1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Battery driver for CPCAP PMIC 4 * 5 * Copyright (C) 2017 Tony Lindgren <tony@atomide.com> 6 * 7 * Some parts of the code based on earlier Motorola mapphone Linux kernel 8 * drivers: 9 * 10 * Copyright (C) 2009-2010 Motorola, Inc. 11 */ 12 13 #include <linux/delay.h> 14 #include <linux/err.h> 15 #include <linux/interrupt.h> 16 #include <linux/kernel.h> 17 #include <linux/module.h> 18 #include <linux/of_device.h> 19 #include <linux/platform_device.h> 20 #include <linux/power_supply.h> 21 #include <linux/reboot.h> 22 #include <linux/regmap.h> 23 #include <linux/nvmem-consumer.h> 24 #include <linux/moduleparam.h> 25 26 #include <linux/iio/consumer.h> 27 #include <linux/iio/types.h> 28 #include <linux/mfd/motorola-cpcap.h> 29 30 /* 31 * Register bit defines for CPCAP_REG_BPEOL. Some of these seem to 32 * map to MC13783UG.pdf "Table 5-19. Register 13, Power Control 0" 33 * to enable BATTDETEN, LOBAT and EOL features. We currently use 34 * LOBAT interrupts instead of EOL. 35 */ 36 #define CPCAP_REG_BPEOL_BIT_EOL9 BIT(9) /* Set for EOL irq */ 37 #define CPCAP_REG_BPEOL_BIT_EOL8 BIT(8) /* Set for EOL irq */ 38 #define CPCAP_REG_BPEOL_BIT_UNKNOWN7 BIT(7) 39 #define CPCAP_REG_BPEOL_BIT_UNKNOWN6 BIT(6) 40 #define CPCAP_REG_BPEOL_BIT_UNKNOWN5 BIT(5) 41 #define CPCAP_REG_BPEOL_BIT_EOL_MULTI BIT(4) /* Set for multiple EOL irqs */ 42 #define CPCAP_REG_BPEOL_BIT_UNKNOWN3 BIT(3) 43 #define CPCAP_REG_BPEOL_BIT_UNKNOWN2 BIT(2) 44 #define CPCAP_REG_BPEOL_BIT_BATTDETEN BIT(1) /* Enable battery detect */ 45 #define CPCAP_REG_BPEOL_BIT_EOLSEL BIT(0) /* BPDET = 0, EOL = 1 */ 46 47 /* 48 * Register bit defines for CPCAP_REG_CCC1. These seem similar to the twl6030 49 * coulomb counter registers rather than the mc13892 registers. Both twl6030 50 * and mc13892 set bits 2 and 1 to reset and clear registers. But mc13892 51 * sets bit 0 to start the coulomb counter while twl6030 sets bit 0 to stop 52 * the coulomb counter like cpcap does. So for now, we use the twl6030 style 53 * naming for the registers. 54 */ 55 #define CPCAP_REG_CCC1_ACTIVE_MODE1 BIT(4) /* Update rate */ 56 #define CPCAP_REG_CCC1_ACTIVE_MODE0 BIT(3) /* Update rate */ 57 #define CPCAP_REG_CCC1_AUTOCLEAR BIT(2) /* Resets sample registers */ 58 #define CPCAP_REG_CCC1_CAL_EN BIT(1) /* Clears after write in 1s */ 59 #define CPCAP_REG_CCC1_PAUSE BIT(0) /* Stop counters, allow write */ 60 #define CPCAP_REG_CCC1_RESET_MASK (CPCAP_REG_CCC1_AUTOCLEAR | \ 61 CPCAP_REG_CCC1_CAL_EN) 62 63 #define CPCAP_REG_CCCC2_RATE1 BIT(5) 64 #define CPCAP_REG_CCCC2_RATE0 BIT(4) 65 #define CPCAP_REG_CCCC2_ENABLE BIT(3) 66 67 #define CPCAP_BATTERY_CC_SAMPLE_PERIOD_MS 250 68 69 #define CPCAP_BATTERY_EB41_HW4X_ID 0x9E 70 #define CPCAP_BATTERY_BW8X_ID 0x98 71 72 enum { 73 CPCAP_BATTERY_IIO_BATTDET, 74 CPCAP_BATTERY_IIO_VOLTAGE, 75 CPCAP_BATTERY_IIO_CHRG_CURRENT, 76 CPCAP_BATTERY_IIO_BATT_CURRENT, 77 CPCAP_BATTERY_IIO_NR, 78 }; 79 80 enum cpcap_battery_irq_action { 81 CPCAP_BATTERY_IRQ_ACTION_NONE, 82 CPCAP_BATTERY_IRQ_ACTION_CC_CAL_DONE, 83 CPCAP_BATTERY_IRQ_ACTION_BATTERY_LOW, 84 CPCAP_BATTERY_IRQ_ACTION_POWEROFF, 85 }; 86 87 struct cpcap_interrupt_desc { 88 const char *name; 89 struct list_head node; 90 int irq; 91 enum cpcap_battery_irq_action action; 92 }; 93 94 struct cpcap_battery_config { 95 int cd_factor; 96 struct power_supply_info info; 97 struct power_supply_battery_info bat; 98 }; 99 100 struct cpcap_coulomb_counter_data { 101 s32 sample; /* 24 or 32 bits */ 102 s32 accumulator; 103 s16 offset; /* 9 bits */ 104 s16 integrator; /* 13 or 16 bits */ 105 }; 106 107 enum cpcap_battery_state { 108 CPCAP_BATTERY_STATE_PREVIOUS, 109 CPCAP_BATTERY_STATE_LATEST, 110 CPCAP_BATTERY_STATE_EMPTY, 111 CPCAP_BATTERY_STATE_FULL, 112 CPCAP_BATTERY_STATE_NR, 113 }; 114 115 struct cpcap_battery_state_data { 116 int voltage; 117 int current_ua; 118 int counter_uah; 119 int temperature; 120 ktime_t time; 121 struct cpcap_coulomb_counter_data cc; 122 }; 123 124 struct cpcap_battery_ddata { 125 struct device *dev; 126 struct regmap *reg; 127 struct list_head irq_list; 128 struct iio_channel *channels[CPCAP_BATTERY_IIO_NR]; 129 struct power_supply *psy; 130 struct cpcap_battery_config config; 131 struct cpcap_battery_state_data state[CPCAP_BATTERY_STATE_NR]; 132 u32 cc_lsb; /* μAms per LSB */ 133 atomic_t active; 134 int