1 // SPDX-License-Identifier: GPL-2.0 2 // Copyright (C) 2018 ROHM Semiconductors 3 // bd71837-regulator.c ROHM BD71837MWV/BD71847MWV regulator driver 4 5 #include <linux/delay.h> 6 #include <linux/err.h> 7 #include <linux/interrupt.h> 8 #include <linux/kernel.h> 9 #include <linux/mfd/rohm-bd718x7.h> 10 #include <linux/module.h> 11 #include <linux/of.h> 12 #include <linux/platform_device.h> 13 #include <linux/regulator/driver.h> 14 #include <linux/regulator/machine.h> 15 #include <linux/regulator/of_regulator.h> 16 #include <linux/slab.h> 17 18 /* Typical regulator startup times as per data sheet in uS */ 19 #define BD71847_BUCK1_STARTUP_TIME 144 20 #define BD71847_BUCK2_STARTUP_TIME 162 21 #define BD71847_BUCK3_STARTUP_TIME 162 22 #define BD71847_BUCK4_STARTUP_TIME 240 23 #define BD71847_BUCK5_STARTUP_TIME 270 24 #define BD71847_BUCK6_STARTUP_TIME 200 25 #define BD71847_LDO1_STARTUP_TIME 440 26 #define BD71847_LDO2_STARTUP_TIME 370 27 #define BD71847_LDO3_STARTUP_TIME 310 28 #define BD71847_LDO4_STARTUP_TIME 400 29 #define BD71847_LDO5_STARTUP_TIME 530 30 #define BD71847_LDO6_STARTUP_TIME 400 31 32 #define BD71837_BUCK1_STARTUP_TIME 160 33 #define BD71837_BUCK2_STARTUP_TIME 180 34 #define BD71837_BUCK3_STARTUP_TIME 180 35 #define BD71837_BUCK4_STARTUP_TIME 180 36 #define BD71837_BUCK5_STARTUP_TIME 160 37 #define BD71837_BUCK6_STARTUP_TIME 240 38 #define BD71837_BUCK7_STARTUP_TIME 220 39 #define BD71837_BUCK8_STARTUP_TIME 200 40 #define BD71837_LDO1_STARTUP_TIME 440 41 #define BD71837_LDO2_STARTUP_TIME 370 42 #define BD71837_LDO3_STARTUP_TIME 310 43 #define BD71837_LDO4_STARTUP_TIME 400 44 #define BD71837_LDO5_STARTUP_TIME 310 45 #define BD71837_LDO6_STARTUP_TIME 400 46 #define BD71837_LDO7_STARTUP_TIME 530 47 48 /* 49 * BD718(37/47/50) have two "enable control modes". ON/OFF can either be 50 * controlled by software - or by PMIC internal HW state machine. Whether 51 * regulator should be under SW or HW control can be defined from device-tree. 52 * Let's provide separate ops for regulators to use depending on the "enable 53 * control mode". 54 */ 55 #define BD718XX_HWOPNAME(swopname) swopname##_hwcontrol 56 57 #define BD718XX_OPS(name, _list_voltage, _map_voltage, _set_voltage_sel, \ 58 _get_voltage_sel, _set_voltage_time_sel, _set_ramp_delay) \ 59 static const struct regulator_ops name = { \ 60 .enable = regulator_enable_regmap, \ 61 .disable = regulator_disable_regmap, \ 62 .is_enabled = regulator_is_enabled_regmap, \ 63 .list_voltage = (_list_voltage), \ 64 .map_voltage = (_map_voltage), \ 65 .set_voltage_sel = (_set_voltage_sel), \ 66 .get_voltage_sel = (_get_voltage_sel), \ 67 .set_voltage_time_sel = (_set_voltage_time_sel), \ 68 .set_ramp_delay = (_set_ramp_delay), \ 69 }; \ 70 \ 71 static const struct regulator_ops BD718XX_HWOPNAME(name) = { \ 72 .is_enabled = always_enabled_by_hwstate, \ 73 .list_voltage = (_list_voltage), \ 74 .map_voltage = (_map_voltage), \ 75 .set_voltage_sel = (_set_voltage_sel), \ 76 .get_voltage_sel = (_get_voltage_sel), \ 77 .set_voltage_time_sel = (_set_voltage_time_sel), \ 78 .set_ramp_delay = (_set_ramp_delay), \ 79 } \ 80 81 /* 82 * BUCK1/2/3/4 83 * BUCK1RAMPRATE[1:0] BUCK1 DVS ramp rate setting 84 * 00: 10.00mV/usec 10mV 1uS 85 * 01: 5.00mV/usec 10mV 2uS 86 * 10: 2.50mV/usec 10mV 4uS 87 * 11: 1.25mV/usec 10mV 8uS 88 */ 89 static const unsigned int bd718xx_ramp_delay[] = { 10000, 5000, 2500, 1250 }; 90 91 /* These functions are used when regulators are under HW state machine control. 92 * We assume PMIC is in RUN state because SW running and able to query the 93 * status. Most of the regulators have fixed ON or OFF state at RUN/IDLE so for 94 * them we just return a constant. BD71837 BUCK3 and BUCK4 are exceptions as 95 * they support configuring the ON/OFF state for RUN. 96 * 97 * Note for next hacker - these PMICs have a register where the HW state can be 98 * read. If assuming RUN appears to be false in your use-case - you can 99 * implement state reading (although that is not going to be atomic) before 100 * returning the enable state. 101 */ 102 static int always_enabled_by_hwstate(struct regulator_dev *rdev) 103 { 104 return 1; 105 } 106 107 static int never_enabled_by_hwstate(struct regulator_dev *rdev) 108 { 109 return 0; 110 } 111 112 static int bd71837_get_buck34_enable_hwctrl(struct regulator_dev *rdev) 113 { 114 int ret; 115 unsigned int val; 116 117 ret = regmap_read(rdev->regmap, rdev->desc->enable_reg, &val); 118 if (ret) 119 return ret; 120 121 return !!(BD718XX_BUCK_RUN_ON & val); 122 } 123 /* 124 * On BD71837 (not on BD71847, BD71850, ...) 125 * Bucks 1 to 4 support DVS. PWM mode is used when voltage is changed. 126 * Bucks 5 to 8 and LDOs can use PFM and must be disabled when voltage 127 * is changed. Hence we return -EBUSY for these if voltage is changed 128 * when BUCK/LDO is enabled. 129 * 130 * On BD71847, BD71850, ... The LDO voltage can be changed when LDO is 131 * enabled. But if voltage is increased the LDO power-good monitoring 132 * must be disabled for the duration of changing + 1mS to ensure voltage 133 * has reached the higher level before HW does next under voltage detection 134 * cycle. 135 */ 136 static int bd71837_set_voltage_sel_restricted(struct regulator_dev *rdev, 137 unsigned int sel) 138 { 139 if (rdev->desc->ops->is_enabled(rdev)) 140 return -EBUSY; 141 142 return regulator_set_voltage_sel_regmap(rdev, sel); 143 } 144 145 static void voltage_change_done(struct regulator_dev *rdev, unsigned int sel, 146 unsigned int *mask) 147 { 148 int ret; 149 150 if (*mask) { 151 /* 152 * Let's allow scheduling as we use I2C anyways. We just need to 153 * guarantee minimum of 1ms sleep - it shouldn't matter if we 154 * exceed it due to the scheduling. 155 */ 156 msleep(1); 157 /* 158 * Note for next hacker. The PWRGOOD should not be masked on 159 * BD71847 so we will just unconditionally enable detection 160 * when voltage is set. 161 * If someone want's to disable PWRGOOD he must implement 162 * caching and restoring the old value here. I am not 163 * aware of such use-cases so for the sake of the simplicity 164 * we just always enable PWRGOOD here. 165 */ 166 ret = regmap_update_bits(rdev->regmap, BD718XX_REG_MVRFLTMASK2, 167 *mask, 0); 168 if (ret) 169 dev_err(&rdev->dev, 170 "Failed to re-enable voltage monitoring (%d)\n", 171 ret); 172 } 173 } 174 175 static int voltage_change_prepare(struct regulator_dev *rdev, unsigned int sel, 176 unsigned int *mask) 177 { 178 int ret; 179 180 *mask = 0; 181 if (rdev->desc->ops->is_enabled(rdev)) { 182 int now, new; 183 184 now = rdev->desc->ops->get_voltage_sel(rdev); 185 if (now < 0) 186 return now; 187 188 now = rdev->desc->ops->list_voltage(rdev, now); 189 if (now < 0) 190 return now; 191 192 new = rdev->desc->ops->list_voltage(rdev, sel); 193 if (new < 0) 194 return new; 195 196 /* 197 * If we increase LDO voltage when LDO is enabled we need to 198 * disable the power-good detection until voltage has reached 199 * the new level. According to HW colleagues the maximum time 200 * it takes is 1000us. I assume that on systems with light load 201 * this might be less - and we could probably use DT to give 202 * system specific delay value if performance matters. 