1 /* 2 * Copyright 2008-2009 Freescale Semiconductor, Inc. All Rights Reserved. 3 * Copyright 2010 Orex Computed Radiography 4 */ 5 6 /* 7 * The code contained herein is licensed under the GNU General Public 8 * License. You may obtain a copy of the GNU General Public License 9 * Version 2 or later at the following locations: 10 * 11 * http://www.opensource.org/licenses/gpl-license.html 12 * http://www.gnu.org/copyleft/gpl.html 13 */ 14 15 /* based on rtc-mc13892.c */ 16 17 /* 18 * This driver uses the 47-bit 32 kHz counter in the Freescale DryIce block 19 * to implement a Linux RTC. Times and alarms are truncated to seconds. 20 * Since the RTC framework performs API locking via rtc->ops_lock the 21 * only simultaneous accesses we need to deal with is updating DryIce 22 * registers while servicing an alarm. 23 * 24 * Note that reading the DSR (DryIce Status Register) automatically clears 25 * the WCF (Write Complete Flag). All DryIce writes are synchronized to the 26 * LP (Low Power) domain and set the WCF upon completion. Writes to the 27 * DIER (DryIce Interrupt Enable Register) are the only exception. These 28 * occur at normal bus speeds and do not set WCF. Periodic interrupts are 29 * not supported by the hardware. 30 */ 31 32 #include <linux/io.h> 33 #include <linux/clk.h> 34 #include <linux/delay.h> 35 #include <linux/module.h> 36 #include <linux/platform_device.h> 37 #include <linux/rtc.h> 38 #include <linux/sched.h> 39 #include <linux/spinlock.h> 40 #include <linux/workqueue.h> 41 #include <linux/of.h> 42 43 /* DryIce Register Definitions */ 44 45 #define DTCMR 0x00 /* Time Counter MSB Reg */ 46 #define DTCLR 0x04 /* Time Counter LSB Reg */ 47 48 #define DCAMR 0x08 /* Clock Alarm MSB Reg */ 49 #define DCALR 0x0c /* Clock Alarm LSB Reg */ 50 #define DCAMR_UNSET 0xFFFFFFFF /* doomsday - 1 sec */ 51 52 #define DCR 0x10 /* Control Reg */ 53 #define DCR_TDCHL (1 << 30) /* Tamper-detect configuration hard lock */ 54 #define DCR_TDCSL (1 << 29) /* Tamper-detect configuration soft lock */ 55 #define DCR_KSSL (1 << 27) /* Key-select soft lock */ 56 #define DCR_MCHL (1 << 20) /* Monotonic-counter hard lock */ 57 #define DCR_MCSL (1 << 19) /* Monotonic-counter soft lock */ 58 #define DCR_TCHL (1 << 18) /* Timer-counter hard lock */ 59 #define DCR_TCSL (1 << 17) /* Timer-counter soft lock */ 60 #define DCR_FSHL (1 << 16) /* Failure state hard lock */ 61 #define DCR_TCE (1 << 3) /* Time Counter Enable */ 62 #define DCR_MCE (1 << 2) /* Monotonic Counter Enable */ 63 64 #define DSR 0x14 /* Status Reg */ 65 #define DSR_WTD (1 << 23) /* Wire-mesh tamper detected */ 66 #define DSR_ETBD (1 << 22) /* External tamper B detected */ 67 #define DSR_ETAD (1 << 21) /* External tamper A detected */ 68 #define DSR_EBD (1 << 20) /* External boot detected */ 69 #define DSR_SAD (1 << 19) /* SCC alarm detected */ 70 #define DSR_TTD (1 << 18) /* Temperature tamper detected */ 71 #define DSR_CTD (1 << 17) /* Clock tamper detected */ 72 #define DSR_VTD (1 << 16) /* Voltage tamper detected */ 73 #define DSR_WBF (1 << 10) /* Write Busy Flag (synchronous) */ 74 #define DSR_WNF (1 << 9) /* Write Next Flag (synchronous) */ 75 #define DSR_WCF (1 << 8) /* Write Complete Flag (synchronous)*/ 76 #define DSR_WEF (1 << 7) /* Write Error Flag */ 77 #define DSR_CAF (1 << 4) /* Clock Alarm Flag */ 78 #define DSR_MCO (1 << 3) /* monotonic counter overflow */ 79 #define DSR_TCO (1 << 2) /* time counter overflow */ 80 #define DSR_NVF (1 << 1) /* Non-Valid Flag */ 81 #define DSR_SVF (1 << 0) /* Security Violation Flag */ 82 83 #define DIER 0x18 /* Interrupt Enable Reg (synchronous) */ 84 #define DIER_WNIE (1 << 9) /* Write Next Interrupt Enable */ 85 #define DIER_WCIE (1 << 8) /* Write Complete Interrupt Enable */ 86 #define DIER_WEIE (1 << 7) /* Write Error Interrupt Enable */ 87 #define DIER_CAIE (1 << 4) /* Clock Alarm Interrupt Enable */ 88 #define DIER_SVIE (1 << 0) /* Security-violation Interrupt Enable */ 89 90 #define DMCR 0x1c /* DryIce Monotonic Counter Reg */ 91 92 #define DTCR 0x28 /* DryIce Tamper Configuration Reg */ 93 #define DTCR_MOE (1 << 9) /* monotonic overflow enabled */ 94 #define DTCR_TOE (1 << 8) /* time overflow enabled */ 95 #define DTCR_WTE (1 << 7) /* wire-mesh tamper enabled */ 96 #define DTCR_ETBE (1 << 6) /* external B tamper enabled */ 97 #define DTCR_ETAE (1 << 5) /* external A tamper enabled */ 98 #define DTCR_EBE (1 << 4) /* external boot tamper enabled */ 99 #define DTCR_SAIE (1 << 3) /* SCC enabled */ 100 #define DTCR_TTE (1 << 2) /* temperature tamper enabled */ 101 #define DTCR_CTE (1 << 1) /* clock tamper enabled */ 102 #define DTCR_VTE (1 << 0) /* voltage tamper enabled */ 103 104 #define DGPR 0x3c /* DryIce General Purpose Reg */ 105 106 /** 107 * struct imxdi_dev - private imxdi rtc data 108 * @pdev: pionter to platform dev 109 * @rtc: pointer to rtc struct 110 * @ioaddr: IO registers pointer 111 * @clk: input reference clock 112 * @dsr: copy of the DSR register 113 * @irq_lock: interrupt enable register (DIER) lock 114 * @write_wait: registers write complete queue 115 * @write_mutex: serialize registers write 116 * @work: schedule alarm work 117 */ 118 struct imxdi_dev { 119 struct platform_device *pdev; 120 struct rtc_device *rtc; 121 void __iomem *ioaddr; 122 struct clk *clk; 123 u32 dsr; 124 spinlock_t irq_lock; 125 wait_queue_head_t write_wait; 126 struct mutex write_mutex; 127 struct work_struct work; 128 }; 129 130 /* Some background: 131 * 132 * The DryIce unit is a complex security/tamper monitor device. To be able do 133 * its job in a useful manner it runs a bigger statemachine to bring it into 134 * security/tamper failure state and once again to bring it out of this state. 135 * 136 * This unit can be in one of three states: 137 * 138 * - "NON-VALID STATE" 139 * always after the battery power was removed 140 * - "FAILURE STATE" 141 * if one of the enabled security events has happened 142 * - "VALID STATE" 143 * if the unit works as expected 144 * 145 * Everything stops when the unit enters the failure state including the RTC 146 * counter (to be able to detect the time the security event happened). 147 * 148 * The following events (when enabled) let the DryIce unit enter the failure 149 * state: 150 * 151 * - wire-mesh-tamper detect 152 * - external tamper B detect 153 * - external tamper A detect 154 * - temperature tamper detect 155 * - clock tamper detect 156 * - voltage tamper detect 157 * - RTC counter overflow 158 * - monotonic counter overflow 159 * - external boot 160 * 161 * If we find the DryIce unit in "FAILURE STATE" and the TDCHL cleared, we 162 * can only detect this state. In this case the unit is completely locked and 163 * must force a second "SYSTEM POR" to bring the DryIce into the 164 * "NON-VALID STATE" + "FAILURE STATE" where a recovery is possible. 