1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright (c) 2016, BayLibre, SAS. All rights reserved. 4 * Author: Neil Armstrong <narmstrong@baylibre.com> 5 * 6 * Copyright (c) 2010, Code Aurora Forum. All rights reserved. 7 * 8 * Driver for Semtech SX150X I2C GPIO Expanders 9 * The handling of the 4-bit chips (SX1501/SX1504/SX1507) is untested. 10 * 11 * Author: Gregory Bean <gbean@codeaurora.org> 12 */ 13 14 #include <linux/regmap.h> 15 #include <linux/i2c.h> 16 #include <linux/init.h> 17 #include <linux/interrupt.h> 18 #include <linux/irq.h> 19 #include <linux/mutex.h> 20 #include <linux/slab.h> 21 #include <linux/of.h> 22 #include <linux/of_device.h> 23 #include <linux/gpio/driver.h> 24 #include <linux/pinctrl/pinconf.h> 25 #include <linux/pinctrl/pinctrl.h> 26 #include <linux/pinctrl/pinmux.h> 27 #include <linux/pinctrl/pinconf-generic.h> 28 29 #include "core.h" 30 #include "pinconf.h" 31 #include "pinctrl-utils.h" 32 33 /* The chip models of sx150x */ 34 enum { 35 SX150X_123 = 0, 36 SX150X_456, 37 SX150X_789, 38 }; 39 enum { 40 SX150X_789_REG_MISC_AUTOCLEAR_OFF = 1 << 0, 41 SX150X_MAX_REGISTER = 0xad, 42 SX150X_IRQ_TYPE_EDGE_RISING = 0x1, 43 SX150X_IRQ_TYPE_EDGE_FALLING = 0x2, 44 SX150X_789_RESET_KEY1 = 0x12, 45 SX150X_789_RESET_KEY2 = 0x34, 46 }; 47 48 struct sx150x_123_pri { 49 u8 reg_pld_mode; 50 u8 reg_pld_table0; 51 u8 reg_pld_table1; 52 u8 reg_pld_table2; 53 u8 reg_pld_table3; 54 u8 reg_pld_table4; 55 u8 reg_advanced; 56 }; 57 58 struct sx150x_456_pri { 59 u8 reg_pld_mode; 60 u8 reg_pld_table0; 61 u8 reg_pld_table1; 62 u8 reg_pld_table2; 63 u8 reg_pld_table3; 64 u8 reg_pld_table4; 65 u8 reg_advanced; 66 }; 67 68 struct sx150x_789_pri { 69 u8 reg_drain; 70 u8 reg_polarity; 71 u8 reg_clock; 72 u8 reg_misc; 73 u8 reg_reset; 74 u8 ngpios; 75 }; 76 77 struct sx150x_device_data { 78 u8 model; 79 u8 reg_pullup; 80 u8 reg_pulldn; 81 u8 reg_dir; 82 u8 reg_data; 83 u8 reg_irq_mask; 84 u8 reg_irq_src; 85 u8 reg_sense; 86 u8 ngpios; 87 union { 88 struct sx150x_123_pri x123; 89 struct sx150x_456_pri x456; 90 struct sx150x_789_pri x789; 91 } pri; 92 const struct pinctrl_pin_desc *pins; 93 unsigned int npins; 94 }; 95 96 struct sx150x_pinctrl { 97 struct device *dev; 98 struct i2c_client *client; 99 struct pinctrl_dev *pctldev; 100 struct pinctrl_desc pinctrl_desc; 101 struct gpio_chip gpio; 102 struct regmap *regmap; 103 struct { 104 u32 sense; 105 u32 masked; 106 } irq; 107 struct mutex lock; 108 const struct sx150x_device_data *data; 109 }; 110 111 static const struct pinctrl_pin_desc sx150x_4_pins[] = { 112 PINCTRL_PIN(0, "gpio0"), 113 PINCTRL_PIN(1, "gpio1"), 114 PINCTRL_PIN(2, "gpio2"), 115 PINCTRL_PIN(3, "gpio3"), 116 PINCTRL_PIN(4, "oscio"), 117 }; 118 119 static const struct pinctrl_pin_desc sx150x_8_pins[] = { 120 PINCTRL_PIN(0, "gpio0"), 121 PINCTRL_PIN(1, "gpio1"), 122 PINCTRL_PIN(2, "gpio2"), 123 PINCTRL_PIN(3, "gpio3"), 124 PINCTRL_PIN(4, "gpio4"), 125 PINCTRL_PIN(5, "gpio5"), 126 PINCTRL_PIN(6, "gpio6"), 127 PINCTRL_PIN(7, "gpio7"), 128 PINCTRL_PIN(8, "oscio"), 129 }; 130 131 static const struct pinctrl_pin_desc sx150x_16_pins[] = { 132 PINCTRL_PIN(0, "gpio0"), 133 PINCTRL_PIN(1, "gpio1"), 134 PINCTRL_PIN(2, "gpio2"), 135 PINCTRL_PIN(3, "gpio3"), 136 PINCTRL_PIN(4, "gpio4"), 137 PINCTRL_PIN(5, "gpio5"), 138 PINCTRL_PIN(6, "gpio6"), 139 PINCTRL_PIN(7, "gpio7"), 140 PINCTRL_PIN(8, "gpio8"), 141 PINCTRL_PIN(9, "gpio9"), 142 PINCTRL_PIN(10, "gpio10"), 143 PINCTRL_PIN(11, "gpio11"), 144 PINCTRL_PIN(12, "gpio12"), 145 PINCTRL_PIN(13, "gpio13"), 146 PINCTRL_PIN(14, "gpio14"), 147 PINCTRL_PIN(15, "gpio15"), 148 PINCTRL_PIN(16, "oscio"), 149 }; 150 151 static const struct sx150x_device_data sx1501q_device_data = { 152 .model = SX150X_123, 153 .reg_pullup = 0x02, 154 .reg_pulldn = 0x03, 155 .reg_dir = 0x01, 156 .reg_data = 0x00, 157 .reg_irq_mask = 0x05, 158 .reg_irq_src = 0x08, 159 .reg_sense = 0x07, 160 .pri.x123 = { 161 .reg_pld_mode = 0x10, 162 .reg_pld_table0 = 0x11, 163 .reg_pld_table2 = 0x13, 164 .reg_advanced = 0xad, 165 }, 166 .ngpios = 4, 167 .pins = sx150x_4_pins, 168 .npins = 4, /* oscio not available */ 169 }; 170 171 static const struct sx150x_device_data sx1502q_device_data = { 172 .model = SX150X_123, 173 .reg_pullup = 0x02, 174 .reg_pulldn = 0x03, 175 .reg_dir = 0x01, 176 .reg_data = 0x00, 177 .reg_irq_mask = 0x05, 178 .reg_irq_src = 0x08, 179 .reg_sense = 0x06, 180 .pri.x123 = { 181 .reg_pld_mode = 0x10, 182 .reg_pld_table0 = 0x11, 183 .reg_pld_table1 = 0x12, 184 .reg_pld_table2 = 0x13, 185 .reg_pld_table3 = 0x14, 186 .reg_pld_table4 = 0x15, 187 .reg_advanced = 0xad, 188 }, 189 .ngpios = 8, 190 .pins = sx150x_8_pins, 191 .npins = 8, /* oscio not available */ 192 }; 193 194 static const struct sx150x_device_data sx1503q_device_data = { 195 .model = SX150X_123, 196 .reg_pullup = 0x04, 197 .reg_pulldn = 0x06, 198 .reg_dir = 0x02, 199 .reg_data = 0x00, 200 .reg_irq_mask = 0x08, 201 .reg_irq_src = 0x0e, 202 .reg_sense = 0x0a, 203 .pri.x123 = { 204 .reg_pld_mode = 0x20, 205 .reg_pld_table0 = 0x22, 206 .reg_pld_table1 = 0x24, 207 .reg_pld_table2 = 0x26, 208 .reg_pld_table3 = 0x28, 209 .reg_pld_table4 = 0x2a, 210 .reg_advanced = 0xad, 211 }, 212 .ngpios = 16, 213 .pins = sx150x_16_pins, 214 .npins = 16, /* oscio not available */ 215 }; 216 217 static const struct sx150x_device_data sx1504q_device_data = { 218 .model = SX150X_456, 219 .reg_pullup = 0x02, 220 .reg_pulldn = 0x03, 221 .reg_dir = 0x01, 222 .reg_data = 0x00, 223 .reg_irq_mask = 0x05, 224 .reg_irq_src = 0x08, 225 .reg_sense = 0x07, 226 .pri.x456 = { 227 .reg_pld_mode = 0x10, 228 .reg_pld_table0 = 0x11, 229 .reg_pld_table2 = 0x13, 230 }, 231 .ngpios = 4, 232 .pins = sx150x_4_pins, 233 .npins = 4, /* oscio not available */ 234 }; 235 236 static const struct sx150x_device_data sx1505q_device_data = { 237 .model = SX150X_456, 238 .reg_pullup = 0x02, 239 .reg_pulldn = 0x03, 240 .reg_dir = 0x01, 241 .reg_data = 0x00, 242 .reg_irq_mask = 0x05, 243 .reg_irq_src = 0x08, 244 .reg_sense = 0x06, 245 .pri.x456 = { 246 .reg_pld_mode = 0x10, 247 .reg_pld_table0 = 0x11, 248 .reg_pld_table1 = 0x12, 249 .reg_pld_table2 = 0x13, 250 .reg_pld_table3 = 0x14, 251 .reg_pld_table4 = 0x15, 252 }, 253 .ngpios = 8, 254 .pins = sx150x_8_pins, 255 .npins = 8, /* oscio not available */ 256 }; 257 258 static const struct sx150x_device_data sx1506q_device_data = { 259 .model = SX150X_456, 260 .reg_pullup = 0x04, 261 .reg_pulldn = 0x06, 262 .reg_dir = 0x02, 263 .reg_data = 0x00, 264 .reg_irq_mask = 0x08, 265 .reg_irq_src = 0x0e, 266 .reg_sense = 0x0a, 267 .pri.x456 = { 268 .reg_pld_mode = 0x20, 269 .reg_pld_table0 = 0x22, 270 .reg_pld_table1 = 0x24, 271 .reg_pld_table2 = 0x26, 272 .reg_pld_table3 = 0x28, 273 .reg_pld_table4 = 0x2a, 274 .reg_advanced = 0xad, 275 }, 276 .ngpios = 16, 277 .pins = sx150x_16_pins, 278 .npins = 16, /* oscio not available */ 279 }; 280 281 static const struct sx150x_device_data sx1507q_device_data = { 282 .model = SX150X_789, 283 .reg_pullup = 0x03, 284 .reg_pulldn = 0x04, 285 .reg_dir = 0x07, 286 .reg_data = 0x08, 287 .reg_irq_mask = 0x09, 288 .reg_irq_src = 0x0b, 289 .reg_sense = 0x0a, 290 .pri.x789 = { 291 .reg_drain = 0x05, 292 .reg_polarity = 0x06, 293 .reg_clock = 0x0d, 294 .reg_misc = 0x0e, 295 .reg_reset = 0x7d, 296 }, 297 .ngpios = 4, 298 .pins = sx150x_4_pins, 299 .npins = ARRAY_SIZE(sx150x_4_pins), 300 }; 301 302 static const struct sx150x_device_data sx1508q_device_data = { 303 .model = SX150X_789, 304 .reg_pullup = 0x03, 305 .reg_pulldn = 0x04, 306 .reg_dir = 0x07, 307 .reg_data = 0x08, 308 .reg_irq_mask = 0x09, 309 .reg_irq_src = 0x0c, 310 .reg_sense = 0x0a, 311 .pri.x789 = { 312 .reg_drain = 0x05, 313 .reg_polarity = 0x06, 314 .reg_clock = 0x0f, 315 .reg_misc = 0x10, 316 .reg_reset = 0x7d, 317 }, 318 .ngpios = 8, 319 .pins = sx150x_8_pins, 320 .npins = ARRAY_SIZE(sx150x_8_pins), 321 }; 322 323 static const struct sx150x_device_data sx1509q_device_data = { 324 .model = SX150X_789, 325 .reg_pullup = 0x06, 326 .reg_pulldn = 0x08, 327 .reg_dir = 0x0e, 328 .reg_data = 0x10, 329 .reg_irq_mask = 0x12, 330 .reg_irq_src = 0x18, 331 .reg_sense = 0x14, 332 .pri.x789 = { 333 .reg_drain = 0x0a, 334 .reg_polarity = 0x0c, 335 .reg_clock = 0x1e, 336 .reg_misc = 0x1f, 337 .reg_reset = 0x7d, 338 }, 339 .ngpios = 16, 340 .pins = sx150x_16_pins, 341 .npins = ARRAY_SIZE(sx150x_16_pins), 342 }; 343 344 static int