1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * PWM device driver for ST SoCs
4 *
5 * Copyright (C) 2013-2016 STMicroelectronics (R&D) Limited
6 *
7 * Author: Ajit Pal Singh <ajitpal.singh@st.com>
8 * Lee Jones <lee.jones@linaro.org>
9 */
10
11 #include <linux/clk.h>
12 #include <linux/interrupt.h>
13 #include <linux/math64.h>
14 #include <linux/mfd/syscon.h>
15 #include <linux/module.h>
16 #include <linux/of.h>
17 #include <linux/platform_device.h>
18 #include <linux/pwm.h>
19 #include <linux/regmap.h>
20 #include <linux/sched.h>
21 #include <linux/slab.h>
22 #include <linux/time.h>
23 #include <linux/wait.h>
24
25 #define PWM_OUT_VAL(x) (0x00 + (4 * (x))) /* Device's Duty Cycle register */
26 #define PWM_CPT_VAL(x) (0x10 + (4 * (x))) /* Capture value */
27 #define PWM_CPT_EDGE(x) (0x30 + (4 * (x))) /* Edge to capture on */
28
29 #define STI_PWM_CTRL 0x50 /* Control/Config register */
30 #define STI_INT_EN 0x54 /* Interrupt Enable/Disable register */
31 #define STI_INT_STA 0x58 /* Interrupt Status register */
32 #define PWM_INT_ACK 0x5c
33 #define PWM_PRESCALE_LOW_MASK 0x0f
34 #define PWM_PRESCALE_HIGH_MASK 0xf0
35 #define PWM_CPT_EDGE_MASK 0x03
36 #define PWM_INT_ACK_MASK 0x1ff
37
38 #define STI_MAX_CPT_DEVS 4
39 #define CPT_DC_MAX 0xff
40
41 /* Regfield IDs */
42 enum {
43 /* Bits in PWM_CTRL*/
44 PWMCLK_PRESCALE_LOW,
45 PWMCLK_PRESCALE_HIGH,
46 CPTCLK_PRESCALE,
47
48 PWM_OUT_EN,
49 PWM_CPT_EN,
50
51 PWM_CPT_INT_EN,
52 PWM_CPT_INT_STAT,
53
54 /* Keep last */
55 MAX_REGFIELDS
56 };
57
58 /*
59 * Each capture input can be programmed to detect rising-edge, falling-edge,
60 * either edge or neither egde.
61 */
62 enum sti_cpt_edge {
63 CPT_EDGE_DISABLED,
64 CPT_EDGE_RISING,
65 CPT_EDGE_FALLING,
66 CPT_EDGE_BOTH,
67 };
68
69 struct sti_cpt_ddata {
70 u32 snapshot[3];
71 unsigned int index;
72 struct mutex lock;
73 wait_queue_head_t wait;
74 };
75
76 struct sti_pwm_compat_data {
77 const struct reg_field *reg_fields;
78 unsigned int pwm_num_devs;
79 unsigned int cpt_num_devs;
80 unsigned int max_pwm_cnt;
81 unsigned int max_prescale;
82 struct sti_cpt_ddata *ddata;
83 };
84
85 struct sti_pwm_chip {
86 struct device *dev;
87 struct clk *pwm_clk;
88 struct clk *cpt_clk;
89 struct regmap *regmap;
90 struct sti_pwm_compat_data *cdata;
91 struct regmap_field *prescale_low;
92 struct regmap_field *prescale_high;
93 struct regmap_field *pwm_out_en;
94 struct regmap_field *pwm_cpt_en;
95 struct regmap_field *pwm_cpt_int_en;
96 struct regmap_field *pwm_cpt_int_stat;
97 struct pwm_chip chip;
98 struct pwm_device *cur;
99 unsigned long configured;
100 unsigned int en_count;
101 struct mutex sti_pwm_lock; /* To sync between enable/disable calls */
102 void __iomem *mmio;
103 };
104
105 static const struct reg_field sti_pwm_regfields[MAX_REGFIELDS] = {
106 [PWMCLK_PRESCALE_LOW] = REG_FIELD(STI_PWM_CTRL, 0, 3),
107 [PWMCLK_PRESCALE_HIGH] = REG_FIELD(STI_PWM_CTRL, 11, 14),
108 [CPTCLK_PRESCALE] = REG_FIELD(STI_PWM_CTRL, 4, 8),
109 [PWM_OUT_EN] = REG_FIELD(STI_PWM_CTRL, 9, 9),
110 [PWM_CPT_EN] = REG_FIELD(STI_PWM_CTRL, 10, 10),
111 [PWM_CPT_INT_EN] = REG_FIELD(STI_INT_EN, 1, 4),
112 [PWM_CPT_INT_STAT] = REG_FIELD(STI_INT_STA, 1, 4),
113 };
114
to_sti_pwmchip(struct pwm_chip * chip)115 static inline struct sti_pwm_chip *to_sti_pwmchip(struct pwm_chip *chip)
116 {
117 return container_of(chip, struct sti_pwm_chip, chip);
118 }
119
120 /*
121 * Calculate the prescaler value corresponding to the period.