165 * If the TDCHL is set in the "FAILURE STATE" we are out of luck. In this case 166 * a battery power cycle is required. 167 * 168 * In the "NON-VALID STATE" + "FAILURE STATE" we can clear the "FAILURE STATE" 169 * and recover the DryIce unit. By clearing the "NON-VALID STATE" as the last 170 * task, we bring back this unit into life. 171 */ 172 173 /* 174 * Do a write into the unit without interrupt support. 175 * We do not need to check the WEF here, because the only reason this kind of 176 * write error can happen is if we write to the unit twice within the 122 us 177 * interval. This cannot happen, since we are using this function only while 178 * setting up the unit. 179 */ 180 static void di_write_busy_wait(const struct imxdi_dev *imxdi, u32 val, 181 unsigned reg) 182 { 183 /* do the register write */ 184 writel(val, imxdi->ioaddr + reg); 185 186 /* 187 * now it takes four 32,768 kHz clock cycles to take 188 * the change into effect = 122 us 189 */ 190 usleep_range(130, 200); 191 } 192 193 static void di_report_tamper_info(struct imxdi_dev *imxdi, u32 dsr) 194 { 195 u32 dtcr; 196 197 dtcr = readl(imxdi->ioaddr + DTCR); 198 199 dev_emerg(&imxdi->pdev->dev, "DryIce tamper event detected\n"); 200 /* the following flags force a transition into the "FAILURE STATE" */ 201 if (dsr & DSR_VTD) 202 dev_emerg(&imxdi->pdev->dev, "%sVoltage Tamper Event\n", 203 dtcr & DTCR_VTE ? "" : "Spurious "); 204 205 if (dsr & DSR_CTD) 206 dev_emerg(&imxdi->pdev->dev, "%s32768 Hz Clock Tamper Event\n", 207 dtcr & DTCR_CTE ? "" : "Spurious "); 208 209 if (dsr & DSR_TTD) 210 dev_emerg(&imxdi->pdev->dev, "%sTemperature Tamper Event\n", 211 dtcr & DTCR_TTE ? "" : "Spurious "); 212 213 if (dsr & DSR_SAD) 214 dev_emerg(&imxdi->pdev->dev, 215 "%sSecure Controller Alarm Event\n", 216 dtcr & DTCR_SAIE ? "" : "Spurious "); 217 218 if (dsr & DSR_EBD) 219 dev_emerg(&imxdi->pdev->dev, "%sExternal Boot Tamper Event\n", 220 dtcr & DTCR_EBE ? "" : "Spurious "); 221 222 if (dsr & DSR_ETAD) 223 dev_emerg(&imxdi->pdev->dev, "%sExternal Tamper A Event\n", 224 dtcr & DTCR_ETAE ? "" : "Spurious "); 225 226 if (dsr & DSR_ETBD) 227 dev_emerg(&imxdi->pdev->dev, "%sExternal Tamper B Event\n", 228 dtcr & DTCR_ETBE ? "" : "Spurious "); 229 230 if (dsr & DSR_WTD) 231 dev_emerg(&imxdi->pdev->dev, "%sWire-mesh Tamper Event\n", 232 dtcr & DTCR_WTE ? "" : "Spurious "); 233 234 if (dsr & DSR_MCO) 235 dev_emerg(&imxdi->pdev->dev, 236 "%sMonotonic-counter Overflow Event\n", 237 dtcr & DTCR_MOE ? "" : "Spurious "); 238 239 if (dsr & DSR_TCO) 240 dev_emerg(&imxdi->pdev->dev, "%sTimer-counter Overflow Event\n", 241 dtcr & DTCR_TOE ? "" : "Spurious "); 242 } 243 244 static void di_what_is_to_be_done(struct imxdi_dev *imxdi, 245 const char *power_supply) 246 { 247 dev_emerg(&imxdi->pdev->dev, "Please cycle the %s power supply in order to get the DryIce/RTC unit working again\n", 248 power_supply); 249 } 250 251 static int di_handle_failure_state(struct imxdi_dev *imxdi, u32 dsr) 252 { 253 u32 dcr; 254 255 dev_dbg(&imxdi->pdev->dev, "DSR register reports: %08X\n", dsr); 256 257 /* report the cause */ 258 di_report_tamper_info(imxdi, dsr); 259 260 dcr = readl(imxdi->ioaddr + DCR); 261 262 if (dcr & DCR_FSHL) { 263 /* we are out of luck */ 264 di_what_is_to_be_done(imxdi, "battery"); 265 return -ENODEV; 266 } 