; 446 } else { 447 count = ((NCR_700_readb(host, DFIFO_REG) & 0x3f) - 448 (NCR_700_readl(host, DBC_REG) & 0x3f)) & 0x3f; 449 } 450 451 if(hostdata->fast) 452 synchronous = NCR_700_readb(host, SXFER_REG) & 0x0f; 453 454 /* get the data direction */ 455 ddir = NCR_700_readb(host, CTEST0_REG) & 0x01; 456 457 if (ddir) { 458 /* Receive */ 459 if (synchronous) 460 count += (NCR_700_readb(host, SSTAT2_REG) & 0xf0) >> 4; 461 else 462 if (NCR_700_readb(host, SSTAT1_REG) & SIDL_REG_FULL) 463 ++count; 464 } else { 465 /* Send */ 466 __u8 sstat = NCR_700_readb(host, SSTAT1_REG); 467 if (sstat & SODL_REG_FULL) 468 ++count; 469 if (synchronous && (sstat & SODR_REG_FULL)) 470 ++count; 471 } 472 #ifdef NCR_700_DEBUG 473 if(count) 474 printk("RESIDUAL IS %d (ddir %d)\n", count, ddir); 475 #endif 476 return count; 477 } 478 479 /* print out the SCSI wires and corresponding phase from the SBCL register 480 * in the chip */ 481 static inline char * 482 sbcl_to_string(__u8 sbcl) 483 { 484 int i; 485 static char ret[256]; 486 487 ret[0]='\0'; 488 for(i=0; i<8; i++) { 489 if((1<<i) & sbcl) 490 strcat(ret, NCR_700_SBCL_bits[i]); 491 } 492 strcat(ret, NCR_700_SBCL_to_phase[sbcl & 0x07]); 493 return ret; 494 } 495 496 static inline __u8 497 bitmap_to_number(__u8 bitmap) 498 { 499 __u8 i; 500 501 for(i=0; i<8 && !(bitmap &(1<<i)); i++) 502 ; 503 return i; 504 } 505 506 /* Pull a slot off the free list */ 507 STATIC struct NCR_700_command_slot * 508 find_empty_slot(struct NCR_700_Host_Parameters *hostdata) 509 { 510 struct NCR_700_command_slot *slot = hostdata->free_list; 511 512 if(slot == NULL) { 513 /* sanity check */ 514 if(hostdata->command_slot_count != NCR_700_COMMAND_SLOTS_PER_HOST) 515 printk(KERN_ERR "SLOTS FULL, but count is %d, should be %d\n", hostdata->command_slot_count, NCR_700_COMMAND_SLOTS_PER_HOST); 516 return NULL; 517 } 518 519 if(slot->state != NCR_700_SLOT_FREE) 520 /* should panic! */ 521 printk(KERN_ERR "BUSY SLOT ON FREE LIST!!!\n"); 522 523 524 hostdata->free_list = slot->ITL_forw; 525 slot->ITL_forw = NULL; 526 527 528 /* NOTE: set the state to busy here, not queued, since this 529 * indicates the slot is in use and cannot be run by the IRQ 530 * finish routine. If we cannot queue the command when it 531 * is properly build, we then change to NCR_700_SLOT_QUEUED */ 532 slot->state = NCR_700_SLOT_BUSY; 533 slot->flags = 0; 534 hostdata->command_slot_count++; 535 536 return slot; 537 } 538 539 STATIC void 540 free_slot(struct NCR_700_command_slot *slot, 541 struct NCR_700_Host_Parameters *hostdata) 542 { 543 if((slot->state & NCR_700_SLOT_MASK) != NCR_700_SLOT_MAGIC) { 544 printk(KERN_ERR "53c700: SLOT %p is not MAGIC!!!\n", slot); 545 } 546 if(slot->state == NCR_700_SLOT_FREE) { 547 printk(KERN_ERR "53c700: SLOT %p is FREE!!!\n", slot); 548 } 549 550 slot->resume_offset = 0; 551 slot->cmnd = NULL; 552 slot->state = NCR_700_SLOT_FREE; 553 slot->ITL_forw = hostdata->free_list; 554 hostdata->free_list = slot; 555 hostdata->command_slot_count--; 556 } 557 558 559 /* This routine really does very little. The command is indexed on 560 the ITL and (if tagged) the ITLQ lists in _queuecommand */ 561 STATIC void 562 save_for_reselection(struct NCR_700_Host_Parameters *hostdata, 563 struct scsi_cmnd *SCp, __u32 dsp) 564 { 565 /* Its just possible that this gets executed twice */ 566 if(SCp != NULL) { 567 struct NCR_700_command_slot *slot = 568 (struct NCR_700_command_slot *)SCp->host_scribble; 569 570 slot->resume_offset = dsp; 571 } 572 hostdata->state = NCR_700_HOST_FREE; 573 hostdata->cmd = NULL; 574 } 575 576 STATIC inline void 577 NCR_700_unmap(struct NCR_700_Host_Parameters *hostdata, struct scsi_cmnd *SCp, 578 struct NCR_700_command_slot *slot) 579 { 580 if(SCp->sc_data_direction != DMA_NONE && 581 SCp->sc_data_direction != DMA_BIDIRECTIONAL) 582 scsi_dma_unmap(SCp); 583 } 584 585 STATIC inline void 586 NCR_700_scsi_done(struct NCR_700_Host_Parameters *hostdata, 587 struct scsi_cmnd *SCp, int result) 588 { 589 hostdata->state = NCR_700_HOST_FREE; 590 hostdata->cmd = NULL; 591 592 if(SCp != NULL) { 593 struct NCR_700_command_slot *slot = 594 (struct NCR_700_command_slot *)SCp->host_scribble; 595 596 dma_unmap_single(hostdata->dev, slot->pCmd, 597 MAX_COMMAND_SIZE, DMA_TO_DEVICE); 598 if (slot->flags == NCR_700_FLAG_AUTOSENSE) { 599 char *cmnd = NCR_700_get_sense_cmnd(SCp->device); 600 601 dma_unmap_single(hostdata->dev, slot->dma_handle, 602 SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE); 603 /* restore the old result if the request sense was 604 * successful */ 605 if (result == 0) 606 result = cmnd[7]; 607 /* restore the original length */ 608 SCp->cmd_len = cmnd[8]; 609 } else 610 NCR_700_unmap(hostdata, SCp, slot); 611 612 free_slot(slot, hostdata); 613 #ifdef NCR_700_DEBUG 614 if(NCR_700_get_depth(SCp->device) == 0 || 615 NCR_700_get_depth(SCp->device) > SCp->device->queue_depth) 616 printk(KERN_ERR "Invalid depth in NCR_700_scsi_done(): %d\n", 617 NCR_700_get_depth(SCp->device)); 618 #endif /* NCR_700_DEBUG */ 619 NCR_700_set_depth(SCp->device, NCR_700_get_depth(SCp->device) - 1); 620 621 SCp->host_scribble = NULL; 622 SCp->result = result; 623 SCp->scsi_done(SCp); 624 } else { 625 printk(KERN_ERR "53c700: SCSI DONE HAS NULL SCp\n"); 626 } 627 } 628 629 630 STATIC void 631 NCR_700_internal_bus_reset(struct Scsi_Host *host) 632 { 633 /* Bus reset */ 634 NCR_700_writeb(ASSERT_RST, host, SCNTL1_REG); 635 udelay(50); 636 NCR_700_writeb(0, host, SCNTL1_REG); 637 638 } 639 640 STATIC void 641 NCR_700_chip_setup(struct Scsi_Host *host) 642 { 643 struct NCR_700_Host_Parameters *hostdata = 644 (struct NCR_700_Host_Parameters *)host->hostdata[0]; 645 __u8 min_period; 646 __u8 min_xferp = (hostdata->chip710 ? NCR_710_MIN_XFERP : NCR_700_MIN_XFERP); 647 648 if(hostdata->chip710) { 649 __u8 burst_disable = 0; 650 __u8 burst_length = 0; 651 652 switch (hostdata->burst_length) { 653 case 1: 654 burst_length = BURST_LENGTH_1; 655 break; 656 case 2: 657 burst_length = BURST_LENGTH_2; 658 break; 659 case 4: 660 burst_length = BURST_LENGTH_4; 661 break; 662 case 8: 663 burst_length = BURST_LENGTH_8; 664 break; 665 default: 666 burst_disable = BURST_DISABLE; 667 break; 668 } 669 hostdata->dcntl_extra |= COMPAT_700_MODE; 670 671 NCR_700_writeb(hostdata->dcntl_extra, host, DCNTL_REG); 672 NCR_700_writeb(burst_length | hostdata->dmode_extra, 673 host, DMODE_710_REG); 674 NCR_700_writeb(burst_disable | hostdata->ctest7_extra | 675 (hostdata->differential ? DIFF : 0), 676 host, CTEST7_REG); 677 NCR_700_writeb(BTB_TIMER_DISABLE, host, CTEST0_REG); 678 NCR_700_writeb(FULL_ARBITRATION | ENABLE_PARITY | PARITY 679 | AUTO_ATN, host, SCNTL0_REG); 680 } else { 681 NCR_700_writeb(BURST_LENGTH_8 | hostdata->dmode_extra, 682 host, DMODE_700_REG); 683 NCR_700_writeb(hostdata->differential ? 