1 /* 2 * Generic GPIO driver for logic cells found in the Nomadik SoC 3 * 4 * Copyright (C) 2008,2009 STMicroelectronics 5 * Copyright (C) 2009 Alessandro Rubini <rubini@unipv.it> 6 * Rewritten based on work by Prafulla WADASKAR <prafulla.wadaskar@st.com> 7 * Copyright (C) 2011-2013 Linus Walleij <linus.walleij@linaro.org> 8 * 9 * This program is free software; you can redistribute it and/or modify 10 * it under the terms of the GNU General Public License version 2 as 11 * published by the Free Software Foundation. 12 */ 13 #include <linux/kernel.h> 14 #include <linux/module.h> 15 #include <linux/init.h> 16 #include <linux/device.h> 17 #include <linux/platform_device.h> 18 #include <linux/io.h> 19 #include <linux/clk.h> 20 #include <linux/err.h> 21 #include <linux/gpio.h> 22 #include <linux/spinlock.h> 23 #include <linux/interrupt.h> 24 #include <linux/slab.h> 25 #include <linux/of_device.h> 26 #include <linux/of_address.h> 27 #include <linux/bitops.h> 28 #include <linux/pinctrl/machine.h> 29 #include <linux/pinctrl/pinctrl.h> 30 #include <linux/pinctrl/pinmux.h> 31 #include <linux/pinctrl/pinconf.h> 32 /* Since we request GPIOs from ourself */ 33 #include <linux/pinctrl/consumer.h> 34 #include "pinctrl-nomadik.h" 35 #include "../core.h" 36 #include "../pinctrl-utils.h" 37 38 /* 39 * The GPIO module in the Nomadik family of Systems-on-Chip is an 40 * AMBA device, managing 32 pins and alternate functions. The logic block 41 * is currently used in the Nomadik and ux500. 42 * 43 * Symbols in this file are called "nmk_gpio" for "nomadik gpio" 44 */ 45 46 /* 47 * pin configurations are represented by 32-bit integers: 48 * 49 * bit 0.. 8 - Pin Number (512 Pins Maximum) 50 * bit 9..10 - Alternate Function Selection 51 * bit 11..12 - Pull up/down state 52 * bit 13 - Sleep mode behaviour 53 * bit 14 - Direction 54 * bit 15 - Value (if output) 55 * bit 16..18 - SLPM pull up/down state 56 * bit 19..20 - SLPM direction 57 * bit 21..22 - SLPM Value (if output) 58 * bit 23..25 - PDIS value (if input) 59 * bit 26 - Gpio mode 60 * bit 27 - Sleep mode 61 * 62 * to facilitate the definition, the following macros are provided 63 * 64 * PIN_CFG_DEFAULT - default config (0): 65 * pull up/down = disabled 66 * sleep mode = input/wakeup 67 * direction = input 68 * value = low 69 * SLPM direction = same as normal 70 * SLPM pull = same as normal 71 * SLPM value = same as normal 72 * 73 * PIN_CFG - default config with alternate function 74 */ 75 76 typedef unsigned long pin_cfg_t; 77 78 #define PIN_NUM_MASK 0x1ff 79 #define PIN_NUM(x) ((x) & PIN_NUM_MASK) 80 81 #define PIN_ALT_SHIFT 9 82 #define PIN_ALT_MASK (0x3 << PIN_ALT_SHIFT) 83 #define PIN_ALT(x) (((x) & PIN_ALT_MASK) >> PIN_ALT_SHIFT) 84 #define PIN_GPIO (NMK_GPIO_ALT_GPIO << PIN_ALT_SHIFT) 85 #define PIN_ALT_A (NMK_GPIO_ALT_A << PIN_ALT_SHIFT) 86 #define PIN_ALT_B (NMK_GPIO_ALT_B << PIN_ALT_SHIFT) 87 #define PIN_ALT_C (NMK_GPIO_ALT_C << PIN_ALT_SHIFT) 88 89 #define PIN_PULL_SHIFT 11 90 #define PIN_PULL_MASK (0x3 << PIN_PULL_SHIFT) 91 #define PIN_PULL(x) (((x) & PIN_PULL_MASK) >> PIN_PULL_SHIFT) 92 #define PIN_PULL_NONE (NMK_GPIO_PULL_NONE << PIN_PULL_SHIFT) 93 #define PIN_PULL_UP (NMK_GPIO_PULL_UP << PIN_PULL_SHIFT) 94 #define PIN_PULL_DOWN (NMK_GPIO_PULL_DOWN << PIN_PULL_SHIFT) 95 96 #define PIN_SLPM_SHIFT 13 97 #define PIN_SLPM_MASK (0x1 << PIN_SLPM_SHIFT) 98 #define PIN_SLPM(x) (((x) & PIN_SLPM_MASK) >> PIN_SLPM_SHIFT) 99 #define PIN_SLPM_MAKE_INPUT (NMK_GPIO_SLPM_INPUT << PIN_SLPM_SHIFT) 100 #define PIN_SLPM_NOCHANGE (NMK_GPIO_SLPM_NOCHANGE << PIN_SLPM_SHIFT) 101 /* These two replace the above in DB8500v2+ */ 102 #define PIN_SLPM_WAKEUP_ENABLE (NMK_GPIO_SLPM_WAKEUP_ENABLE << PIN_SLPM_SHIFT) 103 #define PIN_SLPM_WAKEUP_DISABLE (NMK_GPIO_SLPM_WAKEUP_DISABLE << PIN_SLPM_SHIFT) 104 #define PIN_SLPM_USE_MUX_SETTINGS_IN_SLEEP PIN_SLPM_WAKEUP_DISABLE 105 106 #define PIN_SLPM_GPIO PIN_SLPM_WAKEUP_ENABLE /* In SLPM, pin is a gpio */ 107 #define PIN_SLPM_ALTFUNC PIN_SLPM_WAKEUP_DISABLE /* In SLPM, pin is altfunc */ 108 109 #define PIN_DIR_SHIFT 14 110 #define PIN_DIR_MASK (0x1 << PIN_DIR_SHIFT) 111 #define PIN_DIR(x) (((x) & PIN_DIR_MASK) >> PIN_DIR_SHIFT) 112 #define PIN_DIR_INPUT (0 << PIN_DIR_SHIFT) 113 #define PIN_DIR_OUTPUT (1 << PIN_DIR_SHIFT) 114 115 #define PIN_VAL_SHIFT 15 116 #define PIN_VAL_MASK (0x1 << PIN_VAL_SHIFT) 117 #define PIN_VAL(x) (((x) & PIN_VAL_MASK) >> PIN_VAL_SHIFT) 118 #define PIN_VAL_LOW (0 << PIN_VAL_SHIFT) 119 #define PIN_VAL_HIGH (1 << PIN_VAL_SHIFT) 120 121 #define PIN_SLPM_PULL_SHIFT 16 122 #define PIN_SLPM_PULL_MASK (0x7 << PIN_SLPM_PULL_SHIFT) 123 #define PIN_SLPM_PULL(x) \ 124 (((x) & PIN_SLPM_PULL_MASK) >> PIN_SLPM_PULL_SHIFT) 125 #define PIN_SLPM_PULL_NONE \ 126 ((1 + NMK_GPIO_PULL_NONE) << PIN_SLPM_PULL_SHIFT) 127 #define PIN_SLPM_PULL_UP \ 128 ((1 + NMK_GPIO_PULL_UP) << PIN_SLPM_PULL_SHIFT) 129 #define PIN_SLPM_PULL_DOWN \ 130 ((1 + NMK_GPIO_PULL_DOWN) << PIN_SLPM_PULL_SHIFT) 131 132 #define PIN_SLPM_DIR_SHIFT 19 133 #define PIN_SLPM_DIR_MASK (0x3 << PIN_SLPM_DIR_SHIFT) 134 #define PIN_SLPM_DIR(x) \ 135 (((x) & PIN_SLPM_DIR_MASK) >> PIN_SLPM_DIR_SHIFT) 136 #define PIN_SLPM_DIR_INPUT ((1 + 0) << PIN_SLPM_DIR_SHIFT) 137 #define PIN_SLPM_DIR_OUTPUT ((1 + 1) << PIN_SLPM_DIR_SHIFT) 138 139 #define PIN_SLPM_VAL_SHIFT 21 140 #define PIN_SLPM_VAL_MASK (0x3 << PIN_SLPM_VAL_SHIFT) 141 #define PIN_SLPM_VAL(x) \ 142 (((x) & PIN_SLPM_VAL_MASK) >> PIN_SLPM_VAL_SHIFT) 143 #define PIN_SLPM_VAL_LOW ((1 + 0) << PIN_SLPM_VAL_SHIFT) 144 #define PIN_SLPM_VAL_HIGH ((1 + 1) << PIN_SLPM_VAL_SHIFT) 145 146 #define PIN_SLPM_PDIS_SHIFT 23 147 #define PIN_SLPM_PDIS_MASK (0x3 << PIN_SLPM_PDIS_SHIFT) 148 #define PIN_SLPM_PDIS(x) \ 149 (((x) & PIN_SLPM_PDIS_MASK) >> PIN_SLPM_PDIS_SHIFT) 150 #define PIN_SLPM_PDIS_NO_CHANGE (0 << PIN_SLPM_PDIS_SHIFT) 151 #define PIN_SLPM_PDIS_DISABLED (1 << PIN_SLPM_PDIS_SHIFT) 152 #define PIN_SLPM_PDIS_ENABLED (2 << PIN_SLPM_PDIS_SHIFT) 153 154 #define PIN_LOWEMI_SHIFT 25 155 #define PIN_LOWEMI_MASK (0x1 << PIN_LOWEMI_SHIFT) 156 #define PIN_LOWEMI(x) (((x) & PIN_LOWEMI_MASK) >> PIN_LOWEMI_SHIFT) 157 #define PIN_LOWEMI_DISABLED (0 << PIN_LOWEMI_SHIFT) 158 #define PIN_LOWEMI_ENABLED (1 << PIN_LOWEMI_SHIFT) 159 160 #define PIN_GPIOMODE_SHIFT 26 161 #define PIN_GPIOMODE_MASK (0x1 << PIN_GPIOMODE_SHIFT) 162 #define PIN_GPIOMODE(x) (((x) & PIN_GPIOMODE_MASK) >> PIN_GPIOMODE_SHIFT) 163 #define PIN_GPIOMODE_DISABLED (0 << PIN_GPIOMODE_SHIFT) 164 #define PIN_GPIOMODE_ENABLED (1 << PIN_GPIOMODE_SHIFT) 165 166 #define PIN_SLEEPMODE_SHIFT 27 167 #define PIN_SLEEPMODE_MASK (0x1 << PIN_SLEEPMODE_SHIFT) 168 #define PIN_SLEEPMODE(x) (((x) & PIN_SLEEPMODE_MASK) >> PIN_SLEEPMODE_SHIFT) 169 #define PIN_SLEEPMODE_DISABLED (0 << PIN_SLEEPMODE_SHIFT) 170 #define PIN_SLEEPMODE_ENABLED (1 << PIN_SLEEPMODE_SHIFT) 171 172 173 /* Shortcuts. Use these instead of separate DIR, PULL, and VAL. */ 174 #define PIN_INPUT_PULLDOWN (PIN_DIR_INPUT | PIN_PULL_DOWN) 175 #define PIN_INPUT_PULLUP (PIN_DIR_INPUT | PIN_PULL_UP) 176 #define PIN_INPUT_NOPULL (PIN_DIR_INPUT | PIN_PULL_NONE) 177 #define PIN_OUTPUT_LOW (PIN_DIR_OUTPUT | PIN_VAL_LOW) 178 #define PIN_OUTPUT_HIGH (PIN_DIR_OUTPUT | PIN_VAL_HIGH) 179 180 #define PIN_SLPM_INPUT_PULLDOWN (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_DOWN) 181 #define PIN_SLPM_INPUT_PULLUP (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_UP) 182 #define PIN_SLPM_INPUT_NOPULL (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_NONE) 183 #define PIN_SLPM_OUTPUT_LOW (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_LOW) 184 #define PIN_SLPM_OUTPUT_HIGH (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_HIGH) 185 186 #define PIN_CFG_DEFAULT (0) 187 188 #define PIN_CFG(num, alt) \ 189 (PIN_CFG_DEFAULT |\ 190 (PIN_NUM(num) | PIN_##alt)) 191 192 #define PIN_CFG_INPUT(num, alt, pull) \ 193 (PIN_CFG_DEFAULT |\ 194 (PIN_NUM(num) | PIN_##alt | PIN_INPUT_##pull)) 195 196 #define PIN_CFG_OUTPUT(num, alt, val) \ 197 (PIN_CFG_DEFAULT |\ 198 (PIN_NUM(num) | PIN_##alt | PIN_OUTPUT_##val)) 199 200 /* 201 * "nmk_gpio" and "NMK_GPIO" stand for "Nomadik GPIO", leaving 202 * the "gpio" namespace for generic and cross-machine functions 203 */ 204 205 #define GPIO_BLOCK_SHIFT 5 206 #define NMK_GPIO_PER_CHIP (1 << GPIO_BLOCK_SHIFT) 207 #define NMK_MAX_BANKS DIV_ROUND_UP(ARCH_NR_GPIOS, NMK_GPIO_PER_CHIP) 208 209 /* Register in the logic block */ 210 #define NMK_GPIO_DAT 0x00 211 #define NMK_GPIO_DATS 0x04 212 #define NMK_GPIO_DATC 0x08 213 #define NMK_GPIO_PDIS 0x0c 214 #define NMK_GPIO_DIR 0x10 215 #define NMK_GPIO_DIRS 0x14 216 #define NMK_GPIO_DIRC 0x18 217 #define NMK_GPIO_SLPC 0x1c 218 #define NMK_GPIO_AFSLA 0x20 219 #define NMK_GPIO_AFSLB 0x24 220 #define NMK_GPIO_LOWEMI 0x28 221 222 #define NMK_GPIO_RIMSC 0x40 223 #define NMK_GPIO_FIMSC 0x44 224 #define NMK_GPIO_IS 0x48 225 #define NMK_GPIO_IC 0x4c 226 #define NMK_GPIO_RWIMSC 0x50 227 #define NMK_GPIO_FWIMSC 0x54 228 #define NMK_GPIO_WKS 0x58 229 /* These appear in DB8540 and later ASICs */ 230 #define NMK_GPIO_EDGELEVEL 0x5C 231 #define NMK_GPIO_LEVEL 0x60 232 233 234 /* Pull up/down values */ 235 enum nmk_gpio_pull { 236 NMK_GPIO_PULL_NONE, 237 NMK_GPIO_PULL_UP, 238 NMK_GPIO_PULL_DOWN, 239 }; 240 241 /* Sleep mode */ 242 enum nmk_gpio_slpm { 243 NMK_GPIO_SLPM_INPUT, 244 NMK_GPIO_SLPM_WAKEUP_ENABLE = NMK_GPIO_SLPM_INPUT, 245 NMK_GPIO_SLPM_NOCHANGE, 246 NMK_GPIO_SLPM_WAKEUP_DISABLE = NMK_GPIO_SLPM_NOCHANGE, 247 }; 248 249 struct nmk_gpio_chip { 250 struct gpio_chip chip; 251 struct irq_chip irqchip; 252 void __iomem *addr; 253 struct clk *clk; 254 unsigned int bank; 255 unsigned int parent_irq; 256 int latent_parent_irq; 257 u32 (*get_latent_status)(unsigned int bank); 258 void (*set_ioforce)(bool enable); 259 spinlock_t lock; 260 bool sleepmode; 261 /* Keep track of configured edges */ 262 u32 edge_rising; 263 u32 edge_falling; 264 u32 real_wake; 265 u32 rwimsc; 266 u32 fwimsc; 267 u32 rimsc; 268 u32 fimsc; 269 u32 pull_up; 270 u32 lowemi; 271 }; 272 273 /** 274 * struct nmk_pinctrl - state container for the Nomadik pin controller 275 * @dev: containing device pointer 276 * @pctl: corresponding pin controller device 277 * @soc: SoC data for this specific chip 278 * @prcm_base: PRCM register range virtual base 279 */ 280 struct nmk_pinctrl { 281 struct device *dev; 282 struct pinctrl_dev *pctl; 283 const struct nmk_pinctrl_soc_data *soc; 284 void __iomem *prcm_base; 285 }; 286 287 static struct nmk_gpio_chip *nmk_gpio_chips[NMK_MAX_BANKS]; 288 289 static DEFINE_SPINLOCK(nmk_gpio_slpm_lock); 290 291 #define NUM_BANKS ARRAY_SIZE(nmk_gpio_chips) 292 293 static void __nmk_gpio_set_mode(struct nmk_gpio_chip *nmk_chip, 294 unsigned offset, int gpio_mode) 295 { 296 u32 afunc, bfunc; 297 298 afunc = readl(nmk_chip->addr + NMK_GPIO_AFSLA) & ~BIT(offset); 299 bfunc = readl(nmk_chip->addr + NMK_GPIO_AFSLB) & ~BIT(offset); 300 if (gpio_mode & NMK_GPIO_ALT_A) 301 afunc |= BIT(offset); 302 if (gpio_mode & NMK_GPIO_ALT_B) 303 bfunc |= BIT(offset); 304 writel(afunc, nmk_chip->addr + NMK_GPIO_AFSLA); 305 writel(bfunc, nmk_chip->addr + NMK_GPIO_AFSLB); 306 } 307 308 static void __nmk_gpio_set_slpm(struct nmk_gpio_chip *nmk_chip, 309 unsigned offset, enum nmk_gpio_slpm mode) 310 { 311 u32 slpm; 312 313 slpm = readl(nmk_chip->addr + NMK_GPIO_SLPC); 314 if (mode == NMK_GPIO_SLPM_NOCHANGE) 315 slpm |= BIT(offset); 316 else 317 slpm &= ~BIT(offset); 318 writel(slpm, nmk_chip->addr + NMK_GPIO_SLPC); 319 } 320 321 static void __nmk_gpio_set_pull(struct nmk_gpio_chip *nmk_chip, 322 unsigned offset, enum nmk_gpio_pull pull) 323 { 324 u32 pdis; 325 326 pdis = readl(nmk_chip->addr + NMK_GPIO_PDIS); 327 if (pull == NMK_GPIO_PULL_NONE) { 328 pdis |= BIT(offset); 329 nmk_chip->pull_up &= ~BIT(offset); 330 } else { 331 pdis &= ~BIT(offset); 332 } 333 334 writel(pdis, nmk_chip->addr + NMK_GPIO_PDIS); 335 336 if (pull == NMK_GPIO_PULL_UP) { 337 nmk_chip->pull_up |= BIT(offset); 338 writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DATS); 339 } else if (pull == NMK_GPIO_PULL_DOWN) { 340 nmk_chip->pull_up &= ~BIT(offset); 341 writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DATC); 342 } 343 } 344 345 static void __nmk_gpio_set_lowemi(struct nmk_gpio_chip *nmk_chip, 346 unsigned offset, bool lowemi) 347 { 348 bool enabled = nmk_chip->lowemi & BIT(offset); 349 350 if (lowemi == enabled) 351 return; 352 353 if (lowemi) 354 nmk_chip->lowemi |= BIT(offset); 355 else 356 nmk_chip->lowemi &= ~BIT(offset); 357 358 writel_relaxed(nmk_chip->lowemi, 359 nmk_chip->addr + NMK_GPIO_LOWEMI); 360 } 361 362 static void __nmk_gpio_make_input(struct nmk_gpio_chip *nmk_chip, 363 unsigned offset) 364 { 365 writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DIRC); 366 } 367 368 static void __nmk_gpio_set_output(struct nmk_gpio_chip *nmk_chip, 369 unsigned offset, int val) 370 { 371 if (val) 372 writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DATS); 373 else 374 writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DATC); 375 } 376 377 static void __nmk_gpio_make_output(struct nmk_gpio_chip *nmk_chip, 378 unsigned offset, int val) 379 { 380 writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DIRS); 381 __nmk_gpio_set_output(nmk_chip, offset, val); 382 } 383 384 static void __nmk_gpio_set_mode_safe(struct nmk_gpio_chip *nmk_chip, 385 unsigned offset, int gpio_mode, 386 bool glitch) 387 { 388 u32 rwimsc = nmk_chip->rwimsc; 389 u32 fwimsc = nmk_chip->fwimsc; 390 391 if (glitch && nmk_chip->set_ioforce) { 392 u32 bit = BIT(offset); 393 394 /* Prevent spurious wakeups */ 395 writel(rwimsc & ~bit, nmk_chip->addr + NMK_GPIO_RWIMSC); 396 writel(fwimsc & ~bit, nmk_chip->addr + NMK_GPIO_FWIMSC); 397 398 nmk_chip->set_ioforce(true); 399 } 400 401 __nmk_gpio_set_mode(nmk_chip, offset, gpio_mode); 402 403 if (glitch && nmk_chip->set_ioforce) { 404 nmk_chip->set_ioforce(false); 405 406 writel(rwimsc, nmk_chip->addr + NMK_GPIO_RWIMSC); 407 writel(fwimsc, nmk_chip->addr + NMK_GPIO_FWIMSC); 408 } 409 } 410 411 static void 412 nmk_gpio_disable_lazy_irq(struct nmk_gpio_chip *nmk_chip, unsigned offset) 413 { 414 u32 falling = nmk_chip->fimsc & BIT(offset); 415 u32 rising = nmk_chip->rimsc & BIT(offset); 416 int gpio = nmk_chip->chip.base + offset; 417 int irq = irq_find_mapping(nmk_chip->chip.irqdomain, offset); 418 struct irq_data *d = irq_get_irq_data(irq); 419 420 if (!rising && !falling) 421 return; 422 423 if (!d || !irqd_irq_disabled(d)) 424 return; 425 426 if (rising) { 427 nmk_chip->rimsc &= ~BIT(offset); 428 writel_relaxed(nmk_chip->rimsc, 429 nmk_chip->addr + NMK_GPIO_RIMSC); 430 } 431 432 if (falling) { 433 nmk_chip->fimsc &= ~BIT(offset); 434 writel_relaxed(nmk_chip->fimsc, 435 nmk_chip->addr + NMK_GPIO_FIMSC); 436 } 437 438 dev_dbg(nmk_chip->chip.parent, "%d: clearing interrupt mask\n", gpio); 439 } 440 441 static void nmk_write_masked(void __iomem *reg, u32 mask, u32 value) 442 { 443 u32 val; 444 445 val = readl(reg); 446 val = ((val & ~mask) | (value & mask)); 447 writel(val, reg); 448 } 449 450 static void nmk_prcm_altcx_set_mode(struct nmk_pinctrl *npct, 451 unsigned offset, unsigned alt_num) 452 { 453 int i; 454 u16 reg; 455 u8 bit; 456 u8 alt_index; 457 const struct prcm_gpiocr_altcx_pin_desc *pin_desc; 458 const u16 *gpiocr_regs; 459 460 if (!npct->prcm_base) 461 return; 462 463 if (alt_num > PRCM_IDX_GPIOCR_ALTC_MAX) { 464 dev_err(npct->dev, "PRCM GPIOCR: alternate-C%i