267 /* 268 * with the next SYSTEM POR we will transit from the "FAILURE STATE" 269 * into the "NON-VALID STATE" + "FAILURE STATE" 270 */ 271 di_what_is_to_be_done(imxdi, "main"); 272 273 return -ENODEV; 274 } 275 276 static int di_handle_valid_state(struct imxdi_dev *imxdi, u32 dsr) 277 { 278 /* initialize alarm */ 279 di_write_busy_wait(imxdi, DCAMR_UNSET, DCAMR); 280 di_write_busy_wait(imxdi, 0, DCALR); 281 282 /* clear alarm flag */ 283 if (dsr & DSR_CAF) 284 di_write_busy_wait(imxdi, DSR_CAF, DSR); 285 286 return 0; 287 } 288 289 static int di_handle_invalid_state(struct imxdi_dev *imxdi, u32 dsr) 290 { 291 u32 dcr, sec; 292 293 /* 294 * lets disable all sources which can force the DryIce unit into 295 * the "FAILURE STATE" for now 296 */ 297 di_write_busy_wait(imxdi, 0x00000000, DTCR); 298 /* and lets protect them at runtime from any change */ 299 di_write_busy_wait(imxdi, DCR_TDCSL, DCR); 300 301 sec = readl(imxdi->ioaddr + DTCMR); 302 if (sec != 0) 303 dev_warn(&imxdi->pdev->dev, 304 "The security violation has happened at %u seconds\n", 305 sec); 306 /* 307 * the timer cannot be set/modified if 308 * - the TCHL or TCSL bit is set in DCR 309 */ 310 dcr = readl(imxdi->ioaddr + DCR); 311 if (!(dcr & DCR_TCE)) { 312 if (dcr & DCR_TCHL) { 313 /* we are out of luck */ 314 di_what_is_to_be_done(imxdi, "battery"); 315 return -ENODEV; 316 } 317 if (dcr & DCR_TCSL) { 318 di_what_is_to_be_done(imxdi, "main"); 319 return -ENODEV; 320 } 321 } 322 /* 323 * - the timer counter stops/is stopped if 324 * - its overflow flag is set (TCO in DSR) 325 * -> clear overflow bit to make it count again 326 * - NVF is set in DSR 327 * -> clear non-valid bit to make it count again 328 * - its TCE (DCR) is cleared 329 * -> set TCE to make it count 330 * - it was never set before 331 * -> write a time into it (required again if the NVF was set) 332 */ 333 /* state handled */ 334 di_write_busy_wait(imxdi, DSR_NVF, DSR); 335 /* clear overflow flag */ 336 di_write_busy_wait(imxdi, DSR_TCO, DSR); 337 /* enable the counter */ 338 di_write_busy_wait(imxdi, dcr | DCR_TCE, DCR); 339 /* set and trigger it to make it count */ 340 di_write_busy_wait(imxdi, sec, DTCMR); 341 342 /* now prepare for the valid state */ 343 return di_handle_valid_state(imxdi, __raw_readl(imxdi->ioaddr + DSR)); 344 } 345 346 static int di_handle_invalid_and_failure_state(struct imxdi_dev *imxdi, u32 dsr) 347 { 348 u32 dcr; 349 350 /* 351 * now we must first remove the tamper sources in order to get the 352 * device out of the "FAILURE STATE" 353 * To disable any of the following sources we need to modify the DTCR 354 */ 355 if (dsr & (DSR_WTD | DSR_ETBD | DSR_ETAD | DSR_EBD | DSR_SAD | 356 DSR_TTD | DSR_CTD | DSR_VTD | DSR_MCO | DSR_TCO)) { 357 dcr = __raw_readl(imxdi->ioaddr + DCR); 358 if (dcr & DCR_TDCHL) { 359 /* 360 * the tamper register is locked. We cannot disable the 361 * tamper detection. The TDCHL can only be reset by a 362 * DRYICE POR, but we cannot force a DRYICE POR in 363 * softwere because we are still in "FAILURE STATE". 364 * We need a DRYICE POR via battery power cycling.... 