1 /* 2 * Texas Instruments SoC Adaptive Body Bias(ABB) Regulator 3 * 4 * Copyright (C) 2011 Texas Instruments, Inc. 5 * Mike Turquette <mturquette@ti.com> 6 * 7 * Copyright (C) 2012-2013 Texas Instruments, Inc. 8 * Andrii Tseglytskyi <andrii.tseglytskyi@ti.com> 9 * Nishanth Menon <nm@ti.com> 10 * 11 * This program is free software; you can redistribute it and/or modify 12 * it under the terms of the GNU General Public License version 2 as 13 * published by the Free Software Foundation. 14 * 15 * This program is distributed "as is" WITHOUT ANY WARRANTY of any 16 * kind, whether express or implied; without even the implied warranty 17 * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 18 * GNU General Public License for more details. 19 */ 20 #include <linux/clk.h> 21 #include <linux/delay.h> 22 #include <linux/err.h> 23 #include <linux/io.h> 24 #include <linux/module.h> 25 #include <linux/of_device.h> 26 #include <linux/of.h> 27 #include <linux/platform_device.h> 28 #include <linux/regulator/driver.h> 29 #include <linux/regulator/machine.h> 30 #include <linux/regulator/of_regulator.h> 31 32 /* 33 * ABB LDO operating states: 34 * NOMINAL_OPP: bypasses the ABB LDO 35 * FAST_OPP: sets ABB LDO to Forward Body-Bias 36 * SLOW_OPP: sets ABB LDO to Reverse Body-Bias 37 */ 38 #define TI_ABB_NOMINAL_OPP 0 39 #define TI_ABB_FAST_OPP 1 40 #define TI_ABB_SLOW_OPP 3 41 42 /** 43 * struct ti_abb_info - ABB information per voltage setting 44 * @opp_sel: one of TI_ABB macro 45 * @vset: (optional) vset value that LDOVBB needs to be overriden with. 46 * 47 * Array of per voltage entries organized in the same order as regulator_desc's 48 * volt_table list. (selector is used to index from this array) 49 */ 50 struct ti_abb_info { 51 u32 opp_sel; 52 u32 vset; 53 }; 54 55 /** 56 * struct ti_abb_reg - Register description for ABB block 57 * @setup_off: setup register offset from base 58 * @control_off: control register offset from base 59 * @sr2_wtcnt_value_mask: setup register- sr2_wtcnt_value mask 60 * @fbb_sel_mask: setup register- FBB sel mask 61 * @rbb_sel_mask: setup register- RBB sel mask 62 * @sr2_en_mask: setup register- enable mask 63 * @opp_change_mask: control register - mask to trigger LDOVBB change 64 * @opp_sel_mask: control register - mask for mode to operate 65 */ 66 struct ti_abb_reg { 67 u32 setup_off; 68 u32 control_off; 69 70 /* Setup register fields */ 71 u32 sr2_wtcnt_value_mask; 72 u32 fbb_sel_mask; 73 u32 rbb_sel_mask; 74 u32 sr2_en_mask; 75 76 /* Control register fields */ 77 u32 opp_change_mask; 78 u32 opp_sel_mask; 79 }; 80 81 /** 82 * struct ti_abb - ABB instance data 83 * @rdesc: regulator descriptor 84 * @clk: clock(usually sysclk) supplying ABB block 85 * @base: base address of ABB block 86 * @setup_reg: setup register of ABB block 87 * @control_reg: control register of ABB block 88 * @int_base: interrupt register base address 89 * @efuse_base: (optional) efuse base address for ABB modes 90 * @ldo_base: (optional) LDOVBB vset override base address 91 * @regs: pointer to struct ti_abb_reg for ABB block 92 * @txdone_mask: mask on int_base for tranxdone interrupt 93 * @ldovbb_override_mask: mask to ldo_base for overriding default LDO VBB 94 * vset with value from efuse 95 * @ldovbb_vset_mask: mask to ldo_base for providing the VSET override 96 * @info: array to per voltage