is invalid\n", 465 alt_num); 466 return; 467 } 468 469 for (i = 0 ; i < npct->soc->npins_altcx ; i++) { 470 if (npct->soc->altcx_pins[i].pin == offset) 471 break; 472 } 473 if (i == npct->soc->npins_altcx) { 474 dev_dbg(npct->dev, "PRCM GPIOCR: pin %i is not found\n", 475 offset); 476 return; 477 } 478 479 pin_desc = npct->soc->altcx_pins + i; 480 gpiocr_regs = npct->soc->prcm_gpiocr_registers; 481 482 /* 483 * If alt_num is NULL, just clear current ALTCx selection 484 * to make sure we come back to a pure ALTC selection 485 */ 486 if (!alt_num) { 487 for (i = 0 ; i < PRCM_IDX_GPIOCR_ALTC_MAX ; i++) { 488 if (pin_desc->altcx[i].used == true) { 489 reg = gpiocr_regs[pin_desc->altcx[i].reg_index]; 490 bit = pin_desc->altcx[i].control_bit; 491 if (readl(npct->prcm_base + reg) & BIT(bit)) { 492 nmk_write_masked(npct->prcm_base + reg, BIT(bit), 0); 493 dev_dbg(npct->dev, 494 "PRCM GPIOCR: pin %i: alternate-C%i has been disabled\n", 495 offset, i+1); 496 } 497 } 498 } 499 return; 500 } 501 502 alt_index = alt_num - 1; 503 if (pin_desc->altcx[alt_index].used == false) { 504 dev_warn(npct->dev, 505 "PRCM GPIOCR: pin %i: alternate-C%i does not exist\n", 506 offset, alt_num); 507 return; 508 } 509 510 /* 511 * Check if any other ALTCx functions are activated on this pin 512 * and disable it first. 513 */ 514 for (i = 0 ; i < PRCM_IDX_GPIOCR_ALTC_MAX ; i++) { 515 if (i == alt_index) 516 continue; 517 if (pin_desc->altcx[i].used == true) { 518 reg = gpiocr_regs[pin_desc->altcx[i].reg_index]; 519 bit = pin_desc->altcx[i].control_bit; 520 if (readl(npct->prcm_base + reg) & BIT(bit)) { 521 nmk_write_masked(npct->prcm_base + reg, BIT(bit), 0); 522 dev_dbg(npct->dev, 523 "PRCM GPIOCR: pin %i: alternate-C%i has been disabled\n", 524 offset, i+1); 525 } 526 } 527 } 528 529 reg = gpiocr_regs[pin_desc->altcx[alt_index].reg_index]; 530 bit = pin_desc->altcx[alt_index].control_bit; 531 dev_dbg(npct->dev, "PRCM GPIOCR: pin %i: alternate-C%i has been selected\n", 532 offset, alt_index+1); 533 nmk_write_masked(npct->prcm_base + reg, BIT(bit), BIT(bit)); 534 } 535 536 /* 537 * Safe sequence used to switch IOs between GPIO and Alternate-C mode: 538 * - Save SLPM registers 539 * - Set SLPM=0 for the IOs you want to switch and others to 1 540 * - Configure the GPIO registers for the IOs that are being switched 541 * - Set IOFORCE=1 542 * - Modify the AFLSA/B registers for the IOs that are being switched 543 * - Set IOFORCE=0 544 * - Restore SLPM registers 545 * - Any spurious wake up event during switch sequence to be ignored and 546 * cleared 547 */ 548 static void nmk_gpio_glitch_slpm_init(unsigned int *slpm) 549 { 550 int i; 551 552 for (i = 0; i < NUM_BANKS; i++) { 553 struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; 554 unsigned int temp = slpm[i]; 555 556 if (!chip) 557 break; 558 559 clk_enable(chip->clk); 560 561 slpm[i] = readl(chip->addr + NMK_GPIO_SLPC); 562 writel(temp, chip->addr + NMK_GPIO_SLPC); 563 } 564 } 565 566 static void nmk_gpio_glitch_slpm_restore(unsigned int *slpm) 567 { 568 int i; 569 570 for (i = 0; i < NUM_BANKS; i++) { 571 struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; 572 573 if (!chip) 574 break; 575 576 writel(slpm[i], chip->addr + NMK_GPIO_SLPC); 577 578 clk_disable(chip->clk); 579 } 580 } 581 582 static int __maybe_unused nmk_prcm_gpiocr_get_mode(struct pinctrl_dev *pctldev, int gpio) 583 { 584 int i; 585 u16 reg; 586 u8 bit; 587 struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); 588 const struct prcm_gpiocr_altcx_pin_desc *pin_desc; 589 const u16 *gpiocr_regs; 590 591 if (!npct->prcm_base) 592 return NMK_GPIO_ALT_C; 593 594 for (i = 0; i < npct->soc->npins_altcx; i++) { 595 if (npct->soc->altcx_pins[i].pin == gpio) 596 break; 597 } 598 if (i == npct->soc->npins_altcx) 599 return NMK_GPIO_ALT_C; 600 601 pin_desc = npct->soc->altcx_pins + i; 602 gpiocr_regs = npct->soc->prcm_gpiocr_registers; 603 for (i = 0; i < PRCM_IDX_GPIOCR_ALTC_MAX; i++) { 604 if (pin_desc->altcx[i].used == true) { 605 reg = gpiocr_regs[pin_desc->altcx[i].reg_index]; 606 bit = pin_desc->altcx[i].control_bit; 607 if (readl(npct->prcm_base + reg) & BIT(bit)) 608 return NMK_GPIO_ALT_C+i+1; 609 } 610 } 611 return NMK_GPIO_ALT_C; 612 } 613 614 /* IRQ functions */ 615 616 static void nmk_gpio_irq_ack(struct irq_data *d) 617 { 618 struct gpio_chip *chip = irq_data_get_irq_chip_data(d); 619 struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); 620 621 clk_enable(nmk_chip->clk); 622 writel(BIT(d->hwirq), nmk_chip->addr + NMK_GPIO_IC); 623 clk_disable(nmk_chip->clk); 624 } 625 626 enum nmk_gpio_irq_type { 627 NORMAL, 628 WAKE, 629 }; 630 631 static void __nmk_gpio_irq_modify(struct nmk_gpio_chip *nmk_chip, 632 int offset, enum nmk_gpio_irq_type which, 633 bool enable) 634 { 635 u32 *rimscval; 636 u32 *fimscval; 637 u32 rimscreg; 638 u32 fimscreg; 639 640 if (which == NORMAL) { 641 rimscreg = NMK_GPIO_RIMSC; 642 fimscreg = NMK_GPIO_FIMSC; 643 rimscval = &nmk_chip->rimsc; 644 fimscval = &nmk_chip->fimsc; 645 } else { 646 rimscreg = NMK_GPIO_RWIMSC; 647 fimscreg = NMK_GPIO_FWIMSC; 648 rimscval = &nmk_chip->rwimsc; 649 fimscval = &nmk_chip->fwimsc; 650 } 651 652 /* we must individually set/clear the two edges */ 653 if (nmk_chip->edge_rising & BIT(offset)) { 654 if (enable) 655 *rimscval |= BIT(offset); 656 else 657 *rimscval &= ~BIT(offset); 658 writel(*rimscval, nmk_chip->addr + rimscreg); 659 } 660 if (nmk_chip->edge_falling & BIT(offset)) { 661 if (enable) 662 *fimscval |= BIT(offset); 663 else 664 *fimscval &= ~BIT(offset); 665 writel(*fimscval, nmk_chip->addr + fimscreg); 666 } 667 } 668 669 static void __nmk_gpio_set_wake(struct nmk_gpio_chip *nmk_chip, 670 int offset, bool on) 671 { 672 /* 673 * Ensure WAKEUP_ENABLE is on. No need to disable it if wakeup is 674 * disabled, since setting SLPM to 1 increases power consumption, and 675 * wakeup is anyhow controlled by the RIMSC and FIMSC registers. 676 */ 677 if (nmk_chip->sleepmode && on) { 678 __nmk_gpio_set_slpm(nmk_chip, offset, 679 NMK_GPIO_SLPM_WAKEUP_ENABLE); 680 } 681 682 __nmk_gpio_irq_modify(nmk_chip, offset, WAKE, on); 683 } 684 685 static int nmk_gpio_irq_maskunmask(struct irq_data *d, bool enable) 686 { 687 struct nmk_gpio_chip *nmk_chip; 688 unsigned long flags; 689 690 nmk_chip = irq_data_get_irq_chip_data(d); 691 if (!nmk_chip) 692 return -EINVAL; 693 694 clk_enable(nmk_chip->clk); 695 spin_lock_irqsave(&nmk_gpio_slpm_lock, flags); 696 spin_lock(&nmk_chip->lock); 697 698 __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, enable); 699 700 if (!