1 /* SPDX-License-Identifier: GPL-2.0-or-later */ 2 /* Copyright (C) 2019 IBM Corp. */ 3 4 #ifndef ASPEED_PINMUX_H 5 #define ASPEED_PINMUX_H 6 7 #include <linux/regmap.h> 8 #include <stdbool.h> 9 10 /* 11 * The ASPEED SoCs provide typically more than 200 pins for GPIO and other 12 * functions. The SoC function enabled on a pin is determined on a priority 13 * basis where a given pin can provide a number of different signal types. 14 * 15 * The signal active on a pin is described by both a priority level and 16 * compound logical expressions involving multiple operators, registers and 17 * bits. Some difficulty arises as the pin's function bit masks for each 18 * priority level are frequently not the same (i.e. cannot just flip a bit to 19 * change from a high to low priority signal), or even in the same register. 20 * Further, not all signals can be unmuxed, as some expressions depend on 21 * values in the hardware strapping register (which may be treated as 22 * read-only). 23 * 24 * SoC Multi-function Pin Expression Examples 25 * ------------------------------------------ 26 * 27 * Here are some sample mux configurations from the AST2400 and AST2500 28 * datasheets to illustrate the corner cases, roughly in order of least to most 29 * corner. The signal priorities are in decending order from P0 (highest). 30 * 31 * D6 is a pin with a single function (beside GPIO); a high priority signal 32 * that participates in one function: 33 * 34 * Ball | Default | P0 Signal | P0 Expression | P1 Signal | P1 Expression | Other 35 * -----+---------+-----------+-----------------------------+-----------+---------------+---------- 36 * D6 GPIOA0 MAC1LINK SCU80[0]=1 GPIOA0 37 * -----+---------+-----------+-----------------------------+-----------+---------------+---------- 38 * 39 * C5 is a multi-signal pin (high and low priority signals). Here we touch 40 * different registers for the different functions that enable each signal: 41 * 42 * -----+---------+-----------+-----------------------------+-----------+---------------+---------- 43 * C5 GPIOA4 SCL9 SCU90[22]=1 TIMER5 SCU80[4]=1 GPIOA4 44 * -----+---------+-----------+-----------------------------+-----------+---------------+---------- 45 * 46 * E19 is a single-signal pin with two functions that influence the active 47 * signal. In this case both bits have the same meaning - enable a dedicated 48 * LPC reset pin. However it's not always the case that the bits in the 49 * OR-relationship have the same meaning. 50 * 51 * -----+---------+-----------+-----------------------------+-----------+---------------+---------- 52 * E19 GPIOB4 LPCRST# SCU80[12]=1 | Strap[14]=1 GPIOB4 53 * -----+---------+-----------+-----------------------------+-----------+---------------+---------- 54 * 55 * For example, pin B19 has a low-priority signal that's enabled by two 56 * distinct SoC functions: A specific SIOPBI bit in register SCUA4, and an ACPI 57 * bit in the STRAP register. The ACPI bit configures signals on pins in 58 * addition to B19. Both of the low priority functions as well as the high 59 * priority function must be disabled for GPIOF1 to be used. 60 * 61 * Ball | Default | P0 Signal | P0 Expression | P1 Signal | P1 Expression | Other 62 * -----+---------+-----------+-----------------------------------------+-----------+----------------------------------------+---------- 63 * B19 GPIOF1 NDCD4 SCU80[25]=1 SIOPBI# SCUA4[12]=1 | Strap[19]=0 GPIOF1 64 * -----+---------+-----------+-----------------------------------------+-----------+----------------------------------------+---------- 65 * 66 * For pin E18, the SoC ANDs the expected state of three bits to determine the 67 * pin's active signal: 68 * 69 * * SCU3C[3]: Enable external SOC reset function 70 * * SCU80[15]: Enable SPICS1# or EXTRST# function pin 71 * * SCU90[31]: Select SPI interface CS# output 72 * 73 * -----+---------+-----------+-----------------------------------------+-----------+----------------------------------------+---------- 74 * E18 GPIOB7 