ABB configuration 97 * @current_info_idx: current index to info 98 * @settling_time: SoC specific settling time for LDO VBB 99 */ 100 struct ti_abb { 101 struct regulator_desc rdesc; 102 struct clk *clk; 103 void __iomem *base; 104 void __iomem *setup_reg; 105 void __iomem *control_reg; 106 void __iomem *int_base; 107 void __iomem *efuse_base; 108 void __iomem *ldo_base; 109 110 const struct ti_abb_reg *regs; 111 u32 txdone_mask; 112 u32 ldovbb_override_mask; 113 u32 ldovbb_vset_mask; 114 115 struct ti_abb_info *info; 116 int current_info_idx; 117 118 u32 settling_time; 119 }; 120 121 /** 122 * ti_abb_rmw() - handy wrapper to set specific register bits 123 * @mask: mask for register field 124 * @value: value shifted to mask location and written 125 * @reg: register address 126 * 127 * Return: final register value (may be unused) 128 */ 129 static inline u32 ti_abb_rmw(u32 mask, u32 value, void __iomem *reg) 130 { 131 u32 val; 132 133 val = readl(reg); 134 val &= ~mask; 135 val |= (value << __ffs(mask)) & mask; 136 writel(val, reg); 137 138 return val; 139 } 140 141 /** 142 * ti_abb_check_txdone() - handy wrapper to check ABB tranxdone status 143 * @abb: pointer to the abb instance 144 * 145 * Return: true or false 146 */ 147 static inline bool ti_abb_check_txdone(const struct ti_abb *abb) 148 { 149 return !!(readl(abb->int_base) & abb->txdone_mask); 150 } 151 152 /** 153 * ti_abb_clear_txdone() - handy wrapper to clear ABB tranxdone status 154 * @abb: pointer to the abb instance 155 */ 156 static inline void ti_abb_clear_txdone(const struct ti_abb *abb) 157 { 158 writel(abb->txdone_mask, abb->int_base); 159 }; 160 161 /** 162 * ti_abb_wait_tranx() - waits for ABB tranxdone event 163 * @dev: device 164 * @abb: pointer to the abb instance 165 * 166 * Return: 0 on success or -ETIMEDOUT if the event is not cleared on time. 167 */ 168 static int ti_abb_wait_txdone(struct device *dev, struct ti_abb *abb) 169 { 170 int timeout = 0; 171 bool status; 172 173 while (timeout++ <= abb->settling_time) { 174 status = ti_abb_check_txdone(abb); 175 if (status) 176 return 0; 177 178 udelay(1); 179 } 180 181 dev_warn_ratelimited(dev, "%s:TRANXDONE timeout(%duS) int=0x%08x\n", 182 __func__, timeout, readl(abb->int_base)); 183 return -ETIMEDOUT; 184 } 185 186 /** 187 * ti_abb_clear_all_txdone() - clears ABB tranxdone event 188 * @dev: device 189 * @abb: pointer to the abb instance 190 * 191 * Return: 0 on success or -ETIMEDOUT if the event is not cleared on time. 192 */ 193 static int ti_abb_clear_all_txdone(struct device *dev, const struct ti_abb *abb) 194 { 195 int timeout = 0; 196 bool status; 197 198 while (timeout++ <= abb->settling_time) { 199 ti_abb_clear_txdone(abb); 200 201 status = ti_abb_check_txdone(abb); 202 if (!status) 203 return 0; 204 205 udelay(1); 206 } 207 208 dev_warn_ratelimited(dev, "%s:TRANXDONE timeout(%duS) int=0x%08x\n", 209 __func__, timeout, readl(abb->int_base)); 210 return -ETIMEDOUT; 211 } 212 213 /** 214 * ti_abb_program_ldovbb() - program LDOVBB register for override value 215 * @dev: device 216 * @abb: pointer to the abb instance 217 * @info: ABB info to program 218 */ 219 static void ti_abb_program_ldovbb(struct device *dev, const struct ti_abb *abb, 220 struct ti_abb_info *info) 221 { 222 u32 val; 223 224 val = readl(abb->ldo_base); 225 /* clear up previous values */ 226 val &= ~(abb->ldovbb_override_mask | abb->ldovbb_vset_mask); 227 228 switch (info->opp_sel) { 229 case TI_ABB_SLOW_OPP: 230 case TI_ABB_FAST_OPP: 231 val |= abb->ldovbb_override_mask; 232 val |= info->vset << __ffs(abb->ldovbb_vset_mask); 233 break; 234 } 235 236 writel(val, abb->ldo_base); 237 } 238 239 /** 240 * ti_abb_set_opp() - Setup ABB and LDO VBB for required bias 241 * @rdev: regulator device 242 * @abb: pointer to the abb instance 243 * @info: ABB info to program 244 * 245 * Return: 0 on success or appropriate error value when fails 246 */ 247 static int ti_abb_set_opp(struct regulator_dev *rdev, struct ti_abb *abb, 248 struct ti_abb_info *info) 249 { 250 const struct ti_abb_reg *regs = abb->regs; 251 struct device *dev = &rdev->dev; 252 int ret; 253 254 ret = ti_abb_clear_all_txdone(dev, abb); 255 if (ret) 256 goto out; 257 258 ti_abb_rmw(regs->fbb_sel_mask | regs->rbb_sel_mask, 0, abb->setup_reg); 259 260 switch (info->opp_sel) { 261 case TI_ABB_SLOW_OPP: 262 ti_abb_rmw(regs->rbb_sel_mask, 1, abb->setup_reg); 263 break; 264 case TI_ABB_FAST_OPP: 265 ti_abb_rmw(regs->fbb_sel_mask, 1, abb->setup_reg); 266 break; 267 } 268 269 /* program next state of ABB ldo */ 270 ti_abb_rmw(regs->opp_sel_mask, info->opp_sel, abb->control_reg); 271 272 /* 273 * program LDO VBB vset override if needed for !bypass mode 274 * XXX: Do not switch sequence - for !bypass, LDO override reset *must* 275 * be performed *before* switch to bias mode else VBB glitches. 276 */ 277 if (abb->ldo_base && info->opp_sel != TI_ABB_NOMINAL_OPP) 278 ti_abb_program_ldovbb(dev, abb, info); 279 280 /* Initiate ABB ldo change */ 281 ti_abb_rmw(regs->opp_change_mask, 1, abb->control_reg); 282 283 /* Wait for ABB LDO to complete transition to new Bias setting */ 284 ret = ti_abb_wait_txdone(dev, abb); 285 if (ret) 286 goto out; 287 288 ret = ti_abb_clear_all_txdone(dev, abb); 289 if (ret) 290 goto out; 291 292 /* 293 * Reset LDO VBB vset override bypass mode 294 * XXX: Do not switch sequence - for bypass, LDO override reset *must* 295 * be performed *after* switch to bypass else VBB glitches. 296 */ 297 if (abb->ldo_base && info->opp_sel == TI_ABB_NOMINAL_OPP) 298 ti_abb_program_ldovbb(dev, abb, info); 299 300 out: 301 return ret; 302 } 303 304 /** 305 * ti_abb_set_voltage_sel() - regulator accessor function to set ABB LDO 306 * @rdev: regulator device 307 * @sel: selector to index into required ABB LDO settings (maps to 308 * regulator descriptor's volt_table) 309 * 310 * Return: 0 on success or appropriate error value when fails 311 */ 312 static int ti_abb_set_voltage_sel(struct regulator_dev *rdev, unsigned sel) 313 { 314 const struct regulator_desc *desc = rdev->desc; 315 struct ti_abb *abb = rdev_get_drvdata(rdev); 316 struct device *dev = &rdev->dev; 317 struct ti_abb_info *info, *oinfo; 318 int ret = 0; 319 320 if (!abb) { 321 dev_err_ratelimited(dev, "%s: No regulator drvdata\n", 322 __func__); 323 return -ENODEV; 324 } 325 326 if (!desc->n_voltages || !abb->info) { 327 dev_err_ratelimited(dev, 328 "%s: No valid voltage table entries?