1 // SPDX-License-Identifier: GPL-2.0 2 /* 3 * Copyright (c) 2017, 2019, The Linux Foundation. All rights reserved. 4 */ 5 6 #include <linux/clk.h> 7 #include <linux/delay.h> 8 #include <linux/err.h> 9 #include <linux/io.h> 10 #include <linux/kernel.h> 11 #include <linux/mfd/syscon.h> 12 #include <linux/module.h> 13 #include <linux/nvmem-consumer.h> 14 #include <linux/of.h> 15 #include <linux/of_device.h> 16 #include <linux/phy/phy.h> 17 #include <linux/platform_device.h> 18 #include <linux/regmap.h> 19 #include <linux/regulator/consumer.h> 20 #include <linux/reset.h> 21 #include <linux/slab.h> 22 23 #include <dt-bindings/phy/phy-qcom-qusb2.h> 24 25 #define QUSB2PHY_PLL 0x0 26 #define QUSB2PHY_PLL_TEST 0x04 27 #define CLK_REF_SEL BIT(7) 28 29 #define QUSB2PHY_PLL_TUNE 0x08 30 #define QUSB2PHY_PLL_USER_CTL1 0x0c 31 #define QUSB2PHY_PLL_USER_CTL2 0x10 32 #define QUSB2PHY_PLL_AUTOPGM_CTL1 0x1c 33 #define QUSB2PHY_PLL_PWR_CTRL 0x18 34 35 /* QUSB2PHY_PLL_STATUS register bits */ 36 #define PLL_LOCKED BIT(5) 37 38 /* QUSB2PHY_PLL_COMMON_STATUS_ONE register bits */ 39 #define CORE_READY_STATUS BIT(0) 40 41 /* QUSB2PHY_PORT_POWERDOWN register bits */ 42 #define CLAMP_N_EN BIT(5) 43 #define FREEZIO_N BIT(1) 44 #define POWER_DOWN BIT(0) 45 46 /* QUSB2PHY_PWR_CTRL1 register bits */ 47 #define PWR_CTRL1_VREF_SUPPLY_TRIM BIT(5) 48 #define PWR_CTRL1_CLAMP_N_EN BIT(1) 49 50 #define QUSB2PHY_REFCLK_ENABLE BIT(0) 51 52 #define PHY_CLK_SCHEME_SEL BIT(0) 53 54 /* QUSB2PHY_INTR_CTRL register bits */ 55 #define DMSE_INTR_HIGH_SEL BIT(4) 56 #define DPSE_INTR_HIGH_SEL BIT(3) 57 #define CHG_DET_INTR_EN BIT(2) 58 #define DMSE_INTR_EN BIT(1) 59 #define DPSE_INTR_EN BIT(0) 60 61 /* QUSB2PHY_PLL_CORE_INPUT_OVERRIDE register bits */ 62 #define CORE_PLL_EN_FROM_RESET BIT(4) 63 #define CORE_RESET BIT(5) 64 #define CORE_RESET_MUX BIT(6) 65 66 /* QUSB2PHY_IMP_CTRL1 register bits */ 67 #define IMP_RES_OFFSET_MASK GENMASK(5, 0) 68 #define IMP_RES_OFFSET_SHIFT 0x0 69 70 /* QUSB2PHY_PLL_BIAS_CONTROL_2 register bits */ 71 #define BIAS_CTRL2_RES_OFFSET_MASK GENMASK(5, 0) 72 #define BIAS_CTRL2_RES_OFFSET_SHIFT 0x0 73 74 /* QUSB2PHY_CHG_CONTROL_2 register bits */ 75 #define CHG_CTRL2_OFFSET_MASK GENMASK(5, 4) 76 #define CHG_CTRL2_OFFSET_SHIFT 0x4 77 78 /* QUSB2PHY_PORT_TUNE1 register bits */ 79 #define HSTX_TRIM_MASK GENMASK(7, 4) 80 #define HSTX_TRIM_SHIFT 0x4 81 #define PREEMPH_WIDTH_HALF_BIT BIT(2) 82 #define PREEMPHASIS_EN_MASK GENMASK(1, 0) 83 #define PREEMPHASIS_EN_SHIFT 0x0 84 85 /* QUSB2PHY_PORT_TUNE2 register bits */ 86 #define HSDISC_TRIM_MASK GENMASK(1, 0) 87 #define HSDISC_TRIM_SHIFT 0x0 88 89 #define QUSB2PHY_PLL_ANALOG_CONTROLS_TWO 0x04 90 #define QUSB2PHY_PLL_CLOCK_INVERTERS 0x18c 91 #define QUSB2PHY_PLL_CMODE 0x2c 92 #define QUSB2PHY_PLL_LOCK_DELAY 0x184 93 #define QUSB2PHY_PLL_DIGITAL_TIMERS_TWO 0xb4 94 #define QUSB2PHY_PLL_BIAS_CONTROL_1 0x194 95 #define QUSB2PHY_PLL_BIAS_CONTROL_2 0x198 96 #define QUSB2PHY_PWR_CTRL2 0x214 97 #define QUSB2PHY_IMP_CTRL1 0x220 98 #define QUSB2PHY_IMP_CTRL2 0x224 99 #define QUSB2PHY_CHG_CTRL2 0x23c 100 101 struct qusb2_phy_init_tbl { 102 unsigned int offset; 103 unsigned int val; 104 /* 105 * register part of layout ? 106 * if yes, then offset gives index in the reg-layout 107 */ 108 int in_layout; 109 }; 110 111 #define QUSB2_PHY_INIT_CFG(o, v) \ 112 { \ 113 .offset = o, \ 114 .val = v, \ 115 } 116 117 #define QUSB2_PHY_INIT_CFG_L(o, v) \ 118 { \ 119 .offset = o, \ 120 .val = v, \ 121 .in_layout = 1, \ 122 } 123 124 /* set of registers with offsets different per-PHY */ 125 enum qusb2phy_reg_layout { 126 QUSB2PHY_PLL_CORE_INPUT_OVERRIDE, 127 QUSB2PHY_PLL_STATUS, 128 QUSB2PHY_PORT_TUNE1, 129 QUSB2PHY_PORT_TUNE2, 130 QUSB2PHY_PORT_TUNE3, 131 QUSB2PHY_PORT_TUNE4, 132 QUSB2PHY_PORT_TUNE5, 133 QUSB2PHY_PORT_TEST1, 134 QUSB2PHY_PORT_TEST2, 135 QUSB2PHY_PORT_POWERDOWN, 136 QUSB2PHY_INTR_CTRL, 137 }; 138 139 static const struct qusb2_phy_init_tbl ipq6018_init_tbl[] = { 140 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL, 0x14), 141 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0xF8), 142 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0xB3), 143 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0x83), 144 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0xC0), 145 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_TUNE, 