1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Driver for Atmel Pulse Width Modulation Controller 4 * 5 * Copyright (C) 2013 Atmel Corporation 6 * Bo Shen <voice.shen@atmel.com> 7 * 8 * Links to reference manuals for the supported PWM chips can be found in 9 * Documentation/arch/arm/microchip.rst. 10 * 11 * Limitations: 12 * - Periods start with the inactive level. 13 * - Hardware has to be stopped in general to update settings. 14 * 15 * Software bugs/possible improvements: 16 * - When atmel_pwm_apply() is called with state->enabled=false a change in 17 * state->polarity isn't honored. 18 * - Instead of sleeping to wait for a completed period, the interrupt 19 * functionality could be used. 20 */ 21 22 #include <linux/clk.h> 23 #include <linux/delay.h> 24 #include <linux/err.h> 25 #include <linux/io.h> 26 #include <linux/module.h> 27 #include <linux/of.h> 28 #include <linux/of_device.h> 29 #include <linux/platform_device.h> 30 #include <linux/pwm.h> 31 #include <linux/slab.h> 32 33 /* The following is global registers for PWM controller */ 34 #define PWM_ENA 0x04 35 #define PWM_DIS 0x08 36 #define PWM_SR 0x0C 37 #define PWM_ISR 0x1C 38 /* Bit field in SR */ 39 #define PWM_SR_ALL_CH_ON 0x0F 40 41 /* The following register is PWM channel related registers */ 42 #define PWM_CH_REG_OFFSET 0x200 43 #define PWM_CH_REG_SIZE 0x20 44 45 #define PWM_CMR 0x0 46 /* Bit field in CMR */ 47 #define PWM_CMR_CPOL (1 << 9) 48 #define PWM_CMR_UPD_CDTY (1 << 10) 49 #define PWM_CMR_CPRE_MSK 0xF 50 51 /* The following registers for PWM v1 */ 52 #define PWMV1_CDTY 0x04 53 #define PWMV1_CPRD 0x08 54 #define PWMV1_CUPD 0x10 55 56 /* The following registers for PWM v2 */ 57 #define PWMV2_CDTY 0x04 58 #define PWMV2_CDTYUPD 0x08 59 #define PWMV2_CPRD 0x0C 60 #define PWMV2_CPRDUPD 0x10 61 62 #define PWM_MAX_PRES 10 63 64 struct atmel_pwm_registers { 65 u8 period; 66 u8 period_upd; 67 u8 duty; 68 u8 duty_upd; 69 }; 70 71 struct atmel_pwm_config { 72 u32 period_bits; 73 }; 74 75 struct atmel_pwm_data { 76 struct atmel_pwm_registers regs; 77 struct atmel_pwm_config cfg; 78 }; 79 80 struct atmel_pwm_chip { 81 struct pwm_chip chip; 82 struct clk *clk; 83 void __iomem *base; 84 const struct atmel_pwm_data *data; 85 86 /* 87 * The hardware supports a mechanism to update a channel's duty cycle at 88 * the end of the currently running period. When such an update is 89 * pending we delay disabling the PWM until the new configuration is 90 * active because otherwise pmw_config(duty_cycle=0); pwm_disable(); 91 * might not result in an inactive output. 92 * This bitmask tracks for which channels an update is pending in 93 * hardware. 