684 DIFF : 0, host, CTEST7_REG); 685 if(hostdata->fast) { 686 /* this is for 700-66, does nothing on 700 */ 687 NCR_700_writeb(LAST_DIS_ENBL | ENABLE_ACTIVE_NEGATION 688 | GENERATE_RECEIVE_PARITY, host, 689 CTEST8_REG); 690 } else { 691 NCR_700_writeb(FULL_ARBITRATION | ENABLE_PARITY 692 | PARITY | AUTO_ATN, host, SCNTL0_REG); 693 } 694 } 695 696 NCR_700_writeb(1 << host->this_id, host, SCID_REG); 697 NCR_700_writeb(0, host, SBCL_REG); 698 NCR_700_writeb(ASYNC_OPERATION, host, SXFER_REG); 699 700 NCR_700_writeb(PHASE_MM_INT | SEL_TIMEOUT_INT | GROSS_ERR_INT | UX_DISC_INT 701 | RST_INT | PAR_ERR_INT | SELECT_INT, host, SIEN_REG); 702 703 NCR_700_writeb(ABORT_INT | INT_INST_INT | ILGL_INST_INT, host, DIEN_REG); 704 NCR_700_writeb(ENABLE_SELECT, host, SCNTL1_REG); 705 if(hostdata->clock > 75) { 706 printk(KERN_ERR "53c700: Clock speed %dMHz is too high: 75Mhz is the maximum this chip can be driven at\n", hostdata->clock); 707 /* do the best we can, but the async clock will be out 708 * of spec: sync divider 2, async divider 3 */ 709 DEBUG(("53c700: sync 2 async 3\n")); 710 NCR_700_writeb(SYNC_DIV_2_0, host, SBCL_REG); 711 NCR_700_writeb(ASYNC_DIV_3_0 | hostdata->dcntl_extra, host, DCNTL_REG); 712 hostdata->sync_clock = hostdata->clock/2; 713 } else if(hostdata->clock > 50 && hostdata->clock <= 75) { 714 /* sync divider 1.5, async divider 3 */ 715 DEBUG(("53c700: sync 1.5 async 3\n")); 716 NCR_700_writeb(SYNC_DIV_1_5, host, SBCL_REG); 717 NCR_700_writeb(ASYNC_DIV_3_0 | hostdata->dcntl_extra, host, DCNTL_REG); 718 hostdata->sync_clock = hostdata->clock*2; 719 hostdata->sync_clock /= 3; 720 721 } else if(hostdata->clock > 37 && hostdata->clock <= 50) { 722 /* sync divider 1, async divider 2 */ 723 DEBUG(("53c700: sync 1 async 2\n")); 724 NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG); 725 NCR_700_writeb(ASYNC_DIV_2_0 | hostdata->dcntl_extra, host, DCNTL_REG); 726 hostdata->sync_clock = hostdata->clock; 727 } else if(hostdata->clock > 25 && hostdata->clock <=37) { 728 /* sync divider 1, async divider 1.5 */ 729 DEBUG(("53c700: sync 1 async 1.5\n")); 730 NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG); 731 NCR_700_writeb(ASYNC_DIV_1_5 | hostdata->dcntl_extra, host, DCNTL_REG); 732 hostdata->sync_clock = hostdata->clock; 733 } else { 734 DEBUG(("53c700: sync 1 async 1\n")); 735 NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG); 736 NCR_700_writeb(ASYNC_DIV_1_0 | hostdata->dcntl_extra, host, DCNTL_REG); 737 /* sync divider 1, async divider 1 */ 738 hostdata->sync_clock = hostdata->clock; 739 } 740 /* Calculate the actual minimum period that can be supported 741 * by our synchronous clock speed. See the 710 manual for 742 * exact details of this calculation which is based on a 743 * setting of the SXFER register */ 744 min_period = 1000*(4+min_xferp)/(4*hostdata->sync_clock); 745 hostdata->min_period = NCR_700_MIN_PERIOD; 746 if(min_period > NCR_700_MIN_PERIOD) 747 hostdata->min_period = min_period; 748 } 749 750 STATIC void 751 NCR_700_chip_reset(struct Scsi_Host *host) 752 { 753 struct NCR_700_Host_Parameters *hostdata = 754 (struct NCR_700_Host_Parameters *)host->hostdata[0]; 755 if(hostdata->chip710) { 756 NCR_700_writeb(SOFTWARE_RESET_710, host, ISTAT_REG); 757 udelay(100); 758 759 NCR_700_writeb(0, host, ISTAT_REG); 760 } else { 761 NCR_700_writeb(SOFTWARE_RESET, host, DCNTL_REG); 762 udelay(100); 763 764 NCR_700_writeb(0, host, DCNTL_REG); 765 } 766 767 mdelay(1000); 768 769 NCR_700_chip_setup(host); 770 } 771 772 /* The heart of the message processing engine is that the instruction 773 * immediately after the INT is the normal case (and so must be CLEAR 774 * ACK). If we want to do something else, we call that routine in 775 * scripts and set temp to be the normal case + 8 (skipping the CLEAR 776 * ACK) so that the routine returns correctly to resume its activity 777 * */ 778 STATIC __u32 779 process_extended_message(struct Scsi_Host *host, 780 struct NCR_700_Host_Parameters *hostdata, 781 struct scsi_cmnd *SCp, __u32 dsp, __u32 dsps) 782 { 783 __u32 resume_offset = dsp, temp = dsp + 8; 784 __u8 pun = 0xff, lun = 0xff; 785 786 if(SCp != NULL) { 787 pun = SCp->device->id; 788 lun = SCp->device->lun; 789 } 790 791 switch(hostdata->msgin[2]) { 792 case A_SDTR_MSG: 793 if(SCp != NULL && NCR_700_is_flag_set(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION)) { 794 struct scsi_target *starget = SCp->device->sdev_target; 795 __u8 period = hostdata->msgin[3]; 796 __u8 offset = hostdata->msgin[4]; 797 798 if(offset == 0 || period == 0) { 799 offset = 0; 800 period = 0; 801 } 802 803 spi_offset(starget) = offset; 804 spi_period(starget) = period; 805 806 if(NCR_700_is_flag_set(SCp->device, NCR_700_DEV_PRINT_SYNC_NEGOTIATION)) { 807 spi_display_xfer_agreement(starget); 808 NCR_700_clear_flag(SCp->device, NCR_700_DEV_PRINT_SYNC_NEGOTIATION); 809 } 810 811 NCR_700_set_flag(SCp->device, NCR_700_DEV_NEGOTIATED_SYNC); 812 NCR_700_clear_flag(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); 813 814 NCR_700_writeb(NCR_700_get_SXFER(SCp->device), 815 host, SXFER_REG); 816 817 } else { 818 /* SDTR message out of the blue, reject it */ 819 shost_printk(KERN_WARNING, host, 820 "Unexpected SDTR msg\n"); 821 hostdata->msgout[0] = A_REJECT_MSG; 822 dma_cache_sync(hostdata->dev, hostdata->msgout, 1, DMA_TO_DEVICE); 823 script_patch_16(hostdata->dev, hostdata->script, 824 MessageCount, 1); 825 /* SendMsgOut returns, so set up the return 826 * address */ 827 resume_offset = hostdata->pScript + Ent_SendMessageWithATN; 828 } 829 break; 830 831 case A_WDTR_MSG: 832 printk(KERN_INFO "scsi%d: (%d:%d), Unsolicited WDTR after CMD, Rejecting\n", 833 host->host_no, pun, lun); 834 hostdata->msgout[0] = A_REJECT_MSG; 835 dma_cache_sync(hostdata->dev, hostdata->msgout, 1, DMA_TO_DEVICE); 836 script_patch_16(hostdata->dev, hostdata->script, MessageCount, 837 1); 838 resume_offset = hostdata->pScript + Ent_SendMessageWithATN; 839 840 break; 841 842 default: 843 printk(KERN_INFO "scsi%d (%d:%d): Unexpected message %s: ", 844 host->host_no, pun, lun, 845 NCR_700_phase[(dsps & 0xf00) >> 8]); 846 spi_print_msg(hostdata->msgin); 847 printk("\n"); 848 /* just reject it */ 849 hostdata->msgout[0] = A_REJECT_MSG; 850 dma_cache_sync(hostdata->dev, hostdata->msgout, 1, DMA_TO_DEVICE); 851 script_patch_16(hostdata->dev, hostdata->script, MessageCount, 852 1); 853 /* SendMsgOut returns, so set up the return 854 * address */ 855 resume_offset = hostdata->pScript + Ent_SendMessageWithATN; 856 } 857 NCR_700_writel(temp, host, TEMP_REG); 858 return resume_offset; 859 } 860 861 STATIC __u32 862 process_message(struct Scsi_Host *host, struct NCR_700_Host_Parameters *hostdata, 863 struct scsi_cmnd *SCp, __u32 dsp, __u32 dsps) 864 { 865 /* work out where to return to */ 866 __u32 temp = dsp + 8, resume_offset = dsp; 867 __u8 pun = 0xff, lun = 0xff; 868 869 if(SCp != NULL) { 870 pun = SCp->device->id; 871 lun = SCp->device->lun; 872 } 873 874 #ifdef NCR_700_DEBUG 875 printk("scsi%d (%d:%d): message %s: ", host->host_no, pun, lun, 876 NCR_700_phase[(dsps & 0xf00) >> 8]); 877 spi_print_msg(hostdata->msgin); 878 printk("\n"); 879 #endif 880 881 switch(hostdata->msgin[0]) { 882 883 case A_EXTENDED_MSG: 884 resume_offset = process_extended_message(host, hostdata, SCp, 885 dsp, dsps); 886 break; 887 888 case A_REJECT_MSG: 889 if(SCp != NULL && NCR_700_is_flag_set(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION)) { 890 /* Rejected our sync negotiation attempt */ 891 spi_period(SCp->device->sdev_target) = 892 spi_offset(SCp->device->sdev_target) = 0; 893 NCR_700_set_flag(SCp->device, NCR_700_DEV_NEGOTIATED_SYNC); 894 NCR_700_clear_flag(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); 895 } else if(SCp != NULL && NCR_700_get_tag_neg_state(SCp->device) == NCR_700_DURING_TAG_NEGOTIATION) { 896 /* rejected our first simple tag message */ 897 scmd_printk(KERN_WARNING, SCp, 898 "Rejected first tag queue attempt, turning off tag queueing\n"); 899 /* we're done negotiating */ 900 NCR_700_set_tag_neg_state(SCp->device, NCR_700_FINISHED_TAG_NEGOTIATION); 901 hostdata->tag_negotiated &= ~(1<<scmd_id(SCp)); 902 903 SCp->device->tagged_supported = 0; 904 SCp->device->simple_tags = 0; 905 scsi_change_queue_depth(SCp->device, host->cmd_per_lun); 906 } else { 907 shost_printk(KERN_WARNING, host, 908 "(%d:%d) Unexpected REJECT Message %s\n", 909 pun, lun, 910 NCR_700_phase[(dsps & 0xf00) >> 8]); 911 /* however, just ignore it */ 912 } 913 break; 914 915 case A_PARITY_ERROR_MSG: 916 printk(KERN_ERR "scsi%d (%d:%d) Parity Error!