(nmk_chip->real_wake & BIT(d->hwirq))) 701 __nmk_gpio_set_wake(nmk_chip, d->hwirq, enable); 702 703 spin_unlock(&nmk_chip->lock); 704 spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags); 705 clk_disable(nmk_chip->clk); 706 707 return 0; 708 } 709 710 static void nmk_gpio_irq_mask(struct irq_data *d) 711 { 712 nmk_gpio_irq_maskunmask(d, false); 713 } 714 715 static void nmk_gpio_irq_unmask(struct irq_data *d) 716 { 717 nmk_gpio_irq_maskunmask(d, true); 718 } 719 720 static int nmk_gpio_irq_set_wake(struct irq_data *d, unsigned int on) 721 { 722 struct nmk_gpio_chip *nmk_chip; 723 unsigned long flags; 724 725 nmk_chip = irq_data_get_irq_chip_data(d); 726 if (!nmk_chip) 727 return -EINVAL; 728 729 clk_enable(nmk_chip->clk); 730 spin_lock_irqsave(&nmk_gpio_slpm_lock, flags); 731 spin_lock(&nmk_chip->lock); 732 733 if (irqd_irq_disabled(d)) 734 __nmk_gpio_set_wake(nmk_chip, d->hwirq, on); 735 736 if (on) 737 nmk_chip->real_wake |= BIT(d->hwirq); 738 else 739 nmk_chip->real_wake &= ~BIT(d->hwirq); 740 741 spin_unlock(&nmk_chip->lock); 742 spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags); 743 clk_disable(nmk_chip->clk); 744 745 return 0; 746 } 747 748 static int nmk_gpio_irq_set_type(struct irq_data *d, unsigned int type) 749 { 750 bool enabled = !irqd_irq_disabled(d); 751 bool wake = irqd_is_wakeup_set(d); 752 struct nmk_gpio_chip *nmk_chip; 753 unsigned long flags; 754 755 nmk_chip = irq_data_get_irq_chip_data(d); 756 if (!nmk_chip) 757 return -EINVAL; 758 if (type & IRQ_TYPE_LEVEL_HIGH) 759 return -EINVAL; 760 if (type & IRQ_TYPE_LEVEL_LOW) 761 return -EINVAL; 762 763 clk_enable(nmk_chip->clk); 764 spin_lock_irqsave(&nmk_chip->lock, flags); 765 766 if (enabled) 767 __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, false); 768 769 if (enabled || wake) 770 __nmk_gpio_irq_modify(nmk_chip, d->hwirq, WAKE, false); 771 772 nmk_chip->edge_rising &= ~BIT(d->hwirq); 773 if (type & IRQ_TYPE_EDGE_RISING) 774 nmk_chip->edge_rising |= BIT(d->hwirq); 775 776 nmk_chip->edge_falling &= ~BIT(d->hwirq); 777 if (type & IRQ_TYPE_EDGE_FALLING) 778 nmk_chip->edge_falling |= BIT(d->hwirq); 779 780 if (enabled) 781 __nmk_gpio_irq_modify(nmk_chip, d->hwirq, NORMAL, true); 782 783 if (enabled || wake) 784 __nmk_gpio_irq_modify(nmk_chip, d->hwirq, WAKE, true); 785 786 spin_unlock_irqrestore(&nmk_chip->lock, flags); 787 clk_disable(nmk_chip->clk); 788 789 return 0; 790 } 791 792 static unsigned int nmk_gpio_irq_startup(struct irq_data *d) 793 { 794 struct nmk_gpio_chip *nmk_chip = irq_data_get_irq_chip_data(d); 795 796 clk_enable(nmk_chip->clk); 797 nmk_gpio_irq_unmask(d); 798 return 0; 799 } 800 801 static void nmk_gpio_irq_shutdown(struct irq_data *d) 802 { 803 struct nmk_gpio_chip *nmk_chip = irq_data_get_irq_chip_data(d); 804 805 nmk_gpio_irq_mask(d); 806 clk_disable(nmk_chip->clk); 807 } 808 809 static void __nmk_gpio_irq_handler(struct irq_desc *desc, u32 status) 810 { 811 struct irq_chip *host_chip = irq_desc_get_chip(desc); 812 struct gpio_chip *chip = irq_desc_get_handler_data(desc); 813 814 chained_irq_enter(host_chip, desc); 815 816 while (status) { 817 int bit = __ffs(status); 818 819 generic_handle_irq(irq_find_mapping(chip->irqdomain, bit)); 820 status &= ~BIT(bit); 821 } 822 823 chained_irq_exit(host_chip, desc); 824 } 825 826 static void nmk_gpio_irq_handler(struct irq_desc *desc) 827 { 828 struct gpio_chip *chip = irq_desc_get_handler_data(desc); 829 struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); 830 u32 status; 831 832 clk_enable(nmk_chip->clk); 833 status = readl(nmk_chip->addr + NMK_GPIO_IS); 834 clk_disable(nmk_chip->clk); 835 836 __nmk_gpio_irq_handler(desc, status); 837 } 838 839 static void nmk_gpio_latent_irq_handler(struct irq_desc *desc) 840 { 841 struct gpio_chip *chip = irq_desc_get_handler_data(desc); 842 struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); 843 u32 status = nmk_chip->get_latent_status(nmk_chip->bank); 844 845 __nmk_gpio_irq_handler(desc, status); 846 } 847 848 /* I/O Functions */ 849 850 static int nmk_gpio_get_dir(struct gpio_chip *chip, unsigned offset) 851 { 852 struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); 853 int dir; 854 855 clk_enable(nmk_chip->clk); 856 857 dir = !!(readl(nmk_chip->addr + NMK_GPIO_DIR) & BIT(offset)); 858 859 clk_disable(nmk_chip->clk); 860 861 return dir; 862 } 863 864 static int nmk_gpio_make_input(struct gpio_chip *chip, unsigned offset) 865 { 866 struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); 867 868 clk_enable(nmk_chip->clk); 869 870 writel(BIT(offset), nmk_chip->addr + NMK_GPIO_DIRC); 871 872 clk_disable(nmk_chip->clk); 873 874 return 0; 875 } 876 877 static int nmk_gpio_get_input(struct gpio_chip *chip, unsigned offset) 878 { 879 struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); 880 int value; 881 882 clk_enable(nmk_chip->clk); 883 884 value = !!(readl(nmk_chip->addr + NMK_GPIO_DAT) & BIT(offset)); 885 886 clk_disable(nmk_chip->clk); 887 888 return value; 889 } 890 891 static void nmk_gpio_set_output(struct gpio_chip *chip, unsigned offset, 892 int val) 893 { 894 struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); 895 896 clk_enable(nmk_chip->clk); 897 898 __nmk_gpio_set_output(nmk_chip, offset, val); 899 900 clk_disable(nmk_chip->clk); 901 } 902 903 static int nmk_gpio_make_output(struct gpio_chip *chip, unsigned offset, 904 int val) 905 { 906 struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); 907 908 clk_enable(nmk_chip->clk); 909 910 __nmk_gpio_make_output(nmk_chip, offset, val); 911 912 clk_disable(nmk_chip->clk); 913 914 return 0; 915 } 916 917 #ifdef CONFIG_DEBUG_FS 918 static int nmk_gpio_get_mode(struct nmk_gpio_chip *nmk_chip, int offset) 919 { 920 u32 afunc, bfunc; 921 922 clk_enable(nmk_chip->clk); 923 924 afunc = readl(nmk_chip->addr + NMK_GPIO_AFSLA) & BIT(offset); 925 bfunc = readl(nmk_chip->addr + NMK_GPIO_AFSLB) & BIT(offset); 926 927 clk_disable(nmk_chip->clk); 928 929 return (afunc ? NMK_GPIO_ALT_A : 0) | (bfunc ? NMK_GPIO_ALT_B : 0); 930 } 931 932 #include <linux/seq_file.h> 933 934 static void nmk_gpio_dbg_show_one(struct seq_file *s, 935 struct pinctrl_dev *pctldev, struct gpio_chip *chip, 936 unsigned offset, unsigned gpio) 937 { 938 const char *label = gpiochip_is_requested(chip, offset); 939 struct nmk_gpio_chip *nmk_chip = gpiochip_get_data(chip); 940 int mode; 941 bool is_out; 942 bool data_out; 943 bool pull; 944 const char *modes[] = { 945 [NMK_GPIO_ALT_GPIO] = "gpio", 946 [NMK_GPIO_ALT_A] = "altA", 947 [NMK_GPIO_ALT_B] = "altB", 948 [NMK_GPIO_ALT_C] = "altC", 949 [NMK_GPIO_ALT_C+1] = "altC1", 950 [NMK_GPIO_ALT_C+2] = "altC2", 951 [NMK_GPIO_ALT_C+3] = "altC3", 952 [NMK_GPIO_ALT_C+4] = "altC4", 953 }; 954 const char *pulls[] = { 955 "none ", 956 "pull down", 957 "pull up ", 958 }; 959 960 clk_enable(nmk_chip->clk); 961 is_out = !!(readl(nmk_chip->addr + NMK_GPIO_DIR) & BIT(offset)); 962 pull = !(readl(nmk_chip->addr + NMK_GPIO_PDIS) & BIT(offset)); 963 data_out = !!(readl(nmk_chip->addr + NMK_GPIO_DAT) & BIT(offset)); 964 mode = nmk_gpio_get_mode(nmk_chip, offset); 965 if ((mode == NMK_GPIO_ALT_C) && pctldev) 966 mode = nmk_prcm_gpiocr_get_mode(pctldev, gpio); 967 968 if (is_out) { 969 seq_printf(s, " gpio-%-3d (%-20.20s) out %s %s", 970 gpio, 971 label ?: "(none)", 972 data_out ? "hi" : "lo", 973 (mode < 0) ? "unknown" : modes[mode]); 974 } else { 975 int irq = gpio_to_irq(gpio); 976 struct irq_desc *desc = irq_to_desc(irq); 977 int pullidx = 0; 978 int val; 979 980 if (pull) 981 pullidx = data_out ? 1 : 2; 982 983 seq_printf(s, " gpio-%-3d (%-20.20s) in %s %s", 984 gpio, 985 label ?: "(none)", 986 pulls[pullidx], 987 (mode < 0) ? "unknown" : modes[mode]); 988 989 val = nmk_gpio_get_input(chip, offset); 990 seq_printf(s, " VAL %d", val); 991 992 /* 993 * This races with request_irq(), set_irq_type(), 994 * and set_irq_wake() ... but those are "rare". 995 */ 996 if (irq > 0 && desc && desc->action) { 997 char *trigger; 998 999 if (nmk_chip->edge_rising & BIT(offset)) 1000 trigger = "edge-rising"; 1001 else if (nmk_chip->edge_falling & BIT(offset)) 1002 trigger = "edge-falling"; 1003 else 1004 trigger = "edge-undefined"; 1005 1006 seq_printf(s, " irq-%d %s%s", 1007 irq, trigger, 1008 irqd_is_wakeup_set(&desc->irq_data) 1009 ? " wakeup" : ""); 1010 } 1011 } 1012 clk_disable(nmk_chip->clk); 1013 } 1014 1015 static void nmk_gpio_dbg_show(struct seq_file *s, struct gpio_chip *chip) 1016 { 1017 unsigned i; 1018 unsigned gpio = chip->base; 1019 1020 for (i = 0; i < chip->ngpio; i++, gpio++) { 1021 nmk_gpio_dbg_show_one(s, NULL, chip, i, gpio); 1022 seq_printf(s, "\n"); 1023 } 1024 } 1025 1026 #else 1027 static inline void nmk_gpio_dbg_show_one(struct seq_file *s, 1028 struct pinctrl_dev *pctldev, 1029 struct gpio_chip *chip, 1030 unsigned offset, unsigned gpio) 1031 { 1032 } 1033 #define nmk_gpio_dbg_show NULL 1034 #endif 1035 1036 void nmk_gpio_clocks_enable(void) 1037 { 1038 int i; 1039 1040 for (i = 0; i < NUM_BANKS; i++) { 1041 struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; 1042 1043 if (!chip) 1044 continue; 1045 1046 clk_enable(chip->clk); 1047 } 1048 } 1049 1050 void nmk_gpio_clocks_disable(void) 1051 { 1052 int i; 1053 1054 for (i = 0; i < NUM_BANKS; i++) { 1055 struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; 1056 1057 if (!chip) 1058 continue; 1059 1060 clk_disable(chip->clk); 1061 } 1062 } 1063 1064 /* 1065 * Called from the suspend/resume path to only keep the real wakeup interrupts 1066 * (those that have had set_irq_wake() called on them) as wakeup interrupts, 1067 * and not the rest of the interrupts which we needed to have as wakeups for 1068 * cpuidle. 