1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * SPI Driver for Microchip MCP795 RTC 4 * 5 * Copyright (C) Josef Gajdusek <atx@atx.name> 6 * 7 * based on other Linux RTC drivers 8 * 9 * Device datasheet: 10 * http://ww1.microchip.com/downloads/en/DeviceDoc/22280A.pdf 11 */ 12 13 #include <linux/module.h> 14 #include <linux/kernel.h> 15 #include <linux/device.h> 16 #include <linux/printk.h> 17 #include <linux/spi/spi.h> 18 #include <linux/rtc.h> 19 #include <linux/of.h> 20 #include <linux/bcd.h> 21 #include <linux/delay.h> 22 23 /* MCP795 Instructions, see datasheet table 3-1 */ 24 #define MCP795_EEREAD 0x03 25 #define MCP795_EEWRITE 0x02 26 #define MCP795_EEWRDI 0x04 27 #define MCP795_EEWREN 0x06 28 #define MCP795_SRREAD 0x05 29 #define MCP795_SRWRITE 0x01 30 #define MCP795_READ 0x13 31 #define MCP795_WRITE 0x12 32 #define MCP795_UNLOCK 0x14 33 #define MCP795_IDWRITE 0x32 34 #define MCP795_IDREAD 0x33 35 #define MCP795_CLRWDT 0x44 36 #define MCP795_CLRRAM 0x54 37 38 /* MCP795 RTCC registers, see datasheet table 4-1 */ 39 #define MCP795_REG_SECONDS 0x01 40 #define MCP795_REG_DAY 0x04 41 #define MCP795_REG_MONTH 0x06 42 #define MCP795_REG_CONTROL 0x08 43 #define MCP795_REG_ALM0_SECONDS 0x0C 44 #define MCP795_REG_ALM0_DAY 0x0F 45 46 #define MCP795_ST_BIT BIT(7) 47 #define MCP795_24_BIT BIT(6) 48 #define MCP795_LP_BIT BIT(5) 49 #define MCP795_EXTOSC_BIT BIT(3) 50 #define MCP795_OSCON_BIT BIT(5) 51 #define MCP795_ALM0_BIT BIT(4) 52 #define MCP795_ALM1_BIT BIT(5) 53 #define MCP795_ALM0IF_BIT BIT(3) 54 #define MCP795_ALM0C0_BIT BIT(4) 55 #define MCP795_ALM0C1_BIT BIT(5) 56 #define MCP795_ALM0C2_BIT BIT(6) 57 58 #define SEC_PER_DAY (24 * 60 * 60) 59 60 static int mcp795_rtcc_read(struct device *dev, u8 addr, u8 *buf, u8 count) 61 { 62 struct spi_device *spi = to_spi_device(dev); 63 int ret; 64 u8 tx[2]; 65 66 tx[0] = MCP795_READ; 67 tx[1] = addr; 68 ret = spi_write_then_read(spi, tx, sizeof(tx), buf, count); 69 70 if (ret) 71 dev_err(dev, "Failed reading %d bytes from address %x.\n", 72 count, addr); 73 74 return ret; 75 } 76 77 static int mcp795_rtcc_write(struct device *dev, u8 addr, u8 *data, u8 count) 78 { 79 struct spi_device *spi = to_spi_device(dev); 80 int ret; 81 u8 tx[257]; 82 83 tx[0] = MCP795_WRITE; 84 tx[1] = addr; 85 memcpy(&tx[2], data, count); 86 87 ret = spi_write(spi, tx, 2 + count); 88 89 if (ret) 90 dev_err(dev, "Failed to write %d bytes to address %x.\n", 91 count, addr); 92 93 return ret; 94 } 95 96 static int mcp795_rtcc_set_bits(struct device *dev, u8 addr, u8 mask, u8 state) 97 { 98 int ret; 99 u8 tmp; 100 101 ret = mcp795_rtcc_read(dev, addr, &tmp, 1); 102 if (ret) 103 return ret; 104 105 if ((tmp & mask) != state) { 106 tmp = (tmp & ~mask) | state; 107 ret = mcp795_rtcc_write(dev, addr, &tmp, 1); 108 } 109 110 return ret; 111 } 112 113 static int mcp795_stop_oscillator(struct device *dev, bool *extosc) 114 { 115 int retries = 5; 116 int ret; 117 u8 data; 118 119 ret = mcp795_rtcc_set_bits(dev, MCP795_REG_SECONDS, MCP795_ST_BIT, 0); 120 if (ret) 121 return ret; 122 ret = mcp795_rtcc_read(dev, MCP795_REG_CONTROL, &data, 1); 123 if (ret) 124 return ret; 125 *extosc = !!