0x30), 146 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL1, 0x79), 147 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL2, 0x21), 148 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE5, 0x00), 149 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_PWR_CTRL, 0x00), 150 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TEST2, 0x14), 151 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_TEST, 0x80), 152 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_AUTOPGM_CTL1, 0x9F), 153 }; 154 155 static const unsigned int ipq6018_regs_layout[] = { 156 [QUSB2PHY_PLL_STATUS] = 0x38, 157 [QUSB2PHY_PORT_TUNE1] = 0x80, 158 [QUSB2PHY_PORT_TUNE2] = 0x84, 159 [QUSB2PHY_PORT_TUNE3] = 0x88, 160 [QUSB2PHY_PORT_TUNE4] = 0x8C, 161 [QUSB2PHY_PORT_TUNE5] = 0x90, 162 [QUSB2PHY_PORT_TEST1] = 0x98, 163 [QUSB2PHY_PORT_TEST2] = 0x9C, 164 [QUSB2PHY_PORT_POWERDOWN] = 0xB4, 165 [QUSB2PHY_INTR_CTRL] = 0xBC, 166 }; 167 168 static const unsigned int msm8996_regs_layout[] = { 169 [QUSB2PHY_PLL_STATUS] = 0x38, 170 [QUSB2PHY_PORT_TUNE1] = 0x80, 171 [QUSB2PHY_PORT_TUNE2] = 0x84, 172 [QUSB2PHY_PORT_TUNE3] = 0x88, 173 [QUSB2PHY_PORT_TUNE4] = 0x8c, 174 [QUSB2PHY_PORT_TUNE5] = 0x90, 175 [QUSB2PHY_PORT_TEST1] = 0xb8, 176 [QUSB2PHY_PORT_TEST2] = 0x9c, 177 [QUSB2PHY_PORT_POWERDOWN] = 0xb4, 178 [QUSB2PHY_INTR_CTRL] = 0xbc, 179 }; 180 181 static const struct qusb2_phy_init_tbl msm8996_init_tbl[] = { 182 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0xf8), 183 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0xb3), 184 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0x83), 185 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0xc0), 186 187 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_TUNE, 0x30), 188 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL1, 0x79), 189 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL2, 0x21), 190 191 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TEST2, 0x14), 192 193 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_AUTOPGM_CTL1, 0x9f), 194 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_PWR_CTRL, 0x00), 195 }; 196 197 static const unsigned int msm8998_regs_layout[] = { 198 [QUSB2PHY_PLL_CORE_INPUT_OVERRIDE] = 0xa8, 199 [QUSB2PHY_PLL_STATUS] = 0x1a0, 200 [QUSB2PHY_PORT_TUNE1] = 0x23c, 201 [QUSB2PHY_PORT_TUNE2] = 0x240, 202 [QUSB2PHY_PORT_TUNE3] = 0x244, 203 [QUSB2PHY_PORT_TUNE4] = 0x248, 204 [QUSB2PHY_PORT_TEST1] = 0x24c, 205 [QUSB2PHY_PORT_TEST2] = 0x250, 206 [QUSB2PHY_PORT_POWERDOWN] = 0x210, 207 [QUSB2PHY_INTR_CTRL] = 0x22c, 208 }; 209 210 static const struct qusb2_phy_init_tbl msm8998_init_tbl[] = { 211 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_ANALOG_CONTROLS_TWO, 0x13), 212 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CLOCK_INVERTERS, 0x7c), 213 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CMODE, 0x80), 214 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_LOCK_DELAY, 0x0a), 215 216 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0xa5), 217 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0x09), 218 219 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_DIGITAL_TIMERS_TWO, 0x19), 220 }; 221 222 static const struct qusb2_phy_init_tbl sm6115_init_tbl[] = { 223 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0xf8), 224 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0x53), 225 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0x81), 226 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0x17), 227 228 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_TUNE, 0x30), 229 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL1, 0x79), 230 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL2, 0x21), 231 232 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TEST2, 0x14), 233 234 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_AUTOPGM_CTL1, 0x9f), 235 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_PWR_CTRL, 0x00), 236 }; 237 238 static const unsigned int qusb2_v2_regs_layout[] = { 239 [QUSB2PHY_PLL_CORE_INPUT_OVERRIDE] = 0xa8, 240 [QUSB2PHY_PLL_STATUS] = 0x1a0, 241 [QUSB2PHY_PORT_TUNE1] = 0x240, 242 [QUSB2PHY_PORT_TUNE2] = 0x244, 243 [QUSB2PHY_PORT_TUNE3] = 0x248, 244 [QUSB2PHY_PORT_TUNE4] = 0x24c, 245 [QUSB2PHY_PORT_TUNE5] = 0x250, 246 [QUSB2PHY_PORT_TEST1] = 0x254, 