\n", host->host_no, 917 pun, lun); 918 NCR_700_internal_bus_reset(host); 919 break; 920 case A_SIMPLE_TAG_MSG: 921 printk(KERN_INFO "scsi%d (%d:%d) SIMPLE TAG %d %s\n", host->host_no, 922 pun, lun, hostdata->msgin[1], 923 NCR_700_phase[(dsps & 0xf00) >> 8]); 924 /* just ignore it */ 925 break; 926 default: 927 printk(KERN_INFO "scsi%d (%d:%d): Unexpected message %s: ", 928 host->host_no, pun, lun, 929 NCR_700_phase[(dsps & 0xf00) >> 8]); 930 931 spi_print_msg(hostdata->msgin); 932 printk("\n"); 933 /* just reject it */ 934 hostdata->msgout[0] = A_REJECT_MSG; 935 dma_cache_sync(hostdata->dev, hostdata->msgout, 1, DMA_TO_DEVICE); 936 script_patch_16(hostdata->dev, hostdata->script, MessageCount, 937 1); 938 /* SendMsgOut returns, so set up the return 939 * address */ 940 resume_offset = hostdata->pScript + Ent_SendMessageWithATN; 941 942 break; 943 } 944 NCR_700_writel(temp, host, TEMP_REG); 945 /* set us up to receive another message */ 946 dma_cache_sync(hostdata->dev, hostdata->msgin, MSG_ARRAY_SIZE, DMA_FROM_DEVICE); 947 return resume_offset; 948 } 949 950 STATIC __u32 951 process_script_interrupt(__u32 dsps, __u32 dsp, struct scsi_cmnd *SCp, 952 struct Scsi_Host *host, 953 struct NCR_700_Host_Parameters *hostdata) 954 { 955 __u32 resume_offset = 0; 956 __u8 pun = 0xff, lun=0xff; 957 958 if(SCp != NULL) { 959 pun = SCp->device->id; 960 lun = SCp->device->lun; 961 } 962 963 if(dsps == A_GOOD_STATUS_AFTER_STATUS) { 964 DEBUG((" COMMAND COMPLETE, status=%02x\n", 965 hostdata->status[0])); 966 /* OK, if TCQ still under negotiation, we now know it works */ 967 if (NCR_700_get_tag_neg_state(SCp->device) == NCR_700_DURING_TAG_NEGOTIATION) 968 NCR_700_set_tag_neg_state(SCp->device, 969 NCR_700_FINISHED_TAG_NEGOTIATION); 970 971 /* check for contingent allegiance contitions */ 972 if(status_byte(hostdata->status[0]) == CHECK_CONDITION || 973 status_byte(hostdata->status[0]) == COMMAND_TERMINATED) { 974 struct NCR_700_command_slot *slot = 975 (struct NCR_700_command_slot *)SCp->host_scribble; 976 if(slot->flags == NCR_700_FLAG_AUTOSENSE) { 977 /* OOPS: bad device, returning another 978 * contingent allegiance condition */ 979 scmd_printk(KERN_ERR, SCp, 980 "broken device is looping in contingent allegiance: ignoring\n"); 981 NCR_700_scsi_done(hostdata, SCp, hostdata->status[0]); 982 } else { 983 char *cmnd = 984 NCR_700_get_sense_cmnd(SCp->device); 985 #ifdef NCR_DEBUG 986 scsi_print_command(SCp); 987 printk(" cmd %p has status %d, requesting sense\n", 988 SCp, hostdata->status[0]); 989 #endif 990 /* we can destroy the command here 991 * because the contingent allegiance 992 * condition will cause a retry which 993 * will re-copy the command from the 994 * saved data_cmnd. We also unmap any 995 * data associated with the command 996 * here */ 997 NCR_700_unmap(hostdata, SCp, slot); 998 dma_unmap_single(hostdata->dev, slot->pCmd, 999 MAX_COMMAND_SIZE, 1000 DMA_TO_DEVICE); 1001 1002 cmnd[0] = REQUEST_SENSE; 1003 cmnd[1] = (lun & 0x7) << 5; 1004 cmnd[2] = 0; 1005 cmnd[3] = 0; 1006 cmnd[4] = SCSI_SENSE_BUFFERSIZE; 1007 cmnd[5] = 0; 1008 /* Here's a quiet hack: the 1009 * REQUEST_SENSE command is six bytes, 1010 * so store a flag indicating that 1011 * this was an internal sense request 1012 * and the original status at the end 1013 * of the command */ 1014 cmnd[6] = NCR_700_INTERNAL_SENSE_MAGIC; 1015 cmnd[7] = hostdata->status[0]; 1016 cmnd[8] = SCp->cmd_len; 1017 SCp->cmd_len = 6; /* command length for 1018 * REQUEST_SENSE */ 1019 slot->pCmd = dma_map_single(hostdata->dev, cmnd, MAX_COMMAND_SIZE, DMA_TO_DEVICE); 1020 slot->dma_handle = dma_map_single(hostdata->dev, SCp->sense_buffer, SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE); 1021 slot->SG[0].ins = bS_to_host(SCRIPT_MOVE_DATA_IN | SCSI_SENSE_BUFFERSIZE); 1022 slot->SG[0].pAddr = bS_to_host(slot->dma_handle); 1023 slot->SG[1].ins = bS_to_host(SCRIPT_RETURN); 1024 slot->SG[1].pAddr = 0; 1025 slot->resume_offset = hostdata->pScript; 1026 dma_cache_sync(hostdata->dev, slot->SG, sizeof(slot->SG[0])*2, DMA_TO_DEVICE); 1027 dma_cache_sync(hostdata->dev, SCp->sense_buffer, SCSI_SENSE_BUFFERSIZE, DMA_FROM_DEVICE); 1028 1029 /* queue the command for reissue */ 1030 slot->state = NCR_700_SLOT_QUEUED; 1031 slot->flags = NCR_700_FLAG_AUTOSENSE; 1032 hostdata->state = NCR_700_HOST_FREE; 1033 hostdata->cmd = NULL; 1034 } 1035 } else { 1036 // Currently rely on the mid layer evaluation 1037 // of the tag queuing capability 1038 // 1039 //if(status_byte(hostdata->status[0]) == GOOD && 1040 // SCp->cmnd[0] == INQUIRY && SCp->use_sg == 0) { 1041 // /* Piggy back the tag queueing support 1042 // * on this command */ 1043 // dma_sync_single_for_cpu(hostdata->dev, 1044 // slot->dma_handle, 1045 // SCp->request_bufflen, 1046 // DMA_FROM_DEVICE); 1047 // if(((char *)SCp->request_buffer)[7] & 0x02) { 1048 // scmd_printk(KERN_INFO, SCp, 1049 // "Enabling Tag Command Queuing\n"); 1050 // hostdata->tag_negotiated |= (1<<scmd_id(SCp)); 1051 // NCR_700_set_flag(SCp->device, NCR_700_DEV_BEGIN_TAG_QUEUEING); 1052 // } else { 1053 // NCR_700_clear_flag(SCp->device, NCR_700_DEV_BEGIN_TAG_QUEUEING); 1054 // hostdata->tag_negotiated &= ~(1<<scmd_id(SCp)); 1055 // } 1056 //} 1057 NCR_700_scsi_done(hostdata, SCp, hostdata->status[0]); 1058 } 1059 } else if((dsps & 0xfffff0f0) == A_UNEXPECTED_PHASE) { 1060 __u8 i = (dsps & 0xf00) >> 8; 1061 1062 scmd_printk(KERN_ERR, SCp, "UNEXPECTED PHASE %s (%s)\n", 1063 NCR_700_phase[i], 1064 sbcl_to_string(NCR_700_readb(host, SBCL_REG))); 1065 scmd_printk(KERN_ERR, SCp, " len = %d, cmd =", 1066 SCp->cmd_len); 1067 scsi_print_command(SCp); 1068 1069 NCR_700_internal_bus_reset(host); 1070 } else if((dsps & 0xfffff000) == A_FATAL) { 1071 int i = (dsps & 0xfff); 1072 1073 printk(KERN_ERR "scsi%d: (%d:%d) FATAL ERROR: %s\n", 1074 host->host_no, pun, lun, NCR_700_fatal_messages[i]); 1075 if(dsps == A_FATAL_ILLEGAL_MSG_LENGTH) { 1076 printk(KERN_ERR " msg begins %02x %02x\n", 1077 hostdata->msgin[0], hostdata->msgin[1]); 1078 } 1079 NCR_700_internal_bus_reset(host); 1080 } else if((dsps & 0xfffff0f0) == A_DISCONNECT) { 1081 #ifdef NCR_700_DEBUG 1082 __u8 i = (dsps & 0xf00) >> 8; 1083 1084 printk("scsi%d: (%d:%d), DISCONNECTED (%d) %s\n", 1085 host->host_no, pun, lun, 1086 i, NCR_700_phase[i]); 1087 #endif 1088 save_for_reselection(hostdata, SCp, dsp); 1089 1090 } else if(dsps == A_RESELECTION_IDENTIFIED) { 1091 __u8 lun; 1092 struct NCR_700_command_slot *slot; 1093 __u8 reselection_id = hostdata->reselection_id; 1094 struct scsi_device *SDp; 1095 1096 lun = hostdata->msgin[0] & 0x1f; 1097 1098 hostdata->reselection_id = 0xff; 1099 DEBUG(("scsi%d: (%d:%d) RESELECTED!