charge_full; 135 int status; 136 u16 vendor; 137 bool check_nvmem; 138 unsigned int is_full:1; 139 }; 140 141 #define CPCAP_NO_BATTERY -400 142 143 static bool ignore_temperature_probe; 144 module_param(ignore_temperature_probe, bool, 0660); 145 146 static struct cpcap_battery_state_data * 147 cpcap_battery_get_state(struct cpcap_battery_ddata *ddata, 148 enum cpcap_battery_state state) 149 { 150 if (state >= CPCAP_BATTERY_STATE_NR) 151 return NULL; 152 153 return &ddata->state[state]; 154 } 155 156 static struct cpcap_battery_state_data * 157 cpcap_battery_latest(struct cpcap_battery_ddata *ddata) 158 { 159 return cpcap_battery_get_state(ddata, CPCAP_BATTERY_STATE_LATEST); 160 } 161 162 static struct cpcap_battery_state_data * 163 cpcap_battery_previous(struct cpcap_battery_ddata *ddata) 164 { 165 return cpcap_battery_get_state(ddata, CPCAP_BATTERY_STATE_PREVIOUS); 166 } 167 168 static struct cpcap_battery_state_data * 169 cpcap_battery_get_empty(struct cpcap_battery_ddata *ddata) 170 { 171 return cpcap_battery_get_state(ddata, CPCAP_BATTERY_STATE_EMPTY); 172 } 173 174 static struct cpcap_battery_state_data * 175 cpcap_battery_get_full(struct cpcap_battery_ddata *ddata) 176 { 177 return cpcap_battery_get_state(ddata, CPCAP_BATTERY_STATE_FULL); 178 } 179 180 static int cpcap_charger_battery_temperature(struct cpcap_battery_ddata *ddata, 181 int *value) 182 { 183 struct iio_channel *channel; 184 int error; 185 186 channel = ddata->channels[CPCAP_BATTERY_IIO_BATTDET]; 187 error = iio_read_channel_processed(channel, value); 188 if (error < 0) { 189 if (!ignore_temperature_probe) 190 dev_warn(ddata->dev, "%s failed: %i\n", __func__, error); 191 *value = CPCAP_NO_BATTERY; 192 193 return error; 194 } 195 196 *value /= 100; 197 198 return 0; 199 } 200 201 static int cpcap_battery_get_voltage(struct cpcap_battery_ddata *ddata) 202 { 203 struct iio_channel *channel; 204 int error, value = 0; 205 206 channel = ddata->channels[CPCAP_BATTERY_IIO_VOLTAGE]; 207 error = iio_read_channel_processed(channel, &value); 208 if (error < 0) { 209 dev_warn(ddata->dev, "%s failed: %i\n", __func__, error); 210 211 return 0; 212 } 213 214 return value * 1000; 215 } 216 217 static int cpcap_battery_get_current(struct cpcap_battery_ddata *ddata) 218 { 219 struct iio_channel *channel; 220 int error, value = 0; 221 222 channel = ddata->channels[CPCAP_BATTERY_IIO_BATT_CURRENT]; 223 error = iio_read_channel_processed(channel, &value); 224 if (error < 0) { 225 dev_warn(ddata->dev, "%s failed: %i\n", __func__, error); 226 227 return 0; 228 } 229 230 return value * 1000; 231 } 232 233 /** 234 * cpcap_battery_cc_raw_div - calculate and divide coulomb counter μAms values 235 * @ddata: device driver data 236 * @sample: coulomb counter sample value 237 * @accumulator: coulomb counter integrator value 238 * @offset: coulomb counter offset value 239 * @divider: conversion divider 240 * 241 * Note that cc_lsb and cc_dur values are from Motorola Linux kernel 242 * function data_get_avg_curr_ua() and seem to be based on measured test 243 * results. It also has the following comment: 244 * 245 * Adjustment factors are applied here as a temp solution per the test 246 * results. Need to work out a formal solution for this adjustment. 247 * 248 * A coulomb counter for similar hardware seems to be documented in 249 * "TWL6030 Gas Gauging Basics (Rev. A)" swca095a.pdf in chapter 250 * "10 Calculating Accumulated Current". We however follow what the 251 * Motorola mapphone Linux kernel is doing as there may be either a 252 * TI or ST coulomb counter in the PMIC. 253 */ 254 static int cpcap_battery_cc_raw_div(struct cpcap_battery_ddata *ddata, 255 s32 sample, s32 accumulator, 256 s16 offset, u32 divider) 257 { 258 s64 acc; 259 260 if (!divider) 261 return 0; 262 263 acc = accumulator; 264 acc -= (s64)sample * offset; 265 acc *= ddata->cc_lsb; 266 acc *= -1; 267 acc = div_s64(acc, divider); 268 269 return acc; 270 } 271 272 /* 3600000μAms = 1μAh */ 273 static int cpcap_battery_cc_to_uah(struct cpcap_battery_ddata *ddata, 274 s32 sample, s32 accumulator, 275 s16 offset) 276 { 277 return cpcap_battery_cc_raw_div(ddata, sample, 278 accumulator, offset, 279 3600000); 280 } 281 282 static int cpcap_battery_cc_to_ua(struct cpcap_battery_ddata *ddata, 283 s32 sample, s32 accumulator, 284 s16 offset) 285 { 286 return cpcap_battery_cc_raw_div(ddata, sample, 287 accumulator, offset, 288 sample * 289 CPCAP_BATTERY_CC_SAMPLE_PERIOD_MS); 290 } 291 292 /** 293 * cpcap_battery_read_accumulated - reads cpcap coulomb counter 294 * @ddata: device driver data 295 * @ccd: coulomb counter values 296 * 297 * Based on Motorola mapphone kernel function data_read_regs(). 