1 // SPDX-License-Identifier: GPL-2.0-only 2 /* 3 * Copyright (c) 2016, BayLibre, SAS. All rights reserved. 4 * Author: Neil Armstrong <narmstrong@baylibre.com> 5 * 6 * Copyright (c) 2010, Code Aurora Forum. All rights reserved. 7 * 8 * Driver for Semtech SX150X I2C GPIO Expanders 9 * The handling of the 4-bit chips (SX1501/SX1504/SX1507) is untested. 10 * 11 * Author: Gregory Bean <gbean@codeaurora.org> 12 */ 13 14 #include <linux/regmap.h> 15 #include <linux/i2c.h> 16 #include <linux/init.h> 17 #include <linux/interrupt.h> 18 #include <linux/irq.h> 19 #include <linux/mutex.h> 20 #include <linux/slab.h> 21 #include <linux/of.h> 22 #include <linux/of_device.h> 23 #include <linux/gpio/driver.h> 24 #include <linux/pinctrl/pinconf.h> 25 #include <linux/pinctrl/pinctrl.h> 26 #include <linux/pinctrl/pinmux.h> 27 #include <linux/pinctrl/pinconf-generic.h> 28 29 #include "core.h" 30 #include "pinconf.h" 31 #include "pinctrl-utils.h" 32 33 /* The chip models of sx150x */ 34 enum { 35 SX150X_123 = 0, 36 SX150X_456, 37 SX150X_789, 38 }; 39 enum { 40 SX150X_789_REG_MISC_AUTOCLEAR_OFF = 1 << 0, 41 SX150X_MAX_REGISTER = 0xad, 42 SX150X_IRQ_TYPE_EDGE_RISING = 0x1, 43 SX150X_IRQ_TYPE_EDGE_FALLING = 0x2, 44 SX150X_789_RESET_KEY1 = 0x12, 45 SX150X_789_RESET_KEY2 = 0x34, 46 }; 47 48 struct sx150x_123_pri { 49 u8 reg_pld_mode; 50 u8 reg_pld_table0; 51 u8 reg_pld_table1; 52 u8 reg_pld_table2; 53 u8 reg_pld_table3; 54 u8 reg_pld_table4; 55 u8 reg_advanced; 56 }; 57 58 struct sx150x_456_pri { 59 u8 reg_pld_mode; 60 u8 reg_pld_table0; 61 u8 reg_pld_table1; 62 u8 reg_pld_table2; 63 u8 reg_pld_table3; 64 u8 reg_pld_table4; 65 u8 reg_advanced; 66 }; 67 68 struct sx150x_789_pri { 69 u8 reg_drain; 70 u8 reg_polarity; 71 u8 reg_clock; 72 u8 reg_misc; 73 u8 reg_reset; 74 u8 ngpios; 75 }; 76 77 struct sx150x_device_data { 78 u8 model; 79 u8 reg_pullup; 80 u8 reg_pulldn; 81 u8 reg_dir; 82 u8 reg_data; 83 u8 reg_irq_mask; 84 u8 reg_irq_src; 85 u8 reg_sense; 86 u8 ngpios; 87 union { 88 struct sx150x_123_pri x123; 89 struct sx150x_456_pri x456; 90 struct sx150x_789_pri x789; 91 } pri; 92 const struct pinctrl_pin_desc *pins; 93 unsigned int npins; 94 }; 95 96 struct sx150x_pinctrl { 97 struct device *dev; 98 struct i2c_client *client; 99 struct pinctrl_dev *pctldev; 100 struct pinctrl_desc pinctrl_desc; 101 struct gpio_chip gpio; 102 struct irq_chip irq_chip; 103 struct regmap *regmap; 104 struct { 105 u32 sense; 106 u32 masked; 107 } irq; 108 struct mutex lock; 109 const struct sx150x_device_data *data; 110 }; 111 112 static const struct pinctrl_pin_desc sx150x_4_pins[] = { 113 PINCTRL_PIN(0, "gpio0"), 114 PINCTRL_PIN(1, "gpio1"), 115 PINCTRL_PIN(2, "gpio2"), 116 PINCTRL_PIN(3, "gpio3"), 117 PINCTRL_PIN(4, "oscio"), 118 }; 119 120 static const struct pinctrl_pin_desc sx150x_8_pins[] = { 121 PINCTRL_PIN(0, "gpio0"), 122 PINCTRL_PIN(1, "gpio1"), 123 PINCTRL_PIN(2, "gpio2"), 124 PINCTRL_PIN(3, "gpio3"), 125 PINCTRL_PIN(4, "gpio4"), 126 PINCTRL_PIN(5, "gpio5"), 127 PINCTRL_PIN(6, "gpio6"), 128 PINCTRL_PIN(7, "gpio7"), 129 PINCTRL_PIN(8, "oscio"), 130 }; 131 132 static const struct pinctrl_pin_desc sx150x_16_pins[] = { 133 PINCTRL_PIN(0, "gpio0"), 134 PINCTRL_PIN(1, "gpio1"), 135 PINCTRL_PIN(2, "gpio2"), 136 PINCTRL_PIN(3, "gpio3"), 137 PINCTRL_PIN(4, "gpio4"), 138 PINCTRL_PIN(5, "gpio5"), 139 PINCTRL_PIN(6, "gpio6"), 140 PINCTRL_PIN(7, "gpio7"), 141 PINCTRL_PIN(8, "gpio8"), 142 PINCTRL_PIN(9, "gpio9"), 143 PINCTRL_PIN(10, "gpio10"), 144 PINCTRL_PIN(11, "gpio11"), 145 PINCTRL_PIN(12, "gpio12"), 146 PINCTRL_PIN(13, "gpio13"), 147 PINCTRL_PIN(14, "gpio14"), 148 PINCTRL_PIN(15, "gpio15"), 149 PINCTRL_PIN(16, "oscio"), 150 }; 151 152 static const struct sx150x_device_data sx1501q_device_data = { 153 .model = SX150X_123, 154 .reg_pullup = 0x02, 155 .reg_pulldn = 0x03, 156 .reg_dir = 0x01, 157 .reg_data = 0x00, 158 .reg_irq_mask = 0x05, 159 .reg_irq_src = 0x08, 160 .reg_sense = 0x07, 161 .pri.x123 = { 162 .reg_pld_mode = 0x10, 163 .reg_pld_table0 = 0x11, 164 .reg_pld_table2 = 0x13, 165 .reg_advanced = 0xad, 166 }, 167 .ngpios = 4, 168 .pins = sx150x_4_pins, 169 .npins = 