1 /* 2 * rtc-ds1305.c -- driver for DS1305 and DS1306 SPI RTC chips 3 * 4 * Copyright (C) 2008 David Brownell 5 * 6 * This program is free software; you can redistribute it and/or modify 7 * it under the terms of the GNU General Public License version 2 as 8 * published by the Free Software Foundation. 9 * 10 */ 11 #include <linux/kernel.h> 12 #include <linux/init.h> 13 #include <linux/bcd.h> 14 #include <linux/slab.h> 15 #include <linux/rtc.h> 16 #include <linux/workqueue.h> 17 18 #include <linux/spi/spi.h> 19 #include <linux/spi/ds1305.h> 20 #include <linux/module.h> 21 22 23 /* 24 * Registers ... mask DS1305_WRITE into register address to write, 25 * otherwise you're reading it. All non-bitmask values are BCD. 26 */ 27 #define DS1305_WRITE 0x80 28 29 30 /* RTC date/time ... the main special cases are that we: 31 * - Need fancy "hours" encoding in 12hour mode 32 * - Don't rely on the "day-of-week" field (or tm_wday) 33 * - Are a 21st-century clock (2000 <= year < 2100) 34 */ 35 #define DS1305_RTC_LEN 7 /* bytes for RTC regs */ 36 37 #define DS1305_SEC 0x00 /* register addresses */ 38 #define DS1305_MIN 0x01 39 #define DS1305_HOUR 0x02 40 # define DS1305_HR_12 0x40 /* set == 12 hr mode */ 41 # define DS1305_HR_PM 0x20 /* set == PM (12hr mode) */ 42 #define DS1305_WDAY 0x03 43 #define DS1305_MDAY 0x04 44 #define DS1305_MON 0x05 45 #define DS1305_YEAR 0x06 46 47 48 /* The two alarms have only sec/min/hour/wday fields (ALM_LEN). 49 * DS1305_ALM_DISABLE disables a match field (some combos are bad). 50 * 51 * NOTE that since we don't use WDAY, we limit ourselves to alarms 52 * only one day into the future (vs potentially up to a week). 53 * 54 * NOTE ALSO that while we could generate once-a-second IRQs (UIE), we 55 * don't currently support them. We'd either need to do it only when 56 * no alarm is pending (not the standard model), or to use the second 57 * alarm (implying that this is a DS1305 not DS1306, *and* that either 58 * it's wired up a second IRQ we know, or that INTCN is set) 59 */ 60 #define DS1305_ALM_LEN 4 /* bytes for ALM regs */ 61 #define DS1305_ALM_DISABLE 0x80 62 63 #define DS1305_ALM0(r) (0x07 + (r)) /* register addresses */ 64 #define DS1305_ALM1(r) (0x0b + (r)) 65 66 67 /* three control registers */ 68 #define DS1305_CONTROL_LEN 3 /* bytes of control regs */ 69 70 #define DS1305_CONTROL 0x0f /* register addresses */ 71 # define DS1305_nEOSC 0x80 /* low enables oscillator */ 72 # define DS1305_WP 0x40 /* write protect */ 73 # define DS1305_INTCN 0x04 /* clear == only int0 used */ 74 # define DS1306_1HZ 0x04 /* enable 1Hz output */ 75 # define DS1305_AEI1 0x02 /* enable ALM1 IRQ */ 76 # define DS1305_AEI0 0x01 /* enable ALM0 IRQ */ 77 #define DS1305_STATUS 0x10 78 /* status has just AEIx bits, mirrored as IRQFx */ 79 #define DS1305_TRICKLE 0x11 80 /* trickle bits are defined in <linux/spi/ds1305.h> */ 81 82 /* a bunch of NVRAM */ 83 #define DS1305_NVRAM_LEN 96 /* bytes of NVRAM */ 84 85 #define DS1305_NVRAM 0x20 /* register addresses */ 86 87 88 struct ds1305 { 89 struct spi_device *spi; 90 struct rtc_device *rtc; 91 92 struct work_struct work; 93 94 unsigned long flags; 95 #define