1 /* -*- mode: c; c-basic-offset: 8 -*- */ 2 3 /* NCR (or Symbios) 53c700 and 53c700-66 Driver 4 * 5 * Copyright (C) 2001 by James.Bottomley@HansenPartnership.com 6 **----------------------------------------------------------------------------- 7 ** 8 ** This program is free software; you can redistribute it and/or modify 9 ** it under the terms of the GNU General Public License as published by 10 ** the Free Software Foundation; either version 2 of the License, or 11 ** (at your option) any later version. 12 ** 13 ** This program is distributed in the hope that it will be useful, 14 ** but WITHOUT ANY WARRANTY; without even the implied warranty of 15 ** MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 16 ** GNU General Public License for more details. 17 ** 18 ** You should have received a copy of the GNU General Public License 19 ** along with this program; if not, write to the Free Software 20 ** Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. 21 ** 22 **----------------------------------------------------------------------------- 23 */ 24 25 /* Notes: 26 * 27 * This driver is designed exclusively for these chips (virtually the 28 * earliest of the scripts engine chips). They need their own drivers 29 * because they are missing so many of the scripts and snazzy register 30 * features of their elder brothers (the 710, 720 and 770). 31 * 32 * The 700 is the lowliest of the line, it can only do async SCSI. 33 * The 700-66 can at least do synchronous SCSI up to 10MHz. 34 * 35 * The 700 chip has no host bus interface logic of its own. However, 36 * it is usually mapped to a location with well defined register 37 * offsets. Therefore, if you can determine the base address and the 38 * irq your board incorporating this chip uses, you can probably use 39 * this driver to run it (although you'll probably have to write a 40 * minimal wrapper for the purpose---see the NCR_D700 driver for 41 * details about how to do this). 42 * 43 * 44 * TODO List: 45 * 46 * 1. Better statistics in the proc fs 47 * 48 * 2. Implement message queue (queues SCSI messages like commands) and make 49 * the abort and device reset functions use them. 50 * */ 51 52 /* CHANGELOG 53 * 54 * Version 2.8 55 * 56 * Fixed bad bug affecting tag starvation processing (previously the 57 * driver would hang the system if too many tags starved. Also fixed 58 * bad bug having to do with 10 byte command processing and REQUEST 59 * SENSE (the command would loop forever getting a transfer length 60 * mismatch in the CMD phase). 61 * 62 * Version 2.7 63 * 64 * Fixed scripts problem which caused certain devices (notably CDRWs) 65 * to hang on initial INQUIRY. Updated NCR_700_readl/writel to use 66 * __raw_readl/writel for parisc compatibility (Thomas 67 * Bogendoerfer). Added missing SCp->request_bufflen initialisation 68 * for sense requests (Ryan Bradetich). 69 * 70 * Version 2.6 71 * 72 * Following test of the 64 bit parisc kernel by Richard Hirst, 73 * several problems have now been corrected. Also adds support for 74 * consistent memory allocation. 75 * 76 * Version 2.5 77 * 78 * More Compatibility changes for 710 (now actually works). Enhanced 79 * support for odd clock speeds which constrain SDTR negotiations. 80 * correct cacheline separation for scsi messages and status for 81 * incoherent architectures. Use of the pci mapping functions on 82 * buffers to begin support for 64 bit drivers. 83 * 84 * Version 2.4 85 * 86 * Added support for the 53c710 chip (in 53c700 emulation mode only---no 87 * special 53c710 instructions or registers are used). 88 * 89 * Version 2.3 90 * 91 * More endianness/cache coherency changes. 92 * 93 * Better bad device handling (handles devices lying about tag 94 * queueing support and devices which fail to provide sense data on 95 * contingent allegiance conditions) 96 * 97 * Many thanks to Richard Hirst <rhirst@linuxcare.com> for patiently 98 * debugging this driver on the parisc architecture and suggesting 99 * many improvements and bug fixes. 100 * 101 * Thanks also go to Linuxcare Inc. for providing several PARISC 102 * machines for me to debug the driver on. 103 * 104 * Version 2.2 105 * 106 * Made the driver mem or io mapped; added endian invariance; added 107 * dma cache flushing operations for architectures which need it; 108 * added support for more varied clocking speeds. 109 * 110 * Version 2.1 111 * 112 * Initial modularisation from the D700. See NCR_D700.c for the rest of 113 * the changelog. 114 * */ 115 #define NCR_700_VERSION "2.8" 116 117 #include <linux/config.h> 118 #include <linux/kernel.h> 119 #include <linux/types.h> 120 #include <linux/string.h> 121 #include <linux/ioport.h> 122 #include <linux/delay.h> 123 #include <linux/spinlock.h> 124 #include <linux/completion.h> 125 #include <linux/sched.h> 126 #include <linux/init.h> 127 #include <linux/proc_fs.h> 128 #include <linux/blkdev.h> 129 #include <linux/module.h> 130 #include <linux/interrupt.h> 131 #include <linux/device.h> 132 #include <asm/dma.h> 133 #include <asm/system.h> 134 #include <asm/io.h> 135 #include <asm/pgtable.h> 136 #include <asm/byteorder.h> 137 138 #include <scsi/scsi.h> 139 #include <scsi/scsi_cmnd.h> 140 #include <scsi/scsi_dbg.h> 141 #include <scsi/scsi_eh.h> 142 #include <scsi/scsi_host.h> 143 #include <scsi/scsi_tcq.h> 144 #include <scsi/scsi_transport.h> 145 #include <scsi/scsi_transport_spi.h> 146 147 #include "53c700.h" 148 149 /* NOTE: For 64 bit drivers there are points in the code where we use 150 * a non dereferenceable pointer to point to a structure in dma-able 151 * memory (which is 32 bits) so that we can use all of the structure 152 * operations but take the address at the end. This macro allows us 153 * to truncate the 64 bit pointer down to 32 bits without the compiler 154 * complaining */ 155 #define to32bit(x) ((__u32)((unsigned long)(x))) 156 157 #ifdef NCR_700_DEBUG 158 #define STATIC 159 #else 160 #define STATIC static 161 #endif 162 163 MODULE_AUTHOR("James Bottomley"); 164 MODULE_DESCRIPTION("53c700 and 53c700-66 Driver"); 165 MODULE_LICENSE("GPL"); 166 167 /* This is the script */ 168 #include "53c700_d.h" 169 170 171 STATIC int NCR_700_queuecommand(struct scsi_cmnd *, void (*done)(struct scsi_cmnd *)); 172 STATIC int NCR_700_abort(struct scsi_cmnd * SCpnt); 173 STATIC int NCR_700_bus_reset(struct scsi_cmnd * SCpnt); 174 STATIC int NCR_700_host_reset(struct scsi_cmnd * SCpnt); 175 STATIC void NCR_700_chip_setup(struct Scsi_Host *host); 176 STATIC void NCR_700_chip_reset(struct Scsi_Host *host); 177 STATIC int NCR_700_slave_configure(struct scsi_device *SDpnt); 178 STATIC void NCR_700_slave_destroy(struct scsi_device *SDpnt); 179 static int NCR_700_change_queue_depth(struct scsi_device *SDpnt, int depth); 180 static int NCR_700_change_queue_type(struct scsi_device *SDpnt, int depth); 181 182 STATIC struct device_attribute *NCR_700_dev_attrs[]; 183 184 STATIC struct scsi_transport_template *NCR_700_transport_template = NULL; 185 186 static char *NCR_700_phase[] = { 187 "", 188 "after selection", 189 "before command phase", 190 "after command phase", 191 "after status phase", 192 "after data in phase", 193 "after data out phase", 194 "during data phase", 195 }; 196 197 static char *NCR_700_condition[] = { 198 "", 199 "NOT MSG_OUT", 200 "UNEXPECTED PHASE", 201 "NOT MSG_IN", 202 "UNEXPECTED MSG", 203 "MSG_IN", 204 "SDTR_MSG RECEIVED", 205 "REJECT_MSG RECEIVED", 206 "DISCONNECT_MSG RECEIVED", 207 "MSG_OUT", 208 "DATA_IN", 209 210 }; 211 212 static char *NCR_700_fatal_messages[] = { 213 "unexpected message after reselection", 214 "still MSG_OUT after message injection", 215 "not MSG_IN after selection", 216 "Illegal message length received", 217 }; 218 219 static char *NCR_700_SBCL_bits[] = { 220 "IO ", 221 "CD ", 222 "MSG ", 223 "ATN ", 224 "SEL ", 225 "BSY ", 226 "ACK ", 227 "REQ ", 228 }; 229 230 static char *NCR_700_SBCL_to_phase[] = { 231 "DATA_OUT", 232 "DATA_IN", 233 "CMD_OUT", 234 "STATE", 235 "ILLEGAL PHASE", 236 "ILLEGAL PHASE", 237 "MSG OUT", 238 "MSG IN", 239 }; 240 241 static __u8 NCR_700_SDTR_msg[] = { 242 0x01, /* Extended message */ 243 0x03, /* Extended message Length */ 244 0x01, /* SDTR Extended message */ 245 NCR_700_MIN_PERIOD, 246 NCR_700_MAX_OFFSET 247 }; 248 249 /* This translates the SDTR message offset and period to a value 250 * which can be loaded into the SXFER_REG. 251 * 252 * NOTE: According to SCSI-2, the true transfer period (in ns) is 253 * actually four times this period value */ 254 static inline __u8 255 NCR_700_offset_period_to_sxfer(struct NCR_700_Host_Parameters *hostdata, 256 __u8 offset, __u8 period) 257 { 258 int XFERP; 259 260 __u8 min_xferp = (hostdata->chip710 261 ? NCR_710_MIN_XFERP : NCR_700_MIN_XFERP); 262 __u8 max_offset = (hostdata->chip710 263 ? NCR_710_MAX_OFFSET : NCR_700_MAX_OFFSET); 264 265 if(offset == 0) 266 return 0; 267 268 if(period < hostdata->min_period) { 269 printk(KERN_WARNING "53c700: Period %dns is less than this chip's minimum, setting to %d\n", period*4, NCR_700_SDTR_msg[3]*4); 270 period = hostdata->min_period; 271 } 272 XFERP = (period*4 * hostdata->sync_clock)/1000 - 4; 273 if(offset > max_offset) { 274 printk(KERN_WARNING "53c700: Offset %d exceeds chip maximum, setting to %d\n", 275 offset, max_offset); 276 offset = max_offset; 277 } 278 if(XFERP < min_xferp) { 279 printk(KERN_WARNING "53c700: XFERP %d is less than minium, setting to %d\n", 280 XFERP, min_xferp); 281 XFERP = min_xferp; 282 } 283 return (offset & 0x0f) | (XFERP & 0x07)<<4; 284 } 285 286 static inline __u8 287 NCR_700_get_SXFER(struct scsi_device *SDp) 288 { 289 struct NCR_700_Host_Parameters *hostdata = 290 (struct NCR_700_Host_Parameters *)SDp->host->hostdata[0]; 291 292 return NCR_700_offset_period_to_sxfer(hostdata, 293 spi_offset(SDp->sdev_target), 294 spi_period(SDp->sdev_target)); 295 } 296 297 struct Scsi_Host * 298 NCR_700_detect(struct scsi_host_template *tpnt, 299 struct NCR_700_Host_Parameters *hostdata, struct device *dev) 300 { 301 dma_addr_t pScript, pSlots; 302 __u8 *memory; 303 __u32 *script; 304 struct Scsi_Host *host; 305 static int banner = 0; 306 int j; 307 308 if(tpnt->sdev_attrs == NULL) 309 tpnt->sdev_attrs = NCR_700_dev_attrs; 310 311 memory = dma_alloc_noncoherent(hostdata->dev, TOTAL_MEM_SIZE, 312 &pScript, GFP_KERNEL); 313 if(memory == NULL) { 314 printk(KERN_ERR "53c700: Failed to allocate memory for driver, detatching\n"); 315 return NULL; 316 } 317 318 script = (__u32 *)memory; 319 hostdata->msgin = memory + MSGIN_OFFSET; 320 hostdata->msgout = memory + MSGOUT_OFFSET; 321 hostdata->status = memory + STATUS_OFFSET; 322 /* all of these offsets are L1_CACHE_BYTES separated. It is fatal 323 * if this isn't sufficient separation to avoid dma flushing issues */ 324 BUG_ON(!dma_is_consistent(pScript) && L1_CACHE_BYTES < dma_get_cache_alignment()); 325 hostdata->slots = (struct NCR_700_command_slot *)(memory + SLOTS_OFFSET); 326 hostdata->dev = dev; 327 328 pSlots = pScript + SLOTS_OFFSET; 329 330 /* Fill in the missing routines from the host template */ 331 tpnt->queuecommand = NCR_700_queuecommand; 332 tpnt->eh_abort_handler = NCR_700_abort; 333 tpnt->eh_bus_reset_handler = NCR_700_bus_reset; 334 tpnt->eh_host_reset_handler = NCR_700_host_reset; 335 tpnt->can_queue = NCR_700_COMMAND_SLOTS_PER_HOST; 336 tpnt->sg_tablesize = NCR_700_SG_SEGMENTS; 337 tpnt->cmd_per_lun = NCR_700_CMD_PER_LUN; 338 tpnt->use_clustering = ENABLE_CLUSTERING; 339 tpnt->slave_configure = NCR_700_slave_configure; 340 tpnt->slave_destroy = NCR_700_slave_destroy; 341 tpnt->change_queue_depth = NCR_700_change_queue_depth; 342 tpnt->change_queue_type = NCR_700_change_queue_type; 343 344 if(tpnt->name == NULL) 345 tpnt->name = "53c700"; 346 if(tpnt->proc_name == NULL) 347 tpnt->proc_name = "53c700"; 348 349 350 host = scsi_host_alloc(tpnt, 4); 351 if (!host) 352 return NULL; 353 memset(hostdata->slots, 0, sizeof(struct NCR_700_command_slot) 354 * NCR_700_COMMAND_SLOTS_PER_HOST); 355 for(j = 0; j < NCR_700_COMMAND_SLOTS_PER_HOST; j++) { 356 dma_addr_t offset = (dma_addr_t)((unsigned long)&hostdata->slots[j].SG[0] 357 - (unsigned long)&hostdata->slots[0].SG[0]); 358 hostdata->slots[j].pSG = (struct NCR_700_SG_List *)((unsigned long)(pSlots + offset)); 359 if(j == 0) 360 hostdata->free_list = &hostdata->slots[j]; 361 else 362 hostdata->slots[j-1].ITL_forw = &hostdata->slots[j]; 363 hostdata->slots[j].state = NCR_700_SLOT_FREE; 364 } 365 366 for(j = 0; j < sizeof(SCRIPT)/sizeof(SCRIPT[0]); j++) { 367 script[j] = bS_to_host(SCRIPT[j]); 368 } 369 370 /* adjust all labels to be bus physical */ 371 for(j = 0; j < PATCHES; j++) { 372 script[LABELPATCHES[j]] = bS_to_host(pScript + SCRIPT[LABELPATCHES[j]]); 373 } 374 /* now patch up fixed addresses. */ 375 script_patch_32(script, MessageLocation, 376 pScript + MSGOUT_OFFSET); 377 script_patch_32(script, StatusAddress, 378 pScript + STATUS_OFFSET); 379 script_patch_32(script, ReceiveMsgAddress, 380 pScript + MSGIN_OFFSET); 381 382 hostdata->script = script; 383 hostdata->pScript = pScript; 384 dma_sync_single_for_device(hostdata->dev, pScript, sizeof(SCRIPT), DMA_TO_DEVICE); 385 hostdata->state = NCR_700_HOST_FREE; 386 hostdata->cmd = NULL; 387 host->max_id = 7; 388 host->max_lun = NCR_700_MAX_LUNS; 389 BUG_ON(NCR_700_transport_template == NULL); 390 host->transportt = NCR_700_transport_template; 391 host->unique_id = (unsigned long)hostdata->base; 392 hostdata->eh_complete = NULL; 393 host->hostdata[0] = (unsigned long)hostdata; 394 /* kick the chip */ 395 NCR_700_writeb(0xff, host, CTEST9_REG); 396 if(hostdata->chip710) 397 hostdata->rev = (NCR_700_readb(host, CTEST8_REG)>>4) & 0x0f; 398 else 399 hostdata->rev = (NCR_700_readb(host, CTEST7_REG)>>4) & 0x0f; 400 hostdata->fast = (NCR_700_readb(host, CTEST9_REG) == 0); 401 if(banner == 0) { 402 printk(KERN_NOTICE "53c700: Version " NCR_700_VERSION " By James.Bottomley@HansenPartnership.com\n"); 403 banner = 1; 404 } 405 printk(KERN_NOTICE "scsi%d: %s rev %d %s\n", host->host_no, 406 hostdata->chip710 ? "53c710" : 407 (hostdata->fast ? "53c700-66" : "53c700"), 408 hostdata->rev, hostdata->differential ? 409 "(Differential)" : ""); 410 /* reset the chip */ 411 NCR_700_chip_reset(host); 412 413 if (scsi_add_host(host, dev)) { 414 dev_printk(KERN_ERR, dev, "53c700: scsi_add_host failed\n"); 415 scsi_host_put(host); 416 return NULL; 417 } 418 419 spi_signalling(host) = hostdata->differential ? SPI_SIGNAL_HVD : 420 SPI_SIGNAL_SE; 421 422 return host; 423 } 424 425 int 426 NCR_700_release(struct Scsi_Host *host) 427 { 428 struct NCR_700_Host_Parameters *hostdata = 429 (struct NCR_700_Host_Parameters *)host->hostdata[0]; 430 431 dma_free_noncoherent(hostdata->dev, TOTAL_MEM_SIZE, 432 hostdata->script, hostdata->pScript); 433 return 1; 434 } 435 436 static inline __u8 437 NCR_700_identify(int can_disconnect, __u8 lun) 438 { 439 return IDENTIFY_BASE | 440 ((can_disconnect) ? 0x40 : 0) | 441 (lun & NCR_700_LUN_MASK); 442 } 443 444 /* 445 * Function : static int data_residual (Scsi_Host *host) 446 * 447 * Purpose : return residual data count of what's in the chip. If you 448 * really want to know what this function is doing, it's almost a 449 * direct transcription of the algorithm described in the 53c710 450 * guide, except that the DBC and DFIFO registers are only 6 bits 451 * wide on a 53c700. 452 * 453 * Inputs : host - SCSI host */ 454 static inline int 455 NCR_700_data_residual (struct Scsi_Host *host) { 456 struct NCR_700_Host_Parameters *hostdata = 457 (struct NCR_700_Host_Parameters *)host->hostdata[0]; 458 int count, synchronous = 0; 459 unsigned int ddir; 460 461 if(hostdata->chip710) { 462 count = ((NCR_700_readb(host, DFIFO_REG) & 0x7f) - 463 (NCR_700_readl(host, DBC_REG) & 0x7f)) & 0x7f; 464 } else { 465 count = ((NCR_700_readb(host, DFIFO_REG) & 0x3f) - 466 (NCR_700_readl(host, DBC_REG) & 0x3f)) & 0x3f; 467 } 468 469 if(hostdata->fast) 470 synchronous = NCR_700_readb(host, SXFER_REG) & 0x0f; 471 472 /* get the data direction */ 473 ddir = NCR_700_readb(host, CTEST0_REG) & 0x01; 474 475 if (ddir) { 476 /* Receive */ 477 if (synchronous) 478 count += (NCR_700_readb(host, SSTAT2_REG) & 0xf0) >> 4; 479 else 480 if (NCR_700_readb(host, SSTAT1_REG) & SIDL_REG_FULL) 481 ++count; 482 } else { 483 /* Send */ 484 __u8 sstat = NCR_700_readb(host, SSTAT1_REG); 485 if (sstat & SODL_REG_FULL) 486 ++count; 487 if (synchronous && (sstat & SODR_REG_FULL)) 488 ++count; 489 } 490 #ifdef NCR_700_DEBUG 491 if(count) 492 printk("RESIDUAL IS %d (ddir %d)\n", count, ddir); 493 #endif 494 return count; 495 } 496 497 /* print out the SCSI wires and corresponding phase from the SBCL register 498 * in the chip */ 499 static inline char * 500 sbcl_to_string(__u8 sbcl) 501 { 502 int i; 503 static char ret[256]; 504 505 ret[0]='\0'; 506 for(i=0; i<8; i++) { 507 if((1<<i) & sbcl) 508 strcat(ret, NCR_700_SBCL_bits[i]); 509 } 510 strcat(ret, NCR_700_SBCL_to_phase[sbcl & 0x07]); 511 return ret; 512 } 513 514 static inline __u8 515 bitmap_to_number(__u8 bitmap) 516 { 517 __u8 i; 518 519 for(i=0; i<8 && !(bitmap &(1<<i)); i++) 520 ; 521 return i; 522 } 523 524 /* Pull a slot off the free list */ 525 STATIC struct NCR_700_command_slot * 526 find_empty_slot(struct NCR_700_Host_Parameters *hostdata) 527 { 528 struct NCR_700_command_slot *slot = hostdata->free_list; 529 530 if(slot == NULL) { 531 /* sanity check */ 532 if(hostdata->command_slot_count != NCR_700_COMMAND_SLOTS_PER_HOST) 533 printk(KERN_ERR "SLOTS FULL, but count is %d, should be %d\n", hostdata->command_slot_count, NCR_700_COMMAND_SLOTS_PER_HOST); 534 return NULL; 535 } 536 537 if(slot->state != NCR_700_SLOT_FREE) 538 /* should panic! */ 539 printk(KERN_ERR "BUSY SLOT ON FREE LIST!!!\n"); 540 541 542 hostdata->free_list = slot->ITL_forw; 543 slot->ITL_forw = NULL; 544 545 546 /* NOTE: set the state to busy here, not queued, since this 547 * indicates the slot is in use and cannot be run by the IRQ 548 * finish routine. If we cannot queue the command when it 549 * is properly build, we then change to NCR_700_SLOT_QUEUED */ 550 slot->state = NCR_700_SLOT_BUSY; 551 hostdata->command_slot_count++; 552 553 return slot; 554 } 555 556 STATIC void 557 free_slot(struct NCR_700_command_slot *slot, 558 struct NCR_700_Host_Parameters *hostdata) 559 { 560 if((slot->state & NCR_700_SLOT_MASK) != NCR_700_SLOT_MAGIC) { 561 printk(KERN_ERR "53c700: SLOT %p is not MAGIC!!!\n", slot); 562 } 563 if(slot->state == NCR_700_SLOT_FREE) { 564 printk(KERN_ERR "53c700: SLOT %p is FREE!!!