4, /* oscio not available */ 170 }; 171 172 static const struct sx150x_device_data sx1502q_device_data = { 173 .model = SX150X_123, 174 .reg_pullup = 0x02, 175 .reg_pulldn = 0x03, 176 .reg_dir = 0x01, 177 .reg_data = 0x00, 178 .reg_irq_mask = 0x05, 179 .reg_irq_src = 0x08, 180 .reg_sense = 0x06, 181 .pri.x123 = { 182 .reg_pld_mode = 0x10, 183 .reg_pld_table0 = 0x11, 184 .reg_pld_table1 = 0x12, 185 .reg_pld_table2 = 0x13, 186 .reg_pld_table3 = 0x14, 187 .reg_pld_table4 = 0x15, 188 .reg_advanced = 0xad, 189 }, 190 .ngpios = 8, 191 .pins = sx150x_8_pins, 192 .npins = 8, /* oscio not available */ 193 }; 194 195 static const struct sx150x_device_data sx1503q_device_data = { 196 .model = SX150X_123, 197 .reg_pullup = 0x04, 198 .reg_pulldn = 0x06, 199 .reg_dir = 0x02, 200 .reg_data = 0x00, 201 .reg_irq_mask = 0x08, 202 .reg_irq_src = 0x0e, 203 .reg_sense = 0x0a, 204 .pri.x123 = { 205 .reg_pld_mode = 0x20, 206 .reg_pld_table0 = 0x22, 207 .reg_pld_table1 = 0x24, 208 .reg_pld_table2 = 0x26, 209 .reg_pld_table3 = 0x28, 210 .reg_pld_table4 = 0x2a, 211 .reg_advanced = 0xad, 212 }, 213 .ngpios = 16, 214 .pins = sx150x_16_pins, 215 .npins = 16, /* oscio not available */ 216 }; 217 218 static const struct sx150x_device_data sx1504q_device_data = { 219 .model = SX150X_456, 220 .reg_pullup = 0x02, 221 .reg_pulldn = 0x03, 222 .reg_dir = 0x01, 223 .reg_data = 0x00, 224 .reg_irq_mask = 0x05, 225 .reg_irq_src = 0x08, 226 .reg_sense = 0x07, 227 .pri.x456 = { 228 .reg_pld_mode = 0x10, 229 .reg_pld_table0 = 0x11, 230 .reg_pld_table2 = 0x13, 231 }, 232 .ngpios = 4, 233 .pins = sx150x_4_pins, 234 .npins = 4, /* oscio not available */ 235 }; 236 237 static const struct sx150x_device_data sx1505q_device_data = { 238 .model = SX150X_456, 239 .reg_pullup = 0x02, 240 .reg_pulldn = 0x03, 241 .reg_dir = 0x01, 242 .reg_data = 0x00, 243 .reg_irq_mask = 0x05, 244 .reg_irq_src = 0x08, 245 .reg_sense = 0x06, 246 .pri.x456 = { 247 .reg_pld_mode = 0x10, 248 .reg_pld_table0 = 0x11, 249 .reg_pld_table1 = 0x12, 250 .reg_pld_table2 = 0x13, 251 .reg_pld_table3 = 0x14, 252 .reg_pld_table4 = 0x15, 253 }, 254 .ngpios = 8, 255 .pins = sx150x_8_pins, 256 .npins = 8, /* oscio not available */ 257 }; 258 259 static const struct sx150x_device_data sx1506q_device_data = { 260 .model = SX150X_456, 261 .reg_pullup = 0x04, 262 .reg_pulldn = 0x06, 263 .reg_dir = 0x02, 264 .reg_data = 0x00, 265 .reg_irq_mask = 0x08, 266 .reg_irq_src = 0x0e, 267 .reg_sense = 0x0a, 268 .pri.x456 = { 269 .reg_pld_mode = 0x20, 270 .reg_pld_table0 = 0x22, 271 .reg_pld_table1 = 0x24, 272 .reg_pld_table2 = 0x26, 273 .reg_pld_table3 = 0x28, 274 .reg_pld_table4 = 0x2a, 275 .reg_advanced = 0xad, 276 }, 277 .ngpios = 16, 278 .pins = sx150x_16_pins, 279 .npins = 16, /* oscio not available */ 280 }; 281 282 static const struct sx150x_device_data sx1507q_device_data = { 283 .model = SX150X_789, 284 .reg_pullup = 0x03, 285 .reg_pulldn = 0x04, 286 .reg_dir = 0x07, 287 .reg_data = 0x08, 288 .reg_irq_mask = 0x09, 289 .reg_irq_src = 0x0b, 290 .reg_sense = 0x0a, 291 .pri.x789 = { 292 .reg_drain = 0x05, 293 .reg_polarity = 0x06, 294 .reg_clock = 0x0d, 295 .reg_misc = 0x0e, 296 .reg_reset = 0x7d, 297 }, 298 .ngpios = 4, 299 .pins = sx150x_4_pins, 300 .npins = ARRAY_SIZE(sx150x_4_pins), 301 }; 302 303 static const struct sx150x_device_data sx1508q_device_data = { 304 .model = SX150X_789, 305 .reg_pullup = 0x03, 306 .reg_pulldn = 0x04, 307 .reg_dir = 0x07, 308 .reg_data = 0x08, 309 .reg_irq_mask = 0x09, 310 .reg_irq_src = 0x0c, 311 .reg_sense = 0x0a, 312 .pri.x789 = { 313 .reg_drain = 0x05, 314 .reg_polarity = 0x06, 315 .reg_clock = 0x0f, 316 .reg_misc = 0x10, 317 .reg_reset = 0x7d, 318 }, 319 .ngpios = 8, 320 .pins = sx150x_8_pins, 321 .npins = ARRAY_SIZE(sx150x_8_pins), 322 }; 323 324 static const struct sx150x_device_data sx1509q_device_data = { 325 .model = SX150X_789, 326 .reg_pullup = 0x06, 327 .reg_pulldn = 0x08, 328 .reg_dir = 0x0e, 329 .reg_data = 0x10, 330 .reg_irq_mask = 0x12, 331 .reg_irq_src = 0x18, 332 .reg_sense = 0x14, 333 .pri.x789 = { 334 .reg_drain = 0x0a, 335 .reg_polarity = 0x0c, 336 .reg_clock = 0x1e, 