122 */
sti_pwm_get_prescale(struct sti_pwm_chip * pc,unsigned long period,unsigned int * prescale)123 static int sti_pwm_get_prescale(struct sti_pwm_chip *pc, unsigned long period,
124 unsigned int *prescale)
125 {
126 struct sti_pwm_compat_data *cdata = pc->cdata;
127 unsigned long clk_rate;
128 unsigned long value;
129 unsigned int ps;
130
131 clk_rate = clk_get_rate(pc->pwm_clk);
132 if (!clk_rate) {
133 dev_err(pc->dev, "failed to get clock rate\n");
134 return -EINVAL;
135 }
136
137 /*
138 * prescale = ((period_ns * clk_rate) / (10^9 * (max_pwm_cnt + 1)) - 1
139 */
140 value = NSEC_PER_SEC / clk_rate;
141 value *= cdata->max_pwm_cnt + 1;
142
143 if (period % value)
144 return -EINVAL;
145
146 ps = period / value - 1;
147 if (ps > cdata->max_prescale)
148 return -EINVAL;
149
150 *prescale = ps;
151
152 return 0;
153 }
154
155 /*
156 * For STiH4xx PWM IP, the PWM period is fixed to 256 local clock cycles. The
157 * only way to change the period (apart from changing the PWM input clock) is
158 * to change the PWM clock prescaler.
159 *
160 * The prescaler is of 8 bits, so 256 prescaler values and hence 256 possible
161 * period values are supported (for a particular clock rate). The requested
162 * period will be applied only if it matches one of these 256 values.
163 */
sti_pwm_config(struct pwm_chip * chip,struct pwm_device * pwm,int duty_ns,int period_ns)164 static int sti_pwm_config(struct pwm_chip *chip, struct pwm_device *pwm,
165 int duty_ns, int period_ns)
166 {
167 struct sti_pwm_chip *pc = to_sti_pwmchip(chip);
168 struct sti_pwm_compat_data *cdata = pc->cdata;
169 unsigned int ncfg, value, prescale = 0;
170 struct pwm_device *cur = pc->cur;
171 struct device *dev = pc->dev;
172 bool period_same = false;
173 int ret;
174
175 ncfg = hweight_long(pc->configured);
176 if (ncfg)
177 period_same = (period_ns == pwm_get_period(cur));
178
179 /*
180 * Allow configuration changes if one of the following conditions
181 * satisfy.
182 * 1. No devices have been configured.
183 * 2. Only one device has been configured and the new request is for
184 * the same device.
185 * 3. Only one device has been configured and the new request is for
186 * a new device and period of the new device is same as the current
187 * configured period.
188 * 4. More than one devices are configured and period of the new
189 * requestis the same as the current period.
190 */
191 if (!ncfg ||
192 ((ncfg == 1) && (pwm->hwpwm == cur->hwpwm)) ||
193 ((ncfg == 1) && (pwm->hwpwm != cur->hwpwm) && period_same) ||
194 ((ncfg > 1) && period_same)) {
195 /* Enable clock before writing to PWM registers. */
196 ret = clk_enable(pc->pwm_clk);
197 if (ret)
198 return ret;
199
200 ret = clk_enable(pc->cpt_clk);
201 if (ret)
202 return ret;
203
204 if (!period_same) {
205 ret = sti_pwm_get_prescale(pc, period_ns, &prescale);
206 if (ret)
207 goto clk_dis;
208
209 value = prescale & PWM_PRESCALE_LOW_MASK;
210
211 ret = regmap_field_write(pc->prescale_low, value);
212 if (ret)
213 goto clk_dis;
214
215 value = (prescale & PWM_PRESCALE_HIGH_MASK) >> 4;
216
217 ret = regmap_field_write(pc->prescale_high, value);
218 if (ret)
219 goto clk_dis;
220 }
221
222 /*
223 * When PWMVal == 0, PWM pulse = 1 local clock cycle.