\n", slot); 565 } 566 567 slot->resume_offset = 0; 568 slot->cmnd = NULL; 569 slot->state = NCR_700_SLOT_FREE; 570 slot->ITL_forw = hostdata->free_list; 571 hostdata->free_list = slot; 572 hostdata->command_slot_count--; 573 } 574 575 576 /* This routine really does very little. The command is indexed on 577 the ITL and (if tagged) the ITLQ lists in _queuecommand */ 578 STATIC void 579 save_for_reselection(struct NCR_700_Host_Parameters *hostdata, 580 struct scsi_cmnd *SCp, __u32 dsp) 581 { 582 /* Its just possible that this gets executed twice */ 583 if(SCp != NULL) { 584 struct NCR_700_command_slot *slot = 585 (struct NCR_700_command_slot *)SCp->host_scribble; 586 587 slot->resume_offset = dsp; 588 } 589 hostdata->state = NCR_700_HOST_FREE; 590 hostdata->cmd = NULL; 591 } 592 593 STATIC inline void 594 NCR_700_unmap(struct NCR_700_Host_Parameters *hostdata, struct scsi_cmnd *SCp, 595 struct NCR_700_command_slot *slot) 596 { 597 if(SCp->sc_data_direction != DMA_NONE && 598 SCp->sc_data_direction != DMA_BIDIRECTIONAL) { 599 if(SCp->use_sg) { 600 dma_unmap_sg(hostdata->dev, SCp->buffer, 601 SCp->use_sg, SCp->sc_data_direction); 602 } else { 603 dma_unmap_single(hostdata->dev, slot->dma_handle, 604 SCp->request_bufflen, 605 SCp->sc_data_direction); 606 } 607 } 608 } 609 610 STATIC inline void 611 NCR_700_scsi_done(struct NCR_700_Host_Parameters *hostdata, 612 struct scsi_cmnd *SCp, int result) 613 { 614 hostdata->state = NCR_700_HOST_FREE; 615 hostdata->cmd = NULL; 616 617 if(SCp != NULL) { 618 struct NCR_700_command_slot *slot = 619 (struct NCR_700_command_slot *)SCp->host_scribble; 620 621 NCR_700_unmap(hostdata, SCp, slot); 622 dma_unmap_single(hostdata->dev, slot->pCmd, 623 sizeof(SCp->cmnd), DMA_TO_DEVICE); 624 if(SCp->cmnd[0] == REQUEST_SENSE && SCp->cmnd[6] == NCR_700_INTERNAL_SENSE_MAGIC) { 625 #ifdef NCR_700_DEBUG 626 printk(" ORIGINAL CMD %p RETURNED %d, new return is %d sense is\n", 627 SCp, SCp->cmnd[7], result); 628 scsi_print_sense("53c700", SCp); 629 630 #endif 631 /* restore the old result if the request sense was 632 * successful */ 633 if(result == 0) 634 result = SCp->cmnd[7]; 635 /* now restore the original command */ 636 memcpy((void *) SCp->cmnd, (void *) SCp->data_cmnd, 637 sizeof(SCp->data_cmnd)); 638 SCp->request_buffer = SCp->buffer; 639 SCp->request_bufflen = SCp->bufflen; 640 SCp->use_sg = SCp->old_use_sg; 641 SCp->cmd_len = SCp->old_cmd_len; 642 SCp->sc_data_direction = SCp->sc_old_data_direction; 643 SCp->underflow = SCp->old_underflow; 644 645 } 646 free_slot(slot, hostdata); 647 #ifdef NCR_700_DEBUG 648 if(NCR_700_get_depth(SCp->device) == 0 || 649 NCR_700_get_depth(SCp->device) > SCp->device->queue_depth) 650 printk(KERN_ERR "Invalid depth in NCR_700_scsi_done(): %d\n", 651 NCR_700_get_depth(SCp->device)); 652 #endif /* NCR_700_DEBUG */ 653 NCR_700_set_depth(SCp->device, NCR_700_get_depth(SCp->device) - 1); 654 655 SCp->host_scribble = NULL; 656 SCp->result = result; 657 SCp->scsi_done(SCp); 658 } else { 659 printk(KERN_ERR "53c700: SCSI DONE HAS NULL SCp\n"); 660 } 661 } 662 663 664 STATIC void 665 NCR_700_internal_bus_reset(struct Scsi_Host *host) 666 { 667 /* Bus reset */ 668 NCR_700_writeb(ASSERT_RST, host, SCNTL1_REG); 669 udelay(50); 670 NCR_700_writeb(0, host, SCNTL1_REG); 671 672 } 673 674 STATIC void 675 NCR_700_chip_setup(struct Scsi_Host *host) 676 { 677 struct NCR_700_Host_Parameters *hostdata = 678 (struct NCR_700_Host_Parameters *)host->hostdata[0]; 679 __u32 dcntl_extra = 0; 680 __u8 min_period; 681 __u8 min_xferp = (hostdata->chip710 ? NCR_710_MIN_XFERP : NCR_700_MIN_XFERP); 682 683 if(hostdata->chip710) { 684 __u8 burst_disable = hostdata->burst_disable 685 ? BURST_DISABLE : 0; 686 dcntl_extra = COMPAT_700_MODE; 687 688 NCR_700_writeb(dcntl_extra, host, DCNTL_REG); 689 NCR_700_writeb(BURST_LENGTH_8 | hostdata->dmode_extra, 690 host, DMODE_710_REG); 691 NCR_700_writeb(burst_disable | (hostdata->differential ? 692 DIFF : 0), host, CTEST7_REG); 693 NCR_700_writeb(BTB_TIMER_DISABLE, host, CTEST0_REG); 694 NCR_700_writeb(FULL_ARBITRATION | ENABLE_PARITY | PARITY 695 | AUTO_ATN, host, SCNTL0_REG); 696 } else { 697 NCR_700_writeb(BURST_LENGTH_8 | hostdata->dmode_extra, 698 host, DMODE_700_REG); 699 NCR_700_writeb(hostdata->differential ? 700 DIFF : 0, host, CTEST7_REG); 701 if(hostdata->fast) { 702 /* this is for 700-66, does nothing on 700 */ 703 NCR_700_writeb(LAST_DIS_ENBL | ENABLE_ACTIVE_NEGATION 704 | GENERATE_RECEIVE_PARITY, host, 705 CTEST8_REG); 706 } else { 707 NCR_700_writeb(FULL_ARBITRATION | ENABLE_PARITY 708 | PARITY | AUTO_ATN, host, SCNTL0_REG); 709 } 710 } 711 712 NCR_700_writeb(1 << host->this_id, host, SCID_REG); 713 NCR_700_writeb(0, host, SBCL_REG); 714 NCR_700_writeb(ASYNC_OPERATION, host, SXFER_REG); 715 716 NCR_700_writeb(PHASE_MM_INT | SEL_TIMEOUT_INT | GROSS_ERR_INT | UX_DISC_INT 717 | RST_INT | PAR_ERR_INT | SELECT_INT, host, SIEN_REG); 718 719 NCR_700_writeb(ABORT_INT | INT_INST_INT | ILGL_INST_INT, host, DIEN_REG); 720 NCR_700_writeb(ENABLE_SELECT, host, SCNTL1_REG); 721 if(hostdata->clock > 75) { 722 printk(KERN_ERR "53c700: Clock speed %dMHz is too high: 75Mhz is the maximum this chip can be driven at\n", hostdata->clock); 723 /* do the best we can, but the async clock will be out 724 * of spec: sync divider 2, async divider 3 */ 725 DEBUG(("53c700: sync 2 async 3\n")); 726 NCR_700_writeb(SYNC_DIV_2_0, host, SBCL_REG); 727 NCR_700_writeb(ASYNC_DIV_3_0 | dcntl_extra, host, DCNTL_REG); 728 hostdata->sync_clock = hostdata->clock/2; 729 } else if(hostdata->clock > 50 && hostdata->clock <= 75) { 730 /* sync divider 1.5, async divider 3 */ 731 DEBUG(("53c700: sync 1.5 async 3\n")); 732 NCR_700_writeb(SYNC_DIV_1_5, host, SBCL_REG); 733 NCR_700_writeb(ASYNC_DIV_3_0 | dcntl_extra, host, DCNTL_REG); 734 hostdata->sync_clock = hostdata->clock*2; 735 hostdata->sync_clock /= 3; 736 737 } else if(hostdata->clock > 37 && hostdata->clock <= 50) { 738 /* sync divider 1, async divider 2 */ 739 DEBUG(("53c700: sync 1 async 2\n")); 740 NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG); 741 NCR_700_writeb(ASYNC_DIV_2_0 | dcntl_extra, host, DCNTL_REG); 742 hostdata->sync_clock = hostdata->clock; 743 } else if(hostdata->clock > 25 && hostdata->clock <=37) { 744 /* sync divider 1, async divider 1.5 */ 745 DEBUG(("53c700: sync 1 async 1.5\n")); 746 NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG); 747 NCR_700_writeb(ASYNC_DIV_1_5 | dcntl_extra, host, DCNTL_REG); 748 hostdata->sync_clock = hostdata->clock; 749 } else { 750 DEBUG(("53c700: sync 1 async 1\n")); 751 NCR_700_writeb(SYNC_DIV_1_0, host, SBCL_REG); 752 NCR_700_writeb(ASYNC_DIV_1_0 | dcntl_extra, host, DCNTL_REG); 753 /* sync divider 1, async divider 1 */ 754 hostdata->sync_clock = hostdata->clock; 755 } 756 /* Calculate the actual minimum period that can be supported 757 * by our synchronous clock speed. See the 710 manual for 758 * exact details of this calculation which is based on a 759 * setting of the SXFER register */ 760 min_period = 1000*(4+min_xferp)/(4*hostdata->sync_clock); 761 hostdata->min_period = NCR_700_MIN_PERIOD; 762 if(min_period > NCR_700_MIN_PERIOD) 763 hostdata->min_period = min_period; 764 } 765 766 STATIC void 767 NCR_700_chip_reset(struct Scsi_Host *host) 768 { 769 struct NCR_700_Host_Parameters *hostdata = 770 (struct NCR_700_Host_Parameters *)host->hostdata[0]; 771 if(hostdata->chip710) { 772 NCR_700_writeb(SOFTWARE_RESET_710, host, ISTAT_REG); 773 udelay(100); 774 775 NCR_700_writeb(0, host, ISTAT_REG); 776 } else { 777 NCR_700_writeb(SOFTWARE_RESET, host, DCNTL_REG); 778 udelay(100); 779 780 NCR_700_writeb(0, host, DCNTL_REG); 781 } 782 783 mdelay(1000); 784 785 NCR_700_chip_setup(host); 786 } 787 788 /* The heart of the message processing engine is that the instruction 789 * immediately after the INT is the normal case (and so must be CLEAR 790 * ACK). If we want to do something else, we call that routine in 791 * scripts and set temp to be the normal case + 8 (skipping the CLEAR 792 * ACK) so that the routine returns correctly to resume its activity 793 * */ 794 STATIC __u32 795 process_extended_message(struct Scsi_Host *host, 796 struct NCR_700_Host_Parameters *hostdata, 797 struct scsi_cmnd *SCp, __u32 dsp, __u32 dsps) 798 { 799 __u32 resume_offset = dsp, temp = dsp + 8; 800 __u8 pun = 0xff, lun = 0xff; 801 802 if(SCp != NULL) { 803 pun = SCp->device->id; 804 lun = SCp->device->lun; 805 } 806 807 switch(hostdata->msgin[2]) { 808 case A_SDTR_MSG: 809 if(SCp != NULL && NCR_700_is_flag_set(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION)) { 810 struct scsi_target *starget = SCp->device->sdev_target; 811 __u8 period = hostdata->msgin[3]; 812 __u8 offset = hostdata->msgin[4]; 813 814 if(offset == 0 || period == 0) { 815 offset = 0; 816 period = 0; 817 } 818 819 spi_offset(starget) = offset; 820 spi_period(starget) = period; 821 822 if(NCR_700_is_flag_set(SCp->device, NCR_700_DEV_PRINT_SYNC_NEGOTIATION)) { 823 spi_display_xfer_agreement(starget); 824 NCR_700_clear_flag(SCp->device, NCR_700_DEV_PRINT_SYNC_NEGOTIATION); 825 } 826 827 NCR_700_set_flag(SCp->device, NCR_700_DEV_NEGOTIATED_SYNC); 828 NCR_700_clear_flag(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); 829 830 NCR_700_writeb(NCR_700_get_SXFER(SCp->device), 831 host, SXFER_REG); 832 833 } else { 834 /* SDTR message out of the blue, reject it */ 835 shost_printk(KERN_WARNING, host, 836 "Unexpected SDTR msg\n"); 837 hostdata->msgout[0] = A_REJECT_MSG; 838 dma_cache_sync(hostdata->msgout, 1, DMA_TO_DEVICE); 839 script_patch_16(hostdata->script, MessageCount, 1); 840 /* SendMsgOut returns, so set up the return 841 * address */ 842 resume_offset = hostdata->pScript + Ent_SendMessageWithATN; 843 } 844 break; 845 846 case A_WDTR_MSG: 847 printk(KERN_INFO "scsi%d: (%d:%d), Unsolicited WDTR after CMD, Rejecting\n", 848 host->host_no, pun, lun); 849 hostdata->msgout[0] = A_REJECT_MSG; 850 dma_cache_sync(hostdata->msgout, 1, DMA_TO_DEVICE); 851 script_patch_16(hostdata->script, MessageCount, 