1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * Copyright (c) 2015 MediaTek Inc.
4  * Author: Chunfeng Yun <chunfeng.yun@mediatek.com>
5  *
6  */
7 
8 #include <dt-bindings/phy/phy.h>
9 #include <linux/clk.h>
10 #include <linux/delay.h>
11 #include <linux/iopoll.h>
12 #include <linux/mfd/syscon.h>
13 #include <linux/module.h>
14 #include <linux/nvmem-consumer.h>
15 #include <linux/of_address.h>
16 #include <linux/of_device.h>
17 #include <linux/phy/phy.h>
18 #include <linux/platform_device.h>
19 #include <linux/regmap.h>
20 
21 #include "phy-mtk-io.h"
22 
23 /* version V1 sub-banks offset base address */
24 /* banks shared by multiple phys */
25 #define SSUSB_SIFSLV_V1_SPLLC		0x000	/* shared by u3 phys */
26 #define SSUSB_SIFSLV_V1_U2FREQ		0x100	/* shared by u2 phys */
27 #define SSUSB_SIFSLV_V1_CHIP		0x300	/* shared by u3 phys */
28 /* u2 phy bank */
29 #define SSUSB_SIFSLV_V1_U2PHY_COM	0x000
30 /* u3/pcie/sata phy banks */
31 #define SSUSB_SIFSLV_V1_U3PHYD		0x000
32 #define SSUSB_SIFSLV_V1_U3PHYA		0x200
33 
34 /* version V2/V3 sub-banks offset base address */
35 /* V3: U2FREQ is not used anymore, but reserved */
36 /* u2 phy banks */
37 #define SSUSB_SIFSLV_V2_MISC		0x000
38 #define SSUSB_SIFSLV_V2_U2FREQ		0x100
39 #define SSUSB_SIFSLV_V2_U2PHY_COM	0x300
40 /* u3/pcie/sata phy banks */
41 #define SSUSB_SIFSLV_V2_SPLLC		0x000
42 #define SSUSB_SIFSLV_V2_CHIP		0x100
43 #define SSUSB_SIFSLV_V2_U3PHYD		0x200
44 #define SSUSB_SIFSLV_V2_U3PHYA		0x400
45 
46 #define U3P_MISC_REG1		0x04
47 #define MR1_EFUSE_AUTO_LOAD_DIS		BIT(6)
48 
49 #define U3P_USBPHYACR0		0x000
50 #define PA0_RG_U2PLL_FORCE_ON		BIT(15)
51 #define PA0_USB20_PLL_PREDIV		GENMASK(7, 6)
52 #define PA0_USB20_PLL_PREDIV_VAL(x)	((0x3 & (x)) << 6)
53 #define PA0_RG_USB20_INTR_EN		BIT(5)
54 
55 #define U3P_USBPHYACR1		0x004
56 #define PA1_RG_INTR_CAL		GENMASK(23, 19)
57 #define PA1_RG_INTR_CAL_VAL(x)	((0x1f & (x)) << 19)
58 #define PA1_RG_VRT_SEL			GENMASK(14, 12)
59 #define PA1_RG_VRT_SEL_VAL(x)	((0x7 & (x)) << 12)
60 #define PA1_RG_TERM_SEL		GENMASK(10, 8)
61 #define PA1_RG_TERM_SEL_VAL(x)	((0x7 & (x)) << 8)
62 
63 #define U3P_USBPHYACR2		0x008
64 #define PA2_RG_U2PLL_BW			GENMASK(21, 19)
65 #define PA2_RG_U2PLL_BW_VAL(x)		((0x7 & (x)) << 19)
66 #define PA2_RG_SIF_U2PLL_FORCE_EN	BIT(18)
67 
68 #define U3P_USBPHYACR5		0x014
69 #define PA5_RG_U2_HSTX_SRCAL_EN	BIT(15)
70 #define PA5_RG_U2_HSTX_SRCTRL		GENMASK(14, 12)
71 #define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
72 #define PA5_RG_U2_HS_100U_U3_EN	BIT(11)
73 
74 #define U3P_USBPHYACR6		0x018
75 #define PA6_RG_U2_BC11_SW_EN		BIT(23)
76 #define PA6_RG_U2_OTG_VBUSCMP_EN	BIT(20)
77 #define PA6_RG_U2_DISCTH		GENMASK(7, 4)
78 #define PA6_RG_U2_DISCTH_VAL(x)	((0xf & (x)) << 4)
79 #define PA6_RG_U2_SQTH		GENMASK(3, 0)
80 #define PA6_RG_U2_SQTH_VAL(x)	(0xf & (x))
81 
82 #define U3P_U2PHYACR4		0x020
83 #define P2C_RG_USB20_GPIO_CTL		BIT(9)
84 #define P2C_USB20_GPIO_MODE		BIT(8)
85 #define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
86 
87 #define U3P_U2PHYA_RESV		0x030
88 #define P2R_RG_U2PLL_FBDIV_26M		0x1bb13b
89 #define P2R_RG_U2PLL_FBDIV_48M		0x3c0000
90 
91 #define U3P_U2PHYA_RESV1	0x044
92 #define P2R_RG_U2PLL_REFCLK_SEL	BIT(5)
93 #define P2R_RG_U2PLL_FRA_EN		BIT(3)
94 
95 #define U3D_U2PHYDCR0		0x060
96 #define P2C_RG_SIF_U2PLL_FORCE_ON	BIT(24)
97 
98 #define U3P_U2PHYDTM0		0x068
99 #define P2C_FORCE_UART_EN		BIT(26)
100 #define P2C_FORCE_DATAIN		BIT(23)
101 #define P2C_FORCE_DM_PULLDOWN		BIT(21)
102 #define P2C_FORCE_DP_PULLDOWN		BIT(20)
103 #define P2C_FORCE_XCVRSEL		BIT(19)
104 #define P2C_FORCE_SUSPENDM		BIT(18)
105 #define P2C_FORCE_TERMSEL		BIT(17)
106 #define P2C_RG_DATAIN			GENMASK(13, 10)
107 #define P2C_RG_DATAIN_VAL(x)		((0xf & (x)) << 10)
108 #define P2C_RG_DMPULLDOWN		BIT(7)
109 #define P2C_RG_DPPULLDOWN		BIT(6)
110 #define P2C_RG_XCVRSEL			GENMASK(5, 4)
111 #define P2C_RG_XCVRSEL_VAL(x)		((0x3 & (x)) << 4)
112 #define P2C_RG_SUSPENDM			BIT(3)
113 #define P2C_RG_TERMSEL			BIT(2)
114 #define P2C_DTM0_PART_MASK \
115 		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
116 		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
117 		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
118 		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
119 
120 #define U3P_U2PHYDTM1		0x06C
121 #define P2C_RG_UART_EN			BIT(16)
122 #define P2C_FORCE_IDDIG		BIT(9)
123 #define P2C_RG_VBUSVALID		BIT(5)
124 #define P2C_RG_SESSEND			BIT(4)
125 #define P2C_RG_AVALID			BIT(2)
126 #define P2C_RG_IDDIG			BIT(1)
127 
128 #define U3P_U2PHYBC12C		0x080
129 #define P2C_RG_CHGDT_EN		BIT(0)
130 
131 #define U3P_U3_CHIP_GPIO_CTLD		0x0c
132 #define P3C_REG_IP_SW_RST		BIT(31)
133 #define P3C_MCU_BUS_CK_GATE_EN		BIT(30)
134 #define P3C_FORCE_IP_SW_RST		BIT(29)
135 
136 #define U3P_U3_CHIP_GPIO_CTLE		0x10
137 #define P3C_RG_SWRST_U3_PHYD		BIT(25)
138 #define P3C_RG_SWRST_U3_PHYD_FORCE_EN	BIT(24)
139 
140 #define U3P_U3_PHYA_REG0	0x000
141 #define P3A_RG_IEXT_INTR		GENMASK(15, 10)
142 #define P3A_RG_IEXT_INTR_VAL(x)		((0x3f & (x)) << 10)
143 #define P3A_RG_CLKDRV_OFF		GENMASK(3, 2)
144 #define P3A_RG_CLKDRV_OFF_VAL(x)	((0x3 & (x)) << 2)
145 
146 #define U3P_U3_PHYA_REG1	0x004
147 #define P3A_RG_CLKDRV_AMP		GENMASK(31, 29)
148 #define P3A_RG_CLKDRV_AMP_VAL(x)	((0x7 & (x)) << 29)
149 
150 #define U3P_U3_PHYA_REG6	0x018
151 #define P3A_RG_TX_EIDLE_CM		GENMASK(31, 28)
152 #define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
153 
154 #define U3P_U3_PHYA_REG9	0x024
155 #define P3A_RG_RX_DAC_MUX		GENMASK(5, 1)
156 #define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
157 
158 #define U3P_U3_PHYA_DA_REG0	0x100
159 #define P3A_RG_XTAL_EXT_PE2H		GENMASK(17, 16)
160 #define P3A_RG_XTAL_EXT_PE2H_VAL(x)	((0x3 & (x)) << 16)
161 #define P3A_RG_XTAL_EXT_PE1H		GENMASK(13, 12)
162 #define P3A_RG_XTAL_EXT_PE1H_VAL(x)	((0x3 & (x)) << 12)
