1 /* 2 * Copyright (c) 2012-2015, The Linux Foundation. All rights reserved. 3 * 4 * This program is free software; you can redistribute it and/or modify 5 * it under the terms of the GNU General Public License version 2 and 6 * only version 2 as published by the Free Software Foundation. 7 * 8 * This program is distributed in the hope that it will be useful, 9 * but WITHOUT ANY WARRANTY; without even the implied warranty of 10 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 11 * GNU General Public License for more details. 12 */ 13 14 #include <linux/module.h> 15 #include <linux/delay.h> 16 #include <linux/err.h> 17 #include <linux/kernel.h> 18 #include <linux/interrupt.h> 19 #include <linux/bitops.h> 20 #include <linux/slab.h> 21 #include <linux/of.h> 22 #include <linux/of_device.h> 23 #include <linux/platform_device.h> 24 #include <linux/ktime.h> 25 #include <linux/regulator/driver.h> 26 #include <linux/regmap.h> 27 #include <linux/list.h> 28 #include <linux/mfd/syscon.h> 29 #include <linux/io.h> 30 31 /* Pin control enable input pins. */ 32 #define SPMI_REGULATOR_PIN_CTRL_ENABLE_NONE 0x00 33 #define SPMI_REGULATOR_PIN_CTRL_ENABLE_EN0 0x01 34 #define SPMI_REGULATOR_PIN_CTRL_ENABLE_EN1 0x02 35 #define SPMI_REGULATOR_PIN_CTRL_ENABLE_EN2 0x04 36 #define SPMI_REGULATOR_PIN_CTRL_ENABLE_EN3 0x08 37 #define SPMI_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT 0x10 38 39 /* Pin control high power mode input pins. */ 40 #define SPMI_REGULATOR_PIN_CTRL_HPM_NONE 0x00 41 #define SPMI_REGULATOR_PIN_CTRL_HPM_EN0 0x01 42 #define SPMI_REGULATOR_PIN_CTRL_HPM_EN1 0x02 43 #define SPMI_REGULATOR_PIN_CTRL_HPM_EN2 0x04 44 #define SPMI_REGULATOR_PIN_CTRL_HPM_EN3 0x08 45 #define SPMI_REGULATOR_PIN_CTRL_HPM_SLEEP_B 0x10 46 #define SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT 0x20 47 48 /* 49 * Used with enable parameters to specify that hardware default register values 50 * should be left unaltered. 51 */ 52 #define SPMI_REGULATOR_USE_HW_DEFAULT 2 53 54 /* Soft start strength of a voltage switch type regulator */ 55 enum spmi_vs_soft_start_str { 56 SPMI_VS_SOFT_START_STR_0P05_UA = 0, 57 SPMI_VS_SOFT_START_STR_0P25_UA, 58 SPMI_VS_SOFT_START_STR_0P55_UA, 59 SPMI_VS_SOFT_START_STR_0P75_UA, 60 SPMI_VS_SOFT_START_STR_HW_DEFAULT, 61 }; 62 63 /** 64 * struct spmi_regulator_init_data - spmi-regulator initialization data 65 * @pin_ctrl_enable: Bit mask specifying which hardware pins should be 66 * used to enable the regulator, if any 67 * Value should be an ORing of 68 * SPMI_REGULATOR_PIN_CTRL_ENABLE_* constants. If 69 * the bit specified by 70 * SPMI_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT is 71 * set, then pin control enable hardware registers 72 * will not be modified. 73 * @pin_ctrl_hpm: Bit mask specifying which hardware pins should be 74 * used to force the regulator into high power 75 * mode, if any 76 * Value should be an ORing of 77 * SPMI_REGULATOR_PIN_CTRL_HPM_* constants. If 78 * the bit specified by 79 * SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT is 80 * set, then pin control mode hardware registers 81 * will not be modified. 82 * @vs_soft_start_strength: This parameter sets the soft start strength for 83 * voltage switch type regulators. Its value 84 * should be one of SPMI_VS_SOFT_START_STR_*. If 85 * its value is SPMI_VS_SOFT_START_STR_HW_DEFAULT, 86 * then the soft start strength will be left at its 87 * default hardware value. 88 */ 89 struct spmi_regulator_init_data { 90 unsigned pin_ctrl_enable; 91 unsigned pin_ctrl_hpm; 92 enum spmi_vs_soft_start_str vs_soft_start_strength; 93 }; 94 95 /* These types correspond to unique register layouts. */ 96 enum spmi_regulator_logical_type { 97 SPMI_REGULATOR_LOGICAL_TYPE_SMPS, 98 SPMI_REGULATOR_LOGICAL_TYPE_LDO, 99 SPMI_REGULATOR_LOGICAL_TYPE_VS, 100 SPMI_REGULATOR_LOGICAL_TYPE_BOOST, 101 SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS, 102 SPMI_REGULATOR_LOGICAL_TYPE_BOOST_BYP, 103 SPMI_REGULATOR_LOGICAL_TYPE_LN_LDO, 104 SPMI_REGULATOR_LOGICAL_TYPE_ULT_LO_SMPS, 105 SPMI_REGULATOR_LOGICAL_TYPE_ULT_HO_SMPS, 106 SPMI_REGULATOR_LOGICAL_TYPE_ULT_LDO, 107 }; 108 109 enum spmi_regulator_type { 110 SPMI_REGULATOR_TYPE_BUCK = 0x03, 111 SPMI_REGULATOR_TYPE_LDO = 0x04, 112 SPMI_REGULATOR_TYPE_VS = 0x05, 113 SPMI_REGULATOR_TYPE_BOOST = 0x1b, 114 SPMI_REGULATOR_TYPE_FTS = 0x1c, 115 SPMI_REGULATOR_TYPE_BOOST_BYP = 0x1f, 116 SPMI_REGULATOR_TYPE_ULT_LDO = 0x21, 117 SPMI_REGULATOR_TYPE_ULT_BUCK = 0x22, 118 }; 119 120 enum spmi_regulator_subtype { 121 SPMI_REGULATOR_SUBTYPE_GP_CTL = 0x08, 122 SPMI_REGULATOR_SUBTYPE_RF_CTL = 0x09, 123 SPMI_REGULATOR_SUBTYPE_N50 = 0x01, 124 SPMI_REGULATOR_SUBTYPE_N150 = 0x02, 125 SPMI_REGULATOR_SUBTYPE_N300 = 0x03, 126 SPMI_REGULATOR_SUBTYPE_N600 = 0x04, 127 SPMI_REGULATOR_SUBTYPE_N1200 = 0x05, 128 SPMI_REGULATOR_SUBTYPE_N600_ST = 0x06, 129 SPMI_REGULATOR_SUBTYPE_N1200_ST = 0x07, 130 SPMI_REGULATOR_SUBTYPE_N900_ST = 0x14, 131 SPMI_REGULATOR_SUBTYPE_N300_ST = 0x15, 132 SPMI_REGULATOR_SUBTYPE_P50 = 0x08, 133 SPMI_REGULATOR_SUBTYPE_P150 = 0x09, 134 SPMI_REGULATOR_SUBTYPE_P300 = 0x0a, 135 SPMI_REGULATOR_SUBTYPE_P600 = 0x0b, 136 SPMI_REGULATOR_SUBTYPE_P1200 = 0x0c, 137 SPMI_REGULATOR_SUBTYPE_LN = 0x10, 138 SPMI_REGULATOR_SUBTYPE_LV_P50 = 0x28, 139 SPMI_REGULATOR_SUBTYPE_LV_P150 = 0x29, 140 SPMI_REGULATOR_SUBTYPE_LV_P300 = 0x2a, 141 SPMI_REGULATOR_SUBTYPE_LV_P600 = 0x2b, 142 SPMI_REGULATOR_SUBTYPE_LV_P1200 = 0x2c, 143 SPMI_REGULATOR_SUBTYPE_LV_P450 = 0x2d, 144 SPMI_REGULATOR_SUBTYPE_LV100 = 0x01, 145 SPMI_REGULATOR_SUBTYPE_LV300 = 0x02, 146 SPMI_REGULATOR_SUBTYPE_MV300 = 0x08, 147 SPMI_REGULATOR_SUBTYPE_MV500 = 0x09, 148 SPMI_REGULATOR_SUBTYPE_HDMI = 0x10, 149 SPMI_REGULATOR_SUBTYPE_OTG = 0x11, 150 SPMI_REGULATOR_SUBTYPE_5V_BOOST = 0x01, 151 SPMI_REGULATOR_SUBTYPE_FTS_CTL = 0x08, 152 SPMI_REGULATOR_SUBTYPE_FTS2p5_CTL = 0x09, 153 SPMI_REGULATOR_SUBTYPE_BB_2A = 0x01, 154 SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL1 = 0x0d, 155 SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL2 = 0x0e, 156 SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL3 = 0x0f, 157 SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL4 = 0x10, 158 }; 159 160 enum spmi_common_regulator_registers { 161 SPMI_COMMON_REG_DIG_MAJOR_REV = 0x01, 162 SPMI_COMMON_REG_TYPE = 0x04, 163 SPMI_COMMON_REG_SUBTYPE = 0x05, 164 SPMI_COMMON_REG_VOLTAGE_RANGE = 0x40, 165 SPMI_COMMON_REG_VOLTAGE_SET = 0x41, 166 SPMI_COMMON_REG_MODE = 0x45, 167 SPMI_COMMON_REG_ENABLE = 0x46, 168 SPMI_COMMON_REG_PULL_DOWN = 0x48, 169 SPMI_COMMON_REG_SOFT_START = 0x4c, 170 SPMI_COMMON_REG_STEP_CTRL = 0x61, 171 }; 172 173 enum spmi_vs_registers { 174 SPMI_VS_REG_OCP = 0x4a, 175 SPMI_VS_REG_SOFT_START = 0x4c, 176 }; 177 178 enum spmi_boost_registers { 179 SPMI_BOOST_REG_CURRENT_LIMIT = 0x4a, 180 }; 181 182 enum spmi_boost_byp_registers { 183 SPMI_BOOST_BYP_REG_CURRENT_LIMIT = 0x4b, 184 }; 185 186 enum spmi_saw3_registers { 187 SAW3_SECURE = 0x00, 188 SAW3_ID = 0x04, 189 SAW3_SPM_STS = 0x0C, 190 SAW3_AVS_STS = 0x10, 191 SAW3_PMIC_STS = 0x14, 192 SAW3_RST = 0x18, 193 SAW3_VCTL = 0x1C, 194 SAW3_AVS_CTL = 0x20, 195 SAW3_AVS_LIMIT = 0x24, 196 SAW3_AVS_DLY = 0x28, 197 SAW3_AVS_HYSTERESIS = 0x2C, 198 SAW3_SPM_STS2 = 0x38, 199 SAW3_SPM_PMIC_DATA_3 = 0x4C, 200 SAW3_VERSION = 0xFD0, 201 }; 202 203 /* Used for indexing into ctrl_reg. These are offets from 0x40 */ 204 enum spmi_common_control_register_index { 205 SPMI_COMMON_IDX_VOLTAGE_RANGE = 0, 206 SPMI_COMMON_IDX_VOLTAGE_SET = 1, 207 SPMI_COMMON_IDX_MODE = 5, 208 SPMI_COMMON_IDX_ENABLE = 6, 209 }; 210 211 /* Common regulator control register layout */ 212 #define SPMI_COMMON_ENABLE_MASK 0x80 213 #define SPMI_COMMON_ENABLE 0x80 214 #define SPMI_COMMON_DISABLE 0x00 215 #define SPMI_COMMON_ENABLE_FOLLOW_HW_EN3_MASK 0x08 216 #define SPMI_COMMON_ENABLE_FOLLOW_HW_EN2_MASK 0x04 217 #define SPMI_COMMON_ENABLE_FOLLOW_HW_EN1_MASK 0x02 218 #define SPMI_COMMON_ENABLE_FOLLOW_HW_EN0_MASK 0x01 219 #define SPMI_COMMON_ENABLE_FOLLOW_ALL_MASK 0x0f 220 221 /* Common regulator mode register layout */ 222 #define SPMI_COMMON_MODE_HPM_MASK 0x80 223 #define SPMI_COMMON_MODE_AUTO_MASK 0x40 224 #define