1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Charger Driver for Rockchip rk817 4 * 5 * Copyright (c) 2021 Maya Matuszczyk <maccraft123mc@gmail.com> 6 * 7 * Authors: Maya Matuszczyk <maccraft123mc@gmail.com> 8 * Chris Morgan <macromorgan@hotmail.com> 9 */ 10 11 #include <asm/unaligned.h> 12 #include <linux/devm-helpers.h> 13 #include <linux/mfd/rk808.h> 14 #include <linux/irq.h> 15 #include <linux/of.h> 16 #include <linux/platform_device.h> 17 #include <linux/power_supply.h> 18 #include <linux/regmap.h> 19 20 /* Charging statuses reported by hardware register */ 21 enum rk817_charge_status { 22 CHRG_OFF, 23 DEAD_CHRG, 24 TRICKLE_CHRG, 25 CC_OR_CV_CHRG, 26 CHARGE_FINISH, 27 USB_OVER_VOL, 28 BAT_TMP_ERR, 29 BAT_TIM_ERR, 30 }; 31 32 /* 33 * Max charging current read to/written from hardware register. 34 * Note how highest value corresponding to 0x7 is the lowest 35 * current, this is per the datasheet. 36 */ 37 enum rk817_chg_cur { 38 CHG_1A, 39 CHG_1_5A, 40 CHG_2A, 41 CHG_2_5A, 42 CHG_2_75A, 43 CHG_3A, 44 CHG_3_5A, 45 CHG_0_5A, 46 }; 47 48 struct rk817_charger { 49 struct device *dev; 50 struct rk808 *rk808; 51 52 struct power_supply *bat_ps; 53 struct power_supply *chg_ps; 54 bool plugged_in; 55 bool battery_present; 56 57 /* 58 * voltage_k and voltage_b values are used to calibrate the ADC 59 * voltage readings. While they are documented in the BSP kernel and 60 * datasheet as voltage_k and voltage_b, there is no further 61 * information explaining them in more detail. 62 */ 63 64 uint32_t voltage_k; 65 uint32_t voltage_b; 66 67 /* 68 * soc - state of charge - like the BSP this is stored as a percentage, 69 * to the thousandth. BSP has a display state of charge (dsoc) and a 70 * remaining state of charge (rsoc). This value will be used for both 71 * purposes here so we don't do any fancy math to try and "smooth" the 72 * charge and just report it as it is. Note for example an soc of 100 73 * is stored as 100000, an soc of 50 is stored as 50000, etc. 74 */ 75 int soc; 76 77 /* 78 * Capacity of battery when fully charged, equal or less than design 79 * capacity depending upon wear. BSP kernel saves to nvram in mAh, 80 * so this value is in mAh not the standard uAh. 81 */ 82 int fcc_mah; 83 84 /* 85 * Calibrate the SOC on a fully charged battery, this way we can use 86 * the calibrated SOC value to correct for columb counter drift. 87 */ 88 bool soc_cal; 89 90 /* Implementation specific immutable properties from device tree */ 91 int res_div; 92 int sleep_enter_current_ua; 93 int sleep_filter_current_ua; 94 int bat_charge_full_design_uah; 95 int bat_voltage_min_design_uv; 96 int bat_voltage_max_design_uv; 97 98 /* Values updated periodically by driver for display. */ 99 int charge_now_uah; 100 int volt_avg_uv; 101 int cur_avg_ua; 102 int max_chg_cur_ua; 103 int max_chg_volt_uv; 104 int charge_status; 105 int charger_input_volt_avg_uv; 106 107 /* Work queue to periodically update values. */ 108 struct delayed_work work; 109 }; 110 111 /* ADC coefficients extracted from BSP kernel */ 112 #define ADC_TO_CURRENT(adc_value, res_div) \ 113 (adc_value * 172 / res_div) 114 115 #define CURRENT_TO_ADC(current, samp_res) \ 116 (current * samp_res / 172) 117 118 #define CHARGE_TO_ADC(capacity, res_div) \ 119 (capacity * res_div * 3600 / 172 * 1000) 120 121 #define ADC_TO_CHARGE_UAH(adc_value, res_div) \ 122 (adc_value / 3600 * 172 / res_div) 123 124 static int rk817_chg_cur_to_reg(u32 chg_cur_ma) 125 { 126 if (chg_cur_ma >= 3500) 127 return CHG_3_5A; 128 else if (chg_cur_ma >= 3000) 129 return CHG_3A; 130 else if (chg_cur_ma >= 2750) 131 return CHG_2_75A; 132 else if (chg_cur_ma >= 2500) 133 return CHG_2_5A; 134 else if (chg_cur_ma >= 2000) 135 return CHG_2A; 136 else if (chg_cur_ma >= 1500) 137 return CHG_1_5A; 138 else if (chg_cur_ma >= 1000) 139 return CHG_1A; 140 else if (chg_cur_ma >= 500) 141 return CHG_0_5A; 142 else 143 return -EINVAL; 144 } 145 146 static int rk817_chg_cur_from_reg(u8 reg) 147 { 148 switch (reg) { 149 case CHG_0_5A: 150 return 500000; 151 case CHG_1A: 152 return 1000000; 153 case CHG_1_5A: 154 return 1500000; 155 case CHG_2A: 156 return 2000000; 157 case CHG_2_5A: 158 return 2500000; 159 case CHG_2_75A: 160 return 2750000; 161 case CHG_3A: 162 return 3000000; 163 case CHG_3_5A: 164 return 3500000; 165 default: 166 return -EINVAL; 167 } 168 } 169 170 static void rk817_bat_calib_vol(struct rk817_charger *charger) 171 { 172 uint32_t vcalib0 = 0; 173 uint32_t vcalib1 = 0; 174 u8 bulk_reg[2]; 175 176 /* calibrate voltage */ 177 regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_VCALIB0_H, 178 bulk_reg, 2); 179 vcalib0 = get_unaligned_be16(bulk_reg); 180 181 regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_VCALIB1_H, 182 bulk_reg, 2); 183 vcalib1 = get_unaligned_be16(bulk_reg); 184 185 /* values were taken from BSP kernel */ 186 charger->voltage_k = (4025 - 2300) * 1000 / 187 ((vcalib1 - vcalib0) ? (vcalib1 - vcalib0) : 1); 188 charger->voltage_b = 4025 - (charger->voltage_k * vcalib1) / 1000; 189 } 190 191 static void rk817_bat_calib_cur(struct rk817_charger *charger) 192 { 193 u8 bulk_reg[2]; 194 195 /* calibrate current */ 196 regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_IOFFSET_H, 197 bulk_reg, 2); 198 regmap_bulk_write(charger->rk808->regmap, RK817_GAS_GAUGE_CAL_OFFSET_H, 199 bulk_reg, 2); 200 } 201 202 /* 203 * note that only the fcc_mah is really used by this driver, the other values 204 * are to ensure we can remain backwards compatible with the BSP kernel. 