\n", 329 __func__); 330 return -EINVAL; 331 } 332 333 if (sel >= desc->n_voltages) { 334 dev_err(dev, "%s: sel idx(%d) >= n_voltages(%d)\n", __func__, 335 sel, desc->n_voltages); 336 return -EINVAL; 337 } 338 339 /* If we are in the same index as we were, nothing to do here! */ 340 if (sel == abb->current_info_idx) { 341 dev_dbg(dev, "%s: Already at sel=%d\n", __func__, sel); 342 return ret; 343 } 344 345 /* If data is exactly the same, then just update index, no change */ 346 info = &abb->info[sel]; 347 oinfo = &abb->info[abb->current_info_idx]; 348 if (!memcmp(info, oinfo, sizeof(*info))) { 349 dev_dbg(dev, "%s: Same data new idx=%d, old idx=%d\n", __func__, 350 sel, abb->current_info_idx); 351 goto out; 352 } 353 354 ret = ti_abb_set_opp(rdev, abb, info); 355 356 out: 357 if (!ret) 358 abb->current_info_idx = sel; 359 else 360 dev_err_ratelimited(dev, 361 "%s: Volt[%d] idx[%d] mode[%d] Fail(%d)\n", 362 __func__, desc->volt_table[sel], sel, 363 info->opp_sel, ret); 364 return ret; 365 } 366 367 /** 368 * ti_abb_get_voltage_sel() - Regulator accessor to get current ABB LDO setting 369 * @rdev: regulator device 370 * 371 * Return: 0 on success or appropriate error value when fails 372 */ 373 static int ti_abb_get_voltage_sel(struct regulator_dev *rdev) 374 { 375 const struct regulator_desc *desc = rdev->desc; 376 struct ti_abb *abb = rdev_get_drvdata(rdev); 377 struct device *dev = &rdev->dev; 378 379 if (!abb) { 380 dev_err_ratelimited(dev, "%s: No regulator drvdata\n", 381 __func__); 382 return -ENODEV; 383 } 384 385 if (!desc->n_voltages || !abb->info) { 386 dev_err_ratelimited(dev, 387 "%s: No valid voltage table entries?\n", 388 __func__); 389 return -EINVAL; 390 } 391 392 if (abb->current_info_idx >= (int)desc->n_voltages) { 393 dev_err(dev, "%s: Corrupted data? idx(%d) >= n_voltages(%d)\n", 394 __func__, abb->current_info_idx, desc->n_voltages); 395 return -EINVAL; 396 } 397 398 return abb->current_info_idx; 399 } 400 401 /** 402 * ti_abb_init_timings() - setup ABB clock timing for the current platform 403 * @dev: device 404 * @abb: pointer to the abb instance 405 * 406 * Return: 0 if timing is updated, else returns error result. 407 */ 408 static int ti_abb_init_timings(struct device *dev, struct ti_abb *abb) 409 { 410 u32 clock_cycles; 411 u32 clk_rate, sr2_wt_cnt_val, cycle_rate; 412 const struct ti_abb_reg *regs = abb->regs; 413 int ret; 414 char *pname = "ti,settling-time"; 415 416 /* read device tree properties */ 417 ret = of_property_read_u32(dev->of_node, pname, &abb->settling_time); 418 if (ret) { 419 dev_err(dev, "Unable to get property '%s'(%d)\n", pname, ret); 420 return ret; 421 } 422 423 /* ABB LDO cannot be settle in 0 time */ 424 if (!abb->settling_time) { 425 dev_err(dev, "Invalid property:'%s' set as 0!\n", pname); 426 return -EINVAL; 427 } 428 429 pname = "ti,clock-cycles"; 430 ret = of_property_read_u32(dev->of_node, pname, &clock_cycles); 431 if (ret) { 432 dev_err(dev, "Unable to get property '%s'(%d)\n", pname, ret); 433 return ret; 434 } 435 /* ABB LDO cannot be settle in 0 clock cycles */ 436 if (!clock_cycles) { 437 dev_err(dev, "Invalid property:'%s' set as 0!