1); 852 resume_offset = hostdata->pScript + Ent_SendMessageWithATN; 853 854 break; 855 856 default: 857 printk(KERN_INFO "scsi%d (%d:%d): Unexpected message %s: ", 858 host->host_no, pun, lun, 859 NCR_700_phase[(dsps & 0xf00) >> 8]); 860 spi_print_msg(hostdata->msgin); 861 printk("\n"); 862 /* just reject it */ 863 hostdata->msgout[0] = A_REJECT_MSG; 864 dma_cache_sync(hostdata->msgout, 1, DMA_TO_DEVICE); 865 script_patch_16(hostdata->script, MessageCount, 1); 866 /* SendMsgOut returns, so set up the return 867 * address */ 868 resume_offset = hostdata->pScript + Ent_SendMessageWithATN; 869 } 870 NCR_700_writel(temp, host, TEMP_REG); 871 return resume_offset; 872 } 873 874 STATIC __u32 875 process_message(struct Scsi_Host *host, struct NCR_700_Host_Parameters *hostdata, 876 struct scsi_cmnd *SCp, __u32 dsp, __u32 dsps) 877 { 878 /* work out where to return to */ 879 __u32 temp = dsp + 8, resume_offset = dsp; 880 __u8 pun = 0xff, lun = 0xff; 881 882 if(SCp != NULL) { 883 pun = SCp->device->id; 884 lun = SCp->device->lun; 885 } 886 887 #ifdef NCR_700_DEBUG 888 printk("scsi%d (%d:%d): message %s: ", host->host_no, pun, lun, 889 NCR_700_phase[(dsps & 0xf00) >> 8]); 890 spi_print_msg(hostdata->msgin); 891 printk("\n"); 892 #endif 893 894 switch(hostdata->msgin[0]) { 895 896 case A_EXTENDED_MSG: 897 resume_offset = process_extended_message(host, hostdata, SCp, 898 dsp, dsps); 899 break; 900 901 case A_REJECT_MSG: 902 if(SCp != NULL && NCR_700_is_flag_set(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION)) { 903 /* Rejected our sync negotiation attempt */ 904 spi_period(SCp->device->sdev_target) = 905 spi_offset(SCp->device->sdev_target) = 0; 906 NCR_700_set_flag(SCp->device, NCR_700_DEV_NEGOTIATED_SYNC); 907 NCR_700_clear_flag(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); 908 } else if(SCp != NULL && NCR_700_get_tag_neg_state(SCp->device) == NCR_700_DURING_TAG_NEGOTIATION) { 909 /* rejected our first simple tag message */ 910 scmd_printk(KERN_WARNING, SCp, 911 "Rejected first tag queue attempt, turning off tag queueing\n"); 912 /* we're done negotiating */ 913 NCR_700_set_tag_neg_state(SCp->device, NCR_700_FINISHED_TAG_NEGOTIATION); 914 hostdata->tag_negotiated &= ~(1<<scmd_id(SCp)); 915 SCp->device->tagged_supported = 0; 916 scsi_deactivate_tcq(SCp->device, host->cmd_per_lun); 917 } else { 918 shost_printk(KERN_WARNING, host, 919 "(%d:%d) Unexpected REJECT Message %s\n", 920 pun, lun, 921 NCR_700_phase[(dsps & 0xf00) >> 8]); 922 /* however, just ignore it */ 923 } 924 break; 925 926 case A_PARITY_ERROR_MSG: 927 printk(KERN_ERR "scsi%d (%d:%d) Parity Error!\n", host->host_no, 928 pun, lun); 929 NCR_700_internal_bus_reset(host); 930 break; 931 case A_SIMPLE_TAG_MSG: 932 printk(KERN_INFO "scsi%d (%d:%d) SIMPLE TAG %d %s\n", host->host_no, 933 pun, lun, hostdata->msgin[1], 934 NCR_700_phase[(dsps & 0xf00) >> 8]); 935 /* just ignore it */ 936 break; 937 default: 938 printk(KERN_INFO "scsi%d (%d:%d): Unexpected message %s: ", 939 host->host_no, pun, lun, 940 NCR_700_phase[(dsps & 0xf00) >> 8]); 941 942 spi_print_msg(hostdata->msgin); 943 printk("\n"); 944 /* just reject it */ 945 hostdata->msgout[0] = A_REJECT_MSG; 946 dma_cache_sync(hostdata->msgout, 1, DMA_TO_DEVICE); 947 script_patch_16(hostdata->script, MessageCount, 1); 948 /* SendMsgOut returns, so set up the return 949 * address */ 950 resume_offset = hostdata->pScript + Ent_SendMessageWithATN; 951 952 break; 953 } 954 NCR_700_writel(temp, host, TEMP_REG); 955 /* set us up to receive another message */ 956 dma_cache_sync(hostdata->msgin, MSG_ARRAY_SIZE, DMA_FROM_DEVICE); 957 return resume_offset; 958 } 959 960 STATIC __u32 961 process_script_interrupt(__u32 dsps, __u32 dsp, struct scsi_cmnd *SCp, 962 struct Scsi_Host *host, 963 struct NCR_700_Host_Parameters *hostdata) 964 { 965 __u32 resume_offset = 0; 966 __u8 pun = 0xff, lun=0xff; 967 968 if(SCp != NULL) { 969 pun = SCp->device->id; 970 lun = SCp->device->lun; 971 } 972 973 if(dsps == A_GOOD_STATUS_AFTER_STATUS) { 974 DEBUG((" COMMAND COMPLETE, status=%02x\n", 975 hostdata->status[0])); 976 /* OK, if TCQ still under negotiation, we now know it works */ 977 if (NCR_700_get_tag_neg_state(SCp->device) == NCR_700_DURING_TAG_NEGOTIATION) 978 NCR_700_set_tag_neg_state(SCp->device, 979 NCR_700_FINISHED_TAG_NEGOTIATION); 980 981 /* check for contingent allegiance contitions */ 982 if(status_byte(hostdata->status[0]) == CHECK_CONDITION || 983 status_byte(hostdata->status[0]) == COMMAND_TERMINATED) { 984 struct NCR_700_command_slot *slot = 985 (struct NCR_700_command_slot *)SCp->host_scribble; 986 if(SCp->cmnd[0] == REQUEST_SENSE) { 987 /* OOPS: bad device, returning another 988 * contingent allegiance condition */ 989 scmd_printk(KERN_ERR, SCp, 990 "broken device is looping in contingent allegiance: ignoring\n"); 991 NCR_700_scsi_done(hostdata, SCp, hostdata->status[0]); 992 } else { 993 #ifdef NCR_DEBUG 994 scsi_print_command(SCp); 995 printk(" cmd %p has status %d, requesting sense\n", 996 SCp, hostdata->status[0]); 997 #endif 998 /* we can destroy the command here 999 * because the contingent allegiance 1000 * condition will cause a retry which 1001 * will re-copy the command from the 1002 * saved data_cmnd. We also unmap any 1003 * data associated with the command 1004 * here */ 1005 NCR_700_unmap(hostdata, SCp, slot); 1006 1007 SCp->cmnd[0] = REQUEST_SENSE; 1008 SCp->cmnd[1] = (SCp->device->lun & 0x7) << 5; 1009 SCp->cmnd[2] = 0; 1010 SCp->cmnd[3] = 0; 1011 SCp->cmnd[4] = sizeof(SCp->sense_buffer); 1012 SCp->cmnd[5] = 0; 1013 SCp->cmd_len = 6; 1014 /* Here's a quiet hack: the 1015 * REQUEST_SENSE command is six bytes, 1016 * so store a flag indicating that 1017 * this was an internal sense request 1018 * and the original status at the end 1019 * of the command */ 1020 SCp->cmnd[6] = NCR_700_INTERNAL_SENSE_MAGIC; 1021 SCp->cmnd[7] = hostdata->status[0]; 1022 SCp->use_sg = 0; 1023 SCp->sc_data_direction = DMA_FROM_DEVICE; 1024 dma_sync_single_for_device(hostdata->dev, slot->pCmd, 1025 SCp->cmd_len, DMA_TO_DEVICE); 1026 SCp->request_bufflen = sizeof(SCp->sense_buffer); 1027 slot->dma_handle = dma_map_single(hostdata->dev, SCp->sense_buffer, sizeof(SCp->sense_buffer), DMA_FROM_DEVICE); 1028 slot->SG[0].ins = bS_to_host(SCRIPT_MOVE_DATA_IN | sizeof(SCp->sense_buffer)); 1029 slot->SG[0].pAddr = bS_to_host(slot->dma_handle); 1030 slot->SG[1].ins = bS_to_host(SCRIPT_RETURN); 1031 slot->SG[1].pAddr = 0; 1032 slot->resume_offset = hostdata->pScript; 1033 dma_cache_sync(slot->SG, sizeof(slot->SG[0])*2, DMA_TO_DEVICE); 1034 dma_cache_sync(SCp->sense_buffer, sizeof(SCp->sense_buffer), DMA_FROM_DEVICE); 1035 1036 /* queue the command for reissue */ 1037 slot->state = NCR_700_SLOT_QUEUED; 1038 hostdata->state = NCR_700_HOST_FREE; 1039 hostdata->cmd = NULL; 1040 } 1041 } else { 1042 // Currently rely on the mid layer evaluation 1043 // of the tag queuing capability 1044 // 1045 //if(status_byte(hostdata->status[0]) == GOOD && 1046 // SCp->cmnd[0] == INQUIRY && SCp->use_sg == 0) { 1047 // /* Piggy back the tag queueing support 1048 // * on this command */ 1049 // dma_sync_single_for_cpu(hostdata->dev, 1050 // slot->dma_handle, 1051 // SCp->request_bufflen, 1052 // DMA_FROM_DEVICE); 1053 // if(((char *)SCp->request_buffer)[7] & 0x02) { 1054 // scmd_printk(KERN_INFO, SCp, 1055 // "Enabling Tag Command Queuing\n"); 1056 // hostdata->tag_negotiated |= (1<<scmd_id(SCp)); 1057 // NCR_700_set_flag(SCp->device, NCR_700_DEV_BEGIN_TAG_QUEUEING); 1058 // } else { 1059 // NCR_700_clear_flag(SCp->device, NCR_700_DEV_BEGIN_TAG_QUEUEING); 1060 // hostdata->tag_negotiated &= ~(1<<scmd_id(SCp)); 1061 // } 1062 //} 1063 NCR_700_scsi_done(hostdata, SCp, hostdata->status[0]); 1064 } 1065 } else if((dsps & 0xfffff0f0) == A_UNEXPECTED_PHASE) { 1066 __u8 i = (dsps & 0xf00) >> 8; 1067 1068 scmd_printk(KERN_ERR, SCp, "UNEXPECTED PHASE %s (%s)\n", 1069 NCR_700_phase[i], 1070 sbcl_to_string(NCR_700_readb(host, SBCL_REG))); 1071 scmd_printk(KERN_ERR, SCp, " len = %d, cmd =", 1072 SCp->cmd_len); 1073 scsi_print_command(SCp); 1074 1075 NCR_700_internal_bus_reset(host); 1076 } else if((dsps & 0xfffff000) == A_FATAL) { 1077 int i = (dsps & 0xfff); 1078 1079 printk(KERN_ERR "scsi%d: (%d:%d) FATAL ERROR: %s\n", 1080 host->host_no, pun, lun, NCR_700_fatal_messages[i]); 1081 if(dsps == A_FATAL_ILLEGAL_MSG_LENGTH) { 1082 printk(KERN_ERR " msg begins %02x %02x\n", 1083 hostdata->msgin[0], hostdata->msgin[1]); 1084 } 1085 NCR_700_internal_bus_reset(host); 1086 } else if((dsps & 0xfffff0f0) == A_DISCONNECT) { 1087 #ifdef NCR_700_DEBUG 1088 __u8 i = (dsps & 0xf00) >> 8; 1089 1090 printk("scsi%d: (%d:%d), DISCONNECTED (%d) %s\n", 1091 host->host_no, pun, lun, 1092 i, NCR_700_phase[i]); 1093 #endif 1094 save_for_reselection(hostdata, SCp, dsp); 1095 1096 } else if(dsps == A_RESELECTION_IDENTIFIED) { 1097 __u8 lun; 1098 struct NCR_700_command_slot *slot; 1099 __u8 reselection_id = hostdata->reselection_id; 1100 struct scsi_device *SDp; 1101 1102 lun = hostdata->msgin[0] & 0x1f; 1103 1104 hostdata->reselection_id = 0xff; 1105 DEBUG(("scsi%d: (%d:%d) RESELECTED!