FLAG_EXITING 0 96 97 bool hr12; 98 u8 ctrl[DS1305_CONTROL_LEN]; 99 }; 100 101 102 /*----------------------------------------------------------------------*/ 103 104 /* 105 * Utilities ... tolerate 12-hour AM/PM notation in case of non-Linux 106 * software (like a bootloader) which may require it. 107 */ 108 109 static unsigned bcd2hour(u8 bcd) 110 { 111 if (bcd & DS1305_HR_12) { 112 unsigned hour = 0; 113 114 bcd &= ~DS1305_HR_12; 115 if (bcd & DS1305_HR_PM) { 116 hour = 12; 117 bcd &= ~DS1305_HR_PM; 118 } 119 hour += bcd2bin(bcd); 120 return hour - 1; 121 } 122 return bcd2bin(bcd); 123 } 124 125 static u8 hour2bcd(bool hr12, int hour) 126 { 127 if (hr12) { 128 hour++; 129 if (hour <= 12) 130 return DS1305_HR_12 | bin2bcd(hour); 131 hour -= 12; 132 return DS1305_HR_12 | DS1305_HR_PM | bin2bcd(hour); 133 } 134 return bin2bcd(hour); 135 } 136 137 /*----------------------------------------------------------------------*/ 138 139 /* 140 * Interface to RTC framework 141 */ 142 143 static int ds1305_alarm_irq_enable(struct device *dev, unsigned int enabled) 144 { 145 struct ds1305 *ds1305 = dev_get_drvdata(dev); 146 u8 buf[2]; 147 long err = -EINVAL; 148 149 buf[0] = DS1305_WRITE | DS1305_CONTROL; 150 buf[1] = ds1305->ctrl[0]; 151 152 if (enabled) { 153 if (ds1305->ctrl[0] & DS1305_AEI0) 154 goto done; 155 buf[1] |= DS1305_AEI0; 156 } else { 157 if (!(buf[1] & DS1305_AEI0)) 158 goto done; 159 buf[1] &= ~DS1305_AEI0; 160 } 161 err = spi_write_then_read(ds1305->spi, buf, sizeof(buf), NULL, 0); 162 if (err >= 0) 163 ds1305->ctrl[0] = buf[1]; 164 done: 165 return err; 166 167 } 168 169 170 /* 171 * Get/set of date and time is pretty normal. 172 */ 173 174 static int ds1305_get_time(struct device *dev, struct rtc_time *time) 175 { 176 struct ds1305 *ds1305 = dev_get_drvdata(dev); 177 u8 addr = DS1305_SEC; 178 u8 buf[DS1305_RTC_LEN]; 179 int status; 180 181 /* Use write-then-read to get all the date/time registers 182 * since dma from stack is nonportable 183 */ 184 status = spi_write_then_read(ds1305->spi, &addr, sizeof(addr), 185 buf, sizeof(buf)); 186 if (status < 0) 187 return status; 188 189 dev_vdbg(dev, "%s: %3ph, %4ph\n", "read", &buf[0], &buf[3]); 190 191 /* Decode the registers */ 192 time->tm_sec = bcd2bin(buf[DS1305_SEC]); 193 time->tm_min = bcd2bin(buf[DS1305_MIN]); 194 time->tm_hour = bcd2hour(buf[DS1305_HOUR]); 195 time->tm_wday = buf[DS1305_WDAY] - 1; 196 time->tm_mday = bcd2bin(buf[DS1305_MDAY]); 197 time->tm_mon = bcd2bin(buf[DS1305_MON]) - 1; 198 time->tm_year = bcd2bin(buf[DS1305_YEAR]) + 100; 199 200 dev_vdbg(dev, "%s secs=%d, mins=%d, " 201 "hours=%d, mday=%d, mon=%d, year=%d, wday=%d\n", 202 "read", time->tm_sec, time->tm_min, 203 time->tm_hour, time->tm_mday, 204 time->tm_mon, time->tm_year, time->tm_wday); 205 206 /* Time may not be set */ 207 return rtc_valid_tm(time); 208 } 209 210 static int ds1305_set_time(struct device *dev, struct rtc_time *time) 211 { 212 struct ds1305 *ds1305 = dev_get_drvdata(dev); 213 u8 buf[1 + DS1305_RTC_LEN]; 214 u8 *bp = buf; 215 216 dev_vdbg(dev, "%s secs=%d, mins=%d, " 217 "hours=%d, mday=%d, mon=%d, year=%d, wday=%d\n", 218 "write", time->tm_sec, time->tm_min, 