298 * Looking at the registers, the coulomb counter seems similar to 299 * the coulomb counter in TWL6030. See "TWL6030 Gas Gauging Basics 300 * (Rev. A) swca095a.pdf for "10 Calculating Accumulated Current". 301 * 302 * Note that swca095a.pdf instructs to stop the coulomb counter 303 * before reading to avoid values changing. Motorola mapphone 304 * Linux kernel does not do it, so let's assume they've verified 305 * the data produced is correct. 306 */ 307 static int 308 cpcap_battery_read_accumulated(struct cpcap_battery_ddata *ddata, 309 struct cpcap_coulomb_counter_data *ccd) 310 { 311 u16 buf[7]; /* CPCAP_REG_CCS1 to CCI */ 312 int error; 313 314 ccd->sample = 0; 315 ccd->accumulator = 0; 316 ccd->offset = 0; 317 ccd->integrator = 0; 318 319 /* Read coulomb counter register range */ 320 error = regmap_bulk_read(ddata->reg, CPCAP_REG_CCS1, 321 buf, ARRAY_SIZE(buf)); 322 if (error) 323 return 0; 324 325 /* Sample value CPCAP_REG_CCS1 & 2 */ 326 ccd->sample = (buf[1] & 0x0fff) << 16; 327 ccd->sample |= buf[0]; 328 if (ddata->vendor == CPCAP_VENDOR_TI) 329 ccd->sample = sign_extend32(24, ccd->sample); 330 331 /* Accumulator value CPCAP_REG_CCA1 & 2 */ 332 ccd->accumulator = ((s16)buf[3]) << 16; 333 ccd->accumulator |= buf[2]; 334 335 /* 336 * Coulomb counter calibration offset is CPCAP_REG_CCM, 337 * REG_CCO seems unused 338 */ 339 ccd->offset = buf[4]; 340 ccd->offset = sign_extend32(ccd->offset, 9); 341 342 /* Integrator register CPCAP_REG_CCI */ 343 if (ddata->vendor == CPCAP_VENDOR_TI) 344 ccd->integrator = sign_extend32(buf[6], 13); 345 else 346 ccd->integrator = (s16)buf[6]; 347 348 return cpcap_battery_cc_to_uah(ddata, 349 ccd->sample, 350 ccd->accumulator, 351 ccd->offset); 352 } 353 354 355 /* 356 * Based on the values from Motorola mapphone Linux kernel for the 357 * stock Droid 4 battery eb41. In the Motorola mapphone Linux 358 * kernel tree the value for pm_cd_factor is passed to the kernel 359 * via device tree. If it turns out to be something device specific 360 * we can consider that too later. These values are also fine for 361 * Bionic's hw4x. 362 * 363 * And looking at the battery full and shutdown values for the stock 364 * kernel on droid 4, full is 4351000 and software initiates shutdown 365 * at 3078000. The device will die around 2743000. 366 */ 367 static const struct cpcap_battery_config cpcap_battery_eb41_data = { 368 .cd_factor = 0x3cc, 369 .info.technology = POWER_SUPPLY_TECHNOLOGY_LION, 370 .info.voltage_max_design = 4351000, 371 .info.voltage_min_design = 3100000, 372 .info.charge_full_design = 1740000, 373 .bat.constant_charge_voltage_max_uv = 4200000, 374 }; 375 376 /* Values for the extended Droid Bionic battery bw8x. */ 377 static const struct cpcap_battery_config cpcap_battery_bw8x_data = { 378 .cd_factor = 0x3cc, 379 .info.technology = POWER_SUPPLY_TECHNOLOGY_LION, 380 .info.voltage_max_design = 4200000, 381 .info.voltage_min_design = 3200000, 382 .info.charge_full_design = 2760000, 383 .bat.constant_charge_voltage_max_uv = 4200000, 384 }; 385 386 /* 387 * Safe values for any lipo battery likely to fit into a mapphone 388 * battery bay. 389 */ 390 static const struct cpcap_battery_config cpcap_battery_unkown_data = { 391 .cd_factor = 0x3cc, 392 .info.technology = POWER_SUPPLY_TECHNOLOGY_LION, 393 .info.voltage_max_design = 4200000, 394 .info.voltage_min_design = 3200000, 395 .info.charge_full_design = 3000000, 396 .bat.constant_charge_voltage_max_uv = 4200000, 397 }; 398 399 static int cpcap_battery_match_nvmem(struct device *dev, const void *data) 400 { 401 if (strcmp(dev_name(dev), "89-500029ba0f73") == 0) 402 return 1; 403 else 404 return 0; 405 } 406 407 static void cpcap_battery_detect_battery_type(struct cpcap_battery_ddata *ddata) 408 { 409 struct nvmem_device *nvmem; 410 u8 battery_id = 0; 411 412 ddata->check_nvmem = false; 413 414 nvmem = nvmem_device_find(NULL, &cpcap_battery_match_nvmem); 415 if (IS_ERR_OR_NULL(nvmem)) { 416 ddata->check_nvmem = true; 417 dev_info_once(ddata->dev, "Can not find battery