\n", 1106 host->host_no, reselection_id, lun)); 1107 /* clear the reselection indicator */ 1108 SDp = __scsi_device_lookup(host, 0, reselection_id, lun); 1109 if(unlikely(SDp == NULL)) { 1110 printk(KERN_ERR "scsi%d: (%d:%d) HAS NO device\n", 1111 host->host_no, reselection_id, lun); 1112 BUG(); 1113 } 1114 if(hostdata->msgin[1] == A_SIMPLE_TAG_MSG) { 1115 struct scsi_cmnd *SCp = scsi_find_tag(SDp, hostdata->msgin[2]); 1116 if(unlikely(SCp == NULL)) { 1117 printk(KERN_ERR "scsi%d: (%d:%d) no saved request for tag %d\n", 1118 host->host_no, reselection_id, lun, hostdata->msgin[2]); 1119 BUG(); 1120 } 1121 1122 slot = (struct NCR_700_command_slot *)SCp->host_scribble; 1123 DDEBUG(KERN_DEBUG, SDp, 1124 "reselection is tag %d, slot %p(%d)\n", 1125 hostdata->msgin[2], slot, slot->tag); 1126 } else { 1127 struct scsi_cmnd *SCp = scsi_find_tag(SDp, SCSI_NO_TAG); 1128 if(unlikely(SCp == NULL)) { 1129 sdev_printk(KERN_ERR, SDp, 1130 "no saved request for untagged cmd\n"); 1131 BUG(); 1132 } 1133 slot = (struct NCR_700_command_slot *)SCp->host_scribble; 1134 } 1135 1136 if(slot == NULL) { 1137 printk(KERN_ERR "scsi%d: (%d:%d) RESELECTED but no saved command (MSG = %02x %02x %02x)!!\n", 1138 host->host_no, reselection_id, lun, 1139 hostdata->msgin[0], hostdata->msgin[1], 1140 hostdata->msgin[2]); 1141 } else { 1142 if(hostdata->state != NCR_700_HOST_BUSY) 1143 printk(KERN_ERR "scsi%d: FATAL, host not busy during valid reselection!\n", 1144 host->host_no); 1145 resume_offset = slot->resume_offset; 1146 hostdata->cmd = slot->cmnd; 1147 1148 /* re-patch for this command */ 1149 script_patch_32_abs(hostdata->script, CommandAddress, 1150 slot->pCmd); 1151 script_patch_16(hostdata->script, 1152 CommandCount, slot->cmnd->cmd_len); 1153 script_patch_32_abs(hostdata->script, SGScriptStartAddress, 1154 to32bit(&slot->pSG[0].ins)); 1155 1156 /* Note: setting SXFER only works if we're 1157 * still in the MESSAGE phase, so it is vital 1158 * that ACK is still asserted when we process 1159 * the reselection message. The resume offset 1160 * should therefore always clear ACK */ 1161 NCR_700_writeb(NCR_700_get_SXFER(hostdata->cmd->device), 1162 host, SXFER_REG); 1163 dma_cache_sync(hostdata->msgin, 1164 MSG_ARRAY_SIZE, DMA_FROM_DEVICE); 1165 dma_cache_sync(hostdata->msgout, 1166 MSG_ARRAY_SIZE, DMA_TO_DEVICE); 1167 /* I'm just being paranoid here, the command should 1168 * already have been flushed from the cache */ 1169 dma_cache_sync(slot->cmnd->cmnd, 1170 slot->cmnd->cmd_len, DMA_TO_DEVICE); 1171 1172 1173 1174 } 1175 } else if(dsps == A_RESELECTED_DURING_SELECTION) { 1176 1177 /* This section is full of debugging code because I've 1178 * never managed to reach it. I think what happens is 1179 * that, because the 700 runs with selection 1180 * interrupts enabled the whole time that we take a 1181 * selection interrupt before we manage to get to the 1182 * reselected script interrupt */ 1183 1184 __u8 reselection_id = NCR_700_readb(host, SFBR_REG); 1185 struct NCR_700_command_slot *slot; 1186 1187 /* Take out our own ID */ 1188 reselection_id &= ~(1<<host->this_id); 1189 1190 /* I've never seen this happen, so keep this as a printk rather 1191 * than a debug */ 1192 printk(KERN_INFO "scsi%d: (%d:%d) RESELECTION DURING SELECTION, dsp=%08x[%04x] state=%d, count=%d\n", 1193 host->host_no, reselection_id, lun, dsp, dsp - hostdata->pScript, hostdata->state, hostdata->command_slot_count); 1194 1195 { 1196 /* FIXME: DEBUGGING CODE */ 1197 __u32 SG = (__u32)bS_to_cpu(hostdata->script[A_SGScriptStartAddress_used[0]]); 1198 int i; 1199 1200 for(i=0; i< NCR_700_COMMAND_SLOTS_PER_HOST; i++) { 1201 if(SG >= to32bit(&hostdata->slots[i].pSG[0]) 1202 && SG <= to32bit(&hostdata->slots[i].pSG[NCR_700_SG_SEGMENTS])) 1203 break; 1204 } 1205 printk(KERN_INFO "IDENTIFIED SG segment as being %08x in slot %p, cmd %p, slot->resume_offset=%08x\n", SG, &hostdata->slots[i], hostdata->slots[i].cmnd, hostdata->slots[i].resume_offset); 1206 SCp = hostdata->slots[i].cmnd; 1207 } 1208 1209 if(SCp != NULL) { 1210 slot = (struct NCR_700_command_slot *)SCp->host_scribble; 1211 /* change slot from busy to queued to redo command */ 1212 slot->state = NCR_700_SLOT_QUEUED; 1213 } 1214 hostdata->cmd = NULL; 1215 1216 if(reselection_id == 0) { 1217 if(hostdata->reselection_id == 0xff) { 1218 printk(KERN_ERR "scsi%d: Invalid reselection during selection!!\n", host->host_no); 1219 return 0; 1220 } else { 1221 printk(KERN_ERR "scsi%d: script reselected and we took a selection interrupt\n", 1222 host->host_no); 1223 reselection_id = hostdata->reselection_id; 1224 } 1225 } else { 1226 1227 /* convert to real ID */ 1228 reselection_id = bitmap_to_number(reselection_id); 1229 } 1230 hostdata->reselection_id = reselection_id; 1231 /* just in case we have a stale simple tag message, clear it */ 1232 hostdata->msgin[1] = 0; 1233 dma_cache_sync(hostdata->msgin, 1234 MSG_ARRAY_SIZE, DMA_BIDIRECTIONAL); 1235 if(hostdata->tag_negotiated & (1<<reselection_id)) { 1236 resume_offset = hostdata->pScript + Ent_GetReselectionWithTag; 1237 } else { 1238 resume_offset = hostdata->pScript + Ent_GetReselectionData; 1239 } 1240 } else if(dsps == A_COMPLETED_SELECTION_AS_TARGET) { 1241 /* we've just disconnected from the bus, do nothing since 1242 * a return here will re-run the queued command slot 1243 * that may have been interrupted by the initial selection */ 1244 DEBUG((" SELECTION COMPLETED\n")); 1245 } else if((dsps & 0xfffff0f0) == A_MSG_IN) { 1246 resume_offset = process_message(host, hostdata, SCp, 1247 dsp, dsps); 1248 } else if((dsps & 0xfffff000) == 0) { 1249 __u8 i = (dsps & 0xf0) >> 4, j = (dsps & 0xf00) >> 8; 1250 printk(KERN_ERR "scsi%d: (%d:%d), unhandled script condition %s %s at %04x\n", 1251 host->host_no, pun, lun, NCR_700_condition[i], 1252 NCR_700_phase[j], dsp - hostdata->pScript); 1253 if(SCp != NULL) { 1254 scsi_print_command(SCp); 1255 1256 if(SCp->use_sg) { 1257 for(i = 0; i < SCp->use_sg + 1; i++) { 1258 printk(KERN_INFO " SG[%d].length = %d, move_insn=%08x, addr %08x\n", i, ((struct scatterlist *)SCp->buffer)[i].length, ((struct NCR_700_command_slot *)SCp->host_scribble)->SG[i].ins, ((struct NCR_700_command_slot *)SCp->host_scribble)->SG[i].pAddr); 1259 } 1260 } 1261 } 1262 NCR_700_internal_bus_reset(host); 1263 } else if((dsps & 0xfffff000) == A_DEBUG_INTERRUPT) { 1264 printk(KERN_NOTICE "scsi%d (%d:%d) DEBUG INTERRUPT %d AT %08x[%04x], continuing\n", 1265 host->host_no, pun, lun, dsps & 0xfff, dsp, dsp - hostdata->pScript); 1266 resume_offset = dsp; 1267 } else { 1268 printk(KERN_ERR "scsi%d: (%d:%d), unidentified script interrupt 0x%x at %04x\n", 1269 host->host_no, pun, lun, dsps, dsp - hostdata->pScript); 1270 NCR_700_internal_bus_reset(host); 1271 } 1272 return resume_offset; 1273 } 1274 1275 /* We run the 53c700 with selection interrupts always enabled. This 1276 * means that the chip may be selected as soon as the bus frees. On a 1277 * busy bus, this can be before the scripts engine finishes its 1278 * processing. Therefore, part of the selection processing has to be 1279 * to find out what the scripts engine is doing and complete the 1280 * function if necessary (i.e. process the pending disconnect or save 1281 * the interrupted initial selection */ 1282 STATIC inline __u32 1283 process_selection(struct Scsi_Host *host, __u32 dsp) 1284 { 1285 __u8 id = 0; /* Squash compiler warning */ 1286 int count = 0; 1287 __u32 resume_offset = 0; 1288 struct NCR_700_Host_Parameters *hostdata = 1289 (struct NCR_700_Host_Parameters *)host->hostdata[0]; 1290 struct scsi_cmnd *SCp = hostdata->cmd; 1291 __u8 sbcl; 1292 1293 for(count = 0; count < 5; count++) { 1294 id = NCR_700_readb(host, hostdata->chip710 ? 1295 CTEST9_REG : SFBR_REG); 1296 1297 /* Take out our own ID */ 1298 id &= ~(1<<host->this_id); 1299 if(id != 0) 1300 break; 1301 udelay(5); 1302 } 1303 sbcl = NCR_700_readb(host, SBCL_REG); 1304 if((sbcl & SBCL_IO) == 0) { 1305 /* mark as having been selected rather than reselected */ 1306 id = 0xff; 1307 } else { 1308 /* convert to real ID */ 1309 hostdata->reselection_id = id = bitmap_to_number(id); 1310 DEBUG(("scsi%d: Reselected by %d\n", 1311 host->host_no, id)); 1312 } 1313 if(hostdata->state == NCR_700_HOST_BUSY && SCp != NULL) { 1314 struct NCR_700_command_slot *slot = 1315 (struct NCR_700_command_slot *)SCp->host_scribble; 1316 DEBUG((" ID %d WARNING: RESELECTION OF BUSY HOST, saving cmd %p, slot %p, addr %x [%04x], resume %x!\n", id, hostdata->cmd, slot, dsp, dsp - hostdata->pScript, resume_offset)); 1317 1318 switch(dsp - hostdata->pScript) { 1319 case Ent_Disconnect1: 1320 case Ent_Disconnect2: 1321 save_for_reselection(hostdata, SCp, Ent_Disconnect2 + hostdata->pScript); 1322 break; 1323 case Ent_Disconnect3: 1324 case Ent_Disconnect4: 1325 save_for_reselection(hostdata, SCp, Ent_Disconnect4 + hostdata->pScript); 1326 break; 1327 case Ent_Disconnect5: 1328 case Ent_Disconnect6: 1329 save_for_reselection(hostdata, SCp, Ent_Disconnect6 + hostdata->pScript); 1330 break; 1331 case Ent_Disconnect7: 1332 case Ent_Disconnect8: 1333 save_for_reselection(hostdata, SCp, Ent_Disconnect8 + hostdata->pScript); 1334 break; 1335 case Ent_Finish1: 1336 case Ent_Finish2: 1337 process_script_interrupt(A_GOOD_STATUS_AFTER_STATUS, dsp, SCp, host, hostdata); 1338 break; 1339 1340 default: 1341 slot->state = NCR_700_SLOT_QUEUED; 1342 break; 1343 } 1344 } 1345 hostdata->state = NCR_700_HOST_BUSY; 1346 hostdata->cmd = NULL; 1347 /* clear any stale simple tag message */ 1348 hostdata->msgin[1] = 0; 1349 dma_cache_sync(hostdata->msgin, MSG_ARRAY_SIZE, 1350 DMA_BIDIRECTIONAL); 1351 1352 if(id == 0xff) { 1353 /* Selected as target, Ignore */ 1354 resume_offset = hostdata->pScript + Ent_SelectedAsTarget; 1355 } else if(hostdata->tag_negotiated & (1<<id)) { 1356 resume_offset = hostdata->pScript + Ent_GetReselectionWithTag; 1357 } else { 1358 resume_offset = hostdata->pScript + Ent_GetReselectionData; 1359 } 1360 return resume_offset; 1361 } 1362 1363 static inline void 1364 NCR_700_clear_fifo(struct Scsi_Host *host) { 1365 const struct NCR_700_Host_Parameters *hostdata 1366 = (struct NCR_700_Host_Parameters *)host->hostdata[0]; 1367 if(hostdata->chip710) { 1368 NCR_700_writeb(CLR_FIFO_710, host, CTEST8_REG); 1369 } else { 1370 NCR_700_writeb(CLR_FIFO, host, DFIFO_REG); 1371 } 1372 } 1373 1374 static inline void 1375 NCR_700_flush_fifo(struct Scsi_Host *host) { 1376 const struct NCR_700_Host_Parameters *hostdata 1377 = (struct NCR_700_Host_Parameters *)host->hostdata[0]; 1378 if(hostdata->chip710) { 1379 NCR_700_writeb(FLUSH_DMA_FIFO_710, host, CTEST8_REG); 1380 udelay(10); 1381 NCR_700_writeb(0, host, CTEST8_REG); 1382 } else { 1383 NCR_700_writeb(FLUSH_DMA_FIFO, host, DFIFO_REG); 1384 udelay(10); 1385 NCR_700_writeb(0, host, DFIFO_REG); 1386 } 1387 } 1388 1389 1390 /* The queue lock with interrupts disabled must be held on entry to 1391 * this function */ 1392 STATIC int 1393 NCR_700_start_command(struct scsi_cmnd *SCp) 1394 { 1395 struct NCR_700_command_slot *slot = 1396 (struct NCR_700_command_slot *)SCp->host_scribble; 1397 struct NCR_700_Host_Parameters *hostdata = 1398 (struct NCR_700_Host_Parameters *)SCp->device->host->hostdata[0]; 1399 __u16 count = 1; /* for IDENTIFY message */ 1400 1401 if(hostdata->state != NCR_700_HOST_FREE) { 1402 /* keep this inside the lock to close the race window where 1403 * the running command finishes on another CPU while we don't 1404 * change the state to queued on this one */ 1405 slot->state = NCR_700_SLOT_QUEUED; 1406 1407 DEBUG(("scsi%d: host busy, queueing command %p, slot %p\n", 1408 SCp->device->host->host_no, slot->cmnd, slot)); 1409 return 0; 1410 } 1411 hostdata->state = NCR_700_HOST_BUSY; 1412 hostdata->cmd = SCp; 1413 slot->state = NCR_700_SLOT_BUSY; 1414 /* keep interrupts disabled until we have the command correctly 1415 * set up so we cannot take a selection interrupt */ 1416 1417 hostdata->msgout[0] = NCR_700_identify(SCp->cmnd[0] != REQUEST_SENSE, 1418 SCp->device->lun); 1419 /* for INQUIRY or REQUEST_SENSE commands, we cannot be sure 1420 * if the negotiated transfer parameters still hold, so 1421 * always renegotiate them */ 1422 if(SCp->cmnd[0] == INQUIRY || SCp->cmnd[0] == REQUEST_SENSE) { 1423 NCR_700_clear_flag(SCp->device, NCR_700_DEV_NEGOTIATED_SYNC); 1424 } 1425 1426 /* REQUEST_SENSE is asking for contingent I_T_L(_Q) status. 1427 * If a contingent allegiance condition exists, the device 1428 * will refuse all tags, so send the request sense as untagged 1429 * */ 1430 if((hostdata->tag_negotiated & (1<<scmd_id(SCp))) 1431 && (slot->tag != SCSI_NO_TAG && SCp->cmnd[0] != REQUEST_SENSE)) { 1432 count += scsi_populate_tag_msg(SCp, &hostdata->msgout[count]); 1433 } 1434 1435 if(hostdata->fast && 1436 NCR_700_is_flag_clear(SCp->device, NCR_700_DEV_NEGOTIATED_SYNC)) { 1437 memcpy(&hostdata->msgout[count], NCR_700_SDTR_msg, 1438 sizeof(NCR_700_SDTR_msg)); 1439 hostdata->msgout[count+3] = spi_period(SCp->device->sdev_target); 1440 hostdata->msgout[count+4] = spi_offset(SCp->device->sdev_target); 1441 count += sizeof(NCR_700_SDTR_msg); 1442 NCR_700_set_flag(SCp->device, NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); 1443 } 1444 1445 script_patch_16(hostdata->script, MessageCount, count); 1446 1447 1448 script_patch_ID(hostdata->script, 1449 Device_ID, 1<<scmd_id(SCp)); 1450 1451 script_patch_32_abs(hostdata->script, CommandAddress, 1452 slot->pCmd); 1453 script_patch_16(hostdata->script, CommandCount, SCp->cmd_len); 1454 /* finally plumb the beginning of the SG list into the script 1455 * */ 1456 script_patch_32_abs(hostdata->script, SGScriptStartAddress, 1457 to32bit(&slot->pSG[0].ins)); 1458 NCR_700_clear_fifo(SCp->device->host); 1459 1460 if(slot->resume_offset == 0) 1461 slot->resume_offset = hostdata->pScript; 1462 /* now perform all the writebacks and invalidates */ 1463 dma_cache_sync(hostdata->msgout, count, DMA_TO_DEVICE); 1464 dma_cache_sync(hostdata->msgin, MSG_ARRAY_SIZE, 1465 DMA_FROM_DEVICE); 1466 dma_cache_sync(SCp->cmnd, SCp->cmd_len, DMA_TO_DEVICE); 1467 dma_cache_sync(hostdata->status, 1, DMA_FROM_DEVICE); 1468 1469 /* set the synchronous period/offset */ 1470 NCR_700_writeb(NCR_700_get_SXFER(SCp->device), 1471 SCp->device->host, SXFER_REG); 1472 NCR_700_writel(slot->temp, SCp->device->host, TEMP_REG); 1473 NCR_700_writel(slot->resume_offset, SCp->device->host, DSP_REG); 1474 1475 return 1; 1476 } 1477 1478 irqreturn_t 1479 NCR_700_intr(int irq, void *dev_id, struct pt_regs *regs) 1480 { 1481 struct Scsi_Host *host = (struct Scsi_Host *)dev_id; 1482 struct NCR_700_Host_Parameters *hostdata = 1483 (struct NCR_700_Host_Parameters *)host->hostdata[0]; 1484 __u8 istat; 1485 __u32 resume_offset = 0; 1486 __u8 pun = 0xff, lun = 0xff; 1487 unsigned long flags; 1488 int handled = 0; 1489 1490 /* Use the host lock to serialise acess to the 53c700 1491 * hardware. Note: In future, we may need to take the queue 1492 * lock to enter the done routines. When that happens, we 1493 * need to ensure that for this driver, the host lock and the 1494 * queue lock point to the same thing. */ 1495 spin_lock_irqsave(host->host_lock, flags); 1496 if((istat = NCR_700_readb(host, ISTAT_REG)) 1497 & (SCSI_INT_PENDING | DMA_INT_PENDING)) { 1498 __u32 dsps; 1499 __u8 sstat0 = 0, dstat = 0; 1500 __u32 dsp; 1501 struct scsi_cmnd *SCp = hostdata->cmd; 1502 enum NCR_700_Host_State state; 1503 1504 handled = 1; 1505 state = hostdata->state; 1506 SCp = hostdata->cmd; 1507 1508 if(istat & SCSI_INT_PENDING) { 1509 udelay(10); 1510 1511 sstat0 = NCR_700_readb(host, SSTAT0_REG); 1512 } 1513 1514 if(istat & DMA_INT_PENDING) { 1515 udelay(10); 1516 1517 dstat = NCR_700_readb(host, DSTAT_REG); 1518 } 1519 1520 dsps = NCR_700_readl(host, DSPS_REG); 1521 dsp = NCR_700_readl(host, DSP_REG); 1522 1523 DEBUG(("scsi%d: istat %02x sstat0 %02x dstat %02x dsp %04x[%08x] dsps 0x%x\n", 1524 host->host_no, istat, sstat0, dstat, 1525 (dsp - (__u32)(hostdata->pScript))/4, 1526 dsp, dsps)); 1527 1528 if(SCp != NULL) { 1529 pun = SCp->device->id; 1530 lun = SCp->device->lun; 1531 } 1532 1533 if(sstat0 & SCSI_RESET_DETECTED) { 1534 struct scsi_device *SDp; 1535 int i; 1536 1537 hostdata->state = NCR_700_HOST_BUSY; 1538 1539 printk(KERN_ERR "scsi%d: Bus Reset detected, executing command %p, slot %p, dsp %08x[%04x]\n", 1540 host->host_no, SCp, SCp == NULL ? NULL : SCp->host_scribble, dsp, dsp - hostdata->pScript); 1541 1542 scsi_report_bus_reset(host, 0); 1543 1544 /* clear all the negotiated parameters */ 1545 __shost_for_each_device(SDp, host) 1546 SDp->hostdata = NULL; 1547 1548 /* clear all the slots and their pending commands */ 1549 for(i = 0; i < NCR_700_COMMAND_SLOTS_PER_HOST; i++) { 1550 struct scsi_cmnd *SCp; 1551 struct NCR_700_command_slot *slot = 1552 &hostdata->slots[i]; 1553 1554 if(slot->state == NCR_700_SLOT_FREE) 1555 continue; 1556 1557 SCp = slot->cmnd; 1558 printk(KERN_ERR " failing command because of reset, slot %p, cmnd %p\n", 1559 slot, SCp); 1560 free_slot(slot, hostdata); 1561 SCp->host_scribble = NULL; 1562 NCR_700_set_depth(SCp->device, 0); 1563 /* NOTE: deadlock potential here: we 1564 * rely on mid-layer guarantees that 1565 * scsi_done won't try to issue the 1566 * command again otherwise we'll 1567 * deadlock on the 1568 * hostdata->state_lock */ 1569 SCp->result = DID_RESET << 16; 1570 SCp->scsi_done(SCp); 1571 } 1572 mdelay(25); 1573 NCR_700_chip_setup(host); 1574 1575 hostdata->state = NCR_700_HOST_FREE; 1576 hostdata->cmd = NULL; 1577 /* signal back if this was an eh induced reset */ 1578 if(hostdata->eh_complete != NULL) 1579 complete(hostdata->eh_complete); 1580 goto out_unlock; 1581 } else if(sstat0 & SELECTION_TIMEOUT) { 1582 DEBUG(("scsi%d: (%d:%d) selection timeout\n", 1583 host->host_no, pun, lun)); 1584 NCR_700_scsi_done(hostdata, SCp, DID_NO_CONNECT<<16); 1585 } else if(sstat0 & PHASE_MISMATCH) { 1586 struct NCR_700_command_slot *slot = (SCp == NULL) ? NULL : 1587 (struct NCR_700_command_slot *)SCp->host_scribble; 1588 1589 if(dsp == Ent_SendMessage + 8 + hostdata->pScript) { 1590 /* It wants to reply to some part of 1591 * our message */ 1592 #ifdef NCR_700_DEBUG 1593 __u32 temp = NCR_700_readl(host, TEMP_REG); 1594 int count = (hostdata->script[Ent_SendMessage/4] & 0xffffff) - ((NCR_700_readl(host, DBC_REG) & 0xffffff) + NCR_700_data_residual(host)); 1595 printk("scsi%d (%d:%d) PHASE MISMATCH IN SEND MESSAGE %d remain, return %p[%04x], phase %s\n", host->host_no, pun, lun, count, (void *)temp, temp - hostdata->pScript, sbcl_to_string(NCR_700_readb(host, SBCL_REG))); 1596 #endif 1597 resume_offset = hostdata->pScript + Ent_SendMessagePhaseMismatch; 1598 } else if(dsp >= to32bit(&slot->pSG[0].ins) && 1599 dsp <= to32bit(&slot->pSG[NCR_700_SG_SEGMENTS].ins)) { 1600 int data_transfer = NCR_700_readl(host, DBC_REG) & 0xffffff; 1601 int SGcount = (dsp - to32bit(&slot->pSG[0].ins))/sizeof(struct NCR_700_SG_List); 1602 int residual = NCR_700_data_residual(host); 1603 int i; 1604 #ifdef NCR_700_DEBUG 1605 __u32 naddr = NCR_700_readl(host, DNAD_REG); 1606 1607 printk("scsi%d: (%d:%d) Expected phase mismatch in slot->SG[%d], transferred 0x%x\n", 1608 host->host_no, pun, lun, 1609 SGcount, data_transfer); 1610 scsi_print_command(SCp); 1611 if(residual) { 1612 printk("scsi%d: (%d:%d) Expected phase mismatch in slot->SG[%d], transferred 0x%x, residual %d\n", 1613 host->host_no, pun, lun, 1614 