205 */ 206 static int rk817_record_battery_nvram_values(struct rk817_charger *charger) 207 { 208 u8 bulk_reg[3]; 209 int ret, rsoc; 210 211 /* 212 * write the soc value to the nvram location used by the BSP kernel 213 * for the dsoc value. 214 */ 215 put_unaligned_le24(charger->soc, bulk_reg); 216 ret = regmap_bulk_write(charger->rk808->regmap, RK817_GAS_GAUGE_BAT_R1, 217 bulk_reg, 3); 218 if (ret < 0) 219 return ret; 220 /* 221 * write the remaining capacity in mah to the nvram location used by 222 * the BSP kernel for the rsoc value. 223 */ 224 rsoc = (charger->soc * charger->fcc_mah) / 100000; 225 put_unaligned_le24(rsoc, bulk_reg); 226 ret = regmap_bulk_write(charger->rk808->regmap, RK817_GAS_GAUGE_DATA0, 227 bulk_reg, 3); 228 if (ret < 0) 229 return ret; 230 /* write the fcc_mah in mAh, just as the BSP kernel does. */ 231 put_unaligned_le24(charger->fcc_mah, bulk_reg); 232 ret = regmap_bulk_write(charger->rk808->regmap, RK817_GAS_GAUGE_DATA3, 233 bulk_reg, 3); 234 if (ret < 0) 235 return ret; 236 237 return 0; 238 } 239 240 static int rk817_bat_calib_cap(struct rk817_charger *charger) 241 { 242 struct rk808 *rk808 = charger->rk808; 243 int tmp, charge_now, charge_now_adc, volt_avg; 244 u8 bulk_reg[4]; 245 246 /* Calibrate the soc and fcc on a fully charged battery */ 247 248 if (charger->charge_status == CHARGE_FINISH && (!charger->soc_cal)) { 249 /* 250 * soc should be 100000 and columb counter should show the full 251 * charge capacity. Note that if the device is unplugged for a 252 * period of several days the columb counter will have a large 253 * margin of error, so setting it back to the full charge on 254 * a completed charge cycle should correct this (my device was 255 * showing 33% battery after 3 days unplugged when it should 256 * have been closer to 95% based on voltage and charge 257 * current). 258 */ 259 260 charger->soc = 100000; 261 charge_now_adc = CHARGE_TO_ADC(charger->fcc_mah, 262 charger->res_div); 263 put_unaligned_be32(charge_now_adc, bulk_reg); 264 regmap_bulk_write(rk808->regmap, RK817_GAS_GAUGE_Q_INIT_H3, 265 bulk_reg, 4); 266 267 charger->soc_cal = 1; 268 dev_dbg(charger->dev, 269 "Fully charged. SOC is %d, full capacity is %d\n", 270 charger->soc, charger->fcc_mah * 1000); 271 } 272 273 /* 274 * The columb counter can drift up slightly, so we should correct for 275 * it. But don't correct it until we're at 100% soc. 276 */ 277 if (charger->charge_status == CHARGE_FINISH && charger->soc_cal) { 278 regmap_bulk_read(rk808->regmap, RK817_GAS_GAUGE_Q_PRES_H3, 279 bulk_reg, 4); 280 charge_now_adc = get_unaligned_be32(bulk_reg); 281 if (charge_now_adc < 0) 282 return charge_now_adc; 283 charge_now = ADC_TO_CHARGE_UAH(charge_now_adc, 284 charger->res_div); 285 286 /* 287 * Re-init columb counter with updated values to correct drift. 288 */ 289 if (charge_now / 1000 > charger->fcc_mah) { 290 dev_dbg(charger->dev, 291 "Recalibrating columb counter to %d uah\n", 292 charge_now); 293 /* 294 * Order of operations matters here to ensure we keep 295 * enough precision until the last step to keep from 296 * making needless updates to columb counter. 297 */ 298 charge_now_adc = CHARGE_TO_ADC(charger->fcc_mah, 299 charger->res_div); 300 put_unaligned_be32(charge_now_adc, bulk_reg); 301 regmap_bulk_write(rk808->regmap, 302 RK817_GAS_GAUGE_Q_INIT_H3, 303 bulk_reg, 4); 304 } 305 } 306 307 /* 308 * Calibrate the fully charged capacity when we previously had a full 309 * battery (soc_cal = 1) and are now empty (at or below minimum design 310 * voltage). If our columb counter is still positive, subtract that 311 * from our fcc value to get a calibrated fcc, and if our columb 312 * counter is negative add that to our fcc (but not to exceed our 313 * design capacity). 314 */ 315 regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_BAT_VOL_H, 316 bulk_reg, 2); 317 tmp = get_unaligned_be16(bulk_reg); 318 volt_avg = (charger->voltage_k * tmp) + 1000 * charger->voltage_b; 319 if (volt_avg <= charger->bat_voltage_min_design_uv && 320 charger->soc_cal) { 321 regmap_bulk_read(rk808->regmap, RK817_GAS_GAUGE_Q_PRES_H3, 322 bulk_reg, 4); 323 charge_now_adc = get_unaligned_be32(bulk_reg); 324 charge_now = ADC_TO_CHARGE_UAH(charge_now_adc, 325 charger->res_div); 326 /* 327 * Note, if charge_now is negative this will add it (what we 328 * want) and if it's positive this will subtract (also what 329 * we want). 