nvmem device. Assuming generic lipo battery\n"); 418 } else if (nvmem_device_read(nvmem, 2, 1, &battery_id) < 0) { 419 battery_id = 0; 420 ddata->check_nvmem = true; 421 dev_warn(ddata->dev, "Can not read battery nvmem device. Assuming generic lipo battery\n"); 422 } 423 424 switch (battery_id) { 425 case CPCAP_BATTERY_EB41_HW4X_ID: 426 ddata->config = cpcap_battery_eb41_data; 427 break; 428 case CPCAP_BATTERY_BW8X_ID: 429 ddata->config = cpcap_battery_bw8x_data; 430 break; 431 default: 432 ddata->config = cpcap_battery_unkown_data; 433 } 434 } 435 436 /** 437 * cpcap_battery_cc_get_avg_current - read cpcap coulumb counter 438 * @ddata: cpcap battery driver device data 439 */ 440 static int cpcap_battery_cc_get_avg_current(struct cpcap_battery_ddata *ddata) 441 { 442 int value, acc, error; 443 s32 sample; 444 s16 offset; 445 446 /* Coulomb counter integrator */ 447 error = regmap_read(ddata->reg, CPCAP_REG_CCI, &value); 448 if (error) 449 return error; 450 451 if (ddata->vendor == CPCAP_VENDOR_TI) { 452 acc = sign_extend32(value, 13); 453 sample = 1; 454 } else { 455 acc = (s16)value; 456 sample = 4; 457 } 458 459 /* Coulomb counter calibration offset */ 460 error = regmap_read(ddata->reg, CPCAP_REG_CCM, &value); 461 if (error) 462 return error; 463 464 offset = sign_extend32(value, 9); 465 466 return cpcap_battery_cc_to_ua(ddata, sample, acc, offset); 467 } 468 469 static int cpcap_battery_get_charger_status(struct cpcap_battery_ddata *ddata, 470 int *val) 471 { 472 union power_supply_propval prop; 473 struct power_supply *charger; 474 int error; 475 476 charger = power_supply_get_by_name("usb"); 477 if (!charger) 478 return -ENODEV; 479 480 error = power_supply_get_property(charger, POWER_SUPPLY_PROP_STATUS, 481 &prop); 482 if (error) 483 *val = POWER_SUPPLY_STATUS_UNKNOWN; 484 else 485 *val = prop.intval; 486 487 power_supply_put(charger); 488 489 return error; 490 } 491 492 static bool cpcap_battery_full(struct cpcap_battery_ddata *ddata) 493 { 494 struct cpcap_battery_state_data *state = cpcap_battery_latest(ddata); 495 unsigned int vfull; 496 int error, val; 497 498 error = cpcap_battery_get_charger_status(ddata, &val); 499 if (!error) { 500 switch (val) { 501 case POWER_SUPPLY_STATUS_DISCHARGING: 502 dev_dbg(ddata->dev, "charger disconnected\n"); 503 ddata->is_full = 0; 504 break; 505 case POWER_SUPPLY_STATUS_FULL: 506 dev_dbg(ddata->dev, "charger full status\n"); 507 ddata->is_full = 1; 508 break; 509 default: 510 break; 511 } 512 } 513 514 /* 515 * The full battery voltage here can be inaccurate, it's used just to 516 * filter out any trickle charging events. We clear the is_full status 517 * on charger disconnect above anyways. 518 */ 519 vfull = ddata->config.bat.constant_charge_voltage_max_uv - 120000; 520 521 if (ddata->is_full && state->voltage < vfull) 522 ddata->is_full = 0; 523 524 return ddata->is_full; 525 } 526 527 static bool cpcap_battery_low(struct cpcap_battery_ddata *ddata) 528 { 529 struct cpcap_battery_state_data *state = cpcap_battery_latest(ddata); 530 static bool is_low; 531 532 if (state->current_ua > 0 && (state->voltage <= 3350000 || is_low)) 533 is_low = true; 534 else 535 is_low = false; 536 537 return is_low; 538 } 539 540 static int cpcap_battery_update_status(struct cpcap_battery_ddata *ddata) 541 { 542 struct cpcap_battery_state_data state, *latest, *previous, 543 *empty, *full; 544 ktime_t now; 545 int error; 546 547 memset(&state, 0, sizeof(state)); 548 now = ktime_get(); 549 550 latest = cpcap_battery_latest(ddata); 551 if (latest) { 552 s64 delta_ms = ktime_to_ms(ktime_sub(now, latest->time)); 553 554 if (delta_ms < CPCAP_BATTERY_CC_SAMPLE_PERIOD_MS) 555 return delta_ms; 556 } 557 558 state.time = now; 559 state.voltage = cpcap_battery_get_voltage(ddata); 560 state.current_ua = cpcap_battery_get_current(ddata); 561 state.counter_uah = cpcap_battery_read_accumulated(ddata, &state.cc); 562 563 error = cpcap_charger_battery_temperature(ddata, 564 &state.temperature); 565 if (error) 566 return error; 567 568 previous = cpcap_battery_previous(ddata); 569 memcpy(previous, latest, sizeof(*previous)); 570 memcpy(latest, &state, sizeof(*latest)); 571 572 if (cpcap_battery_full(ddata)) { 573 full = cpcap_battery_get_full(ddata); 574 memcpy(full, latest, sizeof(*full)); 575 576 empty = cpcap_battery_get_empty(ddata); 577 if (empty->voltage && empty->voltage != -1) { 578 empty->voltage = -1; 579 ddata->charge_full = 580 empty->counter_uah - full->counter_uah; 581 } else if (ddata->charge_full) { 582 empty->voltage = -1; 583 empty->counter_uah = 584 full->counter_uah + ddata->charge_full; 585 } 586 } else if (cpcap_battery_low(ddata)) { 587 empty = cpcap_battery_get_empty(ddata); 588 memcpy(empty, latest, sizeof(*empty)); 589 590 full = cpcap_battery_get_full(ddata); 591 if (full->voltage) { 592 full->voltage = 0; 593 ddata->charge_full = 594 empty->counter_uah - full->counter_uah; 595 } 596 } 597 598 return 0; 599 } 600 601 /* 602 * Update battery status when cpcap-charger calls power_supply_changed(). 603 * This allows us to detect battery full condition before the charger 604 * disconnects. 605 */ 606 static void cpcap_battery_external_power_changed(struct power_supply *psy) 607 { 608 union power_supply_propval prop; 609 610 power_supply_get_property(psy, POWER_SUPPLY_PROP_STATUS, &prop); 611 } 612 613 static enum power_supply_property cpcap_battery_props[] = { 614 POWER_SUPPLY_PROP_STATUS, 615 POWER_SUPPLY_PROP_PRESENT, 616 POWER_SUPPLY_PROP_TECHNOLOGY, 617 POWER_SUPPLY_PROP_VOLTAGE_NOW, 618 POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN, 619 POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN, 620 POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE, 621 POWER_SUPPLY_PROP_CURRENT_AVG, 622 POWER_SUPPLY_PROP_CURRENT_NOW, 623 POWER_SUPPLY_PROP_CHARGE_FULL, 624 POWER_SUPPLY_PROP_CHARGE_NOW, 625 POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN, 626 POWER_SUPPLY_PROP_CHARGE_COUNTER, 627 POWER_SUPPLY_PROP_POWER_NOW, 628 POWER_SUPPLY_PROP_POWER_AVG, 629 POWER_SUPPLY_PROP_CAPACITY, 630 POWER_SUPPLY_PROP_CAPACITY_LEVEL, 631 POWER_SUPPLY_PROP_SCOPE, 632 POWER_SUPPLY_PROP_TEMP, 633 }; 634 635 static int cpcap_battery_get_property(struct power_supply *psy, 636 enum power_supply_property psp, 637 union power_supply_propval *val) 638 { 639 struct cpcap_battery_ddata *ddata = power_supply_get_drvdata(psy); 640 struct cpcap_battery_state_data *latest, *previous, *empty; 641 u32 sample; 642 s32 accumulator; 643 int cached; 644 s64 tmp; 645 646 cached = cpcap_battery_update_status(ddata); 647 if (cached < 0) 648 return cached; 649 650 latest = cpcap_battery_latest(ddata); 651 previous = cpcap_battery_previous(ddata); 652 653 if (ddata->check_nvmem) 654 cpcap_battery_detect_battery_type(ddata); 655 656 switch (psp) { 657 case POWER_SUPPLY_PROP_PRESENT: 658 if (latest->temperature > CPCAP_NO_BATTERY || ignore_temperature_probe) 659 val->intval = 1; 660 else 661 val->intval = 0; 662 break; 663 case POWER_SUPPLY_PROP_STATUS: 664 if (cpcap_battery_full(ddata)) { 665 val->intval = POWER_SUPPLY_STATUS_FULL; 666 break; 667 } 668 if (cpcap_battery_cc_get_avg_current(ddata) < 0) 669 val->intval = POWER_SUPPLY_STATUS_CHARGING; 670 else 671 val->intval = POWER_SUPPLY_STATUS_DISCHARGING; 672 break; 673 case POWER_SUPPLY_PROP_TECHNOLOGY: 674 val->intval = ddata->config.info.technology; 675 break; 676 case POWER_SUPPLY_PROP_VOLTAGE_NOW: 677 val->intval = cpcap_battery_get_voltage(ddata); 678 break; 679 case POWER_SUPPLY_PROP_VOLTAGE_MAX_DESIGN: 680 val->intval = ddata->config.info.voltage_max_design; 681 break; 682 case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN: 683 val->intval = ddata->config.info.voltage_min_design; 684 break; 685 case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE: 686 val->intval = ddata->config.bat.constant_charge_voltage_max_uv; 687 break; 688 case POWER_SUPPLY_PROP_CURRENT_AVG: 689 sample = latest->cc.sample - previous->cc.sample; 690 if (!sample) { 691 val->intval = cpcap_battery_cc_get_avg_current(ddata); 692 break; 693 } 694 accumulator = latest->cc.accumulator - previous->cc.accumulator; 695 val->intval = cpcap_battery_cc_to_ua(ddata, sample, 696 accumulator, 697 latest->cc.offset); 698 break; 699 case POWER_SUPPLY_PROP_CURRENT_NOW: 700 val->intval = latest->current_ua; 701 break; 702 case POWER_SUPPLY_PROP_CHARGE_COUNTER: 703 val->intval = latest->counter_uah; 704 break; 705 case POWER_SUPPLY_PROP_POWER_NOW: 706 tmp = (latest->voltage / 10000) * latest->current_ua; 707 val->intval = div64_s64(tmp, 100); 708 break; 709 case POWER_SUPPLY_PROP_POWER_AVG: 710 sample = latest->cc.sample - previous->cc.sample; 711 if (!sample) { 712 tmp = cpcap_battery_cc_get_avg_current(ddata); 