203 * 204 * Well, knowing we use I2C here and can add scheduling delays 205 * I don't think it is worth the hassle and I just add fixed 206 * 1ms sleep here (and allow scheduling). If this turns out to 207 * be a problem we can change it to delay and make the delay 208 * time configurable. 209 */ 210 if (new > now) { 211 int ldo_offset = rdev->desc->id - BD718XX_LDO1; 212 213 *mask = BD718XX_LDO1_VRMON80 << ldo_offset; 214 ret = regmap_update_bits(rdev->regmap, 215 BD718XX_REG_MVRFLTMASK2, 216 *mask, *mask); 217 if (ret) { 218 dev_err(&rdev->dev, 219 "Failed to stop voltage monitoring\n"); 220 return ret; 221 } 222 } 223 } 224 225 return 0; 226 } 227 228 static int bd718xx_set_voltage_sel_restricted(struct regulator_dev *rdev, 229 unsigned int sel) 230 { 231 int ret; 232 int mask; 233 234 ret = voltage_change_prepare(rdev, sel, &mask); 235 if (ret) 236 return ret; 237 238 ret = regulator_set_voltage_sel_regmap(rdev, sel); 239 voltage_change_done(rdev, sel, &mask); 240 241 return ret; 242 } 243 244 static int bd718xx_set_voltage_sel_pickable_restricted( 245 struct regulator_dev *rdev, unsigned int sel) 246 { 247 int ret; 248 int mask; 249 250 ret = voltage_change_prepare(rdev, sel, &mask); 251 if (ret) 252 return ret; 253 254 ret = regulator_set_voltage_sel_pickable_regmap(rdev, sel); 255 voltage_change_done(rdev, sel, &mask); 256 257 return ret; 258 } 259 260 static int bd71837_set_voltage_sel_pickable_restricted( 261 struct regulator_dev *rdev, unsigned int sel) 262 { 263 if (rdev->desc->ops->is_enabled(rdev)) 264 return -EBUSY; 265 266 return regulator_set_voltage_sel_pickable_regmap(rdev, sel); 267 } 268 269 /* 270 * OPS common for BD71847 and BD71850 271 */ 272 BD718XX_OPS(bd718xx_pickable_range_ldo_ops, 273 regulator_list_voltage_pickable_linear_range, NULL, 274 bd718xx_set_voltage_sel_pickable_restricted, 275 regulator_get_voltage_sel_pickable_regmap, NULL, NULL); 276 277 /* BD71847 and BD71850 LDO 5 is by default OFF at RUN state */ 278 static const struct regulator_ops bd718xx_ldo5_ops_hwstate = { 279 .is_enabled = never_enabled_by_hwstate, 280 .list_voltage = regulator_list_voltage_pickable_linear_range, 281 .set_voltage_sel = bd718xx_set_voltage_sel_pickable_restricted, 282 .get_voltage_sel = regulator_get_voltage_sel_pickable_regmap, 283 }; 284 285 BD718XX_OPS(bd718xx_pickable_range_buck_ops, 286 regulator_list_voltage_pickable_linear_range, NULL, 287 regulator_set_voltage_sel_pickable_regmap, 288 regulator_get_voltage_sel_pickable_regmap, 289 regulator_set_voltage_time_sel, NULL); 290 291 BD718XX_OPS(bd718xx_ldo_regulator_ops, regulator_list_voltage_linear_range, 292 NULL, bd718xx_set_voltage_sel_restricted, 293 regulator_get_voltage_sel_regmap, NULL, NULL); 294 295 BD718XX_OPS(bd718xx_ldo_regulator_nolinear_ops, regulator_list_voltage_table, 296 NULL, bd718xx_set_voltage_sel_restricted, 297 regulator_get_voltage_sel_regmap, NULL, NULL); 298 299 BD718XX_OPS(bd718xx_buck_regulator_ops, regulator_list_voltage_linear_range, 300 NULL, regulator_set_voltage_sel_regmap, 301 regulator_get_voltage_sel_regmap, regulator_set_voltage_time_sel, 302 NULL); 303 304 BD718XX_OPS(bd718xx_buck_regulator_nolinear_ops, regulator_list_voltage_table, 305 regulator_map_voltage_ascend, regulator_set_voltage_sel_regmap, 306 regulator_get_voltage_sel_regmap, regulator_set_voltage_time_sel, 307 NULL); 308 309 /* 310 * OPS for BD71837 311 */ 312 BD718XX_OPS(bd71837_pickable_range_ldo_ops, 313 regulator_list_voltage_pickable_linear_range, NULL, 314 bd71837_set_voltage_sel_pickable_restricted, 315 regulator_get_voltage_sel_pickable_regmap, NULL, NULL); 316 317 BD718XX_OPS(bd71837_pickable_range_buck_ops, 318 regulator_list_voltage_pickable_linear_range, NULL, 319 bd71837_set_voltage_sel_pickable_restricted, 320 regulator_get_voltage_sel_pickable_regmap, 321 regulator_set_voltage_time_sel, NULL); 322 323 BD718XX_OPS(bd71837_ldo_regulator_ops, regulator_list_voltage_linear_range, 324 NULL, bd71837_set_voltage_sel_restricted, 325 regulator_get_voltage_sel_regmap, NULL, NULL); 326 327 BD718XX_OPS(bd71837_ldo_regulator_nolinear_ops, regulator_list_voltage_table, 328 NULL, bd71837_set_voltage_sel_restricted, 329 regulator_get_voltage_sel_regmap, NULL, NULL); 330 331 BD718XX_OPS(bd71837_buck_regulator_ops, regulator_list_voltage_linear_range, 332 NULL, bd71837_set_voltage_sel_restricted, 333 regulator_get_voltage_sel_regmap, regulator_set_voltage_time_sel, 334 NULL); 335 336 BD718XX_OPS(bd71837_buck_regulator_nolinear_ops, regulator_list_voltage_table, 337 regulator_map_voltage_ascend, bd71837_set_voltage_sel_restricted, 338 regulator_get_voltage_sel_regmap, regulator_set_voltage_time_sel, 339 NULL); 340 /* 341 * BD71837 bucks 3 and 4 support defining their enable/disable state also 342 * when buck enable state is under HW state machine control. In that case the 343 * bit [2] in CTRL register is used to indicate if regulator should be ON. 344 */ 345 static const struct regulator_ops bd71837_buck34_ops_hwctrl = { 346 .is_enabled = bd71837_get_buck34_enable_hwctrl, 347 .list_voltage = regulator_list_voltage_linear_range, 348 .set_voltage_sel = regulator_set_voltage_sel_regmap, 349 .get_voltage_sel = regulator_get_voltage_sel_regmap, 350 .set_voltage_time_sel = regulator_set_voltage_time_sel, 351 .set_ramp_delay = regulator_set_ramp_delay_regmap, 352 }; 353 354 /* 355 * OPS for all of the ICs - BD718(37/47/50) 356 */ 357 BD718XX_OPS(bd718xx_dvs_buck_regulator_ops, regulator_list_voltage_linear_range, 358 NULL, regulator_set_voltage_sel_regmap, 359 regulator_get_voltage_sel_regmap, regulator_set_voltage_time_sel, 360 /* bd718xx_buck1234_set_ramp_delay */ regulator_set_ramp_delay_regmap); 361 362 /* 363 * BD71837 BUCK1/2/3/4 364 * BD71847 BUCK1/2 365 * 0.70 to 1.30V (10mV step) 366 */ 367 static const struct linear_range bd718xx_dvs_buck_volts[] = { 368 REGULATOR_LINEAR_RANGE(700000, 0x00, 0x3C, 10000), 369 REGULATOR_LINEAR_RANGE(1300000, 0x3D, 0x3F, 0), 370 }; 371 372 /* 373 * BD71837 BUCK5 374 * 0.7V to 1.35V (range 0) 375 * and 376 * 0.675 to 1.325 (range 1) 377 */ 378 static const struct linear_range bd71837_buck5_volts[] = { 379 /* Ranges when VOLT_SEL bit is 0 */ 380 REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000), 381 REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000), 382 REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000), 383 /* Ranges when VOLT_SEL bit is 1 */ 384 REGULATOR_LINEAR_RANGE(675000, 0x0, 0x3, 100000), 385 REGULATOR_LINEAR_RANGE(1025000, 0x4, 0x5, 50000), 386 REGULATOR_LINEAR_RANGE(1175000, 0x6, 0x7, 150000), 387 }; 388 389 /* 390 * Range selector for first 3 linear ranges is 0x0 391 * and 0x1 for last 3 ranges. 