330 */ 331 charger->fcc_mah = charger->fcc_mah - (charge_now / 1000); 332 333 dev_dbg(charger->dev, 334 "Recalibrating full charge capacity to %d uah\n", 335 charger->fcc_mah * 1000); 336 } 337 338 /* 339 * Set the SOC to 0 if we are below the minimum system voltage. 340 */ 341 if (volt_avg <= charger->bat_voltage_min_design_uv) { 342 charger->soc = 0; 343 charge_now_adc = CHARGE_TO_ADC(0, charger->res_div); 344 put_unaligned_be32(charge_now_adc, bulk_reg); 345 regmap_bulk_write(rk808->regmap, 346 RK817_GAS_GAUGE_Q_INIT_H3, bulk_reg, 4); 347 dev_warn(charger->dev, 348 "Battery voltage %d below minimum voltage %d\n", 349 volt_avg, charger->bat_voltage_min_design_uv); 350 } 351 352 rk817_record_battery_nvram_values(charger); 353 354 return 0; 355 } 356 357 static void rk817_read_props(struct rk817_charger *charger) 358 { 359 int tmp, reg; 360 u8 bulk_reg[4]; 361 362 /* 363 * Recalibrate voltage and current readings if we need to BSP does both 364 * on CUR_CALIB_UPD, ignoring VOL_CALIB_UPD. Curiously enough, both 365 * documentation and the BSP show that you perform an update if bit 7 366 * is 1, but you clear the status by writing a 1 to bit 7. 367 */ 368 regmap_read(charger->rk808->regmap, RK817_GAS_GAUGE_ADC_CONFIG1, ®); 369 if (reg & RK817_VOL_CUR_CALIB_UPD) { 370 rk817_bat_calib_cur(charger); 371 rk817_bat_calib_vol(charger); 372 regmap_write_bits(charger->rk808->regmap, 373 RK817_GAS_GAUGE_ADC_CONFIG1, 374 RK817_VOL_CUR_CALIB_UPD, 375 RK817_VOL_CUR_CALIB_UPD); 376 } 377 378 /* Update reported charge. */ 379 regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_Q_PRES_H3, 380 bulk_reg, 4); 381 tmp = get_unaligned_be32(bulk_reg); 382 charger->charge_now_uah = ADC_TO_CHARGE_UAH(tmp, charger->res_div); 383 if (charger->charge_now_uah < 0) 384 charger->charge_now_uah = 0; 385 if (charger->charge_now_uah > charger->fcc_mah * 1000) 386 charger->charge_now_uah = charger->fcc_mah * 1000; 387 388 /* Update soc based on reported charge. */ 389 charger->soc = charger->charge_now_uah * 100 / charger->fcc_mah; 390 391 /* Update reported voltage. */ 392 regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_BAT_VOL_H, 393 bulk_reg, 2); 394 tmp = get_unaligned_be16(bulk_reg); 395 charger->volt_avg_uv = (charger->voltage_k * tmp) + 1000 * 396 charger->voltage_b; 397 398 /* 399 * Update reported current. Note value from registers is a signed 16 400 * bit int. 401 */ 402 regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_BAT_CUR_H, 403 bulk_reg, 2); 404 tmp = (short int)get_unaligned_be16(bulk_reg); 405 charger->cur_avg_ua = ADC_TO_CURRENT(tmp, charger->res_div); 406 407 /* 408 * Update the max charge current. This value shouldn't change, but we 409 * can read it to report what the PMIC says it is instead of simply 410 * returning the default value. 411 */ 412 regmap_read(charger->rk808->regmap, RK817_PMIC_CHRG_OUT, ®); 413 charger->max_chg_cur_ua = 414 rk817_chg_cur_from_reg(reg & RK817_CHRG_CUR_SEL); 415 416 /* 417 * Update max charge voltage. Like the max charge current this value 418 * shouldn't change, but we can report what the PMIC says. 419 */ 420 regmap_read(charger->rk808->regmap, RK817_PMIC_CHRG_OUT, ®); 421 charger->max_chg_volt_uv = ((((reg & RK817_CHRG_VOL_SEL) >> 4) * 422 50000) + 4100000); 423 424 /* Check if battery still present. */ 425 regmap_read(charger->rk808->regmap, RK817_PMIC_CHRG_STS, ®); 426 charger->battery_present = (reg & RK817_BAT_EXS); 427 428 /* Get which type of charge we are using (if any). */ 429 regmap_read(charger->rk808->regmap, RK817_PMIC_CHRG_STS, ®); 430 charger->charge_status = (reg >> 4) & 0x07; 431 432 /* 433 * Get charger input voltage. Note that on my example hardware (an 434 * Odroid Go Advance) the voltage of the power connector is measured 435 * on the register labelled USB in the datasheet; I don't know if this 436 * is how it is designed or just a quirk of the implementation. I 437 * believe this will also measure the voltage of the USB output when in 438 * OTG mode, if that is the case we may need to change this in the 439 * future to return 0 if the power supply status is offline (I can't 440 * test this with my current implementation. Also, when the voltage 441 * should be zero sometimes the ADC still shows a single bit (which 442 * would register as 20000uv). When this happens set it to 0. 