1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * UART interface for ChromeOS Embedded Controller 4 * 5 * Copyright 2020-2022 Google LLC. 6 */ 7 8 #include <linux/acpi.h> 9 #include <linux/delay.h> 10 #include <linux/errno.h> 11 #include <linux/init.h> 12 #include <linux/kernel.h> 13 #include <linux/module.h> 14 #include <linux/of.h> 15 #include <linux/platform_data/cros_ec_proto.h> 16 #include <linux/serdev.h> 17 #include <linux/slab.h> 18 #include <uapi/linux/sched/types.h> 19 20 #include "cros_ec.h" 21 22 /* 23 * EC sends contiguous bytes of response packet on UART AP RX. 24 * TTY driver in AP accumulates incoming bytes and calls the registered callback 25 * function. Byte count can range from 1 to MAX bytes supported by EC. 26 * This driver should wait for long time for all callbacks to be processed. 27 * Considering the worst case scenario, wait for 500 msec. This timeout should 28 * account for max latency and some additional guard time. 29 * Best case: Entire packet is received in ~200 ms, wait queue will be released 30 * and packet will be processed. 31 * Worst case: TTY driver sends bytes in multiple callbacks. In this case this 32 * driver will wait for ~1 sec beyond which it will timeout. 33 * This timeout value should not exceed ~500 msec because in case if 34 * EC_CMD_REBOOT_EC sent, high level driver should be able to intercept EC 35 * in RO. 36 */ 37 #define EC_MSG_DEADLINE_MS 500 38 39 /** 40 * struct response_info - Encapsulate EC response related 41 * information for passing between function 42 * cros_ec_uart_pkt_xfer() and cros_ec_uart_rx_bytes() 43 * callback. 44 * @data: Copy the data received from EC here. 45 * @max_size: Max size allocated for the @data buffer. If the 46 * received data exceeds this value, we log an error. 47 * @size: Actual size of data received from EC. This is also 48 * used to accumulate byte count with response is received 49 * in dma chunks. 50 * @exp_len: Expected bytes of response from EC including header. 51 * @status: Re-init to 0 before sending a cmd. Updated to 1 when 52 * a response is successfully received, or an error number 53 * on failure. 54 * @wait_queue: Wait queue EC response where the cros_ec sends request 55 * to EC and waits 56 */ 57 struct response_info { 58 void *data; 59 size_t max_size; 60 size_t size; 61 size_t exp_len; 62 int status; 63 wait_queue_head_t wait_queue; 64 }; 65 66 /** 67 * struct cros_ec_uart - information about a uart-connected EC 68 * 69 * @serdev: serdev uart device we are connected to. 70 * @baudrate: UART baudrate of attached EC device. 71 * @flowcontrol: UART flowcontrol of attached device. 72 * @irq: Linux IRQ number of associated serial device. 73 * @response: Response info passing between cros_ec_uart_pkt_xfer() 74 * and cros_ec_uart_rx_bytes() 75 */ 76 struct cros_ec_uart { 77 struct serdev_device *serdev; 78 u32 baudrate; 79 u8 flowcontrol; 80 u32 irq; 81 struct response_info response; 82 }; 83 84 static int cros_ec_uart_rx_bytes(struct serdev_device *serdev, 85 const u8 *data, 86 size_t count) 87 { 88 struct ec_host_response *host_response; 89 struct cros_ec_device *ec_dev = serdev_device_get_drvdata(serdev); 90 struct cros_ec_uart *ec_uart = ec_dev->priv; 91 struct response_info *resp = &ec_uart->response; 92 93 /* Check if bytes were sent out of band */ 94 if (!resp->data) { 95 /* Discard all bytes */ 96 dev_warn(ec_dev->dev, "Bytes received out of band, dropping them.\n"); 97 return count; 98 } 99 100 /* 101 * Check if incoming bytes + resp->size is greater than allocated 102 * buffer in din by cros_ec. This will ensure that if EC sends more 103 * bytes than max_size, waiting process will be notified with an error. 