1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Copyright (c) 2017, 2019, The Linux Foundation. All rights reserved. 4 */ 5 6 #include <linux/clk.h> 7 #include <linux/delay.h> 8 #include <linux/err.h> 9 #include <linux/io.h> 10 #include <linux/kernel.h> 11 #include <linux/mfd/syscon.h> 12 #include <linux/module.h> 13 #include <linux/nvmem-consumer.h> 14 #include <linux/of.h> 15 #include <linux/of_device.h> 16 #include <linux/phy/phy.h> 17 #include <linux/platform_device.h> 18 #include <linux/regmap.h> 19 #include <linux/regulator/consumer.h> 20 #include <linux/reset.h> 21 #include <linux/slab.h> 22 23 #include <dt-bindings/phy/phy-qcom-qusb2.h> 24 25 #define QUSB2PHY_PLL_TEST 0x04 26 #define CLK_REF_SEL BIT(7) 27 28 #define QUSB2PHY_PLL_TUNE 0x08 29 #define QUSB2PHY_PLL_USER_CTL1 0x0c 30 #define QUSB2PHY_PLL_USER_CTL2 0x10 31 #define QUSB2PHY_PLL_AUTOPGM_CTL1 0x1c 32 #define QUSB2PHY_PLL_PWR_CTRL 0x18 33 34 /* QUSB2PHY_PLL_STATUS register bits */ 35 #define PLL_LOCKED BIT(5) 36 37 /* QUSB2PHY_PLL_COMMON_STATUS_ONE register bits */ 38 #define CORE_READY_STATUS BIT(0) 39 40 /* QUSB2PHY_PORT_POWERDOWN register bits */ 41 #define CLAMP_N_EN BIT(5) 42 #define FREEZIO_N BIT(1) 43 #define POWER_DOWN BIT(0) 44 45 /* QUSB2PHY_PWR_CTRL1 register bits */ 46 #define PWR_CTRL1_VREF_SUPPLY_TRIM BIT(5) 47 #define PWR_CTRL1_CLAMP_N_EN BIT(1) 48 49 #define QUSB2PHY_REFCLK_ENABLE BIT(0) 50 51 #define PHY_CLK_SCHEME_SEL BIT(0) 52 53 /* QUSB2PHY_INTR_CTRL register bits */ 54 #define DMSE_INTR_HIGH_SEL BIT(4) 55 #define DPSE_INTR_HIGH_SEL BIT(3) 56 #define CHG_DET_INTR_EN BIT(2) 57 #define DMSE_INTR_EN BIT(1) 58 #define DPSE_INTR_EN BIT(0) 59 60 /* QUSB2PHY_PLL_CORE_INPUT_OVERRIDE register bits */ 61 #define CORE_PLL_EN_FROM_RESET BIT(4) 62 #define CORE_RESET BIT(5) 63 #define CORE_RESET_MUX BIT(6) 64 65 /* QUSB2PHY_IMP_CTRL1 register bits */ 66 #define IMP_RES_OFFSET_MASK GENMASK(5, 0) 67 #define IMP_RES_OFFSET_SHIFT 0x0 68 69 /* QUSB2PHY_PLL_BIAS_CONTROL_2 register bits */ 70 #define BIAS_CTRL2_RES_OFFSET_MASK GENMASK(5, 0) 71 #define BIAS_CTRL2_RES_OFFSET_SHIFT 0x0 72 73 /* QUSB2PHY_CHG_CONTROL_2 register bits */ 74 #define CHG_CTRL2_OFFSET_MASK GENMASK(5, 4) 75 #define CHG_CTRL2_OFFSET_SHIFT 0x4 76 77 /* QUSB2PHY_PORT_TUNE1 register bits */ 78 #define HSTX_TRIM_MASK GENMASK(7, 4) 79 #define HSTX_TRIM_SHIFT 0x4 80 #define PREEMPH_WIDTH_HALF_BIT BIT(2) 81 #define PREEMPHASIS_EN_MASK GENMASK(1, 0) 82 #define PREEMPHASIS_EN_SHIFT 0x0 83 84 /* QUSB2PHY_PORT_TUNE2 register bits */ 85 #define HSDISC_TRIM_MASK GENMASK(1, 0) 86 #define HSDISC_TRIM_SHIFT 0x0 87 88 #define QUSB2PHY_PLL_ANALOG_CONTROLS_TWO 0x04 89 #define QUSB2PHY_PLL_CLOCK_INVERTERS 0x18c 90 #define QUSB2PHY_PLL_CMODE 0x2c 91 #define QUSB2PHY_PLL_LOCK_DELAY 0x184 92 #define QUSB2PHY_PLL_DIGITAL_TIMERS_TWO 0xb4 93 #define QUSB2PHY_PLL_BIAS_CONTROL_1 0x194 94 #define QUSB2PHY_PLL_BIAS_CONTROL_2 0x198 95 #define QUSB2PHY_PWR_CTRL2 0x214 96 #define QUSB2PHY_IMP_CTRL1 0x220 97 #define QUSB2PHY_IMP_CTRL2 0x224 98 #define QUSB2PHY_CHG_CTRL2 0x23c 99 100 struct qusb2_phy_init_tbl { 101 unsigned int offset; 102 unsigned int val; 103 /* 104 * register part of layout ? 105 * if yes, then offset gives index in the reg-layout 106 */ 107 int in_layout; 108 }; 109 110 #define QUSB2_PHY_INIT_CFG(o, v) \ 111 { \ 112 .offset = o, \ 113 .val = v, \ 114 } 115 116 #define QUSB2_PHY_INIT_CFG_L(o, v) \ 117 { \ 118 .offset = o, \ 119 .val = v, \ 120 .in_layout = 1, \ 121 } 122 123 /* set of registers with offsets different per-PHY */ 124 enum qusb2phy_reg_layout { 125 QUSB2PHY_PLL_CORE_INPUT_OVERRIDE, 126 QUSB2PHY_PLL_STATUS, 127 QUSB2PHY_PORT_TUNE1, 128 QUSB2PHY_PORT_TUNE2, 129 QUSB2PHY_PORT_TUNE3, 130 QUSB2PHY_PORT_TUNE4, 131 QUSB2PHY_PORT_TUNE5, 132 QUSB2PHY_PORT_TEST1, 133 