224 * When PWMVal == max_pwm_count,
225 * PWM pulse = (max_pwm_count + 1) local cycles,
226 * that is continuous pulse: signal never goes low.
227 */
228 value = cdata->max_pwm_cnt * duty_ns / period_ns;
229
230 ret = regmap_write(pc->regmap, PWM_OUT_VAL(pwm->hwpwm), value);
231 if (ret)
232 goto clk_dis;
233
234 ret = regmap_field_write(pc->pwm_cpt_int_en, 0);
235
236 set_bit(pwm->hwpwm, &pc->configured);
237 pc->cur = pwm;
238
239 dev_dbg(dev, "prescale:%u, period:%i, duty:%i, value:%u\n",
240 prescale, period_ns, duty_ns, value);
241 } else {
242 return -EINVAL;
243 }
244
245 clk_dis:
246 clk_disable(pc->pwm_clk);
247 clk_disable(pc->cpt_clk);
248 return ret;
249 }
250
sti_pwm_enable(struct pwm_chip * chip,struct pwm_device * pwm)251 static int sti_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
252 {
253 struct sti_pwm_chip *pc = to_sti_pwmchip(chip);
254 struct device *dev = pc->dev;
255 int ret = 0;
256
257 /*
258 * Since we have a common enable for all PWM devices, do not enable if
259 * already enabled.
260 */
261 mutex_lock(&pc->sti_pwm_lock);
262
263 if (!pc->en_count) {
264 ret = clk_enable(pc->pwm_clk);
265 if (ret)
266 goto out;
267
268 ret = clk_enable(pc->cpt_clk);
269 if (ret)
270 goto out;
271
272 ret = regmap_field_write(pc->pwm_out_en, 1);
273 if (ret) {
274 dev_err(dev, "failed to enable PWM device %u: %d\n",
275 pwm->hwpwm, ret);
276 goto out;
277 }
278 }
279
280 pc->en_count++;
281
282 out:
283 mutex_unlock(&pc->sti_pwm_lock);
284 return ret;
285 }
286
sti_pwm_disable(struct pwm_chip * chip,struct pwm_device * pwm)287 static void sti_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
288 {
289 struct sti_pwm_chip *pc = to_sti_pwmchip(chip);
290
291 mutex_lock(&pc->sti_pwm_lock);
292
293 if (--pc->en_count) {
294 mutex_unlock(&pc->sti_pwm_lock);
295 return;
296 }
297
298 regmap_field_write(pc->pwm_out_en, 0);
299
300 clk_disable(pc->pwm_clk);
301 clk_disable(pc->cpt_clk);
302
303 mutex_unlock(&pc->sti_pwm_lock);
304 }
305
sti_pwm_free(struct pwm_chip * chip,struct pwm_device * pwm)306 static void sti_pwm_free(struct pwm_chip *chip, struct pwm_device *pwm)
307 {
308 struct sti_pwm_chip *pc = to_sti_pwmchip(chip);
309
310 clear_bit(pwm->hwpwm, &pc->configured);
311 }
312
sti_pwm_capture(struct pwm_chip * chip,struct pwm_device * pwm,struct pwm_capture * result,unsigned long timeout)313 static int sti_pwm_capture(struct pwm_chip *chip, struct pwm_device *pwm,
314 struct pwm_capture *result, unsigned long timeout)
315 {
316 struct sti_pwm_chip *pc = to_sti_pwmchip(chip);
317 struct sti_pwm_compat_data *cdata = pc->cdata;
318 struct sti_cpt_ddata *ddata = &cdata->ddata[pwm->hwpwm];
319 struct device *dev = pc->dev;
320 unsigned int effective_ticks;
321 unsigned long long high, low;
322 int ret;
323
324 if (pwm->hwpwm >= cdata->cpt_num_devs) {
325 dev_err(dev, "device %u is not valid\n", pwm->hwpwm);
326 return -EINVAL;
327 }
328
329 mutex_lock(&ddata->lock);
330 ddata->index = 0;
331
332 /* Prepare capture measurement */
333 regmap_write(pc->regmap, PWM_CPT_EDGE(pwm->hwpwm), CPT_EDGE_RISING);
334 regmap_field_write(pc->pwm_cpt_int_en, BIT(pwm->hwpwm));
335
336 /* Enable capture */
337 ret = regmap_field_write(pc->pwm_cpt_en, 1);
