1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * rtc-ds1305.c -- driver for DS1305 and DS1306 SPI RTC chips 4 * 5 * Copyright (C) 2008 David Brownell 6 */ 7 #include <linux/kernel.h> 8 #include <linux/init.h> 9 #include <linux/bcd.h> 10 #include <linux/slab.h> 11 #include <linux/rtc.h> 12 #include <linux/workqueue.h> 13 14 #include <linux/spi/spi.h> 15 #include <linux/spi/ds1305.h> 16 #include <linux/module.h> 17 18 19 /* 20 * Registers ... mask DS1305_WRITE into register address to write, 21 * otherwise you're reading it. All non-bitmask values are BCD. 22 */ 23 #define DS1305_WRITE 0x80 24 25 26 /* RTC date/time ... the main special cases are that we: 27 * - Need fancy "hours" encoding in 12hour mode 28 * - Don't rely on the "day-of-week" field (or tm_wday) 29 * - Are a 21st-century clock (2000 <= year < 2100) 30 */ 31 #define DS1305_RTC_LEN 7 /* bytes for RTC regs */ 32 33 #define DS1305_SEC 0x00 /* register addresses */ 34 #define DS1305_MIN 0x01 35 #define DS1305_HOUR 0x02 36 # define DS1305_HR_12 0x40 /* set == 12 hr mode */ 37 # define DS1305_HR_PM 0x20 /* set == PM (12hr mode) */ 38 #define DS1305_WDAY 0x03 39 #define DS1305_MDAY 0x04 40 #define DS1305_MON 0x05 41 #define DS1305_YEAR 0x06 42 43 44 /* The two alarms have only sec/min/hour/wday fields (ALM_LEN). 45 * DS1305_ALM_DISABLE disables a match field (some combos are bad). 46 * 47 * NOTE that since we don't use WDAY, we limit ourselves to alarms 48 * only one day into the future (vs potentially up to a week). 49 * 50 * NOTE ALSO that while we could generate once-a-second IRQs (UIE), we 51 * don't currently support them. We'd either need to do it only when 52 * no alarm is pending (not the standard model), or to use the second 53 * alarm (implying that this is a DS1305 not DS1306, *and* that either 54 * it's wired up a second IRQ we know, or that INTCN is set) 55 */ 56 #define DS1305_ALM_LEN 4 /* bytes for ALM regs */ 57 #define DS1305_ALM_DISABLE 0x80 58 59 #define DS1305_ALM0(r) (0x07 + (r)) /* register addresses */ 60 #define DS1305_ALM1(r) (0x0b + (r)) 61 62 63 /* three control registers */ 64 #define DS1305_CONTROL_LEN 3 /* bytes of control regs */ 65 66 #define DS1305_CONTROL 0x0f /* register addresses */ 67 # define DS1305_nEOSC 0x80 /* low enables oscillator */ 68 # define DS1305_WP 0x40 /* write protect */ 69 # define DS1305_INTCN 0x04 /* clear == only int0 used */ 70 # define DS1306_1HZ 0x04 /* enable 1Hz output */ 71 # define DS1305_AEI1 0x02 /* enable ALM1 IRQ */ 72 # define DS1305_AEI0 0x01 /* enable ALM0 IRQ */ 73 #define DS1305_STATUS 0x10 74 /* status has just AEIx bits, mirrored as IRQFx */ 75 #define DS1305_TRICKLE 0x11 76 /* trickle bits are defined in <linux/spi/ds1305.h> */ 77 78 /* a bunch of NVRAM */ 79 #define DS1305_NVRAM_LEN 96 /* bytes of NVRAM */ 80 81 #define DS1305_NVRAM 0x20 /* register addresses */ 82 83 84 struct ds1305 { 85 struct spi_device *spi; 86 struct rtc_device *rtc; 87 88 struct work_struct work; 89 90 unsigned long flags; 91 #define FLAG_EXITING 0 92 93 bool hr12; 94 u8 ctrl[DS1305_CONTROL_LEN]; 95 }; 96 97 98 /*----------------------------------------------------------------------*/ 