713 tmp *= (latest->voltage / 10000); 714 val->intval = div64_s64(tmp, 100); 715 break; 716 } 717 accumulator = latest->cc.accumulator - previous->cc.accumulator; 718 tmp = cpcap_battery_cc_to_ua(ddata, sample, accumulator, 719 latest->cc.offset); 720 tmp *= ((latest->voltage + previous->voltage) / 20000); 721 val->intval = div64_s64(tmp, 100); 722 break; 723 case POWER_SUPPLY_PROP_CAPACITY: 724 empty = cpcap_battery_get_empty(ddata); 725 if (!empty->voltage || !ddata->charge_full) 726 return -ENODATA; 727 /* (ddata->charge_full / 200) is needed for rounding */ 728 val->intval = empty->counter_uah - latest->counter_uah + 729 ddata->charge_full / 200; 730 val->intval = clamp(val->intval, 0, ddata->charge_full); 731 val->intval = val->intval * 100 / ddata->charge_full; 732 break; 733 case POWER_SUPPLY_PROP_CAPACITY_LEVEL: 734 if (cpcap_battery_full(ddata)) 735 val->intval = POWER_SUPPLY_CAPACITY_LEVEL_FULL; 736 else if (latest->voltage >= 3750000) 737 val->intval = POWER_SUPPLY_CAPACITY_LEVEL_HIGH; 738 else if (latest->voltage >= 3300000) 739 val->intval = POWER_SUPPLY_CAPACITY_LEVEL_NORMAL; 740 else if (latest->voltage > 3100000) 741 val->intval = POWER_SUPPLY_CAPACITY_LEVEL_LOW; 742 else if (latest->voltage <= 3100000) 743 val->intval = POWER_SUPPLY_CAPACITY_LEVEL_CRITICAL; 744 else 745 val->intval = POWER_SUPPLY_CAPACITY_LEVEL_UNKNOWN; 746 break; 747 case POWER_SUPPLY_PROP_CHARGE_NOW: 748 empty = cpcap_battery_get_empty(ddata); 749 if (!empty->voltage) 750 return -ENODATA; 751 val->intval = empty->counter_uah - latest->counter_uah; 752 if (val->intval < 0) { 753 /* Assume invalid config if CHARGE_NOW is -20% */ 754 if (ddata->charge_full && abs(val->intval) > ddata->charge_full/5) { 755 empty->voltage = 0; 756 ddata->charge_full = 0; 757 return -ENODATA; 758 } 759 val->intval = 0; 760 } else if (ddata->charge_full && ddata->charge_full < val->intval) { 761 /* Assume invalid config if CHARGE_NOW exceeds CHARGE_FULL by 20% */ 762 if (val->intval > (6*ddata->charge_full)/5) { 763 empty->voltage = 0; 764 ddata->charge_full = 0; 765 return -ENODATA; 766 } 767 val->intval = ddata->charge_full; 768 } 769 break; 770 case POWER_SUPPLY_PROP_CHARGE_FULL: 771 if (!ddata->charge_full) 772 return -ENODATA; 773 val->intval = ddata->charge_full; 774 break; 775 case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN: 776 val->intval = ddata->config.info.charge_full_design; 777 break; 778 case POWER_SUPPLY_PROP_SCOPE: 779 val->intval = POWER_SUPPLY_SCOPE_SYSTEM; 780 break; 781 case POWER_SUPPLY_PROP_TEMP: 782 if (ignore_temperature_probe) 783 return -ENODATA; 784 val->intval = latest->temperature; 785 break; 786 default: 787 return -EINVAL; 788 } 789 790 return 0; 791 } 792 793 static int cpcap_battery_update_charger(struct cpcap_battery_ddata *ddata, 794 int const_charge_voltage) 795 { 796 union power_supply_propval prop; 797 union power_supply_propval val; 798 struct power_supply *charger; 799 int error; 800 801 charger = power_supply_get_by_name("usb"); 802 if (!charger) 803 return -ENODEV; 804 805 error = power_supply_get_property(charger, 806 POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE, 807 &prop); 808 if (error) 809 goto out_put; 810 811 /* Allow charger const voltage lower than battery const voltage */ 812 if (const_charge_voltage > prop.intval) 813 goto out_put; 814 815 val.intval = const_charge_voltage; 816 817 error = power_supply_set_property(charger, 818 POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE, 819 &val); 820 out_put: 821 power_supply_put(charger); 822 823 return error; 824 } 825 826 static int cpcap_battery_set_property(struct power_supply *psy, 827 enum power_supply_property psp, 828 const union power_supply_propval *val) 829 { 830 struct cpcap_battery_ddata *ddata = power_supply_get_drvdata(psy); 831 832 switch (psp) { 833 case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE: 834 if (val->intval < ddata->config.info.voltage_min_design) 835 return -EINVAL; 836 if (val->intval > ddata->config.info.voltage_max_design) 837 return -EINVAL; 838 839 ddata->config.bat.constant_charge_voltage_max_uv = val->intval; 840 841 return cpcap_battery_update_charger(ddata, val->intval); 842 case POWER_SUPPLY_PROP_CHARGE_FULL: 843 if (val->intval < 0) 844 return -EINVAL; 845 if (val->intval > (6*ddata->config.info.charge_full_design)/5) 846 