104 */ 105 if (resp->size + count > resp->max_size) { 106 resp->status = -EMSGSIZE; 107 wake_up(&resp->wait_queue); 108 return count; 109 } 110 111 memcpy(resp->data + resp->size, data, count); 112 113 resp->size += count; 114 115 /* Read data_len if we received response header and if exp_len was not read before. */ 116 if (resp->size >= sizeof(*host_response) && resp->exp_len == 0) { 117 host_response = (struct ec_host_response *)resp->data; 118 resp->exp_len = host_response->data_len + sizeof(*host_response); 119 } 120 121 /* If driver received response header and payload from EC, wake up the wait queue. */ 122 if (resp->size >= sizeof(*host_response) && resp->size == resp->exp_len) { 123 resp->status = 1; 124 wake_up(&resp->wait_queue); 125 } 126 127 return count; 128 } 129 130 static int cros_ec_uart_pkt_xfer(struct cros_ec_device *ec_dev, 131 struct cros_ec_command *ec_msg) 132 { 133 struct cros_ec_uart *ec_uart = ec_dev->priv; 134 struct serdev_device *serdev = ec_uart->serdev; 135 struct response_info *resp = &ec_uart->response; 136 struct ec_host_response *host_response; 137 unsigned int len; 138 int ret, i; 139 u8 sum; 140 141 len = cros_ec_prepare_tx(ec_dev, ec_msg); 142 dev_dbg(ec_dev->dev, "Prepared len=%d\n", len); 143 144 /* Setup for incoming response */ 145 resp->data = ec_dev->din; 146 resp->max_size = ec_dev->din_size; 147 resp->size = 0; 148 resp->exp_len = 0; 149 resp->status = 0; 150 151 ret = serdev_device_write_buf(serdev, ec_dev->dout, len); 152 if (ret < 0 || ret < len) { 153 dev_err(ec_dev->dev, "Unable to write data\n"); 154 if (ret >= 0) 155 ret = -EIO; 156 goto exit; 157 } 158 159 ret = wait_event_timeout(resp->wait_queue, resp->status, 160 msecs_to_jiffies(EC_MSG_DEADLINE_MS)); 161 if (ret == 0) { 162 dev_warn(ec_dev->dev, "Timed out waiting for response.\n"); 163 ret = -ETIMEDOUT; 164 goto exit; 165 } 166 167 if (resp->status < 0) { 168 ret = resp->status; 169 dev_warn(ec_dev->dev, "Error response received: %d\n", ret); 170 goto exit; 171 } 172 173 host_response = (struct ec_host_response *)ec_dev->din; 174 ec_msg->result = host_response->result; 175 176 if (host_response->data_len > ec_msg->insize) { 177 dev_err(ec_dev->dev, "Resp too long (%d bytes, expected %d)\n", 178 host_response->data_len, ec_msg->insize); 179 ret = -ENOSPC; 180 goto exit; 181 } 182 183 /* Validate checksum */ 184 sum = 0; 185 for (i = 0; i < sizeof(*host_response) + host_response->data_len; i++) 186 sum += ec_dev->din[i]; 187 188 if (sum) { 189 dev_err(ec_dev->dev, "Bad packet checksum calculated %x\n", sum); 190 ret = -EBADMSG; 191 goto exit; 192 } 193 194 memcpy(ec_msg->data, ec_dev->din + sizeof(*host_response), host_response->data_len); 195 196 ret = host_response->data_len; 197 198 exit: 199 /* Invalidate response buffer to guard against out of band rx data */ 200 resp->data = NULL; 201 202 if (ec_msg->command == EC_CMD_REBOOT_EC) 203 msleep(EC_REBOOT_DELAY_MS); 204 205 return ret; 206 } 207 208 static int cros_ec_uart_resource(struct acpi_resource *ares, void *data) 209 { 210 struct cros_ec_uart *ec_uart = data; 211 struct acpi_resource_uart_serialbus *sb = &ares->data.uart_serial_bus; 212 213 if (ares->type == ACPI_RESOURCE_TYPE_SERIAL_BUS && 214 sb->type == ACPI_RESOURCE_SERIAL_TYPE_UART) { 215 ec_uart->baudrate = sb->default_baud_rate; 216 dev_dbg(&ec_uart->serdev->dev, "Baudrate %d\n", ec_uart->baudrate); 217 218 ec_uart->flowcontrol = sb->flow_control; 219 dev_dbg(&ec_uart->serdev->dev, "Flow control %d\n", ec_uart->flowcontrol); 220 } 221 222 return 0; 223 } 224 225 static int cros_ec_uart_acpi_probe(struct cros_ec_uart *ec_uart) 226 { 227 int ret; 228 LIST_HEAD(resources); 229 struct acpi_device *adev = ACPI_COMPANION(&ec_uart->serdev->dev); 230 231 ret = acpi_dev_get_resources(adev, &resources, cros_ec_uart_resource, ec_uart); 232 if (ret < 0) 233 return ret; 234 235 acpi_dev_free_resource_list(&resources); 236 237 /* Retrieve GpioInt and translate it to Linux IRQ number */ 238 ret = acpi_dev_gpio_irq_get(adev, 0); 239 if (ret < 0) 240 return ret; 241 242 ec_uart->irq = ret; 243 dev_dbg(&ec_uart->serdev->dev, "IRQ number %d\n", ec_uart->irq); 244 245 return 0; 246 } 247 248 static const struct serdev_device_ops cros_ec_uart_client_ops = { 249 .receive_buf = cros_ec_uart_rx_bytes, 250 }; 251 252 static int cros_ec_uart_probe(struct serdev_device *serdev) 253 { 254 struct device *dev = &serdev->dev; 255 struct cros_ec_device *ec_dev; 256 struct cros_ec_uart *ec_uart; 257 int ret; 258 259 ec_uart = devm_kzalloc(dev, sizeof(*ec_uart), GFP_KERNEL); 260 if (!ec_uart) 261 return -ENOMEM; 262 263 ec_dev = devm_kzalloc(dev, sizeof(*ec_dev), GFP_KERNEL); 264 if (!ec_dev) 265 return -ENOMEM; 266 267 serdev_device_set_drvdata(serdev, ec_dev); 268 init_waitqueue_head(&ec_uart->response.wait_queue); 269 270 ec_uart->serdev = serdev; 271 272 ret = cros_ec_uart_acpi_probe(ec_uart); 273 if (ret < 0) { 274 dev_err(dev, "Failed to get ACPI info (%d)", ret); 275 return ret; 276 } 277 278 /* Initialize ec_dev for cros_ec */ 279 ec_dev->phys_name = dev_name(dev); 280 ec_dev->dev = dev; 281 ec_dev->priv = ec_uart; 282 ec_dev->irq = ec_uart->irq; 283 ec_dev->cmd_xfer = NULL; 284 ec_dev->pkt_xfer = cros_ec_uart_pkt_xfer; 285 ec_dev->din_size = sizeof(struct ec_host_response) + 286 sizeof(struct ec_response_get_protocol_info); 287 ec_dev->dout_size = sizeof(struct ec_host_request); 288 289 serdev_device_set_client_ops(serdev, &cros_ec_uart_client_ops); 290 291 ret = devm_serdev_device_open(dev, serdev); 292 if (ret) { 293 dev_err(dev, "Unable to open UART device"); 294 return ret; 295 } 296 297 ret = serdev_device_set_baudrate(serdev, ec_uart->baudrate); 298 if (ret < 0) { 299 dev_err(dev, "Failed to set up host baud rate (%d)", ret); 300 return ret; 301 } 302 303 serdev_device_set_flow_control(serdev, ec_uart->flowcontrol); 304 305 return cros_ec_register(ec_dev); 306 } 307 308 static void cros_ec_uart_remove(struct serdev_device *serdev) 309 { 310 struct cros_ec_device *ec_dev = serdev_device_get_drvdata(serdev); 311 312 cros_ec_unregister(ec_dev); 313 }; 314 315 static int __maybe_unused cros_ec_uart_suspend(struct device *dev) 316 { 317 struct cros_ec_device *ec_dev = dev_get_drvdata(dev); 318 319 return cros_ec_suspend(ec_dev); 320 } 321 322 static int __maybe_unused cros_ec_uart_resume(struct device *dev) 323 { 324 struct cros_ec_device *ec_dev = dev_get_drvdata(dev); 325 326 return cros_ec_resume(ec_dev); 327 } 328 329 static SIMPLE_DEV_PM_OPS(cros_ec_uart_pm_ops, cros_ec_uart_suspend, 330 cros_ec_uart_resume); 331 332 static const struct of_device_id cros_ec_uart_of_match[] = { 333 { .compatible = "google,cros-ec-uart" }, 334 {} 335 }; 336 MODULE_DEVICE_TABLE(of, cros_ec_uart_of_match); 337 338 #ifdef CONFIG_ACPI 339 static const struct acpi_device_id cros_ec_uart_acpi_id[] = { 340 { "GOOG0019", 0 }, 341 {} 342 }; 343 344 MODULE_DEVICE_TABLE(acpi, cros_ec_uart_acpi_id); 345 #endif 346 347 static struct serdev_device_driver cros_ec_uart_driver = { 348 .driver = { 349 .name = "cros-ec-uart", 350 .acpi_match_table = ACPI_PTR(cros_ec_uart_acpi_id), 351 .of_match_table = cros_ec_uart_of_match, 352 .pm = &cros_ec_uart_pm_ops, 353 }, 354 .probe = cros_ec_uart_probe, 355 .remove = cros_ec_uart_remove, 356 }; 357 358 module_serdev_device_driver(cros_ec_uart_driver); 359 360 MODULE_LICENSE("GPL"); 361 MODULE_DESCRIPTION("UART interface for ChromeOS Embedded Controller"); 362 MODULE_AUTHOR("Bhanu Prakash Maiya <bhanumaiya@chromium.org>"); 363