219 time->tm_hour, time->tm_mday, 220 time->tm_mon, time->tm_year, time->tm_wday); 221 222 /* Write registers starting at the first time/date address. */ 223 *bp++ = DS1305_WRITE | DS1305_SEC; 224 225 *bp++ = bin2bcd(time->tm_sec); 226 *bp++ = bin2bcd(time->tm_min); 227 *bp++ = hour2bcd(ds1305->hr12, time->tm_hour); 228 *bp++ = (time->tm_wday < 7) ? (time->tm_wday + 1) : 1; 229 *bp++ = bin2bcd(time->tm_mday); 230 *bp++ = bin2bcd(time->tm_mon + 1); 231 *bp++ = bin2bcd(time->tm_year - 100); 232 233 dev_dbg(dev, "%s: %3ph, %4ph\n", "write", &buf[1], &buf[4]); 234 235 /* use write-then-read since dma from stack is nonportable */ 236 return spi_write_then_read(ds1305->spi, buf, sizeof(buf), 237 NULL, 0); 238 } 239 240 /* 241 * Get/set of alarm is a bit funky: 242 * 243 * - First there's the inherent raciness of getting the (partitioned) 244 * status of an alarm that could trigger while we're reading parts 245 * of that status. 246 * 247 * - Second there's its limited range (we could increase it a bit by 248 * relying on WDAY), which means it will easily roll over. 249 * 250 * - Third there's the choice of two alarms and alarm signals. 251 * Here we use ALM0 and expect that nINT0 (open drain) is used; 252 * that's the only real option for DS1306 runtime alarms, and is 253 * natural on DS1305. 254 * 255 * - Fourth, there's also ALM1, and a second interrupt signal: 256 * + On DS1305 ALM1 uses nINT1 (when INTCN=1) else nINT0; 257 * + On DS1306 ALM1 only uses INT1 (an active high pulse) 258 * and it won't work when VCC1 is active. 259 * 260 * So to be most general, we should probably set both alarms to the 261 * same value, letting ALM1 be the wakeup event source on DS1306 262 * and handling several wiring options on DS1305. 263 * 264 * - Fifth, we support the polled mode (as well as possible; why not?) 265 * even when no interrupt line is wired to an IRQ. 266 */ 267 268 /* 269 * Context: caller holds rtc->ops_lock (to protect ds1305->ctrl) 270 */ 271 static int ds1305_get_alarm(struct device *dev, struct rtc_wkalrm *alm) 272 { 273 struct ds1305 *ds1305 = dev_get_drvdata(dev); 274 struct spi_device *spi = ds1305->spi; 275 u8 addr; 276 int status; 277 u8 buf[DS1305_ALM_LEN]; 278 279 /* Refresh control register cache BEFORE reading ALM0 registers, 280 * since reading alarm registers acks any pending IRQ. That 281 * makes returning "pending" status a bit of a lie, but that bit 282 * of EFI status is at best fragile anyway (given IRQ handlers). 283 */ 284 addr = DS1305_CONTROL; 285 status = spi_write_then_read(spi, &addr, sizeof(addr), 286 ds1305->ctrl, sizeof(ds1305->ctrl)); 287 if (status < 0) 288 return status; 289 290 alm->enabled = !!(ds1305->ctrl[0] & DS1305_AEI0); 291 alm->pending = !!(ds1305->ctrl[1] & DS1305_AEI0); 292 293 /* get and check ALM0 registers */ 294 addr = DS1305_ALM0(DS1305_SEC); 295 status = spi_write_then_read(spi, &addr, sizeof(addr), 296 buf, sizeof(buf)); 297 if (status < 0) 298 return status; 299 300 dev_vdbg(dev, "%s: %02x %02x %02x %02x\n", 301 "alm0 read", buf[DS1305_SEC], buf[DS1305_MIN], 302 buf[DS1305_HOUR], buf[DS1305_WDAY]); 303 304 if ((DS1305_ALM_DISABLE & buf[DS1305_SEC]) 305 || (DS1305_ALM_DISABLE & buf[DS1305_MIN]) 306 || (DS1305_ALM_DISABLE & buf[DS1305_HOUR])) 307 return -EIO; 308 309 /* Stuff these values into alm->time and let RTC framework code 310 * fill in the rest ... and also handle rollover to tomorrow when 311 * that's needed. 