return -EINVAL; 847 848 ddata->charge_full = val->intval; 849 850 return 0; 851 default: 852 return -EINVAL; 853 } 854 855 return 0; 856 } 857 858 static int cpcap_battery_property_is_writeable(struct power_supply *psy, 859 enum power_supply_property psp) 860 { 861 switch (psp) { 862 case POWER_SUPPLY_PROP_CONSTANT_CHARGE_VOLTAGE: 863 case POWER_SUPPLY_PROP_CHARGE_FULL: 864 return 1; 865 default: 866 return 0; 867 } 868 } 869 870 static irqreturn_t cpcap_battery_irq_thread(int irq, void *data) 871 { 872 struct cpcap_battery_ddata *ddata = data; 873 struct cpcap_battery_state_data *latest; 874 struct cpcap_interrupt_desc *d; 875 876 if (!atomic_read(&ddata->active)) 877 return IRQ_NONE; 878 879 list_for_each_entry(d, &ddata->irq_list, node) { 880 if (irq == d->irq) 881 break; 882 } 883 884 if (list_entry_is_head(d, &ddata->irq_list, node)) 885 return IRQ_NONE; 886 887 latest = cpcap_battery_latest(ddata); 888 889 switch (d->action) { 890 case CPCAP_BATTERY_IRQ_ACTION_CC_CAL_DONE: 891 dev_info(ddata->dev, "Coulomb counter calibration done\n"); 892 break; 893 case CPCAP_BATTERY_IRQ_ACTION_BATTERY_LOW: 894 if (latest->current_ua >= 0) 895 dev_warn(ddata->dev, "Battery low at %imV!\n", 896 latest->voltage / 1000); 897 break; 898 case CPCAP_BATTERY_IRQ_ACTION_POWEROFF: 899 if (latest->current_ua >= 0 && latest->voltage <= 3200000) { 900 dev_emerg(ddata->dev, 901 "Battery empty at %imV, powering off\n", 902 latest->voltage / 1000); 903 orderly_poweroff(true); 904 } 905 break; 906 default: 907 break; 908 } 909 910 power_supply_changed(ddata->psy); 911 912 return IRQ_HANDLED; 913 } 914 915 static int cpcap_battery_init_irq(struct platform_device *pdev, 916 struct cpcap_battery_ddata *ddata, 917 const char *name) 918 { 919 struct cpcap_interrupt_desc *d; 920 int irq, error; 921 922 irq = platform_get_irq_byname(pdev, name); 923 if (irq < 0) 924 return irq; 925 926 error = devm_request_threaded_irq(ddata->dev, irq, NULL, 927 cpcap_battery_irq_thread, 928 IRQF_SHARED | IRQF_ONESHOT, 929 name, ddata); 930 if (error) { 931 dev_err(ddata->dev, "could not get irq %s: %i\n", 932 name, error); 933 934 return error; 935 } 936 937 d = devm_kzalloc(ddata->dev, sizeof(*d), GFP_KERNEL); 938 if (!d) 939 return -ENOMEM; 940 941 d->name = name; 942 d->irq = irq; 943 944 if (!strncmp(name, "cccal", 5)) 945 d->action = CPCAP_BATTERY_IRQ_ACTION_CC_CAL_DONE; 946 else if (!strncmp(name, "lowbph", 6)) 947 d->action = CPCAP_BATTERY_IRQ_ACTION_BATTERY_LOW; 948 else if (!strncmp(name, "lowbpl", 6)) 949 d->action = CPCAP_BATTERY_IRQ_ACTION_POWEROFF; 950 951 list_add(&d->node, &ddata->irq_list); 952 953 return 0; 954 } 955 956 static int cpcap_battery_init_interrupts(struct platform_device *pdev, 957 struct cpcap_battery_ddata *ddata) 958 { 959 static const char * const cpcap_battery_irqs[] = { 960 "eol", "lowbph", "lowbpl", 961 "chrgcurr1", "battdetb" 962 }; 963 int i, error; 964 965 for (i = 0; i < ARRAY_SIZE(cpcap_battery_irqs); i++) { 966 error = cpcap_battery_init_irq(pdev, ddata, 967 cpcap_battery_irqs[i]); 968 if (error) 969 return error; 970 } 971 972 /* Enable calibration interrupt if already available in dts */ 973 cpcap_battery_init_irq(pdev, ddata, "cccal"); 974 975 /* Enable low battery interrupts for 3.3V high and 3.1V low */ 976 error = regmap_update_bits(ddata->reg, CPCAP_REG_BPEOL, 977 0xffff, 978 CPCAP_REG_BPEOL_BIT_BATTDETEN); 979 if (error) 980 return error; 981 982 return 0; 983 } 984 985 static int cpcap_battery_init_iio(struct cpcap_battery_ddata *ddata) 986 { 987 const char * const names[CPCAP_BATTERY_IIO_NR] = { 988 "battdetb", "battp", "chg_isense", "batti", 989 }; 990 int error, i; 991 992 for (i = 0; i < CPCAP_BATTERY_IIO_NR; i++) { 993 ddata->channels[i] = devm_iio_channel_get(ddata->dev, 994 names[i]); 995 if (IS_ERR(ddata->channels[i])) { 996 error = PTR_ERR(ddata->channels[i]); 997 goto out_err; 998 } 999 1000 if (!ddata->channels[i]->indio_dev) { 1001 error = -ENXIO; 1002 goto out_err; 1003 } 1004 } 1005 1006 return 0; 1007 1008 out_err: 1009 return dev_err_probe(ddata->dev, error, 1010 "could not initialize VBUS or ID IIO\n"); 1011 } 1012 1013 /* Calibrate coulomb counter */ 1014 static int cpcap_battery_calibrate(struct cpcap_battery_ddata *ddata) 1015 { 1016 int error, ccc1, value; 1017 unsigned long timeout; 1018 1019 error = regmap_read(ddata->reg, CPCAP_REG_CCC1, &ccc1); 1020 if (error) 1021 return error; 1022 1023 timeout = jiffies + msecs_to_jiffies(6000); 1024 1025 /* Start calibration */ 1026 error = regmap_update_bits(ddata->reg, CPCAP_REG_CCC1, 1027 0xffff, 1028 CPCAP_REG_CCC1_CAL_EN); 1029 if (error) 1030 goto restore; 1031 1032 while (time_before(jiffies, timeout)) { 1033 error = regmap_read(ddata->reg, CPCAP_REG_CCC1, &value); 1034 if (error) 1035 goto restore; 1036 1037 if (!