337 .reg_misc = 0x1f, 338 .reg_reset = 0x7d, 339 }, 340 .ngpios = 16, 341 .pins = sx150x_16_pins, 342 .npins = ARRAY_SIZE(sx150x_16_pins), 343 }; 344 345 static int sx150x_pinctrl_get_groups_count(struct pinctrl_dev *pctldev) 346 { 347 return 0; 348 } 349 350 static const char *sx150x_pinctrl_get_group_name(struct pinctrl_dev *pctldev, 351 unsigned int group) 352 { 353 return NULL; 354 } 355 356 static int sx150x_pinctrl_get_group_pins(struct pinctrl_dev *pctldev, 357 unsigned int group, 358 const unsigned int **pins, 359 unsigned int *num_pins) 360 { 361 return -ENOTSUPP; 362 } 363 364 static const struct pinctrl_ops sx150x_pinctrl_ops = { 365 .get_groups_count = sx150x_pinctrl_get_groups_count, 366 .get_group_name = sx150x_pinctrl_get_group_name, 367 .get_group_pins = sx150x_pinctrl_get_group_pins, 368 #ifdef CONFIG_OF 369 .dt_node_to_map = pinconf_generic_dt_node_to_map_pin, 370 .dt_free_map = pinctrl_utils_free_map, 371 #endif 372 }; 373 374 static bool sx150x_pin_is_oscio(struct sx150x_pinctrl *pctl, unsigned int pin) 375 { 376 if (pin >= pctl->data->npins) 377 return false; 378 379 /* OSCIO pin is only present in 789 devices */ 380 if (pctl->data->model != SX150X_789) 381 return false; 382 383 return !strcmp(pctl->data->pins[pin].name, "oscio"); 384 } 385 386 static int sx150x_gpio_get_direction(struct gpio_chip *chip, 387 unsigned int offset) 388 { 389 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 390 unsigned int value; 391 int ret; 392 393 if (sx150x_pin_is_oscio(pctl, offset)) 394 return GPIO_LINE_DIRECTION_OUT; 395 396 ret = regmap_read(pctl->regmap, pctl->data->reg_dir, &value); 397 if (ret < 0) 398 return ret; 399 400 if (value & BIT(offset)) 401 return GPIO_LINE_DIRECTION_IN; 402 403 return GPIO_LINE_DIRECTION_OUT; 404 } 405 406 static int sx150x_gpio_get(struct gpio_chip *chip, unsigned int offset) 407 { 408 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 409 unsigned int value; 410 int ret; 411 412 if (sx150x_pin_is_oscio(pctl, offset)) 413 return -EINVAL; 414 415 ret = regmap_read(pctl->regmap, pctl->data->reg_data, &value); 416 if (ret < 0) 417 return ret; 418 419 return !!(value & BIT(offset)); 420 } 421 422 static int __sx150x_gpio_set(struct sx150x_pinctrl *pctl, unsigned int offset, 423 int value) 424 { 425 return regmap_write_bits(pctl->regmap, pctl->data->reg_data, 426 BIT(offset), value ? BIT(offset) : 0); 427 } 428 429 static int sx150x_gpio_oscio_set(struct sx150x_pinctrl *pctl, 430 int value) 431 { 432 return regmap_write(pctl->regmap, 433 pctl->data->pri.x789.reg_clock, 434 (value ? 0x1f : 0x10)); 435 } 436 437 static void sx150x_gpio_set(struct gpio_chip *chip, unsigned int offset, 438 int value) 439 { 440 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 441 442 if (sx150x_pin_is_oscio(pctl, offset)) 443 sx150x_gpio_oscio_set(pctl, value); 444 else 445 __sx150x_gpio_set(pctl, offset, value); 446 447 } 448 449 static void sx150x_gpio_set_multiple(struct gpio_chip *chip, 450 unsigned long *mask, 451 unsigned long *bits) 452 { 453 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 454 455 regmap_write_bits(pctl->regmap, pctl->data->reg_data, *mask, *bits); 456 } 457 458 static int sx150x_gpio_direction_input(struct gpio_chip *chip, 459 unsigned int offset) 460 { 461 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 462 463 if (sx150x_pin_is_oscio(pctl, offset)) 464 return -EINVAL; 465 466 return regmap_write_bits(pctl->regmap, 467 pctl->data->reg_dir, 468 BIT(offset), BIT(offset)); 469 } 470 471 static int sx150x_gpio_direction_output(struct gpio_chip *chip, 472 unsigned int offset, int value) 473 { 474 struct sx150x_pinctrl *pctl = gpiochip_get_data(chip); 475 int ret; 476 477 if (sx150x_pin_is_oscio(pctl, offset)) 478 return sx150x_gpio_oscio_set(pctl, value); 479 480 ret = __sx150x_gpio_set(pctl, offset, value); 481 if (ret < 0) 482 return ret; 483 484 return regmap_write_bits(pctl->regmap, 485 pctl->data->reg_dir, 486 BIT(offset), 0); 487 } 488 489 static void sx150x_irq_mask(struct irq_data *d) 490 { 491 struct sx150x_pinctrl *pctl = 492 gpiochip_get_data(irq_data_get_irq_chip_data(d)); 