SGcount, data_transfer, residual); 1615 } 1616 #endif 1617 data_transfer += residual; 1618 1619 if(data_transfer != 0) { 1620 int count; 1621 __u32 pAddr; 1622 1623 SGcount--; 1624 1625 count = (bS_to_cpu(slot->SG[SGcount].ins) & 0x00ffffff); 1626 DEBUG(("DATA TRANSFER MISMATCH, count = %d, transferred %d\n", count, count-data_transfer)); 1627 slot->SG[SGcount].ins &= bS_to_host(0xff000000); 1628 slot->SG[SGcount].ins |= bS_to_host(data_transfer); 1629 pAddr = bS_to_cpu(slot->SG[SGcount].pAddr); 1630 pAddr += (count - data_transfer); 1631 #ifdef NCR_700_DEBUG 1632 if(pAddr != naddr) { 1633 printk("scsi%d (%d:%d) transfer mismatch pAddr=%lx, naddr=%lx, data_transfer=%d, residual=%d\n", host->host_no, pun, lun, (unsigned long)pAddr, (unsigned long)naddr, data_transfer, residual); 1634 } 1635 #endif 1636 slot->SG[SGcount].pAddr = bS_to_host(pAddr); 1637 } 1638 /* set the executed moves to nops */ 1639 for(i=0; i<SGcount; i++) { 1640 slot->SG[i].ins = bS_to_host(SCRIPT_NOP); 1641 slot->SG[i].pAddr = 0; 1642 } 1643 dma_cache_sync(slot->SG, sizeof(slot->SG), DMA_TO_DEVICE); 1644 /* and pretend we disconnected after 1645 * the command phase */ 1646 resume_offset = hostdata->pScript + Ent_MsgInDuringData; 1647 /* make sure all the data is flushed */ 1648 NCR_700_flush_fifo(host); 1649 } else { 1650 __u8 sbcl = NCR_700_readb(host, SBCL_REG); 1651 printk(KERN_ERR "scsi%d: (%d:%d) phase mismatch at %04x, phase %s\n", 1652 host->host_no, pun, lun, dsp - hostdata->pScript, sbcl_to_string(sbcl)); 1653 NCR_700_internal_bus_reset(host); 1654 } 1655 1656 } else if(sstat0 & SCSI_GROSS_ERROR) { 1657 printk(KERN_ERR "scsi%d: (%d:%d) GROSS ERROR\n", 1658 host->host_no, pun, lun); 1659 NCR_700_scsi_done(hostdata, SCp, DID_ERROR<<16); 1660 } else if(sstat0 & PARITY_ERROR) { 1661 printk(KERN_ERR "scsi%d: (%d:%d) PARITY ERROR\n", 1662 host->host_no, pun, lun); 1663 NCR_700_scsi_done(hostdata, SCp, DID_ERROR<<16); 1664 } else if(dstat & SCRIPT_INT_RECEIVED) { 1665 DEBUG(("scsi%d: (%d:%d) ====>SCRIPT INTERRUPT<====\n", 1666 host->host_no, pun, lun)); 1667 resume_offset = process_script_interrupt(dsps, dsp, SCp, host, hostdata); 1668 } else if(dstat & (ILGL_INST_DETECTED)) { 1669 printk(KERN_ERR "scsi%d: (%d:%d) Illegal Instruction detected at 0x%08x[0x%x]!!!\n" 1670 " Please email James.Bottomley@HansenPartnership.com with the details\n", 1671 host->host_no, pun, lun, 1672 dsp, dsp - hostdata->pScript); 1673 NCR_700_scsi_done(hostdata, SCp, DID_ERROR<<16); 1674 } else if(dstat & (WATCH_DOG_INTERRUPT|ABORTED)) { 1675 printk(KERN_ERR "scsi%d: (%d:%d) serious DMA problem, dstat=%02x\n", 1676 host->host_no, pun, lun, dstat); 1677 NCR_700_scsi_done(hostdata, SCp, DID_ERROR<<16); 1678 } 1679 1680 1681 /* NOTE: selection interrupt processing MUST occur 1682 * after script interrupt processing to correctly cope 1683 * with the case where we process a disconnect and 1684 * then get reselected before we process the 1685 * disconnection */ 1686 if(sstat0 & SELECTED) { 1687 /* FIXME: It currently takes at least FOUR 1688 * interrupts to complete a command that 1689 * disconnects: one for the disconnect, one 1690 * for the reselection, one to get the 1691 * reselection data and one to complete the 1692 * command. If we guess the reselected 1693 * command here and prepare it, we only need 1694 * to get a reselection data interrupt if we 1695 * guessed wrongly. Since the interrupt 1696 * overhead is much greater than the command 1697 * setup, this would be an efficient 1698 * optimisation particularly as we probably 1699 * only have one outstanding command on a 1700 * target most of the time */ 1701 1702 resume_offset = process_selection(host, dsp); 1703 1704 } 1705 1706 } 1707 1708 if(resume_offset) { 1709 if(hostdata->state != NCR_700_HOST_BUSY) { 1710 printk(KERN_ERR "scsi%d: Driver error: resume at 0x%08x [0x%04x] with non busy host!\n", 1711 host->host_no, resume_offset, resume_offset - hostdata->pScript); 1712 hostdata->state = NCR_700_HOST_BUSY; 1713 } 1714 1715 DEBUG(("Attempting to resume at %x\n", resume_offset)); 1716 NCR_700_clear_fifo(host); 1717 NCR_700_writel(resume_offset, host, DSP_REG); 1718 } 1719 /* There is probably a technical no-no about this: If we're a 1720 * shared interrupt and we got this interrupt because the 1721 * other device needs servicing not us, we're still going to 1722 * check our queued commands here---of course, there shouldn't 1723 * be any outstanding.... */ 1724 if(hostdata->state == NCR_700_HOST_FREE) { 1725 int i; 1726 1727 for(i = 0; i < NCR_700_COMMAND_SLOTS_PER_HOST; i++) { 1728 /* fairness: always run the queue from the last 1729 * position we left off */ 1730 int j = (i + hostdata->saved_slot_position) 1731 % NCR_700_COMMAND_SLOTS_PER_HOST; 1732 1733 if(hostdata->slots[j].state != NCR_700_SLOT_QUEUED) 1734 continue; 1735 if(NCR_700_start_command(hostdata->slots[j].cmnd)) { 1736 DEBUG(("scsi%d: Issuing saved command slot %p, cmd %p\t\n", 1737 host->host_no, &hostdata->slots[j], 1738 hostdata->slots[j].cmnd)); 1739 hostdata->saved_slot_position = j + 1; 1740 } 1741 1742 break; 1743 } 1744 } 1745 out_unlock: 1746 spin_unlock_irqrestore(host->host_lock, flags); 1747 return IRQ_RETVAL(handled); 1748 } 1749 1750 STATIC int 1751 NCR_700_queuecommand(struct scsi_cmnd *SCp, void (*done)(struct scsi_cmnd *)) 1752 { 1753 struct NCR_700_Host_Parameters *hostdata = 1754 (struct NCR_700_Host_Parameters *)SCp->device->host->hostdata[0]; 1755 __u32 move_ins; 1756 enum dma_data_direction direction; 1757 struct NCR_700_command_slot *slot; 1758 1759 if(hostdata->command_slot_count >= NCR_700_COMMAND_SLOTS_PER_HOST) { 1760 /* We're over our allocation, this should never happen 1761 * since we report the max allocation to the mid layer */ 1762 printk(KERN_WARNING "scsi%d: Command depth has gone over queue depth\n", SCp->device->host->host_no); 1763 return 1; 1764 } 1765 /* check for untagged commands. We cannot have any outstanding 1766 * commands if we accept them. Commands could be untagged because: 1767 * 1768 * - The tag negotiated bitmap is clear 1769 * - The blk layer sent and untagged command 1770 */ 1771 if(NCR_700_get_depth(SCp->device) != 0 1772 && (!(hostdata->tag_negotiated & (1<<scmd_id(SCp))) 1773 || !blk_rq_tagged(SCp->request))) { 1774 CDEBUG(KERN_ERR, SCp, "has non zero depth %d\n", 1775 NCR_700_get_depth(SCp->device)); 1776 return SCSI_MLQUEUE_DEVICE_BUSY; 1777 } 1778 if(NCR_700_get_depth(SCp->device) >= SCp->device->queue_depth) { 1779 CDEBUG(KERN_ERR, SCp, "has max tag depth %d\n", 1780 NCR_700_get_depth(SCp->device)); 1781 return SCSI_MLQUEUE_DEVICE_BUSY; 1782 } 1783 NCR_700_set_depth(SCp->device, NCR_700_get_depth(SCp->device) + 1); 1784 1785 /* begin the command here */ 1786 /* no need to check for NULL, test for command_slot_count above 1787 * ensures a slot is free */ 1788 slot = find_empty_slot(hostdata); 1789 1790 slot->cmnd = SCp; 1791 1792 SCp->scsi_done = done; 1793 SCp->host_scribble = (unsigned char *)slot; 1794 SCp->SCp.ptr = NULL; 1795 SCp->SCp.buffer = NULL; 1796 1797 #ifdef NCR_700_DEBUG 1798 printk("53c700: scsi%d, command ", SCp->device->host->host_no); 1799 scsi_print_command(SCp); 1800 #endif 1801 if(blk_rq_tagged(SCp->request) 1802 && (hostdata->tag_negotiated &(1<<scmd_id(SCp))) == 0 1803 && NCR_700_get_tag_neg_state(SCp->device) == NCR_700_START_TAG_NEGOTIATION) { 1804 scmd_printk(KERN_ERR, SCp, "Enabling Tag Command Queuing\n"); 1805 hostdata->tag_negotiated |= (1<<scmd_id(SCp)); 1806 NCR_700_set_tag_neg_state(SCp->device, NCR_700_DURING_TAG_NEGOTIATION); 1807 } 1808 1809 /* here we may have to process an untagged command. The gate 1810 * above ensures that this will be the only one outstanding, 1811 * so clear the tag negotiated bit. 1812 * 1813 * FIXME: This will royally screw up on multiple LUN devices 1814 * */ 1815 if(!blk_rq_tagged(SCp->request) 1816 && (hostdata->tag_negotiated &(1<<scmd_id(SCp)))) { 1817 scmd_printk(KERN_INFO, SCp, "Disabling Tag Command Queuing\n"); 1818 hostdata->tag_negotiated &= ~(1<<scmd_id(SCp)); 1819 } 1820 1821 if((hostdata->tag_negotiated &(1<<scmd_id(SCp))) 1822 && scsi_get_tag_type(SCp->device)) { 1823 slot->tag = SCp->request->tag; 1824 CDEBUG(KERN_DEBUG, SCp, "sending out tag %d, slot %p\n", 1825 slot->tag, slot); 1826 } else { 1827 slot->tag = SCSI_NO_TAG; 1828 /* must populate current_cmnd for scsi_find_tag to work */ 1829 SCp->device->current_cmnd = SCp; 1830 } 1831 /* sanity check: some of the commands generated by the mid-layer 1832 * have an eccentric idea of their sc_data_direction */ 1833 if(!SCp->use_sg && !SCp->request_bufflen 1834 && SCp->sc_data_direction != DMA_NONE) { 1835 #ifdef NCR_700_DEBUG 1836 printk("53c700: Command"); 1837 scsi_print_command(SCp); 1838 printk("Has wrong data direction %d\n", SCp->sc_data_direction); 1839 #endif 1840 SCp->sc_data_direction = DMA_NONE; 1841 } 1842 1843 switch (SCp->cmnd[0]) { 1844 case REQUEST_SENSE: 1845 /* clear the internal sense magic */ 1846 SCp->cmnd[6] = 0; 1847 /* fall through */ 1848 default: 1849 /* OK, get it from the command */ 1850 switch(SCp->sc_data_direction) { 1851 case DMA_BIDIRECTIONAL: 1852 default: 1853 printk(KERN_ERR "53c700: Unknown command for data direction "); 1854 scsi_print_command(SCp); 1855 1856 move_ins = 0; 1857 break; 1858 case DMA_NONE: 1859 move_ins = 0; 1860 break; 1861 case DMA_FROM_DEVICE: 1862 move_ins = SCRIPT_MOVE_DATA_IN; 1863 break; 1864 case DMA_TO_DEVICE: 1865 move_ins = SCRIPT_MOVE_DATA_OUT; 1866 break; 1867 } 1868 } 1869 1870 /* now build the scatter