QUSB2PHY_PORT_TEST2, 134 QUSB2PHY_PORT_POWERDOWN, 135 QUSB2PHY_INTR_CTRL, 136 }; 137 138 static const unsigned int msm8996_regs_layout[] = { 139 [QUSB2PHY_PLL_STATUS] = 0x38, 140 [QUSB2PHY_PORT_TUNE1] = 0x80, 141 [QUSB2PHY_PORT_TUNE2] = 0x84, 142 [QUSB2PHY_PORT_TUNE3] = 0x88, 143 [QUSB2PHY_PORT_TUNE4] = 0x8c, 144 [QUSB2PHY_PORT_TUNE5] = 0x90, 145 [QUSB2PHY_PORT_TEST1] = 0xb8, 146 [QUSB2PHY_PORT_TEST2] = 0x9c, 147 [QUSB2PHY_PORT_POWERDOWN] = 0xb4, 148 [QUSB2PHY_INTR_CTRL] = 0xbc, 149 }; 150 151 static const struct qusb2_phy_init_tbl msm8996_init_tbl[] = { 152 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0xf8), 153 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0xb3), 154 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0x83), 155 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0xc0), 156 157 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_TUNE, 0x30), 158 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL1, 0x79), 159 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL2, 0x21), 160 161 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TEST2, 0x14), 162 163 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_AUTOPGM_CTL1, 0x9f), 164 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_PWR_CTRL, 0x00), 165 }; 166 167 static const unsigned int msm8998_regs_layout[] = { 168 [QUSB2PHY_PLL_CORE_INPUT_OVERRIDE] = 0xa8, 169 [QUSB2PHY_PLL_STATUS] = 0x1a0, 170 [QUSB2PHY_PORT_TUNE1] = 0x23c, 171 [QUSB2PHY_PORT_TUNE2] = 0x240, 172 [QUSB2PHY_PORT_TUNE3] = 0x244, 173 [QUSB2PHY_PORT_TUNE4] = 0x248, 174 [QUSB2PHY_PORT_TEST1] = 0x24c, 175 [QUSB2PHY_PORT_TEST2] = 0x250, 176 [QUSB2PHY_PORT_POWERDOWN] = 0x210, 177 [QUSB2PHY_INTR_CTRL] = 0x22c, 178 }; 179 180 static const struct qusb2_phy_init_tbl msm8998_init_tbl[] = { 181 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_ANALOG_CONTROLS_TWO, 0x13), 182 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CLOCK_INVERTERS, 0x7c), 183 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CMODE, 0x80), 184 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_LOCK_DELAY, 0x0a), 185 186 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0xa5), 187 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0x09), 188 189 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_DIGITAL_TIMERS_TWO, 0x19), 190 }; 191 192 static const unsigned int qusb2_v2_regs_layout[] = { 193 [QUSB2PHY_PLL_CORE_INPUT_OVERRIDE] = 0xa8, 194 [QUSB2PHY_PLL_STATUS] = 0x1a0, 195 [QUSB2PHY_PORT_TUNE1] = 0x240, 196 [QUSB2PHY_PORT_TUNE2] = 0x244, 197 [QUSB2PHY_PORT_TUNE3] = 0x248, 198 [QUSB2PHY_PORT_TUNE4] = 0x24c, 199 [QUSB2PHY_PORT_TUNE5] = 0x250, 200 [QUSB2PHY_PORT_TEST1] = 0x254, 201 [QUSB2PHY_PORT_TEST2] = 0x258, 202 [QUSB2PHY_PORT_POWERDOWN] = 0x210, 203 [QUSB2PHY_INTR_CTRL] = 0x230, 204 }; 205 206 static const struct qusb2_phy_init_tbl qusb2_v2_init_tbl[] = { 207 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_ANALOG_CONTROLS_TWO, 0x03), 208 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CLOCK_INVERTERS, 0x7c), 209 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CMODE, 0x80), 210 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_LOCK_DELAY, 0x0a), 211 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_DIGITAL_TIMERS_TWO, 0x19), 212 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_1, 0x40), 213 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_2, 0x20), 214 QUSB2_PHY_INIT_CFG(QUSB2PHY_PWR_CTRL2, 0x21), 215 QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL1, 0x0), 216 QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL2, 0x58), 217 218 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0x30), 219 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0x29), 220 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0xca), 221 