99 100 /* 101 * Utilities ... tolerate 12-hour AM/PM notation in case of non-Linux 102 * software (like a bootloader) which may require it. 103 */ 104 105 static unsigned bcd2hour(u8 bcd) 106 { 107 if (bcd & DS1305_HR_12) { 108 unsigned hour = 0; 109 110 bcd &= ~DS1305_HR_12; 111 if (bcd & DS1305_HR_PM) { 112 hour = 12; 113 bcd &= ~DS1305_HR_PM; 114 } 115 hour += bcd2bin(bcd); 116 return hour - 1; 117 } 118 return bcd2bin(bcd); 119 } 120 121 static u8 hour2bcd(bool hr12, int hour) 122 { 123 if (hr12) { 124 hour++; 125 if (hour <= 12) 126 return DS1305_HR_12 | bin2bcd(hour); 127 hour -= 12; 128 return DS1305_HR_12 | DS1305_HR_PM | bin2bcd(hour); 129 } 130 return bin2bcd(hour); 131 } 132 133 /*----------------------------------------------------------------------*/ 134 135 /* 136 * Interface to RTC framework 137 */ 138 139 static int ds1305_alarm_irq_enable(struct device *dev, unsigned int enabled) 140 { 141 struct ds1305 *ds1305 = dev_get_drvdata(dev); 142 u8 buf[2]; 143 long err = -EINVAL; 144 145 buf[0] = DS1305_WRITE | DS1305_CONTROL; 146 buf[1] = ds1305->ctrl[0]; 147 148 if (enabled) { 149 if (ds1305->ctrl[0] & DS1305_AEI0) 150 goto done; 151 buf[1] |= DS1305_AEI0; 152 } else { 153 if (!(buf[1] & DS1305_AEI0)) 154 goto done; 155 buf[1] &= ~DS1305_AEI0; 156 } 157 err = spi_write_then_read(ds1305->spi, buf, sizeof(buf), NULL, 0); 158 if (err >= 0) 159 ds1305->ctrl[0] = buf[1]; 160 done: 161 return err; 162 163 } 164 165 166 /* 167 * Get/set of date and time is pretty normal. 168 */ 169 170 static int ds1305_get_time(struct device *dev, struct rtc_time *time) 171 { 172 struct ds1305 *ds1305 = dev_get_drvdata(dev); 173 u8 addr = DS1305_SEC; 174 u8 buf[DS1305_RTC_LEN]; 175 int status; 176 177 /* Use write-then-read to get all the date/time registers 178 * since dma from stack is nonportable 179 */ 180 status = spi_write_then_read(ds1305->spi, &addr, sizeof(addr), 181 buf, sizeof(buf)); 182 if (status < 0) 183 return status; 184 185 dev_vdbg(dev, "%s: %3ph, %4ph\n", "read", &buf[0], &buf[3]); 186 187 /* Decode the registers */ 188 time->tm_sec = bcd2bin(buf[DS1305_SEC]); 189 time->tm_min = bcd2bin(buf[DS1305_MIN]); 190 time->tm_hour = bcd2hour(buf[DS1305_HOUR]); 191 time->tm_wday = buf[DS1305_WDAY] - 1; 192 time->tm_mday = bcd2bin(buf[DS1305_MDAY]); 193 time->tm_mon = bcd2bin(buf[DS1305_MON]) - 1; 194 time->tm_year = bcd2bin(buf[DS1305_YEAR]) + 100; 195 196 dev_vdbg(dev, "%s secs=%d, mins=%d, " 197 "hours=%d, mday=%d, mon=%d, year=%d, wday=%d\n", 198 "read", time->tm_sec, time->tm_min, 199 time->tm_hour, time->tm_mday, 200 time->tm_mon, time->tm_year, time->tm_wday); 201 202 return 0; 203 } 204 205 static int ds1305_set_time(struct device *dev, struct rtc_time *time) 206 { 207 struct ds1305 *ds1305 = dev_get_drvdata(dev); 208 u8 buf[1 + DS1305_RTC_LEN]; 209 u8 *bp = buf; 210 211 dev_vdbg(dev, "%s secs=%d, mins=%d, " 212 "hours=%d, mday=%d, mon=%d, year=%d, wday=%d\n", 213 "write", time->tm_sec, time->tm_min, 214 time->tm_hour, time->tm_mday, 215 time->tm_mon, time->tm_year, time->tm_wday); 216 217 /* Write registers starting