365 */ 366 /* 367 * out of luck! 368 * we cannot disable them without a DRYICE POR 369 */ 370 di_what_is_to_be_done(imxdi, "battery"); 371 return -ENODEV; 372 } 373 if (dcr & DCR_TDCSL) { 374 /* a soft lock can be removed by a SYSTEM POR */ 375 di_what_is_to_be_done(imxdi, "main"); 376 return -ENODEV; 377 } 378 } 379 380 /* disable all sources */ 381 di_write_busy_wait(imxdi, 0x00000000, DTCR); 382 383 /* clear the status bits now */ 384 di_write_busy_wait(imxdi, dsr & (DSR_WTD | DSR_ETBD | DSR_ETAD | 385 DSR_EBD | DSR_SAD | DSR_TTD | DSR_CTD | DSR_VTD | 386 DSR_MCO | DSR_TCO), DSR); 387 388 dsr = readl(imxdi->ioaddr + DSR); 389 if ((dsr & ~(DSR_NVF | DSR_SVF | DSR_WBF | DSR_WNF | 390 DSR_WCF | DSR_WEF)) != 0) 391 dev_warn(&imxdi->pdev->dev, 392 "There are still some sources of pain in DSR: %08x!\n", 393 dsr & ~(DSR_NVF | DSR_SVF | DSR_WBF | DSR_WNF | 394 DSR_WCF | DSR_WEF)); 395 396 /* 397 * now we are trying to clear the "Security-violation flag" to 398 * get the DryIce out of this state 399 */ 400 di_write_busy_wait(imxdi, DSR_SVF, DSR); 401 402 /* success? */ 403 dsr = readl(imxdi->ioaddr + DSR); 404 if (dsr & DSR_SVF) { 405 dev_crit(&imxdi->pdev->dev, 406 "Cannot clear the security violation flag. We are ending up in an endless loop!\n"); 407 /* last resort */ 408 di_what_is_to_be_done(imxdi, "battery"); 409 return -ENODEV; 410 } 411 412 /* 413 * now we have left the "FAILURE STATE" and ending up in the 414 * "NON-VALID STATE" time to recover everything 415 */ 416 return di_handle_invalid_state(imxdi, dsr); 417 } 418 419 static int di_handle_state(struct imxdi_dev *imxdi) 420 { 421 int rc; 422 u32 dsr; 423 424 dsr = readl(imxdi->ioaddr + DSR); 425 426 switch (dsr & (DSR_NVF | DSR_SVF)) { 427 case DSR_NVF: 428 dev_warn(&imxdi->pdev->dev, "Invalid stated unit detected\n"); 429 rc = di_handle_invalid_state(imxdi, dsr); 430 break; 431 case DSR_SVF: 432 dev_warn(&imxdi->pdev->dev, "Failure stated unit detected\n"); 433 rc = di_handle_failure_state(imxdi, dsr); 434 break; 435 case DSR_NVF | DSR_SVF: 436 dev_warn(&imxdi->pdev->dev, 437 "Failure+Invalid stated unit detected\n"); 438 rc = di_handle_invalid_and_failure_state(imxdi, dsr); 439 break; 440 default: 441 dev_notice(&imxdi->pdev->dev, "Unlocked unit detected\n"); 442 rc = di_handle_valid_state(imxdi, dsr); 443 } 444 445 return rc; 446 } 447 448 /* 449 * enable a dryice interrupt 450 */ 451 static void di_int_enable(struct imxdi_dev *imxdi, u32 intr) 452 { 453 unsigned long flags; 454 455 spin_lock_irqsave(&imxdi->irq_lock, flags); 456 writel(readl(imxdi->ioaddr + DIER) | intr, 457 imxdi->ioaddr + DIER); 458 spin_unlock_irqrestore(&imxdi->irq_lock, flags); 459 } 460 461 /* 462 * disable a dryice interrupt 463 */ 464 static void di_int_disable(struct imxdi_dev *imxdi, u32 intr) 465 { 466 unsigned long flags; 467 468 spin_lock_irqsave(&imxdi->irq_lock, flags); 469 writel(readl(imxdi->ioaddr + DIER) & ~intr, 470 imxdi->ioaddr + DIER); 471 spin_unlock_irqrestore(&imxdi->irq_lock, flags); 472 } 473 474 /* 475 * This function attempts to clear the dryice write-error flag. 476 * 477 * A dryice write error is similar to a bus fault and should not occur in 478 * normal operation. Clearing the flag requires another write, so the root 479 * cause of the problem may need to be fixed before the flag can be cleared. 480 */ 481 static void clear_write_error(struct imxdi_dev *imxdi) 482 { 483 int cnt; 484 485 dev_warn(&imxdi->pdev->dev, "WARNING: Register write error!\n"); 486 487 /* clear the write error flag */ 488 writel(DSR_WEF, imxdi->ioaddr + DSR); 489 490 /* wait for it to take effect */ 491 for (cnt = 0; cnt < 1000; cnt++) { 492 if ((readl(imxdi->ioaddr + DSR) & DSR_WEF) == 0) 493 return; 494 udelay(10); 495 } 496 dev_err(&imxdi->pdev->dev, 497 "ERROR: Cannot clear write-error flag!