1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright (C) 2016 Linaro Ltd. 4 * 5 * Author: Linus Walleij <linus.walleij@linaro.org> 6 */ 7 8 #include <linux/bitops.h> 9 #include <linux/delay.h> 10 #include <linux/err.h> 11 #include <linux/mfd/stmpe.h> 12 #include <linux/module.h> 13 #include <linux/of.h> 14 #include <linux/platform_device.h> 15 #include <linux/pwm.h> 16 #include <linux/slab.h> 17 18 #define STMPE24XX_PWMCS 0x30 19 #define PWMCS_EN_PWM0 BIT(0) 20 #define PWMCS_EN_PWM1 BIT(1) 21 #define PWMCS_EN_PWM2 BIT(2) 22 #define STMPE24XX_PWMIC0 0x38 23 #define STMPE24XX_PWMIC1 0x39 24 #define STMPE24XX_PWMIC2 0x3a 25 26 #define STMPE_PWM_24XX_PINBASE 21 27 28 struct stmpe_pwm { 29 struct stmpe *stmpe; 30 struct pwm_chip chip; 31 u8 last_duty; 32 }; 33 34 static inline struct stmpe_pwm *to_stmpe_pwm(struct pwm_chip *chip) 35 { 36 return container_of(chip, struct stmpe_pwm, chip); 37 } 38 39 static int stmpe_24xx_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm) 40 { 41 struct stmpe_pwm *stmpe_pwm = to_stmpe_pwm(chip); 42 u8 value; 43 int ret; 44 45 ret = stmpe_reg_read(stmpe_pwm->stmpe, STMPE24XX_PWMCS); 46 if (ret < 0) { 47 dev_err(chip->dev, "error reading PWM#%u control\n", 48 pwm->hwpwm); 49 return ret; 50 } 51 52 value = ret | BIT(pwm->hwpwm); 53 54 ret = stmpe_reg_write(stmpe_pwm->stmpe, STMPE24XX_PWMCS, value); 55 if (ret) { 56 dev_err(chip->dev, "error writing PWM#%u control\n", 57 pwm->hwpwm); 58 return ret; 59 } 60 61 return 0; 62 } 63 64 static int stmpe_24xx_pwm_disable(struct pwm_chip *chip, 65 struct pwm_device *pwm) 66 { 67 struct stmpe_pwm *stmpe_pwm = to_stmpe_pwm(chip); 68 u8 value; 69 int ret; 70 71 ret = stmpe_reg_read(stmpe_pwm->stmpe, STMPE24XX_PWMCS); 72 if (ret < 0) { 73 dev_err(chip->dev, "error reading PWM#%u control\n", 74 pwm->hwpwm); 75 return ret; 76 } 77 78 value = ret & ~BIT(pwm->hwpwm); 79 80 ret = stmpe_reg_write(stmpe_pwm->stmpe, STMPE24XX_PWMCS, value); 81 if (ret) 82 dev_err(chip->dev, "error writing PWM#%u control\n", 83 pwm->hwpwm); 84 return ret; 85 } 86 87 /* STMPE 24xx PWM instructions */ 88 #define SMAX 0x007f 89 #define SMIN 0x00ff 90 #define GTS 0x0000 91 #define LOAD BIT(14) /* Only available on 2403 */ 92 #define RAMPUP 0x0000 93 #define RAMPDOWN BIT(7) 94 #define PRESCALE_512 BIT(14) 95 #define STEPTIME_1 BIT(8) 96 #define BRANCH (BIT(15) | BIT(13)) 97 98 static int stmpe_24xx_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm, 99 int duty_ns, int period_ns) 100 { 101 struct stmpe_pwm *stmpe_pwm = to_stmpe_pwm(chip); 102 unsigned int i, pin; 103 u16 program[3] = { 104 SMAX, 105 GTS, 106 GTS, 107 }; 108 u8 offset; 109 int ret; 110 111 /* Make sure we are disabled */ 112 if (pwm_is_enabled(pwm)) { 113 ret = stmpe_24xx_pwm_disable(chip, pwm); 114 if (ret) 115 return ret; 116 } else { 117 /* Connect the PWM to the pin */ 118 pin = pwm->hwpwm; 119 120 /* On STMPE2401 and 2403 pins 21,22,23 are used */ 121 if (stmpe_pwm->stmpe->partnum == STMPE2401 || 122 stmpe_pwm->stmpe->partnum == STMPE2403) 123 pin += STMPE_PWM_24XX_PINBASE; 124 125 ret = stmpe_set_altfunc(stmpe_pwm->stmpe, BIT(pin), 126 STMPE_BLOCK_PWM); 127 if (ret) { 128 dev_err(chip->dev, "unable to connect PWM#%u to pin\n", 129 pwm->hwpwm); 130 return ret; 131 } 132 } 133 134 /* STMPE24XX */ 135 switch (pwm->hwpwm) { 136 case 0: 137 offset = STMPE24XX_PWMIC0; 138 break; 139 140 case 1: 141 offset = STMPE24XX_PWMIC1; 142 break; 143 144 case 2: 145 offset = STMPE24XX_PWMIC2; 146 break; 147 148 default: 149 /* Should not happen as npwm is 3 */ 150 return -ENODEV; 151 } 152 153 dev_dbg(chip->dev, "PWM#%u: config duty %d ns, period %d ns\n", 154 pwm->hwpwm, duty_ns, period_ns); 155 156 if (duty_ns == 0) { 157 if (stmpe_pwm->stmpe->partnum == STMPE2401) 158 program[0] = SMAX; /* off all the time */ 159 160 if (stmpe_pwm->stmpe->partnum == STMPE2403) 161 program[0] = LOAD | 0xff; /* LOAD 0xff */ 162 163 stmpe_pwm->last_duty = 0x00; 164 } else if (duty_ns == period_ns) { 165 if (stmpe_pwm->stmpe->partnum == STMPE2401) 166 program[0] = SMIN; /* on all the time */ 167 168 if (stmpe_pwm->stmpe->partnum == STMPE2403) 169 program[0] = LOAD | 0x00; /* LOAD 0x00 */ 170 171 stmpe_pwm->last_duty = 0xff; 172 } else { 173 u8 value, last = stmpe_pwm->last_duty; 174 unsigned long duty; 175 176 /* 177 * Counter goes from 0x00 to 0xff repeatedly at 32768 Hz, 178 * (means a period of 30517 ns) then this is compared to the 179 * counter from the ramp, if this is >= PWM counter the output 180 * is high. With LOAD we can define how much of the cycle it 181 * is on. 182 * 183 * Prescale = 0 -> 2 kHz -> T = 1/f = 488281.25 ns 184 */ 185 186 /* Scale to 0..0xff */ 187 duty = duty_ns * 256; 188 duty = DIV_ROUND_CLOSEST(duty, period_ns); 189 value = duty; 190 191 if (value == last) { 192 /* Run the old program */ 193 if (pwm_is_enabled(pwm)) 194 stmpe_24xx_pwm_enable(chip, pwm); 195 196 return 0; 197 } else if (stmpe_pwm->stmpe->partnum == STMPE2403) { 198 /* STMPE2403 can simply set the right PWM value */ 199 program[0] = LOAD | value; 200 program[1] = 0x0000; 201 } else if (stmpe_pwm->stmpe->partnum == STMPE2401) { 202 /* STMPE2401 need a complex program */ 203 u16 incdec = 0x0000; 204 205 if (last < value) 206 /* Count up */ 207 incdec = RAMPUP | (value - last); 208 else 209 /* Count down */ 210 incdec = RAMPDOWN | (last - value); 211 212 /* Step to desired value, smoothly */ 213 program[0] = PRESCALE_512 | STEPTIME_1 | incdec; 214 215 /* Loop eternally to 0x00 */ 216 program[1] = BRANCH; 217 } 218 219 dev_dbg(chip->dev, 220 "PWM#%u: value = %02x, last_duty = %02x, program=%04x,%04x,%04x\n", 221 pwm->hwpwm, value, last, program[0], program[1], 222 program[2]); 223 stmpe_pwm->last_duty = value; 224 } 225 226 /* 227 * We can write programs of up to 64 16-bit words into this channel. 