at the first time/date address. */ 218 *bp++ = DS1305_WRITE | DS1305_SEC; 219 220 *bp++ = bin2bcd(time->tm_sec); 221 *bp++ = bin2bcd(time->tm_min); 222 *bp++ = hour2bcd(ds1305->hr12, time->tm_hour); 223 *bp++ = (time->tm_wday < 7) ? (time->tm_wday + 1) : 1; 224 *bp++ = bin2bcd(time->tm_mday); 225 *bp++ = bin2bcd(time->tm_mon + 1); 226 *bp++ = bin2bcd(time->tm_year - 100); 227 228 dev_dbg(dev, "%s: %3ph, %4ph\n", "write", &buf[1], &buf[4]); 229 230 /* use write-then-read since dma from stack is nonportable */ 231 return spi_write_then_read(ds1305->spi, buf, sizeof(buf), 232 NULL, 0); 233 } 234 235 /* 236 * Get/set of alarm is a bit funky: 237 * 238 * - First there's the inherent raciness of getting the (partitioned) 239 * status of an alarm that could trigger while we're reading parts 240 * of that status. 241 * 242 * - Second there's its limited range (we could increase it a bit by 243 * relying on WDAY), which means it will easily roll over. 244 * 245 * - Third there's the choice of two alarms and alarm signals. 246 * Here we use ALM0 and expect that nINT0 (open drain) is used; 247 * that's the only real option for DS1306 runtime alarms, and is 248 * natural on DS1305. 249 * 250 * - Fourth, there's also ALM1, and a second interrupt signal: 251 * + On DS1305 ALM1 uses nINT1 (when INTCN=1) else nINT0; 252 * + On DS1306 ALM1 only uses INT1 (an active high pulse) 253 * and it won't work when VCC1 is active. 254 * 255 * So to be most general, we should probably set both alarms to the 256 * same value, letting ALM1 be the wakeup event source on DS1306 257 * and handling several wiring options on DS1305. 258 * 259 * - Fifth, we support the polled mode (as well as possible; why not?) 260 * even when no interrupt line is wired to an IRQ. 261 */ 262 263 /* 264 * Context: caller holds rtc->ops_lock (to protect ds1305->ctrl) 265 */ 266 static int ds1305_get_alarm(struct device *dev, struct rtc_wkalrm *alm) 267 { 268 struct ds1305 *ds1305 = dev_get_drvdata(dev); 269 struct spi_device *spi = ds1305->spi; 270 u8 addr; 271 int status; 272 u8 buf[DS1305_ALM_LEN]; 273 274 /* Refresh control register cache BEFORE reading ALM0 registers, 275 * since reading alarm registers acks any pending IRQ. That 276 * makes returning "pending" status a bit of a lie, but that bit 277 * of EFI status is at best fragile anyway (given IRQ handlers). 278 */ 279 addr = DS1305_CONTROL; 280 status = spi_write_then_read(spi, &addr, sizeof(addr), 281 ds1305->ctrl, sizeof(ds1305->ctrl)); 282 if (status < 0) 283 return status; 284 285 alm->enabled = !!(ds1305->ctrl[0] & DS1305_AEI0); 286 alm->pending = !!(ds1305->ctrl[1] & DS1305_AEI0); 287 288 /* get and check ALM0 registers */ 289 addr = DS1305_ALM0(DS1305_SEC); 290 status = spi_write_then_read(spi, &addr, sizeof(addr), 291 buf, sizeof(buf)); 292 if (status < 0) 293 return status; 294 295 dev_vdbg(dev, "%s: %02x %02x %02x %02x\n", 296 "alm0 read", buf[DS1305_SEC], buf[DS1305_MIN], 297 buf[DS1305_HOUR], buf[DS1305_WDAY]); 298 299 if ((DS1305_ALM_DISABLE & buf[DS1305_SEC]) 300 || (DS1305_ALM_DISABLE & buf[DS1305_MIN]) 301 || (DS1305_ALM_DISABLE & buf[DS1305_HOUR])) 302 return -EIO; 303 304 /* Stuff these values into alm->time and let RTC framework code 305 * fill in the rest ... and also handle rollover to tomorrow when 306 * that's needed. 