247 [QUSB2PHY_PORT_TEST2] = 0x258, 248 [QUSB2PHY_PORT_POWERDOWN] = 0x210, 249 [QUSB2PHY_INTR_CTRL] = 0x230, 250 }; 251 252 static const struct qusb2_phy_init_tbl qusb2_v2_init_tbl[] = { 253 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_ANALOG_CONTROLS_TWO, 0x03), 254 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CLOCK_INVERTERS, 0x7c), 255 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CMODE, 0x80), 256 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_LOCK_DELAY, 0x0a), 257 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_DIGITAL_TIMERS_TWO, 0x19), 258 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_1, 0x40), 259 QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_2, 0x20), 260 QUSB2_PHY_INIT_CFG(QUSB2PHY_PWR_CTRL2, 0x21), 261 QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL1, 0x0), 262 QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL2, 0x58), 263 264 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0x30), 265 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0x29), 266 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0xca), 267 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0x04), 268 QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE5, 0x03), 269 270 QUSB2_PHY_INIT_CFG(QUSB2PHY_CHG_CTRL2, 0x0), 271 }; 272 273 struct qusb2_phy_cfg { 274 const struct qusb2_phy_init_tbl *tbl; 275 /* number of entries in the table */ 276 unsigned int tbl_num; 277 /* offset to PHY_CLK_SCHEME register in TCSR map */ 278 unsigned int clk_scheme_offset; 279 280 /* array of registers with different offsets */ 281 const unsigned int *regs; 282 unsigned int mask_core_ready; 283 unsigned int disable_ctrl; 284 unsigned int autoresume_en; 285 286 /* true if PHY has PLL_TEST register to select clk_scheme */ 287 bool has_pll_test; 288 289 /* true if TUNE1 register must be updated by fused value, else TUNE2 */ 290 bool update_tune1_with_efuse; 291 292 /* true if PHY has PLL_CORE_INPUT_OVERRIDE register to reset PLL */ 293 bool has_pll_override; 294 295 /* true if PHY default clk scheme is single-ended */ 296 bool se_clk_scheme_default; 297 }; 298 299 static const struct qusb2_phy_cfg msm8996_phy_cfg = { 300 .tbl = msm8996_init_tbl, 301 .tbl_num = ARRAY_SIZE(msm8996_init_tbl), 302 .regs = msm8996_regs_layout, 303 304 .has_pll_test = true, 305 .se_clk_scheme_default = true, 306 .disable_ctrl = (CLAMP_N_EN | FREEZIO_N | POWER_DOWN), 307 .mask_core_ready = PLL_LOCKED, 308 .autoresume_en = BIT(3), 309 }; 310 311 static const struct qusb2_phy_cfg msm8998_phy_cfg = { 312 .tbl = msm8998_init_tbl, 313 .tbl_num = ARRAY_SIZE(msm8998_init_tbl), 314 .regs = msm8998_regs_layout, 315 316 .disable_ctrl = POWER_DOWN, 317 .mask_core_ready = CORE_READY_STATUS, 318 .has_pll_override = true, 319 .se_clk_scheme_default = true, 320 .autoresume_en = BIT(0), 321 .update_tune1_with_efuse = true, 322 }; 323 324 static const struct qusb2_phy_cfg ipq6018_phy_cfg = { 325 .tbl = ipq6018_init_tbl, 326 .tbl_num = ARRAY_SIZE(ipq6018_init_tbl), 327 .regs = ipq6018_regs_layout, 328 329 .disable_ctrl = POWER_DOWN, 330 .mask_core_ready = PLL_LOCKED, 331 /* autoresume not used */ 332 .autoresume_en = BIT(0), 333 }; 334 335 static const struct qusb2_phy_cfg qusb2_v2_phy_cfg = { 336 .tbl = qusb2_v2_init_tbl, 337 .tbl_num = ARRAY_SIZE(qusb2_v2_init_tbl), 338 .regs = qusb2_v2_regs_layout, 339 340 .disable_ctrl = (PWR_CTRL1_VREF_SUPPLY_TRIM | PWR_CTRL1_CLAMP_N_EN | 341 POWER_DOWN), 342 .mask_core_ready = CORE_READY_STATUS, 343 .has_pll_override = true, 344 .se_clk_scheme_default = true, 345 .autoresume_en = BIT(0), 346 .update_tune1_with_efuse = true, 347 }; 348 349 static const struct qusb2_phy_cfg sdm660_phy_cfg = { 350 .tbl = msm8996_init_tbl, 351 .tbl_num = ARRAY_SIZE(msm8996_init_tbl), 352 .regs = msm8996_regs_layout, 353 354 .has_pll_test = true, 355 .se_clk_scheme_default = false, 356 .disable_ctrl = (CLAMP_N_EN | FREEZIO_N | POWER_DOWN), 357 .mask_core_ready = PLL_LOCKED, 358 .autoresume_en = BIT(3), 359 }; 360 361 static const struct qusb2_phy_cfg sm6115_phy_cfg = { 362 .tbl = sm6115_init_tbl, 363 .tbl_num = ARRAY_SIZE(sm6115_init_tbl), 364 .regs = msm8996_regs_layout, 365 366 .has_pll_test = true, 367 .se_clk_scheme_default = true, 368 .disable_ctrl = (CLAMP_N_EN | FREEZIO_N | POWER_DOWN), 369 .mask_core_ready = PLL_LOCKED, 370 .autoresume_en = BIT(3), 371 }; 372 373 static const char * const qusb2_phy_vreg_names[] = { 374 "vdd", "vdda-pll", "vdda-phy-dpdm", 375 }; 376 377 #define QUSB2_NUM_VREGS ARRAY_SIZE(qusb2_phy_vreg_names) 378 379 /* struct override_param - structure holding qusb2 v2 phy overriding param 380 * set override true if the device tree property exists and read and assign 381 * to value 382 */ 383 struct override_param { 384 bool override; 385 u8 value; 386 }; 387 388 /*struct override_params - structure holding qusb2 v2 phy overriding params 389 * @imp_res_offset: rescode offset to be updated in IMP_CTRL1 register 390 * @hstx_trim: HSTX_TRIM to be updated in TUNE1 register 391 * @preemphasis: Amplitude Pre-Emphasis to be updated in TUNE1 register 392 * @preemphasis_width: half/full-width Pre-Emphasis updated via TUNE1 393 * @bias_ctrl: bias ctrl to be updated in BIAS_CONTROL_2 register 394 * @charge_ctrl: charge ctrl to be updated in CHG_CTRL2 register 395 * @hsdisc_trim: disconnect threshold to be updated in TUNE2 register 396 */ 397 struct override_params { 398 struct override_param imp_res_offset; 399 struct override_param hstx_trim; 400 struct override_param preemphasis; 401 struct override_param preemphasis_width; 402 struct override_param bias_ctrl; 403 struct override_param charge_ctrl; 404 struct override_param hsdisc_trim; 405 }; 406 407 /** 408 * struct qusb2_phy - structure holding qusb2 phy attributes 409 * 410 * @phy: generic phy 411 * @base: iomapped memory space for qubs2 phy 412 * 413 * @cfg_ahb_clk: AHB2PHY interface clock 414 * @ref_clk: phy reference clock 415 * @iface_clk: phy interface clock 416 * @phy_reset: phy reset control 417 * @vregs: regulator supplies bulk data 418 * 419 * @tcsr: TCSR syscon register map 420 * @cell: nvmem cell containing phy tuning value 421 * 422 * @overrides: pointer to structure for all overriding tuning params 423 * 424 * @cfg: phy config data 425 * @has_se_clk_scheme: indicate if PHY has single-ended ref clock scheme 426 * @phy_initialized: indicate if PHY has been initialized 427 * @mode: current PHY mode 428 */ 429 struct qusb2_phy { 430 struct phy *phy; 431 void __iomem *base; 432 433 struct clk *cfg_ahb_clk; 434 struct clk *ref_clk; 435 struct clk *iface_clk; 436 struct reset_control *phy_reset; 437 struct regulator_bulk_data vregs[QUSB2_NUM_VREGS]; 438 439 struct regmap *tcsr; 440 struct nvmem_cell *cell; 441 442 struct override_params overrides; 443 444 const struct qusb2_phy_cfg *cfg; 445 bool has_se_clk_scheme; 446 bool phy_initialized; 447 enum phy_mode mode; 448 }; 449 450 static inline void qusb2_write_mask(void __iomem *base, u32 offset, 451 u32 val, u32 mask) 452 { 453 u32 reg; 454 455 reg = readl(base + offset); 456 reg &= ~mask; 457 reg |= val & mask; 458 writel(reg, base + offset); 459 460 /* Ensure above write is completed */ 461 readl(base + offset); 462 } 463 464 static inline void qusb2_setbits(void __iomem *base, u32 offset, u32 val) 465 { 466 u32 reg; 467 468 reg = readl(base + offset); 469 reg |= val; 470 writel(reg, base + offset); 471 472 /* Ensure above write is completed */ 473 readl(base + offset); 474 } 475 476 static inline void qusb2_clrbits(void __iomem *base, u32 offset, u32 val) 477 { 478 u32 reg; 479 480 reg = readl(base + offset); 481 reg &= ~val; 482 writel(reg, base + offset); 483 484 /* Ensure above write is completed */ 485 readl(base + offset); 486 } 487 488 static inline 489 void qcom_qusb2_phy_configure(void __iomem *base, 490 const unsigned int *regs, 491 const struct qusb2_phy_init_tbl tbl[], int num) 492 { 493 int i; 494 495 for (i = 0; i < num; i++) { 496 if (tbl[i].in_layout) 497 writel(tbl[i].val, base + regs[tbl[i].offset]); 498 else 499 writel(tbl[i].val, base + tbl[i].offset); 500 } 501 } 502 503 /* 504 * Update board specific PHY tuning override values if specified from 505 * device tree. 506 */ 507 static void qusb2_phy_override_phy_params(struct qusb2_phy *qphy) 508 { 509 const struct qusb2_phy_cfg *cfg = qphy->cfg; 510 struct override_params *or = &qphy->overrides; 511 512 if (or->imp_res_offset.override) 513 qusb2_write_mask(qphy->base, QUSB2PHY_IMP_CTRL1, 514 or->imp_res_offset.value << IMP_RES_OFFSET_SHIFT, 515 IMP_RES_OFFSET_MASK); 516 517 if (or->bias_ctrl.override) 518 qusb2_write_mask(qphy->base, QUSB2PHY_PLL_BIAS_CONTROL_2, 