EXTRST# SCU3C[3]=1 & SCU80[15]=1 & SCU90[31]=0 SPICS1# SCU3C[3]=1 & SCU80[15]=1 & SCU90[31]=1 GPIOB7 75 * -----+---------+-----------+-----------------------------------------+-----------+----------------------------------------+---------- 76 * 77 * (Bits SCU3C[3] and SCU80[15] appear to only be used in the expressions for 78 * selecting the signals on pin E18) 79 * 80 * Pin T5 is a multi-signal pin with a more complex configuration: 81 * 82 * Ball | Default | P0 Signal | P0 Expression | P1 Signal | P1 Expression | Other 83 * -----+---------+-----------+------------------------------+-----------+---------------+---------- 84 * T5 GPIOL1 VPIDE SCU90[5:4]!=0 & SCU84[17]=1 NDCD1 SCU84[17]=1 GPIOL1 85 * -----+---------+-----------+------------------------------+-----------+---------------+---------- 86 * 87 * The high priority signal configuration is best thought of in terms of its 88 * exploded form, with reference to the SCU90[5:4] bits: 89 * 90 * * SCU90[5:4]=00: disable 91 * * SCU90[5:4]=01: 18 bits (R6/G6/B6) video mode. 92 * * SCU90[5:4]=10: 24 bits (R8/G8/B8) video mode. 93 * * SCU90[5:4]=11: 30 bits (R10/G10/B10) video mode. 94 * 95 * Re-writing: 96 * 97 * -----+---------+-----------+------------------------------+-----------+---------------+---------- 98 * T5 GPIOL1 VPIDE (SCU90[5:4]=1 & SCU84[17]=1) NDCD1 SCU84[17]=1 GPIOL1 99 * | (SCU90[5:4]=2 & SCU84[17]=1) 100 * | (SCU90[5:4]=3 & SCU84[17]=1) 101 * -----+---------+-----------+------------------------------+-----------+---------------+---------- 102 * 103 * For reference the SCU84[17] bit configure the "UART1 NDCD1 or Video VPIDE 104 * function pin", where the signal itself is determined by whether SCU94[5:4] 105 * is disabled or in one of the 18, 24 or 30bit video modes. 106 * 107 * Other video-input-related pins require an explicit state in SCU90[5:4], e.g. 108 * W1 and U5: 109 * 110 * -----+---------+-----------+------------------------------+-----------+---------------+---------- 111 * W1 GPIOL6 VPIB0 SCU90[5:4]=3 & SCU84[22]=1 TXD1 SCU84[22]=1 GPIOL6 112 * U5 GPIOL7 VPIB1 SCU90[5:4]=3 & SCU84[23]=1 RXD1 SCU84[23]=1 GPIOL7 113 * -----+---------+-----------+------------------------------+-----------+---------------+---------- 114 * 115 * The examples of T5 and W1 are particularly fertile, as they also demonstrate 116 * that despite operating as part of the video input bus each signal needs to 117 * be enabled individually via it's own SCU84 (in the cases of T5 and W1) 118 * register bit. This is a little crazy if the bus doesn't have optional 119 * signals, but is used to decent effect with some of the UARTs where not all 120 * signals are required. However, this isn't done consistently - UART1 is 121 * enabled on a per-pin basis, and by contrast, all signals for UART6 are 122 * enabled by a single bit. 123 * 124 * Further, the high and low priority signals listed in the table above share 125 * a configuration bit. The VPI signals should operate in concert in a single 126 * function, but the UART signals should retain the ability to be configured 127 * independently. This pushes the implementation down the path of tagging a 128 * signal's expressions with the function they participate in, rather than 129 * defining masks affecting multiple signals per function. The latter approach 130 * fails in this instance where applying the configuration for the UART pin of 131 * interest will stomp on the state of other UART signals when disabling the 132 * VPI functions on the current pin. 133 * 134 * Ball | Default | P0 Signal | P0 Expression | P1 Signal | P1 Expression | Other 135 * -----+------------+-----------+---------------------------+-----------+---------------+------------ 136 * A12 RGMII1TXCK GPIOT0 SCUA0[0]=1 RMII1TXEN Strap[6]=0 RGMII1TXCK 137 * B12 RGMII1TXCTL GPIOT1 SCUA0[1]=1 – Strap[6]=0 RGMII1TXCTL 138 * -----+------------+-----------+---------------------------+-----------+---------------+------------ 139 * 140 * A12 demonstrates that the "Other" signal isn't always GPIO - in this case 141 * GPIOT0 is a high-priority signal and RGMII1TXCK is Other. Thus, GPIO 142 * should be treated like any other signal type with full function expression 143 * requirements, and not assumed to be the default case. Separately, GPIOT0 and 144 * GPIOT1's signal descriptor bits are distinct, therefore we must iterate all 145 * pins in the function's group to disable the higher-priority signals such 146 * that the signal for the function of interest is correctly enabled. 