SPMI_COMMON_MODE_BYPASS_MASK 0x20 225 #define SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK 0x10 226 #define SPMI_COMMON_MODE_FOLLOW_HW_EN3_MASK 0x08 227 #define SPMI_COMMON_MODE_FOLLOW_HW_EN2_MASK 0x04 228 #define SPMI_COMMON_MODE_FOLLOW_HW_EN1_MASK 0x02 229 #define SPMI_COMMON_MODE_FOLLOW_HW_EN0_MASK 0x01 230 #define SPMI_COMMON_MODE_FOLLOW_ALL_MASK 0x1f 231 232 /* Common regulator pull down control register layout */ 233 #define SPMI_COMMON_PULL_DOWN_ENABLE_MASK 0x80 234 235 /* LDO regulator current limit control register layout */ 236 #define SPMI_LDO_CURRENT_LIMIT_ENABLE_MASK 0x80 237 238 /* LDO regulator soft start control register layout */ 239 #define SPMI_LDO_SOFT_START_ENABLE_MASK 0x80 240 241 /* VS regulator over current protection control register layout */ 242 #define SPMI_VS_OCP_OVERRIDE 0x01 243 #define SPMI_VS_OCP_NO_OVERRIDE 0x00 244 245 /* VS regulator soft start control register layout */ 246 #define SPMI_VS_SOFT_START_ENABLE_MASK 0x80 247 #define SPMI_VS_SOFT_START_SEL_MASK 0x03 248 249 /* Boost regulator current limit control register layout */ 250 #define SPMI_BOOST_CURRENT_LIMIT_ENABLE_MASK 0x80 251 #define SPMI_BOOST_CURRENT_LIMIT_MASK 0x07 252 253 #define SPMI_VS_OCP_DEFAULT_MAX_RETRIES 10 254 #define SPMI_VS_OCP_DEFAULT_RETRY_DELAY_MS 30 255 #define SPMI_VS_OCP_FALL_DELAY_US 90 256 #define SPMI_VS_OCP_FAULT_DELAY_US 20000 257 258 #define SPMI_FTSMPS_STEP_CTRL_STEP_MASK 0x18 259 #define SPMI_FTSMPS_STEP_CTRL_STEP_SHIFT 3 260 #define SPMI_FTSMPS_STEP_CTRL_DELAY_MASK 0x07 261 #define SPMI_FTSMPS_STEP_CTRL_DELAY_SHIFT 0 262 263 /* Clock rate in kHz of the FTSMPS regulator reference clock. */ 264 #define SPMI_FTSMPS_CLOCK_RATE 19200 265 266 /* Minimum voltage stepper delay for each step. */ 267 #define SPMI_FTSMPS_STEP_DELAY 8 268 #define SPMI_DEFAULT_STEP_DELAY 20 269 270 /* 271 * The ratio SPMI_FTSMPS_STEP_MARGIN_NUM/SPMI_FTSMPS_STEP_MARGIN_DEN is used to 272 * adjust the step rate in order to account for oscillator variance. 273 */ 274 #define SPMI_FTSMPS_STEP_MARGIN_NUM 4 275 #define SPMI_FTSMPS_STEP_MARGIN_DEN 5 276 277 /* VSET value to decide the range of ULT SMPS */ 278 #define ULT_SMPS_RANGE_SPLIT 0x60 279 280 /** 281 * struct spmi_voltage_range - regulator set point voltage mapping description 282 * @min_uV: Minimum programmable output voltage resulting from 283 * set point register value 0x00 284 * @max_uV: Maximum programmable output voltage 285 * @step_uV: Output voltage increase resulting from the set point 286 * register value increasing by 1 287 * @set_point_min_uV: Minimum allowed voltage 288 * @set_point_max_uV: Maximum allowed voltage. This may be tweaked in order 289 * to pick which range should be used in the case of 290 * overlapping set points. 291 * @n_voltages: Number of preferred voltage set points present in this 292 * range 293 * @range_sel: Voltage range register value corresponding to this range 294 * 295 * The following relationships must be true for the values used in this struct: 296 * (max_uV - min_uV) % step_uV == 0 297 * (set_point_min_uV - min_uV) % step_uV == 0* 298 * (set_point_max_uV - min_uV) % step_uV == 0* 299 * n_voltages = (set_point_max_uV - set_point_min_uV) / step_uV + 1 300 * 301 * *Note, set_point_min_uV == set_point_max_uV == 0 is allowed in order to 302 * specify that the voltage range has meaning, but is not preferred. 303 */ 304 struct spmi_voltage_range { 305 int min_uV; 306 int max_uV; 307 int step_uV; 308 int set_point_min_uV; 309 int set_point_max_uV; 310 unsigned n_voltages; 311 u8 range_sel; 312 }; 313 314 /* 315 * The ranges specified in the spmi_voltage_set_points struct must be listed 316 * so that range[i].set_point_max_uV < range[i+1].set_point_min_uV. 317 */ 318 struct spmi_voltage_set_points { 319 struct spmi_voltage_range *range; 320 int count; 321 unsigned n_voltages; 322 }; 323 324 struct spmi_regulator { 325 struct regulator_desc desc; 326 struct device *dev; 327 struct delayed_work ocp_work; 328 struct regmap *regmap; 329 struct spmi_voltage_set_points *set_points; 330 enum spmi_regulator_logical_type logical_type; 331 int ocp_irq; 332 int ocp_count; 333 int ocp_max_retries; 334 int ocp_retry_delay_ms; 335 int hpm_min_load; 336 int slew_rate; 337 ktime_t vs_enable_time; 338 u16 base; 339 struct list_head node; 340 }; 341 342 struct spmi_regulator_mapping { 343 enum spmi_regulator_type type; 344 enum spmi_regulator_subtype subtype; 345 enum spmi_regulator_logical_type logical_type; 346 u32 revision_min; 347 u32 revision_max; 348 struct regulator_ops *ops; 349 struct spmi_voltage_set_points *set_points; 350 int hpm_min_load; 351 }; 352 353 struct spmi_regulator_data { 354 const char *name; 355 u16 base; 356 const char *supply; 357 const char *ocp; 358 u16 force_type; 359 }; 360 361 #define SPMI_VREG(_type, _subtype, _dig_major_min, _dig_major_max, \ 362 _logical_type, _ops_val, _set_points_val, _hpm_min_load) \ 363 { \ 364 .type = SPMI_REGULATOR_TYPE_##_type, \ 365 .subtype = SPMI_REGULATOR_SUBTYPE_##_subtype, \ 366 .revision_min = _dig_major_min, \ 367 .revision_max = _dig_major_max, \ 368 .logical_type = SPMI_REGULATOR_LOGICAL_TYPE_##_logical_type, \ 369 .ops = &spmi_##_ops_val##_ops, \ 370 .set_points = &_set_points_val##_set_points, \ 371 .hpm_min_load = _hpm_min_load, \ 372 } 373 374 #define SPMI_VREG_VS(_subtype, _dig_major_min, _dig_major_max) \ 375 { \ 376 .type = SPMI_REGULATOR_TYPE_VS, \ 377 .subtype = SPMI_REGULATOR_SUBTYPE_##_subtype, \ 378 .revision_min = _dig_major_min, \ 379 .revision_max = _dig_major_max, \ 380 .logical_type = SPMI_REGULATOR_LOGICAL_TYPE_VS, \ 381 .ops = &spmi_vs_ops, \ 382 } 383 384 #define SPMI_VOLTAGE_RANGE(_range_sel, _min_uV, _set_point_min_uV, \ 385 _set_point_max_uV, _max_uV, _step_uV) \ 386 { \ 387 .min_uV = _min_uV, \ 388 .max_uV = _max_uV, \ 389 .set_point_min_uV = _set_point_min_uV, \ 390 .set_point_max_uV = _set_point_max_uV, \ 391 .step_uV = _step_uV, \ 392 .range_sel = _range_sel, \ 393 } 394 395 #define DEFINE_SPMI_SET_POINTS(name) \ 396 struct spmi_voltage_set_points name##_set_points = { \ 397 .range = name##_ranges, \ 398 .count = ARRAY_SIZE(name##_ranges), \ 399 } 400 401 /* 402 * These tables contain the physically available PMIC regulator voltage setpoint 403 * ranges. Where two ranges overlap in hardware, one of the ranges is trimmed 404 * to ensure that the setpoints available to software are monotonically 405 * increasing and unique. The set_voltage callback functions expect these 406 * properties to hold. 407 */ 408 static struct spmi_voltage_range pldo_ranges[] = { 409 SPMI_VOLTAGE_RANGE(2, 750000, 750000, 1537500, 1537500, 12500), 410 SPMI_VOLTAGE_RANGE(3, 1500000, 1550000, 3075000, 3075000, 25000), 411 SPMI_VOLTAGE_RANGE(4, 1750000, 3100000, 4900000, 4900000, 50000), 412 }; 413 414 static struct spmi_voltage_range nldo1_ranges[] = { 415 SPMI_VOLTAGE_RANGE(2, 750000, 750000, 1537500, 1537500, 12500), 416 }; 417 418 static struct spmi_voltage_range nldo2_ranges[] = { 419 SPMI_VOLTAGE_RANGE(0, 375000, 0, 0, 1537500, 12500), 420 SPMI_VOLTAGE_RANGE(1, 375000, 375000, 768750, 768750, 6250), 421 SPMI_VOLTAGE_RANGE(2, 750000, 775000, 1537500, 1537500, 12500), 422 }; 423 424 static struct spmi_voltage_range nldo3_ranges[] = { 425 SPMI_VOLTAGE_RANGE(0, 375000, 375000, 1537500, 1537500, 12500), 426 SPMI_VOLTAGE_RANGE(1, 375000, 0, 0, 1537500, 12500), 427 SPMI_VOLTAGE_RANGE(2, 750000, 0, 0, 1537500, 12500), 428 }; 429 430 static struct spmi_voltage_range ln_ldo_ranges[] = { 431 SPMI_VOLTAGE_RANGE(1, 690000, 690000, 1110000, 1110000, 60000), 432 SPMI_VOLTAGE_RANGE(0, 1380000, 1380000, 2220000, 2220000, 120000), 433 }; 434 435 static struct spmi_voltage_range smps_ranges[] = { 436 SPMI_VOLTAGE_RANGE(0, 375000, 375000, 1562500, 1562500, 12500), 437 SPMI_VOLTAGE_RANGE(1, 1550000, 1575000, 3125000, 3125000, 25000), 438 }; 439 440 static struct spmi_voltage_range ftsmps_ranges[] = { 441 SPMI_VOLTAGE_RANGE(0, 0, 350000, 1275000, 1275000, 5000), 442 SPMI_VOLTAGE_RANGE(1, 0, 1280000, 2040000, 2040000, 10000), 443 }; 444 445 static struct spmi_voltage_range ftsmps2p5_ranges[] = { 446 SPMI_VOLTAGE_RANGE(0, 80000, 350000, 1355000, 