sx150x_pinctrl_get_groups_count(struct pinctrl_dev *pctldev) 345 { 346 return 0; 347 } 348 349 static const char *sx150x_pinctrl_get_group_name(struct pinctrl_dev *pctldev, 350 unsigned int group) 351 { 352 return NULL; 353 } 354 355 static int sx150x_pinctrl_get_group_pins(struct pinctrl_dev *pctldev, 356 unsigned int group, 357 const unsigned int **pins, 358 unsigned int *num_pins) 359 { 360 return -ENOTSUPP; 361 } 362 363 static const struct pinctrl_ops sx150x_pinctrl_ops = { 364 .get_groups_count = sx150x_pinctrl_get_groups_count, 365 .get_group_name = sx150x_pinctrl_get_group_name, 366 .get_group_pins = sx150x_pinctrl_get_group_pins, 367 #ifdef CONFIG_OF 368 .dt_node_to_map = pinconf_generic_dt_node_to_map_pin, 369 .dt_free_map = pinctrl_utils_free_map, 370 #endif 371 }; 372 373 static bool sx150x_pin_is_oscio(struct sx150x_pinctrl *pctl, unsigned int pin) 374 { 375 if (pin >= pctl->data->npins) 376 return false; 377 378 /* OSCIO pin is only present in 789 devices */ 379 if (pctl->data->model != SX150X_789) 380 return false; 381 382 return !strcmp(pctl->data->pins[pin].name, "oscio"); 383 } 384 385 static int sx150x_gpio_get_direction(struct gpio_chip *chip, 386 unsigned int offset) 387 { 388 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 389 unsigned int value; 390 int ret; 391 392 if (sx150x_pin_is_oscio(pctl, offset)) 393 return GPIO_LINE_DIRECTION_OUT; 394 395 ret = regmap_read(pctl->regmap, pctl->data->reg_dir, &value); 396 if (ret < 0) 397 return ret; 398 399 if (value & BIT(offset)) 400 return GPIO_LINE_DIRECTION_IN; 401 402 return GPIO_LINE_DIRECTION_OUT; 403 } 404 405 static int sx150x_gpio_get(struct gpio_chip *chip, unsigned int offset) 406 { 407 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 408 unsigned int value; 409 int ret; 410 411 if (sx150x_pin_is_oscio(pctl, offset)) 412 return -EINVAL; 413 414 ret = regmap_read(pctl->regmap, pctl->data->reg_data, &value); 415 if (ret < 0) 416 return ret; 417 418 return !!(value & BIT(offset)); 419 } 420 421 static int __sx150x_gpio_set(struct sx150x_pinctrl *pctl, unsigned int offset, 422 int value) 423 { 424 return regmap_write_bits(pctl->regmap, pctl->data->reg_data, 425 BIT(offset), value ? BIT(offset) : 0); 426 } 427 428 static int sx150x_gpio_oscio_set(struct sx150x_pinctrl *pctl, 429 int value) 430 { 431 return regmap_write(pctl->regmap, 432 pctl->data->pri.x789.reg_clock, 433 (value ? 0x1f : 0x10)); 434 } 435 436 static void sx150x_gpio_set(struct gpio_chip *chip, unsigned int offset, 437 int value) 438 { 439 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 440 441 if (sx150x_pin_is_oscio(pctl, offset)) 442 sx150x_gpio_oscio_set(pctl, value); 443 else 444 __sx150x_gpio_set(pctl, offset, value); 445 } 446 447 static void sx150x_gpio_set_multiple(struct gpio_chip *chip, 448 unsigned long *mask, 449 unsigned long *bits) 450 { 451 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 452 453 regmap_write_bits(pctl->regmap, pctl->data->reg_data, *mask, *bits); 454 } 455 456 static int sx150x_gpio_direction_input(struct gpio_chip *chip, 457 unsigned int offset) 458 { 459 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 460 461 if (sx150x_pin_is_oscio(pctl, offset)) 462 return -EINVAL; 463 464 return regmap_write_bits(pctl->regmap, 465 pctl->data->reg_dir, 466 BIT(offset), BIT(offset)); 467 } 468 469 static int sx150x_gpio_direction_output(struct gpio_chip *chip, 470 unsigned int offset, int value) 471 { 472 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 473 int ret; 474 475 if (sx150x_pin_is_oscio(pctl, offset)) 476 return sx150x_gpio_oscio_set(pctl, value); 477 478 ret = __sx150x_gpio_set(pctl, offset, value); 479 if (ret < 0) 480 return ret; 481 482 return regmap_write_bits(pctl->regmap, 483 pctl->data->reg_dir, 484 BIT(offset), 0); 485 } 486 487 static void sx150x_irq_mask(struct irq_data *d) 488 { 489 struct gpio_chip *gc = irq_data_get_irq_chip_data(d); 490 struct sx150x_pinctrl *pctl = gpiochip_get_data(gc); 491 unsigned int n = irqd_to_hwirq(d); 492 493 pctl->irq.masked |= BIT(n); 494 gpiochip_disable_irq(gc, n); 495 } 496 497 static void sx150x_irq_unmask(struct irq_data *d) 498 { 499 struct gpio_chip *gc = irq_data_get_irq_chip_data(d); 500 struct sx150x_pinctrl *pctl = gpiochip_get_data(gc); 501 unsigned int n = irqd_to_hwirq(d); 502 503 gpiochip_enable_irq(gc, n); 504 pctl->irq.masked &= ~BIT(n); 505 } 506 507 static void sx150x_irq_set_sense(struct sx150x_pinctrl *pctl, 508 unsigned int line, unsigned int sense) 509 { 510 /* 511 * Every interrupt line is represented by two bits shifted 512 * proportionally to the line number 513 */ 514 const unsigned int n = line * 2; 515 const unsigned int mask = ~((SX150X_IRQ_TYPE_EDGE_RISING | 516 SX150X_IRQ_TYPE_EDGE_FALLING) << n); 517 518 pctl->irq.sense &= mask; 519 pctl->irq.sense |= sense << n; 520 } 521 522 static int sx150x_irq_set_type(struct irq_data *d, unsigned int flow_type) 523 { 524 struct gpio_chip *gc = irq_data_get_irq_chip_data(d); 525 struct sx150x_pinctrl *pctl = gpiochip_get_data(gc); 526 unsigned int n, val = 0; 527 528 if (flow_type & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) 529 return -EINVAL; 530 531 n = irqd_to_hwirq(d); 532 533 if (flow_type & IRQ_TYPE_EDGE_RISING) 534 val |= SX150X_IRQ_TYPE_EDGE_RISING; 535 if (flow_type & IRQ_TYPE_EDGE_FALLING) 536 val |= SX150X_IRQ_TYPE_EDGE_FALLING; 537 538 sx150x_irq_set_sense(pctl, n, val); 539 return 0; 540 } 541 542 static irqreturn_t sx150x_irq_thread_fn(int irq, void *dev_id) 543 { 544 struct sx150x_pinctrl *pctl = (struct sx150x_pinctrl *)dev_id; 545 unsigned long n, status; 546 unsigned int val; 547 int err; 548 549 err = regmap_read(pctl->regmap, pctl->data->reg_irq_src, &val); 550 if (err < 0) 551 return IRQ_NONE; 552 553 err = regmap_write(pctl->regmap, pctl->data->reg_irq_src, val); 554 if (err < 0) 555 return IRQ_NONE; 556 557 status = val; 558 for_each_set_bit(n, &status, pctl->data->ngpios) 559 handle_nested_irq(irq_find_mapping(pctl->gpio.irq.domain, n)); 560 561 return IRQ_HANDLED; 562 } 563 564 static void sx150x_irq_bus_lock(struct irq_data *d) 565 { 566 struct gpio_chip *gc = irq_data_get_irq_chip_data(d); 567 struct sx150x_pinctrl *pctl = gpiochip_get_data(gc); 568 569 mutex_lock(&pctl->lock); 570 } 571 572 static void sx150x_irq_bus_sync_unlock(struct irq_data *d) 573 { 574 struct gpio_chip *gc = irq_data_get_irq_chip_data(d); 575 struct sx150x_pinctrl *pctl = gpiochip_get_data(gc); 576 577 regmap_write(pctl->regmap, pctl->data->reg_irq_mask, pctl->irq.masked); 578 regmap_write(pctl->regmap, pctl->data->reg_sense, pctl->irq.sense); 579 mutex_unlock(&pctl->lock); 580 } 581 582 583 static void sx150x_irq_print_chip(struct irq_data *d, struct seq_file *p) 584 { 585 struct gpio_chip *gc = irq_data_get_irq_chip_data(d); 586 struct sx150x_pinctrl *pctl = gpiochip_get_data(gc); 587 588 seq_printf(p, pctl->client->name); 589 } 590 591 static const struct irq_chip sx150x_irq_chip = { 592 .irq_mask = sx150x_irq_mask, 593 .irq_unmask = sx150x_irq_unmask, 594 .irq_set_type = sx150x_irq_set_type, 595 .irq_bus_lock = sx150x_irq_bus_lock, 596 .irq_bus_sync_unlock = sx150x_irq_bus_sync_unlock, 597 .irq_print_chip = sx150x_irq_print_chip, 598 .flags = IRQCHIP_IMMUTABLE, 599 GPIOCHIP_IRQ_RESOURCE_HELPERS, 600 }; 601 602 static int sx150x_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, 603 unsigned long *config) 604 { 605 struct sx150x_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev); 606 unsigned int param = pinconf_to_config_param(*config); 607 int ret; 608 u32 arg; 609 unsigned int data; 610 611 if (sx150x_pin_is_oscio(pctl, pin)) { 612 switch (param) { 613 case PIN_CONFIG_DRIVE_PUSH_PULL: 614 case PIN_CONFIG_OUTPUT: 615 ret = regmap_read(pctl->regmap, 616 pctl->data->pri.x789.reg_clock, 617 &data); 618 if (ret < 0) 619 return ret; 620 621 if (param == PIN_CONFIG_DRIVE_PUSH_PULL) 622 arg = (data & 0x1f) ? 