519 or->bias_ctrl.value << BIAS_CTRL2_RES_OFFSET_SHIFT, 520 BIAS_CTRL2_RES_OFFSET_MASK); 521 522 if (or->charge_ctrl.override) 523 qusb2_write_mask(qphy->base, QUSB2PHY_CHG_CTRL2, 524 or->charge_ctrl.value << CHG_CTRL2_OFFSET_SHIFT, 525 CHG_CTRL2_OFFSET_MASK); 526 527 if (or->hstx_trim.override) 528 qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1], 529 or->hstx_trim.value << HSTX_TRIM_SHIFT, 530 HSTX_TRIM_MASK); 531 532 if (or->preemphasis.override) 533 qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1], 534 or->preemphasis.value << PREEMPHASIS_EN_SHIFT, 535 PREEMPHASIS_EN_MASK); 536 537 if (or->preemphasis_width.override) { 538 if (or->preemphasis_width.value == 539 QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT) 540 qusb2_setbits(qphy->base, 541 cfg->regs[QUSB2PHY_PORT_TUNE1], 542 PREEMPH_WIDTH_HALF_BIT); 543 else 544 qusb2_clrbits(qphy->base, 545 cfg->regs[QUSB2PHY_PORT_TUNE1], 546 PREEMPH_WIDTH_HALF_BIT); 547 } 548 549 if (or->hsdisc_trim.override) 550 qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE2], 551 or->hsdisc_trim.value << HSDISC_TRIM_SHIFT, 552 HSDISC_TRIM_MASK); 553 } 554 555 /* 556 * Fetches HS Tx tuning value from nvmem and sets the 557 * QUSB2PHY_PORT_TUNE1/2 register. 558 * For error case, skip setting the value and use the default value. 559 */ 560 static void qusb2_phy_set_tune2_param(struct qusb2_phy *qphy) 561 { 562 struct device *dev = &qphy->phy->dev; 563 const struct qusb2_phy_cfg *cfg = qphy->cfg; 564 u8 *val, hstx_trim; 565 566 /* efuse register is optional */ 567 if (!qphy->cell) 568 return; 569 570 /* 571 * Read efuse register having TUNE2/1 parameter's high nibble. 572 * If efuse register shows value as 0x0 (indicating value is not 573 * fused), or if we fail to find a valid efuse register setting, 574 * then use default value for high nibble that we have already 575 * set while configuring the phy. 576 */ 577 val = nvmem_cell_read(qphy->cell, NULL); 578 if (IS_ERR(val)) { 579 dev_dbg(dev, "failed to read a valid hs-tx trim value\n"); 580 return; 581 } 582 hstx_trim = val[0]; 583 kfree(val); 584 if (!hstx_trim) { 585 dev_dbg(dev, "failed to read a valid hs-tx trim value\n"); 586 return; 587 } 588 589 /* Fused TUNE1/2 value is the higher nibble only */ 590 if (cfg->update_tune1_with_efuse) 591 qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1], 592 hstx_trim << HSTX_TRIM_SHIFT, HSTX_TRIM_MASK); 593 else 594 qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE2], 595 hstx_trim << HSTX_TRIM_SHIFT, HSTX_TRIM_MASK); 596 } 597 598 static int qusb2_phy_set_mode(struct phy *phy, 599 enum phy_mode mode, int submode) 600 { 601 struct qusb2_phy *qphy = phy_get_drvdata(phy); 602 603 qphy->mode = mode; 604 605 return 0; 606 } 607 608 static int __maybe_unused qusb2_phy_runtime_suspend(struct device *dev) 609 { 610 struct qusb2_phy *qphy = dev_get_drvdata(dev); 611 const struct qusb2_phy_cfg *cfg = qphy->cfg; 612 u32 intr_mask; 613 614 dev_vdbg(dev, "Suspending QUSB2 Phy, mode:%d\n", qphy->mode); 615 616 if (!qphy->phy_initialized) { 617 dev_vdbg(dev, "PHY not initialized, bailing out\n"); 618 return 0; 619 } 620 621 /* 622 * Enable DP/DM interrupts to detect line state changes based on current 623 * speed. In other words, enable the triggers _opposite_ of what the 624 * current D+/D- levels are e.g. if currently D+ high, D- low 625 * (HS 'J'/Suspend), configure the mask to trigger on D+ low OR D- high 626 */ 627 intr_mask = DPSE_INTR_EN | DMSE_INTR_EN; 628 switch (qphy->mode) { 629 case PHY_MODE_USB_HOST_HS: 630 case PHY_MODE_USB_HOST_FS: 631 case PHY_MODE_USB_DEVICE_HS: 632 case PHY_MODE_USB_DEVICE_FS: 633 intr_mask |= DMSE_INTR_HIGH_SEL; 634 break; 635 case PHY_MODE_USB_HOST_LS: 636 case PHY_MODE_USB_DEVICE_LS: 637 intr_mask |= DPSE_INTR_HIGH_SEL; 638 break; 639 default: 640 /* No device connected, enable both DP/DM high interrupt */ 641 intr_mask |= DMSE_INTR_HIGH_SEL; 642 intr_mask |= DPSE_INTR_HIGH_SEL; 643 break; 644 } 645 646 writel(intr_mask, qphy->base + cfg->regs[QUSB2PHY_INTR_CTRL]); 647 648 /* hold core PLL into reset */ 649 if (cfg->has_pll_override) { 650 qusb2_setbits(qphy->base, 651 cfg->regs[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE], 652 CORE_PLL_EN_FROM_RESET | CORE_RESET | 653 CORE_RESET_MUX); 654 } 655 656 /* enable phy