1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * Copyright 2020 NXP.
4  * NXP PCA9450 pmic driver
5  */
6 
7 #include <linux/err.h>
8 #include <linux/gpio/consumer.h>
9 #include <linux/i2c.h>
10 #include <linux/interrupt.h>
11 #include <linux/kernel.h>
12 #include <linux/module.h>
13 #include <linux/of.h>
14 #include <linux/of_device.h>
15 #include <linux/platform_device.h>
16 #include <linux/regulator/driver.h>
17 #include <linux/regulator/machine.h>
18 #include <linux/regulator/of_regulator.h>
19 #include <linux/regulator/pca9450.h>
20 
21 struct pc9450_dvs_config {
22 	unsigned int run_reg; /* dvs0 */
23 	unsigned int run_mask;
24 	unsigned int standby_reg; /* dvs1 */
25 	unsigned int standby_mask;
26 };
27 
28 struct pca9450_regulator_desc {
29 	struct regulator_desc desc;
30 	const struct pc9450_dvs_config dvs;
31 };
32 
33 struct pca9450 {
34 	struct device *dev;
35 	struct regmap *regmap;
36 	struct gpio_desc *sd_vsel_gpio;
37 	enum pca9450_chip_type type;
38 	unsigned int rcnt;
39 	int irq;
40 };
41 
42 static const struct regmap_range pca9450_status_range = {
43 	.range_min = PCA9450_REG_INT1,
44 	.range_max = PCA9450_REG_PWRON_STAT,
45 };
46 
47 static const struct regmap_access_table pca9450_volatile_regs = {
48 	.yes_ranges = &pca9450_status_range,
49 	.n_yes_ranges = 1,
50 };
51 
52 static const struct regmap_config pca9450_regmap_config = {
53 	.reg_bits = 8,
54 	.val_bits = 8,
55 	.volatile_table = &pca9450_volatile_regs,
56 	.max_register = PCA9450_MAX_REGISTER - 1,
57 	.cache_type = REGCACHE_RBTREE,
58 };
59 
60 /*
61  * BUCK1/2/3
62  * BUCK1RAM[1:0] BUCK1 DVS ramp rate setting
63  * 00: 25mV/1usec
64  * 01: 25mV/2usec
65  * 10: 25mV/4usec
66  * 11: 25mV/8usec
67  */
68 static const unsigned int pca9450_dvs_buck_ramp_table[] = {
69 	25000, 12500, 6250, 3125
70 };
71 
72 static const struct regulator_ops pca9450_dvs_buck_regulator_ops = {
73 	.enable = regulator_enable_regmap,
74 	.disable = regulator_disable_regmap,
75 	.is_enabled = regulator_is_enabled_regmap,
76 	.list_voltage = regulator_list_voltage_linear_range,
77 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
78 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
79 	.set_voltage_time_sel = regulator_set_voltage_time_sel,
80 	.set_ramp_delay	= regulator_set_ramp_delay_regmap,
81 };
82 
83 static const struct regulator_ops pca9450_buck_regulator_ops = {
84 	.enable = regulator_enable_regmap,
85 	.disable = regulator_disable_regmap,
86 	.is_enabled = regulator_is_enabled_regmap,
87 	.list_voltage = regulator_list_voltage_linear_range,
88 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
89 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
90 	.set_voltage_time_sel = regulator_set_voltage_time_sel,
91 };
92 
93 static const struct regulator_ops pca9450_ldo_regulator_ops = {
94 	.enable = regulator_enable_regmap,
95 	.disable = regulator_disable_regmap,
96 	.is_enabled = regulator_is_enabled_regmap,
97 	.list_voltage = regulator_list_voltage_linear_range,
98 	.set_voltage_sel = regulator_set_voltage_sel_regmap,
99 	.get_voltage_sel = regulator_get_voltage_sel_regmap,
100 };
101 
102 /*
103  * BUCK1/2/3
104  * 0.60 to 2.1875V (12.5mV step)
105  */
106 static const struct linear_range pca9450_dvs_buck_volts[] = {
107 	REGULATOR_LINEAR_RANGE(600000,  0x00, 0x7F, 12500),
108 };
109 
110 /*
111  * BUCK4/5/6
112  * 0.6V to 3.4V (25mV step)
113  */
114 static const struct linear_range pca9450_buck_volts[] = {
115 	REGULATOR_LINEAR_RANGE(600000, 0x00, 0x70, 25000),
116 	REGULATOR_LINEAR_RANGE(3400000, 0x71, 0x7F, 0),
117 };
118 
119 /*
120  * LDO1
121  * 1.6 to 3.3V ()
122  */