443 */ 444 regmap_bulk_read(charger->rk808->regmap, RK817_GAS_GAUGE_USB_VOL_H, 445 bulk_reg, 2); 446 reg = get_unaligned_be16(bulk_reg); 447 if (reg > 1) { 448 tmp = ((charger->voltage_k * reg / 1000 + charger->voltage_b) * 449 60 / 46); 450 charger->charger_input_volt_avg_uv = tmp * 1000; 451 } else { 452 charger->charger_input_volt_avg_uv = 0; 453 } 454 455 /* Calibrate battery capacity and soc. */ 456 rk817_bat_calib_cap(charger); 457 } 458 459 static int rk817_bat_get_prop(struct power_supply *ps, 460 enum power_supply_property prop, 461 union power_supply_propval *val) 462 { 463 struct rk817_charger *charger = power_supply_get_drvdata(ps); 464 465 switch (prop) { 466 case POWER_SUPPLY_PROP_PRESENT: 467 val->intval = charger->battery_present; 468 break; 469 case POWER_SUPPLY_PROP_STATUS: 470 if (charger->cur_avg_ua < 0) { 471 val->intval = POWER_SUPPLY_STATUS_DISCHARGING; 472 break; 473 } 474 switch (charger->charge_status) { 475 case CHRG_OFF: 476 val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING; 477 break; 478 /* 479 * Dead charge is documented, but not explained. I never 480 * observed it but assume it's a pre-charge for a dead 481 * battery. 482 */ 483 case DEAD_CHRG: 484 case TRICKLE_CHRG: 485 case CC_OR_CV_CHRG: 486 val->intval = POWER_SUPPLY_STATUS_CHARGING; 487 break; 488 case CHARGE_FINISH: 489 val->intval = POWER_SUPPLY_STATUS_FULL; 490 break; 491 default: 492 val->intval = POWER_SUPPLY_STATUS_UNKNOWN; 493 return -EINVAL; 494 495 } 496 break; 497 case POWER_SUPPLY_PROP_CHARGE_TYPE: 498 switch (charger->charge_status) { 499 case CHRG_OFF: 500 case CHARGE_FINISH: 501 val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE; 502 break; 503 case TRICKLE_CHRG: 504 val->intval = POWER_SUPPLY_CHARGE_TYPE_TRICKLE; 505 break; 506 case DEAD_CHRG: 507 case CC_OR_CV_CHRG: 508 val->intval = POWER_SUPPLY_CHARGE_TYPE_STANDARD; 509 break; 510 default: 511 val->intval = POWER_SUPPLY_CHARGE_TYPE_UNKNOWN; 512 break; 513 } 514 break; 515 case POWER_SUPPLY_PROP_CHARGE_FULL: 516 val->intval = charger->fcc_mah * 1000; 517 break; 518 case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN: 519 val->intval = charger->bat_charge_full_design_uah; 520 break; 521 case POWER_SUPPLY_PROP_CHARGE_EMPTY_DESIGN: 522 val->intval = 0; 523 break; 524 case POWER_SUPPLY_PROP_CHARGE_NOW: 525 val->intval = charger->charge_now_uah; 526 break; 527 case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN: 528 val->intval = charger->bat_voltage_min_design_uv; 529 break; 530 case POWER_SUPPLY_PROP_CAPACITY: 531 /* Add 500 so that values like 99999 are 100% not 99%. */ 532 val->intval = (charger->soc + 500) / 1000; 533 if (val->intval > 100) 534 val->intval = 100; 535 if (val->intval < 0) 536 val->intval = 0; 537 break; 538 case POWER_SUPPLY_PROP_VOLTAGE_AVG: 539 val->intval = charger->volt_avg_uv; 540 break; 541 case POWER_SUPPLY_PROP_CURRENT_AVG: 542 val->intval = charger->cur_avg_ua; 543 break; 544 case POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX: 545 val->intval = charger->max_chg_cur_ua; 546 break; 547 case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX: 548 val->intval = charger->max_chg_volt_uv; 549 break; 550 case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN: 551 val->intval = charger->bat_voltage_max_design_uv; 552 break; 553 default: 554 return -EINVAL; 555 } 556 return 0; 557 } 558 559 static int rk817_chg_get_prop(struct power_supply *ps, 560 enum power_supply_property prop, 561 union power_supply_propval *val) 562 { 563 struct rk817_charger *charger = power_supply_get_drvdata(ps); 564 565 switch (prop) { 566 case POWER_SUPPLY_PROP_ONLINE: 567 val->intval = charger->plugged_in; 568 break; 569 case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN: 570 /* max voltage from datasheet at 5.5v (default 5.0v) */ 571 val->intval = 5500000; 572 break; 573 case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN: 574 /* min voltage from datasheet at 3.8v (default 5.0v) */ 575 val->intval = 3800000; 576 break; 577 case POWER_SUPPLY_PROP_VOLTAGE_AVG: 578 val->intval = charger->charger_input_volt_avg_uv; 579 break; 580 /* 581 * While it's possible that other implementations could use different 582 * USB types, the current implementation for this PMIC (the Odroid Go 583 * Advance) only uses a dedicated charging port with no rx/tx lines. 584 */ 585 case POWER_SUPPLY_PROP_USB_TYPE: 586 val->intval = POWER_SUPPLY_USB_TYPE_DCP; 587 break; 588 default: 589 return -EINVAL; 590 } 591 return 0; 592 593 } 594 595 static irqreturn_t rk817_plug_in_isr(int irq, void *cg) 596 { 597 struct rk817_charger *charger; 598 599 charger = (struct rk817_charger *)cg; 600 charger->plugged_in = 1; 601 power_supply_changed(charger->chg_ps); 602 power_supply_changed(charger->bat_ps); 603 /* try to recalibrate capacity if we hit full charge. */ 604 charger->soc_cal = 0; 605 606 rk817_read_props(charger); 607 608 dev_dbg(charger->dev, "Power Cord Inserted\n"); 609 610 return IRQ_HANDLED; 611 } 612 613 static irqreturn_t rk817_plug_out_isr(int irq, void *cg) 614 { 615 struct rk817_charger *charger; 616 struct rk808 *rk808; 617 618 charger = (struct rk817_charger *)cg; 619 rk808 = charger->rk808; 620 charger->plugged_in = 0; 621 power_supply_changed(charger->bat_ps); 622 power_supply_changed(charger->chg_ps); 623 624 /* 625 * For some reason the bits of RK817_PMIC_CHRG_IN reset whenever the 626 * power cord is unplugged. This was not documented in the BSP kernel 627 * or the datasheet and only discovered by trial and error. Set minimum 628 * USB input voltage to 4.5v and enable USB voltage input limit. 