\n", pname); 438 return -EINVAL; 439 } 440 441 abb->clk = devm_clk_get(dev, NULL); 442 if (IS_ERR(abb->clk)) { 443 ret = PTR_ERR(abb->clk); 444 dev_err(dev, "%s: Unable to get clk(%d)\n", __func__, ret); 445 return ret; 446 } 447 448 /* 449 * SR2_WTCNT_VALUE is the settling time for the ABB ldo after a 450 * transition and must be programmed with the correct time at boot. 451 * The value programmed into the register is the number of SYS_CLK 452 * clock cycles that match a given wall time profiled for the ldo. 453 * This value depends on: 454 * settling time of ldo in micro-seconds (varies per OMAP family) 455 * # of clock cycles per SYS_CLK period (varies per OMAP family) 456 * the SYS_CLK frequency in MHz (varies per board) 457 * The formula is: 458 * 459 * ldo settling time (in micro-seconds) 460 * SR2_WTCNT_VALUE = ------------------------------------------ 461 * (# system clock cycles) * (sys_clk period) 462 * 463 * Put another way: 464 * 465 * SR2_WTCNT_VALUE = settling time / (# SYS_CLK cycles / SYS_CLK rate)) 466 * 467 * To avoid dividing by zero multiply both "# clock cycles" and 468 * "settling time" by 10 such that the final result is the one we want. 469 */ 470 471 /* Convert SYS_CLK rate to MHz & prevent divide by zero */ 472 clk_rate = DIV_ROUND_CLOSEST(clk_get_rate(abb->clk), 1000000); 473 474 /* Calculate cycle rate */ 475 cycle_rate = DIV_ROUND_CLOSEST(clock_cycles * 10, clk_rate); 476 477 /* Calulate SR2_WTCNT_VALUE */ 478 sr2_wt_cnt_val = DIV_ROUND_CLOSEST(abb->settling_time * 10, cycle_rate); 479 480 dev_dbg(dev, "%s: Clk_rate=%ld, sr2_cnt=0x%08x\n", __func__, 481 clk_get_rate(abb->clk), sr2_wt_cnt_val); 482 483 ti_abb_rmw(regs->sr2_wtcnt_value_mask, sr2_wt_cnt_val, abb->setup_reg); 484 485 return 0; 486 } 487 488 /** 489 * ti_abb_init_table() - Initialize ABB table from device tree 490 * @dev: device 491 * @abb: pointer to the abb instance 492 * @rinit_data: regulator initdata 493 * 494 * Return: 0 on success or appropriate error value when fails 495 */ 496 static int ti_abb_init_table(struct device *dev, struct ti_abb *abb, 497 struct regulator_init_data *rinit_data) 498 { 499 struct ti_abb_info *info; 500 const u32 num_values = 6; 501 char *pname = "ti,abb_info"; 502 u32 i; 503 unsigned int *volt_table; 504 int num_entries, min_uV = INT_MAX, max_uV = 0; 505 struct regulation_constraints *c = &rinit_data->constraints; 506 507 /* 508 * Each abb_info is a set of n-tuple, where n is num_values, consisting 509 * of voltage and a set of detection logic for ABB information for that 510 * voltage to apply. 511 */ 512 num_entries = of_property_count_u32_elems(dev->of_node, pname); 513 if (num_entries < 0) { 514 dev_err(dev, "No '%s' property?\n", pname); 515 return num_entries; 516 } 517 518 if (!num_entries || (num_entries % num_values)) { 519 dev_err(dev, "All '%s' list entries need %d vals\n", pname, 520 num_values); 521 return -EINVAL; 522 } 523 num_entries /= num_values; 524 525 info = devm_kcalloc(dev, num_entries, sizeof(*info), GFP_KERNEL); 526 if (!info) 527 return -ENOMEM; 528 529 abb->info = info; 530 531 volt_table = devm_kcalloc(dev, num_entries, sizeof(unsigned int), 532 GFP_KERNEL); 533 if (!volt_table) 534 return -ENOMEM; 535 536 abb->rdesc.n_voltages = num_entries; 537 abb->rdesc.volt_table = volt_table; 538 /* We do not know where the OPP voltage is at the moment */ 539 abb->current_info_idx = -EINVAL; 540 541 for (i = 0; i < num_entries; i++, info++, volt_table++) { 542 u32 efuse_offset, rbb_mask, fbb_mask, vset_mask; 543 u32 efuse_val; 544 545 /* NOTE: num_values should equal to entries picked up here */ 546 of_property_read_u32_index(dev->of_node, pname, i * num_values, 547 volt_table); 548 of_property_read_u32_index(dev->of_node, pname, 549 i * num_values + 1, &info->opp_sel); 550 