1 : 0; 623 else { 624 if ((data & 0x1f) == 0x1f) 625 arg = 1; 626 else if ((data & 0x1f) == 0x10) 627 arg = 0; 628 else 629 return -EINVAL; 630 } 631 632 break; 633 default: 634 return -ENOTSUPP; 635 } 636 637 goto out; 638 } 639 640 switch (param) { 641 case PIN_CONFIG_BIAS_PULL_DOWN: 642 ret = regmap_read(pctl->regmap, 643 pctl->data->reg_pulldn, 644 &data); 645 data &= BIT(pin); 646 647 if (ret < 0) 648 return ret; 649 650 if (!ret) 651 return -EINVAL; 652 653 arg = 1; 654 break; 655 656 case PIN_CONFIG_BIAS_PULL_UP: 657 ret = regmap_read(pctl->regmap, 658 pctl->data->reg_pullup, 659 &data); 660 data &= BIT(pin); 661 662 if (ret < 0) 663 return ret; 664 665 if (!ret) 666 return -EINVAL; 667 668 arg = 1; 669 break; 670 671 case PIN_CONFIG_DRIVE_OPEN_DRAIN: 672 if (pctl->data->model != SX150X_789) 673 return -ENOTSUPP; 674 675 ret = regmap_read(pctl->regmap, 676 pctl->data->pri.x789.reg_drain, 677 &data); 678 data &= BIT(pin); 679 680 if (ret < 0) 681 return ret; 682 683 if (!data) 684 return -EINVAL; 685 686 arg = 1; 687 break; 688 689 case PIN_CONFIG_DRIVE_PUSH_PULL: 690 if (pctl->data->model != SX150X_789) 691 arg = true; 692 else { 693 ret = regmap_read(pctl->regmap, 694 pctl->data->pri.x789.reg_drain, 695 &data); 696 data &= BIT(pin); 697 698 if (ret < 0) 699 return ret; 700 701 if (data) 702 return -EINVAL; 703 704 arg = 1; 705 } 706 break; 707 708 case PIN_CONFIG_OUTPUT: 709 ret = sx150x_gpio_get_direction(&pctl->gpio, pin); 710 if (ret < 0) 711 return ret; 712 713 if (ret == GPIO_LINE_DIRECTION_IN) 714 return -EINVAL; 715 716 ret = sx150x_gpio_get(&pctl->gpio, pin); 717 if (ret < 0) 718 return ret; 719 720 arg = ret; 721 break; 722 723 default: 724 return -ENOTSUPP; 725 } 726 727 out: 728 *config = pinconf_to_config_packed(param, arg); 729 730 return 0; 731 } 732 733 static int sx150x_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin, 734 unsigned long *configs, unsigned int num_configs) 735 { 736 struct sx150x_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev); 737 enum pin_config_param param; 738 u32 arg; 739 int i; 740 int ret; 741 742 for (i = 0; i < num_configs; i++) { 743 param = pinconf_to_config_param(configs[i]); 744 arg = pinconf_to_config_argument(configs[i]); 745 746 if (sx150x_pin_is_oscio(pctl, pin)) { 747 if (param == PIN_CONFIG_OUTPUT) { 748 ret = sx150x_gpio_direction_output(&pctl->gpio, 749 pin, arg); 750 if (ret < 0) 751 return ret; 752 753 continue; 754 } else 755 return -ENOTSUPP; 756 } 757 758 switch (param) { 759 case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: 760 case PIN_CONFIG_BIAS_DISABLE: 761 ret = regmap_write_bits(pctl->regmap, 762 pctl->data->reg_pulldn, 763 BIT(pin), 0); 764 if (ret < 0) 765 return ret; 766 767 ret = regmap_write_bits(pctl->regmap, 768 pctl->data->reg_pullup, 769 BIT(pin), 0); 770 if (ret < 0) 771 return ret; 772 773 break; 774 775 case PIN_CONFIG_BIAS_PULL_UP: 776 ret = regmap_write_bits(pctl->regmap, 777 pctl->data->reg_pullup, 778 BIT(pin), BIT(pin)); 779 if (ret < 0) 780 return ret; 781 782 break; 783 784 case PIN_CONFIG_BIAS_PULL_DOWN: 785 ret = regmap_write_bits(pctl->regmap, 786 pctl->data->reg_pulldn, 787 BIT(pin), BIT(pin)); 788 if (ret < 0) 789 return ret; 790 791 break; 792 793 case PIN_CONFIG_DRIVE_OPEN_DRAIN: 794 if (pctl->data->model != SX150X_789 || 795 sx150x_pin_is_oscio(pctl, pin)) 796 return -ENOTSUPP; 797 798 ret = regmap_write_bits(pctl->regmap, 799 pctl->data->pri.x789.reg_drain, 800 BIT(pin), BIT(pin)); 801 if (ret < 0) 802 return ret; 803 804 break; 805 806 case PIN_CONFIG_DRIVE_PUSH_PULL: 807 if (pctl->data->model != SX150X_789 || 808 sx150x_pin_is_oscio(pctl, pin)) 809 return 0; 810 811 ret = regmap_write_bits(pctl->regmap, 812 pctl->data->pri.x789.reg_drain, 813 BIT(pin), 0); 814 if (ret < 0) 815 return ret; 816 817 break; 818 819 case PIN_CONFIG_OUTPUT: 820 ret = sx150x_gpio_direction_output(&pctl->gpio, 821 pin, arg); 822 if (ret < 0) 823 return ret; 824 825 break; 826 827 default: 828 return -ENOTSUPP; 829 } 830 } /* for each config */ 831 832 return 0; 833 } 834 835 static const struct pinconf_ops sx150x_pinconf_ops = { 836 .pin_config_get = sx150x_pinconf_get, 837 .pin_config_set = sx150x_pinconf_set, 838 .is_generic = true, 839 }; 840 841 static const struct i2c_device_id sx150x_id[] = { 842 {"sx1501q", (kernel_ulong_t) &sx1501q_device_data }, 843 {"sx1502q", (kernel_ulong_t) &sx1502q_device_data }, 844 {"sx1503q", (kernel_ulong_t) &sx1503q_device_data }, 845 {"sx1504q", (kernel_ulong_t) &sx1504q_device_data }, 846 {"sx1505q", (kernel_ulong_t) &sx1505q_device_data }, 847 {"sx1506q", (kernel_ulong_t) &sx1506q_device_data }, 848 {"sx1507q", (kernel_ulong_t) &sx1507q_device_data }, 849 {"sx1508q", (kernel_ulong_t) &sx1508q_device_data }, 850 {"sx1509q", (kernel_ulong_t) &sx1509q_device_data }, 851 {} 852 }; 853 854 static const struct of_device_id sx150x_of_match[] = { 855 { .compatible = "semtech,sx1501q", .data = &sx1501q_device_data }, 856 { .compatible = "semtech,sx1502q", .data = &sx1502q_device_data }, 857 { .compatible = "semtech,sx1503q", .data = &sx1503q_device_data }, 858 { .compatible = "semtech,sx1504q", .data = &sx1504q_device_data }, 859 { .compatible = "semtech,sx1505q", .data = &sx1505q_device_data }, 860 { .compatible = "semtech,sx1506q", .data = &sx1506q_device_data }, 861 { .compatible = "semtech,sx1507q", .data = &sx1507q_device_data }, 862 { .compatible = "semtech,sx1508q", .data = &sx1508q_device_data }, 863 { .compatible = "semtech,sx1509q", .data = &sx1509q_device_data }, 864 {}, 865 }; 866 867 static int sx150x_reset(struct sx150x_pinctrl *pctl) 868 { 869 int err; 870 871 err = i2c_smbus_write_byte_data(pctl->client, 872 pctl->data->pri.x789.reg_reset, 873 SX150X_789_RESET_KEY1); 874 if (err < 0) 875 return err; 876 877 err = i2c_smbus_write_byte_data(pctl->client, 878 pctl->data->pri.x789.reg_reset, 879 SX150X_789_RESET_KEY2); 880 return err; 881 } 882 883 static int sx150x_init_misc(struct sx150x_pinctrl *pctl) 884 { 885 u8 reg, value; 886 887 switch (pctl->data->model) { 888 case SX150X_789: 889 reg = pctl->data->pri.x789.reg_misc; 890 value = SX150X_789_REG_MISC_AUTOCLEAR_OFF; 891 break; 892 case SX150X_456: 893 reg = pctl->data->pri.x456.reg_advanced; 894 value = 0x00; 895 896 /* 897 * Only SX1506 has RegAdvanced, SX1504/5 are expected 898 * to initialize this offset to zero 899 */ 900 if (!reg) 901 return 0; 902 break; 903 case SX150X_123: 904 reg = pctl->data->pri.x123.reg_advanced; 905 value = 0x00; 906 break; 907 default: 908 WARN(1, "Unknown chip model %d\n", pctl->data->model); 909 return -EINVAL; 910 } 911 912 return regmap_write(pctl->regmap, reg, value); 913 } 914 915 static int sx150x_init_hw(struct sx150x_pinctrl *pctl) 916 { 917 const u8 reg[] = { 918 [SX150X_789] = pctl->data->pri.x789.reg_polarity, 919 [SX150X_456] = pctl->data->pri.x456.reg_pld_mode, 920 [SX150X_123] = pctl->data->pri.x123.reg_pld_mode, 921 }; 922 int err; 923 924 if (pctl->data->model == SX150X_789 && 925 of_property_read_bool(pctl->dev->of_node, "semtech,probe-reset")) { 926 err = sx150x_reset(pctl); 927 if (err < 0) 928 return err; 929 } 930 931 err = sx150x_init_misc(pctl); 932 if (err < 0) 933 return err; 934 935 /* Set all pins to work in normal mode */ 936 return regmap_write(pctl->regmap, reg[pctl->data->model], 0); 937 } 938 939 static int sx150x_regmap_reg_width(struct sx150x_pinctrl *pctl, 940 unsigned int reg) 941 { 942 const struct sx150x_device_data *data = pctl->data; 943 944 if (reg == data->reg_sense) { 945 /* 946 * RegSense packs two bits of configuration per GPIO, 947 * so we'd need to read twice as many bits as there 948 * are GPIO in our chip 949 */ 950 return 2 * data->ngpios; 951 } else if ((data->model == SX150X_789 && 952 (reg == data->pri.x789.reg_misc || 953 reg == data->pri.x789.reg_clock || 954 reg == data->pri.x789.reg_reset)) 955 || 956 (data->model == SX150X_123 && 957 reg == data->pri.x123.reg_advanced) 958 || 959 (data->model == SX150X_456 && 960 data->pri.x456.reg_advanced && 961 reg == data->pri.x456.reg_advanced)) { 962 return 8; 963 } else { 964 return data->ngpios; 965 } 966 } 967 968 static unsigned int sx150x_maybe_swizzle(struct sx150x_pinctrl *pctl, 969 unsigned int reg, unsigned int val) 970 { 971 unsigned int a, b; 972 const struct sx150x_device_data *data = pctl->data; 973 974 /* 975 * Whereas SX1509 presents RegSense in a simple layout as such: 976 * reg [ f f e e d d c c ] 977 * reg + 1 [ b b a a 9 9 8 8 ] 978 * reg + 2 [ 7 7 6 6 5 5 4 4 ] 979 * reg + 3 [ 3 3 2 2 1 1 0 0 ] 980 * 981 * SX1503 and SX1506 deviate from that data layout, instead storing 982 * their contents as follows: 983 * 984 * reg [ f f e e d d c c ] 985 * reg + 1 [ 7 7 6 6 5 5 4 4 ] 986 * reg + 2 [ b b a a 9 9 8 8 ] 987 * reg + 3 [ 3 3 2 2 1 1 0 0 ] 988 * 989 * so, taking that into account, we swap two 