629 */ 630 regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, 631 RK817_USB_VLIM_SEL, (0x05 << 4)); 632 regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, RK817_USB_VLIM_EN, 633 (0x01 << 7)); 634 635 /* 636 * Set average USB input current limit to 1.5A and enable USB current 637 * input limit. 638 */ 639 regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, 640 RK817_USB_ILIM_SEL, 0x03); 641 regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, RK817_USB_ILIM_EN, 642 (0x01 << 3)); 643 644 rk817_read_props(charger); 645 646 dev_dbg(charger->dev, "Power Cord Removed\n"); 647 648 return IRQ_HANDLED; 649 } 650 651 static enum power_supply_property rk817_bat_props[] = { 652 POWER_SUPPLY_PROP_PRESENT, 653 POWER_SUPPLY_PROP_STATUS, 654 POWER_SUPPLY_PROP_CHARGE_TYPE, 655 POWER_SUPPLY_PROP_CHARGE_FULL, 656 POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN, 657 POWER_SUPPLY_PROP_CHARGE_EMPTY_DESIGN, 658 POWER_SUPPLY_PROP_CHARGE_NOW, 659 POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE_MAX, 660 POWER_SUPPLY_PROP_VOLTAGE_AVG, 661 POWER_SUPPLY_PROP_CONSTANT_CHARGE_CURRENT_MAX, 662 POWER_SUPPLY_PROP_CURRENT_AVG, 663 POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN, 664 POWER_SUPPLY_PROP_CAPACITY, 665 POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN, 666 }; 667 668 static enum power_supply_property rk817_chg_props[] = { 669 POWER_SUPPLY_PROP_ONLINE, 670 POWER_SUPPLY_PROP_USB_TYPE, 671 POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN, 672 POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN, 673 POWER_SUPPLY_PROP_VOLTAGE_AVG, 674 }; 675 676 static enum power_supply_usb_type rk817_usb_type[] = { 677 POWER_SUPPLY_USB_TYPE_DCP, 678 POWER_SUPPLY_USB_TYPE_UNKNOWN, 679 }; 680 681 static const struct power_supply_desc rk817_bat_desc = { 682 .name = "rk817-battery", 683 .type = POWER_SUPPLY_TYPE_BATTERY, 684 .properties = rk817_bat_props, 685 .num_properties = ARRAY_SIZE(rk817_bat_props), 686 .get_property = rk817_bat_get_prop, 687 }; 688 689 static const struct power_supply_desc rk817_chg_desc = { 690 .name = "rk817-charger", 691 .type = POWER_SUPPLY_TYPE_USB, 692 .usb_types = rk817_usb_type, 693 .num_usb_types = ARRAY_SIZE(rk817_usb_type), 694 .properties = rk817_chg_props, 695 .num_properties = ARRAY_SIZE(rk817_chg_props), 696 .get_property = rk817_chg_get_prop, 697 }; 698 699 static int rk817_read_battery_nvram_values(struct rk817_charger *charger) 700 { 701 u8 bulk_reg[3]; 702 int ret; 703 704 /* Read the nvram data for full charge capacity. */ 705 ret = regmap_bulk_read(charger->rk808->regmap, 706 RK817_GAS_GAUGE_DATA3, bulk_reg, 3); 707 if (ret < 0) 708 return ret; 709 charger->fcc_mah = get_unaligned_le24(bulk_reg); 710 711 /* 712 * Sanity checking for values equal to zero or less than would be 713 * practical for this device (BSP Kernel assumes 500mAH or less) for 714 * practicality purposes. Also check if the value is too large and 715 * correct it. 716 */ 717 if ((charger->fcc_mah < 500) || 718 ((charger->fcc_mah * 1000) > charger->bat_charge_full_design_uah)) { 719 dev_info(charger->dev, 720 "Invalid NVRAM max charge, setting to %u uAH\n", 721 charger->bat_charge_full_design_uah); 722 charger->fcc_mah = charger->bat_charge_full_design_uah / 1000; 723 } 724 725 /* 726 * Read the nvram for state of charge. Sanity check for values greater 727 * than 100 (10000) or less than 0, because other things (BSP kernels, 728 * U-Boot, or even i2cset) can write to this register. If the value is 729 * off it should get corrected automatically when the voltage drops to 730 * the min (soc is 0) or when the battery is full (soc is 100). 731 */ 732 ret = regmap_bulk_read(charger->rk808->regmap, 733 RK817_GAS_GAUGE_BAT_R1, bulk_reg, 3); 734 if (ret < 0) 735 return ret; 736 charger->soc = get_unaligned_le24(bulk_reg); 737 if (charger->soc > 10000) 738 charger->soc = 10000; 739 if (charger->soc < 0) 740 charger->soc = 0; 741 742 return 0; 743 } 744 745 static int 746 rk817_read_or_set_full_charge_on_boot(struct rk817_charger *charger, 747 struct power_supply_battery_info *bat_info) 748 { 749 struct rk808 *rk808 = charger->rk808; 750 u8 bulk_reg[4]; 751 u32 boot_voltage, boot_charge_mah; 752 int ret, reg, off_time, tmp; 753 bool first_boot; 754 755 /* 756 * Check if the battery is uninitalized. If it is, the columb counter 757 * needs to be set up. 758 */ 759 ret = regmap_read(rk808->regmap, RK817_GAS_GAUGE_GG_STS, ®); 760 if (ret < 0) 761 return ret; 762 first_boot = reg & RK817_BAT_CON; 763 /* 764 * If the battery is uninitialized, use the poweron voltage and an ocv 765 * lookup to guess our charge. The number won't be very accurate until 766 * we hit either our minimum voltage (0%) or full charge (100%). 