1 # SPDX-License-Identifier: GPL-2.0-only 2 # 3 # Phy drivers for TI platforms 4 # 5 config PHY_DA8XX_USB 6 tristate "TI DA8xx USB PHY Driver" 7 depends on ARCH_DAVINCI_DA8XX || COMPILE_TEST 8 select GENERIC_PHY 9 select MFD_SYSCON 10 help 11 Enable this to support the USB PHY on DA8xx SoCs. 12 13 This driver controls both the USB 1.1 PHY and the USB 2.0 PHY. 14 15 config PHY_DM816X_USB 16 tristate "TI dm816x USB PHY driver" 17 depends on ARCH_OMAP2PLUS || COMPILE_TEST 18 depends on USB_SUPPORT 19 select GENERIC_PHY 20 select USB_PHY 21 help 22 Enable this for dm816x USB to work. 23 24 config PHY_AM654_SERDES 25 tristate "TI AM654 SERDES support" 26 depends on OF && (ARCH_K3 || COMPILE_TEST) 27 depends on COMMON_CLK 28 select GENERIC_PHY 29 select MULTIPLEXER 30 select REGMAP_MMIO 31 select MUX_MMIO 32 help 33 This option enables support for TI AM654 SerDes PHY used for 34 PCIe. 35 36 config PHY_J721E_WIZ 37 tristate "TI J721E WIZ (SERDES Wrapper) support" 38 depends on OF && (ARCH_K3 || COMPILE_TEST) 39 depends on HAS_IOMEM && OF_ADDRESS 40 depends on COMMON_CLK 41 select GENERIC_PHY 42 select MULTIPLEXER 43 select REGMAP_MMIO 44 select MUX_MMIO 45 help 46 This option enables support for WIZ module present in TI's J721E 47 SoC. WIZ is a serdes wrapper used to configure some of the input 48 signals to the SERDES (Sierra/Torrent). This driver configures 49 three clock selects (pll0, pll1, dig) and resets for each of the 50 lanes. 51 52 config OMAP_CONTROL_PHY 53 tristate "OMAP CONTROL PHY Driver" 54 depends on ARCH_OMAP2PLUS || COMPILE_TEST 55 help 56 Enable this to add support for the PHY part present in the control 57 module. This driver has API to power on the USB2 PHY and to write to 58 the mailbox. The mailbox is present only in omap4 and the register to 59 power on the USB2 PHY is present in OMAP4 and OMAP5. OMAP5 has an 60 additional register to power on USB3 PHY/SATA PHY/PCIE PHY 61 (PIPE3 PHY). 62 63 config OMAP_USB2 64 tristate "OMAP USB2 PHY Driver" 65 depends on ARCH_OMAP2PLUS || ARCH_K3 66 depends on USB_SUPPORT 67 select GENERIC_PHY 68 select USB_PHY 69 select OMAP_CONTROL_PHY if ARCH_OMAP2PLUS || COMPILE_TEST 70 help 71 Enable this to support the transceiver that is part of SOC. This 72 driver takes care of all the PHY functionality apart from comparator. 73 The USB OTG controller communicates with the comparator using this 74 driver. 75 76 config TI_PIPE3 77 tristate "TI PIPE3 PHY Driver" 78 depends on ARCH_OMAP2PLUS || COMPILE_TEST 79 select GENERIC_PHY 80 select OMAP_CONTROL_PHY 81 help 82 Enable this to support the PIPE3 PHY that is part of TI SOCs. This 83 driver takes care of all the PHY functionality apart from comparator. 84 This driver interacts with the "OMAP Control PHY Driver" to power 85 on/off the PHY. 86 87 config PHY_TUSB1210 88 tristate "TI TUSB1210 ULPI PHY module" 89 depends on USB_ULPI_BUS 90 select GENERIC_PHY 91 help 92 Support for TI TUSB1210 USB ULPI PHY. 93 94 config TWL4030_USB 95 tristate "TWL4030 USB Transceiver Driver" 96 depends on TWL4030_CORE && REGULATOR_TWL4030 && USB_MUSB_OMAP2PLUS 97 depends on USB_SUPPORT 98 depends on USB_GADGET || !USB_GADGET # if USB_GADGET=m, this can't 'y' 99 select GENERIC_PHY 100 select USB_PHY 101 help 102 Enable this to support the USB OTG transceiver on TWL4030 103 family chips (including the TWL5030 and TPS659x0 devices). 104 This transceiver supports high and full speed devices plus, 105 in host mode, low speed. 106 107 config PHY_TI_GMII_SEL 108 tristate 109 select GENERIC_PHY 110 select REGMAP 111 help 112 This driver supports configuring of the TI CPSW Port mode depending on 113 the Ethernet PHY connected to the CPSW Port. 114