\n", 1100 host->host_no, reselection_id, lun)); 1101 /* clear the reselection indicator */ 1102 SDp = __scsi_device_lookup(host, 0, reselection_id, lun); 1103 if(unlikely(SDp == NULL)) { 1104 printk(KERN_ERR "scsi%d: (%d:%d) HAS NO device\n", 1105 host->host_no, reselection_id, lun); 1106 BUG(); 1107 } 1108 if(hostdata->msgin[1] == A_SIMPLE_TAG_MSG) { 1109 struct scsi_cmnd *SCp; 1110 1111 SCp = scsi_host_find_tag(SDp->host, hostdata->msgin[2]); 1112 if(unlikely(SCp == NULL)) { 1113 printk(KERN_ERR "scsi%d: (%d:%d) no saved request for tag %d\n", 1114 host->host_no, reselection_id, lun, hostdata->msgin[2]); 1115 BUG(); 1116 } 1117 1118 slot = (struct NCR_700_command_slot *)SCp->host_scribble; 1119 DDEBUG(KERN_DEBUG, SDp, 1120 "reselection is tag %d, slot %p(%d)\n", 1121 hostdata->msgin[2], slot, slot->tag); 1122 } else { 1123 struct scsi_cmnd *SCp; 1124 1125 SCp = scsi_host_find_tag(SDp->host, SCSI_NO_TAG); 1126 if(unlikely(SCp == NULL)) { 1127 sdev_printk(KERN_ERR, SDp, 1128 "no saved request for untagged cmd\n"); 1129 BUG(); 1130 } 1131 slot = (struct NCR_700_command_slot *)SCp->host_scribble; 1132 } 1133 1134 if(slot == NULL) { 1135 printk(KERN_ERR "scsi%d: (%d:%d) RESELECTED but no saved command (MSG = %02x %02x %02x)!!\n", 1136 host->host_no, reselection_id, lun, 1137 hostdata->msgin[0], hostdata->msgin[1], 1138 hostdata->msgin[2]); 1139 } else { 1140 if(hostdata->state != NCR_700_HOST_BUSY) 1141 printk(KERN_ERR "scsi%d: FATAL, host not busy during valid reselection!\n", 1142 host->host_no); 1143 resume_offset = slot->resume_offset; 1144 hostdata->cmd = slot->cmnd; 1145 1146 /* re-patch for this command */ 1147 script_patch_32_abs(hostdata->dev, hostdata->script, 1148 CommandAddress, slot->pCmd); 1149 script_patch_16(hostdata->dev, hostdata->script, 1150 CommandCount, slot->cmnd->cmd_len); 1151 script_patch_32_abs(hostdata->dev, hostdata->script, 1152 SGScriptStartAddress, 1153 to32bit(&slot->pSG[0].ins)); 1154 1155 /* Note: setting SXFER only works if we're 1156 * still in the MESSAGE phase, so it is vital 1157 * that ACK is still asserted when we process 1158 * the reselection message. The resume offset 1159 * should therefore always clear ACK */ 1160 NCR_700_writeb(NCR_700_get_SXFER(hostdata->cmd->device), 1161 host, SXFER_REG); 1162 dma_cache_sync(hostdata->dev, hostdata->msgin, 1163 MSG_ARRAY_SIZE, DMA_FROM_DEVICE); 1164 dma_cache_sync(hostdata->dev, hostdata->msgout, 1165 MSG_ARRAY_SIZE, DMA_TO_DEVICE); 1166 /* I'm just being paranoid here, the command should 1167 * already have been flushed from the cache */ 1168 dma_cache_sync(hostdata->dev, slot->cmnd->cmnd, 1169 slot->cmnd->cmd_len, DMA_TO_DEVICE); 1170 1171 1172 1173 } 1174 } else if(dsps == A_RESELECTED_DURING_SELECTION) { 1175 1176 /* This section is full of debugging code because I've 1177 * never managed to reach it. I think what happens is 1178 * that, because the 700 runs with selection 1179 * interrupts enabled the whole time that we take a 1180 * selection interrupt before we manage to get to the 1181 * reselected script interrupt */ 1182 1183 __u8 reselection_id = NCR_700_readb(host, SFBR_REG); 1184 struct NCR_700_command_slot *slot; 1185 1186 /* Take out our own ID */ 1187 reselection_id &= ~(1<<host->this_id); 1188 1189 /* I've never seen this happen, so keep this as a printk rather 1190 * than a debug */ 1191 printk(KERN_INFO "scsi%d: (%d:%d) RESELECTION DURING SELECTION, dsp=%08x[%04x] state=%d, count=%d\n", 1192 host->host_no, reselection_id, lun, dsp, dsp - hostdata->pScript, hostdata->state, hostdata->command_slot_count); 1193 1194 { 1195 /* FIXME: DEBUGGING CODE */ 1196 __u32 SG = (__u32)bS_to_cpu(hostdata->script[A_SGScriptStartAddress_used[0]]); 1197 int i; 1198 1199 for(i=0; i< NCR_700_COMMAND_SLOTS_PER_HOST; i++) { 1200 if(SG >= to32bit(&hostdata->slots[i].pSG[0]) 1201 && SG <= to32bit(&hostdata->slots[i].pSG[NCR_700_SG_SEGMENTS])) 1202 break; 1203 } 1204 printk(KERN_INFO "IDENTIFIED SG segment as being %08x in slot %p, cmd %p, slot->resume_offset=%08x\n", SG, &hostdata->slots[i], hostdata->slots[i].cmnd, hostdata->slots[i].resume_offset); 1205 SCp = hostdata->slots[i].cmnd; 1206 } 1207 1208 if(SCp != NULL) { 1209 slot = (struct NCR_700_command_slot *)SCp->host_scribble; 1210 /* change slot from busy to queued to redo command */ 1211 slot->state = NCR_700_SLOT_QUEUED; 1212 } 1213 hostdata->cmd = NULL; 1214 1215 if(reselection_id == 0) { 1216 if(hostdata->reselection_id == 0xff) { 1217 printk(KERN_ERR "scsi%d: Invalid reselection during selection!!\n", host->host_no); 1218 return 0; 1219 } else { 1220 printk(KERN_ERR "scsi%d: script reselected and we took a selection interrupt\n", 1221 host->host_no); 1222 reselection_id = hostdata->reselection_id; 1223 } 1224 } else { 1225 1226 /* convert to real ID */ 1227 reselection_id = bitmap_to_number(reselection_id); 1228 } 1229 hostdata->reselection_id = reselection_id; 1230 /* just in case we have a stale simple tag message, clear it */ 1231 hostdata->msgin[1] = 0; 1232 dma_cache_sync(hostdata->dev, hostdata->msgin, 1233 MSG_ARRAY_SIZE, DMA_BIDIRECTIONAL); 1234 if(hostdata->tag_negotiated & (1<<reselection_id)) { 1235 resume_offset = hostdata->pScript + Ent_GetReselectionWithTag; 1236 } else { 1237 resume_offset = hostdata->pScript + Ent_GetReselectionData; 1238 } 1239 } else if(dsps == A_COMPLETED_SELECTION_AS_TARGET) { 1240 /* we've just disconnected from the bus, do nothing since 1241 * a return here will re-run the queued command slot 1242 * that may have been interrupted by the initial selection */ 1243 DEBUG((" SELECTION COMPLETED\n")); 1244 } else if((dsps & 0xfffff0f0) == A_MSG_IN) { 1245 resume_offset = process_message(host, hostdata, SCp, 1246 dsp, dsps); 1247 } else if((dsps & 0xfffff000) == 0) { 1248 __u8 i = (dsps & 0xf0) >> 4, j = (dsps & 0xf00) >> 8; 1249 printk(KERN_ERR "scsi%d: (%d:%d), unhandled script condition %s %s at %04x\n", 1250 host->host_no, pun, lun, NCR_700_condition[i], 1251 NCR_700_phase[j], dsp - hostdata->pScript); 1252 if(SCp != NULL) { 1253 struct scatterlist *sg; 1254 1255 scsi_print_command(SCp); 1256 scsi_for_each_sg(SCp, sg, scsi_sg_count(SCp) + 1, i) { 1257 printk(KERN_INFO " SG[%d].length = %d, move_insn=%08x, addr %08x\n", i, sg->length, ((struct NCR_700_command_slot *)SCp->host_scribble)->SG[i].ins, ((struct NCR_700_command_slot *)SCp->host_scribble)->SG[i].pAddr); 1258 } 1259 } 1260 NCR_700_internal_bus_reset(host); 1261 } else if((dsps & 0xfffff000) == A_DEBUG_INTERRUPT) { 1262 printk(KERN_NOTICE "scsi%d (%d:%d) DEBUG INTERRUPT %d AT %08x[%04x], continuing\n", 1263 host->host_no, pun, lun, dsps & 0xfff, dsp, dsp - hostdata->pScript); 1264 resume_offset = dsp; 1265 } else { 1266 printk(KERN_ERR "scsi%d: (%d:%d), unidentified script interrupt 0x%x at %04x\n", 1267 host->host_no, pun, lun, dsps, dsp - hostdata->pScript); 1268 NCR_700_internal_bus_reset(host); 1269 } 1270 return resume_offset; 1271 } 1272 1273 /* We run the 53c700 with selection interrupts always enabled. This 1274 * means that the chip may be selected as soon as the bus frees. On a 1275 * busy bus, this can be before the scripts engine finishes its 1276 * processing. Therefore, part of the selection processing has to be 1277 * to find out what the scripts engine is doing and complete the 1278 * function if necessary (i.e. process the pending disconnect or save 1279 * the interrupted initial selection */ 1280 STATIC inline __u32 1281 process_selection(struct Scsi_Host *host, __u32 dsp) 1282 { 1283 __u8 id = 0; /* Squash compiler warning */ 1284 int count = 0; 1285 __u32 resume_offset = 0; 1286 struct NCR_700_Host_Parameters *hostdata = 1287 (struct NCR_700_Host_Parameters *)host->hostdata[0]; 1288 struct scsi_cmnd *SCp = hostdata->cmd; 1289 __u8 sbcl; 1290 1291 for(count = 0; count < 5; count++) { 1292 id = NCR_700_readb(host, hostdata->chip710 ? 