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0x04), 222 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE5, 0x03), 223 224 QUSB2_PHY_INIT_CFG(QUSB2PHY_CHG_CTRL2, 0x0), 225 }; 226 227 struct qusb2_phy_cfg { 228 const struct qusb2_phy_init_tbl *tbl; 229 /* number of entries in the table */ 230 unsigned int tbl_num; 231 /* offset to PHY_CLK_SCHEME register in TCSR map */ 232 unsigned int clk_scheme_offset; 233 234 /* array of registers with different offsets */ 235 const unsigned int *regs; 236 unsigned int mask_core_ready; 237 unsigned int disable_ctrl; 238 unsigned int autoresume_en; 239 240 /* true if PHY has PLL_TEST register to select clk_scheme */ 241 bool has_pll_test; 242 243 /* true if TUNE1 register must be updated by fused value, else TUNE2 */ 244 bool update_tune1_with_efuse; 245 246 /* true if PHY has PLL_CORE_INPUT_OVERRIDE register to reset PLL */ 247 bool has_pll_override; 248 }; 249 250 static const struct qusb2_phy_cfg msm8996_phy_cfg = { 251 .tbl = msm8996_init_tbl, 252 .tbl_num = ARRAY_SIZE(msm8996_init_tbl), 253 .regs = msm8996_regs_layout, 254 255 .has_pll_test = true, 256 .disable_ctrl = (CLAMP_N_EN | FREEZIO_N | POWER_DOWN), 257 .mask_core_ready = PLL_LOCKED, 258 .autoresume_en = BIT(3), 259 }; 260 261 static const struct qusb2_phy_cfg msm8998_phy_cfg = { 262 .tbl = msm8998_init_tbl, 263 .tbl_num = ARRAY_SIZE(msm8998_init_tbl), 264 .regs = msm8998_regs_layout, 265 266 .disable_ctrl = POWER_DOWN, 267 .mask_core_ready = CORE_READY_STATUS, 268 .has_pll_override = true, 269 .autoresume_en = BIT(0), 270 .update_tune1_with_efuse = true, 271 }; 272 273 static const struct qusb2_phy_cfg qusb2_v2_phy_cfg = { 274 .tbl = qusb2_v2_init_tbl, 275 .tbl_num = ARRAY_SIZE(qusb2_v2_init_tbl), 276 .regs = qusb2_v2_regs_layout, 277 278 .disable_ctrl = (PWR_CTRL1_VREF_SUPPLY_TRIM | PWR_CTRL1_CLAMP_N_EN | 279 POWER_DOWN), 280 .mask_core_ready = CORE_READY_STATUS, 281 .has_pll_override = true, 282 .autoresume_en = BIT(0), 283 .update_tune1_with_efuse = true, 284 }; 285 286 static const char * const qusb2_phy_vreg_names[] = { 287 "vdda-pll", "vdda-phy-dpdm", 288 }; 289 290 #define QUSB2_NUM_VREGS ARRAY_SIZE(qusb2_phy_vreg_names) 291 292 /* struct override_param - structure holding qusb2 v2 phy overriding param 293 * set override true if the device tree property exists and read and assign 294 * to value 295 */ 296 struct override_param { 297 bool override; 298 u8 value; 299 }; 300 301 /*struct override_params - structure holding qusb2 v2 phy overriding params 302 * @imp_res_offset: rescode offset to be updated in IMP_CTRL1 register 303 * @hstx_trim: HSTX_TRIM to be updated in TUNE1 register 304 * @preemphasis: Amplitude Pre-Emphasis to be updated in TUNE1 register 305 * @preemphasis_width: half/full-width Pre-Emphasis updated via TUNE1 306 * @bias_ctrl: bias ctrl to be updated in BIAS_CONTROL_2 register 307 * @charge_ctrl: charge ctrl to be updated in CHG_CTRL2 register 308 * @hsdisc_trim: disconnect threshold to be updated in TUNE2 register 309 */ 310 struct override_params { 311 struct override_param imp_res_offset; 312 struct override_param hstx_trim; 313 struct override_param preemphasis; 314 struct override_param preemphasis_width; 315 struct override_param bias_ctrl; 316 struct override_param charge_ctrl; 317 struct override_param hsdisc_trim; 318 }; 319 320 /** 321 * struct qusb2_phy - structure holding qusb2 phy attributes 322 * 323 * @phy: generic phy 324 * @base: iomapped memory space for qubs2 phy 325 * 326 * @cfg_ahb_clk: AHB2PHY interface clock 327 * @ref_clk: phy reference clock 328 * @iface_clk: phy interface clock 329 * @phy_reset: phy reset control 330 * @vregs: regulator supplies bulk data 331 * 332 * @tcsr: TCSR syscon register map 333 * @cell: nvmem cell containing phy tuning value 334 * 