123 static const struct linear_range pca9450_ldo1_volts[] = {
124 	REGULATOR_LINEAR_RANGE(1600000, 0x00, 0x03, 100000),
125 	REGULATOR_LINEAR_RANGE(3000000, 0x04, 0x07, 100000),
126 };
127 
128 /*
129  * LDO2
130  * 0.8 to 1.15V (50mV step)
131  */
132 static const struct linear_range pca9450_ldo2_volts[] = {
133 	REGULATOR_LINEAR_RANGE(800000, 0x00, 0x07, 50000),
134 };
135 
136 /*
137  * LDO3/4
138  * 0.8 to 3.3V (100mV step)
139  */
140 static const struct linear_range pca9450_ldo34_volts[] = {
141 	REGULATOR_LINEAR_RANGE(800000, 0x00, 0x19, 100000),
142 	REGULATOR_LINEAR_RANGE(3300000, 0x1A, 0x1F, 0),
143 };
144 
145 /*
146  * LDO5
147  * 1.8 to 3.3V (100mV step)
148  */
149 static const struct linear_range pca9450_ldo5_volts[] = {
150 	REGULATOR_LINEAR_RANGE(1800000,  0x00, 0x0F, 100000),
151 };
152 
153 static int buck_set_dvs(const struct regulator_desc *desc,
154 			struct device_node *np, struct regmap *regmap,
155 			char *prop, unsigned int reg, unsigned int mask)
156 {
157 	int ret, i;
158 	uint32_t uv;
159 
160 	ret = of_property_read_u32(np, prop, &uv);
161 	if (ret == -EINVAL)
162 		return 0;
163 	else if (ret)
164 		return ret;
165 
166 	for (i = 0; i < desc->n_voltages; i++) {
167 		ret = regulator_desc_list_voltage_linear_range(desc, i);
168 		if (ret < 0)
169 			continue;
170 		if (ret == uv) {
171 			i <<= ffs(desc->vsel_mask) - 1;
172 			ret = regmap_update_bits(regmap, reg, mask, i);
173 			break;
174 		}
175 	}
176 
177 	if (ret == 0) {
178 		struct pca9450_regulator_desc *regulator = container_of(desc,
179 					struct pca9450_regulator_desc, desc);
180 
181 		/* Enable DVS control through PMIC_STBY_REQ for this BUCK */
182 		ret = regmap_update_bits(regmap, regulator->desc.enable_reg,
183 					 BUCK1_DVS_CTRL, BUCK1_DVS_CTRL);
184 	}
185 	return ret;
186 }
187 
188 static int pca9450_set_dvs_levels(struct device_node *np,
189 			    const struct regulator_desc *desc,
190 			    struct regulator_config *cfg)
191 {
192 	struct pca9450_regulator_desc *data = container_of(desc,
193 					struct pca9450_regulator_desc, desc);
194 	const struct pc9450_dvs_config *dvs = &data->dvs;
195 	unsigned int reg, mask;
196 	char *prop;
197 	int i, ret = 0;
198 
199 	for (i = 0; i < PCA9450_DVS_LEVEL_MAX; i++) {
200 		switch (i) {
201 		case PCA9450_DVS_LEVEL_RUN:
202 			prop = "nxp,dvs-run-voltage";
203 			reg = dvs->run_reg;
204 			mask = dvs->run_mask;
205 			break;
206 		case PCA9450_DVS_LEVEL_STANDBY:
207 			prop = "nxp,dvs-standby-voltage";
208 			reg = dvs->standby_reg;
209 			mask = dvs->standby_mask;
210 			break;
211 		default:
212 			return -EINVAL;
213 		}
214 
215 		ret = buck_set_dvs(desc, np, cfg->regmap, prop, reg, mask);
216 		if (ret)
217 			break;
218 	}
219 
220 	return ret;
221 }
222 
223 static const struct pca9450_regulator_desc pca9450a_regulators[] = {
224 	{
225 		.desc = {
226 			.name = "buck1",
227 			.of_match = of_match_ptr("BUCK1"),
228 			.regulators_node = of_match_ptr("regulators"),
229 			.id = PCA9450_BUCK1,
230 			.ops = &pca9450_dvs_buck_regulator_ops,
231 			.type = REGULATOR_VOLTAGE,
232 			.n_voltages = PCA9450_BUCK1_VOLTAGE_NUM,
233 			.linear_ranges = pca9450_dvs_buck_volts,
234 			.n_linear_ranges = ARRAY_SIZE(pca9450_dvs_buck_volts),
235 			.vsel_reg = PCA9450_REG_BUCK1OUT_DVS0,
236 			.vsel_mask = BUCK1OUT_DVS0_MASK,
237 			.enable_reg = PCA9450_REG_BUCK1CTRL,
238 			.enable_mask = BUCK1_ENMODE_MASK,
239 			.ramp_reg = PCA9450_REG_BUCK1CTRL,
240 			.ramp_mask = BUCK1_RAMP_MASK,
241 			.ramp_delay_table = pca9450_dvs_buck_ramp_table,
242 			.n_ramp_values = ARRAY_SIZE(pca9450_dvs_buck_ramp_table),
243 			.owner = THIS_MODULE,
244 			.of_parse_cb = pca9450_set_dvs_levels,