312 */ 313 alm->time.tm_sec = bcd2bin(buf[DS1305_SEC]); 314 alm->time.tm_min = bcd2bin(buf[DS1305_MIN]); 315 alm->time.tm_hour = bcd2hour(buf[DS1305_HOUR]); 316 317 return 0; 318 } 319 320 /* 321 * Context: caller holds rtc->ops_lock (to protect ds1305->ctrl) 322 */ 323 static int ds1305_set_alarm(struct device *dev, struct rtc_wkalrm *alm) 324 { 325 struct ds1305 *ds1305 = dev_get_drvdata(dev); 326 struct spi_device *spi = ds1305->spi; 327 unsigned long now, later; 328 struct rtc_time tm; 329 int status; 330 u8 buf[1 + DS1305_ALM_LEN]; 331 332 /* convert desired alarm to time_t */ 333 status = rtc_tm_to_time(&alm->time, &later); 334 if (status < 0) 335 return status; 336 337 /* Read current time as time_t */ 338 status = ds1305_get_time(dev, &tm); 339 if (status < 0) 340 return status; 341 status = rtc_tm_to_time(&tm, &now); 342 if (status < 0) 343 return status; 344 345 /* make sure alarm fires within the next 24 hours */ 346 if (later <= now) 347 return -EINVAL; 348 if ((later - now) > 24 * 60 * 60) 349 return -EDOM; 350 351 /* disable alarm if needed */ 352 if (ds1305->ctrl[0] & DS1305_AEI0) { 353 ds1305->ctrl[0] &= ~DS1305_AEI0; 354 355 buf[0] = DS1305_WRITE | DS1305_CONTROL; 356 buf[1] = ds1305->ctrl[0]; 357 status = spi_write_then_read(ds1305->spi, buf, 2, NULL, 0); 358 if (status < 0) 359 return status; 360 } 361 362 /* write alarm */ 363 buf[0] = DS1305_WRITE | DS1305_ALM0(DS1305_SEC); 364 buf[1 + DS1305_SEC] = bin2bcd(alm->time.tm_sec); 365 buf[1 + DS1305_MIN] = bin2bcd(alm->time.tm_min); 366 buf[1 + DS1305_HOUR] = hour2bcd(ds1305->hr12, alm->time.tm_hour); 367 buf[1 + DS1305_WDAY] = DS1305_ALM_DISABLE; 368 369 dev_dbg(dev, "%s: %02x %02x %02x %02x\n", 370 "alm0 write", buf[1 + DS1305_SEC], buf[1 + DS1305_MIN], 371 buf[1 + DS1305_HOUR], buf[1 + DS1305_WDAY]); 372 373 status = spi_write_then_read(spi, buf, sizeof(buf), NULL, 0); 374 if (status < 0) 375 return status; 376 377 /* enable alarm if requested */ 378 if (alm->enabled) { 379 ds1305->ctrl[0] |= DS1305_AEI0; 380 381 buf[0] = DS1305_WRITE | DS1305_CONTROL; 382 buf[1] = ds1305->ctrl[0]; 383 status = spi_write_then_read(ds1305->spi, buf, 2, NULL, 0); 384 } 385 386 return status; 387 } 388 389 #ifdef CONFIG_PROC_FS 390 391 static int ds1305_proc(struct device *dev, struct seq_file *seq) 392 { 393 struct ds1305 *ds1305 = dev_get_drvdata(dev); 394 char *diodes = "no"; 395 char *resistors = ""; 396 397 /* ctrl[2] is treated as read-only; no locking needed */ 398 if ((ds1305->ctrl[2] & 0xf0) == DS1305_TRICKLE_MAGIC) { 399 switch (ds1305->ctrl[2] & 0x0c) { 400 case DS1305_TRICKLE_DS2: 401 diodes = "2 diodes, "; 402 break; 403 case DS1305_TRICKLE_DS1: 404 diodes = "1 diode, "; 405 break; 406 default: 407 goto done; 408 } 409 switch (ds1305->ctrl[2] & 0x03) { 410 case DS1305_TRICKLE_2K: 411 resistors = "2k Ohm"; 412 break; 413 case DS1305_TRICKLE_4K: 414 resistors = "4k Ohm"; 