auto-resume only if device is connected on bus */ 657 if (qphy->mode != PHY_MODE_INVALID) { 658 qusb2_setbits(qphy->base, cfg->regs[QUSB2PHY_PORT_TEST1], 659 cfg->autoresume_en); 660 /* Autoresume bit has to be toggled in order to enable it */ 661 qusb2_clrbits(qphy->base, cfg->regs[QUSB2PHY_PORT_TEST1], 662 cfg->autoresume_en); 663 } 664 665 if (!qphy->has_se_clk_scheme) 666 clk_disable_unprepare(qphy->ref_clk); 667 668 clk_disable_unprepare(qphy->cfg_ahb_clk); 669 clk_disable_unprepare(qphy->iface_clk); 670 671 return 0; 672 } 673 674 static int __maybe_unused qusb2_phy_runtime_resume(struct device *dev) 675 { 676 struct qusb2_phy *qphy = dev_get_drvdata(dev); 677 const struct qusb2_phy_cfg *cfg = qphy->cfg; 678 int ret; 679 680 dev_vdbg(dev, "Resuming QUSB2 phy, mode:%d\n", qphy->mode); 681 682 if (!qphy->phy_initialized) { 683 dev_vdbg(dev, "PHY not initialized, bailing out\n"); 684 return 0; 685 } 686 687 ret = clk_prepare_enable(qphy->iface_clk); 688 if (ret) { 689 dev_err(dev, "failed to enable iface_clk, %d\n", ret); 690 return ret; 691 } 692 693 ret = clk_prepare_enable(qphy->cfg_ahb_clk); 694 if (ret) { 695 dev_err(dev, "failed to enable cfg ahb clock, %d\n", ret); 696 goto disable_iface_clk; 697 } 698 699 if (!qphy->has_se_clk_scheme) { 700 ret = clk_prepare_enable(qphy->ref_clk); 701 if (ret) { 702 dev_err(dev, "failed to enable ref clk, %d\n", ret); 703 goto disable_ahb_clk; 704 } 705 } 706 707 writel(0x0, qphy->base + cfg->regs[QUSB2PHY_INTR_CTRL]); 708 709 /* bring core PLL out of reset */ 710 if (cfg->has_pll_override) { 711 qusb2_clrbits(qphy->base, 712 cfg->regs[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE], 713 CORE_RESET | CORE_RESET_MUX); 714 } 715 716 return 0; 717 718 disable_ahb_clk: 719 clk_disable_unprepare(qphy->cfg_ahb_clk); 720 disable_iface_clk: 721 clk_disable_unprepare(qphy->iface_clk); 722 723 return ret; 724 } 725 726 static int qusb2_phy_init(struct phy *phy) 727 { 728 struct qusb2_phy *qphy = phy_get_drvdata(phy); 729 const struct qusb2_phy_cfg *cfg = qphy->cfg; 730 unsigned int val = 0; 731 unsigned int clk_scheme; 732 int ret; 733 734 dev_vdbg(&phy->dev, "%s(): Initializing QUSB2 phy\n", __func__); 735 736 /* turn on regulator supplies */ 737 ret = regulator_bulk_enable(ARRAY_SIZE(qphy->vregs), qphy->vregs); 738 if (ret) 739 return ret; 740 741 ret = clk_prepare_enable(qphy->iface_clk); 742 if (ret) { 743 dev_err(&phy->dev, "failed to enable iface_clk, %d\n", ret); 744 goto poweroff_phy; 745 } 746 747 /* enable ahb interface clock to program phy */ 748 ret = clk_prepare_enable(qphy->cfg_ahb_clk); 749 if (ret) { 750 dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret); 751 goto disable_iface_clk; 752 } 753 754 /* Perform phy reset */ 755 ret = reset_control_assert(qphy->phy_reset); 756 if (ret) { 757 dev_err(&phy->dev, "failed to assert phy_reset, %d\n", ret); 758 goto disable_ahb_clk; 759 } 760 761 /* 100 us delay to keep PHY in reset mode */ 762 usleep_range(100, 150); 763 764 ret = reset_control_deassert(qphy->phy_reset); 765 if (ret) { 766 dev_err(&phy->dev, "failed to de-assert phy_reset, %d\n", ret); 767 goto disable_ahb_clk; 768 } 769 770 /* Disable the PHY */ 771 qusb2_setbits(qphy->base, cfg->regs[QUSB2PHY_PORT_POWERDOWN], 772 qphy->cfg->disable_ctrl); 773 774 if (cfg->has_pll_test) { 775 /* save reset value to override reference clock scheme later */ 776 val = readl(qphy->base + QUSB2PHY_PLL_TEST); 777 } 778 779 qcom_qusb2_phy_configure(qphy->base, cfg->regs, cfg->tbl, 780 cfg->tbl_num); 781 782 /* Override board specific PHY tuning values */ 783 qusb2_phy_override_phy_params(qphy); 784 785 /* Set efuse value for tuning the PHY */ 786 qusb2_phy_set_tune2_param(qphy); 787 788 /* Enable the PHY */ 789 qusb2_clrbits(qphy->base, cfg->regs[QUSB2PHY_PORT_POWERDOWN], 790 POWER_DOWN); 791 792 /* Required to get phy pll lock successfully */ 793 usleep_range(150, 160); 794 795 /* 796 * Not all the SoCs have got a readable TCSR_PHY_CLK_SCHEME 797 * register in the TCSR so, if there's none, use the default 798 * value hardcoded in the configuration. 