392 */ 393 static const unsigned int bd71837_buck5_volt_range_sel[] = { 394 0x0, 0x0, 0x0, 0x80, 0x80, 0x80 395 }; 396 397 /* 398 * BD71847 BUCK3 399 */ 400 static const struct linear_range bd71847_buck3_volts[] = { 401 /* Ranges when VOLT_SEL bits are 00 */ 402 REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000), 403 REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000), 404 REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000), 405 /* Ranges when VOLT_SEL bits are 01 */ 406 REGULATOR_LINEAR_RANGE(550000, 0x0, 0x7, 50000), 407 /* Ranges when VOLT_SEL bits are 11 */ 408 REGULATOR_LINEAR_RANGE(675000, 0x0, 0x3, 100000), 409 REGULATOR_LINEAR_RANGE(1025000, 0x4, 0x5, 50000), 410 REGULATOR_LINEAR_RANGE(1175000, 0x6, 0x7, 150000), 411 }; 412 413 static const unsigned int bd71847_buck3_volt_range_sel[] = { 414 0x0, 0x0, 0x0, 0x40, 0x80, 0x80, 0x80 415 }; 416 417 static const struct linear_range bd71847_buck4_volts[] = { 418 REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000), 419 REGULATOR_LINEAR_RANGE(2600000, 0x00, 0x03, 100000), 420 }; 421 422 static const unsigned int bd71847_buck4_volt_range_sel[] = { 0x0, 0x40 }; 423 424 /* 425 * BUCK6 426 * 3.0V to 3.3V (step 100mV) 427 */ 428 static const struct linear_range bd71837_buck6_volts[] = { 429 REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000), 430 }; 431 432 /* 433 * BD71837 BUCK7 434 * BD71847 BUCK5 435 * 000 = 1.605V 436 * 001 = 1.695V 437 * 010 = 1.755V 438 * 011 = 1.8V (Initial) 439 * 100 = 1.845V 440 * 101 = 1.905V 441 * 110 = 1.95V 442 * 111 = 1.995V 443 */ 444 static const unsigned int bd718xx_3rd_nodvs_buck_volts[] = { 445 1605000, 1695000, 1755000, 1800000, 1845000, 1905000, 1950000, 1995000 446 }; 447 448 /* 449 * BUCK8 450 * 0.8V to 1.40V (step 10mV) 451 */ 452 static const struct linear_range bd718xx_4th_nodvs_buck_volts[] = { 453 REGULATOR_LINEAR_RANGE(800000, 0x00, 0x3C, 10000), 454 }; 455 456 /* 457 * LDO1 458 * 3.0 to 3.3V (100mV step) 459 */ 460 static const struct linear_range bd718xx_ldo1_volts[] = { 461 REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000), 462 REGULATOR_LINEAR_RANGE(1600000, 0x00, 0x03, 100000), 463 }; 464 465 static const unsigned int bd718xx_ldo1_volt_range_sel[] = { 0x0, 0x20 }; 466 467 /* 468 * LDO2 469 * 0.8 or 0.9V 470 */ 471 static const unsigned int ldo_2_volts[] = { 472 900000, 800000 473 }; 474 475 /* 476 * LDO3 477 * 1.8 to 3.3V (100mV step) 478 */ 479 static const struct linear_range bd718xx_ldo3_volts[] = { 480 REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000), 481 }; 482 483 /* 484 * LDO4 485 * 0.9 to 1.8V (100mV step) 486 */ 487 static const struct linear_range bd718xx_ldo4_volts[] = { 488 REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000), 489 }; 490 491 /* 492 * LDO5 for BD71837 493 * 1.8 to 3.3V (100mV step) 494 */ 495 static const struct linear_range bd71837_ldo5_volts[] = { 496 REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000), 497 }; 498 499 /* 500 * LDO5 for BD71837 501 * 1.8 to 3.3V (100mV step) 502 */ 503 static const struct linear_range bd71847_ldo5_volts[] = { 504 REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000), 505 REGULATOR_LINEAR_RANGE(800000, 0x00, 0x0F, 100000), 506 }; 507 508 static const unsigned int bd71847_ldo5_volt_range_sel[] = { 0x0, 0x20 }; 509 510 /* 511 * LDO6 512 * 0.9 to 1.8V (100mV step) 513 */ 514 static const struct linear_range bd718xx_ldo6_volts[] = { 515 REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000), 516 }; 517 518 /* 519 * LDO7 520 * 1.8 to 3.3V (100mV step) 521 */ 522 static const struct linear_range bd71837_ldo7_volts[] = { 523 REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000), 524 }; 525 526 struct reg_init { 527 unsigned int reg; 528 unsigned int mask; 529 unsigned int val; 530 }; 531 struct bd718xx_regulator_data { 532 struct regulator_desc desc; 533 const struct rohm_dvs_config dvs; 534 const struct reg_init init; 535 const struct reg_init *additional_inits; 536 int additional_init_amnt; 537 }; 538 539 /* 540 * There is a HW quirk in BD71837. The shutdown sequence timings for 541 * bucks/LDOs which are controlled via register interface are changed. 542 * At PMIC poweroff the voltage for BUCK6/7 is cut immediately at the 543 * beginning of shut-down sequence. As bucks 6 and 7 are parent 544 * supplies for LDO5 and LDO6 - this causes LDO5/6 voltage 545 * monitoring to errorneously detect under voltage and force PMIC to 546 * emergency state instead of poweroff. In order to avoid this we 547 * disable voltage monitoring for LDO5 and LDO6 548 */ 549 static const struct reg_init bd71837_ldo5_inits[] = { 550 { 551 .reg = BD718XX_REG_MVRFLTMASK2, 552 .mask = BD718XX_LDO5_VRMON80, 553 .val = BD718XX_LDO5_VRMON80, 554 }, 555 }; 556 557 static const struct reg_init bd71837_ldo6_inits[] = { 558 { 559 .reg = BD718XX_REG_MVRFLTMASK2, 560 .mask = BD718XX_LDO6_VRMON80, 561 .val = BD718XX_LDO6_VRMON80, 562 }, 563 }; 564 565 static int buck_set_hw_dvs_levels(struct device_node *np, 566 const struct regulator_desc *desc, 567 struct regulator_config *cfg) 568 { 569 struct bd718xx_regulator_data *data; 570 571 data = container_of(desc, struct bd718xx_regulator_data, desc); 572 573 return rohm_regulator_set_dvs_levels(&data->dvs, np, desc, cfg->regmap); 574 } 575 576 static const struct regulator_ops *bd71847_swcontrol_ops[] = { 577 &bd718xx_dvs_buck_regulator_ops, &bd718xx_dvs_buck_regulator_ops, 578 &bd718xx_pickable_range_buck_ops, &bd718xx_pickable_range_buck_ops, 579 &bd718xx_buck_regulator_nolinear_ops, &bd718xx_buck_regulator_ops, 580 &bd718xx_pickable_range_ldo_ops, &bd718xx_ldo_regulator_nolinear_ops, 581 &bd718xx_ldo_regulator_ops, &bd718xx_ldo_regulator_ops, 582 &bd718xx_pickable_range_ldo_ops, &bd718xx_ldo_regulator_ops, 583 }; 584 585 static const struct regulator_ops *bd71847_hwcontrol_ops[] = { 586 &BD718XX_HWOPNAME(bd718xx_dvs_buck_regulator_ops), 587 &BD718XX_HWOPNAME(bd718xx_dvs_buck_regulator_ops), 588 &BD718XX_HWOPNAME(bd718xx_pickable_range_buck_ops), 589 &BD718XX_HWOPNAME(bd718xx_pickable_range_buck_ops), 590 &BD718XX_HWOPNAME(bd718xx_buck_regulator_nolinear_ops), 591 &BD718XX_HWOPNAME(bd718xx_buck_regulator_ops), 592 &BD718XX_HWOPNAME(bd718xx_pickable_range_ldo_ops), 593 &BD718XX_HWOPNAME(bd718xx_ldo_regulator_nolinear_ops), 594 &BD718XX_HWOPNAME(bd718xx_ldo_regulator_ops), 595 &BD718XX_HWOPNAME(bd718xx_ldo_regulator_ops), 596 &bd718xx_ldo5_ops_hwstate, 597 &BD718XX_HWOPNAME(bd718xx_ldo_regulator_ops), 598 }; 599 600 static struct bd718xx_regulator_data bd71847_regulators[] = { 601 { 602 .desc = { 603 .name = "buck1", 604 .of_match = of_match_ptr("BUCK1"), 605 .regulators_node = of_match_ptr("regulators"), 606 .id = BD718XX_BUCK1, 607 .type = REGULATOR_VOLTAGE, 608 .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM, 609 .linear_ranges = bd718xx_dvs_buck_volts, 610 .n_linear_ranges = 611 ARRAY_SIZE(bd718xx_dvs_buck_volts), 612 .vsel_reg = BD718XX_REG_BUCK1_VOLT_RUN, 613 .vsel_mask = DVS_BUCK_RUN_MASK, 614 .enable_reg = BD718XX_REG_BUCK1_CTRL, 615 .enable_mask = BD718XX_BUCK_EN, 616 .enable_time = BD71847_BUCK1_STARTUP_TIME, 617 .owner = THIS_MODULE, 618 .ramp_delay_table = bd718xx_ramp_delay, 619 .n_ramp_values = ARRAY_SIZE(bd718xx_ramp_delay), 620 .ramp_reg = BD718XX_REG_BUCK1_CTRL, 621 .ramp_mask = BUCK_RAMPRATE_MASK, 622 .of_parse_cb = buck_set_hw_dvs_levels, 623 }, 624 .dvs = { 625 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE | 626 ROHM_DVS_LEVEL_SUSPEND, 627 .run_reg = BD718XX_REG_BUCK1_VOLT_RUN, 628 .run_mask = DVS_BUCK_RUN_MASK, 629 .idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE, 630 .idle_mask = DVS_BUCK_RUN_MASK, 631 .suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP, 632 .suspend_mask = DVS_BUCK_RUN_MASK, 633 }, 634 .init = { 635 .reg = BD718XX_REG_BUCK1_CTRL, 636 .mask = BD718XX_BUCK_SEL, 637 .val = BD718XX_BUCK_SEL, 638 }, 639 }, 640 { 641 .desc = { 642 .name = "buck2", 643 .of_match = of_match_ptr("BUCK2"), 644 .regulators_node = of_match_ptr("regulators"), 645 .id = BD718XX_BUCK2, 646 .type = REGULATOR_VOLTAGE, 647 .