338 if (ret) {
339 dev_err(dev, "failed to enable PWM capture %u: %d\n",
340 pwm->hwpwm, ret);
341 goto out;
342 }
343
344 ret = wait_event_interruptible_timeout(ddata->wait, ddata->index > 1,
345 msecs_to_jiffies(timeout));
346
347 regmap_write(pc->regmap, PWM_CPT_EDGE(pwm->hwpwm), CPT_EDGE_DISABLED);
348
349 if (ret == -ERESTARTSYS)
350 goto out;
351
352 switch (ddata->index) {
353 case 0:
354 case 1:
355 /*
356 * Getting here could mean:
357 * - input signal is constant of less than 1 Hz
358 * - there is no input signal at all
359 *
360 * In such case the frequency is rounded down to 0
361 */
362 result->period = 0;
363 result->duty_cycle = 0;
364
365 break;
366
367 case 2:
368 /* We have everying we need */
369 high = ddata->snapshot[1] - ddata->snapshot[0];
370 low = ddata->snapshot[2] - ddata->snapshot[1];
371
372 effective_ticks = clk_get_rate(pc->cpt_clk);
373
374 result->period = (high + low) * NSEC_PER_SEC;
375 result->period /= effective_ticks;
376
377 result->duty_cycle = high * NSEC_PER_SEC;
378 result->duty_cycle /= effective_ticks;
379
380 break;
381
382 default:
383 dev_err(dev, "internal error\n");
384 break;
385 }
386
387 out:
388 /* Disable capture */
389 regmap_field_write(pc->pwm_cpt_en, 0);
390
391 mutex_unlock(&ddata->lock);
392 return ret;
393 }
394
sti_pwm_apply(struct pwm_chip * chip,struct pwm_device * pwm,const struct pwm_state * state)395 static int sti_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
396 const struct pwm_state *state)
397 {
398 struct sti_pwm_chip *pc = to_sti_pwmchip(chip);
399 struct sti_pwm_compat_data *cdata = pc->cdata;
400 struct device *dev = pc->dev;
401 int err;
402
403 if (pwm->hwpwm >= cdata->pwm_num_devs) {
404 dev_err(dev, "device %u is not valid for pwm mode\n",
405 pwm->hwpwm);
406 return -EINVAL;
407 }
408
409 if (state->polarity != PWM_POLARITY_NORMAL)
410 return -EINVAL;
411
412 if (!state->enabled) {
413 if (pwm->state.enabled)
414 sti_pwm_disable(chip, pwm);
415
416 return 0;
417 }
418
419 err = sti_pwm_config(pwm->chip, pwm, state->duty_cycle, state->period);
420 if (err)
421 return err;
422
423 if (!pwm->state.enabled)
424 err = sti_pwm_enable(chip, pwm);
425
426 return err;
427 }
428
429 static const struct pwm_ops sti_pwm_ops = {
430 .capture = sti_pwm_capture,
431 .apply = sti_pwm_apply,
432 .free = sti_pwm_free,
433 .owner = THIS_MODULE,
434 };
435
sti_pwm_interrupt(int irq,void * data)436 static irqreturn_t sti_pwm_interrupt(int irq, void *data)
437 {
438 struct sti_pwm_chip *pc = data;
439 struct device *dev = pc->dev;
440 struct sti_cpt_ddata *ddata;
441 int devicenum;
442 unsigned int cpt_int_stat;
443 unsigned int reg;
444 int ret = IRQ_NONE;
445
446 ret = regmap_field_read(pc->pwm_cpt_int_stat, &cpt_int_stat);
447 if (ret)
448 return ret;
449
450 while (cpt_int_stat) {
451 devicenum = ffs(cpt_int_stat) - 1;
452
453 ddata = &pc->cdata->ddata[devicenum];
454
455 /*
456 * Capture input:
457 * _______ _______
458 * | | | |
459 * __| |_________________| |________
460 * ^0 ^1 ^2
461 *
462 * Capture start by the first available rising edge. When a
463 * capture event occurs, capture value (CPT_VALx) is stored,
464 * index incremented, capture edge changed.