335 * @overrides: pointer to structure for all overriding tuning params 336 * 337 * @cfg: phy config data 338 * @has_se_clk_scheme: indicate if PHY has single-ended ref clock scheme 339 * @phy_initialized: indicate if PHY has been initialized 340 * @mode: current PHY mode 341 */ 342 struct qusb2_phy { 343 struct phy *phy; 344 void __iomem *base; 345 346 struct clk *cfg_ahb_clk; 347 struct clk *ref_clk; 348 struct clk *iface_clk; 349 struct reset_control *phy_reset; 350 struct regulator_bulk_data vregs[QUSB2_NUM_VREGS]; 351 352 struct regmap *tcsr; 353 struct nvmem_cell *cell; 354 355 struct override_params overrides; 356 357 const struct qusb2_phy_cfg *cfg; 358 bool has_se_clk_scheme; 359 bool phy_initialized; 360 enum phy_mode mode; 361 }; 362 363 static inline void qusb2_write_mask(void __iomem *base, u32 offset, 364 u32 val, u32 mask) 365 { 366 u32 reg; 367 368 reg = readl(base + offset); 369 reg &= ~mask; 370 reg |= val & mask; 371 writel(reg, base + offset); 372 373 /* Ensure above write is completed */ 374 readl(base + offset); 375 } 376 377 static inline void qusb2_setbits(void __iomem *base, u32 offset, u32 val) 378 { 379 u32 reg; 380 381 reg = readl(base + offset); 382 reg |= val; 383 writel(reg, base + offset); 384 385 /* Ensure above write is completed */ 386 readl(base + offset); 387 } 388 389 static inline void qusb2_clrbits(void __iomem *base, u32 offset, u32 val) 390 { 391 u32 reg; 392 393 reg = readl(base + offset); 394 reg &= ~val; 395 writel(reg, base + offset); 396 397 /* Ensure above write is completed */ 398 readl(base + offset); 399 } 400 401 static inline 402 void qcom_qusb2_phy_configure(void __iomem *base, 403 const unsigned int *regs, 404 const struct qusb2_phy_init_tbl tbl[], int num) 405 { 406 int i; 407 408 for (i = 0; i < num; i++) { 409 if (tbl[i].in_layout) 410 writel(tbl[i].val, base + regs[tbl[i].offset]); 411 else 412 writel(tbl[i].val, base + tbl[i].offset); 413 } 414 } 415 416 /* 417 * Update board specific PHY tuning override values if specified from 418 * device tree. 419 */ 420 static void qusb2_phy_override_phy_params(struct qusb2_phy *qphy) 421 { 422 const struct qusb2_phy_cfg *cfg = qphy->cfg; 423 struct override_params *or = &qphy->overrides; 424 425 if (or->imp_res_offset.override) 426 qusb2_write_mask(qphy->base, QUSB2PHY_IMP_CTRL1, 427 or->imp_res_offset.value << IMP_RES_OFFSET_SHIFT, 428 IMP_RES_OFFSET_MASK); 429 430 if (or->bias_ctrl.override) 431 qusb2_write_mask(qphy->base, QUSB2PHY_PLL_BIAS_CONTROL_2, 432 or->bias_ctrl.value << BIAS_CTRL2_RES_OFFSET_SHIFT, 433 BIAS_CTRL2_RES_OFFSET_MASK); 434 435 if (or->charge_ctrl.override) 436 qusb2_write_mask(qphy->base, QUSB2PHY_CHG_CTRL2, 437 or->charge_ctrl.value << CHG_CTRL2_OFFSET_SHIFT, 438 CHG_CTRL2_OFFSET_MASK); 439 440 if (or->hstx_trim.override) 441 qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1], 442 or->hstx_trim.value << HSTX_TRIM_SHIFT, 443 HSTX_TRIM_MASK); 444 445 if (or->preemphasis.override) 446 qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1], 447 or->preemphasis.value << PREEMPHASIS_EN_SHIFT, 448 PREEMPHASIS_EN_MASK); 449 450 if (or->preemphasis_width.override) { 451 if (or->preemphasis_width.value == 452 QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT) 453 qusb2_setbits(qphy->base, 454 cfg->regs[QUSB2PHY_PORT_TUNE1], 455 PREEMPH_WIDTH_HALF_BIT); 456 else 457 qusb2_clrbits(qphy->base, 458 cfg->regs[QUSB2PHY_PORT_TUNE1], 459 PREEMPH_WIDTH_HALF_BIT); 460 } 461 462 if (or->hsdisc_trim.override) 463 qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE2], 464 or->hsdisc_trim.value << HSDISC_TRIM_SHIFT, 465 HSDISC_TRIM_MASK); 466 } 467 468 /* 469 * Fetches HS Tx tuning value from nvmem and sets the 470 * QUSB2PHY_PORT_TUNE1/2 register. 471 * For error case, skip setting the value and use the default value. 