767 */ 768 if (first_boot) { 769 regmap_bulk_read(rk808->regmap, RK817_GAS_GAUGE_PWRON_VOL_H, 770 bulk_reg, 2); 771 tmp = get_unaligned_be16(bulk_reg); 772 boot_voltage = (charger->voltage_k * tmp) + 773 1000 * charger->voltage_b; 774 /* 775 * Since only implementation has no working thermistor, assume 776 * 20C for OCV lookup. If lookup fails, report error with OCV 777 * table. 778 */ 779 charger->soc = power_supply_batinfo_ocv2cap(bat_info, 780 boot_voltage, 781 20) * 1000; 782 if (charger->soc < 0) 783 charger->soc = 0; 784 785 /* Guess that full charge capacity is the design capacity */ 786 charger->fcc_mah = charger->bat_charge_full_design_uah / 1000; 787 /* 788 * Set battery as "set up". BSP driver uses this value even 789 * though datasheet claims it's a read-only value. 790 */ 791 regmap_write_bits(rk808->regmap, RK817_GAS_GAUGE_GG_STS, 792 RK817_BAT_CON, 0); 793 /* Save nvram values */ 794 ret = rk817_record_battery_nvram_values(charger); 795 if (ret < 0) 796 return ret; 797 } else { 798 ret = rk817_read_battery_nvram_values(charger); 799 if (ret < 0) 800 return ret; 801 802 regmap_bulk_read(rk808->regmap, RK817_GAS_GAUGE_Q_PRES_H3, 803 bulk_reg, 4); 804 tmp = get_unaligned_be32(bulk_reg); 805 if (tmp < 0) 806 tmp = 0; 807 boot_charge_mah = ADC_TO_CHARGE_UAH(tmp, 808 charger->res_div) / 1000; 809 /* 810 * Check if the columb counter has been off for more than 30 811 * minutes as it tends to drift downward. If so, re-init soc 812 * with the boot voltage instead. Note the unit values for the 813 * OFF_CNT register appear to be in decaminutes and stops 814 * counting at 2550 (0xFF) minutes. BSP kernel used OCV, but 815 * for me occasionally that would show invalid values. Boot 816 * voltage is only accurate for me on first poweron (not 817 * reboots), but we shouldn't ever encounter an OFF_CNT more 818 * than 0 on a reboot anyway. 819 */ 820 regmap_read(rk808->regmap, RK817_GAS_GAUGE_OFF_CNT, &off_time); 821 if (off_time >= 3) { 822 regmap_bulk_read(rk808->regmap, 823 RK817_GAS_GAUGE_PWRON_VOL_H, 824 bulk_reg, 2); 825 tmp = get_unaligned_be16(bulk_reg); 826 boot_voltage = (charger->voltage_k * tmp) + 827 1000 * charger->voltage_b; 828 charger->soc = 829 power_supply_batinfo_ocv2cap(bat_info, 830 boot_voltage, 831 20) * 1000; 832 } else { 833 charger->soc = (boot_charge_mah * 1000 * 100 / 834 charger->fcc_mah); 835 } 836 } 837 838 /* 839 * Now we have our full charge capacity and soc, init the columb 840 * counter. 841 */ 842 boot_charge_mah = charger->soc * charger->fcc_mah / 100 / 1000; 843 if (boot_charge_mah > charger->fcc_mah) 844 boot_charge_mah = charger->fcc_mah; 845 tmp = CHARGE_TO_ADC(boot_charge_mah, charger->res_div); 846 put_unaligned_be32(tmp, bulk_reg); 847 ret = regmap_bulk_write(rk808->regmap, RK817_GAS_GAUGE_Q_INIT_H3, 848 bulk_reg, 4); 849 if (ret < 0) 850 return ret; 851 852 /* Set QMAX value to max design capacity. */ 853 tmp = CHARGE_TO_ADC((charger->bat_charge_full_design_uah / 1000), 854 charger->res_div); 855 put_unaligned_be32(tmp, bulk_reg); 856 ret = regmap_bulk_write(rk808->regmap, RK817_GAS_GAUGE_Q_MAX_H3, 857 bulk_reg, 4); 858 if (ret < 0) 859 return ret; 860 861 return 0; 862 } 863 864 static int rk817_battery_init(struct rk817_charger *charger, 865 struct power_supply_battery_info *bat_info) 866 { 867 struct rk808 *rk808 = charger->rk808; 868 u32 tmp, max_chg_vol_mv, max_chg_cur_ma; 869 u8 max_chg_vol_reg, chg_term_i_reg; 870 int ret, chg_term_ma, max_chg_cur_reg; 871 u8 bulk_reg[2]; 872 873 /* Get initial plug state */ 874 regmap_read(rk808->regmap, RK817_SYS_STS, &tmp); 875 charger->plugged_in = (tmp & RK817_PLUG_IN_STS); 876 877 /* 878 * Turn on all ADC functions to measure battery, USB, and sys voltage, 879 * as well as batt temp. Note only tested implementation so far does 880 * not use a battery with a thermistor. 881 */ 882 regmap_write(rk808->regmap, RK817_GAS_GAUGE_ADC_CONFIG0, 0xfc); 883 884 /* 885 * Set relax mode voltage sampling interval and ADC offset calibration 886 * interval to 8 minutes to mirror BSP kernel. Set voltage and current 887 * modes to average to mirror BSP kernel. 888 */ 889 regmap_write(rk808->regmap, RK817_GAS_GAUGE_GG_CON, 0x04); 890 891 /* Calibrate voltage like the BSP does here. */ 892 rk817_bat_calib_vol(charger); 893 894 /* Write relax threshold, derived from sleep enter current. */ 895 tmp = CURRENT_TO_ADC(charger->sleep_enter_current_ua, 896 charger->res_div); 897 put_unaligned_be16(tmp, bulk_reg); 898 regmap_bulk_write(rk808->regmap, RK817_GAS_GAUGE_RELAX_THRE_H, 899 bulk_reg, 2); 900 901 /* Write sleep sample current, derived from sleep filter current. */ 902 tmp = CURRENT_TO_ADC(charger->sleep_filter_current_ua, 903 charger->res_div); 904 put_unaligned_be16(tmp, bulk_reg); 905 regmap_bulk_write(rk808->regmap, RK817_GAS_GAUGE_SLEEP_CON_SAMP_CUR_H, 906 bulk_reg, 2); 907 908 /* Restart battery