1069 * 1070 * PM ops are not used since this needs to be done at the end, after all the 1071 * other drivers are done with their suspend callbacks. 1072 */ 1073 void nmk_gpio_wakeups_suspend(void) 1074 { 1075 int i; 1076 1077 for (i = 0; i < NUM_BANKS; i++) { 1078 struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; 1079 1080 if (!chip) 1081 break; 1082 1083 clk_enable(chip->clk); 1084 1085 writel(chip->rwimsc & chip->real_wake, 1086 chip->addr + NMK_GPIO_RWIMSC); 1087 writel(chip->fwimsc & chip->real_wake, 1088 chip->addr + NMK_GPIO_FWIMSC); 1089 1090 clk_disable(chip->clk); 1091 } 1092 } 1093 1094 void nmk_gpio_wakeups_resume(void) 1095 { 1096 int i; 1097 1098 for (i = 0; i < NUM_BANKS; i++) { 1099 struct nmk_gpio_chip *chip = nmk_gpio_chips[i]; 1100 1101 if (!chip) 1102 break; 1103 1104 clk_enable(chip->clk); 1105 1106 writel(chip->rwimsc, chip->addr + NMK_GPIO_RWIMSC); 1107 writel(chip->fwimsc, chip->addr + NMK_GPIO_FWIMSC); 1108 1109 clk_disable(chip->clk); 1110 } 1111 } 1112 1113 /* 1114 * Read the pull up/pull down status. 1115 * A bit set in 'pull_up' means that pull up 1116 * is selected if pull is enabled in PDIS register. 1117 * Note: only pull up/down set via this driver can 1118 * be detected due to HW limitations. 1119 */ 1120 void nmk_gpio_read_pull(int gpio_bank, u32 *pull_up) 1121 { 1122 if (gpio_bank < NUM_BANKS) { 1123 struct nmk_gpio_chip *chip = nmk_gpio_chips[gpio_bank]; 1124 1125 if (!chip) 1126 return; 1127 1128 *pull_up = chip->pull_up; 1129 } 1130 } 1131 1132 /* 1133 * We will allocate memory for the state container using devm* allocators 1134 * binding to the first device reaching this point, it doesn't matter if 1135 * it is the pin controller or GPIO driver. However we need to use the right 1136 * platform device when looking up resources so pay attention to pdev. 1137 */ 1138 static struct nmk_gpio_chip *nmk_gpio_populate_chip(struct device_node *np, 1139 struct platform_device *pdev) 1140 { 1141 struct nmk_gpio_chip *nmk_chip; 1142 struct platform_device *gpio_pdev; 1143 struct gpio_chip *chip; 1144 struct resource *res; 1145 struct clk *clk; 1146 void __iomem *base; 1147 u32 id; 1148 1149 gpio_pdev = of_find_device_by_node(np); 1150 if (!gpio_pdev) { 1151 pr_err("populate \"%s\": device not found\n", np->name); 1152 return ERR_PTR(-ENODEV); 1153 } 1154 if (of_property_read_u32(np, "gpio-bank", &id)) { 1155 dev_err(&pdev->dev, "populate: gpio-bank property not found\n"); 1156 return ERR_PTR(-EINVAL); 1157 } 1158 1159 /* Already populated? */ 1160 nmk_chip = nmk_gpio_chips[id]; 1161 if (nmk_chip) 1162 return nmk_chip; 1163 1164 nmk_chip = devm_kzalloc(&pdev->dev, sizeof(*nmk_chip), GFP_KERNEL); 1165 if (!nmk_chip) 1166 return ERR_PTR(-ENOMEM); 1167 1168 nmk_chip->bank = id; 1169 chip = &nmk_chip->chip; 1170 chip->base = id * NMK_GPIO_PER_CHIP; 1171 chip->ngpio = NMK_GPIO_PER_CHIP; 1172 chip->label = dev_name(&gpio_pdev->dev); 1173 chip->parent = &gpio_pdev->dev; 1174 1175 res = platform_get_resource(gpio_pdev, IORESOURCE_MEM, 0); 1176 base = devm_ioremap_resource(&pdev->dev, res); 1177 if (IS_ERR(base)) 1178 return base; 1179 nmk_chip->addr = base; 1180 1181 clk = clk_get(&gpio_pdev->dev, NULL); 1182 if (IS_ERR(clk)) 1183 return (void *) clk; 1184 clk_prepare(clk); 1185 nmk_chip->clk = clk; 1186 1187 BUG_ON(nmk_chip->bank >= ARRAY_SIZE(nmk_gpio_chips)); 1188 nmk_gpio_chips[id] = nmk_chip; 1189 return nmk_chip; 1190 } 1191 1192 static int nmk_gpio_probe(struct platform_device *dev) 1193 { 1194 struct device_node *np = dev->dev.of_node; 1195 struct nmk_gpio_chip *nmk_chip; 1196 struct gpio_chip *chip; 1197 struct irq_chip *irqchip; 1198 int latent_irq; 1199 bool supports_sleepmode; 1200 int irq; 1201 int ret; 1202 1203 nmk_chip = nmk_gpio_populate_chip(np, dev); 1204 if (IS_ERR(nmk_chip)) { 1205 dev_err(&dev->dev, "could not populate nmk chip struct\n"); 1206 return PTR_ERR(nmk_chip); 1207 } 1208 1209 if (of_get_property(np, "st,supports-sleepmode", NULL)) 1210 supports_sleepmode = true; 1211 else 1212 supports_sleepmode = false; 1213 1214 /* Correct platform device ID */ 1215 dev->id = nmk_chip->bank; 1216 1217 irq = platform_get_irq(dev, 0); 1218 if (irq < 0) 1219 return irq; 1220 1221 /* It's OK for this IRQ not to be present */ 1222 latent_irq = platform_get_irq(dev, 1); 1223 1224 /* 1225 * The virt address in nmk_chip->addr is in the nomadik register space, 1226 * so we can simply convert the resource address, without remapping 1227 */ 1228 nmk_chip->parent_irq = irq; 1229 nmk_chip->latent_parent_irq = latent_irq; 1230 nmk_chip->sleepmode = supports_sleepmode; 1231 spin_lock_init(&nmk_chip->lock); 1232 1233 chip = &nmk_chip->chip; 1234 chip->request = gpiochip_generic_request; 1235 chip->free = gpiochip_generic_free; 1236 chip->get_direction = nmk_gpio_get_dir; 1237 chip->direction_input = nmk_gpio_make_input; 1238 chip->get = nmk_gpio_get_input; 1239 chip->direction_output = nmk_gpio_make_output; 1240 chip->set = nmk_gpio_set_output; 1241 chip->dbg_show = nmk_gpio_dbg_show; 1242 chip->can_sleep = false; 1243 chip->owner = THIS_MODULE; 1244 1245 irqchip = &nmk_chip->irqchip; 1246 irqchip->irq_ack = nmk_gpio_irq_ack; 1247 irqchip->irq_mask = nmk_gpio_irq_mask; 1248 irqchip->irq_unmask = nmk_gpio_irq_unmask; 1249 irqchip->irq_set_type = nmk_gpio_irq_set_type; 1250 irqchip->irq_set_wake = nmk_gpio_irq_set_wake; 1251 irqchip->irq_startup = nmk_gpio_irq_startup; 1252 irqchip->irq_shutdown = nmk_gpio_irq_shutdown; 1253 irqchip->flags = IRQCHIP_MASK_ON_SUSPEND; 1254 irqchip->name = kasprintf(GFP_KERNEL, "nmk%u-%u-%u", 1255 dev->id, 1256 chip->base, 1257 chip->base + chip->ngpio - 1); 1258 1259 clk_enable(nmk_chip->clk); 1260 nmk_chip->lowemi = readl_relaxed(nmk_chip->addr + NMK_GPIO_LOWEMI); 1261 clk_disable(nmk_chip->clk); 1262 chip->of_node = np; 1263 1264 ret = gpiochip_add_data(chip, nmk_chip); 1265 if (ret) 1266 return ret; 1267 1268 platform_set_drvdata(dev, nmk_chip); 1269 1270 /* 1271 * Let the generic code handle this edge IRQ, the the chained 1272 * handler will perform the actual work of handling the parent 1273 * interrupt. 