1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Battery driver for Marvell 88PM860x PMIC 4 * 5 * Copyright (c) 2012 Marvell International Ltd. 6 * Author: Jett Zhou <jtzhou@marvell.com> 7 * Haojian Zhuang <haojian.zhuang@marvell.com> 8 */ 9 10 #include <linux/kernel.h> 11 #include <linux/module.h> 12 #include <linux/platform_device.h> 13 #include <linux/slab.h> 14 #include <linux/mutex.h> 15 #include <linux/string.h> 16 #include <linux/power_supply.h> 17 #include <linux/mfd/88pm860x.h> 18 #include <linux/delay.h> 19 20 /* bit definitions of Status Query Interface 2 */ 21 #define STATUS2_CHG (1 << 2) 22 #define STATUS2_BAT (1 << 3) 23 #define STATUS2_VBUS (1 << 4) 24 25 /* bit definitions of Measurement Enable 1 Register */ 26 #define MEAS1_TINT (1 << 3) 27 #define MEAS1_GP1 (1 << 5) 28 29 /* bit definitions of Measurement Enable 3 Register */ 30 #define MEAS3_IBAT (1 << 0) 31 #define MEAS3_BAT_DET (1 << 1) 32 #define MEAS3_CC (1 << 2) 33 34 /* bit definitions of Measurement Off Time Register */ 35 #define MEAS_OFF_SLEEP_EN (1 << 1) 36 37 /* bit definitions of GPADC Bias Current 2 Register */ 38 #define GPBIAS2_GPADC1_SET (2 << 4) 39 /* GPADC1 Bias Current value in uA unit */ 40 #define GPBIAS2_GPADC1_UA ((GPBIAS2_GPADC1_SET >> 4) * 5 + 1) 41 42 /* bit definitions of GPADC Misc 1 Register */ 43 #define GPMISC1_GPADC_EN (1 << 0) 44 45 /* bit definitions of Charger Control 6 Register */ 46 #define CC6_BAT_DET_GPADC1 1 47 48 /* bit definitions of Coulomb Counter Reading Register */ 49 #define CCNT_AVG_SEL (4 << 3) 50 51 /* bit definitions of RTC miscellaneous Register1 */ 52 #define RTC_SOC_5LSB (0x1F << 3) 53 54 /* bit definitions of RTC Register1 */ 55 #define RTC_SOC_3MSB (0x7) 56 57 /* bit definitions of Power up Log register */ 58 #define BAT_WU_LOG (1<<6) 59 60 /* coulomb counter index */ 61 #define CCNT_POS1 0 62 #define CCNT_POS2 1 63 #define CCNT_NEG1 2 64 #define CCNT_NEG2 3 65 #define CCNT_SPOS 4 66 #define CCNT_SNEG 5 67 68 /* OCV -- Open Circuit Voltage */ 69 #define OCV_MODE_ACTIVE 0 70 #define OCV_MODE_SLEEP 1 71 72 /* Vbat range of CC for measuring Rbat */ 73 #define LOW_BAT_THRESHOLD 3600 74 #define VBATT_RESISTOR_MIN 3800 75 #define VBATT_RESISTOR_MAX 4100 76 77 /* TBAT for batt, TINT for chip itself */ 78 #define PM860X_TEMP_TINT (0) 79 #define PM860X_TEMP_TBAT (1) 80 81 /* 82 * Battery temperature based on NTC resistor, defined 83 * corresponding resistor value -- Ohm / C degeree. 84 */ 85 #define TBAT_NEG_25D 127773 /* -25 */ 86 #define TBAT_NEG_10D 54564 /* -10 */ 87 #define TBAT_0D 32330 /* 0 */ 88 #define TBAT_10D 19785 /* 10 */ 89 #define TBAT_20D 12468 /* 20 */ 90 #define TBAT_30D 8072 /* 30 */ 91 #define TBAT_40D 5356 /* 40 */ 92 93 struct pm860x_battery_info { 94 struct pm860x_chip *chip; 95 struct i2c_client *i2c; 96 struct device *dev; 97 98 struct power_supply *battery; 99 struct mutex lock; 100 int status; 101 int irq_cc; 102 int irq_batt; 103 int max_capacity; 104 int resistor; /* Battery Internal Resistor */ 105 int last_capacity; 106 int start_soc; 107 unsigned present:1; 108 unsigned temp_type:1; /* TINT or TBAT */ 109 }; 110 111 struct ccnt { 112 unsigned long long int pos; 113 unsigned long long int neg; 114 unsigned int spos; 115 unsigned int sneg; 116 117 int total_chg; /* mAh(3.6C) */ 118 int total_dischg; /* mAh(3.6C) */ 119 }; 120 121 /* 122 * State of Charge. 123 * The first number is mAh(=3.6C), and the second number is percent point. 