163 #define P3A_RG_XTAL_EXT_EN_U3		GENMASK(11, 10)
164 #define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
165 
166 #define U3P_U3_PHYA_DA_REG4	0x108
167 #define P3A_RG_PLL_DIVEN_PE2H		GENMASK(21, 19)
168 #define P3A_RG_PLL_BC_PE2H		GENMASK(7, 6)
169 #define P3A_RG_PLL_BC_PE2H_VAL(x)	((0x3 & (x)) << 6)
170 
171 #define U3P_U3_PHYA_DA_REG5	0x10c
172 #define P3A_RG_PLL_BR_PE2H		GENMASK(29, 28)
173 #define P3A_RG_PLL_BR_PE2H_VAL(x)	((0x3 & (x)) << 28)
174 #define P3A_RG_PLL_IC_PE2H		GENMASK(15, 12)
175 #define P3A_RG_PLL_IC_PE2H_VAL(x)	((0xf & (x)) << 12)
176 
177 #define U3P_U3_PHYA_DA_REG6	0x110
178 #define P3A_RG_PLL_IR_PE2H		GENMASK(19, 16)
179 #define P3A_RG_PLL_IR_PE2H_VAL(x)	((0xf & (x)) << 16)
180 
181 #define U3P_U3_PHYA_DA_REG7	0x114
182 #define P3A_RG_PLL_BP_PE2H		GENMASK(19, 16)
183 #define P3A_RG_PLL_BP_PE2H_VAL(x)	((0xf & (x)) << 16)
184 
185 #define U3P_U3_PHYA_DA_REG20	0x13c
186 #define P3A_RG_PLL_DELTA1_PE2H		GENMASK(31, 16)
187 #define P3A_RG_PLL_DELTA1_PE2H_VAL(x)	((0xffff & (x)) << 16)
188 
189 #define U3P_U3_PHYA_DA_REG25	0x148
190 #define P3A_RG_PLL_DELTA_PE2H		GENMASK(15, 0)
191 #define P3A_RG_PLL_DELTA_PE2H_VAL(x)	(0xffff & (x))
192 
193 #define U3P_U3_PHYD_LFPS1		0x00c
194 #define P3D_RG_FWAKE_TH		GENMASK(21, 16)
195 #define P3D_RG_FWAKE_TH_VAL(x)	((0x3f & (x)) << 16)
196 
197 #define U3P_U3_PHYD_IMPCAL0		0x010
198 #define P3D_RG_FORCE_TX_IMPEL		BIT(31)
199 #define P3D_RG_TX_IMPEL			GENMASK(28, 24)
200 #define P3D_RG_TX_IMPEL_VAL(x)		((0x1f & (x)) << 24)
201 
202 #define U3P_U3_PHYD_IMPCAL1		0x014
203 #define P3D_RG_FORCE_RX_IMPEL		BIT(31)
204 #define P3D_RG_RX_IMPEL			GENMASK(28, 24)
205 #define P3D_RG_RX_IMPEL_VAL(x)		((0x1f & (x)) << 24)
206 
207 #define U3P_U3_PHYD_RSV			0x054
208 #define P3D_RG_EFUSE_AUTO_LOAD_DIS	BIT(12)
209 
210 #define U3P_U3_PHYD_CDR1		0x05c
211 #define P3D_RG_CDR_BIR_LTD1		GENMASK(28, 24)
212 #define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
213 #define P3D_RG_CDR_BIR_LTD0		GENMASK(12, 8)
214 #define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
215 
216 #define U3P_U3_PHYD_RXDET1		0x128
217 #define P3D_RG_RXDET_STB2_SET		GENMASK(17, 9)
218 #define P3D_RG_RXDET_STB2_SET_VAL(x)	((0x1ff & (x)) << 9)
219 
220 #define U3P_U3_PHYD_RXDET2		0x12c
221 #define P3D_RG_RXDET_STB2_SET_P3	GENMASK(8, 0)
222 #define P3D_RG_RXDET_STB2_SET_P3_VAL(x)	(0x1ff & (x))
223 
224 #define U3P_SPLLC_XTALCTL3		0x018
225 #define XC3_RG_U3_XTAL_RX_PWD		BIT(9)
226 #define XC3_RG_U3_FRC_XTAL_RX_PWD	BIT(8)
227 
228 #define U3P_U2FREQ_FMCR0	0x00
229 #define P2F_RG_MONCLK_SEL	GENMASK(27, 26)
230 #define P2F_RG_MONCLK_SEL_VAL(x)	((0x3 & (x)) << 26)
231 #define P2F_RG_FREQDET_EN	BIT(24)
232 #define P2F_RG_CYCLECNT		GENMASK(23, 0)
233 #define P2F_RG_CYCLECNT_VAL(x)	((P2F_RG_CYCLECNT) & (x))
234 
235 #define U3P_U2FREQ_VALUE	0x0c
236 
237 #define U3P_U2FREQ_FMMONR1	0x10
238 #define P2F_USB_FM_VALID	BIT(0)
239 #define P2F_RG_FRCK_EN		BIT(8)
240 
241 #define U3P_REF_CLK		26	/* MHZ */
242 #define U3P_SLEW_RATE_COEF	28
243 #define U3P_SR_COEF_DIVISOR	1000
244 #define U3P_FM_DET_CYCLE_CNT	1024
245 
246 /* SATA register setting */
247 #define PHYD_CTRL_SIGNAL_MODE4		0x1c
248 /* CDR Charge Pump P-path current adjustment */
249 #define RG_CDR_BICLTD1_GEN1_MSK		GENMASK(23, 20)
250 #define RG_CDR_BICLTD1_GEN1_VAL(x)	((0xf & (x)) << 20)
251 #define RG_CDR_BICLTD0_GEN1_MSK		GENMASK(11, 8)
252 #define RG_CDR_BICLTD0_GEN1_VAL(x)	((0xf & (x)) << 8)
253 
254 #define PHYD_DESIGN_OPTION2		0x24
255 /* Symbol lock count selection */
256 #define RG_LOCK_CNT_SEL_MSK		GENMASK(5, 4)
257 #define RG_LOCK_CNT_SEL_VAL(x)		((0x3 & (x)) << 4)
258 
259 #define PHYD_DESIGN_OPTION9	0x40
260 /* COMWAK GAP width window */
261 #define RG_TG_MAX_MSK		GENMASK(20, 16)
262 #define RG_TG_MAX_VAL(x)	((0x1f & (x)) << 16)
263 /* COMINIT GAP width window */
264 #define RG_T2_MAX_MSK		GENMASK(13, 8)
265 #define RG_T2_MAX_VAL(x)	((0x3f & (x)) << 8)
266 /* COMWAK GAP width window */
267 #define RG_TG_MIN_MSK		GENMASK(7, 5)
268 #define RG_TG_MIN_VAL(x)	((0x7 & (x)) << 5)
269 /* COMINIT GAP width window */
270 #define RG_T2_MIN_MSK		GENMASK(4, 0)
271 #define RG_T2_MIN_VAL(x)	(0x1f & (x))
272 
273 #define ANA_RG_CTRL_SIGNAL1		0x4c
274 /* TX driver tail current control for 0dB de-empahsis mdoe for Gen1 speed */
275 #define RG_IDRV_0DB_GEN1_MSK		GENMASK(13, 8)
276 #define RG_IDRV_0DB_GEN1_VAL(x)		((0x3f & (x)) << 8)
277 
278 #define ANA_RG_CTRL_SIGNAL4		0x58
279 #define RG_CDR_BICLTR_GEN1_MSK		GENMASK(23, 20)
280 #define RG_CDR_BICLTR_GEN1_VAL(x)	((0xf & (x)) << 20)
281 /* Loop filter R1 resistance adjustment for Gen1 speed */
282 #define RG_CDR_BR_GEN2_MSK		GENMASK(10, 8)
283 #define RG_CDR_BR_GEN2_VAL(x)		((0x7 & (x)) << 8)
284 
285 #define ANA_RG_CTRL_SIGNAL6		0x60
286 /* I-path capacitance adjustment for Gen1 */
287 #define RG_CDR_BC_GEN1_MSK		GENMASK(28, 24)
288 #define RG_CDR_BC_GEN1_VAL(x)		((0x1f & (x)) << 24)
289 #define RG_CDR_BIRLTR_GEN1_MSK		GENMASK(4, 0)
290 #define RG_CDR_BIRLTR_GEN1_VAL(x)	(0x1f & (x))
291 
292 #define ANA_EQ_EYE_CTRL_SIGNAL1		0x6c
293 /* RX Gen1 LEQ tuning step */
294 #define RG_EQ_DLEQ_LFI_GEN1_MSK		GENMASK(11, 8)
295 #define RG_EQ_DLEQ_LFI_GEN1_VAL(x)	((0xf & (x)) << 8)
296 
297 #define ANA_EQ_EYE_CTRL_SIGNAL4		0xd8
298 #define RG_CDR_BIRLTD0_GEN1_MSK		GENMASK(20, 16)
299 #define RG_CDR_BIRLTD0_GEN1_VAL(x)	((0x1f & (x)) << 16)
300 
301 #define ANA_EQ_EYE_CTRL_SIGNAL5		0xdc
302 #define RG_CDR_BIRLTD0_GEN3_MSK		GENMASK(4, 0)
303 #define RG_CDR_BIRLTD0_GEN3_VAL(x)	(0x1f & (x))
304 
305 /* PHY switch between pcie/usb3/sgmii/sata */
306 #define USB_PHY_SWITCH_CTRL	0x0
307 #define RG_PHY_SW_TYPE		GENMASK(3, 0)
308 #define RG_PHY_SW_PCIE		0x0
309 #define RG_PHY_SW_USB3		0x1
310 #define RG_PHY_SW_SGMII		0x2
311 #define RG_PHY_SW_SATA		0x3
312 
313 #define TPHY_CLKS_CNT	2
314 
315 enum mtk_phy_version {