472 */ 473 static void qusb2_phy_set_tune2_param(struct qusb2_phy *qphy) 474 { 475 struct device *dev = &qphy->phy->dev; 476 const struct qusb2_phy_cfg *cfg = qphy->cfg; 477 u8 *val; 478 479 /* efuse register is optional */ 480 if (!qphy->cell) 481 return; 482 483 /* 484 * Read efuse register having TUNE2/1 parameter's high nibble. 485 * If efuse register shows value as 0x0 (indicating value is not 486 * fused), or if we fail to find a valid efuse register setting, 487 * then use default value for high nibble that we have already 488 * set while configuring the phy. 489 */ 490 val = nvmem_cell_read(qphy->cell, NULL); 491 if (IS_ERR(val) || !val[0]) { 492 dev_dbg(dev, "failed to read a valid hs-tx trim value\n"); 493 return; 494 } 495 496 /* Fused TUNE1/2 value is the higher nibble only */ 497 if (cfg->update_tune1_with_efuse) 498 qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1], 499 val[0] << HSTX_TRIM_SHIFT, 500 HSTX_TRIM_MASK); 501 else 502 qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE2], 503 val[0] << HSTX_TRIM_SHIFT, 504 HSTX_TRIM_MASK); 505 } 506 507 static int qusb2_phy_set_mode(struct phy *phy, 508 enum phy_mode mode, int submode) 509 { 510 struct qusb2_phy *qphy = phy_get_drvdata(phy); 511 512 qphy->mode = mode; 513 514 return 0; 515 } 516 517 static int __maybe_unused qusb2_phy_runtime_suspend(struct device *dev) 518 { 519 struct qusb2_phy *qphy = dev_get_drvdata(dev); 520 const struct qusb2_phy_cfg *cfg = qphy->cfg; 521 u32 intr_mask; 522 523 dev_vdbg(dev, "Suspending QUSB2 Phy, mode:%d\n", qphy->mode); 524 525 if (!qphy->phy_initialized) { 526 dev_vdbg(dev, "PHY not initialized, bailing out\n"); 527 return 0; 528 } 529 530 /* 531 * Enable DP/DM interrupts to detect line state changes based on current 532 * speed. In other words, enable the triggers _opposite_ of what the 533 * current D+/D- levels are e.g. if currently D+ high, D- low 534 * (HS 'J'/Suspend), configure the mask to trigger on D+ low OR D- high 535 */ 536 intr_mask = DPSE_INTR_EN | DMSE_INTR_EN; 537 switch (qphy->mode) { 538 case PHY_MODE_USB_HOST_HS: 539 case PHY_MODE_USB_HOST_FS: 540 case PHY_MODE_USB_DEVICE_HS: 541 case PHY_MODE_USB_DEVICE_FS: 542 intr_mask |= DMSE_INTR_HIGH_SEL; 543 break; 544 case PHY_MODE_USB_HOST_LS: 545 case PHY_MODE_USB_DEVICE_LS: 546 intr_mask |= DPSE_INTR_HIGH_SEL; 547 break; 548 default: 549 /* No device connected, enable both DP/DM high interrupt */ 550 intr_mask |= DMSE_INTR_HIGH_SEL; 551 intr_mask |= DPSE_INTR_HIGH_SEL; 552 break; 553 } 554 555 writel(intr_mask, qphy->base + cfg->regs[QUSB2PHY_INTR_CTRL]); 556 557 /* hold core PLL into reset */ 558 if (cfg->has_pll_override) { 559 qusb2_setbits(qphy->base, 560 cfg->regs[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE], 561 CORE_PLL_EN_FROM_RESET | CORE_RESET | 562 CORE_RESET_MUX); 563 } 564 565 /* enable phy auto-resume only if device is connected on bus */ 566 if (qphy->mode != PHY_MODE_INVALID) { 567 qusb2_setbits(qphy->base, cfg->regs[QUSB2PHY_PORT_TEST1], 568 cfg->autoresume_en); 569 /* Autoresume bit has to be toggled in order to enable it */ 570 qusb2_clrbits(qphy->base, cfg->regs[QUSB2PHY_PORT_TEST1], 571 cfg->autoresume_en); 572 } 573 574 if (!qphy->has_se_clk_scheme) 575 clk_disable_unprepare(qphy->ref_clk); 576 577 clk_disable_unprepare(qphy->cfg_ahb_clk); 578 clk_disable_unprepare(qphy->iface_clk); 579 580 return 0; 581 } 582 583 static int __maybe_unused qusb2_phy_runtime_resume(struct device *dev) 584 { 585 struct qusb2_phy *qphy = dev_get_drvdata(dev); 586 const struct qusb2_phy_cfg *cfg = qphy->cfg; 587 int ret; 588 589 dev_vdbg(dev, "Resuming QUSB2 phy, mode:%d\n", qphy->mode); 590 591 if (!qphy->phy_initialized) { 592 dev_vdbg(dev, "PHY not initialized, bailing out\n"); 593 return 