94 */ 95 u32 update_pending; 96 97 /* Protects .update_pending */ 98 spinlock_t lock; 99 }; 100 101 static inline struct atmel_pwm_chip *to_atmel_pwm_chip(struct pwm_chip *chip) 102 { 103 return container_of(chip, struct atmel_pwm_chip, chip); 104 } 105 106 static inline u32 atmel_pwm_readl(struct atmel_pwm_chip *chip, 107 unsigned long offset) 108 { 109 return readl_relaxed(chip->base + offset); 110 } 111 112 static inline void atmel_pwm_writel(struct atmel_pwm_chip *chip, 113 unsigned long offset, unsigned long val) 114 { 115 writel_relaxed(val, chip->base + offset); 116 } 117 118 static inline u32 atmel_pwm_ch_readl(struct atmel_pwm_chip *chip, 119 unsigned int ch, unsigned long offset) 120 { 121 unsigned long base = PWM_CH_REG_OFFSET + ch * PWM_CH_REG_SIZE; 122 123 return atmel_pwm_readl(chip, base + offset); 124 } 125 126 static inline void atmel_pwm_ch_writel(struct atmel_pwm_chip *chip, 127 unsigned int ch, unsigned long offset, 128 unsigned long val) 129 { 130 unsigned long base = PWM_CH_REG_OFFSET + ch * PWM_CH_REG_SIZE; 131 132 atmel_pwm_writel(chip, base + offset, val); 133 } 134 135 static void atmel_pwm_update_pending(struct atmel_pwm_chip *chip) 136 { 137 /* 138 * Each channel that has its bit in ISR set started a new period since 139 * ISR was cleared and so there is no more update pending. Note that 140 * reading ISR clears it, so this needs to handle all channels to not 141 * loose information. 142 */ 143 u32 isr = atmel_pwm_readl(chip, PWM_ISR); 144 145 chip->update_pending &= ~isr; 146 } 147 148 static void atmel_pwm_set_pending(struct atmel_pwm_chip *chip, unsigned int ch) 149 { 150 spin_lock(&chip->lock); 151 152 /* 153 * Clear pending flags in hardware because otherwise there might still 154 * be a stale flag in ISR. 155 */ 156 atmel_pwm_update_pending(chip); 157 158 chip->update_pending |= (1 << ch); 159 160 spin_unlock(&chip->lock); 161 } 162 163 static int atmel_pwm_test_pending(struct atmel_pwm_chip *chip, unsigned int ch) 164 { 165 int ret = 0; 166 167 spin_lock(&chip->lock); 168 169 if (chip->update_pending & (1 << ch)) { 170 atmel_pwm_update_pending(chip); 171 172 if (chip->update_pending & (1 << ch)) 173 ret = 1; 174 } 175 176 spin_unlock(&chip->lock); 177 178 return ret; 179 } 180 181 static int atmel_pwm_wait_nonpending(struct atmel_pwm_chip *chip, unsigned int ch) 182 { 183 unsigned long timeout = jiffies + 2 * HZ; 184 int ret; 185 186 while ((ret = atmel_pwm_test_pending(chip, ch)) && 187 time_before(jiffies, timeout)) 188 usleep_range(10, 100); 189 190 return ret ? -ETIMEDOUT : 0; 191 } 192 193 static int atmel_pwm_calculate_cprd_and_pres(struct pwm_chip *chip, 194 unsigned long clkrate, 195 const struct pwm_state *state, 196 unsigned long *cprd, u32 *pres) 197 { 198 struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip); 199 unsigned long long cycles = state->period; 200 int shift; 201 202 /* Calculate the period cycles and prescale value */ 203 cycles *= clkrate; 204 do_div(cycles, NSEC_PER_SEC); 205 206 /* 207 * The register for the period length is cfg.period_bits bits wide. 208 * So for each bit the number of clock cycles is wider divide the input 209 * clock frequency by two using pres and shift cprd accordingly. 