147 * 148 * Finally, three priority levels aren't always enough; the AST2500 brings with 149 * it 18 pins of five priority levels, however the 18 pins only use three of 150 * the five priority levels. 151 * 152 * Ultimately the requirement to control pins in the examples above drive the 153 * design: 154 * 155 * * Pins provide signals according to functions activated in the mux 156 * configuration 157 * 158 * * Pins provide up to five signal types in a priority order 159 * 160 * * For priorities levels defined on a pin, each priority provides one signal 161 * 162 * * Enabling lower priority signals requires higher priority signals be 163 * disabled 164 * 165 * * A function represents a set of signals; functions are distinct if they 166 * do not share a subset of signals (and may be distinct if they are a 167 * strict subset). 168 * 169 * * Signals participate in one or more functions or groups 170 * 171 * * A function is described by an expression of one or more signal 172 * descriptors, which compare bit values in a register 173 * 174 * * A signal expression is the smallest set of signal descriptors whose 175 * comparisons must evaluate 'true' for a signal to be enabled on a pin. 176 * 177 * * A signal participating in a function is active on a pin if evaluating all 178 * signal descriptors in the pin's signal expression for the function yields 179 * a 'true' result 180 * 181 * * A signal at a given priority on a given pin is active if any of the 182 * functions in which the signal participates are active, and no higher 183 * priority signal on the pin is active 184 * 185 * * GPIO is configured per-pin 186 * 187 * And so: 188 * 189 * * To disable a signal, any function(s) activating the signal must be 190 * disabled 191 * 192 * * Each pin must know the signal expressions of functions in which it 193 * participates, for the purpose of enabling the Other function. This is done 194 * by deactivating all functions that activate higher priority signals on the 195 * pin. 196 * 197 * As a concrete example: 198 * 199 * * T5 provides three signals types: VPIDE, NDCD1 and GPIO 200 * 201 * * The VPIDE signal participates in 3 functions: VPI18, VPI24 and VPI30 202 * 203 * * The NDCD1 signal participates in just its own NDCD1 function 204 * 205 * * VPIDE is high priority, NDCD1 is low priority, and GPIOL1 is the least 206 * prioritised 207 * 208 * * The prerequisit for activating the NDCD1 signal is that the VPI18, VPI24 209 * and VPI30 functions all be disabled 210 * 211 * * Similarly, all of VPI18, VPI24, VPI30 and NDCD1 functions must be disabled 212 * to provide GPIOL6 213 * 214 * Considerations 215 * -------------- 216 * 217 * If pinctrl allows us to allocate a pin we can configure a function without 218 * concern for the function of already allocated pins, if pin groups are 219 * created with respect to the SoC functions in which they participate. This is 220 * intuitive, but it did not feel obvious from the bit/pin relationships. 221 * 222 * Conversely, failing to allocate all pins in a group indicates some bits (as 223 * well as pins) required for the group's configuration will already be in use, 224 * likely in a way that's inconsistent with the requirements of the failed 225 * group. 226 * 227 * Implementation 228 * -------------- 229 * 230 * Beyond the documentation below the various structures and helper macros that 231 * allow the implementation to hang together are defined. The macros are fairly 232 * dense, so below we walk through some raw examples of the configuration 233 * tables in an effort to clarify the concepts. 