(data & MCP795_EXTOSC_BIT); 126 ret = mcp795_rtcc_set_bits( 127 dev, MCP795_REG_CONTROL, MCP795_EXTOSC_BIT, 0); 128 if (ret) 129 return ret; 130 /* wait for the OSCON bit to clear */ 131 do { 132 usleep_range(700, 800); 133 ret = mcp795_rtcc_read(dev, MCP795_REG_DAY, &data, 1); 134 if (ret) 135 break; 136 if (!(data & MCP795_OSCON_BIT)) 137 break; 138 139 } while (--retries); 140 141 return !retries ? -EIO : ret; 142 } 143 144 static int mcp795_start_oscillator(struct device *dev, bool *extosc) 145 { 146 if (extosc) { 147 u8 data = *extosc ? MCP795_EXTOSC_BIT : 0; 148 int ret; 149 150 ret = mcp795_rtcc_set_bits( 151 dev, MCP795_REG_CONTROL, MCP795_EXTOSC_BIT, data); 152 if (ret) 153 return ret; 154 } 155 return mcp795_rtcc_set_bits( 156 dev, MCP795_REG_SECONDS, MCP795_ST_BIT, MCP795_ST_BIT); 157 } 158 159 /* Enable or disable Alarm 0 in RTC */ 160 static int mcp795_update_alarm(struct device *dev, bool enable) 161 { 162 int ret; 163 164 dev_dbg(dev, "%s alarm\n", enable ? "Enable" : "Disable"); 165 166 if (enable) { 167 /* clear ALM0IF (Alarm 0 Interrupt Flag) bit */ 168 ret = mcp795_rtcc_set_bits(dev, MCP795_REG_ALM0_DAY, 169 MCP795_ALM0IF_BIT, 0); 170 if (ret) 171 return ret; 172 /* enable alarm 0 */ 173 ret = mcp795_rtcc_set_bits(dev, MCP795_REG_CONTROL, 174 MCP795_ALM0_BIT, MCP795_ALM0_BIT); 175 } else { 176 /* disable alarm 0 and alarm 1 */ 177 ret = mcp795_rtcc_set_bits(dev, MCP795_REG_CONTROL, 178 MCP795_ALM0_BIT | MCP795_ALM1_BIT, 0); 179 } 180 return ret; 181 } 182 183 static int mcp795_set_time(struct device *dev, struct rtc_time *tim) 184 { 185 int ret; 186 u8 data[7]; 187 bool extosc; 188 189 /* Stop RTC and store current value of EXTOSC bit */ 190 ret = mcp795_stop_oscillator(dev, &extosc); 191 if (ret) 192 return ret; 193 194 /* Read first, so we can leave config bits untouched */ 195 ret = mcp795_rtcc_read(dev, MCP795_REG_SECONDS, data, sizeof(data)); 196 197 if (ret) 198 return ret; 199 200 data[0] = (data[0] & 0x80) | bin2bcd(tim->tm_sec); 201 data[1] = (data[1] & 0x80) | bin2bcd(tim->tm_min); 202 data[2] = bin2bcd(tim->tm_hour); 203 data[3] = (data[3] & 0xF8) | bin2bcd(tim->tm_wday + 1); 204 data[4] = bin2bcd(tim->tm_mday); 205 data[5] = (data[5] & MCP795_LP_BIT) | bin2bcd(tim->tm_mon + 1); 206 207 if (tim->tm_year > 100) 208 tim->tm_year -= 100; 209 210 data[6] = bin2bcd(tim->tm_year); 211 212 /* Always write the date and month using a separate Write command. 213 * This is a workaround for a know silicon issue that some combinations 214 * of date and month values may result in the date being reset to 1. 215 */ 216 ret = mcp795_rtcc_write(dev, MCP795_REG_SECONDS, data, 5); 217 if (ret) 218 return ret; 219 220 ret = mcp795_rtcc_write(dev, MCP795_REG_MONTH, &data[5], 2); 221 if (ret) 222 return ret; 223 224 /* Start back RTC and restore previous value of EXTOSC bit. 225 * There is no need to clear EXTOSC bit when the previous value was 0 226 * because it was already cleared when stopping the RTC oscillator. 