799 */ 800 qphy->has_se_clk_scheme = cfg->se_clk_scheme_default; 801 802 /* 803 * read TCSR_PHY_CLK_SCHEME register to check if single-ended 804 * clock scheme is selected. If yes, then disable differential 805 * ref_clk and use single-ended clock, otherwise use differential 806 * ref_clk only. 807 */ 808 if (qphy->tcsr) { 809 ret = regmap_read(qphy->tcsr, qphy->cfg->clk_scheme_offset, 810 &clk_scheme); 811 if (ret) { 812 dev_err(&phy->dev, "failed to read clk scheme reg\n"); 813 goto assert_phy_reset; 814 } 815 816 /* is it a differential clock scheme ? */ 817 if (!(clk_scheme & PHY_CLK_SCHEME_SEL)) { 818 dev_vdbg(&phy->dev, "%s(): select differential clk\n", 819 __func__); 820 qphy->has_se_clk_scheme = false; 821 } else { 822 dev_vdbg(&phy->dev, "%s(): select single-ended clk\n", 823 __func__); 824 } 825 } 826 827 if (!qphy->has_se_clk_scheme) { 828 ret = clk_prepare_enable(qphy->ref_clk); 829 if (ret) { 830 dev_err(&phy->dev, "failed to enable ref clk, %d\n", 831 ret); 832 goto assert_phy_reset; 833 } 834 } 835 836 if (cfg->has_pll_test) { 837 if (!qphy->has_se_clk_scheme) 838 val &= ~CLK_REF_SEL; 839 else 840 val |= CLK_REF_SEL; 841 842 writel(val, qphy->base + QUSB2PHY_PLL_TEST); 843 844 /* ensure above write is through */ 845 readl(qphy->base + QUSB2PHY_PLL_TEST); 846 } 847 848 /* Required to get phy pll lock successfully */ 849 usleep_range(100, 110); 850 851 val = readb(qphy->base + cfg->regs[QUSB2PHY_PLL_STATUS]); 852 if (!(val & cfg->mask_core_ready)) { 853 dev_err(&phy->dev, 854 "QUSB2PHY pll lock failed: status reg = %x\n", val); 855 ret = -EBUSY; 856 goto disable_ref_clk; 857 } 858 qphy->phy_initialized = true; 859 860 return 0; 861 862 disable_ref_clk: 863 if (!qphy->has_se_clk_scheme) 864 clk_disable_unprepare(qphy->ref_clk); 865 assert_phy_reset: 866 reset_control_assert(qphy->phy_reset); 867 disable_ahb_clk: 868 clk_disable_unprepare(qphy->cfg_ahb_clk); 869 disable_iface_clk: 870 clk_disable_unprepare(qphy->iface_clk); 871 poweroff_phy: 872 regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs); 873 874 return ret; 875 } 876 877 static int qusb2_phy_exit(struct phy *phy) 878 { 879 struct qusb2_phy *qphy = phy_get_drvdata(phy); 880 881 /* Disable the PHY */ 882 qusb2_setbits(qphy->base, qphy->cfg->regs[QUSB2PHY_PORT_POWERDOWN], 883 qphy->cfg->disable_ctrl); 884 885 if (!qphy->has_se_clk_scheme) 886 clk_disable_unprepare(qphy->ref_clk); 887 888 reset_control_assert(qphy->phy_reset); 889 890 clk_disable_unprepare(qphy->cfg_ahb_clk); 891 clk_disable_unprepare(qphy->iface_clk); 892 893 regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs); 894 895 qphy->phy_initialized = false; 896 897 return 0; 898 } 899 900 static const struct phy_ops qusb2_phy_gen_ops = { 901 .init = qusb2_phy_init, 902 .exit = qusb2_phy_exit, 903 .set_mode = qusb2_phy_set_mode, 904 .owner = THIS_MODULE, 905 }; 906 907 static const struct of_device_id qusb2_phy_of_match_table[] = { 908 { 909 .compatible = "qcom,ipq6018-qusb2-phy", 910 .data = &ipq6018_phy_cfg, 911 }, { 912 .compatible = "qcom,ipq8074-qusb2-phy", 913 .data = &msm8996_phy_cfg, 914 }, { 915 .compatible = "qcom,ipq9574-qusb2-phy", 916 .data = &ipq6018_phy_cfg, 917 }, { 918 .compatible = "qcom,msm8953-qusb2-phy", 919 .data = &msm8996_phy_cfg, 920 }, { 921 .compatible = "qcom,msm8996-qusb2-phy", 922 .data = &msm8996_phy_cfg, 923 }, { 924 .compatible = "qcom,msm8998-qusb2-phy", 925 .data = &msm8998_phy_cfg, 926 }, { 927 .compatible = "qcom,qcm2290-qusb2-phy", 928 .data = &sm6115_phy_cfg, 929 }, { 930 .compatible = "qcom,sdm660-qusb2-phy", 931 .data = &sdm660_phy_cfg, 932 }, { 933 .compatible = "qcom,sm4250-qusb2-phy", 934 .data = &sm6115_phy_cfg, 935 }, { 936 .compatible = "qcom,sm6115-qusb2-phy", 937 .data = &sm6115_phy_cfg, 938 }, { 939 /* 940 * Deprecated. Only here to support legacy device 941 * trees that didn't include "qcom,qusb2-v2-phy" 942 */ 943 .compatible = "qcom,sdm845-qusb2-phy", 944 .data = &qusb2_v2_phy_cfg, 945 }, { 946 .compatible = "qcom,qusb2-v2-phy", 947 .data = &qusb2_v2_phy_cfg, 948 }, 949 { }, 950 }; 951 MODULE_DEVICE_TABLE(of, qusb2_phy_of_match_table); 952 953 static const struct dev_pm_ops qusb2_phy_pm_ops = { 954 SET_RUNTIME_PM_OPS(qusb2_phy_runtime_suspend, 955 qusb2_phy_runtime_resume, NULL) 956 }; 957 958 static int qusb2_phy_probe(struct platform_device *pdev) 959 { 960 struct device *dev = &pdev->dev; 961 struct qusb2_phy *qphy; 962 struct phy_provider *phy_provider; 963 struct phy *generic_phy; 964 int ret, i; 965 int num; 966 u32 value; 967 struct override_params *or; 968 