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM, 648 .linear_ranges = bd718xx_dvs_buck_volts, 649 .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts), 650 .vsel_reg = BD718XX_REG_BUCK2_VOLT_RUN, 651 .vsel_mask = DVS_BUCK_RUN_MASK, 652 .enable_reg = BD718XX_REG_BUCK2_CTRL, 653 .enable_mask = BD718XX_BUCK_EN, 654 .enable_time = BD71847_BUCK2_STARTUP_TIME, 655 .ramp_delay_table = bd718xx_ramp_delay, 656 .n_ramp_values = ARRAY_SIZE(bd718xx_ramp_delay), 657 .ramp_reg = BD718XX_REG_BUCK2_CTRL, 658 .ramp_mask = BUCK_RAMPRATE_MASK, 659 .owner = THIS_MODULE, 660 .of_parse_cb = buck_set_hw_dvs_levels, 661 }, 662 .dvs = { 663 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE, 664 .run_reg = BD718XX_REG_BUCK2_VOLT_RUN, 665 .run_mask = DVS_BUCK_RUN_MASK, 666 .idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE, 667 .idle_mask = DVS_BUCK_RUN_MASK, 668 }, 669 .init = { 670 .reg = BD718XX_REG_BUCK2_CTRL, 671 .mask = BD718XX_BUCK_SEL, 672 .val = BD718XX_BUCK_SEL, 673 }, 674 }, 675 { 676 .desc = { 677 .name = "buck3", 678 .of_match = of_match_ptr("BUCK3"), 679 .regulators_node = of_match_ptr("regulators"), 680 .id = BD718XX_BUCK3, 681 .type = REGULATOR_VOLTAGE, 682 .n_voltages = BD71847_BUCK3_VOLTAGE_NUM, 683 .linear_ranges = bd71847_buck3_volts, 684 .n_linear_ranges = 685 ARRAY_SIZE(bd71847_buck3_volts), 686 .vsel_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT, 687 .vsel_mask = BD718XX_1ST_NODVS_BUCK_MASK, 688 .vsel_range_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT, 689 .vsel_range_mask = BD71847_BUCK3_RANGE_MASK, 690 .linear_range_selectors = bd71847_buck3_volt_range_sel, 691 .enable_reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL, 692 .enable_mask = BD718XX_BUCK_EN, 693 .enable_time = BD71847_BUCK3_STARTUP_TIME, 694 .owner = THIS_MODULE, 695 }, 696 .init = { 697 .reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL, 698 .mask = BD718XX_BUCK_SEL, 699 .val = BD718XX_BUCK_SEL, 700 }, 701 }, 702 { 703 .desc = { 704 .name = "buck4", 705 .of_match = of_match_ptr("BUCK4"), 706 .regulators_node = of_match_ptr("regulators"), 707 .id = BD718XX_BUCK4, 708 .type = REGULATOR_VOLTAGE, 709 .n_voltages = BD71847_BUCK4_VOLTAGE_NUM, 710 .linear_ranges = bd71847_buck4_volts, 711 .n_linear_ranges = 712 ARRAY_SIZE(bd71847_buck4_volts), 713 .enable_reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL, 714 .vsel_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT, 715 .vsel_mask = BD71847_BUCK4_MASK, 716 .vsel_range_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT, 717 .vsel_range_mask = BD71847_BUCK4_RANGE_MASK, 718 .linear_range_selectors = bd71847_buck4_volt_range_sel, 719 .enable_mask = BD718XX_BUCK_EN, 720 .enable_time = BD71847_BUCK4_STARTUP_TIME, 721 .owner = THIS_MODULE, 722 }, 723 .init = { 724 .reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL, 725 .mask = BD718XX_BUCK_SEL, 726 .val = BD718XX_BUCK_SEL, 727 }, 728 }, 729 { 730 .desc = { 731 .name = "buck5", 732 .of_match = of_match_ptr("BUCK5"), 733 .regulators_node = of_match_ptr("regulators"), 734 .id = BD718XX_BUCK5, 735 .type = REGULATOR_VOLTAGE, 736 .volt_table = &bd718xx_3rd_nodvs_buck_volts[0], 737 .n_voltages = ARRAY_SIZE(bd718xx_3rd_nodvs_buck_volts), 738 .vsel_reg = BD718XX_REG_3RD_NODVS_BUCK_VOLT, 739 .vsel_mask = BD718XX_3RD_NODVS_BUCK_MASK, 740 .enable_reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL, 741 .enable_mask = BD718XX_BUCK_EN, 742 .enable_time = BD71847_BUCK5_STARTUP_TIME, 743 .owner = THIS_MODULE, 744 }, 745 .init = { 746 .reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL, 747 .mask = BD718XX_BUCK_SEL, 748 .val = BD718XX_BUCK_SEL, 749 }, 750 }, 751 { 752 .desc = { 753 .name = "buck6", 754 .of_match = of_match_ptr("BUCK6"), 755 .regulators_node = of_match_ptr("regulators"), 756 .id = BD718XX_BUCK6, 757 .type = REGULATOR_VOLTAGE, 758 .n_voltages = BD718XX_4TH_NODVS_BUCK_VOLTAGE_NUM, 759 .linear_ranges = bd718xx_4th_nodvs_buck_volts, 760 .n_linear_ranges = 761 ARRAY_SIZE(bd718xx_4th_nodvs_buck_volts), 762 .vsel_reg = BD718XX_REG_4TH_NODVS_BUCK_VOLT, 763 .vsel_mask = BD718XX_4TH_NODVS_BUCK_MASK, 764 .enable_reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL, 765 .enable_mask = BD718XX_BUCK_EN, 766 .enable_time = BD71847_BUCK6_STARTUP_TIME, 767 .owner = THIS_MODULE, 768 }, 769 .init = { 770 .reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL, 771 .mask = BD718XX_BUCK_SEL, 772 .val = BD718XX_BUCK_SEL, 773 }, 774 }, 775 { 776 .desc = { 777 .name = "ldo1", 778 .of_match = of_match_ptr("LDO1"), 779 .regulators_node = of_match_ptr("regulators"), 780 .id = BD718XX_LDO1, 781 .type = REGULATOR_VOLTAGE, 782 .n_voltages = BD718XX_LDO1_VOLTAGE_NUM, 783 .linear_ranges = bd718xx_ldo1_volts, 784 .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo1_volts), 785 .vsel_reg = BD718XX_REG_LDO1_VOLT, 786 .vsel_mask = BD718XX_LDO1_MASK, 787 .vsel_range_reg = BD718XX_REG_LDO1_VOLT, 788 .vsel_range_mask = BD718XX_LDO1_RANGE_MASK, 789 .linear_range_selectors = bd718xx_ldo1_volt_range_sel, 790 .enable_reg = BD718XX_REG_LDO1_VOLT, 791 .enable_mask = BD718XX_LDO_EN, 792 .enable_time = BD71847_LDO1_STARTUP_TIME, 793 .owner = THIS_MODULE, 794 }, 795 .init = { 796 .reg = BD718XX_REG_LDO1_VOLT, 797 .mask = BD718XX_LDO_SEL, 798 .val = BD718XX_LDO_SEL, 799 }, 800 }, 801 { 802 .desc = { 803 .name = "ldo2", 804 .of_match = of_match_ptr("LDO2"), 805 .regulators_node = of_match_ptr("regulators"), 806 .id = BD718XX_LDO2, 807 .type = REGULATOR_VOLTAGE, 808 .volt_table = &ldo_2_volts[0], 809 .vsel_reg = BD718XX_REG_LDO2_VOLT, 810 .vsel_mask = BD718XX_LDO2_MASK, 811 .n_voltages = ARRAY_SIZE(ldo_2_volts), 812 .enable_reg = BD718XX_REG_LDO2_VOLT, 813 .enable_mask = BD718XX_LDO_EN, 814 .enable_time = BD71847_LDO2_STARTUP_TIME, 815 .owner = THIS_MODULE, 816 }, 817 .init = { 818 .reg = BD718XX_REG_LDO2_VOLT, 819 .mask = BD718XX_LDO_SEL, 820 .val = BD718XX_LDO_SEL, 821 }, 822 }, 823 { 824 .desc = { 825 .name = "ldo3", 826 .of_match = of_match_ptr("LDO3"), 827 .regulators_node = of_match_ptr("regulators"), 828 .id = BD718XX_LDO3, 829 .type = REGULATOR_VOLTAGE, 830 .n_voltages = BD718XX_LDO3_VOLTAGE_NUM, 831 .linear_ranges = bd718xx_ldo3_volts, 832 .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo3_volts), 833 .vsel_reg = BD718XX_REG_LDO3_VOLT, 834 .vsel_mask = BD718XX_LDO3_MASK, 835 .enable_reg = BD718XX_REG_LDO3_VOLT, 836 .enable_mask = BD718XX_LDO_EN, 837 .enable_time = BD71847_LDO3_STARTUP_TIME, 838 .owner = THIS_MODULE, 839 }, 840 .init = { 841 .reg = BD718XX_REG_LDO3_VOLT, 842 .mask = BD718XX_LDO_SEL, 843 .val = BD718XX_LDO_SEL, 844 }, 845 }, 846 { 847 .desc = { 848 .name = "ldo4", 849 .of_match = of_match_ptr("LDO4"), 850 .regulators_node = of_match_ptr("regulators"), 851 .id = BD718XX_LDO4, 852 .type = REGULATOR_VOLTAGE, 853 .n_voltages = BD718XX_LDO4_VOLTAGE_NUM, 854 .linear_ranges = bd718xx_ldo4_volts, 855 .