(value & CPCAP_REG_CCC1_CAL_EN)) 1038 break; 1039 1040 error = regmap_read(ddata->reg, CPCAP_REG_CCM, &value); 1041 if (error) 1042 goto restore; 1043 1044 msleep(300); 1045 } 1046 1047 /* Read calibration offset from CCM */ 1048 error = regmap_read(ddata->reg, CPCAP_REG_CCM, &value); 1049 if (error) 1050 goto restore; 1051 1052 dev_info(ddata->dev, "calibration done: 0x%04x\n", value); 1053 1054 restore: 1055 if (error) 1056 dev_err(ddata->dev, "%s: error %i\n", __func__, error); 1057 1058 error = regmap_update_bits(ddata->reg, CPCAP_REG_CCC1, 1059 0xffff, ccc1); 1060 if (error) 1061 dev_err(ddata->dev, "%s: restore error %i\n", 1062 __func__, error); 1063 1064 return error; 1065 } 1066 1067 #ifdef CONFIG_OF 1068 static const struct of_device_id cpcap_battery_id_table[] = { 1069 { 1070 .compatible = "motorola,cpcap-battery", 1071 }, 1072 {}, 1073 }; 1074 MODULE_DEVICE_TABLE(of, cpcap_battery_id_table); 1075 #endif 1076 1077 static const struct power_supply_desc cpcap_charger_battery_desc = { 1078 .name = "battery", 1079 .type = POWER_SUPPLY_TYPE_BATTERY, 1080 .properties = cpcap_battery_props, 1081 .num_properties = ARRAY_SIZE(cpcap_battery_props), 1082 .get_property = cpcap_battery_get_property, 1083 .set_property = cpcap_battery_set_property, 1084 .property_is_writeable = cpcap_battery_property_is_writeable, 1085 .external_power_changed = cpcap_battery_external_power_changed, 1086 }; 1087 1088 static int cpcap_battery_probe(struct platform_device *pdev) 1089 { 1090 struct cpcap_battery_ddata *ddata; 1091 struct power_supply_config psy_cfg = {}; 1092 int error; 1093 1094 ddata = devm_kzalloc(&pdev->dev, sizeof(*ddata), GFP_KERNEL); 1095 if (!ddata) 1096 return -ENOMEM; 1097 1098 cpcap_battery_detect_battery_type(ddata); 1099 1100 INIT_LIST_HEAD(&ddata->irq_list); 1101 ddata->dev = &pdev->dev; 1102 1103 ddata->reg = dev_get_regmap(ddata->dev->parent, NULL); 1104 if (!ddata->reg) 1105 return -ENODEV; 1106 1107 error = cpcap_get_vendor(ddata->dev, ddata->reg, &ddata->vendor); 1108 if (error) 1109 return error; 1110 1111 switch (ddata->vendor) { 1112 case CPCAP_VENDOR_ST: 1113 ddata->cc_lsb = 95374; /* μAms per LSB */ 1114 break; 1115 case CPCAP_VENDOR_TI: 1116 ddata->cc_lsb = 91501; /* μAms per LSB */ 1117 break; 1118 default: 1119 return -EINVAL; 1120 } 1121 ddata->cc_lsb = (ddata->cc_lsb * ddata->config.cd_factor) / 1000; 1122 1123 platform_set_drvdata(pdev, ddata); 1124 1125 error = cpcap_battery_init_interrupts(pdev, ddata); 1126 if (error) 1127 return error; 1128 1129 error = cpcap_battery_init_iio(ddata); 1130 if (error) 1131 return error; 1132 1133 psy_cfg.of_node = pdev->dev.of_node; 1134 psy_cfg.drv_data = ddata; 1135 1136 ddata->psy = devm_power_supply_register(ddata->dev, 1137 &cpcap_charger_battery_desc, 1138 &psy_cfg); 1139 error = PTR_ERR_OR_ZERO(ddata->psy); 1140 if (error) { 1141 dev_err(ddata->dev, "failed to register power supply\n"); 1142 return error; 1143 } 1144 1145 atomic_set(&ddata->active, 1); 1146 1147 error = cpcap_battery_calibrate(ddata); 1148 if (error) 1149 return error; 1150 1151 return 0; 1152 } 1153 1154 static int cpcap_battery_remove(struct platform_device *pdev) 1155 { 1156 struct cpcap_battery_ddata *ddata = platform_get_drvdata(pdev); 1157 int error; 1158 1159 atomic_set(&ddata->active, 0); 1160 error = regmap_update_bits(ddata->reg, CPCAP_REG_BPEOL, 1161 0xffff, 0); 1162 if (error) 1163 dev_err(&pdev->dev, "could not disable: %i\n", error); 1164 1165 return 0; 1166 } 1167 1168 static struct platform_driver cpcap_battery_driver = { 1169 .driver = { 1170 .name = "cpcap_battery", 1171 .of_match_table = of_match_ptr(cpcap_battery_id_table), 1172 }, 1173 .probe = cpcap_battery_probe, 1174 .remove = cpcap_battery_remove, 1175 }; 1176 module_platform_driver(cpcap_battery_driver); 1177 1178 MODULE_LICENSE("GPL v2"); 1179 MODULE_AUTHOR("Tony Lindgren <tony@atomide.com>"); 1180 MODULE_DESCRIPTION("CPCAP PMIC Battery Driver"); 1181