\n"); 498 } 499 500 /* 501 * Write a dryice register and wait until it completes. 502 * 503 * This function uses interrupts to determine when the 504 * write has completed. 505 */ 506 static int di_write_wait(struct imxdi_dev *imxdi, u32 val, int reg) 507 { 508 int ret; 509 int rc = 0; 510 511 /* serialize register writes */ 512 mutex_lock(&imxdi->write_mutex); 513 514 /* enable the write-complete interrupt */ 515 di_int_enable(imxdi, DIER_WCIE); 516 517 imxdi->dsr = 0; 518 519 /* do the register write */ 520 writel(val, imxdi->ioaddr + reg); 521 522 /* wait for the write to finish */ 523 ret = wait_event_interruptible_timeout(imxdi->write_wait, 524 imxdi->dsr & (DSR_WCF | DSR_WEF), msecs_to_jiffies(1)); 525 if (ret < 0) { 526 rc = ret; 527 goto out; 528 } else if (ret == 0) { 529 dev_warn(&imxdi->pdev->dev, 530 "Write-wait timeout " 531 "val = 0x%08x reg = 0x%08x\n", val, reg); 532 } 533 534 /* check for write error */ 535 if (imxdi->dsr & DSR_WEF) { 536 clear_write_error(imxdi); 537 rc = -EIO; 538 } 539 540 out: 541 mutex_unlock(&imxdi->write_mutex); 542 543 return rc; 544 } 545 546 /* 547 * read the seconds portion of the current time from the dryice time counter 548 */ 549 static int dryice_rtc_read_time(struct device *dev, struct rtc_time *tm) 550 { 551 struct imxdi_dev *imxdi = dev_get_drvdata(dev); 552 unsigned long now; 553 554 now = readl(imxdi->ioaddr + DTCMR); 555 rtc_time_to_tm(now, tm); 556 557 return 0; 558 } 559 560 /* 561 * set the seconds portion of dryice time counter and clear the 562 * fractional part. 563 */ 564 static int dryice_rtc_set_mmss(struct device *dev, unsigned long secs) 565 { 566 struct imxdi_dev *imxdi = dev_get_drvdata(dev); 567 u32 dcr, dsr; 568 int rc; 569 570 dcr = readl(imxdi->ioaddr + DCR); 571 dsr = readl(imxdi->ioaddr + DSR); 572 573 if (!(dcr & DCR_TCE) || (dsr & DSR_SVF)) { 574 if (dcr & DCR_TCHL) { 575 /* we are even more out of luck */ 576 di_what_is_to_be_done(imxdi, "battery"); 577 return -EPERM; 578 } 579 if ((dcr & DCR_TCSL) || (dsr & DSR_SVF)) { 580 /* we are out of luck for now */ 581 di_what_is_to_be_done(imxdi, "main"); 582 return -EPERM; 583 } 584 } 585 586 /* zero the fractional part first */ 587 rc = di_write_wait(imxdi, 0, DTCLR); 588 if (rc != 0) 589 return rc; 590 591 rc = di_write_wait(imxdi, secs, DTCMR); 592 if (rc != 0) 593 return rc; 594 595 return di_write_wait(imxdi, readl(imxdi->ioaddr + DCR) | DCR_TCE, DCR); 596 } 597 598 static int dryice_rtc_alarm_irq_enable(struct device *dev, 599 unsigned int enabled) 600 { 601 struct imxdi_dev *imxdi = dev_get_drvdata(dev); 602 603 if (enabled) 604 di_int_enable(imxdi, DIER_CAIE); 605 else 606 di_int_disable(imxdi, DIER_CAIE); 607 608 return 0; 609 } 610 611 /* 612 * read the seconds portion of the alarm register. 