1355000, 5000), 447 SPMI_VOLTAGE_RANGE(1, 160000, 1360000, 2200000, 2200000, 10000), 448 }; 449 450 static struct spmi_voltage_range boost_ranges[] = { 451 SPMI_VOLTAGE_RANGE(0, 4000000, 4000000, 5550000, 5550000, 50000), 452 }; 453 454 static struct spmi_voltage_range boost_byp_ranges[] = { 455 SPMI_VOLTAGE_RANGE(0, 2500000, 2500000, 5200000, 5650000, 50000), 456 }; 457 458 static struct spmi_voltage_range ult_lo_smps_ranges[] = { 459 SPMI_VOLTAGE_RANGE(0, 375000, 375000, 1562500, 1562500, 12500), 460 SPMI_VOLTAGE_RANGE(1, 750000, 0, 0, 1525000, 25000), 461 }; 462 463 static struct spmi_voltage_range ult_ho_smps_ranges[] = { 464 SPMI_VOLTAGE_RANGE(0, 1550000, 1550000, 2325000, 2325000, 25000), 465 }; 466 467 static struct spmi_voltage_range ult_nldo_ranges[] = { 468 SPMI_VOLTAGE_RANGE(0, 375000, 375000, 1537500, 1537500, 12500), 469 }; 470 471 static struct spmi_voltage_range ult_pldo_ranges[] = { 472 SPMI_VOLTAGE_RANGE(0, 1750000, 1750000, 3337500, 3337500, 12500), 473 }; 474 475 static DEFINE_SPMI_SET_POINTS(pldo); 476 static DEFINE_SPMI_SET_POINTS(nldo1); 477 static DEFINE_SPMI_SET_POINTS(nldo2); 478 static DEFINE_SPMI_SET_POINTS(nldo3); 479 static DEFINE_SPMI_SET_POINTS(ln_ldo); 480 static DEFINE_SPMI_SET_POINTS(smps); 481 static DEFINE_SPMI_SET_POINTS(ftsmps); 482 static DEFINE_SPMI_SET_POINTS(ftsmps2p5); 483 static DEFINE_SPMI_SET_POINTS(boost); 484 static DEFINE_SPMI_SET_POINTS(boost_byp); 485 static DEFINE_SPMI_SET_POINTS(ult_lo_smps); 486 static DEFINE_SPMI_SET_POINTS(ult_ho_smps); 487 static DEFINE_SPMI_SET_POINTS(ult_nldo); 488 static DEFINE_SPMI_SET_POINTS(ult_pldo); 489 490 static inline int spmi_vreg_read(struct spmi_regulator *vreg, u16 addr, u8 *buf, 491 int len) 492 { 493 return regmap_bulk_read(vreg->regmap, vreg->base + addr, buf, len); 494 } 495 496 static inline int spmi_vreg_write(struct spmi_regulator *vreg, u16 addr, 497 u8 *buf, int len) 498 { 499 return regmap_bulk_write(vreg->regmap, vreg->base + addr, buf, len); 500 } 501 502 static int spmi_vreg_update_bits(struct spmi_regulator *vreg, u16 addr, u8 val, 503 u8 mask) 504 { 505 return regmap_update_bits(vreg->regmap, vreg->base + addr, mask, val); 506 } 507 508 static int spmi_regulator_vs_enable(struct regulator_dev *rdev) 509 { 510 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 511 512 if (vreg->ocp_irq) { 513 vreg->ocp_count = 0; 514 vreg->vs_enable_time = ktime_get(); 515 } 516 517 return regulator_enable_regmap(rdev); 518 } 519 520 static int spmi_regulator_vs_ocp(struct regulator_dev *rdev) 521 { 522 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 523 u8 reg = SPMI_VS_OCP_OVERRIDE; 524 525 return spmi_vreg_write(vreg, SPMI_VS_REG_OCP, ®, 1); 526 } 527 528 static int spmi_regulator_select_voltage(struct spmi_regulator *vreg, 529 int min_uV, int max_uV) 530 { 531 const struct spmi_voltage_range *range; 532 int uV = min_uV; 533 int lim_min_uV, lim_max_uV, i, range_id, range_max_uV; 534 int selector, voltage_sel; 535 536 /* Check if request voltage is outside of physically settable range. */ 537 lim_min_uV = vreg->set_points->range[0].set_point_min_uV; 538 lim_max_uV = 539 vreg->set_points->range[vreg->set_points->count - 1].set_point_max_uV; 540 541 if (uV < lim_min_uV && max_uV >= lim_min_uV) 542 uV = lim_min_uV; 543 544 if (uV < lim_min_uV || uV > lim_max_uV) { 545 dev_err(vreg->dev, 546 "request v=[%d, %d] is outside possible v=[%d, %d]\n", 547 min_uV, max_uV, lim_min_uV, lim_max_uV); 548 return -EINVAL; 549 } 550 551 /* Find the range which uV is inside of. */ 552 for (i = vreg->set_points->count - 1; i > 0; i--) { 553 range_max_uV = vreg->set_points->range[i - 1].set_point_max_uV; 554 if (uV > range_max_uV && range_max_uV > 0) 555 break; 556 } 557 558 range_id = i; 559 range = &vreg->set_points->range[range_id]; 560 561 /* 562 * Force uV to be an allowed set point by applying a ceiling function to 563 * the uV value. 564 */ 565 voltage_sel = DIV_ROUND_UP(uV - range->min_uV, range->step_uV); 566 uV = voltage_sel * range->step_uV + range->min_uV; 567 568 if (uV > max_uV) { 569 dev_err(vreg->dev, 570 "request v=[%d, %d] cannot be met by any set point; " 571 "next set point: %d\n", 572 min_uV, max_uV, uV); 573 return -EINVAL; 574 } 575 576 selector = 0; 577 for (i = 0; i < range_id; i++) 578 selector += vreg->set_points->range[i].n_voltages; 579 selector += (uV - range->set_point_min_uV) / range->step_uV; 580 581 return selector; 582 } 583 584 static int spmi_sw_selector_to_hw(struct spmi_regulator *vreg, 585 unsigned selector, u8 *range_sel, 586 u8 *voltage_sel) 587 { 588 const struct spmi_voltage_range *range, *end; 589 unsigned offset; 590 591 range = vreg->set_points->range; 592 end = range + vreg->set_points->count; 593 594 for (; range < end; range++) { 595 if (selector < range->n_voltages) { 596 /* 597 * hardware selectors between set point min and real 598 * min are invalid so we ignore them 599 */ 600 offset = range->set_point_min_uV - range->min_uV; 601 offset /= range->step_uV; 602 *voltage_sel = selector + offset; 603 *range_sel = range->range_sel; 604 return 0; 605 } 606 607 selector -= range->n_voltages; 608 } 609 610 return -EINVAL; 611 } 612 613 static int spmi_hw_selector_to_sw(struct spmi_regulator *vreg, u8 hw_sel, 614 const struct spmi_voltage_range *range) 615 { 616 unsigned sw_sel = 0; 617 unsigned offset, max_hw_sel; 618 const struct spmi_voltage_range *r = vreg->set_points->range; 619 const struct spmi_voltage_range *end = r + vreg->set_points->count; 620 621 for (; r < end; r++) { 622 if (r == range && range->n_voltages) { 623 /* 624 * hardware selectors between set point min and real 625 * min and between set point max and real max are 626 * invalid so we return an error if they're 627 * programmed into the hardware 628 */ 629 offset = range->set_point_min_uV - range->min_uV; 630 offset /= range->step_uV; 631 if (hw_sel < offset) 632 return -EINVAL; 633 634 max_hw_sel = range->set_point_max_uV - range->min_uV; 635 max_hw_sel /= range->step_uV; 636 if (hw_sel > max_hw_sel) 637 return -EINVAL; 638 639 return sw_sel + hw_sel - offset; 640 } 641 sw_sel += r->n_voltages; 642 } 643 644 return -EINVAL; 645 } 646 647 static const struct spmi_voltage_range * 648 spmi_regulator_find_range(struct spmi_regulator *vreg) 649 { 650 u8 range_sel; 651 const struct spmi_voltage_range *range, *end; 652 653 range = vreg->set_points->range; 654 end = range + vreg->set_points->count; 655 656 spmi_vreg_read(vreg, SPMI_COMMON_REG_VOLTAGE_RANGE, &range_sel, 1); 657 658 for (; range < end; range++) 659 if (range->range_sel == range_sel) 660 return range; 661 662 return NULL; 663 } 664 665 static int spmi_regulator_select_voltage_same_range(struct spmi_regulator *vreg, 666 int min_uV, int max_uV) 667 { 668 const struct spmi_voltage_range *range; 669 int uV = min_uV; 670 int i, selector; 671 672 range = spmi_regulator_find_range(vreg); 673 if (!range) 674 goto different_range; 675 676 if (uV < range->min_uV && max_uV >= range->min_uV) 677 uV = range->min_uV; 678 679 if (uV < range->min_uV || uV > range->max_uV) { 680 /* Current range doesn't support the requested voltage. */ 681 goto different_range; 682 } 683 684 /* 685 * Force uV to be an allowed set point by applying a ceiling function to 686 * the uV value. 687 */ 688 uV = DIV_ROUND_UP(uV - range->min_uV, range->step_uV); 689 uV = uV * range->step_uV + range->min_uV; 690 691 if (uV > max_uV) { 692 /* 693 * No set point in the current voltage range is within the 694 * requested min_uV to max_uV range. 695 */ 696 goto different_range; 697 } 698 699 selector = 0; 700 for (i = 0; i < vreg->set_points->count; i++) { 701 if (uV >= vreg->set_points->range[i].set_point_min_uV 702 && uV <= vreg->set_points->range[i].set_point_max_uV) { 703 selector += 704 (uV - vreg->set_points->range[i].set_point_min_uV) 705 / vreg->set_points->range[i].step_uV; 706 break; 707 } 708 709 selector += vreg->set_points->range[i].n_voltages; 710 } 711 712 if (selector >= vreg->set_points->n_voltages) 713 goto different_range; 714 715 return selector; 716 717 different_range: 718 return spmi_regulator_select_voltage(vreg, min_uV, max_uV); 719 } 720 721 static int spmi_regulator_common_map_voltage(struct regulator_dev *rdev, 722 int min_uV, int max_uV) 723 { 724 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 725 726 /* 727 * Favor staying in the current voltage range if possible. This avoids 728 * voltage spikes that occur when changing the voltage range. 