of_property_read_u32_index(dev->of_node, pname, 551 i * num_values + 2, &efuse_offset); 552 of_property_read_u32_index(dev->of_node, pname, 553 i * num_values + 3, &rbb_mask); 554 of_property_read_u32_index(dev->of_node, pname, 555 i * num_values + 4, &fbb_mask); 556 of_property_read_u32_index(dev->of_node, pname, 557 i * num_values + 5, &vset_mask); 558 559 dev_dbg(dev, 560 "[%d]v=%d ABB=%d ef=0x%x rbb=0x%x fbb=0x%x vset=0x%x\n", 561 i, *volt_table, info->opp_sel, efuse_offset, rbb_mask, 562 fbb_mask, vset_mask); 563 564 /* Find min/max for voltage set */ 565 if (min_uV > *volt_table) 566 min_uV = *volt_table; 567 if (max_uV < *volt_table) 568 max_uV = *volt_table; 569 570 if (!abb->efuse_base) { 571 /* Ignore invalid data, but warn to help cleanup */ 572 if (efuse_offset || rbb_mask || fbb_mask || vset_mask) 573 dev_err(dev, "prop '%s': v=%d,bad efuse/mask\n", 574 pname, *volt_table); 575 goto check_abb; 576 } 577 578 efuse_val = readl(abb->efuse_base + efuse_offset); 579 580 /* Use ABB recommendation from Efuse */ 581 if (efuse_val & rbb_mask) 582 info->opp_sel = TI_ABB_SLOW_OPP; 583 else if (efuse_val & fbb_mask) 584 info->opp_sel = TI_ABB_FAST_OPP; 585 else if (rbb_mask || fbb_mask) 586 info->opp_sel = TI_ABB_NOMINAL_OPP; 587 588 dev_dbg(dev, 589 "[%d]v=%d efusev=0x%x final ABB=%d\n", 590 i, *volt_table, efuse_val, info->opp_sel); 591 592 /* Use recommended Vset bits from Efuse */ 593 if (!abb->ldo_base) { 594 if (vset_mask) 595 dev_err(dev, "prop'%s':v=%d vst=%x LDO base?\n", 596 pname, *volt_table, vset_mask); 597 continue; 598 } 599 info->vset = (efuse_val & vset_mask) >> __ffs(vset_mask); 600 dev_dbg(dev, "[%d]v=%d vset=%x\n", i, *volt_table, info->vset); 601 check_abb: 602 switch (info->opp_sel) { 603 case TI_ABB_NOMINAL_OPP: 604 case TI_ABB_FAST_OPP: 605 case TI_ABB_SLOW_OPP: 606 /* Valid values */ 607 break; 608 default: 609 dev_err(dev, "%s:[%d]v=%d, ABB=%d is invalid! Abort!\n", 610 __func__, i, *volt_table, info->opp_sel); 611 return -EINVAL; 612 } 613 } 614 615 /* Setup the min/max voltage constraints from the supported list */ 616 c->min_uV = min_uV; 617 c->max_uV = max_uV; 618 619 return 0; 620 } 621 622 static struct regulator_ops ti_abb_reg_ops = { 623 .list_voltage = regulator_list_voltage_table, 624 625 .set_voltage_sel = ti_abb_set_voltage_sel, 626 .get_voltage_sel = ti_abb_get_voltage_sel, 627 }; 628 629 /* Default ABB block offsets, IF this changes in future, create new one */ 630 static const struct ti_abb_reg abb_regs_v1 = { 631 /* WARNING: registers are wrongly documented in TRM */ 632 .setup_off = 0x04, 633 .control_off = 0x00, 634 635 .sr2_wtcnt_value_mask = (0xff << 8), 636 .fbb_sel_mask = (0x01 << 2), 637 .rbb_sel_mask = (0x01 << 1), 638 .sr2_en_mask = (0x01 << 0), 639 640 .opp_change_mask = (0x01 << 2), 641 .opp_sel_mask = (0x03 << 0), 642 }; 643 644 static const struct ti_abb_reg abb_regs_v2 = { 645 .setup_off = 0x00, 646 .control_off = 0x04, 647 648 .sr2_wtcnt_value_mask = (0xff << 8), 649 .fbb_sel_mask = (0x01 << 2), 650 .rbb_sel_mask = (0x01 << 1), 651 .sr2_en_mask = (0x01 << 0), 652 653 .opp_change_mask = (0x01 << 2), 654 .opp_sel_mask = (0x03 << 0), 655 }; 656 657 static const struct ti_abb_reg abb_regs_generic = { 658 .sr2_wtcnt_value_mask = (0xff << 8), 659 .fbb_sel_mask = (0x01 << 2), 660 .rbb_sel_mask = (0x01 << 1), 661 .sr2_en_mask = (0x01 << 0), 662 663 .opp_change_mask = (0x01 << 2), 664 .opp_sel_mask = (0x03 << 0), 665 }; 666 667 static const struct of_device_id ti_abb_of_match[] = { 668 {.compatible = "ti,abb-v1", .data = &abb_regs_v1}, 669 {.compatible = "ti,abb-v2", .data = &abb_regs_v2}, 670 {.compatible = "ti,abb-v3", .data = &abb_regs_generic}, 671 { }, 672 }; 673 674 MODULE_DEVICE_TABLE(of, ti_abb_of_match); 675 676 /** 677 * ti_abb_probe() - Initialize an ABB ldo instance 678 * @pdev: ABB platform device 679 * 680 * Initializes an individual ABB LDO for required Body-Bias. ABB is used to 681 * addional bias supply to SoC modules for power savings or mandatory stability 682 * configuration at certain Operating Performance Points(OPPs). 683 * 684 * Return: 0 on success or appropriate error value when fails 685 */ 686 static int ti_abb_probe(struct platform_device *pdev) 687 { 688 struct device *dev = &pdev->dev; 689 const struct of_device_id *match; 690 struct resource *res; 691 struct ti_abb *abb; 692 struct regulator_init_data *initdata = NULL; 693 struct regulator_dev *rdev = NULL; 694 struct regulator_desc *desc; 695 struct regulation_constraints *c; 696 struct regulator_config config = { }; 697 char *pname; 698 int ret = 0; 699 700 match = of_match_device(ti_abb_of_match, dev); 701 if (!match) { 702 /* We do not expect this to happen */ 703 dev_err(dev, "%s: Unable to match device\n", __func__); 704 return -ENODEV; 705 } 706 if (!match->data) { 707 dev_err(dev, "%s: Bad data in match\n", __func__); 708 return -EINVAL; 709 } 710 711 abb = devm_kzalloc(dev, sizeof(struct ti_abb), GFP_KERNEL); 712 if (!abb) 713 return -ENOMEM; 714 abb->regs = match->data; 715 716 /* Map ABB resources */ 717 if (abb->regs->setup_off || abb->regs->control_off) { 718 pname = "base-address"; 719 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname); 720 abb->base = devm_ioremap_resource(dev, res); 721 if (IS_ERR(abb->base)) 722 return PTR_ERR(abb->base); 723 724 abb->setup_reg = abb->base + abb->regs->setup_off; 725 abb->control_reg = abb->base + abb->regs->control_off; 726 727 } else { 728 pname = "control-address"; 729 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname); 730 abb->control_reg = devm_ioremap_resource(dev, res); 731 if (IS_ERR(abb->control_reg)) 732 return PTR_ERR(abb->control_reg); 733 734 pname = "setup-address"; 735 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname); 736 abb->setup_reg = devm_ioremap_resource(dev, res); 737 if (IS_ERR(abb->setup_reg)) 738 return PTR_ERR(abb->setup_reg); 739 } 740 741 pname = "int-address"; 742 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname); 743 if (!res) { 744 dev_err(dev, "Missing '%s' IO resource\n", pname); 745 return -ENODEV; 746 } 747 /* 748 * We may have shared interrupt register offsets which are 749 * write-1-to-clear between domains ensuring exclusivity. 750 */ 751 abb->int_base = devm_ioremap_nocache(dev, res->start, 752 resource_size(res)); 753 if (!abb->int_base) { 754 dev_err(dev, "Unable to map '%s'\n", pname); 755 return -ENOMEM; 756 } 757 758 /* Map Optional resources */ 759 pname = "efuse-address"; 760 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname); 761 if (!res) { 762 dev_dbg(dev, "Missing '%s' IO resource\n", pname); 763 ret = -ENODEV; 764 goto skip_opt; 765 } 766 767 /* 768 * We may have shared efuse register offsets which