124 */ 125 static int array_soc[][2] = { 126 {4170, 100}, {4154, 99}, {4136, 98}, {4122, 97}, {4107, 96}, 127 {4102, 95}, {4088, 94}, {4081, 93}, {4070, 92}, {4060, 91}, 128 {4053, 90}, {4044, 89}, {4035, 88}, {4028, 87}, {4019, 86}, 129 {4013, 85}, {4006, 84}, {3995, 83}, {3987, 82}, {3982, 81}, 130 {3976, 80}, {3968, 79}, {3962, 78}, {3954, 77}, {3946, 76}, 131 {3941, 75}, {3934, 74}, {3929, 73}, {3922, 72}, {3916, 71}, 132 {3910, 70}, {3904, 69}, {3898, 68}, {3892, 67}, {3887, 66}, 133 {3880, 65}, {3874, 64}, {3868, 63}, {3862, 62}, {3854, 61}, 134 {3849, 60}, {3843, 59}, {3840, 58}, {3833, 57}, {3829, 56}, 135 {3824, 55}, {3818, 54}, {3815, 53}, {3810, 52}, {3808, 51}, 136 {3804, 50}, {3801, 49}, {3798, 48}, {3796, 47}, {3792, 46}, 137 {3789, 45}, {3785, 44}, {3784, 43}, {3782, 42}, {3780, 41}, 138 {3777, 40}, {3776, 39}, {3774, 38}, {3772, 37}, {3771, 36}, 139 {3769, 35}, {3768, 34}, {3764, 33}, {3763, 32}, {3760, 31}, 140 {3760, 30}, {3754, 29}, {3750, 28}, {3749, 27}, {3744, 26}, 141 {3740, 25}, {3734, 24}, {3732, 23}, {3728, 22}, {3726, 21}, 142 {3720, 20}, {3716, 19}, {3709, 18}, {3703, 17}, {3698, 16}, 143 {3692, 15}, {3683, 14}, {3675, 13}, {3670, 12}, {3665, 11}, 144 {3661, 10}, {3649, 9}, {3637, 8}, {3622, 7}, {3609, 6}, 145 {3580, 5}, {3558, 4}, {3540, 3}, {3510, 2}, {3429, 1}, 146 }; 147 148 static struct ccnt ccnt_data; 149 150 /* 151 * register 1 bit[7:0] -- bit[11:4] of measured value of voltage 152 * register 0 bit[3:0] -- bit[3:0] of measured value of voltage 153 */ 154 static int measure_12bit_voltage(struct pm860x_battery_info *info, 155 int offset, int *data) 156 { 157 unsigned char buf[2]; 158 int ret; 159 160 ret = pm860x_bulk_read(info->i2c, offset, 2, buf); 161 if (ret < 0) 162 return ret; 163 164 *data = ((buf[0] & 0xff) << 4) | (buf[1] & 0x0f); 165 /* V_MEAS(mV) = data * 1.8 * 1000 / (2^12) */ 166 *data = ((*data & 0xfff) * 9 * 25) >> 9; 167 return 0; 168 } 169 170 static int measure_vbatt(struct pm860x_battery_info *info, int state, 171 int *data) 172 { 173 unsigned char buf[5]; 174 int ret; 175 176 switch (state) { 177 case OCV_MODE_ACTIVE: 178 ret = measure_12bit_voltage(info, PM8607_VBAT_MEAS1, data); 179 if (ret) 180 return ret; 181 /* V_BATT_MEAS(mV) = value * 3 * 1.8 * 1000 / (2^12) */ 182 *data *= 3; 183 break; 184 case OCV_MODE_SLEEP: 185 /* 186 * voltage value of VBATT in sleep mode is saved in different 187 * registers. 188 * bit[11:10] -- bit[7:6] of LDO9(0x18) 189 * bit[9:8] -- bit[7:6] of LDO8(0x17) 190 * bit[7:6] -- bit[7:6] of LDO7(0x16) 191 * bit[5:4] -- bit[7:6] of LDO6(0x15) 192 * bit[3:0] -- bit[7:4] of LDO5(0x14) 193 */ 194 ret = pm860x_bulk_read(info->i2c, PM8607_LDO5, 5, buf); 195 if (ret < 0) 196 return ret; 197 ret = ((buf[4] >> 6) << 10) | ((buf[3] >> 6) << 8) 198 | ((buf[2] >> 6) << 6) | ((buf[1] >> 6) << 4) 199 | (buf[0] >> 4); 200 /* V_BATT_MEAS(mV) = data * 3 * 1.8 * 1000 / (2^12) */ 201 *data = ((*data & 0xff) * 27 * 25) >> 9; 202 break; 203 default: 204 return -EINVAL; 205 } 206 return 0; 207 } 208 209 /* 210 * Return value is signed data. 211 * Negative value means discharging, and positive value means charging. 