307 */ 308 alm->time.tm_sec = bcd2bin(buf[DS1305_SEC]); 309 alm->time.tm_min = bcd2bin(buf[DS1305_MIN]); 310 alm->time.tm_hour = bcd2hour(buf[DS1305_HOUR]); 311 312 return 0; 313 } 314 315 /* 316 * Context: caller holds rtc->ops_lock (to protect ds1305->ctrl) 317 */ 318 static int ds1305_set_alarm(struct device *dev, struct rtc_wkalrm *alm) 319 { 320 struct ds1305 *ds1305 = dev_get_drvdata(dev); 321 struct spi_device *spi = ds1305->spi; 322 unsigned long now, later; 323 struct rtc_time tm; 324 int status; 325 u8 buf[1 + DS1305_ALM_LEN]; 326 327 /* convert desired alarm to time_t */ 328 status = rtc_tm_to_time(&alm->time, &later); 329 if (status < 0) 330 return status; 331 332 /* Read current time as time_t */ 333 status = ds1305_get_time(dev, &tm); 334 if (status < 0) 335 return status; 336 status = rtc_tm_to_time(&tm, &now); 337 if (status < 0) 338 return status; 339 340 /* make sure alarm fires within the next 24 hours */ 341 if (later <= now) 342 return -EINVAL; 343 if ((later - now) > 24 * 60 * 60) 344 return -EDOM; 345 346 /* disable alarm if needed */ 347 if (ds1305->ctrl[0] & DS1305_AEI0) { 348 ds1305->ctrl[0] &= ~DS1305_AEI0; 349 350 buf[0] = DS1305_WRITE | DS1305_CONTROL; 351 buf[1] = ds1305->ctrl[0]; 352 status = spi_write_then_read(ds1305->spi, buf, 2, NULL, 0); 353 if (status < 0) 354 return status; 355 } 356 357 /* write alarm */ 358 buf[0] = DS1305_WRITE | DS1305_ALM0(DS1305_SEC); 359 buf[1 + DS1305_SEC] = bin2bcd(alm->time.tm_sec); 360 buf[1 + DS1305_MIN] = bin2bcd(alm->time.tm_min); 361 buf[1 + DS1305_HOUR] = hour2bcd(ds1305->hr12, alm->time.tm_hour); 362 buf[1 + DS1305_WDAY] = DS1305_ALM_DISABLE; 363 364 dev_dbg(dev, "%s: %02x %02x %02x %02x\n", 365 "alm0 write", buf[1 + DS1305_SEC], buf[1 + DS1305_MIN], 366 buf[1 + DS1305_HOUR], buf[1 + DS1305_WDAY]); 367 368 status = spi_write_then_read(spi, buf, sizeof(buf), NULL, 0); 369 if (status < 0) 370 return status; 371 372 /* enable alarm if requested */ 373 if (alm->enabled) { 374 ds1305->ctrl[0] |= DS1305_AEI0; 375 376 buf[0] = DS1305_WRITE | DS1305_CONTROL; 377 buf[1] = ds1305->ctrl[0]; 378 status = spi_write_then_read(ds1305->spi, buf, 2, NULL, 0); 379 } 380 381 return status; 382 } 383 384 #ifdef CONFIG_PROC_FS 385 386 static int ds1305_proc(struct device *dev, struct seq_file *seq) 387 { 388 struct ds1305 *ds1305 = dev_get_drvdata(dev); 389 char *diodes = "no"; 390 char *resistors = ""; 391 392 /* ctrl[2] is treated as read-only; no locking needed */ 393 if ((ds1305->ctrl[2] & 0xf0) == DS1305_TRICKLE_MAGIC) { 394 switch (ds1305->ctrl[2] & 0x0c) { 395 case DS1305_TRICKLE_DS2: 396 diodes = "2 diodes, "; 397 break; 398 case DS1305_TRICKLE_DS1: 399 diodes = "1 diode, "; 400 break; 401 default: 402 goto done; 403 } 404 switch (ds1305->ctrl[2] & 0x03) { 405 case DS1305_TRICKLE_2K: 406 resistors = "2k Ohm"; 407 break; 408 case DS1305_TRICKLE_4K: 409 resistors = "4k Ohm"; 410 break; 411 case DS1305_TRICKLE_8K: 412 