415 break; 416 case DS1305_TRICKLE_8K: 417 resistors = "8k Ohm"; 418 break; 419 default: 420 diodes = "no"; 421 break; 422 } 423 } 424 425 done: 426 seq_printf(seq, "trickle_charge\t: %s%s\n", diodes, resistors); 427 428 return 0; 429 } 430 431 #else 432 #define ds1305_proc NULL 433 #endif 434 435 static const struct rtc_class_ops ds1305_ops = { 436 .read_time = ds1305_get_time, 437 .set_time = ds1305_set_time, 438 .read_alarm = ds1305_get_alarm, 439 .set_alarm = ds1305_set_alarm, 440 .proc = ds1305_proc, 441 .alarm_irq_enable = ds1305_alarm_irq_enable, 442 }; 443 444 static void ds1305_work(struct work_struct *work) 445 { 446 struct ds1305 *ds1305 = container_of(work, struct ds1305, work); 447 struct mutex *lock = &ds1305->rtc->ops_lock; 448 struct spi_device *spi = ds1305->spi; 449 u8 buf[3]; 450 int status; 451 452 /* lock to protect ds1305->ctrl */ 453 mutex_lock(lock); 454 455 /* Disable the IRQ, and clear its status ... for now, we "know" 456 * that if more than one alarm is active, they're in sync. 457 * Note that reading ALM data registers also clears IRQ status. 458 */ 459 ds1305->ctrl[0] &= ~(DS1305_AEI1 | DS1305_AEI0); 460 ds1305->ctrl[1] = 0; 461 462 buf[0] = DS1305_WRITE | DS1305_CONTROL; 463 buf[1] = ds1305->ctrl[0]; 464 buf[2] = 0; 465 466 status = spi_write_then_read(spi, buf, sizeof(buf), 467 NULL, 0); 468 if (status < 0) 469 dev_dbg(&spi->dev, "clear irq --> %d\n", status); 470 471 mutex_unlock(lock); 472 473 if (!test_bit(FLAG_EXITING, &ds1305->flags)) 474 enable_irq(spi->irq); 475 476 rtc_update_irq(ds1305->rtc, 1, RTC_AF | RTC_IRQF); 477 } 478 479 /* 480 * This "real" IRQ handler hands off to a workqueue mostly to allow 481 * mutex locking for ds1305->ctrl ... unlike I2C, we could issue async 482 * I/O requests in IRQ context (to clear the IRQ status). 483 */ 484 static irqreturn_t ds1305_irq(int irq, void *p) 485 { 486 struct ds1305 *ds1305 = p; 487 488 disable_irq(irq); 489 schedule_work(&ds1305->work); 490 return IRQ_HANDLED; 491 } 492 493 /*----------------------------------------------------------------------*/ 494 495 /* 496 * Interface for NVRAM 497 */ 498 499 static void msg_init(struct spi_message *m, struct spi_transfer *x, 500 u8 *addr, size_t count, char *tx, char *rx) 501 { 502 spi_message_init(m); 503 memset(x, 0, 2 * sizeof(*x)); 504 505 x->tx_buf = addr; 506 x->len = 1; 507 spi_message_add_tail(x, m); 508 509 x++; 510 511 x->tx_buf = tx; 512 x->rx_buf = rx; 513 x->len = count; 514 spi_message_add_tail(x, m); 515 } 516 517 static int ds1305_nvram_read(void *priv, unsigned int off, void *buf, 518 size_t count) 519 { 520 struct ds1305 *ds1305 = priv; 521 struct spi_device *spi = ds1305->spi; 522 u8 addr; 523 struct spi_message m; 524 struct spi_transfer x[2]; 525 526 addr = DS1305_NVRAM + off; 527 msg_init(&m, x, &addr, count, NULL, buf); 528 529 return spi_sync(spi, &m); 530 } 531 532 static int ds1305_nvram_write(void *priv, unsigned int off, void *buf, 533 size_t count) 534 { 535 struct ds1305 *ds1305 = priv; 536 struct spi_device *spi = ds1305->spi; 537 u8 addr; 538 struct spi_message m; 539 struct spi_transfer x[2]; 540 541 addr = (DS1305_WRITE | DS1305_NVRAM) + off; 