210 */ 211 shift = fls(cycles) - atmel_pwm->data->cfg.period_bits; 212 213 if (shift > PWM_MAX_PRES) { 214 dev_err(chip->dev, "pres exceeds the maximum value\n"); 215 return -EINVAL; 216 } else if (shift > 0) { 217 *pres = shift; 218 cycles >>= *pres; 219 } else { 220 *pres = 0; 221 } 222 223 *cprd = cycles; 224 225 return 0; 226 } 227 228 static void atmel_pwm_calculate_cdty(const struct pwm_state *state, 229 unsigned long clkrate, unsigned long cprd, 230 u32 pres, unsigned long *cdty) 231 { 232 unsigned long long cycles = state->duty_cycle; 233 234 cycles *= clkrate; 235 do_div(cycles, NSEC_PER_SEC); 236 cycles >>= pres; 237 *cdty = cprd - cycles; 238 } 239 240 static void atmel_pwm_update_cdty(struct pwm_chip *chip, struct pwm_device *pwm, 241 unsigned long cdty) 242 { 243 struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip); 244 u32 val; 245 246 if (atmel_pwm->data->regs.duty_upd == 247 atmel_pwm->data->regs.period_upd) { 248 val = atmel_pwm_ch_readl(atmel_pwm, pwm->hwpwm, PWM_CMR); 249 val &= ~PWM_CMR_UPD_CDTY; 250 atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWM_CMR, val); 251 } 252 253 atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, 254 atmel_pwm->data->regs.duty_upd, cdty); 255 atmel_pwm_set_pending(atmel_pwm, pwm->hwpwm); 256 } 257 258 static void atmel_pwm_set_cprd_cdty(struct pwm_chip *chip, 259 struct pwm_device *pwm, 260 unsigned long cprd, unsigned long cdty) 261 { 262 struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip); 263 264 atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, 265 atmel_pwm->data->regs.duty, cdty); 266 atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, 267 atmel_pwm->data->regs.period, cprd); 268 } 269 270 static void atmel_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm, 271 bool disable_clk) 272 { 273 struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip); 274 unsigned long timeout; 275 276 atmel_pwm_wait_nonpending(atmel_pwm, pwm->hwpwm); 277 278 atmel_pwm_writel(atmel_pwm, PWM_DIS, 1 << pwm->hwpwm); 279 280 /* 281 * Wait for the PWM channel disable operation to be effective before 282 * stopping the clock. 283 */ 284 timeout = jiffies + 2 * HZ; 285 286 while ((atmel_pwm_readl(atmel_pwm, PWM_SR) & (1 << pwm->hwpwm)) && 287 time_before(jiffies, timeout)) 288 usleep_range(10, 100); 289 290 if (disable_clk) 291 clk_disable(atmel_pwm->clk); 292 } 293 294 static int atmel_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm, 295 const struct pwm_state *state) 296 { 297 struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip); 298 struct pwm_state cstate; 299 unsigned long cprd, cdty; 300 u32 pres, val; 301 int ret; 302 303 pwm_get_state(pwm, &cstate); 304 305 if (state->enabled) { 306 unsigned long clkrate = clk_get_rate(atmel_pwm->clk); 307 308 if (cstate.enabled && 309 cstate.polarity == state->polarity && 310 cstate.period == state->period) { 311 u32 cmr = atmel_pwm_ch_readl(atmel_pwm, pwm->hwpwm, PWM_CMR); 312 313 cprd = atmel_pwm_ch_readl(atmel_pwm, pwm->hwpwm, 