0; 594 } 595 596 ret = clk_prepare_enable(qphy->iface_clk); 597 if (ret) { 598 dev_err(dev, "failed to enable iface_clk, %d\n", ret); 599 return ret; 600 } 601 602 ret = clk_prepare_enable(qphy->cfg_ahb_clk); 603 if (ret) { 604 dev_err(dev, "failed to enable cfg ahb clock, %d\n", ret); 605 goto disable_iface_clk; 606 } 607 608 if (!qphy->has_se_clk_scheme) { 609 ret = clk_prepare_enable(qphy->ref_clk); 610 if (ret) { 611 dev_err(dev, "failed to enable ref clk, %d\n", ret); 612 goto disable_ahb_clk; 613 } 614 } 615 616 writel(0x0, qphy->base + cfg->regs[QUSB2PHY_INTR_CTRL]); 617 618 /* bring core PLL out of reset */ 619 if (cfg->has_pll_override) { 620 qusb2_clrbits(qphy->base, 621 cfg->regs[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE], 622 CORE_RESET | CORE_RESET_MUX); 623 } 624 625 return 0; 626 627 disable_ahb_clk: 628 clk_disable_unprepare(qphy->cfg_ahb_clk); 629 disable_iface_clk: 630 clk_disable_unprepare(qphy->iface_clk); 631 632 return ret; 633 } 634 635 static int qusb2_phy_init(struct phy *phy) 636 { 637 struct qusb2_phy *qphy = phy_get_drvdata(phy); 638 const struct qusb2_phy_cfg *cfg = qphy->cfg; 639 unsigned int val = 0; 640 unsigned int clk_scheme; 641 int ret; 642 643 dev_vdbg(&phy->dev, "%s(): Initializing QUSB2 phy\n", __func__); 644 645 /* turn on regulator supplies */ 646 ret = regulator_bulk_enable(ARRAY_SIZE(qphy->vregs), qphy->vregs); 647 if (ret) 648 return ret; 649 650 ret = clk_prepare_enable(qphy->iface_clk); 651 if (ret) { 652 dev_err(&phy->dev, "failed to enable iface_clk, %d\n", ret); 653 goto poweroff_phy; 654 } 655 656 /* enable ahb interface clock to program phy */ 657 ret = clk_prepare_enable(qphy->cfg_ahb_clk); 658 if (ret) { 659 dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret); 660 goto disable_iface_clk; 661 } 662 663 /* Perform phy reset */ 664 ret = reset_control_assert(qphy->phy_reset); 665 if (ret) { 666 dev_err(&phy->dev, "failed to assert phy_reset, %d\n", ret); 667 goto disable_ahb_clk; 668 } 669 670 /* 100 us delay to keep PHY in reset mode */ 671 usleep_range(100, 150); 672 673 ret = reset_control_deassert(qphy->phy_reset); 674 if (ret) { 675 dev_err(&phy->dev, "failed to de-assert phy_reset, %d\n", ret); 676 goto disable_ahb_clk; 677 } 678 679 /* Disable the PHY */ 680 qusb2_setbits(qphy->base, cfg->regs[QUSB2PHY_PORT_POWERDOWN], 681 qphy->cfg->disable_ctrl); 682 683 if (cfg->has_pll_test) { 684 /* save reset value to override reference clock scheme later */ 685 val = readl(qphy->base + QUSB2PHY_PLL_TEST); 686 } 687 688 qcom_qusb2_phy_configure(qphy->base, cfg->regs, cfg->tbl, 689 cfg->tbl_num); 690 691 /* Override board specific PHY tuning values */ 692 qusb2_phy_override_phy_params(qphy); 693 694 /* Set efuse value for tuning the PHY */ 695 qusb2_phy_set_tune2_param(qphy); 696 697 /* Enable the PHY */ 698 qusb2_clrbits(qphy->base, cfg->regs[QUSB2PHY_PORT_POWERDOWN], 699 POWER_DOWN); 700 701 /* Required to get phy pll lock successfully */ 702 usleep_range(150, 160); 703 704 /* Default is single-ended clock on msm8996 */ 705 qphy->has_se_clk_scheme = true; 706 /* 707 * read TCSR_PHY_CLK_SCHEME register to check if single-ended 708 * clock scheme is selected. If yes, then disable differential 709 * ref_clk and use single-ended clock, otherwise use differential 710 * ref_clk only. 711 */ 712 if (qphy->tcsr) { 713 ret = regmap_read(qphy->tcsr, qphy->cfg->clk_scheme_offset, 714 &clk_scheme); 715 if (ret) { 716 dev_err(&phy->dev, "failed to read clk scheme reg\n"); 717 goto assert_phy_reset; 718 } 719 720 /* is it a differential clock scheme ? */ 721 if (!