212 */ 213 static int measure_current(struct pm860x_battery_info *info, int *data) 214 { 215 unsigned char buf[2]; 216 short s; 217 int ret; 218 219 ret = pm860x_bulk_read(info->i2c, PM8607_IBAT_MEAS1, 2, buf); 220 if (ret < 0) 221 return ret; 222 223 s = ((buf[0] & 0xff) << 8) | (buf[1] & 0xff); 224 /* current(mA) = value * 0.125 */ 225 *data = s >> 3; 226 return 0; 227 } 228 229 static int set_charger_current(struct pm860x_battery_info *info, int data, 230 int *old) 231 { 232 int ret; 233 234 if (data < 50 || data > 1600 || !old) 235 return -EINVAL; 236 237 data = ((data - 50) / 50) & 0x1f; 238 *old = pm860x_reg_read(info->i2c, PM8607_CHG_CTRL2); 239 *old = (*old & 0x1f) * 50 + 50; 240 ret = pm860x_set_bits(info->i2c, PM8607_CHG_CTRL2, 0x1f, data); 241 if (ret < 0) 242 return ret; 243 return 0; 244 } 245 246 static int read_ccnt(struct pm860x_battery_info *info, int offset, 247 int *ccnt) 248 { 249 unsigned char buf[2]; 250 int ret; 251 252 ret = pm860x_set_bits(info->i2c, PM8607_CCNT, 7, offset & 7); 253 if (ret < 0) 254 goto out; 255 ret = pm860x_bulk_read(info->i2c, PM8607_CCNT_MEAS1, 2, buf); 256 if (ret < 0) 257 goto out; 258 *ccnt = ((buf[0] & 0xff) << 8) | (buf[1] & 0xff); 259 return 0; 260 out: 261 return ret; 262 } 263 264 static int calc_ccnt(struct pm860x_battery_info *info, struct ccnt *ccnt) 265 { 266 unsigned int sum; 267 int ret; 268 int data; 269 270 ret = read_ccnt(info, CCNT_POS1, &data); 271 if (ret) 272 goto out; 273 sum = data & 0xffff; 274 ret = read_ccnt(info, CCNT_POS2, &data); 275 if (ret) 276 goto out; 277 sum |= (data & 0xffff) << 16; 278 ccnt->pos += sum; 279 280 ret = read_ccnt(info, CCNT_NEG1, &data); 281 if (ret) 282 goto out; 283 sum = data & 0xffff; 284 ret = read_ccnt(info, CCNT_NEG2, &data); 285 if (ret) 286 goto out; 287 sum |= (data & 0xffff) << 16; 288 sum = ~sum + 1; /* since it's negative */ 289 ccnt->neg += sum; 290 291 ret = read_ccnt(info, CCNT_SPOS, &data); 292 if (ret) 293 goto out; 294 ccnt->spos += data; 295 ret = read_ccnt(info, CCNT_SNEG, &data); 296 if (ret) 297 goto out; 298 299 /* 300 * charge(mAh) = count * 1.6984 * 1e(-8) 301 * = count * 16984 * 1.024 * 1.024 * 1.024 / (2 ^ 40) 302 * = count * 18236 / (2 ^ 40) 303 */ 304 ccnt->total_chg = (int) ((ccnt->pos * 18236) >> 40); 305 ccnt->total_dischg = (int) ((ccnt->neg * 18236) >> 40); 306 return 0; 307 out: 308 return ret; 309 } 310 311 static int clear_ccnt(struct pm860x_battery_info *info, struct ccnt *ccnt) 312 { 313 int data; 314 315 memset(ccnt, 0, sizeof(*ccnt)); 316 /* read to clear ccnt */ 317 read_ccnt(info, CCNT_POS1, &data); 318 read_ccnt(info, CCNT_POS2, &data); 319 read_ccnt(info, CCNT_NEG1, &data); 320 read_ccnt(info, CCNT_NEG2, &data); 321 read_ccnt(info, CCNT_SPOS, &data); 322 read_ccnt(info, CCNT_SNEG, &data); 323 return 0; 324 } 325 326 /* Calculate Open Circuit Voltage */ 327 static int calc_ocv(struct pm860x_battery_info *info, int *ocv) 328 { 329 int ret; 330 int i; 331 int data; 332 int vbatt_avg; 333 int vbatt_sum; 334 int ibatt_avg; 335 int ibatt_sum; 336 337 if (!ocv) 338 return -EINVAL; 339 340 for (i = 0, ibatt_sum = 0, vbatt_sum = 0; i < 10; i++) { 341 ret = measure_vbatt(info, OCV_MODE_ACTIVE, &data); 342 if (ret) 343 goto out; 344 vbatt_sum += data; 345 ret = measure_current(info, &data); 346 if (ret) 347 goto out; 348 ibatt_sum += data; 349 } 350 vbatt_avg = vbatt_sum / 10; 351 ibatt_avg = ibatt_sum / 10; 352 353 mutex_lock(&info->lock); 354 if (info->present) 355 *ocv = vbatt_avg - ibatt_avg * info->resistor / 1000; 356 else 357 *ocv = vbatt_avg; 358 mutex_unlock(&info->lock); 359 dev_dbg(info->dev, "VBAT average:%d, OCV:%d\n", vbatt_avg, *ocv); 360 return 0; 361 out: 362 return ret; 363 } 364 365 /* Calculate State of Charge (percent points) */ 366 static int calc_soc(struct pm860x_battery_info *info, int state, int *soc) 367 { 368 int i; 369 int ocv; 370 int count; 371 int ret = -EINVAL; 372 373 if (!soc) 374 return -EINVAL; 375 376 switch (state) { 377 case OCV_MODE_ACTIVE: 378 ret = calc_ocv(info, &ocv); 379 break; 380 case OCV_MODE_SLEEP: 381 ret = measure_vbatt(info, OCV_MODE_SLEEP, &ocv); 382 break; 383 } 384 if (ret) 385 return ret; 386 387 count = ARRAY_SIZE(array_soc); 388 if (ocv < array_soc[count - 1][0]) { 389 *soc = 0; 390 return 0; 391 } 392 393 for (i = 0; i < count; i++) { 394 if (ocv >= array_soc[i][0]) { 395 *soc = array_soc[i][1]; 396 break; 397 } 398 } 399 return 0; 400 } 401 402 static irqreturn_t pm860x_coulomb_handler(int irq, void *data) 403 { 404 struct pm860x_battery_info *info = data; 405 406 calc_ccnt(info, &ccnt_data); 407 return IRQ_HANDLED; 408 } 409 410 static irqreturn_t pm860x_batt_handler(int irq, void *data) 411 { 412 struct pm860x_battery_info *info = data; 413 int ret; 414 415 mutex_lock(&info->lock); 416 ret = pm860x_reg_read(info->i2c, PM8607_STATUS_2); 417 if (ret & STATUS2_BAT) { 418 info->present = 1; 419 info->temp_type = PM860X_TEMP_TBAT; 420 } else { 421 info->present = 0; 422 info->temp_type = PM860X_TEMP_TINT; 423 } 424 mutex_unlock(&info->lock); 425 /* clear ccnt since battery is attached or dettached */ 426 clear_ccnt(info, &ccnt_data); 427 return IRQ_HANDLED; 428 } 429 430 static void pm860x_init_battery(struct pm860x_battery_info *info) 431 { 432 unsigned char buf[2]; 433 int ret; 434 int data; 435 int bat_remove; 436 int soc = 0; 437 438 /* measure enable on GPADC1 */ 439 data = MEAS1_GP1; 440 if (info->temp_type == PM860X_TEMP_TINT) 441 data |= MEAS1_TINT; 442 ret = pm860x_set_bits(info->i2c, PM8607_MEAS_EN1, data, data); 443 if (ret) 444 goto out; 445 446 /* measure enable on IBAT, BAT_DET, CC. IBAT is depend on CC. */ 447 data = MEAS3_IBAT | MEAS3_BAT_DET | MEAS3_CC; 448 ret = pm860x_set_bits(info->i2c, PM8607_MEAS_EN3, data, data); 449 if (ret) 450 goto out; 451 452 /* measure disable CC in sleep time */ 453 ret = pm860x_reg_write(info->i2c, PM8607_MEAS_OFF_TIME1, 0x82); 454 if (ret) 455 goto out; 456 ret = pm860x_reg_write(info->i2c, PM8607_MEAS_OFF_TIME2, 0x6c); 457 if (ret) 458 goto out; 459 460 /* enable GPADC */ 461 ret = pm860x_set_bits(info->i2c, PM8607_GPADC_MISC1, 462 GPMISC1_GPADC_EN, GPMISC1_GPADC_EN); 463 if (ret < 0) 464 goto out; 465 466 /* detect battery via GPADC1 */ 467 ret = pm860x_set_bits(info->i2c, PM8607_CHG_CTRL6, 468 CC6_BAT_DET_GPADC1, CC6_BAT_DET_GPADC1); 469 if (ret < 0) 470 goto out; 471 472 ret = pm860x_set_bits(info->i2c, PM8607_CCNT, 7 << 3, 473 CCNT_AVG_SEL); 474 if (ret < 0) 475 goto out; 476 477 /* set GPADC1 bias */ 478 ret = pm860x_set_bits(info->i2c, PM8607_GP_BIAS2, 0xF << 4, 479 GPBIAS2_GPADC1_SET); 480 if (ret < 0) 481 goto out; 482 483 /* check whether battery present) */ 484 mutex_lock(&info->lock); 485 ret = pm860x_reg_read(info->i2c, PM8607_STATUS_2); 486 if (ret < 0) { 487 mutex_unlock(&info->lock); 488 goto out; 489 } 490 if (ret & STATUS2_BAT) { 491 info->present = 1; 492 info->temp_type = PM860X_TEMP_TBAT; 493 } else { 494 info->present = 0; 495 info->temp_type = PM860X_TEMP_TINT; 496 } 497 mutex_unlock(&info->lock); 498 499 ret = calc_soc(info, OCV_MODE_ACTIVE, &soc); 500 if (ret < 0) 501 goto out; 502 503 data = pm860x_reg_read(info->i2c, PM8607_POWER_UP_LOG); 504 bat_remove = data & BAT_WU_LOG; 505 506 dev_dbg(info->dev, "battery wake up? %s\n", 507 bat_remove != 0 ? "yes" : "no"); 508 509 /* restore SOC from RTC domain register */ 510 if (bat_remove == 0) { 511 buf[0] = pm860x_reg_read(info->i2c, PM8607_RTC_MISC2); 512 buf[1] = pm860x_reg_read(info->i2c, PM8607_RTC1); 513 data = ((buf[1] & 0x3) << 5) | ((buf[0] >> 3) & 0x1F); 514 if (data > soc + 15) 515 info->start_soc = soc; 516 else if (data < soc - 15) 517 info->start_soc = soc; 518 else 519 info->start_soc = data; 520 dev_dbg(info->dev, "soc_rtc %d, soc_ocv :%d\n", data, soc); 521 } else { 522 pm860x_set_bits(info->i2c, PM8607_POWER_UP_LOG, 523 BAT_WU_LOG, BAT_WU_LOG); 524 info->start_soc = soc; 525 } 526 info->last_capacity = info->start_soc; 527 dev_dbg(info->dev, "init soc : %d\n", info->last_capacity); 528 out: 529 return; 530 } 531 532 static void set_temp_threshold(struct pm860x_battery_info *info, 533 int min, int max) 534 { 535 int data; 536 537 /* (tmp << 8) / 1800 */ 538 if (min <= 0) 539 data = 0; 540 else 541 data = (min << 8) / 1800; 542 pm860x_reg_write(info->i2c, PM8607_GPADC1_HIGHTH, data); 543 dev_dbg(info->dev, "TEMP_HIGHTH : min: %d, 0x%x\n", min, data); 544 545 if (max <= 0) 546 data = 0xff; 547 else 548 data = (max << 8) / 1800; 549 pm860x_reg_write(info->i2c, PM8607_GPADC1_LOWTH, data); 550 dev_dbg(info->dev, "TEMP_LOWTH:max : %d, 0x%x\n", max, data); 551 } 552 553 static int measure_temp(struct pm860x_battery_info *info, int *data) 554 { 555 int ret; 556 int temp; 557 int min; 558 int max; 559 560 if (info->temp_type == PM860X_TEMP_TINT) { 561 ret = measure_12bit_voltage(info, PM8607_TINT_MEAS1, data); 562 if (ret) 563 return ret; 564 *data = (*data - 884) * 1000 / 3611; 565 } else { 566 ret = measure_12bit_voltage(info, PM8607_GPADC1_MEAS1, data); 567 if (ret) 568 return ret; 569 /* meausered Vtbat(mV) / Ibias_current(11uA)*/ 570 *data = (*data * 1000) / GPBIAS2_GPADC1_UA; 571 572 if (*data > TBAT_NEG_25D) { 573 temp = -30; /* over cold , suppose -30 roughly */ 574 max = TBAT_NEG_10D * GPBIAS2_GPADC1_UA / 1000; 575 set_temp_threshold(info, 0, max); 576 } else if (*data > TBAT_NEG_10D) { 577 temp = -15; /* -15 degree, code */ 578 max = TBAT_NEG_10D * GPBIAS2_GPADC1_UA / 1000; 579 set_temp_threshold(info, 0, max); 580 } else if (*data > TBAT_0D) { 581 temp = -5; /* -5 degree */ 582 min = TBAT_NEG_10D * GPBIAS2_GPADC1_UA / 1000; 583 max = TBAT_40D * GPBIAS2_GPADC1_UA / 1000; 584 set_temp_threshold(info, min, max); 585 } else if (*data > TBAT_10D) { 586 temp = 5; /* in range of (0, 10) */ 587 min = TBAT_NEG_10D * GPBIAS2_GPADC1_UA / 1000; 588 max = TBAT_40D * GPBIAS2_GPADC1_UA / 1000; 589 set_temp_threshold(info, min, max); 590 } else if (*data > TBAT_20D) { 591 temp = 15; /* in range of (10, 20) */ 592 min = TBAT_NEG_10D * GPBIAS2_GPADC1_UA / 1000; 593 max = TBAT_40D * GPBIAS2_GPADC1_UA / 1000; 594 set_temp_threshold(info, min, max); 595 } else if (*data > TBAT_30D) { 596 temp = 25; /* in range of (20, 30) */ 597 min = TBAT_NEG_10D * GPBIAS2_GPADC1_UA / 1000; 598 max = TBAT_40D * GPBIAS2_GPADC1_UA / 1000; 599 set_temp_threshold(info, min, max); 600 } else if (*data > TBAT_40D) { 601 temp = 35; /* in range of (30, 40) */ 602 min = TBAT_NEG_10D * GPBIAS2_GPADC1_UA / 1000; 603 max = TBAT_40D * GPBIAS2_GPADC1_UA / 1000; 604 set_temp_threshold(info, min, max); 605 } else { 606 min = TBAT_40D * GPBIAS2_GPADC1_UA / 1000; 607 set_temp_threshold(info, min, 0); 608 temp = 45; /* over heat ,suppose 45 roughly */ 609 } 610 611 dev_dbg(info->dev, "temp_C:%d C,temp_mv:%d mv\n", temp, *data); 612 *data = temp; 613 } 614 return 0; 615 } 616 617 static int calc_resistor(struct pm860x_battery_info *info) 618 { 619 int vbatt_sum1; 620 int vbatt_sum2; 621 int chg_current; 622 int ibatt_sum1; 623 int ibatt_sum2; 624 int data; 625 int ret; 626 int i; 627 628 ret = measure_current(info, &data); 629 /* make sure that charging is launched by data > 0 */ 630 if (ret || data < 0) 631 goto out; 632 633 ret = measure_vbatt(info, OCV_MODE_ACTIVE, &data); 634 if (ret) 635 goto out; 636 /* calculate resistor only in CC charge mode */ 637 if (data < VBATT_RESISTOR_MIN || data > VBATT_RESISTOR_MAX) 638 goto out; 639 640 /* current is saved */ 641 if (set_charger_current(info, 500, &chg_current)) 642 goto out; 643 644 /* 645 * set charge current as 500mA, wait about 500ms till charging 646 * process is launched and stable with the newer charging current. 