314 atmel_pwm->data->regs.period); 315 pres = cmr & PWM_CMR_CPRE_MSK; 316 317 atmel_pwm_calculate_cdty(state, clkrate, cprd, pres, &cdty); 318 atmel_pwm_update_cdty(chip, pwm, cdty); 319 return 0; 320 } 321 322 ret = atmel_pwm_calculate_cprd_and_pres(chip, clkrate, state, &cprd, 323 &pres); 324 if (ret) { 325 dev_err(chip->dev, 326 "failed to calculate cprd and prescaler\n"); 327 return ret; 328 } 329 330 atmel_pwm_calculate_cdty(state, clkrate, cprd, pres, &cdty); 331 332 if (cstate.enabled) { 333 atmel_pwm_disable(chip, pwm, false); 334 } else { 335 ret = clk_enable(atmel_pwm->clk); 336 if (ret) { 337 dev_err(chip->dev, "failed to enable clock\n"); 338 return ret; 339 } 340 } 341 342 /* It is necessary to preserve CPOL, inside CMR */ 343 val = atmel_pwm_ch_readl(atmel_pwm, pwm->hwpwm, PWM_CMR); 344 val = (val & ~PWM_CMR_CPRE_MSK) | (pres & PWM_CMR_CPRE_MSK); 345 if (state->polarity == PWM_POLARITY_NORMAL) 346 val &= ~PWM_CMR_CPOL; 347 else 348 val |= PWM_CMR_CPOL; 349 atmel_pwm_ch_writel(atmel_pwm, pwm->hwpwm, PWM_CMR, val); 350 atmel_pwm_set_cprd_cdty(chip, pwm, cprd, cdty); 351 atmel_pwm_writel(atmel_pwm, PWM_ENA, 1 << pwm->hwpwm); 352 } else if (cstate.enabled) { 353 atmel_pwm_disable(chip, pwm, true); 354 } 355 356 return 0; 357 } 358 359 static int atmel_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm, 360 struct pwm_state *state) 361 { 362 struct atmel_pwm_chip *atmel_pwm = to_atmel_pwm_chip(chip); 363 u32 sr, cmr; 364 365 sr = atmel_pwm_readl(atmel_pwm, PWM_SR); 366 cmr = atmel_pwm_ch_readl(atmel_pwm, pwm->hwpwm, PWM_CMR); 367 368 if (sr & (1 << pwm->hwpwm)) { 369 unsigned long rate = clk_get_rate(atmel_pwm->clk); 370 u32 cdty, cprd, pres; 371 u64 tmp; 372 373 pres = cmr & PWM_CMR_CPRE_MSK; 374 375 cprd = atmel_pwm_ch_readl(atmel_pwm, pwm->hwpwm, 376 atmel_pwm->data->regs.period); 377 tmp = (u64)cprd * NSEC_PER_SEC; 378 tmp <<= pres; 379 state->period = DIV64_U64_ROUND_UP(tmp, rate); 380 381 /* Wait for an updated duty_cycle queued in hardware */ 382 atmel_pwm_wait_nonpending(atmel_pwm, pwm->hwpwm); 383 384 cdty = atmel_pwm_ch_readl(atmel_pwm, pwm->hwpwm, 385 atmel_pwm->data->regs.duty); 386 tmp = (u64)(cprd - cdty) * NSEC_PER_SEC; 387 tmp <<= pres; 388 state->duty_cycle = DIV64_U64_ROUND_UP(tmp, rate); 389 390 state->enabled = true; 391 } else { 392 state->enabled = false; 393 } 394 395 if (cmr & PWM_CMR_CPOL) 396 state->polarity = PWM_POLARITY_INVERSED; 397 else 398 state->polarity = PWM_POLARITY_NORMAL; 399 400 return 0; 401 } 402 403 static const struct pwm_ops atmel_pwm_ops = { 404 .apply = atmel_pwm_apply, 405 .get_state = atmel_pwm_get_state, 406 .owner = THIS_MODULE, 407 }; 408 409 static const struct atmel_pwm_data atmel_sam9rl_pwm_data = { 410 .regs = { 411 .period = PWMV1_CPRD, 412 .period_upd = PWMV1_CUPD, 413 .duty = PWMV1_CDTY, 414 .duty_upd = PWMV1_CUPD, 415 }, 416 .cfg = { 417 /* 16 bits to keep period and duty. */ 418 .period_bits = 16, 419 }, 420 }; 