542 msg_init(&m, x, &addr, count, buf, NULL); 543 544 return spi_sync(spi, &m); 545 } 546 547 static struct nvmem_config ds1305_nvmem_cfg = { 548 .name = "ds1305_nvram", 549 .word_size = 1, 550 .stride = 1, 551 .size = DS1305_NVRAM_LEN, 552 .reg_read = ds1305_nvram_read, 553 .reg_write = ds1305_nvram_write, 554 }; 555 556 /*----------------------------------------------------------------------*/ 557 558 /* 559 * Interface to SPI stack 560 */ 561 562 static int ds1305_probe(struct spi_device *spi) 563 { 564 struct ds1305 *ds1305; 565 int status; 566 u8 addr, value; 567 struct ds1305_platform_data *pdata = dev_get_platdata(&spi->dev); 568 bool write_ctrl = false; 569 570 /* Sanity check board setup data. This may be hooked up 571 * in 3wire mode, but we don't care. Note that unless 572 * there's an inverter in place, this needs SPI_CS_HIGH! 573 */ 574 if ((spi->bits_per_word && spi->bits_per_word != 8) 575 || (spi->max_speed_hz > 2000000) 576 || !(spi->mode & SPI_CPHA)) 577 return -EINVAL; 578 579 /* set up driver data */ 580 ds1305 = devm_kzalloc(&spi->dev, sizeof(*ds1305), GFP_KERNEL); 581 if (!ds1305) 582 return -ENOMEM; 583 ds1305->spi = spi; 584 spi_set_drvdata(spi, ds1305); 585 586 /* read and cache control registers */ 587 addr = DS1305_CONTROL; 588 status = spi_write_then_read(spi, &addr, sizeof(addr), 589 ds1305->ctrl, sizeof(ds1305->ctrl)); 590 if (status < 0) { 591 dev_dbg(&spi->dev, "can't %s, %d\n", 592 "read", status); 593 return status; 594 } 595 596 dev_dbg(&spi->dev, "ctrl %s: %3ph\n", "read", ds1305->ctrl); 597 598 /* Sanity check register values ... partially compensating for the 599 * fact that SPI has no device handshake. A pullup on MISO would 600 * make these tests fail; but not all systems will have one. If 601 * some register is neither 0x00 nor 0xff, a chip is likely there. 602 */ 603 if ((ds1305->ctrl[0] & 0x38) != 0 || (ds1305->ctrl[1] & 0xfc) != 0) { 604 dev_dbg(&spi->dev, "RTC chip is not present\n"); 605 return -ENODEV; 606 } 607 if (ds1305->ctrl[2] == 0) 608 dev_dbg(&spi->dev, "chip may not be present\n"); 609 610 /* enable writes if needed ... if we were paranoid it would 611 * make sense to enable them only when absolutely necessary. 612 */ 613 if (ds1305->ctrl[0] & DS1305_WP) { 614 u8 buf[2]; 615 616 ds1305->ctrl[0] &= ~DS1305_WP; 617 618 buf[0] = DS1305_WRITE | DS1305_CONTROL; 619 buf[1] = ds1305->ctrl[0]; 620 status = spi_write_then_read(spi, buf, sizeof(buf), NULL, 0); 621 622 dev_dbg(&spi->dev, "clear WP --> %d\n", status); 623 if (status < 0) 624 return status; 625 } 626 627 /* on DS1305, maybe start oscillator; like most low power 628 * oscillators, it may take a second to stabilize 629 */ 630 if (ds1305->ctrl[0] & DS1305_nEOSC) { 631 ds1305->ctrl[0] &= ~DS1305_nEOSC; 632 write_ctrl = true; 633 dev_warn(&spi->dev, "SET TIME!\n"); 634 } 635 636 /* ack any pending IRQs */ 637 if (ds1305->ctrl[1]) { 638 ds1305->ctrl[1] = 0; 639 write_ctrl = true; 640 } 641 642 /* this may need one-time (re)init */ 643 if (pdata) { 644 /* maybe enable trickle charge */ 645 if (((ds1305->ctrl[2] & 0xf0) != DS1305_TRICKLE_MAGIC)) { 646 ds1305->ctrl[2] = DS1305_TRICKLE_MAGIC 647 | pdata->trickle; 648 write_ctrl = true; 649 } 650 651 /* on DS1306, configure 1 Hz signal */ 652 if (pdata->is_ds1306) { 653 if (pdata->en_1hz) { 654 if (!