316 	MTK_PHY_V1 = 1,
317 	MTK_PHY_V2,
318 	MTK_PHY_V3,
319 };
320 
321 struct mtk_phy_pdata {
322 	/* avoid RX sensitivity level degradation only for mt8173 */
323 	bool avoid_rx_sen_degradation;
324 	/*
325 	 * workaround only for mt8195, HW fix it for others of V3,
326 	 * u2phy should use integer mode instead of fractional mode of
327 	 * 48M PLL, fix it by switching PLL to 26M from default 48M
328 	 */
329 	bool sw_pll_48m_to_26m;
330 	/*
331 	 * Some SoCs (e.g. mt8195) drop a bit when use auto load efuse,
332 	 * support sw way, also support it for v2/v3 optionally.
333 	 */
334 	bool sw_efuse_supported;
335 	enum mtk_phy_version version;
336 };
337 
338 struct u2phy_banks {
339 	void __iomem *misc;
340 	void __iomem *fmreg;
341 	void __iomem *com;
342 };
343 
344 struct u3phy_banks {
345 	void __iomem *spllc;
346 	void __iomem *chip;
347 	void __iomem *phyd; /* include u3phyd_bank2 */
348 	void __iomem *phya; /* include u3phya_da */
349 };
350 
351 struct mtk_phy_instance {
352 	struct phy *phy;
353 	void __iomem *port_base;
354 	union {
355 		struct u2phy_banks u2_banks;
356 		struct u3phy_banks u3_banks;
357 	};
358 	struct clk_bulk_data clks[TPHY_CLKS_CNT];
359 	u32 index;
360 	u32 type;
361 	struct regmap *type_sw;
362 	u32 type_sw_reg;
363 	u32 type_sw_index;
364 	u32 efuse_sw_en;
365 	u32 efuse_intr;
366 	u32 efuse_tx_imp;
367 	u32 efuse_rx_imp;
368 	int eye_src;
369 	int eye_vrt;
370 	int eye_term;
371 	int intr;
372 	int discth;
373 	bool bc12_en;
374 };
375 
376 struct mtk_tphy {
377 	struct device *dev;
378 	void __iomem *sif_base;	/* only shared sif */
379 	const struct mtk_phy_pdata *pdata;
380 	struct mtk_phy_instance **phys;
381 	int nphys;
382 	int src_ref_clk; /* MHZ, reference clock for slew rate calibrate */
383 	int src_coef; /* coefficient for slew rate calibrate */
384 };
385 
386 static void hs_slew_rate_calibrate(struct mtk_tphy *tphy,
387 	struct mtk_phy_instance *instance)
388 {
389 	struct u2phy_banks *u2_banks = &instance->u2_banks;
390 	void __iomem *fmreg = u2_banks->fmreg;
391 	void __iomem *com = u2_banks->com;
392 	int calibration_val;
393 	int fm_out;
394 	u32 tmp;
395 
396 	/* HW V3 doesn't support slew rate cal anymore */
397 	if (tphy->pdata->version == MTK_PHY_V3)
398 		return;
399 
400 	/* use force value */
401 	if (instance->eye_src)
402 		return;
403 
404 	/* enable USB ring oscillator */
405 	mtk_phy_set_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCAL_EN);
406 	udelay(1);
407 
408 	/*enable free run clock */
409 	mtk_phy_set_bits(fmreg + U3P_U2FREQ_FMMONR1, P2F_RG_FRCK_EN);
410 
411 	/* set cycle count as 1024, and select u2 channel */
412 	tmp = readl(fmreg + U3P_U2FREQ_FMCR0);
413 	tmp &= ~(P2F_RG_CYCLECNT | P2F_RG_MONCLK_SEL);
414 	tmp |= P2F_RG_CYCLECNT_VAL(U3P_FM_DET_CYCLE_CNT);
415 	if (tphy->pdata->version == MTK_PHY_V1)
416 		tmp |= P2F_RG_MONCLK_SEL_VAL(instance->index >> 1);
417 
418 	writel(tmp, fmreg + U3P_U2FREQ_FMCR0);
419 
420 	/* enable frequency meter */
421 	mtk_phy_set_bits(fmreg + U3P_U2FREQ_FMCR0, P2F_RG_FREQDET_EN);
422 
423 	/* ignore return value */
424 	readl_poll_timeout(fmreg + U3P_U2FREQ_FMMONR1, tmp,
425 			   (tmp & P2F_USB_FM_VALID), 10, 200);
426 
427 	fm_out = readl(fmreg + U3P_U2FREQ_VALUE);
428 
429 	/* disable frequency meter */
430 	mtk_phy_clear_bits(fmreg + U3P_U2FREQ_FMCR0, P2F_RG_FREQDET_EN);
431 
432 	/*disable free run clock */
433 	mtk_phy_clear_bits(fmreg + U3P_U2FREQ_FMMONR1, P2F_RG_FRCK_EN);
434 
435 	if (fm_out) {
436 		/* ( 1024 / FM_OUT ) x reference clock frequency x coef */
437 		tmp = tphy->src_ref_clk * tphy->src_coef;
438 		tmp = (tmp * U3P_FM_DET_CYCLE_CNT) / fm_out;
439 		calibration_val = DIV_ROUND_CLOSEST(tmp, U3P_SR_COEF_DIVISOR);
440 	} else {
441 		/* if FM detection fail, set default value */
442 		calibration_val = 4;
443 	}
444 	dev_dbg(tphy->dev, "phy:%d, fm_out:%d, calib:%d (clk:%d, coef:%d)\n",
445 		instance->index, fm_out, calibration_val,
446 		tphy->src_ref_clk, tphy->src_coef);
447 
448 	/* set HS slew rate */
449 	mtk_phy_update_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCTRL,
450 			    PA5_RG_U2_HSTX_SRCTRL_VAL(calibration_val));
451 
452 	/* disable USB ring oscillator */
453 	mtk_phy_clear_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCAL_EN);
454 }
455 
456 static void u3_phy_instance_init(struct mtk_tphy *tphy,
457 	struct mtk_phy_instance *instance)
458 {
459 	struct u3phy_banks *u3_banks = &instance->u3_banks;
460 
461 	/* gating PCIe Analog XTAL clock */
462 	mtk_phy_set_bits(u3_banks->spllc + U3P_SPLLC_XTALCTL3,
463 			 XC3_RG_U3_XTAL_RX_PWD | XC3_RG_U3_FRC_XTAL_RX_PWD);
464 
465 	/* gating XSQ */
466 	mtk_phy_update_bits(u3_banks->phya + U3P_U3_PHYA_DA_REG0,
467 			    P3A_RG_XTAL_EXT_EN_U3, P3A_RG_XTAL_EXT_EN_U3_VAL(2));
468 
469 	mtk_phy_update_bits(u3_banks->phya + U3P_U3_PHYA_REG9,
470 			    P3A_RG_RX_DAC_MUX, P3A_RG_RX_DAC_MUX_VAL(4));
471 
472 	mtk_phy_update_bits(u3_banks->phya + U3P_U3_PHYA_REG6,
473 			    P3A_RG_TX_EIDLE_CM, P3A_RG_TX_EIDLE_CM_VAL(0xe));
474 
475 	mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_CDR1,
476 			    P3D_RG_CDR_BIR_LTD0 | P3D_RG_CDR_BIR_LTD1,
477 			    P3D_RG_CDR_BIR_LTD0_VAL(0xc) | P3D_RG_CDR_BIR_LTD1_VAL(0x3));
478 
479 	mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_LFPS1,
480 			    P3D_RG_FWAKE_TH, P3D_RG_FWAKE_TH_VAL(0x34));
481 
482 	mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_RXDET1,
483 			    P3D_RG_RXDET_STB2_SET, P3D_RG_RXDET_STB2_SET_VAL(0x10));
484 
485 	mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_RXDET2,
486 			    P3D_RG_RXDET_STB2_SET_P3, P3D_RG_RXDET_STB2_SET_P3_VAL(0x10));
487 
488 	dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
489 }
490 
491 static void u2_phy_pll_26m_set(struct mtk_tphy *tphy,
492 	struct mtk_phy_instance *instance)
493 {