234 * 235 * The complexity of configuring the mux combined with the scale of the pins 236 * and functions was a concern, so the table design along with the macro jungle 237 * is an attempt to address it. The rough principles of the approach are: 238 * 239 * 1. Use a data-driven solution rather than embedding state into code 240 * 2. Minimise editing to the specifics of the given mux configuration 241 * 3. Detect as many errors as possible at compile time 242 * 243 * Addressing point 3 leads to naming of symbols in terms of the four 244 * properties associated with a given mux configuration: The pin, the signal, 245 * the group and the function. In this way copy/paste errors cause duplicate 246 * symbols to be defined, which prevents successful compilation. Failing to 247 * properly parent the tables leads to unused symbol warnings, and use of 248 * designated initialisers and additional warnings ensures that there are 249 * no override errors in the pin, group and function arrays. 250 * 251 * Addressing point 2 drives the development of the macro jungle, as it 252 * centralises the definition noise at the cost of taking some time to 253 * understand. 254 * 255 * Here's a complete, concrete "pre-processed" example of the table structures 256 * used to describe the D6 ball from the examples above: 257 * 258 * ``` 259 * static const struct aspeed_sig_desc sig_descs_MAC1LINK_MAC1LINK[] = { 260 * { 261 * .ip = ASPEED_IP_SCU, 262 * .reg = 0x80, 263 * .mask = BIT(0), 264 * .enable = 1, 265 * .disable = 0 266 * }, 267 * }; 268 * 269 * static const struct aspeed_sig_expr sig_expr_MAC1LINK_MAC1LINK = { 270 * .signal = "MAC1LINK", 271 * .function = "MAC1LINK", 272 * .ndescs = ARRAY_SIZE(sig_descs_MAC1LINK_MAC1LINK), 273 * .descs = &(sig_descs_MAC1LINK_MAC1LINK)[0], 274 * }; 275 * 276 * static const struct aspeed_sig_expr *sig_exprs_MAC1LINK_MAC1LINK[] = { 277 * &sig_expr_MAC1LINK_MAC1LINK, 278 * NULL, 279 * }; 280 * 281 * static const struct aspeed_sig_desc sig_descs_GPIOA0_GPIOA0[] = { }; 282 * 283 * static const struct aspeed_sig_expr sig_expr_GPIOA0_GPIOA0 = { 284 * .signal = "GPIOA0", 285 * .function = "GPIOA0", 286 * .ndescs = ARRAY_SIZE(sig_descs_GPIOA0_GPIOA0), 287 * .descs = &(sig_descs_GPIOA0_GPIOA0)[0], 288 * }; 289 * 290 * static const struct aspeed_sig_expr *sig_exprs_GPIOA0_GPIOA0[] = { 291 * &sig_expr_GPIOA0_GPIOA0, 292 * NULL 293 * }; 294 * 295 * static const struct aspeed_sig_expr **pin_exprs_0[] = { 296 * sig_exprs_MAC1LINK_MAC1LINK, 297 * sig_exprs_GPIOA0_GPIOA0, 298 * NULL 299 * }; 300 * 301 * static const struct aspeed_pin_desc pin_0 = { "0", (&pin_exprs_0[0]) }; 302 * static const int group_pins_MAC1LINK[] = { 0 }; 303 * static const char *func_groups_MAC1LINK[] = { "MAC1LINK" }; 304 * 305 * static struct pinctrl_pin_desc aspeed_g4_pins[] = { 306 * [0] = { .number = 0, .name = "D6", .drv_data = &pin_0 }, 307 * }; 308 * 309 * static const struct aspeed_pin_group aspeed_g4_groups[] = { 310 * { 311 * .name = "MAC1LINK", 312 * .pins = &(group_pins_MAC1LINK)[0], 313 * .npins = ARRAY_SIZE(group_pins_MAC1LINK), 314 * }, 315 * }; 316 * 317 * static const struct aspeed_pin_function aspeed_g4_functions[] = { 318 * { 319 * .name = "MAC1LINK", 320 * .groups = &func_groups_MAC1LINK[0], 321 * .ngroups = ARRAY_SIZE(func_groups_MAC1LINK), 322 * }, 323 * }; 324 * ``` 325 * 326 * At the end of the day much of the above code is compressed into the 327 * following two lines: 328 * 329 * ``` 330 * #define D6 0 331 * SSSF_PIN_DECL(D6, GPIOA0, MAC1LINK, SIG_DESC_SET(SCU80, 0)); 332 * ``` 333 * 334 * The two examples below show just the differences from the example above. 