990 * inner bytes of a 4-byte result 991 */ 992 993 if (reg == data->reg_sense && 994 data->ngpios == 16 && 995 (data->model == SX150X_123 || 996 data->model == SX150X_456)) { 997 a = val & 0x00ff0000; 998 b = val & 0x0000ff00; 999 1000 val &= 0xff0000ff; 1001 val |= b << 8; 1002 val |= a >> 8; 1003 } 1004 1005 return val; 1006 } 1007 1008 /* 1009 * In order to mask the differences between 16 and 8 bit expander 1010 * devices we set up a sligthly ficticious regmap that pretends to be 1011 * a set of 32-bit (to accommodate RegSenseLow/RegSenseHigh 1012 * pair/quartet) registers and transparently reconstructs those 1013 * registers via multiple I2C/SMBus reads 1014 * 1015 * This way the rest of the driver code, interfacing with the chip via 1016 * regmap API, can work assuming that each GPIO pin is represented by 1017 * a group of bits at an offset proportional to GPIO number within a 1018 * given register. 1019 */ 1020 static int sx150x_regmap_reg_read(void *context, unsigned int reg, 1021 unsigned int *result) 1022 { 1023 int ret, n; 1024 struct sx150x_pinctrl *pctl = context; 1025 struct i2c_client *i2c = pctl->client; 1026 const int width = sx150x_regmap_reg_width(pctl, reg); 1027 unsigned int idx, val; 1028 1029 /* 1030 * There are four potential cases covered by this function: 1031 * 1032 * 1) 8-pin chip, single configuration bit register 1033 * 1034 * This is trivial the code below just needs to read: 1035 * reg [ 7 6 5 4 3 2 1 0 ] 1036 * 1037 * 2) 8-pin chip, double configuration bit register (RegSense) 1038 * 1039 * The read will be done as follows: 1040 * reg [ 7 7 6 6 5 5 4 4 ] 1041 * reg + 1 [ 3 3 2 2 1 1 0 0 ] 1042 * 1043 * 3) 16-pin chip, single configuration bit register 1044 * 1045 * The read will be done as follows: 1046 * reg [ f e d c b a 9 8 ] 1047 * reg + 1 [ 7 6 5 4 3 2 1 0 ] 1048 * 1049 * 4) 16-pin chip, double configuration bit register (RegSense) 1050 * 1051 * The read will be done as follows: 1052 * reg [ f f e e d d c c ] 1053 * reg + 1 [ b b a a 9 9 8 8 ] 1054 * reg + 2 [ 7 7 6 6 5 5 4 4 ] 1055 * reg + 3 [ 3 3 2 2 1 1 0 0 ] 1056 */ 1057 1058 for (n = width, val = 0, idx = reg; n > 0; n -= 8, idx++) { 1059 val <<= 8; 1060 1061 ret = i2c_smbus_read_byte_data(i2c, idx); 1062 if (ret < 0) 1063 return ret; 1064 1065 val |= ret; 1066 } 1067 1068 *result = sx150x_maybe_swizzle(pctl, reg, val); 1069 1070 return 0; 1071 } 1072 1073 static int sx150x_regmap_reg_write(void *context, unsigned int reg, 1074 unsigned int val) 1075 { 1076 int ret, n; 1077 struct sx150x_pinctrl *pctl = context; 1078 struct i2c_client *i2c = pctl->client; 1079 const int width = sx150x_regmap_reg_width(pctl, reg); 1080 1081 val = sx150x_maybe_swizzle(pctl, reg, val); 1082 1083 n = (width - 1) & ~7; 1084 do { 1085 const u8 byte = (val >> n) & 0xff; 1086 1087 ret = i2c_smbus_write_byte_data(i2c, reg, byte); 1088 if (ret < 0) 1089 return ret; 1090 1091 reg++; 1092 n -= 8; 1093 } while (n >= 0); 1094 1095 return 0; 1096 } 1097 1098 static bool sx150x_reg_volatile(struct device *dev, unsigned int reg) 1099 { 1100 struct sx150x_pinctrl *pctl = i2c_get_clientdata(to_i2c_client(dev)); 1101 1102 return reg == pctl->data->reg_irq_src || reg == pctl->data->reg_data; 1103 } 1104 1105 static const struct regmap_config sx150x_regmap_config = { 1106 .reg_bits = 8, 1107 .val_bits = 32, 1108 1109 .cache_type = REGCACHE_RBTREE, 1110 1111 .reg_read = sx150x_regmap_reg_read, 1112 .reg_write = sx150x_regmap_reg_write, 1113 1114 .max_register = SX150X_MAX_REGISTER, 1115 .volatile_reg = sx150x_reg_volatile, 1116 }; 1117 1118 static int sx150x_probe(struct i2c_client *client) 1119 { 1120 const struct i2c_device_id *id = i2c_client_get_device_id(client); 1121 static const u32 i2c_funcs = I2C_FUNC_SMBUS_BYTE_DATA | 1122 I2C_FUNC_SMBUS_WRITE_WORD_DATA; 1123 struct device *dev = &client->dev; 1124 struct sx150x_pinctrl *pctl; 1125 int ret; 1126 1127 if (!i2c_check_functionality(client->adapter, i2c_funcs)) 1128 return -ENOSYS; 1129 1130 pctl = devm_kzalloc(dev, sizeof(*pctl), GFP_KERNEL); 1131 if (!pctl) 1132 return -ENOMEM; 1133 1134 i2c_set_clientdata(client, pctl); 1135 1136 pctl->dev = dev; 1137 pctl->client = client; 1138 1139 