245 		},
246 		.dvs = {
247 			.run_reg = PCA9450_REG_BUCK1OUT_DVS0,
248 			.run_mask = BUCK1OUT_DVS0_MASK,
249 			.standby_reg = PCA9450_REG_BUCK1OUT_DVS1,
250 			.standby_mask = BUCK1OUT_DVS1_MASK,
251 		},
252 	},
253 	{
254 		.desc = {
255 			.name = "buck2",
256 			.of_match = of_match_ptr("BUCK2"),
257 			.regulators_node = of_match_ptr("regulators"),
258 			.id = PCA9450_BUCK2,
259 			.ops = &pca9450_dvs_buck_regulator_ops,
260 			.type = REGULATOR_VOLTAGE,
261 			.n_voltages = PCA9450_BUCK2_VOLTAGE_NUM,
262 			.linear_ranges = pca9450_dvs_buck_volts,
263 			.n_linear_ranges = ARRAY_SIZE(pca9450_dvs_buck_volts),
264 			.vsel_reg = PCA9450_REG_BUCK2OUT_DVS0,
265 			.vsel_mask = BUCK2OUT_DVS0_MASK,
266 			.enable_reg = PCA9450_REG_BUCK2CTRL,
267 			.enable_mask = BUCK1_ENMODE_MASK,
268 			.ramp_reg = PCA9450_REG_BUCK2CTRL,
269 			.ramp_mask = BUCK2_RAMP_MASK,
270 			.ramp_delay_table = pca9450_dvs_buck_ramp_table,
271 			.n_ramp_values = ARRAY_SIZE(pca9450_dvs_buck_ramp_table),
272 			.owner = THIS_MODULE,
273 			.of_parse_cb = pca9450_set_dvs_levels,
274 		},
275 		.dvs = {
276 			.run_reg = PCA9450_REG_BUCK2OUT_DVS0,
277 			.run_mask = BUCK2OUT_DVS0_MASK,
278 			.standby_reg = PCA9450_REG_BUCK2OUT_DVS1,
279 			.standby_mask = BUCK2OUT_DVS1_MASK,
280 		},
281 	},
282 	{
283 		.desc = {
284 			.name = "buck3",
285 			.of_match = of_match_ptr("BUCK3"),
286 			.regulators_node = of_match_ptr("regulators"),
287 			.id = PCA9450_BUCK3,
288 			.ops = &pca9450_dvs_buck_regulator_ops,
289 			.type = REGULATOR_VOLTAGE,
290 			.n_voltages = PCA9450_BUCK3_VOLTAGE_NUM,
291 			.linear_ranges = pca9450_dvs_buck_volts,
292 			.n_linear_ranges = ARRAY_SIZE(pca9450_dvs_buck_volts),
293 			.vsel_reg = PCA9450_REG_BUCK3OUT_DVS0,
294 			.vsel_mask = BUCK3OUT_DVS0_MASK,
295 			.enable_reg = PCA9450_REG_BUCK3CTRL,
296 			.enable_mask = BUCK3_ENMODE_MASK,
297 			.ramp_reg = PCA9450_REG_BUCK3CTRL,
298 			.ramp_mask = BUCK3_RAMP_MASK,
299 			.ramp_delay_table = pca9450_dvs_buck_ramp_table,
300 			.n_ramp_values = ARRAY_SIZE(pca9450_dvs_buck_ramp_table),
301 			.owner = THIS_MODULE,
302 			.of_parse_cb = pca9450_set_dvs_levels,
303 		},
304 		.dvs = {
305 			.run_reg = PCA9450_REG_BUCK3OUT_DVS0,
306 			.run_mask = BUCK3OUT_DVS0_MASK,
307 			.standby_reg = PCA9450_REG_BUCK3OUT_DVS1,
308 			.standby_mask = BUCK3OUT_DVS1_MASK,
309 		},
310 	},
311 	{
312 		.desc = {
313 			.name = "buck4",
314 			.of_match = of_match_ptr("BUCK4"),
315 			.regulators_node = of_match_ptr("regulators"),
316 			.id = PCA9450_BUCK4,
317 			.ops = &pca9450_buck_regulator_ops,
318 			.type = REGULATOR_VOLTAGE,
319 			.n_voltages = PCA9450_BUCK4_VOLTAGE_NUM,
320 			.linear_ranges = pca9450_buck_volts,
321 			.n_linear_ranges = ARRAY_SIZE(pca9450_buck_volts),
322 			.vsel_reg = PCA9450_REG_BUCK4OUT,
323 			.vsel_mask = BUCK4OUT_MASK,
324 			.enable_reg = PCA9450_REG_BUCK4CTRL,
325 			.enable_mask = BUCK4_ENMODE_MASK,
326 			.owner = THIS_MODULE,
327 		},
328 	},
329 	{
330 		.desc = {
331 			.name = "buck5",
332 			.of_match = of_match_ptr("BUCK5"),
333 			.regulators_node = of_match_ptr("regulators"),
334 			.id = PCA9450_BUCK5,
335 			.ops = &pca9450_buck_regulator_ops,
336 			.type = REGULATOR_VOLTAGE,
337 			.n_voltages = PCA9450_BUCK5_VOLTAGE_NUM,
338 			.linear_ranges = pca9450_buck_volts,
339 			.n_linear_ranges = ARRAY_SIZE(pca9450_buck_volts),
340 			.vsel_reg = PCA9450_REG_BUCK5OUT,
341 			.vsel_mask = BUCK5OUT_MASK,
342 			.enable_reg = PCA9450_REG_BUCK5CTRL,
343 			.enable_mask = BUCK5_ENMODE_MASK,
344 			.owner = THIS_MODULE,
345 		},
346 	},
347 	{
348 		.desc = {
349 			.name = "buck6",