465 *
466 * After the capture, if the index > 1, we have collected the
467 * necessary data so we signal the thread waiting for it and
468 * disable the capture by setting capture edge to none
469 */
470
471 regmap_read(pc->regmap,
472 PWM_CPT_VAL(devicenum),
473 &ddata->snapshot[ddata->index]);
474
475 switch (ddata->index) {
476 case 0:
477 case 1:
478 regmap_read(pc->regmap, PWM_CPT_EDGE(devicenum), ®);
479 reg ^= PWM_CPT_EDGE_MASK;
480 regmap_write(pc->regmap, PWM_CPT_EDGE(devicenum), reg);
481
482 ddata->index++;
483 break;
484
485 case 2:
486 regmap_write(pc->regmap,
487 PWM_CPT_EDGE(devicenum),
488 CPT_EDGE_DISABLED);
489 wake_up(&ddata->wait);
490 break;
491
492 default:
493 dev_err(dev, "Internal error\n");
494 }
495
496 cpt_int_stat &= ~BIT_MASK(devicenum);
497
498 ret = IRQ_HANDLED;
499 }
500
501 /* Just ACK everything */
502 regmap_write(pc->regmap, PWM_INT_ACK, PWM_INT_ACK_MASK);
503
504 return ret;
505 }
506
sti_pwm_probe_dt(struct sti_pwm_chip * pc)507 static int sti_pwm_probe_dt(struct sti_pwm_chip *pc)
508 {
509 struct device *dev = pc->dev;
510 const struct reg_field *reg_fields;
511 struct device_node *np = dev->of_node;
512 struct sti_pwm_compat_data *cdata = pc->cdata;
513 u32 num_devs;
514 int ret;
515
516 ret = of_property_read_u32(np, "st,pwm-num-chan", &num_devs);
517 if (!ret)
518 cdata->pwm_num_devs = num_devs;
519
520 ret = of_property_read_u32(np, "st,capture-num-chan", &num_devs);
521 if (!ret)
522 cdata->cpt_num_devs = num_devs;
523
524 if (!cdata->pwm_num_devs && !cdata->cpt_num_devs) {
525 dev_err(dev, "No channels configured\n");
526 return -EINVAL;
527 }
528
529 reg_fields = cdata->reg_fields;
530
531 pc->prescale_low = devm_regmap_field_alloc(dev, pc->regmap,
532 reg_fields[PWMCLK_PRESCALE_LOW]);
533 if (IS_ERR(pc->prescale_low))
534 return PTR_ERR(pc->prescale_low);
535
536 pc->prescale_high = devm_regmap_field_alloc(dev, pc->regmap,
537 reg_fields[PWMCLK_PRESCALE_HIGH]);
538 if (IS_ERR(pc->prescale_high))
539 return PTR_ERR(pc->prescale_high);
540
541 pc->pwm_out_en = devm_regmap_field_alloc(dev, pc->regmap,
542 reg_fields[PWM_OUT_EN]);
543 if (IS_ERR(pc->pwm_out_en))
544 return PTR_ERR(pc->pwm_out_en);
545
546 pc->pwm_cpt_en = devm_regmap_field_alloc(dev, pc->regmap,
547 reg_fields[PWM_CPT_EN]);
548 if (IS_ERR(pc->pwm_cpt_en))
549 return PTR_ERR(pc->pwm_cpt_en);
550
551 pc->pwm_cpt_int_en = devm_regmap_field_alloc(dev, pc->regmap,
552 reg_fields[PWM_CPT_INT_EN]);
553 if (IS_ERR(pc->pwm_cpt_int_en))
554 return PTR_ERR(pc->pwm_cpt_int_en);
555
556 pc->pwm_cpt_int_stat = devm_regmap_field_alloc(dev, pc->regmap,
557 reg_fields[PWM_CPT_INT_STAT]);
558 if (PTR_ERR_OR_ZERO(pc->pwm_cpt_int_stat))
559 return PTR_ERR(pc->pwm_cpt_int_stat);
560
561 return 0;
562 }
563
564 static const struct regmap_config sti_pwm_regmap_config = {
565 .reg_bits = 32,
566 .val_bits = 32,
567 .reg_stride = 4,
568 };
569