(ds1305->ctrl[0] & DS1306_1HZ)) { 655 ds1305->ctrl[0] |= DS1306_1HZ; 656 write_ctrl = true; 657 } 658 } else { 659 if (ds1305->ctrl[0] & DS1306_1HZ) { 660 ds1305->ctrl[0] &= ~DS1306_1HZ; 661 write_ctrl = true; 662 } 663 } 664 } 665 } 666 667 if (write_ctrl) { 668 u8 buf[4]; 669 670 buf[0] = DS1305_WRITE | DS1305_CONTROL; 671 buf[1] = ds1305->ctrl[0]; 672 buf[2] = ds1305->ctrl[1]; 673 buf[3] = ds1305->ctrl[2]; 674 status = spi_write_then_read(spi, buf, sizeof(buf), NULL, 0); 675 if (status < 0) { 676 dev_dbg(&spi->dev, "can't %s, %d\n", 677 "write", status); 678 return status; 679 } 680 681 dev_dbg(&spi->dev, "ctrl %s: %3ph\n", "write", ds1305->ctrl); 682 } 683 684 /* see if non-Linux software set up AM/PM mode */ 685 addr = DS1305_HOUR; 686 status = spi_write_then_read(spi, &addr, sizeof(addr), 687 &value, sizeof(value)); 688 if (status < 0) { 689 dev_dbg(&spi->dev, "read HOUR --> %d\n", status); 690 return status; 691 } 692 693 ds1305->hr12 = (DS1305_HR_12 & value) != 0; 694 if (ds1305->hr12) 695 dev_dbg(&spi->dev, "AM/PM\n"); 696 697 /* register RTC ... from here on, ds1305->ctrl needs locking */ 698 ds1305->rtc = devm_rtc_allocate_device(&spi->dev); 699 if (IS_ERR(ds1305->rtc)) { 700 return PTR_ERR(ds1305->rtc); 701 } 702 703 ds1305->rtc->ops = &ds1305_ops; 704 705 ds1305_nvmem_cfg.priv = ds1305; 706 ds1305->rtc->nvmem_config = &ds1305_nvmem_cfg; 707 ds1305->rtc->nvram_old_abi = true; 708 709 status = rtc_register_device(ds1305->rtc); 710 if (status) { 711 dev_dbg(&spi->dev, "register rtc --> %d\n", status); 712 return status; 713 } 714 715 /* Maybe set up alarm IRQ; be ready to handle it triggering right 716 * away. NOTE that we don't share this. The signal is active low, 717 * and we can't ack it before a SPI message delay. We temporarily 718 * disable the IRQ until it's acked, which lets us work with more 719 * IRQ trigger modes (not all IRQ controllers can do falling edge). 720 */ 721 if (spi->irq) { 722 INIT_WORK(&ds1305->work, ds1305_work); 723 status = devm_request_irq(&spi->dev, spi->irq, ds1305_irq, 724 0, dev_name(&ds1305->rtc->dev), ds1305); 725 if (status < 0) { 726 dev_err(&spi->dev, "request_irq %d --> %d\n", 727 spi->irq, status); 728 } else { 729 device_set_wakeup_capable(&spi->dev, 1); 730 } 731 } 732 733 return 0; 734 } 735 736 static int ds1305_remove(struct spi_device *spi) 737 { 738 struct ds1305 *ds1305 = spi_get_drvdata(spi); 739 740 /* carefully shut down irq and workqueue, if present */ 741 if (spi->irq) { 742 set_bit(FLAG_EXITING, &ds1305->flags); 743 devm_free_irq(&spi->dev, spi->irq, ds1305); 744 cancel_work_sync(&ds1305->work); 745 } 746 747 return 0; 748 } 749 750 static struct spi_driver ds1305_driver = { 751 .driver.name = "rtc-ds1305", 752 .probe = ds1305_probe, 753 .remove = ds1305_remove, 754 /* REVISIT add suspend/resume */ 755 }; 756 757 module_spi_driver(ds1305_driver); 758 759 MODULE_DESCRIPTION("RTC driver for DS1305 and DS1306 chips"); 760 MODULE_LICENSE("GPL"); 761 MODULE_ALIAS("spi:rtc-ds1305"); 762