335 * 336 * Ball E18 demonstrates a function, EXTRST, that requires multiple descriptors 337 * be set for it to be muxed: 338 * 339 * ``` 340 * static const struct aspeed_sig_desc sig_descs_EXTRST_EXTRST[] = { 341 * { 342 * .ip = ASPEED_IP_SCU, 343 * .reg = 0x3C, 344 * .mask = BIT(3), 345 * .enable = 1, 346 * .disable = 0 347 * }, 348 * { 349 * .ip = ASPEED_IP_SCU, 350 * .reg = 0x80, 351 * .mask = BIT(15), 352 * .enable = 1, 353 * .disable = 0 354 * }, 355 * { 356 * .ip = ASPEED_IP_SCU, 357 * .reg = 0x90, 358 * .mask = BIT(31), 359 * .enable = 0, 360 * .disable = 1 361 * }, 362 * }; 363 * 364 * static const struct aspeed_sig_expr sig_expr_EXTRST_EXTRST = { 365 * .signal = "EXTRST", 366 * .function = "EXTRST", 367 * .ndescs = ARRAY_SIZE(sig_descs_EXTRST_EXTRST), 368 * .descs = &(sig_descs_EXTRST_EXTRST)[0], 369 * }; 370 * ... 371 * ``` 372 * 373 * For ball E19, we have multiple functions enabling a single signal, LPCRST#. 374 * The data structures look like: 375 * 376 * static const struct aspeed_sig_desc sig_descs_LPCRST_LPCRST[] = { 377 * { 378 * .ip = ASPEED_IP_SCU, 379 * .reg = 0x80, 380 * .mask = BIT(12), 381 * .enable = 1, 382 * .disable = 0 383 * }, 384 * }; 385 * 386 * static const struct aspeed_sig_expr sig_expr_LPCRST_LPCRST = { 387 * .signal = "LPCRST", 388 * .function = "LPCRST", 389 * .ndescs = ARRAY_SIZE(sig_descs_LPCRST_LPCRST), 390 * .descs = &(sig_descs_LPCRST_LPCRST)[0], 391 * }; 392 * 393 * static const struct aspeed_sig_desc sig_descs_LPCRST_LPCRSTS[] = { 394 * { 395 * .ip = ASPEED_IP_SCU, 396 * .reg = 0x70, 397 * .mask = BIT(14), 398 * .enable = 1, 399 * .disable = 0 400 * }, 401 * }; 402 * 403 * static const struct aspeed_sig_expr sig_expr_LPCRST_LPCRSTS = { 404 * .signal = "LPCRST", 405 * .function = "LPCRSTS", 406 * .ndescs = ARRAY_SIZE(sig_descs_LPCRST_LPCRSTS), 407 * .descs = &(sig_descs_LPCRST_LPCRSTS)[0], 408 * }; 409 * 410 * static const struct aspeed_sig_expr *sig_exprs_LPCRST_LPCRST[] = { 411 * &sig_expr_LPCRST_LPCRST, 412 * &sig_expr_LPCRST_LPCRSTS, 413 * NULL, 414 * }; 415 * ... 416 * ``` 417 * 418 * Both expressions listed in the sig_exprs_LPCRST_LPCRST array need to be set 419 * to disabled for the associated GPIO to be muxed. 420 * 421 */ 422 423 #define ASPEED_IP_SCU 0 424 #define ASPEED_IP_GFX 1 425 #define ASPEED_IP_LPC 2 426 #define ASPEED_NR_PINMUX_IPS 3 427 428 /** 429 * A signal descriptor, which describes the register, bits and the 430 * enable/disable values that should be compared or written. 431 * 432 * @ip: The IP block identifier, used as an index into the regmap array in 433 * struct aspeed_pinctrl_data 434 * @reg: The register offset with respect to the base address of the IP block 435 * @mask: The mask to apply to the register. The lowest set bit of the mask is 436 * used to derive the shift value. 437 * @enable: The value that enables the function. Value should be in the LSBs, 438 * not at the position of the mask. 439 * @disable: The value that disables the function. Value should be in the 440 * LSBs, not at the position of the mask. 441 */ 442 struct aspeed_sig_desc { 443 unsigned int ip; 444 unsigned int reg; 445 u32 mask; 446 u32 enable; 447 u32 disable; 448 }; 449 450 /** 451 * Describes a signal expression. The expression is evaluated by ANDing the 452 * evaluation of the descriptors. 453 * 454 * @signal: The signal name for the priority level on the pin. If the signal 455 * type is GPIO, then the signal name must begin with the 456 * prefix "GPI", e.g. GPIOA0, GPIT0 etc. 457 * @function: The name of the function the signal participates in for the 458 * associated expression. For pin-specific GPIO, the function 459 * name must match the signal name. 460 * @ndescs: The number of signal descriptors in the expression 461 * @descs: Pointer to an array of signal descriptors that comprise the 462 * function expression 463 */ 464 struct aspeed_sig_expr { 465 const char *signal; 466 const char *function; 467 int ndescs; 468 const struct aspeed_sig_desc *descs; 469 }; 470 471 /** 472 * A struct capturing the list of expressions enabling signals at each priority 473 * for a given pin. The signal configuration for a priority level is evaluated 474 * by ORing the evaluation of the signal expressions in the respective 475 * priority's list. 476 * 477 * @name: A name for the pin 478 * @prios: A pointer to an array of expression list pointers 479 * 480 */ 481 struct aspeed_pin_desc { 482 const char *name; 483 const struct aspeed_sig_expr ***prios; 484 }; 485 486 /* Macro hell */ 487 488 #define SIG_DESC_IP_BIT(ip, reg, idx, val) \ 489 { ip, reg, BIT_MASK(idx), val, (((val) + 1) & 1) } 490 491 /** 492 * Short-hand macro for describing an SCU descriptor enabled by the state of 493 * one bit. The disable value is derived. 