729 */ 730 return spmi_regulator_select_voltage_same_range(vreg, min_uV, max_uV); 731 } 732 733 static int 734 spmi_regulator_common_set_voltage(struct regulator_dev *rdev, unsigned selector) 735 { 736 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 737 int ret; 738 u8 buf[2]; 739 u8 range_sel, voltage_sel; 740 741 ret = spmi_sw_selector_to_hw(vreg, selector, &range_sel, &voltage_sel); 742 if (ret) 743 return ret; 744 745 buf[0] = range_sel; 746 buf[1] = voltage_sel; 747 return spmi_vreg_write(vreg, SPMI_COMMON_REG_VOLTAGE_RANGE, buf, 2); 748 } 749 750 static int spmi_regulator_set_voltage_time_sel(struct regulator_dev *rdev, 751 unsigned int old_selector, unsigned int new_selector) 752 { 753 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 754 const struct spmi_voltage_range *range; 755 int diff_uV; 756 757 range = spmi_regulator_find_range(vreg); 758 if (!range) 759 return -EINVAL; 760 761 diff_uV = abs(new_selector - old_selector) * range->step_uV; 762 763 return DIV_ROUND_UP(diff_uV, vreg->slew_rate); 764 } 765 766 static int spmi_regulator_common_get_voltage(struct regulator_dev *rdev) 767 { 768 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 769 const struct spmi_voltage_range *range; 770 u8 voltage_sel; 771 772 spmi_vreg_read(vreg, SPMI_COMMON_REG_VOLTAGE_SET, &voltage_sel, 1); 773 774 range = spmi_regulator_find_range(vreg); 775 if (!range) 776 return -EINVAL; 777 778 return spmi_hw_selector_to_sw(vreg, voltage_sel, range); 779 } 780 781 static int spmi_regulator_single_map_voltage(struct regulator_dev *rdev, 782 int min_uV, int max_uV) 783 { 784 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 785 786 return spmi_regulator_select_voltage(vreg, min_uV, max_uV); 787 } 788 789 static int spmi_regulator_single_range_set_voltage(struct regulator_dev *rdev, 790 unsigned selector) 791 { 792 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 793 u8 sel = selector; 794 795 /* 796 * Certain types of regulators do not have a range select register so 797 * only voltage set register needs to be written. 798 */ 799 return spmi_vreg_write(vreg, SPMI_COMMON_REG_VOLTAGE_SET, &sel, 1); 800 } 801 802 static int spmi_regulator_single_range_get_voltage(struct regulator_dev *rdev) 803 { 804 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 805 u8 selector; 806 int ret; 807 808 ret = spmi_vreg_read(vreg, SPMI_COMMON_REG_VOLTAGE_SET, &selector, 1); 809 if (ret) 810 return ret; 811 812 return selector; 813 } 814 815 static int spmi_regulator_ult_lo_smps_set_voltage(struct regulator_dev *rdev, 816 unsigned selector) 817 { 818 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 819 int ret; 820 u8 range_sel, voltage_sel; 821 822 ret = spmi_sw_selector_to_hw(vreg, selector, &range_sel, &voltage_sel); 823 if (ret) 824 return ret; 825 826 /* 827 * Calculate VSET based on range 828 * In case of range 0: voltage_sel is a 7 bit value, can be written 829 * witout any modification. 830 * In case of range 1: voltage_sel is a 5 bit value, bits[7-5] set to 831 * [011]. 832 */ 833 if (range_sel == 1) 834 voltage_sel |= ULT_SMPS_RANGE_SPLIT; 835 836 return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_VOLTAGE_SET, 837 voltage_sel, 0xff); 838 } 839 840 static int spmi_regulator_ult_lo_smps_get_voltage(struct regulator_dev *rdev) 841 { 842 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 843 const struct spmi_voltage_range *range; 844 u8 voltage_sel; 845 846 spmi_vreg_read(vreg, SPMI_COMMON_REG_VOLTAGE_SET, &voltage_sel, 1); 847 848 range = spmi_regulator_find_range(vreg); 849 if (!range) 850 return -EINVAL; 851 852 if (range->range_sel == 1) 853 voltage_sel &= ~ULT_SMPS_RANGE_SPLIT; 854 855 return spmi_hw_selector_to_sw(vreg, voltage_sel, range); 856 } 857 858 static int spmi_regulator_common_list_voltage(struct regulator_dev *rdev, 859 unsigned selector) 860 { 861 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 862 int uV = 0; 863 int i; 864 865 if (selector >= vreg->set_points->n_voltages) 866 return 0; 867 868 for (i = 0; i < vreg->set_points->count; i++) { 869 if (selector < vreg->set_points->range[i].n_voltages) { 870 uV = selector * vreg->set_points->range[i].step_uV 871 + vreg->set_points->range[i].set_point_min_uV; 872 break; 873 } 874 875 selector -= vreg->set_points->range[i].n_voltages; 876 } 877 878 return uV; 879 } 880 881 static int 882 spmi_regulator_common_set_bypass(struct regulator_dev *rdev, bool enable) 883 { 884 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 885 u8 mask = SPMI_COMMON_MODE_BYPASS_MASK; 886 u8 val = 0; 887 888 if (enable) 889 val = mask; 890 891 return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_MODE, val, mask); 892 } 893 894 static int 895 spmi_regulator_common_get_bypass(struct regulator_dev *rdev, bool *enable) 896 { 897 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 898 u8 val; 899 int ret; 900 901 ret = spmi_vreg_read(vreg, SPMI_COMMON_REG_MODE, &val, 1); 902 *enable = val & SPMI_COMMON_MODE_BYPASS_MASK; 903 904 return ret; 905 } 906 907 static unsigned int spmi_regulator_common_get_mode(struct regulator_dev *rdev) 908 { 909 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 910 u8 reg; 911 912 spmi_vreg_read(vreg, SPMI_COMMON_REG_MODE, ®, 1); 913 914 if (reg & SPMI_COMMON_MODE_HPM_MASK) 915 return REGULATOR_MODE_NORMAL; 916 917 if (reg & SPMI_COMMON_MODE_AUTO_MASK) 918 return REGULATOR_MODE_FAST; 919 920 return REGULATOR_MODE_IDLE; 921 } 922 923 static int 924 spmi_regulator_common_set_mode(struct regulator_dev *rdev, unsigned int mode) 925 { 926 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 927 u8 mask = SPMI_COMMON_MODE_HPM_MASK | SPMI_COMMON_MODE_AUTO_MASK; 928 u8 val = 0; 929 930 if (mode == REGULATOR_MODE_NORMAL) 931 val = SPMI_COMMON_MODE_HPM_MASK; 932 else if (mode == REGULATOR_MODE_FAST) 933 val = SPMI_COMMON_MODE_AUTO_MASK; 934 935 return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_MODE, val, mask); 936 } 937 938 static int 939 spmi_regulator_common_set_load(struct regulator_dev *rdev, int load_uA) 940 { 941 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 942 unsigned int mode; 943 944 if (load_uA >= vreg->hpm_min_load) 945 mode = REGULATOR_MODE_NORMAL; 946 else 947 mode = REGULATOR_MODE_IDLE; 948 949 return spmi_regulator_common_set_mode(rdev, mode); 950 } 951 952 static int spmi_regulator_common_set_pull_down(struct regulator_dev *rdev) 953 { 954 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 955 unsigned int mask = SPMI_COMMON_PULL_DOWN_ENABLE_MASK; 956 957 return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_PULL_DOWN, 958 mask, mask); 959 } 960 961 static int spmi_regulator_common_set_soft_start(struct regulator_dev *rdev) 962 { 963 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 964 unsigned int mask = SPMI_LDO_SOFT_START_ENABLE_MASK; 965 966 return spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_SOFT_START, 967 mask, mask); 968 } 969 970 static int spmi_regulator_set_ilim(struct regulator_dev *rdev, int ilim_uA) 971 { 972 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 973 enum spmi_regulator_logical_type type = vreg->logical_type; 974 unsigned int current_reg; 975 u8 reg; 976 u8 mask = SPMI_BOOST_CURRENT_LIMIT_MASK | 977 SPMI_BOOST_CURRENT_LIMIT_ENABLE_MASK; 978 int max = (SPMI_BOOST_CURRENT_LIMIT_MASK + 1) * 500; 979 980 if (type == SPMI_REGULATOR_LOGICAL_TYPE_BOOST) 981 current_reg = SPMI_BOOST_REG_CURRENT_LIMIT; 982 else 983 current_reg = SPMI_BOOST_BYP_REG_CURRENT_LIMIT; 984 985 if (ilim_uA > max || ilim_uA <= 0) 986 return -EINVAL; 987 988 reg = (ilim_uA - 1) / 500; 989 reg |= SPMI_BOOST_CURRENT_LIMIT_ENABLE_MASK; 990 991 return spmi_vreg_update_bits(vreg, current_reg, reg, mask); 992 } 993 994 static int spmi_regulator_vs_clear_ocp(struct spmi_regulator *vreg) 995 { 996 int ret; 997 998 ret = spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_ENABLE, 999 SPMI_COMMON_DISABLE, SPMI_COMMON_ENABLE_MASK); 1000 1001 vreg->vs_enable_time = ktime_get(); 1002 1003 ret = spmi_vreg_update_bits(vreg, SPMI_COMMON_REG_ENABLE, 1004 SPMI_COMMON_ENABLE, SPMI_COMMON_ENABLE_MASK); 1005 1006 return ret; 1007 } 1008 1009 static void spmi_regulator_vs_ocp_work(struct work_struct *work) 1010 { 1011 struct delayed_work *dwork = to_delayed_work(work); 1012 struct spmi_regulator *vreg 1013 = container_of(dwork, struct spmi_regulator, ocp_work); 1014 1015 spmi_regulator_vs_clear_ocp(vreg); 1016 } 1017 1018 static irqreturn_t spmi_regulator_vs_ocp_isr(int irq, void *data) 1019 { 1020 struct spmi_regulator *vreg = data; 1021 ktime_t ocp_irq_time; 1022 s64 ocp_trigger_delay_us; 1023 1024 ocp_irq_time = ktime_get(); 1025 ocp_trigger_delay_us = ktime_us_delta(ocp_irq_time, 1026 vreg->vs_enable_time); 1027 1028 /* 1029 * Reset the OCP count if there is a large delay between switch enable 1030 * and when OCP triggers. This is indicative of a hotplug event as 1031 * opposed to a fault. 