sti_pwm_probe(struct platform_device * pdev)570 static int sti_pwm_probe(struct platform_device *pdev)
571 {
572 struct device *dev = &pdev->dev;
573 struct sti_pwm_compat_data *cdata;
574 struct pwm_chip *chip;
575 struct sti_pwm_chip *pc;
576 unsigned int i;
577 int irq, ret;
578
579 pc = devm_kzalloc(dev, sizeof(*pc), GFP_KERNEL);
580 if (!pc)
581 return -ENOMEM;
582 chip = &pc->chip;
583
584 cdata = devm_kzalloc(dev, sizeof(*cdata), GFP_KERNEL);
585 if (!cdata)
586 return -ENOMEM;
587
588 pc->mmio = devm_platform_ioremap_resource(pdev, 0);
589 if (IS_ERR(pc->mmio))
590 return PTR_ERR(pc->mmio);
591
592 pc->regmap = devm_regmap_init_mmio(dev, pc->mmio,
593 &sti_pwm_regmap_config);
594 if (IS_ERR(pc->regmap))
595 return PTR_ERR(pc->regmap);
596
597 irq = platform_get_irq(pdev, 0);
598 if (irq < 0)
599 return irq;
600
601 ret = devm_request_irq(&pdev->dev, irq, sti_pwm_interrupt, 0,
602 pdev->name, pc);
603 if (ret < 0) {
604 dev_err(&pdev->dev, "Failed to request IRQ\n");
605 return ret;
606 }
607
608 /*
609 * Setup PWM data with default values: some values could be replaced
610 * with specific ones provided from Device Tree.
611 */
612 cdata->reg_fields = sti_pwm_regfields;
613 cdata->max_prescale = 0xff;
614 cdata->max_pwm_cnt = 255;
615 cdata->pwm_num_devs = 0;
616 cdata->cpt_num_devs = 0;
617
618 pc->cdata = cdata;
619 pc->dev = dev;
620 pc->en_count = 0;
621 mutex_init(&pc->sti_pwm_lock);
622
623 ret = sti_pwm_probe_dt(pc);
624 if (ret)
625 return ret;
626
627 if (cdata->pwm_num_devs) {
628 pc->pwm_clk = devm_clk_get_prepared(dev, "pwm");
629 if (IS_ERR(pc->pwm_clk)) {
630 dev_err(dev, "failed to get PWM clock\n");
631 return PTR_ERR(pc->pwm_clk);
632 }
633 }
634
635 if (cdata->cpt_num_devs) {
636 pc->cpt_clk = devm_clk_get_prepared(dev, "capture");
637 if (IS_ERR(pc->cpt_clk)) {
638 dev_err(dev, "failed to get PWM capture clock\n");
639 return PTR_ERR(pc->cpt_clk);
640 }
641
642 cdata->ddata = devm_kzalloc(dev, cdata->cpt_num_devs * sizeof(*cdata->ddata), GFP_KERNEL);
643 if (!cdata->ddata)
644 return -ENOMEM;
645 }
646
647 chip->dev = dev;
648 chip->ops = &sti_pwm_ops;
649 chip->npwm = max(cdata->pwm_num_devs, cdata->cpt_num_devs);
650
651 for (i = 0; i < cdata->cpt_num_devs; i++) {
652 struct sti_cpt_ddata *ddata = &cdata->ddata[i];
653
654 init_waitqueue_head(&ddata->wait);
655 mutex_init(&ddata->lock);
656 }
657
658 return devm_pwmchip_add(dev, chip);
659 }
660
661 static const struct of_device_id sti_pwm_of_match[] = {
662 { .compatible = "st,sti-pwm", },
663 { /* sentinel */ }
664 };
665 MODULE_DEVICE_TABLE(of, sti_pwm_of_match);
666
667 static struct platform_driver sti_pwm_driver = {
668 .driver = {
669 .name = "sti-pwm",
670 .of_match_table = sti_pwm_of_match,
671 },
672 .probe = sti_pwm_probe,
673 };
674 module_platform_driver(sti_pwm_driver);
675
676 MODULE_AUTHOR("Ajit Pal Singh <ajitpal.singh@st.com>");
677 MODULE_DESCRIPTION("STMicroelectronics ST PWM driver");
678 MODULE_LICENSE("GPL");
679