494 * 495 * @reg: The signal's associated register, offset from base 496 * @idx: The signal's bit index in the register 497 * @val: The value (0 or 1) that enables the function 498 */ 499 #define SIG_DESC_BIT(reg, idx, val) \ 500 SIG_DESC_IP_BIT(ASPEED_IP_SCU, reg, idx, val) 501 502 #define SIG_DESC_IP_SET(ip, reg, idx) SIG_DESC_IP_BIT(ip, reg, idx, 1) 503 504 /** 505 * A further short-hand macro expanding to an SCU descriptor enabled by a set 506 * bit. 507 * 508 * @reg: The register, offset from base 509 * @idx: The bit index in the register 510 */ 511 #define SIG_DESC_SET(reg, idx) SIG_DESC_IP_BIT(ASPEED_IP_SCU, reg, idx, 1) 512 #define SIG_DESC_CLEAR(reg, idx) { ASPEED_IP_SCU, reg, BIT_MASK(idx), 0, 0 } 513 514 #define SIG_DESC_LIST_SYM(sig, group) sig_descs_ ## sig ## _ ## group 515 #define SIG_DESC_LIST_DECL(sig, group, ...) \ 516 static const struct aspeed_sig_desc SIG_DESC_LIST_SYM(sig, group)[] = \ 517 { __VA_ARGS__ } 518 519 #define SIG_EXPR_SYM(sig, group) sig_expr_ ## sig ## _ ## group 520 #define SIG_EXPR_DECL_(sig, group, func) \ 521 static const struct aspeed_sig_expr SIG_EXPR_SYM(sig, group) = \ 522 { \ 523 .signal = #sig, \ 524 .function = #func, \ 525 .ndescs = ARRAY_SIZE(SIG_DESC_LIST_SYM(sig, group)), \ 526 .descs = &(SIG_DESC_LIST_SYM(sig, group))[0], \ 527 } 528 529 /** 530 * Declare a signal expression. 531 * 532 * @sig: A macro symbol name for the signal (is subjected to stringification 533 * and token pasting) 534 * @func: The function in which the signal is participating 535 * @...: Signal descriptors that define the signal expression 536 * 537 * For example, the following declares the ROMD8 signal for the ROM16 function: 538 * 539 * SIG_EXPR_DECL(ROMD8, ROM16, ROM16, SIG_DESC_SET(SCU90, 6)); 540 * 541 * And with multiple signal descriptors: 542 * 543 * SIG_EXPR_DECL(ROMD8, ROM16S, ROM16S, SIG_DESC_SET(HW_STRAP1, 4), 544 * { HW_STRAP1, GENMASK(1, 0), 0, 0 }); 545 */ 546 #define SIG_EXPR_DECL(sig, group, func, ...) \ 547 SIG_DESC_LIST_DECL(sig, group, __VA_ARGS__); \ 548 SIG_EXPR_DECL_(sig, group, func) 549 550 /** 551 * Declare a pointer to a signal expression 552 * 553 * @sig: The macro symbol name for the signal (subjected to token pasting) 554 * @func: The macro symbol name for the function (subjected to token pasting) 555 */ 556 #define SIG_EXPR_PTR(sig, group) (&SIG_EXPR_SYM(sig, group)) 557 558 #define SIG_EXPR_LIST_SYM(sig, group) sig_exprs_ ## sig ## _ ## group 559 560 /** 561 * Declare a signal expression list for reference in a struct aspeed_pin_prio. 562 * 563 * @sig: A macro symbol name for the signal (is subjected to token pasting) 564 * @...: Signal expression structure pointers (use SIG_EXPR_PTR()) 565 * 566 * For example, the 16-bit ROM bus can be enabled by one of two possible signal 567 * expressions: 568 * 569 * SIG_EXPR_DECL(ROMD8, ROM16, ROM16, SIG_DESC_SET(SCU90, 6)); 570 * SIG_EXPR_DECL(ROMD8, ROM16S, ROM16S, SIG_DESC_SET(HW_STRAP1, 4), 571 * { HW_STRAP1, GENMASK(1, 0), 0, 0 }); 572 * SIG_EXPR_LIST_DECL(ROMD8, SIG_EXPR_PTR(ROMD8, ROM16), 573 * SIG_EXPR_PTR(ROMD8, ROM16S)); 574 */ 575 #define SIG_EXPR_LIST_DECL(sig, group, ...) \ 576 static const struct aspeed_sig_expr *SIG_EXPR_LIST_SYM(sig, group)[] =\ 577 { __VA_ARGS__, NULL } 578 579 #define stringify(x) #x 580 #define istringify(x) stringify(x) 581 582 /** 583 * Create an expression symbol alias from (signal, group) to (pin, signal). 