613 * the fractional part of the alarm register is always zero. 614 */ 615 static int dryice_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alarm) 616 { 617 struct imxdi_dev *imxdi = dev_get_drvdata(dev); 618 u32 dcamr; 619 620 dcamr = readl(imxdi->ioaddr + DCAMR); 621 rtc_time_to_tm(dcamr, &alarm->time); 622 623 /* alarm is enabled if the interrupt is enabled */ 624 alarm->enabled = (readl(imxdi->ioaddr + DIER) & DIER_CAIE) != 0; 625 626 /* don't allow the DSR read to mess up DSR_WCF */ 627 mutex_lock(&imxdi->write_mutex); 628 629 /* alarm is pending if the alarm flag is set */ 630 alarm->pending = (readl(imxdi->ioaddr + DSR) & DSR_CAF) != 0; 631 632 mutex_unlock(&imxdi->write_mutex); 633 634 return 0; 635 } 636 637 /* 638 * set the seconds portion of dryice alarm register 639 */ 640 static int dryice_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alarm) 641 { 642 struct imxdi_dev *imxdi = dev_get_drvdata(dev); 643 unsigned long now; 644 unsigned long alarm_time; 645 int rc; 646 647 rc = rtc_tm_to_time(&alarm->time, &alarm_time); 648 if (rc) 649 return rc; 650 651 /* don't allow setting alarm in the past */ 652 now = readl(imxdi->ioaddr + DTCMR); 653 if (alarm_time < now) 654 return -EINVAL; 655 656 /* write the new alarm time */ 657 rc = di_write_wait(imxdi, (u32)alarm_time, DCAMR); 658 if (rc) 659 return rc; 660 661 if (alarm->enabled) 662 di_int_enable(imxdi, DIER_CAIE); /* enable alarm intr */ 663 else 664 di_int_disable(imxdi, DIER_CAIE); /* disable alarm intr */ 665 666 return 0; 667 } 668 669 static const struct rtc_class_ops dryice_rtc_ops = { 670 .read_time = dryice_rtc_read_time, 671 .set_mmss = dryice_rtc_set_mmss, 672 .alarm_irq_enable = dryice_rtc_alarm_irq_enable, 673 .read_alarm = dryice_rtc_read_alarm, 674 .set_alarm = dryice_rtc_set_alarm, 675 }; 676 677 /* 678 * interrupt handler for dryice "normal" and security violation interrupt 679 */ 680 static irqreturn_t dryice_irq(int irq, void *dev_id) 681 { 682 struct imxdi_dev *imxdi = dev_id; 683 u32 dsr, dier; 684 irqreturn_t rc = IRQ_NONE; 685 686 dier = readl(imxdi->ioaddr + DIER); 687 dsr = readl(imxdi->ioaddr + DSR); 688 689 /* handle the security violation event */ 690 if (dier & DIER_SVIE) { 691 if (dsr & DSR_SVF) { 692 /* 693 * Disable the interrupt when this kind of event has 694 * happened. 695 * There cannot be more than one event of this type, 696 * because it needs a complex state change 697 * including a main power cycle to get again out of 698 * this state. 699 */ 700 di_int_disable(imxdi, DIER_SVIE); 701 /* report the violation */ 702 di_report_tamper_info(imxdi, dsr); 703 rc = IRQ_HANDLED; 704 } 705 } 706 707 /* handle write complete and write error cases */ 708 if (dier & DIER_WCIE) { 709 /*If the write wait queue is empty then there is no pending 710 operations. It means the interrupt is for DryIce -Security. 711 IRQ must be returned as none.*/ 712 if (list_empty_careful(&imxdi->write_wait.head)) 713 return rc; 714 715 /* DSR_WCF clears itself on DSR read */ 716 if (dsr & (DSR_WCF | DSR_WEF)) { 717 /* mask the interrupt */ 718 di_int_disable(imxdi, DIER_WCIE); 719 720 /* save the dsr value for the wait queue */ 721 imxdi->dsr |= dsr; 722 723 wake_up_interruptible(&imxdi->write_wait); 724 rc = IRQ_HANDLED; 725 } 726 } 727 728 /* handle the alarm case */ 729 if (dier & DIER_CAIE) { 730 /* DSR_WCF clears itself on DSR read */ 731 if (dsr & DSR_CAF) { 732 /* mask the interrupt */ 733 di_int_disable(imxdi, DIER_CAIE); 734 735 /* finish alarm in user context */ 736 schedule_work(&imxdi->work); 737 rc = IRQ_HANDLED; 738 } 739 } 740 return rc; 741 } 742 743 /* 744 * post the alarm event from user context so it can sleep 745 * on the write completion. 