969 qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL); 970 if (!qphy) 971 return -ENOMEM; 972 or = &qphy->overrides; 973 974 qphy->base = devm_platform_ioremap_resource(pdev, 0); 975 if (IS_ERR(qphy->base)) 976 return PTR_ERR(qphy->base); 977 978 qphy->cfg_ahb_clk = devm_clk_get(dev, "cfg_ahb"); 979 if (IS_ERR(qphy->cfg_ahb_clk)) 980 return dev_err_probe(dev, PTR_ERR(qphy->cfg_ahb_clk), 981 "failed to get cfg ahb clk\n"); 982 983 qphy->ref_clk = devm_clk_get(dev, "ref"); 984 if (IS_ERR(qphy->ref_clk)) 985 return dev_err_probe(dev, PTR_ERR(qphy->ref_clk), 986 "failed to get ref clk\n"); 987 988 qphy->iface_clk = devm_clk_get_optional(dev, "iface"); 989 if (IS_ERR(qphy->iface_clk)) 990 return PTR_ERR(qphy->iface_clk); 991 992 qphy->phy_reset = devm_reset_control_get_by_index(&pdev->dev, 0); 993 if (IS_ERR(qphy->phy_reset)) { 994 dev_err(dev, "failed to get phy core reset\n"); 995 return PTR_ERR(qphy->phy_reset); 996 } 997 998 num = ARRAY_SIZE(qphy->vregs); 999 for (i = 0; i < num; i++) 1000 qphy->vregs[i].supply = qusb2_phy_vreg_names[i]; 1001 1002 ret = devm_regulator_bulk_get(dev, num, qphy->vregs); 1003 if (ret) 1004 return dev_err_probe(dev, ret, 1005 "failed to get regulator supplies\n"); 1006 1007 /* Get the specific init parameters of QMP phy */ 1008 qphy->cfg = of_device_get_match_data(dev); 1009 1010 qphy->tcsr = syscon_regmap_lookup_by_phandle(dev->of_node, 1011 "qcom,tcsr-syscon"); 1012 if (IS_ERR(qphy->tcsr)) { 1013 dev_dbg(dev, "failed to lookup TCSR regmap\n"); 1014 qphy->tcsr = NULL; 1015 } 1016 1017 qphy->cell = devm_nvmem_cell_get(dev, NULL); 1018 if (IS_ERR(qphy->cell)) { 1019 if (PTR_ERR(qphy->cell) == -EPROBE_DEFER) 1020 return -EPROBE_DEFER; 1021 qphy->cell = NULL; 1022 dev_dbg(dev, "failed to lookup tune2 hstx trim value\n"); 1023 } 1024 1025 if (!of_property_read_u32(dev->of_node, "qcom,imp-res-offset-value", 1026 &value)) { 1027 or->imp_res_offset.value = (u8)value; 1028 or->imp_res_offset.override = true; 1029 } 1030 1031 if (!of_property_read_u32(dev->of_node, "qcom,bias-ctrl-value", 1032 &value)) { 1033 or->bias_ctrl.value = (u8)value; 1034 or->bias_ctrl.override = true; 1035 } 1036 1037 if (!of_property_read_u32(dev->of_node, "qcom,charge-ctrl-value", 1038 &value)) { 1039 or->charge_ctrl.value = (u8)value; 1040 or->charge_ctrl.override = true; 1041 } 1042 1043 if (!of_property_read_u32(dev->of_node, "qcom,hstx-trim-value", 1044 &value)) { 1045 or->hstx_trim.value = (u8)value; 1046 or->hstx_trim.override = true; 1047 } 1048 1049 if (!of_property_read_u32(dev->of_node, "qcom,preemphasis-level", 1050 &value)) { 1051 or->preemphasis.value = (u8)value; 1052 or->preemphasis.override = true; 1053 } 1054 1055 if (!of_property_read_u32(dev->of_node, "qcom,preemphasis-width", 1056 &value)) { 1057 or->preemphasis_width.value = (u8)value; 1058 or->preemphasis_width.override = true; 1059 } 1060 1061 if (!of_property_read_u32(dev->of_node, "qcom,hsdisc-trim-value", 1062 &value)) { 1063 or->hsdisc_trim.value = (u8)value; 1064 or->hsdisc_trim.override = true; 1065 } 1066 1067 pm_runtime_set_active(dev); 1068 pm_runtime_enable(dev); 1069 /* 1070 * Prevent runtime pm from being ON by default. Users can enable 1071 * it using power/control in sysfs. 1072 */ 1073 pm_runtime_forbid(dev); 1074 1075 generic_phy = devm_phy_create(dev, NULL, &qusb2_phy_gen_ops); 1076 if (IS_ERR(generic_phy)) { 1077 ret = PTR_ERR(generic_phy); 1078 dev_err(dev, "failed to create phy, %d\n", ret); 1079 pm_runtime_disable(dev); 1080 return ret; 1081 } 1082 qphy->phy = generic_phy; 1083 1084 dev_set_drvdata(dev, qphy); 1085 phy_set_drvdata(generic_phy, qphy); 1086 1087 phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); 1088 if (!IS_ERR(phy_provider)) 1089 dev_info(dev, "Registered Qcom-QUSB2 phy\n"); 1090 else 1091 pm_runtime_disable(dev); 1092 1093 return PTR_ERR_OR_ZERO(phy_provider); 1094 } 1095 1096 static struct platform_driver qusb2_phy_driver = { 1097 .probe = qusb2_phy_probe, 1098 .driver = { 1099 .name = "qcom-qusb2-phy", 1100 .pm = &qusb2_phy_pm_ops, 1101 .of_match_table = qusb2_phy_of_match_table, 1102 }, 1103 }; 1104 1105 module_platform_driver(qusb2_phy_driver); 1106 1107 MODULE_AUTHOR("Vivek Gautam <vivek.gautam@codeaurora.org>"); 1108 MODULE_DESCRIPTION("Qualcomm QUSB2 PHY driver"); 1109 MODULE_LICENSE("GPL v2"); 1110