1032 */ 1033 if (ocp_trigger_delay_us > SPMI_VS_OCP_FAULT_DELAY_US) 1034 vreg->ocp_count = 0; 1035 1036 /* Wait for switch output to settle back to 0 V after OCP triggered. */ 1037 udelay(SPMI_VS_OCP_FALL_DELAY_US); 1038 1039 vreg->ocp_count++; 1040 1041 if (vreg->ocp_count == 1) { 1042 /* Immediately clear the over current condition. */ 1043 spmi_regulator_vs_clear_ocp(vreg); 1044 } else if (vreg->ocp_count <= vreg->ocp_max_retries) { 1045 /* Schedule the over current clear task to run later. */ 1046 schedule_delayed_work(&vreg->ocp_work, 1047 msecs_to_jiffies(vreg->ocp_retry_delay_ms) + 1); 1048 } else { 1049 dev_err(vreg->dev, 1050 "OCP triggered %d times; no further retries\n", 1051 vreg->ocp_count); 1052 } 1053 1054 return IRQ_HANDLED; 1055 } 1056 1057 #define SAW3_VCTL_DATA_MASK 0xFF 1058 #define SAW3_VCTL_CLEAR_MASK 0x700FF 1059 #define SAW3_AVS_CTL_EN_MASK 0x1 1060 #define SAW3_AVS_CTL_TGGL_MASK 0x8000000 1061 #define SAW3_AVS_CTL_CLEAR_MASK 0x7efc00 1062 1063 static struct regmap *saw_regmap; 1064 1065 static void spmi_saw_set_vdd(void *data) 1066 { 1067 u32 vctl, data3, avs_ctl, pmic_sts; 1068 bool avs_enabled = false; 1069 unsigned long timeout; 1070 u8 voltage_sel = *(u8 *)data; 1071 1072 regmap_read(saw_regmap, SAW3_AVS_CTL, &avs_ctl); 1073 regmap_read(saw_regmap, SAW3_VCTL, &vctl); 1074 regmap_read(saw_regmap, SAW3_SPM_PMIC_DATA_3, &data3); 1075 1076 /* select the band */ 1077 vctl &= ~SAW3_VCTL_CLEAR_MASK; 1078 vctl |= (u32)voltage_sel; 1079 1080 data3 &= ~SAW3_VCTL_CLEAR_MASK; 1081 data3 |= (u32)voltage_sel; 1082 1083 /* If AVS is enabled, switch it off during the voltage change */ 1084 avs_enabled = SAW3_AVS_CTL_EN_MASK & avs_ctl; 1085 if (avs_enabled) { 1086 avs_ctl &= ~SAW3_AVS_CTL_TGGL_MASK; 1087 regmap_write(saw_regmap, SAW3_AVS_CTL, avs_ctl); 1088 } 1089 1090 regmap_write(saw_regmap, SAW3_RST, 1); 1091 regmap_write(saw_regmap, SAW3_VCTL, vctl); 1092 regmap_write(saw_regmap, SAW3_SPM_PMIC_DATA_3, data3); 1093 1094 timeout = jiffies + usecs_to_jiffies(100); 1095 do { 1096 regmap_read(saw_regmap, SAW3_PMIC_STS, &pmic_sts); 1097 pmic_sts &= SAW3_VCTL_DATA_MASK; 1098 if (pmic_sts == (u32)voltage_sel) 1099 break; 1100 1101 cpu_relax(); 1102 1103 } while (time_before(jiffies, timeout)); 1104 1105 /* After successful voltage change, switch the AVS back on */ 1106 if (avs_enabled) { 1107 pmic_sts &= 0x3f; 1108 avs_ctl &= ~SAW3_AVS_CTL_CLEAR_MASK; 1109 avs_ctl |= ((pmic_sts - 4) << 10); 1110 avs_ctl |= (pmic_sts << 17); 1111 avs_ctl |= SAW3_AVS_CTL_TGGL_MASK; 1112 regmap_write(saw_regmap, SAW3_AVS_CTL, avs_ctl); 1113 } 1114 } 1115 1116 static int 1117 spmi_regulator_saw_set_voltage(struct regulator_dev *rdev, unsigned selector) 1118 { 1119 struct spmi_regulator *vreg = rdev_get_drvdata(rdev); 1120 int ret; 1121 u8 range_sel, voltage_sel; 1122 1123 ret = spmi_sw_selector_to_hw(vreg, selector, &range_sel, &voltage_sel); 1124 if (ret) 1125 return ret; 1126 1127 if (0 != range_sel) { 1128 dev_dbg(&rdev->dev, "range_sel = %02X voltage_sel = %02X", \ 1129 range_sel, voltage_sel); 1130 return -EINVAL; 1131 } 1132 1133 /* Always do the SAW register writes on the first CPU */ 1134 return smp_call_function_single(0, spmi_saw_set_vdd, \ 1135 &voltage_sel, true); 1136 } 1137 1138 static struct regulator_ops spmi_saw_ops = {}; 1139 1140 static struct regulator_ops spmi_smps_ops = { 1141 .enable = regulator_enable_regmap, 1142 .disable = regulator_disable_regmap, 1143 .is_enabled = regulator_is_enabled_regmap, 1144 .set_voltage_sel = spmi_regulator_common_set_voltage, 1145 .set_voltage_time_sel = spmi_regulator_set_voltage_time_sel, 1146 .get_voltage_sel = spmi_regulator_common_get_voltage, 1147 .map_voltage = spmi_regulator_common_map_voltage, 1148 .list_voltage = spmi_regulator_common_list_voltage, 1149 .set_mode = spmi_regulator_common_set_mode, 1150 .get_mode = spmi_regulator_common_get_mode, 1151 .set_load = spmi_regulator_common_set_load, 1152 .set_pull_down = spmi_regulator_common_set_pull_down, 1153 }; 1154 1155 static struct regulator_ops spmi_ldo_ops = { 1156 .enable = regulator_enable_regmap, 1157 .disable = regulator_disable_regmap, 1158 .is_enabled = regulator_is_enabled_regmap, 1159 .set_voltage_sel = spmi_regulator_common_set_voltage, 1160 .get_voltage_sel = spmi_regulator_common_get_voltage, 1161 .map_voltage = spmi_regulator_common_map_voltage, 1162 .list_voltage = spmi_regulator_common_list_voltage, 1163 .set_mode = spmi_regulator_common_set_mode, 1164 .get_mode = spmi_regulator_common_get_mode, 1165 .set_load = spmi_regulator_common_set_load, 1166 .set_bypass = spmi_regulator_common_set_bypass, 1167 .get_bypass = spmi_regulator_common_get_bypass, 1168 .set_pull_down = spmi_regulator_common_set_pull_down, 1169 .set_soft_start = spmi_regulator_common_set_soft_start, 1170 }; 1171 1172 static struct regulator_ops spmi_ln_ldo_ops = { 1173 .enable = regulator_enable_regmap, 1174 .disable = regulator_disable_regmap, 1175 .is_enabled = regulator_is_enabled_regmap, 1176 .set_voltage_sel = spmi_regulator_common_set_voltage, 1177 .get_voltage_sel = spmi_regulator_common_get_voltage, 1178 .map_voltage = spmi_regulator_common_map_voltage, 1179 .list_voltage = spmi_regulator_common_list_voltage, 1180 .set_bypass = spmi_regulator_common_set_bypass, 1181 .get_bypass = spmi_regulator_common_get_bypass, 1182 }; 1183 1184 static struct regulator_ops spmi_vs_ops = { 1185 .enable = spmi_regulator_vs_enable, 1186 .disable = regulator_disable_regmap, 1187 .is_enabled = regulator_is_enabled_regmap, 1188 .set_pull_down = spmi_regulator_common_set_pull_down, 1189 .set_soft_start = spmi_regulator_common_set_soft_start, 1190 .set_over_current_protection = spmi_regulator_vs_ocp, 1191 .set_mode = spmi_regulator_common_set_mode, 1192 .get_mode = spmi_regulator_common_get_mode, 1193 }; 1194 1195 static struct regulator_ops spmi_boost_ops = { 1196 .enable = regulator_enable_regmap, 1197 .disable = regulator_disable_regmap, 1198 .is_enabled = regulator_is_enabled_regmap, 1199 .set_voltage_sel = spmi_regulator_single_range_set_voltage, 1200 .get_voltage_sel = spmi_regulator_single_range_get_voltage, 1201 .map_voltage = spmi_regulator_single_map_voltage, 1202 .list_voltage = spmi_regulator_common_list_voltage, 1203 .set_input_current_limit = spmi_regulator_set_ilim, 1204 }; 1205 1206 static struct regulator_ops spmi_ftsmps_ops = { 1207 .enable = regulator_enable_regmap, 1208 .disable = regulator_disable_regmap, 1209 .is_enabled = regulator_is_enabled_regmap, 1210 .set_voltage_sel = spmi_regulator_common_set_voltage, 1211 .set_voltage_time_sel = spmi_regulator_set_voltage_time_sel, 1212 .get_voltage_sel = spmi_regulator_common_get_voltage, 1213 .map_voltage = spmi_regulator_common_map_voltage, 1214 .list_voltage = spmi_regulator_common_list_voltage, 1215 .set_mode = spmi_regulator_common_set_mode, 1216 .get_mode = spmi_regulator_common_get_mode, 1217 .set_load = spmi_regulator_common_set_load, 1218 .set_pull_down = spmi_regulator_common_set_pull_down, 1219 }; 1220 1221 static struct regulator_ops spmi_ult_lo_smps_ops = { 1222 .enable = regulator_enable_regmap, 1223 .disable = regulator_disable_regmap, 1224 .is_enabled = regulator_is_enabled_regmap, 1225 .set_voltage_sel = spmi_regulator_ult_lo_smps_set_voltage, 1226 .set_voltage_time_sel = spmi_regulator_set_voltage_time_sel, 1227 .get_voltage_sel = spmi_regulator_ult_lo_smps_get_voltage, 1228 .list_voltage = spmi_regulator_common_list_voltage, 1229 .set_mode = spmi_regulator_common_set_mode, 1230 .get_mode = spmi_regulator_common_get_mode, 1231 .set_load = spmi_regulator_common_set_load, 1232 .set_pull_down = spmi_regulator_common_set_pull_down, 1233 }; 1234 1235 static struct regulator_ops spmi_ult_ho_smps_ops = { 1236 .enable = regulator_enable_regmap, 1237 .disable = regulator_disable_regmap, 1238 .is_enabled = regulator_is_enabled_regmap, 1239 .set_voltage_sel = spmi_regulator_single_range_set_voltage, 1240 .set_voltage_time_sel = spmi_regulator_set_voltage_time_sel, 1241 .get_voltage_sel = spmi_regulator_single_range_get_voltage, 1242 .map_voltage = spmi_regulator_single_map_voltage, 1243 .list_voltage = spmi_regulator_common_list_voltage, 1244 .set_mode = spmi_regulator_common_set_mode, 1245 .get_mode = spmi_regulator_common_get_mode, 1246 .set_load = spmi_regulator_common_set_load, 1247 .set_pull_down = spmi_regulator_common_set_pull_down, 1248 }; 1249 1250 static struct regulator_ops spmi_ult_ldo_ops = { 1251 .enable = regulator_enable_regmap, 1252 .disable = regulator_disable_regmap, 1253 .is_enabled = regulator_is_enabled_regmap, 1254 .set_voltage_sel = spmi_regulator_single_range_set_voltage, 1255 .get_voltage_sel = spmi_regulator_single_range_get_voltage, 1256 .map_voltage = spmi_regulator_single_map_voltage, 1257 .list_voltage = spmi_regulator_common_list_voltage, 1258 .set_mode = spmi_regulator_common_set_mode, 1259 .get_mode = spmi_regulator_common_get_mode, 1260 .set_load = spmi_regulator_common_set_load, 1261 .set_bypass = spmi_regulator_common_set_bypass, 1262 .get_bypass = spmi_regulator_common_get_bypass, 1263 .set_pull_down = spmi_regulator_common_set_pull_down, 1264 .set_soft_start = spmi_regulator_common_set_soft_start, 1265 }; 1266 1267 /* Maximum possible digital major revision value */ 1268 #define INF 0xFF 1269 1270 static const struct spmi_regulator_mapping supported_regulators[] = { 1271 /* type subtype dig_min dig_max ltype ops setpoints hpm_min */ 1272 SPMI_VREG(BUCK, GP_CTL, 0, INF, SMPS, smps, smps, 100000), 1273 SPMI_VREG(LDO, N300, 0, INF, LDO, ldo, nldo1, 10000), 1274 SPMI_VREG(LDO, N600, 0, 0, LDO, ldo, nldo2, 10000), 1275 SPMI_VREG(LDO, N1200, 0, 0, LDO, ldo, nldo2, 10000), 1276 SPMI_VREG(LDO, N600, 1, INF, LDO, ldo, nldo3, 10000), 1277 SPMI_VREG(LDO, N1200, 1, INF, LDO, ldo, nldo3, 10000), 1278 SPMI_VREG(LDO, N600_ST, 0, 0, LDO, ldo, nldo2, 10000), 1279 SPMI_VREG(LDO, N1200_ST, 0, 0, LDO, ldo, nldo2, 10000), 1280 SPMI_VREG(LDO, N600_ST, 1, INF, LDO, ldo, nldo3, 10000), 1281 SPMI_VREG(LDO, N1200_ST, 1, INF, LDO, ldo, nldo3, 10000), 1282 SPMI_VREG(LDO, P50, 0, INF, LDO, ldo, pldo, 5000), 1283 SPMI_VREG(LDO, P150, 0, INF, LDO, ldo, pldo, 10000), 1284 SPMI_VREG(LDO, P300, 0, INF, LDO, ldo, pldo, 10000), 1285 SPMI_VREG(LDO, P600, 0, INF, LDO, ldo, pldo, 10000), 1286 SPMI_VREG(LDO, P1200, 0, INF, LDO, ldo, pldo, 10000), 1287 SPMI_VREG(LDO, LN, 0, INF, LN_LDO, ln_ldo, ln_ldo, 0), 1288 SPMI_VREG(LDO, LV_P50, 0, INF, LDO, ldo, pldo, 5000), 1289 SPMI_VREG(LDO, LV_P150, 0, INF, LDO, ldo, pldo, 10000), 1290 SPMI_VREG(LDO, LV_P300, 0, INF, LDO, ldo, pldo, 10000), 1291 SPMI_VREG(LDO, LV_P600, 0, INF, LDO, ldo, pldo, 10000), 1292 SPMI_VREG(LDO, LV_P1200, 0, INF, LDO, ldo, pldo, 10000), 1293 SPMI_VREG_VS(LV100, 0, INF), 1294 SPMI_VREG_VS(LV300, 0, INF), 1295 SPMI_VREG_VS(MV300, 0, INF), 1296 SPMI_VREG_VS(MV500, 0, INF), 1297 SPMI_VREG_VS(HDMI, 0, INF), 1298 SPMI_VREG_VS(OTG, 0, INF), 1299 SPMI_VREG(BOOST, 5V_BOOST, 0, INF, BOOST, boost, boost, 0), 1300 SPMI_VREG(FTS, FTS_CTL, 0, INF, FTSMPS, ftsmps, ftsmps, 100000), 1301 SPMI_VREG(FTS, FTS2p5_CTL, 0, INF, FTSMPS, ftsmps, ftsmps2p5, 100000), 1302 SPMI_VREG(BOOST_BYP, BB_2A, 0, INF, BOOST_BYP, boost, boost_byp, 0), 1303 SPMI_VREG(ULT_BUCK, ULT_HF_CTL1, 0, INF, ULT_LO_SMPS, ult_lo_smps, 1304 ult_lo_smps, 100000), 1305 SPMI_VREG(ULT_BUCK, ULT_HF_CTL2, 0, INF, ULT_LO_SMPS, ult_lo_smps, 1306 ult_lo_smps, 100000), 1307 SPMI_VREG(ULT_BUCK, ULT_HF_CTL3, 0, INF, ULT_LO_SMPS, ult_lo_smps, 1308 ult_lo_smps, 100000), 1309 SPMI_VREG(ULT_BUCK, ULT_HF_CTL4, 0, INF, ULT_HO_SMPS, ult_ho_smps, 1310 ult_ho_smps, 100000), 1311 SPMI_VREG(ULT_LDO, N300_ST, 0, INF, ULT_LDO, ult_ldo, ult_nldo, 10000), 1312 SPMI_VREG(ULT_LDO, N600_ST, 0, INF, ULT_LDO, ult_ldo, ult_nldo, 10000), 1313 SPMI_VREG(ULT_LDO, N900_ST, 0, INF, ULT_LDO, ult_ldo, ult_nldo, 10000), 1314 SPMI_VREG(ULT_LDO, N1200_ST, 0, INF, ULT_LDO, ult_ldo, ult_nldo, 10000), 1315 SPMI_VREG(ULT_LDO, LV_P150, 0, INF, ULT_LDO, ult_ldo, ult_pldo, 10000), 1316 SPMI_VREG(ULT_LDO, LV_P300, 0, INF, ULT_LDO, ult_ldo, ult_pldo, 10000), 1317 SPMI_VREG(ULT_LDO, LV_P450, 0, INF, ULT_LDO, ult_ldo, ult_pldo, 10000), 1318 SPMI_VREG(ULT_LDO, P600, 0, INF, ULT_LDO, ult_ldo, ult_pldo, 10000), 1319 SPMI_VREG(ULT_LDO, P150, 0, INF, ULT_LDO, ult_ldo, ult_pldo, 10000), 1320 SPMI_VREG(ULT_LDO, P50, 0, INF, ULT_LDO, ult_ldo, ult_pldo, 5000), 1321 }; 1322 1323 static void spmi_calculate_num_voltages(struct spmi_voltage_set_points *points) 1324 { 1325 unsigned int n; 1326 struct spmi_voltage_range *range = points->range; 1327 1328 for (; range < points->range + points->count; range++) { 1329 n = 0; 1330 if (range->set_point_max_uV) { 1331 n = range->set_point_max_uV - range->set_point_min_uV; 1332 n = (n / range->step_uV) + 1; 1333 } 1334 range->n_voltages = n; 1335 points->n_voltages += n; 1336 } 1337 } 1338 1339 static int spmi_regulator_match(struct spmi_regulator *vreg, u16 force_type) 1340 { 1341 const struct spmi_regulator_mapping *mapping; 1342 int ret, i; 1343 u32 dig_major_rev; 1344 u8 version[SPMI_COMMON_REG_SUBTYPE - SPMI_COMMON_REG_DIG_MAJOR_REV + 1]; 1345 u8 type, subtype; 1346 1347 ret = spmi_vreg_read(vreg, SPMI_COMMON_REG_DIG_MAJOR_REV, version, 1348 ARRAY_SIZE(version)); 1349 if (ret) { 1350 dev_dbg(vreg->dev, "could not read version registers\n"); 1351 return ret; 1352 } 1353 dig_major_rev = version[SPMI_COMMON_REG_DIG_MAJOR_REV 1354 - SPMI_COMMON_REG_DIG_MAJOR_REV]; 1355 1356 if (!force_type) { 1357 type = version[SPMI_COMMON_REG_TYPE - 1358 SPMI_COMMON_REG_DIG_MAJOR_REV]; 1359 subtype = version[SPMI_COMMON_REG_SUBTYPE - 1360 SPMI_COMMON_REG_DIG_MAJOR_REV]; 1361 } else { 1362 type = force_type >> 8; 1363 subtype = force_type; 1364 } 1365 1366 for (i = 0; i < ARRAY_SIZE(supported_regulators); i++) { 1367 mapping = &supported_regulators[i]; 1368 if (mapping->type == type && mapping->subtype == subtype 1369 && mapping->revision_min <= dig_major_rev 1370 && mapping->revision_max >= dig_major_rev) 1371 goto found; 1372 } 1373 1374 dev_err(vreg->dev, 1375 "unsupported regulator: name=%s type=0x%02X, subtype=0x%02X, dig major rev=0x%02X\n", 1376 vreg->desc.name, type, subtype, dig_major_rev); 1377 1378 return -ENODEV; 1379 1380 found: 1381 vreg->logical_type = mapping->logical_type; 1382 vreg->set_points = mapping->set_points; 1383 vreg->hpm_min_load = mapping->hpm_min_load; 1384 vreg->desc.ops = mapping->ops; 1385 1386 if (mapping->set_points) { 1387 if (!mapping->set_points->n_voltages) 1388 spmi_calculate_num_voltages(mapping->set_points); 1389 vreg->desc.n_voltages = mapping->set_points->n_voltages; 1390 } 1391 1392 return 0; 1393 } 1394 1395 static int spmi_regulator_init_slew_rate(struct spmi_regulator *vreg) 1396 { 1397 int ret; 1398 u8 reg = 0; 1399 int step, delay, slew_rate, step_delay; 1400 const struct spmi_voltage_range *range; 1401 1402 ret = spmi_vreg_read(vreg, SPMI_COMMON_REG_STEP_CTRL, ®, 1); 1403 if (ret) { 1404 dev_err(vreg->dev, "spmi read failed, ret=%d\n", ret); 1405 return ret; 1406 } 1407 1408 range = spmi_regulator_find_range(vreg); 1409 if (!range) 1410 return -EINVAL; 1411 1412 switch (vreg->logical_type) { 1413 case SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS: 1414 step_delay = SPMI_FTSMPS_STEP_DELAY; 