1293 CTEST9_REG : SFBR_REG); 1294 1295 /* Take out our own ID */ 1296 id &= ~(1<<host->this_id); 1297 if(id != 0) 1298 break; 1299 udelay(5); 1300 } 1301 sbcl = NCR_700_readb(host, SBCL_REG); 1302 if((sbcl & SBCL_IO) == 0) { 1303 /* mark as having been selected rather than reselected */ 1304 id = 0xff; 1305 } else { 1306 /* convert to real ID */ 1307 hostdata->reselection_id = id = bitmap_to_number(id); 1308 DEBUG(("scsi%d: Reselected by %d\n", 1309 host->host_no, id)); 1310 } 1311 if(hostdata->state == NCR_700_HOST_BUSY && SCp != NULL) { 1312 struct NCR_700_command_slot *slot = 1313 (struct NCR_700_command_slot *)SCp->host_scribble; 1314 DEBUG((" ID %d WARNING: RESELECTION OF BUSY HOST, saving cmd %p, slot %p, addr %x [%04x], resume %x!\n", id, hostdata->cmd, slot, dsp, dsp - hostdata->pScript, resume_offset)); 1315 1316 switch(dsp - hostdata->pScript) { 1317 case Ent_Disconnect1: 1318 case Ent_Disconnect2: 1319 save_for_reselection(hostdata, SCp, Ent_Disconnect2 + hostdata->pScript); 1320 break; 1321 case Ent_Disconnect3: 1322 case Ent_Disconnect4: 1323 save_for_reselection(hostdata, SCp, Ent_Disconnect4 + hostdata->pScript); 1324 break; 1325 case Ent_Disconnect5: 1326 case Ent_Disconnect6: 1327 save_for_reselection(hostdata, SCp, Ent_Disconnect6 + hostdata->pScript); 1328 break; 1329 case Ent_Disconnect7: 1330 case Ent_Disconnect8: 1331 save_for_reselection(hostdata, SCp, Ent_Disconnect8 + hostdata->pScript); 1332 break; 1333 case Ent_Finish1: 1334 case Ent_Finish2: 1335 process_script_interrupt(A_GOOD_STATUS_AFTER_STATUS, dsp, SCp, host, hostdata); 1336 break; 1337 1338 default: 1339 slot->state = NCR_700_SLOT_QUEUED; 1340 break; 1341 } 1342 } 1343 hostdata->state = NCR_700_HOST_BUSY; 1344 hostdata->cmd = NULL; 1345 /* clear any stale simple tag message */ 1346 hostdata->msgin[1] = 0; 1347 dma_cache_sync(hostdata->dev, hostdata->msgin, MSG_ARRAY_SIZE, 1348 DMA_BIDIRECTIONAL); 1349 1350 if(id == 0xff) { 1351 /* Selected as target, Ignore */ 1352 resume_offset = hostdata->pScript + Ent_SelectedAsTarget; 1353 } else if(hostdata->tag_negotiated & (1<<id)) { 1354 resume_offset = hostdata->pScript + Ent_GetReselectionWithTag; 1355 } else { 1356 resume_offset = hostdata->pScript + Ent_GetReselectionData; 1357 } 1358 return resume_offset; 1359 } 1360 1361 static inline void 1362 NCR_700_clear_fifo(struct Scsi_Host *host) { 1363 const struct NCR_700_Host_Parameters *hostdata 1364 = (struct NCR_700_Host_Parameters *)host->hostdata[0]; 1365 if(hostdata->chip710) { 1366 NCR_700_writeb(CLR_FIFO_710, host, CTEST8_REG); 1367 } else { 1368 NCR_700_writeb(CLR_FIFO, host, DFIFO_REG); 1369 } 1370 } 1371 1372 static inline void 1373 NCR_700_flush_fifo(struct Scsi_Host *host) { 1374 const struct NCR_700_Host_Parameters *hostdata 1375 = (struct NCR_700_Host_Parameters *)host->hostdata[0]; 1376 if(hostdata->chip710) { 1377 NCR_700_writeb(FLUSH_DMA_FIFO_710, host, CTEST8_REG); 1378 udelay(10); 1379 NCR_700_writeb(0, host, CTEST8_REG); 1380 } else { 1381 NCR_700_writeb(FLUSH_DMA_FIFO, host, DFIFO_REG); 1382 udelay(10); 1383 NCR_700_writeb(0, host, DFIFO_REG); 1384 } 1385 } 1386 1387 1388 /* The queue lock with interrupts disabled must be held on entry to 1389 * this function */ 1390 STATIC int 1391 NCR_700_start_command(struct scsi_cmnd *SCp) 1392 { 1393 struct NCR_700_command_slot *slot = 1394 (struct NCR_700_command_slot *)SCp->host_scribble; 1395 struct NCR_700_Host_Parameters *hostdata = 1396 (struct NCR_700_Host_Parameters *)SCp->device->host->hostdata[0]; 1397 __u16 count = 1; /* for IDENTIFY message */ 1398 u8 lun = SCp->device->lun; 1399 1400 if(hostdata->state != NCR_700_HOST_FREE) { 1401 /* keep this inside the lock to close the race window where 1402 * the running command finishes on another CPU while we don't 1403 * change the state to queued on this one */ 1404 slot->state = NCR_700_SLOT_QUEUED; 1405 1406 DEBUG(("scsi%d: host busy, queueing command %p, slot %p\n", 1407 SCp->device->host->host_no, slot->cmnd, slot)); 1408 return 0; 1409 } 1410 hostdata->state = NCR_700_HOST_BUSY; 1411 hostdata->cmd = SCp; 1412 slot->state = NCR_700_SLOT_BUSY; 1413 /* keep interrupts disabled until we have the command correctly 1414 * set up so we cannot take a selection interrupt */ 1415 1416 hostdata->msgout[0] = NCR_700_identify((SCp->cmnd[0] != REQUEST_SENSE && 1417 slot->flags != NCR_700_FLAG_AUTOSENSE), 1418 lun); 1419 /* for INQUIRY or REQUEST_SENSE commands, we cannot be sure 1420 * if the negotiated transfer parameters still hold, so 1421 * always renegotiate them */ 1422 if(SCp->cmnd[0] == INQUIRY || SCp->cmnd[0] == REQUEST_SENSE || 1423 slot->flags == NCR_700_FLAG_AUTOSENSE) { 1424 NCR_700_clear_flag(SCp->device, NCR_700_DEV_NEGOTIATED_SYNC); 1425 } 1426 1427 /* REQUEST_SENSE is asking for contingent I_T_L(_Q) status. 1428 * If a contingent allegiance condition exists, the device 1429 * will refuse all tags, so send the request sense as untagged 1430 * */ 1431 if((hostdata->tag_negotiated & (1<<scmd_id(SCp))) 1432 && (slot->tag != SCSI_NO_TAG && SCp->cmnd[0] != REQUEST_SENSE && 1433 slot->flags != NCR_700_FLAG_AUTOSENSE)) { 1434 count += spi_populate_tag_msg(&hostdata->msgout[count], SCp); 1435 } 1436 1437 if(hostdata->fast && 1438 NCR_700_is_flag_clear(SCp->device, NCR_700_DEV_NEGOTIATED_SYNC)) { 1439 count += spi_populate_sync_msg(&hostdata->msgout[count], 1440 spi_period(SCp->device->sdev_target), 1441 spi_offset(SCp->device->sdev_target)); 1442 NCR_700_set_flag(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); 1443 } 1444 1445 script_patch_16(hostdata->dev, hostdata->script, MessageCount, count); 1446 1447 1448 script_patch_ID(hostdata->dev, hostdata->script, 1449 Device_ID, 1<<scmd_id(SCp)); 1450 1451 script_patch_32_abs(hostdata->dev, hostdata->script, CommandAddress, 1452 slot->pCmd); 1453 script_patch_16(hostdata->dev, hostdata->script, CommandCount, 1454 SCp->cmd_len); 1455 /* finally plumb the beginning of the SG list into the script 1456 * */ 1457 script_patch_32_abs(hostdata->dev, hostdata->script, 1458 SGScriptStartAddress, to32bit(&slot->pSG[0].ins)); 1459 NCR_700_clear_fifo(SCp->device->host); 1460 1461 if(slot->resume_offset == 0) 1462 slot->resume_offset = hostdata->pScript; 1463 /* now perform all the writebacks and invalidates */ 1464 dma_cache_sync(hostdata->dev, hostdata->msgout, count, DMA_TO_DEVICE); 1465 dma_cache_sync(hostdata->dev, hostdata->msgin, MSG_ARRAY_SIZE, 1466 DMA_FROM_DEVICE); 1467 dma_cache_sync(hostdata->dev, SCp->cmnd, SCp->cmd_len, DMA_TO_DEVICE); 1468 dma_cache_sync(hostdata->dev, hostdata->status, 1, DMA_FROM_DEVICE); 1469 1470 /* set the synchronous period/offset */ 1471 NCR_700_writeb(NCR_700_get_SXFER(SCp->device), 1472 SCp->device->host, SXFER_REG); 1473 NCR_700_writel(slot->temp, SCp->device->host, TEMP_REG); 1474 NCR_700_writel(slot->resume_offset, SCp->device->host, DSP_REG); 1475 1476 return 1; 1477 } 1478 1479 irqreturn_t 1480 NCR_700_intr(int irq, void *dev_id) 1481 { 1482 struct Scsi_Host *host = (struct Scsi_Host *)dev_id; 1483 struct NCR_700_Host_Parameters *hostdata = 1484 (struct NCR_700_Host_Parameters *)host->hostdata[0]; 1485 __u8 istat; 