resistors = "8k Ohm"; 413 break; 414 default: 415 diodes = "no"; 416 break; 417 } 418 } 419 420 done: 421 seq_printf(seq, "trickle_charge\t: %s%s\n", diodes, resistors); 422 423 return 0; 424 } 425 426 #else 427 #define ds1305_proc NULL 428 #endif 429 430 static const struct rtc_class_ops ds1305_ops = { 431 .read_time = ds1305_get_time, 432 .set_time = ds1305_set_time, 433 .read_alarm = ds1305_get_alarm, 434 .set_alarm = ds1305_set_alarm, 435 .proc = ds1305_proc, 436 .alarm_irq_enable = ds1305_alarm_irq_enable, 437 }; 438 439 static void ds1305_work(struct work_struct *work) 440 { 441 struct ds1305 *ds1305 = container_of(work, struct ds1305, work); 442 struct mutex *lock = &ds1305->rtc->ops_lock; 443 struct spi_device *spi = ds1305->spi; 444 u8 buf[3]; 445 int status; 446 447 /* lock to protect ds1305->ctrl */ 448 mutex_lock(lock); 449 450 /* Disable the IRQ, and clear its status ... for now, we "know" 451 * that if more than one alarm is active, they're in sync. 452 * Note that reading ALM data registers also clears IRQ status. 453 */ 454 ds1305->ctrl[0] &= ~(DS1305_AEI1 | DS1305_AEI0); 455 ds1305->ctrl[1] = 0; 456 457 buf[0] = DS1305_WRITE | DS1305_CONTROL; 458 buf[1] = ds1305->ctrl[0]; 459 buf[2] = 0; 460 461 status = spi_write_then_read(spi, buf, sizeof(buf), 462 NULL, 0); 463 if (status < 0) 464 dev_dbg(&spi->dev, "clear irq --> %d\n", status); 465 466 mutex_unlock(lock); 467 468 if (!test_bit(FLAG_EXITING, &ds1305->flags)) 469 enable_irq(spi->irq); 470 471 rtc_update_irq(ds1305->rtc, 1, RTC_AF | RTC_IRQF); 472 } 473 474 /* 475 * This "real" IRQ handler hands off to a workqueue mostly to allow 476 * mutex locking for ds1305->ctrl ... unlike I2C, we could issue async 477 * I/O requests in IRQ context (to clear the IRQ status). 478 */ 479 static irqreturn_t ds1305_irq(int irq, void *p) 480 { 481 struct ds1305 *ds1305 = p; 482 483 disable_irq(irq); 484 schedule_work(&ds1305->work); 485 return IRQ_HANDLED; 486 } 487 488 /*----------------------------------------------------------------------*/ 489 490 /* 491 * Interface for NVRAM 492 */ 493 494 static void msg_init(struct spi_message *m, struct spi_transfer *x, 495 u8 *addr, size_t count, char *tx, char *rx) 496 { 497 spi_message_init(m); 498 memset(x, 0, 2 * sizeof(*x)); 499 500 x->tx_buf = addr; 501 x->len = 1; 502 spi_message_add_tail(x, m); 503 504 x++; 505 506 x->tx_buf = tx; 507 x->rx_buf = rx; 508 x->len = count; 509 spi_message_add_tail(x, m); 510 } 511 512 static int ds1305_nvram_read(void *priv, unsigned int off, void *buf, 513 size_t count) 514 { 515 struct ds1305 *ds1305 = priv; 516 struct spi_device *spi = ds1305->spi; 517 u8 addr; 518 struct spi_message m; 519 struct spi_transfer x[2]; 520 521 addr = DS1305_NVRAM + off; 522 msg_init(&m, x, &addr, count, NULL, buf); 523 524 return spi_sync(spi, &m); 525 } 526 527 static int ds1305_nvram_write(void *priv, unsigned int off, void *buf, 528 size_t count) 529 { 530 struct ds1305 *ds1305 = priv; 531 struct spi_device *spi = ds1305->spi; 532 u8 addr; 533 struct spi_message m; 534 struct spi_transfer x[2]; 535 536 addr = (DS1305_WRITE | DS1305_NVRAM) + off; 