493 unsigned int n = d->hwirq; 494 495 pctl->irq.masked |= BIT(n); 496 } 497 498 static void sx150x_irq_unmask(struct irq_data *d) 499 { 500 struct sx150x_pinctrl *pctl = 501 gpiochip_get_data(irq_data_get_irq_chip_data(d)); 502 unsigned int n = d->hwirq; 503 504 pctl->irq.masked &= ~BIT(n); 505 } 506 507 static void sx150x_irq_set_sense(struct sx150x_pinctrl *pctl, 508 unsigned int line, unsigned int sense) 509 { 510 /* 511 * Every interrupt line is represented by two bits shifted 512 * proportionally to the line number 513 */ 514 const unsigned int n = line * 2; 515 const unsigned int mask = ~((SX150X_IRQ_TYPE_EDGE_RISING | 516 SX150X_IRQ_TYPE_EDGE_FALLING) << n); 517 518 pctl->irq.sense &= mask; 519 pctl->irq.sense |= sense << n; 520 } 521 522 static int sx150x_irq_set_type(struct irq_data *d, unsigned int flow_type) 523 { 524 struct sx150x_pinctrl *pctl = 525 gpiochip_get_data(irq_data_get_irq_chip_data(d)); 526 unsigned int n, val = 0; 527 528 if (flow_type & (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW)) 529 return -EINVAL; 530 531 n = d->hwirq; 532 533 if (flow_type & IRQ_TYPE_EDGE_RISING) 534 val |= SX150X_IRQ_TYPE_EDGE_RISING; 535 if (flow_type & IRQ_TYPE_EDGE_FALLING) 536 val |= SX150X_IRQ_TYPE_EDGE_FALLING; 537 538 sx150x_irq_set_sense(pctl, n, val); 539 return 0; 540 } 541 542 static irqreturn_t sx150x_irq_thread_fn(int irq, void *dev_id) 543 { 544 struct sx150x_pinctrl *pctl = (struct sx150x_pinctrl *)dev_id; 545 unsigned long n, status; 546 unsigned int val; 547 int err; 548 549 err = regmap_read(pctl->regmap, pctl->data->reg_irq_src, &val); 550 if (err < 0) 551 return IRQ_NONE; 552 553 err = regmap_write(pctl->regmap, pctl->data->reg_irq_src, val); 554 if (err < 0) 555 return IRQ_NONE; 556 557 status = val; 558 for_each_set_bit(n, &status, pctl->data->ngpios) 559 handle_nested_irq(irq_find_mapping(pctl->gpio.irq.domain, n)); 560 561 return IRQ_HANDLED; 562 } 563 564 static void sx150x_irq_bus_lock(struct irq_data *d) 565 { 566 struct sx150x_pinctrl *pctl = 567 gpiochip_get_data(irq_data_get_irq_chip_data(d)); 568 569 mutex_lock(&pctl->lock); 570 } 571 572 static void sx150x_irq_bus_sync_unlock(struct irq_data *d) 573 { 574 struct sx150x_pinctrl *pctl = 575 gpiochip_get_data(irq_data_get_irq_chip_data(d)); 576 577 regmap_write(pctl->regmap, pctl->data->reg_irq_mask, pctl->irq.masked); 578 regmap_write(pctl->regmap, pctl->data->reg_sense, pctl->irq.sense); 579 mutex_unlock(&pctl->lock); 580 } 581 582 static int sx150x_pinconf_get(struct pinctrl_dev *pctldev, unsigned int pin, 583 unsigned long *config) 584 { 585 struct sx150x_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev); 586 unsigned int param = pinconf_to_config_param(*config); 587 int ret; 588 u32 arg; 589 unsigned int data; 590 591 if (sx150x_pin_is_oscio(pctl, pin)) { 592 switch (param) { 593 case PIN_CONFIG_DRIVE_PUSH_PULL: 594 case PIN_CONFIG_OUTPUT: 595 ret = regmap_read(pctl->regmap, 596 pctl->data->pri.x789.reg_clock, 597 &data); 598 if (ret < 0) 599 return ret; 600 601 if (param == PIN_CONFIG_DRIVE_PUSH_PULL) 602 arg = (data & 0x1f) ? 1 : 0; 603 else { 604 if ((data & 0x1f) == 0x1f) 605 arg = 1; 606 else if ((data & 0x1f) == 0x10) 607 arg = 0; 608 else 609 return -EINVAL; 610 } 611 612 break; 613 default: 614 return -ENOTSUPP; 615 } 616 617 goto out; 618 } 619 620 switch (param) { 621 case PIN_CONFIG_BIAS_PULL_DOWN: 622 ret = regmap_read(pctl->regmap, 623 pctl->data->reg_pulldn, 624 &data); 625 data &= BIT(pin); 626 627 if (ret < 0) 628 return ret; 629 630 if (!ret) 631 return -EINVAL; 632 633 arg = 1; 634 break; 635 636 case PIN_CONFIG_BIAS_PULL_UP: 637 ret = regmap_read(pctl->regmap, 638 pctl->data->reg_pullup, 639 &data); 640 data &= BIT(pin); 641 642 if (ret < 0) 643 return ret; 644 645 if (!ret) 646 return -EINVAL; 647 648 arg = 1; 649 break; 650 651 case PIN_CONFIG_DRIVE_OPEN_DRAIN: 652 if (pctl->data->model != SX150X_789) 653 return -ENOTSUPP; 654 655 ret = regmap_read(pctl->regmap, 656 pctl->data->pri.x789.reg_drain, 657 &data); 658 data &= BIT(pin); 659 660 if (ret < 0) 661 return ret; 662 663 if (!data) 