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo4_volts), 856 .vsel_reg = BD718XX_REG_LDO4_VOLT, 857 .vsel_mask = BD718XX_LDO4_MASK, 858 .enable_reg = BD718XX_REG_LDO4_VOLT, 859 .enable_mask = BD718XX_LDO_EN, 860 .enable_time = BD71847_LDO4_STARTUP_TIME, 861 .owner = THIS_MODULE, 862 }, 863 .init = { 864 .reg = BD718XX_REG_LDO4_VOLT, 865 .mask = BD718XX_LDO_SEL, 866 .val = BD718XX_LDO_SEL, 867 }, 868 }, 869 { 870 .desc = { 871 .name = "ldo5", 872 .of_match = of_match_ptr("LDO5"), 873 .regulators_node = of_match_ptr("regulators"), 874 .id = BD718XX_LDO5, 875 .type = REGULATOR_VOLTAGE, 876 .n_voltages = BD71847_LDO5_VOLTAGE_NUM, 877 .linear_ranges = bd71847_ldo5_volts, 878 .n_linear_ranges = ARRAY_SIZE(bd71847_ldo5_volts), 879 .vsel_reg = BD718XX_REG_LDO5_VOLT, 880 .vsel_mask = BD71847_LDO5_MASK, 881 .vsel_range_reg = BD718XX_REG_LDO5_VOLT, 882 .vsel_range_mask = BD71847_LDO5_RANGE_MASK, 883 .linear_range_selectors = bd71847_ldo5_volt_range_sel, 884 .enable_reg = BD718XX_REG_LDO5_VOLT, 885 .enable_mask = BD718XX_LDO_EN, 886 .enable_time = BD71847_LDO5_STARTUP_TIME, 887 .owner = THIS_MODULE, 888 }, 889 .init = { 890 .reg = BD718XX_REG_LDO5_VOLT, 891 .mask = BD718XX_LDO_SEL, 892 .val = BD718XX_LDO_SEL, 893 }, 894 }, 895 { 896 .desc = { 897 .name = "ldo6", 898 .of_match = of_match_ptr("LDO6"), 899 .regulators_node = of_match_ptr("regulators"), 900 .id = BD718XX_LDO6, 901 .type = REGULATOR_VOLTAGE, 902 .n_voltages = BD718XX_LDO6_VOLTAGE_NUM, 903 .linear_ranges = bd718xx_ldo6_volts, 904 .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo6_volts), 905 /* LDO6 is supplied by buck5 */ 906 .supply_name = "buck5", 907 .vsel_reg = BD718XX_REG_LDO6_VOLT, 908 .vsel_mask = BD718XX_LDO6_MASK, 909 .enable_reg = BD718XX_REG_LDO6_VOLT, 910 .enable_mask = BD718XX_LDO_EN, 911 .enable_time = BD71847_LDO6_STARTUP_TIME, 912 .owner = THIS_MODULE, 913 }, 914 .init = { 915 .reg = BD718XX_REG_LDO6_VOLT, 916 .mask = BD718XX_LDO_SEL, 917 .val = BD718XX_LDO_SEL, 918 }, 919 }, 920 }; 921 922 static const struct regulator_ops *bd71837_swcontrol_ops[] = { 923 &bd718xx_dvs_buck_regulator_ops, &bd718xx_dvs_buck_regulator_ops, 924 &bd718xx_dvs_buck_regulator_ops, &bd718xx_dvs_buck_regulator_ops, 925 &bd71837_pickable_range_buck_ops, &bd71837_buck_regulator_ops, 926 &bd71837_buck_regulator_nolinear_ops, &bd71837_buck_regulator_ops, 927 &bd71837_pickable_range_ldo_ops, &bd71837_ldo_regulator_nolinear_ops, 928 &bd71837_ldo_regulator_ops, &bd71837_ldo_regulator_ops, 929 &bd71837_ldo_regulator_ops, &bd71837_ldo_regulator_ops, 930 &bd71837_ldo_regulator_ops, 931 }; 932 933 static const struct regulator_ops *bd71837_hwcontrol_ops[] = { 934 &BD718XX_HWOPNAME(bd718xx_dvs_buck_regulator_ops), 935 &BD718XX_HWOPNAME(bd718xx_dvs_buck_regulator_ops), 936 &bd71837_buck34_ops_hwctrl, &bd71837_buck34_ops_hwctrl, 937 &BD718XX_HWOPNAME(bd71837_pickable_range_buck_ops), 938 &BD718XX_HWOPNAME(bd71837_buck_regulator_ops), 939 &BD718XX_HWOPNAME(bd71837_buck_regulator_nolinear_ops), 940 &BD718XX_HWOPNAME(bd71837_buck_regulator_ops), 941 &BD718XX_HWOPNAME(bd71837_pickable_range_ldo_ops), 942 &BD718XX_HWOPNAME(bd71837_ldo_regulator_nolinear_ops), 943 &BD718XX_HWOPNAME(bd71837_ldo_regulator_ops), 944 &BD718XX_HWOPNAME(bd71837_ldo_regulator_ops), 945 &BD718XX_HWOPNAME(bd71837_ldo_regulator_ops), 946 &BD718XX_HWOPNAME(bd71837_ldo_regulator_ops), 947 &BD718XX_HWOPNAME(bd71837_ldo_regulator_ops), 948 }; 949 950 static struct bd718xx_regulator_data bd71837_regulators[] = { 951 { 952 .desc = { 953 .name = "buck1", 954 .of_match = of_match_ptr("BUCK1"), 955 .regulators_node = of_match_ptr("regulators"), 956 .id = BD718XX_BUCK1, 957 .type = REGULATOR_VOLTAGE, 958 .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM, 959 .linear_ranges = bd718xx_dvs_buck_volts, 960 .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts), 961 .vsel_reg = BD718XX_REG_BUCK1_VOLT_RUN, 962 .vsel_mask = DVS_BUCK_RUN_MASK, 963 .enable_reg = BD718XX_REG_BUCK1_CTRL, 964 .enable_mask = BD718XX_BUCK_EN, 965 .enable_time = BD71837_BUCK1_STARTUP_TIME, 966 .ramp_delay_table = bd718xx_ramp_delay, 967 .n_ramp_values = ARRAY_SIZE(bd718xx_ramp_delay), 968 .ramp_reg = BD718XX_REG_BUCK1_CTRL, 969 .ramp_mask = BUCK_RAMPRATE_MASK, 970 .owner = THIS_MODULE, 971 .of_parse_cb = buck_set_hw_dvs_levels, 972 }, 973 .dvs = { 974 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE | 975 ROHM_DVS_LEVEL_SUSPEND, 976 .run_reg = BD718XX_REG_BUCK1_VOLT_RUN, 977 .run_mask = DVS_BUCK_RUN_MASK, 978 .idle_reg = BD718XX_REG_BUCK1_VOLT_IDLE, 979 .idle_mask = DVS_BUCK_RUN_MASK, 980 .suspend_reg = BD718XX_REG_BUCK1_VOLT_SUSP, 981 .suspend_mask = DVS_BUCK_RUN_MASK, 982 }, 983 .init = { 984 .reg = BD718XX_REG_BUCK1_CTRL, 985 .mask = BD718XX_BUCK_SEL, 986 .val = BD718XX_BUCK_SEL, 987 }, 988 }, 989 { 990 .desc = { 991 .name = "buck2", 992 .of_match = of_match_ptr("BUCK2"), 993 .regulators_node = of_match_ptr("regulators"), 994 .id = BD718XX_BUCK2, 995 .type = REGULATOR_VOLTAGE, 996 .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM, 997 .linear_ranges = bd718xx_dvs_buck_volts, 998 .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts), 999 .vsel_reg = BD718XX_REG_BUCK2_VOLT_RUN, 1000 .vsel_mask = DVS_BUCK_RUN_MASK, 1001 .enable_reg = BD718XX_REG_BUCK2_CTRL, 1002 .enable_mask = BD718XX_BUCK_EN, 1003 .enable_time = BD71837_BUCK2_STARTUP_TIME, 1004 .ramp_delay_table = bd718xx_ramp_delay, 1005 .n_ramp_values = ARRAY_SIZE(bd718xx_ramp_delay), 1006 .ramp_reg = BD718XX_REG_BUCK2_CTRL, 1007 .ramp_mask = BUCK_RAMPRATE_MASK, 1008 .owner = THIS_MODULE, 1009 .of_parse_cb = buck_set_hw_dvs_levels, 1010 }, 1011 .dvs = { 1012 .level_map = ROHM_DVS_LEVEL_RUN | ROHM_DVS_LEVEL_IDLE, 1013 .run_reg = BD718XX_REG_BUCK2_VOLT_RUN, 1014 .run_mask = DVS_BUCK_RUN_MASK, 1015 .idle_reg = BD718XX_REG_BUCK2_VOLT_IDLE, 1016 .idle_mask = DVS_BUCK_RUN_MASK, 1017 }, 1018 .init = { 1019 .reg = BD718XX_REG_BUCK2_CTRL, 1020 .mask = BD718XX_BUCK_SEL, 1021 .val = BD718XX_BUCK_SEL, 1022 }, 1023 }, 1024 { 1025 .desc = { 1026 .name = "buck3", 1027 .of_match = of_match_ptr("BUCK3"), 1028 .regulators_node = of_match_ptr("regulators"), 1029 .id = BD718XX_BUCK3, 1030 .type = REGULATOR_VOLTAGE, 1031 .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM, 1032 .linear_ranges = bd718xx_dvs_buck_volts, 1033 .