1486 __u32 resume_offset = 0; 1487 __u8 pun = 0xff, lun = 0xff; 1488 unsigned long flags; 1489 int handled = 0; 1490 1491 /* Use the host lock to serialise access to the 53c700 1492 * hardware. Note: In future, we may need to take the queue 1493 * lock to enter the done routines. When that happens, we 1494 * need to ensure that for this driver, the host lock and the 1495 * queue lock point to the same thing. */ 1496 spin_lock_irqsave(host->host_lock, flags); 1497 if((istat = NCR_700_readb(host, ISTAT_REG)) 1498 & (SCSI_INT_PENDING | DMA_INT_PENDING)) { 1499 __u32 dsps; 1500 __u8 sstat0 = 0, dstat = 0; 1501 __u32 dsp; 1502 struct scsi_cmnd *SCp = hostdata->cmd; 1503 enum NCR_700_Host_State state; 1504 1505 handled = 1; 1506 state = hostdata->state; 1507 SCp = hostdata->cmd; 1508 1509 if(istat & SCSI_INT_PENDING) { 1510 udelay(10); 1511 1512 sstat0 = NCR_700_readb(host, SSTAT0_REG); 1513 } 1514 1515 if(istat & DMA_INT_PENDING) { 1516 udelay(10); 1517 1518 dstat = NCR_700_readb(host, DSTAT_REG); 1519 } 1520 1521 dsps = NCR_700_readl(host, DSPS_REG); 1522 dsp = NCR_700_readl(host, DSP_REG); 1523 1524 DEBUG(("scsi%d: istat %02x sstat0 %02x dstat %02x dsp %04x[%08x] dsps 0x%x\n", 1525 host->host_no, istat, sstat0, dstat, 1526 (dsp - (__u32)(hostdata->pScript))/4, 1527 dsp, dsps)); 1528 1529 if(SCp != NULL) { 1530 pun = SCp->device->id; 1531 lun = SCp->device->lun; 1532 } 1533 1534 if(sstat0 & SCSI_RESET_DETECTED) { 1535 struct scsi_device *SDp; 1536 int i; 1537 1538 hostdata->state = NCR_700_HOST_BUSY; 1539 1540 printk(KERN_ERR "scsi%d: Bus Reset detected, executing command %p, slot %p, dsp %08x[%04x]\n", 1541 host->host_no, SCp, SCp == NULL ? NULL : SCp->host_scribble, dsp, dsp - hostdata->pScript); 1542 1543 scsi_report_bus_reset(host, 0); 1544 1545 /* clear all the negotiated parameters */ 1546 __shost_for_each_device(SDp, host) 1547 NCR_700_clear_flag(SDp, ~0); 1548 1549 /* clear all the slots and their pending commands */ 1550 for(i = 0; i < NCR_700_COMMAND_SLOTS_PER_HOST; i++) { 1551 struct scsi_cmnd *SCp; 1552 struct NCR_700_command_slot *slot = 1553 &hostdata->slots[i]; 1554 1555 if(slot->state == NCR_700_SLOT_FREE) 1556 continue; 1557 1558 SCp = slot->cmnd; 1559 printk(KERN_ERR " failing command because of reset, slot %p, cmnd %p\n", 1560 slot, SCp); 1561 free_slot(slot, hostdata); 1562 SCp->host_scribble = NULL; 1563 NCR_700_set_depth(SCp->device, 0); 1564 /* NOTE: deadlock potential here: we 1565 * rely on mid-layer guarantees that 1566 * scsi_done won't try to issue the 1567 * command again otherwise we'll 1568 * deadlock on the 1569 * hostdata->state_lock */ 1570 SCp->result = DID_RESET << 16; 1571 SCp->scsi_done(SCp); 1572 } 1573 mdelay(25); 1574 NCR_700_chip_setup(host); 1575 1576 hostdata->state = NCR_700_HOST_FREE; 1577 hostdata->cmd = NULL; 1578 /* signal back if this was an eh induced reset */ 1579 if(hostdata->eh_complete != NULL) 1580 complete(hostdata->eh_complete); 1581 goto out_unlock; 1582 } else if(sstat0 & SELECTION_TIMEOUT) { 1583 DEBUG(("scsi%d: (%d:%d) selection timeout\n", 1584 host->host_no, pun, lun)); 1585 NCR_700_scsi_done(hostdata, SCp, DID_NO_CONNECT<<16); 1586 } else if(sstat0 & PHASE_MISMATCH) { 1587 struct NCR_700_command_slot *slot = (SCp == NULL) ? NULL : 1588 (struct NCR_700_command_slot *)SCp->host_scribble; 1589 1590 if(dsp == Ent_SendMessage + 8 + hostdata->pScript) { 1591 /* It wants to reply to some part of 1592 * our message */ 1593 #ifdef NCR_700_DEBUG 1594 __u32 temp = NCR_700_readl(host, TEMP_REG); 1595 int count = (hostdata->script[Ent_SendMessage/4] & 0xffffff) - ((NCR_700_readl(host, DBC_REG) & 0xffffff) + NCR_700_data_residual(host)); 1596 printk("scsi%d (%d:%d) PHASE MISMATCH IN SEND MESSAGE %d remain, return %p[%04x], phase %s\n", host->host_no, pun, lun, count, (void *)temp, temp - hostdata->pScript, sbcl_to_string(NCR_700_readb(host, SBCL_REG))); 1597 #endif 1598 resume_offset = hostdata->pScript + Ent_SendMessagePhaseMismatch; 1599 } else if(dsp >= to32bit(&slot->pSG[0].ins) && 1600 dsp <= to32bit(&slot->pSG[NCR_700_SG_SEGMENTS].ins)) { 1601 int data_transfer = NCR_700_readl(host, DBC_REG) & 0xffffff; 1602 int SGcount = (dsp - to32bit(&slot->pSG[0].ins))/sizeof(struct NCR_700_SG_List); 1603 int residual = NCR_700_data_residual(host); 1604 int i; 1605 #ifdef NCR_700_DEBUG 1606 __u32 naddr = NCR_700_readl(host, DNAD_REG); 1607 1608 printk("scsi%d: (%d:%d) Expected phase mismatch in slot->SG[%d], transferred 0x%x\n", 1609 host->host_no, pun, lun, 1610 SGcount, data_transfer); 1611 scsi_print_command(SCp); 1612 if(residual) { 1613 printk("scsi%d: (%d:%d) Expected phase mismatch in slot->SG[%d], transferred 0x%x, residual %d\n", 1614 host->host_no, pun, lun, 1615 SGcount, data_transfer, residual); 1616 } 1617 #endif 1618 data_transfer += residual; 1619 1620 if(data_transfer != 0) { 1621 int count; 1622 __u32 pAddr; 1623 1624 SGcount--; 1625 1626 count = (bS_to_cpu(slot->SG[SGcount].ins) & 0x00ffffff); 1627 DEBUG(("DATA TRANSFER MISMATCH, count = %d, transferred %d\n", count, count-data_transfer)); 1628 slot->SG[SGcount].ins &= bS_to_host(0xff000000); 1629 slot->SG[SGcount].ins |= bS_to_host(data_transfer); 1630 pAddr = bS_to_cpu(slot->SG[SGcount].pAddr); 1631 pAddr += (count - data_transfer); 1632 #ifdef NCR_700_DEBUG 1633 if(pAddr != naddr) { 1634 printk("scsi%d (%d:%d) transfer mismatch pAddr=%lx, naddr=%lx, data_transfer=%d, residual=%d\n", host->host_no, pun, lun, (unsigned long)pAddr, (unsigned long)naddr, data_transfer, residual); 1635 } 1636 #endif 1637 slot->SG[SGcount].pAddr = bS_to_host(pAddr); 1638 } 1639 /* set the executed moves to nops */ 1640 for(i=0; i<SGcount; i++) { 1641 slot->SG[i].ins = bS_to_host(SCRIPT_NOP); 1642 slot->SG[i].pAddr = 0; 1643 } 1644 dma_cache_sync(hostdata->dev, slot->SG, sizeof(slot->SG), DMA_TO_DEVICE); 1645 /* and pretend we disconnected after 1646 * the command phase */ 1647 resume_offset = hostdata->pScript + Ent_MsgInDuringData; 1648 /* make sure all the data is flushed */ 1649 NCR_700_flush_fifo(host); 1650 } else { 1651 __u8 sbcl = NCR_700_readb(host, SBCL_REG); 1652 printk(KERN_ERR "scsi%d: (%d:%d) phase mismatch at %04x, phase %s\n", 1653 host->host_no, pun, lun, dsp - hostdata->pScript, sbcl_to_string(sbcl)); 1654 NCR_700_internal_bus_reset(host); 1655 } 1656 1657 } else if(sstat0 & SCSI_GROSS_ERROR) { 1658 printk(KERN_ERR "scsi%d: (%d:%d) GROSS ERROR\n", 1659 host->host_no, pun, lun); 1660 NCR_700_scsi_done(hostdata, SCp, DID_ERROR<<16); 1661 } else if(sstat0 & PARITY_ERROR) { 1662 printk(KERN_ERR "scsi%d: (%d:%d) PARITY ERROR\n", 1663 host->host_no, pun, lun); 1664 NCR_700_scsi_done(hostdata, SCp, DID_ERROR<<16); 1665 } else if(dstat & SCRIPT_INT_RECEIVED) { 1666 DEBUG(("scsi%d: (%d:%d) ====>SCRIPT INTERRUPT<====\n", 1667 host->host_no, pun, lun)); 1668 resume_offset = process_script_interrupt(dsps, dsp, SCp, host, hostdata); 1669 } else if(dstat & (ILGL_INST_DETECTED)) { 1670 printk(KERN_ERR "scsi%d: (%d:%d) Illegal Instruction detected at 0x%08x[0x%x]!!!