1274 */ 1275 ret = gpiochip_irqchip_add(chip, 1276 irqchip, 1277 0, 1278 handle_edge_irq, 1279 IRQ_TYPE_EDGE_FALLING); 1280 if (ret) { 1281 dev_err(&dev->dev, "could not add irqchip\n"); 1282 gpiochip_remove(&nmk_chip->chip); 1283 return -ENODEV; 1284 } 1285 /* Then register the chain on the parent IRQ */ 1286 gpiochip_set_chained_irqchip(chip, 1287 irqchip, 1288 nmk_chip->parent_irq, 1289 nmk_gpio_irq_handler); 1290 if (nmk_chip->latent_parent_irq > 0) 1291 gpiochip_set_chained_irqchip(chip, 1292 irqchip, 1293 nmk_chip->latent_parent_irq, 1294 nmk_gpio_latent_irq_handler); 1295 1296 dev_info(&dev->dev, "at address %p\n", nmk_chip->addr); 1297 1298 return 0; 1299 } 1300 1301 static int nmk_get_groups_cnt(struct pinctrl_dev *pctldev) 1302 { 1303 struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); 1304 1305 return npct->soc->ngroups; 1306 } 1307 1308 static const char *nmk_get_group_name(struct pinctrl_dev *pctldev, 1309 unsigned selector) 1310 { 1311 struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); 1312 1313 return npct->soc->groups[selector].name; 1314 } 1315 1316 static int nmk_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector, 1317 const unsigned **pins, 1318 unsigned *num_pins) 1319 { 1320 struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); 1321 1322 *pins = npct->soc->groups[selector].pins; 1323 *num_pins = npct->soc->groups[selector].npins; 1324 return 0; 1325 } 1326 1327 static struct nmk_gpio_chip *find_nmk_gpio_from_pin(unsigned pin) 1328 { 1329 int i; 1330 struct nmk_gpio_chip *nmk_gpio; 1331 1332 for(i = 0; i < NMK_MAX_BANKS; i++) { 1333 nmk_gpio = nmk_gpio_chips[i]; 1334 if (!nmk_gpio) 1335 continue; 1336 if (pin >= nmk_gpio->chip.base && 1337 pin < nmk_gpio->chip.base + nmk_gpio->chip.ngpio) 1338 return nmk_gpio; 1339 } 1340 return NULL; 1341 } 1342 1343 static struct gpio_chip *find_gc_from_pin(unsigned pin) 1344 { 1345 struct nmk_gpio_chip *nmk_gpio = find_nmk_gpio_from_pin(pin); 1346 1347 if (nmk_gpio) 1348 return &nmk_gpio->chip; 1349 return NULL; 1350 } 1351 1352 static void nmk_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s, 1353 unsigned offset) 1354 { 1355 struct gpio_chip *chip = find_gc_from_pin(offset); 1356 1357 if (!chip) { 1358 seq_printf(s, "invalid pin offset"); 1359 return; 1360 } 1361 nmk_gpio_dbg_show_one(s, pctldev, chip, offset - chip->base, offset); 1362 } 1363 1364 static int nmk_dt_add_map_mux(struct pinctrl_map **map, unsigned *reserved_maps, 1365 unsigned *num_maps, const char *group, 1366 const char *function) 1367 { 1368 if (*num_maps == *reserved_maps) 1369 return -ENOSPC; 1370 1371 (*map)[*num_maps].type = PIN_MAP_TYPE_MUX_GROUP; 1372 (*map)[*num_maps].data.mux.group = group; 1373 (*map)[*num_maps].data.mux.function = function; 1374 (*num_maps)++; 1375 1376 return 0; 1377 } 1378 1379 static int nmk_dt_add_map_configs(struct pinctrl_map **map, 1380 unsigned *reserved_maps, 1381 unsigned *num_maps, const char *group, 1382 unsigned long *configs, unsigned num_configs) 1383 { 1384 unsigned long *dup_configs; 1385 1386 if (*num_maps == *reserved_maps) 1387 return -ENOSPC; 1388 1389 dup_configs = kmemdup(configs, num_configs * sizeof(*dup_configs), 1390 GFP_KERNEL); 1391 if (!dup_configs) 1392 return -ENOMEM; 1393 1394 (*map)[*num_maps].type = PIN_MAP_TYPE_CONFIGS_PIN; 1395 1396 (*map)[*num_maps].data.configs.group_or_pin = group; 1397 (*map)[*num_maps].data.configs.configs = dup_configs; 1398 (*map)[*num_maps].data.configs.num_configs = num_configs; 1399 (*num_maps)++; 1400 1401 return 0; 1402 } 1403 1404 #define NMK_CONFIG_PIN(x, y) { .property = x, .config = y, } 1405 #define NMK_CONFIG_PIN_ARRAY(x, y) { .property = x, .choice = y, \ 1406 .size = ARRAY_SIZE(y), } 1407 1408 static const unsigned long nmk_pin_input_modes[] = { 1409 PIN_INPUT_NOPULL, 1410 PIN_INPUT_PULLUP, 1411 PIN_INPUT_PULLDOWN, 1412 }; 1413 1414 static const unsigned long nmk_pin_output_modes[] = { 1415 PIN_OUTPUT_LOW, 1416 PIN_OUTPUT_HIGH, 1417 PIN_DIR_OUTPUT, 1418 }; 1419 1420 static const unsigned long nmk_pin_sleep_modes[] = { 1421 PIN_SLEEPMODE_DISABLED, 1422 PIN_SLEEPMODE_ENABLED, 1423 }; 1424 1425 static const unsigned long nmk_pin_sleep_input_modes[] = { 1426 PIN_SLPM_INPUT_NOPULL, 1427 PIN_SLPM_INPUT_PULLUP, 1428 PIN_SLPM_INPUT_PULLDOWN, 1429 PIN_SLPM_DIR_INPUT, 1430 }; 1431 1432 static const unsigned long nmk_pin_sleep_output_modes[] = { 1433 PIN_SLPM_OUTPUT_LOW, 1434 PIN_SLPM_OUTPUT_HIGH, 1435 PIN_SLPM_DIR_OUTPUT, 1436 }; 1437 1438 static const unsigned long nmk_pin_sleep_wakeup_modes[] = { 1439 PIN_SLPM_WAKEUP_DISABLE, 1440 PIN_SLPM_WAKEUP_ENABLE, 1441 }; 1442 1443 static const unsigned long nmk_pin_gpio_modes[] = { 1444 PIN_GPIOMODE_DISABLED, 1445 PIN_GPIOMODE_ENABLED, 1446 }; 1447 1448 static const unsigned long nmk_pin_sleep_pdis_modes[] = { 1449 PIN_SLPM_PDIS_DISABLED, 1450 PIN_SLPM_PDIS_ENABLED, 1451 }; 1452 1453 struct nmk_cfg_param { 1454 const char *property; 1455 unsigned long config; 1456 const unsigned long *choice; 1457 int size; 1458 }; 1459 1460 static const struct nmk_cfg_param nmk_cfg_params[] = { 1461 NMK_CONFIG_PIN_ARRAY("ste,input", nmk_pin_input_modes), 1462 NMK_CONFIG_PIN_ARRAY("ste,output", nmk_pin_output_modes), 1463 NMK_CONFIG_PIN_ARRAY("ste,sleep", nmk_pin_sleep_modes), 1464 NMK_CONFIG_PIN_ARRAY("ste,sleep-input", nmk_pin_sleep_input_modes), 1465 NMK_CONFIG_PIN_ARRAY("ste,sleep-output", nmk_pin_sleep_output_modes), 1466 NMK_CONFIG_PIN_ARRAY("ste,sleep-wakeup", nmk_pin_sleep_wakeup_modes), 1467 NMK_CONFIG_PIN_ARRAY("ste,gpio", nmk_pin_gpio_modes), 1468 NMK_CONFIG_PIN_ARRAY("ste,sleep-pull-disable", nmk_pin_sleep_pdis_modes), 1469 }; 1470 1471 static int nmk_dt_pin_config(int index, int val, unsigned long *config) 1472 { 1473 int ret = 0; 1474 1475 if (nmk_cfg_params[index].choice == NULL) 1476 *config = nmk_cfg_params[index].config; 1477 else { 1478 /* test if out of range */ 1479 if (val < nmk_cfg_params[index].size) { 1480 *config = nmk_cfg_params[index].config | 1481 nmk_cfg_params[index].choice[val]; 1482 } 1483 } 1484 return ret; 1485 } 1486 1487 static const char *nmk_find_pin_name(struct pinctrl_dev *pctldev, const char *pin_name) 1488 { 1489 int i, pin_number; 1490 struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); 1491 1492 if (sscanf((char *)pin_name, "GPIO%d", &pin_number) == 1) 1493 for (i = 0; i < npct->soc->npins; i++) 1494 if (npct->soc->pins[i].number == pin_number) 1495 return npct->soc->pins[i].name; 1496 return NULL; 1497 } 1498 1499 static bool nmk_pinctrl_dt_get_config(struct device_node *np, 1500 unsigned long *configs) 1501 { 1502 bool has_config = 0; 1503 unsigned long cfg = 0; 1504 int i, val, ret; 1505 1506 for (i = 0; i < ARRAY_SIZE(nmk_cfg_params); i++) { 1507 ret = of_property_read_u32(np, 1508 nmk_cfg_params[i].property, &val); 1509 if (ret != -EINVAL) { 1510 if (nmk_dt_pin_config(i, val, &cfg) == 0) { 1511 *configs |= cfg; 1512 has_config = 1; 1513 } 1514 } 1515 } 1516 1517 return has_config; 1518 } 1519 1520 static int nmk_pinctrl_dt_subnode_to_map(struct pinctrl_dev *pctldev, 1521 struct device_node *np, 1522 struct pinctrl_map **map, 1523 unsigned *reserved_maps, 1524 unsigned *num_maps) 1525 { 1526 int ret; 1527 const char *function = NULL; 1528 unsigned long configs = 0; 1529 bool has_config = 0; 1530 struct property *prop; 1531 struct device_node *np_config; 1532 1533 ret = of_property_read_string(np, "function", &function); 1534 if (ret >= 0) { 1535 const char *group; 1536 1537 ret = of_property_count_strings(np, "groups"); 1538 if (ret < 0) 1539 goto exit; 1540 1541 ret = pinctrl_utils_reserve_map(pctldev, map, 1542 reserved_maps, 1543 num_maps, ret); 1544 if (ret < 0) 1545 goto exit; 1546 1547 of_property_for_each_string(np, "groups", prop, group) { 1548 ret = nmk_dt_add_map_mux(map, reserved_maps, num_maps, 1549 group, function); 1550 if (ret < 0) 1551 goto exit; 1552 } 1553 } 1554 1555 has_config = nmk_pinctrl_dt_get_config(np, &configs); 1556 np_config = of_parse_phandle(np, "ste,config", 0); 1557 if (np_config) 1558 has_config |= nmk_pinctrl_dt_get_config(np_config, &configs); 1559 if (has_config) { 1560 const char *gpio_name; 1561 const char *pin; 1562 1563 ret = of_property_count_strings(np, "pins"); 1564 if (ret < 0) 1565 goto exit; 1566 ret = pinctrl_utils_reserve_map(pctldev, map, 1567 reserved_maps, 1568 num_maps, ret); 1569 if (ret < 0) 1570 goto exit; 1571 1572 of_property_for_each_string(np, "pins", prop, pin) { 1573 gpio_name = nmk_find_pin_name(pctldev, pin); 