350 			.of_match = of_match_ptr("BUCK6"),
351 			.regulators_node = of_match_ptr("regulators"),
352 			.id = PCA9450_BUCK6,
353 			.ops = &pca9450_buck_regulator_ops,
354 			.type = REGULATOR_VOLTAGE,
355 			.n_voltages = PCA9450_BUCK6_VOLTAGE_NUM,
356 			.linear_ranges = pca9450_buck_volts,
357 			.n_linear_ranges = ARRAY_SIZE(pca9450_buck_volts),
358 			.vsel_reg = PCA9450_REG_BUCK6OUT,
359 			.vsel_mask = BUCK6OUT_MASK,
360 			.enable_reg = PCA9450_REG_BUCK6CTRL,
361 			.enable_mask = BUCK6_ENMODE_MASK,
362 			.owner = THIS_MODULE,
363 		},
364 	},
365 	{
366 		.desc = {
367 			.name = "ldo1",
368 			.of_match = of_match_ptr("LDO1"),
369 			.regulators_node = of_match_ptr("regulators"),
370 			.id = PCA9450_LDO1,
371 			.ops = &pca9450_ldo_regulator_ops,
372 			.type = REGULATOR_VOLTAGE,
373 			.n_voltages = PCA9450_LDO1_VOLTAGE_NUM,
374 			.linear_ranges = pca9450_ldo1_volts,
375 			.n_linear_ranges = ARRAY_SIZE(pca9450_ldo1_volts),
376 			.vsel_reg = PCA9450_REG_LDO1CTRL,
377 			.vsel_mask = LDO1OUT_MASK,
378 			.enable_reg = PCA9450_REG_LDO1CTRL,
379 			.enable_mask = LDO1_EN_MASK,
380 			.owner = THIS_MODULE,
381 		},
382 	},
383 	{
384 		.desc = {
385 			.name = "ldo2",
386 			.of_match = of_match_ptr("LDO2"),
387 			.regulators_node = of_match_ptr("regulators"),
388 			.id = PCA9450_LDO2,
389 			.ops = &pca9450_ldo_regulator_ops,
390 			.type = REGULATOR_VOLTAGE,
391 			.n_voltages = PCA9450_LDO2_VOLTAGE_NUM,
392 			.linear_ranges = pca9450_ldo2_volts,
393 			.n_linear_ranges = ARRAY_SIZE(pca9450_ldo2_volts),
394 			.vsel_reg = PCA9450_REG_LDO2CTRL,
395 			.vsel_mask = LDO2OUT_MASK,
396 			.enable_reg = PCA9450_REG_LDO2CTRL,
397 			.enable_mask = LDO2_EN_MASK,
398 			.owner = THIS_MODULE,
399 		},
400 	},
401 	{
402 		.desc = {
403 			.name = "ldo3",
404 			.of_match = of_match_ptr("LDO3"),
405 			.regulators_node = of_match_ptr("regulators"),
406 			.id = PCA9450_LDO3,
407 			.ops = &pca9450_ldo_regulator_ops,
408 			.type = REGULATOR_VOLTAGE,
409 			.n_voltages = PCA9450_LDO3_VOLTAGE_NUM,
410 			.linear_ranges = pca9450_ldo34_volts,
411 			.n_linear_ranges = ARRAY_SIZE(pca9450_ldo34_volts),
412 			.vsel_reg = PCA9450_REG_LDO3CTRL,
413 			.vsel_mask = LDO3OUT_MASK,
414 			.enable_reg = PCA9450_REG_LDO3CTRL,
415 			.enable_mask = LDO3_EN_MASK,
416 			.owner = THIS_MODULE,
417 		},
418 	},
419 	{
420 		.desc = {
421 			.name = "ldo4",
422 			.of_match = of_match_ptr("LDO4"),
423 			.regulators_node = of_match_ptr("regulators"),
424 			.id = PCA9450_LDO4,
425 			.ops = &pca9450_ldo_regulator_ops,
426 			.type = REGULATOR_VOLTAGE,
427 			.n_voltages = PCA9450_LDO4_VOLTAGE_NUM,
428 			.linear_ranges = pca9450_ldo34_volts,
429 			.n_linear_ranges = ARRAY_SIZE(pca9450_ldo34_volts),
430 			.vsel_reg = PCA9450_REG_LDO4CTRL,
431 			.vsel_mask = LDO4OUT_MASK,
432 			.enable_reg = PCA9450_REG_LDO4CTRL,
433 			.enable_mask = LDO4_EN_MASK,
434 			.owner = THIS_MODULE,
435 		},
436 	},
437 	{
438 		.desc = {
439 			.name = "ldo5",
440 			.of_match = of_match_ptr("LDO5"),
441 			.regulators_node = of_match_ptr("regulators"),
442 			.id = PCA9450_LDO5,
443 			.ops = &pca9450_ldo_regulator_ops,
444 			.type = REGULATOR_VOLTAGE,
445 			.n_voltages = PCA9450_LDO5_VOLTAGE_NUM,
446 			.linear_ranges = pca9450_ldo5_volts,
447 			.n_linear_ranges = ARRAY_SIZE(pca9450_ldo5_volts),
448 			.vsel_reg = PCA9450_REG_LDO5CTRL_H,
449 			.vsel_mask = LDO5HOUT_MASK,
450 			.enable_reg = PCA9450_REG_LDO5CTRL_H,
451 			.enable_mask = LDO5H_EN_MASK,
452 			.owner = THIS_MODULE,
453 		},
454 	},
455 };
456 
457 /*
458  * Buck3 removed on PCA9450B and connected with Buck1 internal for dual phase
459  * on PCA9450C as no Buck3.