relax voltage */ 909 regmap_write_bits(rk808->regmap, RK817_GAS_GAUGE_GG_STS, 910 RK817_RELAX_VOL_UPD, (0x0 << 2)); 911 912 /* 913 * Set OCV Threshold Voltage to 127.5mV. This was hard coded like this 914 * in the BSP. 915 */ 916 regmap_write(rk808->regmap, RK817_GAS_GAUGE_OCV_THRE_VOL, 0xff); 917 918 /* 919 * Set maximum charging voltage to battery max voltage. Trying to be 920 * incredibly safe with these value, as setting them wrong could 921 * overcharge the battery, which would be very bad. 922 */ 923 max_chg_vol_mv = bat_info->constant_charge_voltage_max_uv / 1000; 924 max_chg_cur_ma = bat_info->constant_charge_current_max_ua / 1000; 925 926 if (max_chg_vol_mv < 4100) { 927 return dev_err_probe(charger->dev, -EINVAL, 928 "invalid max charger voltage, value %u unsupported\n", 929 max_chg_vol_mv * 1000); 930 } 931 if (max_chg_vol_mv > 4450) { 932 dev_info(charger->dev, 933 "Setting max charge voltage to 4450000uv\n"); 934 max_chg_vol_mv = 4450; 935 } 936 937 if (max_chg_cur_ma < 500) { 938 return dev_err_probe(charger->dev, -EINVAL, 939 "invalid max charger current, value %u unsupported\n", 940 max_chg_cur_ma * 1000); 941 } 942 if (max_chg_cur_ma > 3500) 943 dev_info(charger->dev, 944 "Setting max charge current to 3500000ua\n"); 945 946 /* 947 * Now that the values are sanity checked, if we subtract 4100 from the 948 * max voltage and divide by 50, we conviently get the exact value for 949 * the registers, which are 4.1v, 4.15v, 4.2v, 4.25v, 4.3v, 4.35v, 950 * 4.4v, and 4.45v; these correspond to values 0x00 through 0x07. 951 */ 952 max_chg_vol_reg = (max_chg_vol_mv - 4100) / 50; 953 954 max_chg_cur_reg = rk817_chg_cur_to_reg(max_chg_cur_ma); 955 956 if (max_chg_vol_reg < 0 || max_chg_vol_reg > 7) { 957 return dev_err_probe(charger->dev, -EINVAL, 958 "invalid max charger voltage, value %u unsupported\n", 959 max_chg_vol_mv * 1000); 960 } 961 if (max_chg_cur_reg < 0 || max_chg_cur_reg > 7) { 962 return dev_err_probe(charger->dev, -EINVAL, 963 "invalid max charger current, value %u unsupported\n", 964 max_chg_cur_ma * 1000); 965 } 966 967 /* 968 * Write the values to the registers, and deliver an emergency warning 969 * in the event they are not written correctly. 970 */ 971 ret = regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_OUT, 972 RK817_CHRG_VOL_SEL, (max_chg_vol_reg << 4)); 973 if (ret) { 974 dev_emerg(charger->dev, 975 "Danger, unable to set max charger voltage: %u\n", 976 ret); 977 } 978 979 ret = regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_OUT, 980 RK817_CHRG_CUR_SEL, max_chg_cur_reg); 981 if (ret) { 982 dev_emerg(charger->dev, 983 "Danger, unable to set max charger current: %u\n", 984 ret); 985 } 986 987 /* Set charge finishing mode to analog */ 988 regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_TERM, 989 RK817_CHRG_TERM_ANA_DIG, (0x0 << 2)); 990 991 /* 992 * Set charge finish current, warn if value not in range and keep 993 * default. 994 */ 995 chg_term_ma = bat_info->charge_term_current_ua / 1000; 996 if (chg_term_ma < 150 || chg_term_ma > 400) { 997 dev_warn(charger->dev, 998 "Invalid charge termination %u, keeping default\n", 999 chg_term_ma * 1000); 1000 chg_term_ma = 200; 1001 } 1002 1003 /* 1004 * Values of 150ma, 200ma, 300ma, and 400ma correspond to 00, 01, 10, 1005 * and 11. 1006 */ 1007 chg_term_i_reg = (chg_term_ma - 100) / 100; 1008 regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_TERM, 1009 RK817_CHRG_TERM_ANA_SEL, chg_term_i_reg); 1010 1011 ret = rk817_read_or_set_full_charge_on_boot(charger, bat_info); 1012 if (ret < 0) 1013 return ret; 1014 1015 /* 1016 * Set minimum USB input voltage to 4.5v and enable USB voltage input 1017 * limit. 1018 */ 1019 regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, 1020 RK817_USB_VLIM_SEL, (0x05 << 4)); 1021 regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, RK817_USB_VLIM_EN, 1022 (0x01 << 7)); 1023 1024 /* 1025 * Set average USB input current limit to 1.5A and enable USB current 1026 * input limit. 1027 */ 1028 regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, 1029 RK817_USB_ILIM_SEL, 0x03); 1030 regmap_write_bits(rk808->regmap, RK817_PMIC_CHRG_IN, RK817_USB_ILIM_EN, 1031 (0x01 << 3)); 1032 1033 return 0; 1034 } 1035 1036 static void rk817_charging_monitor(struct work_struct *work) 1037 { 1038 struct rk817_charger *charger; 1039 1040 charger = container_of(work, struct rk817_charger, work.work); 1041 1042 rk817_read_props(charger); 1043 1044 /* Run every 8 seconds like the BSP driver did. */ 1045 queue_delayed_work(system_wq, &charger->work, msecs_to_jiffies(8000)); 1046 } 1047 1048 static int rk817_charger_probe(struct platform_device *pdev) 1049 { 1050 struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent); 1051 struct rk817_charger *charger; 1052 struct device_node *node; 1053 struct power_supply_battery_info *bat_info; 1054 struct device *dev = &pdev->dev; 1055 struct