537 msg_init(&m, x, &addr, count, buf, NULL); 538 539 return spi_sync(spi, &m); 540 } 541 542 /*----------------------------------------------------------------------*/ 543 544 /* 545 * Interface to SPI stack 546 */ 547 548 static int ds1305_probe(struct spi_device *spi) 549 { 550 struct ds1305 *ds1305; 551 int status; 552 u8 addr, value; 553 struct ds1305_platform_data *pdata = dev_get_platdata(&spi->dev); 554 bool write_ctrl = false; 555 struct nvmem_config ds1305_nvmem_cfg = { 556 .name = "ds1305_nvram", 557 .word_size = 1, 558 .stride = 1, 559 .size = DS1305_NVRAM_LEN, 560 .reg_read = ds1305_nvram_read, 561 .reg_write = ds1305_nvram_write, 562 }; 563 564 /* Sanity check board setup data. This may be hooked up 565 * in 3wire mode, but we don't care. Note that unless 566 * there's an inverter in place, this needs SPI_CS_HIGH! 567 */ 568 if ((spi->bits_per_word && spi->bits_per_word != 8) 569 || (spi->max_speed_hz > 2000000) 570 || !(spi->mode & SPI_CPHA)) 571 return -EINVAL; 572 573 /* set up driver data */ 574 ds1305 = devm_kzalloc(&spi->dev, sizeof(*ds1305), GFP_KERNEL); 575 if (!ds1305) 576 return -ENOMEM; 577 ds1305->spi = spi; 578 spi_set_drvdata(spi, ds1305); 579 580 /* read and cache control registers */ 581 addr = DS1305_CONTROL; 582 status = spi_write_then_read(spi, &addr, sizeof(addr), 583 ds1305->ctrl, sizeof(ds1305->ctrl)); 584 if (status < 0) { 585 dev_dbg(&spi->dev, "can't %s, %d\n", 586 "read", status); 587 return status; 588 } 589 590 dev_dbg(&spi->dev, "ctrl %s: %3ph\n", "read", ds1305->ctrl); 591 592 /* Sanity check register values ... partially compensating for the 593 * fact that SPI has no device handshake. A pullup on MISO would 594 * make these tests fail; but not all systems will have one. If 595 * some register is neither 0x00 nor 0xff, a chip is likely there. 596 */ 597 if ((ds1305->ctrl[0] & 0x38) != 0 || (ds1305->ctrl[1] & 0xfc) != 0) { 598 dev_dbg(&spi->dev, "RTC chip is not present\n"); 599 return -ENODEV; 600 } 601 if (ds1305->ctrl[2] == 0) 602 dev_dbg(&spi->dev, "chip may not be present\n"); 603 604 /* enable writes if needed ... if we were paranoid it would 605 * make sense to enable them only when absolutely necessary. 606 */ 607 if (ds1305->ctrl[0] & DS1305_WP) { 608 u8 buf[2]; 609 610 ds1305->ctrl[0] &= ~DS1305_WP; 611 612 buf[0] = DS1305_WRITE | DS1305_CONTROL; 613 buf[1] = ds1305->ctrl[0]; 614 status = spi_write_then_read(spi, buf, sizeof(buf), NULL, 0); 615 616 dev_dbg(&spi->dev, "clear WP --> %d\n", status); 617 if (status < 0) 618 return status; 619 } 620 621 /* on DS1305, maybe start oscillator; like most low power 622 * oscillators, it may take a second to stabilize 623 */ 624 if (ds1305->ctrl[0] & DS1305_nEOSC) { 625 ds1305->ctrl[0] &= ~DS1305_nEOSC; 626 write_ctrl = true; 627 dev_warn(&spi->dev, "SET TIME!\n"); 628 } 629 630 /* ack any pending IRQs */ 631 if (ds1305->ctrl[1]) { 632 ds1305->ctrl[1] = 0; 633 write_ctrl = true; 634 } 635 636 /* this may need one-time (re)init */ 637 if (pdata) { 638 /* maybe enable trickle charge */ 639 if (((ds1305->ctrl[2] & 0xf0) != DS1305_TRICKLE_MAGIC)) { 640 ds1305->ctrl[2] = DS1305_TRICKLE_MAGIC 641 | pdata->trickle; 642 write_ctrl = true; 643 } 644 645 /* on DS1306, configure 1 Hz signal */ 646 if (pdata->is_ds1306) { 647 if (pdata->en_1hz) { 648 if (!