664 return -EINVAL; 665 666 arg = 1; 667 break; 668 669 case PIN_CONFIG_DRIVE_PUSH_PULL: 670 if (pctl->data->model != SX150X_789) 671 arg = true; 672 else { 673 ret = regmap_read(pctl->regmap, 674 pctl->data->pri.x789.reg_drain, 675 &data); 676 data &= BIT(pin); 677 678 if (ret < 0) 679 return ret; 680 681 if (data) 682 return -EINVAL; 683 684 arg = 1; 685 } 686 break; 687 688 case PIN_CONFIG_OUTPUT: 689 ret = sx150x_gpio_get_direction(&pctl->gpio, pin); 690 if (ret < 0) 691 return ret; 692 693 if (ret == GPIO_LINE_DIRECTION_IN) 694 return -EINVAL; 695 696 ret = sx150x_gpio_get(&pctl->gpio, pin); 697 if (ret < 0) 698 return ret; 699 700 arg = ret; 701 break; 702 703 default: 704 return -ENOTSUPP; 705 } 706 707 out: 708 *config = pinconf_to_config_packed(param, arg); 709 710 return 0; 711 } 712 713 static int sx150x_pinconf_set(struct pinctrl_dev *pctldev, unsigned int pin, 714 unsigned long *configs, unsigned int num_configs) 715 { 716 struct sx150x_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev); 717 enum pin_config_param param; 718 u32 arg; 719 int i; 720 int ret; 721 722 for (i = 0; i < num_configs; i++) { 723 param = pinconf_to_config_param(configs[i]); 724 arg = pinconf_to_config_argument(configs[i]); 725 726 if (sx150x_pin_is_oscio(pctl, pin)) { 727 if (param == PIN_CONFIG_OUTPUT) { 728 ret = sx150x_gpio_direction_output(&pctl->gpio, 729 pin, arg); 730 if (ret < 0) 731 return ret; 732 733 continue; 734 } else 735 return -ENOTSUPP; 736 } 737 738 switch (param) { 739 case PIN_CONFIG_BIAS_PULL_PIN_DEFAULT: 740 case PIN_CONFIG_BIAS_DISABLE: 741 ret = regmap_write_bits(pctl->regmap, 742 pctl->data->reg_pulldn, 743 BIT(pin), 0); 744 if (ret < 0) 745 return ret; 746 747 ret = regmap_write_bits(pctl->regmap, 748 pctl->data->reg_pullup, 749 BIT(pin), 0); 750 if (ret < 0) 751 return ret; 752 753 break; 754 755 case PIN_CONFIG_BIAS_PULL_UP: 756 ret = regmap_write_bits(pctl->regmap, 757 pctl->data->reg_pullup, 758 BIT(pin), BIT(pin)); 759 if (ret < 0) 760 return ret; 761 762 break; 763 764 case PIN_CONFIG_BIAS_PULL_DOWN: 765 ret = regmap_write_bits(pctl->regmap, 766 pctl->data->reg_pulldn, 767 BIT(pin), BIT(pin)); 768 if (ret < 0) 769 return ret; 770 771 break; 772 773 case PIN_CONFIG_DRIVE_OPEN_DRAIN: 774 if (pctl->data->model != SX150X_789 || 775 sx150x_pin_is_oscio(pctl, pin)) 776 return -ENOTSUPP; 777 778 ret = regmap_write_bits(pctl->regmap, 779 pctl->data->pri.x789.reg_drain, 780 BIT(pin), BIT(pin)); 781 if (ret < 0) 782 return ret; 783 784 break; 785 786 case PIN_CONFIG_DRIVE_PUSH_PULL: 787 if (pctl->data->model != SX150X_789 || 788 sx150x_pin_is_oscio(pctl, pin)) 789 return 0; 790 791 ret = regmap_write_bits(pctl->regmap, 792 pctl->data->pri.x789.reg_drain, 793 BIT(pin), 0); 794 if (ret < 0) 795 return ret; 796 797 break; 798 799 case PIN_CONFIG_OUTPUT: 800 ret = sx150x_gpio_direction_output(&pctl->gpio, 801 pin, arg); 802 if (ret < 0) 803 return ret; 804 805 break; 806 807 default: 808 return -ENOTSUPP; 809 } 810 } /* for each config */ 811 812 return 0; 813 } 814 815 static const struct pinconf_ops sx150x_pinconf_ops = { 816 .pin_config_get = sx150x_pinconf_get, 817 .pin_config_set = sx150x_pinconf_set, 818 .is_generic = true, 819 }; 820 821 static const struct i2c_device_id sx150x_id[] = { 822 {"sx1501q", (kernel_ulong_t) &sx1501q_device_data }, 823 {"sx1502q", (kernel_ulong_t) &sx1502q_device_data }, 824 {"sx1503q", (kernel_ulong_t) &sx1503q_device_data }, 825 {"sx1504q", (kernel_ulong_t) &sx1504q_device_data }, 826 {"sx1505q", (kernel_ulong_t) &sx1505q_device_data }, 827 {"sx1506q", (kernel_ulong_t) &sx1506q_device_data }, 828 {"sx1507q", (kernel_ulong_t) &sx1507q_device_data }, 829 {"sx1508q", (kernel_ulong_t) &sx1508q_device_data }, 830 {"sx1509q", (kernel_ulong_t) &sx1509q_device_data }, 831 {} 832 }; 833 834 static const struct of_device_id sx150x_of_match[] = { 835 { .compatible = "semtech,sx1501q", .data = &sx1501q_device_data }, 836 { .compatible = "semtech,sx1502q", .data = &sx1502q_device_data }, 837 { .compatible = "semtech,sx1503q", .data = &sx1503q_device_data }, 838 { .compatible = "semtech,sx1504q", .data = &sx1504q_device_data }, 839 { .compatible = "semtech,sx1505q", .data = &sx1505q_device_data }, 840 { .compatible = "semtech,sx1506q", .data = &sx1506q_device_data }, 841 { .compatible = "semtech,sx1507q", .data = &sx1507q_device_data }, 842 { .compatible = "semtech,sx1508q", .data = &sx1508q_device_data }, 843 { .compatible = "semtech,sx1509q", .data = &sx1509q_device_data }, 844 {}, 845 }; 846 847 static int sx150x_reset(struct sx150x_pinctrl *pctl) 848 { 849 int err; 850 851 err = i2c_smbus_write_byte_data(pctl->client, 852 pctl->data->pri.x789.reg_reset, 853 SX150X_789_RESET_KEY1); 854 if (err < 0) 855 return err; 856 857 err = i2c_smbus_write_byte_data(pctl->client, 858 pctl->data->pri.x789.reg_reset, 859 SX150X_789_RESET_KEY2); 860 return err; 861 } 862 863 static int sx150x_init_misc(struct sx150x_pinctrl *pctl) 864 { 865 u8 reg, value; 866 867 switch (pctl->data->model) { 868 case SX150X_789: 869 reg = pctl->data->pri.x789.reg_misc; 870 value = SX150X_789_REG_MISC_AUTOCLEAR_OFF; 871 break; 872 case SX150X_456: 873 reg = pctl->data->pri.x456.reg_advanced; 874 value = 0x00; 875 876 /* 877 * Only SX1506 has RegAdvanced, SX1504/5 are expected 878 * to initialize this offset to zero 879 */ 880 if (!reg) 881 return 0; 882 break; 883 case SX150X_123: 884 reg = pctl->data->pri.x123.reg_advanced; 885 value = 0x00; 886 break; 887 default: 888 WARN(1, "Unknown chip model %d\n", pctl->data->model); 889 return -EINVAL; 890 } 891 892 return regmap_write(pctl->regmap, reg, value); 893 } 894 895 static int sx150x_init_hw(struct sx150x_pinctrl *pctl) 896 { 897 const u8 reg[] = { 898 [SX150X_789] = pctl->data->pri.x789.reg_polarity, 899 [SX150X_456] = pctl->data->pri.x456.reg_pld_mode, 900 [SX150X_123] = pctl->data->pri.x123.reg_pld_mode, 901 }; 902 int err; 903 904 if (pctl->data->model == SX150X_789 && 905 of_property_read_bool(pctl->dev->of_node, "semtech,probe-reset")) { 906 err = sx150x_reset(pctl); 907 if (err < 0) 908 return err; 909 } 910 911 err = sx150x_init_misc(pctl); 912 if (err < 0) 913 return err; 914 915 /* Set all pins to work in normal mode */ 916 return regmap_write(pctl->regmap, reg[pctl->data->model], 0); 917 } 918 919 static int sx150x_regmap_reg_width(struct sx150x_pinctrl *pctl, 920 unsigned int reg) 921 { 922 const struct sx150x_device_data *data = pctl->data; 923 924 if (reg == data->reg_sense) { 925 /* 926 * RegSense packs two bits of configuration per GPIO, 927 * so we'd need to read twice as many bits as there 928 * are GPIO in our chip 929 */ 930 return 2 * data->ngpios; 931 } else if ((data->model == SX150X_789 && 932 (reg == data->pri.x789.reg_misc || 933 reg == data->pri.x789.reg_clock || 934 reg == data->pri.x789.reg_reset)) 935 || 936 (data->model == SX150X_123 && 937 reg == data->pri.x123.reg_advanced) 938 || 939 (data->model == SX150X_456 && 940 data->pri.x456.reg_advanced && 941 reg == data->pri.x456.reg_advanced)) { 942 return 8; 943 } else { 944 return data->ngpios; 945 } 946 } 947 948 static unsigned int sx150x_maybe_swizzle(struct sx150x_pinctrl *pctl, 949 unsigned int reg, unsigned int val) 950 { 951 unsigned int a, b; 952 const struct sx150x_device_data *data = pctl->data; 953 954 /* 955 * Whereas SX1509 presents RegSense in a simple layout as such: 956 * reg [ f f e e d d c c ] 957 * reg + 1 [ b b a a 9 9 8 8 ] 958 * reg + 2 [ 7 7 6 6 5 5 4 4 ] 959 * reg + 3 [ 3 3 2 2 1 1 0 0 ] 960 * 961 * SX1503 and SX1506 deviate from that data layout, instead storing 962 * their contents as follows: 963 * 964 * reg [ f f e e d d c c ] 965 * reg + 1 [ 7 7 6 6 5 5 4 4 ] 966 * reg + 2 [ b b a a 9 9 8 8 ] 967 * reg + 3 [ 3 3 2 2 1 1 0 0 ] 968 * 969 * so, taking that into account, we swap two 970 * inner bytes of a 4-byte result 971 */ 972 973 if (reg == data->reg_sense && 974 data->ngpios == 16 && 975 (data->model == SX150X_123 || 976 data->model == SX150X_456)) { 977 a = val & 0x00ff0000; 978 b = val & 0x0000ff00; 979 980 val &= 0xff0000ff; 981 val |= b << 8; 982 val |= a >> 8; 983 } 984 985 return val; 986 } 987 988 /* 989 * In order to mask the differences between 16 and 8 bit expander 990 * devices we set up a sligthly ficticious regmap that pretends to be 991 * a set of 32-bit (to accommodate RegSenseLow/RegSenseHigh 992 * pair/quartet) registers and transparently reconstructs those 993 * registers via multiple I2C/SMBus reads 994 * 995 * This way the rest of the driver code, interfacing with the chip via 996 * regmap API, can work assuming that each GPIO pin is represented by 997 * a group of bits at an offset proportional to GPIO number within a 998 * given register. 