460  */
461 static const struct pca9450_regulator_desc pca9450bc_regulators[] = {
462 	{
463 		.desc = {
464 			.name = "buck1",
465 			.of_match = of_match_ptr("BUCK1"),
466 			.regulators_node = of_match_ptr("regulators"),
467 			.id = PCA9450_BUCK1,
468 			.ops = &pca9450_dvs_buck_regulator_ops,
469 			.type = REGULATOR_VOLTAGE,
470 			.n_voltages = PCA9450_BUCK1_VOLTAGE_NUM,
471 			.linear_ranges = pca9450_dvs_buck_volts,
472 			.n_linear_ranges = ARRAY_SIZE(pca9450_dvs_buck_volts),
473 			.vsel_reg = PCA9450_REG_BUCK1OUT_DVS0,
474 			.vsel_mask = BUCK1OUT_DVS0_MASK,
475 			.enable_reg = PCA9450_REG_BUCK1CTRL,
476 			.enable_mask = BUCK1_ENMODE_MASK,
477 			.ramp_reg = PCA9450_REG_BUCK1CTRL,
478 			.ramp_mask = BUCK1_RAMP_MASK,
479 			.ramp_delay_table = pca9450_dvs_buck_ramp_table,
480 			.n_ramp_values = ARRAY_SIZE(pca9450_dvs_buck_ramp_table),
481 			.owner = THIS_MODULE,
482 			.of_parse_cb = pca9450_set_dvs_levels,
483 		},
484 		.dvs = {
485 			.run_reg = PCA9450_REG_BUCK1OUT_DVS0,
486 			.run_mask = BUCK1OUT_DVS0_MASK,
487 			.standby_reg = PCA9450_REG_BUCK1OUT_DVS1,
488 			.standby_mask = BUCK1OUT_DVS1_MASK,
489 		},
490 	},
491 	{
492 		.desc = {
493 			.name = "buck2",
494 			.of_match = of_match_ptr("BUCK2"),
495 			.regulators_node = of_match_ptr("regulators"),
496 			.id = PCA9450_BUCK2,
497 			.ops = &pca9450_dvs_buck_regulator_ops,
498 			.type = REGULATOR_VOLTAGE,
499 			.n_voltages = PCA9450_BUCK2_VOLTAGE_NUM,
500 			.linear_ranges = pca9450_dvs_buck_volts,
501 			.n_linear_ranges = ARRAY_SIZE(pca9450_dvs_buck_volts),
502 			.vsel_reg = PCA9450_REG_BUCK2OUT_DVS0,
503 			.vsel_mask = BUCK2OUT_DVS0_MASK,
504 			.enable_reg = PCA9450_REG_BUCK2CTRL,
505 			.enable_mask = BUCK1_ENMODE_MASK,
506 			.ramp_reg = PCA9450_REG_BUCK2CTRL,
507 			.ramp_mask = BUCK2_RAMP_MASK,
508 			.ramp_delay_table = pca9450_dvs_buck_ramp_table,
509 			.n_ramp_values = ARRAY_SIZE(pca9450_dvs_buck_ramp_table),
510 			.owner = THIS_MODULE,
511 			.of_parse_cb = pca9450_set_dvs_levels,
512 		},
513 		.dvs = {
514 			.run_reg = PCA9450_REG_BUCK2OUT_DVS0,
515 			.run_mask = BUCK2OUT_DVS0_MASK,
516 			.standby_reg = PCA9450_REG_BUCK2OUT_DVS1,
517 			.standby_mask = BUCK2OUT_DVS1_MASK,
518 		},
519 	},
520 	{
521 		.desc = {
522 			.name = "buck4",
523 			.of_match = of_match_ptr("BUCK4"),
524 			.regulators_node = of_match_ptr("regulators"),
525 			.id = PCA9450_BUCK4,
526 			.ops = &pca9450_buck_regulator_ops,
527 			.type = REGULATOR_VOLTAGE,
528 			.n_voltages = PCA9450_BUCK4_VOLTAGE_NUM,
529 			.linear_ranges = pca9450_buck_volts,
530 			.n_linear_ranges = ARRAY_SIZE(pca9450_buck_volts),
531 			.vsel_reg = PCA9450_REG_BUCK4OUT,
532 			.vsel_mask = BUCK4OUT_MASK,
533 			.enable_reg = PCA9450_REG_BUCK4CTRL,
534 			.enable_mask = BUCK4_ENMODE_MASK,
535 			.owner = THIS_MODULE,
536 		},
537 	},
538 	{
539 		.desc = {
540 			.name = "buck5",
541 			.of_match = of_match_ptr("BUCK5"),
542 			.regulators_node = of_match_ptr("regulators"),
543 			.id = PCA9450_BUCK5,
544 			.ops = &pca9450_buck_regulator_ops,
545 			.type = REGULATOR_VOLTAGE,
546 			.n_voltages = PCA9450_BUCK5_VOLTAGE_NUM,
547 			.linear_ranges = pca9450_buck_volts,
548 			.n_linear_ranges = ARRAY_SIZE(pca9450_buck_volts),
549 			.vsel_reg = PCA9450_REG_BUCK5OUT,
550 			.vsel_mask = BUCK5OUT_MASK,
551 			.enable_reg = PCA9450_REG_BUCK5CTRL,
552 			.enable_mask = BUCK5_ENMODE_MASK,
553 			.owner = THIS_MODULE,
554 		},
555 	},