1574 1575 ret = nmk_dt_add_map_configs(map, reserved_maps, 1576 num_maps, 1577 gpio_name, &configs, 1); 1578 if (ret < 0) 1579 goto exit; 1580 } 1581 } 1582 1583 exit: 1584 return ret; 1585 } 1586 1587 static int nmk_pinctrl_dt_node_to_map(struct pinctrl_dev *pctldev, 1588 struct device_node *np_config, 1589 struct pinctrl_map **map, unsigned *num_maps) 1590 { 1591 unsigned reserved_maps; 1592 struct device_node *np; 1593 int ret; 1594 1595 reserved_maps = 0; 1596 *map = NULL; 1597 *num_maps = 0; 1598 1599 for_each_child_of_node(np_config, np) { 1600 ret = nmk_pinctrl_dt_subnode_to_map(pctldev, np, map, 1601 &reserved_maps, num_maps); 1602 if (ret < 0) { 1603 pinctrl_utils_free_map(pctldev, *map, *num_maps); 1604 return ret; 1605 } 1606 } 1607 1608 return 0; 1609 } 1610 1611 static const struct pinctrl_ops nmk_pinctrl_ops = { 1612 .get_groups_count = nmk_get_groups_cnt, 1613 .get_group_name = nmk_get_group_name, 1614 .get_group_pins = nmk_get_group_pins, 1615 .pin_dbg_show = nmk_pin_dbg_show, 1616 .dt_node_to_map = nmk_pinctrl_dt_node_to_map, 1617 .dt_free_map = pinctrl_utils_free_map, 1618 }; 1619 1620 static int nmk_pmx_get_funcs_cnt(struct pinctrl_dev *pctldev) 1621 { 1622 struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); 1623 1624 return npct->soc->nfunctions; 1625 } 1626 1627 static const char *nmk_pmx_get_func_name(struct pinctrl_dev *pctldev, 1628 unsigned function) 1629 { 1630 struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); 1631 1632 return npct->soc->functions[function].name; 1633 } 1634 1635 static int nmk_pmx_get_func_groups(struct pinctrl_dev *pctldev, 1636 unsigned function, 1637 const char * const **groups, 1638 unsigned * const num_groups) 1639 { 1640 struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); 1641 1642 *groups = npct->soc->functions[function].groups; 1643 *num_groups = npct->soc->functions[function].ngroups; 1644 1645 return 0; 1646 } 1647 1648 static int nmk_pmx_set(struct pinctrl_dev *pctldev, unsigned function, 1649 unsigned group) 1650 { 1651 struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); 1652 const struct nmk_pingroup *g; 1653 static unsigned int slpm[NUM_BANKS]; 1654 unsigned long flags = 0; 1655 bool glitch; 1656 int ret = -EINVAL; 1657 int i; 1658 1659 g = &npct->soc->groups[group]; 1660 1661 if (g->altsetting < 0) 1662 return -EINVAL; 1663 1664 dev_dbg(npct->dev, "enable group %s, %u pins\n", g->name, g->npins); 1665 1666 /* 1667 * If we're setting altfunc C by setting both AFSLA and AFSLB to 1, 1668 * we may pass through an undesired state. In this case we take 1669 * some extra care. 1670 * 1671 * Safe sequence used to switch IOs between GPIO and Alternate-C mode: 1672 * - Save SLPM registers (since we have a shadow register in the 1673 * nmk_chip we're using that as backup) 1674 * - Set SLPM=0 for the IOs you want to switch and others to 1 1675 * - Configure the GPIO registers for the IOs that are being switched 1676 * - Set IOFORCE=1 1677 * - Modify the AFLSA/B registers for the IOs that are being switched 1678 * - Set IOFORCE=0 1679 * - Restore SLPM registers 1680 * - Any spurious wake up event during switch sequence to be ignored 1681 * and cleared 1682 * 1683 * We REALLY need to save ALL slpm registers, because the external 1684 * IOFORCE will switch *all* ports to their sleepmode setting to as 1685 * to avoid glitches. (Not just one port!) 1686 */ 1687 glitch = ((g->altsetting & NMK_GPIO_ALT_C) == NMK_GPIO_ALT_C); 1688 1689 if (glitch) { 1690 spin_lock_irqsave(&nmk_gpio_slpm_lock, flags); 1691 1692 /* Initially don't put any pins to sleep when switching */ 1693 memset(slpm, 0xff, sizeof(slpm)); 1694 1695 /* 1696 * Then mask the pins that need to be sleeping now when we're 1697 * switching to the ALT C function. 1698 */ 1699 for (i = 0; i < g->npins; i++) 1700 slpm[g->pins[i] / NMK_GPIO_PER_CHIP] &= ~BIT(g->pins[i]); 1701 nmk_gpio_glitch_slpm_init(slpm); 1702 } 1703 1704 for (i = 0; i < g->npins; i++) { 1705 struct nmk_gpio_chip *nmk_chip; 1706 unsigned bit; 1707 1708 nmk_chip = find_nmk_gpio_from_pin(g->pins[i]); 1709 if (!nmk_chip) { 1710 dev_err(npct->dev, 1711 "invalid pin offset %d in group %s at index %d\n", 1712 g->pins[i], g->name, i); 1713 goto out_glitch; 1714 } 1715 dev_dbg(npct->dev, "setting pin %d to altsetting %d\n", g->pins[i], g->altsetting); 1716 1717 clk_enable(nmk_chip->clk); 1718 bit = g->pins[i] % NMK_GPIO_PER_CHIP; 1719 /* 1720 * If the pin is switching to altfunc, and there was an 1721 * interrupt installed on it which has been lazy disabled, 1722 * actually mask the interrupt to prevent spurious interrupts 1723 * that would occur while the pin is under control of the 1724 * peripheral. Only SKE does this. 1725 */ 1726 nmk_gpio_disable_lazy_irq(nmk_chip, bit); 1727 1728 __nmk_gpio_set_mode_safe(nmk_chip, bit, 1729 (g->altsetting & NMK_GPIO_ALT_C), glitch); 1730 clk_disable(nmk_chip->clk); 1731 1732 /* 1733 * Call PRCM GPIOCR config function in case ALTC 1734 * has been selected: 1735 * - If selection is a ALTCx, some bits in PRCM GPIOCR registers 1736 * must be set. 1737 * - If selection is pure ALTC and previous selection was ALTCx, 1738 * then some bits in PRCM GPIOCR registers must be cleared. 1739 */ 1740 if ((g->altsetting & NMK_GPIO_ALT_C) == NMK_GPIO_ALT_C) 1741 nmk_prcm_altcx_set_mode(npct, g->pins[i], 1742 g->altsetting >> NMK_GPIO_ALT_CX_SHIFT); 1743 } 1744 1745 /* When all pins are successfully reconfigured we get here */ 1746 ret = 0; 1747 1748 out_glitch: 1749 if (glitch) { 1750 nmk_gpio_glitch_slpm_restore(slpm); 1751 spin_unlock_irqrestore(&nmk_gpio_slpm_lock, flags); 1752 } 1753 1754 return ret; 1755 } 1756 1757 static int nmk_gpio_request_enable(struct pinctrl_dev *pctldev, 1758 struct pinctrl_gpio_range *range, 1759 unsigned offset) 1760 { 1761 struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); 1762 struct nmk_gpio_chip *nmk_chip; 1763 struct gpio_chip *chip; 1764 unsigned bit; 1765 1766 if (!range) { 1767 dev_err(npct->dev, "invalid range\n"); 1768 return -EINVAL; 1769 } 1770 if (!range->gc) { 1771 dev_err(npct->dev, "missing GPIO chip in range\n"); 1772 return -EINVAL; 1773 } 1774 chip = range->gc; 1775 nmk_chip = gpiochip_get_data(chip); 1776 1777 dev_dbg(npct->dev, "enable pin %u as GPIO\n", offset); 1778 1779 clk_enable(nmk_chip->clk); 1780 bit = offset % NMK_GPIO_PER_CHIP; 1781 /* There is no glitch when converting any pin to GPIO */ 1782 __nmk_gpio_set_mode(nmk_chip, bit, NMK_GPIO_ALT_GPIO); 1783 clk_disable(nmk_chip->clk); 1784 1785 return 0; 1786 } 1787 1788 static void nmk_gpio_disable_free(struct pinctrl_dev *pctldev, 1789 struct pinctrl_gpio_range *range, 1790 unsigned offset) 1791 { 1792 struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); 1793 1794 dev_dbg(npct->dev, "disable pin %u as GPIO\n", offset); 1795 /* Set the pin to some default state, GPIO is usually default */ 1796 } 1797 1798 static const struct pinmux_ops nmk_pinmux_ops = { 1799 .get_functions_count = nmk_pmx_get_funcs_cnt, 1800 .get_function_name = nmk_pmx_get_func_name, 1801 .get_function_groups = nmk_pmx_get_func_groups, 1802 .set_mux = nmk_pmx_set, 1803 .gpio_request_enable = nmk_gpio_request_enable, 1804 .gpio_disable_free = nmk_gpio_disable_free, 1805 .strict = true, 1806 }; 1807 1808 static int nmk_pin_config_get(struct pinctrl_dev *pctldev, unsigned pin, 1809 unsigned long *config) 1810 { 1811 /* Not implemented */ 1812 return -EINVAL; 1813 } 1814 1815 static int nmk_pin_config_set(struct pinctrl_dev *pctldev, unsigned pin, 1816 unsigned long *configs, unsigned num_configs) 1817 { 1818 static const char *pullnames[] = { 1819 [NMK_GPIO_PULL_NONE] = "none", 1820 [NMK_GPIO_PULL_UP] = "up", 1821 [NMK_GPIO_PULL_DOWN] = "down", 1822 [3] /* illegal */ = "??" 