999 */ 1000 static int sx150x_regmap_reg_read(void *context, unsigned int reg, 1001 unsigned int *result) 1002 { 1003 int ret, n; 1004 struct sx150x_pinctrl *pctl = context; 1005 struct i2c_client *i2c = pctl->client; 1006 const int width = sx150x_regmap_reg_width(pctl, reg); 1007 unsigned int idx, val; 1008 1009 /* 1010 * There are four potential cases covered by this function: 1011 * 1012 * 1) 8-pin chip, single configuration bit register 1013 * 1014 * This is trivial the code below just needs to read: 1015 * reg [ 7 6 5 4 3 2 1 0 ] 1016 * 1017 * 2) 8-pin chip, double configuration bit register (RegSense) 1018 * 1019 * The read will be done as follows: 1020 * reg [ 7 7 6 6 5 5 4 4 ] 1021 * reg + 1 [ 3 3 2 2 1 1 0 0 ] 1022 * 1023 * 3) 16-pin chip, single configuration bit register 1024 * 1025 * The read will be done as follows: 1026 * reg [ f e d c b a 9 8 ] 1027 * reg + 1 [ 7 6 5 4 3 2 1 0 ] 1028 * 1029 * 4) 16-pin chip, double configuration bit register (RegSense) 1030 * 1031 * The read will be done as follows: 1032 * reg [ f f e e d d c c ] 1033 * reg + 1 [ b b a a 9 9 8 8 ] 1034 * reg + 2 [ 7 7 6 6 5 5 4 4 ] 1035 * reg + 3 [ 3 3 2 2 1 1 0 0 ] 1036 */ 1037 1038 for (n = width, val = 0, idx = reg; n > 0; n -= 8, idx++) { 1039 val <<= 8; 1040 1041 ret = i2c_smbus_read_byte_data(i2c, idx); 1042 if (ret < 0) 1043 return ret; 1044 1045 val |= ret; 1046 } 1047 1048 *result = sx150x_maybe_swizzle(pctl, reg, val); 1049 1050 return 0; 1051 } 1052 1053 static int sx150x_regmap_reg_write(void *context, unsigned int reg, 1054 unsigned int val) 1055 { 1056 int ret, n; 1057 struct sx150x_pinctrl *pctl = context; 1058 struct i2c_client *i2c = pctl->client; 1059 const int width = sx150x_regmap_reg_width(pctl, reg); 1060 1061 val = sx150x_maybe_swizzle(pctl, reg, val); 1062 1063 n = (width - 1) & ~7; 1064 do { 1065 const u8 byte = (val >> n) & 0xff; 1066 1067 ret = i2c_smbus_write_byte_data(i2c, reg, byte); 1068 if (ret < 0) 1069 return ret; 1070 1071 reg++; 1072 n -= 8; 1073 } while (n >= 0); 1074 1075 return 0; 1076 } 1077 1078 static bool sx150x_reg_volatile(struct device *dev, unsigned int reg) 1079 { 1080 struct sx150x_pinctrl *pctl = i2c_get_clientdata(to_i2c_client(dev)); 1081 1082 return reg == pctl->data->reg_irq_src || reg == pctl->data->reg_data; 1083 } 1084 1085 static const struct regmap_config sx150x_regmap_config = { 1086 .reg_bits = 8, 1087 .val_bits = 32, 1088 1089 .cache_type = REGCACHE_RBTREE, 1090 1091 .reg_read = sx150x_regmap_reg_read, 1092 .reg_write = sx150x_regmap_reg_write, 1093 1094 .max_register = SX150X_MAX_REGISTER, 1095 .volatile_reg = sx150x_reg_volatile, 1096 }; 1097 1098 static int sx150x_probe(struct i2c_client *client, 1099 const struct i2c_device_id *id) 1100 { 1101 static const u32 i2c_funcs = I2C_FUNC_SMBUS_BYTE_DATA | 1102 I2C_FUNC_SMBUS_WRITE_WORD_DATA; 1103 struct device *dev = &client->dev; 1104 struct sx150x_pinctrl *pctl; 1105 int ret; 1106 1107 if (!i2c_check_functionality(client->adapter, i2c_funcs)) 1108 return -ENOSYS; 1109 1110 pctl = devm_kzalloc(dev, sizeof(*pctl), GFP_KERNEL); 1111 if (!pctl) 1112 return -ENOMEM; 1113 1114 i2c_set_clientdata(client, pctl); 1115 1116 pctl->dev = dev; 1117 pctl->client = client; 1118 1119 if (dev->of_node) 1120 pctl->data = of_device_get_match_data(dev); 1121 else 1122 pctl->data = (struct sx150x_device_data *)id->driver_data; 1123 1124 if (!pctl->data) 1125 return -EINVAL; 1126 1127 pctl->regmap = devm_regmap_init(dev, NULL, pctl, 1128 &sx150x_regmap_config); 1129 if (IS_ERR(pctl->regmap)) { 1130 ret = PTR_ERR(pctl->regmap); 1131 dev_err(dev, "Failed to allocate register map: %d\n", 1132 ret); 1133 return ret; 1134 } 1135 1136 mutex_init(&pctl->lock); 1137 1138 ret = sx150x_init_hw(pctl); 1139 if (ret) 1140 return ret; 1141 1142 /* Pinctrl_desc */ 1143 pctl->pinctrl_desc.name = "sx150x-pinctrl"; 1144 pctl->pinctrl_desc.pctlops = &sx150x_pinctrl_ops; 1145 pctl->pinctrl_desc.confops = &sx150x_pinconf_ops; 1146 pctl->pinctrl_desc.pins = pctl->data->pins; 1147 pctl->pinctrl_desc.npins = pctl->data->npins; 1148 pctl->pinctrl_desc.owner = THIS_MODULE; 1149 1150 ret = devm_pinctrl_register_and_init(dev, &pctl->pinctrl_desc, 1151 pctl, &pctl->pctldev); 1152 if (ret) { 1153 dev_err(dev, "Failed to register pinctrl device\n"); 1154 return ret; 1155 } 1156 1157 ret = pinctrl_enable(pctl->pctldev); 1158 if (ret) { 1159 dev_err(dev, "Failed to enable pinctrl device\n"); 1160 return ret; 1161 } 1162 1163 /* Register GPIO controller */ 1164 pctl->gpio.base = -1; 1165 pctl->gpio.ngpio = pctl->data->npins; 1166 pctl->gpio.get_direction = sx150x_gpio_get_direction; 1167 pctl->gpio.direction_input = sx150x_gpio_direction_input; 1168 pctl->gpio.direction_output = sx150x_gpio_direction_output; 1169 pctl->gpio.get = sx150x_gpio_get; 1170 pctl->gpio.set = sx150x_gpio_set; 1171 pctl->gpio.set_config = gpiochip_generic_config; 1172 pctl->gpio.parent = dev; 1173 #ifdef CONFIG_OF_GPIO 1174 pctl->gpio.of_node = dev->of_node; 1175 #endif 1176 pctl->gpio.can_sleep = true; 1177 pctl->gpio.label = devm_kstrdup(dev, client->name, GFP_KERNEL); 1178 if (!pctl->gpio.label) 1179 return -ENOMEM; 1180 1181 /* 1182 * Setting multiple pins is not safe when all pins are not 1183 * handled by the same regmap register. The oscio pin (present 1184 * on the SX150X_789 chips) lives in its own register, so 1185 * would require locking that is not in place at this time. 1186 */ 1187 if (pctl->data->model != SX150X_789) 1188 pctl->gpio.set_multiple = sx150x_gpio_set_multiple; 1189 1190 /* Add Interrupt support if an irq is specified */ 1191 if (client->irq > 0) { 1192 struct gpio_irq_chip *girq; 1193 1194 pctl->irq_chip.irq_mask = sx150x_irq_mask; 1195 pctl->irq_chip.irq_unmask = sx150x_irq_unmask; 1196 pctl->irq_chip.irq_set_type = sx150x_irq_set_type; 1197 pctl->irq_chip.irq_bus_lock = sx150x_irq_bus_lock; 1198 pctl->irq_chip.irq_bus_sync_unlock = sx150x_irq_bus_sync_unlock; 1199 pctl->irq_chip.name = devm_kstrdup(dev, client->name, 1200 GFP_KERNEL); 1201 if (!pctl->irq_chip.name) 1202 return -ENOMEM; 1203 1204 pctl->irq.masked = ~0; 1205 pctl->irq.sense = 0; 1206 1207 /* 1208 * Because sx150x_irq_threaded_fn invokes all of the 1209 * nested interrupt handlers via handle_nested_irq, 1210 * any "handler" assigned to struct gpio_irq_chip 1211 * below is going to be ignored, so the choice of the 1212 * function does not matter that much. 1213 * 1214 * We set it to handle_bad_irq to avoid confusion, 1215 * plus it will be instantly noticeable if it is ever 1216 * called (should not happen) 1217 */ 1218 girq = &pctl->gpio.irq; 1219 girq->chip = &pctl->irq_chip; 1220 /* This will let us handle the parent IRQ in the driver */ 1221 girq->parent_handler = NULL; 1222 girq->num_parents = 0; 1223 girq->parents = NULL; 1224 girq->default_type = IRQ_TYPE_NONE; 1225 girq->handler = handle_bad_irq; 1226 girq->threaded = true; 1227 1228 ret = devm_request_threaded_irq(dev, client->irq, NULL, 1229 sx150x_irq_thread_fn, 1230 IRQF_ONESHOT | IRQF_SHARED | 1231 IRQF_TRIGGER_FALLING, 1232 pctl->irq_chip.name, pctl); 1233 if (ret < 0) 1234 return ret; 1235 } 1236 1237 ret = devm_gpiochip_add_data(dev, &pctl->gpio, pctl); 1238 if (ret) 1239 return ret; 1240 1241 ret = gpiochip_add_pin_range(&pctl->gpio, dev_name(dev), 1242 0, 0, pctl->data->npins); 1243 if (ret) 1244 return ret; 1245 1246 return 0; 1247 } 1248 1249 static struct i2c_driver sx150x_driver = { 1250 .driver = { 1251 .name = "sx150x-pinctrl", 1252 .of_match_table = of_match_ptr(sx150x_of_match), 1253 }, 1254 .probe = sx150x_probe, 1255 .id_table = sx150x_id, 1256 }; 1257 1258 static int __init sx150x_init(void) 1259 { 1260 return i2c_add_driver(&sx150x_driver); 1261 } 1262 subsys_initcall(sx150x_init); 1263