\n" 1671 " Please email James.Bottomley@HansenPartnership.com with the details\n", 1672 host->host_no, pun, lun, 1673 dsp, dsp - hostdata->pScript); 1674 NCR_700_scsi_done(hostdata, SCp, DID_ERROR<<16); 1675 } else if(dstat & (WATCH_DOG_INTERRUPT|ABORTED)) { 1676 printk(KERN_ERR "scsi%d: (%d:%d) serious DMA problem, dstat=%02x\n", 1677 host->host_no, pun, lun, dstat); 1678 NCR_700_scsi_done(hostdata, SCp, DID_ERROR<<16); 1679 } 1680 1681 1682 /* NOTE: selection interrupt processing MUST occur 1683 * after script interrupt processing to correctly cope 1684 * with the case where we process a disconnect and 1685 * then get reselected before we process the 1686 * disconnection */ 1687 if(sstat0 & SELECTED) { 1688 /* FIXME: It currently takes at least FOUR 1689 * interrupts to complete a command that 1690 * disconnects: one for the disconnect, one 1691 * for the reselection, one to get the 1692 * reselection data and one to complete the 1693 * command. If we guess the reselected 1694 * command here and prepare it, we only need 1695 * to get a reselection data interrupt if we 1696 * guessed wrongly. Since the interrupt 1697 * overhead is much greater than the command 1698 * setup, this would be an efficient 1699 * optimisation particularly as we probably 1700 * only have one outstanding command on a 1701 * target most of the time */ 1702 1703 resume_offset = process_selection(host, dsp); 1704 1705 } 1706 1707 } 1708 1709 if(resume_offset) { 1710 if(hostdata->state != NCR_700_HOST_BUSY) { 1711 printk(KERN_ERR "scsi%d: Driver error: resume at 0x%08x [0x%04x] with non busy host!\n", 1712 host->host_no, resume_offset, resume_offset - hostdata->pScript); 1713 hostdata->state = NCR_700_HOST_BUSY; 1714 } 1715 1716 DEBUG(("Attempting to resume at %x\n", resume_offset)); 1717 NCR_700_clear_fifo(host); 1718 NCR_700_writel(resume_offset, host, DSP_REG); 1719 } 1720 /* There is probably a technical no-no about this: If we're a 1721 * shared interrupt and we got this interrupt because the 1722 * other device needs servicing not us, we're still going to 1723 * check our queued commands here---of course, there shouldn't 1724 * be any outstanding.... */ 1725 if(hostdata->state == NCR_700_HOST_FREE) { 1726 int i; 1727 1728 for(i = 0; i < NCR_700_COMMAND_SLOTS_PER_HOST; i++) { 1729 /* fairness: always run the queue from the last 1730 * position we left off */ 1731 int j = (i + hostdata->saved_slot_position) 1732 % NCR_700_COMMAND_SLOTS_PER_HOST; 1733 1734 if(hostdata->slots[j].state != NCR_700_SLOT_QUEUED) 1735 continue; 1736 if(NCR_700_start_command(hostdata->slots[j].cmnd)) { 1737 DEBUG(("scsi%d: Issuing saved command slot %p, cmd %p\t\n", 1738 host->host_no, &hostdata->slots[j], 1739 hostdata->slots[j].cmnd)); 1740 hostdata->saved_slot_position = j + 1; 1741 } 1742 1743 break; 1744 } 1745 } 1746 out_unlock: 1747 spin_unlock_irqrestore(host->host_lock, flags); 1748 return IRQ_RETVAL(handled); 1749 } 1750 1751 static int 1752 NCR_700_queuecommand_lck(struct scsi_cmnd *SCp, void (*done)(struct scsi_cmnd *)) 1753 { 1754 struct NCR_700_Host_Parameters *hostdata = 1755 (struct NCR_700_Host_Parameters *)SCp->device->host->hostdata[0]; 1756 __u32 move_ins; 1757 enum dma_data_direction direction; 1758 struct NCR_700_command_slot *slot; 1759 1760 if(hostdata->command_slot_count >= NCR_700_COMMAND_SLOTS_PER_HOST) { 1761 /* We're over our allocation, this should never happen 1762 * since we report the max allocation to the mid layer */ 1763 printk(KERN_WARNING "scsi%d: Command depth has gone over queue depth\n", SCp->device->host->host_no); 1764 return 1; 1765 } 1766 /* check for untagged commands. We cannot have any outstanding 1767 * commands if we accept them. Commands could be untagged because: 1768 * 1769 * - The tag negotiated bitmap is clear 1770 * - The blk layer sent and untagged command 1771 */ 1772 if(NCR_700_get_depth(SCp->device) != 0 1773 && (!(hostdata->tag_negotiated & (1<<scmd_id(SCp))) 1774 || !(SCp->flags & SCMD_TAGGED))) { 1775 CDEBUG(KERN_ERR, SCp, "has non zero depth %d\n", 1776 NCR_700_get_depth(SCp->device)); 1777 return SCSI_MLQUEUE_DEVICE_BUSY; 1778 } 1779 if(NCR_700_get_depth(SCp->device) >= SCp->device->queue_depth) { 1780 CDEBUG(KERN_ERR, SCp, "has max tag depth %d\n", 1781 NCR_700_get_depth(SCp->device)); 1782 return SCSI_MLQUEUE_DEVICE_BUSY; 1783 } 1784 NCR_700_set_depth(SCp->device, NCR_700_get_depth(SCp->device) + 1); 1785 1786 /* begin the command here */ 1787 /* no need to check for NULL, test for command_slot_count above 1788 * ensures a slot is free */ 1789 slot = find_empty_slot(hostdata); 1790 1791 slot->cmnd = SCp; 1792 1793 SCp->scsi_done = done; 1794 SCp->host_scribble = (unsigned char *)slot; 1795 SCp->SCp.ptr = NULL; 1796 SCp->SCp.buffer = NULL; 1797 1798 #ifdef NCR_700_DEBUG 1799 printk("53c700: scsi%d, command ", SCp->device->host->host_no); 1800 scsi_print_command(SCp); 1801 #endif 1802 if ((SCp->flags & SCMD_TAGGED) 1803 && (hostdata->tag_negotiated &(1<<scmd_id(SCp))) == 0 1804 && NCR_700_get_tag_neg_state(SCp->device) == NCR_700_START_TAG_NEGOTIATION) { 1805 scmd_printk(KERN_ERR, SCp, "Enabling Tag Command Queuing\n"); 1806 hostdata->tag_negotiated |= (1<<scmd_id(SCp)); 1807 NCR_700_set_tag_neg_state(SCp->device, NCR_700_DURING_TAG_NEGOTIATION); 1808 } 1809 1810 /* here we may have to process an untagged command. The gate 1811 * above ensures that this will be the only one outstanding, 1812 * so clear the tag negotiated bit. 1813 * 1814 * FIXME: This will royally screw up on multiple LUN devices 1815 * */ 1816 if (!(SCp->flags & SCMD_TAGGED) 1817 && (hostdata->tag_negotiated &(1<<scmd_id(SCp)))) { 1818 scmd_printk(KERN_INFO, SCp, "Disabling Tag Command Queuing\n"); 1819 hostdata->tag_negotiated &= ~(1<<scmd_id(SCp)); 1820 } 1821 1822 if ((hostdata->tag_negotiated & (1<<scmd_id(SCp))) && 1823 SCp->device->simple_tags) { 1824 slot->tag = SCp->request->tag; 1825 CDEBUG(KERN_DEBUG, SCp, "sending out tag %d, slot %p\n", 1826 slot->tag, slot); 1827 } else { 1828 slot->tag = SCSI_NO_TAG; 1829 /* must populate current_cmnd for scsi_host_find_tag to work */ 1830 SCp->device->current_cmnd = SCp; 1831 } 1832 /* sanity check: some of the commands generated by the mid-layer 1833 * have an eccentric idea of their sc_data_direction */ 1834 if(!scsi_sg_count(SCp) && !scsi_bufflen(SCp) && 1835 SCp->sc_data_direction != DMA_NONE) { 1836 #ifdef NCR_700_DEBUG 1837 printk("53c700: Command"); 1838 scsi_print_command(SCp); 1839 printk("Has wrong data direction %d\n", SCp->sc_data_direction); 1840 #endif 1841 SCp->sc_data_direction = DMA_NONE; 1842 } 1843 1844 switch (SCp->cmnd[0]) { 1845 case REQUEST_SENSE: 1846 /* clear the internal sense magic */ 1847 SCp->cmnd[6] = 0; 1848 /* fall through */ 1849 default: 1850 /* OK, get it from the command */ 1851 switch(SCp->sc_data_direction) { 1852 case DMA_BIDIRECTIONAL: 1853 default: 1854 printk(KERN_ERR "53c700: Unknown command for data direction "); 1855 scsi_print_command(SCp); 1856 1857 move_ins = 0; 1858 break; 1859 case DMA_NONE: 1860 move_ins = 0; 1861 break; 1862 case DMA_FROM_DEVICE: 1863 move_ins = SCRIPT_MOVE_DATA_IN; 1864 break; 1865 case DMA_TO_DEVICE: 1866 move_ins = SCRIPT_MOVE_DATA_OUT; 1867 break; 1868 } 1869 } 1870 1871 /* now build the scatter gather list */ 1872 direction = SCp->sc_data_direction; 1873 if(move_ins != 0) { 1874 int i; 1875 int sg_count; 1876 dma_addr_t vPtr = 0; 1877 struct scatterlist *sg; 1878 __u32 count = 0; 1879 1880 sg_count = scsi_dma_map(SCp); 1881 BUG_ON(sg_count < 0); 1882 1883 scsi_for_each_sg(SCp, sg, sg_count, i) { 1884 vPtr = sg_dma_address(sg); 1885 count = sg_dma_len(sg); 1886 1887 slot->SG[i].ins = bS_to_host(move_ins | count); 1888 DEBUG((" scatter block %d: move %d[%08x] from 0x%lx\n", 1889 i, count, slot->SG[i].ins, (unsigned long)vPtr)); 1890 