if (dev->of_node) 1140 pctl->data = of_device_get_match_data(dev); 1141 else 1142 pctl->data = (struct sx150x_device_data *)id->driver_data; 1143 1144 if (!pctl->data) 1145 return -EINVAL; 1146 1147 pctl->regmap = devm_regmap_init(dev, NULL, pctl, 1148 &sx150x_regmap_config); 1149 if (IS_ERR(pctl->regmap)) { 1150 ret = PTR_ERR(pctl->regmap); 1151 dev_err(dev, "Failed to allocate register map: %d\n", 1152 ret); 1153 return ret; 1154 } 1155 1156 mutex_init(&pctl->lock); 1157 1158 ret = sx150x_init_hw(pctl); 1159 if (ret) 1160 return ret; 1161 1162 /* Pinctrl_desc */ 1163 pctl->pinctrl_desc.name = "sx150x-pinctrl"; 1164 pctl->pinctrl_desc.pctlops = &sx150x_pinctrl_ops; 1165 pctl->pinctrl_desc.confops = &sx150x_pinconf_ops; 1166 pctl->pinctrl_desc.pins = pctl->data->pins; 1167 pctl->pinctrl_desc.npins = pctl->data->npins; 1168 pctl->pinctrl_desc.owner = THIS_MODULE; 1169 1170 ret = devm_pinctrl_register_and_init(dev, &pctl->pinctrl_desc, 1171 pctl, &pctl->pctldev); 1172 if (ret) { 1173 dev_err(dev, "Failed to register pinctrl device\n"); 1174 return ret; 1175 } 1176 1177 /* Register GPIO controller */ 1178 pctl->gpio.base = -1; 1179 pctl->gpio.ngpio = pctl->data->npins; 1180 pctl->gpio.get_direction = sx150x_gpio_get_direction; 1181 pctl->gpio.direction_input = sx150x_gpio_direction_input; 1182 pctl->gpio.direction_output = sx150x_gpio_direction_output; 1183 pctl->gpio.get = sx150x_gpio_get; 1184 pctl->gpio.set = sx150x_gpio_set; 1185 pctl->gpio.set_config = gpiochip_generic_config; 1186 pctl->gpio.parent = dev; 1187 pctl->gpio.can_sleep = true; 1188 pctl->gpio.label = devm_kstrdup(dev, client->name, GFP_KERNEL); 1189 if (!pctl->gpio.label) 1190 return -ENOMEM; 1191 1192 /* 1193 * Setting multiple pins is not safe when all pins are not 1194 * handled by the same regmap register. The oscio pin (present 1195 * on the SX150X_789 chips) lives in its own register, so 1196 * would require locking that is not in place at this time. 1197 */ 1198 if (pctl->data->model != SX150X_789) 1199 pctl->gpio.set_multiple = sx150x_gpio_set_multiple; 1200 1201 /* Add Interrupt support if an irq is specified */ 1202 if (client->irq > 0) { 1203 struct gpio_irq_chip *girq; 1204 1205 pctl->irq.masked = ~0; 1206 pctl->irq.sense = 0; 1207 /* 1208 * Because sx150x_irq_threaded_fn invokes all of the 1209 * nested interrupt handlers via handle_nested_irq, 1210 * any "handler" assigned to struct gpio_irq_chip 1211 * below is going to be ignored, so the choice of the 1212 * function does not matter that much. 1213 * 1214 * We set it to handle_bad_irq to avoid confusion, 1215 * plus it will be instantly noticeable if it is ever 1216 * called (should not happen) 1217 */ 1218 girq = &pctl->gpio.irq; 1219 gpio_irq_chip_set_chip(girq, &sx150x_irq_chip); 1220 /* This will let us handle the parent IRQ in the driver */ 1221 girq->parent_handler = NULL; 1222 girq->num_parents = 0; 1223 girq->parents = NULL; 1224 girq->default_type = IRQ_TYPE_NONE; 1225 girq->handler = handle_bad_irq; 1226 girq->threaded = true; 1227 1228 ret = devm_request_threaded_irq(dev, client->irq, NULL, 1229 sx150x_irq_thread_fn, 1230 IRQF_ONESHOT | IRQF_SHARED | 1231 IRQF_TRIGGER_FALLING, 1232 client->name, pctl); 1233 if (ret < 0) 1234 return ret; 1235 } 1236 1237 ret = devm_gpiochip_add_data(dev, &pctl->gpio, pctl); 1238 if (ret) 1239 return ret; 1240 1241 /* 1242 * Pin control functions need to be enabled AFTER registering the 1243 * GPIO chip because sx150x_pinconf_set() calls 1244 * sx150x_gpio_direction_output(). 1245 */ 1246 ret = pinctrl_enable(pctl->pctldev); 1247 if (ret) { 1248 dev_err(dev, "Failed to enable pinctrl device\n"); 1249 return ret; 1250 } 1251 1252 ret = gpiochip_add_pin_range(&pctl->gpio, dev_name(dev), 1253 0, 0, pctl->data->npins); 1254 if (ret) 1255 return ret; 1256 1257 return 0; 1258 } 1259 1260 static struct i2c_driver sx150x_driver = { 1261 .driver = { 1262 .name = "sx150x-pinctrl", 1263 .of_match_table = sx150x_of_match, 1264 }, 1265 .probe = sx150x_probe, 1266 .id_table = sx150x_id, 1267 }; 1268 1269 static int __init sx150x_init(void) 1270 { 1271 return i2c_add_driver(&sx150x_driver); 1272 } 1273 subsys_initcall(sx150x_init); 1274