584 * 585 * @pin: The pin number 586 * @sig: The signal name 587 * @group: The name of the group of which the pin is a member that is 588 * associated with the function's signal 589 * 590 * Using an alias in this way enables detection of copy/paste errors (defining 591 * the signal for a group multiple times) whilst enabling multiple pin groups 592 * to exist for a signal without intrusive side-effects on defining the list of 593 * signals available on a pin. 594 */ 595 #define SIG_EXPR_LIST_ALIAS(pin, sig, group) \ 596 static const struct aspeed_sig_expr *\ 597 SIG_EXPR_LIST_SYM(pin, sig)[ARRAY_SIZE(SIG_EXPR_LIST_SYM(sig, group))] \ 598 __attribute__((alias(istringify(SIG_EXPR_LIST_SYM(sig, group))))) 599 600 /** 601 * A short-hand macro for declaring a function expression and an expression 602 * list with a single expression (SE) and a single group (SG) of pins. 603 * 604 * @pin: The pin the signal will be routed to 605 * @sig: The signal that will be routed to the pin for the function 606 * @func: A macro symbol name for the function 607 * @...: Function descriptors that define the function expression 608 * 609 * For example, signal NCTS6 participates in its own function with one group: 610 * 611 * SIG_EXPR_LIST_DECL_SINGLE(A18, NCTS6, NCTS6, SIG_DESC_SET(SCU90, 7)); 612 */ 613 #define SIG_EXPR_LIST_DECL_SESG(pin, sig, func, ...) \ 614 SIG_DESC_LIST_DECL(sig, func, __VA_ARGS__); \ 615 SIG_EXPR_DECL_(sig, func, func); \ 616 SIG_EXPR_LIST_DECL(sig, func, SIG_EXPR_PTR(sig, func)); \ 617 SIG_EXPR_LIST_ALIAS(pin, sig, func) 618 619 /** 620 * Similar to the above, but for pins with a single expression (SE) and 621 * multiple groups (MG) of pins. 622 * 623 * @pin: The pin the signal will be routed to 624 * @sig: The signal that will be routed to the pin for the function 625 * @group: The name of the function's pin group in which the pin participates 626 * @func: A macro symbol name for the function 627 * @...: Function descriptors that define the function expression 628 */ 629 #define SIG_EXPR_LIST_DECL_SEMG(pin, sig, group, func, ...) \ 630 SIG_DESC_LIST_DECL(sig, group, __VA_ARGS__); \ 631 SIG_EXPR_DECL_(sig, group, func); \ 632 SIG_EXPR_LIST_DECL(sig, group, SIG_EXPR_PTR(sig, group)); \ 633 SIG_EXPR_LIST_ALIAS(pin, sig, group) 634 635 /** 636 * Similar to the above, but for pins with a dual expressions (DE) and 637 * and a single group (SG) of pins. 638 * 639 * @pin: The pin the signal will be routed to 640 * @sig: The signal that will be routed to the pin for the function 641 * @group: The name of the function's pin group in which the pin participates 642 * @func: A macro symbol name for the function 643 * @...: Function descriptors that define the function expression 644 */ 645 #define SIG_EXPR_LIST_DECL_DESG(pin, sig, f0, f1) \ 646 SIG_EXPR_LIST_DECL(sig, f0, \ 647 SIG_EXPR_PTR(sig, f0), \ 648 SIG_EXPR_PTR(sig, f1)); \ 649 SIG_EXPR_LIST_ALIAS(pin, sig, f0) 650 651 #define SIG_EXPR_LIST_PTR(sig, group) SIG_EXPR_LIST_SYM(sig, group) 652 653 #define PIN_EXPRS_SYM(pin) pin_exprs_ ## pin 654 #define PIN_EXPRS_PTR(pin) (&PIN_EXPRS_SYM(pin)[0]) 655 #define PIN_SYM(pin) pin_ ## pin 656 657 #define PIN_DECL_(pin, ...) \ 658 static const struct aspeed_sig_expr **PIN_EXPRS_SYM(pin)[] = \ 659 { __VA_ARGS__, NULL }; \ 660 static const struct aspeed_pin_desc PIN_SYM(pin) = \ 661 { #pin, PIN_EXPRS_PTR(pin) } 662 663 /** 664 * Declare a single signal pin 665 * 666 * @pin: The pin number 667 * @other: Macro name for "other" functionality (subjected to stringification) 668 * @sig: Macro name for the signal (subjected to stringification) 669 * 670 * For example: 671 * 672 * #define E3 80 673 * SIG_EXPR_LIST_DECL_SINGLE(SCL5, I2C5, I2C5_DESC); 674 * PIN_DECL_1(E3, GPIOK0, SCL5); 675 */ 676 #define PIN_DECL_1(pin, other, sig) \ 677 SIG_EXPR_LIST_DECL_SESG(pin, other, other); \ 678 PIN_DECL_(pin, SIG_EXPR_LIST_PTR(pin, sig), \ 679 SIG_EXPR_LIST_PTR(pin, other)) 680 681 /** 682 * Single signal, single function pin declaration 683 * 684 * @pin: The pin number 685 * @other: Macro name for "other" functionality (subjected to stringification) 686 * @sig: Macro name for the signal (subjected to stringification) 687 * @...: Signal descriptors that define the