556 	{
557 		.desc = {
558 			.name = "buck6",
559 			.of_match = of_match_ptr("BUCK6"),
560 			.regulators_node = of_match_ptr("regulators"),
561 			.id = PCA9450_BUCK6,
562 			.ops = &pca9450_buck_regulator_ops,
563 			.type = REGULATOR_VOLTAGE,
564 			.n_voltages = PCA9450_BUCK6_VOLTAGE_NUM,
565 			.linear_ranges = pca9450_buck_volts,
566 			.n_linear_ranges = ARRAY_SIZE(pca9450_buck_volts),
567 			.vsel_reg = PCA9450_REG_BUCK6OUT,
568 			.vsel_mask = BUCK6OUT_MASK,
569 			.enable_reg = PCA9450_REG_BUCK6CTRL,
570 			.enable_mask = BUCK6_ENMODE_MASK,
571 			.owner = THIS_MODULE,
572 		},
573 	},
574 	{
575 		.desc = {
576 			.name = "ldo1",
577 			.of_match = of_match_ptr("LDO1"),
578 			.regulators_node = of_match_ptr("regulators"),
579 			.id = PCA9450_LDO1,
580 			.ops = &pca9450_ldo_regulator_ops,
581 			.type = REGULATOR_VOLTAGE,
582 			.n_voltages = PCA9450_LDO1_VOLTAGE_NUM,
583 			.linear_ranges = pca9450_ldo1_volts,
584 			.n_linear_ranges = ARRAY_SIZE(pca9450_ldo1_volts),
585 			.vsel_reg = PCA9450_REG_LDO1CTRL,
586 			.vsel_mask = LDO1OUT_MASK,
587 			.enable_reg = PCA9450_REG_LDO1CTRL,
588 			.enable_mask = LDO1_EN_MASK,
589 			.owner = THIS_MODULE,
590 		},
591 	},
592 	{
593 		.desc = {
594 			.name = "ldo2",
595 			.of_match = of_match_ptr("LDO2"),
596 			.regulators_node = of_match_ptr("regulators"),
597 			.id = PCA9450_LDO2,
598 			.ops = &pca9450_ldo_regulator_ops,
599 			.type = REGULATOR_VOLTAGE,
600 			.n_voltages = PCA9450_LDO2_VOLTAGE_NUM,
601 			.linear_ranges = pca9450_ldo2_volts,
602 			.n_linear_ranges = ARRAY_SIZE(pca9450_ldo2_volts),
603 			.vsel_reg = PCA9450_REG_LDO2CTRL,
604 			.vsel_mask = LDO2OUT_MASK,
605 			.enable_reg = PCA9450_REG_LDO2CTRL,
606 			.enable_mask = LDO2_EN_MASK,
607 			.owner = THIS_MODULE,
608 		},
609 	},
610 	{
611 		.desc = {
612 			.name = "ldo3",
613 			.of_match = of_match_ptr("LDO3"),
614 			.regulators_node = of_match_ptr("regulators"),
615 			.id = PCA9450_LDO3,
616 			.ops = &pca9450_ldo_regulator_ops,
617 			.type = REGULATOR_VOLTAGE,
618 			.n_voltages = PCA9450_LDO3_VOLTAGE_NUM,
619 			.linear_ranges = pca9450_ldo34_volts,
620 			.n_linear_ranges = ARRAY_SIZE(pca9450_ldo34_volts),
621 			.vsel_reg = PCA9450_REG_LDO3CTRL,
622 			.vsel_mask = LDO3OUT_MASK,
623 			.enable_reg = PCA9450_REG_LDO3CTRL,
624 			.enable_mask = LDO3_EN_MASK,
625 			.owner = THIS_MODULE,
626 		},
627 	},
628 	{
629 		.desc = {
630 			.name = "ldo4",
631 			.of_match = of_match_ptr("LDO4"),
632 			.regulators_node = of_match_ptr("regulators"),
633 			.id = PCA9450_LDO4,
634 			.ops = &pca9450_ldo_regulator_ops,
635 			.type = REGULATOR_VOLTAGE,
636 			.n_voltages = PCA9450_LDO4_VOLTAGE_NUM,
637 			.linear_ranges = pca9450_ldo34_volts,
638 			.n_linear_ranges = ARRAY_SIZE(pca9450_ldo34_volts),
639 			.vsel_reg = PCA9450_REG_LDO4CTRL,
640 			.vsel_mask = LDO4OUT_MASK,
641 			.enable_reg = PCA9450_REG_LDO4CTRL,
642 			.enable_mask = LDO4_EN_MASK,
643 			.owner = THIS_MODULE,
644 		},
645 	},
646 	{
647 		.desc = {
648 			.name = "ldo5",
649 			.of_match = of_match_ptr("LDO5"),
650 			.regulators_node = of_match_ptr("regulators"),
651 			.id = PCA9450_LDO5,
652 			.ops = &pca9450_ldo_regulator_ops,
653 			.type = REGULATOR_VOLTAGE,
654 			.n_voltages = PCA9450_LDO5_VOLTAGE_NUM,
655 			.linear_ranges = pca9450_ldo5_volts,
656 			.n_linear_ranges = ARRAY_SIZE(pca9450_ldo5_volts),
657 			.vsel_reg = PCA9450_REG_LDO5CTRL_H,