gather list */ 1871 direction = SCp->sc_data_direction; 1872 if(move_ins != 0) { 1873 int i; 1874 int sg_count; 1875 dma_addr_t vPtr = 0; 1876 __u32 count = 0; 1877 1878 if(SCp->use_sg) { 1879 sg_count = dma_map_sg(hostdata->dev, SCp->buffer, 1880 SCp->use_sg, direction); 1881 } else { 1882 vPtr = dma_map_single(hostdata->dev, 1883 SCp->request_buffer, 1884 SCp->request_bufflen, 1885 direction); 1886 count = SCp->request_bufflen; 1887 slot->dma_handle = vPtr; 1888 sg_count = 1; 1889 } 1890 1891 1892 for(i = 0; i < sg_count; i++) { 1893 1894 if(SCp->use_sg) { 1895 struct scatterlist *sg = SCp->buffer; 1896 1897 vPtr = sg_dma_address(&sg[i]); 1898 count = sg_dma_len(&sg[i]); 1899 } 1900 1901 slot->SG[i].ins = bS_to_host(move_ins | count); 1902 DEBUG((" scatter block %d: move %d[%08x] from 0x%lx\n", 1903 i, count, slot->SG[i].ins, (unsigned long)vPtr)); 1904 slot->SG[i].pAddr = bS_to_host(vPtr); 1905 } 1906 slot->SG[i].ins = bS_to_host(SCRIPT_RETURN); 1907 slot->SG[i].pAddr = 0; 1908 dma_cache_sync(slot->SG, sizeof(slot->SG), DMA_TO_DEVICE); 1909 DEBUG((" SETTING %08lx to %x\n", 1910 (&slot->pSG[i].ins), 1911 slot->SG[i].ins)); 1912 } 1913 slot->resume_offset = 0; 1914 slot->pCmd = dma_map_single(hostdata->dev, SCp->cmnd, 1915 sizeof(SCp->cmnd), DMA_TO_DEVICE); 1916 NCR_700_start_command(SCp); 1917 return 0; 1918 } 1919 1920 STATIC int 1921 NCR_700_abort(struct scsi_cmnd * SCp) 1922 { 1923 struct NCR_700_command_slot *slot; 1924 1925 scmd_printk(KERN_INFO, SCp, 1926 "New error handler wants to abort command\n\t"); 1927 scsi_print_command(SCp); 1928 1929 slot = (struct NCR_700_command_slot *)SCp->host_scribble; 1930 1931 if(slot == NULL) 1932 /* no outstanding command to abort */ 1933 return SUCCESS; 1934 if(SCp->cmnd[0] == TEST_UNIT_READY) { 1935 /* FIXME: This is because of a problem in the new 1936 * error handler. When it is in error recovery, it 1937 * will send a TUR to a device it thinks may still be 1938 * showing a problem. If the TUR isn't responded to, 1939 * it will abort it and mark the device off line. 1940 * Unfortunately, it does no other error recovery, so 1941 * this would leave us with an outstanding command 1942 * occupying a slot. Rather than allow this to 1943 * happen, we issue a bus reset to force all 1944 * outstanding commands to terminate here. */ 1945 NCR_700_internal_bus_reset(SCp->device->host); 1946 /* still drop through and return failed */ 1947 } 1948 return FAILED; 1949 1950 } 1951 1952 STATIC int 1953 NCR_700_bus_reset(struct scsi_cmnd * SCp) 1954 { 1955 DECLARE_COMPLETION(complete); 1956 struct NCR_700_Host_Parameters *hostdata = 1957 (struct NCR_700_Host_Parameters *)SCp->device->host->hostdata[0]; 1958 1959 scmd_printk(KERN_INFO, SCp, 1960 "New error handler wants BUS reset, cmd %p\n\t", SCp); 1961 scsi_print_command(SCp); 1962 1963 /* In theory, eh_complete should always be null because the 1964 * eh is single threaded, but just in case we're handling a 1965 * reset via sg or something */ 1966 spin_lock_irq(SCp->device->host->host_lock); 1967 while (hostdata->eh_complete != NULL) { 1968 spin_unlock_irq(SCp->device->host->host_lock); 1969 msleep_interruptible(100); 1970 spin_lock_irq(SCp->device->host->host_lock); 1971 } 1972 1973 hostdata->eh_complete = &complete; 1974 NCR_700_internal_bus_reset(SCp->device->host); 1975 1976 spin_unlock_irq(SCp->device->host->host_lock); 1977 wait_for_completion(&complete); 1978 spin_lock_irq(SCp->device->host->host_lock); 1979 1980 hostdata->eh_complete = NULL; 1981 /* Revalidate the transport parameters of the failing device */ 1982 if(hostdata->fast) 1983 spi_schedule_dv_device(SCp->device); 1984 1985 spin_unlock_irq(SCp->device->host->host_lock); 1986 return SUCCESS; 1987 } 1988 1989 STATIC int 1990 NCR_700_host_reset(struct scsi_cmnd * SCp) 1991 { 1992 scmd_printk(KERN_INFO, SCp, "New error handler wants HOST reset\n\t"); 1993 scsi_print_command(SCp); 1994 1995 spin_lock_irq(SCp->device->host->host_lock); 1996 1997 NCR_700_internal_bus_reset(SCp->device->host); 1998 NCR_700_chip_reset(SCp->device->host); 1999 2000 spin_unlock_irq(SCp->device->host->host_lock); 2001 2002 return SUCCESS; 2003 } 2004 2005 STATIC void 2006 NCR_700_set_period(struct scsi_target *STp, int period) 2007 { 2008 struct Scsi_Host *SHp = dev_to_shost(STp->dev.parent); 2009 struct NCR_700_Host_Parameters *hostdata = 2010 (struct NCR_700_Host_Parameters *)SHp->hostdata[0]; 2011 2012 if(!hostdata->fast) 2013 return; 2014 2015 if(period < hostdata->min_period) 2016 period = hostdata->min_period; 2017 2018 spi_period(STp) = period; 2019 spi_flags(STp) &= ~(NCR_700_DEV_NEGOTIATED_SYNC | 2020 NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); 2021 spi_flags(STp) |= NCR_700_DEV_PRINT_SYNC_NEGOTIATION; 2022 } 2023 2024 STATIC void 2025 NCR_700_set_offset(struct scsi_target *STp, int offset) 2026 { 2027 struct Scsi_Host *SHp = dev_to_shost(STp->dev.parent); 2028 struct NCR_700_Host_Parameters *hostdata = 2029 (struct NCR_700_Host_Parameters *)SHp->hostdata[0]; 2030 int max_offset = hostdata->chip710 2031 ? NCR_710_MAX_OFFSET : NCR_700_MAX_OFFSET; 2032 2033 if(!hostdata->fast) 2034 return; 2035 2036 if(offset > max_offset) 2037 offset = max_offset; 2038 2039 /* if we're currently async, make sure the period is reasonable */ 2040 if(spi_offset(STp) == 0 && (spi_period(STp) < hostdata->min_period || 2041 spi_period(STp) > 0xff)) 2042 spi_period(STp) = hostdata->min_period; 2043 2044 spi_offset(STp) = offset; 2045 spi_flags(STp) &= ~(NCR_700_DEV_NEGOTIATED_SYNC | 2046 NCR_700_DEV_BEGIN_SYNC_NEGOTIATION); 2047 spi_flags(STp) |= NCR_700_DEV_PRINT_SYNC_NEGOTIATION; 2048 } 2049 2050 2051 2052 STATIC int 2053 NCR_700_slave_configure(struct scsi_device *SDp) 2054 { 2055 struct NCR_700_Host_Parameters *hostdata = 2056 (struct NCR_700_Host_Parameters *)SDp->host->hostdata[0]; 2057 2058 /* to do here: allocate memory; build a queue_full list */ 2059 if(SDp->tagged_supported) { 2060 scsi_set_tag_type(SDp, MSG_ORDERED_TAG); 2061 scsi_activate_tcq(SDp, NCR_700_DEFAULT_TAGS); 2062 NCR_700_set_tag_neg_state(SDp, NCR_700_START_TAG_NEGOTIATION); 2063 } else { 2064 /* initialise to default depth */ 2065 scsi_adjust_queue_depth(SDp, 0, SDp->host->cmd_per_lun); 2066 } 2067 if(hostdata->fast) { 2068 /* Find the correct offset and period via domain validation */ 2069 if (!spi_initial_dv(SDp->sdev_target)) 2070 spi_dv_device(SDp); 2071 } else { 2072 spi_offset(SDp->sdev_target) = 0; 2073 spi_period(SDp->sdev_target) = 0; 2074 } 2075 return 0; 2076 } 2077 2078 STATIC void 2079 NCR_700_slave_destroy(struct scsi_device *SDp) 2080 { 2081 /* to do here: deallocate memory */ 2082 } 2083 2084 static int 2085 NCR_700_change_queue_depth(struct scsi_device *SDp, int depth) 2086 { 2087 if (depth > NCR_700_MAX_TAGS) 2088 depth = NCR_700_MAX_TAGS; 2089 2090 scsi_adjust_queue_depth(SDp, scsi_get_tag_type(SDp), depth); 2091 return depth; 2092 } 2093 2094 static int NCR_700_change_queue_type(struct scsi_device *SDp, int tag_type) 2095 { 2096 int change_tag = ((tag_type ==0 && scsi_get_tag_type(SDp) != 0) 2097 || (tag_type != 0 && scsi_get_tag_type(SDp) == 0)); 2098 struct NCR_700_Host_Parameters *hostdata = 2099 (struct NCR_700_Host_Parameters *)SDp->host->hostdata[0]; 2100 2101 scsi_set_tag_type(SDp, tag_type); 2102 2103 /* We have a global (per target) flag to track whether TCQ is 2104 * enabled, so we'll be turning it off for the entire target here. 2105 * our tag algorithm will fail if we mix tagged and untagged commands, 2106 * so quiesce the device before doing this */ 2107 if (change_tag) 2108 scsi_target_quiesce(SDp->sdev_target); 2109 2110 if (!tag_type) { 2111 /* shift back to the default unqueued number of commands 2112 * (the user can still raise this) */ 2113 scsi_deactivate_tcq(SDp, SDp->host->cmd_per_lun); 2114 hostdata->tag_negotiated &= ~(1 << sdev_id(SDp)); 2115 } else { 2116 /* Here, we cleared the negotiation flag above, so this 2117 * will force the driver to renegotiate */ 2118 scsi_activate_tcq(SDp, SDp->queue_depth); 2119 if (change_tag) 2120 NCR_700_set_tag_neg_state(SDp, NCR_700_START_TAG_NEGOTIATION); 2121 } 2122 if (change_tag) 2123 scsi_target_resume(SDp->sdev_target); 2124 2125 return tag_type; 2126 } 2127 2128 static ssize_t 2129 NCR_700_show_active_tags(struct device *dev, struct device_attribute *attr, char *buf) 2130 { 2131 struct scsi_device *SDp = to_scsi_device(dev); 2132 2133 return snprintf(buf, 20, "%d\n", NCR_700_get_depth(SDp)); 2134 } 2135 2136 static struct device_attribute NCR_700_active_tags_attr = { 2137 .attr = { 2138 .name = "active_tags", 2139 .mode = S_IRUGO, 2140 }, 2141 .show = NCR_700_show_active_tags, 2142 }; 2143 2144 STATIC struct device_attribute *NCR_700_dev_attrs[] = { 2145 &NCR_700_active_tags_attr, 2146 NULL, 2147 }; 2148 2149 EXPORT_SYMBOL(NCR_700_detect); 2150 EXPORT_SYMBOL(NCR_700_release); 2151 EXPORT_SYMBOL(NCR_700_intr); 2152 2153 static struct spi_function_template NCR_700_transport_functions = { 2154 .set_period = NCR_700_set_period, 2155 .show_period = 1, 2156 .set_offset = NCR_700_set_offset, 2157 .show_offset = 1, 2158 }; 2159 2160 static int __init NCR_700_init(void) 2161 { 2162 NCR_700_transport_template = spi_attach_transport(&NCR_700_transport_functions); 2163 if(!NCR_700_transport_template) 2164 return -ENODEV; 2165 return 0; 2166 } 2167 2168 static void __exit NCR_700_exit(void) 2169 { 2170 spi_release_transport(NCR_700_transport_template); 2171 } 2172 2173 module_init(NCR_700_init); 2174 module_exit(NCR_700_exit); 2175 2176