slot->SG[i].pAddr = bS_to_host(vPtr); 1891 } 1892 slot->SG[i].ins = bS_to_host(SCRIPT_RETURN); 1893 slot->SG[i].pAddr = 0; 1894 dma_cache_sync(hostdata->dev, slot->SG, sizeof(slot->SG), DMA_TO_DEVICE); 1895 DEBUG((" SETTING %08lx to %x\n", 1896 (&slot->pSG[i].ins), 1897 slot->SG[i].ins)); 1898 } 1899 slot->resume_offset = 0; 1900 slot->pCmd = dma_map_single(hostdata->dev, SCp->cmnd, 1901 MAX_COMMAND_SIZE, DMA_TO_DEVICE); 1902 NCR_700_start_command(SCp); 1903 return 0; 1904 } 1905 1906 STATIC DEF_SCSI_QCMD(NCR_700_queuecommand) 1907 1908 STATIC int 1909 NCR_700_abort(struct scsi_cmnd * SCp) 1910 { 1911 struct NCR_700_command_slot *slot; 1912 1913 scmd_printk(KERN_INFO, SCp, "abort command\n"); 1914 1915 slot = (struct NCR_700_command_slot *)SCp->host_scribble; 1916 1917 if(slot == NULL) 1918 /* no outstanding command to abort */ 1919 return SUCCESS; 1920 if(SCp->cmnd[0] == TEST_UNIT_READY) { 1921 /* FIXME: This is because of a problem in the new 1922 * error handler. When it is in error recovery, it 1923 * will send a TUR to a device it thinks may still be 1924 * showing a problem. If the TUR isn't responded to, 1925 * it will abort it and mark the device off line. 1926 * Unfortunately, it does no other error recovery, so 1927 * this would leave us with an outstanding command 1928 * occupying a slot. Rather than allow this to 1929 * happen, we issue a bus reset to force all 1930 * outstanding commands to terminate here. */ 1931 NCR_700_internal_bus_reset(SCp->device->host); 1932 /* still drop through and return failed */ 1933 } 1934 return FAILED; 1935 1936 } 1937 1938 STATIC int 1939 NCR_700_bus_reset(struct scsi_cmnd * SCp) 1940 { 1941 DECLARE_COMPLETION_ONSTACK(complete); 1942 struct NCR_700_Host_Parameters *hostdata = 1943 (struct NCR_700_Host_Parameters *)SCp->device->host->hostdata[0]; 1944 1945 scmd_printk(KERN_INFO, SCp, 1946 "New error handler wants BUS reset, cmd %p\n\t", SCp); 1947 scsi_print_command(SCp); 1948 1949 /* In theory, eh_complete should always be null because the 1950 * eh is single threaded, but just in case we're handling a 1951 * reset via sg or something */ 1952 spin_lock_irq(SCp->device->host->host_lock); 1953 while (hostdata->eh_complete != NULL) { 1954 spin_unlock_irq(SCp->device->host->host_lock); 1955 msleep_interruptible(100); 1956 spin_lock_irq(SCp->device->host->host_lock); 1957 } 1958 1959 hostdata->eh_complete = &complete; 1960 NCR_700_internal_bus_reset(SCp->device->host); 1961 1962 spin_unlock_irq(SCp->device->host->host_lock); 1963 wait_for_completion(&complete); 1964 spin_lock_irq(SCp->device->host->host_lock); 1965 1966 hostdata->eh_complete = NULL; 1967 /* Revalidate the transport parameters of the failing device */ 1968 if(hostdata->fast) 1969 spi_schedule_dv_device(SCp->device); 1970 1971 spin_unlock_irq(SCp->device->host->host_lock); 1972 return SUCCESS; 1973 } 1974 1975 STATIC int 1976 NCR_700_host_reset(struct scsi_cmnd * SCp) 1977 { 1978 scmd_printk(KERN_INFO, SCp, "New error handler wants HOST reset\n\t"); 1979 scsi_print_command(SCp); 1980 1981 spin_lock_irq(SCp->device->host->host_lock); 1982 1983 NCR_700_internal_bus_reset(SCp->device->host); 1984 NCR_700_chip_reset(SCp->device->host); 1985 1986 spin_unlock_irq(SCp->device->host->host_lock); 1987 1988 return SUCCESS; 1989 } 1990 1991 STATIC void 1992 NCR_700_set_period(struct scsi_target *STp, int period) 1993 { 1994 struct Scsi_Host *SHp = dev_to_shost(STp->dev.parent); 1995 struct NCR_700_Host_Parameters *hostdata = 1996 (struct NCR_700_Host_Parameters *)SHp->hostdata[0]; 1997 1998 if(!hostdata->fast) 1999 return; 2000 2001 if(period < hostdata->min_period) 2002 period = hostdata->min_period; 2003 2004 spi_period(STp) = period; 2005 spi_flags(STp) &= ~(NCR_700_DEV_NEGOTIATED_SYNC | 2006 NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); 2007 spi_flags(STp) |= NCR_700_DEV_PRINT_SYNC_NEGOTIATION; 2008 } 2009 2010 STATIC void 2011 NCR_700_set_offset(struct scsi_target *STp, int offset) 2012 { 2013 struct Scsi_Host *SHp = dev_to_shost(STp->dev.parent); 2014 struct NCR_700_Host_Parameters *hostdata = 2015 (struct NCR_700_Host_Parameters *)SHp->hostdata[0]; 2016 int max_offset = hostdata->chip710 2017 ? NCR_710_MAX_OFFSET : NCR_700_MAX_OFFSET; 2018 2019 if(!hostdata->fast) 2020 return; 2021 2022 if(offset > max_offset) 2023 offset = max_offset; 2024 2025 /* if we're currently async, make sure the period is reasonable */ 2026 if(spi_offset(STp) == 0 && (spi_period(STp) < hostdata->min_period || 2027 spi_period(STp) > 0xff)) 2028 spi_period(STp) = hostdata->min_period; 2029 2030 spi_offset(STp) = offset; 2031 spi_flags(STp) &= ~(NCR_700_DEV_NEGOTIATED_SYNC | 2032 NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); 2033 spi_flags(STp) |= NCR_700_DEV_PRINT_SYNC_NEGOTIATION; 2034 } 2035 2036 STATIC int 2037 NCR_700_slave_alloc(struct scsi_device *SDp) 2038 { 2039 SDp->hostdata = kzalloc(sizeof(struct NCR_700_Device_Parameters), 2040 GFP_KERNEL); 2041 2042 if (!SDp->hostdata) 2043 return -ENOMEM; 2044 2045 return 0; 2046 } 2047 2048 STATIC int 2049 NCR_700_slave_configure(struct scsi_device *SDp) 2050 { 2051 struct NCR_700_Host_Parameters *hostdata = 2052 (struct NCR_700_Host_Parameters *)SDp->host->hostdata[0]; 2053 2054 /* to do here: allocate memory; build a queue_full list */ 2055 if(SDp->tagged_supported) { 2056 scsi_change_queue_depth(SDp, NCR_700_DEFAULT_TAGS); 2057 NCR_700_set_tag_neg_state(SDp, NCR_700_START_TAG_NEGOTIATION); 2058 } 2059 2060 if(hostdata->fast) { 2061 /* Find the correct offset and period via domain validation */ 2062 if (!spi_initial_dv(SDp->sdev_target)) 2063 spi_dv_device(SDp); 2064 } else { 2065 spi_offset(SDp->sdev_target) = 0; 2066 spi_period(SDp->sdev_target) = 0; 2067 } 2068 return 0; 2069 } 2070 2071 STATIC void 2072 NCR_700_slave_destroy(struct scsi_device *SDp) 2073 { 2074 kfree(SDp->hostdata); 2075 SDp->hostdata = NULL; 2076 } 2077 2078 static int 2079 NCR_700_change_queue_depth(struct scsi_device *SDp, int depth) 2080 { 2081 if (depth > NCR_700_MAX_TAGS) 2082 depth = NCR_700_MAX_TAGS; 2083 return scsi_change_queue_depth(SDp, depth); 2084 } 2085 2086 static ssize_t 2087 NCR_700_show_active_tags(struct device *dev, struct device_attribute *attr, char *buf) 2088 { 2089 struct scsi_device *SDp = to_scsi_device(dev); 2090 2091 return snprintf(buf, 20, "%d\n", NCR_700_get_depth(SDp)); 2092 } 2093 2094 static struct device_attribute NCR_700_active_tags_attr = { 2095 .attr = { 2096 .name = "active_tags", 2097 .mode = S_IRUGO, 2098 }, 2099 .show = NCR_700_show_active_tags, 2100 }; 2101 2102 STATIC struct device_attribute *NCR_700_dev_attrs[] = { 2103 &NCR_700_active_tags_attr, 2104 NULL, 2105 }; 2106 2107 EXPORT_SYMBOL(NCR_700_detect); 2108 EXPORT_SYMBOL(NCR_700_release); 2109 EXPORT_SYMBOL(NCR_700_intr); 2110 2111 static struct spi_function_template NCR_700_transport_functions = { 2112 .set_period = NCR_700_set_period, 2113 .show_period = 1, 2114 .set_offset = NCR_700_set_offset, 2115 .show_offset = 1, 2116 }; 2117 2118 static int __init NCR_700_init(void) 2119 { 2120 NCR_700_transport_template = spi_attach_transport(&NCR_700_transport_functions); 2121 if(!NCR_700_transport_template) 2122 return -ENODEV; 2123 return 0; 2124 } 2125 2126 static void __exit NCR_700_exit(void) 2127 { 2128 spi_release_transport(NCR_700_transport_template); 2129 } 2130 2131 module_init(NCR_700_init); 2132 module_exit(NCR_700_exit); 2133 2134