(ds1305->ctrl[0] & DS1306_1HZ)) { 649 ds1305->ctrl[0] |= DS1306_1HZ; 650 write_ctrl = true; 651 } 652 } else { 653 if (ds1305->ctrl[0] & DS1306_1HZ) { 654 ds1305->ctrl[0] &= ~DS1306_1HZ; 655 write_ctrl = true; 656 } 657 } 658 } 659 } 660 661 if (write_ctrl) { 662 u8 buf[4]; 663 664 buf[0] = DS1305_WRITE | DS1305_CONTROL; 665 buf[1] = ds1305->ctrl[0]; 666 buf[2] = ds1305->ctrl[1]; 667 buf[3] = ds1305->ctrl[2]; 668 status = spi_write_then_read(spi, buf, sizeof(buf), NULL, 0); 669 if (status < 0) { 670 dev_dbg(&spi->dev, "can't %s, %d\n", 671 "write", status); 672 return status; 673 } 674 675 dev_dbg(&spi->dev, "ctrl %s: %3ph\n", "write", ds1305->ctrl); 676 } 677 678 /* see if non-Linux software set up AM/PM mode */ 679 addr = DS1305_HOUR; 680 status = spi_write_then_read(spi, &addr, sizeof(addr), 681 &value, sizeof(value)); 682 if (status < 0) { 683 dev_dbg(&spi->dev, "read HOUR --> %d\n", status); 684 return status; 685 } 686 687 ds1305->hr12 = (DS1305_HR_12 & value) != 0; 688 if (ds1305->hr12) 689 dev_dbg(&spi->dev, "AM/PM\n"); 690 691 /* register RTC ... from here on, ds1305->ctrl needs locking */ 692 ds1305->rtc = devm_rtc_allocate_device(&spi->dev); 693 if (IS_ERR(ds1305->rtc)) 694 return PTR_ERR(ds1305->rtc); 695 696 ds1305->rtc->ops = &ds1305_ops; 697 698 ds1305_nvmem_cfg.priv = ds1305; 699 ds1305->rtc->nvram_old_abi = true; 700 status = rtc_register_device(ds1305->rtc); 701 if (status) 702 return status; 703 704 rtc_nvmem_register(ds1305->rtc, &ds1305_nvmem_cfg); 705 706 /* Maybe set up alarm IRQ; be ready to handle it triggering right 707 * away. NOTE that we don't share this. The signal is active low, 708 * and we can't ack it before a SPI message delay. We temporarily 709 * disable the IRQ until it's acked, which lets us work with more 710 * IRQ trigger modes (not all IRQ controllers can do falling edge). 711 */ 712 if (spi->irq) { 713 INIT_WORK(&ds1305->work, ds1305_work); 714 status = devm_request_irq(&spi->dev, spi->irq, ds1305_irq, 715 0, dev_name(&ds1305->rtc->dev), ds1305); 716 if (status < 0) { 717 dev_err(&spi->dev, "request_irq %d --> %d\n", 718 spi->irq, status); 719 } else { 720 device_set_wakeup_capable(&spi->dev, 1); 721 } 722 } 723 724 return 0; 725 } 726 727 static int ds1305_remove(struct spi_device *spi) 728 { 729 struct ds1305 *ds1305 = spi_get_drvdata(spi); 730 731 /* carefully shut down irq and workqueue, if present */ 732 if (spi->irq) { 733 set_bit(FLAG_EXITING, &ds1305->flags); 734 devm_free_irq(&spi->dev, spi->irq, ds1305); 735 cancel_work_sync(&ds1305->work); 736 } 737 738 return 0; 739 } 740 741 static struct spi_driver ds1305_driver = { 742 .driver.name = "rtc-ds1305", 743 .probe = ds1305_probe, 744 .remove = ds1305_remove, 745 /* REVISIT add suspend/resume */ 746 }; 747 748 module_spi_driver(ds1305_driver); 749 750 MODULE_DESCRIPTION("RTC driver for DS1305 and DS1306 chips"); 751 MODULE_LICENSE("GPL"); 752 MODULE_ALIAS("spi:rtc-ds1305"); 753