658 			.vsel_mask = LDO5HOUT_MASK,
659 			.enable_reg = PCA9450_REG_LDO5CTRL_H,
660 			.enable_mask = LDO5H_EN_MASK,
661 			.owner = THIS_MODULE,
662 		},
663 	},
664 };
665 
666 static irqreturn_t pca9450_irq_handler(int irq, void *data)
667 {
668 	struct pca9450 *pca9450 = data;
669 	struct regmap *regmap = pca9450->regmap;
670 	unsigned int status;
671 	int ret;
672 
673 	ret = regmap_read(regmap, PCA9450_REG_INT1, &status);
674 	if (ret < 0) {
675 		dev_err(pca9450->dev,
676 			"Failed to read INT1(%d)\n", ret);
677 		return IRQ_NONE;
678 	}
679 
680 	if (status & IRQ_PWRON)
681 		dev_warn(pca9450->dev, "PWRON interrupt.\n");
682 
683 	if (status & IRQ_WDOGB)
684 		dev_warn(pca9450->dev, "WDOGB interrupt.\n");
685 
686 	if (status & IRQ_VR_FLT1)
687 		dev_warn(pca9450->dev, "VRFLT1 interrupt.\n");
688 
689 	if (status & IRQ_VR_FLT2)
690 		dev_warn(pca9450->dev, "VRFLT2 interrupt.\n");
691 
692 	if (status & IRQ_LOWVSYS)
693 		dev_warn(pca9450->dev, "LOWVSYS interrupt.\n");
694 
695 	if (status & IRQ_THERM_105)
696 		dev_warn(pca9450->dev, "IRQ_THERM_105 interrupt.\n");
697 
698 	if (status & IRQ_THERM_125)
699 		dev_warn(pca9450->dev, "IRQ_THERM_125 interrupt.\n");
700 
701 	return IRQ_HANDLED;
702 }
703 
704 static int pca9450_i2c_probe(struct i2c_client *i2c)
705 {
706 	enum pca9450_chip_type type = (unsigned int)(uintptr_t)
707 				      of_device_get_match_data(&i2c->dev);
708 	const struct pca9450_regulator_desc	*regulator_desc;
709 	struct regulator_config config = { };
710 	struct pca9450 *pca9450;
711 	unsigned int device_id, i;
712 	unsigned int reset_ctrl;
713 	int ret;
714 
715 	if (!i2c->irq) {
716 		dev_err(&i2c->dev, "No IRQ configured?\n");
717 		return -EINVAL;
718 	}
719 
720 	pca9450 = devm_kzalloc(&i2c->dev, sizeof(struct pca9450), GFP_KERNEL);
721 	if (!pca9450)
722 		return -ENOMEM;
723 
724 	switch (type) {
725 	case PCA9450_TYPE_PCA9450A:
726 		regulator_desc = pca9450a_regulators;
727 		pca9450->rcnt = ARRAY_SIZE(pca9450a_regulators);
728 		break;
729 	case PCA9450_TYPE_PCA9450BC:
730 		regulator_desc = pca9450bc_regulators;
731 		pca9450->rcnt = ARRAY_SIZE(pca9450bc_regulators);
732 		break;
733 	default:
734 		dev_err(&i2c->dev, "Unknown device type");
735 		return -EINVAL;
736 	}
737 
738 	pca9450->irq = i2c->irq;
739 	pca9450->type = type;
740 	pca9450->dev = &i2c->dev;
741 
742 	dev_set_drvdata(&i2c->dev, pca9450);
743 
744 	pca9450->regmap = devm_regmap_init_i2c(i2c,
745 					       &pca9450_regmap_config);
746 	if (IS_ERR(pca9450->regmap)) {
747 		dev_err(&i2c->dev, "regmap initialization failed\n");
748 		return PTR_ERR(pca9450->regmap);
749 	}
750 
751 	ret = regmap_read(pca9450->regmap, PCA9450_REG_DEV_ID, &device_id);
752 	if (ret) {
753 		dev_err(&i2c->dev, "Read device id error\n");
754 		return ret;
755 	}
756 
757 	/* Check your board and dts for match the right pmic */
758 	if (((device_id >> 4) != 0x1 && type == PCA9450_TYPE_PCA9450A) ||
759 	    ((device_id >> 4) != 0x3 && type == PCA9450_TYPE_PCA9450BC)) {
760 		dev_err(&i2c->dev, "Device id(%x) mismatched\n",
761 			device_id >> 4);
762 		return -EINVAL;
763 	}
764 
765 	for (i = 0; i < pca9450->rcnt; i++) {
766 		const struct regulator_desc *desc;
767 		struct regulator_dev *rdev;
768 		const struct pca9450_regulator_desc *r;
769 
770 		r = &regulator_desc[i];
771 		desc = &r->desc;
772 
773 		config.regmap = pca9450->regmap;
774 		config.dev = pca9450->dev;
775 