647 */ 648 msleep(500); 649 650 for (i = 0, vbatt_sum1 = 0, ibatt_sum1 = 0; i < 10; i++) { 651 ret = measure_vbatt(info, OCV_MODE_ACTIVE, &data); 652 if (ret) 653 goto out_meas; 654 vbatt_sum1 += data; 655 ret = measure_current(info, &data); 656 if (ret) 657 goto out_meas; 658 659 if (data < 0) 660 ibatt_sum1 = ibatt_sum1 - data; /* discharging */ 661 else 662 ibatt_sum1 = ibatt_sum1 + data; /* charging */ 663 } 664 665 if (set_charger_current(info, 100, &ret)) 666 goto out_meas; 667 /* 668 * set charge current as 100mA, wait about 500ms till charging 669 * process is launched and stable with the newer charging current. 670 */ 671 msleep(500); 672 673 for (i = 0, vbatt_sum2 = 0, ibatt_sum2 = 0; i < 10; i++) { 674 ret = measure_vbatt(info, OCV_MODE_ACTIVE, &data); 675 if (ret) 676 goto out_meas; 677 vbatt_sum2 += data; 678 ret = measure_current(info, &data); 679 if (ret) 680 goto out_meas; 681 682 if (data < 0) 683 ibatt_sum2 = ibatt_sum2 - data; /* discharging */ 684 else 685 ibatt_sum2 = ibatt_sum2 + data; /* charging */ 686 } 687 688 /* restore current setting */ 689 if (set_charger_current(info, chg_current, &ret)) 690 goto out_meas; 691 692 if ((vbatt_sum1 > vbatt_sum2) && (ibatt_sum1 > ibatt_sum2) && 693 (ibatt_sum2 > 0)) { 694 /* calculate resistor in discharging case */ 695 data = 1000 * (vbatt_sum1 - vbatt_sum2) 696 / (ibatt_sum1 - ibatt_sum2); 697 if ((data - info->resistor > 0) && 698 (data - info->resistor < info->resistor)) 699 info->resistor = data; 700 if ((info->resistor - data > 0) && 701 (info->resistor - data < data)) 702 info->resistor = data; 703 } 704 return 0; 705 706 out_meas: 707 set_charger_current(info, chg_current, &ret); 708 out: 709 return -EINVAL; 710 } 711 712 static int calc_capacity(struct pm860x_battery_info *info, int *cap) 713 { 714 int ret; 715 int data; 716 int ibat; 717 int cap_ocv = 0; 718 int cap_cc = 0; 719 720 ret = calc_ccnt(info, &ccnt_data); 721 if (ret) 722 goto out; 723 soc: 724 data = info->max_capacity * info->start_soc / 100; 725 if (ccnt_data.total_dischg - ccnt_data.total_chg <= data) { 726 cap_cc = 727 data + ccnt_data.total_chg - ccnt_data.total_dischg; 728 } else { 729 clear_ccnt(info, &ccnt_data); 730 calc_soc(info, OCV_MODE_ACTIVE, &info->start_soc); 731 dev_dbg(info->dev, "restart soc = %d !\n", 732 info->start_soc); 733 goto soc; 734 } 735 736 cap_cc = cap_cc * 100 / info->max_capacity; 737 if (cap_cc < 0) 738 cap_cc = 0; 739 else if (cap_cc > 100) 740 cap_cc = 100; 741 742 dev_dbg(info->dev, "%s, last cap : %d", __func__, 743 info->last_capacity); 744 745 ret = measure_current(info, &ibat); 746 if (ret) 747 goto out; 748 /* Calculate the capacity when discharging(ibat < 0) */ 749 if (ibat < 0) { 750 ret = calc_soc(info, OCV_MODE_ACTIVE, &cap_ocv); 751 if (ret) 752 cap_ocv = info->last_capacity; 753 ret = measure_vbatt(info, OCV_MODE_ACTIVE, &data); 754 if (ret) 755 goto out; 756 if (data <= LOW_BAT_THRESHOLD) { 757 /* choose the lower capacity value to report 758 * between vbat and CC when vbat < 3.6v; 