are read-only 769 * between domains 770 */ 771 abb->efuse_base = devm_ioremap_nocache(dev, res->start, 772 resource_size(res)); 773 if (!abb->efuse_base) { 774 dev_err(dev, "Unable to map '%s'\n", pname); 775 return -ENOMEM; 776 } 777 778 pname = "ldo-address"; 779 res = platform_get_resource_byname(pdev, IORESOURCE_MEM, pname); 780 if (!res) { 781 dev_dbg(dev, "Missing '%s' IO resource\n", pname); 782 ret = -ENODEV; 783 goto skip_opt; 784 } 785 abb->ldo_base = devm_ioremap_resource(dev, res); 786 if (IS_ERR(abb->ldo_base)) 787 return PTR_ERR(abb->ldo_base); 788 789 /* IF ldo_base is set, the following are mandatory */ 790 pname = "ti,ldovbb-override-mask"; 791 ret = 792 of_property_read_u32(pdev->dev.of_node, pname, 793 &abb->ldovbb_override_mask); 794 if (ret) { 795 dev_err(dev, "Missing '%s' (%d)\n", pname, ret); 796 return ret; 797 } 798 if (!abb->ldovbb_override_mask) { 799 dev_err(dev, "Invalid property:'%s' set as 0!\n", pname); 800 return -EINVAL; 801 } 802 803 pname = "ti,ldovbb-vset-mask"; 804 ret = 805 of_property_read_u32(pdev->dev.of_node, pname, 806 &abb->ldovbb_vset_mask); 807 if (ret) { 808 dev_err(dev, "Missing '%s' (%d)\n", pname, ret); 809 return ret; 810 } 811 if (!abb->ldovbb_vset_mask) { 812 dev_err(dev, "Invalid property:'%s' set as 0!\n", pname); 813 return -EINVAL; 814 } 815 816 skip_opt: 817 pname = "ti,tranxdone-status-mask"; 818 ret = 819 of_property_read_u32(pdev->dev.of_node, pname, 820 &abb->txdone_mask); 821 if (ret) { 822 dev_err(dev, "Missing '%s' (%d)\n", pname, ret); 823 return ret; 824 } 825 if (!abb->txdone_mask) { 826 dev_err(dev, "Invalid property:'%s' set as 0!\n", pname); 827 return -EINVAL; 828 } 829 830 initdata = of_get_regulator_init_data(dev, pdev->dev.of_node, 831 &abb->rdesc); 832 if (!initdata) { 833 dev_err(dev, "%s: Unable to alloc regulator init data\n", 834 __func__); 835 return -ENOMEM; 836 } 837 838 /* init ABB opp_sel table */ 839 ret = ti_abb_init_table(dev, abb, initdata); 840 if (ret) 841 return ret; 842 843 /* init ABB timing */ 844 ret = ti_abb_init_timings(dev, abb); 845 if (ret) 846 return ret; 847 848 desc = &abb->rdesc; 849 desc->name = dev_name(dev); 850 desc->owner = THIS_MODULE; 851 desc->type = REGULATOR_VOLTAGE; 852 desc->ops = &ti_abb_reg_ops; 853 854 c = &initdata->constraints; 855 if (desc->n_voltages > 1) 856 c->valid_ops_mask |= REGULATOR_CHANGE_VOLTAGE; 857 c->always_on = true; 858 859 config.dev = dev; 860 config.init_data = initdata; 861 config.driver_data = abb; 862 config.of_node = pdev->dev.of_node; 863 864 rdev = devm_regulator_register(dev, desc, &config); 865 if (IS_ERR(rdev)) { 866 ret = PTR_ERR(rdev); 867 dev_err(dev, "%s: failed to register regulator(%d)\n", 868 __func__, ret); 869 return ret; 870 } 871 platform_set_drvdata(pdev, rdev); 872 873 /* Enable the ldo if not already done by bootloader */ 874 ti_abb_rmw(abb->regs->sr2_en_mask, 1, abb->setup_reg); 875 876 return 0; 877 } 878 879 MODULE_ALIAS("platform:ti_abb"); 880 881 static struct platform_driver ti_abb_driver = { 882 .probe = ti_abb_probe, 883 .driver = { 884 .name = "ti_abb", 885 .of_match_table = of_match_ptr(ti_abb_of_match), 886 }, 887 }; 888 module_platform_driver(ti_abb_driver); 889 890 MODULE_DESCRIPTION("Texas Instruments ABB LDO regulator driver"); 891 MODULE_AUTHOR("Texas Instruments Inc."); 892 MODULE_LICENSE("GPL v2"); 893