776 		rdev = devm_regulator_register(pca9450->dev, desc, &config);
777 		if (IS_ERR(rdev)) {
778 			ret = PTR_ERR(rdev);
779 			dev_err(pca9450->dev,
780 				"Failed to register regulator(%s): %d\n",
781 				desc->name, ret);
782 			return ret;
783 		}
784 	}
785 
786 	ret = devm_request_threaded_irq(pca9450->dev, pca9450->irq, NULL,
787 					pca9450_irq_handler,
788 					(IRQF_TRIGGER_FALLING | IRQF_ONESHOT),
789 					"pca9450-irq", pca9450);
790 	if (ret != 0) {
791 		dev_err(pca9450->dev, "Failed to request IRQ: %d\n",
792 			pca9450->irq);
793 		return ret;
794 	}
795 	/* Unmask all interrupt except PWRON/WDOG/RSVD */
796 	ret = regmap_update_bits(pca9450->regmap, PCA9450_REG_INT1_MSK,
797 				IRQ_VR_FLT1 | IRQ_VR_FLT2 | IRQ_LOWVSYS |
798 				IRQ_THERM_105 | IRQ_THERM_125,
799 				IRQ_PWRON | IRQ_WDOGB | IRQ_RSVD);
800 	if (ret) {
801 		dev_err(&i2c->dev, "Unmask irq error\n");
802 		return ret;
803 	}
804 
805 	/* Clear PRESET_EN bit in BUCK123_DVS to use DVS registers */
806 	ret = regmap_clear_bits(pca9450->regmap, PCA9450_REG_BUCK123_DVS,
807 				BUCK123_PRESET_EN);
808 	if (ret) {
809 		dev_err(&i2c->dev, "Failed to clear PRESET_EN bit: %d\n", ret);
810 		return ret;
811 	}
812 
813 	if (of_property_read_bool(i2c->dev.of_node, "nxp,wdog_b-warm-reset"))
814 		reset_ctrl = WDOG_B_CFG_WARM;
815 	else
816 		reset_ctrl = WDOG_B_CFG_COLD_LDO12;
817 
818 	/* Set reset behavior on assertion of WDOG_B signal */
819 	ret = regmap_update_bits(pca9450->regmap, PCA9450_REG_RESET_CTRL,
820 				 WDOG_B_CFG_MASK, reset_ctrl);
821 	if (ret) {
822 		dev_err(&i2c->dev, "Failed to set WDOG_B reset behavior\n");
823 		return ret;
824 	}
825 
826 	if (of_property_read_bool(i2c->dev.of_node, "nxp,i2c-lt-enable")) {
827 		/* Enable I2C Level Translator */
828 		ret = regmap_update_bits(pca9450->regmap, PCA9450_REG_CONFIG2,
829 					 I2C_LT_MASK, I2C_LT_ON_STANDBY_RUN);
830 		if (ret) {
831 			dev_err(&i2c->dev,
832 				"Failed to enable I2C level translator\n");
833 			return ret;
834 		}
835 	}
836 
837 	/*
838 	 * The driver uses the LDO5CTRL_H register to control the LDO5 regulator.
839 	 * This is only valid if the SD_VSEL input of the PMIC is high. Let's
840 	 * check if the pin is available as GPIO and set it to high.
841 	 */
842 	pca9450->sd_vsel_gpio = gpiod_get_optional(pca9450->dev, "sd-vsel", GPIOD_OUT_HIGH);
843 
844 	if (IS_ERR(pca9450->sd_vsel_gpio)) {
845 		dev_err(&i2c->dev, "Failed to get SD_VSEL GPIO\n");
846 		return PTR_ERR(pca9450->sd_vsel_gpio);
847 	}
848 
849 	dev_info(&i2c->dev, "%s probed.\n",
850 		type == PCA9450_TYPE_PCA9450A ? "pca9450a" : "pca9450bc");
851 
852 	return 0;
853 }
854 
855 static const struct of_device_id pca9450_of_match[] = {
856 	{
857 		.compatible = "nxp,pca9450a",
858 		.data = (void *)PCA9450_TYPE_PCA9450A,
859 	},
860 	{
861 		.compatible = "nxp,pca9450b",
862 		.data = (void *)PCA9450_TYPE_PCA9450BC,
863 	},
864 	{
865 		.compatible = "nxp,pca9450c",
866 		.data = (void *)PCA9450_TYPE_PCA9450BC,
867 	},
868 	{ }
869 };
870 MODULE_DEVICE_TABLE(of, pca9450_of_match);
871 
872 static struct i2c_driver pca9450_i2c_driver = {
873 	.driver = {
874 		.name = "nxp-pca9450",
875 		.of_match_table = pca9450_of_match,
876 	},
877 	.probe_new = pca9450_i2c_probe,
878 };
879 
880 module_i2c_driver(pca9450_i2c_driver);
881 
882 MODULE_AUTHOR("Robin Gong <yibin.gong@nxp.com>");
883 MODULE_DESCRIPTION("NXP PCA9450 Power Management IC driver");
884 MODULE_LICENSE("GPL");
885