1823 }; 1824 static const char *slpmnames[] = { 1825 [NMK_GPIO_SLPM_INPUT] = "input/wakeup", 1826 [NMK_GPIO_SLPM_NOCHANGE] = "no-change/no-wakeup", 1827 }; 1828 struct nmk_pinctrl *npct = pinctrl_dev_get_drvdata(pctldev); 1829 struct nmk_gpio_chip *nmk_chip; 1830 unsigned bit; 1831 pin_cfg_t cfg; 1832 int pull, slpm, output, val, i; 1833 bool lowemi, gpiomode, sleep; 1834 1835 nmk_chip = find_nmk_gpio_from_pin(pin); 1836 if (!nmk_chip) { 1837 dev_err(npct->dev, 1838 "invalid pin offset %d\n", pin); 1839 return -EINVAL; 1840 } 1841 1842 for (i = 0; i < num_configs; i++) { 1843 /* 1844 * The pin config contains pin number and altfunction fields, 1845 * here we just ignore that part. It's being handled by the 1846 * framework and pinmux callback respectively. 1847 */ 1848 cfg = (pin_cfg_t) configs[i]; 1849 pull = PIN_PULL(cfg); 1850 slpm = PIN_SLPM(cfg); 1851 output = PIN_DIR(cfg); 1852 val = PIN_VAL(cfg); 1853 lowemi = PIN_LOWEMI(cfg); 1854 gpiomode = PIN_GPIOMODE(cfg); 1855 sleep = PIN_SLEEPMODE(cfg); 1856 1857 if (sleep) { 1858 int slpm_pull = PIN_SLPM_PULL(cfg); 1859 int slpm_output = PIN_SLPM_DIR(cfg); 1860 int slpm_val = PIN_SLPM_VAL(cfg); 1861 1862 /* All pins go into GPIO mode at sleep */ 1863 gpiomode = true; 1864 1865 /* 1866 * The SLPM_* values are normal values + 1 to allow zero 1867 * to mean "same as normal". 1868 */ 1869 if (slpm_pull) 1870 pull = slpm_pull - 1; 1871 if (slpm_output) 1872 output = slpm_output - 1; 1873 if (slpm_val) 1874 val = slpm_val - 1; 1875 1876 dev_dbg(nmk_chip->chip.parent, 1877 "pin %d: sleep pull %s, dir %s, val %s\n", 1878 pin, 1879 slpm_pull ? pullnames[pull] : "same", 1880 slpm_output ? (output ? "output" : "input") 1881 : "same", 1882 slpm_val ? (val ? "high" : "low") : "same"); 1883 } 1884 1885 dev_dbg(nmk_chip->chip.parent, 1886 "pin %d [%#lx]: pull %s, slpm %s (%s%s), lowemi %s\n", 1887 pin, cfg, pullnames[pull], slpmnames[slpm], 1888 output ? "output " : "input", 1889 output ? (val ? "high" : "low") : "", 1890 lowemi ? "on" : "off"); 1891 1892 clk_enable(nmk_chip->clk); 1893 bit = pin % NMK_GPIO_PER_CHIP; 1894 if (gpiomode) 1895 /* No glitch when going to GPIO mode */ 1896 __nmk_gpio_set_mode(nmk_chip, bit, NMK_GPIO_ALT_GPIO); 1897 if (output) 1898 __nmk_gpio_make_output(nmk_chip, bit, val); 1899 else { 1900 __nmk_gpio_make_input(nmk_chip, bit); 1901 __nmk_gpio_set_pull(nmk_chip, bit, pull); 1902 } 1903 /* TODO: isn't this only applicable on output pins? */ 1904 __nmk_gpio_set_lowemi(nmk_chip, bit, lowemi); 1905 1906 __nmk_gpio_set_slpm(nmk_chip, bit, slpm); 1907 clk_disable(nmk_chip->clk); 1908 } /* for each config */ 1909 1910 return 0; 1911 } 1912 1913 static const struct pinconf_ops nmk_pinconf_ops = { 1914 .pin_config_get = nmk_pin_config_get, 1915 .pin_config_set = nmk_pin_config_set, 1916 }; 1917 1918 static struct pinctrl_desc nmk_pinctrl_desc = { 1919 .name = "pinctrl-nomadik", 1920 .pctlops = &nmk_pinctrl_ops, 1921 .pmxops = &nmk_pinmux_ops, 1922 .confops = &nmk_pinconf_ops, 1923 .owner = THIS_MODULE, 1924 }; 1925 1926 static const struct of_device_id nmk_pinctrl_match[] = { 1927 { 1928 .compatible = "stericsson,stn8815-pinctrl", 1929 .data = (void *)PINCTRL_NMK_STN8815, 1930 }, 1931 { 1932 .compatible = "stericsson,db8500-pinctrl", 1933 .data = (void *)PINCTRL_NMK_DB8500, 1934 }, 1935 { 1936 .compatible = "stericsson,db8540-pinctrl", 1937 .data = (void *)PINCTRL_NMK_DB8540, 1938 }, 1939 {}, 1940 }; 1941 1942 #ifdef CONFIG_PM_SLEEP 1943 static int nmk_pinctrl_suspend(struct device *dev) 1944 { 1945 struct nmk_pinctrl *npct; 1946 1947 npct = dev_get_drvdata(dev); 1948 if (!npct) 1949 return -EINVAL; 1950 1951 return pinctrl_force_sleep(npct->pctl); 1952 } 1953 1954 static int nmk_pinctrl_resume(struct device *dev) 1955 { 1956 struct nmk_pinctrl *npct; 1957 1958 npct = dev_get_drvdata(dev); 1959 if (!npct) 1960 return -EINVAL; 1961 1962 return pinctrl_force_default(npct->pctl); 1963 } 1964 #endif 1965 1966 static int nmk_pinctrl_probe(struct platform_device *pdev) 1967 { 1968 const struct of_device_id *match; 1969 struct device_node *np = pdev->dev.of_node; 1970 struct device_node *prcm_np; 1971 struct nmk_pinctrl *npct; 1972 unsigned int version = 0; 1973 int i; 1974 1975 npct = devm_kzalloc(&pdev->dev, sizeof(*npct), GFP_KERNEL); 1976 if (!npct) 1977 return -ENOMEM; 1978 1979 match = of_match_device(nmk_pinctrl_match, &pdev->dev); 1980 if (!match) 1981 return -ENODEV; 1982 version = (unsigned int) match->data; 1983 1984 /* Poke in other ASIC variants here */ 1985 if (version == PINCTRL_NMK_STN8815) 1986 nmk_pinctrl_stn8815_init(&npct->soc); 1987 if (version == PINCTRL_NMK_DB8500) 1988 nmk_pinctrl_db8500_init(&npct->soc); 1989 if (version == PINCTRL_NMK_DB8540) 1990 nmk_pinctrl_db8540_init(&npct->soc); 1991 1992 /* 1993 * Since we depend on the GPIO chips to provide clock and register base 1994 * for the pin control operations, make sure that we have these 1995 * populated before we continue. Follow the phandles to instantiate 1996 * them. The GPIO portion of the actual hardware may be probed before 1997 * or after this point: it shouldn't matter as the APIs are orthogonal. 1998 */ 1999 for (i = 0; i < NMK_MAX_BANKS; i++) { 2000 struct device_node *gpio_np; 2001 struct nmk_gpio_chip *nmk_chip; 2002 2003 gpio_np = of_parse_phandle(np, "nomadik-gpio-chips", i); 2004 if (gpio_np) { 2005 dev_info(&pdev->dev, 2006 "populate NMK GPIO %d \"%s\"\n", 2007 i, gpio_np->name); 2008 nmk_chip = nmk_gpio_populate_chip(gpio_np, pdev); 2009 if (IS_ERR(nmk_chip)) 2010 dev_err(&pdev->dev, 2011 "could not populate nmk chip struct " 2012 "- continue anyway\n"); 2013 of_node_put(gpio_np); 2014 } 2015 } 2016 2017 prcm_np = of_parse_phandle(np, "prcm", 0); 2018 if (prcm_np) 2019 npct->prcm_base = of_iomap(prcm_np, 0); 2020 if (!npct->prcm_base) { 2021 if (version == PINCTRL_NMK_STN8815) { 2022 dev_info(&pdev->dev, 2023 "No PRCM base, " 2024 "assuming no ALT-Cx control is available\n"); 2025 } else { 2026 dev_err(&pdev->dev, "missing PRCM base address\n"); 2027 return -EINVAL; 2028 } 2029 } 2030 2031 nmk_pinctrl_desc.pins = npct->soc->pins; 2032 nmk_pinctrl_desc.npins = npct->soc->npins; 2033 npct->dev = &pdev->dev; 2034 2035 npct->pctl = devm_pinctrl_register(&pdev->dev, &nmk_pinctrl_desc, npct); 2036 if (IS_ERR(npct->pctl)) { 2037 dev_err(&pdev->dev, "could not register Nomadik pinctrl driver\n"); 2038 return PTR_ERR(npct->pctl); 2039 } 2040 2041 platform_set_drvdata(pdev, npct); 2042 dev_info(&pdev->dev, "initialized Nomadik pin control driver\n"); 2043 2044 return 0; 2045 } 2046 2047 static const struct of_device_id nmk_gpio_match[] = { 2048 { .compatible = "st,nomadik-gpio", }, 2049 {} 2050 }; 2051 2052 static struct platform_driver nmk_gpio_driver = { 2053 .driver = { 2054 .name = "gpio", 2055 .of_match_table = nmk_gpio_match, 2056 }, 2057 .probe = nmk_gpio_probe, 2058 }; 2059 2060 static SIMPLE_DEV_PM_OPS(nmk_pinctrl_pm_ops, 2061 nmk_pinctrl_suspend, 2062 nmk_pinctrl_resume); 2063 2064 static struct platform_driver nmk_pinctrl_driver = { 2065 .driver = { 2066 .name = "pinctrl-nomadik", 2067 .of_match_table = nmk_pinctrl_match, 2068 .pm = &nmk_pinctrl_pm_ops, 2069 }, 2070 .probe = nmk_pinctrl_probe, 2071 }; 2072 2073 static int __init nmk_gpio_init(void) 2074 { 2075 return platform_driver_register(&nmk_gpio_driver); 2076 } 2077 subsys_initcall(nmk_gpio_init); 2078 2079 static int __init nmk_pinctrl_init(void) 2080 { 2081 return platform_driver_register(&nmk_pinctrl_driver); 2082 } 2083 core_initcall(nmk_pinctrl_init); 2084 2085 MODULE_AUTHOR("Prafulla WADASKAR and Alessandro Rubini"); 2086 MODULE_DESCRIPTION("Nomadik GPIO Driver"); 2087 MODULE_LICENSE("GPL"); 2088