1415 break; 1416 default: 1417 step_delay = SPMI_DEFAULT_STEP_DELAY; 1418 break; 1419 } 1420 1421 step = reg & SPMI_FTSMPS_STEP_CTRL_STEP_MASK; 1422 step >>= SPMI_FTSMPS_STEP_CTRL_STEP_SHIFT; 1423 1424 delay = reg & SPMI_FTSMPS_STEP_CTRL_DELAY_MASK; 1425 delay >>= SPMI_FTSMPS_STEP_CTRL_DELAY_SHIFT; 1426 1427 /* slew_rate has units of uV/us */ 1428 slew_rate = SPMI_FTSMPS_CLOCK_RATE * range->step_uV * (1 << step); 1429 slew_rate /= 1000 * (step_delay << delay); 1430 slew_rate *= SPMI_FTSMPS_STEP_MARGIN_NUM; 1431 slew_rate /= SPMI_FTSMPS_STEP_MARGIN_DEN; 1432 1433 /* Ensure that the slew rate is greater than 0 */ 1434 vreg->slew_rate = max(slew_rate, 1); 1435 1436 return ret; 1437 } 1438 1439 static int spmi_regulator_init_registers(struct spmi_regulator *vreg, 1440 const struct spmi_regulator_init_data *data) 1441 { 1442 int ret; 1443 enum spmi_regulator_logical_type type; 1444 u8 ctrl_reg[8], reg, mask; 1445 1446 type = vreg->logical_type; 1447 1448 ret = spmi_vreg_read(vreg, SPMI_COMMON_REG_VOLTAGE_RANGE, ctrl_reg, 8); 1449 if (ret) 1450 return ret; 1451 1452 /* Set up enable pin control. */ 1453 if ((type == SPMI_REGULATOR_LOGICAL_TYPE_SMPS 1454 || type == SPMI_REGULATOR_LOGICAL_TYPE_LDO 1455 || type == SPMI_REGULATOR_LOGICAL_TYPE_VS) 1456 && !(data->pin_ctrl_enable 1457 & SPMI_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT)) { 1458 ctrl_reg[SPMI_COMMON_IDX_ENABLE] &= 1459 ~SPMI_COMMON_ENABLE_FOLLOW_ALL_MASK; 1460 ctrl_reg[SPMI_COMMON_IDX_ENABLE] |= 1461 data->pin_ctrl_enable & SPMI_COMMON_ENABLE_FOLLOW_ALL_MASK; 1462 } 1463 1464 /* Set up mode pin control. */ 1465 if ((type == SPMI_REGULATOR_LOGICAL_TYPE_SMPS 1466 || type == SPMI_REGULATOR_LOGICAL_TYPE_LDO) 1467 && !(data->pin_ctrl_hpm 1468 & SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT)) { 1469 ctrl_reg[SPMI_COMMON_IDX_MODE] &= 1470 ~SPMI_COMMON_MODE_FOLLOW_ALL_MASK; 1471 ctrl_reg[SPMI_COMMON_IDX_MODE] |= 1472 data->pin_ctrl_hpm & SPMI_COMMON_MODE_FOLLOW_ALL_MASK; 1473 } 1474 1475 if (type == SPMI_REGULATOR_LOGICAL_TYPE_VS 1476 && !(data->pin_ctrl_hpm & SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT)) { 1477 ctrl_reg[SPMI_COMMON_IDX_MODE] &= 1478 ~SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK; 1479 ctrl_reg[SPMI_COMMON_IDX_MODE] |= 1480 data->pin_ctrl_hpm & SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK; 1481 } 1482 1483 if ((type == SPMI_REGULATOR_LOGICAL_TYPE_ULT_LO_SMPS 1484 || type == SPMI_REGULATOR_LOGICAL_TYPE_ULT_HO_SMPS 1485 || type == SPMI_REGULATOR_LOGICAL_TYPE_ULT_LDO) 1486 && !(data->pin_ctrl_hpm 1487 & SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT)) { 1488 ctrl_reg[SPMI_COMMON_IDX_MODE] &= 1489 ~SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK; 1490 ctrl_reg[SPMI_COMMON_IDX_MODE] |= 1491 data->pin_ctrl_hpm & SPMI_COMMON_MODE_FOLLOW_AWAKE_MASK; 1492 } 1493 1494 /* Write back any control register values that were modified. */ 1495 ret = spmi_vreg_write(vreg, SPMI_COMMON_REG_VOLTAGE_RANGE, ctrl_reg, 8); 1496 if (ret) 1497 return ret; 1498 1499 /* Set soft start strength and over current protection for VS. */ 1500 if (type == SPMI_REGULATOR_LOGICAL_TYPE_VS) { 1501 if (data->vs_soft_start_strength 1502 != SPMI_VS_SOFT_START_STR_HW_DEFAULT) { 1503 reg = data->vs_soft_start_strength 1504 & SPMI_VS_SOFT_START_SEL_MASK; 1505 mask = SPMI_VS_SOFT_START_SEL_MASK; 1506 return spmi_vreg_update_bits(vreg, 1507 SPMI_VS_REG_SOFT_START, 1508 reg, mask); 1509 } 1510 } 1511 1512 return 0; 1513 } 1514 1515 static void spmi_regulator_get_dt_config(struct spmi_regulator *vreg, 1516 struct device_node *node, struct spmi_regulator_init_data *data) 1517 { 1518 /* 1519 * Initialize configuration parameters to use hardware default in case 1520 * no value is specified via device tree. 1521 */ 1522 data->pin_ctrl_enable = SPMI_REGULATOR_PIN_CTRL_ENABLE_HW_DEFAULT; 1523 data->pin_ctrl_hpm = SPMI_REGULATOR_PIN_CTRL_HPM_HW_DEFAULT; 1524 data->vs_soft_start_strength = SPMI_VS_SOFT_START_STR_HW_DEFAULT; 1525 1526 /* These bindings are optional, so it is okay if they aren't found. */ 1527 of_property_read_u32(node, "qcom,ocp-max-retries", 1528 &vreg->ocp_max_retries); 1529 of_property_read_u32(node, "qcom,ocp-retry-delay", 1530 &vreg->ocp_retry_delay_ms); 1531 of_property_read_u32(node, "qcom,pin-ctrl-enable", 1532 &data->pin_ctrl_enable); 1533 of_property_read_u32(node, "qcom,pin-ctrl-hpm", &data->pin_ctrl_hpm); 1534 of_property_read_u32(node, "qcom,vs-soft-start-strength", 1535 &data->vs_soft_start_strength); 1536 } 1537 1538 static unsigned int spmi_regulator_of_map_mode(unsigned int mode) 1539 { 1540 if (mode == 1) 1541 return REGULATOR_MODE_NORMAL; 1542 if (mode == 2) 1543 return REGULATOR_MODE_FAST; 1544 1545 return REGULATOR_MODE_IDLE; 1546 } 1547 1548 static int spmi_regulator_of_parse(struct device_node *node, 1549 const struct regulator_desc *desc, 1550 struct regulator_config *config) 1551 { 1552 struct spmi_regulator_init_data data = { }; 1553 struct spmi_regulator *vreg = config->driver_data; 1554 struct device *dev = config->dev; 1555 int ret; 1556 1557 spmi_regulator_get_dt_config(vreg, node, &data); 1558 1559 if (!vreg->ocp_max_retries) 1560 vreg->ocp_max_retries = SPMI_VS_OCP_DEFAULT_MAX_RETRIES; 1561 if (!vreg->ocp_retry_delay_ms) 1562 vreg->ocp_retry_delay_ms = SPMI_VS_OCP_DEFAULT_RETRY_DELAY_MS; 1563 1564 ret = spmi_regulator_init_registers(vreg, &data); 1565 if (ret) { 1566 dev_err(dev, "common initialization failed, ret=%d\n", ret); 1567 return ret; 1568 } 1569 1570 switch (vreg->logical_type) { 1571 case SPMI_REGULATOR_LOGICAL_TYPE_FTSMPS: 1572 case SPMI_REGULATOR_LOGICAL_TYPE_ULT_LO_SMPS: 1573 case SPMI_REGULATOR_LOGICAL_TYPE_ULT_HO_SMPS: 1574 case SPMI_REGULATOR_LOGICAL_TYPE_SMPS: 1575 ret = spmi_regulator_init_slew_rate(vreg); 1576 if (ret) 1577 return ret; 1578 default: 1579 break; 1580 } 1581 1582 if (vreg->logical_type != SPMI_REGULATOR_LOGICAL_TYPE_VS) 1583 vreg->ocp_irq = 0; 1584 1585 if (vreg->ocp_irq) { 1586 ret = devm_request_irq(dev, vreg->ocp_irq, 1587 spmi_regulator_vs_ocp_isr, IRQF_TRIGGER_RISING, "ocp", 1588 vreg); 1589 if (ret < 0) { 1590 dev_err(dev, "failed to request irq %d, ret=%d\n", 1591 vreg->ocp_irq, ret); 1592 return ret; 1593 } 1594 1595 INIT_DELAYED_WORK(&vreg->ocp_work, spmi_regulator_vs_ocp_work); 1596 } 1597 1598 return 0; 1599 } 1600 1601 static const struct spmi_regulator_data pm8941_regulators[] = { 1602 { "s1", 0x1400, "vdd_s1", }, 1603 { "s2", 0x1700, "vdd_s2", }, 1604 { "s3", 0x1a00, "vdd_s3", }, 1605 { "s4", 0xa000, }, 1606 { "l1", 0x4000, "vdd_l1_l3", }, 1607 { "l2", 0x4100, "vdd_l2_lvs_1_2_3", }, 1608 { "l3", 0x4200, "vdd_l1_l3", }, 1609 { "l4", 0x4300, "vdd_l4_l11", }, 1610 { "l5", 0x4400, "vdd_l5_l7", NULL, 0x0410 }, 1611 { "l6", 0x4500, "vdd_l6_l12_l14_l15", }, 1612 { "l7", 0x4600, "vdd_l5_l7", NULL, 0x0410 }, 1613 { "l8", 0x4700, "vdd_l8_l16_l18_19", }, 1614 { "l9", 0x4800, "vdd_l9_l10_l17_l22", }, 1615 { "l10", 0x4900, "vdd_l9_l10_l17_l22", }, 1616 { "l11", 0x4a00, "vdd_l4_l11", }, 1617 { "l12", 0x4b00, "vdd_l6_l12_l14_l15", }, 1618 { "l13", 0x4c00, "vdd_l13_l20_l23_l24", }, 1619 { "l14", 0x4d00, "vdd_l6_l12_l14_l15", }, 1620 { "l15", 0x4e00, "vdd_l6_l12_l14_l15", }, 1621 { "l16", 0x4f00, "vdd_l8_l16_l18_19", }, 1622 { "l17", 0x5000, "vdd_l9_l10_l17_l22", }, 1623 { "l18", 0x5100, "vdd_l8_l16_l18_19", }, 1624 { "l19", 0x5200, "vdd_l8_l16_l18_19", }, 1625 { "l20", 0x5300, "vdd_l13_l20_l23_l24", }, 1626 { "l21", 0x5400, "vdd_l21", }, 1627 { "l22", 0x5500, "vdd_l9_l10_l17_l22", }, 1628 { "l23", 0x5600, "vdd_l13_l20_l23_l24", }, 1629 { "l24", 0x5700, "vdd_l13_l20_l23_l24", }, 1630 { "lvs1", 0x8000, "vdd_l2_lvs_1_2_3", }, 1631 { "lvs2", 0x8100, "vdd_l2_lvs_1_2_3", }, 1632 { "lvs3", 0x8200, "vdd_l2_lvs_1_2_3", }, 1633 { "5vs1", 0x8300, "vin_5vs", "ocp-5vs1", }, 1634 { "5vs2", 0x8400, "vin_5vs", "ocp-5vs2", }, 1635 { } 1636 }; 1637 1638 static const struct spmi_regulator_data pm8841_regulators[] = { 1639 { "s1", 0x1400, "vdd_s1", }, 1640 { "s2", 0x1700, "vdd_s2", NULL, 0x1c08 }, 1641 { "s3", 0x1a00, "vdd_s3", }, 1642 { "s4", 0x1d00, "vdd_s4", NULL, 0x1c08 }, 1643 { "s5", 0x2000, "vdd_s5", NULL, 0x1c08 }, 