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts), 1034 .vsel_reg = BD71837_REG_BUCK3_VOLT_RUN, 1035 .vsel_mask = DVS_BUCK_RUN_MASK, 1036 .enable_reg = BD71837_REG_BUCK3_CTRL, 1037 .enable_mask = BD718XX_BUCK_EN, 1038 .enable_time = BD71837_BUCK3_STARTUP_TIME, 1039 .ramp_delay_table = bd718xx_ramp_delay, 1040 .n_ramp_values = ARRAY_SIZE(bd718xx_ramp_delay), 1041 .ramp_reg = BD71837_REG_BUCK3_CTRL, 1042 .ramp_mask = BUCK_RAMPRATE_MASK, 1043 .owner = THIS_MODULE, 1044 .of_parse_cb = buck_set_hw_dvs_levels, 1045 }, 1046 .dvs = { 1047 .level_map = ROHM_DVS_LEVEL_RUN, 1048 .run_reg = BD71837_REG_BUCK3_VOLT_RUN, 1049 .run_mask = DVS_BUCK_RUN_MASK, 1050 }, 1051 .init = { 1052 .reg = BD71837_REG_BUCK3_CTRL, 1053 .mask = BD718XX_BUCK_SEL, 1054 .val = BD718XX_BUCK_SEL, 1055 }, 1056 }, 1057 { 1058 .desc = { 1059 .name = "buck4", 1060 .of_match = of_match_ptr("BUCK4"), 1061 .regulators_node = of_match_ptr("regulators"), 1062 .id = BD718XX_BUCK4, 1063 .type = REGULATOR_VOLTAGE, 1064 .n_voltages = BD718XX_DVS_BUCK_VOLTAGE_NUM, 1065 .linear_ranges = bd718xx_dvs_buck_volts, 1066 .n_linear_ranges = ARRAY_SIZE(bd718xx_dvs_buck_volts), 1067 .vsel_reg = BD71837_REG_BUCK4_VOLT_RUN, 1068 .vsel_mask = DVS_BUCK_RUN_MASK, 1069 .enable_reg = BD71837_REG_BUCK4_CTRL, 1070 .enable_mask = BD718XX_BUCK_EN, 1071 .enable_time = BD71837_BUCK4_STARTUP_TIME, 1072 .ramp_delay_table = bd718xx_ramp_delay, 1073 .n_ramp_values = ARRAY_SIZE(bd718xx_ramp_delay), 1074 .ramp_reg = BD71837_REG_BUCK4_CTRL, 1075 .ramp_mask = BUCK_RAMPRATE_MASK, 1076 .owner = THIS_MODULE, 1077 .of_parse_cb = buck_set_hw_dvs_levels, 1078 }, 1079 .dvs = { 1080 .level_map = ROHM_DVS_LEVEL_RUN, 1081 .run_reg = BD71837_REG_BUCK4_VOLT_RUN, 1082 .run_mask = DVS_BUCK_RUN_MASK, 1083 }, 1084 .init = { 1085 .reg = BD71837_REG_BUCK4_CTRL, 1086 .mask = BD718XX_BUCK_SEL, 1087 .val = BD718XX_BUCK_SEL, 1088 }, 1089 }, 1090 { 1091 .desc = { 1092 .name = "buck5", 1093 .of_match = of_match_ptr("BUCK5"), 1094 .regulators_node = of_match_ptr("regulators"), 1095 .id = BD718XX_BUCK5, 1096 .type = REGULATOR_VOLTAGE, 1097 .n_voltages = BD71837_BUCK5_VOLTAGE_NUM, 1098 .linear_ranges = bd71837_buck5_volts, 1099 .n_linear_ranges = 1100 ARRAY_SIZE(bd71837_buck5_volts), 1101 .vsel_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT, 1102 .vsel_mask = BD71837_BUCK5_MASK, 1103 .vsel_range_reg = BD718XX_REG_1ST_NODVS_BUCK_VOLT, 1104 .vsel_range_mask = BD71837_BUCK5_RANGE_MASK, 1105 .linear_range_selectors = bd71837_buck5_volt_range_sel, 1106 .enable_reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL, 1107 .enable_mask = BD718XX_BUCK_EN, 1108 .enable_time = BD71837_BUCK5_STARTUP_TIME, 1109 .owner = THIS_MODULE, 1110 }, 1111 .init = { 1112 .reg = BD718XX_REG_1ST_NODVS_BUCK_CTRL, 1113 .mask = BD718XX_BUCK_SEL, 1114 .val = BD718XX_BUCK_SEL, 1115 }, 1116 }, 1117 { 1118 .desc = { 1119 .name = "buck6", 1120 .of_match = of_match_ptr("BUCK6"), 1121 .regulators_node = of_match_ptr("regulators"), 1122 .id = BD718XX_BUCK6, 1123 .type = REGULATOR_VOLTAGE, 1124 .n_voltages = BD71837_BUCK6_VOLTAGE_NUM, 1125 .linear_ranges = bd71837_buck6_volts, 1126 .n_linear_ranges = 1127 ARRAY_SIZE(bd71837_buck6_volts), 1128 .vsel_reg = BD718XX_REG_2ND_NODVS_BUCK_VOLT, 1129 .vsel_mask = BD71837_BUCK6_MASK, 1130 .enable_reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL, 1131 .enable_mask = BD718XX_BUCK_EN, 1132 .enable_time = BD71837_BUCK6_STARTUP_TIME, 1133 .owner = THIS_MODULE, 1134 }, 1135 .init = { 1136 .reg = BD718XX_REG_2ND_NODVS_BUCK_CTRL, 1137 .mask = BD718XX_BUCK_SEL, 1138 .val = BD718XX_BUCK_SEL, 1139 }, 1140 }, 1141 { 1142 .desc = { 1143 .name = "buck7", 1144 .of_match = of_match_ptr("BUCK7"), 1145 .regulators_node = of_match_ptr("regulators"), 1146 .id = BD718XX_BUCK7, 1147 .type = REGULATOR_VOLTAGE, 1148 .volt_table = &bd718xx_3rd_nodvs_buck_volts[0], 1149 .n_voltages = ARRAY_SIZE(bd718xx_3rd_nodvs_buck_volts), 1150 .vsel_reg = BD718XX_REG_3RD_NODVS_BUCK_VOLT, 1151 .vsel_mask = BD718XX_3RD_NODVS_BUCK_MASK, 1152 .enable_reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL, 1153 .enable_mask = BD718XX_BUCK_EN, 1154 .enable_time = BD71837_BUCK7_STARTUP_TIME, 1155 .owner = THIS_MODULE, 1156 }, 1157 .init = { 1158 .reg = BD718XX_REG_3RD_NODVS_BUCK_CTRL, 1159 .mask = BD718XX_BUCK_SEL, 1160 .val = BD718XX_BUCK_SEL, 1161 }, 1162 }, 1163 { 1164 .desc = { 1165 .name = "buck8", 1166 .of_match = of_match_ptr("BUCK8"), 1167 .regulators_node = of_match_ptr("regulators"), 1168 .id = BD718XX_BUCK8, 1169 .type = REGULATOR_VOLTAGE, 1170 .n_voltages = BD718XX_4TH_NODVS_BUCK_VOLTAGE_NUM, 1171 .linear_ranges = bd718xx_4th_nodvs_buck_volts, 1172 .n_linear_ranges = 1173 ARRAY_SIZE(bd718xx_4th_nodvs_buck_volts), 1174 .vsel_reg = BD718XX_REG_4TH_NODVS_BUCK_VOLT, 1175 .vsel_mask = BD718XX_4TH_NODVS_BUCK_MASK, 1176 .enable_reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL, 1177 .enable_mask = BD718XX_BUCK_EN, 1178 .enable_time = BD71837_BUCK8_STARTUP_TIME, 1179 .owner = THIS_MODULE, 1180 }, 1181 .init = { 1182 .reg = BD718XX_REG_4TH_NODVS_BUCK_CTRL, 1183 .mask = BD718XX_BUCK_SEL, 1184 .val = BD718XX_BUCK_SEL, 1185 }, 1186 }, 1187 { 1188 .desc = { 1189 .name = "ldo1", 1190 .of_match = of_match_ptr("LDO1"), 1191 .regulators_node = of_match_ptr("regulators"), 1192 .id = BD718XX_LDO1, 1193 .type = REGULATOR_VOLTAGE, 1194 .n_voltages = BD718XX_LDO1_VOLTAGE_NUM, 1195 .linear_ranges = bd718xx_ldo1_volts, 1196 .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo1_volts), 1197 .vsel_reg = BD718XX_REG_LDO1_VOLT, 1198 .vsel_mask = BD718XX_LDO1_MASK, 1199 .vsel_range_reg = BD718XX_REG_LDO1_VOLT, 1200 .vsel_range_mask = BD718XX_LDO1_RANGE_MASK, 1201 .linear_range_selectors = bd718xx_ldo1_volt_range_sel, 1202 .enable_reg = BD718XX_REG_LDO1_VOLT, 1203 .enable_mask = BD718XX_LDO_EN, 1204 .enable_time = BD71837_LDO1_STARTUP_TIME, 1205 .owner = THIS_MODULE, 1206 }, 1207 .init = { 1208 .reg = BD718XX_REG_LDO1_VOLT, 1209 .mask = BD718XX_LDO_SEL, 1210 .val = BD718XX_LDO_SEL, 1211 }, 1212 }, 1213 { 1214 .desc = { 1215 .name = "ldo2", 1216 .of_match = of_match_ptr("LDO2"), 1217 .regulators_node = of_match_ptr("regulators"), 1218 .id = BD718XX_LDO2, 1219 .type = REGULATOR_VOLTAGE, 1220 .volt_table = &ldo_2_volts[0], 1221 .vsel_reg = BD718XX_REG_LDO2_VOLT, 1222 .vsel_mask = BD718XX_LDO2_MASK, 1223 .n_voltages = ARRAY_SIZE(ldo_2_volts), 1224 .enable_reg = BD718XX_REG_LDO2_VOLT, 1225 .enable_mask = BD718XX_LDO_EN, 1226 .enable_time = BD71837_LDO2_STARTUP_TIME, 1227 .owner = THIS_MODULE, 1228 }, 1229 .init = { 1230 .reg = BD718XX_REG_LDO2_VOLT, 1231 .mask = BD718XX_LDO_SEL, 1232 .val = BD718XX_LDO_SEL, 1233 }, 1234 }, 1235 { 1236 .desc = { 1237 .name = "ldo3", 1238 .of_match = of_match_ptr("LDO3"), 1239 .regulators_node = of_match_ptr("regulators"), 1240 .id = BD718XX_LDO3, 1241 .type = REGULATOR_VOLTAGE, 1242 .n_voltages = BD718XX_LDO3_VOLTAGE_NUM, 1243 .linear_ranges = bd718xx_ldo3_volts, 1244 .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo3_volts), 1245 .vsel_reg = BD718XX_REG_LDO3_VOLT, 1246 .vsel_mask = BD718XX_LDO3_MASK, 1247 .enable_reg = BD718XX_REG_LDO3_VOLT, 1248 .enable_mask = BD718XX_LDO_EN, 1249 .enable_time = BD71837_LDO3_STARTUP_TIME, 1250 .owner = THIS_MODULE, 1251 }, 1252 .init = { 1253 .reg = BD718XX_REG_LDO3_VOLT, 1254 .mask = BD718XX_LDO_SEL, 1255 .val = BD718XX_LDO_SEL, 1256 }, 1257 }, 1258 { 1259 .desc = { 1260 .name = "ldo4", 1261 .of_match = of_match_ptr("LDO4"), 1262 .regulators_node = of_match_ptr("regulators"), 1263 .id = BD718XX_LDO4, 1264 .type = REGULATOR_VOLTAGE, 1265 .n_voltages = BD718XX_LDO4_VOLTAGE_NUM, 1266 .linear_ranges = bd718xx_ldo4_volts, 1267 .