494 	struct u2phy_banks *u2_banks = &instance->u2_banks;
495 	void __iomem *com = u2_banks->com;
496 
497 	if (!tphy->pdata->sw_pll_48m_to_26m)
498 		return;
499 
500 	mtk_phy_update_bits(com + U3P_USBPHYACR0, PA0_USB20_PLL_PREDIV,
501 			    PA0_USB20_PLL_PREDIV_VAL(0));
502 
503 	mtk_phy_update_bits(com + U3P_USBPHYACR2, PA2_RG_U2PLL_BW,
504 			    PA2_RG_U2PLL_BW_VAL(3));
505 
506 	writel(P2R_RG_U2PLL_FBDIV_26M, com + U3P_U2PHYA_RESV);
507 
508 	mtk_phy_set_bits(com + U3P_U2PHYA_RESV1,
509 			 P2R_RG_U2PLL_FRA_EN | P2R_RG_U2PLL_REFCLK_SEL);
510 }
511 
512 static void u2_phy_instance_init(struct mtk_tphy *tphy,
513 	struct mtk_phy_instance *instance)
514 {
515 	struct u2phy_banks *u2_banks = &instance->u2_banks;
516 	void __iomem *com = u2_banks->com;
517 	u32 index = instance->index;
518 
519 	/* switch to USB function, and enable usb pll */
520 	mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_FORCE_UART_EN | P2C_FORCE_SUSPENDM);
521 
522 	mtk_phy_update_bits(com + U3P_U2PHYDTM0, P2C_RG_XCVRSEL | P2C_RG_DATAIN,
523 			    P2C_RG_XCVRSEL_VAL(1) | P2C_RG_DATAIN_VAL(0));
524 
525 	mtk_phy_clear_bits(com + U3P_U2PHYDTM1, P2C_RG_UART_EN);
526 
527 	mtk_phy_set_bits(com + U3P_USBPHYACR0, PA0_RG_USB20_INTR_EN);
528 
529 	/* disable switch 100uA current to SSUSB */
530 	mtk_phy_clear_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HS_100U_U3_EN);
531 
532 	if (!index)
533 		mtk_phy_clear_bits(com + U3P_U2PHYACR4, P2C_U2_GPIO_CTR_MSK);
534 
535 	if (tphy->pdata->avoid_rx_sen_degradation) {
536 		if (!index) {
537 			mtk_phy_set_bits(com + U3P_USBPHYACR2, PA2_RG_SIF_U2PLL_FORCE_EN);
538 
539 			mtk_phy_clear_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);
540 		} else {
541 			mtk_phy_set_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);
542 
543 			mtk_phy_set_bits(com + U3P_U2PHYDTM0,
544 					 P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM);
545 		}
546 	}
547 
548 	/* DP/DM BC1.1 path Disable */
549 	mtk_phy_clear_bits(com + U3P_USBPHYACR6, PA6_RG_U2_BC11_SW_EN);
550 
551 	mtk_phy_update_bits(com + U3P_USBPHYACR6, PA6_RG_U2_SQTH, PA6_RG_U2_SQTH_VAL(2));
552 
553 	/* Workaround only for mt8195, HW fix it for others (V3) */
554 	u2_phy_pll_26m_set(tphy, instance);
555 
556 	dev_dbg(tphy->dev, "%s(%d)\n", __func__, index);
557 }
558 
559 static void u2_phy_instance_power_on(struct mtk_tphy *tphy,
560 	struct mtk_phy_instance *instance)
561 {
562 	struct u2phy_banks *u2_banks = &instance->u2_banks;
563 	void __iomem *com = u2_banks->com;
564 	u32 index = instance->index;
565 
566 	mtk_phy_clear_bits(com + U3P_U2PHYDTM0,
567 			   P2C_RG_XCVRSEL | P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
568 
569 	/* OTG Enable */
570 	mtk_phy_set_bits(com + U3P_USBPHYACR6, PA6_RG_U2_OTG_VBUSCMP_EN);
571 
572 	mtk_phy_set_bits(com + U3P_U2PHYDTM1, P2C_RG_VBUSVALID | P2C_RG_AVALID);
573 
574 	mtk_phy_clear_bits(com + U3P_U2PHYDTM1, P2C_RG_SESSEND);
575 
576 	if (tphy->pdata->avoid_rx_sen_degradation && index) {
577 		mtk_phy_set_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);
578 
579 		mtk_phy_set_bits(com + U3P_U2PHYDTM0, P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM);
580 	}
581 	dev_dbg(tphy->dev, "%s(%d)\n", __func__, index);
582 }
583 
584 static void u2_phy_instance_power_off(struct mtk_tphy *tphy,
585 	struct mtk_phy_instance *instance)
586 {
587 	struct u2phy_banks *u2_banks = &instance->u2_banks;
588 	void __iomem *com = u2_banks->com;
589 	u32 index = instance->index;
590 
591 	mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_RG_XCVRSEL | P2C_RG_DATAIN);
592 
593 	/* OTG Disable */
594 	mtk_phy_clear_bits(com + U3P_USBPHYACR6, PA6_RG_U2_OTG_VBUSCMP_EN);
595 
596 	mtk_phy_clear_bits(com + U3P_U2PHYDTM1, P2C_RG_VBUSVALID | P2C_RG_AVALID);
597 
598 	mtk_phy_set_bits(com + U3P_U2PHYDTM1, P2C_RG_SESSEND);
599 
600 	if (tphy->pdata->avoid_rx_sen_degradation && index) {
601 		mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_RG_SUSPENDM | P2C_FORCE_SUSPENDM);
602 
603 		mtk_phy_clear_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);
604 	}
605 
606 	dev_dbg(tphy->dev, "%s(%d)\n", __func__, index);
607 }
608 
609 static void u2_phy_instance_exit(struct mtk_tphy *tphy,
610 	struct mtk_phy_instance *instance)
611 {
612 	struct u2phy_banks *u2_banks = &instance->u2_banks;
613 	void __iomem *com = u2_banks->com;
614 	u32 index = instance->index;
615 
616 	if (tphy->pdata->avoid_rx_sen_degradation && index) {
617 		mtk_phy_clear_bits(com + U3D_U2PHYDCR0, P2C_RG_SIF_U2PLL_FORCE_ON);
618 
619 		mtk_phy_clear_bits(com + U3P_U2PHYDTM0, P2C_FORCE_SUSPENDM);
620 	}
621 }
622 
623 static void u2_phy_instance_set_mode(struct mtk_tphy *tphy,
624 				     struct mtk_phy_instance *instance,
625 				     enum phy_mode mode)
626 {
627 	struct u2phy_banks *u2_banks = &instance->u2_banks;
628 	u32 tmp;
629 
630 	tmp = readl(u2_banks->com + U3P_U2PHYDTM1);
631 	switch (mode) {
632 	case PHY_MODE_USB_DEVICE:
633 		tmp |= P2C_FORCE_IDDIG | P2C_RG_IDDIG;
634 		break;
635 	case PHY_MODE_USB_HOST:
636 		tmp |= P2C_FORCE_IDDIG;
637 		tmp &= ~P2C_RG_IDDIG;
638 		break;
639 	case PHY_MODE_USB_OTG:
640 		tmp &= ~(P2C_FORCE_IDDIG | P2C_RG_IDDIG);
641 		break;
642 	default:
643 		return;
644 	}
645 	writel(tmp, u2_banks->com + U3P_U2PHYDTM1);
646 }
647 
648 static void pcie_phy_instance_init(struct mtk_tphy *tphy,
649 	struct mtk_phy_instance *instance)
650 {
651 	struct u3phy_banks *u3_banks = &instance->u3_banks;
652 	void __iomem *phya = u3_banks->phya;
653 
654 	if (tphy->pdata->version != MTK_PHY_V1)
655 		return;
656 
657 	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG0,
658 			    P3A_RG_XTAL_EXT_PE1H | P3A_RG_XTAL_EXT_PE2H,
659 			    P3A_RG_XTAL_EXT_PE1H_VAL(0x2) | P3A_RG_XTAL_EXT_PE2H_VAL(0x2));
660 
661 	/* ref clk drive */
662 	mtk_phy_update_bits(phya + U3P_U3_PHYA_REG1, P3A_RG_CLKDRV_AMP,