(clk_scheme & PHY_CLK_SCHEME_SEL)) { 722 dev_vdbg(&phy->dev, "%s(): select differential clk\n", 723 __func__); 724 qphy->has_se_clk_scheme = false; 725 } else { 726 dev_vdbg(&phy->dev, "%s(): select single-ended clk\n", 727 __func__); 728 } 729 } 730 731 if (!qphy->has_se_clk_scheme) { 732 ret = clk_prepare_enable(qphy->ref_clk); 733 if (ret) { 734 dev_err(&phy->dev, "failed to enable ref clk, %d\n", 735 ret); 736 goto assert_phy_reset; 737 } 738 } 739 740 if (cfg->has_pll_test) { 741 if (!qphy->has_se_clk_scheme) 742 val &= ~CLK_REF_SEL; 743 else 744 val |= CLK_REF_SEL; 745 746 writel(val, qphy->base + QUSB2PHY_PLL_TEST); 747 748 /* ensure above write is through */ 749 readl(qphy->base + QUSB2PHY_PLL_TEST); 750 } 751 752 /* Required to get phy pll lock successfully */ 753 usleep_range(100, 110); 754 755 val = readb(qphy->base + cfg->regs[QUSB2PHY_PLL_STATUS]); 756 if (!(val & cfg->mask_core_ready)) { 757 dev_err(&phy->dev, 758 "QUSB2PHY pll lock failed: status reg = %x\n", val); 759 ret = -EBUSY; 760 goto disable_ref_clk; 761 } 762 qphy->phy_initialized = true; 763 764 return 0; 765 766 disable_ref_clk: 767 if (!qphy->has_se_clk_scheme) 768 clk_disable_unprepare(qphy->ref_clk); 769 assert_phy_reset: 770 reset_control_assert(qphy->phy_reset); 771 disable_ahb_clk: 772 clk_disable_unprepare(qphy->cfg_ahb_clk); 773 disable_iface_clk: 774 clk_disable_unprepare(qphy->iface_clk); 775 poweroff_phy: 776 regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs); 777 778 return ret; 779 } 780 781 static int qusb2_phy_exit(struct phy *phy) 782 { 783 struct qusb2_phy *qphy = phy_get_drvdata(phy); 784 785 /* Disable the PHY */ 786 qusb2_setbits(qphy->base, qphy->cfg->regs[QUSB2PHY_PORT_POWERDOWN], 787 qphy->cfg->disable_ctrl); 788 789 if (!qphy->has_se_clk_scheme) 790 clk_disable_unprepare(qphy->ref_clk); 791 792 reset_control_assert(qphy->phy_reset); 793 794 clk_disable_unprepare(qphy->cfg_ahb_clk); 795 clk_disable_unprepare(qphy->iface_clk); 796 797 regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs); 798 799 qphy->phy_initialized = false; 800 801 return 0; 802 } 803 804 static const struct phy_ops qusb2_phy_gen_ops = { 805 .init = qusb2_phy_init, 806 .exit = qusb2_phy_exit, 807 .set_mode = qusb2_phy_set_mode, 808 .owner = THIS_MODULE, 809 }; 810 811 static const struct of_device_id qusb2_phy_of_match_table[] = { 812 { 813 .compatible = "qcom,ipq8074-qusb2-phy", 814 .data = &msm8996_phy_cfg, 815 }, { 816 .compatible = "qcom,msm8996-qusb2-phy", 817 .data = &msm8996_phy_cfg, 818 }, { 819 .compatible = "qcom,msm8998-qusb2-phy", 820 .data = &msm8998_phy_cfg, 821 }, { 822 /* 823 * Deprecated. Only here to support legacy device 824 * trees that didn't include "qcom,qusb2-v2-phy" 825 */ 826 .compatible = "qcom,sdm845-qusb2-phy", 827 .data = &qusb2_v2_phy_cfg, 828 }, { 829 .compatible = "qcom,qusb2-v2-phy", 830 .data = &qusb2_v2_phy_cfg, 831 }, 832 { }, 833 }; 834 MODULE_DEVICE_TABLE(of, qusb2_phy_of_match_table); 835 836 static const struct dev_pm_ops qusb2_phy_pm_ops = { 837 SET_RUNTIME_PM_OPS(qusb2_phy_runtime_suspend, 838 qusb2_phy_runtime_resume, NULL) 839 }; 840 841 static int qusb2_phy_probe(struct platform_device *pdev) 842 { 843 struct device *dev = &pdev->dev; 844 struct qusb2_phy *qphy; 845 struct phy_provider *phy_provider; 846 struct phy *generic_phy; 847 int ret, i; 848 int num; 849 u32 value; 850 struct override_params *or; 851 852 qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL); 853 if (!qphy) 854 return -ENOMEM; 855 or = &qphy->overrides; 856 857 qphy->base = devm_platform_ioremap_resource(pdev, 0); 858 if (IS_ERR(qphy->base)) 859 return PTR_ERR(qphy->base); 860 861 qphy->cfg_ahb_clk = devm_clk_get(dev, "cfg_ahb"); 862 if (IS_ERR(qphy->cfg_ahb_clk)) { 863 ret = PTR_ERR(qphy->cfg_ahb_clk); 864 if (ret != -EPROBE_DEFER) 865 dev_err(dev, "failed to get cfg ahb clk, %d\n", ret); 866 return ret; 867 } 868 869 qphy->ref_clk = devm_clk_get(dev, "ref"); 870 if (IS_ERR(qphy->ref_clk)) { 871 ret = PTR_ERR(qphy->ref_clk); 872 if (ret != -EPROBE_DEFER) 873 dev_err(dev, "failed to get ref clk, %d\n", ret); 874 return ret; 875 } 876 877 qphy->iface_clk = devm_clk_get_optional(dev, "iface"); 878 if (IS_ERR(qphy->iface_clk)) 879 return PTR_ERR(qphy->iface_clk); 880 881 qphy->phy_reset = devm_reset_control_get_by_index(&pdev->dev, 0); 882 if (IS_ERR(qphy->phy_reset)) { 883 dev_err(dev, "failed to get phy core reset\n"); 884 return PTR_ERR(qphy->phy_reset); 885 } 886 887 num = ARRAY_SIZE(qphy->vregs); 888 for (i = 0; i < num; i++) 889 qphy->vregs[i].supply = qusb2_phy_vreg_names[i]; 890 891 ret = devm_regulator_bulk_get(dev, num, qphy->vregs); 892 if (ret) { 893 if (ret != -EPROBE_DEFER) 894 dev_err(dev, "failed to get regulator supplies: %d\n", 895 ret); 896 return ret; 897 } 898 899 /* Get the specific init parameters of QMP phy */ 900 qphy->cfg = of_device_get_match_data(dev); 901 902 qphy->tcsr = syscon_regmap_lookup_by_phandle(dev->of_node, 903 "qcom,tcsr-syscon"); 904 if (IS_ERR(qphy->tcsr)) { 905 dev_dbg(dev, "failed to lookup TCSR regmap\n"); 906 qphy->tcsr = NULL; 907 } 908 909 qphy->cell = devm_nvmem_cell_get(dev, NULL); 910 if (IS_ERR(qphy->cell)) { 911 if (PTR_ERR(qphy->cell) == -EPROBE_DEFER) 912 return -EPROBE_DEFER; 913 qphy->cell = NULL; 914 dev_dbg(dev, "failed to lookup tune2 hstx trim value\n"); 915 } 916 917 if (!of_property_read_u32(dev->of_node, "qcom,imp-res-offset-value", 918 &value)) { 919 or->imp_res_offset.value = (u8)value; 920 or->imp_res_offset.override = true; 921 } 922 923 if (!of_property_read_u32(dev->of_node, "qcom,bias-ctrl-value", 924 &value)) { 925 or->bias_ctrl.value = (u8)value; 926 or->bias_ctrl.override = true; 927 } 928 929 if (!of_property_read_u32(dev->of_node, "qcom,charge-ctrl-value", 930 &value)) { 931 or->charge_ctrl.value = (u8)value; 932 or->charge_ctrl.override = true; 933 } 934 935 if (!of_property_read_u32(dev->of_node, "qcom,hstx-trim-value", 936 &value)) { 937 or->hstx_trim.value = (u8)value; 938 or->hstx_trim.override = true; 939 } 940 941 if (!of_property_read_u32(dev->of_node, "qcom,preemphasis-level", 942 &value)) { 943 or->preemphasis.value = (u8)value; 944 or->preemphasis.override = true; 945 } 946 947 if (!of_property_read_u32(dev->of_node, "qcom,preemphasis-width", 948 &value)) { 949 or->preemphasis_width.value = (u8)value; 950 or->preemphasis_width.override = true; 951 } 952 953 if (!of_property_read_u32(dev->of_node, "qcom,hsdisc-trim-value", 954 &value)) { 955 or->hsdisc_trim.value = (u8)value; 956 or->hsdisc_trim.override = true; 957 } 958 959 pm_runtime_set_active(dev); 960 pm_runtime_enable(dev); 961 /* 962 * Prevent runtime pm from being ON by default. Users can enable 963 * it using power/control in sysfs. 964 */ 965 pm_runtime_forbid(dev); 966 967 generic_phy = devm_phy_create(dev, NULL, &qusb2_phy_gen_ops); 968 if (IS_ERR(generic_phy)) { 969 ret = PTR_ERR(generic_phy); 970 dev_err(dev, "failed to create phy, %d\n", ret); 971 pm_runtime_disable(dev); 972 return ret; 973 } 974 qphy->phy = generic_phy; 975 976 dev_set_drvdata(dev, qphy); 977 phy_set_drvdata(generic_phy, qphy); 978 979 phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); 980 if (!IS_ERR(phy_provider)) 981 dev_info(dev, "Registered Qcom-QUSB2 phy\n"); 982 else 983 pm_runtime_disable(dev); 984 985 return PTR_ERR_OR_ZERO(phy_provider); 986 } 987 988 static struct platform_driver qusb2_phy_driver = { 989 .probe = qusb2_phy_probe, 990 .driver = { 991 .name = "qcom-qusb2-phy", 992 .pm = &qusb2_phy_pm_ops, 993 .of_match_table = qusb2_phy_of_match_table, 994 }, 995 }; 996 997 module_platform_driver(qusb2_phy_driver); 998 999 MODULE_AUTHOR("Vivek Gautam <vivek.gautam@codeaurora.org>"); 1000 MODULE_DESCRIPTION("Qualcomm QUSB2 PHY driver"); 1001 MODULE_LICENSE("GPL v2"); 1002