421 422 static const struct atmel_pwm_data atmel_sama5_pwm_data = { 423 .regs = { 424 .period = PWMV2_CPRD, 425 .period_upd = PWMV2_CPRDUPD, 426 .duty = PWMV2_CDTY, 427 .duty_upd = PWMV2_CDTYUPD, 428 }, 429 .cfg = { 430 /* 16 bits to keep period and duty. */ 431 .period_bits = 16, 432 }, 433 }; 434 435 static const struct atmel_pwm_data mchp_sam9x60_pwm_data = { 436 .regs = { 437 .period = PWMV1_CPRD, 438 .period_upd = PWMV1_CUPD, 439 .duty = PWMV1_CDTY, 440 .duty_upd = PWMV1_CUPD, 441 }, 442 .cfg = { 443 /* 32 bits to keep period and duty. */ 444 .period_bits = 32, 445 }, 446 }; 447 448 static const struct of_device_id atmel_pwm_dt_ids[] = { 449 { 450 .compatible = "atmel,at91sam9rl-pwm", 451 .data = &atmel_sam9rl_pwm_data, 452 }, { 453 .compatible = "atmel,sama5d3-pwm", 454 .data = &atmel_sama5_pwm_data, 455 }, { 456 .compatible = "atmel,sama5d2-pwm", 457 .data = &atmel_sama5_pwm_data, 458 }, { 459 .compatible = "microchip,sam9x60-pwm", 460 .data = &mchp_sam9x60_pwm_data, 461 }, { 462 /* sentinel */ 463 }, 464 }; 465 MODULE_DEVICE_TABLE(of, atmel_pwm_dt_ids); 466 467 static int atmel_pwm_probe(struct platform_device *pdev) 468 { 469 struct atmel_pwm_chip *atmel_pwm; 470 int ret; 471 472 atmel_pwm = devm_kzalloc(&pdev->dev, sizeof(*atmel_pwm), GFP_KERNEL); 473 if (!atmel_pwm) 474 return -ENOMEM; 475 476 atmel_pwm->data = of_device_get_match_data(&pdev->dev); 477 478 atmel_pwm->update_pending = 0; 479 spin_lock_init(&atmel_pwm->lock); 480 481 atmel_pwm->base = devm_platform_ioremap_resource(pdev, 0); 482 if (IS_ERR(atmel_pwm->base)) 483 return PTR_ERR(atmel_pwm->base); 484 485 atmel_pwm->clk = devm_clk_get(&pdev->dev, NULL); 486 if (IS_ERR(atmel_pwm->clk)) 487 return PTR_ERR(atmel_pwm->clk); 488 489 ret = clk_prepare(atmel_pwm->clk); 490 if (ret) { 491 dev_err(&pdev->dev, "failed to prepare PWM clock\n"); 492 return ret; 493 } 494 495 atmel_pwm->chip.dev = &pdev->dev; 496 atmel_pwm->chip.ops = &atmel_pwm_ops; 497 atmel_pwm->chip.npwm = 4; 498 499 ret = pwmchip_add(&atmel_pwm->chip); 500 if (ret < 0) { 501 dev_err(&pdev->dev, "failed to add PWM chip %d\n", ret); 502 goto unprepare_clk; 503 } 504 505 platform_set_drvdata(pdev, atmel_pwm); 506 507 return ret; 508 509 unprepare_clk: 510 clk_unprepare(atmel_pwm->clk); 511 return ret; 512 } 513 514 static void atmel_pwm_remove(struct platform_device *pdev) 515 { 516 struct atmel_pwm_chip *atmel_pwm = platform_get_drvdata(pdev); 517 518 pwmchip_remove(&atmel_pwm->chip); 519 520 clk_unprepare(atmel_pwm->clk); 521 } 522 523 static struct platform_driver atmel_pwm_driver = { 524 .driver = { 525 .name = "atmel-pwm", 526 .of_match_table = of_match_ptr(atmel_pwm_dt_ids), 527 }, 528 .probe = atmel_pwm_probe, 529 .remove_new = atmel_pwm_remove, 530 }; 531 module_platform_driver(atmel_pwm_driver); 532 533 MODULE_ALIAS("platform:atmel-pwm"); 534 MODULE_AUTHOR("Bo Shen <voice.shen@atmel.com>"); 535 MODULE_DESCRIPTION("Atmel PWM driver"); 536 MODULE_LICENSE("GPL v2"); 537