228 */ 229 for (i = 0; i < ARRAY_SIZE(program); i++) { 230 u8 value; 231 232 value = (program[i] >> 8) & 0xff; 233 234 ret = stmpe_reg_write(stmpe_pwm->stmpe, offset, value); 235 if (ret) { 236 dev_err(chip->dev, "error writing register %02x: %d\n", 237 offset, ret); 238 return ret; 239 } 240 241 value = program[i] & 0xff; 242 243 ret = stmpe_reg_write(stmpe_pwm->stmpe, offset, value); 244 if (ret) { 245 dev_err(chip->dev, "error writing register %02x: %d\n", 246 offset, ret); 247 return ret; 248 } 249 } 250 251 /* If we were enabled, re-enable this PWM */ 252 if (pwm_is_enabled(pwm)) 253 stmpe_24xx_pwm_enable(chip, pwm); 254 255 /* Sleep for 200ms so we're sure it will take effect */ 256 msleep(200); 257 258 dev_dbg(chip->dev, "programmed PWM#%u, %u bytes\n", pwm->hwpwm, i); 259 260 return 0; 261 } 262 263 static int stmpe_24xx_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, 264 const struct pwm_state *state) 265 { 266 int err; 267 268 if (state->polarity != PWM_POLARITY_NORMAL) 269 return -EINVAL; 270 271 if (!state->enabled) { 272 if (pwm->state.enabled) 273 return stmpe_24xx_pwm_disable(chip, pwm); 274 275 return 0; 276 } 277 278 err = stmpe_24xx_pwm_config(pwm->chip, pwm, state->duty_cycle, state->period); 279 if (err) 280 return err; 281 282 if (!pwm->state.enabled) 283 err = stmpe_24xx_pwm_enable(chip, pwm); 284 285 return err; 286 } 287 288 static const struct pwm_ops stmpe_24xx_pwm_ops = { 289 .apply = stmpe_24xx_pwm_apply, 290 .owner = THIS_MODULE, 291 }; 292 293 static int __init stmpe_pwm_probe(struct platform_device *pdev) 294 { 295 struct stmpe *stmpe = dev_get_drvdata(pdev->dev.parent); 296 struct stmpe_pwm *stmpe_pwm; 297 int ret; 298 299 stmpe_pwm = devm_kzalloc(&pdev->dev, sizeof(*stmpe_pwm), GFP_KERNEL); 300 if (!stmpe_pwm) 301 return -ENOMEM; 302 303 stmpe_pwm->stmpe = stmpe; 304 stmpe_pwm->chip.dev = &pdev->dev; 305 306 if (stmpe->partnum == STMPE2401 || stmpe->partnum == STMPE2403) { 307 stmpe_pwm->chip.ops = &stmpe_24xx_pwm_ops; 308 stmpe_pwm->chip.npwm = 3; 309 } else { 310 if (stmpe->partnum == STMPE1601) 311 dev_err(&pdev->dev, "STMPE1601 not yet supported\n"); 312 else 313 dev_err(&pdev->dev, "Unknown STMPE PWM\n"); 314 315 return -ENODEV; 316 } 317 318 ret = stmpe_enable(stmpe, STMPE_BLOCK_PWM); 319 if (ret) 320 return ret; 321 322 ret = pwmchip_add(&stmpe_pwm->chip); 323 if (ret) { 324 stmpe_disable(stmpe, STMPE_BLOCK_PWM); 325 return ret; 326 } 327 328 return 0; 329 } 330 331 static struct platform_driver stmpe_pwm_driver = { 332 .driver = { 333 .name = "stmpe-pwm", 334 }, 335 }; 336 builtin_platform_driver_probe(stmpe_pwm_driver, stmpe_pwm_probe); 337