power_supply_config pscfg = {}; 1056 int plugin_irq, plugout_irq; 1057 int of_value; 1058 int ret; 1059 1060 node = of_get_child_by_name(dev->parent->of_node, "charger"); 1061 if (!node) 1062 return -ENODEV; 1063 1064 charger = devm_kzalloc(&pdev->dev, sizeof(*charger), GFP_KERNEL); 1065 if (!charger) { 1066 of_node_put(node); 1067 return -ENOMEM; 1068 } 1069 1070 charger->rk808 = rk808; 1071 1072 charger->dev = &pdev->dev; 1073 platform_set_drvdata(pdev, charger); 1074 1075 rk817_bat_calib_vol(charger); 1076 1077 pscfg.drv_data = charger; 1078 pscfg.of_node = node; 1079 1080 /* 1081 * Get sample resistor value. Note only values of 10000 or 20000 1082 * microohms are allowed. Schematic for my test implementation (an 1083 * Odroid Go Advance) shows a 10 milliohm resistor for reference. 1084 */ 1085 ret = of_property_read_u32(node, "rockchip,resistor-sense-micro-ohms", 1086 &of_value); 1087 if (ret < 0) { 1088 return dev_err_probe(dev, ret, 1089 "Error reading sample resistor value\n"); 1090 } 1091 /* 1092 * Store as a 1 or a 2, since all we really use the value for is as a 1093 * divisor in some calculations. 1094 */ 1095 charger->res_div = (of_value == 20000) ? 2 : 1; 1096 1097 /* 1098 * Get sleep enter current value. Not sure what this value is for 1099 * other than to help calibrate the relax threshold. 1100 */ 1101 ret = of_property_read_u32(node, 1102 "rockchip,sleep-enter-current-microamp", 1103 &of_value); 1104 if (ret < 0) { 1105 return dev_err_probe(dev, ret, 1106 "Error reading sleep enter cur value\n"); 1107 } 1108 charger->sleep_enter_current_ua = of_value; 1109 1110 /* Get sleep filter current value */ 1111 ret = of_property_read_u32(node, 1112 "rockchip,sleep-filter-current-microamp", 1113 &of_value); 1114 if (ret < 0) { 1115 return dev_err_probe(dev, ret, 1116 "Error reading sleep filter cur value\n"); 1117 } 1118 1119 charger->sleep_filter_current_ua = of_value; 1120 1121 charger->bat_ps = devm_power_supply_register(&pdev->dev, 1122 &rk817_bat_desc, &pscfg); 1123 if (IS_ERR(charger->bat_ps)) 1124 return dev_err_probe(dev, -EINVAL, 1125 "Battery failed to probe\n"); 1126 1127 charger->chg_ps = devm_power_supply_register(&pdev->dev, 1128 &rk817_chg_desc, &pscfg); 1129 if (IS_ERR(charger->chg_ps)) 1130 return dev_err_probe(dev, -EINVAL, 1131 "Charger failed to probe\n"); 1132 1133 ret = power_supply_get_battery_info(charger->bat_ps, 1134 &bat_info); 1135 if (ret) { 1136 return dev_err_probe(dev, ret, 1137 "Unable to get battery info\n"); 1138 } 1139 1140 if ((bat_info->charge_full_design_uah <= 0) || 1141 (bat_info->voltage_min_design_uv <= 0) || 1142 (bat_info->voltage_max_design_uv <= 0) || 1143 (bat_info->constant_charge_voltage_max_uv <= 0) || 1144 (bat_info->constant_charge_current_max_ua <= 0) || 1145 (bat_info->charge_term_current_ua <= 0)) { 1146 return dev_err_probe(dev, -EINVAL, 1147 "Required bat info missing or invalid\n"); 1148 } 1149 1150 charger->bat_charge_full_design_uah = bat_info->charge_full_design_uah; 1151 charger->bat_voltage_min_design_uv = bat_info->voltage_min_design_uv; 1152 charger->bat_voltage_max_design_uv = bat_info->voltage_max_design_uv; 1153 1154 /* 1155 * Has to run after power_supply_get_battery_info as it depends on some 1156 * values discovered from that routine. 1157 */ 1158 ret = rk817_battery_init(charger, bat_info); 1159 if (ret) 1160 return ret; 1161 1162 power_supply_put_battery_info(charger->bat_ps, bat_info); 1163 1164 plugin_irq = platform_get_irq(pdev, 0); 1165 if (plugin_irq < 0) 1166 return plugin_irq; 1167 1168 plugout_irq = platform_get_irq(pdev, 1); 1169 if (plugout_irq < 0) 1170 return plugout_irq; 1171 1172 ret = devm_request_threaded_irq(charger->dev, plugin_irq, NULL, 1173 rk817_plug_in_isr, 1174 IRQF_TRIGGER_RISING | IRQF_ONESHOT, 1175 "rk817_plug_in", charger); 1176 if (ret) { 1177 return dev_err_probe(&pdev->dev, ret, 1178 "plug_in_irq request failed!\n"); 1179 } 1180 1181 ret = devm_request_threaded_irq(charger->dev, plugout_irq, NULL, 1182 rk817_plug_out_isr, 1183 IRQF_TRIGGER_RISING | IRQF_ONESHOT, 1184 "rk817_plug_out", charger); 1185 if (ret) { 1186 return dev_err_probe(&pdev->dev, ret, 1187 "plug_out_irq request failed!\n"); 1188 } 1189 1190 ret = devm_delayed_work_autocancel(&pdev->dev, &charger->work, 1191 rk817_charging_monitor); 1192 if (ret) 1193 return ret; 1194 1195 /* Force the first update immediately. */ 1196 mod_delayed_work(system_wq, &charger->work, 0); 1197 1198 return 0; 1199 } 1200 1201 1202 static struct platform_driver rk817_charger_driver = { 1203 .probe = rk817_charger_probe, 1204 .driver = { 1205 .name = "rk817-charger", 1206 }, 1207 }; 1208 module_platform_driver(rk817_charger_driver); 1209 1210 MODULE_DESCRIPTION("Battery power supply driver for RK817 PMIC"); 1211 MODULE_AUTHOR("Maya Matuszczyk <maccraft123mc@gmail.com>"); 1212 MODULE_AUTHOR("Chris Morgan <macromorgan@hotmail.com>"); 1213 MODULE_LICENSE("GPL"); 1214