663 			    P3A_RG_CLKDRV_AMP_VAL(0x4));
664 
665 	mtk_phy_update_bits(phya + U3P_U3_PHYA_REG0, P3A_RG_CLKDRV_OFF,
666 			    P3A_RG_CLKDRV_OFF_VAL(0x1));
667 
668 	/* SSC delta -5000ppm */
669 	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG20, P3A_RG_PLL_DELTA1_PE2H,
670 			    P3A_RG_PLL_DELTA1_PE2H_VAL(0x3c));
671 
672 	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG25, P3A_RG_PLL_DELTA_PE2H,
673 			    P3A_RG_PLL_DELTA_PE2H_VAL(0x36));
674 
675 	/* change pll BW 0.6M */
676 	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG5,
677 			    P3A_RG_PLL_BR_PE2H | P3A_RG_PLL_IC_PE2H,
678 			    P3A_RG_PLL_BR_PE2H_VAL(0x1) | P3A_RG_PLL_IC_PE2H_VAL(0x1));
679 
680 	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG4,
681 			    P3A_RG_PLL_DIVEN_PE2H | P3A_RG_PLL_BC_PE2H,
682 			    P3A_RG_PLL_BC_PE2H_VAL(0x3));
683 
684 	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG6, P3A_RG_PLL_IR_PE2H,
685 			    P3A_RG_PLL_IR_PE2H_VAL(0x2));
686 
687 	mtk_phy_update_bits(phya + U3P_U3_PHYA_DA_REG7, P3A_RG_PLL_BP_PE2H,
688 			    P3A_RG_PLL_BP_PE2H_VAL(0xa));
689 
690 	/* Tx Detect Rx Timing: 10us -> 5us */
691 	mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_RXDET1,
692 			    P3D_RG_RXDET_STB2_SET, P3D_RG_RXDET_STB2_SET_VAL(0x10));
693 
694 	mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_RXDET2,
695 			    P3D_RG_RXDET_STB2_SET_P3, P3D_RG_RXDET_STB2_SET_P3_VAL(0x10));
696 
697 	/* wait for PCIe subsys register to active */
698 	usleep_range(2500, 3000);
699 	dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
700 }
701 
702 static void pcie_phy_instance_power_on(struct mtk_tphy *tphy,
703 	struct mtk_phy_instance *instance)
704 {
705 	struct u3phy_banks *bank = &instance->u3_banks;
706 
707 	mtk_phy_clear_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLD,
708 			   P3C_FORCE_IP_SW_RST | P3C_REG_IP_SW_RST);
709 
710 	mtk_phy_clear_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLE,
711 			   P3C_RG_SWRST_U3_PHYD_FORCE_EN | P3C_RG_SWRST_U3_PHYD);
712 }
713 
714 static void pcie_phy_instance_power_off(struct mtk_tphy *tphy,
715 	struct mtk_phy_instance *instance)
716 
717 {
718 	struct u3phy_banks *bank = &instance->u3_banks;
719 
720 	mtk_phy_set_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLD,
721 			 P3C_FORCE_IP_SW_RST | P3C_REG_IP_SW_RST);
722 
723 	mtk_phy_set_bits(bank->chip + U3P_U3_CHIP_GPIO_CTLE,
724 			 P3C_RG_SWRST_U3_PHYD_FORCE_EN | P3C_RG_SWRST_U3_PHYD);
725 }
726 
727 static void sata_phy_instance_init(struct mtk_tphy *tphy,
728 	struct mtk_phy_instance *instance)
729 {
730 	struct u3phy_banks *u3_banks = &instance->u3_banks;
731 	void __iomem *phyd = u3_banks->phyd;
732 
733 	/* charge current adjustment */
734 	mtk_phy_update_bits(phyd + ANA_RG_CTRL_SIGNAL6,
735 			    RG_CDR_BIRLTR_GEN1_MSK | RG_CDR_BC_GEN1_MSK,
736 			    RG_CDR_BIRLTR_GEN1_VAL(0x6) | RG_CDR_BC_GEN1_VAL(0x1a));
737 
738 	mtk_phy_update_bits(phyd + ANA_EQ_EYE_CTRL_SIGNAL4, RG_CDR_BIRLTD0_GEN1_MSK,
739 			    RG_CDR_BIRLTD0_GEN1_VAL(0x18));
740 
741 	mtk_phy_update_bits(phyd + ANA_EQ_EYE_CTRL_SIGNAL5, RG_CDR_BIRLTD0_GEN3_MSK,
742 			    RG_CDR_BIRLTD0_GEN3_VAL(0x06));
743 
744 	mtk_phy_update_bits(phyd + ANA_RG_CTRL_SIGNAL4,
745 			    RG_CDR_BICLTR_GEN1_MSK | RG_CDR_BR_GEN2_MSK,
746 			    RG_CDR_BICLTR_GEN1_VAL(0x0c) | RG_CDR_BR_GEN2_VAL(0x07));
747 
748 	mtk_phy_update_bits(phyd + PHYD_CTRL_SIGNAL_MODE4,
749 			    RG_CDR_BICLTD0_GEN1_MSK | RG_CDR_BICLTD1_GEN1_MSK,
750 			    RG_CDR_BICLTD0_GEN1_VAL(0x08) | RG_CDR_BICLTD1_GEN1_VAL(0x02));
751 
752 	mtk_phy_update_bits(phyd + PHYD_DESIGN_OPTION2, RG_LOCK_CNT_SEL_MSK,
753 			    RG_LOCK_CNT_SEL_VAL(0x02));
754 
755 	mtk_phy_update_bits(phyd + PHYD_DESIGN_OPTION9,
756 			    RG_T2_MIN_MSK | RG_TG_MIN_MSK,
757 			    RG_T2_MIN_VAL(0x12) | RG_TG_MIN_VAL(0x04));
758 
759 	mtk_phy_update_bits(phyd + PHYD_DESIGN_OPTION9,
760 			    RG_T2_MAX_MSK | RG_TG_MAX_MSK,
761 			    RG_T2_MAX_VAL(0x31) | RG_TG_MAX_VAL(0x0e));
762 
763 	mtk_phy_update_bits(phyd + ANA_RG_CTRL_SIGNAL1, RG_IDRV_0DB_GEN1_MSK,
764 			    RG_IDRV_0DB_GEN1_VAL(0x20));
765 
766 	mtk_phy_update_bits(phyd + ANA_EQ_EYE_CTRL_SIGNAL1, RG_EQ_DLEQ_LFI_GEN1_MSK,
767 			    RG_EQ_DLEQ_LFI_GEN1_VAL(0x03));
768 
769 	dev_dbg(tphy->dev, "%s(%d)\n", __func__, instance->index);
770 }
771 
772 static void phy_v1_banks_init(struct mtk_tphy *tphy,
773 			      struct mtk_phy_instance *instance)
774 {
775 	struct u2phy_banks *u2_banks = &instance->u2_banks;
776 	struct u3phy_banks *u3_banks = &instance->u3_banks;
777 
778 	switch (instance->type) {
779 	case PHY_TYPE_USB2:
780 		u2_banks->misc = NULL;
781 		u2_banks->fmreg = tphy->sif_base + SSUSB_SIFSLV_V1_U2FREQ;
782 		u2_banks->com = instance->port_base + SSUSB_SIFSLV_V1_U2PHY_COM;
783 		break;
784 	case PHY_TYPE_USB3:
785 	case PHY_TYPE_PCIE:
786 		u3_banks->spllc = tphy->sif_base + SSUSB_SIFSLV_V1_SPLLC;
787 		u3_banks->chip = tphy->sif_base + SSUSB_SIFSLV_V1_CHIP;
788 		u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V1_U3PHYD;
789 		u3_banks->phya = instance->port_base + SSUSB_SIFSLV_V1_U3PHYA;
790 		break;
791 	case PHY_TYPE_SATA:
792 		u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V1_U3PHYD;
793 		break;
794 	default:
795 		dev_err(tphy->dev, "incompatible PHY type\n");
796 		return;
797 	}
798 }
799 
800 static void phy_v2_banks_init(struct mtk_tphy *tphy,
801 			      struct mtk_phy_instance *instance)
802 {
803 	struct u2phy_banks *u2_banks = &instance->u2_banks;
804 	struct u3phy_banks *u3_banks = &instance->u3_banks;
805 
806 	switch (instance->type) {
807 	case PHY_TYPE_USB2:
808 		u2_banks->misc = instance->port_base + SSUSB_SIFSLV_V2_MISC;
809 		u2_banks->fmreg = instance->port_base + SSUSB_SIFSLV_V2_U2FREQ;
810 		u2_banks->com = instance->port_base + SSUSB_SIFSLV_V2_U2PHY_COM;
811 		break;
812 	case PHY_TYPE_USB3:
813 	case PHY_TYPE_PCIE:
814 		u3_banks->spllc = instance->port_base + SSUSB_SIFSLV_V2_SPLLC;
815 		u3_banks->chip = instance->port_base + SSUSB_SIFSLV_V2_CHIP;
816 		u3_banks->phyd = instance->port_base + SSUSB_SIFSLV_V2_U3PHYD;
817 		u3_banks->phya = instance->port_base + SSUSB_SIFSLV_V2_U3PHYA;
818 		break;
819 	default:
820 		dev_err(tphy->dev, "incompatible PHY type\n");
821 		return;
822 	}
823 }
824 
825 static void phy_parse_property(struct mtk_tphy *tphy,
826 				struct mtk_phy_instance *instance)
827 {
828 	struct device *dev = &instance->phy->dev;
829 
830 	if (instance->type != PHY_TYPE_USB2)
831 		return;
832 
833 	instance->bc12_en = device_property_read_bool(dev, "mediatek,bc12");
834 	device_property_read_u32(dev, "mediatek,eye-src",
835 				 &instance->eye_src);
836 	device_property_read_u32(dev, "mediatek,eye-vrt",
837 				 &instance->eye_vrt);
838 	device_property_read_u32(dev, "mediatek,eye-term",
839 				 &instance->eye_term);
840 	device_property_read_u32(dev, "mediatek,intr",
841 				 &instance->intr);
842 	device_property_read_u32(dev, "mediatek,discth",
843 				 &instance->discth);
844 	dev_dbg(dev, "bc12:%d, src:%d, vrt:%d, term:%d, intr:%d, disc:%d\n",
845 		instance->bc12_en, instance->eye_src,
846 		instance->eye_vrt, instance->eye_term,
847 		instance->intr, instance->discth);
848 }
849 
850 static void u2_phy_props_set(struct mtk_tphy *tphy,
851 			     struct mtk_phy_instance *instance)
852 {
853 	struct u2phy_banks *u2_banks = &instance->u2_banks;
854 	void __iomem *com = u2_banks->com;
855 
856 	if (instance->bc12_en) /* BC1.2 path Enable */
857 		mtk_phy_set_bits(com + U3P_U2PHYBC12C, P2C_RG_CHGDT_EN);
858 
859 	if (tphy->pdata->version < MTK_PHY_V3 && instance->eye_src)
860 		mtk_phy_update_bits(com + U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCTRL,
861 				    PA5_RG_U2_HSTX_SRCTRL_VAL(instance->eye_src));
862 
863 	if (instance->eye_vrt)
864 		mtk_phy_update_bits(com + U3P_USBPHYACR1, PA1_RG_VRT_SEL,
865 				    PA1_RG_VRT_SEL_VAL(instance->eye_vrt));
866 
867 	if (instance->eye_term)
868 		mtk_phy_update_bits(com + U3P_USBPHYACR1, PA1_RG_TERM_SEL,
869 				    PA1_RG_TERM_SEL_VAL(instance->eye_term));
870 
871 	if (instance->intr)
872 		mtk_phy_update_bits(com + U3P_USBPHYACR1, PA1_RG_INTR_CAL,
873 				    PA1_RG_INTR_CAL_VAL(instance->intr));
874 
875 	if (instance->discth)
876 		mtk_phy_update_bits(com + U3P_USBPHYACR6, PA6_RG_U2_DISCTH,
877 				    PA6_RG_U2_DISCTH_VAL(instance->discth));
878 }
879 
880 /* type switch for usb3/pcie/sgmii/sata */
881 static int phy_type_syscon_get(struct mtk_phy_instance *instance,
882 			       struct device_node *dn)
883 {
884 	struct of_phandle_args args;
885 	int ret;
886 
887 	/* type switch function is optional */
888 	if (!of_property_read_bool(dn, "mediatek,syscon-type"))
889 		return 0;
890 
891 	ret = of_parse_phandle_with_fixed_args(dn, "mediatek,syscon-type",
892 					       2, 0, &args);
893 	if (ret)
894 		return ret;
895 
896 	instance->type_sw_reg = args.args[0];
897 	instance->type_sw_index = args.args[1] & 0x3; /* <=3 */
898 	instance->type_sw = syscon_node_to_regmap(args.np);
899 	of_node_put(args.np);
900 	dev_info(&instance->phy->dev, "type_sw - reg %#x, index %d\n",
901 		 instance->type_sw_reg, instance->type_sw_index);
902 
903 	return PTR_ERR_OR_ZERO(instance->type_sw);
904 }
905 
906 static int phy_type_set(struct mtk_phy_instance *instance)
907 {
908 	int type;
909 	u32 mask;
910 
911 	if (!instance->type_sw)
912 		return 0;
913 
914 	switch (instance->type) {
915 	case PHY_TYPE_USB3:
916 		type = RG_PHY_SW_USB3;
917 		break;
918 	case PHY_TYPE_PCIE:
919 		type = RG_PHY_SW_PCIE;
920 		break;
921 	case PHY_TYPE_SGMII:
922 		type = RG_PHY_SW_SGMII;
923 		break;
924 	case PHY_TYPE_SATA:
925 		type = RG_PHY_SW_SATA;
926 		break;
927 	case PHY_TYPE_USB2:
928 	default:
929 		return 0;
930 	}
931 
932 	mask = RG_PHY_SW_TYPE << (instance->type_sw_index * BITS_PER_BYTE);
933 	regmap_update_bits(instance->type_sw, instance->type_sw_reg, mask, type);
934 
935 	return 0;
936 }
937 
938 static int phy_efuse_get(struct mtk_tphy *tphy, struct mtk_phy_instance *instance)
939 {
940 	struct device *dev = &instance->phy->dev;
941 	int ret = 0;
942 
943 	/* tphy v1 doesn't support sw efuse, skip it */
944 	if (!tphy->pdata->sw_efuse_supported) {
945 		instance->efuse_sw_en = 0;
946 		return 0;
947 	}
948 
949 	/* software efuse is optional */
950 	instance->efuse_sw_en = device_property_read_bool(dev, "nvmem-cells");
951 	if (!instance->efuse_sw_en)
952 		return 0;
953 
954 	switch (instance->type) {
955 	case PHY_TYPE_USB2:
956 		ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr);
957 		if (ret) {
958 			dev_err(dev, "fail to get u2 intr efuse, %d\n", ret);
959 			break;
960 		}
961 
962 		/* no efuse, ignore it */
963 		if (!instance->efuse_intr) {
964 			dev_warn(dev, "no u2 intr efuse, but dts enable it\n");
965 			instance->efuse_sw_en = 0;
966 			break;
967 		}
968 
969 		dev_dbg(dev, "u2 efuse - intr %x\n", instance->efuse_intr);
970 		break;
971 
972 	case PHY_TYPE_USB3:
973 	case PHY_TYPE_PCIE:
974 		ret = nvmem_cell_read_variable_le_u32(dev, "intr", &instance->efuse_intr);
975 		if (ret) {
976 			dev_err(dev, "fail to get u3 intr efuse, %d\n", ret);
977 			break;
978 		}
979 
980 		ret = nvmem_cell_read_variable_le_u32(dev, "rx_imp", &instance->efuse_rx_imp);
981 		if (ret) {
982 			dev_err(dev, "fail to get u3 rx_imp efuse, %d\n", ret);
983 			break;
984 		}
985 
986 		ret = nvmem_cell_read_variable_le_u32(dev, "tx_imp", &instance->efuse_tx_imp);
987 		if (ret) {
988 			dev_err(dev, "fail to get u3 tx_imp efuse, %d\n", ret);
989 			break;
990 		}
991 
992 		/* no efuse, ignore it */
993 		if (!instance->efuse_intr &&
994 		    !instance->efuse_rx_imp &&
995 		    !instance->efuse_tx_imp) {
996 			dev_warn(dev, "no u3 intr efuse, but dts enable it\n");