function expression 688 * 689 * For example: 690 * 691 * SSSF_PIN_DECL(A4, GPIOA2, TIMER3, SIG_DESC_SET(SCU80, 2)); 692 */ 693 #define SSSF_PIN_DECL(pin, other, sig, ...) \ 694 SIG_EXPR_LIST_DECL_SESG(pin, sig, sig, __VA_ARGS__); \ 695 SIG_EXPR_LIST_DECL_SESG(pin, other, other); \ 696 PIN_DECL_(pin, SIG_EXPR_LIST_PTR(pin, sig), \ 697 SIG_EXPR_LIST_PTR(pin, other)); \ 698 FUNC_GROUP_DECL(sig, pin) 699 /** 700 * Declare a two-signal pin 701 * 702 * @pin: The pin number 703 * @other: Macro name for "other" functionality (subjected to stringification) 704 * @high: Macro name for the highest priority signal functions 705 * @low: Macro name for the low signal functions 706 * 707 * For example: 708 * 709 * #define A8 56 710 * SIG_EXPR_DECL(ROMD8, ROM16, SIG_DESC_SET(SCU90, 6)); 711 * SIG_EXPR_DECL(ROMD8, ROM16S, SIG_DESC_SET(HW_STRAP1, 4), 712 * { HW_STRAP1, GENMASK(1, 0), 0, 0 }); 713 * SIG_EXPR_LIST_DECL(ROMD8, SIG_EXPR_PTR(ROMD8, ROM16), 714 * SIG_EXPR_PTR(ROMD8, ROM16S)); 715 * SIG_EXPR_LIST_DECL_SINGLE(NCTS6, NCTS6, SIG_DESC_SET(SCU90, 7)); 716 * PIN_DECL_2(A8, GPIOH0, ROMD8, NCTS6); 717 */ 718 #define PIN_DECL_2(pin, other, high, low) \ 719 SIG_EXPR_LIST_DECL_SESG(pin, other, other); \ 720 PIN_DECL_(pin, \ 721 SIG_EXPR_LIST_PTR(pin, high), \ 722 SIG_EXPR_LIST_PTR(pin, low), \ 723 SIG_EXPR_LIST_PTR(pin, other)) 724 725 #define PIN_DECL_3(pin, other, high, medium, low) \ 726 SIG_EXPR_LIST_DECL_SESG(pin, other, other); \ 727 PIN_DECL_(pin, \ 728 SIG_EXPR_LIST_PTR(pin, high), \ 729 SIG_EXPR_LIST_PTR(pin, medium), \ 730 SIG_EXPR_LIST_PTR(pin, low), \ 731 SIG_EXPR_LIST_PTR(pin, other)) 732 733 #define GROUP_SYM(group) group_pins_ ## group 734 #define GROUP_DECL(group, ...) \ 735 static const int GROUP_SYM(group)[] = { __VA_ARGS__ } 736 737 #define FUNC_SYM(func) func_groups_ ## func 738 #define FUNC_DECL_(func, ...) \ 739 static const char *FUNC_SYM(func)[] = { __VA_ARGS__ } 740 741 #define FUNC_DECL_1(func, group) FUNC_DECL_(func, #group) 742 #define FUNC_DECL_2(func, one, two) FUNC_DECL_(func, #one, #two) 743 #define FUNC_DECL_3(func, one, two, three) FUNC_DECL_(func, #one, #two, #three) 744 745 #define FUNC_GROUP_DECL(func, ...) \ 746 GROUP_DECL(func, __VA_ARGS__); \ 747 FUNC_DECL_(func, #func) 748 749 750 #define GPIO_PIN_DECL(pin, gpio) \ 751 SIG_EXPR_LIST_DECL_SESG(pin, gpio, gpio); \ 752 PIN_DECL_(pin, SIG_EXPR_LIST_PTR(pin, gpio)) 753 754 struct aspeed_pin_group { 755 const char *name; 756 const unsigned int *pins; 757 const unsigned int npins; 758 }; 759 760 #define ASPEED_PINCTRL_GROUP(name_) { \ 761 .name = #name_, \ 762 .pins = &(GROUP_SYM(name_))[0], \ 763 .npins = ARRAY_SIZE(GROUP_SYM(name_)), \ 764 } 765 766 struct aspeed_pin_function { 767 const char *name; 768 const char *const *groups; 769 unsigned int ngroups; 770 }; 771 772 #define ASPEED_PINCTRL_FUNC(name_, ...) { \ 773 .name = #name_, \ 774 .groups = &FUNC_SYM(name_)[0], \ 775 .ngroups = ARRAY_SIZE(FUNC_SYM(name_)), \ 776 } 777 778 struct aspeed_pinmux_data; 779 780 struct aspeed_pinmux_ops { 781 int (*eval)(struct aspeed_pinmux_data *ctx, 782 const struct aspeed_sig_expr *expr, bool enabled); 783 int (*set)(struct aspeed_pinmux_data *ctx, 784 const struct aspeed_sig_expr *expr, bool enabled); 785 }; 786 787 struct aspeed_pinmux_data { 788 struct device *dev; 789 struct regmap *maps[ASPEED_NR_PINMUX_IPS]; 790 791 const struct aspeed_pinmux_ops *ops; 792 793 const struct aspeed_pin_group *groups; 794 const unsigned int ngroups; 795 796 const struct aspeed_pin_function *functions; 797 const unsigned int nfunctions; 798 }; 799 800 int aspeed_sig_desc_eval(const struct aspeed_sig_desc *desc, bool enabled, 801 struct regmap *map); 802 803 int aspeed_sig_expr_eval(struct aspeed_pinmux_data *ctx, 804 const struct aspeed_sig_expr *expr, bool enabled); 805 806 static inline int aspeed_sig_expr_set(struct aspeed_pinmux_data *ctx, 807 const struct aspeed_sig_expr *expr, 808 bool enabled) 809 { 810 return ctx->ops->set(ctx, expr, enabled); 811 } 812 813 #endif /* ASPEED_PINMUX_H */ 814