746 */ 747 static void dryice_work(struct work_struct *work) 748 { 749 struct imxdi_dev *imxdi = container_of(work, 750 struct imxdi_dev, work); 751 752 /* dismiss the interrupt (ignore error) */ 753 di_write_wait(imxdi, DSR_CAF, DSR); 754 755 /* pass the alarm event to the rtc framework. */ 756 rtc_update_irq(imxdi->rtc, 1, RTC_AF | RTC_IRQF); 757 } 758 759 /* 760 * probe for dryice rtc device 761 */ 762 static int __init dryice_rtc_probe(struct platform_device *pdev) 763 { 764 struct resource *res; 765 struct imxdi_dev *imxdi; 766 int norm_irq, sec_irq; 767 int rc; 768 769 imxdi = devm_kzalloc(&pdev->dev, sizeof(*imxdi), GFP_KERNEL); 770 if (!imxdi) 771 return -ENOMEM; 772 773 imxdi->pdev = pdev; 774 775 res = platform_get_resource(pdev, IORESOURCE_MEM, 0); 776 imxdi->ioaddr = devm_ioremap_resource(&pdev->dev, res); 777 if (IS_ERR(imxdi->ioaddr)) 778 return PTR_ERR(imxdi->ioaddr); 779 780 spin_lock_init(&imxdi->irq_lock); 781 782 norm_irq = platform_get_irq(pdev, 0); 783 if (norm_irq < 0) 784 return norm_irq; 785 786 /* the 2nd irq is the security violation irq 787 * make this optional, don't break the device tree ABI 788 */ 789 sec_irq = platform_get_irq(pdev, 1); 790 if (sec_irq <= 0) 791 sec_irq = IRQ_NOTCONNECTED; 792 793 init_waitqueue_head(&imxdi->write_wait); 794 795 INIT_WORK(&imxdi->work, dryice_work); 796 797 mutex_init(&imxdi->write_mutex); 798 799 imxdi->clk = devm_clk_get(&pdev->dev, NULL); 800 if (IS_ERR(imxdi->clk)) 801 return PTR_ERR(imxdi->clk); 802 rc = clk_prepare_enable(imxdi->clk); 803 if (rc) 804 return rc; 805 806 /* 807 * Initialize dryice hardware 808 */ 809 810 /* mask all interrupts */ 811 writel(0, imxdi->ioaddr + DIER); 812 813 rc = di_handle_state(imxdi); 814 if (rc != 0) 815 goto err; 816 817 rc = devm_request_irq(&pdev->dev, norm_irq, dryice_irq, 818 IRQF_SHARED, pdev->name, imxdi); 819 if (rc) { 820 dev_warn(&pdev->dev, "interrupt not available.\n"); 821 goto err; 822 } 823 824 rc = devm_request_irq(&pdev->dev, sec_irq, dryice_irq, 825 IRQF_SHARED, pdev->name, imxdi); 826 if (rc) { 827 dev_warn(&pdev->dev, "security violation interrupt not available.\n"); 828 /* this is not an error, see above */ 829 } 830 831 platform_set_drvdata(pdev, imxdi); 832 imxdi->rtc = devm_rtc_device_register(&pdev->dev, pdev->name, 833 &dryice_rtc_ops, THIS_MODULE); 834 if (IS_ERR(imxdi->rtc)) { 835 rc = PTR_ERR(imxdi->rtc); 836 goto err; 837 } 838 839 return 0; 840 841 err: 842 clk_disable_unprepare(imxdi->clk); 843 844 return rc; 845 } 846 847 static int __exit dryice_rtc_remove(struct platform_device *pdev) 848 { 849 struct imxdi_dev *imxdi = platform_get_drvdata(pdev); 850 851 flush_work(&imxdi->work); 852 853 /* mask all interrupts */ 854 writel(0, imxdi->ioaddr + DIER); 855 856 clk_disable_unprepare(imxdi->clk); 857 858 return 0; 859 } 860 861 #ifdef CONFIG_OF 862 static const struct of_device_id dryice_dt_ids[] = { 863 { .compatible = "fsl,imx25-rtc" }, 864 { /* sentinel */ } 865 }; 866 867 MODULE_DEVICE_TABLE(of, dryice_dt_ids); 868 #endif 869 870 static struct platform_driver dryice_rtc_driver = { 871 .driver = { 872 .name = "imxdi_rtc", 873 .of_match_table = of_match_ptr(dryice_dt_ids), 874 }, 875 .remove = __exit_p(dryice_rtc_remove), 876 }; 877 878 module_platform_driver_probe(dryice_rtc_driver, dryice_rtc_probe); 879 880 MODULE_AUTHOR("Freescale Semiconductor, Inc."); 881 MODULE_AUTHOR("Baruch Siach <baruch@tkos.co.il>"); 882 MODULE_DESCRIPTION("IMX DryIce Realtime Clock Driver (RTC)"); 883 MODULE_LICENSE("GPL"); 884