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo4_volts), 1268 .vsel_reg = BD718XX_REG_LDO4_VOLT, 1269 .vsel_mask = BD718XX_LDO4_MASK, 1270 .enable_reg = BD718XX_REG_LDO4_VOLT, 1271 .enable_mask = BD718XX_LDO_EN, 1272 .enable_time = BD71837_LDO4_STARTUP_TIME, 1273 .owner = THIS_MODULE, 1274 }, 1275 .init = { 1276 .reg = BD718XX_REG_LDO4_VOLT, 1277 .mask = BD718XX_LDO_SEL, 1278 .val = BD718XX_LDO_SEL, 1279 }, 1280 }, 1281 { 1282 .desc = { 1283 .name = "ldo5", 1284 .of_match = of_match_ptr("LDO5"), 1285 .regulators_node = of_match_ptr("regulators"), 1286 .id = BD718XX_LDO5, 1287 .type = REGULATOR_VOLTAGE, 1288 .n_voltages = BD71837_LDO5_VOLTAGE_NUM, 1289 .linear_ranges = bd71837_ldo5_volts, 1290 .n_linear_ranges = ARRAY_SIZE(bd71837_ldo5_volts), 1291 /* LDO5 is supplied by buck6 */ 1292 .supply_name = "buck6", 1293 .vsel_reg = BD718XX_REG_LDO5_VOLT, 1294 .vsel_mask = BD71837_LDO5_MASK, 1295 .enable_reg = BD718XX_REG_LDO5_VOLT, 1296 .enable_mask = BD718XX_LDO_EN, 1297 .enable_time = BD71837_LDO5_STARTUP_TIME, 1298 .owner = THIS_MODULE, 1299 }, 1300 .init = { 1301 .reg = BD718XX_REG_LDO5_VOLT, 1302 .mask = BD718XX_LDO_SEL, 1303 .val = BD718XX_LDO_SEL, 1304 }, 1305 .additional_inits = bd71837_ldo5_inits, 1306 .additional_init_amnt = ARRAY_SIZE(bd71837_ldo5_inits), 1307 }, 1308 { 1309 .desc = { 1310 .name = "ldo6", 1311 .of_match = of_match_ptr("LDO6"), 1312 .regulators_node = of_match_ptr("regulators"), 1313 .id = BD718XX_LDO6, 1314 .type = REGULATOR_VOLTAGE, 1315 .n_voltages = BD718XX_LDO6_VOLTAGE_NUM, 1316 .linear_ranges = bd718xx_ldo6_volts, 1317 .n_linear_ranges = ARRAY_SIZE(bd718xx_ldo6_volts), 1318 /* LDO6 is supplied by buck7 */ 1319 .supply_name = "buck7", 1320 .vsel_reg = BD718XX_REG_LDO6_VOLT, 1321 .vsel_mask = BD718XX_LDO6_MASK, 1322 .enable_reg = BD718XX_REG_LDO6_VOLT, 1323 .enable_mask = BD718XX_LDO_EN, 1324 .enable_time = BD71837_LDO6_STARTUP_TIME, 1325 .owner = THIS_MODULE, 1326 }, 1327 .init = { 1328 .reg = BD718XX_REG_LDO6_VOLT, 1329 .mask = BD718XX_LDO_SEL, 1330 .val = BD718XX_LDO_SEL, 1331 }, 1332 .additional_inits = bd71837_ldo6_inits, 1333 .additional_init_amnt = ARRAY_SIZE(bd71837_ldo6_inits), 1334 }, 1335 { 1336 .desc = { 1337 .name = "ldo7", 1338 .of_match = of_match_ptr("LDO7"), 1339 .regulators_node = of_match_ptr("regulators"), 1340 .id = BD718XX_LDO7, 1341 .type = REGULATOR_VOLTAGE, 1342 .n_voltages = BD71837_LDO7_VOLTAGE_NUM, 1343 .linear_ranges = bd71837_ldo7_volts, 1344 .n_linear_ranges = ARRAY_SIZE(bd71837_ldo7_volts), 1345 .vsel_reg = BD71837_REG_LDO7_VOLT, 1346 .vsel_mask = BD71837_LDO7_MASK, 1347 .enable_reg = BD71837_REG_LDO7_VOLT, 1348 .enable_mask = BD718XX_LDO_EN, 1349 .enable_time = BD71837_LDO7_STARTUP_TIME, 1350 .owner = THIS_MODULE, 1351 }, 1352 .init = { 1353 .reg = BD71837_REG_LDO7_VOLT, 1354 .mask = BD718XX_LDO_SEL, 1355 .val = BD718XX_LDO_SEL, 1356 }, 1357 }, 1358 }; 1359 1360 static void mark_hw_controlled(struct device *dev, struct device_node *np, 1361 struct bd718xx_regulator_data *reg_data, 1362 unsigned int num_reg_data, int *info) 1363 { 1364 int i; 1365 1366 for (i = 1; i <= num_reg_data; i++) { 1367 if (!of_node_name_eq(np, reg_data[i-1].desc.of_match)) 1368 continue; 1369 1370 *info |= 1 << (i - 1); 1371 dev_dbg(dev, "regulator %d runlevel controlled\n", i); 1372 return; 1373 } 1374 dev_warn(dev, "Bad regulator node\n"); 1375 } 1376 1377 /* 1378 * Setups where regulator (especially the buck8) output voltage is scaled 1379 * by adding external connection where some other regulator output is connected 1380 * to feedback-pin (over suitable resistors) is getting popular amongst users 1381 * of BD71837. (This allows for example scaling down the buck8 voltages to suit 1382 * lover GPU voltages for projects where buck8 is (ab)used to supply power 1383 * for GPU. Additionally some setups do allow DVS for buck8 but as this do 1384 * produce voltage spikes the HW must be evaluated to be able to survive this 1385 * - hence I keep the DVS disabled for non DVS bucks by default. I don't want 1386 * to help you burn your proto board) 1387 * 1388 * So we allow describing this external connection from DT and scale the 1389 * voltages accordingly. This is what the connection should look like: 1390 * 1391 * |------------| 1392 * | buck 8 |-------+----->Vout 1393 * | | | 1394 * |------------| | 1395 * | FB pin | 1396 * | | 1397 * +-------+--R2---+ 1398 * | 1399 * R1 1400 * | 1401 * V FB-pull-up 1402 * 1403 * Here the buck output is sifted according to formula: 1404 * 1405 * Vout_o = Vo - (Vpu - Vo)*R2/R1 1406 * Linear_step = step_orig*(R1+R2)/R1 1407 * 1408 * where: 1409 * Vout_o is adjusted voltage output at vsel reg value 0 1410 * Vo is original voltage output at vsel reg value 0 1411 * Vpu is the pull-up voltage V FB-pull-up in the picture 1412 * R1 and R2 are resistor values. 1413 * 1414 * As a real world example for buck8 and a specific GPU: 1415 * VLDO = 1.6V (used as FB-pull-up) 1416 * R1 = 1000ohms 1417 * R2 = 150ohms 1418 * VSEL 0x0 => 0.8V – (VLDO – 0.8) * R2 / R1 = 0.68V 1419 * Linear Step = 10mV * (R1 + R2) / R1 = 11.5mV 1420 */ 1421 static int setup_feedback_loop(struct device *dev, struct device_node *np, 1422 struct bd718xx_regulator_data *reg_data, 1423 unsigned int num_reg_data, int fb_uv) 1424 { 1425 int i, r1, r2, ret; 1426 1427 /* 1428 * We do adjust the values in the global desc based on DT settings. 1429 * This may not be best approach as it can cause problems if more than 1430 * one PMIC is controlled from same processor. I don't see such use-case 1431 * for BD718x7 now - so we spare some bits. 1432 * 1433 * If this will point out to be a problem - then we can allocate new 1434 * bd718xx_regulator_data array at probe and just use the global 1435 * array as a template where we copy initial values. Then we can 1436 * use allocated descs for regultor registration and do IC specific 1437 * modifications to this copy while leaving other PMICs untouched. But 1438 * that means allocating new array for each PMIC - and currently I see 1439 * no need for that. 1440 */ 1441 1442 for (i = 0; i < num_reg_data; i++) { 1443 struct regulator_desc *desc = ®_data[i].desc; 1444 int j; 1445 1446 if (!of_node_name_eq(np, desc->of_match)) 1447 continue; 1448 1449 pr_info("Looking at node '%s'\n", desc->of_match); 1450 1451 /* The feedback loop connection does not make sense for LDOs */ 1452 if (desc->id >= BD718XX_LDO1) 1453 return -EINVAL; 1454 1455 ret = of_property_read_u32(np, "rohm,feedback-pull-up-r1-ohms", 1456 &r1); 1457 if (ret) 1458 return ret; 1459 1460 if (!r1) 1461 return -EINVAL; 1462 1463 ret = of_property_read_u32(np, "rohm,feedback-pull-up-r2-ohms", 1464 &r2); 1465 if (ret) 1466 return ret; 1467 1468 if (desc->n_linear_ranges && desc->linear_ranges) { 1469 struct linear_range *new; 1470 1471 new = devm_kzalloc(dev, desc->n_linear_ranges * 1472 sizeof(struct linear_range), 1473 GFP_KERNEL); 1474 if (!new) 1475 return -ENOMEM; 1476 1477 for (j = 0; j < desc->n_linear_ranges; j++) { 1478 int min = desc->linear_ranges[j].min; 1479 int step = desc->linear_ranges[j].step; 1480 1481 min -= (fb_uv - min)*r2/r1; 1482 step = step * (r1 + r2); 1483 step /= r1; 1484 1485 new[j].min = min; 1486 new[j].step = step; 1487 1488 dev_dbg(dev, "%s: old range min %d, step %d\n", 1489 desc->name, desc->linear_ranges[j].min, 1490 desc->linear_ranges[j].step); 1491 dev_dbg(dev, "new range min %d, step %d\n", min, 1492 step); 1493 } 1494 desc->linear_ranges = new; 1495 } 1496 dev_dbg(dev, "regulator '%s' has FB pull-up configured\n", 1497 desc->name); 1498 1499 return 0; 1500 } 1501 1502 return -ENODEV; 1503 } 1504 1505 static int get_special_regulators(struct device *dev, 1506 struct bd718xx_regulator_data *reg_data, 1507 unsigned int num_reg_data, int *info) 1508 { 1509 int ret; 1510 struct device_node *np; 1511 struct device_node *nproot = dev->of_node; 1512 int uv; 1513 1514 *info = 0; 1515 1516 nproot = of_get_child_by_name(nproot, "regulators"); 1517 if (!nproot) { 1518 dev_err(dev, "failed to find regulators node\n"); 1519 return -ENODEV; 1520 } 1521 for_each_child_of_node(nproot, np) { 1522 if (of_property_read_bool(np, "rohm,no-regulator-enable-control")) 1523 mark_hw_controlled(dev, np, reg_data, num_reg_data, 1524 info); 1525 ret = of_property_read_u32(np, "rohm,fb-pull-up-microvolt", 1526 &uv); 1527 if (ret) { 1528 if (ret == -EINVAL) 1529 continue; 1530 else 1531 goto err_out; 1532 } 1533 1534 ret = setup_feedback_loop(dev, np, reg_data, num_reg_data, uv); 1535 if (ret) 1536 goto err_out; 1537 } 1538 1539 of_node_put(nproot); 1540 return 0; 1541 1542 err_out: 1543 of_node_put(np); 1544 of_node_put(nproot); 1545 1546 return ret; 1547 } 1548 1549 static int bd718xx_probe(struct platform_device *pdev) 1550 { 1551 struct regmap *regmap; 1552 struct regulator_config config = { 0 }; 1553 int i, j, err, omit_enable; 1554 bool use_snvs; 1555 struct bd718xx_regulator_data *reg_data; 1556 unsigned int num_reg_data; 1557 enum rohm_chip_type chip = platform_get_device_id(pdev)->driver_data; 1558 const struct regulator_ops **swops, **hwops; 1559 1560 regmap = dev_get_regmap(pdev->dev.parent, NULL); 1561 if (!regmap) { 1562 dev_err(&pdev->dev, "No MFD driver data\n"); 1563 return -EINVAL; 1564 } 1565 1566 switch (chip) { 1567 case ROHM_CHIP_TYPE_BD71837: 1568 reg_data = bd71837_regulators; 1569 num_reg_data = ARRAY_SIZE(bd71837_regulators); 1570 swops = &bd71837_swcontrol_ops[0]; 1571 hwops = &bd71837_hwcontrol_ops[0]; 1572 break; 1573 case ROHM_CHIP_TYPE_BD71847: 1574 reg_data = bd71847_regulators; 1575 num_reg_data = ARRAY_SIZE(bd71847_regulators); 1576 swops = &bd71847_swcontrol_ops[0]; 1577 hwops = &bd71847_hwcontrol_ops[0]; 1578 break; 1579 default: 1580 dev_err(&pdev->dev, "Unsupported chip type\n"); 1581 err = -EINVAL; 1582 goto err; 1583 } 1584 1585 /* Register LOCK release */ 1586 err = regmap_update_bits(regmap, BD718XX_REG_REGLOCK, 1587 (REGLOCK_PWRSEQ | REGLOCK_VREG), 0); 1588 if (err) { 1589 dev_err(&pdev->dev, "Failed to unlock PMIC (%d)\n", err); 1590 goto err; 1591 } else { 1592 dev_dbg(&pdev->dev, "Unlocked lock register 0x%x\n", 1593 BD718XX_REG_REGLOCK); 1594 } 1595 1596 use_snvs = of_property_read_bool(pdev->dev.parent->of_node, 1597 "rohm,reset-snvs-powered"); 1598 1599 /* 1600 * Change the next stage from poweroff to be READY instead of SNVS 1601 * for all reset types because OTP loading at READY will clear SEL 1602 * bit allowing HW defaults for power rails to be used 1603 */ 1604 if (!use_snvs) { 1605 err = regmap_update_bits(regmap, BD718XX_REG_TRANS_COND1, 1606 BD718XX_ON_REQ_POWEROFF_MASK | 1607 BD718XX_SWRESET_POWEROFF_MASK | 1608 BD718XX_WDOG_POWEROFF_MASK | 1609 BD718XX_KEY_L_POWEROFF_MASK, 1610 BD718XX_POWOFF_TO_RDY); 1611 if (err) { 1612 dev_err(&pdev->dev, "Failed to change reset target\n"); 1613 goto err; 1614 } else { 1615 dev_dbg(&pdev->dev, 1616 "Changed all resets from SVNS to READY\n"); 1617 } 1618 } 1619 1620 config.dev = pdev->dev.parent; 1621 config.regmap = regmap; 1622 /* 1623 * There are cases when we want to leave the enable-control for 1624 * the HW state machine and use this driver only for voltage control. 1625 * One special case is when we use PMIC_STBY_REQ line from SoC to PMIC 1626 * in order to set the system to SUSPEND state. 1627 * 1628 * If regulator is taken under SW control the regulator state will not 1629 * be affected by PMIC state machine - Eg. regulator is likely to stay 1630 * on even in SUSPEND 1631 */ 1632 err = get_special_regulators(pdev->dev.parent, reg_data, num_reg_data, 1633 &omit_enable); 1634 if (err) 1635 return err; 1636 1637 for (i = 0; i < num_reg_data; i++) { 1638 1639 struct regulator_desc *desc; 1640 struct regulator_dev *rdev; 1641 struct bd718xx_regulator_data *r; 1642 int no_enable_control = omit_enable & (1 << i); 1643 1644 r = ®_data[i]; 1645 desc = &r->desc; 1646 1647 if (no_enable_control) 1648 desc->ops = hwops[i]; 1649 else 1650 desc->ops = swops[i]; 1651 1652 rdev = devm_regulator_register(&pdev->dev, desc, &config); 1653 if (IS_ERR(rdev)) { 1654 dev_err(&pdev->dev, 1655 "failed to register %s regulator\n", 1656 desc->name); 1657 err = PTR_ERR(rdev); 1658 goto err; 1659 } 1660 1661 /* 1662 * Regulator register gets the regulator constraints and 1663 * applies them (set_machine_constraints). This should have 1664 * turned the control register(s) to correct values and we 1665 * can now switch the control from PMIC state machine to the 1666 * register interface 1667 * 1668 * At poweroff transition PMIC HW disables EN bit for 1669 * regulators but leaves SEL bit untouched. So if state 1670 * transition from POWEROFF is done to SNVS - then all power 1671 * rails controlled by SW (having SEL bit set) stay disabled 1672 * as EN is cleared. This will result boot failure if any 1673 * crucial systems are powered by these rails. We don't 1674 * enable SW control for crucial regulators if snvs state is 1675 * used 1676 */ 1677 if (!no_enable_control && (!use_snvs || 1678 !rdev->constraints->always_on || 1679 !rdev->constraints->boot_on)) { 1680 err = regmap_update_bits(regmap, r->init.reg, 1681 r->init.mask, r->init.val); 1682 if (err) { 1683 dev_err(&pdev->dev, 1684 "Failed to take control for (%s)\n", 1685 desc->name); 1686 goto err; 1687 } 1688 } 1689 for (j = 0; j < r->additional_init_amnt; j++) { 1690 err = regmap_update_bits(regmap, 1691 r->additional_inits[j].reg, 1692 r->additional_inits[j].mask, 1693 r->additional_inits[j].val); 1694 if (err) { 1695 dev_err(&pdev->dev, 1696 "Buck (%s) initialization failed\n", 1697 desc->name); 1698 goto err; 1699 } 1700 } 1701 } 1702 1703 err: 1704 return err; 1705 } 1706 1707 static const struct platform_device_id bd718x7_pmic_id[] = { 1708 { "bd71837-pmic", ROHM_CHIP_TYPE_BD71837 }, 1709 { "bd71847-pmic", ROHM_CHIP_TYPE_BD71847 }, 1710 { }, 1711 }; 1712 MODULE_DEVICE_TABLE(platform, bd718x7_pmic_id); 1713 1714 static struct platform_driver bd718xx_regulator = { 1715 .driver = { 1716 .name = "bd718xx-pmic", 1717 }, 1718 .probe = bd718xx_probe, 1719 .id_table = bd718x7_pmic_id, 1720 }; 1721 1722 module_platform_driver(bd718xx_regulator); 1723 1724 MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>"); 1725 MODULE_DESCRIPTION("BD71837/BD71847 voltage regulator driver"); 1726 MODULE_LICENSE("GPL"); 1727 MODULE_ALIAS("platform:bd718xx-pmic"); 1728