227 */ 228 ret = mcp795_start_oscillator(dev, extosc ? &extosc : NULL); 229 if (ret) 230 return ret; 231 232 dev_dbg(dev, "Set mcp795: %ptR\n", tim); 233 234 return 0; 235 } 236 237 static int mcp795_read_time(struct device *dev, struct rtc_time *tim) 238 { 239 int ret; 240 u8 data[7]; 241 242 ret = mcp795_rtcc_read(dev, MCP795_REG_SECONDS, data, sizeof(data)); 243 244 if (ret) 245 return ret; 246 247 tim->tm_sec = bcd2bin(data[0] & 0x7F); 248 tim->tm_min = bcd2bin(data[1] & 0x7F); 249 tim->tm_hour = bcd2bin(data[2] & 0x3F); 250 tim->tm_wday = bcd2bin(data[3] & 0x07) - 1; 251 tim->tm_mday = bcd2bin(data[4] & 0x3F); 252 tim->tm_mon = bcd2bin(data[5] & 0x1F) - 1; 253 tim->tm_year = bcd2bin(data[6]) + 100; /* Assume we are in 20xx */ 254 255 dev_dbg(dev, "Read from mcp795: %ptR\n", tim); 256 257 return 0; 258 } 259 260 static int mcp795_set_alarm(struct device *dev, struct rtc_wkalrm *alm) 261 { 262 struct rtc_time now_tm; 263 time64_t now; 264 time64_t later; 265 u8 tmp[6]; 266 int ret; 267 268 /* Read current time from RTC hardware */ 269 ret = mcp795_read_time(dev, &now_tm); 270 if (ret) 271 return ret; 272 /* Get the number of seconds since 1970 */ 273 now = rtc_tm_to_time64(&now_tm); 274 later = rtc_tm_to_time64(&alm->time); 275 if (later <= now) 276 return -EINVAL; 277 /* make sure alarm fires within the next one year */ 278 if ((later - now) >= 279 (SEC_PER_DAY * (365 + is_leap_year(alm->time.tm_year)))) 280 return -EDOM; 281 /* disable alarm */ 282 ret = mcp795_update_alarm(dev, false); 283 if (ret) 284 return ret; 285 /* Read registers, so we can leave configuration bits untouched */ 286 ret = mcp795_rtcc_read(dev, MCP795_REG_ALM0_SECONDS, tmp, sizeof(tmp)); 287 if (ret) 288 return ret; 289 290 alm->time.tm_year = -1; 291 alm->time.tm_isdst = -1; 292 alm->time.tm_yday = -1; 293 294 tmp[0] = (tmp[0] & 0x80) | bin2bcd(alm->time.tm_sec); 295 tmp[1] = (tmp[1] & 0x80) | bin2bcd(alm->time.tm_min); 296 tmp[2] = (tmp[2] & 0xE0) | bin2bcd(alm->time.tm_hour); 297 tmp[3] = (tmp[3] & 0x80) | bin2bcd(alm->time.tm_wday + 1); 298 /* set alarm match: seconds, minutes, hour, day, date and month */ 299 tmp[3] |= (MCP795_ALM0C2_BIT | MCP795_ALM0C1_BIT | MCP795_ALM0C0_BIT); 300 tmp[4] = (tmp[4] & 0xC0) | bin2bcd(alm->time.tm_mday); 301 tmp[5] = (tmp[5] & 0xE0) | bin2bcd(alm->time.tm_mon + 1); 302 303 ret = mcp795_rtcc_write(dev, MCP795_REG_ALM0_SECONDS, tmp, sizeof(tmp)); 304 if (ret) 305 return ret; 306 307 /* enable alarm if requested */ 308 if (alm->enabled) { 309 ret = mcp795_update_alarm(dev, true); 310 if (ret) 311 return ret; 312 dev_dbg(dev, "Alarm IRQ armed\n"); 313 } 314 dev_dbg(dev, "Set alarm: %ptRdr(%d) %ptRt\n", 315 &alm->time, alm->time.tm_wday, &alm->time); 316 return 0; 317 } 318 319 static int mcp795_read_alarm(struct device *dev, struct rtc_wkalrm *alm) 320 { 321 u8 data[6]; 322 int ret; 323 324 ret = mcp795_rtcc_read( 325 dev, MCP795_REG_ALM0_SECONDS, data, sizeof(data)); 326 if (ret) 327 return ret; 328 329 alm->time.tm_sec = bcd2bin(data[0] & 0x7F); 330 alm->time.tm_min = bcd2bin(data[1] & 0x7F); 331 alm->time.tm_hour = bcd2bin(data[2] & 0x1F); 332 alm->time.tm_wday = bcd2bin(data[3] & 0x07) - 1; 333 alm->time.tm_mday = bcd2bin(data[4] & 0x3F); 334 alm->time.tm_mon = bcd2bin(data[5] & 0x1F) - 1; 335 alm->time.tm_year = -1; 336 alm->time.tm_isdst = -1; 337 alm->time.tm_yday = -1; 338 339 dev_dbg(dev, "Read alarm: %ptRdr(%d) %ptRt\n", 340 &alm->time, alm->time.tm_wday, &alm->time); 341 return 0; 342 } 343 344 static int mcp795_alarm_irq_enable(struct device *dev, unsigned int enabled) 345 { 346 return mcp795_update_alarm(dev, !!enabled); 347 } 348 349 static irqreturn_t mcp795_irq(int irq, void *data) 350 { 351 struct spi_device *spi = data; 352 struct rtc_device *rtc = spi_get_drvdata(spi); 353 struct mutex *lock = &rtc->ops_lock; 354 int ret; 355 356 mutex_lock(lock); 357 358 /* Disable alarm. 359 * There is no need to clear ALM0IF (Alarm 0 Interrupt Flag) bit, 360 * because it is done every time when alarm is enabled. 361 */ 362 ret = mcp795_update_alarm(&spi->dev, false); 363 if (ret) 364 dev_err(&spi->dev, 365 "Failed to disable alarm in IRQ (ret=%d)\n", ret); 366 rtc_update_irq(rtc, 1, RTC_AF | RTC_IRQF); 367 368 mutex_unlock(lock); 369 370 return IRQ_HANDLED; 371 } 372 373 static const struct rtc_class_ops mcp795_rtc_ops = { 374 .read_time = mcp795_read_time, 375 .set_time = mcp795_set_time, 376 .read_alarm = mcp795_read_alarm, 377 .set_alarm = mcp795_set_alarm, 378 .alarm_irq_enable = mcp795_alarm_irq_enable 379 }; 380 381 static int mcp795_probe(struct spi_device *spi) 382 { 383 struct rtc_device *rtc; 384 int ret; 385 386 spi->mode = SPI_MODE_0; 387 spi->bits_per_word = 8; 388 ret = spi_setup(spi); 389 if (ret) { 390 dev_err(&spi->dev, "Unable to setup SPI\n"); 391 return ret; 392 } 393 394 /* Start the oscillator but don't set the value of EXTOSC bit */ 395 mcp795_start_oscillator(&spi->dev, NULL); 396 /* Clear the 12 hour mode flag*/ 397 mcp795_rtcc_set_bits(&spi->dev, 0x03, MCP795_24_BIT, 0); 398 399 rtc = devm_rtc_device_register(&spi->dev, "rtc-mcp795", 400 &mcp795_rtc_ops, THIS_MODULE); 401 if (IS_ERR(rtc)) 402 return PTR_ERR(rtc); 403 404 spi_set_drvdata(spi, rtc); 405 406 if (spi->irq > 0) { 407 dev_dbg(&spi->dev, "Alarm support enabled\n"); 408 409 /* Clear any pending alarm (ALM0IF bit) before requesting 410 * the interrupt. 411 */ 412 mcp795_rtcc_set_bits(&spi->dev, MCP795_REG_ALM0_DAY, 413 MCP795_ALM0IF_BIT, 0); 414 ret = devm_request_threaded_irq(&spi->dev, spi->irq, NULL, 415 mcp795_irq, IRQF_TRIGGER_FALLING | IRQF_ONESHOT, 416 dev_name(&rtc->dev), spi); 417 if (ret) 418 dev_err(&spi->dev, "Failed to request IRQ: %d: %d\n", 419 spi->irq, ret); 420 else 421 device_init_wakeup(&spi->dev, true); 422 } 423 return 0; 424 } 425 426 #ifdef CONFIG_OF 427 static const struct of_device_id mcp795_of_match[] = { 428 { .compatible = "maxim,mcp795" }, 429 { } 430 }; 431 MODULE_DEVICE_TABLE(of, mcp795_of_match); 432 #endif 433 434 static struct spi_driver mcp795_driver = { 435 .driver = { 436 .name = "rtc-mcp795", 437 .of_match_table = of_match_ptr(mcp795_of_match), 438 }, 439 .probe = mcp795_probe, 440 }; 441 442 module_spi_driver(mcp795_driver); 443 444 MODULE_DESCRIPTION("MCP795 RTC SPI Driver"); 445 MODULE_AUTHOR("Josef Gajdusek <atx@atx.name>"); 446 MODULE_LICENSE("GPL"); 447 MODULE_ALIAS("spi:mcp795"); 448