997 			instance->efuse_sw_en = 0;
998 			break;
999 		}
1000 
1001 		dev_dbg(dev, "u3 efuse - intr %x, rx_imp %x, tx_imp %x\n",
1002 			instance->efuse_intr, instance->efuse_rx_imp,instance->efuse_tx_imp);
1003 		break;
1004 	default:
1005 		dev_err(dev, "no sw efuse for type %d\n", instance->type);
1006 		ret = -EINVAL;
1007 	}
1008 
1009 	return ret;
1010 }
1011 
1012 static void phy_efuse_set(struct mtk_phy_instance *instance)
1013 {
1014 	struct device *dev = &instance->phy->dev;
1015 	struct u2phy_banks *u2_banks = &instance->u2_banks;
1016 	struct u3phy_banks *u3_banks = &instance->u3_banks;
1017 
1018 	if (!instance->efuse_sw_en)
1019 		return;
1020 
1021 	switch (instance->type) {
1022 	case PHY_TYPE_USB2:
1023 		mtk_phy_set_bits(u2_banks->misc + U3P_MISC_REG1, MR1_EFUSE_AUTO_LOAD_DIS);
1024 
1025 		mtk_phy_update_bits(u2_banks->com + U3P_USBPHYACR1, PA1_RG_INTR_CAL,
1026 				    PA1_RG_INTR_CAL_VAL(instance->efuse_intr));
1027 		break;
1028 	case PHY_TYPE_USB3:
1029 	case PHY_TYPE_PCIE:
1030 		mtk_phy_set_bits(u3_banks->phyd + U3P_U3_PHYD_RSV, P3D_RG_EFUSE_AUTO_LOAD_DIS);
1031 
1032 		mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0, P3D_RG_TX_IMPEL,
1033 				    P3D_RG_TX_IMPEL_VAL(instance->efuse_tx_imp));
1034 		mtk_phy_set_bits(u3_banks->phyd + U3P_U3_PHYD_IMPCAL0, P3D_RG_FORCE_TX_IMPEL);
1035 
1036 		mtk_phy_update_bits(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1, P3D_RG_RX_IMPEL,
1037 				    P3D_RG_RX_IMPEL_VAL(instance->efuse_rx_imp));
1038 		mtk_phy_set_bits(u3_banks->phyd + U3P_U3_PHYD_IMPCAL1, P3D_RG_FORCE_RX_IMPEL);
1039 
1040 		mtk_phy_update_bits(u3_banks->phya + U3P_U3_PHYA_REG0, P3A_RG_IEXT_INTR,
1041 				    P3A_RG_IEXT_INTR_VAL(instance->efuse_intr));
1042 		break;
1043 	default:
1044 		dev_warn(dev, "no sw efuse for type %d\n", instance->type);
1045 		break;
1046 	}
1047 }
1048 
1049 static int mtk_phy_init(struct phy *phy)
1050 {
1051 	struct mtk_phy_instance *instance = phy_get_drvdata(phy);
1052 	struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);
1053 	int ret;
1054 
1055 	ret = clk_bulk_prepare_enable(TPHY_CLKS_CNT, instance->clks);
1056 	if (ret)
1057 		return ret;
1058 
1059 	phy_efuse_set(instance);
1060 
1061 	switch (instance->type) {
1062 	case PHY_TYPE_USB2:
1063 		u2_phy_instance_init(tphy, instance);
1064 		u2_phy_props_set(tphy, instance);
1065 		break;
1066 	case PHY_TYPE_USB3:
1067 		u3_phy_instance_init(tphy, instance);
1068 		break;
1069 	case PHY_TYPE_PCIE:
1070 		pcie_phy_instance_init(tphy, instance);
1071 		break;
1072 	case PHY_TYPE_SATA:
1073 		sata_phy_instance_init(tphy, instance);
1074 		break;
1075 	case PHY_TYPE_SGMII:
1076 		/* nothing to do, only used to set type */
1077 		break;
1078 	default:
1079 		dev_err(tphy->dev, "incompatible PHY type\n");
1080 		clk_bulk_disable_unprepare(TPHY_CLKS_CNT, instance->clks);
1081 		return -EINVAL;
1082 	}
1083 
1084 	return 0;
1085 }
1086 
1087 static int mtk_phy_power_on(struct phy *phy)
1088 {
1089 	struct mtk_phy_instance *instance = phy_get_drvdata(phy);
1090 	struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);
1091 
1092 	if (instance->type == PHY_TYPE_USB2) {
1093 		u2_phy_instance_power_on(tphy, instance);
1094 		hs_slew_rate_calibrate(tphy, instance);
1095 	} else if (instance->type == PHY_TYPE_PCIE) {
1096 		pcie_phy_instance_power_on(tphy, instance);
1097 	}
1098 
1099 	return 0;
1100 }
1101 
1102 static int mtk_phy_power_off(struct phy *phy)
1103 {
1104 	struct mtk_phy_instance *instance = phy_get_drvdata(phy);
1105 	struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);
1106 
1107 	if (instance->type == PHY_TYPE_USB2)
1108 		u2_phy_instance_power_off(tphy, instance);
1109 	else if (instance->type == PHY_TYPE_PCIE)
1110 		pcie_phy_instance_power_off(tphy, instance);
1111 
1112 	return 0;
1113 }
1114 
1115 static int mtk_phy_exit(struct phy *phy)
1116 {
1117 	struct mtk_phy_instance *instance = phy_get_drvdata(phy);
1118 	struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);
1119 
1120 	if (instance->type == PHY_TYPE_USB2)
1121 		u2_phy_instance_exit(tphy, instance);
1122 
1123 	clk_bulk_disable_unprepare(TPHY_CLKS_CNT, instance->clks);
1124 	return 0;
1125 }
1126 
1127 static int mtk_phy_set_mode(struct phy *phy, enum phy_mode mode, int submode)
1128 {
1129 	struct mtk_phy_instance *instance = phy_get_drvdata(phy);
1130 	struct mtk_tphy *tphy = dev_get_drvdata(phy->dev.parent);
1131 
1132 	if (instance->type == PHY_TYPE_USB2)
1133 		u2_phy_instance_set_mode(tphy, instance, mode);
1134 
1135 	return 0;
1136 }
1137 
1138 static struct phy *mtk_phy_xlate(struct device *dev,
1139 					struct of_phandle_args *args)
1140 {
1141 	struct mtk_tphy *tphy = dev_get_drvdata(dev);
1142 	struct mtk_phy_instance *instance = NULL;
1143 	struct device_node *phy_np = args->np;
1144 	int index;
1145 	int ret;
1146 
1147 	if (args->args_count != 1) {
1148 		dev_err(dev, "invalid number of cells in 'phy' property\n");
1149 		return ERR_PTR(-EINVAL);
1150 	}
1151 
1152 	for (index = 0; index < tphy->nphys; index++)
1153 		if (phy_np == tphy->phys[index]->phy->dev.of_node) {
1154 			instance = tphy->phys[index];
1155 			break;
1156 		}
1157 
1158 	if (!instance) {
1159 		dev_err(dev, "failed to find appropriate phy\n");
1160 		return ERR_PTR(-EINVAL);
1161 	}
1162 
1163 	instance->type = args->args[0];
1164 	if (!(instance->type == PHY_TYPE_USB2 ||
1165 	      instance->type == PHY_TYPE_USB3 ||
1166 	      instance->type == PHY_TYPE_PCIE ||
1167 	      instance->type == PHY_TYPE_SATA ||
1168 	      instance->type == PHY_TYPE_SGMII)) {
1169 		dev_err(dev, "unsupported device type: %d\n", instance->type);
1170 		return ERR_PTR(-EINVAL);
1171 	}
1172 
1173 	switch (tphy->pdata->version) {
1174 	case MTK_PHY_V1:
1175 		phy_v1_banks_init(tphy, instance);
1176 		break;
1177 	case MTK_PHY_V2:
1178 	case MTK_PHY_V3:
1179 		phy_v2_banks_init(tphy, instance);
1180 		break;
1181 	default:
1182 		dev_err(dev, "phy version is not supported\n");
1183 		return ERR_PTR(-EINVAL);
1184 	}
1185 
1186 	ret = phy_efuse_get(tphy, instance);
1187 	if (ret)
1188 		return ERR_PTR(ret);
1189 
1190 	phy_parse_property(tphy, instance);
1191 	phy_type_set(instance);
1192 
1193 	return instance->phy;
1194 }
1195 
1196 static const struct phy_ops mtk_tphy_ops = {
1197 	.init		= mtk_phy_init,
1198 	.exit		= mtk_phy_exit,
1199 	.power_on	= mtk_phy_power_on,
1200 	.power_off	= mtk_phy_power_off,
1201 	.set_mode	= mtk_phy_set_mode,
1202 	.owner		= THIS_MODULE,
1203 };
1204 
1205 static const struct mtk_phy_pdata tphy_v1_pdata = {
1206 	.avoid_rx_sen_degradation = false,
1207 	.version = MTK_PHY_V1,
1208 };
1209 
1210 static const struct mtk_phy_pdata tphy_v2_pdata = {
1211 	.avoid_rx_sen_degradation = false,
1212 	.sw_efuse_supported = true,
1213 	.version = MTK_PHY_V2,
1214 };
1215 
1216 static const struct mtk_phy_pdata tphy_v3_pdata = {
1217 	.sw_efuse_supported = true,
1218 	.version = MTK_PHY_V3,
1219 };
1220 
1221 static const struct mtk_phy_pdata mt8173_pdata = {
1222 	.avoid_rx_sen_degradation = true,
1223 	.version = MTK_PHY_V1,
1224 };
1225 
1226 static const struct mtk_phy_pdata mt8195_pdata = {
1227 	.sw_pll_48m_to_26m = true,
1228 	.sw_efuse_supported = true,
1229 	.version = MTK_PHY_V3,
1230 };
1231 
1232 static const struct of_device_id mtk_tphy_id_table[] = {
1233 	{ .compatible = "mediatek,mt2701-u3phy", .data = &tphy_v1_pdata },
1234 	{ .compatible = "mediatek,mt2712-u3phy", .data = &tphy_v2_pdata },
1235 	{ .compatible = "mediatek,mt8173-u3phy", .data = &mt8173_pdata },
1236 	{ .compatible = "mediatek,mt8195-tphy", .data = &mt8195_pdata },
1237 	{ .compatible = "mediatek,generic-tphy-v1", .data = &tphy_v1_pdata },
1238 	{ .compatible = "mediatek,generic-tphy-v2", .data = &tphy_v2_pdata },
1239 	{ .compatible = "mediatek,generic-tphy-v3", .data = &tphy_v3_pdata },
1240 	{ },
1241 };
1242 MODULE_DEVICE_TABLE(of, mtk_tphy_id_table);
1243 
1244 static int mtk_tphy_probe(struct platform_device *pdev)
1245 {
1246 	struct device *dev = &pdev->dev;
1247 	struct device_node *np = dev->of_node;
1248 	struct device_node *child_np;
1249 	struct phy_provider *provider;
1250 	struct resource *sif_res;
1251 	struct mtk_tphy *tphy;
1252 	struct resource res;
1253 	int port, retval;
1254 
1255 	tphy = devm_kzalloc(dev, sizeof(*tphy), GFP_KERNEL);
1256 	if (!tphy)
1257 		return -ENOMEM;
1258 
1259 	tphy->pdata = of_device_get_match_data(dev);
1260 	if (!tphy->pdata)
1261 		return -EINVAL;
1262 
1263 	tphy->nphys = of_get_child_count(np);
1264 	tphy->phys = devm_kcalloc(dev, tphy->nphys,
1265 				       sizeof(*tphy->phys), GFP_KERNEL);
1266 	if (!tphy->phys)
1267 		return -ENOMEM;
1268 
1269 	tphy->dev = dev;
1270 	platform_set_drvdata(pdev, tphy);
1271 
1272 	sif_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
1273 	/* SATA phy of V1 needn't it if not shared with PCIe or USB */
1274 	if (sif_res && tphy->pdata->version == MTK_PHY_V1) {
1275 		/* get banks shared by multiple phys */
1276 		tphy->sif_base = devm_ioremap_resource(dev, sif_res);
1277 		if (IS_ERR(tphy->sif_base)) {
1278 			dev_err(dev, "failed to remap sif regs\n");
1279 			return PTR_ERR(tphy->sif_base);
1280 		}
1281 	}
1282 
1283 	if (tphy->pdata->version < MTK_PHY_V3) {
1284 		tphy->src_ref_clk = U3P_REF_CLK;
1285 		tphy->src_coef = U3P_SLEW_RATE_COEF;
1286 		/* update parameters of slew rate calibrate if exist */
1287 		device_property_read_u32(dev, "mediatek,src-ref-clk-mhz",
1288 					 &tphy->src_ref_clk);
1289 		device_property_read_u32(dev, "mediatek,src-coef",
1290 					 &tphy->src_coef);
1291 	}
1292 
1293 	port = 0;
1294 	for_each_child_of_node(np, child_np) {
1295 		struct mtk_phy_instance *instance;
1296 		struct clk_bulk_data *clks;
1297 		struct device *subdev;
1298 		struct phy *phy;
1299 
1300 		instance = devm_kzalloc(dev, sizeof(*instance), GFP_KERNEL);
1301 		if (!instance) {
1302 			retval = -ENOMEM;
1303 			goto put_child;
1304 		}
1305 
1306 		tphy->phys[port] = instance;
1307 
1308 		phy = devm_phy_create(dev, child_np, &mtk_tphy_ops);
1309 		if (IS_ERR(phy)) {
1310 			dev_err(dev, "failed to create phy\n");
1311 			retval = PTR_ERR(phy);
1312 			goto put_child;
1313 		}
1314 
1315 		subdev = &phy->dev;
1316 		retval = of_address_to_resource(child_np, 0, &res);
1317 		if (retval) {
1318 			dev_err(subdev, "failed to get address resource(id-%d)\n",
1319 				port);
1320 			goto put_child;
1321 		}
1322 
1323 		instance->port_base = devm_ioremap_resource(subdev, &res);
1324 		if (IS_ERR(instance->port_base)) {
1325 			retval = PTR_ERR(instance->port_base);
1326 			goto put_child;
1327 		}
1328 
1329 		instance->phy = phy;
1330 		instance->index = port;
1331 		phy_set_drvdata(phy, instance);
1332 		port++;
1333 
1334 		clks = instance->clks;
1335 		clks[0].id = "ref";     /* digital (& analog) clock */
1336 		clks[1].id = "da_ref";  /* analog clock */
1337 		retval = devm_clk_bulk_get_optional(subdev, TPHY_CLKS_CNT, clks);
1338 		if (retval)
1339 			goto put_child;
1340 
1341 		retval = phy_type_syscon_get(instance, child_np);
1342 		if (retval)
1343 			goto put_child;
1344 	}
1345 
1346 	provider = devm_of_phy_provider_register(dev, mtk_phy_xlate);
1347 
1348 	return PTR_ERR_OR_ZERO(provider);
1349 put_child:
1350 	of_node_put(child_np);
1351 	return retval;
1352 }
1353 
1354 static struct platform_driver mtk_tphy_driver = {
1355 	.probe		= mtk_tphy_probe,
1356 	.driver		= {
1357 		.name	= "mtk-tphy",
1358 		.of_match_table = mtk_tphy_id_table,
1359 	},
1360 };
1361 
1362 module_platform_driver(mtk_tphy_driver);
1363 
1364 MODULE_AUTHOR("Chunfeng Yun <chunfeng.yun@mediatek.com>");
1365 MODULE_DESCRIPTION("MediaTek T-PHY driver");
1366 MODULE_LICENSE("GPL v2");
1367