759 * than 3.6v; 760 */ 761 *cap = min(cap_ocv, cap_cc); 762 } else { 763 /* when detect vbat > 3.6v, but cap_cc < 15,and 764 * cap_ocv is 10% larger than cap_cc, we can think 765 * CC have some accumulation error, switch to OCV 766 * to estimate capacity; 767 * */ 768 if (cap_cc < 15 && cap_ocv - cap_cc > 10) 769 *cap = cap_ocv; 770 else 771 *cap = cap_cc; 772 } 773 /* when discharging, make sure current capacity 774 * is lower than last*/ 775 if (*cap > info->last_capacity) 776 *cap = info->last_capacity; 777 } else { 778 *cap = cap_cc; 779 } 780 info->last_capacity = *cap; 781 782 dev_dbg(info->dev, "%s, cap_ocv:%d cap_cc:%d, cap:%d\n", 783 (ibat < 0) ? "discharging" : "charging", 784 cap_ocv, cap_cc, *cap); 785 /* 786 * store the current capacity to RTC domain register, 787 * after next power up , it will be restored. 788 */ 789 pm860x_set_bits(info->i2c, PM8607_RTC_MISC2, RTC_SOC_5LSB, 790 (*cap & 0x1F) << 3); 791 pm860x_set_bits(info->i2c, PM8607_RTC1, RTC_SOC_3MSB, 792 ((*cap >> 5) & 0x3)); 793 return 0; 794 out: 795 return ret; 796 } 797 798 static void pm860x_external_power_changed(struct power_supply *psy) 799 { 800 struct pm860x_battery_info *info = dev_get_drvdata(psy->dev.parent); 801 802 calc_resistor(info); 803 } 804 805 static int pm860x_batt_get_prop(struct power_supply *psy, 806 enum power_supply_property psp, 807 union power_supply_propval *val) 808 { 809 struct pm860x_battery_info *info = dev_get_drvdata(psy->dev.parent); 810 int data; 811 int ret; 812 813 switch (psp) { 814 case POWER_SUPPLY_PROP_PRESENT: 815 val->intval = info->present; 816 break; 817 case POWER_SUPPLY_PROP_CAPACITY: 818 ret = calc_capacity(info, &data); 819 if (ret) 820 return ret; 821 if (data < 0) 822 data = 0; 823 else if (data > 100) 824 data = 100; 825 /* return 100 if battery is not attached */ 826 if (!info->present) 827 data = 100; 828 val->intval = data; 829 break; 830 case POWER_SUPPLY_PROP_TECHNOLOGY: 831 val->intval = POWER_SUPPLY_TECHNOLOGY_LION; 832 break; 833 case POWER_SUPPLY_PROP_VOLTAGE_NOW: 834 /* return real vbatt Voltage */ 835 ret = measure_vbatt(info, OCV_MODE_ACTIVE, &data); 836 if (ret) 837 return ret; 838 val->intval = data * 1000; 839 break; 840 case POWER_SUPPLY_PROP_VOLTAGE_AVG: 841 /* return Open Circuit Voltage (not measured voltage) */ 842 ret = calc_ocv(info, &data); 843 if (ret) 844 return ret; 845 val->intval = data * 1000; 846 break; 847 case POWER_SUPPLY_PROP_CURRENT_NOW: 848 ret = measure_current(info, &data); 849 if (ret) 850 return ret; 851 val->intval = data; 852 break; 853 case POWER_SUPPLY_PROP_TEMP: 854 if (info->present) { 855 ret = measure_temp(info, &data); 856 if (ret) 857 return ret; 858 data *= 10; 859 } else { 860 /* Fake Temp 25C Without Battery */ 861 data = 250; 862 } 863 val->intval = data; 864 break; 865 default: 866 return -ENODEV; 867 } 868 return 0; 869 } 870 871 static int pm860x_batt_set_prop(struct power_supply *psy, 872 enum power_supply_property psp, 873 const union power_supply_propval *val) 874 { 875 struct pm860x_battery_info *info = dev_get_drvdata(psy->dev.parent); 876 877 switch (psp) { 878 case POWER_SUPPLY_PROP_CHARGE_FULL: 879 clear_ccnt(info, &ccnt_data); 880 info->start_soc = 100; 881 dev_dbg(info->dev, "chg done, update soc = %d\n", 882 info->start_soc); 883 break; 884 default: 885 return -EPERM; 886 } 887 888 return 0; 889 } 890 891 892 static enum power_supply_property pm860x_batt_props[] = { 893 POWER_SUPPLY_PROP_PRESENT, 894 POWER_SUPPLY_PROP_CAPACITY, 895 POWER_SUPPLY_PROP_TECHNOLOGY, 896 