1644 { "s6", 0x2300, "vdd_s6", NULL, 0x1c08 }, 1645 { "s7", 0x2600, "vdd_s7", NULL, 0x1c08 }, 1646 { "s8", 0x2900, "vdd_s8", NULL, 0x1c08 }, 1647 { } 1648 }; 1649 1650 static const struct spmi_regulator_data pm8916_regulators[] = { 1651 { "s1", 0x1400, "vdd_s1", }, 1652 { "s2", 0x1700, "vdd_s2", }, 1653 { "s3", 0x1a00, "vdd_s3", }, 1654 { "s4", 0x1d00, "vdd_s4", }, 1655 { "l1", 0x4000, "vdd_l1_l3", }, 1656 { "l2", 0x4100, "vdd_l2", }, 1657 { "l3", 0x4200, "vdd_l1_l3", }, 1658 { "l4", 0x4300, "vdd_l4_l5_l6", }, 1659 { "l5", 0x4400, "vdd_l4_l5_l6", }, 1660 { "l6", 0x4500, "vdd_l4_l5_l6", }, 1661 { "l7", 0x4600, "vdd_l7", }, 1662 { "l8", 0x4700, "vdd_l8_l11_l14_l15_l16", }, 1663 { "l9", 0x4800, "vdd_l9_l10_l12_l13_l17_l18", }, 1664 { "l10", 0x4900, "vdd_l9_l10_l12_l13_l17_l18", }, 1665 { "l11", 0x4a00, "vdd_l8_l11_l14_l15_l16", }, 1666 { "l12", 0x4b00, "vdd_l9_l10_l12_l13_l17_l18", }, 1667 { "l13", 0x4c00, "vdd_l9_l10_l12_l13_l17_l18", }, 1668 { "l14", 0x4d00, "vdd_l8_l11_l14_l15_l16", }, 1669 { "l15", 0x4e00, "vdd_l8_l11_l14_l15_l16", }, 1670 { "l16", 0x4f00, "vdd_l8_l11_l14_l15_l16", }, 1671 { "l17", 0x5000, "vdd_l9_l10_l12_l13_l17_l18", }, 1672 { "l18", 0x5100, "vdd_l9_l10_l12_l13_l17_l18", }, 1673 { } 1674 }; 1675 1676 static const struct spmi_regulator_data pm8994_regulators[] = { 1677 { "s1", 0x1400, "vdd_s1", }, 1678 { "s2", 0x1700, "vdd_s2", }, 1679 { "s3", 0x1a00, "vdd_s3", }, 1680 { "s4", 0x1d00, "vdd_s4", }, 1681 { "s5", 0x2000, "vdd_s5", }, 1682 { "s6", 0x2300, "vdd_s6", }, 1683 { "s7", 0x2600, "vdd_s7", }, 1684 { "s8", 0x2900, "vdd_s8", }, 1685 { "s9", 0x2c00, "vdd_s9", }, 1686 { "s10", 0x2f00, "vdd_s10", }, 1687 { "s11", 0x3200, "vdd_s11", }, 1688 { "s12", 0x3500, "vdd_s12", }, 1689 { "l1", 0x4000, "vdd_l1", }, 1690 { "l2", 0x4100, "vdd_l2_l26_l28", }, 1691 { "l3", 0x4200, "vdd_l3_l11", }, 1692 { "l4", 0x4300, "vdd_l4_l27_l31", }, 1693 { "l5", 0x4400, "vdd_l5_l7", }, 1694 { "l6", 0x4500, "vdd_l6_l12_l32", }, 1695 { "l7", 0x4600, "vdd_l5_l7", }, 1696 { "l8", 0x4700, "vdd_l8_l16_l30", }, 1697 { "l9", 0x4800, "vdd_l9_l10_l18_l22", }, 1698 { "l10", 0x4900, "vdd_l9_l10_l18_l22", }, 1699 { "l11", 0x4a00, "vdd_l3_l11", }, 1700 { "l12", 0x4b00, "vdd_l6_l12_l32", }, 1701 { "l13", 0x4c00, "vdd_l13_l19_l23_l24", }, 1702 { "l14", 0x4d00, "vdd_l14_l15", }, 1703 { "l15", 0x4e00, "vdd_l14_l15", }, 1704 { "l16", 0x4f00, "vdd_l8_l16_l30", }, 1705 { "l17", 0x5000, "vdd_l17_l29", }, 1706 { "l18", 0x5100, "vdd_l9_l10_l18_l22", }, 1707 { "l19", 0x5200, "vdd_l13_l19_l23_l24", }, 1708 { "l20", 0x5300, "vdd_l20_l21", }, 1709 { "l21", 0x5400, "vdd_l20_l21", }, 1710 { "l22", 0x5500, "vdd_l9_l10_l18_l22", }, 1711 { "l23", 0x5600, "vdd_l13_l19_l23_l24", }, 1712 { "l24", 0x5700, "vdd_l13_l19_l23_l24", }, 1713 { "l25", 0x5800, "vdd_l25", }, 1714 { "l26", 0x5900, "vdd_l2_l26_l28", }, 1715 { "l27", 0x5a00, "vdd_l4_l27_l31", }, 1716 { "l28", 0x5b00, "vdd_l2_l26_l28", }, 1717 { "l29", 0x5c00, "vdd_l17_l29", }, 1718 { "l30", 0x5d00, "vdd_l8_l16_l30", }, 1719 { "l31", 0x5e00, "vdd_l4_l27_l31", }, 1720 { "l32", 0x5f00, "vdd_l6_l12_l32", }, 1721 { "lvs1", 0x8000, "vdd_lvs_1_2", }, 1722 { "lvs2", 0x8100, "vdd_lvs_1_2", }, 1723 { } 1724 }; 1725 1726 static const struct spmi_regulator_data pmi8994_regulators[] = { 1727 { "s1", 0x1400, "vdd_s1", }, 1728 { "s2", 0x1700, "vdd_s2", }, 1729 { "s3", 0x1a00, "vdd_s3", }, 1730 { "l1", 0x4000, "vdd_l1", }, 1731 { } 1732 }; 1733 1734 static const struct of_device_id qcom_spmi_regulator_match[] = { 1735 { .compatible = "qcom,pm8841-regulators", .data = &pm8841_regulators }, 1736 { .compatible = "qcom,pm8916-regulators", .data = &pm8916_regulators }, 1737 { .compatible = "qcom,pm8941-regulators", .data = &pm8941_regulators }, 1738 { .compatible = "qcom,pm8994-regulators", .data = &pm8994_regulators }, 1739 { .compatible = "qcom,pmi8994-regulators", .data = &pmi8994_regulators }, 1740 { } 1741 }; 1742 MODULE_DEVICE_TABLE(of, qcom_spmi_regulator_match); 1743 1744 static int qcom_spmi_regulator_probe(struct platform_device *pdev) 1745 { 1746 const struct spmi_regulator_data *reg; 1747 const struct of_device_id *match; 1748 struct regulator_config config = { }; 1749 struct regulator_dev *rdev; 1750 struct spmi_regulator *vreg; 1751 struct regmap *regmap; 1752 const char *name; 1753 struct device *dev = &pdev->dev; 1754 struct device_node *node = pdev->dev.of_node; 1755 struct device_node *syscon, *reg_node; 1756 struct property *reg_prop; 1757 int ret, lenp; 1758 struct list_head *vreg_list; 1759 1760 vreg_list = devm_kzalloc(dev, sizeof(*vreg_list), GFP_KERNEL); 1761 if (!vreg_list) 1762 return -ENOMEM; 1763 INIT_LIST_HEAD(vreg_list); 1764 platform_set_drvdata(pdev, vreg_list); 1765 1766 regmap = dev_get_regmap(dev->parent, NULL); 1767 if (!regmap) 1768 return -ENODEV; 1769 1770 match = of_match_device(qcom_spmi_regulator_match, &pdev->dev); 1771 if (!match) 1772 return -ENODEV; 1773 1774 if (of_find_property(node, "qcom,saw-reg", &lenp)) { 1775 syscon = of_parse_phandle(node, "qcom,saw-reg", 0); 1776 saw_regmap = syscon_node_to_regmap(syscon); 1777 of_node_put(syscon); 1778 if (IS_ERR(saw_regmap)) 1779 dev_err(dev, "ERROR reading SAW regmap\n"); 1780 } 1781 1782 for (reg = match->data; reg->name; reg++) { 1783 1784 if (saw_regmap) { 1785 reg_node = of_get_child_by_name(node, reg->name); 1786 reg_prop = of_find_property(reg_node, "qcom,saw-slave", 1787 &lenp); 1788 of_node_put(reg_node); 1789 if (reg_prop) 1790 continue; 1791 } 1792 1793 vreg = devm_kzalloc(dev, sizeof(*vreg), GFP_KERNEL); 1794 if (!vreg) 1795 return -ENOMEM; 1796 1797 vreg->dev = dev; 1798 vreg->base = reg->base; 1799 vreg->regmap = regmap; 1800 if (reg->ocp) { 1801 vreg->ocp_irq = platform_get_irq_byname(pdev, reg->ocp); 1802 if (vreg->ocp_irq < 0) { 1803 ret = vreg->ocp_irq; 1804 goto err; 1805 } 1806 } 1807 vreg->desc.id = -1; 1808 vreg->desc.owner = THIS_MODULE; 1809 vreg->desc.type = REGULATOR_VOLTAGE; 1810 vreg->desc.enable_reg = reg->base + SPMI_COMMON_REG_ENABLE; 1811 vreg->desc.enable_mask = SPMI_COMMON_ENABLE_MASK; 1812 vreg->desc.enable_val = SPMI_COMMON_ENABLE; 1813 vreg->desc.name = name = reg->name; 1814 vreg->desc.supply_name = reg->supply; 1815 vreg->desc.of_match = reg->name; 1816 vreg->desc.of_parse_cb = spmi_regulator_of_parse; 1817 vreg->desc.of_map_mode = spmi_regulator_of_map_mode; 1818 1819 ret = spmi_regulator_match(vreg, reg->force_type); 1820 if (ret) 1821 continue; 1822 1823 if (saw_regmap) { 1824 reg_node = of_get_child_by_name(node, reg->name); 1825 reg_prop = of_find_property(reg_node, "qcom,saw-leader", 1826 &lenp); 1827 of_node_put(reg_node); 1828 if (reg_prop) { 1829 spmi_saw_ops = *(vreg->desc.ops); 1830 spmi_saw_ops.set_voltage_sel = 1831 spmi_regulator_saw_set_voltage; 1832 vreg->desc.ops = &spmi_saw_ops; 1833 } 1834 } 1835 1836 config.dev = dev; 1837 config.driver_data = vreg; 1838 config.regmap = regmap; 1839 rdev = devm_regulator_register(dev, &vreg->desc, &config); 1840 if (IS_ERR(rdev)) { 1841 dev_err(dev, "failed to register %s\n", name); 1842 ret = PTR_ERR(rdev); 1843 goto err; 1844 } 1845 1846 INIT_LIST_HEAD(&vreg->node); 1847 list_add(&vreg->node, vreg_list); 1848 } 1849 1850 return 0; 1851 1852 err: 1853 list_for_each_entry(vreg, vreg_list, node) 1854 if (vreg->ocp_irq) 1855 cancel_delayed_work_sync(&vreg->ocp_work); 1856 return ret; 1857 } 1858 1859 static int qcom_spmi_regulator_remove(struct platform_device *pdev) 1860 { 1861 struct spmi_regulator *vreg; 1862 struct list_head *vreg_list = platform_get_drvdata(pdev); 1863 1864 list_for_each_entry(vreg, vreg_list, node) 1865 if (vreg->ocp_irq) 1866 cancel_delayed_work_sync(&vreg->ocp_work); 1867 1868 return 0; 1869 } 1870 1871 static struct platform_driver qcom_spmi_regulator_driver = { 1872 .driver = { 1873 .name = "qcom-spmi-regulator", 1874 .of_match_table = qcom_spmi_regulator_match, 1875 }, 1876 .probe = qcom_spmi_regulator_probe, 1877 .remove = qcom_spmi_regulator_remove, 1878 }; 1879 module_platform_driver(qcom_spmi_regulator_driver); 1880 1881 MODULE_DESCRIPTION("Qualcomm SPMI PMIC regulator driver"); 1882 MODULE_LICENSE("GPL v2"); 1883 MODULE_ALIAS("platform:qcom-spmi-regulator"); 1884