POWER_SUPPLY_PROP_VOLTAGE_NOW, 897 POWER_SUPPLY_PROP_VOLTAGE_AVG, 898 POWER_SUPPLY_PROP_CURRENT_NOW, 899 POWER_SUPPLY_PROP_TEMP, 900 }; 901 902 static const struct power_supply_desc pm860x_battery_desc = { 903 .name = "battery-monitor", 904 .type = POWER_SUPPLY_TYPE_BATTERY, 905 .properties = pm860x_batt_props, 906 .num_properties = ARRAY_SIZE(pm860x_batt_props), 907 .get_property = pm860x_batt_get_prop, 908 .set_property = pm860x_batt_set_prop, 909 .external_power_changed = pm860x_external_power_changed, 910 }; 911 912 static int pm860x_battery_probe(struct platform_device *pdev) 913 { 914 struct pm860x_chip *chip = dev_get_drvdata(pdev->dev.parent); 915 struct pm860x_battery_info *info; 916 struct pm860x_power_pdata *pdata; 917 int ret; 918 919 info = devm_kzalloc(&pdev->dev, sizeof(*info), GFP_KERNEL); 920 if (!info) 921 return -ENOMEM; 922 923 info->irq_cc = platform_get_irq(pdev, 0); 924 if (info->irq_cc <= 0) 925 return -EINVAL; 926 927 info->irq_batt = platform_get_irq(pdev, 1); 928 if (info->irq_batt <= 0) 929 return -EINVAL; 930 931 info->chip = chip; 932 info->i2c = 933 (chip->id == CHIP_PM8607) ? chip->client : chip->companion; 934 info->dev = &pdev->dev; 935 info->status = POWER_SUPPLY_STATUS_UNKNOWN; 936 pdata = pdev->dev.platform_data; 937 938 mutex_init(&info->lock); 939 platform_set_drvdata(pdev, info); 940 941 pm860x_init_battery(info); 942 943 if (pdata && pdata->max_capacity) 944 info->max_capacity = pdata->max_capacity; 945 else 946 info->max_capacity = 1500; /* set default capacity */ 947 if (pdata && pdata->resistor) 948 info->resistor = pdata->resistor; 949 else 950 info->resistor = 300; /* set default internal resistor */ 951 952 info->battery = devm_power_supply_register(&pdev->dev, 953 &pm860x_battery_desc, 954 NULL); 955 if (IS_ERR(info->battery)) 956 return PTR_ERR(info->battery); 957 info->battery->dev.parent = &pdev->dev; 958 959 ret = devm_request_threaded_irq(chip->dev, info->irq_cc, NULL, 960 pm860x_coulomb_handler, IRQF_ONESHOT, 961 "coulomb", info); 962 if (ret < 0) { 963 dev_err(chip->dev, "Failed to request IRQ: #%d: %d\n", 964 info->irq_cc, ret); 965 return ret; 966 } 967 968 ret = devm_request_threaded_irq(chip->dev, info->irq_batt, NULL, 969 pm860x_batt_handler, 970 IRQF_ONESHOT, "battery", info); 971 if (ret < 0) { 972 dev_err(chip->dev, "Failed to request IRQ: #%d: %d\n", 973 info->irq_batt, ret); 974 return ret; 975 } 976 977 978 return 0; 979 } 980 981 #ifdef CONFIG_PM_SLEEP 982 static int pm860x_battery_suspend(struct device *dev) 983 { 984 struct platform_device *pdev = to_platform_device(dev); 985 struct pm860x_chip *chip = dev_get_drvdata(pdev->dev.parent); 986 987 if (device_may_wakeup(dev)) 988 chip->wakeup_flag |= 1 << PM8607_IRQ_CC; 989 return 0; 990 } 991 992 static int pm860x_battery_resume(struct device *dev) 993 { 994 struct platform_device *pdev = to_platform_device(dev); 995 struct pm860x_chip *chip = dev_get_drvdata(pdev->dev.parent); 996 997 if (device_may_wakeup(dev)) 998 chip->wakeup_flag &= ~(1 << PM8607_IRQ_CC); 999 return 0; 1000 } 1001 #endif 1002 1003 static SIMPLE_DEV_PM_OPS(pm860x_battery_pm_ops, 1004 pm860x_battery_suspend, pm860x_battery_resume); 1005 1006 static struct platform_driver pm860x_battery_driver = { 1007 .driver = { 1008 .name = "88pm860x-battery", 1009 .pm = &pm860x_battery_pm_ops, 1010 }, 1011 .probe = pm860x_battery_probe, 1012 }; 1013 module_platform_driver(pm860x_battery_driver); 1014 1015 MODULE_DESCRIPTION("Marvell 88PM860x Battery driver"); 1016 MODULE_LICENSE("GPL"); 1017